PAA150PTR - Clare - Datasheet.Directory

www.clare.com

DS-PAA150-R05 1

PAA150

Dual Single-Pole, Normally Open

OptoMOS® Relays

RoHS

2002/95/EC e3

Part # Description

PAA150 8-Lead DIP (50/tube)

PAA150P 8-Lead Flatpack (50/tube)

PAA150PTR 8-Lead Flatpack (1000/Reel)

PAA150S 8-Lead Surface Mount (50/tube)

PAA150STR 8-Lead Surface Mount (1000/Reel)

Parameter Rating Units

Load Voltage 250 VP

Load Current 250 mA

Max RON 7Ω

Applications

Features

Description

Ordering Information

Pin Configuration

• Telecommunications

• Telecom Switching

• Tip/Ring Circuits

• Modem Switching (Laptop, Notebook, Pocket Size)

• Hook Switch

• Dial Pulsing

• Ground Start

• Ringing Injection

• Instrumentation

• Multiplexers

• Data Acquisition

• Electronic Switching

• I/O Subsystems

• Meters (Watt-Hour, Water, Gas)

• Medical Equipment-Patient/Equipment Isolation

• Security

• Aerospace

• Industrial Controls

• 3750Vrms Input/Output Isolation

• Small 8-Pin Packages

• Low Drive Power Requirements (TTL/CMOS

Compatible)

• No Moving Parts

• High Reliability

• Arc-Free With No Snubbing Circuits

• FCC Compatible

• VDE Compatible

• No EMI/RFI Generation

• Machine Insertable, Wave Solderable

• Tape & Reel Versions Available

The PAA150 is a dual, 250V, 250mA, 7Ω, normally

open (1-Form-A) relay that uses Clare's patented

OptoMOS architecture to provide 3750Vrms of input

to output isolation.

This high performance leader provides a more cost

effective solution where very low on-resistance is

required, but enhanced peak load voltage is not

required.

Approvals

• UL Recognized Component: File E76270

• CSA Certified Component: Certificate 1175739

• EN/IEC 60950-1 Certified Component:

TUV Certificate B 09 07 49410 004

Switching Characteristics

of Normally Open Devices

Form-A

ILOAD

10%

90%

ton toff

+ Control - Switch #1

- Control - Switch #1

+ Control - Switch #2

- Control - Switch #2

Load - Switch #1

AC/DC Configuration

Load - Switch #1

Load - Switch #2

www.clare.com

2R05

PAA150

Absolute Maximum Ratings are stress ratings. Stresses in

excess of these ratings can cause permanent damage to

the device. Functional operation of the device at conditions

beyond those indicated in the operational sections of this

data sheet is not implied.

Absolute Maximum Ratings @ 25ºC

Parameter Ratings Units

Blocking Voltage 250 VP

Reverse Input Voltage 5 V

Input Control Current 50 mA

Peak (10ms) 1 A

Input Power Dissipation 1150 mW

Total Power Dissipation 2800 mW

Isolation Voltage, Input to Output 3750 Vrms

Operational Temperature -40 to +85 °C

Storage Temperature -40 to +125 °C

1 Derate linearly 1.33 mW / ºC

2 Derate linearly 6.67 mW / ºC

Electrical Characteristics @ 25ºC

Parameter Conditions Symbol Min Typ Max Units

Output Characteristics

Load Current

Continuous * - IL- - 250 mA

Peak 10ms ILPK - - 500

On-Resistance, AC/DC Configuration IL=250mA RON --7Ω

Off-State Leakage Current VL=250VPILEAK --1µA

Switching Speeds

Turn-On IF=5mA, VL=10V ton - - 2.5 ms

Turn-Off toff - - 0.5

Output Capacitance VL=50V, f=1MHz COUT - 110 - pF

Input Characteristics

Input Control Current IL=250mA IF--5mA

Input Dropout Current - IF0.4 0.7 - mA

Input Voltage Drop IF=5mA VF0.9 1.2 1.4 V

Reverse Input Current VR=5V IR- - 10 µA

Common Characteristics

Capacitance Input to Output - CI/O -3-pF

*NOTE: If both poles operate simultaneously, then load current must be derated so as not to exceed the package power dissipation value.

PAA150

www.clare.com 3

R05

Manufacturing Information

Moisture Sensitivity

All plastic encapsulated semiconductor packages are susceptible to moisture ingression. Clare classified all

of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry

standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to

the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled

according to the limitations and information in that standard as well as to any limitations set forth in the information or

standards referenced below.

Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced

product performance, reduction of operable life, and/or reduction of overall reliability.

This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according

to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.

Device Moisture Sensitivity Level (MSL) Rating

PAA150 / PAA150S / PAA150P MSL 1

ESD Sensitivity

This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.

Reflow Profile

This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020

must be observed.

Device Maximum Temperature x Time

PAA150 / PAA150S 250ºC for 30 seconds

PAA150P 260ºC for 30 seconds

Board Wash

Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is

acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated

products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes.

Chlorine-based or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic

energy should not be used.

RoHS

2002/95/EC e3

www.clare.com

4R05

PAA150

MECHANICAL DIMENSIONS

Dimensions

(inches)

PCB Hole Pattern

2.540 ± 0.127

(0.100 ± 0.005)

6.350 ± 0.127

(0.250 ± 0.005)

9.144 ± 0.508

(0.360 ± 0.020)

0.457 ± 0.076

(0.018 ± 0.003)

9.652 ± 0.381

(0.380 ± 0.015)

7.239 TYP.

(0.285)

7.620 ± 0.254

(0.300 ± 0.010)

4.064 TYP

(0.160)

0.889 ± 0.102

(0.035 ± 0.004)

8-0.800 DIA.

(8-0.031 DIA.) 2.540 ± 0.127

(0.100 ± 0.005)

7.620 ± 0.127

(0.300 ± 0.005)

7.620 ± 0.127

(0.300 ± 0.005)

6.350 ± 0.127

(0.250 ± 0.005)

3.302 ± 0.051

(0.130 ± 0.002)

0.254 TYP

(0.01)

Dimensions

(inches)

PCB Land Pattern

2.540 ± 0.127

(0.100 ± 0.005)

9.652 ± 0.381

(0.380 ± 0.015)

6.350 ± 0.127

(0.250 ± 0.005)

9.525 ± 0.254

(0.375 ± 0.010)

0.457 ± 0.076

(0.018 ± 0.003)

0.813 ± 0.120

(0.032 ± 0.004)

4.445 ± 0.127

(0.175 ± 0.005)

7.620 ± 0.254

(0.300 ± 0.010)

0.635 ± 0.127

(0.025 ± 0.005)

0.254 ± 0.127

(0.010 ± 0.0005)

2.54

(0.10)

8.90

(0.3503)

1.65

(0.0649)

0.65

(0.0255)

3.302 ± 0.051

(0.130 ± 0.002)

Dimensions

(inches)

PCB Land Pattern

9.398 ± 0.127

(0.370 ± 0.005)

6.350 ± 0.127

(0.250 ± 0.005)

2.540 ± 0.127

(0.100 ± 0.005)

7.620 ± 0.254

(0.300 ± 0.010)

0 MIN / 0.102 MAX

(0 MIN / 0.004 MAX)

2.286 MAX.

(0.090 MAX.)

0.203 ± 0.013

(0.008 ± 0.0005)

0.635 ± 0.127

(0.025 ± 0.005)

9.652 ± 0.381

(0.380 ± 0.015)

0.457 ± 0.076

(0.018 ± 0.003)

2.159 ± 0.025

(0.085 ± 0.001)

2.54

(0.10)

8.70

(0.3425)

1.55

(0.0610)

0.65

(0.0255)

0.864 ± 0.120

(0.034 ± 0.004)

PAA150

PAA150S

PAA150P

Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications

and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare’s Standard Terms and Conditions of

Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability,

fitness for a particular purpose, or infringement of any intellectual property right.

The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other

applications intended to support or sustain life, or where malfunction of Clare’s product may result in direct physical harm, injury, or death to a person or severe property or environmental

damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice.

Specification: DS-PAA150-R05

OptoMOS® is a registered trademark of Clare, Inc.

7/30/2010

For additional information please visit our website at: www.clare.com

PAA150

Dimensions

(inches)

User Direction of Feed

NOTES:

1. Dimensions carry tolerances of EIA Standard 481-2

2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2

Embossment

Embossed Carrier

Top Cover

Tape Thickness

0.102 MAX.

(0.004 MAX.)

330.2 DIA.

(13.00 DIA.)

K1=4.20

(0.165)

K =4.90

(0.193)

P=12.00

(0.472)

W=16.00

(0.63)

Bo=10.30

(0.406)

Ao=10.30

(0.406)

Dimensions

(inches)

NOTES:

1. All dimensions carry tolerances of EIA Standard 481-2

2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2

Embossment

Embossed Carrier

Top Cover

Tape Thickness

0.102 MAX.

(0.004 MAX.)

330.2 DIA.

(13.00 DIA.)

User Direction of Feed

P = 12.00

(0.472)

W = 16.00

(0.63)

Bo = 10.30

(0.406)

Ao = 10.30

(0.406)

K1= 2.00

(0.079)

K0= 2.70

(0.106)

PAA150S Tape & Reel

PAA150P Tape & Reel