TSOP93338 - VISHAY - Datasheet.Directory

TSOP931.., TSOP933.., TSOP935..

www.vishay.com Vishay Semiconductors

Rev. 1.4, 31-Jul-2019 1Document Number: 82840

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

IR Receiver Modules for Remote Control Systems

ADDITIONAL RESOURCES

FEATURES

• Improved dark sensitivity

• Improved immunity against optical noise

• Very low supply current

• Photo detector and preamplifier in one package

• Internal filter for PCM frequency

• Supply voltage: 2.0 V to 3.6 V

• Insensitive to supply voltage ripple and noise

• Material categorization:

for definitions of compliance please see

www.vishay.com/doc?99912

MECHANICAL DATA

1 = OUT, 2 = GND, 3 = VS

DESCRIPTION

The TSOP93... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems.

These series provide improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the

presence of optical disturbances e.g. from CFLs.

The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The

demodulated output signal can be directly connected to a microprocessor for decoding.

The TSOP931.., TSOP933.., and TSOP935.., series devices are designed to receive short burst codes (6 or more carrier cycles

per burst). The third digit designates the AGC level (AGC1, AGC3, or AGC5) and the last two digits designate the band-pass

frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC3

provides enhanced noise suppression and AGC5 provides maximized noise suppression. Generally, we advise to select the

highest AGC that satisfactorily receives the desired remote code.

These components have not been qualified to automotive specifications.

Note

• 30 kHz and 33 kHz only available on written request

23051

3D Models

PARTS TABLE

AGC LEGACY, FOR SHORT BURSTS

(AGC1)

ENHANCED NOISE SUPPRESSION

(AGC3)

MAXIMIZED NOISE SUPPRESSION

(AGC5)

Carrier

frequency

30 kHz TSOP93130 TSOP93330 TSOP93530

33 kHz TSOP93133 TSOP93333 TSOP93533

36 kHz TSOP93136 TSOP93336 (1)(5) TSOP93536

38 kHz TSOP93138 TSOP93338 (2)(4) TSOP93538

40 kHz TSOP93140 TSOP93340 TSOP93540

56 kHz TSOP93156 TSOP93356 TSOP93556 (3)

Package Minimold

Pinning 1 = OUT, 2 = GND, 3 = VS

Dimensions (mm) 5.4 W x 6.35 H x 4.9 D

Mounting Leaded

Application Remote control

Best choice for (1) RCMM (2) RECS-80 Code (3) r-map (4) XMP-1, XMP-2 (5) MCIR

TSOP931.., TSOP933.., TSOP935..

www.vishay.com Vishay Semiconductors

Rev. 1.4, 31-Jul-2019 2Document Number: 82840

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

BLOCK DIAGRAM APPLICATION CIRCUIT

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

30 kΩ

Demo-

pass

AGCInput

Band

dulator

Control circuit

16833-13

IR receiver

GND

Circuit

μC

+ VS

GND

Transmitter

with

TSALxxxx VS

17170-12

OUT

R1 and C1 recommended to reduce supply ripple for VS < 2.2 V

ABSOLUTE MAXIMUM RATINGS

PARAMETER TEST CONDITION SYMBOL VALUE UNIT

Supply voltage VS-0.3 to +3.6 V

Supply current IS3mA

Output voltage VO-0.3 to (VS + 0.3) V

Output current IO5mA

Junction temperature Tj100 °C

Storage temperature range Tstg -25 to +85 °C

Operating temperature range Tamb -25 to +85 °C

Power consumption Tamb ≤ 85 °C Ptot 10 mW

Soldering temperature t ≤ 10 s, 1 mm from case Tsd 260 °C

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT

Supply current Ev = 0, VS = 3.3 V ISD 0.25 0.37 0.45 mA

Ev = 40 klx, sunlight ISH -0.50- mA

Supply voltage VS2.0 - 3.6 V

Transmission distance Ev = 0, test signal see Fig. 1,

IR diode TSAL6200, IF = 50 mA d-28-m

Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2,

test signal see Fig. 1 VOSL - - 100 mV

Minimum irradiance Test signal: XMP code Ee min.

- 0.12 0.25 mW/m2

Test signal: NEC code - 0.09 0.20

Maximum irradiance tpi - 3.0/f0 < tpo < tpi + 3.5/f0,

test signal see Fig. 1 Ee max. 30 - - W/m2

Directivity Angle of half transmission

distance ϕ1/2 -± 45- °

TSOP931.., TSOP933.., TSOP935..

www.vishay.com Vishay Semiconductors

Rev. 1.4, 31-Jul-2019 3Document Number: 82840

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

Fig. 1 - Output Delay and Pulse-Width

Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient

Fig. 3 - Test Signal

Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient

Fig. 5 - Frequency Dependence of Responsivity

Fig. 6 - Sensitivity in Bright Ambient

14337-5

tpi (1) t

VOH

VOL tpo (3) t

Optical Test Signal

(IR diode TSAL6200, N = 6 pulses, f = f0, T = 10 ms)

Output Signal

td (2)

(2) 4/f0 < td < 10/f0

(3) tpi - 3.0/f0 < tpo < tpi + 3.5/f0

(1) tpi ≥ 6/f0

100

1000

10000

0.05

0.10

0.15

0.20

0.25

0.30

0.1 10 1000 100 000

Axis Title

1st line

2nd line

tpo - Output Pulse Width (ms)

Ee- Irradiance (mW/m2)

Output pulse width

Input burst length

λ= 950 nm,

optical test signal, Fig. 1

600 µs 600 µs

t = 60 ms

off

94 8134

Optical Test Signal

Output Signal, (see Fig. 4)

100

1000

10000

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

0.1 1 10 100 1000 10 000 100 000

Axis Title

1st line

2nd line

ton, toff - Output Pulse Width (ms)

Ee- Irradiance (mW/m2)

ton

toff

λ= 950nm,

optical test signal, Fig. 3

100

1000

10000

0.2

0.4

0.6

0.8

1.0

1.2

0.7 0.9 1.1 1.3

Axis Title

1st line

2nd line

Ee min./Ee- Relative Responsivity

f/f0- Relative Frequency

f = f

±5 %

∆f (3 dB) = f

/10

100

1000

10000

0.01 0.1 1 10 100

Axis Title

1st line

2nd line

Ee min. - Threshold Irradiance (mW/m2)

Ee- Ambient DC Irradiance (W/m2)

Correlation with ambient light sources:

10 W/m2= 1.4 klx (std. ilum. A, T = 2855 K)

10 W/m2= 8.2 klx (daylight, T = 5900 K)

Wavelength of ambient

illumination: λ = 950 nm

TSOP931.., TSOP933.., TSOP935..

www.vishay.com Vishay Semiconductors

Rev. 1.4, 31-Jul-2019 4Document Number: 82840

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Fig. 7 - Sensitivity vs. Supply Voltage Disturbances

Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length

Fig. 9 - Sensitivity vs. Ambient Temperature

Fig. 10 - Relative Spectral Sensitivity vs. Wavelength

Fig. 11 - Directivity

Fig. 12 - Sensitivity vs. Supply Voltage

100

1000

10000

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1101001000

Axis Title

1st line

2nd line

e min.

- Threshold Irradiance (mW/m

)

∆V

S RMS

- AC Voltage on DC Supply Voltage (mV)

f = 100 Hz

f = 10 kHz

f = 30 kHz

f = f

100

1000

10000

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

0 20406080100120140

Axis Title

1st line

2nd line

Maximum Envelope Duty Cycle

Burst Length (Number of Cycles/Burst)

TSOP933..

TSOP935..

f = 38 kHz, E = 2 mW/m2

TSOP931..

100

1000

10000

0.05

0.10

0.15

0.20

0.25

0.30

-30 -10 10 30 50 70 90

Axis Title

1st line

2nd line

Ee min. - Threshold Irradiance (mW/m2)

Tamb - Ambient Temperature (°C)

100

1000

10000

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

750 850 950 1050 1150

Axis Title

1st line

2nd line

S(λ)rel. - Relative Spectral Sensitivity

λ - Wavelength (nm)

Axis Title

2nd line

drel. - Relative Transmission Distance

1.0

0.9

0.7

0.8

30°

50°

40°

80°

0.6 0.4 0.200.40.2 0.6

20°10°0°

60°

70°

100

1000

10000

0.05

0.10

0.15

0.20

0.25

0.30

1.0 1.5 2.0 2.5 3.0 3.5 4.0

Axis Title

1st line

2nd line

Ee min. - Threshold Irradiance (mW/m2)

VS- Supply Voltage (V)

TSOP931.., TSOP933.., TSOP935..

www.vishay.com Vishay Semiconductors

Rev. 1.4, 31-Jul-2019 5Document Number: 82840

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

SUITABLE DATA FORMAT

This series is designed to suppress spurious output pulses

due to noise or disturbance signals. The devices can

distinguish data signals from noise due to differences in

frequency, burst length, and envelope duty cycle. The data

signal should be close to the device’s band-pass center

frequency (e.g. 38 kHz) and fulfill the conditions in the table

below.

When a data signal is applied to the product in the presence

of a disturbance, the sensitivity of the receiver is

automatically reduced by the AGC to insure that no spurious

pulses are present at the receiver’s output. Some examples

which are suppressed are:

• DC light (e.g. from tungsten bulbs sunlight)

• Continuous signals at any frequency

• Strongly or weakly modulated patterns from fluorescent

lamps with electronic ballasts (see Fig. 13 or Fig. 14)

Fig. 13 - IR Emission from Fluorescent Lamp

With Low Modulation

Fig. 14 - IR Emission from Fluorescent Lamp

With High Modulation

Note

• For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP932.., TSOP934.., or TSOP936..

16920

100

1000

10000

0 5 10 15 20

Axis Title

1st line

2nd line

IR Signal Amplitude

Time (ms)

16921

100

1000

10000

-60

-40

-20

0 5 10 15 20

Axis Title

1st line

2nd line

IR Signal Amplitude

Time (ms)

TSOP931.. TSOP933.. TSOP935..

Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst

After each burst of length

A gap time is required of

6 to 70 cycles

≥ 6 cycles

6 to 20 cycles

≥ 8 cycles

6 to 38 cycles

≥ 8 cycles

For bursts greater than

a minimum gap time in the data stream is needed of

70 cycles

> 1 x burst length

20 cycles

> 6 x burst length

38 cycles

> 20 ms

Maximum number of continuous short bursts/second 3000 2500 2500

RCMM code Yes Preferred Yes

XMP-1 code Yes Preferred Yes

r-map code Yes Yes Preferred

RECS-80 code Yes Preferred Yes

MCIR Yes Preferred Yes

Suppression of interference from fluorescent lamps Fig. 13 Fig. 13 and Fig. 14 Fig. 13 and Fig. 14

TSOP931.., TSOP933.., TSOP935..

www.vishay.com Vishay Semiconductors

Rev. 1.4, 31-Jul-2019 6Document Number: 82840

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PACKAGE DIMENSIONS in millimeters

Marking area

123

Cavity number

R2.5

2.25

(3 x)

0.3 ± 0.1

(3 x) 0.6 ± 0.1

2.54 nom.

6.35

15.2 ± 0.3

0.95

(3 x) 0.85 max.

(5.05)

7.6

(0.95)

(1.1)

5.4

Drawing-No.: 6.550-5335.01-4

Issue: 2; 02.07.19

Technical drawings

according to DIN

specications

Not indicated tolerances ± 0.2

TSOP931.., TSOP933.., TSOP935..

www.vishay.com Vishay Semiconductors

Rev. 1.4, 31-Jul-2019 7Document Number: 82840

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

BULK PACKAGING

Standard shipping for minimold is in conductive plastic bags. The packing quantity is determined by weight and the number of

components per carton may vary by a maximum of ± 0.3 %.

ORDERING INFORMATION

Examples: TSOP93338

TSOP93356VI1

TSOP93338SS1F

For more information, see: www.vishay.com/doc?80076

PACKAGING QUANTITY

• 300 pieces per bag (each bag is individually boxed)

• 6 bags per carton

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 01-Jan-2021 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.