QES050YE-AN83V - Power-One - Datasheet.Directory

REV. AUG 20, 2003

Notes

12345678910

X10 = LOAD %

EFFICIENCY %

OES021ZC-A

OES025ZD-A

OES033ZE-A

OES040ZG-A

Technical Specifications

• Industry Standard Package

• 100°C Case Operation

• Optional Trim and Enable

• Wide Range Input Voltage

• 1500V Isolation

• Short Circuit Protection

Description

Features

Turn-On Time 30 ms

Remote Shutdown Positive or Negative Logic

Remote Shutdown Reference Vin Negative

Switching Frequency 300 kHz

Isolation

Input - Output 1500 VDC

Input - Case 1050 VDC

Output - Case 1050 VDC

Temperature Coefficient ±0.02%/°C

Case Temperature

Operating Range -40 To +100°C

Storage Range -40 To +125°C

Thermal Shutdown Range 105 to 115°C

Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz

MTBF†(Bellcore TR-NWT-000332) 2.5 X 106hrs

Safety UL, cUL, TUV

Weight (Approx.) 1.7 oz

Setpoint Accuracy ±1%

Line Regulation Vin Min. - Vin Max., Iout Rated 0.2% Vout

Load Regulation Iout Min. - Iout Max., Vin Nom. 0.5% Vout

Remote Sense Headroom 0.5 VDC

Minimum Output Current 10 %, Iout Rated

Dynamic Regulation, Loadstep 25% Iout

Pk Deviation 4% Vout

Settling Time 500 ms

Voltage Trim Range ±10%

Short Circuit And Overcurrent Protection Shutdown

Short Circuit Current Limit 200% Iout

Current Limit Threshold Range, % of Iout Rated 110 - 140%

OVP Trip Range 115 - 140% Vout Nom.

UVP Trip Range 70 - 90% Vout Nom.

OVP/UVP Type Latching

Voltage Range

24 VDC Nominal 18 - 36 VDC

48 VDC Nominal 36 - 75 VDC

Input Reverse Input Current Shunt Diode

QES single output DC/DC converters provide up to 66 watts of output power in an industry-standard, quarter-brick

package. The QES converters feature open-frame packaging, along with planar magnetics and a high efficiency

topology to provide maximum useable power with minimal thermal constraints. The QES is suited to telecom,

networking, and industrial applications, and is fully compatible with production board washing processes.

Input

Output

Efficiency vs. Load (48V Input)

General

†MTBF predictions may vary slightly from model to model.

Specifications typically at 25°C, normal line, and full load, unless

otherwise stated.

Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible

with commercial wave-soldering equipment.

Safety: Agency approvals may vary from model to model. Please

consult factory for specific model information.

Units are water-washable and fully compatible with commercial spray

or immersion post wave-solder washing equipment.

QES DC/DC Series Data Sheet

Page 1 of 3

QES DC/DC Series Data Sheet

REV. AUG 20, 2003

MODEL INPUT VOLTAGE INPUT VOLTAGE MAXIMUM INPUT OUTPUT RATED OUTPUT RIPPLE & NOISE TYPICAL

(VOLTS) RANGE (VOLTS) CURRENT (AMPS)* VOLTAGE (VOLTS) CURRENT (AMPS) pk-pk (mV) EFFICIENCY**

QES050YE-A 24 18-36 3.3 3.3 15 100 85%

QES066YE-A 24 18-36 4.4 3.3 20 100 85%

QES036ZB-A 48 36-75 1.4 1.8 20 75 76%

QES038ZD-A 48 36-75 1.4 2.5 15 100 85%

QES050ZD-A 48 36-75 1.8 2.5 20 100 83%

QES050ZE-A 48 36-75 1.6 3.3 15 100 86%

QES066ZE-A 48 36-75 2.2 3.3 20 100 86%

NOTES:

* Maximum input current at minimum input voltage, maximum rated output power.

** At nominal Vin, rated output.

Thermal Impedance

Note:

Thermal impedance data is dependent

on many environmental factors. The

exact thermal performance should be

validated for specific application.

Natural Convection 10.1 °C/W

100 LFM 8.0 °C/W

200 LFM 5.4 °C/W

300 LFM 4.4 °C/W

400 LFM 3.4 °C/W

1-V

in 0.040"

2 On/Off 0.040"

3+V

in 0.040"

4-V

out 0.062"

5 -Sense 0.040"

6 Trim 0.040"

7 +Sense 0.040"

8+V

out 0.062"

Pin Function Pin Diameter

(12.7mm)

0.50"

(1.6mm)

-0.425"(-10.8mm)

0.895"(22.7mm)

0.450"(11.4mm)

0.150"(3.8mm)

-0.295"(-7.5mm)

0.600"(15.2mm)

0.300"(7.6mm)

0.18"(4.6mm)

M2X0.4 THROUGH 2PL

MOUNTING INSERTS

DIA 0.062"

DIA 0.040"

(1.0mm)

2.28"

(57.9mm)

1.45"

(36.8mm)

BOTTOM VIEW

-0.14"

(-3.6mm) 2.010"

(51.1mm)

(-0.3mm)

-0.010"

(50.8mm)

2.000"

Tolerances

Inches: (Millimeters)

.XX ± 0.020 .X ± 0.5

.XXX ± 0.010 .XX ± 0.25

Pin:

± 0.002 ± 0.05

(Dimensions as listed unless

otherwise specified.)

Mechanical Drawing

Model Selection

Page 2 of 3

REV. AUG 20, 2003

NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not authorized for use as critical components in life support systems,

equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of

Power-One, Inc.

TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.

OPTION SUFFIX APPLICABLE SERIES REMARKS

Negative Logic N HAS, HBD, HBS, HES, HLS, HLD, LES, TTL "Low" Turns Module ON

QBS, QES, QLS, TES, TQD TTL "High" Turns Module OFF

Lucent-Compatible Trim T HAS, HBD, HBS, HES, HLS, QBS, QES,

QLS

Trim 1 IAS, LES

Enable 2 IAD, IAS, LES, SMS

Trim and Enable 3 IAS, LES

Pin Length and Heatsink Options Standard Pin Length is 0.180" (4.6mm)

0.110" (2.8mm) Pin Length 8 All Leaded Models

0.150" (3.8mm) Pin Length 9 All Leaded Models

0.24" (6.1mm) Horizontal Heatsink 1H All 1/4-Bricks, 1/2-Bricks, 3/4-Bricks, Full-Bricks Includes Thermal Pad