MicroCapacitance (MC) SC SIDACtor(R) Device RoHS This SCMC SIDACtor series enables equipment to comply with various regulatory requirements including GR 1089, IEC 60950, UL 60950, TIA-968-A (formerly known as FCC Part 68), and ITU K.20, K.21, and K.45. Electrical Parameters Part Number * VDRM Volts VS Volts VT Volts IDRM Amps IS mAmps IT Amps IH mAmps P0080SCMCL 6 25 4 5 800 2.2 50 P0220SCMCL 15 32 4 5 800 2.2 50 P0300SCMCL 25 40 4 5 800 2.2 50 P0640SCMCL 58 77 4 5 800 2.2 150 P0720SCMCL 65 88 4 5 800 2.2 150 P0900SCMCL 75 98 4 5 800 2.2 150 P1100SCMCL 90 130 4 5 800 2.2 150 P1200SCMCL 100 130 4 5 800 2.2 120 P1300SCMCL 120 160 4 5 800 2.2 150 P1500SCMCL 140 180 4 5 800 2.2 150 P1800SCMCL 170 220 4 5 800 2.2 150 P2000SCMCL 180 220 4 5 800 2.2 120 P2100SCMCL 180 240 4 5 800 2.2 150 P2300SCMCL 190 260 4 5 800 2.2 150 P2500SCMCL 230 290 4 5 800 2.2 120 P2600SCMCL 220 300 4 5 800 2.2 150 P3100SCMCL 275 350 4 5 800 2.2 150 P3500SCMCL 320 400 4 5 800 2.2 150 * "L" in part number indicates RoHS compliance. For non-RoHS compliant device, delete "L" from part number. For surge ratings, see table below. General Notes: * All measurements are made at an ambient temperature of 25 C. IPP applies to -40 C through +85 C temperature range. * IPP is a repetitive surge rating and is guaranteed for the life of the product. * Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities. * VDRM is measured at IDRM. * VS is measured at 100 V/s. * Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request. Series Surge Ratings in Amps C IPP 0.2x310 * 2x10 * 8x20 * 0.5x700 ** 2x10 ** 1.2x50 ** 10x160 * 10x160 ** 10x560 * 10x560 ** 5x320 * 9x720 ** 10x360 * 10x1000 * 5x310 * ITSM 10x360 ** 10x1000 ** 10x700 ** 50 / 60 Hz di/dt Amps Amps Amps Amps Amps Amps Amps Amps Amps Amps Amps/s 50 500 400 200 150 200 175 100 200 30 500 * Current waveform in s ** Voltage waveform in s Telecom Design Guide * (c) 2006 Littelfuse 3-5 www.littelfuse.com SIDACtor Devices These DO-214AA SCMC SIDACtor devices are intended for applications sensitive to load values. Typically, high speed connections, such as xDSL and T1/E1, require a lower capacitance. CO values for the MicroCapacitance device are 40 percent lower than a standard SC part. MicroCapacitance (MC) SC SIDACtor(R) Device Thermal Considerations Package Symbol DO-214AA TJ Operating Junction Temperature Range -40 to +150 C TS Storage Temperature Range -65 to +150 C 90 C/W RJA Parameter Thermal Resistance: Junction to Ambient Value Unit Capacitance Values pF Part Number MIN MAX P0080SCMCL 35 75 P0220SCMCL 30 65 P0300SCMCL 25 45 P0640SCMCL 55 85 P0720SCMCL 50 75 P0900SCMCL 45 70 P1100SCMCL 45 70 P1200SCMCL 45 65 P1300SCMCL 40 60 P1500SCMCL 35 55 P1800SCMCL 35 50 P2000SCMCL 35 50 P2100SCMCL 30 50 P2300SCMCL 30 50 P2500SCMCL 30 45 P2600SCMCL 30 45 P3100SCMCL 30 45 P3500SCMCL 25 40 Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. www.littelfuse.com 3-6 (c) 2006 Littelfuse * Telecom Design Guide MicroCapacitance (MC) SC SIDACtor(R) Device IT IS IH IDRM -V +V VT VDRM VS Peak Value 100 tr = rise time to peak value td = decay time to half value Waveform = tr x td 50 SIDACtor Devices IPP - Peak Pulse Current - %IPP +I Half Value 0 0 tr td t - Time (s) -I 14 12 10 IH 8 6 25 C 4 2 IH (TC = 25 C) tr x td Pulse Waveform Ratio of Percent of VS Change - % V-I Characteristics 0 -4 2.0 1.8 1.6 1.4 25 C 1.2 1.0 0.8 0.6 0.4 -40 -20 0 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 Case Temperature (TC) - C 20 40 60 80 100 120 140 160 Junction Temperature (TJ) - C Normalized VS Change versus Junction Temperature Telecom Design Guide * (c) 2006 Littelfuse Normalized DC Holding Current versus Case Temperature 3-7 www.littelfuse.com