SWITCHING AND CONTROL
www.keithley.com
1.888.KEITHLEY (U.S. only)
A Greater Measure of Confidence
•Quad 1×10 multiplexer for
2-, 4-, or 8-pole operation
•Connects to 7001/7002
backplane for easy
expandability
•500nV, 100pA offsets
MULTIPLEX CONFIGURATION: Four in de pen dent 1×10 2-pole multiplex banks or two in de pen dent 1×10 4-pole multiplex banks.
Ad ja cent banks can be connected together. Jump ers can be removed to isolate any bank from the backplane.
CONTACT CONFIGURATION: 2-pole Form A (Hi, Lo) (1-pole form C for 7111-S).
CONNECTOR TYPE:
7011-C: 96-pin male DIN connector.
7011-S and 7111-S: Screw terminal, #16AWG maximum wire size, with 0.092 inch O.D. 28 conductors per card maximum.
#22AWG typical wire size with 0.062 inch O.D. 88 conductors per card maximum.
MAXIMUM SIGNAL LEVEL:
DC Signals: 110V DC between any two pins, 1A switched. 30VA (re sis tive load).
AC Signals: 125V rms and 175V AC peak, between any two pins, 1A switched, 60VA (resistive load).
COMMON MODE VOLTAGE: 175V peak, any pin to chassis.
CONTACT LIFE: Cold Switching: 108 closures. At Maximum Signal Levels: 105 closures.
CHANNEL RESISTANCE (per conductor): <1W.
CONTACT POTENTIAL: 7011-C: <1µV per channel contact pair 7011-S, 7111-S: <2µV per contact pair
<3µV typical per single contact. <5µV typical per single contact.
OFFSET CURRENT: <100pA.
ACTUATION TIME: 3ms.
ISOLATION:
Bank: >109W, <25pF.
Channel to Channel: >109W, <50pF.
Differential: Configured as 1×10:
>109W, <100pF. Configured as 1×40:
>109W, <200pF.
Common Mode: Configured as 1×10:
>109W, <200pF. Configured as 1×40:
>109W, <600pF.
CROSSTALK (1MHz, 50W Load): Bank:
<–40dB. Channel: <–40dB.
INSERTION LOSS (50W Source, 50W
Load): <0.1dB below 1MHz, <3dB
below 2MHz.
RELAY DRIVE CURRENT (per relay):
7011-C, -S: 16mA
7111-S: 28mA
ACCESSORIES AVAILABLE
FOR 7011-C:
7011-KIT-R 96-pin Female Connector Kit
7011-MTC-1 96-pin Mass Terminated Cable, Female to
Female, 1m
7011-MTC-2 96-pin Mass Terminated Cable, Female to
Female, 2m
FOR 7011-S AND 7111-S:
7011-ST Extra Screw Terminal Connection Board
SERVICES AVAILABLE
7011-C-3Y-EW 1-year factory warranty extended to 3 years
from date of shipment
7011-S-3Y-EW 1-year factory warranty extended to 3 years
from date of shipment
7111-S-3Y-EW 1-year factory warranty extended to 3 years
from date of shipment
Ordering Information
7011-C Quad 1×10 Multiplexer
with 96-pin
Mass Terminated
Connector Board
7011-S Quad 1×10 Multiplexer
with Screw Terminal
Connector Board
7111-S Quad 1×10 Form
C Multiplexer with
Screw Terminal
Connector Board
Channel 1
HI
LO
Bank A Channels 2-9
HI
LO
Channel 10
HI
Output
LO
J
J
HI
LO
Backplane
Channel 1
HI
LO
Bank D Channels 2-9
HI
LO
Channel 10
HI
Output
LO
J
J
HI
LO
Backplane
Banks B –C
JJ
JJ
7011-C
The Model 7011 40-channel multiplexer has four independent banks of 1×10
switching. Each channel is 2-pole. These four banks can be combined for a
wide variety of switching configurations—for example, dual 1×20, or 1×10 and
1×30, or one large 1×40. The 7001 main frame can au to mat i cal ly configure
the 7011 to switch 4-pole signals by combining channel pairs. This gives you a
dual 1×10 4- pole mul ti plex er or a single 1×20 4-pole multiplexer.
Each of the four multiplexer outputs on this card connects to the 7001/7002
analog back plane through removable jumpers for even greater flexibility. Two
7011 cards can be used to make a single 1×80 multiplexer with all intercard
connections through the backplane. The 7011 mul ti plex er outputs can also be
connected to the rows of the 7012 via the backplane for row expansion.
The Model 7111-S is a form C version of the 7011-S. The 7111-S is a low- voltage,
quad 1×10, single-pole form C multiplexer card. The 7111-S assembly consists
of a screw terminal connector card and a relay card. External test circuits are
wired directly to the screw terminals of the connector card.
These cards automatically configure the 7001 or 7002 mainframe. Two con nec-
tion options are available, screw terminal for maximum flex i bil i ty or a single
96-pin quick disconnect con nector.
7011-C, 7011-S,
7111-S
40-channel Multiplexer Cards
Quad 1×10 Multiplexer Configuration
Use with 7001 and 7002 switch mainframes
Use with 7001 and 7002 switch mainframes
