DS26LS31MQML DS26LS31MQML Quad High Speed Differential Line Driver Literature Number: SNOSAM5A DS26LS31MQML Quad High Speed Differential Line Driver General Description Features The DS26LS31MQML is a quad differential line driver designed for digital data transmission over balanced lines. The DS26LS31MQML meets all the requirements of EIA Standard RS-422 and Federal Standard 1020. It is designed to provide unipolar differential drive to twisted-pair or parallelwire transmission lines. n Operation from single 5V supply n Outputs won't load line when VCC = 0V n Four line drivers in one package for maximum package density n Output short-circuit protection n Complementary outputs n Meets the requirements of EIA Standard RS-422 n Pin compatible with AM26LS31 n Glitch free power up/down The circuit provides an enable and disable function common to all four drivers. The DS26LS31MQML features TRISTATE (R) outputs and logically ANDed complementary outputs. The inputs are all LS compatible and are all one unit load. The DS26LS31 features a power up/down protection circuit which keeps the output in a high impedance stat (TRISTATE) during power up or down preventing erroneous glitches on the transmission lines. Ordering Information NS PART NUMBER SMD PART NUMBER NS PACKAGE NUMBER DS26LS31MEFQML 5962F7802301Q2A 300k rd(Si) E20A DS26LS31ME-SMD DS26LS31MJFQML DS26LS31MJ-SMD DS26LS31MJFQMLV DS26LS31MJ-QMLV DS26LS31MWFQML DS26LS31MW-SMD DS26LS31MWFQMLV DS26LS31MW-QMLV 5962-7802301Q2A 5962F7802301MEA 300k rd(Si) 5962-7802301MEA 5962F7802301VEA 300k rd(Si) 5962-7802301VEA 5962F7802301MFA 300k rd(Si) 5962-7802301MFA 5962F7802301VFA 300k rd(Si) 5962-7802301VFA E20A J16A J16A J16A J16A W16A W16A W16A PACKAGE DISCRIPTION 20LD Ceramic Leadless Chip Carrier 20LD Ceramic Leadless Chip Carrier 16LD Ceramic Dual-In-Line 16LD Ceramic Dual-In-Line 16LD Ceramic Dual-In-Line 16LD Ceramic Dual-In-Line 16LD Ceramic Flatpak 16LD Ceramic Flatpak 16LD Ceramic Flatpak W16A 16LD Ceramic Flatpak DS26LS31MJ/883 J16A 16LD Ceramic Dual-in-line DS26LS31MW/883 W16A 16LD Ceramic Flatpak TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 2006 National Semiconductor Corporation DS201412 www.national.com DS26LS31MQML Quad High Speed Differential Line Driver March 2006 DS26LS31MQML Logic and Connection Diagrams 20141201 Dual-In-Line Package 20141202 Top View See NS Package E20A, J16A or W16A www.national.com 2 DS26LS31MQML Absolute Maximum Ratings (Note 1) Supply Voltage 7V Input Voltage 7V Output Voltage 5.5V Output Voltage (Power OFF) -0.25 to 6V Maximum Power Dissipation at 25C (Note 2) J Package 1400 mW LCC Package 1600 mW W Package 850 mW Junction Temperature (TJ) +150C Thermal Resistance, Junction-to-Ambient JA J Package 94C/W derate above +25C at 10.6 mW/C LCC Package 83C/W derate above +25C at 12 mW/C W Package 163C/W derate above +25C at 6.1 mW/C Thermal Resistance, Junction-to-Case JC J Package 16C/W LCC Package 19C/W W Package 14C/W ESD Tolerance 2500V Recommended Operating Conditions Supply Voltage, VCC 4.5 V to 5.5 V Temperature, TA -55C to +125C Radiation Features DS26LS31MEFQML 300 Krads (Si) DS26LS31MJFQML 300 Krads (Si) DS26LS31MJFQMLV 300 Krads (Si) DS26LS31MWFQML 300 Krads (Si) DS26LS31MWFQMLV 300 Krads (Si) 3 www.national.com DS26LS31MQML Quality Conformance Inspection MIL-STD-883, Method 5005 - Group A Subgroup Description 1 Static tests at Temp (C) +25 2 Static tests at +125 3 Static tests at -55 4 Dynamic tests at +25 5 Dynamic tests at +125 6 Dynamic tests at -55 7 Functional tests at +25 8A Functional tests at +125 8B Functional tests at -55 9 Switching tests at +25 10 Switching tests at +125 11 Switching tests at -55 DS26LS31M - SMD, QMLV & RH Electrical Characteristics DC Parameters The following conditions apply, unless otherwise specified. +V = 5V, VCM = 0V. (Note 5) Units Subgroups V 1, 2, 3 .8 V 1, 2, 3 V 1, 2, 3 .5 V 1, 2, 3 -2.0 20 uA 1, 2, 3 1, 2, 3 Symbol Parameters Conditions Notes Min VIH Logical "1" Input Voltage VCC = 4.5V (Notes 3, 4) 2 VIL Logical "0" Input Voltage VCC = 5.5V (Notes 3, 4) Max VOH Logical "1" Output Voltage VCC = 4.5V, IOH = -20mA (Note 4) VOL Logical "0" Output Voltage VCC = 4.5V, IOL = 20mA (Note 4) IIH Logical "1" Input Current VCC = 5.5V, VIN= 2.7V (Note 4) IIL Logical "0" Input Current VCC = 5.5V, VIN = .4V (Note 4) 100 -360 uA II Input Reverse Current VCC = 5.5V, VIN = 7V (Note 4) -.01 .1 mA 1, 2, 3 VCC = 5.5V, VO = .5V (Note 4) -20 uA 1, 2, 3 2.5 IO TRI-STATE Output Current VCC = 5.5V, VO = 2.5V (Note 4) 20 uA 1, 2, 3 VIC Input Clamp Voltage VCC = 4.5V, IIN = -18mA (Note 4) -1.5 V 1, 2, 3 IOS Output Short Circuit Current VCC = 5.5V (Note 4) -150 mA 1, 2, 3 ICC Power Supply Current VCC = 5.5V, All Outputs Disabled or Active (Note 4) 80 mA 1, 2, 3 -30 AC Parameters - Propagation Delay Time The following conditions apply, unless otherwise specified. VCC = 5V, VIN = 1.3V to VO = 1.3V, V (pulse) = 0 to 3V. Symbol Parameters Conditions Notes tPLH Input to Output CL = 30 pF (Note 4) tPHL Input to Output CL = 30 pF (Note 4) tSkew Output to Output www.national.com CL = 30 pF (Note 4) 4 Min (Note 5) Subgroups Max Unit 20 nS 9 30 nS 10, 11 20 nS 9 30 nS 10, 11 6 nS 9 9 nS 10, 11 (Continued) AC Parameters - Propagation Delay Time (Continued) The following conditions apply, unless otherwise specified. VCC = 5V, VIN = 1.3V to VO = 1.3V, V (pulse) = 0 to 3V. Symbol tPLZ tPHZ tPZL tPZH Parameters Conditions Notes S2 Open, Enable, CL = 10 pF (Note 4) S2 Open, Enable, CL = 10 pF (Note 4) S1 Open, Enable, CL = 10 pF (Note 4) S1 Open, Enable, CL = 10 pF (Note 4) S2 Open, Enable, CL = 30 pF (Note 4) Min Enable to Output Enable to Output Enable to Output S2 Open, Enable, CL = 30 pF (Note 4) S1 Open, Enable, CL = 30 pF (Note 4) Enable to Output S1 Open, Enable, CL = 30 pF (Note 4) (Note 5) Subgroups Max Unit 35 nS 9 53 nS 10, 11 35 nS 9 53 nS 10, 11 30 nS 9 45 nS 10, 11 30 nS 9 45 nS 10, 11 45 nS 9 10, 11 68 nS 45 nS 9 68 nS 10, 11 40 nS 9 10, 11 60 nS 40 nS 9 60 nS 10, 11 DC Parameters - Drift Values The following conditions apply, unless otherwise specified. Delta calculations performed on QMLV only devices after burn-in and at Group B5. Symbol Parameters Conditions Notes Min Max Units Subgroups VOL Output Low Voltage VCC = 4.5, IOL = 20 mA (Note 4) -50 50 mV 1 VOH Output High Voltage VCC = 4.5, IOH = -20 mA (Note 4) -250 250 mV 1 ICC Power Supply Current VCC = 5.5, All outputs disabled or active (Note 4) -8 8 mA 1 5 www.national.com DS26LS31MQML DS26LS31M - SMD, QMLV & RH Electrical Characteristics DS26LS31MQML DS26LS31M - 883 Electrical Characteristics DC Parameters Symbol Parameters VIH Conditions Notes Min Logical "1" Input Voltage (Notes 3, 4) 2 VIL Logical "0" Input Voltage (Notes 3, 4) Unit Subgroups V 1, 2, 3 .8 V 1, 2, 3 V 1, 2, 3 .5 V 1, 2, 3 Max VOH Logical "1" Output Voltage VCC = 4.5V, IOH = -20mA (Note 4) VOL Logical "0" Output Voltage VCC = 4.5V, IOL = 20mA (Note 4) IIH Logical "1" Input Current VCC = 5.5V, VIN = 2.7V (Note 4) 20 uA 1, 2, 3 IIL Logical "0" Input Current VCC = 5.5V, VIN = .4V (Note 4) -200 uA 1, 2, 3 II Input Reverse Current VCC = 5.5V, VIN = 7V (Note 4) .1 mA 1, 2, 3 IO TRI-STATE Output Current 1, 2, 3 VIC 2.5 VCC = 5.5V, VO = .5V (Note 4) -20 uA VCC = 5.5V, VO = 2.5V (Note 4) 20 uA 1, 2, 3 Input Clamp Voltage VCC = 4.5V, IIN = -18mA (Note 4) -1.5 V 1, 2, 3 IOS (min) Output Short Circuit Current VCC = 5.5V (Note 4) mA 1, 2, 3 IOS (max) Output Short Circuit Current VCC = 5.5V (Note 4) -150 mA 1, 2, 3 Power Supply Current VCC = 5.5V, All Outputs Disabled or Active (Note 4) 60 mA 1, 2, 3 ICC -30 AC Parameters - Propagation Delay Time The following conditions apply, unless otherwise specified. VCC = 5V, CL = 50pF or equivalent impedance provided by diode load. Symbol Parameters tPLH Input to Output tPHL tSkew tPLZ tPHZ tPZL tPZH Conditions Notes Subgroups Max Unit (Notes 4, 6) 15 nS 9 30 nS 10, 11. Input to Output (Notes 4, 6) 15 nS 9 30 nS 10, 11. Output to Output (Notes 4, 6) 6 nS 9 9 nS 10, 11. S2 Open, Enable (Notes 4, 6) 35 nS 9 53 nS 10, 11. S2 Open, /Enable (Notes 4, 6) 35 nS 9 53 nS 10, 11. S1 Open, Enable (Notes 4, 6) 25 nS 9 45 nS 10, 11. S1 Open, /Enable (Notes 4, 6) 25 nS 9 45 nS 10, 11. S2 Open, Enable (Notes 4, 6) 30 nS 9 68 nS 10, 11. S2 Open, /Enable (Notes 4, 6) 30 nS 9 68 nS 10, 11. S1 Open, Enable (Notes 4, 6) 30 nS 9 60 nS 10, 11. S1 Open, /Enable (Notes 4, 6) 30 nS 9 60 nS 10, 11. Enable to Output Enable to Output Enable to Output Enable to Output www.national.com 6 Min Note 2: Derate CDip = 11.5 mW/C, CLCC = 13mW/C, Cerpack = 7.4mW/C above 25C. Note 3: Parameter tested go-no-go only. Note 4: Subgroups 1, 2 and 9, 10: Power dissipation must be externally controlled at elevated temperatures. Note 5: Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD 883, Method 1019, Condition A. Note 6: Subgroup 10 and 11 guaranteed but not tested. AC Test Circuit and Switching Time Waveforms 20141203 S1 and S2 of load circuit are closed except where shown. FIGURE 1. AC Test Circuit 20141204 f = 1 MHz, tr 15 ns, tf 6 ns FIGURE 2. Propagation Delays 20141205 f = 1 MHz, tr 15 ns, tf 6 ns FIGURE 3. Enable and Disable Times 7 www.national.com DS26LS31MQML Note 1: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. DS26LS31MQML Typical Applications Two-Wire Balanced System, RS-422 20141206 Note 7: RT is optional although highly recommended to reduce reflection. Typical Performance Characteristics DS26LS31MQMLCN Unloaded IC vs Frequency vs TA DS26LS31MQML ICC vs VCC vs TA 20141207 20141208 DS26LS31MQMLCN VOH vs IOH vs TA DS26LS31MQMLCN VOL vs IOL vs TA 20141210 20141209 www.national.com 8 DS26LS31MQML Typical Performance Characteristics (Continued) DS26LS31MQMLCN VOD vs IO vs TA 20141211 9 www.national.com DS26LS31MQML Revision History Section Date Released Revision Section Originator Changes 08/04/05 A New Release, Corporate format R. Malone 2 MDS data sheets converted into a Corp. data sheet format. Following MDS data sheets will be Archived MDDS26LS31M-X-RH, Rev.2A0, MNDS26LS31M-X, Rev. 0A0 03/01/06 B Ordering Info. Table, Absolute Ratings, Maximum Operating Conditions, New Radiation Section. Typo's in QMLV & RH, 883 AC Electrical Characteristics Parameters Column R. Malone Added: Juction temp., Thermal Resistance JA and JC. Added a Radiation Section. Changed: Maximum Operating Conditions to Recommended Operating Conditions, Enable and Disable Time to Enable to Output. Revision A will be archived. www.national.com 10 DS26LS31MQML Physical Dimensions inches (millimeters) unless otherwise noted 16 Lead Ceramic Flatpak (W) NS Package Number W16A 16 Lead Ceramic Dual-in-Line Package (J) NS Package Number J16A 11 www.national.com DS26LS31MQML Quad High Speed Differential Line Driver Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 20 Lead Ceramic Leadless Chip Carrier (E) NS Package Number E20A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated