KPS1015 - TDK-Lambda - Datasheet.Directory

KPS5,KPS10,KPS15Handbook Part Number 17165

Input Parameters

Output Limitations

Adjusting output voltage beyond the stated range may cause the overvoltage protection (OVP)

to operate, whereby the output will cycle on and off or latch off. To reset for normal operation

simply adjust the potentiometer to reduce the ouput voltage to within it’s range or cycle the

input off then on if the unit has latched off.

RATED INPUT VOLTAGE RANGE 100 - 240V AC

INPUT FREQUENCY 47- 63Hz

RATED INPUT CURRENT 1.5A

INRUSH CURRENT (132/264VAC) 25/50 (COLD START)

Outputs

Servicing

These products are not customer serviceable. Repairs may only be carried out by Lambda UK or their

authorised agents. These products are not authorised for use as critical components in nuclear control

systems, life support systems or equipment for use in hazardous environments without the express

written approval of the Managing Director of Coutant Lambda Ltd.

Approval Limitations: Use in North America (AC units only)

When this product is used on 180VAC-250VAC mains with no neutral, connect the two live wires to

L(live) and N (neutral) terminals on the input connector. In this instance double pole fusing is required.

High Voltage Warning

Dangerous voltages present within the power supply. The proffesional installer must protect service

personnel from inadvertant contact with these dangerous voltages in the end equipment.

Important safety instructions

UL60950 and CSA 60950 EN60950,Class II and CE (LVD) mark.

Operation

Temperature: 0 to +700C ( >400C -700C derate at 2.5%/0C )

Humidity: 10 to 95% RH, non-condensing

Storage and Transportation

Temperature: -200C to +850C

Humidity: 10% to 95% RH, non-condensing

Shock

<196.1 m/s 2 (20G)

Vibration

23.52 m/s 2 (10-55HZ): constant sweep 1 min X , Y, Z for one hour)

Cooling

Convection

Models

Model Output Voltage (V) Output Current (A)

KPS5-3R3 3.3 1.25

KPS5-5 5.0 1.00

KPS5-12 12.0 0.42

KPS5-15 15.0 0.33

KPS5-24 24.0 0.23

KPS10-3R3 3.3 2.50

KPS10-5 5.0 2.00

KPS10-12 12.0 0.84

KPS10-15 15.0 0.67

KPS10-24 24.0 0.42

KPS15-3R3 3.3 3.00

KPS15-5 5.0 3.00

KPS15-12 12.0 1.25

KPS15-15 15.0 1.00

KPS15-24 24.0 0.63

Conducted and Radiated EMI

EN55022-B, FCC Class B

Immunity

EN61000-4-2,EN61000-4-3,EN6100-4-4,EN61000-4-6, EN61000-4-8

Output Parameters

Safety approvals

Environmental parameters

The ZP family of component power supplies is designed for use within other equipment or

enclosures which restrict access to authorised competent personnel only. For safe installation and

operation of this product, carefully follow the instructions listed below.

i) These products are supplied open frame

ii) These products are Class II and must be installed in accordance with Class II requirements of

IE/EN/UL/CSAC60950.

iii) These products are IPX0, and therefore chemicals/solvents, cleaning agents and other liquids

must not be used.

General installation instructions

Dielectric Strength testing is carried out as follows:

Primary mains circuit to earth - 1.5kVAC.Primary mains circuits to secondary -3kVAC.

Outputs to each other and to earth are isolated to 500VAC.

Level of insulation

Safety Class of Protection

These products are designed for the following parameters : Material Group IIIa, Pollution Degree 2,

Overvoltage Category II, Class II, Indoor use as part of an overall equipment such that the product is

accessible to service engineers only.

Fuse Information

Internal fuse (F1): T2.2AL, 250V

(Neutral)

(Live)

(Neutral)

(Live)

Input Connector

(Neutral)

(Live)