© Semiconductor Components Industries, LLC, 2008
February, 2008 - Rev. 28
1Publication Order Number:
TL431/D
TL431, A, B Series,
NCV431A, B
Programmable
Precision References
The TL431, A, B integrated circuits are three-terminal
programmable shunt regulator diodes. These monolithic IC voltage
references operate as a low temperature coefficient zener which is
programmable from Vref to 36 V with two external resistors. These
devices exhibit a wide operating current range of 1.0mA to 100 mA
with a typical dynamic impedance of 0.22 W. The characteristics of
these references make them excellent replacements for zener diodes in
many applications such as digital voltmeters, power supplies, and op
amp circuitry. The 2.5 V reference makes it convenient to obtain a
stable reference from 5.0 V logic supplies, and since the TL431, A, B
operates as a shunt regulator, it can be used as either a positive or
negative voltage reference.
Features
•Programmable Output Voltage to 36 V
•Voltage Reference Tolerance: ±0.4%, Typ @ 25°C (TL431B)
•Low Dynamic Output Impedance, 0.22 W Typical
•Sink Current Capability of 1.0 mA to 100 mA
•Equivalent Full-Range Temperature Coefficient of 50 ppm/°C Typical
•Temperature Compensated for Operation over Full Rated Operating
Temperature Range
•Low Output Noise Voltage
•Pb-Free Packages are Available (Top View)
3
1Reference
N/C
N/C
N/C
2
4
8
7
6
5N/C
Anode
N/C
Cathode
Anode Anode
TO-92 (TO-226)
LP SUFFIX
CASE 29
PDIP-8
P SUFFIX
CASE 626
SOIC-8
D SUFFIX
CASE 751
Pin 1. Reference
2. Anode
3. Cathode
(Top View)
3
1Reference
N/C
2
4
8
7
6
5N/C
Cathode
Micro8E
DM SUFFIX
CASE 846A
8
1
8
1
8
1
123
This is an internally modified SOIC-8 package. Pins 2, 3, 6 and
7 are electrically common to the die attach flag. This internal
lead frame modification increases power dissipation capability
when appropriately mounted on a printed circuit board. This
modified package conforms to all external dimensions of the
standard SOIC-8 package.
http://onsemi.com
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
ORDERING INFORMATION
See general marking information in the device marking
section on page 16 of this data sheet.
DEVICE MARKING INFORMATION
TL431, A, B Series, NCV431A, B
http://onsemi.com
2
Representative Block Diagram
1.0 k
Cathode
(K)
2.5 Vref
Anode (A)
Reference
(R)
4.0 k
150
Symbol
10 k
20 pF
800
Cathode (K)
3.28 k
Representative Schematic Diagram
Component values are nominal
Anode (A)
-
+
Anode
(A)
800
Reference
(R)
2.4 k 7.2 k
20 pF
800
Cathode
(K)
Reference
(R)
This device contains 12 active transistors.
MAXIMUM RATINGS (Full operating ambient temperature range applies, unless otherwise noted.)
Rating Symbol Value Unit
Cathode to Anode Voltage VKA 37 V
Cathode Current Range, Continuous IK-100 to +150 mA
Reference Input Current Range, Continuous Iref -0.05 to +10 mA
Operating Junction Temperature TJ150 °C
Operating Ambient Temperature Range TA°C
TL431I, TL431AI, TL431BI -40 to +85
TL431C, TL431AC, TL431BC 0 to +70
NCV431AI, NCV431B, TL431BV -40 to +125
Storage Temperature Range Tstg -65 to +150 °C
Total Power Dissipation @ TA = 25°C PDW
Derate above 25°C Ambient Temperature
D, LP Suffix Plastic Package 0.70
P Suffix Plastic Package 1.10
DM Suffix Plastic Package 0.52
Total Power Dissipation @ TC = 25°C PDW
Derate above 25°C Case Temperature
D, LP Suffix Plastic Package 1.5
P Suffix Plastic Package 3.0
ESD Rating HBM
MM
>2000
>200
V
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
RECOMMENDED OPERATING CONDITIONS
Condition Symbol Min Max Unit
Cathode to Anode Voltage VKA Vref 36 V
Cathode Current IK1.0 100 mA
THERMAL CHARACTERISTICS
Characteristic Symbol
D, LP Suffix
Package
P Suffix
Package
DM Suffix
Package Unit
Thermal Resistance, Junction-to-Ambient RqJA 178 114 240 °C/W
Thermal Resistance, Junction-to-Case RqJC 83 41 - °C/W
TL431, A, B Series, NCV431A, B
http://onsemi.com
3
ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise noted.)
Characteristic Symbol
TL431, A, B Series, NCV431A, B
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise noted.)
Characteristic Symbol
TL431AI / NCV431AI TL431AC
TL431BI / TL431BV
NCV431BV
Unit
TL431, A, B Series, NCV431A, B
http://onsemi.com
5
IK
Vref
VKA
Input
Figure 1. Test Circuit for VKA = Vref
Input
IK
R2
Iref
Vref
VKA
R1
Figure 2. Test Circuit for VKA > Vref
VKA +Vrefǒ1 )R1
R2Ǔ)IrefSR1
Ioff
Input VKA
Figure 3. Test Circuit for Ioff
-1.0
IMin
200
400
VKA, CATHODE VOLTAGE (V)
-200 0
0
1.0 2.0 3.0
800
600
-2.0 -1.0 0
-100 1.0 2.0 3.0
150
50
VKA, CATHODE VOLTAGE (V)
0
-50
Figure 4. Cathode Current versus
Cathode Voltage
Figure 5. Cathode Current versus
Cathode Voltage
Input
100
VKA = Vref
TA = 25°C
IK
VKA
IK, CATHODE CURRENT (mA)
IK, CATHODE CURRENT ( A)μ
125
TA, AMBIENT TEMPERATURE (°C)
3.0
10050 75-55
0
2.5
0.5
2.0
1.0
250-25
1.5
2600
2580
2560
2540
2520
2500
2480
2460
VKA = Vref
IK = 10 mA
TA, AMBIENT TEMPERATURE (°C)
VKA
IK
-55
Input
Vref
75 100 125
2440
050
Figure 6. Reference Input Voltage versus
Ambient Temperature
Figure 7. Reference Input Current versus
Ambient Temperature
2420
2400 25-25
Input
IK
IK = 10 mA
Iref
10k
VKA
ref
V , REFERENCE INPUT VOLTAGE (mV)
Iref, REFERENCE INPUT CURRENT ( A)μ
Vref Max = 2550 mV
Vref Typ = 2495 mV
Vref Min = 2440 mV
VKA = Vref
TA = 25°C
Input VKA
IK
TL431, A, B Series, NCV431A, B
http://onsemi.com
6
√
NOISE VOLTAGE (nV/ Hz)
-55
f, FREQUENCY (MHz)
100
10
1.0
100 k 10 M1.0 M
TL431, A, B Series, NCV431A, B
http://onsemi.com
7
Input
Output
t, TIME (ms)
Pulse
Generator
f = 100 kHz
0 8.04.0 20
0
16
2.0
3.0
12
0
1.0
5.0
Figure 14. Pulse Response Figure 15. Stability Boundary Conditions
50
220 Output
GND
Input
Monitor
TA = 25°C
VOLTAGE SWING (V)
TA = 25°C
C
A
B
CL, LOAD CAPACITANCE
120
80
100
60
0
IK, CATHODE CURRENT (mA)
140
1.0 nF 100 mF1.0 mF10 mF
Stable Stable
40
20
10 nF 100 nF
A
B
D
Unstable
Area
Programmed
VKA(V)
A
B
C
D
Vref
5.0
10
15
Figure 16. Test Circuit For Curve A
of Stability Boundary Conditions
Figure 17. Test Circuit For Curves B, C, And D
of Stability Boundary Conditions
V+
IK
150
IK
V+
150
CL
10 k
CL
Figure 18. Shunt Regulator Figure 19. High Current Shunt Regulator
V+ Vout
R1
V+ Vout
R1
R2
R2
Vout +ǒ1)R1
R2ǓVref Vout +ǒ1)R1
R2ǓVref
TYPICAL APPLICATIONS
TL431, A, B Series, NCV431A, B
http://onsemi.com
8
Figure 20. Output Control for a
Three-Terminal Fixed Regulator
Figure 21. Series Pass Regulator
V+ Vout
R1
R2
Out
In
MC7805
V+ Vout
R2
Common
R1
Vout +ǒ1)R1
R2ǓVref
Vout(min) +Vref )5.0V
Vout +ǒ1)R1
R2ǓVref
Vout(min) +Vref
Vin(min) +Vout )Vbe
Figure 22. Constant Current Source Figure 23. Constant Current Sink
V+
RCL Iout
V+
RS
ISink +Vref
RS
Iout +Vref
RCL
Isink
Figure 24. TRIAC Crowbar Figure 25. SRC Crowbar
Vout
V+
R2
V+ Vout
R1
R2
R1
Vout(trip) +ǒ1)R1
R2ǓVref
Vout(trip) +ǒ1)R1
R2ǓVref
TL431, A, B Series, NCV431A, B
http://onsemi.com
9
Figure 26. Voltage Monitor Figure 27. Single-Supply Comparator with
Temperature-Compensated Threshold
Vth = Vref
V+
Vout
Vin
R1 R3
V+ Vout
R2 R4
l
L.E.D. indicator is `on' when V+ is between the
upper and lower limits.
LowerLimit +ǒ1)R1
R2ǓVref
UpperLimit +ǒ1)R3
R4ǓVref
Vin Vout
< Vref V+
> Vref ≈2.0 V
Figure 28. Linear Ohmmeter Figure 29. Simple 400 mW Phono Amplifier
*Thermalloy
*THM 6024
*Heatsink on
*LP Package
*
Tl = 330 to 8.0 W
8.0 W
+
-
LM11
2.0 mA
25 V
25 V
-5.0 V
Vout
Range
V
1.0 MW
V
100 kW
V
V
1.0 kW
RX
5.0 M
1%
500 k
1%
50 k
1%
5.0 k
1%
47 k
Tone
0.05 mF
470 mF
Volume
1N5305
1.0 mF
TI
360 k
330
56 k 10 k 25 k
38 V
+
10 kW
10 k
Calibrate
Rx+VoutD W
V Range
TL431, A, B Series, NCV431A, B
http://onsemi.com
10
Figure 30. High Efficiency Step-Down Switching Converter
150 mH @ 2.0 A
1N5823
0.01mF
+
470 mF
51 k
0.1 mF
+2200 mF
4.7 k
Vin = 10 V to 20 V TIP115
MPSA20
1.0 k
4.7 k
4.7 k
102.2 k
100 k
Vout = 5.0 V
Iout = 1.0 A
Test Conditions Results
Line Regulation Vin = 10 V to 20 V, Io = 1.0 A 53 mV (1.1%)
Load Regulation Vin = 15 V, Io = 0 A to 1.0 A 25 mV (0.5%)
Output Ripple Vin = 10 V, Io = 1.0 A 50 mVpp P.A.R.D.
Output Ripple Vin = 20 V, Io = 1.0 A 100 mVpp P.A.R.D.
Efficiency Vin = 15 V, Io = 1.0 A 82%
TL431, A, B Series, NCV431A, B
http://onsemi.com
11
APPLICATIONS INFORMATION
The TL431 is a programmable precision reference which
is used in a variety of ways. It serves as a reference voltage
in circuits where a non-standard reference voltage is
needed. Other uses include feedback control for driving an
optocoupler in power supplies, voltage monitor, constant
current source, constant current sink and series pass
regulator. In each of these applications, it is critical to
maintain stability of the device at various operating currents
and load capacitances. In some cases the circuit designer can
estimate the stabilization capacitance from the stability
boundary conditions curve provided in Figure 15. However,
these typical curves only provide stability information at
specific cathode voltages and at a specific load condition.
Additional information is needed to determine the
capacitance needed to optimize phase margin or allow for
process variation.
A simplified model of the TL431 is shown in Figure 31.
When tested for stability boundaries, the load resistance is
150 W. The model reference input consists of an input
transistor and a dc emitter resistance connected to the device
anode. A dependent current source, Gm, develops a current
whose amplitude is determined by the difference between
the 1.78 V internal reference voltage source and the input
transistor emitter voltage. A portion of Gm flows through
compensation capacitance, CP2. The voltage across CP2
drives the output dependent current source, Go, which is
connected across the device cathode and anode.
Model component values are:
Vref = 1.78 V
Gm = 0.3 + 2.7 exp (-IC/26 mA)
where IC is the device cathode current and Gm is in mhos
Go = 1.25 (Vcp2) mmhos.
Resistor and capacitor typical values are shown on the
model. Process tolerances are ±20% for resistors, ±10% for
capacitors, and ±40% for transconductances.
An examination of the device model reveals the location
of circuit poles and zeroes:
P1 +1
2pRGMCP1 +1
2p* 1.0M * 20pF +7.96kHz
P2 +1
2pRP2CP2 +1
2p* 10M * 0.265pF +60kHz
Z1 +1
2pRZ1CP1 +1
2p* 15.9k * 20pF +500kHz
In addition, there is an external circuit pole defined by the
load:
PL+1
2pRLCL
Also, the transfer dc voltage gain of the TL431 is:
G+GMRGMGoRL
Example 1:
I
C
+10mA, RL+230W,C
L+0.Definethetransfergain.
The DC gain is:
G+GMRGMGoRL+
(2.138)(1.0M)(1.25m)(230) +615 +56dB
Loopgain +G 8.25k
8.25k )15k +218 +47dB
The resulting transfer function Bode plot is shown in
Figure 32. The asymptotic plot may be expressed as the
following equation:
Av +615 ǒ1)jf
500kHzǓ
ǒ1)jf
8.0kHzǓǒ1)jf
60kHzǓ
The Bode plot shows a unity gain crossover frequency of
approximately 600 kHz. The phase margin, calculated from
the equation, would be 55.9 degrees. This model matches the
Open-Loop Bode Plot of Figure 12. The total loop would
have a unity gain frequency of about 300 kHz with a phase
margin of about 44 degrees.
TL431, A, B Series, NCV431A, B
http://onsemi.com
12
Figure 31. Simplified TL431 Device Model
+
RL
VCC
-
CL
15 k
9.0 mF
Input
8.25 k
3
Cathode
500 k
Vref
1.78 V
Rref
16
GM
Anode 2
RGM
1.0 M
Ref
1
Go
1.0 mmho
CP2
0.265 pF
RP2
10 M
RZ1
15.9 k
CP1
20 pF
f, FREQUENCY (Hz)
102
101
-20
30
20
60
0
Av, OPEN-LOOP VOLTAGE GAIN (dB)
Figure 32. Example 1 Circuit Open Loop Gain Plot
TL431 OPEN-LOOP VOLTAGE GAIN VERSUS FREQUENCY
40
104
103107
105106
10
-10
50
Example 2.
IC = 7.5 mA, RL = 2.2 kW, CL = 0.01 mF. Cathode tied to
reference input pin. An examination of the data sheet
stability boundary curve (Figure 15) shows that this value of
load capacitance and cathode current is on the boundary.
Define the transfer gain.
The DC gain is:
G+GMRGMGoRL+
(2.323)(1.0M)(1.25m)(2200) +6389 +76dB
The resulting open loop Bode plot is shown in Figure 33.
The asymptotic plot may be expressed as the following
equation:
Av +615 ǒ1)jf
500kHzǓ
ǒ1)jf
8.0kHzǓǒ1)jf
60kHzǓǒ1)jf
7.2kHzǓ
Note that the transfer function now has an extra pole
formed by the load capacitance and load resistance.
Note that the crossover frequency in this case is about
250 kHz, having a phase margin of about -46 degrees.
Therefore, instability of this circuit is likely.
f, FREQUENCY (Hz)
102
101
-20
40
20
80
0
Av, OPEN-LOOP GAIN (dB)
Figure 33. Example 2 Circuit Open Loop Gain Plot
TL431 OPEN-LOOP BODE PLOT WITH LOAD CAP
60
104
103106
105
With three poles, this system is unstable. The only hope
for stabilizing this circuit is to add a zero. However, that can
only be done by adding a series resistance to the output
capacitance, which will reduce its effectiveness as a noise
filter. Therefore, practically, in reference voltage
applications, the best solution appears to be to use a smaller
value of capacitance in low noise applications or a very
large value to provide noise filtering and a dominant pole
rolloff of the system.
TL431, A, B Series, NCV431A, B
http://onsemi.com
13
ORDERING INFORMATION
Device Operating Temperature Range Package Code Shipping Information†Tolerance
TL431ACD
0°C to 70°C
SOIC-8
98 Units / Rail
1.0%
TL431ACDG SOIC-8
(Pb-Free)
TL431BCD SOIC-8
0.4%
TL431BCDG SOIC-8
(Pb-Free)
TL431CD SOIC-8 2.2%
TL431CDG SOIC-8
(Pb-Free) 2.2%
TL431ACDR2 SOIC-8
2500 Units / Tape & Reel
1.0%
TL431ACDR2G SOIC-8
(Pb-Free)
TL431BCDR2 SOIC-8
0.4%
TL431BCDR2G SOIC-8
(Pb-Free)
TL431CDR2 SOIC-8
2.2%
TL431CDR2G SOIC-8
(Pb-Free)
TL431ACDMR2 Micro8
4000 Units / Tape & Reel
1.0%
TL431ACDMR2G Micro8
(Pb-Free) 1.0%
TL431BCDMR2 Micro8
0.4%
TL431BCDMR2G Micro8
(Pb-Free)
TL431CDMR2 Micro8
2.2%
TL431CDMR2G Micro8
(Pb-Free)
TL431ACP PDIP-8
50 Units / Rail
1.0%
TL431ACPG PDIP-8
(Pb-Free) 1.0%
TL431BCP PDIP-8 0.4%
TL431BCPG PDIP-8
(Pb-Free) 0.4%
TL431CP PDIP-8
2.2%
TL431CPG PDIP-8
(Pb-Free)
TL431ACLP TO-92 (TO-226)
2000 Units / Bag
1.0%
TL431ACLPG TO-92 (TO-226)
(Pb-Free)
TL431BCLP TO-92 (TO-226)
0.4%
TL431BCLPG TO-92 (TO-226)
(Pb-Free)
TL431CLP TO-92 (TO-226)
2.2%
TL431CLPG TO-92 (TO-226)
(Pb-Free)
TL431ACLPRA TO-92 (TO-226)
2000 Units / Tape & Reel 1.0%
TL431ACLPRAG TO-92 (TO-226)
(Pb-Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
TL431, A, B Series, NCV431A, B
http://onsemi.com
14
ORDERING INFORMATION
Device Operating Temperature Range Package Code Shipping Information†Tolerance
TL431BCLPRA
0°C to 70°C
TO-92 (TO-226)
2000 Units / Tape & Reel
0.4%
TL431BCLPRAG TO-92 (TO-226)
(Pb-Free)
TL431CLPRA TO-92 (TO-226)
2.2%
TL431CLPRAG TO-92 (TO-226)
(Pb-Free)
TL431ACLPRE TO-92 (TO-226)
1.0%
TL431ACLPREG TO-92 (TO-226)
(Pb-Free)
TL431BCLPRE TO-92 (TO-226) 0.4%
TL431BCLPREG TO-92 (TO-226)
(Pb-Free) 0.4%
TL431ACLPRP TO-92 (TO-226)
2000 / Tape & Ammo Box 1.0%
TL431ACLPRPG TO-92 (TO-226)
(Pb-Free)
TL431BCLPRM TO-92 (TO-226)
2000 Units / Fan-Fold
0.4%
TL431BCLPRMG TO-92 (TO-226)
(Pb-Free)
TL431CLPRP TO-92 (TO-226)
2.2%
TL431CLPRPG TO-92 (TO-226)
(Pb-Free)
TL431AID
-40°C to 85°C
SOIC-8
98 Units / Rail
1.0%
TL431AIDG SOIC-8
(Pb-Free) 1.0%
TL431BID SOIC-8
0.4%
TL431BIDG SOIC-8
(Pb-Free)
TL431ID SOIC-8
2.2%
TL431IDG SOIC-8
(Pb-Free)
TL431AIDR2 SOIC-8
2500 Units / Tape & Reel
1.0%
TL431AIDR2G SOIC-8
(Pb-Free)
TL431BIDR2 SOIC-8
0.4%
TL431BIDR2G SOIC-8
(Pb-Free)
TL431IDR2 SOIC-8
2.2%
TL431IDR2G SOIC-8
(Pb-Free)
TL431AIDMR2 Micro8
4000 Units / Tape & Reel
1.0%
TL431AIDMR2G Micro8
(Pb-Free) 1.0%
TL431BIDMR2 Micro8
0.4%
TL431BIDMR2G Micro8
(Pb-Free)
TL431IDMR2 Micro8
2.2%
TL431IDMR2G Micro8
(Pb-Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
TL431, A, B Series, NCV431A, B
http://onsemi.com
15
ORDERING INFORMATION
Device Operating Temperature Range Package Code Shipping Information†Tolerance
TL431AIP
-40°C to 85°C
PDIP-8
50 Units / Rail
1.0%
TL431AIPG PDIP-8
(Pb-Free)
TL431BIP PDIP-8 0.4%
TL431BIPG PDIP-8
(Pb-Free) 0.4%
TL431IP PDIP-8 2.2%
TL431IPG PDIP-8
(Pb-Free) 2.2%
TL431AILP TO-92 (TO-226)
2000 Units / Bag
1.0%
TL431AILPG TO-92 (TO-226) 1.0%
TL431BILP TO-92 (TO-226)
0.4%
TL431BILPG TO-92 (TO-226)
(Pb-Free)
TL431ILP TO-92 (TO-226)
2.2%
TL431ILPG TO-92 (TO-226)
(Pb-Free)
TL431AILPRA TO-92 (TO-226)
2000 Units / Tape & Reel
1.0%
TL431AILPRAG TO-92 (TO-226)
(Pb-Free)
TL431BILPRA TO-92 (TO-226)
0.4%
TL431BILPRAG TO-92 (TO-226)
(Pb-Free)
TL431ILPRA TO-92 (TO-226)
2.2%
TL431ILPRAG TO-92 (TO-226)
(Pb-Free)
TL431AILPRM TO-92 (TO-226)
2000 / Tape & Ammo Box
1.0%
TL431AILPRMG TO-92 (TO-226)
(Pb-Free) 1.0%
TL431AILPRP TO-92 (TO-226) 1.0%
TL431AILPRPG TO-92 (TO-226)
(Pb-Free) 1.0%
TL431ILPRP TO-92 (TO-226) 2.2%
TL431ILPRPG TO-92 (TO-226)
(Pb-Free) 2.2%
TL431BVD
-40°C to 125°C
SOIC-8
98 Units / Rail
0.4%
TL431BVDG SOIC-8
(Pb-Free) 0.4%
TL431BVDR2 SOIC-8
2500 Units / Tape & Reel
0.4%
TL431, A, B Series, NCV431A, B
http://onsemi.com
16
ORDERING INFORMATION
Device Operating Temperature Range Package Code Shipping Information†Tolerance
TL431BVP
-40°C to 125°C
PDIP-8
50 Units / Rail
0.4%
TL431BVPG PDIP-8
(Pb-Free) 0.4%
NCV431AIDMR2 Micro8
4000 Units / Tape & Reel
1%
NCV431AIDMR2G Micro8
(Pb-Free) 1%
NCV431AIDR2 SOIC-8
2500 Units / Tape & Reel
1%
NCV431AIDR2G SOIC-8
(Pb-Free) 1%
NCV431BVDMR2G Micro8
(Pb-Free) 4000 Units / Tape & Reel 0.4%
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
SOIC-8
D SUFFIX
CASE 751
MARKING DIAGRAMS
Micro8
CASE 846A
TO-92 (TO-226)
CASE 29
PDIP-8
CASE 626
TL431xx
AWL
YYWWG
1
8
TL431
xxxx
YWWG
G
xxxx = Specific Device Code
A = Assembly Location
Y, YY = Year
WW, W = Work Week
G or G = Pb-Free Package
(Note: Microdot may be in either location)
xxx
AYWG
G
1
8
431xx
ALYW
G
1
8
TL431
ALYWx
G
1
8
(Exception for the TL431CD
and TL431ID only)
TL431, A, B Series, NCV431A, B
http://onsemi.com
17
PACKAGE DIMENSIONS
TO-92 (TO-226)
CASE 29-11
ISSUE AM
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. CONTOUR OF PACKAGE BEYOND DIMENSION R
IS UNCONTROLLED.
4. LEAD DIMENSION IS UNCONTROLLED IN P AND
TL431, A, B Series, NCV431A, B
http://onsemi.com
18
PACKAGE DIMENSIONS
PDIP-8
P SUFFIX
PLASTIC PACKAGE
CASE 626-05
ISSUE L
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
14
58
F
NOTE 2 -A-
-B-
-T-
SEATING
PLANE
H
J
G
DK
N
C
L
M
M
A
M
0.13 (0.005) B M
T
DIM MIN MAX MIN MAX
INCHESMILLIMETERS
A9.40 10.16 0.370 0.400
B6.10 6.60 0.240 0.260
C3.94 4.45 0.155 0.175
D0.38 0.51 0.015 0.020
F1.02 1.78 0.040 0.070
G2.54 BSC 0.100 BSC
H0.76 1.27 0.030 0.050
J0.20 0.30 0.008 0.012
K2.92 3.43 0.115 0.135
L7.62 BSC 0.300 BSC
M--- 10 --- 10
N0.76 1.01 0.030 0.040
__
TL431, A, B Series, NCV431A, B
http://onsemi.com
19
PACKAGE DIMENSIONS
Micro8
DM SUFFIX
PLASTIC PACKAGE
CASE 846A-02
ISSUE G
8X 8X
6X ǒmm
inchesǓ
SCALE 8:1
1.04
0.041
0.38
0.015
5.28
0.208
4.24
0.167
3.20
0.126
0.65
0.0256
*For additional information on our Pb-Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
S
B
M
0.08 (0.003) A S
T
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED
0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
b
e
PIN 1 ID
8 PL
0.038 (0.0015)
-T-
SEATING
PLANE
A
A1 cL
DIM
A
MIN NOM MAX MIN
MILLIMETERS
-- -- 1.10 --
INCHES
A1 0.05 0.08 0.15 0.002
b0.25 0.33 0.40 0.010
c0.13 0.18 0.23 0.005
D2.90 3.00 3.10 0.114
E2.90 3.00 3.10 0.114
e0.65 BSC
L0.40 0.55 0.70 0.016
-- 0.043
0.003 0.006
0.013 0.016
0.007 0.009
0.118 0.122
0.118 0.122
0.026 BSC
0.021 0.028
NOM MAX
4.75 4.90 5.05 0.187 0.193 0.199
HE
HE
DD
E
TL431, A, B Series, NCV431A, B
http://onsemi.com
20
PACKAGE DIMENSIONS
SOIC-8
D SUFFIX
PLASTIC PACKAGE
CASE 751-07
ISSUE AJ