www.ti.com SLLS266G - FEBRUARY 1997 - REVISED JULY AUGUST 2008 FEATURES D Design to Protect Submicron 3-V or 5-V Circuits from Noise Transients D Port ESD Protection Capability Exceeds: DESCRIPTION The SN65220 is a single transient voltage suppressor and the SN65240 and SN75240 are dual transient voltage suppressors designed to provide electrical noise transient protection to Universal Serial Bus (USB) full-speed ports. Note that the input capacitance of the device makes it unsuitable for high-speed USB 2.0 applications. Ports SN65220DBV (TOP VIEW) NC 1 GND 2 NC 3 6 A 5 GND A A1 A2 GND 4 B B B1 B2 GND SN65240P, SN65240PW SN75240P, SN75240PW (TOP VIEW) GND C GND D 1 2 3 4 8 7 6 5 A GND B GND CURRENT vs VOLTAGE 7.5 5 2.5 Current - A EQUIVALENT SCHEMATIC DIAGRAM A or C SN65220YZB (Size: 925 mm x 925 mm +6 mm) (TOP VIEW) NC - No internal connection When read horizontally, Pin 1 is the bottom left pin. Any cabled I/O can be subjected to electrical noise transients from various sources. These noise transients can cause damage to the USB transceiver and/or the USB ASIC if they are of sufficient magnitude and duration. USB ports are typically implemented in 3-V or 5-V digital CMOS with very limited ESD protection. The SN65220, SN65240, and SN75240 can significantly increase the port ESD protection level and reduce the risk of damage to the circuits of the USB port. The IEC1000-4-2 ESD performance of the SN65220, SN65240, and SN75240 is measured at the system level. Therefore, system design impacts the results of these tests. A high compliance level may be attained with proper board design and layout. APPLICATIONS D USB Full-Speed Host, Hub, or Peripheral SADI D D D D - 15-kV Human Body Model - 2-kV Machine Model Available in a WCSP Chip-Scale Package Stand-Off Voltage . . . 6 V Min Low Current Leakage . . . 1 A Max at 6 V Low Capacitance . . . 35 pF Typical 0 -2.5 -5 -7.5 GND -10 -10 -5 0 5 10 15 Voltage - V B or D (One Suppressor Shown) NOTE: All GND terminals should be connected to ground. NOTE A: Typical current versus voltage curve was derived using the IEC 1.2/50-s surge waveform. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. !" # $%&" !# '%()$!" *!"&+ *%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*& "&#"0 !)) '!!&"&#+ Copyright E 1997 - 2008, Texas Instruments Incorporated www.ti.com SLLS266G - FEBRUARY 1997 - REVISED JULY AUGUST 2008 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. IEC1000-4-2 COMPLIANCE LEVEL MAXIMUM TEST VOLTAGE IEC1000-4-2 COMPLIANCE LEVEL CONTACT DISCHARGE (kV) AIR DISCHARGE (kV) 1 2 2 2 4 4 3 6 8 4 8 15 PACKAGE/ORDERING INFORMATION PRODUCT SUPRESSORS SN65220 SN65240 SN75240 1 2 2 TA PACKAGE PACKAGE DESIGNATOR MARKED AS WCSP-4 YZB NWP or 65220 SOT23-6 DBV SADI DIP-8 P TSSOP-8 PW DIP-8 P -40C to 85C -40C -40 C to 85 85C C 0C 0 C to 70 70C C TSSOP-8 PW ORDER NUMBER SN65220YZBR (Reel) SN65220YZBT (Mini Reel) SN65220DBVR (Reel) SN65220DBVT (Mini Reel) SN65240P (Rail) A65240 SN65240PW (Rail) SN65240PWR (Reel) SN75240P (Rail) A75240 SN75240PW (Rail) SN75240PWR (Reel) ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted(1) UNIT Continuous power dissipation Electrostatic discharge See Dissipation Rating Table 15 kV(2), 2 kV(3) Peak power dissipation, PD(peak) 60 W Peak forward surge current, IFSM 3A Peak reverse surge current, IRSM -9 A Storage temperature range, Tstg -65C to 150C (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. (2) Human Body Model - Tested in accordance with JEDEC Standard 22, Test Method A114-A. (3) Charged Device Model - Tested in accordance with JEDEC Standard 22, Test Method C101. 2 www.ti.com SLLS266G - FEBRUARY 1997 - REVISED JULY AUGUST 2008 DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DBV P TA = 70C POWER RATING TA = 85C POWER RATING 385 mW DERATING FACTOR ABOVE TA = 25C 3.1 mW/C 246 mW 200 mW 1150 mW 9.2 mW/C 736 mW 598 mW PW 520 mW 4.2 mW/C 331 mW 268 mW This is the inverse of the junction-to-ambient thermal resistance when board-mounted and with no air flow. recommended operating conditions SN75240 Operating free-air temperature, TA SN65220, SN65240 MIN MAX 0 70 -40 85 UNIT C electrical characteristics over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS Ilkg V(BR) Leakage current Breakdown voltage VI = 6 V at A, B, C, or D terminals VI = 1 mA at A, B, C, or D terminals CIN Input capacitance to ground VI = 0.4 sin (4E6t) + 0.5 V MIN TYP 6.5 7 35 MAX UNIT 1 A 8 V pF APPLICATION INFORMATION Full-Speed or Low-Speed USB Host-or-Hub Port Transceiver Full-Speed or Low-Speed USB Down Stream Transceiver 1.5 kW (Full Speed Only) 27 W D+ A A 15 kW 15 kW 27 W GND SN75220 or 1/2 SNx5240 B 27 W D+ D- SN75220 or 1/2 SNx5240 D- B GND 1.5 kW (Low Speed Only) 27 W 3 PACKAGE OPTION ADDENDUM www.ti.com 5-Mar-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty SN65220DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65220DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65220DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65220DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65220YZBR ACTIVE DSBGA YZB 4 3000 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM SN65220YZBT ACTIVE DSBGA YZB 4 250 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM SN65240P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN65240PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN65240PW ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65240PWG4 ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65240PWR ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN65240PWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75240P ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75240PE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type SN75240PW ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75240PWG4 ACTIVE TSSOP PW 8 150 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75240PWLE OBSOLETE TSSOP PW 8 TBD Call TI SN75240PWR ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN75240PWRG4 ACTIVE TSSOP PW 8 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 5-Mar-2010 Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF SN65220 : * Automotive: SN65220-Q1 NOTE: Qualified Version Definitions: * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) SN65220DBVR SOT-23 DBV 6 3000 180.0 9.0 3.15 SN65220DBVT SOT-23 DBV 6 250 180.0 9.0 3.15 SN65220YZBR DSBGA YZB 4 3000 178.0 8.4 1.06 SN65220YZBT DSBGA YZB 4 250 178.0 8.4 1.06 SN65240PWR TSSOP PW 8 2000 330.0 12.4 SN75240PWR TSSOP PW 8 2000 330.0 12.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.2 1.4 4.0 8.0 Q3 3.2 1.4 4.0 8.0 Q3 1.06 0.81 4.0 8.0 Q1 1.06 0.81 4.0 8.0 Q1 7.0 3.6 1.6 8.0 12.0 Q1 7.0 3.6 1.6 8.0 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN65220DBVR SOT-23 DBV 6 3000 182.0 182.0 20.0 SN65220DBVT SOT-23 DBV 6 250 182.0 182.0 20.0 SN65220YZBR DSBGA YZB 4 3000 217.0 193.0 35.0 SN65220YZBT DSBGA YZB 4 250 217.0 193.0 35.0 SN65240PWR TSSOP PW 8 2000 367.0 367.0 35.0 SN75240PWR TSSOP PW 8 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated