Transient Voltage Suppression Diodes
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 03/28/18
Surface Mount – 600W > SMBJ-HR Series
Description
Agency Approvals
The SMBJ-HR High Reliability series is designed
specifically to protect sensitive electronic equipment from
voltage transients induced by lightning and other transient
voltage events.
Features
Excellent clamping
capability
Low incremental surge
resistance
Typical IR ≤ 1µA for VR >
11.10V
• SMT for minimal
board footprint
• Low profile package
Typical failure mode is
short from over-specified
voltage or current
Whisker test is conducted
based on JEDEC
JESD201A per its table 4a
and 4c
IEC-61000-4-2 ESD
15kV(Air), 8kV (Contact)
ESD protection of data
lines in accordance with
IEC 61000-4-2 (IEC801-2)
EFT protection of data
lines in accordance with
IEC 61000-4-4 (IEC801-4)
• Built-in strain relief
Fast response time:
typically less than 1.0ps
from 0V to BV min
• 600W peak pulse power
capability at 10/1000μs
waveform, repetition rate
(duty cycles):0.01%
VBR @TJ= VBR@25°C x (1+αT x
(TJ - 25))
(αT:Temperature Coefficient)
• Glass passivated chip
junction
High temperature
soldering guaranteed:
260°C/40 seconds at
terminals
UL Recognized compound
meeting flammability
rating V-0
Meet MSL level1, per
J-STD-020, LF maximun
peak of 260°C
Matte tin lead–free plated
• Halogen free and RoHS
compliant
2nd level interconnect is
Pb-free per IPC/JEDEC
J-STD-609A.01
Applications
SMBJ-HR components are ideal for the protection of I/O
Interfaces, VCC bus and other vulnerable circuits used in
Telecom, Computer, Industrial and Consumer electronic
Maximum Ratings and Thermal Characteristics
(TA=25OC unless otherwise noted)
Parameter Symbol Value Unit
Peak Pulse Power Dissipation at
TA=25ºC by 10/1000µs Waveform
(Fig.2)(Note 1), (Note 2)
PPPM 600 W
Power Dissipation on Infinite Heat
Sink at TL=50OCPM(AV) 5.0 W
Peak Forward Surge Current, 8.3ms
Single Half Sine Wave (Note 3) IFSM 100 A
Maximum Instantaneous Forward
Voltage at 50A for Unidirectional
Only
VF3.5V V
Operating Junction and Storage
Temperature Range TJ, TSTG -65 to 150 °C
Typical Thermal Resistance Junction
to Lead RuJL 20 °C/W
Typical Thermal Resistance Junction
to Ambient RuJA 10 0 °C/W
Notes:
1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25OC per Fig. 3.
2. Mounted on copper pad area of 0.2x0.2” (5.0 x 5.0mm) to each terminal.
3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional
component only, duty cycle=4 per minute maximum.
AGENCY AGENCY FILE NUMBER
E128662/E230531
SMBJ-HR Series
Bi-directional
Uni-directional
Functional Diagram
Bi-directional
Uni-directional
Cathode Anode
1
RoHS
e3
Pb
Transient Voltage Suppression Diodes
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 03/28/18
Surface Mount – 600W > SMBJ-HR Series
Electrical Characteristics (TA=25°C unless otherwise noted)
Part
Number
(Uni)
Part
Number
(Bi)
Marking Reverse
Stand off
Voltage VR
(Volts)
Breakdown
Voltage VBR
(Volts) @ IT
Test
Current
IT
(mA)
Maximum
Clamping
Voltage VC
@ Ipp
(V)
Maximum
Peak
Pulse
Current Ipp
(A)
Maximum
Reverse
Leakage IR
@ VR
(µA)
Agency
Approval
UNI BI MIN MAX
SMBJ5.0A-HR SMBJ5.0CA-HR KE AE 5.0 6.40 7. 0 0 10 9.2 65.3 800 X
SMBJ6.0A-HR SMBJ6.0CA-HR KG AG 6.0 6.67 7.37 10 10.3 58.3 800 X
SMBJ6.5A-HR SMBJ6.5CA-HR KK AK 6.5 7.22 7.98 10 11. 2 53.6 500 X
SMBJ7.0A-HR SMBJ7.0CA-HR KM AM 7. 0 7.78 8.60 10 12.0 50.0 200 X
SMBJ7.5A-HR SMBJ7.5CA-HR KP AP 7. 5 8.33 9.21 1 12.9 46.6 100 X
SMBJ8.0A-HR SMBJ8.0CA-HR KR AR 8.0 8.89 9.83 1 13.6 44.2 50 X
SMBJ8.5A-HR SMBJ8.5CA-HR KT AT 8.5 9.44 10.40 1 14.4 41.7 20 X
SMBJ9.0A-HR SMBJ9.0CA-HR KV AV 9.0 10.00 11. 10 1 15.4 39.0 10 X
SMBJ10A-HR SMBJ10CA-HR KX AX 10.0 11. 10 12.30 1 1 7. 0 35.3 5 X
SMBJ11A-HR SMBJ11CA-HR KZ AZ 11. 0 12.20 13.50 1 18.2 33.0 1 X
SMBJ12A-HR SMBJ12CA-HR LE BE 12.0 13.30 14.70 1 19.9 30.2 1 X
SMBJ13A-HR SMBJ13CA-HR LG BG 13.0 14.40 15.90 1 21.5 28.0 1 X
SMBJ14A-HR SMBJ14CA-HR LK BK 14.0 15.60 17.20 1 23.2 25.9 1 X
SMBJ15A-HR SMBJ15CA-HR LM BM 15.0 16.70 18.50 1 24.4 24.6 1 X
SMBJ16A-HR SMBJ16CA-HR LP BP 16.0 17.80 19.70 1 26.0 23.1 1 X
SMBJ17A-HR SMBJ17CA-HR LR BR 1 7. 0 18.90 20.90 1 27.6 21.8 1 X
SMBJ18A-HR SMBJ18CA-HR LT BT 18.0 20.00 22.10 1 29.2 20.6 1 X
SMBJ20A-HR SMBJ20CA-HR LV BV 20.0 22.20 24.50 1 32.4 18.6 1 X
SMBJ22A-HR SMBJ22CA-HR LX BX 22.0 24.40 26.90 1 35.5 16.9 1 X
SMBJ24A-HR SMBJ24CA-HR LZ BZ 24.0 26.70 29.50 1 38.9 15.5 1 X
SMBJ26A-HR SMBJ26CA-HR ME CE 26.0 28.90 31.90 1 42.1 14.3 1 X
SMBJ28A-HR SMBJ28CA-HR MG CG 28.0 31.10 34.40 1 45.4 13.3 1 X
SMBJ30A-HR SMBJ30CA-HR MK CK 30.0 33.30 36.80 1 48.4 12.4 1 X
SMBJ33A-HR SMBJ33CA-HR MM CM 33.0 36.70 40.60 1 53.3 11. 3 1 X
SMBJ36A-HR SMBJ36CA-HR MP CP 36.0 40.00 44.20 1 58.1 10.4 1 X
SMBJ40A-HR SMBJ40CA-HR MR CR 40.0 44.40 49.10 1 64.5 9.3 1 X
SMBJ43A-HR SMBJ43CA-HR MT CT 43.0 47.80 52.80 1 69.4 8.7 1 X
SMBJ45A-HR SMBJ45CA-HR MV CV 45.0 50.00 55.30 1 72.7 8.3 1 X
SMBJ48A-HR SMBJ48CA-HR MX CX 48.0 53.30 58.90 1 77.4 7. 8 1 X
SMBJ51A-HR SMBJ51CA-HR MZ CZ 51.0 56.70 62.70 1 82.4 7. 3 1 X
SMBJ54A-HR SMBJ54CA-HR NE DE 54.0 60.00 66.30 1 87.1 6.9 1 X
SMBJ58A-HR SMBJ58CA-HR NG DG 58.0 64.40 71.20 1 93.6 6.5 1 X
SMBJ60A-HR SMBJ60CA-HR NK DK 60.0 66.70 73.70 1 96.8 6.2 1 X
SMBJ64A-HR SMBJ64CA-HR NM DM 64.0 71.10 78.60 1 103.0 5.9 1 X
SMBJ70A-HR SMBJ70CA-HR NP DP 70.0 77.80 86.00 1 113.0 5.3 1 X
SMBJ75A-HR SMBJ75CA-HR NR DR 75.0 83.30 92.10 1 121.0 5.0 1 X
SMBJ78A-HR SMBJ78CA-HR NT DT 78.0 86.70 95.80 1 126.0 4.8 1 X
SMBJ85A-HR SMBJ85CA-HR NV DV 85.0 94.40 104.00 1 137.0 4.4 1 X
- SMBJ90CA-HR - DX 90.0 100.00 111. 0 0 1 146.0 4.1 1 X
- SMBJ100CA-HR - DZ 100.0 111.0 0 123.00 1 162.0 3.7 1 X
- SMBJ110CA-HR - EE 110.0 122.00 135.00 1 177.0 3.4 1 X
- SMBJ120CA-HR - EG 120.0 133.00 147.00 1 193.0 3.1 1 X
- SMBJ130CA-HR - EK 130.0 144.00 159.00 1 209.0 2.9 1 X
- SMBJ150CA-HR - EM 150.0 167.00 185.00 1 243.0 2.5 1 X
- SMBJ160CA-HR - EP 160.0 178.00 197.00 1 259.0 2.3 1 X
- SMBJ170CA-HR - ER 170.0 189.00 209.00 1 275.0 2.2 1 X
Note:
1. For bidirectional type having VR of 10 volts and less, the IR limit is double.
2. 100% High Temperature Storage Life test and Reflow Simulation.
3. 100% HTRB(High Temperature Reverse Bias). For Unidirectional, 150OC/100%VR/96hours,
for Bidirectional, 150OC/100%VR/192hrs(96hours for each direction for Bidirectional).
4. IR measured at room temperature +25OC
5. Each lot of parts will pass group B test requirement.
2
Transient Voltage Suppression Diodes
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 03/28/18
Surface Mount – 600W > SMBJ-HR Series
I-V Curve Characteristics
Vc VBR VR
IR
IT
Ipp
V
Uni-directional
VF
Vc VBR VR
IR
IT
Ipp
V
Vc
VBR
VR
Ipp
IR
IT
Bi-directional
PPPM Peak Pulse Power Dissipation (IPP x VC) -- Max power dissipation
VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation
VBR Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (IT)
VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current)
IR Reverse Leakage Current -- Current measured at VR
VF Forward Voltage Drop for Uni-directional
Group B Test Requirement
Screen Method Condition Requirement
Surge test 10/1000 µs Peak Pluse Waveform Maximum clamping Voltage (VC) @
Peak Plus Current (IPP)
Sample Size 45 perform 10x
Accept 0 failures
Burn - In (HTRB) MIL -STD-750, Method 1038.5 Applied voltage
100% VR@150°C
Sample size 45
340 hours (680 hours for bi-direction
products, each direction 340 hours)
Accept 0 failures
Electrical test -- IR@VR, V(BR)@IT
Sample size 45
Accept 0 failures
3
100% Vision Inspection MIL-STD-750 method 2074
100% High Temperature Storage Life (168hrs,150°C) MIL-STD-750 method 1031
100% X-RAY inspection MIL-STD-750 method 2076
100% Temperature Cycle Test (-55 to150°C, 20 cycles, dwell time 15 min) MIL-STD-750 method 1051
100% Reflow (2x) JEDEC J-STD-020
100% Surge Test (2x) MIL-STD-750 method 4066
100% HTRB 150°C Bias=VR(80% breakdown voltage, 96hrs, and each direction
at 96 hrs for Bi-directional products) MIL–STD–750 method 1038
Final Electrical Test( 100% 3 sigma limit, 100% dynamic test and PAT limit) MIL-STD-750 method 4016.4021.4011
Screen Process
Note: Up-screen program can be specified by customers request by contacting Littelfuse customer service
Transient Voltage Suppression Diodes
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 03/28/18
Surface Mount – 600W > SMBJ-HR Series
Ratings and Characteristic Curves (TA=25°C unless otherwise noted)
0.1
1
10
100
0.0000010.00001 0.0001 0.001
td-Pulse Width (sec.)
0.2x0.2" (5.0x5.0mm)
Copper Pad Area
PPPM-Peak Pulse Power (kW)
Figure 2 - Peak Pulse Power Rating
Voltage Transients
Time
Voltage Across TVS
Current Through TVS
Voltage or Current
Figure 1 - TVS Transients Clamping Waveform
IPPM- Peak Pulse Current, % IRSM
0
0
50
100
150
1.0 2.0 3.0 4.0
tr=10µsec
Peak Value
IPPM
IPPM
2
TJ=25°C
Pulse Width(td) is defined
as the point where the peak
current decays to 50% of IPPM
10/1000µsec. Waveform
as defined by R.E.A
td
t-Time (ms)
Half Value
IPPM ( )
0
20
40
60
80
100
0255075100 125150 17
5
T
A-Ambient temperature (ºC)
Peak Pulse Power (P
PP
) or Current (I
PP
)
Derating in Percentage
%
1
10
100
1000
10000
1.010.0100.0 1000.0
Cj (pF)
Tj
=25C
f=
1.0MHz
Vs
ig=50mVp-p
Uni-directional V=0V
VBR - Reverse Breakdown Voltage (V)
Uni-directional @VR
Bi-directional @VR
0
1
2
3
4
5
6
0255075100 125 150 175
PM(AV)
, Steady State Power Dissipatio
n
(W)
TA - Ambient Te mperature (ºC)
Figure 3 - Pulse Derating Curve Figure 4 - Pulse Waveform
Figure 5 - Typical Junction Capacitance
Figure 6 - Steady State Power Dissipation Derating Curve
4
TL-Lead Temperature (˚C)
(Power Dissipation on Infinite H eat Sink )
Transient Voltage Suppression Diodes
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 03/28/18
Surface Mount – 600W > SMBJ-HR Series
Physical Specifications
Weight 0.003 ounce, 0.093 grams
Case JEDEC DO214AA. Molded plastic body
over glass passivated junction
Polarity Color band denotes cathode except
Bidirectional
Terminal Matte Tin-plated leads, Solderable per
JESD22-B102
Soldering Parameters
Temperature (T)
Time (t)
Ts(min)
Ts(max)
TL
TP
ts
Preheat
tL
tp
Ramp-up Critical Zone
TL to TP
Ramp-down
t 25˚C to Peak
25˚C
Reflow Condition Lead–free assembly
Pre Heat
- Temperature Min (Ts(min)) 150°C
- Temperature Max (Ts(max)) 200°C
- Time (min to max) (ts) 60 – 180 secs
Average ramp up rate (Liquidus Temp (TL)
to peak 3°C/second max
TS(max) to TL - Ramp-up Rate 3°C/second max
Reflow - Temperature (TL) (Liquidus) 217°C
- Time (min to max) (ts) 60 – 150 seconds
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)20 – 40 seconds
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 280°C
Environmental Specifications
High Temp. Storage JESD22-A103
HTRB JESD22-A108
Temperature Cycling JESD22-A104
MSL JEDEC-J-STD-020, Level 1
H3TRB JESD22-A101
RSH JESD22-B106
5
0
20
40
60
80
100
120
110100
Nu
mber of Cycles at 60 Hz
IFSM
- Peak Forward Surge Current (A)
Figure 7 - Maximum Non-Repetitive Peak Forward
Surge Current Uni-Directional Only
Transient Voltage Suppression Diodes
© 2018 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 03/28/18
Surface Mount – 600W > SMBJ-HR Series
Dimensions
Dimensions
Inches Millimeters
Min Max Min Max
A 0.077 0.086 1.950 2.200
B 0.160 0.180 4.060 4.570
C 0.130 0.155 3.300 3.940
D 0.084 0.096 2.130 2.440
E 0.030 0.060 0.760 1.520
F - 0.008 - 0.203
G 0.205 0.220 5.210 5.590
H 0.006 0.012 0.152 0.305
I 0.089 - 2.260 -
J 0.085 - 2.160 -
K - 0.107 - 2.740
L 0.085 - 2.160 -
(all dimensions in mm)
I
L
K
J
Solder Pads
A
D
EG
F
H
C
B
Cathode Band
(for Uni-directional products only)
DO-214AA (SMB J-Bend)
Part Numbering System
VOLTAGE
BI-DIRECTIONAL
5% VOLTAGE TOLERANCE
SERIES
SMBJ -HR XXX CA
High Reliability
Packaging
Part number Component Package Quantity Packaging Option Packaging Specification
SMBJxxxXX-HR DO-214AA 3000 Tape & Reel - 12mm tape/13” reel EIA STD RS-481
Part Marking System
Tape and Reel Specification
0.47
(12.0)
0.315
(8.0)
0.157
(4.0)
0.49
(12.5)
0.80 (20.2)
Arbor Hole Dia.
13.0 (330)
Dimensions are in inches
(and millimeters).
Direction of Feed
0.059 DIA
(1.5) Cover tape
Cathode
F
XX
YMXXX
Marking Code
Trace Code Marking
Y:Year Code
M: Month Code
XXX: Lot Code
Littelfuse Logo
Cathode Band
(for uni-directional products only)
6
(for unidirectional
version only)
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Littelfuse:
SMBJ33CA-HR SMBJ10A-HR SMBJ14CA-HR SMBJ75A-HR SMBJ20CA-HR SMBJ15CA-HR SMBJ8.0CA-HR
SMBJ70CA-HR SMBJ16CA-HR SMBJ48CA-HR SMBJ7.5CA-HR SMBJ15A-HR SMBJ160CA-HR SMBJ8.0A-HR
SMBJ78CA-HR SMBJ43A-HR SMBJ36A-HR SMBJ11CA-HR SMBJ78A-HR SMBJ13A-HR SMBJ130CA-HR
SMBJ48A-HR SMBJ60CA-HR SMBJ7.0A-HR SMBJ9.0CA-HR SMBJ110CA-HR SMBJ12CA-HR SMBJ6.0CA-HR
SMBJ150CA-HR SMBJ45CA-HR SMBJ51CA-HR SMBJ6.5CA-HR SMBJ90CA-HR SMBJ8.5CA-HR SMBJ26A-HR
SMBJ6.5A-HR SMBJ85CA-HR SMBJ100CA-HR SMBJ18CA-HR SMBJ7.5A-HR SMBJ10CA-HR SMBJ40A-HR
SMBJ22CA-HR SMBJ70A-HR SMBJ85A-HR SMBJ51A-HR SMBJ28A-HR SMBJ170CA-HR SMBJ13CA-HR
SMBJ24A-HR SMBJ17CA-HR SMBJ58CA-HR SMBJ33A-HR SMBJ24CA-HR SMBJ58A-HR SMBJ26CA-HR
SMBJ36CA-HR SMBJ45A-HR SMBJ11A-HR SMBJ12A-HR SMBJ30A-HR SMBJ9.0A-HR SMBJ43CA-HR
SMBJ7.0CA-HR SMBJ120CA-HR SMBJ28CA-HR SMBJ64CA-HR SMBJ6.0A-HR SMBJ54A-HR SMBJ14A-HR
SMBJ16A-HR SMBJ18A-HR SMBJ54CA-HR SMBJ40CA-HR SMBJ30CA-HR SMBJ22A-HR SMBJ5.0CA-HR
SMBJ60A-HR SMBJ8.5A-HR SMBJ5.0A-HR SMBJ20A-HR SMBJ75CA-HR SMBJ64A-HR SMBJ17A-HR