1
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
MX25L1006E
DATASHEET
2
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Contents
FEATURES .................................................................................................................................................................. 4
GENERAL .......................................................................................................................................................... 4
PERFORMANCE ............................................................................................................................................... 4
SOFTWARE FEATURES ................................................................................................................................... 4
HARDWARE FEATURES ................................................................................................................................... 5
GENERAL DESCRIPTION .........................................................................................................................................5
PIN CONFIGURATIONS .............................................................................................................................................. 6
8-PIN SOP (150mil) ........................................................................................................................................... 6
8-LAND USON (2x3mm) ................................................................................................................................... 6
PIN DESCRIPTION ...................................................................................................................................................... 6
BLOCK DIAGRAM ....................................................................................................................................................... 7
DATA PROTECTION .................................................................................................................................................... 8
Table 1. Protected Area Sizes ............................................................................................................................ 8
HOLD FEATURE .......................................................................................................................................................... 9
Figure 1. Hold Condition Operation ................................................................................................................... 9
Table 2. COMMAND DEFINITION ................................................................................................................... 10
MEMORY ORGANIZATION ....................................................................................................................................... 11
Table 3. Memory Organization ........................................................................................................................ 11
DEVICE OPERATION ................................................................................................................................................ 12
Figure 2. Serial Modes Supported.................................................................................................................... 12
COMMAND DESCRIPTION ....................................................................................................................................... 13
(1) Write Enable (WREN) ................................................................................................................................. 13
(2) Write Disable (WRDI) .................................................................................................................................. 13
(3) Read Identication (RDID) .......................................................................................................................... 13
(4) Read Status Register (RDSR) .................................................................................................................... 14
Status Register ................................................................................................................................................. 14
(5) Write Status Register (WRSR) .................................................................................................................... 15
Table 4. Protection Modes ................................................................................................................................ 15
(6) Read Data Bytes (READ) ........................................................................................................................... 16
(7) Read Data Bytes at Higher Speed (FAST_READ) ..................................................................................... 16
(9) Sector Erase (SE) ....................................................................................................................................... 16
(10) Block Erase (BE)....................................................................................................................................... 17
(11) Chip Erase (CE) ........................................................................................................................................ 17
(12) Page Program (PP)................................................................................................................................... 17
(13) Deep Power-down (DP) ............................................................................................................................ 18
(14) Release from Deep Power-down (RDP), Read Electronic Signature (RES) ........................................... 18
(15) Read Electronic Manufacturer ID & Device ID (REMS) ............................................................................ 19
Table of ID Denitions ...................................................................................................................................... 19
(16) Read SFDP Mode (RDSFDP) ................................................................................................................... 20
Read Serial Flash Discoverable Parameter (RDSFDP) Sequence .................................................................. 20
Table a. Signature and Parameter Identication Data Values ......................................................................... 21
Table b. Parameter Table (0): JEDEC Flash Parameter Tables ....................................................................... 22
Table c. Parameter Table (1): Macronix Flash Parameter Tables ..................................................................... 24
3
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
POWER-ON STATE ...................................................................................................................................................26
ELECTRICAL SPECIFICATIONS .............................................................................................................................. 27
ABSOLUTE MAXIMUM RATINGS ................................................................................................................... 27
Figure 3. Maximum Negative Overshoot Waveform ........................................................................................ 27
CAPACITANCE TA = 25°C, f = 1.0 MHz ........................................................................................................... 27
Figure 4. Maximum Positive Overshoot Waveform .......................................................................................... 27
Figure 5. INPUT TEST WAVEFORMS AND MEASUREMENT LEVEL ............................................................ 28
Figure 6. OUTPUT LOADING ......................................................................................................................... 28
Table 5. DC CHARACTERISTICS (Temperature = -40°C to 85°C for Industrial grade, VCC = 2.7V ~ 3.6V) 29
Table 6. AC CHARACTERISTICS (Temperature = -40°C to 85°C for Industrial grade, VCC = 2.7V ~ 3.6V) 30
Table 7. Power-Up Timing ................................................................................................................................ 31
INITIAL DELIVERY STATE............................................................................................................................... 31
Timing Analysis ........................................................................................................................................................32
Figure 7. Serial Input Timing ............................................................................................................................ 32
Figure 8. Output Timing .................................................................................................................................... 32
Figure 9. Hold Timing ....................................................................................................................................... 33
Figure 10. WP# Disable Setup and Hold Timing during WRSR when SRWD=1 ............................................. 33
Figure 11. Write Enable (WREN) Sequence (Command 06) ........................................................................... 34
Figure 12. Write Disable (WRDI) Sequence (Command 04) ............................................................................ 34
Figure 13. Read Identication (RDID) Sequence (Command 9F) .................................................................... 34
Figure 14. Read Status Register (RDSR) Sequence (Command 05) .............................................................. 35
Figure 15. Write Status Register (WRSR) Sequence (Command 01) ............................................................. 35
Figure 16. Read Data Bytes (READ) Sequence (Command 03) .................................................................... 35
Figure 17. Read at Higher Speed (FAST_READ) Sequence (Command 0B) ................................................ 36
Figure 18. Dual Output Read Mode Sequence (Command 3B) ....................................................................... 36
Figure 19. Page Program (PP) Sequence (Command 02).............................................................................. 37
Figure 20. Sector Erase (SE) Sequence (Command 20) ................................................................................ 38
Figure 21. Block Erase (BE) Sequence (Command 52 or D8) ........................................................................ 38
Figure 22. Chip Erase (CE) Sequence (Command 60 or C7) ......................................................................... 39
Figure 23. Deep Power-down (DP) Sequence (Command B9)....................................................................... 39
Figure 24. Read Electronic Signature (RES) Sequence (Command AB) ........................................................ 39
Figure 25. Release from Deep Power-down (RDP) Sequence (Command AB) ............................................. 40
Figure 26. Read Electronic Manufacturer & Device ID (REMS) Sequence (Command 90)............................ 40
Figure 27. Power-up Timing ............................................................................................................................. 41
RECOMMENDED OPERATING CONDITIONS ......................................................................................................... 42
Figure 28. AC Timing at Device Power-Up ....................................................................................................... 42
Figure 29. Power-Down Sequence .................................................................................................................. 43
ERASE AND PROGRAMMING PERFORMANCE .................................................................................................... 44
DATA RETENTION .................................................................................................................................................... 44
LATCH-UP CHARACTERISTICS .............................................................................................................................. 44
ORDERING INFORMATION ...................................................................................................................................... 45
PART NAME DESCRIPTION ..................................................................................................................................... 46
PACKAGE INFORMATION ........................................................................................................................................47
REVISION HISTORY ................................................................................................................................................. 49
4
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
1M-BIT [x 1/x 2] CMOS SERIAL FLASH
FEATURES
GENERAL
• Serial Peripheral Interface compatible -- Mode 0 and Mode 3
• 1,048,576 x 1 bit structure or 524,288 x 2 bits (Dual Output mode) Structure
• 32 Equal Sectors with 4K byte each
- Any Sector can be erased individually
• 2 Equal Blocks with 64K byte each
- Any Block can be erased individually
• Single Power Supply Operation
- 2.7 to 3.6 volt for read, erase, and program operations
• Latch-up protected to 100mA from -1V to Vcc +1V
PERFORMANCE
• High Performance
- Fast access time: 104MHz serial clock
- Serial clock of Dual Output mode: 80MHz
- Fast program time: 1.4ms(typ.) and 5ms(max.)/page (256-byte per page)
- Byte program time: 9us (typ.)
- Fast erase time: 60ms(typ.)/sector (4K-byte per sector) ; 1s(typ.) and 2s(max.)/chip
• Low Power Consumption
- Low active read current: 12mA(max.) at 104MHz and 4mA(max.) at 33MHz
- Low active programming current: 20mA (max.)
- Low active sector erase current: 15mA (max.)
- Low standby current: 25uA (max.)
- Deep power-down mode 5uA (typical)
• Minimum 100,000 erase/program cycles
• 20 years data retention
SOFTWARE FEATURES
• Input Data Format
- 1-byte Command code
• Block Lock protection
- The BP0~BP1 status bit denes the size of the area to be software protected against Program and Erase in-
structions.
• Auto Erase and Auto Program Algorithm
- Automatically erases and veries data at selected sector
- Automatically programs and veries data at selected page by an internal algorithm that automatically times the
program pulse widths (Any page to be programed should have page in the erased state rst)
• Status Register Feature
• Electronic Identication
- JEDEC 2-byte Device ID
- RES command, 1-byte Device ID
• Support Serial Flash Discoverable Parameters (SFDP) mode
5
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
HARDWARE FEATURES
• SCLK Input
- Serial clock input
• SI/SIO0
- Serial Data Input or Serial Data Output for Dual output mode
• SO/SIO1
- Serial Data Output or Serial Data Output for Dual output mode
• WP# pin
- Hardware write protection
• HOLD# pin
- pause the chip without diselecting the chip
• PACKAGE
- 8-pin SOP (150mil)
- 8-USON (2x3mm)
- All devices are RoHS Compliant and Halogen-free
GENERAL DESCRIPTION
MX25L1006E is a CMOS 1,048,576 bit serial Flash memory, which is congured as 131,072 x 8 internally. MX25-
L1006E features a serial peripheral interface and software protocol allowing operation on a simple 3-wire bus. The
three bus signals are a clock input (SCLK), a serial data input (SI), and a serial data output (SO). Serial access to
the device is enabled by CS# input.
MX25L1006E provides sequential read operation on whole chip.
After program/erase command is issued, auto program/erase algorithms which program/erase and verify the speci-
ed page or sector/block locations will be executed. Program command is executed on page (256 bytes) basis, and
erase command is executes on chip or sector (4K-bytes) or block (64K-bytes).
To provide user with ease of interface, a status register is included to indicate the status of the chip. The status read
command can be issued to detect completion status of a program or erase operation via WIP bit.
When the device is not in operation and CS# is high, it is put in standby mode and draws less than 25uA DC cur-
rent.
The MX25L1006E utilizes Macronix's proprietary memory cell, which reliably stores memory contents even after
100,000 program and erase cycles.
6
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
PIN CONFIGURATIONS
SYMBOL DESCRIPTION
CS# Chip Select
SI/SIO0 Serial Data Input (for 1 x I/O)/ Serial Data
Input & Output (for Dual output mode)
SO/SIO1 Serial Data Output (for 1 x I/O)/ Serial Data
Input & Output (for Dual output mode)
SCLK Clock Input
HOLD# Hold, to pause the device without
deselecting the device
WP# Write Protection
VCC + 3.3V Power Supply
GND Ground
PIN DESCRIPTION
8-PIN SOP (150mil)
1
2
3
4
CS#
SO/SIO1
WP#
GND
VCC
HOLD#
SCLK
SI/SIO0
8
7
6
5
8-LAND USON (2x3mm)
1
2
3
4
CS#
SO/SIO1
WP#
GND
8
7
6
5
VCC
HOLD#
SCLK
SI/SIO0
7
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
BLOCK DIAGRAM
Address
Generator
Memory Array
Page Buffer
Y-Decoder
X-Decoder
Data
Register
SRAM
Buffer
SI
SCLK Clock Generator
State
Machine
Mode
Logic
Sense
Amplifier
HV
Generator
Output
Buffer
SO
CS#
8
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
DATA PROTECTION
During power transition, there may be some false system level signals which result in inadvertent erasure or
programming. The device is designed to protect itself from these accidental write cycles.
The state machine will be reset as standby mode automatically during power up. In addition, the control register
architecture of the device constrains that the memory contents can only be changed after specic command
sequences have completed successfully.
In the following, there are several features to protect the system from the accidental write cycles during VCC power-
up and power-down or from system noise.
• Valid command length checking: The command length will be checked whether it is at byte base and com-
pleted on byte boundary.
• Write Enable (WREN) command: WREN command is required to set the Write Enable Latch bit (WEL) before
other command to change data. The WEL bit will return to reset stage under following situation:
- Power-up
- Write Disable (WRDI) command completion
- Write Status Register (WRSR) command completion
- Page Program (PP) command completion
- Sector Erase (SE) command completion
- Block Erase (BE) command completion
- Chip Erase (CE) command completion
• Software Protection Mode (SPM): by using BP0-BP1 bits to set the part of Flash protected from data change.
• Hardware Protection Mode (HPM): by using WP# going low to protect the BP0-BP1 bits and SRWD bit from
data change.
• Deep Power Down Mode: By entering deep power down mode, the ash device also is under protected from
writing all commands except Release from deep power down mode command (RDP) and Read Electronic Sig-
nature command (RES).
Table 1. Protected Area Sizes
Status bit Protect level 1Mb
BP1 BP0
0 0 0 (none) None
0 1 1 (1 block) Block 1
1 0 2 (2 blocks) All
1 1 3 (All) All
9
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
HOLD FEATURE
HOLD# pin signal goes low to hold any serial communications with the device. The HOLD feature will not stop the
operation of write status register, programming, or erasing in progress.
The operation of HOLD requires Chip Select(CS#) keeping low and starts on falling edge of HOLD# pin signal
while Serial Clock (SCLK) signal is being low (if Serial Clock signal is not being low, HOLD operation will not start
until Serial Clock signal being low). The HOLD condition ends on the rising edge of HOLD# pin signal while Se-
rial Clock(SCLK) signal is being low (if Serial Clock signal is not being low, HOLD operation will not end until Serial
Clock being low), see Figure 1.
The Serial Data Output (SO) is high impedance, both Serial Data Input (SI) and Serial Clock (SCLK) are don't care
during the HOLD operation. If Chip Select (CS#) drives high during HOLD operation, it will reset the internal logic of
the device. To re-start communication with chip, the HOLD# must be at high and CS# must be at low.
HOLD#
CS#
SCLK
Hold
Condition
(standard)
Hold
Condition
(non-standard)
Figure 1. Hold Condition Operation
10
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Table 2. COMMAND DEFINITION
(1) ADD=00H will output the manufacturer's ID rst and ADD=01H will output device ID rst.
(2) It is not allowed to adopt any other code which is not in the above command denition table.
COMMAND
(byte)
WREN
(write enable)
WRDI
(write disable)
RDID
(read
identication)
RDSR
(read status
register)
WRSR (write
status register)
READ
(read data)
1st 06 (hex) 04 (hex) 9F (hex) 05 (hex) 01 (hex) 03 (hex)
2nd AD1
3rd AD2
4th AD3
5th
Action
sets the (WEL)
write enable
latch bit
resets the (WEL)
write enable
latch bit
outputs
manufacturer
ID and 2-byte
device ID
to read out the
status register
to write new
values to the
status register
n bytes read out
until CS# goes
high
COMMAND
(byte)
Fast Read
(fast read data)
RDSFDP
(Read SFDP)
DREAD
(Dual Output
mode)
SE
(Sector Erase)
BE
(Block Erase)
CE
(Chip Erase)
1st 0B (hex) 5A (hex) 3B (hex) 20 (hex) 52 or D8 (hex) 60 or C7 (hex)
2nd AD1 AD1 AD1 AD1 AD1
3rd AD2 AD2 AD2 AD2 AD2
4th AD3 AD3 AD3 AD3 AD3
5th Dummy Dummy
Action
n bytes read out
until CS# goes
high
Read SFDP
mode
n bytes read out
until CS# goes
high
to erase the
selected sector
to erase the
selected block
to erase the
whole chip
COMMAND
(byte)
PP
(Page
Program)
DP
(Deep Power
Down)
RDP
(Release from
Deep Power-
down)
RES
(Read
Electronic ID)
REMS
(Read
Electronic
Manufacturer &
Device ID)
1st 02 (hex) B9 (hex) AB (hex) AB (hex) 90 (hex)
2nd AD1 x x
3rd AD2 x x
4th AD3 x ADD(1)
5th
Action
to program the
selected page
enters deep
power down
mode
release from
deep power
down mode
to read out
1-byte Device
ID
Output the
manufacturer ID
and device ID
11
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Table 3. Memory Organization
Block Sector Address Range
1
31 01F000h 01FFFFh
:::
16 010000h 010FFFh
0
15 00F000h 00FFFFh
:::
3 003000h 003FFFh
2 002000h 002FFFh
1 001000h 001FFFh
0 000000h 000FFFh
MEMORY ORGANIZATION
12
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
DEVICE OPERATION
1. Before a command is issued, status register should be checked to ensure the device is ready for the intended
operation.
2. When incorrect command is inputted to this LSI, this LSI becomes standby mode and keeps the standby mode
until next CS# falling edge. In standby mode, SO pin of this LSI should be High-Z. The CS# falling time needs to
follow tCHCL spec. (Please refer to Table 6. AC CHARACTERISTICS)
3. When correct command is inputted to this LSI, this LSI becomes active mode and keeps the active mode until
next CS# rising edge. The CS# rising time needs to follow tCLCH spec. (Please refer to Table 6. AC CHARAC-
TERISTICS)
4. Input data is latched on the rising edge of Serial Clock(SCLK) and data shifts out on the falling edge of SCLK.
The difference of Serial mode 0 and mode 3 is shown as Figure 2.
Figure 2. Serial Modes Supported
SCLK
MSB
CPHA shift in shift out
SI
0
1
CPOL
0(Serial mode 0)
(Serial mode 3) 1
SO
SCLK
MSB
5. For the following instructions: RDID, RDSR, READ, FAST_READ, RDSFDP, DREAD, RES and REMS the shift-
ed-in instruction sequence is followed by a data-out sequence. After any bit of data being shifted out, the CS#
can be high. For the following instructions: WREN, WRDI, WRSR, SE, BE, CE, PP, RDP and DP the CS# must
go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
6. During the progress of Write Status Register, Program, Erase operation, to access the memory array is neglect-
ed and not affect the current operation of Write Status Register, Program, and Erase.
Note:
CPOL indicates clock polarity of Serial master:
-CPOL=1 for SCLK high while idle,
-CPOL=0 for SCLK low while not transmitting.
CPHA indicates clock phase.
The combination of CPOL bit and CPHA bit decides which Serial mode is supported.
13
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
COMMAND DESCRIPTION
(1) Write Enable (WREN)
The Write Enable (WREN) instruction is for setting Write Enable Latch (WEL) bit. For those instructions like PP, SE,
BE, CE, and WRSR, which are intended to change the device content, should be set every time after the WREN in-
struction setting the WEL bit.
The sequence of issuing WREN instruction is: CS# goes low→ sending WREN instruction code→ CS# goes high. (see
Figure 11)
(2) Write Disable (WRDI)
The Write Disable (WRDI) instruction is for resetting Write Enable Latch (WEL) bit.
The sequence of issuing WRDI instruction is: CS# goes low→ sending WRDI instruction code→ CS# goes high. (see
Figure 12)
The WEL bit is reset by following situations:
- Power-up
- Write Disable (WRDI) instruction completion
- Write Status Register (WRSR) instruction completion
- Page Program (PP) instruction completion
- Sector Erase (SE) instruction completion
- Block Erase (BE) instruction completion
- Chip Erase (CE) instruction completion
(3) Read Identication (RDID)
RDID instruction is for reading the manufacturer ID of 1-byte and followed by Device ID of 2-byte. The Macronix
Manufacturer ID is C2(hex), the memory type ID is 20(hex) as the rst-byte device ID, and the individual device ID
of second-byte ID is as followings: 11(hex) for MX25L1006E.
The sequence of issuing RDID instruction is: CS# goes low→sending RDID instruction code→24-bits ID data out on
SO→to end RDID operation can use CS# to high at any time during data out. (see Figure. 13)
While Program/Erase operation is in progress, it will not decode the RDID instruction, so there's no effect on the cy-
cle of program/erase operation which is currently in progress. When CS# goes high, the device is at standby stage.
14
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
(4) Read Status Register (RDSR)
The RDSR instruction is for reading Status Register Bits. The Read Status Register can be read at any time (even in
program/erase/write status register condition) and continuously. It is recommended to check the Write in Progress (WIP)
bit before sending a new instruction when a program, erase, or write status register operation is in progress.
The sequence of issuing RDSR instruction is: CS# goes low→sending RDSR instruction code→Status Register
data out on SO (see Figure. 14)
The denition of the status register bits is as below:
WIP bit. The Write in Progress (WIP) bit, a volatile bit, indicates whether the device is busy in program/erase/write
status register progress. When WIP bit sets to 1, which means the device is busy in program/erase/write status
register progress. When WIP bit sets to 0, which means the device is not in progress of program/erase/write status
register cycle.
WEL bit. The Write Enable Latch (WEL) bit, a volatile bit, indicates whether the device is set to internal write enable
latch. When WEL bit sets to 1, which means the internal write enable latch is set, the device can accept program/
erase/write status register instruction. When WEL bit sets to 0, which means no internal write enable latch; the de-
vice will not accept program/erase/write status register instruction.
BP1, BP0 bits. The Block Protect (BP1, BP0) bits, non-volatile bits, indicate the protected area (as dened in table
1) of the device to against the program/erase instruction without hardware protection mode being set. To write the
Block Protect (BP1, BP0) bits requires the Write Status Register (WRSR) instruction to be executed. Those bits
dene the protected area of the memory to against Page Program (PP), Sector Erase (SE), Block Erase (BE) and
Chip Erase(CE) instructions (only if all Block Protect bits set to 0, the CE instruction can be executed)
SRWD bit. The Status Register Write Disable (SRWD) bit, non-volatile bit, is operated together with Write Protec-
tion (WP#) pin for providing hardware protection mode. The hardware protection mode requires SRWD sets to 1
and WP# pin signal is low stage. In the hardware protection mode, the Write Status Register (WRSR) instruction is
no longer accepted for execution and the SRWD bit and Block Protect bits (BP1, BP0) are read only.
Notes: 1. See the table "Protected Area Sizes".
bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
SRWD (status
register write
protect)
000
BP1
(level of
protected
block)
BP0
(level of
protected
block)
WEL
(write enable
latch)
WIP
(write in
progress bit)
1=status
register write
disable
(Note 1) (Note 1)
1=write
enable
0=not write
enable
1=write
operation
0=not in write
operation
Status Register
15
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
(5) Write Status Register (WRSR)
The WRSR instruction is for changing the values of Status Register Bits. Before sending WRSR instruction, the
Write Enable (WREN) instruction must be decoded and executed to set the Write Enable Latch (WEL) bit in ad-
vance. The WRSR instruction can change the value of Block Protect (BP1, BP0) bits to dene the protected area
of memory (as shown in table 1). The WRSR also can set or reset the Status Register Write Disable (SRWD) bit in
accordance with Write Protection (WP#) pin signal. The WRSR instruction cannot be executed once the Hardware
Protected Mode (HPM) is entered.
The sequence of issuing WRSR instruction is: CS# goes low→ sending WRSR instruction code→ Status Register
data on SI→ CS# goes high. (see Figure 15)
The WRSR instruction has no effect on b6, b5, b4, b1, b0 of the status register.
The CS# must go high exactly at the byte boundary; otherwise, the instruction will be rejected and not executed.
The self-timed Write Status Register cycle time (tW) is initiated as soon as Chip Select (CS#) goes high. The Write
in Progress (WIP) bit still can be check out during the Write Status Register cycle is in progress. The WIP sets 1
during the tW timing, and sets 0 when Write Status Register Cycle is completed, and the Write Enable Latch (WEL)
bit is reset.
Table 4. Protection Modes
Note:
1. As dened by the values in the Block Protect (BP1, BP0) bits of the Status Register, as shown in Table 1.
As the table above showing, the summary of the Software Protected Mode (SPM) and Hardware Protected Mode (HPM).
Software Protected Mode (SPM):
- When SRWD bit=0, no matter WP# is low or high, the WREN instruction may set the WEL bit and can
change the values of SRWD, BP1, BP0. The protected area, which is dened by BP1, BP0, is at software
protected mode (SPM).
- When SRWD bit=1 and WP# is high, the WREN instruction may set the WEL bit can change the values of
SRWD, BP1, BP0. The protected area, which is dened by BP1, BP0, is at software protected mode (SPM)
Note: If SRWD bit=1 but WP# is low, it is impossible to write the Status Register even if the WEL bit has
previously been set. It is rejected to write the Status Register and not be executed.
Hardware Protected Mode (HPM):
- When SRWD bit=1, and then WP# is low (or WP# is low before SRWD bit=1), it enters the hardware pro-
tected mode (HPM). The data of the protected area is protected by software protected mode by BP1, BP0
and hardware protected mode by the WP# to against data modication.
Note: to exit the hardware protected mode requires WP# driving high once the hardware protected mode is
entered. If the WP# pin is permanently connected to high, the hardware protected mode can never be
entered; only can use software protected mode via BP1, BP0.
Mode Status register condition WP# and SRWD bit status Memory
Software protection
mode (SPM)
Status register can be written
in (WEL bit is set to "1") and
the SRWD, BP0-BP1
bits can be changed
WP#=1 and SRWD bit=0, or
WP#=0 and SRWD bit=0, or
WP#=1 and SRWD=1
The protected area
cannot
be program or erase.
Hardware protection
mode (HPM)
The SRWD, BP0-BP1 of
status register bits cannot be
changed
WP#=0, SRWD bit=1
The protected area
cannot
be program or erase.
16
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
(6) Read Data Bytes (READ)
The read instruction is for reading data out. The address is latched on rising edge of SCLK, and data shifts out on
the falling edge of SCLK at a maximum frequency fR. The rst address byte can be at any location. The address
is automatically increased to the next higher address after each byte data is shifted out, so the whole memory can
be read out at a single READ instruction. The address counter rolls over to 0 when the highest address has been
reached.
The sequence of issuing READ instruction is: CS# goes low→ sending READ instruction code→ 3-byte address on
SI→ data out on SO→ to end READ operation can use CS# to high at any time during data out. (see Figure. 16)
(7) Read Data Bytes at Higher Speed (FAST_READ)
The FAST_READ instruction is for quickly reading data out. The address is latched on rising edge of SCLK, and
data of each bit shifts out on the falling edge of SCLK at a maximum frequency fC. The rst address byte can be at
any location. The address is automatically increased to the next higher address after each byte data is shifted out,
so the whole memory can be read out at a single FAST_READ instruction. The address counter rolls over to 0 when
the highest address has been reached.
The sequence of issuing FAST_READ instruction is: CS# goes low→ sending FAST_READ instruction code→
3-byte address on SI→ 1-dummy byte address on SI→data out on SO→ to end FAST_READ operation can use
CS# to high at any time during data out. (see Figure. 17)
While Program/Erase/Write Status Register cycle is in progress, FAST_READ instruction is rejected without any im-
pact on the Program/Erase/Write Status Register current cycle.
(8) Dual Output Mode (DREAD)
The DREAD instruction enables double throughput of Serial Flash in read mode. The address is latched on rising
edge of SCLK, and data of every two bits(interleave on 1I/2O pins) shift out on the falling edge of SCLK at a maxi-
mum frequency fT. The rst address byte can be at any location. The address is automatically increased to the next
higher address after each byte data is shifted out, so the whole memory can be read out at a single DREAD instruc-
tion. The address counter rolls over to 0 when the highest address has been reached. Once writing DREAD instruc-
tion, the following data out will perform as 2-bit instead of previous 1-bit.
The sequence is shown as Figure 18.
While Program/Erase/Write Status Register cycle is in progress, DREAD instruction is rejected without any impact
on the Program/Erase/Write Status Register current cycle.
The DREAD only performs read operation. Program/Erase /Read ID/Read status....operation do not support DREAD
throughputs.
(9) Sector Erase (SE)
The Sector Erase (SE) instruction is for erasing the data of the chosen sector to be "1". A Write Enable (WREN) in-
struction must execute to set the Write Enable Latch (WEL) bit before sending the Sector Erase (SE). Any address
of the sector (see table 3) is a valid address for Sector Erase (SE) instruction. The CS# must go high exactly at the
byte boundary (the latest eighth of address byte been latched-in); otherwise, the instruction will be rejected and not
executed.
17
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Address bits [Am-A12] (Am is the most signicant address) select the sector address.
The sequence of issuing SE instruction is: CS# goes low → sending SE instruction code→ 3-byte address on SI →
CS# goes high. (see Figure 20)
The self-timed Sector Erase Cycle time (tSE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Sector Erase cycle is in progress. The WIP sets 1 during the
tSE timing, and sets 0 when Sector Erase Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the
page is protected by BP1, BP0 bits, the Sector Erase (SE) instruction will not be executed on the page.
(10) Block Erase (BE)
The Block Erase (BE) instruction is for erasing the data of the chosen block to be "1". A Write Enable (WREN) in-
struction must be executed to set the Write Enable Latch (WEL) bit before sending the Block Erase (BE). Any ad-
dress of the block (see table 3) is a valid address for Block Erase (BE) instruction. The CS# must go high exactly
at the byte boundary (the latest eighth of address byte been latched-in); otherwise, the instruction will be rejected
and not executed.
The sequence of issuing BE instruction is: CS# goes low → sending BE instruction code→ 3-byte address on SI →
CS# goes high. (see Figure 21)
The self-timed Block Erase Cycle time (tBE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Sector Erase cycle is in progress. The WIP sets 1 during the
tBE timing, and sets 0 when Sector Erase Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the
page is protected by BP1, BP0 bits, the Block Erase (BE) instruction will not be executed on the page.
(11) Chip Erase (CE)
The Chip Erase (CE) instruction is for erasing the data of the whole chip to be "1". A Write Enable (WREN) instruc-
tion must execute to set the Write Enable Latch (WEL) bit before sending the Chip Erase (CE). Any address of the
sector (see table 3) is a valid address for Chip Erase (CE) instruction. The CS# must go high exactly at the byte
boundary (the latest eighth of address byte been latched-in); otherwise, the instruction will be rejected and not ex-
ecuted.
The sequence of issuing CE instruction is: CS# goes low→ sending CE instruction code→ CS# goes high. (see
Figure 22)
The self-timed Chip Erase Cycle time (tCE) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Chip Erase cycle is in progress. The WIP sets 1 during the tCE
timing, and sets 0 when Chip Erase Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the chip
is protected by BP1, BP0 bits, the Chip Erase (CE) instruction will not be executed. It will be only executed when
BP1, BP0 all set to "0".
(12) Page Program (PP)
The Page Program (PP) instruction is for programming the memory to be "0". A Write Enable (WREN) instruction
must be executed to set the Write Enable Latch (WEL) bit before sending the Page Program (PP). The last address
byte (the 8 least signicant address bits, A7-A0) should be set to 0 for 256 bytes page program. If A7-A0 are not
all zero, transmitted data that exceed page length are programmed from the starting address (24-bit address that
last 8 bit are all 0) of currently selected page. The CS# must keep during the whole Page Program cycle. The CS#
must go high exactly at the byte boundary (the latest eighth of address byte been latched-in); otherwise, the instruc-
18
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
tion will be rejected and not executed. If the data bytes sent to the device exceeds 256, the last 256 data byte is
programmed at the request page and previous data will be disregarded. If the data bytes sent to the device has not
exceeded 256, the data will be programmed at the request address of the page. There will be no effort on the other
data bytes of the same page.
The sequence of issuing PP instruction is: CS# goes low→ sending PP instruction code→ 3-byte address on SI→ at
least 1-byte on data on SI→ CS# goes high. (see Figure 19)
The self-timed Page Program Cycle time (tPP) is initiated as soon as Chip Select (CS#) goes high. The Write in
Progress (WIP) bit still can be check out during the Page Program cycle is in progress. The WIP sets 1 during the
tPP timing, and sets 0 when Page Program Cycle is completed, and the Write Enable Latch (WEL) bit is reset. If the
page is protected by BP1, BP0 bits, the Page Program (PP) instruction will not be executed.
(13) Deep Power-down (DP)
The Deep Power-down (DP) instruction is for setting the device on the minimizing the power consumption (to enter-
ing the Deep Power-down mode), the standby current is reduced from ISB1 to ISB2). The Deep Power-down mode
requires the Deep Power-down (DP) instruction to enter, during the Deep Power-down mode, the device is not ac-
tive and all Write/Program/Erase instruction are ignored. When CS# goes high, it's only in standby mode not deep
power-down mode. It's different from Standby mode.
The sequence of issuing DP instruction is: CS# goes low→ sending DP instruction code→ CS# goes high. (see Fig-
ure 22)
Once the DP instruction is set, all instruction will be ignored except the Release from Deep Power-down mode (RDP)
and Read Electronic Signature (RES) instruction. (RES instruction to allow the ID been read out). When Power-
down, the deep power-down mode automatically stops, and when power-up, the device automatically is in standby
mode. For RDP instruction the CS# must go high exactly at the byte boundary (the latest eighth bit of instruction
code been latched-in); otherwise, the instruction will not executed. As soon as Chip Select (CS#) goes high, a delay
of tDP is required before entering the Deep Power-down mode and reducing the current to ISB2.
(14) Release from Deep Power-down (RDP), Read Electronic Signature (RES)
The Release from Deep Power-down (RDP) instruction is terminated by driving Chip Select (CS#) High. When Chip
Select (CS#) is driven High, the device is put in the Stand-by Power mode. If the device was not previously in the
Deep Power-down mode, the transition to the Stand-by Power mode is immediate. If the device was previously in
the Deep Power-down mode, though, the transition to the Stand-by Power mode is delayed by tRES2, and Chip
Select (CS#) must remain High for at least tRES2(max), as specied in Table 6. Once in the Stand-by Power mode,
the device waits to be selected, so that it can receive, decode and execute instructions.
RES instruction is for reading out the old style of 8-bit Electronic Signature, whose values are shown as table of ID
Denitions. This is not the same as RDID instruction. It is not recommended to use for new design. For new design,
please use RDID instruction. Even in Deep power-down mode, the RDP and RES are also allowed to be executed,
only except the device is in progress of program/erase/write cycle; there's no effect on the current program/erase/
write cycle in progress.
The sequence is shown as Figure 24 and Figure 25.
19
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Table of ID Denitions
RDID Command manufacturer ID memory type memory density
C2 20 11
RES Command electronic ID
10
REMS Command manufacturer ID device ID
C2 10
The RES instruction is ended by CS# going high after the ID has been read out at least once. The ID outputs re-
peatedly if continuously send the additional clock cycles on SCLK while CS# is at low. If the device was not previ-
ously in Deep Power-down mode, the device transition to standby mode is immediate. If the device was previously
in Deep Power-down mode, there's a delay of tRES2 to transit to standby mode, and CS# must remain to high at
least tRES2(max). Once in the standby mode, the device waits to be selected, so it can be receive, decode, and
execute instruction.
The RDP instruction is for releasing from Deep Power-Down Mode.
(15) Read Electronic Manufacturer ID & Device ID (REMS)
The REMS instruction is an alternative to the Release from Deep Power-down/Device ID instruction that provides
both the JEDEC assigned manufacturer ID and the specic device ID.
The REMS instruction is very similar to the Release from Deep Power-down/Device ID instruction. The instruction is
initiated by driving the CS# pin low and shift the instruction code "90h" followed by two dummy bytes and one bytes
address (A7~A0). After that, the Manufacturer ID for Macronix (C2h) and the Device ID are shifted out on the falling
edge of SCLK with most signicant bit (MSB) rst as shown in Figure 26. The Device ID values are listed in Table of
ID Denitions. If the one-byte address is initially set to 01h, the device ID will be read rst and then followed by the
Manufacturer ID. The Manufacturer and Device IDs can be read continuously, alternating from one to the other. The
instruction is completed by driving CS# high.
20
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
(16) Read SFDP Mode (RDSFDP)
The Serial Flash Discoverable Parameter (SFDP) standard provides a consistent method of describing the functional
and feature capabilities of serial ash devices in a standard set of internal parameter tables. These parameter tables
can be interrogated by host system software to enable adjustments needed to accommodate divergent features
from multiple vendors. The concept is similar to the one found in the Introduction of JEDEC Standard, JESD68 on
CFI.
The sequence of issuing RDSFDP instruction is CS# goes low→send RDSFDP instruction (5Ah)→send 3 address
bytes on SI pin→send 1 dummy byte on SI pin→read SFDP code on SO→to end RDSFDP operation can use CS#
to high at any time during data out.
SFDP is a JEDEC Standard, JESD216.
Read Serial Flash Discoverable Parameter (RDSFDP) Sequence
23
21 3456789 10 28 29 30 31
22 21 3210
High-Z
24 BIT ADDRESS
0
32 33 34 36 37 38 39 40 41 42 43 44 45 46
765432 0
1
DATA OUT 1
Dummy Cycle
MSB
76543210
DATA OUT 2
MSB MSB
7
47
765432 0
1
35
SCLK
SI
CS#
SO
SCLK
SI
CS#
SO
5Ah
Command
21
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Table a. Signature and Parameter Identication Data Values
Description Comment Add (h)
(Byte)
DW Add
(Bit)
Data (h/b)
(Note1)
Data
(h)
SFDP Signature Fixed: 50444653h
00h 07:00 53h 53h
01h 15:08 46h 46h
02h 23:16 44h 44h
03h 31:24 50h 50h
SFDP Minor Revision Number Start from 00h 04h 07:00 00h 00h
SFDP Major Revision Number Start from 01h 05h 15:08 01h 01h
Number of Parameter Headers This number is 0-based. Therefore,
0 indicates 1 parameter header. 06h 23:16 01h 01h
Unused 07h 31:24 FFh FFh
ID number (JEDEC) 00h: it indicates a JEDEC specied
header. 08h 07:00 00h 00h
Parameter Table Minor Revision
Number Start from 00h 09h 15:08 00h 00h
Parameter Table Major Revision
Number Start from 01h 0Ah 23:16 01h 01h
Parameter Table Length
(in double word)
How many DWORDs in the
Parameter table 0Bh 31:24 09h 09h
Parameter Table Pointer (PTP) First address of JEDEC Flash
Parameter table
0Ch 07:00 30h 30h
0Dh 15:08 00h 00h
0Eh 23:16 00h 00h
Unused 0Fh 31:24 FFh FFh
ID number
(Macronix manufacturer ID)
it indicates Macronix manufacturer
ID 10h 07:00 C2h C2h
Parameter Table Minor Revision
Number Start from 00h 11h 15:08 00h 00h
Parameter Table Major Revision
Number Start from 01h 12h 23:16 01h 01h
Parameter Table Length
(in double word)
How many DWORDs in the
Parameter table 13h 31:24 04h 04h
Parameter Table Pointer (PTP) First address of Macronix Flash
Parameter table
14h 07:00 60h 60h
15h 15:08 00h 00h
16h 23:16 00h 00h
Unused 17h 31:24 FFh FFh
22
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Table b. Parameter Table (0): JEDEC Flash Parameter Tables
Description Comment Add (h)
(Byte)
DW Add
(Bit)
Data (h/b)
(Note1)
Data
(h)
Block/Sector Erase sizes
00: Reserved, 01: 4KB erase,
10: Reserved,
11: not support 4KB erase
30h
01:00 01b
E5h
Write Granularity 0: 1Byte, 1: 64Byte or larger 02 1b
Write Enable Instruction Required
for Writing to Volatile Status
Registers
0: not required
1: required 00h to be written to the
status register
03 0b
Write Enable Opcode Select for
Writing to Volatile Status Registers
0: use 50h opcode,
1: use 06h opcode
Note: If target ash status register is
nonvolatile, then bits 3 and 4 must
be set to 00b.
04 0b
Unused Contains 111b and can never be
changed 07:05 111b
4KB Erase Opcode 31h 15:08 20h 20h
(1-1-2) Fast Read (Note2) 0=not support 1=support
32h
16 1b
81h
Address Bytes Number used in
addressing ash array
00: 3Byte only, 01: 3 or 4Byte,
10: 4Byte only, 11: Reserved 18:17 00b
Double Transfer Rate (DTR)
Clocking 0=not support 1=support 19 0b
(1-2-2) Fast Read 0=not support 1=support 20 0b
(1-4-4) Fast Read 0=not support 1=support 21 0b
(1-1-4) Fast Read 0=not support 1=support 22 0b
Unused 23 1b
Unused 33h 31:24 FFh FFh
Flash Memory Density 37h:34h 31:00 000F FFFFh
(1-4-4) Fast Read Number of Wait
states (Note3)
0 0000b: Wait states (Dummy
Clocks) not support 38h
04:00 0 0000b
00h
(1-4-4) Fast Read Number of
Mode Bits (Note4) 000b: Mode Bits not support 07:05 000b
(1-4-4) Fast Read Opcode 39h 15:08 FFh FFh
(1-1-4) Fast Read Number of Wait
states
0 0000b: Wait states (Dummy
Clocks) not support 3Ah
20:16 0 0000b
00h
(1-1-4) Fast Read Number of
Mode Bits 000b: Mode Bits not support 23:21 000b
(1-1-4) Fast Read Opcode 3Bh 31:24 FFh FFh
23
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Description Comment Add (h)
(Byte)
DW Add
(Bit)
Data (h/b)
(Note1)
Data
(h)
(1-1-2) Fast Read Number of Wait
states
0 0000b: Wait states (Dummy
Clocks) not support 3Ch
04:00 0 1000b
08h
(1-1-2) Fast Read Number of
Mode Bits 000b: Mode Bits not support 07:05 000b
(1-1-2) Fast Read Opcode 3Dh 15:08 3Bh 3Bh
(1-2-2) Fast Read Number of Wait
states
0 0000b: Wait states (Dummy
Clocks) not support 3Eh
20:16 0 0000b
00h
(1-2-2) Fast Read Number of
Mode Bits 000b: Mode Bits not support 23:21 000b
(1-2-2) Fast Read Opcode 3Fh 31:24 FFh FFh
(2-2-2) Fast Read 0=not support 1=support
40h
00 0b
EEh
Unused 03:01 111b
(4-4-4) Fast Read 0=not support 1=support 04 0b
Unused 07:05 111b
Unused 43h:41h 31:08 FFh FFh
Unused 45h:44h 15:00 FFh FFh
(2-2-2) Fast Read Number of Wait
states
0 0000b: Wait states (Dummy
Clocks) not support 46h
20:16 0 000b
00h
(2-2-2) Fast Read Number of
Mode Bits 000b: Mode Bits not support 23:21 000b
(2-2-2) Fast Read Opcode 47h 31:24 FFh FFh
Unused 49h:48h 15:00 FFh FFh
(4-4-4) Fast Read Number of Wait
states
0 0000b: Wait states (Dummy
Clocks) not support 4Ah
20:16 0 0000b
00h
(4-4-4) Fast Read Number of
Mode Bits 000b: Mode Bits not support 23:21 000b
(4-4-4) Fast Read Opcode 4Bh 31:24 FFh FFh
Sector Type 1 Size Sector/block size = 2^N bytes (Note5)
0x00b: this sector type doesn't exist 4Ch 07:00 0Ch 0Ch
Sector Type 1 erase Opcode 4Dh 15:08 20h 20h
Sector Type 2 Size Sector/block size = 2^N bytes
0x00b: this sector type doesn't exist 4Eh 23:16 10h 10h
Sector Type 2 erase Opcode 4Fh 31:24 D8h D8h
Sector Type 3 Size Sector/block size = 2^N bytes
0x00b: this sector type doesn't exist 50h 07:00 00h 00h
Sector Type 3 erase Opcode 51h 15:08 FFh FFh
Sector Type 4 Size Sector/block size = 2^N bytes
0x00b: this sector type doesn't exist 52h 23:16 00h 00h
Sector Type 4 erase Opcode 53h 31:24 FFh FFh
24
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Table c. Parameter Table (1): Macronix Flash Parameter Tables
Description Comment Add (h)
(Byte)
DW Add
(Bit)
Data (h/b)
(Note1)
Data
(h)
Vcc Supply Maximum Voltage
2000h=2.000V
2700h=2.700V
3600h=3.600V
61h:60h 07:00
15:08
00h
36h
00h
36h
Vcc Supply Minimum Voltage
1650h=1.650V
2250h=2.250V
2350h=2.350V
2700h=2.700V
63h:62h 23:16
31:24
00h
27h
00h
27h
H/W Reset# pin 0=not support 1=support
65h:64h
00 0b
4FF6h
H/W Hold# pin 0=not support 1=support 01 1b
Deep Power Down Mode 0=not support 1=support 02 1b
S/W Reset 0=not support 1=support 03 0b
S/W Reset Opcode Reset Enable (66h) should be issued
before Reset Opcode 11:04 1111 1111b
(FFh)
Program Suspend/Resume 0=not support 1=support 12 0b
Erase Suspend/Resume 0=not support 1=support 13 0b
Unused 14 1b
Wrap-Around Read mode 0=not support 1=support 15 0b
Wrap-Around Read mode Opcode 66h 23:16 FFh FFh
Wrap-Around Read data length
08h:support 8B wrap-around read
16h:8B&16B
32h:8B&16B&32B
64h:8B&16B&32B&64B
67h 31:24 FFh FFh
Individual block lock 0=not support 1=support
6Bh:68h
00 0b
C7FEh
Individual block lock bit
(Volatile/Nonvolatile) 0=Volatile 1=Nonvolatile 01 1b
Individual block lock Opcode 09:02 1111 1111b
Individual block lock Volatile
protect bit default protect status 0=protect 1=unprotect 10 1b
Secured OTP 0=not support 1=support 11 0b
Read Lock 0=not support 1=support 12 0b
Permanent Lock 0=not support 1=support 13 0b
Unused 15:14 11b
Unused 31:16 0xFFh 0xFFh
Unused 6Fh:6Ch 31:00 0xFFh 0xFFh
25
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Note 1: h/b is hexadecimal or binary.
Note 2: (x-y-z) means I/O mode nomenclature used to indicate the number of active pins used for the opcode (x),
address (y), and data (z). At the present time, the only valid Read SFDP instruction modes are: (1-1-1), (2-2-2),
and (4-4-4)
Note 3: Wait States is required dummy clock cycles after the address bits or optional mode bits.
Note 4: Mode Bits is optional control bits that follow the address bits. These bits are driven by the system controller
if they are specied. (eg,read performance enhance toggling bits)
Note 5: 4KB=2^0Ch,32KB=2^0Fh,64KB=2^10h
Note 6: All unused and undened area data is blank FFh.
26
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
POWER-ON STATE
The device is at below states when power-up:
- Standby mode (please note it is not deep power-down mode)
- Write Enable Latch (WEL) bit is reset
The device must not be selected during power-up and power-down stage unless the VCC achieves below correct
level:
- VCC minimum at power-up stage and then after a delay of tVSL (Refer to Table 7. Power-Up Timing)
- GND at power-down
Please note that a pull-up resistor on CS# may ensure a safe and proper power-up/down level.
An internal power-on reset (POR) circuit may protect the device from data corruption and inadvertent data change
during power up state.
For further protection on the device, if the VCC does not reach the VCC minimum level, the correct operation is not
guaranteed. The read, write, erase, and program command should be sent after the time delay: tVSL after VCC
reached VCC minimum level.
The device can accept read command after VCC reached VCC minimum and a time delay of tVSL.
Please refer to the gure of "power-up timing".
Note:
- To stabilize the VCC level, the VCC rail decoupled by a suitable capacitor close to package pins is recommend-
ed.(generally around 0.1uF)
27
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
NOTICE:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the
device. This is stress rating only and functional operational sections of this specication is not implied. Expo-
sure to absolute maximum rating conditions for extended period may affect reliability.
2. Specications contained within the following tables are subject to change.
3. During voltage transitions, all pins may overshoot to 4.6V or -0.5V for period up to 20ns.
4. All input and output pins may overshoot to VCC+0.5V while VCC+0.5V is smaller than or equal to 4.6V.
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL SPECIFICATIONS
CAPACITANCE TA = 25°C, f = 1.0 MHz
Figure 3. Maximum Negative Overshoot Waveform Figure 4. Maximum Positive Overshoot Waveform
RATING VALUE
Ambient Operating Temperature Industrial grade -40°C to 85°C
Storage Temperature -65°C to 150°C
Applied Input Voltage -0.5V to 4.6V
Applied Output Voltage -0.5V to 4.6V
VCC to Ground Potential -0.5V to 4.6V
Symbol Parameter Min. Typ. Max. Unit Conditions
CIN Input Capacitance 6 pF VIN = 0V
COUT Output Capacitance 8 pF VOUT = 0V
0V
-0.5V
20ns
4.6V
3.6V
20ns
28
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 5. INPUT TEST WAVEFORMS AND MEASUREMENT LEVEL
AC
Measurement
Level
Input timing reference level Output timing reference level
0.8VCC 0.7VCC
0.3VCC
0.5VCC
0.2VCC
Note: Input pulse rise and fall time are <5ns
Figure 6. OUTPUT LOADING
DEVICE UNDER
TEST
DIODES=IN3064
OR EQUIVALENT
CL 6.2K ohm
2.7K ohm
+3.3V
CL=30pF Including jig capacitance
29
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Symbol Parameter Notes Min. Typ. Max. Units Test Conditions
ILI Input Load Current 1 ± 2 uA VCC = VCC Max
VIN = VCC or GND
ILO Output Leakage Current 1 ± 2 uA VCC = VCC Max
VOUT = VCC or GND
ISB1 VCC Standby Current 1 25 uA VIN = VCC or GND
CS#=VCC
ISB2 Deep Power-down
Current 5 10 uA VIN = VCC or GND
CS#=VCC
ICC1 VCC Read 1
12 mA
f=104MHz
fT=80MHz (Dual Output)
SCLK=0.1VCC/0.9VCC,
SO=Open
10 mA
f=66MHz
SCLK=0.1VCC/0.9VCC,
SO=Open
4 mA
f=33MHz
SCLK=0.1VCC/0.9VCC,
SO=Open
ICC2 VCC Program Current
(PP) 1 20 mA Program in Progress
CS#=VCC
ICC3
VCC Write Status
Register (WRSR)
Current
15 mA
Program status register in
progress
CS#=VCC
ICC4 VCC Sector Erase
Current (SE) 1 15 mA Erase in Progress
CS#=VCC
ICC5 VCC Chip Erase
Current (CE) 1 20 mA Erase in Progress
CS#=VCC
VIL Input Low Voltage -0.5 0.3VCC V
VIH Input High Voltage 0.7VCC VCC+0.4 V
VOL Output Low Voltage 0.4 VIOL = 1.6mA
VOH Output High Voltage VCC-0.2 V IOH = -100uA
VWI Low VCC Write Inhibit
Voltage 3 2.1 2.3 2.5 V
Table 5. DC CHARACTERISTICS (Temperature = -40°C to 85°C for Industrial grade, VCC = 2.7V ~ 3.6V)
Notes :
1. Typical values at VCC = 3.3V, T = 25°C. These currents are valid for all product versions (package and speeds).
2. Typical value is calculated by simulation.
3. Not 100% tested.
30
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Table 6. AC CHARACTERISTICS (Temperature = -40°C to 85°C for Industrial grade, VCC = 2.7V ~ 3.6V)
Symbol Alt. Parameter Min. Typ. Max. Unit
fSCLK fC
Clock Frequency for the following instructions: FAST_READ,
RDSFDP, PP, SE, BE, CE, DP, RES, RDP, WREN, WRDI,
RDID, RDSR, WRSR
DC 104 MHz
fRSCLK fR Clock Frequency for READ instructions DC 33 MHz
fTSCLK fT Clock Frequency for DREAD instructions DC 80 MHz
tCH(1) tCLH Clock High Time @33MHz 13 ns
@104MHz 4.7 ns
tCL(1) tCLL Clock Low Time @33MHz 13 ns
@104MHz 4.7 ns
tCLCH(2) Clock Rise Time (3) (peak to peak) 0.1 V/ns
tCHCL(2) Clock Fall Time (3) (peak to peak) 0.1 V/ns
tSLCH tCSS CS# Active Setup Time (relative to SCLK) 7 ns
tCHSL CS# Not Active Hold Time (relative to SCLK) 7 ns
tDVCH tDSU Data In Setup Time 2 ns
tCHDX tDH Data In Hold Time 5 ns
tCHSH CS# Active Hold Time (relative to SCLK) 7 ns
tSHCH CS# Not Active Setup Time (relative to SCLK) 7 ns
tSHSL tCSH CS# Deselect Time Read 15 ns
Write 40 ns
tSHQZ(2) tDIS Output Disable Time 6 ns
tCLQV tV Clock Low to Output Valid 30pF 8 ns
15pF 6 ns
tCLQX tHO Output Hold Time 0 ns
tHLCH HOLD# Setup Time (relative to SCLK) 5 ns
tCHHH HOLD# Hold Time (relative to SCLK) 5 ns
tHHCH HOLD Setup Time (relative to SCLK) 5 ns
tCHHL HOLD Hold Time (relative to SCLK) 5 ns
tHHQX(2) tLZ HOLD to Output Low-Z 6 ns
tHLQZ(2) tHZ HOLD# to Output High-Z 6 ns
tWHSL(4) Write Protect Setup Time 20 ns
tSHWL(4) Write Protect Hold Time 100 ns
tDP(2) CS# High to Deep Power-down Mode 10 us
tRES1(2) CS# High to Standby Mode without Electronic Signature Read 8.8 us
tRES2(2) CS# High to Standby Mode with Electronic Signature Read 8.8 us
tW Write Status Register Cycle Time 5 40 ms
tBP Byte-Program 9 300 us
tPP Page Program Cycle Time 1.4 5 ms
tSE Sector Erase Cycle Time 60 300 ms
tBE Block Erase Cycle Time 0.7 2 s
tCE Chip Erase Cycle Time 1 2 s
Note:
1. tCH + tCL must be greater than or equal to 1/f (fC or fR).
2. Value guaranteed by characterization, not 100% tested in production.
3. Expressed as a slew-rate.
4. Only applicable as a constraint for a WRSR instruction when SRWD is set at 1.
5. Test condition is shown as Figure 5 & 6.
6. The CS# rising time needs to follow tCLCH spec and CS# falling time needs to follow tCHCL spec.
31
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Symbol Parameter Min. Max. Unit
tVSL(1) VCC(min) to CS# low 200 us
INITIAL DELIVERY STATE
The device is delivered with the memory array erased: all bits are set to 1 (each byte contains FFh). The Status
Register contains 00h (all Status Register bits are 0).
Note: 1. The parameter is characterized only.
Table 7. Power-Up Timing
32
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 7. Serial Input Timing
Figure 8. Output Timing
LSB
ADDR.LSB IN
tSHQZ
tCH
tCL
tCLQX
tCLQV
tCLQV
SCLK
SO
CS#
SI
SCLK
SI
CS#
MSB
SO
tDVCH
High-Z
LSB
tSLCH
tCHDX
tCHCL
tCLCH
tSHCH
tSHSL
tCHSHtCHSL
Timing Analysis
33
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 9. Hold Timing
* SI is "don't care" during HOLD operation.
Figure 10. WP# Disable Setup and Hold Timing during WRSR when SRWD=1
tCHHL
tHLCH
tHHCH
tCHHH
tHHQXtHLQZ
SCLK
SO
CS#
HOLD#
High-Z
01
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
tWHSL tSHWL
SCLK
SI
CS#
WP#
SO
34
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 11. Write Enable (WREN) Sequence (Command 06)
Figure 12. Write Disable (WRDI) Sequence (Command 04)
Figure 13. Read Identication (RDID) Sequence (Command 9F)
21 34567
High-Z
0
06
Command
SCLK
SI
CS#
SO
21 34567
High-Z
0
04
Command
SCLK
SI
CS#
SO
21 345678910 11 12 13 14 15
Command
0
Manufacturer Identification
High-Z
MSB
15 14 13 3210
Device Identification
MSB
7 6 5 3 2 1 0
16 17 18 28 29 30 31
SCLK
SI
CS#
SO
9F
35
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 14. Read Status Register (RDSR) Sequence (Command 05)
Figure 15. Write Status Register (WRSR) Sequence (Command 01)
Figure 16. Read Data Bytes (READ) Sequence (Command 03)
21 345678910 11 12 13 14 15
command
0
76543210
Status Register Out
High-Z
MSB
76543210
Status Register Out
MSB
7
SCLK
SI
CS#
SO
05
21 3456789 10 11 12 13 14 15
Status
Register In
0
765432 0
1
MSB
SCLK
SI
CS#
SO
01
High-Z
command
SCLK
SI
CS#
SO
23
21 345678910 28 29 30 31 32 33 34 35
22 21 3210
36 37 38
76543 1 7
0
Data Out 1
24-Bit Address
0
MSB
MSB
2
39
Data Out 2
03
High-Z
command
36
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 17. Read at Higher Speed (FAST_READ) Sequence (Command 0B)
23
21 345678910 28 29 30 31
22 21 3210
High-Z
24 BIT ADDRESS
0
32 33 34 36 37 38 39 40 41 42 43 44 45 46
765432 0
1
DATA OUT 1
Dummy Byte
MSB
76543210
DATA OUT 2
MSB MSB
7
47
765432 0
1
35
SCLK
SI
CS#
SO
SCLK
SI
CS#
SO
0B
Command
Figure 18. Dual Output Read Mode Sequence (Command 3B)
High Impedance
21 3456780
SCLK
SI/SO0
SO/SO1
CS#
9 10 11 30 31 32
3B(hex) dummy
address
bit23, bit22, bit21...bit0
data
bit6, bit4, bit2...bit0, bit6, bit4....
data
bit7, bit5, bit3...bit1, bit7, bit5....
39 40 41 42 43
8 Bit Instruction 24 BIT Address 8 dummy
cycle Data Output
37
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 19. Page Program (PP) Sequence (Command 02)
4241 43 44 45 46 47 48 49 50 52 53 54 5540
23
21 3456789 10 28 29 30 31 32 33 34 35
22 21 3210
36 37 38
24-Bit Address
0
765432 0
1
Data Byte 1
39
51
765432 0
1
Data Byte 2
765432 0
1
Data Byte 3 Data Byte 256
2079
2078
2077
2076
2075
2074
2073
765432 0
1
2072
MSB MSB
MSB MSB MSB
SCLK
CS#
SI
SCLK
CS#
SI
02
Command
38
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 20. Sector Erase (SE) Sequence (Command 20)
Note: SE command is 20(hex).
Figure 21. Block Erase (BE) Sequence (Command 52 or D8)
Note: BE command is 52 or D8(hex).
24 Bit Address
21 3456789 29 30 310
23 22 2 1 0
MSB
SCLK
CS#
SI
20
Command
24 Bit Address
21 3456789 29 30 310
23 22 2 0
1
MSB
SCLK
CS#
SI
52 or D8
Command
39
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 22. Chip Erase (CE) Sequence (Command 60 or C7)
Figure 23. Deep Power-down (DP) Sequence (Command B9)
Figure 24. Read Electronic Signature (RES) Sequence (Command AB)
Note: CE command is 60(hex) or C7(hex).
21 345670
60 or C7
SCLK
SI
CS#
Command
21 345670tDP
Deep Power-down Mode
Stand-by Mode
SCLK
CS#
SI
B9
Command
23
21 345678910 28 29 30 31 32 33 34 35
22 21 3210
36 37 38
765432 0
1
High-Z Electronic Signature Out
3 Dummy Bytes
0
MSB
Stand-by Mode
Deep Power-down Mode
MSB
tRES2
SCLK
CS#
SI
SO
AB
Command
40
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 25. Release from Deep Power-down (RDP) Sequence (Command AB)
Figure 26. Read Electronic Manufacturer & Device ID (REMS) Sequence (Command 90)
Notes:
(1) ADD=00H will output the manufacturer's ID rst and ADD=01H will output device ID rst
21 345670tRES1
Stand-by Mode
Deep Power-down Mode
High-Z
SCLK
CS#
SI
SO
AB
Command
15 14 13 3 2 1 0
21 3456789 10
2 Dummy Bytes
0
32 33 34 36 37 38 39 40 41 42 43 44 45 46
765432 0
1
Manufacturer ID
ADD (1)
MSB
76543210
Device ID
MSB MSB
7
47
765432 0
1
3531302928
SCLK
SI
CS#
SO
SCLK
SI
CS#
SO X
90
High-Z
Command
41
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 27. Power-up Timing
VCC
VCC(min)
Chip Selection is Not Allowed
tVSL
time
Device is fully
accessible
VCC(max)
42
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
RECOMMENDED OPERATING CONDITIONS
At Device Power-Up
AC timing illustrated in Figure 28 and Figure 29 are for the supply voltages and the control signals at device power-
up and power-down. If the timing in the gures is ignored, the device will not operate correctly.
During power-up and power-down, CS# needs to follow the voltage applied on VCC to keep the device not to be
selected. The CS# can be driven low when VCC reach Vcc(min.) and wait a period of tVSL.
Notes :
1. Sampled, not 100% tested.
2. For AC spec tCHSL, tSLCH, tDVCH, tCHDX, tSHSL, tCHSH, tSHCH, tCHCL, tCLCH in the gure, please refer to
"AC CHARACTERISTICS" table.
Symbol Parameter Notes Min. Max. Unit
tVR VCC Rise Time 1 5 500000 us/V
Figure 28. AC Timing at Device Power-Up
SCLK
SI
CS#
VCC
MSB IN
SO
tDVCH
High Impedance
LSB IN
tSLCH
tCHDX
tCHCL
tCLCH
tSHCH
tSHSL
tCHSHtCHSL
tVR
VCC(min)
GND
43
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
Figure 29. Power-Down Sequence
CS#
SCLK
VCC
During power-down, CS# needs to follow the voltage drop on VCC to avoid mis-operation.
44
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
ERASE AND PROGRAMMING PERFORMANCE
Parameter Min. Typ. (1) Max. (2) Unit
Write Status Register Cycle Time 5 40 ms
Sector erase Time 60 300 ms
Block erase Time 0.7 2 s
Chip Erase Time 1 2 s
Byte Program Time (via page program command) 9 300 us
Page Program Time 1.4 5 ms
Erase/Program Cycle 100,000 cycles
Notes:
1. Typical program and erase time assumes the following conditions: 25°C, 3.3V, and checker board pattern.
2. Under worst conditions of 85°C and 2.7V.
3. System-level overhead is the time required to execute the rst-bus-cycle sequence for the programming com-
mand.
4. Erase/Program cycles comply with JEDEC: JESD47 & JESD22-A117 standard.
Min. Max.
Input Voltage with respect to GND on all power pins, SI, CS# -1.0V 2 VCCmax
Input Voltage with respect to GND on SO -1.0V VCC + 1.0V
Current -100mA +100mA
Includes all pins except VCC. Test conditions: VCC = 3.0V, one pin at a time.
LATCH-UP CHARACTERISTICS
DATA RETENTION
Parameter Condition Min. Max. Unit
Data retention 55˚C 20 years
45
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
PART NO. CLOCK
(MHz)
OPERATING
CURRENT MAX.
(mA)
STANDBY
CURRENT MAX.
(uA)
Temperature Package Remark
MX25L1006EMI-10G 104 12 25 -40~85°C 8-SOP
(150mil)
RoHS
Compliant
MX25L1006EZUI-10G 104 12 25 -40~85°C 8-USON
(2x3mm)
RoHS
Compliant
ORDERING INFORMATION
46
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
PART NAME DESCRIPTION
MX 25 L 10 M I G
OPTION:
G: RoHS Compliant and Halogen-free
SPEED:
10: 104MHz
TEMPERATURE RANGE:
I: Industrial (-40°C to 85°C)
PACKAGE:
M: 150mil 8-SOP
ZU: 2x3mm 8-USON
DENSITY & MODE:
1006E: 1Mb
TYPE:
L: 3V
DEVICE:
25: Serial Flash
1006E
47
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
PACKAGE INFORMATION
48
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
49
P/N: PM1670 REV. 1.2, AUG. 15, 2013
MX25L1006E
REVISION HISTORY
Revision No. Description Page Date
1.0 1. Removed "Preliminary" P4 APR/15/2011
2. Modied pin name from SI to SI/SIO0 and from SO to SO/SIO1 P5,6
1.1 1. Added Read SFDP (RDSFDP) Mode P4,10,12, FEB/10/2012
P20~25,30
1.2 1. Modied Secured OTP data from 1 to 0 P24 AUG/15/2013
2. Content modication. P17-18
MX25L1006E
50
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specications without notice.
Except for customized products which has been expressly identied in the applicable agreement, Macronix's
products are designed, developed, and/or manufactured for ordinary business, industrial, personal, and/or
household applications only, and not for use in any applications which may, directly or indirectly, cause death,
personal injury, or severe property damages. In the event Macronix products are used in contradicted to their
target usage above, the buyer shall take any and all actions to ensure said Macronix's product qualied for its
actual use in accordance with the applicable laws and regulations; and Macronix as well as it’s suppliers and/or
distributors shall be released from any and all liability arisen therefrom.
Copyright© Macronix International Co., Ltd. 2011~2012. All rights reserved, including the trademarks and
tradename thereof, such as Macronix, MXIC, MXIC Logo, MX Logo, Integrated Solutions Provider, NBit, Nbit,
NBiit, Macronix NBit, eLiteFlash, HybridNVM, HybridFlash, XtraROM, Phines, KH Logo, BE-SONOS, KSMC,
Kingtech, MXSMIO, Macronix vEE, Macronix MAP, Rich Au dio, Rich Book, Rich TV, and FitCAM. The names
and brands of third party referred thereto (if any) are for identication purposes only.
For the contact and order information, please visit Macronix’s Web site at: http://www.macronix.com
