19-1328; Rev 5; 6/07 Low-Voltage, CMOS Analog Multiplexers/Switches ____________________________Features The MAX4581/MAX4582/MAX4583 are low-voltage, CMOS analog ICs configured as an 8-channel multiplexer (MAX4581), two 4-channel multiplexers (MAX4582), and three single-pole/double-throw (SPDT) switches (MAX4583). These CMOS devices can operate continuously with 2V to 6V dual power supplies or a +2V to +12V single supply. Each switch can handle rail-to-rail analog signals. The off-leakage current is only 1nA at +25C or 5nA at +85C. Offered in Automotive Temperature Range (-40C to +125C) Guaranteed On-Resistance 80 with 5V Supplies with Single +5V Supply 150 Guaranteed On-Resistance Match Between Channels Guaranteed Low Off-Leakage Current 1nA at +25C Guaranteed Low On-Leakage Current 1nA at +25C +2V to +12V Single-Supply Operation 2V to 6V Dual-Supply Operation TTL/CMOS-Logic Compatible Low Distortion: < 0.02% (600) Low Crosstalk: < -96dB (50, MAX4582) High Off-Isolation: < -74dB (50) All digital inputs have 0.8V to 2.4V logic thresholds, ensuring TTL/CMOS-logic compatibility when using a single +5V or dual 5V supplies. ________________________Applications Battery-Operated Equipment Audio and Video Signal Routing Ordering Information Low-Voltage Data-Acquisition Systems Communications Circuits Automotive PINPACKAGE PKG CODE 0C to +70C 16 Plastic DIP P16-1 0C to +70C 16 Narrow SO S16-2 0C to +70C 16 TSSOP U16-2 PART TEMP RANGE MAX4581CPE MAX4581CSE MAX4581CUE Ordering Information continued at end of data sheet. ____________________________________Pin Configurations/Functional Diagrams TOP VIEW MAX4582 MAX4581 MAX4583 X4 1 16 VCC Y0 1 16 VCC Y1 1 16 VCC X6 2 15 X2 Y2 2 15 X2 Y0 2 15 Y X 3 14 X1 Y 3 14 X1 Z1 3 14 X X7 4 13 X0 Y3 4 13 X Z 4 13 X1 X5 5 12 X3 Y1 5 12 X0 Z0 5 12 X0 11 A ENABLE 6 11 X3 ENABLE 6 11 A 10 B VEE 7 VEE 7 10 B ENABLE 6 VEE 7 GND 8 LOGIC 9 C GND 8 DIP/SO/QSOP/TSSOP LOGIC 10 A 9 DIP/SO/QSOP/TSSOP B GND 8 9 C DIP/SO/QSOP/TSSOP Pin Configurations continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products 1 For pricing delivery, and ordering information please contact Maxim Direct at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. MAX4581/MAX4582/MAX4583 ________________General Description MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches ABSOLUTE MAXIMUM RATINGS Voltages Referenced to VEE VCC .........................................................................-0.3V to 13V Voltage into Any Terminal (Note 1) ...(VEE - 0.3V) to (VCC + 0.3V) Continuous Current into Any Terminal..............................20mA Peak Current, X_, Y_, Z_ (pulsed at 1ms, 10% duty cycle) ...................................40mA ESD per Method 3015.7 ..................................................>2000V Continuous Power Dissipation (TA = +70C) 16-Pin Plastic DIP (derate 10.53mW/C above +70C)....842mW 16-Pin Narrow SO (derate 8.70mW/C above +70C) .....696mW 16-Pin QSOP (derate 8.3mW/C above +70C)...............667mW 16-Pin TSSOP (derate 6.7mW/C above +70C) .............457mW 16-Pin QFN (derate 18.5mW/C above +70C) .............1481mW Operating Temperature Ranges MAX458_C_ .........................................................0C to +70C MAX458_E_ ......................................................-40C to +85C MAX458_A_.....................................................-40C to +125C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Note 1: Voltages exceeding VCC or VEE on any signal terminal are clamped by internal diodes. Limit forward-diode current to maximum current rating. Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS--Dual Supplies (VCC = 4.5V to 5.5V, VEE = -4.5V to -5.5V, V_H = 2.4V, V_L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS TEMP MIN TYP MAX UNITS (Note 2) ANALOG SWITCH Analog-Signal Range VX, VY, VZ C, E, A VEE VCC Switch On-Resistance RON VCC = 4.5V; VEE = -4.5V; IX, IY, IZ = 1mA; VX, VY, VZ = 3.5V +25C Switch On-Resistance Match Between Channels (Note 3) RON VCC = 4.5V; VEE = -4.5V; IX, IY, IZ = 1mA; VX, VY, VZ = 3.5V +25C Switch On-Resistance Flatness (Note 4) RFLAT(ON) VCC = 5V; VEE = -5V; IX, IY, IZ = 1mA; VX, VY, VZ = 3V, 0V, -3V +25C X_, Y_, Z_ Off-Leakage (Note 5) IX_(OFF), IY_(OFF), IZ_(OFF) VCC = 5.5V; VEE = -5.5V; VX_, VY_, VZ_ = 4.5V; VX, VY, VZ = 4.5V +25C -1 +1 C, E, A -10 +10 +25C -2 +2 X, Y, Z Off-Leakage (Note 5) IX(OFF), IY(OFF), IZ(OFF) VCC = 5.5V; VEE = -5.5V; VX_, VY_, VZ_ = 4.5V; VX, VY, VZ = 4.5V C, E, A -100 +100 +25C -1 +1 C, E, A -50 +50 +25C -2 +2 C, E, A -100 +100 +25C -1 +1 C, E, A -50 +50 X, Y, Z On-Leakage (Note 5) IX(ON), IY(ON), IZ(ON) C, E, A MAX4581 MAX4582 MAX4583 MAX4582 MAX4583 80 100 1 C, E, A MAX4581 VCC = 5.5V; VEE = -5.5V; VX, VY, VZ = 4.5V 50 4 6 4 C, E, A 10 12 V nA nA nA DIGITAL I/O Logic Input Logic Threshold High VAH, VBH, VCH C, E, A Logic Input Logic Threshold Low VAL, VBL, VCL C, E, A 2 1.5 0.8 1.5 _______________________________________________________________________________________ 2.4 V V Low-Voltage, CMOS Analog Multiplexers/Switches (VCC = 4.5V to 5.5V, VEE = -4.5V to -5.5V, V_H = 2.4V, V_L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) CONDITIONS TEMP MIN TYP MAX UNITS (Note 2) PARAMETER SYMBOL Input-Current High IAH, IBH, ICH VA, VB, VC = 2.4V C, E, A -1 +1 A Input-Current Low IAL, IBL, ICL VA, VB, VC = 0.8V C, E, A -1 +1 A SWITCH DYNAMIC CHARACTERISTICS Inhibit Turn-On Time t(ON) VX_, VY_, VZ_ = 3V; RL = 300; CL = 35pF; Figure 3 TA = +25C Inhibit Turn-Off Time t(OFF) VX_, VY_, VZ_ = 3V; RL = 300; CL = 35pF; Figure 3 TA = +25C Address Transition Time tTRANS VX_, VY_, VZ_ = 3V; RL = 300; CL = 35pF; Figure 2 TA = +25C Break-Before-Make Time tBBM Charge Injection (Note 6) Q 4 CX(ON), CY(ON), CZ(ON) VX_, VY_, VZ_ = 0V; f = 1MHz; Figure 7 Off-Isolation VISO RL = 50, f = 1MHz, Figure 6 Channel-to-Channel Crosstalk VCT RL = 50, f = 1MHz, Figure 6 VCC, VEE Power-Supply Current ICC, IEE 4 MAX4581 MAX4582 ns 5 pC pF pF 6 25 TA = +25C 17 MAX4583 pF 12.5 TA = +25C -74 dB MAX4581 TA = +25C -78 MAX4582 TA = +25C -96 MAX4583 TA = +25C -73 pF TA = +25C 0.02 % C, E, A VCC = 5.5V, VEE = -5.5V, VA, VB, VC, VEnable = V+ or 0 ns ns 10 MAX4581 RL = 600, 5Vp-p, f = 20Hz to 20kHz 20 ns 18 TA = +25C MAX4583 MAX4582 200 200 TA = +25C VX_, VY_, VZ_ = 0V; f = 1MHz; Figure 7 POWER SUPPLY Power-Supply Range 90 C, E, A 0.5 CX(OFF), CY(OFF), CZ(OFF) 100 150 TA = +25C Output Off-Capacitance THD C, E, A C = 1nF, RS = 0, VS = 0V VX_, VY_, VZ_ = 0V; f = 1MHz; Figure 7 Total Harmonic Distortion 40 TA = +25C CX_(OFF), CY_(OFF), CZ_(OFF) 200 200 VX_, VY_, VZ_ = 3V; RL = 300; CL = 35pF; Figure 4 Input Off-Capacitance Output On-Capacitance 100 C, E, A 2 dB 6 TA = +25C -1 +1 C, E, A -10 +10 V A _______________________________________________________________________________________ 3 MAX4581/MAX4582/MAX4583 ELECTRICAL CHARACTERISTICS--Dual Supplies (continued) MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches ELECTRICAL CHARACTERISTICS--Single +5V Supply (VCC = 4.5V to 5.5V, VEE = 0V, V_H = 2.4V, V_L = 0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS TEMP MIN TYP MAX UNITS (Note 2) ANALOG SWITCH Analog-Signal Range VX_, VY_, VZ_, VX, VY, VZ Switch On-Resistance RON VCC = 4.5V; IX, IY, IZ = 1mA; VX, VY, VZ = 3.5V TA = +25C C, E, A Switch On-Resistance Match Between Channels (Note 3) RON VCC = 4.5V; IX, IY, IZ = 1mA; VX, VY, VZ = 3.5V TA = +25C X_, Y_, Z Off-Leakage (Note 5) IX_(OFF), IY_(OFF), IZ_(OFF) VCC = 5.5V; VX_, VY_, VZ_ = 1V, 4.5V; VX, VY, VZ = 4.5V, 1V TA = +25C -1 +1 C, E, A -10 +10 X, Y, Z Off-Leakage (Note 5) IX(OFF), IY(OFF), IZ(OFF) VCC = 5.5V; VX_, VY_, VZ_ = 1V, 4.5V; VX, VY, VZ = 4.5V, 1V X, Y, Z On-Leakage (Note 5) IX(ON), IY(ON), IZ(ON) VCC = 5.5V; VX, VY, VZ = 4.5V, 1V TA = +25C C, E, A TA = +25C C, E, A TA = +25C C, E, A TA = +25C C, E, A -2 -100 -1 -50 -2 -100 -1 -50 +2 +100 +1 +50 +2 +100 +1 +50 C, E, A VEE VCC V 90 150 200 2 8 C, E, A MAX4581 MAX4582 MAX4583 MAX4581 MAX4582 MAX4583 10 nA nA nA DIGITAL I/O Logic Input Logic Threshold High VAH, VBH, VCH, VENABLEH C, E, A Logic Input Logic Threshold Low VAL, VBL, VCL, VENABLEL C, E, A 0.8 Input-Current High IAH, IBH, ICH, IENABLEH VAL, VBL, VCL, VEnableL = 2.4V C, E, A -1 +1 A Input-Current Low IAL, IBL, ICL, IENABLEL VAL, VBL, VCL, VEnableL = 0.8V C, E, A -1 +1 A 5 200 250 100 150 200 250 pC SWITCH DYNAMIC CHARACTERISTICS C = 1nF, RS = 0, VS = 2.5V Charge Injection (Note 6) Q 1.5 Enable Turn-On Time t(ON) VX_, VY_, VZ_ = 3V, RL = 300, CL = 35pF, Figure 3 Enable Turn-Off Time t(OFF) VX_, VY_, VZ_ = 3V, RL = 300, CL = 35pF, Figure 3 Address Transition Time tTRANS VX_, VY_, VZ_ = 3V/0V, RL = 300, CL = 35pF, Figure 2 TA = +25C TA = +25C C, E, A TA = +25C C, E, A TA = +25C C, E, A VX_, VY_, VZ_ = 3V, RL = 300, CL = 35pF, Figure 4 TA = +25C 10 C, E, A TA = +25C C, E, A 2 -1 -10 Break-Before-Make Time POWER SUPPLY Power-Supply Range Power-Supply Current 4 tBBM VCC, VEE ICC, IEE VCC = 3.6V; VA, VB, VC, VEnable = V+ or 0 2.4 1.5 0.8 100 40 80 V 30 _______________________________________________________________________________________ V ns ns ns ns 12 +1 +10 V A Low-Voltage, CMOS Analog Multiplexers/Switches (VCC = 2.7V to 3.6V, VEE = 0V, V_H = 2.0V, V_L = 0.5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS TEMP MIN TYP MAX UNITS (Note 2) ANALOG SWITCH Analog-Signal Range VX_, VY_, VZ_, VX, VY, VZ Switch On-Resistance RON X_, Y_, Z_ Off-Leakage (Note 5) C, E, A VEE V 450 550 VCC = 2.7V; IX, IY, IZ = 0.1mA; VX, VY, VZ = 1.5V TA = +25C C, E, A IX_(OFF), IY_(OFF), IZ_(OFF) VCC = 3.6V; VX_, VY_, VZ_ = 1V, 3V; VX, VY, VZ = 3V, 1V TA = +25C -1 +1 C, E, A -10 +10 X, Y, Z Off-Leakage (Note 6) IX(OFF), IY(OFF), IZ(OFF) VCC = 3.6V; VX_, VY_, VZ_ = 1V, 3.0V; VX, VY, VZ = 3.0V, 1V X, Y, Z On-Leakage (Note 6) IX(ON), IY(ON), IZ(ON) VCC = 3.6V; VX, VY, VZ = 3.0V, 1V TA = +25C C, E, A TA = +25C C, E, A TA = +25C C, E, A TA = +25C C, E, A -2 -100 -1 -50 -2 -100 -1 -50 +2 +100 +1 +50 +2 +100 +1 +50 MAX4581 MAX4582 MAX4583 MAX4581 MAX4582 MAX4583 190 VCC nA nA nA DIGITAL I/O Logic Input Logic Threshold High VAH, VBH, VCH, VENABLEH C, E, A Logic Input Logic Threshold Low VAL, VBL, VCL, VENABLEL C, E, A 0.5 Input-Current High IAH, IBH, ICH, IENABLEH VA, VB, VC = VEnable = 2.0V C, E, A -1 +1 A Input-Current Low IAL, IBL, ICL, IENABLEL VA, VB, VC = VEnable = 0.5V C, E, A -1 +1 A 1.0 SWITCH DYNAMIC CHARACTERISTICS (Note 6) SWITCH DYNAMIC CHARACTERISTICS VX_, VY_, VZ_ = 1.5V; RL = 300; Enable Turn-On Time t(ON) CL = 35pF; Figure 3 Enable Turn-Off Time t(OFF) Address Transition Time tTRANS Break-Before-Make Time tBBM TA = +25C C, E, A TA = +25C VX_, VY_, VZ_ = 1.5V; RL = 300; CL = 35pF; Figure 3 C, E, A TA = +25C VX_, VY_, VZ_ = 1.5V/0V; RL = 300; CL = 35pF; Figure 2 C, E, A VX_, VY_, VZ_ = 1.5V; RL = 300; CL = 35pF TA = +25C 15 TA = +25C C, E, A -1 -10 2.0 1.0 170 50 130 V V 300 400 200 300 300 400 40 ns ns ns ns POWER SUPPLY Power-Supply Current ICC, IEE VCC = 3.6V, VA, VB, VC, VEnable = V+ or 0 +1 +10 A Note 2: The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column. Note 3: RON = RON(MAX) - RON(MIN). Note 4: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal ranges; i.e., VX_, VY_, VZ_ = 3V to 0 and 0 to -3V. Note 5: Leakage parameters are 100% tested at maximum-rated hot operating temperature, and guaranteed by correlation at TA = +25C. Note 6: Guaranteed by design, not production tested. _______________________________________________________________________________________ 5 MAX4581/MAX4582/MAX4583 ELECTRICAL CHARACTERISTICS--Single +3V Supply Typical Operating Characteristics (VCC = 5V, VEE = -5V, GND = 0V, TA = +25C, unless otherwise noted.) ON-RESISTANCE vs. VX, VY, VZ AND TEMPERATURE (DUAL SUPPLIES) TA = +85C 55 VCC = 2.7V, VEE = -2.7V VCC = 1.2V TA = +70C VCC = 2V 1000 VCC = 2.7V RON () 45 RON () VCC = 2V, VEE = -2V 10,000 MAX4581toc02 VCC = 1.2V, VEE = -1.2V 100 65 MAX4581/2/3 toc01 1000 ON-RESISTANCE vs. VX, VY, VZ (SINGLE SUPPLY) MAX4581 toc03 ON-RESISTANCE vs. VX, VY, VZ (DUAL SUPPLIES) RON () 35 VCC = 3.3V VCC = 5V TA = +25C 100 25 VCC = 3.3V, VEE = -3.3V VCC = 5V, VEE = -5V 15 VCC = 10V 10 10 -4 -3 -2 -1 0 1 2 3 4 -5 5 -4 -3 -2 -1 0 1 2 3 4 0 5 1 2 3 4 ON-RESISTANCE vs. VX, VY, VZ AND TEMPERATURE (SINGLE SUPPLY) TA = +85C TA = +70C 110 6 7 OFF-LEAKAGE vs. TEMPERATURE 100 MAX4581toc04 130 5 VX, VY, VZ (V) VX, VY, VZ (V) VX, VY, VZ (V) MAX4581/2/3-05 -5 VCC = 7.5V TA = 0C TA = -40C 5 VCC = 5.5V VEE = -5.5V 10 RON () OFF LEAKAGE (nA) TA = +25C 90 70 50 TA = -40C TA = 0C 1 I X, I Y, I Z 0.1 30 IX_, IY_, IZ_ 0.01 10 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 -50 -25 VX, VY, VZ (V) ON-LEAKAGE vs. TEMPERATURE 0 25 50 75 TEMPERATURE (C) 100 125 CHARGE INJECTION vs. VX, VY, VZ VCC = 5.5V VEE = -5.5V 10,000 MAX4581-07 1.5 MAX4581/2/3-toc-6 100,000 1.0 0.5 0 1000 Q (pC) ON LEAKAGE (pA) MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches 100 -0.5 VCC = 5V VEE = 0V -1.0 VCC = 5V VEE = -5V -1.5 10 -2.0 1 -2.5 -50 6 -25 0 25 50 75 TEMPERATURE (C) 100 125 -5 -4 -3 -2 -1 0 1 2 3 VX, VY, VZ (V) _______________________________________________________________________________________ 4 5 8 9 10 Low-Voltage, CMOS Analog Multiplexers/Switches SUPPLY CURRENT vs. TEMPERATURE FREQUENCY RESPONSE VCC = 5V VEE = -5V VA, VB,VC,VENABLE = 0V, 5V LOSS (dB) ICC, IEE (nA) 0.1 0.01 0 25 50 75 TEMPERATURE (C) 100 -70 -80 -20 -40 ON-PHASE -90 -100 -60 -80 -110 -120 -110 -120 125 0.1 1 10 100 FREQUENCY (MHz) TOTAL HARMONIC DISTORTION vs. FREQUENCY VCC CURRENT vs. LOGIC LEVEL (VA, VB, VC, VENABLE) 600 IN AND OUT MAX4581-11 1 MAX4581-10 100 10-1 10-2 10 10-3 VCC = 12V ICC (A) 10-4 1 10-5 10-6 VCC = 5V 10-7 10-8 0.1 10-9 10-10 10-11 0.01 100 1k 10k 100k 0 FREQUENCY (Hz) 1 2 3 4 5 6 7 8 9 10 11 12 VA, VB, VC, VENABLE LOGIC-LEVEL THRESHOLD vs. VCC 3.0 MAX4581toc12 10 2.5 VA, VB, VC, VENABLE (V) THD (%) 60 40 20 0 OFF-LOSS PHASE (DEGREES) IEE 1 80 -30 -40 -50 -60 ICC -25 120 100 ON-LOSS -20 10 -50 MAX4581-09 0 -10 MAX4581/2/3-08 100 2.0 1.5 1.0 0.5 0 0 1 2 3 4 5 6 7 8 9 10 11 12 VCC (V) _______________________________________________________________________________________ 7 MAX4581/MAX4582/MAX4583 Typical Operating Characteristics (continued) (VCC = 5V, VEE = -5V, GND = 0V, TA = +25C, unless otherwise noted.) Low-Voltage, CMOS Analog Multiplexers/Switches MAX4581/MAX4582/MAX4583 Pin Description PIN MAX4581 MAX4582 MAX4583 NAME DIP, SO, TSSOP QFN DIP, SO, TSSOP QFN DIP, SO, TSSOP QFN 13, 14, 15, 12, 1, 5, 2, 4 11, 12, 13, 10, 15, 3, 16, 2 -- -- -- -- 3 1 13 11 14 -- -- 12, 14, 15, 11 10, 12, 13, 9 -- -- 1, 5, 2, 4 -- -- -- -- -- -- -- -- -- FUNCTION X0-X7 Analog Switch Inputs 0-7 12 X Analog Switch "X" Output -- -- X0, X1, X2, X3 Analog Switch "X" Inputs 0-3 15, 3, 16, 2 -- -- Y0, Y1, Y2, Y3 Analog Switch "Y" Inputs 0-3 3 1 15 13 Y Analog Switch "Y" Output -- -- 13 11 X1 Analog Switch "X" Normally Open Input -- -- 12 10 X0 Analog Switch "X" Normally Closed Input -- -- 1 15 Y1 Analog Switch "Y" Normally Open Input -- -- -- 2 16 Y0 Analog Switch "Y" Normally Open Input -- -- -- -- 3 1 Z1 Analog Switch "Z" Normally Open Input -- -- -- -- 5 3 Z0 Analog Switch "Z" Normally Open Input -- -- -- -- 4 2 Z Analog Switch "Z" Output 16 14 16 14 16 14 VCC 11 9 10 8 11 9 A Digital Address "A" Input 10 8 9 7 10 8 B Digital Address "B" Input 9 7 -- -- 9 7 C Digital Address "C" Input 8 6 8 6 8 6 GND Ground. Connect to digital ground. (Analog signals have no ground reference; they are limited to VCC and VEE.) 7 5 7 5 7 5 VEE Negative Analog Supply-Voltage Input. Connect to GND for single-supply operation. 6 4 6 4 6 4 ENABLE -- EP -- EP -- EP EP Positive Analog and Digital Supply-Voltage Input Digital Enable Input. Normally connected to GND. Exposed Pad. Connect EP to VCC. Note: Input and output pins are identical and interchangeable. Any may be considered an input or output; signals pass equally well in both directions. __________Applications Information Power-Supply Considerations Overview The MAX4581/MAX4582/MAX4583 construction is typical of most CMOS analog switches. They have three 8 supply pins: VCC, VEE, and GND. VCC and VEE are used to drive the internal CMOS switches and set the limits of the analog voltage on any switch. Reverse ESDprotection diodes are internally connected between each analog-signal pin and both VCC and VEE. If any analog signal exceeds VCC or VEE, one of these diodes _______________________________________________________________________________________ Low-Voltage, CMOS Analog Multiplexers/Switches MAX4581/MAX4582/MAX4583 Table 1. Truth Table/Switch Programming SELECT INPUTS ON SWITCHES ENABLE INPUT C* B A MAX4581 MAX4582 MAX4583 H X X X All switches open All switches open All switches open L L L L X-X0 X-X0, Y-Y0 X-X0, Y-Y0, Z-Z0 L L L H X-X1 X-X1, Y-Y1 X-X1, Y-Y0, Z-Z0 L L H L X-X2 X-X2, Y-Y2 X-X0, Y-Y1, Z-Z0 L L H H X-X3 X-X3, Y-Y3 X-X1, Y-Y1, Z-Z0 L H L L X-X4 X-X0, Y-Y0 X-X0, Y-Y0, Z-Z1 L H L H X-X5 X-X1, Y-Y1 X-X1, Y-Y0, Z-Z1 L H H L X-X6 X-X2, Y-Y2 X-X0, Y-Y1, Z-Z1 L H H H X-X7 X-X3, Y-Y3 X-X1, Y-Y1, Z-Z1 X = Don't care *C not present on MAX4582. Note: Input and output pins are identical and interchangeable. Either may be considered an input or output; signals pass equally well in either direction. will conduct. During normal operation, these and other reverse-biased ESD diodes leak, forming the only current drawn from VCC or VEE. Virtually all the analog leakage current comes from the ESD diodes. Although the ESD diodes on a given signal pin are identical and therefore fairly well balanced, they are reverse biased differently. Each is biased by either VCC or VEE and the analog signal. This means their leakages will vary as the signal varies. The difference in the two diode leakages to the VCC and VEE pins constitutes the analog-signal-path leakage current. All analog leakage current flows between each pin and one of the supply terminals, not to the other switch terminal. This is why both sides of a given switch can show leakage currents of either the same or opposite polarity. There is no connection between the analog-signal paths and GND. VCC and GND power the internal logic and logic-level translators, and set the input logic limits. The logic-level translators convert the logic levels into switched V CC and VEE signals to drive the gates of the analog signals. This drive signal is the only connection between the logic supplies and signals and the analog supplies. VCC and VEE have ESD-protection diodes to GND. The logic-level thresholds are TTL/CMOS compatible when VCC is +5V. As VCC rises, the threshold increases _______________________________________________________________________________________ 9 MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches slightly, so when VCC reaches +12V the threshold is about 3.1V (above the TTL-guaranteed high-level minimum of 2.8V, but still compatible with CMOS outputs). VCC D1 EXTERNAL BLOCKING DIODE Bipolar Supplies These devices operate with bipolar supplies between 2V and 5V. The VCC and VEE supplies need not be symmetrical, but their sum cannot exceed the +13V absolute maximum rating Single Supply These devices operate from a single supply between +2V and +12V when VEE is connected to GND. All of the bipolar precautions must be observed. At room temperature, they actually "work" with a single supply near or below +1.7V, although as supply voltage decreases, switch on-resistance and switching times become very high. Overvoltage Protection Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maximum ratings because stresses beyond the listed ratings can cause permanent damage to the devices. Always sequence VCC on first, then VEE, followed by the logic inputs and analog signals. If power-supply sequencing is not possible, add two small signal diodes (D1, D2) in series with the supply pins for overvoltage protection (Figure 1). Adding diodes reduces the analog-signal range to one diode drop below VCC and one diode drop above VEE, but does not affect the devices' low switch resistance and low leakage characteristics. Device operation is unchanged, and the difference between VCC and VEE should not exceed 13V. These protection diodes are not recommended when using a single supply if signal levels must extend to ground. High-Frequency Performance In 50 systems, signal response is reasonably flat up to 50MHz (see Typical Operating Characteristics). Above 20MHz, the on response has several minor peaks which are highly layout dependent. The problem is not turning the switch on, but turning it off. The offstate switch acts like a capacitor and passes higher frequencies with less attenuation. At 10MHz, off isolation is about -50dB in 50 systems, becoming worse (approximately 20dB per decade) as frequency increases. Higher circuit impedances also degrade off isolation. Adjacent channel attenuation is about 3dB above that of a bare IC socket and is entirely due to capacitive coupling. 10 MAX4581 MAX4582 MAX4583 VCC * * X, Y, Z X_, Y_, Z_ * * VEE D2 EXTERNAL BLOCKING DIODE VEE *INTERNAL PROTECTION DIODES Figure 1. Overvoltage Protection Using External Blocking Diodes Pin Nomenclature The MAX4581/MAX4582/MAX4583 are pin-compatible with the industry-standard 74HC4051/74HC4052/ 74HC4053 and the MAX4051/MAX4052/MAX4053. They function identically and have identical logic diagrams, although these parts differ electrically. The pin designations and logic diagrams in this data sheet conform to the original 1972 specifications published by RCA for the CD4051/CD4052/CD4053. These designations differ from the standard Maxim switch and mux designations as found all other Maxim data sheets (including the MAX4051/MAX4052/MAX4053) and may cause confusion. Designers who feel more comfortable with Maxim's standard designations are advised that the pin designations and logic diagrams on the MAX4051/MAX4052/MAX4053 data sheet may be freely applied to the MAX4581/MAX4582/MAX4583. ______________________________________________________________________________________ Low-Voltage, CMOS Analog Multiplexers/Switches VCC VA, VB, VC A 50 VA, VB, VC VCC X0 B VCC X1-X6 VX0 X7 ENABLE 90% VEE VOUT X GND 50% 0V C MAX4581 VCC VEE 0V VOUT 35pF 90% VX7 300 VEE tTRANS tTRANS VCC VA, VB VA, VB VCC A B X0, Y0 VCC VX0, VY0 MAX4582 X3, Y3 ENABLE 90% VEE X, Y GND 50% 0V X1, X2, Y1, Y2 50 VCC VOUT VEE 35pF 0V VOUT 90% VX3, VY3 300 VEE tTRANS tTRANS VCC VA, VB, VC VCC VA, VB, VC X1, Y1, Z1 A, B, C VEE 0V MAX4583 ENABLE GND VCC X, Y, Z VEE 35pF VEE 90% 0V VOUT 300 50% VX0, VY0, VZ0 50 X2, Y2, Z2 VCC VOUT 90% VX1, VY1, VZ1 tTRANS tTRANS VEE = 0V FOR SINGLE-SUPPLY OPERATION. TEST EACH SECTION INDIVIDUALLY. Figure 2. Address Transition Times ______________________________________________________________________________________ 11 MAX4581/MAX4582/MAX4583 ______________________________________________Test Circuits/Timing Diagrams MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches _________________________________Test Circuits/Timing Diagrams (continued) VCC A VEnable VCC X0 B VCC VCC 50% 0V X1-X7 VX0 C 90% MAX4581 VENABLE ENABLE VOUT X GND VEE 50 VOUT 90% 35pF 0V 300 VEE tOFF tON VCC A B VEnable VCC X0, Y0 VCC VCC 50% 0V X1-X3, Y1-Y3 VX0, VY0 90% MAX4582 VENABLE ENABLE X, Y GND VOUT VEE 50 35pF VOUT 90% 0V 300 VEE tOFF tON VCC A B C VCC VEnable X1, Y1, Z1 X0, Y0, Z0 ENABLE 0V VEE VX0, VY0, VZ0 X, Y, Z GND VOUT VEE 50 35pF 300 VEE 50% VCC MAX4583 VENABLE VCC 90% VOUT 90% VX1, VY1, VZ1 tON VEE = 0V FOR SINGLE-SUPPLY OPERATION. TEST EACH SECTION INDIVIDUALLY. Figure 3. Inhibit Switching Times 12 ______________________________________________________________________________________ tOFF Low-Voltage, CMOS Analog Multiplexers/Switches VCC VCC VA, VB, VC VA, VB VCC A X0-X7 B 50 VCC A VCC 50 X0-X3, Y0-Y3 B VCC C MAX4582 MAX4581 ENABLE VOUT X GND VEE ENABLE X, Y GND 35pF VOUT VEE 35pF 300 300 VEE VEE VCC VA, VB, VC VCC X0, X1, Y0, Y1, Z0, Z1 A, B, C tR < 20ns tF < 20ns V+ VA, VB, VC VCC 50% 0V 50 VX, VY, VZ MAX4583 ENABLE 80% X, Y, Z GND VOUT VEE 35pF 300 VEE VOUT 0V VEE = 0V FOR SINGLE-SUPPLY OPERATION. TEST EACH SECTION INDIVIDUALLY. tBBM Figure 4. Break-Before-Make Interval VCC VCC VCC X_, Y_, Z_ A CHANNEL SELECT VEnable 0V B C VENABLE MAX4581 MAX4582 MAX4583 ENABLE GND 50 X, Y, Z VEE VEE VEE = 0V FOR SINGLE-SUPPLY OPERATION. TEST EACH SECTION INDIVIDUALLY. VOUT VOUT VOUT CL = 1000pF VOUT IS THE MEASURED VOLTAGE DUE TO CHARGE TRANSFER ERROR Q WHEN THE CHANNEL TURNS OFF. Q = VOUT X CL Figure 5. Charge Injection ______________________________________________________________________________________ 13 MAX4581/MAX4582/MAX4583 _________________________________Test Circuits/Timing Diagrams (continued) MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches _________________________________Test Circuits/Timing Diagrams (continued) VCC 10nF VCC A CHANNEL SELECT VIN NETWORK ANALYZER 50 50 X_, Y_, Z_ OFF-ISOLATION = 20log VIN B C MAX4581 MAX4582 MAX4583 ENABLE GND ON-LOSS = 20log VOUT X, Y, Z VEE MEAS. REF. CROSSTALK = 20log 50 50 10nF VEE MEASUREMENTS ARE STANDARDIZED AGAINST SHORT AT SOCKET TERMINALS. OFF-ISOLATION IS MEASURED BETWEEN COM AND "OFF" NO TERMINAL ON EACH SWITCH. ON-LOSS IS MEASURED BETWEEN COM AND "ON" NO TERMINAL ON EACH SWITCH. CROSSTALK (MAX4582/MAX4583) IS MEASURED FROM ONE CHANNEL (A, B, C) TO ALL OTHER CHANNELS. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. Figure 6. Off Isolation, On Loss, and Crosstalk VCC A CHANNEL SELECT VCC X_, Y_, Z_ B C ENABLE MAX4581 MAX4582 MAX4583 GND X, Y, Z VEE 1MHz CAPACITANCE ANALYZER VEE Figure 7. Capacitance 14 VOUT ______________________________________________________________________________________ VOUT VIN VOUT VIN Low-Voltage, CMOS Analog Multiplexers/Switches BOTTOM VIEW X2 13 VCC 14 X1 X0 X3 A X1 X X0 X3 X X1 X0 A 12 11 10 9 12 11 10 9 12 11 10 9 8 B X2 13 7 C VCC 14 MAX4581 X4 15 X6 16 8 A Y 13 7 B VCC 14 MAX4582 *EP 6 GND Y0 15 5 VEE Y2 16 8 B 7 C 6 GND 5 VEE MAX4583 *EP 6 GND Y1 15 5 VEE Y0 16 *EP 1 2 3 4 1 2 3 4 1 2 3 4 X X7 X5 EN Y Y3 Y1 EN Z1 Z Z0 EN *CONNECT EXPOSED PAD TO V+ Ordering Information (continued) PINPACKAGE PKG CODE PART TEMP RANGE PINPACKAGE PKG CODE 0C to +70C 16 QSOP E16-4 MAX4582EEE -40C to +85 16 QSOP E16-4 0C to +70C Dice* -- MAX4582EGE -40C to +85 16 QFN - EP** 16 Plastic DIP P16-1 MAX4582ASE 0C to +70C 16 Narrow SO S16-2 -40C to +85C 16 Narrow SO S16-2 MAX4582AUE 0C to +70C 16 TSSOP U16-2 MAX4581EUE -40C to +85C 16 TSSOP U16-2 MAX4583CPE 0C to +70C 16 Plastic DIP P16-1 MAX4581EEE -40C to +85C 16 QSOP E16-4 MAX4583CSE 0C to +70C 16 Narrow SO S16-2 MAX4581EGE -40C to +85C 16 QFN - EP** G1644-1 MAX4583CUE 0C to +70C 16 TSSOP U16-2 MAX4581ASE 0C to +70C 16 Narrow SO S16-2 MAX4583CEE 0C to +70C 16 QSOP E16-4 MAX4581AUE 0C to +70C 16 TSSOP U16-2 MAX4583C/D 0C to +70C Dice* MAX4582CPE 0C to +70C 16 Plastic DIP P16-1 MAX4583EPE -40C to +85 16 Plastic DIP MAX4582CSE 0C to +70C 16 Narrow SO S16-2 MAX4583ESE -40C to +85 16 Narrow SO S16-2 MAX4582CUE 0C to +70C 16 TSSOP U16-2 MAX4583EUE -40C to +85 16 TSSOP U16-2 MAX4582CEE -40C to +85 16 QSOP E16-4 MAX4583EEE -40C to +85 16 QSOP E16-4 MAX4582C/D -40C to +85 Dice* -- MAX4583EGE -40C to +85 16 QFN - EP** MAX4582EPE -40C to +85 16 Plastic DIP P16-1 MAX4583ASE -40C to +125 16 Narrow SO S16-2 MAX4582ESE -40C to +85 16 Narrow SO S16-2 MAX4583AUE -40C to +125 16 TSSOP U16-2 MAX4582EUE -40C to +85 16 TSSOP U16-2 PART TEMP RANGE MAX4581CEE MAX4581C/D MAX4581EPE -40C to +85C MAX4581ESE G1644-1 -- P16-1 G1644-1 *Contact factory for availability. **EP = Exposed pad. ______________________________________________________________________________________ 15 MAX4581/MAX4582/MAX4583 Pin Configurations/Functional Diagrams (continued) ____Chip Topographies (continued) MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches __________________________________________________________Chip Topographies MAX4581 X6 X4 VCC MAX4582 X2 Y2 Y0 VCC X2 X1 X X1 Y N.C. X7 X Y3 X0 X5 X0 Y1 X3 X3 0.069" (1.75mm) 0.069" (1.75mm) A A Enable Enable VEE GND C 0.053" (1.35mm) VEE B GND B 0.053" (1.35mm) N.C. N.C. = NO CONNECTION TRANSISTOR COUNT: 219 SUBSTRATE CONNECTED TO V+. TRANSISTOR COUNT: 219 SUBSTRATE CONNECTED TO V+. MAX4583 Y0 Y1 VCC Y X Z1 N.C. Z X1 Z0 X0 0.069" (1.75mm) A Enable VEE GND C 0.053" (1.35mm) B N.C. = NO CONNECTION TRANSISTOR COUNT: 219 SUBSTRATE CONNECTED TO V+. 16 ______________________________________________________________________________________ Low-Voltage, CMOS Analog Multiplexers/Switches 32L QFN.EPS ______________________________________________________________________________________ 17 MAX4581/MAX4582/MAX4583 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) MAX4581/MAX4582/MAX4583 Low-Voltage, CMOS Analog Multiplexers/Switches Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) Revision History Pages changed at Rev 5: 1, 8, 15, 16, 18 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2007 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc. ENGLISH * ???? * ??? * ??? WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS MAX4582 Part Number Table Notes: 1. See the MAX4582 QuickView Data Sheet for further information on this product family or download the MAX4582 full data sheet (PDF, 524kB). 2. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales. 3. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day. 4. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full data sheet or Part Naming C onventions. 5. * Some packages have variations, listed on the drawing. "PkgC ode/Variation" tells which variation the product uses. Part Number Free Sample Buy Direct Package: TYPE PINS SIZE Temp RoHS/Lead-Free? Materials Analysis -40C to +85C RoHS/Lead-Free: Yes DRAWING CODE/VAR * MAX4582ETE+ MAX4582C /D RoHS/Lead-Free: No MAX4582C PE+ PDIP;16 pin;.300" Dwg: 21-0043D (PDF) Use pkgcode/variation: P16+1* 0C to +70C RoHS/Lead-Free: Yes Materials Analysis MAX4582C PE PDIP;16 pin;.300" Dwg: 21-0043D (PDF) Use pkgcode/variation: P16-1* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX4582EPE PDIP;16 pin;.300" Dwg: 21-0043D (PDF) Use pkgcode/variation: P16-1* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX4582C EE+T QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16+4* 0C to +70C RoHS/Lead-Free: Yes Materials Analysis MAX4582C EE+ QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16+4* 0C to +70C RoHS/Lead-Free: Yes Materials Analysis MAX4582C EE-T QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16-4* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX4582C EE QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16-4* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX4582EEE-T QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16-4* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX4582EEE+T QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16+4* -40C to +85C RoHS/Lead-Free: Yes Materials Analysis MAX4582EEE+ QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16+4* -40C to +85C RoHS/Lead-Free: Yes Materials Analysis MAX4582EEE QSOP;16 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E16-4* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX4582ASE+ SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16+2* -40C to +125C RoHS/Lead-Free: Yes Materials Analysis MAX4582ASE+T MAX4582ASE -40C to +125C RoHS/Lead-Free: Yes SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16-2* MAX4582ASE-T -40C to +125C RoHS/Lead-Free: No Materials Analysis -40C to +125C RoHS/Lead-Free: No MAX4582C SE+T SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16+2* 0C to +70C RoHS/Lead-Free: Yes Materials Analysis MAX4582C SE-T SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX4582C SE SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX4582C SE+ SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16+2* 0C to +70C RoHS/Lead-Free: Yes Materials Analysis MAX4582ESE+T SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16+2* -40C to +85C RoHS/Lead-Free: Yes Materials Analysis MAX4582ESE+ SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16+2* -40C to +85C RoHS/Lead-Free: Yes Materials Analysis MAX4582ESE-T SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX4582ESE SOIC ;16 pin;.150" Dwg: 21-0041B (PDF) Use pkgcode/variation: S16-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX4582AUE-T -40C to +125C RoHS/Lead-Free: No MAX4582AUE TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16-2* -40C to +125C RoHS/Lead-Free: No Materials Analysis MAX4582C UE TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX4582C UE-T TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX4582C UE+T TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16+2* 0C to +70C RoHS/Lead-Free: Yes Materials Analysis MAX4582C UE+ TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16+2* 0C to +70C RoHS/Lead-Free: Yes Materials Analysis MAX4582EUE+ TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16+2* -40C to +85C RoHS/Lead-Free: Yes Materials Analysis MAX4582EUE+T TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16+2* -40C to +85C RoHS/Lead-Free: Yes Materials Analysis MAX4582EUE-T TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX4582EUE TSSOP;16 pin;4.4mm Dwg: 21-0066I (PDF) Use pkgcode/variation: U16-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis Didn't Find What You Need? C ONTAC T US: SEND US AN EMAIL C opyright 2 0 0 7 by M axim I ntegrated P roduc ts , Dallas Semic onduc tor * Legal N otic es * P rivac y P olic y