ISL9R860P2, ISL9R860S3ST 8A, 600V StealthTM Diode General Description Features The ISL9R860P2, ISL9R860S2 and ISL9R860S3S are StealthTM diodes optimized for low loss performance in high frequency hard switched applications. The StealthTM family exhibits low reverse recovery current (IRRM) and exceptionally soft recovery under typical operating conditions. * Soft Recovery . . . . . . . . . . . . . . . . . . . tb / ta > 2.5 This device is intended for use as a free wheeling or boost diode in power supplies and other power switching applications. The low IRRM and short ta phase reduce loss in switching transistors. The soft recovery minimizes ringing, expanding the range of conditions under which the diode may be operated without the use of additional snubber circuitry. Consider using the StealthTM diode with an SMPS IGBT to provide the most efficient and highest power density design at lower cost. Formerly developmental type TA49409. * Fast Recovery . . . . . . . . . . . . . . . . . . . . trr < 25ns * Operating Temperature . . . . . . . . . . . . . . . 175oC * Reverse Voltage. . . . . . . . . . . . . . . . . . . . . . 600V * Avalanche Energy Rated Applications * Switch Mode Power Supplies * Hard Switched PFC Boost Diode * UPS Free Wheeling Diode * Motor Drive FWD * SMPS FWD * Snubber Diode Package Symbol JEDEC TO-220AC JEDEC TO-263AB K CATHODE (FLANGE) ANODE CATHODE CATHODE (FLANGE) N/C A ANODE Device Maximum Ratings TC= 25C unless otherwise noted Symbol VRRM VRWM VR Parameter Peak Repetitive Reverse Voltage Ratings 600 Units V Working Peak Reverse Voltage 600 V DC Blocking Voltage 600 V 8 A IF(AV) Average Rectified Forward Current (TC = 147oC) IFRM Repetitive Peak Surge Current (20kHz Square Wave) 16 A IFSM Nonrepetitive Peak Surge Current (Halfwave 1 Phase 60Hz) 100 A PD EAVL TJ, TSTG TL TPKG Power Dissipation 85 W Avalanche Energy (1A, 40mH) 20 mJ -55 to 175 C 300 260 C C Operating and Storage Temperature Range Maximum Temperature for Soldering Leads at 0.063in (1.6mm) from Case for 10s Package Body for 10s, See Techbrief TB334 CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. (c)2009 Fairchild Semiconductor Corporation ISL9R860P2, ISL9R860S3ST Rev. C2 ISL9R860P2, ISL9R860S3ST October 2009 Device Marking R860P2 R860S3S Device ISL9R860P2 Package TO-220AC Tape Width - Quantity - ISL9R860S3ST TO-263AB 24mm 800 Electrical Characteristics TC = 25C unless otherwise noted Symbol Parameter Test Conditions Min Typ Max Units Off State Characteristics IR Instantaneous Reverse Current TC = 25C - - 100 A TC = 125C - - 1.0 mA TC = 25C - 2.0 2.4 V TC = 125C - 1.6 2.0 V VR = 10V, IF = 0A - 30 - pF IF = 1A, dIF/dt = 100A/s, VR = 30V - 18 25 ns IF = 8A, dIF/dt = 100A/s, VR = 30V - 21 30 ns IF = 8A, dIF/dt = 200A/s, VR = 390V, TC = 25C - 28 - ns - 3.2 - A - 50 - nC - 77 - ns - 3.7 - - 3.4 - A - 150 - nC - 53 - ns - 2.5 - VR = 600V On State Characteristics VF Instantaneous Forward Voltage IF = 8A Dynamic Characteristics CJ Junction Capacitance Switching Characteristics trr trr Reverse Recovery Time Reverse Recovery Time IRRM Maximum Reverse Recovery Current QRR Reverse Recovery Charge trr Reverse Recovery Time S Softness Factor (tb/ta) IRRM Maximum Reverse Recovery Current QRR Reverse Recovery Charge trr Reverse Recovery Time S Softness Factor (tb/ta) IRRM Maximum Reverse Recovery Current QRR Reverse Recovery Charge dIM/dt IF = 8A, dIF/dt = 200A/s, VR = 390V, TC = 125C IF = 8A, dIF/dt = 600A/s, VR = 390V, TC = 125C Maximum di/dt during tb - 6.5 - A 195 - nC 500 - A/s Thermal Characteristics RJC Thermal Resistance Junction to Case - - 1.75 C/W RJA Thermal Resistance Junction to Ambient TO-220 - - 62 C/W RJA Thermal Resistance Junction to Ambient TO-263 62 C/W (c)2009 Fairchild Semiconductor Corporation ISL9R860P2, ISL9R860S3ST Rev. C2 ISL9R860P2, ISL9R860S3ST Package Marking and Ordering Information 16 100 IR, REVERSE CURRENT (A) IF, FORWARD CURRENT (A) 175oC 175oC 14 150oC 12 25oC 10 125oC 8 100oC 6 4 150oC 10 125oC 100oC 1 25oC 2 0 0 0.25 0.5 0.75 1 1.25 1.5 1.75 0.1 100 2.25 2.5 2.75 2 200 300 Figure 1. Forward Current vs Forward Voltage 600 90 VR = 390V, TJ = 125C VR = 390V, TJ = 125C 80 70 tb AT dIF/dt = 200A/s, 500A/s, 800A/s tb AT IF = 16A, 8A, 4A 70 60 t, RECOVERY TIMES (ns) t, RECOVERY TIMES (ns) 500 Figure 2. Reverse Current vs Reverse Voltage 80 50 40 30 20 10 2 4 6 8 10 12 50 40 30 20 ta AT IF = 16A, 8A, 4A 0 0 60 10 ta AT dIF/dt = 200A/s, 500A/s, 800A/s 14 0 100 16 200 IF, FORWARD CURRENT (A) Figure 3. ta and tb Curves vs Forward Current 11 VR = 390V, TJ = 125C dIF/dt = 800A/s 10 9 8 dIF/dt = 500A/s 7 6 5 dIF/dt = 200A/s 4 3 2 0 2 4 6 8 10 12 IF, FORWARD CURRENT (A) 14 16 Figure 5. Maximum Reverse Recovery Current vs Forward Current (c)2009 Fairchild Semiconductor Corporation 300 400 500 600 900 700 800 dIF /dt, CURRENT RATE OF CHANGE (A/s) 1000 Figure 4. ta and tb Curves vs dIF/dt IRRM , MAX REVERSE RECOVERY CURRENT (A) IRRM , MAX REVERSE RECOVERY CURRENT (A) 400 VR , REVERSE VOLTAGE (V) VF, FORWARD VOLTAGE (V) 14 VR = 390V, TJ = 125C 12 IF = 16A 10 IF = 8A 8 IF = 4A 6 4 2 0 100 200 300 400 500 600 700 800 900 1000 dIF /dt, CURRENT RATE OF CHANGE (A/s) Figure 6. Maximum Reverse Recovery Current vs dIF/dt ISL9R860P2, ISL9R860S2, ISL9R860S3ST Rev. C2 ISL9R860P2, ISL9R860S3ST Typical Performance Curves 350 S, REVERSE RECOVERY SOFTNESS FACTOR 6 QRR, REVERSE RECOVERY CHARGE (nC) VR = 390V, TJ = 125C 5 4 IF = 16A IF = 8A 3 IF = 4A 2 1 100 200 300 400 500 600 700 800 900 VR = 390V, TJ = 125C 300 IF = 16A 250 IF = 8A 200 150 IF = 4A 100 50 100 1000 dIF /dt, CURRENT RATE OF CHANGE (A/s) 500 600 700 800 900 1000 IF(AV), AVERAGE FORWARD CURRENT (A) 10 1000 800 600 400 200 0 0.1 1 10 100 VR , REVERSE VOLTAGE (V) Figure 9. Junction Capacitance vs Reverse Voltage 1.0 THERMAL IMPEDANCE 400 Figure 8. Reverse Recovery Charge vs dIF/dt 1200 CJ , JUNCTION CAPACITANCE (pF) 300 dIF /dt, CURRENT RATE OF CHANGE (A/s) Figure 7. Reverse Recovery Softness Factor vs dIF/dt ZJA, NORMALIZED 200 8 6 4 2 0 140 145 150 155 160 165 170 175 TC, CASE TEMPERATURE (oC) Figure 10. DC Current Derating Curve DUTY CYCLE - DESCENDING ORDER 0.5 0.2 0.1 0.05 0.02 0.01 PDM 0.1 t1 t2 NOTES: DUTY FACTOR: D = t1/t2 SINGLE PULSE PEAK TJ = PDM x ZJA x RJA + TA 0.01 10-5 10-4 10-3 10-2 10-1 t, RECTANGULAR PULSE DURATION (s) 100 101 Figure 11. Normalized Maximum Transient Thermal Impedance (c)2009 Fairchild Semiconductor Corporation ISL9R860P2, ISL9R860S2, ISL9R860S3ST Rev. C2 ISL9R860P2, ISL9R860S2, ISL9R860S3ST Typical Performance Curves (Continued) VGE AMPLITUDE AND RG CONTROL dIF/dt t1 AND t2 CONTROL IF L IF DUT RG VGE CURRENT SENSE trr dt ta tb 0 + VDD - MOSFET t1 dIF 0.25 IRM IRM t2 Figure 12. trr Test Circuit Figure 13. trr Waveforms and Definitions I = 1A L = 40mH R < 0.1 VDD = 50V EAVL = 1/2LI2 [VR(AVL) /(VR(AVL) - VDD)] Q1 = IGBT (BVCES > DUT VR(AVL)) L CURRENT SENSE Q1 VAVL R + IL VDD DUT t0 Figure 14. Avalanche Energy Test Circuit (c)2009 Fairchild Semiconductor Corporation IL I V t1 t2 t Figure 15. Avalanche Current and Voltage Waveforms ISL9R860P2, ISL9R860S3ST Rev. C2 ISL9R860P2, ISL9R860S3ST Test Circuits and Waveforms ISL9R860P2, ISL9R860S3ST Mechanical Dimensions TO-220AC Dimensions in Millimeters TO-263AB 10.67 9.65 -A- 12.70 1.68 1.00 4 9.45 9.65 8.38 10.00 (6.40) 1.78 MAX 2 3.80 3 1 1.05 1.78 1.14 0.99 0.51 (2.12) 5.08 5.08 0.25 B M LAND PATTERN RECOMMENDATION UNLESS NOTED, ALL DIMS TYPICAL AM -B6.22 MIN 4.83 4.06 1.65 1.14 4 6.86 MIN 15.88 14.61 SEE DETAIL A 2 3 1 GAGE PLANE 0.74 0.33 0.25 8 0 NOTES: UNLESS OTHERWISE SPECIFIED A) ALL DIMENSIONS ARE IN MILLIMETERS. B) REFERENCE JEDEC, TO-263, VARIATION AB. C) DIMENSIONING AND TOLERANCING PER ANSI Y14.5M - 1994. D) LOCATION OF THE PIN HOLE MAY VARY (LOWER LEFT CORNER, LOWER CENTER AND CENTER OF THE PACKAGE). E) LANDPATTERN RECOMMENDATION PER IPC TO254P1524X482-3N F) FILENAME: TO263A02REV6 0.10 2.79 1.78 0.25 MAX B 8 0 (5.38) SEATING PLANE Dimensions in Millimeters DETAIL A, ROTATED 90 SCALE: 2X ISL9R860P2, ISL9R860S3ST Mechanical Dimensions tm ISL9R860P2, ISL9R860S3ST TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not intended to be an exhaustive list of all such trademarks. PowerTrench(R) FPSTM AccuPowerTM The Power Franchise(R) F-PFSTM PowerXSTM Auto-SPMTM (R) FRFET(R) Programmable Active DroopTM Build it NowTM SM (R) Global Power Resource QFET CorePLUSTM TinyBoostTM Green FPSTM QSTM CorePOWERTM TinyBuckTM Green FPSTM e-SeriesTM Quiet SeriesTM CROSSVOLTTM TinyCalcTM GmaxTM RapidConfigureTM CTLTM TinyLogic(R) GTOTM Current Transfer LogicTM TINYOPTOTM IntelliMAXTM EcoSPARK(R) TM TinyPowerTM EfficentMaxTM Saving our world, 1mW /W /kW at a timeTM ISOPLANARTM TinyPWMTM EZSWITCHTM* SmartMaxTM MegaBuckTM TinyWireTM TM* SMART STARTTM MICROCOUPLERTM TriFault DetectTM SPM(R) MicroFETTM TRUECURRENTTM* STEALTHTM MicroPakTM (R) SuperFETTM MillerDriveTM (R) Fairchild SuperSOTTM-3 MotionMaxTM Fairchild Semiconductor(R) SuperSOTTM-6 UHC(R) Motion-SPMTM (R) FACT Quiet SeriesTM Ultra FRFETTM SuperSOTTM-8 OPTOLOGIC FACT(R) UniFETTM OPTOPLANAR(R) SupreMOSTM (R) (R) FAST VCXTM SyncFETTM FastvCoreTM VisualMaxTM Sync-LockTM FETBenchTM XSTM (R)* PDP SPMTM FlashWriter(R) * Power-SPMTM tm *Trademarks of System General Corporation, used under license by Fairchild Semiconductor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD'S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.Fairchildsemi.com, under Sales Support. Counterfeiting of semiconductor parts is a growing problem in the industry. All manufactures of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed application, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handing and storage and provide access to Fairchild's full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address and warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative / In Design Datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve the design. Obsolete Not In Production Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The datasheet is for reference information only. Rev. I41 www.fairchildsemi.com