OPA2691 OPA 269 1 OPA 26 9 1 SBOS224D - DECEMBER 2001 - REVISED JULY 2008 www.ti.com Dual Wideband, Current-Feedback OPERATIONAL AMPLIFIER With Disable FEATURES APPLICATIONS FLEXIBLE SUPPLY RANGE: +5V to +12V Single Supply 2.5V to 6V Dual Supply WIDEBAND +5V OPERATION: 190MHz (G = +2) UNITY-GAIN STABLE: 280MHz (G = 1) HIGH OUTPUT CURRENT: 190mA OUTPUT VOLTAGE SWING: 4.0V HIGH SLEW RATE: 2100V/s LOW SUPPLY CURRENT: 5.1mA/ch LOW DISABLED CURRENT: 150A/ch DESCRIPTION The OPA2691's low 5.1mA/ch supply current is precisely trimmed at 25C. This trim, along with low drift over temperature, ensures lower maximum supply current than competing products. System power may be further reduced by using the optional disable control pin (SO-14 only). Leaving this disable pin open, or holding it HIGH, gives normal operation. If pulled LOW, the OPA2691 supply current drops to less than 150A/ch while the output goes into a high impedance state. This feature may be used for power savings. The OPA2691 sets a new level of performance for broadband dual current-feedback op amps. Operating on a very low 5.1mA/ch supply current, the OPA2691 offers a slew rate and output power normally associated with a much higher supply current. A new output stage architecture delivers a high output current with minimal voltage headroom and crossover distortion. This gives exceptional single-supply operation. Using a single +5V supply, the OPA2691 can deliver a 1V to 4V output swing with over 150mA drive current and 190MHz bandwidth. This combination of features makes the OPA2691 an ideal RGB line driver or single-supply Analog-to-Digital Converter (ADC) input driver. xDSL LINE DRIVER / RECEIVER MATCHED I/Q CHANNEL AMPLIFIER BROADBAND VIDEO BUFFERS HIGH-SPEED IMAGING CHANNELS PORTABLE INSTRUMENTS DIFFERENTIAL ADC DRIVERS ACTIVE FILTERS WIDEBAND INVERTING SUMMING OPA2691 RELATED PRODUCTS Voltage-Feedback Current-Feedback Fixed Gain SINGLES DUALS TRIPLES OPA690 OPA691 OPA692 OPA2690 OPA2681 -- OPA3690 OPA3691 OPA3692 +12V SINGLE-SUPPLY ADSL UPSTREAM DRIVER SMALL-SIGNAL FREQUENCY RESPONSE 1/2 OPA2691 324 18 12.4 1:2 17 2k 1F 100 2k 15Vp-p 100 324 12.4 16 Gain (dB) +6.0V 2Vp-p 15 14 1/2 OPA2691 13 12 Single-Supply ADSL Upstream Driver 0.1 1 10 100 200 Frequency (MHz) Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright (c) 2001-2008, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com PACKAGE/ORDERING INFORMATION(1) PRODUCT OPA2691 " OPA2691 " PACKAGE-LEAD PACKAGE DESIGNATOR SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY SO-8 D -40C to +85C OPA2691 " " " " OPA2691ID OPA2691IDR Rails, 100 Tape and Reel, 2500 SO-14 D -40C to +85C OPA2691 " " " " OPA2691I-14D OPA2691I-14DR Rails, 58 Tape and Reel, 2500 NOTE: (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI web site at www.ti.com. PIN CONFIGURATIONS ABSOLUTE MAXIMUM RATINGS(1) Power Supply ............................................................................... 6.5VDC Internal Power Dissipation(2) ............................ See Thermal Information Differential Input Voltage .................................................................. 1.2V Input Voltage Range ........................................................................... VS Storage Temperature Range: D, 14D ............................ -65C to +125C Lead Temperature (soldering, 10s) .............................................. +300C Junction Temperature (TJ ) ........................................................... +175C ESD Performance: HBM .............................................................................................. 2000V CDM .............................................................................................. 1500V Top View NOTES:: (1) Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. Exposure to absolute maximum conditions for extended periods may affect device reliability. (2) Packages must be derated based on specified JA. Maximum TJ must be observed. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. 2 SO-8 Out A 1 8 +VS -In A 2 7 Out B +In A 3 6 -In B -VS 4 5 +In B -In A 1 14 Out A +In A 2 13 NC DIS A 3 12 NC -VS 4 11 +VS DIS B 5 10 NC +In B 6 9 NC -In B 7 8 Out B SO-14 NC = No Connection OPA2691 www.ti.com SBOS224D ELECTRICAL CHARACTERISTICS: VS = 5V Boldface limits are tested at +25C. RF = 402, RL = 100, and G = +2, (see Figure 1 for AC performance only), unless otherwise noted. OPA2691ID, I-14D TYP AC PERFORMANCE (see Figure 1) Small-Signal Bandwidth (VO = 0.5Vp-p) Bandwidth for 0.1dB Gain Flatness Peaking at a Gain of +1 Large-Signal Bandwidth Slew Rate Rise-and-Fall Time Settling Time to 0.02% 0.1% Harmonic Distortion 2nd-Harmonic 3rd-Harmonic Input Voltage Noise Noninverting Input Current Noise Inverting Input Current Noise Differential Gain Differential Phase 0C to 70C(2) -40C to +85C(2) 200 190 180 40 1 35 1.5 20 2 1400 1375 1350 -70 -79 -74 -93 1.7 12 15 0.07 0.17 0.02 0.07 -86 -63 -70 -72 -87 2.5 14 17 -60 -67 -70 -82 2.9 15 18 225 0.8 125 3 +15 +35 5 25 3.5 56 100 || 2 37 3.4 4.0 3.9 +190 -190 250 0.03 3.8 3.7 +25C G = +1, RF = 453 G = +2, RF = 402 G = +5, RF = 261 G = +10, RF = 180 G = +2, VO = 0.5Vp-p RF = 453, VO = 0.5Vp-p G = +2, VO = 5Vp-p G = +2, 4V Step G = +2, VO = 0.5V Step G = +2, 5V Step G = +2, VO = 2V Step G = +2, VO = 2V Step G = +2, f = 5MHz, VO = 2Vp-p RL = 100 RL 500 RL = 100 RL 500 f > 1MHz f > 1MHz f > 1MHz G = +2, NTSC, VO = 1.4Vp, RL = 150 RL = 37.5 G = +2, NTSC, VO = 1.4Vp, RL = 150 RL = 37.5 f = 5MHz 280 225 210 200 90 0.2 200 2100 1.6 1.9 12 8 VO = 0V, RL = 100 VCM = 0V VCM = 0V VCM = 0V VCM = 0V VCM = 0V VCM = 0V Channel-to-Channel Crosstalk DC PERFORMANCE(4) Open-Loop Transimpedance Gain (ZOL) Input Offset Voltage Average Offset Voltage Drift Noninverting Input Bias Current Average Noninverting Input Bias Current Drift Inverting Input Bias Current Average Inverting Input Bias Current Drift INPUT Common-Mode Input Range (CMIR)(5) Common-Mode Rejection (CMRR) Noninverting Input Impedance Inverting Input Resistance (RI) OUTPUT Voltage Output Swing Current Output, Sourcing Current Output, Sinking Short-Circuit Current Closed-Loop Output Impedance DISABLE (Disabled LOW) (SO-14 only) Power-Down Supply Current (+VS) Disable Time Enable Time Off Isolation Output Capacitance in Disable Turn-On Glitch Turn-Off Glitch Enable Voltage Disable Voltage Control Pin Input Bias Current (DIS ) POWER SUPPLY Specified Operating Voltage Maximum Operating Voltage Range Minimum Operating Voltage Range Max Quiescent Current Min Quiescent Current Power-Supply Rejection Ratio (-PSRR) TEMPERATURE RANGE Specification: D, 14D Thermal Resistance, JA D SO-8 14D SO-14 +25C(1) CONDITIONS PARAMETER VCM = 0V Open-Loop No Load 100 Load VO = 0 VO = 0 G = +2, f = 100kHz VDIS = 0, Both Channels VIN = 1VDC VIN = 1VDC G = +2, 5MHz G = +2, RL = 150, VIN = 0 G = +2, RL = 150, VIN = 0 VDIS = 0, Each Channel UNITS MIN/ TEST MAX LEVEL(3) MHz MHz MHz MHz MHz dB MHz V/s ns ns ns ns typ min typ typ min max typ min typ typ typ typ C B C C B B C B C C C C -58 -65 -68 -78 3.1 15 19 dBc dBc dBc dBc nV/Hz pA/Hz pA/Hz % % deg deg dBc max max max max max max max typ typ typ typ typ B B B B B B B C C C C C 110 3.7 12 +43 -300 30 90 100 4.3 20 +45 -300 40 200 k mV V/C A nA/C A nA/C min max max max max max max A A B A B A B 3.3 51 3.2 50 V dB k || pF min min typ typ A A C C +160 -160 3.7 3.6 +140 -140 3.6 3.3 +100 -100 V V mA mA mA min min min min typ typ A A A A C C -600 -700 -800 3.5 1.7 130 3.6 1.6 150 3.7 1.5 160 A ns ns dB pF mV mV V V A max typ typ typ typ typ typ min max max A C C C C C C A A A 6 6 6 10.6 9.8 52 11.2 9.2 50 11.5 8.9 49 V V V mA mA dB typ max min max min min C A C A A A -40 to +85 C typ C 125 100 C/W C/W typ typ C C -300 400 25 70 4 50 20 3.3 1.8 75 5 VS = 5V, Both Channels VS = 5V, Both Channels Input Referred MIN/MAX OVER TEMPERATURE 2 10.2 10.2 58 Junction-to-Ambient 52 NOTES: (1) Junction temperature = ambient for +25 C specifications. (2) Junction temperature = ambient at low temperature limit: junction temperature = ambient +15C at high temperature limit for over temperature specifications. (3) Test Levels: (A) 100% tested at +25C. Over-temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out of node. VCM is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMRR at CMIR limits. OPA2691 SBOS224D www.ti.com 3 ELECTRICAL CHARACTERISTICS: VS = +5V Boldface limits are tested at +25C. RF = 453, RL = 100 to VS/2, and G = +2, (see Figure 1 for AC performance only), unless otherwise noted. OPA2691ID, I-14D TYP +25C(1) 0C to 70C(2) -40C to +85C(2) 168 160 140 40 1 30 2.5 25 3.0 600 575 550 -66 -73 -71 -77 1.7 12 15 -58 -65 -68 -72 2.5 14 17 -57 -63 -67 -70 2.9 15 18 200 0.8 3.5 100 +20 +40 5 20 Open-Loop 1.5 3.5 54 100 || 2 40 No Load RL = 100, 2.5V No Load RL = 100, 2.5V VO = VS /2 VO = VS /2 G = +2, f = 100kHz VDIS = 0, Both Channels G = +2, 5MHz CONDITIONS +25C 210 190 180 155 90 0.2 210 850 2.0 2.3 14 10 Input Voltage Noise Noninverting Input Current Noise Inverting Input Current Noise G = +1, RF = 499 G = +2, RF = 453 G = +5, RF = 340 G = +10, RF = 180 G = +2, VO < 0.5Vp-p RF = 649, VO < 0.5Vp-p G = +2, VO = 2Vp-p G = +2, 2V Step G = +2, VO = 0.5V Step G = +2, VO = 2V Step G = +2, VO = 2V Step G = +2, VO = 2V Step G = +2, f = 5MHz, VO = 2Vp-p RL = 100 to VS /2 RL 500 to VS /2 RL = 100 to VS /2 RL 500 to VS /2 f > 1MHz f > 1MHz f > 1MHz DC PERFORMANCE(4) Open-Loop Transimpedance Gain (ZOL) Input Offset Voltage Average Offset Voltage Drift Noninverting Input Bias Current Average Noninverting Input Bias Current Drift Inverting Input Bias Current Average Inverting Input Bias Current Drift VO = VS/2, RL = 100 to VS/2 VCM = 2.5V VCM = 2.5V VCM = 2.5V VCM = 2.5V VCM = 2.5V VCM = 2.5V PARAMETER AC PERFORMANCE (see Figure 2) Small-Signal Bandwidth (VO = 0.5Vp-p) Bandwidth for 0.1dB Gain Flatness Peaking at a Gain of +1 Large-Signal Bandwidth Slew Rate Rise-and-Fall Time Settling Time to 0.02% 0.1% Harmonic Distortion 2nd-Harmonic 3rd-Harmonic INPUT Least Positive Input Voltage(5) Most Positive Input Voltage(5) Common-Mode Rejection (CMRR) Noninverting Input Impedance Inverting Input Resistance (RI) OUTPUT Most Positive Output Voltage Least Positive Output Voltage Current Output, Sourcing Current Output, Sinking Closed-Loop Output Impedance DISABLE (Disabled LOW) (SO-14 only) Power-Down Supply Current (+VS) Off Isolation Output Capacitance in Disable Turn-On Glitch Turn-Off Glitch Enable Voltage Disable Voltage Control Pin Input Bias Current (DIS ) POWER SUPPLY Specified Single-Supply Operating Voltage Maximum Single-Supply Operating Voltage Minimum Single-Supply Operating Voltage Max Quiescent Current Min Quiescent Current Power-Supply Rejection Ratio (+PSRR) MIN / MAX OVER TEMPERATURE VCM = 2.5V G = +2, RL = 150, VIN = VS /2 G = +2, RL = 150, VIN = VS /2 VDIS = 0, Each Channel TEMPERATURE RANGE Specification: D, 14D Thermal Resistance, JA D SO-8 14D SO-14 MIN/ TEST MAX LEVEL(3) MHz MHz MHz MHz MHz dB MHz V/s ns ns ns ns typ min typ typ min max typ min typ typ typ typ C B C C B B C B C C C C -56 -62 -65 -69 3.1 15 19 dBc dBc dBc dBc nV/ Hz pA/ Hz pA/ Hz max max max max max max max B B B B B B B 90 4.1 12 +48 -250 25 112 80 4.8 20 +56 -250 35 250 k mV V/C A nA/C A nA /C min max max max max max max A A B A B A B 1.6 3.4 50 1.7 3.3 49 1.8 3.2 48 V V dB k || pF max min min typ typ A A A C C 4 3.9 1 1.1 +160 -160 0.03 3.8 3.7 1.2 1.3 +120 -120 3.7 3.6 1.3 1.4 +100 -100 3.5 3.4 1.5 1.6 +80 -80 V V V V mA mA min min max max min min typ A A A A A A C -300 65 4 50 20 3.3 1.8 75 -600 -700 -800 3.5 1.7 130 3.6 1.6 150 3.7 1.5 160 A dB pF mV mV V V A max typ typ typ typ min max typ A C C C C A A C 12 12 12 9.6 8.2 10 8.0 10.4 7.8 V V V mA mA dB typ max min max min typ C A C A A C -40 to +85 C typ C 125 100 C/W C/W typ typ C C 5 VS = +5V, Both Channels VS = +5V, Both Channels Input Referred UNITS 4 9 9 55 NOTES: (1) Junction temperature = ambient for +25C specifications. (2) Junction temperature = ambient at low temperature limit: junction temperature = ambient +15C at high temperature limit for over temperature specifications. (3) Test Levels: (A) 100% tested at +25C. Over-temperature limits by characterization and simulation. (B) Limits set by characterization and simulation. (C) Typical value only for information. (4) Current is considered positive out of node. VCM is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMRR at CMIR limits. 4 OPA2691 www.ti.com SBOS224D TYPICAL CHARACTERISTICS: VS = 5V G = +2, RF = 402, RL = 100, unless otherwise noted (see Figure 1 for AC performance only). SMALL-SIGNAL FREQUENCY RESPONSE 1 G = +1, RF = 453 0 -1 -3 G = +5, RF = 261 -5 G = +10, RF = 180 -6 2Vp-p 5.5 5.0 4.5 4.0 3.5 4Vp-p 3.0 -7 7Vp-p 2.5 VO = 0.5Vp-p -8 2.0 0 125MHz 250MHz 0 Frequency (25MHz/div) 250MHz LARGE-SIGNAL PULSE RESPONSE SMALL-SIGNAL PULSE RESPONSE +4 G = +2 VO = 0.5Vp-p +300 G = +2 VO = 5Vp-p +3 Output Voltage (1V/div) Output Voltage (100mV/div) 125MHz Frequency (25MHz/div) +400 +200 +100 0 -100 -200 +2 +1 0 -1 -2 -3 -300 -4 -400 Time (5ns/div) Time (5ns/div) CHANNEL-TO-CHANNEL CROSSTALK COMPOSITE VIDEO dG/dP 0.2 -55 +5 Video In 0.18 No Pull-Down With 1.3k Pull-Down Video Loads 1/2 OPA2691 0.16 -60 -65 402 402 dG Crosstalk (5dB/div) 0.14 dG/dP (%/) 1Vp-p 6.0 -2 -4 G = +2, RL = 100 6.5 G = +2, RF = 402 Gain (0.5dB/div) Normalized Gain (1dB/div) LARGE-SIGNAL FREQUENCY RESPONSE 7.0 Optional 1.3k -5 Pull-Down 0.12 dG 0.1 0.08 0.06 dP -75 -80 -85 -90 0.04 dP 0.02 -70 -95 -100 0 1 2 3 1 4 OPA2691 SBOS224D 10 100 Frequency (MHz) Number of 150 Loads www.ti.com 5 TYPICAL CHARACTERISTICS: VS = 5V (Cont.) G = +2, RF = 402, RL = 100, unless otherwise noted (see Figure 1 for AC performance only). HARMONIC DISTORTION vs LOAD RESISTANCE HARMONIC DISTORTION vs SUPPLY VOLTAGE -60 -60 Harmonic Distortion (dBc) Harmonic Distortion (dBc) VO = 2Vp-p RL = 100 f = 5MHz VO = 2Vp-p f = 5MHz -65 -70 2nd-Harmonic -75 -80 -85 3rd-Harmonic -90 -65 2nd-Harmonic -70 -75 3rd-Harmonic -80 -95 -100 -85 100 1000 2.5 3 Load Resistance () HARMONIC DISTORTION vs FREQUENCY 5 5.5 6 HARMONIC DISTORTION vs OUTPUT VOLTAGE -60 RL = 100 f = 5MHz VO = 2Vp-p RL = 100 Harmonic Distortion (dBc) Harmonic Distortion (dBc) 4.5 -65 dBc = dB Below Carrier 2nd-Harmonic -70 3rd-Harmonic -80 -90 -100 2nd-Harmonic -70 -75 3rd-Harmonic -80 -85 0.1 1 10 20 0.1 1 Frequency (MHz) 5 Output Voltage Swing (Vp-p) HARMONIC DISTORTION vs INVERTING GAIN HARMONIC DISTORTION vs NONINVERTING GAIN -50 -50 VO = 2Vp-p RL = 100 f = 5MHz Harmonic Distortion (dBc) Harmonic Distortion (dBc) 4 Supply Voltage (V) -50 -60 2nd-Harmonic -70 3rd-Harmonic -80 VO = 2Vp-p RL = 100 f = 5MHz RF = 402 -60 2nd-Harmonic -70 3rd-Harmonic -80 -90 -90 1 1 10 10 Inverting Gain (V/V) Gain (V/V) 6 3.5 OPA2691 www.ti.com SBOS224D TYPICAL CHARACTERISTICS: VS = 5V (Cont.) G = +2, RF = 402, RL = 100, unless otherwise noted (see Figure 1 for AC performance only). 2-TONE, 3RD-ORDER INTERMODULATION SPURIOUS INPUT VOLTAGE AND CURRENT NOISE DENSITY -30 3rd-Order Spurious Level (dBc) Current Noise (pA/Hz) Voltage Noise (nV/Hz) 100 Inverting Input Current Noise (15pA/Hz) 10 Noninverting Input Current Noise (12pA/Hz) Voltage Noise (1.7nV/Hz) dBc = dB below carriers 20MHz -50 10MHz -60 -70 -80 Load Power at Matched 50 Load -90 1 100 1k 10k 100k 1M -8 10M -6 -4 RECOMMENDED RS vs CAPACITIVE LOAD Normalized Gain to Capacitive Load (dB) 60 RS () 50 40 30 20 10 0 100 8 10 CL = 10pF CL = 22pF 0 1/2 OPA2691 RS VO CL 1k 402 -6 402 -9 125MHz Output Voltage 1.2 0.8 250MHz DISABLED FEEDTHROUGH vs FREQUENCY 4.0 2.0 0 2.0 CL = 100pF 1k is optional. Frequency (25MHz/div) -45 VDIS = 0 -50 -55 Feedthrough (5dB/div) VDIS CL = 47pF VIN -3 0 VDIS (2V/div) Output Voltage (400mV/div) 6 3 1k 6.0 0 4 6 LARGE-SIGNAL DISABLE/ENABLE RESPONSE 0.4 2 9 Capacitive Load (pF) 1.6 0 FREQUENCY RESPONSE vs CAPACITIVE LOAD 70 10 -2 Single-Tone Load Power (dBm) Frequency (Hz) 1 50MHz -40 -60 -65 -70 -75 -80 Reverse -85 -90 VIN = +1V Forward -95 -100 0.3 Time (200ns/div) 1 10 100 Frequency (MHz) OPA2691 SBOS224D www.ti.com 7 TYPICAL CHARACTERISTICS: VS = 5V (Cont.) G = +2, RF = 402, RL = 100, unless otherwise noted (see Figure 1 for AC performance only). TYPICAL DC DRIFT OVER TEMPERATURE OUTPUT VOLTAGE AND CURRENT LIMITATIONS 2 Output Current Limit 1W Internal Power Limit Single Channel 1.5 Input Offset Voltage (mV) 3 2 VO (V) 1 0 25 Load Line 50 Load Line -1 -2 100 Load Line -3 -4 1W Internal Power Limit Single Channel Output Current Limit -5 -300 -250 -200 -150 -100 -50 0 30 Noninverting Input Bias Current (IB+) 1 0.5 10 0 0 Inverting Input Bias Current (IB-) -0.5 -10 -1 -20 Input Offset Voltage (VOS) -1.5 -2 -25 0 25 50 75 100 125 Ambient Temperature (C) SUPPLY AND OUTPUT CURRENT vs TEMPERATURE CMRR AND PSRR vs FREQUENCY 16 65 250 +PSRR Sourcing Output Current Supply Current (2mA/div) 60 55 CMRR 50 45 -30 -40 -50 +50 +100 +150 +200 +250 +300 IO (mA) Common-Mode Rejection Ratio (dB) Power-Supply Rejection Ratio (dB) 20 -PSRR 40 35 30 14 200 Sinking Output Current 12 150 10 100 Quiescent Supply Current Both Channels 8 50 Output Current (50mA/div) 4 40 Input Bias Currents (A) 5 25 6 20 1k 10k 100k 1M 10M 0 -50 100M -25 0 25 50 75 100 125 Ambient Temperature (C) Frequency (Hz) CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY OPEN-LOOP TRANSIMPEDANCE GAIN/PHASE 10 120 0 1/2 OPA2691 1 -5V ZO 402 402 0.1 0.01 -40 | ZOL| 80 -80 ZOL 60 -120 40 -160 20 -200 0 10k 100k 1M 10M 100M Frequency (Hz) 8 100 -240 10k 100k 1M 10M 100M 1G Frequency (Hz) OPA2691 www.ti.com SBOS224D Transimpedance Phase (40/div) 50 Transimpedance Gain (20dB/div) Output Impedance () +5V TYPICAL CHARACTERISTICS: VS = +5V G = +2, RF = 499, RL = 100 to +2.5V, unless otherwise noted (see Figure 2 for AC performance only). LARGE-SIGNAL FREQUENCY RESPONSE SMALL-SIGNAL FREQUENCY RESPONSE 1 7.0 G = +1, RF = 499 6.0 -1 G = +2, RF = 453 -2 G = +5, RF = 340 -3 -4 -5 -6 -7 -8 5.5 5.0 VO = 2Vp-p 4.5 4.0 3.5 3.0 G = +10, RF = 180 VO = 0.5Vp-p VO = 0.5Vp-p 6.5 Gain (0.5dB/div) Normalized Gain (1dB/div) 0 2.0 0 125MHz 0 250MHz 125MHz SMALL-SIGNAL PULSE RESPONSE LARGE-SIGNAL PULSE RESPONSE 4.1 2.9 2.7 2.6 2.5 2.4 2.3 G = +2 VO = 2Vp-p 3.7 Output Voltage (400mV/div) G = +2 VO = 0.5Vp-p 2.8 2.2 3.3 2.9 2.5 2.1 1.7 1.3 2.1 0.9 Time (5ns/div) Time (5ns/div) FREQUENCY RESPONSE vs CAPACITIVE LOAD RECOMMENDED RS vs CAPACITIVE LOAD Normalized Gain to Capacitive Load (dB) 60 50 40 RS () 250MHz Frequency (25MHz/div) Frequency (25MHz/div) Output Voltage (100mV/div) VO = 1Vp-p G = +2 RL = 100 to 2.5V 2.5 30 20 10 0 1 10 100 6 CL = 10pF 3 CL = 47pF 0 CL = 22pF +5V -3 VI 0.1F 57.6 806 806 VO 1/2 OPA2691 CL = 100pF RS -6 453 CL 1k 453 0.1F 1k is optional. -9 0 1k 125MHz 250MHz Frequency (25MHz/div) Capacitive Load (pF) OPA2691 SBOS224D 9 www.ti.com 9 TYPICAL CHARACTERISTICS: VS = +5V (Cont.) G = +2, RF = 499, RL = 100 to +2.5V, unless otherwise noted (see Figure 2 for AC performance only). HARMONIC DISTORTION vs FREQUENCY HARMONIC DISTORTION vs LOAD RESISTANCE -50 -60 Harmonic Distortion (dBc) Harmonic Distortion (dBc) VO = 2Vp-p f = 5MHz -65 2nd-Harmonic -70 3rd-Harmonic -75 100 2nd-Harmonic -70 3rd-Harmonic -80 0.1 1000 1 Frequency (MHz) HARMONIC DISTORTION vs OUTPUT VOLTAGE 2-TONE, 3RD-ORDER INTERMODULATION SPURIOUS -30 3rd-Order Spurious Level (dBc) RL = 100 to 2.5V f = 5MHz 2nd-Harmonic -65 -70 3rd-Harmonic -75 -80 1 dBc = dB below carriers 50MHz -50 -60 20MHz -70 10MHz -80 -90 Load Power at Matched 50 Load -14 3 20 -40 -100 0.1 10 Resistance () -60 Harmonic Distortion (dBc) -60 -90 -80 -12 -10 -8 -6 -4 -2 0 2 Single-Tone Load Power (dBm) Output Voltage Swing (Vp-p) 10 VO = 2Vp-p RL = 100 to 2.5V OPA2691 www.ti.com SBOS224D APPLICATIONS INFORMATION WIDEBAND CURRENT-FEEDBACK OPERATION The OPA2691 gives the exceptional AC performance of a wideband current-feedback op amp with a highly linear, highpower output stage. Requiring only 5.1mA/ch quiescent current, the OPA2691 will swing to within 1V of either supply rail and deliver in excess of 160mA tested at room temperature. This low output headroom requirement, along with supply voltage independent biasing, gives remarkable single (+5V) supply operation. The OPA2691 will deliver greater than 200MHz bandwidth driving a 2Vp-p output into 100 on a single +5V supply. Previous boosted output stage amplifiers have typically suffered from very poor crossover distortion as the output current goes through zero. The OPA2691 achieves a comparable power gain with much better linearity. The primary advantage of a current-feedback op amp over a voltagefeedback op amp is that AC performance (bandwidth and distortion) is relatively independent of signal gain. For similar AC performance with improved DC accuracy, consider the high slew rate, unity-gain stable, voltage-feedback OPA2690. Figure 1 shows the DC-coupled, gain of +2, dual powersupply circuit configuration used as the basis of the 5V Electrical Characteristics and Typical Characteristics. For test purposes, the input impedance is set to 50 with a resistor to ground and the output impedance is set to 50 with a series output resistor. Voltage swings reported in the electrical characteristics are taken directly at the input and output pins while load powers (dBm) are defined at a matched 50 load. For the circuit of Figure 1, the total effective load will be 100 || 804 = 89. The disable control line (DIS) is typically left open (SO-14 only) to ensure normal amplifier operation. One optional component is included in Figure 1. In addition to the usual power-supply decoupling capacitors to ground, a 0.01F capacitor is included between the two 0.1F +5V +VS power-supply pins. In practical printed circuit board (PCB) layouts, this optional added capacitor will typically improve the 2nd-harmonic distortion performance by 3dB to 6dB. Figure 2 shows the AC-coupled, gain of +2, single-supply circuit configuration used as the basis of the +5V Electrical Characteristics and Typical Characteristics. Though not a rail-to-rail design, the OPA2691 requires minimal input and output voltage headroom compared to other very wideband current-feedback op amps. It will deliver a 3Vp-p output swing on a single +5V supply with greater than 150MHz bandwidth. The key requirement of broadband single-supply operation is to maintain input and output signal swings within the usable voltage ranges at both the input and the output. The circuit of Figure 2 establishes an input midpoint bias using a simple resistive divider from the +5V supply (two 806 resistors). The input signal is then AC-coupled into this midpoint voltage bias. The input voltage can swing to within 1.5V of either supply pin, giving a 2Vp-p input signal range centered between the supply pins. The input impedance matching resistor (57.6) used for testing is adjusted to give a 50 input match when the parallel combination of the biasing divider network is included. The gain resistor (RG) is AC-coupled, giving the circuit a DC gain of +1--which puts the input DC bias voltage (2.5V) on the output as well. The feedback resistor value has been adjusted from the bipolar supply condition to re-optimize for a flat frequency response in +5V operation, gain of +2, operation (see the Setting Resistor Values to Optimize Bandwidth section). Again, on a single +5V supply, the output voltage can swing to within 1V of either supply pin while delivering more than 75mA output current. A demanding 100 load to a midpoint bias is used in this characterization circuit. The new output stage used in the OPA2691 can deliver large bipolar output currents into this midpoint load with minimal crossover distortion, as shown by the +5V supply, 3rd-harmonic distortion plots. +5V +VS 6.8F + + 0.1F 50 Source DIS VI 50 VO 1/2 OPA2691 0.01F 6.8F 806 50 50 Load 0.1F VI 57.6 DIS 806 1/2 OPA2691 VO 100 VS/2 RF 453 RF 402 RG 402 RG 453 + 6.8F 0.1F 0.1F -VS -5V FIGURE 1. DC-Coupled, G = +2, Bipolar Supply, Specification and Test Circuit. FIGURE 2. AC-Coupled, G = +2, Single-Supply Specification and Test Circuit. OPA2691 SBOS224D www.ti.com 11 SINGLE-SUPPLY DIFFERENTIAL ADC DRIVER WIDEBAND VIDEO MULTIPLEXING Figure 3 shows a gain of +10 Single-Ended In/Diff. Out singlesupply ADC driver. Using a dual amplifier like the OPA2691 helps reduce the necessary board space, as it also reduces the amount of required supply bypassing components. From a signal point of view, dual amplifiers provide excellent performance matching (for example, gain and phase matching). The differential ADC driver circuit shown in Figure 3 takes advantage of this fact. A transformer converts the single-ended input signal into a low-level differential signal which is applied to the high impedance noninverting inputs of each of the two amplifiers in the OPA2691. Resistor RG between the inverting inputs controls the AC-gain of this circuit according to equation G = 1 + 2R F/RG. With the resistor values shown, the AC-gain is set to 10. Adding a capacitor (0.1F) in series with RG blocks, the DC-path gives a DC gain of +1 for the common-mode voltage. This allows, in a very simple way, to apply the required DC bias voltage of +2.5V to the inputs of the amplifiers, which will also appear at their outputs. Like the OPA2691, the ADC ADS823 operates on a single +5V supply. Its internal common-mode voltage is typically +2.5V which equals the required bias voltage for the OPA2691. One common application for video speed amplifiers which include a disable pin is to wire multiple amplifier outputs together, then select which one of several possible video inputs to source onto a single line. This simple Wired-OR Video Multiplexer can be easily implemented using the OPA2691I-14D, see Figure 4. Connecting two resistors between the top reference (REFT = +3.5V) and bottom reference (REFB = +1.5V) develops a +2.5V voltage level at their midpoint. Applying that to the center tap of the transformer biases the amplifiers appropriately. Sufficient bypassing at the center tap must be provided to keep this point at a solid AC ground. Resistors RS isolate the op amp output from the capacitive input of the converter, as well as forming a 1st-order, lowpass filter with capacitor C1 to attenuate some of the wideband noise. This interface will provide > 150MHz fullscale input bandwidth to the ADS823. Typically, channel switching is performed either on sync or retrace time in the video signal. The two inputs are approximately equal at this time. The make-before-break disable characteristic of the OPA2691 ensures that there is always one amplifier controlling the line when using a wired-OR circuit like that presented in Figure 4. Since both inputs may be on for a short period during the transition between channels, the outputs are combined through the output impedance matching resistors (82.5 in this case). When one channel is disabled, its feedback network forms part of the output impedance and slightly attenuates the signal in getting out onto the cable. The gain and output matching resistors have been slightly increased to get a signal gain of +1 at the matched load and provide a 75 output impedance to the cable. The video multiplexer connection (see Figure 4) also insures that the maximum differential voltage across the inputs of the unselected channel do not exceed the rated 1.2V maximum for standard video signal levels. The section on Disable Operation shows the turn-on and turn-off switching glitches using a grounded input for a single channel is typically less than 50mV. Where two outputs are switched (see Figure 4), the output line is always under the control of one amplifier or the other due to the "make-beforebreak" disable timing. In this case, the switching glitches for two 0V inputs drop to < 20mV. +5V +5V 1/2 OPA2691 1:1 +VS RS 24.9 IN C1 10pF VIN RF 200 50 0.1F + 4.7F ADS823 10-Bit 60MSPS RG 44 0.1F RF 200 RS 24.9 C1 10pF 1/2 OPA2691 IN REFT (+3.5V) REFB (+1.5V) GND 2k 2 RF G=1+ = 10 RG VBIAS = +2.5V 2k 0.1F 0.1F FIGURE 3. Wideband, Single-Supply, Differential ADC Driver. 12 OPA2691 www.ti.com SBOS224D +5V 2k VDIS +5V Power-supply decoupling not shown. Video 1 1/2 OPA2691 DIS 75 82.5 -5V 340 402 75 Cable 340 RG-59 402 +5V 82.5 1/2 OPA2691 Video 2 DIS 75 -5V 2k FIGURE 4. Two-Channel Video Multiplexer. +5V 20MHz, 2ND-ORDER BUTTERWORTH LOW-PASS FREQUENCY RESPONSE Power-supply decoupling not shown. 0.1F 12 5k 100pF 8 VI 5k 1/2 OPA2691 32.3 105 150pF 4 1/2 OPA2691 4VI Gain (dB) 51 0 -4 375 600 -8 125 -12 20MHz, 2nd-Order Butterworth Low-Pass 0.1 0.1F 1 10 100 Frequency (MHz) FIGURE 5. Buffered Single-Supply Active Filter. HIGH-SPEED ACTIVE FILTERS Wideband current-feedback op amps make ideal elements for implementing high-speed active filters where the amplifier is used as a fixed gain block inside a passive RC circuit network. Their relatively constant bandwidth versus gain, provides low interaction between the actual filter poles and the required gain for the amplifier. Figure 5 shows an example single-supply buffered filter application. In this case, one of the OPA2691 channels is used to setup the DC operating point and provide impedance isolation from the signal source into the 2nd-stage filter. That stage is set up to implement a 20MHz maximally flat Butterworth frequency response and provide an AC gain of +4. OPA2691 SBOS224D www.ti.com 13 The 51 input matching resistor is optional in this case. The input signal is AC-coupled to the 2.5V DC reference voltage developed through the resistor divider from the +5V power supply. This first stage acts as a gain of +1 voltage buffer for the signal where the 600 feedback resistor is required for stability. This first stage easily drives the low input resistors required at the input of this high-frequency filter. The 2nd stage is set for a DC gain of +1--carrying the 2.5V operating point through to the output pin, and an AC gain of +4. The feedback resistor has been adjusted to optimize bandwidth for the amplifier itself. As the single-supply frequency response plots show, the OPA2691 in this configuration will give > 200MHz small-signal bandwidth. The capacitor values were chosen as low as possible but adequate to swamp out the parasitic input capacitance of the amplifier. The resistor values were slightly adjusted to give the desired filter frequency response while accounting for the approximate 1ns propagation delay through each channel of the OPA2691. ential to single-ended conversion is performed by the voltage-feedback amplifier OPA690, configured as a standard difference amplifier. To maintain good distortion performance for the OPA2691, the loading at each amplifier output has been matched by setting R3 + R4 = R1, rather than using the same resistor values within the difference amplifier. +5V VIN +5V Line driver applications usually have a high demand for transmitting the signal with low distortion. Current-feedback amplifiers like the OPA2691 are ideal for delivering low distortion performance to higher gains. The example shown is set for a differential gain of 7.5. This circuit can deliver the maximum 15Vp-p signal with over 60MHz bandwidth. WIDEBAND (200MHz) INSTRUMENTATION AMPLIFIER As discussed previously, the current-feedback topology of the OPA2691 provides a nearly constant bandwidth as signal gain is increased. The three op amp wideband instrumentation amplifiers depicted in Figure 6 takes advantage of this, achieving a differential bandwidth of 200MHz. The signal is applied to the high-impedance noninverting inputs of the OPA2691. The differential gain is set by (1 + 2RF/RG)--which is equal to 5 using the values shown in Figure 6. The feedback resistors, RF, are optimized at this particular gain. Gain adjustments can be made by adjusting RG. The differ- VO OPA690 RG 130 RF 261 -5V R3 249 1/2 OPA2691 VO (VIN - VIN) VIN =5 R4 249 -5V INSTRUMENTATION DIFF. AMP FREQUENCY RESPONSE 15 10 Gain (dB) A very demanding application for a high-speed amplifier is to drive a low load impedance while maintaining a high output voltage swing to high frequencies. Using the dual currentfeedback op amp OPA2691, a 15Vp-p output signal swing into a twisted-pair line with a typical impedance of 100 can be realized. Configured as shown on the front page, the two amplifiers of the OPA2691 drive the output transformer in a push-pull configuration thus doubling the peak-to-peak signal swing at each op amp's output to 15Vp-p. The transformer has a turns ratio of 2. In order to provide a matched source, this requires a 25 source impedance (RS), for the primary side, given the transformer equation n2 = RL/RS. Dividing this impedance equally between the outputs requires a series termination matching resistor at each output of 12.4. Taking the total resistive load of 25 (for the differential output signal) and drawing a load line on the Output Voltage and Current Limitations plot it can be seen that a 1.5V headroom is required at both the positive and negative peak currents of 150mA. R2 499 RF 261 HIGH-POWER TWISTED-PAIR DRIVER 14 R1 499 1/2 OPA2691 5 0 1 10 100 400 Frequency (MHz) FIGURE 6. Wideband, 3-Op Amp Instrumentation Diff. Amp. DESIGN-IN TOOLS DEMONSTRATION FIXTURES Two printed circuit boards (PCBs) are available to assist in the initial evaluation of circuit performance using the OPA2691 in its two package options. Both of these are offered free of charge as unpopulated PCBs, delivered with a user's guide. The summary information for these fixtures is shown Table I below. PRODUCT OPA2691ID OPA2691I-14D PACKAGE ORDERING NUMBER LITERATURE NUMBER SO-8 SO-14 DEM-OPA-SO-2A DEM-OPA-SO-2B SBOU003 SBOU002 TABLE I. Demonstration Fixtures by Package. The demonstration fixtures can be requested at the Texas Instruments web site (www.ti.com) through the OPA2691 product folder. OPA2691 www.ti.com SBOS224D MACROMODELS AND APPLICATIONS SUPPORT Computer simulation of circuit performance using SPICE is often useful when analyzing the performance of analog circuits and systems. This is particularly true for Video and RF amplifier circuits where parasitic capacitance and inductance can have a major effect on circuit performance. A SPICE model for the OPA2691 is available through the TI web site (www.ti.com). These models do a good job of predicting small-signal AC and transient performance under a wide variety of operating conditions. They do not do as well in predicting the harmonic distortion or dG/dP characteristics. These models do not attempt to distinguish between the package types in their small-signal AC performance, nor do they attempt to simulate channel-to-channel coupling. RI, the buffer output impedance, is a critical portion of the bandwidth control equation. The OPA2691 is typically about 37. A current-feedback op amp senses an error current in the inverting node (as opposed to a differential input error voltage for a voltage-feedback op amp) and passes this on to the output through an internal frequency-dependent transimpedance gain. The Typical Characteristics show this open-loop transimpedance response. This is analogous to the openloop voltage gain curve for a voltage-feedback op amp. Developing the transfer function for the circuit of Figure 7 gives Equation 1: R 1 + F RG VO NG = = VI RF 1 + RF + RI NG RF + RI 1 + Z(S) RG 1+ Z(S) OPERATING SUGGESTIONS SETTING RESISTOR VALUES TO OPTIMIZE BANDWIDTH A current-feedback op amp like the OPA2691 can hold an almost constant bandwidth over signal gain settings with the proper adjustment of the external resistor values. This is shown in the Typical Characteristics; the small-signal bandwidth decreases only slightly with increasing gain. Those curves also show that the feedback resistor has been changed for each gain setting. The resistor values on the inverting side of the circuit for a current-feedback op amp can be treated as frequency response compensation elements while their ratios set the signal gain. Figure 7 shows the small-signal frequency response analysis circuit for the OPA2691. This is written in a loop-gain analysis format where the errors arising from a non-infinite open-loop gain are shown in the denominator. If Z(S) were infinite over all frequencies, the denominator of Equation 1 would reduce to 1 and the ideal desired signal gain shown in the numerator would be achieved. The fraction in the denominator of Equation 1 determines the frequency response. Equation 2 shows this as the loop-gain equation: Z(S) RF + RI NG VO IERR Z(S) IERR RF RG FIGURE 7. Current-Feedback Transfer Function Analysis Circuit. The key elements of this current-feedback op amp model are: Buffer gain from the noninverting input to the inverting input RI Buffer output impedance iERR Feedback error current signal Z(s) Frequency dependent open-loop transimpedance gain from iERR to VO The buffer gain is typically very close to 1.00 and is normally neglected from signal gain considerations. It will, however, set the CMRR for a single op amp differential amplifier configuration. For a buffer gain < 1.0, the CMRR = -20 * log (1 - )dB. (2) The OPA2691 is internally compensated to give a maximally flat frequency response for RF = 402 at NG = 2 on 5V supplies. Evaluating the denominator of Equation 2 (which is the feedback transimpedance) gives an optimal target of 476. As the signal gain changes, the contribution of the NG * RI term in the feedback transimpedance will change, but the total can be held constant by adjusting RF. Equation 3 gives an approximate equation for optimum RF over signal gain: RF = 476 - NG RI (3) As the desired signal gain increases, this equation will eventually predict a negative RF. A somewhat subjective limit to this adjustment can also be set by holding RG to a minimum value of 20. Lower values will load both the buffer stage at the input and the output stage if RF gets too low--actually decreasing OPA2691 SBOS224D = Loop Gain If 20 * log(RF + NG * RI) were drawn on top of the open-loop transimpedance plot, the difference between the two would be the loop gain at a given frequency. Eventually, Z(S) rolls off to equal the denominator of Equation 2 at which point the loop gain has reduced to 1 (and the curves have intersected). This point of equality is where the amplifier's closed-loop frequency response given by Equation 1 will start to roll off, and is exactly analogous to the frequency at which the noise gain equals the open-loop voltage gain for a voltage-feedback op amp. The difference here is that the total impedance in the denominator of Equation 2 may be controlled somewhat separately from the desired signal gain (or NG). VI RI (1) R NG 1 + F RG www.ti.com 15 the bandwidth. Figure 8 shows the recommended RF versus NG for both 5V and a single +5V operation. The values for RF versus Gain shown here are approximately equal to the values used to generate the Typical Characteristics. They differ in that the optimized values used in the Typical Characteristics are also correcting for board parasitics not considered in the simplified analysis leading to Equation 3. The values shown in Figure 8 give a good starting point for design where bandwidth optimization is desired. +5V Power-supply decoupling not shown. 50 Load 1/2 OPA2691 50 Source VO 50 RF 374 RG 182 VI RM 68.1 600 Feedback Resistor () 500 -5V 400 FIGURE 9. Inverting Gain of -2 with Impedance Matching. +5V 300 200 5V 100 0 0 5 10 15 20 Noise Gain FIGURE 8. Recommended Feedback Resistor vs Noise Gain. The total impedance going into the inverting input may be used to adjust the closed-loop signal bandwidth. Inserting a series resistor between the inverting input and the summing junction will increase the feedback impedance (denominator of Equation 2), decreasing the bandwidth. The internal buffer output impedance for the OPA2691 is slightly influenced by the source impedance looking out of the noninverting input terminal. High source resistors will have the effect of increasing RI, decreasing the bandwidth. For those single-supply applications which develop a midpoint bias at the noninverting input through high valued resistors, the decoupling capacitor is essential for power-supply ripple rejection, noninverting input noise current shunting, and to minimize the highfrequency value for RI in Figure 7. INVERTING AMPLIFIER OPERATION Since the OPA2691 is a general-purpose, wideband currentfeedback op amp, most of the familiar op amp application circuits are available to the designer. Those dual op amp applications that require considerable flexibility in the feedback element (for example, integrators, transimpedance, and some filters) should consider the unity-gain stable voltagefeedback OPA2690, since the feedback resistor is the compensation element for a current-feedback op amp. Wideband inverting operation (and especially summing) is particularly suited to the OPA2691. Figure 9 shows a typical inverting configuration where the I/O impedances and signal gain from Figure 1 are retained in an inverting circuit configuration. In the inverting configuration, two key design considerations must be noted. The first is that the gain resistor (RG) becomes part of the signal channel input impedance. If input 16 impedance matching is desired (which is beneficial whenever the signal is coupled through a cable, twisted-pair, long PCB trace, or other transmission line conductor), it is normally necessary to add an additional matching resistor to ground. RG by itself is normally not set to the required input impedance since its value, along with the desired gain, will determine an RF which may be non-optimal from a frequency response standpoint. The total input impedance for the source becomes the parallel combination of RG and RM. The second major consideration, touched on in the previous paragraph, is that the signal source impedance becomes part of the noise gain equation and will have slight effect on the bandwidth through Equation 1. The values shown in Figure 9 have accounted for this by slightly decreasing RF (from Figure 1) to re-optimize the bandwidth for the noise gain of Figure 9 (NG = 2.74) In the example of Figure 9, the RM value combines in parallel with the external 50 source impedance, yielding an effective driving impedance of 50 || 68 = 28.8. This impedance is added in series with RG for calculating the noise gain--which gives NG = 2.74. This value, along with the RF of Figure 8 and the inverting input impedance of 37, are inserted into Equation 3 to get a feedback transimpedance nearly equal to the 476 optimum value. Note that the noninverting input in this bipolar supply inverting application is connected directly to ground. It is often suggested that an additional resistor be connected to ground on the noninverting input to achieve bias current error cancellation at the output. The input bias currents for a currentfeedback op amp are not generally matched in either magnitude or polarity. Connecting a resistor to ground on the noninverting input of the OPA2691 in the circuit of Figure 9 will actually provide additional gain for that input's bias and noise currents, but will not decrease the output DC error since the input bias currents are not matched. OUTPUT CURRENT AND VOLTAGE The OPA2691 provides output voltage and current capabilities that are unsurpassed in a low-cost, dual monolithic op amp. Under no-load conditions at 25C, the output voltage typically swings closer than 1V to either supply rail; the tested OPA2691 www.ti.com SBOS224D swing limit is within 1.2V of either rail. Into a 15 load (the minimum tested load), it is tested to deliver more than 160mA. and adds a zero at a higher frequency. The additional zero acts to cancel the phase lag from the capacitive load pole, thus increasing the phase margin and improving stability. The specifications described above, though familiar in the industry, consider voltage and current limits separately. In many applications, it is the voltage x current, or V-I product, which is more relevant to circuit operation. Refer to the Output Voltage and Current Limitations plot in the Typical Characteristics. The X- and Y-axes of this graph show the zero-voltage output current limit and the zero-current output voltage limit, respectively. The four quadrants give a more detailed view of the OPA2691's output drive capabilities, noting that the graph is bounded by a Safe Operating Area of 1W maximum internal power dissipation (in this case for 1 channel only). Superimposing resistor load lines onto the plot shows that the OPA2691 can drive 2.5V into 25 or 3.5V into 50 without exceeding the output capabilities or the 1W dissipation limit. A 100 load line (the standard test circuit load) shows the full 3.9V output swing capability, as shown in the Electrical Characteristics. The Typical Characteristics show the recommended RS vs Capacitive Load and the resulting frequency response at the load. Parasitic capacitive loads greater than 2pF can begin to degrade the performance of the OPA2691. Long PC board traces, unmatched cables, and connections to multiple devices can easily cause this value to be exceeded. Always consider this effect carefully, and add the recommended series resistor as close as possible to the OPA2691 output pin (see Board Layout Guidelines). The minimum specified output voltage and current over temperature are set by worst-case simulations at the cold temperature extreme. Only at cold start-up will the output current and voltage decrease to the numbers shown in the electrical characteristic tables. As the output transistors deliver power, their junction temperatures will increase, decreasing their VBEs (increasing the available output voltage swing) and increasing their current gains (increasing the available output current). In steady-state operation, the available output voltage and current will always be greater than that shown in the over-temperature specifications since the output stage junction temperatures will be higher than the minimum specified operating ambient. To protect the output stage from accidental shorts to ground and the power supplies, output short-circuit protection is included in the OPA2691. The circuit acts to limit the maximum source or sink current to approximately 250mA. DRIVING CAPACITIVE LOADS One of the most demanding and yet very common load conditions for an op amp is capacitive loading. Often, the capacitive load is the input of an ADC--including additional external capacitance which may be recommended to improve the ADC's linearity. A high-speed, high open-loop gain amplifier like the OPA2691 can be very susceptible to decreased stability and closed-loop response peaking when a capacitive load is placed directly on the output pin. When the amplifier's open-loop output resistance is considered, this capacitive load introduces an additional pole in the signal path that can decrease the phase margin. Several external solutions to this problem have been suggested. When the primary considerations are frequency response flatness, pulse response fidelity, and/or distortion, the simplest and most effective solution is to isolate the capacitive load from the feedback loop by inserting a series isolation resistor between the amplifier output and the capacitive load. This does not eliminate the pole from the loop response, but rather shifts it DISTORTION PERFORMANCE The OPA2691 provides good distortion performance into a 100 load on 5V supplies. Relative to alternative solutions, it provides exceptional performance into lighter loads and/or operating on a single +5V supply. Generally, until the fundamental signal reaches very high frequency or power levels, the 2nd-harmonic will dominate the distortion with a negligible 3rd-harmonic component. Focusing then on the 2nd-harmonic, increasing the load impedance improves distortion directly. Remember that the total load includes the feedback network--in the noninverting configuration (see Figure 1) this is the sum of RF + RG, while in the inverting configuration it is just RF. Also, providing an additional supply decoupling capacitor (0.01F) between the supply pins (for bipolar operation) improves the 2nd-order distortion slightly (3dB to 6dB). In most op amps, increasing the output voltage swing increases harmonic distortion directly. The Typical Characteristics show the 2nd-harmonic increasing at a little less than the expected 2x rate while the 3rd-harmonic increases at a little less than the expected 3x rate. Where the test power doubles, the difference between it and the 2nd-harmonic decreases less than the expected 6dB while the difference between it and the 3rd-harmonic decreases by less than the expected 12dB. This also shows up in the 2-tone, 3rd-order intermodulation spurious (IM3) response curves. The 3rdorder spurious levels are extremely low at low output power levels. The output stage continues to hold them low even as the fundamental power reaches very high levels. As the Typical Characteristics show, the spurious intermodulation powers do not increase as predicted by a traditional intercept model. As the fundamental power level increases, the dynamic range does not decrease significantly. For two tones centered at 20MHz, with 10dBm/tone into a matched 50 load (i.e., 2Vp-p for each tone at the load, which requires 8Vp-p for the overall 2-tone envelope at the output pin), the Typical Characteristics show 48dBc difference between the test-tone power and the 3rd-order intermodulation spurious levels. This exceptional performance improves further when operating at lower frequencies. NOISE PERFORMANCE Wideband current-feedback op amps generally have a higher output noise than comparable voltage-feedback op amps. The OPA2691 offers an excellent balance between voltage and OPA2691 SBOS224D www.ti.com 17 current noise terms to achieve low output noise. The inverting current noise (15pA/Hz) is significantly lower than earlier solutions while the input voltage noise (1.7nV/Hz) is lower than most unity-gain stable, wideband, voltage-feedback op amps. This low input voltage noise was achieved at the price of higher noninverting input current noise (12pA/Hz). As long as the AC source impedance looking out of the noninverting node is less than 100, this current noise will not contribute significantly to the total output noise. The op amp input voltage noise and the two input current noise terms combine to give low output noise under a wide variety of operating conditions. Figure 10 shows the op amp noise analysis model with all the noise terms included. In this model, all noise terms are taken to be noise voltage or current density terms in either nV/Hz or pA/Hz. ENI A current-feedback op amp like the OPA2691 provides exceptional bandwidth in high gains, giving fast pulse settling but only moderate DC accuracy. The Electrical Characteristics show an input offset voltage comparable to high-speed voltage-feedback amplifiers. However, the two input bias currents are somewhat higher and are unmatched. Whereas bias current cancellation techniques are very effective with most voltage-feedback op amps, they do not generally reduce the output DC offset for wideband current-feedback op amps. Since the two input bias currents are unrelated in both magnitude and polarity, matching the source impedance looking out of each input to reduce their error contribution to the output is ineffective. Evaluating the configuration of Figure 1, using worst-case +25C input offset voltage and the two input bias currents, gives a worst-case output offset range equal to: (NG * VOS(MAX)) + (IBN * RS/2 * NG) (IBI * RF) 1/2 OPA2691 RS DC ACCURACY AND OFFSET CONTROL EO IBN where NG = noninverting signal gain = (2 * 3.0mV) + (35A * 25 * 2) (402 * 25A) = 6mV + 1.75mV 10.05mV = -14.3mV +17.8mV ERS RF 4kTRS 4kT RG IBI RG DISABLE OPERATION (SO-14 ONLY) 4kTRF 4kT = 1.6E -20J at 290K FIGURE 10. Op Amp Noise Analysis Model. The total output spot noise voltage can be computed as the square root of the sum of all squared output noise voltage contributors. Equation 4 shows the general form for the output noise voltage using the terms shown in Figure 10. The OPA2691I-14D provides an optional disable feature that may be used either to reduce system power or to implement a simple channel multiplexing operation. If the DIS control pin is left unconnected, the OPA2691I-14D will operate normally. To disable, the control pin must be asserted low. Figure 11 shows a simplified internal circuit for the disable control feature. +VS (4) EO = (E NI 2 ) + (IBN RS )2 + 4kTRS NG2 + (IBI RF )2 + 4kTRF NG 15k Dividing this expression by the noise gain (NG = (1 + RF/RG)) will give the equivalent input referred spot noise voltage at the noninverting input, as shown in Equation 5. I R 2 4kTRF EN = ENI 2 + (IBN RS )2 + 4kTRS + BI F + NG NG (5) Evaluating these two equations for the OPA2691 circuit and component values presented in Figure 1 will give a total output spot noise voltage of 8.08nV/Hz and a total equivalent input spot noise voltage of 4.04nV/Hz. This total input referred spot noise voltage is higher than the 1.7nV/Hz specification for the op amp voltage noise alone. This reflects the noise added to the output by the inverting current noise times the feedback resistor. If the feedback resistor is reduced in high-gain configurations (as suggested previously), the total input referred voltage noise given by Equation 5 will approach just the 1.7nV/Hz of the op amp itself. For example, going to a gain of +10 using RF = 180 will give a total input referred noise of 2.1nV/Hz. 18 Q1 25k VDIS 110k IS Control -VS FIGURE 11. Simplified Disable Control Circuit, Each Channel. In normal operation, base current to Q1 is provided through the 110k resistor while the emitter current through the 15k resistor sets up a voltage drop that is inadequate to turn on the two diodes in Q1's emitter. As V DIS is pulled low, additional current is pulled through the 15k resistor, eventually turning on these two diodes ( 100A). At this point, any further current pulled out of V DIS goes through those diodes OPA2691 www.ti.com SBOS224D holding the emitter-base voltage of Q1 at approximately 0V. This shuts off the collector current out of Q1, turning the amplifier off. The supply currents in the disable mode are only those required to operate the circuit of Figure 11. Additional circuitry ensures that turn-on time occurs faster than turn-off time (make-before-break). When disabled, the output and input nodes go to a high impedance state. If the OPA2691 is operating in a gain of +1, this will show a very high impedance (4pF || 1M) at the output and exceptional signal isolation. If operating at a gain greater than +1, the total feedback network resistance (RF + RG) will appear as the impedance looking back into the output, but the circuit will still show very high forward and reverse isolation. If configured as an inverting amplifier, the input and output will be connected through the feedback network resistance (RF + RG) giving relatively poor input to output isolation. deliver load power. Quiescent power is simply the specified no-load supply current times the total supply voltage across the part. PDL will depend on the required output signal and load but would, for a grounded resistive load, be at a maximum when the output is fixed at a voltage equal to 1/2 of either supply voltage (for equal bipolar supplies). Under this condition, PDL = VS2/(4 * RL) where RL includes feedback network loading. Note that it is the power in the output stage and not into the load that determines internal power dissipation. As a worst-case example, compute the maximum TJ using an OPA2691 SO-8 in the circuit of Figure 1 operating at the maximum specified ambient temperature of +85C with both outputs driving a grounded 20 load to +2.5V. PD = 10V * 11.5mA + 2 * [52/(4 * (20 || 804))] = 756mW Maximum TJ = +85C + (0.756 * 125C/W) = 179.5C The transition edge rate (dv/dt) of the DIS control line will influence this glitch. For the plot of Figure 12, the edge rate was reduced until no further reduction in glitch amplitude was observed. This approximately 1V/ns maximum slew rate may be achieved by adding a simple RC filter into the VDIS pin from a higher speed logic line. If extremely fast transition logic is used, a 2k series resistor between the logic gate and the V DIS input pin will provide adequate bandlimiting using just the parasitic input capacitance on the V DIS pin while still ensuring adequate logic level swing. BOARD LAYOUT GUIDELINES 6.0 4.0 2.0 Output Voltage (10mV/div) 0.0 VDIS (2V/div) One key parameter in disable operation is the output glitch when switching in and out of the disabled mode. Figure 12 shows these glitches for the circuit of Figure 1 with the input signal set to 0V. The glitch waveform at the output pin is plotted along with the DIS pin voltage. This absolute worst-case condition exceeds specified maximum junction temperature. Normally this extreme case will not be encountered. Careful attention to internal power dissipation is required. 30 20 10 0 -10 -20 -30 Time (20ns/div) FIGURE 12. Disable/Enable Glitch. THERMAL ANALYSIS Due to the high output power capability of the OPA2691, heatsinking or forced airflow may be required under extreme operating conditions. Maximum desired junction temperature will set the maximum allowed internal power dissipation as described below. In no case should the maximum junction temperature be allowed to exceed 175C. Operating junction temperature (TJ) is given by TA + PD * JA. The total internal power dissipation (PD) is the sum of quiescent power (PDQ) and additional power dissipation in the output stage (PDL) to Achieving optimum performance with a high-frequency amplifier like the OPA2691 requires careful attention to board layout parasitics and external component types. Recommendations that will optimize performance include: a) Minimize parasitic capacitance to any AC ground for all of the signal I/O pins. Parasitic capacitance on the output and inverting input pins can cause instability: on the noninverting input, it can react with the source impedance to cause unintentional bandlimiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground and power planes should be unbroken elsewhere on the board. b) Minimize the distance (< 0.25") from the power-supply pins to high-frequency 0.1F decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. The power-supply connections (on pins 4 and 7) should always be decoupled with these capacitors. An optional supply decoupling capacitor across the two power supplies (for bipolar operation) will improve 2nd-harmonic distortion performance. Larger (2.2F to 6.8F) decoupling capacitors, effective at lower frequency, should also be used on the main supply pins. These may be placed somewhat farther from the device and may be shared among several devices in the same area of the PCB. c) Careful selection and placement of external components will preserve the high-frequency performance of the OPA2691. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a tighter overall layout. Metal film and carbon composition axiallyleaded resistors can also provide good high-frequency performance. Again, keep their leads and PCB trace length as OPA2691 SBOS224D www.ti.com 19 short as possible. Never use wirewound type resistors in a high-frequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the feedback and series output resistor, if any, as close as possible to the output pin. Other network components, such as noninverting input termination resistors, should also be placed close to the package. Where double-side component mounting is allowed, place the feedback resistor directly under the package on the other side of the board between the output and inverting input pins. The frequency response is primarily determined by the feedback resistor value as described previously. Increasing its value will reduce the bandwidth, while decreasing it will give a more peaked frequency response. The 402 feedback resistor used in the electrical characteristics at a gain of +2 on 5V supplies is a good starting point for design. Note that a 453 feedback resistor, rather than a direct short, is recommended for the unity-gain follower application. A current-feedback op amp requires a feedback resistor even in the unity-gain follower configuration to control stability. d) Connections to other wideband devices on the board may be made with short direct traces or through onboard transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50mils to 100mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RS from the plot of Recommended RS vs Capacitive Load. Low parasitic capacitive loads (< 5pF) may not need an RS since the OPA2691 is nominally compensated to operate with a 2pF parasitic load. If a long trace is required, and the 6dB signal loss intrinsic to a doubly-terminated transmission line is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). A 50 environment is normally not necessary on board, and in fact a higher impedance environment will improve distortion as shown in the Distortion vs Load plots. With a characteristic board trace impedance defined based on board material and trace dimensions, a matching series resistor into the trace from the output of the OPA2691 is used as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance will be the parallel combination of the shunt resistor and the input impedance of the destination device: this total effective impedance should be set to match the trace impedance. The high output voltage and current capability of the OPA2691 allows multiple destination devices to be handled 20 as separate transmission lines, each with their own series and shunt terminations. If the 6dB attenuation of a doublyterminated transmission line is unacceptable, a long trace can be series-terminated at the source end only. Treat the trace as a capacitive load in this case and set the series resistor value as shown in the plot of RS vs Capacitive Load. This will not preserve signal integrity as well as a doublyterminated line. If the input impedance of the destination device is low, there will be some signal attenuation due to the voltage divider formed by the series output into the terminating impedance. e) Socketing a high-speed part like the OPA2691 is not recommended. The additional lead length and pin-to-pin capacitance introduced by the socket can create an extremely troublesome parasitic network which can make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by soldering the OPA2691 onto the board. INPUT AND ESD PROTECTION The OPA2691 is built using a very high-speed complementary bipolar process. The internal junction breakdown voltages are relatively low for these very small geometry devices. These breakdowns are reflected in the Absolute Maximum Ratings table. All device pins have limited ESD protection using internal diodes to the power supplies, as shown in Figure 13. These diodes provide moderate protection to input overdrive voltages above the supplies as well. The protection diodes can typically support 30mA continuous current. Where higher currents are possible (for example, in systems with 15V supply parts driving into the OPA2691), current-limiting series resistors should be added into the two inputs. Keep these resistor values as low as possible since high values degrade both noise performance and frequency response. +V CC External Pin Internal Circuitry -V CC FIGURE 12. Internal ESD Protection. OPA2691 www.ti.com SBOS224D Revision History DATE REVISION 7/08 D 2/07 C PAGE SECTION 2 Abs Max Ratings 3, 4 Electrical Characteristics, Power Supply 8 Typical Characteristics DESCRIPTION Changed Storage Temperature Range from -40C to +125C to -65C to +125C. Added minimum supply voltage. Changed Closed-Loop Output Impedance vs Frequency plot. NOTE: Page numbers for previous revisions may differ from page numbers in the current version. OPA2691 SBOS224D www.ti.com 21 PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) OPA2691I-14D ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2691I-14DG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2691I-14DR ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2691I-14DRG4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2691ID ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2691IDG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2691IDR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA2691IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 23-Apr-2011 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant OPA2691I-14DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 OPA2691IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA2691I-14DR SOIC D 14 2500 367.0 367.0 38.0 OPA2691IDR SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated