www.ti.com
FEATURES
SN54ABT16245A. . . WD PACKAGE
SN74ABT16245A. . . DGG, DGV, OR DL PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
1DIR
1B1
1B2
GND
1B3
1B4
VCC
1B5
1B6
GND
1B7
1B8
2B1
2B2
GND
2B3
2B4
VCC
2B5
2B6
GND
2B7
2B8
2DIR
1OE
1A1
1A2
GND
1A3
1A4
VCC
1A5
1A6
GND
1A7
1A8
2A1
2A2
GND
2A3
2A4
VCC
2A5
2A6
GND
2A7
2A8
2OE
DESCRIPTION
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300G – MARCH 1994 – REVISED JANUARY 2006
•Members of the Texas InstrumentsWidebus™ Family•State-of-the-Art EPIC-IIB™ BiCMOS DesignSignificantly Reduces Power Dissipation•Typical V
OLP
(Output Ground Bounce) <1 V atV
CC
= 5 V, T
A
= 25 °C•High-Impedance State During Power Up andPower Down•Distributed V
CC
and GND Pin ConfigurationMinimizes High-Speed Switching Noise•Flow-Through Architecture Optimizes PCBLayout
•High-Drive Outputs (–32-mA I
OH
, 64-mA I
OL
)•Latch-Up Performance Exceeds 500 mA PerJESD 70•ESD Protection Exceeds 2000 V PerMIL-STD-883, Method 3015; Exceeds 200 VUsing Machine Model (C = 200 pF, R = 0)•Package Options Includes Plastic Thin VerySmall-Outline (DGV), Shrink Small-Outline(DL), and Thin Shrink Small-Outline (DGG)Packages and 380-mil Fine-Pitch Ceramic(WD) Flat Package Using 25-milCenter-to-Center Spacings
The 'ABT16245A devices are 16-bit noninverting 3-state transceivers designed for synchronous two-waycommunication between data buses. The control-function implementation minimizes external timingrequirements.
These devices can be used as two 8-bit transceviers or one 16-bit transceiver. They allow data transmission fromthe A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR)input. The output-enable ( OE) input can be used to disable the device so that the buses are effectively isolated.
When V
CC
is between 0 and 2.1 V, the device is in the high-impedance state during power up or power down.However, to ensure the high-impendance state above 2.1 V, OE should be tied to V
CC
through a pullup resistor;the minimum value of the resistor is determined by the current-sinking capability of the driver.
The SN54ABT16245A is characterized for operation over the full military temperature range of –55 °C to 125 °C.The SN74ABT16245A is characterized for operation from –40 °C to 85 °C.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of TexasInstruments semiconductor products and disclaimers thereto appears at the end of this data sheet.Widebus, EPIC-IIB are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Copyright © 1994–2006, Texas Instruments IncorporatedProducts conform to specifications per the terms of the Texas
On products compliant to MIL-PRF-38535, all parameters areInstruments standard warranty. Production processing does not
tested unless otherwise noted. On all other products, productionnecessarily include testing of all parameters.
processing does not necessarily include testing of all parameters.
www.ti.com
1A2 46
1A3 44
1A4 43
1A5 41
1A6 40
1A7 38
1A8 37
2A2 35
2A3 33
2A4 32
2A5 30
2A6 29
2A7 27
2A8 26
1OE
2OE
1A1 47
G3
48
3 EN1 [BA]
1
1DIR 3 EN2 [AB]
G6
25
6 EN4 [BA]
24
2DIR 6 EN5 [AB]
1B1
2
1B2
3
1B3
5
1B4
6
1B5
8
1B6
9
1B7
11
1B8
12
2A1 36 2B1
13
2B2
14
2B3
16
2B4
17
2B5
19
2B6
20
2B7
22
2B8
23
1
2
4
5
SN54ABT16245A, SN74ABT16245A16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300G – MARCH 1994 – REVISED JANUARY 2006
FUNCTION TABLE(EACH 8-BIT SECTION)
INPUTS
OPERATIONOE DIR
L L B data to A busL H A data to B busH X Isolation
LOGIC SYMBOL
(1)
(1) This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
2
www.ti.com
To Seven Other Channels
1DIR
1A1
1B1
1OE
To Seven Other Channels
2DIR
2A1
2B1
2OE
1
47
24
36
48
2
25
13
Absolute Maximum Ratings
(1)
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300G – MARCH 1994 – REVISED JANUARY 2006
LOGIC DIAGRAM (POSITIVE LOGIC)
over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
V
CC
Supply voltage range –0.5 7 VV
I
Input voltage range (except I/O ports)
(2)
–0.5 7 VV
O
Voltage range applied to any output in the high or power-off state –0.5 5.5 VSN54ABT16245A 96I
O
Current into any output in the low state mASN74ABT16245A 128I
IK
Input clamp current V
I
< 0 –18 mAI
OK
Output clamp current V
O
< 0 –50 mADGG package 89θ
JA
Package thermal impedance
(3)
DGV package 93 °C/WDL package 94T
stg
Storage temperature range –65 150 °C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratingsonly, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operatingconditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2) The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.(3) The package thermal impedance is calculated in accordance with JESD 51.
3
www.ti.com
Recommended Operating Conditions
(1)
SN54ABT16245A, SN74ABT16245A16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300G – MARCH 1994 – REVISED JANUARY 2006
SN54ABT16245A SN74ABT16245A
UNITMIN MAX MIN MAX
V
CC
Supply voltage 4.5 5.5 4.5 5.5 VV
IH
High-level input voltage 2 2 VV
IL
Low-level input voltage 0.8 0.8 VV
I
Input voltage 0 V
CC
0 V
CC
VI
OH
High-level output current –24 –32 mAI
OL
Low-level output current 48 64 mA∆t/ ∆v Input transition rise or fall rate Outputs enabled 10 10 ns/V∆t/ ∆V
CC
Power-up ramp rate 200 200 µs/VT
A
Operating free-air temperature –55 125 –40 85 °C
(1) All unused inputs of the device must be held at V
CC
or GND to ensure proper device operation. Refer to the TI application report,Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
4
www.ti.com
Electrical Characteristics
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300G – MARCH 1994 – REVISED JANUARY 2006
over recommended operating free-air temperature range (unless otherwise noted)
T
A
= 25 °C SN54ABT16245A SN74ABT16245APARAMETER TEST CONDITIONS UNITMIN TYP
(1)
MAX MIN MAX MIN MAX
V
IK
V
CC
= 4.5 V, I
I
= –18 mA –1.2 –1.2 –1.2 VV
CC
= 4.5 V, I
OH
= –3 mA 2.5 2.5 2.5V
CC
= 5 V, I
OH
= –3 mA 3 3 3V
OH
VI
OH
= –24 mA 2 2V
CC
= 4.5 V
I
OH
= –32 mA 2
(2)
2I
OL
= 48 mA 0.55 0.55V
OL
V
CC
= 4.5 V VI
OL
= 64 mA 0.55
(2)
0.55V
hys
100 mVControl
V
CC
= 0 to 5.5 V, V
I
= V
CC
or GND ±1±1±1inputsI
I
µAA or B
V
CC
= 2.1 V to 5.5 V, V
I
= V
CC
or GND ±20
(2)
±100 ±20portI
OZPU
V
CC
= 0 to 2.1 V, V
O
= 0.5 V to 2.7 V, OE = X ±50
(3)
±50
(3)
±50 µAI
OZPD
V
CC
= 2.1 V to 0, V
O
= 0.5 V to 2.7 V, OE = X ±50
(3)
±50
(3)
±50 µAI
OZH
(4)
V
CC
= 2.1 V to 5.5 V, V
O
= 2.7 V, OE ≥2 V 10
(5)
10 10
(5)
µAI
OZL
(4)
V
CC
= 2.1 V to 5.5 V, V
O
= 0.5 V, OE ≥2 V –10
(5)
–10 –10
(5)
µAI
off
V
CC
= 0, V
I
or V
O
≤5.5 V ±100 ±100 µAV
CC
= 5.5 V,I
CEX
Outputs high 50 50 50 µAV
O
= 5.5 VI
O
(6)
V
CC
= 5.5 V, V
O
= 2.5 V –50 –100 –180 –50 –180 –50 –180 mAOutputs high 2 2 2A or B V
CC
= 5.5 V, I
O
= 0,I
CC
Outputs low 32 32 32 mAport V
I
= V
CC
or GND
Outputs disabled 2 2 2V
CC
= 5.5 V, Outputs enabled 2 1.5 2Data One inputs at 3.4 V,inputs Other inputs at
Outputs disabled 0.05 1 0.05∆I
CC
(7)
mAV
CC
or GNDControl V
CC
= 5.5 V, One input at 3.4 V,
1.5 1.5 1.5inputs Other inputs at V
CC
or GNDControlC
i
V
I
= 2.5 V or 0.5 V 3 pFinputs
A or BC
o
V
O
= 2.5 V or 0.5 V 6 pFport
(1) All typical values are at V
CC
= 5 V.(2) On products compliant to MIL-PRF-38535, this parameter does not apply.(3) On products compliant to MIL-PRF-38535, this parameter is not production tested.(4) The parameters I
OZH
and I
OZL
include the input leakage current.(5) This limit may vary among suppliers.(6) Not more than one output should be tested at a time, and the duration of the test should not exceed one second.(7) This is the increase in supply current for each input that is at the specified TTL voltage level, rather than V
CC
or GND.
5
www.ti.com
Switching Characteristics
Switching Characteristics
SN54ABT16245A, SN74ABT16245A16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300G – MARCH 1994 – REVISED JANUARY 2006
over recommended operating ranges of supply voltage and operating free-air temperature, C
L
= 50 pF(unless otherwise noted) (see Figure 1 )
SN54ABT16245A
FROM TO V
CC
= 5 V,PARAMETER UNIT(INPUT) (OUTPUT) T
A
= 25 °C
MIN MAXMIN TYP MAX
t
PLH
0.5 2.2 3.4 0.5 4A or B B or A nst
PHL
0.5 2.3 3.8 0.5 4.6t
PZH
0.8 3.6 5.2 0.8 5.5OE B or A nst
PZL
0.9 3.7 6.1 0.1 7.3t
PHZ
1.3 4.4 5.8 1.3 6.3OE B or A nst
PLZ
1.4 3.3 4.7 1.4 5.5
over recommended operating ranges of supply voltage and operating free-air temperature, C
L
= 50 pF(unless otherwise noted) (see Figure 1 )
SN74ABT16245A
FROM TO V
CC
= 5 V,PARAMETER UNIT(INPUT) (OUTPUT) T
A
= 25 °C
MIN MAXMIN TYP MAX
t
PLH
1 2.2 3.4 1 3.9A or B B or A nst
PHL
1 2.3 3.7 1 4.2t
PZH
1 3.6 5.2 1 6.3OE B or A nst
PZL
1 3.7 5.4 1 6.4t
PHZ
2 4.4 5.8 2 6.3OE B or A nst
PLZ
1.5 3.3 4.7 1.5 5.2
6
www.ti.com
PARAMETER MEASUREMENT INFORMATION
1.5 V
th
tsu
From Output
Under Test
CL = 50 pF
(see Note A)
LOAD CIRCUIT
S1
7 V
Open
GND
500 Ω
500 Ω
Data Input
Timing Input 1.5 V 3 V
0 V
1.5 V 1.5 V 3 V
0 V
3 V
0 V
1.5 V
tw
Input
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VOLTAGE WA VEFORMS
PULSE DURATION
tPLH
tPHL
tPHL
tPLH
VOH
VOH
VOL
VOL
1.5 V 1.5 V 3 V
0 V
1.5 V1.5 V
Input
1.5 V
Output
Control
Output
Waveform 1
S1 at 7 V
(see Note B)
Output
Waveform 2
S1 at Open
(see Note B)
VOL
VOH
tPZL
tPZH
tPLZ
tPHZ
1.5 V1.5 V
3.5 V
0 V
1.5 V VOL + 0.3 V
1.5 V VOH − 0.3 V
≈0 V
3 V
VOLTAGE WA VEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
Output
Output
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
7 V
Open
TEST S1
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf≤ 2.5 ns.
D. The outputs are measured one at a time, with one transition per measurement.
1.5 V
SN54ABT16245A, SN74ABT16245A
16-BIT BUS TRANSCEIVERS
WITH 3-STATE OUTPUTS
SCBS300G – MARCH 1994 – REVISED JANUARY 2006
Figure 1. Load Circuit and Voltage Waveforms
7
PACKAGE OPTION ADDENDUM
www.ti.com 5-Sep-2011
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
5962-9317501MXA ACTIVE CFP WD 48 1 TBD Call TI Call TI
74ABT16245ADGGRG4 ACTIVE TSSOP DGG 48 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ABT16245ADGVRE4 ACTIVE TVSOP DGV 48 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ABT16245ADGVRG4 ACTIVE TVSOP DGV 48 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN74ABT16245ADGGR ACTIVE TSSOP DGG 48 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN74ABT16245ADGVR ACTIVE TVSOP DGV 48 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN74ABT16245ADL ACTIVE SSOP DL 48 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN74ABT16245ADLG4 ACTIVE SSOP DL 48 25 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN74ABT16245ADLR ACTIVE SSOP DL 48 1000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SN74ABT16245ADLRG4 ACTIVE SSOP DL 48 1000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
SNJ54ABT16245AWD ACTIVE CFP WD 48 1 TBD A42 N / A for Pkg Type
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
PACKAGE OPTION ADDENDUM
www.ti.com 5-Sep-2011
Addendum-Page 2
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF SN54ABT16245A, SN74ABT16245A :
•Catalog: SN74ABT16245A
•Enhanced Product: SN74ABT16245A-EP, SN74ABT16245A-EP
•Military: SN54ABT16245A
NOTE: Qualified Version Definitions:
•Catalog - TI's standard catalog product
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
•Military - QML certified for Military and Defense Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
SN74ABT16245ADGGR TSSOP DGG 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 Q1
SN74ABT16245ADGVR TVSOP DGV 48 2000 330.0 16.4 7.1 10.2 1.6 12.0 16.0 Q1
SN74ABT16245ADLR SSOP DL 48 1000 330.0 32.4 11.35 16.2 3.1 16.0 32.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN74ABT16245ADGGR TSSOP DGG 48 2000 367.0 367.0 45.0
SN74ABT16245ADGVR TVSOP DGV 48 2000 367.0 367.0 38.0
SN74ABT16245ADLR SSOP DL 48 1000 367.0 367.0 55.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
MECHANICAL DATA
MCFP010B – JANUARY 1995 – REVISED NOVEMBER 1997
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
WD (R-GDFP-F**) CERAMIC DUAL FLATPACK
4040176/D 10/97
48 LEADS SHOWN
48
48
25
56
0.610
(18,80)
0.710
(18,03)
0.7400.640
0.390 (9,91)
0.370 (9,40)
0.870 (22,10)
1.130 (28,70)
1
A
0.120 (3,05)
0.075 (1,91)
LEADS**
24
NO. OF
A MIN
A MAX (16,26)
(15,49)
0.025 (0,635)
0.009 (0,23)
0.004 (0,10)
0.370 (9,40)
0.250 (6,35)
0.370 (9,40)
0.250 (6,35)
0.014 (0,36)
0.008 (0,20)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification only
E. Falls within MIL STD 1835: GDFP1-F48 and JEDEC MO-146AA
GDFP1-F56 and JEDEC MO-146AB
MECHANICAL DATA
MPDS006C – FEBRUAR Y 1996 – REVISED AUGUST 2000
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE
24 PINS SHOWN
14
3,70
3,50 4,90
5,10
20
DIM
PINS **
4073251/E 08/00
1,20 MAX
Seating Plane
0,05
0,15
0,25
0,50
0,75
0,23
0,13
112
24 13
4,30
4,50
0,16 NOM
Gage Plane
A
7,90
7,70
382416
4,90
5,103,70
3,50
A MAX
A MIN
6,60
6,20
11,20
11,40
56
9,60
9,80
48
0,08
M
0,07
0,40
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
D. Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
MECHANICAL DATA
MSSO001C – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DL (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
4040048/E 12/01
48 PINS SHOWN
56
0.730
(18,54)
0.720
(18,29)
4828
0.370
(9,40)
(9,65)
0.380
Gage Plane
DIM
0.420 (10,67)
0.395 (10,03)
A MIN
A MAX
0.010 (0,25)
PINS **
0.630
(16,00)
(15,75)
0.620
0.010 (0,25)
Seating Plane
0.020 (0,51)
0.040 (1,02)
25
24
0.008 (0,203)
0.0135 (0,343)
48
1
0.008 (0,20) MIN
A
0.110 (2,79) MAX
0.299 (7,59)
0.291 (7,39)
0.004 (0,10)
M
0.005 (0,13)
0.025 (0,635)
0°–ā8°
0.005 (0,13)
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO-118
MECHANICAL DATA
MTSS003D – JANUARY 1995 – REVISED JANUAR Y 1998
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
4040078/F 12/97
48 PINS SHOWN
0,25
0,15 NOM
Gage Plane
6,00
6,20 8,30
7,90
0,75
0,50
Seating Plane
25
0,27
0,17
24
A
48
1
1,20 MAX
M
0,08
0,10
0,50
0°–8°
56
14,10
13,90
48
DIM
A MAX
A MIN
PINS **
12,40
12,60
64
17,10
16,90
0,15
0,05
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
