T PL IA N M CO *R oH S Features Applications Superior circuit protection Voice / VDSL cards Overcurrent and overvoltage protection Protection modules and dongles Blocks surges up to rated limits Process control equipment High-speed performance Test and measurement equipment Small SMT package General electronics Agency listing: TBU-CA Series - TBU(R) High-Speed Protectors General Information Agency Listing The TBU-CA Series of Bourns(R) TBU(R) Line In/ products are low capacitance single Line Out bidirectional high-speed protection components, constructed using MOSFET semiconductor technology, and designed to protect against faults caused by short circuits, AC power cross, induction and lightning surges. Line Out/ Line In UL Description File Number: E315805 TBU(R) Device The TBU(R) high-speed protector placed in the system circuit will monitor the current with the MOSFET detection circuit triggering to provide an effective barrier behind which sensitive electronics will not be exposed to large voltages or currents during surge events. The TBU(R) device is provided in a surface mount DFN package and meets industry standard requirements such as RoHS and Pb Free solder Absolute Maximum Ratings (@ TA = 25 C Unless Otherwise Noted) Symbol Parameter Vimp Peak impulse voltage withstand with duration less than 10 ms Vrms Continuous A.C. RMS voltage Top Tstg Tjmax ESD Operating temperature range Storage temperature range Maximum Junction Temperature HBM ESD protection per IEC 61000-4-2 Part Number TBU-CA025-xxx-WH TBU-CA040-xxx-WH TBU-CA050-xxx-WH TBU-CA065-xxx-WH TBU-CA085-xxx-WH TBU-CA025-xxx-WH TBU-CA040-xxx-WH TBU-CA050-xxx-WH TBU-CA065-xxx-WH TBU-CA085-xxx-WH Tel: +886-2 2562-4117 * Fax: +886-2 2562-4116 EMEA: Tel: +36 88 520 390 * Fax: +36 88 520 211 The Americas: Tel: +1-951 781-5500 * Fax: +1-951 781-5700 www.bourns.com WARNING Cancer and Reproductive Harm - www.P65Warnings.ca.gov * RoHS Directive 2002/95/EC Jan. 27, 2003 including annex and RoHS Recast 2011/65/EU June 8, 2011. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf Value 250 400 500 650 850 100 200 250 300 425 -55 to +125 -65 to +150 +125 2 Unit V V C C C kV TBU-CA Series - TBU(R) High-Speed Protectors Electrical Characteristics (@ TA = 25 C Unless Otherwise Noted) Symbol Itrigger Rdevice tblock Parameter Part Number Min. Typ. Max. Unit Current required for the device to go from operating state to protected state TBU-CAxxx-050-WH TBU-CAxxx-100-WH TBU-CAxxx-200-WH TBU-CAxxx-300-WH TBU-CAxxx-500-WH 50 100 200 300 500 75 150 300 450 750 100 200 400 600 1000 mA Series resistance of the TBU device Vimp = 250 V Vimp = 250 V Vimp = 250 V Vimp = 250 V Vimp = 250 V Itrigger (min.) = 50 mA Itrigger (min.) = 100 mA Itrigger (min.) = 200 mA Itrigger (min.) = 300 mA Itrigger (min.) = 500 mA TBU-CA025-050-WH TBU-CA025-100-WH TBU-CA025-200-WH TBU-CA025-300-WH TBU-CA025-500-WH 13.3 7.1 4.2 3.2 2.6 15.3 8.2 4.8 3.8 3.0 Vimp = 400 V Vimp = 400 V Vimp = 400 V Vimp = 400 V Vimp = 400 V Itrigger (min.) = 50 mA Itrigger (min.) = 100 mA Itrigger (min.) = 200 mA Itrigger (min.) = 300 mA Itrigger (min.) = 500 mA TBU-CA040-050-WH TBU-CA040-100-WH TBU-CA040-200-WH TBU-CA040-300-WH TBU-CA040-500-WH 14.3 8.1 5.2 4.3 3.6 16.5 9.4 6.0 5.0 4.2 Vimp = 500 V Vimp = 500 V Vimp = 500 V Vimp = 500 V Vimp = 500 V Itrigger (min.) = 50 mA Itrigger (min.) = 100 mA Itrigger (min.) = 200 mA Itrigger (min.) = 300 mA Itrigger (min.) = 500 mA TBU-CA050-050-WH TBU-CA050-100-WH TBU-CA050-200-WH TBU-CA050-300-WH TBU-CA050-500-WH 15.7 9.5 6.6 5.6 5.0 18.0 10.9 7.5 6.5 5.7 Vimp = 650 V Vimp = 650 V Vimp = 650 V Vimp = 650 V Vimp = 650 V Itrigger (min.) = 50 mA Itrigger (min.) = 100 mA Itrigger (min.) = 200 mA Itrigger (min.) = 300 mA Itrigger (min.) = 500 mA TBU-CA065-050-WH TBU-CA065-100-WH TBU-CA065-200-WH TBU-CA065-300-WH TBU-CA065-500-WH 17.7 11.5 8.6 7.6 7.0 20.3 13.2 9.8 8.8 8.0 Vimp = 850 V Vimp = 850 V Vimp = 850 V Vimp = 850 V Vimp = 850 V Itrigger (min.) = 50 mA Itrigger (min.) = 100 mA Itrigger (min.) = 200 mA Itrigger (min.) = 300 mA Itrigger (min.) = 500 mA TBU-CA085-050-WH TBU-CA085-100-WH TBU-CA085-200-WH TBU-CA085-300-WH TBU-CA085-500-WH 21.4 15.2 12.3 11.3 10.7 24.5 17.4 14.0 13.0 12.2 Time for the device to go from normal operating state to protected state (R) 1 s IQ Current through the triggered TBU device with 50 Vdc circuit voltage Vreset Voltage below which the triggered TBU(R) device will transition to normal operating state Rth(j-l) Junction to package pads - FR4 using recommended pad layout 98 C/W Rth(j-l) Junction to package pads - FR4 using heat sink on board (6 cm2) (1 in2) 40 C/W 0.25 0.50 1.00 mA 12 16 20 V Environmental Characteristics Parameter Moisture Sensitivity Level Value 1 1B Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf. TBU-CA Series - TBU(R) High-Speed Protectors Reference Application Basic TBU Operation (R) The TBU devices are general use protectors used in a wide variety of applications. The maximum voltage rating of the TBU(R) device should never be exceeded. Where necessary, an OVP should be employed to limit the maximum voltage. A costeffective protection solution combines Bourns(R) TBU(R) protection devices with a pair of Bourns(R) MOVs. For bandwidth sensitive applications, a Bourns(R) GDT may be substituted for the MOV. Line In / Line Out Line Out / Line In Equip. Line TBU (R) Device OVP TBU (R) Device OVP Line In / Line Out Line Out / Line In The TBU(R) device, constructed using MOSFET semiconductor technology, placed in the system circuit will monitor the current with the MOSFET detection circuit triggering to provide an effective barrier behind which sensitive electronics are not exposed to large voltages or currents during surge events. The TBU(R) exceeds the TBU(R) trigger. When operated, the TBU(R) device will limit the current to less than the Itrigger value within the tblock duration. If voltage above Vreset is continuously sustained, the TBU(R) device will subsequently reduce the current to a quiescent current level within a period of time that is dependent upon the applied voltage. After the surge, the TBU(R) device resets when the voltage across the TBU(R) device falls to the Vreset level. The TBU(R) device will automatically reset on lines which have no DC bias or have DC bias below Vreset (such as unpowered signal lines). Line If the line has a normal DC bias above Vreset, the voltage across the TBU(R) device may not fall below Vreset after the surge. In such cases, special care needs to be taken to ensure that the TBU(R) device will reset, with software monitoring as one method used to accomplish this. Bourns application engineers can provide further assistance. Performance Graphs Typical V-I Characteristics (TBU-CA050-300-WH) Typical Trigger Current vs. Temperature 1.8 ITRIP Normalized Trip Current 1.6 CURRENT (100 mA/div) VRESET VOLTAGE (5 V/div) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -75 -50 -25 0 25 50 75 100 125 150 Junction Temperature (C) Power Derating Curve Typical Resistance vs. Temperature 2.2 3.0 No Additional PCB Cu 0.5 sq. in. Additional PCB Cu 2.0 1.8 Normalized Resistance Total Max. Power (W) 2.5 2.0 1.5 1.0 0.5 0.0 20 40 60 80 100 Junction Temperature (C) 120 140 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 -75 -50 -25 0 25 50 75 100 125 150 Junction Temperature (C) Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf. TBU-CA Series - TBU(R) High-Speed Protectors Product Dimensions 0.70 (.028) 0.80 (.031) 0.70 (.028) 1.85 (.073) 0.30 (.012) 6.50 0.10 (.256 .004) XXXXX YWWLL 4.00 0.10 (.157 .004) PIN 1 & BACKSIDE CHAMFER SEATING PLANE DIMENSIONS: 1.85 (.073) 3.40 (.134) A= A1 = 0.80 - 1.00 (.031 - .039) 0.00 - 0.05 (.000 - .002) MM (INCHES) 0.30 (.012) C 0.25 PIN 1 (.010) Pad Designation Pad # Pin Out 1 Line In/Out 2 NU 3 Line Out/In Recommended Pad Layout TBU(R) High-Speed Protectors have a 100 % matte-tin termination uses PCB copper areas which extend beyond the exposed solder which matches the pad layout of the TBU(R) device in size and spacing. It is recommended that they should be the same dimension as the TBU(R) pads but if smaller solder pads are used, they should be centered on the TBU(R) package terminal pads and not more than 0.10-0.12 mm (0.004-0.005 in.) smaller in overall width or length. Solder pad areas should not be larger than the TBU(R) pad sizes to ensure adequate clearance is maintained. The recommended stencil thickness is 0.10-0.12 mm (0.004-0.005 in.) with a stencil opening size 0.025 mm (0.0010 in.) less than the solder pad size. 3 2 1 the junction to ambient thermal resistance, resulting in operation ability. All pads should soldered to the PCB, including pads marked as NC or NU but no electrical connection should be made to these pads. For minimum parasitic capacitance, it is recommended that signal, ground or power signals are not routed beneath any pad. Dark grey areas show added PCB copper area for better thermal resistance. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf. TBU-CA Series - TBU(R) High-Speed Protectors Average Ramp-Up Rate (Tsmax to Tp) Preheat - Temperature Min. (Tsmin) - Temperature Max. (Tsmax) - Time (tsmin to tsmax) Time maintained above: - Temperature (TL) - Time (tL) Time within 5 C of Actual Peak Temp. (tp) Ramp-Down Rate Time 25 C to Peak Temperature Pb-Free Assembly 3 C/sec. max. 150 C 200 C 60-180 sec. 217 C 60-150 sec. 260 C 20-40 sec. 6 C/sec. max. 8 min. max. How to Order Typical Part Marking TBU - CA 085 - 500 - WH Series CA = Bi-Series Impulse Voltage Rating 025 = 250 V 040 = 400 V 050 = 500 V 065 = 650 V 085 = 850 V Trigger Current 050 = 50 mA 100 = 100 mA 200 = 200 mA 300 = 300 mA 500 = 500 mA W = Hold to Trip Ratio 5 DIGIT PRODUCT CODE: * 1ST ALPHA CHARACTER INDICATES PRODUCT FAMILY: A = TBU-CA SERIES * 2ND & 3RD DIGITS INDICATE IMPULSE VOLTAGE. * 4TH & 5TH DIGITS INDICATE TRIGGER CURRENT. MANUFACTURER'S TRADEMARK TBU(R) Product XXXXX YWWLL PIN 1 MANUFACTURING DATE CODE: * 1ST DIGIT INDICATES THE YEAR. * 2ND & 3RD DIGITS INDICATE THE WEEK NUMBER. * 4TH & 5TH DIGITS INDICATE LOT CODE. Thermal Resistance vs Additional PCB Cu Area H = DFN Package Thermal Resistance (C/W) 120 100 80 60 40 20 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 Added Cu Area (Sq. In.) Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf. TBU-CA Series - TBU(R) High-Speed Protectors P0 D t B E P2 F A W N XXXXX YWWLL C D B0 R K0 D1 A0 P G (MEASURED AT HUB) EMBOSSMENT The type of corner on carrier will vary at different assembly sites. USER DIRECTION OF FEED QUANTITY: 3000 PIECES PER REEL A Min. 326 (12.835) B Max. 330 (13.002) Min. 1.5 (.059) A0 Min. 4.3 (.169) B0 Max. 4.5 (.177) Min. 6.7 (.264) Max. 1.2 (.047) Min. 7.9 (.311) K0 Min. 1.0 (.039) C Max. 2.5 (.098) Min. 12.8 (.504) D Max. 13.5 (.531) D Max. 6.9 (.272) Min. 1.5 (.059) Max. 8.1 (.319) Min. 3.9 (.159) P Min. 20.2 (.795) - D1 Max. 1.6 (.063) Min. 1.5 (.059) Max. 4.1 (.161) Min. 1.9 (.075) P0 G Ref. 16.5 (.650) Max. E Max. - Min. 1.65 (.065) P2 F Max. 1.85 (.073) Min. 7.4 (.291) Max. 0.5 (.020) Min. 0.25 (.010) R Max. 2.1 (.083) Min. 0 (0) N Ref. 102 (4.016) max. 7.6 (.299) t Max. 0.35 (.014) W Min. 15.7 (.618) Max. 16.3 (.642) DIMENSIONS: MM (INCHES) REV. 03/18 "TBU" is a registered trademark of Bourns, Inc. in the United States and other countries. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific disclaimers as set forth on the last page of this document, and at www.bourns.com/legal/disclaimer.pdf. Legal Disclaimer Notice This legal disclaimer applies to purchasers and users of Bourns(R) products manufactured by or on behalf of Bourns, Inc. and P[ZHSPH[LZJVSSLJ[P]LS)V\YUZ Unless otherwise expressly indicated in writing, Bourns(R) products and data sheets relating thereto are subject to change ^P[OV\[UV[PJL<ZLYZZOV\SKJOLJRMVYHUKVI[HPU[OLSH[LZ[YLSL]HU[PUMVYTH[PVUHUK]LYPM[OH[Z\JOPUMVYTH[PVUPZJ\YYLU[ and complete before placing orders for Bourns(R) products. The characteristics and parameters of a Bourns(R) product set forth in its data sheet are based on laboratory conditions, and statements regarding the suitability of products for certain types of applications are based on Bourns' knowledge of typical requirements in generic applications. The characteristics and parameters of a Bourns(R)WYVK\J[PUH\ZLYHWWSPJH[PVUTH]HY MYVT[OLKH[HZOLL[JOHYHJ[LYPZ[PJZHUKWHYHTL[LYZK\L[VP[OLJVTIPUH[PVUVM[OL)V\YUZ(R) product with other components PU[OL\ZLYZHWWSPJH[PVUVYPP[OLLU]PYVUTLU[VM[OL\ZLYHWWSPJH[PVUP[ZLSM;OLJOHYHJ[LYPZ[PJZHUKWHYHTL[LYZVMH)V\YUZ(R) WYVK\J[HSZVJHUHUKKV]HYPUKPLYLU[HWWSPJH[PVUZHUKHJ[\HSWLYMVYTHUJLTH]HYV]LY[PTL<ZLYZZOV\SKHS^HZ]LYPM the actual performance of the Bourns(R)WYVK\J[PU[OLPYZWLJPAJKL]PJLZHUKHWWSPJH[PVUZHUKTHRL[OLPYV^UPUKLWLUKLU[ Q\KNTLU[ZYLNHYKPUN[OLHTV\U[VMHKKP[PVUHS[LZ[THYNPU[VKLZPNUPU[V[OLPYKL]PJLVYHWWSPJH[PVU[VJVTWLUZH[LMVY KPLYLUJLZIL[^LLUSHIVYH[VYHUKYLHS^VYSKJVUKP[PVUZ <USLZZ)V\YUZOHZL_WSPJP[SKLZPNUH[LKHUPUKP]PK\HS)V\YUZ(R) product as meeting the requirements of a particular industry Z[HUKHYKLN0:6;: VYHWHY[PJ\SHYX\HSPAJH[PVULN<3SPZ[LKVYYLJVNUPaLK)V\YUZPZUV[YLZWVUZPISLMVYHU MHPS\YLVMHUPUKP]PK\HS)V\YUZ(R)WYVK\J[[VTLL[[OLYLX\PYLTLU[ZVMZ\JOPUK\Z[YZ[HUKHYKVYWHY[PJ\SHYX\HSPAJH[PVU<ZLYZ of Bourns(R) products are responsible for ensuring compliance with safety-related requirements and standards applicable to [OLPYKL]PJLZVYHWWSPJH[PVUZ Bourns(R)WYVK\J[ZHYLUV[YLJVTTLUKLKH\[OVYPaLKVYPU[LUKLKMVY\ZLPUU\JSLHYSPMLZH]PUNSPMLJYP[PJHSVYSPMLZ\Z[HPUPUN HWWSPJH[PVUZUVYPUHUV[OLYHWWSPJH[PVUZ^OLYLMHPS\YLVYTHSM\UJ[PVUTHYLZ\S[PUWLYZVUHSPUQ\YKLH[OVYZL]LYLWYVWLY[ VYLU]PYVUTLU[HSKHTHNL<USLZZL_WYLZZSHUKZWLJPAJHSSHWWYV]LKPU^YP[PUNI[^VH\[OVYPaLK)V\YUZYLWYLZLU[H[P]LZ on a case-by-case basis, use of any Bourns(R)WYVK\J[ZPUZ\JO\UH\[OVYPaLKHWWSPJH[PVUZTPNO[UV[ILZHMLHUK[O\ZPZH[ [OL\ZLYZZVSLYPZR3PMLJYP[PJHSHWWSPJH[PVUZPUJS\KLKL]PJLZPKLU[PALKI[OL<:-VVKHUK+Y\N(KTPUPZ[YH[PVUHZ*SHZZ000 KL]PJLZHUKNLULYHSSLX\P]HSLU[JSHZZPAJH[PVUZV\[ZPKLVM[OL<UP[LK:[H[LZ )V\YUZL_WYLZZSPKLU[PALZ[OVZL)V\YUZ(R)Z[HUKHYKWYVK\J[Z[OH[HYLZ\P[HISLMVY\ZLPUH\[VTV[P]LHWWSPJH[PVUZVUZ\JO WYVK\J[ZKH[HZOLL[ZPU[OLZLJ[PVULU[P[SLK(WWSPJH[PVUZ<USLZZL_WYLZZSHUKZWLJPAJHSSHWWYV]LKPU^YP[PUNI[^V H\[OVYPaLK)V\YUZYLWYLZLU[H[P]LZVUHJHZLIJHZLIHZPZ\ZLVMHUV[OLY)V\YUZ(R)Z[HUKHYKWYVK\J[ZPUHUH\[VTV[P]L HWWSPJH[PVUTPNO[UV[ILZHMLHUK[O\ZPZUV[YLJVTTLUKLKH\[OVYPa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ourns(R)Z[HUKHYKWYVK\J[ZHYLUV[[LZ[LK[VJVTWS^P[O<UP[LK:[H[LZ-LKLYHS(]PH[PVU(KTPUPZ[YH[PVUZ[HUKHYKZNLULYHSS VYHUV[OLYNLULYHSSLX\P]HSLU[NV]LYUTLU[HSVYNHUPaH[PVUZ[HUKHYKHWWSPJHISL[VWYVK\J[ZKLZPNULKVYTHU\MHJ[\YLKMVY \ZLPUHPYJYHM[VYZWHJLHWWSPJH[PVUZ)V\YUZL_WYLZZSPKLU[PALZ)V\YUZ(R) standard products that are suitable for use in aircraft VYZWHJLHWWSPJH[PVUZVUZ\JOWYVK\J[ZKH[HZOLL[ZPU[OLZLJ[PVULU[P[SLK(WWSPJH[PVUZ<USLZZL_WYLZZSHUKZWLJPAJHSS HWWYV]LKPU^YP[PUNI[^VH\[OVYPaLK)V\YUZYLWYLZLU[H[P]LZVUHJHZLIJHZLIHZPZ\ZLVMHUV[OLY)V\YUZ(R) standard WYVK\J[PUHUHPYJYHM[VYZWHJLHWWSPJH[PVUTPNO[UV[ILZHMLHUK[O\ZPZUV[YLJVTTLUKLKH\[OVYPaLKVYPU[LUKLKHUKPZH[ the user's sole risk. ;OL\ZLHUKSL]LSVM[LZ[PUNHWWSPJHISL[V)V\YUZ(R) custom products shall be negotiated on a case-by-case basis by Bourns and the user for which such Bourns(R)J\Z[VTWYVK\J[ZHYLZWLJPHSSKLZPNULK(IZLU[H^YP[[LUHNYLLTLU[IL[^LLU)V\YUZ HUK[OL\ZLYYLNHYKPUN[OL\ZLHUKSL]LSVMZ\JO[LZ[PUN[OLHIV]LWYV]PZPVUZHWWSPJHISL[V)V\YUZ(R) standard products shall also apply to such Bourns(R) custom products. Users shall not sell, transfer, export or re-export any Bourns(R)WYVK\J[ZVY[LJOUVSVNMVY\ZLPUHJ[P]P[PLZ^OPJOPU]VS]L[OL KLZPNUKL]LSVWTLU[WYVK\J[PVU\ZLVYZ[VJRWPSPUNVMU\JSLHYJOLTPJHSVYIPVSVNPJHS^LHWVUZVYTPZZPSLZUVYZOHSS[OL\ZL Bourns(R)WYVK\J[ZVY[LJOUVSVNPUHUMHJPSP[^OPJOLUNHNLZPUHJ[P]P[PLZYLSH[PUN[VZ\JOKL]PJLZ;OLMVYLNVPUNYLZ[YPJ[PVUZ HWWS[VHSS\ZLZHUKHWWSPJH[PVUZ[OH[]PVSH[LUH[PVUHSVYPU[LYUH[PVUHSWYVOPIP[PVUZPUJS\KPUNLTIHYNVZVYPU[LYUH[PVUHS YLN\SH[PVUZ-\Y[OLY)V\YUZ(R) products and Bourns technology and technical data may not under any circumstance be exported or re-exported to countries subject to international sanctions or embargoes. Bourns(R) products may not, without WYPVYH\[OVYPa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bilingual versions are available at: Web Page: http://www.bourns.com/legal/disclaimers-terms-and-policies PDF: http://www.bourns.com/docs/Legal/disclaimer.pdf *9