Supertex inc. HV5530 32-Channel Serial to Parallel Converter With Open Drain Outputs Features Processed with HVCMOS technology Sink current minimum 100mA Shift register speed 8.0MHz Polarity and Blanking inputs CMOS compatible inputs Forward and reverse shifting options Diode to VPP allows efficient power recovery (R) General Description The HV5530 is a low-voltage serial to high-voltage parallel converter with open drain outputs. This device has been designed for use as a driver for AC-electroluminescent displays. It can also be used in any application requiring multiple output high voltage current sinking capabilities such as driving inkjet and electrostatic print heads, plasma panels, vacuum fluorescent, or large matrix LCD displays. This device consists of a 32-bit shift register, 32 latches, and control logic to perform the polarity select and blanking of the outputs. Data is shifted through the shift register on the high to low transition of the clock. The HV5530 shifts in the counter clockwise direction when viewed from the top of the package. A data output buffer is provided for cascading devices. This output reflects the current status of the last bit of the shift register. Operation of the shift register is not affected by the LE (latch enable), BL (blanking), or the POL (polarity) inputs. Transfer of data from the shift register to the latch occurs when the LE (latch enable) input is high. The data in the latch is stored when LE is low. Functional Block Diagram POL BL LE HVOUT1 DATA INPUT Latch HVOUT2 CLK Latch 32-Bit Shift Register (Outputs 3 to 30 not shown) HVOUT31 Latch HVOUT32 DATA OUTPUT Supertex inc. Latch 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com HV5530 Ordering Information Package Options Device 44-Lead Quad Plastic Gullwing 44-Lead Quad Plastic Chip Carrier HV5530PG-G HV5530PJ-G 10.00x10.00mm body 2.45mm height (max) 0.80mm pitch HV5530 .653x.653in body .180in height (max) .050in pitch -G indicates package is RoHS compliant (`Green') Pin Configurations Absolute Maximum Ratings Parameter Value Supply voltage, VDD 1 -0.5V to +15V Output voltage, VPP1 -0.5V to +315V Logic input levels -0.5V to VDD +0.5V 1 Ground current2 44 1 1.5A Continuous total power dissipation3 44-Lead PQFP (PG) 1200mW Operating temperature range (top view) 6 -40OC to +85OC Storage temperature range 1 44 40 -65OC to +150OC Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied. Continuous operation of the device at the absolute rating level may affect device reliability. All voltages are referenced to device ground. Notes: 1. All voltages are referenced to VSS 2. Duty cycle is limited by the total power dissipated in the package 3. For operation above 25C ambient derate linearly to maximum operating temperature at 20mW/C. 44-Lead PLCC (PJ) (top view) Product Marking Top Marking Recommended Operating Conditions YYWW HV5530PG LLLLLLLLL Sym Parameter Min Max Units VDD Logic voltage supply 10.8 13.2 V -0.3 +300 V HVOUT High voltage output VIH Input high voltage VDD -2.0 VDD V VIL Input low voltage 0 2.0 V fCLK Clock frequency TA Operating free-air temperature - 8.0 -40 +85 MHz C O Power-Up Sequence Bottom Marking CCCCCCCC AAA *May be part of top marking Package may or may not include the following marks: Si or 44-Lead PQFP (PG) Top Marking YYWW AAA HV5530PJ LLLLLLLLLL Bottom Marking Power-up sequence should be the following: 1. Connect ground 2. Apply VDD 3. Set all inputs to a known state YY = Year Sealed WW = Week Sealed L = Lot Number C = Country of Origin* A = Assembler ID* = "Green" Packaging CCCCCCCCCCC YY = Year Sealed WW = Week Sealed L = Lot Number A = Assembler ID C = Country of Origin* = "Green" Packaging *May be part of top marking Package may or may not include the following marks: Si or 44-Lead PLCC (PJ) Power-down sequence should be the reverse of the above. Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 2 HV5530 Electrical Characteristics (over recommended operating conditions unless otherwise noted) DC Characteristics Sym Parameter Min Max Units Conditions IDD VDD supply current - 15 mA fCLK = 8.0MHz, FDATA = 4.0MHz IDDQ VDD supply current (quiescent) - 100 A VIN = 0V Off state output current - 10 A All outputs high, all SWS parallel IIH High-level logic input current - 1.0 A VIH = VDD IIL Low-level logic input current - -1.0 A VIL = 0V VDD -1.0V - V IDOUT = -100A HVOUT - 15 V IHVOUT = +100mA DATA OUT - 1.0 V IDOUT = +100A - -1.5 V IOL = -100mA Min Max Units Conditions - 8.0 MHz --- IO(OFF) VOH High-level output data out VOL Low-level output voltage VOC HVOUT clamp voltage AC Characteristics Sym (VDD = 12V, TC = 25OC) Parameter fCLK Clock frequency tW Clock width, high or low 62 - ns --- tSU Data set-up time before CLK falls 25 - ns --- tH Data hold time after CLK falls 10 - ns --- tON Turn-on time, HVOUT from enable - 500 ns RL = 2.0K to VPP max. tDHL Delay time clock to data high to low - 100 ns CL = 15pF tDLH Delay time clock to data low to high - 100 ns CL = 15pF tDLE Delay time clock to LE low to high 50 - ns --- tWLE Width of LE pulse 50 - ns --- tSLE LE setup time before clock falls 50 - ns --- Input and Output Equivalent Circuits VDD VDD HVOUT DATA OUTPUT DATA INPUT HVIN VSS VSS VSS Logic Inputs Supertex inc. Logic Data Output High Voltage Outputs 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 3 HV5530 Switching Waveforms VIH DATA INPUT 50% Data Valid 50% tSU VIL tH VIH CLK 50% 50% 50% tWH 50% tWL VOH 50% DATA OUTPUT VOL tDLH VOH 50% VOL tDHL VIH 50% 50% LE tWLE tDLE HVOUT w/ S/R HIGH VIL VIL tSLE VOH 10% VOL tON Functional Table Inputs Function Outputs 1 2...32 Data Out * L * *...* On On...On * L H * *...* Off Off...Off * L H L * *...* * *...* * L H H H or L *...* * *...* * X H or L H H * *...* * *...* * X H or L H L * *...* * *...* * L H H H L *...* Off *...* * H H H H H *...* On *...* * LE BL POL All on X X X L All off X X X Invert mode X X Load S/R H or L Transparent latch mode HV Outputs 2...32 CLK Load latches Shift Reg 1 Data Notes: H = high level, L = low level, X = irrelevant, = high-to-low transition, = low-to-high transistion. * dependent on previous stage's state before the last CLK or last LE high. Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 4 HV5530 44-Lead PQFP Pin Assignment (PG) Pin # Function 1 HVOUT11 2 HVOUT12 3 HVOUT13 4 HVOUT14 5 HVOUT15 6 HVOUT16 7 HVOUT17 8 HVOUT18 9 HVOUT19 10 HVOUT20 11 HVOUT21 12 HVOUT22 13 HVOUT23 14 HVOUT24 15 HVOUT25 16 HVOUT26 17 HVOUT27 18 HVOUT28 19 HVOUT29 20 HVOUT30 21 HVOUT31 22 HVOUT32 23 DATA OUTPUT 24 N/C 25 N/C Description High voltage outputs. Data output pin. No connect. 26 N/C 27 POL Inverts the polarity of the HVOUT pins 28 CLK Clock pin, shift registers shifts data on falling edge of input clock. 29 VSS Reference voltage, usually ground. 30 VDD Logic supply voltage. 31 LE 32 DATA INPUT 33 BL Blanking pin sets all HVout pins low or high depending upon state of polarity. See function table. 34 N/C No connect. 35 HVOUT1 36 HVOUT2 37 HVOUT3 38 HVOUT4 39 HVOUT5 40 HVOUT6 41 HVOUT7 42 HVOUT8 43 HVOUT9 44 HVOUT10 Supertex inc. Latch enable pin, data is shifted from shift register to latches on logic input high. Data input pin. High voltage outputs. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 5 HV5530 44-Lead PLCC Pin Assignment (PJ) Pin # Function 1 HVOUT16 2 HVOUT17 3 HVOUT18 4 HVOUT19 5 HVOUT20 6 HVOUT21 7 HVOUT22 8 HVOUT23 9 HVOUT24 10 HVOUT25 11 HVOUT26 12 HVOUT27 13 HVOUT28 14 HVOUT29 15 HVOUT30 16 HVOUT31 17 HVOUT32 18 DATA OUTPUT 19 N/C 20 N/C Description High voltage outputs. Data output pin. No connect. 21 N/C 22 POL Inverts the polarity of the HVOUT pins 23 CLK Clock pin, shift registers shifts data on falling edge of input clock. 24 VSS Reference voltage, usually ground. 25 VDD Logic supply voltage. 26 LE 27 DATA INPUT 28 BL Blanking pin sets all HVout pins low or high depending upon state of polarity. See function table. 29 N/C No connect. 30 HVOUT1 31 HVOUT2 32 HVOUT3 33 HVOUT4 34 HVOUT5 35 HVOUT6 36 HVOUT7 37 HVOUT8 38 HVOUT9 39 HVOUT10 40 HVOUT11 41 HVOUT12 42 HVOUT13 43 HVOUT14 44 HVOUT15 Supertex inc. Latch enable pin, data is shifted from shift register to latches on logic input high. Data input pin. High voltage outputs. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 6 HV5530 44-Lead PQFP Package Outline (PG) 10.00x10.00mm body, 2.35mm height (max), 0.80mm pitch D D1 E E1 Note 1 (Index Area D1/4 x E1/4) 44 1 e b Top View View B A L2 A2 Seating Plane L A1 L1 Side View Gauge Plane Seating Plane View B Note: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. Symbol MIN Dimension NOM (mm) MAX A A1 A2 b D D1 E E1 1.95* 0.00 1.95 0.30 13.65* 9.80* 13.65* 9.80* - - 2.00 - 13.90 10.00 13.90 10.00 2.35 0.25 2.10 0.45 14.15* 10.20* 14.15* 10.20* e 0.80 BSC L 0.73 0.88 1.03 L1 1.95 REF L2 0.25 BSC JEDEC Registration MO-112, Variation AA-2, Issue B, Sep.1995. * This dimension is not specified in the JEDEC drawing. Drawings not to scale. Supertex Doc. #: DSPD-44PQFPPG, Version C041309. Supertex inc. 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 7 0O 3.5O 7O HV5530 44-Lead PLCC Package Outline (PJ) .653x.653in body, .180in height (max), .050in pitch D D1 1 44 .048/.042 x 45O 6 .150 MAX .056/.042 x 45O 40 Note 1 (Index Area) .075 MAX E1 E Note 2 .020max (3 Places) Top View Vertical Side View View B A Base Plane A2 Seating Plane e A1 b1 .020 MIN b Horizontal Side View R View B Notes: 1. A Pin 1 identifier must be located in the index area indicated. The Pin 1 identifier can be: a molded mark/identifier; an embedded metal marker; or a printed indicator. 2. Actual shape of this feature may vary. Symbol Dimension (inches) A A1 A2 b b1 D D1 E E1 MIN .165 .090 .062 .013 .026 .685 .650 .685 .650 NOM .172 .105 - - - .690 .653 .690 .653 MAX .180 .120 .083 .021 .036 .695 .656 .695 .656 e .050 BSC R .025 .035 .045 JEDEC Registration MS-018, Variation AC, Issue A, June, 1993. This dimension differs from the JEDEC drawing. Drawings not to scale. Supertex Doc. #: DSPD-44PLCCPJ, Version F031111. (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to http://www. supertex.com/packaging.html.) Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate "product liability indemnification insurance agreement." Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship. No responsibility is assumed for possible omissions and inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications refer to the Supertex inc. (website: http//www.supertex.com) Supertex inc. (c)2011 Supertex inc. All rights reserved. Unauthorized use or reproduction is prohibited. Doc.# DSFP-HV5530 B080411 1235 Bordeaux Drive, Sunnyvale, CA 94089 Tel: 408-222-8888 www.supertex.com 8