Numonyx(R) ForteTM Serial Flash Memory M25P16 16 Mbit, serial Flash memory, 75 MHz SPI bus interface Features 16 Mbit of Flash memory Page Program (up to 256 bytes) in 0.64 ms (typical) VFDFPN8 (MP) 6 x 5 mm (MLP8) Sector Erase (512 Kbit) in 0.6 s (typical) VDFPN8 (ME) 8 x 6 mm (MLP8) Bulk Erase (16 Mbit) in 13 s (typical) 2.7 V to 3.6 V single supply voltage SPI bus compatible serial interface 75 MHz Clock rate (maximum) SO8N (MN) 150 mils width Deep Power-down mode 1 A (typical) Electronic signatures - JEDEC standard two-byte signature (2015h) - Unique ID code (UID) with 16 bytes readonly, available upon customer request - RES instruction, one-byte, signature (14h), for backward compatibility PDIP8 (BA) 300 mils width More than 100,000 Erase/Program cycles per sector SO8W (MW) 208 mils width SO16 (MF) 300 mils width Hardware Write Protection: protected area size defined by three non-volatile bits (BP0, BP1 and BP2) More than 20 year data retention UFDFPN8 (MC) (MLP8 4 x 3 mm) Packages - RoHS compliant Automotive Certified Parts Available April 2010 Rev 20 1/59 www.numonyx.com 1 Contents M25P16 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 Serial Data output (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 Serial Data input (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.3 Serial Clock (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.4 Chip Select (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5 Hold (HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.6 Write Protect (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.7 VCC supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.8 VSS ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 SPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4 Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.1 Page programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.2 Sector Erase and Bulk Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.3 Polling during a Write, Program or Erase cycle . . . . . . . . . . . . . . . . . . . . 12 4.4 Active Power, Standby Power and Deep Power-down modes . . . . . . . . . 12 4.5 Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.6 Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.7 Hold condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5 Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 2/59 6.1 Write Enable (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.2 Write Disable (WRDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 6.3 Read Identification (RDID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.4 Read Status Register (RDSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.4.1 WIP bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.4.2 WEL bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 6.4.3 BP2, BP1, BP0 bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 M25P16 Contents 6.4.4 SRWD bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.5 Write Status Register (WRSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 6.6 Read Data Bytes (READ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 6.7 Read Data Bytes at Higher Speed (FAST_READ) . . . . . . . . . . . . . . . . . . 26 6.8 Page Program (PP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 6.9 Sector Erase (SE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 6.10 Bulk Erase (BE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6.11 Deep Power-down (DP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 6.12 Release from Deep Power-down and Read Electronic Signature (RES) . 32 7 Power-up and power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 8 Initial delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 10 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 11 Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 12 Ordering Information, Standard Parts . . . . . . . . . . . . . . . . . . . . . . . . . . 53 13 Ordering Information, Automotive Parts . . . . . . . . . . . . . . . . . . . . . . . . 55 14 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 3/59 List of tables M25P16 List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. 4/59 Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Protected area sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Memory organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Instruction set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Read Identification (RDID) data-out sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Status Register format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Power-up timing and VWI threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Data retention and endurance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 DC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 AC characteristics (110 nm technology) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 AC characteristics (25 MHz operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead, 6 x 5 mm, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 x 6 mm, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 SO8N - 8 lead plastic small outline, 150 mils body width, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 SO8 wide - 8 lead plastic small outline, 208 mils body width, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 SO16 wide - 16-lead plastic small outline, 300 mils body width, mechanical data . . . . . . 49 PDIP8 - 8 lead Plastic Small Outline, 300 mils body width, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 UFDFPN (MLP8) 8-lead ultra thin fine pitch dual flat package no lead, 4X3 mm package mechanical data52 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 M25P16 List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SO8, VFQFPN, VDFPN, and PDIP8 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SO16 connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bus master and memory devices on the SPI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 SPI modes supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Hold condition activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Write Enable (WREN) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Write Disable (WRDI) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Read Identification (RDID) instruction sequence and data-out sequence . . . . . . . . . . . . . 20 Read Status Register (RDSR) instruction sequence and data-out sequence . . . . . . . . . . 22 Write Status Register (WRSR) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Read Data Bytes (READ) instruction sequence and data-out sequence . . . . . . . . . . . . . . 25 Read Data Bytes at Higher Speed (FAST_READ) instruction sequence and data-out sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 15. Page Program (PP) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 16. Sector Erase (SE) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Figure 17. Bulk Erase (BE) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Figure 18. Deep Power-down (DP) instruction sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Figure 19. Release from Deep Power-down and Read Electronic Signature (RES) instruction sequence and data-out sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Figure 20. Release from Deep Power-down (RES) instruction sequence . . . . . . . . . . . . . . . . . . . . . . 33 Figure 21. Power-up timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Figure 22. AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Figure 23. Serial input timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Figure 24. Write Protect setup and hold timing during WRSR when SRWD = 1 . . . . . . . . . . . . . . . . . 42 Figure 25. Hold timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Figure 26. Output timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Figure 27. VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead, 6 x 5 mm, package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure 28. VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 x 6 mm, package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Figure 29. SO8N - 8 lead plastic small outline, 150 mils body width, package outline . . . . . . . . . . . . 47 Figure 30. SO8W - 8 lead plastic small outline, 208 mils body width, package outline. . . . . . . . . . . . 48 Figure 31. SO16 wide - 16-lead plastic small outline, 300 mils body width, package outline . . . . . . . 49 Figure 32. PDIP8 - 8 lead Plastic Small Outline, 300 mils body width, package outline . . . . . . . . . . . 50 Figure 33. UFDFPN (MLP8) 8-lead ultra thin fine pitch dual flat package no lead, 4X3 mm package mechanical data51 5/59 Description 1 M25P16 Description The M25P16 is a 16 Mbit (2 Mbit x 8) serial Flash memory, with advanced write protection mechanisms, accessed by a high speed SPI-compatible bus. The memory can be programmed 1 to 256 bytes at a time, using the Page Program instruction. The memory is organized as 32 sectors, each containing 256 pages. Each page is 256 bytes wide. Thus, the whole memory can be viewed as consisting of 8192 pages, or 2 097 152 bytes. The whole memory can be erased using the Bulk Erase instruction, or a sector at a time, using the Sector Erase instruction. Figure 1. Logic diagram VCC D Q C S M25P16 W HOLD VSS AI05762 Table 1. Signal names Signal name 6/59 Function Direction C Serial Clock Input D Serial Data input Input Q Serial Data output Output S Chip Select Input W Write Protect Input HOLD Hold Input VCC Supply voltage VSS Ground M25P16 Description Figure 2. SO8, VFQFPN, VDFPN, and PDIP8 connections M25P16 S Q W VSS 1 2 3 4 8 7 6 5 VCC HOLD C D AI08517 1. There is an exposed central pad on the underside of the VFQFPN package. This is pulled, internally, to VSS, and must not be allowed to be connected to any other voltage or signal line on the PCB. 2. See Package mechanical section for package dimensions, and how to identify pin-1. Figure 3. SO16 connections M25P16 HOLD VCC DU DU DU DU S Q 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 C D DU DU DU DU VSS W AI08594B 1. DU = Don't use 2. See Package mechanical section for package dimensions, and how to identify pin-1. 7/59 Signal description 2 Signal description 2.1 Serial Data output (Q) M25P16 This output signal is used to transfer data serially out of the device. Data is shifted out on the falling edge of Serial Clock (C). 2.2 Serial Data input (D) This input signal is used to transfer data serially into the device. It receives instructions, addresses, and the data to be programmed. Values are latched on the rising edge of Serial Clock (C). 2.3 Serial Clock (C) This input signal provides the timing of the serial interface. Instructions, addresses, or data present at Serial Data input (D) are latched on the rising edge of Serial Clock (C). Data on Serial Data output (Q) changes after the falling edge of Serial Clock (C). 2.4 Chip Select (S) When this input signal is High, the device is deselected and Serial Data output (Q) is at high impedance. Unless an internal Program, Erase or Write Status Register cycle is in progress, the device will be in the Standby mode (this is not the Deep Power-down mode). Driving Chip Select (S) Low selects the device, placing it in the Active Power mode. After power-up, a falling edge on Chip Select (S) is required prior to the start of any instruction. 2.5 Hold (HOLD) The Hold (HOLD) signal is used to pause any serial communications with the device without deselecting the device. During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data input (D) and Serial Clock (C) are Don't care. To start the Hold condition, the device must be selected, with Chip Select (S) driven Low. 2.6 Write Protect (W) The main purpose of this input signal is to freeze the size of the area of memory that is protected against program or erase instructions (as specified by the values in the BP2, BP1 and BP0 bits of the Status Register). 8/59 M25P16 2.7 Signal description VCC supply voltage VCC is the supply voltage. 2.8 VSS ground VSS is the reference for the VCC supply voltage. 9/59 SPI modes 3 M25P16 SPI modes These devices can be driven by a microcontroller with its SPI peripheral running in either of the two following modes: CPOL=0, CPHA=0 CPOL=1, CPHA=1 For these two modes, input data is latched in on the rising edge of Serial Clock (C), and output data is available from the falling edge of Serial Clock (C). The difference between the two modes, as shown in Figure 5, is the clock polarity when the bus master is in Standby mode and not transferring data: C remains at 0 for (CPOL=0, CPHA=0) C remains at 1 for (CPOL=1, CPHA=1) Figure 4. Bus master and memory devices on the SPI bus VSS VCC R SDO SPI interface with (CPOL, CPHA) = (0, 0) or (1, 1) SDI SCK VCC C Q D SPI Bus Master SPI memory device R CS3 VCC C Q D VSS C Q D VCC VSS SPI memory device R VSS SPI memory device R CS2 CS1 S W HOLD S W HOLD S W HOLD AI12836b 1. The Write Protect (W) and Hold (HOLD) signals should be driven, High or Low as appropriate. Figure 4 shows an example of three devices connected to an MCU, on an SPI bus. Only one device is selected at a time, so only one device drives the Serial Data output (Q) line at a time, the other devices are high impedance. Resistors R (represented in Figure 4) ensure that the M25P16 is not selected if the Bus Master leaves the S line in the high impedance state. As the Bus Master may enter a state where all inputs/outputs are in high impedance at the same time (for example, when the Bus Master is reset), the clock line (C) must be connected to an external pull-down resistor so that, when all inputs/outputs become high impedance, the S line is pulled High while the C line is pulled Low (thus ensuring that S and C do not become High at the same time, and so, that the tSHCH requirement is met). The typical value of R is 100 k , assuming that the time constant R*Cp (Cp = parasitic capacitance of the bus line) is shorter than the time during which the Bus Master leaves the SPI bus in high impedance. 10/59 M25P16 SPI modes Example: Cp = 50 pF, that is R*Cp = 5 s: the application must ensure that the Bus Master never leaves the SPI bus in the high impedance state for a time period shorter than 5 s. Figure 5. SPI modes supported CPOL CPHA 0 0 C 1 1 C D Q MSB MSB AI01438B 11/59 Operating features 4 Operating features 4.1 Page programming M25P16 To program one data byte, two instructions are required: Write Enable (WREN), which is one byte, and a Page Program (PP) sequence, which consists of four bytes plus data. This is followed by the internal Program cycle (of duration tPP). To spread this overhead, the Page Program (PP) instruction allows up to 256 bytes to be programmed at a time (changing bits from 1 to 0), provided that they lie in consecutive addresses on the same page of memory. For optimized timings, it is recommended to use the Page Program (PP) instruction to program all consecutive targeted bytes in a single sequence versus using several Page Program (PP) sequences with each containing only a few bytes (see Page Program (PP)). 4.2 Sector Erase and Bulk Erase The Page Program (PP) instruction allows bits to be reset from 1 to 0. Before this can be applied, the bytes of memory need to have been erased to all 1s (FFh). This can be achieved either a sector at a time, using the Sector Erase (SE) instruction, or throughout the entire memory, using the Bulk Erase (BE) instruction. This starts an internal Erase cycle (of duration tSE or tBE). The Erase instruction must be preceded by a Write Enable (WREN) instruction. 4.3 Polling during a Write, Program or Erase cycle A further improvement in the time to Write Status Register (WRSR), Program (PP) or Erase (SE or BE) can be achieved by not waiting for the worst case delay (tW, tPP, tSE, or tBE). The Write In Progress (WIP) bit is provided in the Status Register so that the application program can monitor its value, polling it to establish when the previous Write cycle, Program cycle or Erase cycle is complete. 4.4 Active Power, Standby Power and Deep Power-down modes When Chip Select (S) is Low, the device is selected, and in the Active Power mode. When Chip Select (S) is High, the device is deselected, but could remain in the Active Power mode until all internal cycles have completed (Program, Erase, Write Status Register). The device then goes in to the Standby Power mode. The device consumption drops to ICC1. The Deep Power-down mode is entered when the specific instruction (the Deep Powerdown (DP) instruction) is executed. The device consumption drops further to ICC2. The device remains in this mode until another specific instruction (the Release from Deep Power-down and Read Electronic Signature (RES) instruction) is executed. While in the Deep Power-down mode, the device ignores all Write, Program and Erase instructions (see Deep Power-down (DP)). This can be used as an extra software protection mechanism, when the device is not in active use, to protect the device from inadvertent Write, Program or Erase instructions. 12/59 M25P16 4.5 Operating features Status Register The Status Register contains a number of status and control bits that can be read or set (as appropriate) by specific instructions. See Section 6.4: Read Status Register (RDSR) for a detailed description of the Status Register bits. 4.6 Protection modes The environments where non-volatile memory devices are used can be very noisy. No SPI device can operate correctly in the presence of excessive noise. To help combat this, the M25P16 features the following data protection mechanisms: Power on reset and an internal timer (tPUW) can provide protection against inadvertent changes while the power supply is outside the operating specification Program, Erase and Write Status Register instructions are checked that they consist of a number of clock pulses that is a multiple of eight, before they are accepted for execution All instructions that modify data must be preceded by a Write Enable (WREN) instruction to set the Write Enable Latch (WEL) bit. This bit is returned to its reset state by the following events: - Power-up - Write Disable (WRDI) instruction completion - Write Status Register (WRSR) instruction completion - Page Program (PP) instruction completion - Sector Erase (SE) instruction completion - Bulk Erase (BE) instruction completion Software Protected Mode (SPM): The Block Protect bits (BP2, BP1, BP0) allow part of the memory to be configured as read-only. Hardware Protected Mode (HPM): The Write Protect (W) signal allows the Block Protect bits (BP2, BP1, BP0) and the Status Register Write Disable bit (SRWD) to be protected. In addition to the low power consumption feature, the Deep Power-down mode offers extra software protection, as all Write, Program and Erase instructions are ignored. 13/59 Operating features M25P16 Table 2. Protected area sizes Status Register content Memory content BP2 BP1 BP0 bit bit bit Protected area Unprotected area 0 0 0 none All sectors(1) (32 sectors: 0 to 31) 0 0 1 Upper 32nd (Sector 31) Lower 31/32nds (31 sectors: 0 to 30) 0 1 0 Upper sixteenth (2 sectors: 30 and 31) Lower 15/16ths (30 sectors: 0 to 29) 0 1 1 Upper eighth (4 sectors: 28 to 31) Lower seven-eighths (28 sectors: 0 to 27) 1 0 0 Upper quarter (8 sectors: 24 to 31) Lower three-quarters (24 sectors: 0 to 23) 1 0 1 Upper half (16 sectors: 16 to 31) Lower half (16 sectors: 0 to 15) 1 1 0 All sectors (32 sectors: 0 to 31) none 1 1 1 All sectors (32 sectors: 0 to 31) none 1. The device is ready to accept a Bulk Erase instruction only if all Block Protect bits (BP2, BP1, BP0) are 0. 4.7 Hold condition The Hold (HOLD) signal is used to pause any serial communications with the device without resetting the clocking sequence. However, taking this signal Low does not terminate any Write Status Register, Program or Erase cycle that is currently in progress. To enter the Hold condition, the device must be selected, with Chip Select (S) Low. The Hold condition starts on the falling edge of the Hold (HOLD) signal, provided that this coincides with Serial Clock (C) being Low (as shown in Figure 6). The Hold condition ends on the rising edge of the Hold (HOLD) signal, provided that this coincides with Serial Clock (C) being Low. If the falling edge does not coincide with Serial Clock (C) being Low, the Hold condition starts after Serial Clock (C) next goes Low. Similarly, if the rising edge does not coincide with Serial Clock (C) being Low, the Hold condition ends after Serial Clock (C) next goes Low (this is shown in Figure 6: Hold condition activation). During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data input (D) and Serial Clock (C) are Don't care. Normally, the device is kept selected, with Chip Select (S) driven Low, for the whole duration of the Hold condition. This is to ensure that the state of the internal logic remains unchanged from the moment of entering the Hold condition. If Chip Select (S) goes High while the device is in the Hold condition, this has the effect of resetting the internal logic of the device. To restart communication with the device, it is necessary to drive Hold (HOLD) High, and then to drive Chip Select (S) Low. This prevents the device from going back to the Hold condition. 14/59 M25P16 Operating features Figure 6. Hold condition activation C HOLD Hold condition (standard use) Hold condition (non-standard use) AI02029D 15/59 Memory organization 5 M25P16 Memory organization The memory is organized as: 2 097 152 bytes (8 bits each) 32 sectors (512 Kbits, 65536 bytes each) 8192 pages (256 bytes each). Each page can be individually programmed (bits are programmed from 1 to 0). The device is sector or bulk erasable (bits are erased from 0 to 1) but not page erasable. Figure 7. Block diagram HOLD W High voltage Generator Control Logic S C D I/O Shift Register Q Address Register and Counter Status Register 256 byte Data Buffer 1FFFFFh Y Decoder Size of the read-only memory area 00000h 000FFh 256 bytes (page size) X Decoder AI04987 16/59 M25P16 Memory organization Table 3. Memory organization Sector Address range 31 1F0000h 1FFFFFh 30 1E0000h 1EFFFFh 29 1D0000h 1DFFFFh 28 1C0000h 1CFFFFh 27 1B0000h 1BFFFFh 26 1A0000h 1AFFFFh 25 190000h 19FFFFh 24 180000h 18FFFFh 23 170000h 17FFFFh 22 160000h 16FFFFh 21 150000h 15FFFFh 20 140000h 14FFFFh 19 130000h 13FFFFh 18 120000h 12FFFFh 17 110000h 11FFFFh 16 100000h 10FFFFh 15 0F0000h 0FFFFFh 14 0E0000h 0EFFFFh 13 0D0000h 0DFFFFh 12 0C0000h 0CFFFFh 11 0B0000h 0BFFFFh 10 0A0000h 0AFFFFh 9 090000h 09FFFFh 8 080000h 08FFFFh 7 070000h 07FFFFh 6 060000h 06FFFFh 5 050000h 05FFFFh 4 040000h 04FFFFh 3 030000h 03FFFFh 2 020000h 02FFFFh 1 010000h 01FFFFh 0 000000h 00FFFFh 17/59 Instructions 6 M25P16 Instructions All instructions, addresses and data are shifted in and out of the device, most significant bit first. Serial Data input (D) is sampled on the first rising edge of Serial Clock (C) after Chip Select (S) is driven Low. Then, the one-byte instruction code must be shifted in to the device, most significant bit first, on Serial Data input (D), each bit being latched on the rising edges of Serial Clock (C). The instruction set is listed in Table 4: Instruction set. Every instruction sequence starts with a one-byte instruction code. Depending on the instruction, this might be followed by address bytes, or by data bytes, or by both or none. In the case of a Read Data Bytes (READ), Read Data Bytes at Higher Speed (FAST_READ), Read Status Register (RDSR), Read Identification (RDID) or Release from Deep Power-down, and Read Electronic Signature (RES) instruction, the shifted-in instruction sequence is followed by a data-out sequence. Chip Select (S) can be driven High after any bit of the data-out sequence is being shifted out. For a Page Program (PP), Sector Erase (SE), Bulk Erase (BE), Write Status Register (WRSR), Write Enable (WREN), Write Disable (WRDI), or Deep Power-down (DP) instruction, Chip Select (S) must be driven High exactly at a byte boundary. Otherwise the instruction is rejected and not executed. That is, Chip Select (S) must driven High when the number of clock pulses after Chip Select (S) being driven Low is an exact multiple of eight. All attempts to access the memory array during a Write Status Register cycle, Program cycle or Erase cycle are ignored, and the internal Write Status Register cycle, Program cycle or Erase cycle continues unaffected. Note: Output Hi-Z is defined as the point where data out is no longer driven. Table 4. Instruction set Instruction Description One-byte instruction code Address bytes Dummy bytes Data bytes WREN Write Enable 0000 0110 06h 0 0 0 WRDI Write Disable 0000 0100 04h 0 0 0 RDID Read Identification 1001 1111 9Fh 0 0 1 to 20 RDSR Read Status Register 0000 0101 05h 0 0 1 to WRSR Write Status Register 0000 0001 01h 0 0 1 READ Read Data Bytes 0000 0011 03h 3 0 1 to Read Data Bytes at Higher Speed 0000 1011 0Bh 3 1 1 to PP Page Program 0000 0010 02h 3 0 1 to 256 SE Sector Erase 1101 1000 D8h 3 0 0 BE Bulk Erase 1100 0111 C7h 0 0 0 DP Deep Power-down 1011 1001 B9h 0 0 0 Release from Deep Power-down, and Read Electronic Signature 0 3 1 to 1010 1011 ABh 0 0 0 FAST_READ RES Release from Deep Power-down 18/59 M25P16 6.1 Instructions Write Enable (WREN) The Write Enable (WREN) instruction (Figure 8) sets the Write Enable Latch (WEL) bit. The Write Enable Latch (WEL) bit must be set prior to every Page Program (PP), Sector Erase (SE), Bulk Erase (BE) and Write Status Register (WRSR) instruction. The Write Enable (WREN) instruction is entered by driving Chip Select (S) Low, sending the instruction code, and then driving Chip Select (S) High. Figure 8. Write Enable (WREN) instruction sequence S 0 1 2 3 4 5 6 7 C Instruction D High Impedance Q AI02281E 6.2 Write Disable (WRDI) The Write Disable (WRDI) instruction (Figure 9) resets the Write Enable Latch (WEL) bit. The Write Disable (WRDI) instruction is entered by driving Chip Select (S) Low, sending the instruction code, and then driving Chip Select (S) High. The Write Enable Latch (WEL) bit is reset under the following conditions: Power-up Write Disable (WRDI) instruction completion Write Status Register (WRSR) instruction completion Page Program (PP) instruction completion Sector Erase (SE) instruction completion Bulk Erase (BE) instruction completion Figure 9. Write Disable (WRDI) instruction sequence S 0 1 2 3 4 5 6 7 C Instruction D High Impedance Q AI03750D 19/59 Instructions 6.3 M25P16 Read Identification (RDID) The Read Identification (RDID) instruction allows to read the device identification data: Manufacturer identification (1 byte) Device identification (2 bytes) A Unique ID code (UID) (17 bytes, of which 16 available upon customer request). The manufacturer identification is assigned by JEDEC, and has the value 20h for Numonyx. The device identification is assigned by the device manufacturer, and indicates the memory type in the first byte (20h), and the memory capacity of the device in the second byte (15h). The UID contains the length of the following data in the first byte (set to 10h), and 16 bytes of the optional Customized Factory Data (CFD) content. The CFD bytes are read-only and can be programmed with customers data upon their request. If the customers do not make requests, the devices are shipped with all the CFD bytes programmed to zero (00h). Note: See Section 12: Ordering Information, Standard Parts on page 53 for CFD programmed devices. Any Read Identification (RDID) instruction while an Erase or Program cycle is in progress, is not decoded, and has no effect on the cycle that is in progress. The device is first selected by driving Chip Select (S) Low. Then, the 8-bit instruction code for the instruction is shifted in. After this, the 24-bit device identification, stored in the memory, the 8-bit CFD length followed by 16 bytes of CFD content will be shifted out on Serial Data output (Q). Each bit is shifted out during the falling edge of Serial Clock (C). The instruction sequence is shown in Figure 10: Read Identification (RDID) instruction sequence and data-out sequence. The Read Identification (RDID) instruction is terminated by driving Chip Select (S) High at any time during data output. When Chip Select (S) is driven High, the device is put in the Standby Power mode. Once in the Standby Power mode, the device waits to be selected, so that it can receive, decode and execute instructions. Table 5. Read Identification (RDID) data-out sequence Device identification Manufacturer identification UID Memory type Memory capacity CFD length CFD content 20h 15h 10h 16 bytes 20h Figure 10. Read Identification (RDID) instruction sequence and data-out sequence S 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 28 29 30 31 C Instruction D Manufacturer identification UID Device identification High Impedance Q 15 14 13 MSB MSB 3 2 1 0 MSB AI06809c 20/59 M25P16 6.4 Instructions Read Status Register (RDSR) The Read Status Register (RDSR) instruction allows the Status Register to be read. The Status Register may be read at any time, even while a Program, Erase or Write Status Register cycle is in progress. When one of these cycles is in progress, it is recommended to check the Write In Progress (WIP) bit before sending a new instruction to the device. It is also possible to read the Status Register continuously, as shown in Figure 11. Table 6. Status Register format b7 SRWD b0 0 0 BP2 BP1 BP0 WEL WIP Status Register Write Protect Block Protect bits Write Enable Latch bit Write In Progress bit The status and control bits of the Status Register are as follows: 6.4.1 WIP bit The Write In Progress (WIP) bit indicates whether the memory is busy with a Write Status Register, Program or Erase cycle. When set to `1', such a cycle is in progress, when reset to `0' no such cycle is in progress. 6.4.2 WEL bit The Write Enable Latch (WEL) bit indicates the status of the internal Write Enable Latch. When set to `1' the internal Write Enable Latch is set, when set to `0' the internal Write Enable Latch is reset and no Write Status Register, Program or Erase instruction is accepted. 6.4.3 BP2, BP1, BP0 bits The Block Protect (BP2, BP1, BP0) bits are non-volatile. They define the size of the area to be software protected against Program and Erase instructions. These bits are written with the Write Status Register (WRSR) instruction. When one or more of the Block Protect (BP2, BP1, BP0) bits is set to `1', the relevant memory area (as defined in Table 2) becomes protected against Page Program (PP) and Sector Erase (SE) instructions. The Block Protect (BP2, BP1, BP0) bits can be written provided that the Hardware Protected mode has not been set. The Bulk Erase (BE) instruction is executed if, and only if, all Block Protect (BP2, BP1, BP0) bits are 0. 21/59 Instructions 6.4.4 M25P16 SRWD bit The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect (W) signal allow the device to be put in the Hardware Protected mode (when the Status Register Write Disable (SRWD) bit is set to `1', and Write Protect (W) is driven Low). In this mode, the non-volatile bits of the Status Register (SRWD, BP2, BP1, BP0) become read-only bits and the Write Status Register (WRSR) instruction is no longer accepted for execution. Figure 11. Read Status Register (RDSR) instruction sequence and data-out sequence S 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 C Instruction D Status Register Out Status Register Out High Impedance Q 7 MSB 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 MSB AI02031E 22/59 M25P16 6.5 Instructions Write Status Register (WRSR) The Write Status Register (WRSR) instruction allows new values to be written to the Status Register. Before it can be accepted, a Write Enable (WREN) instruction must previously have been executed. After the Write Enable (WREN) instruction has been decoded and executed, the device sets the Write Enable Latch (WEL). The Write Status Register (WRSR) instruction is entered by driving Chip Select (S) Low, followed by the instruction code and the data byte on Serial Data input (D). The instruction sequence is shown in Figure 12. The Write Status Register (WRSR) instruction has no effect on b6, b5, b1 and b0 of the Status Register. b6 and b5 are always read as 0. Chip Select (S) must be driven High after the eighth bit of the data byte has been latched in. If not, the Write Status Register (WRSR) instruction is not executed. As soon as Chip Select (S) is driven High, the self-timed Write Status Register cycle (whose duration is tW) is initiated. While the Write Status Register cycle is in progress, the Status Register may still be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Write Status Register cycle, and is 0 when it is completed. When the cycle is completed, the Write Enable Latch (WEL) is reset. The Write Status Register (WRSR) instruction allows the user to change the values of the Block Protect (BP2, BP1, BP0) bits, to define the size of the area that is to be treated as read-only, as defined in Table 2. The Write Status Register (WRSR) instruction also allows the user to set or reset the Status Register Write Disable (SRWD) bit in accordance with the Write Protect (W) signal. The Status Register Write Disable (SRWD) bit and Write Protect (W) signal allow the device to be put in the Hardware Protected mode (HPM). The Write Status Register (WRSR) instruction is not executed once the Hardware Protected mode (HPM) is entered. Figure 12. Write Status Register (WRSR) instruction sequence S 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 C Instruction Status Register In 7 D High Impedance 6 5 4 3 2 1 0 MSB Q AI02282D 23/59 Instructions M25P16 Table 7. Protection modes W SRWD signal bit 1 0 1 1 0 Write Protection of the Status Register Software Protected mode (SPM) Status Register is writable (if the WREN instruction has set the WEL bit) The values in the SRWD, BP2, BP1 and BP0 bits can be changed Protected against Page Program, Sector Erase and Bulk Erase Ready to accept Page Program and Sector Erase instructions Hardwar e Protected mode (HPM) Status Register is Hardware write protected The values in the SRWD, BP2, BP1 and BP0 bits cannot be changed Protected against Page Program, Sector Erase and Bulk Erase Ready to accept Page Program and Sector Erase instructions 0 0 1 Memory content Mode Protected area(1) Unprotected area(1) 1. As defined by the values in the Block Protect (BP2, BP1, BP0) bits of the Status Register, as shown in Table 6. The protection features of the device are summarized in Table 7. When the Status Register Write Disable (SRWD) bit of the Status Register is 0 (its initial delivery state), it is possible to write to the Status Register provided that the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction, regardless of the whether Write Protect (W) is driven High or Low. When the Status Register Write Disable (SRWD) bit of the Status Register is set to `1', two cases need to be considered, depending on the state of Write Protect (W): If Write Protect (W) is driven High, it is possible to write to the Status Register provided that the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction If Write Protect (W) is driven Low, it is not possible to write to the Status Register even if the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction (attempts to write to the Status Register are rejected, and are not accepted for execution). As a consequence, all the data bytes in the memory area that are software protected (SPM) by the Block Protect (BP2, BP1, BP0) bits of the Status Register, are also hardware protected against data modification. Regardless of the order of the two events, the Hardware Protected mode (HPM) can be entered: by setting the Status Register Write Disable (SRWD) bit after driving Write Protect (W) Low or by driving Write Protect (W) Low after setting the Status Register Write Disable (SRWD) bit. The only way to exit the Hardware Protected mode (HPM) once entered is to pull Write Protect (W) High. If Write Protect (W) is permanently tied High, the Hardware Protected mode (HPM) can never be activated, and only the Software Protected mode (SPM), using the Block Protect (BP2, BP1, BP0) bits of the Status Register, can be used. 24/59 M25P16 6.6 Instructions Read Data Bytes (READ) The device is first selected by driving Chip Select (S) Low. The instruction code for the Read Data Bytes (READ) instruction is followed by a 3-byte address (A23-A0), each bit being latched-in during the rising edge of Serial Clock (C). Then the memory contents, at that address, is shifted out on Serial Data output (Q), each bit being shifted out, at a maximum frequency fR, during the falling edge of Serial Clock (C). The instruction sequence is shown in Figure 13. The first byte addressed can be at any location. The address is automatically incremented to the next higher address after each byte of data is shifted out. The whole memory can, therefore, be read with a single Read Data Bytes (READ) instruction. When the highest address is reached, the address counter rolls over to 000000h, allowing the read sequence to be continued indefinitely. The Read Data Bytes (READ) instruction is terminated by driving Chip Select (S) High. Chip Select (S) can be driven High at any time during data output. Any Read Data Bytes (READ) instruction, while an Erase, Program or Write cycle is in progress, is rejected without having any effects on the cycle that is in progress. Figure 13. Read Data Bytes (READ) instruction sequence and data-out sequence S 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 C Instruction 24-bit address 23 22 21 D 3 2 1 0 MSB Data Out 1 High Impedance Q 7 6 5 4 3 2 Data Out 2 1 0 7 MSB AI03748D 1. Address bits A23 to A21 are Don't care. 25/59 Instructions 6.7 M25P16 Read Data Bytes at Higher Speed (FAST_READ) The device is first selected by driving Chip Select (S) Low. The instruction code for the Read Data Bytes at Higher Speed (FAST_READ) instruction is followed by a 3-byte address (A23A0) and a dummy byte, each bit being latched-in during the rising edge of Serial Clock (C). Then the memory contents, at that address, is shifted out on Serial Data output (Q), each bit being shifted out, at a maximum frequency fC, during the falling edge of Serial Clock (C). The instruction sequence is shown in Figure 14. The first byte addressed can be at any location. The address is automatically incremented to the next higher address after each byte of data is shifted out. The whole memory can, therefore, be read with a single Read Data Bytes at Higher Speed (FAST_READ) instruction. When the highest address is reached, the address counter rolls over to 000000h, allowing the read sequence to be continued indefinitely. The Read Data Bytes at Higher Speed (FAST_READ) instruction is terminated by driving Chip Select (S) High. Chip Select (S) can be driven High at any time during data output. Any Read Data Bytes at Higher Speed (FAST_READ) instruction, while an Erase, Program or Write cycle is in progress, is rejected without having any effects on the cycle that is in progress. Figure 14. Read Data Bytes at Higher Speed (FAST_READ) instruction sequence and data-out sequence S 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 C Instruction 24-bit address 23 22 21 D 3 2 1 0 High Impedance Q S 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 C Dummy byte D 7 6 5 4 3 2 1 0 DATA OUT 2 DATA OUT 1 7 Q MSB 6 5 4 3 2 1 0 7 MSB 6 5 4 3 2 1 0 7 MSB AI04006 1. Address bits A23 to A21 are Don't care. 26/59 M25P16 6.8 Instructions Page Program (PP) The Page Program (PP) instruction allows bytes to be programmed in the memory (changing bits from 1 to 0). Before it can be accepted, a Write Enable (WREN) instruction must previously have been executed. After the Write Enable (WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL). The Page Program (PP) instruction is entered by driving Chip Select (S) Low, followed by the instruction code, three address bytes and at least one data byte on Serial Data input (D). If the 8 least significant address bits (A7-A0) are not all zero, all transmitted data that goes beyond the end of the current page are programmed from the start address of the same page (from the address whose 8 least significant bits (A7-A0) are all zero). Chip Select (S) must be driven Low for the entire duration of the sequence. The instruction sequence is shown in Figure 15. If more than 256 bytes are sent to the device, previously latched data are discarded and the last 256 data bytes are guaranteed to be programmed correctly within the same page. If less than 256 data bytes are sent to device, they are correctly programmed at the requested addresses without having any effects on the other bytes of the same page. For optimized timings, it is recommended to use the Page Program (PP) instruction to program all consecutive targeted bytes in a single sequence versus using several Page Program (PP) sequences with each containing only a few bytes. Chip Select (S) must be driven High after the eighth bit of the last data byte has been latched in, otherwise the Page Program (PP) instruction is not executed. As soon as Chip Select (S) is driven High, the self-timed Page Program cycle (whose duration is tPP) is initiated. While the Page Program cycle is in progress, the Status Register may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Page Program cycle, and is 0 when it is completed. At some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is reset. A Page Program (PP) instruction applied to a page which is protected by the Block Protect (BP2, BP1, BP0) bits (see Table 2 and Table 3) is not executed. 27/59 Instructions M25P16 Figure 15. Page Program (PP) instruction sequence S 0 1 2 3 4 5 6 7 8 28 29 30 31 32 33 34 35 36 37 38 39 9 10 C Instruction 24-bit address 23 22 21 D 3 2 Data byte 1 1 0 7 6 5 4 3 2 1 0 MSB MSB 2078 2079 2077 2076 2075 2074 2073 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 2072 S 1 0 C Data byte 2 D 7 6 MSB 5 4 3 2 Data byte 3 1 0 7 MSB 6 5 4 3 2 Data byte 256 1 0 7 6 5 4 3 2 MSB AI04082B 1. Address bits A23 to A21 are Don't care. 28/59 M25P16 6.9 Instructions Sector Erase (SE) The Sector Erase (SE) instruction sets to `1' (FFh) all bits inside the chosen sector. Before it can be accepted, a Write Enable (WREN) instruction must previously have been executed. After the Write Enable (WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL). The Sector Erase (SE) instruction is entered by driving Chip Select (S) Low, followed by the instruction code, and three address bytes on Serial Data input (D). Any address inside the sector (see Table 3) is a valid address for the Sector Erase (SE) instruction. Chip Select (S) must be driven Low for the entire duration of the sequence. The instruction sequence is shown in Figure 16. Chip Select (S) must be driven High after the eighth bit of the last address byte has been latched in, otherwise the Sector Erase (SE) instruction is not executed. As soon as Chip Select (S) is driven High, the self-timed Sector Erase cycle (whose duration is tSE) is initiated. While the Sector Erase cycle is in progress, the Status Register may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Sector Erase cycle, and is 0 when it is completed. At some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is reset. A Sector Erase (SE) instruction applied to a page which is protected by the Block Protect (BP2, BP1, BP0) bits (see Table 2 and Table 3) is not executed. Figure 16. Sector Erase (SE) instruction sequence S 0 1 2 3 4 5 6 7 8 9 29 30 31 C Instruction D 24 Bit Address 23 22 2 1 0 MSB AI03751D 1. Address bits A23 to A21 are Don't care. 29/59 Instructions 6.10 M25P16 Bulk Erase (BE) The Bulk Erase (BE) instruction sets all bits to `1' (FFh). Before it can be accepted, a Write Enable (WREN) instruction must previously have been executed. After the Write Enable (WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL). The Bulk Erase (BE) instruction is entered by driving Chip Select (S) Low, followed by the instruction code on Serial Data input (D). Chip Select (S) must be driven Low for the entire duration of the sequence. The instruction sequence is shown in Figure 17. Chip Select (S) must be driven High after the eighth bit of the instruction code has been latched in, otherwise the Bulk Erase instruction is not executed. As soon as Chip Select (S) is driven High, the self-timed Bulk Erase cycle (whose duration is tBE) is initiated. While the Bulk Erase cycle is in progress, the Status Register may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Bulk Erase cycle, and is 0 when it is completed. At some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is reset. The Bulk Erase (BE) instruction is executed only if all Block Protect (BP2, BP1, BP0) bits are 0. The Bulk Erase (BE) instruction is ignored if one, or more, sectors are protected. Figure 17. Bulk Erase (BE) instruction sequence S 0 1 2 3 4 5 6 7 C Instruction D AI03752D 30/59 M25P16 6.11 Instructions Deep Power-down (DP) Executing the Deep Power-down (DP) instruction is the only way to put the device in the lowest consumption mode (the Deep Power-down mode). It can also be used as a software protection mechanism, while the device is not in active use, as in this mode, the device ignores all Write, Program and Erase instructions. Driving Chip Select (S) High deselects the device, and puts the device in the Standby mode (if there is no internal cycle currently in progress). But this mode is not the Deep Powerdown mode. The Deep Power-down mode can only be entered by executing the Deep Power-down (DP) instruction, subsequently reducing the standby current (from ICC1 to ICC2, as specified in Table 14). To take the device out of Deep Power-down mode, the Release from Deep Power-down and Read Electronic Signature (RES) instruction must be issued. No other instruction must be issued while the device is in Deep Power-down mode. The Release from Deep Power-down and Read Electronic Signature (RES) instruction also allows the electronic signature of the device to be output on Serial Data output (Q). The Deep Power-down mode automatically stops at power-down, and the device always powers up in the Standby mode. The Deep Power-down (DP) instruction is entered by driving Chip Select (S) Low, followed by the instruction code on Serial Data input (D). Chip Select (S) must be driven Low for the entire duration of the sequence. The instruction sequence is shown in Figure 18. Chip Select (S) must be driven High after the eighth bit of the instruction code has been latched in, otherwise the Deep Power-down (DP) instruction is not executed. As soon as Chip Select (S) is driven High, it requires a delay of tDP before the supply current is reduced to ICC2 and the Deep Power-down mode is entered. Any Deep Power-down (DP) instruction, while an Erase, Program or Write cycle is in progress, is rejected without having any effects on the cycle that is in progress. Figure 18. Deep Power-down (DP) instruction sequence S 0 1 2 3 4 5 6 7 tDP C Instruction D Standby mode Deep Power-down mode AI03753D 31/59 Instructions 6.12 M25P16 Release from Deep Power-down and Read Electronic Signature (RES) To take the device out of Deep Power-down mode, the Release from Deep Power-down and Read Electronic Signature (RES) instruction must be issued. No other instruction must be issued while the device is in Deep Power-down mode. The instruction can also be used to read, on Serial Data output (Q), the old-style 8-bit electronic signature, whose value for the M25P16 is 14h. Please note that this is not the same as, or even a subset of, the JEDEC 16-bit electronic signature that is read by the Read Identifier (RDID) instruction. The old-style electronic signature is supported for reasons of backward compatibility, only, and should not be used for new designs. New designs should, instead, make use of the JEDEC 16-bit electronic signature, and the Read Identifier (RDID) instruction. Except while an Erase, Program or Write Status Register cycle is in progress, the Release from Deep Power-down and Read Electronic Signature (RES) instruction always provides access to the old-style 8-bit electronic signature of the device, and can be applied even if the Deep Power-down mode has not been entered. Any Release from Deep Power-down and Read Electronic Signature (RES) instruction while an Erase, Program or Write Status Register cycle is in progress, is not decoded, and has no effect on the cycle that is in progress. The device is first selected by driving Chip Select (S) Low. The instruction code is followed by 3 dummy bytes, each bit being latched-in on Serial Data input (D) during the rising edge of Serial Clock (C). Then, the old-style 8-bit electronic signature, stored in the memory, is shifted out on Serial Data output (Q), each bit being shifted out during the falling edge of Serial Clock (C). The instruction sequence is shown in Figure 19. The Release from Deep Power-down and Read Electronic Signature (RES) instruction is terminated by driving Chip Select (S) High after the electronic signature has been read at least once. Sending additional clock cycles on Serial Clock (C), while Chip Select (S) is driven Low, cause the electronic signature to be output repeatedly. When Chip Select (S) is driven High, the device is put in the Standby Power mode. If the device was not previously in the Deep Power-down mode, the transition to the Standby Power mode is immediate. If the device was previously in the Deep Power-down mode, though, the transition to the Standby Power mode is delayed by tRES2, and Chip Select (S) must remain High for at least tRES2(max). Once in the Standby Power mode, the device waits to be selected, so that it can receive, decode and execute instructions. 32/59 M25P16 Instructions Figure 19. Release from Deep Power-down and Read Electronic Signature (RES) instruction sequence and data-out sequence S 0 1 2 3 4 5 6 7 8 28 29 30 31 32 33 34 35 36 37 38 9 10 C Instruction tRES2 3 Dummy bytes 23 22 21 D 3 2 1 0 MSB Electronic Signature Out High Impedance 7 Q 6 5 4 3 2 1 0 MSB Deep Power-down mode Standby mode AI04047C 1. The value of the 8-bit electronic signature, for the M25P16, is 14h. Figure 20. Release from Deep Power-down (RES) instruction sequence S 0 1 2 3 4 5 6 7 tRES1 C Instruction D High Impedance Q Deep Power-down mode Standby mode AI04078B Driving Chip Select (S) High after the 8-bit instruction byte has been received by the device, but before the whole of the 8-bit electronic signature has been transmitted for the first time (as shown in Figure 20), still ensures that the device is put into Standby Power mode. If the device was not previously in the Deep Power-down mode, the transition to the Standby Power mode is immediate. If the device was previously in the Deep Power-down mode, though, the transition to the Standby Power mode is delayed by tRES1, and Chip Select (S) must remain High for at least tRES1(max). Once in the Standby Power mode, the device waits to be selected, so that it can receive, decode and execute instructions. 33/59 Power-up and power-down 7 M25P16 Power-up and power-down At power-up and power-down, the device must not be selected (that is Chip Select (S) must follow the voltage applied on VCC) until VCC reaches the correct value: VCC(min) at power-up, and then for a further delay of tVSL VSS at power-down A safe configuration is provided in Section 3: SPI modes. To avoid data corruption and inadvertent write operations during power-up, a Power-On Reset (POR) circuit is included. The logic inside the device is held reset while VCC is less than the Power-On Reset (POR) threshold voltage, VWI - all operations are disabled, and the device does not respond to any instruction. Moreover, the device ignores all Write Enable (WREN), Page Program (PP), Sector Erase (SE), Bulk Erase (BE) and Write Status Register (WRSR) instructions until a time delay of tPUW has elapsed after the moment that VCC rises above the VWI threshold. However, the correct operation of the device is not guaranteed if, by this time, VCC is still below VCC(min). No Write Status Register, Program or Erase instructions should be sent until the later occurance of: tPUW after VCC passed the VWI threshold tVSL after VCC passed the VCC(min) level. These values are specified in Table 8. If the delay, tVSL, has elapsed, after VCC has risen above VCC(min), the device can be selected for READ instructions even if the tPUW delay is not yet fully elapsed. At power-up, the device is in the following state: The device is in the Standby mode (not the Deep Power-down mode) The Write Enable Latch (WEL) bit is reset The Write In Progress (WIP) bit is reset. Normal precautions must be taken for supply rail decoupling, to stabilize the VCC supply. Each device in a system should have the VCC rail decoupled by a suitable capacitor close to the package pins. Generally, this capacitor is of the order of 100 nF. At power-down, when VCC drops from the operating voltage to below the Power-On Reset (POR) threshold voltage, VWI, all operations are disabled and the device does not respond to any instruction. The designer needs to be aware that if a power-down occurs while a Write, Program or Erase cycle is in progress, some data corruption can result. 34/59 M25P16 Initial delivery state Figure 21. Power-up timing VCC VCC(max) Program, Erase and Write commands are rejected by the device Chip selection not allowed VCC(min) tVSL Reset state of the device Read access allowed Device fully accessible VWI tPUW time AI04009C Table 8. Power-up timing and VWI threshold Symbol tVSL(1) tPUW (1) VWI(1) Parameter Min Max Unit VCC(min) to S Low 30 -- s Time delay to Write instruction 1 10 ms 1.0 2.1 V Write Inhibit voltage 1. These parameters are characterized only. 8 Initial delivery state The device is delivered with the memory array erased: all bits are set to `1' (each byte contains FFh). The Status Register contains 00h (all Status Register bits are 0). 35/59 Maximum rating 9 M25P16 Maximum rating Stressing the device above the rating listed in Table 9: Absolute maximum ratings may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Refer also to the Numonyx SURE Program and other relevant quality documents. Table 9. Absolute maximum ratings Symbol TSTG TLEAD Parameter Storage temperature Lead temperature during soldering Input and output voltage (with respect to ground) VCC Supply voltage Electrostatic discharge voltage (Human Body Max Unit -65 150 C -- VIO VESD Min model)(4) see (1) -0.6(2) VCC + 0.6(3) 4.0 V -2000 2000 V 2. The minimum voltage may reach the value of -2 V for no more than 20 ns during transitions. 3. The maximum voltage may reach the value of VCC+2 V for no more than 20 ns during transitions. 36/59 V -0.6 1. Compliant with JEDEC Std J-STD-020C (for small body, Sn-Pb or Pb assembly), the Numonyx RoHS compliant 7191395 specification, and the European directive on Restrictions on Hazardous Substances (RoHS) 2002/95/EU. 4. JEDEC Std JESD22-A114A (C1 = 100 pF, R1 = 1500 , R2 = 500 ). C M25P16 10 DC and AC parameters DC and AC parameters This section summarizes the operating and measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristic tables that follow are derived from tests performed under the measurement conditions summarized in the relevant tables. Designers should check that the operating conditions in their circuit match the measurement conditions when relying on the quoted parameters. Table 10. Operating conditions Symbol Parameter VCC Max Unit 2.7 3.6 V grade 3 -40 125 C grade 6 -40 85 C Supply voltage TA Table 11. Min Ambient operating temperature Data retention and endurance Parameter Condition Min Max Unit Program/Erase Cycles Grade 3, Autograde 6, Grade 6 100000 -- Cycles per Sector Data Retention at 55C 20 -- years Min Max Table 12. AC measurement conditions Symbol Parameter Load capacitance 30 Input rise and fall times CL Unit pF 5 ns Input pulse voltages 0.2VCC to 0.8VCC V Input timing reference voltages 0.3VCC to 0.7VCC V VCC / 2 V Output timing reference voltages Figure 22. AC measurement I/O waveform Input levels Input and output timing reference levels 0.8VCC 0.7VCC 0.5VCC 0.3VCC 0.2VCC AI07455 Table 13. Symbol COUT CIN Capacitance(1) Parameter Output capacitance (Q) Input capacitance (other pins) Test Condition Min Max Unit VOUT = 0 V -- 8 pF VIN = 0 V -- 6 pF 1. Sampled only, not 100% tested, at TA = 25 C and a frequency of 20 MHz. 37/59 DC and AC parameters Table 14. Symbol M25P16 DC characteristics Test condition (in addition to those in Table 10) Parameter Max Unit ILI Input leakage current -- -- 2 A ILO Output leakage current -- -- 2 A -- 50 A ICC1 Standby current -- 100 A Deep Power-down current -- 10 A ICC2 -- 100 A C = 0.1VCC / 0.9.VCC at 75 MHz, Q = open -- 8 mA C = 0.1VCC / 0.9.VCC at 33 MHz, Q = open -- 4 mA Grade 6 ICC3 38/59 Min Grade 3 S = VCC, VIN = VSS or VCC Grade 6 Grade 3 S = VCC, VIN = VSS or VCC Operating current (READ) ICC4 Operating current (PP) S = VCC -- 15 mA ICC5 Operating current (WRSR) S = VCC -- 15 mA ICC6 Operating current (SE) S = VCC -- 15 mA ICC7 Operating current (BE) S = VCC -- 15 mA VIL Input low voltage -- - 0.5 0.3VCC V VIH Input high voltage -- 0.7VCC VCC+0.4 V VOL Output low voltage IOL = 1.6 mA -- 0.4 V VOH Output high voltage IOH = -100 A VCC-0.2 -- V M25P16 DC and AC parameters Table 15. AC characteristics (110 nm technology) Applies only to products made with 110 nm technology Test conditions specified in Table 10 and Table 12 Symbol Alt. fC fC fR Parameter Typ(1) Min Max Unit Clock frequency for the following instructions: FAST_READ, PP, SE, BE, DP, RES, WREN, WRDI, RDID, RDSR, WRSR DC -- 75 MHz Clock frequency for READ instructions DC -- 33 MHz tCH(2) tCLH Clock High time 6 -- -- ns tCL(1) tCLL Clock Low time 6 -- -- ns 0.1 -- -- V/ns 0.1 -- -- V/ns Clock Rise time(4) (peak to peak) tCLCH(3) tCHCL (3) tSLCH Clock Fall time (4) (peak to peak) tCSS S Active Setup time (relative to C) tCHSL S Not Active Hold time (relative to C) 5 -- -- ns 5 -- -- ns tDVCH tDSU Data In Setup time 2 -- -- ns tCHDX tDH Data In Hold time 5 -- -- ns tCHSH S Active Hold time (relative to C) 5 -- -- ns tSHCH S Not Active Setup time (relative to C) 5 -- -- ns 100 -- -- ns tSHSL tSHQZ(3) tCLQV tCLQX tCSH S Deselect time tDIS Output Disable time tV Clock Low to Output Valid under 30 pF/10 pF -- -- 8 ns -- -- 8/6 ns tHO Output Hold time 0 -- -- ns tHLCH HOLD Setup time (relative to C) 5 -- -- ns tCHHH HOLD Hold time (relative to C) 5 -- -- ns tHHCH HOLD Setup time (relative to C) 5 -- -- ns tCHHL HOLD Hold time (relative to C) 5 -- -- ns tHHQX(3) tLZ HOLD to Output Low-Z -- 8 ns (3) tHZ HOLD to Output High-Z -- 8 ns tHLQZ tWHSL(5) tSHWL (5) tDP(3) Write Protect Setup time 20 -- -- ns Write Protect Hold time 100 -- -- ns S High to Deep Power-down mode -- -- 3 s tRES1(3) S High to Standby mode without Read Electronic Signature -- -- 30 s tRES2(3) S High to Standby mode with Read Electronic -- Signature -- 30 s 15 ms tW Write Status Register cycle time -- 1.3 39/59 DC and AC parameters Table 15. M25P16 AC characteristics (110 nm technology) (continued) Applies only to products made with 110 nm technology Test conditions specified in Table 10 and Table 12 Symbol Alt. Parameter Page Program cycle time (256 bytes) tPP (6) Typ(1) Min -- 0.64 Page Program cycle time (n bytes, where n = 1 -- to 4) 0.01 Page Program cycle time (n bytes, where n = 5 -- to 256) int(n/8) x 0.02(7) Max Unit 5 ms tSE Sector Erase cycle time -- 0.6 3 s tBE Bulk Erase cycle time -- 13 40 s 1. Typical values given for TA = 25 C. 2. tCH + tCL must be greater than or equal to 1/ fC. 3. Value guaranteed by characterization, not 100% tested in production. 4. Expressed as a slew-rate. 5. Only applicable as a constraint for a WRSR instruction when SRWD is set at `1'. 6. When using the Page Program (PP) instruction to program consecutive bytes, optimized timings are obtained with one sequence including all the bytes versus several sequences of only a few bytes (1 n 256). 7. int(A) corresponds to the upper integer part of A. For instance, int(12/8) = 2, int(32/8) = 4, int(15.3) =16. 40/59 M25P16 Table 16. DC and AC parameters AC characteristics (25 MHz operation) Test conditions specified in Table 10 and Table 12 Symbol Alt. Parameter Min fC fC Clock frequency for the following instructions: FAST_READ, PP, SE, BE, DP, RES, WREN, WRDI, RDSR, WRSR DC Clock frequency for READ instructions fR Max Unit -- 25 MHz DC -- 20 MHz (1) tCLH Clock High time 18 -- -- ns (1) tCLL Clock Low time 18 -- -- ns 0.1 -- -- V/ns tCH tCL Typ tCLCH(2) Clock Rise tCHCL(2) Clock Fall time(3) (peak to peak) 0.1 -- -- V/ns S Active Setup time (relative to C) 10 -- -- ns S Not Active Hold time (relative to C) 10 -- -- ns tSLCH tCSS tCHSL time(3) (peak to peak) tDVCH tDSU Data In Setup time 5 -- -- ns tCHDX tDH Data In Hold time 5 -- -- ns tCHSH S Active Hold time (relative to C) 10 -- -- ns tSHCH S Not Active Setup time (relative to C) 10 -- -- ns 100 -- -- ns tSHSL tCSH S Deselect time tSHQZ(2) tDIS Output Disable time -- -- 15 ns tCLQV tV Clock Low to Output Valid -- -- 15 ns tCLQX tHO Output Hold time 0 -- -- ns tHLCH HOLD Setup time (relative to C) 10 -- -- ns tCHHH HOLD Hold time (relative to C) 10 -- -- ns tHHCH HOLD Setup time (relative to C) 10 -- -- ns tCHHL HOLD Hold time (relative to C) 10 -- -- ns tHHQX(2) tLZ HOLD to Output Low-Z -- 15 ns tHLQZ(2) tHZ HOLD to Output High-Z -- 20 ns tWHSL(4) Write Protect Setup time 20 -- -- ns tSHWL(4) Write Protect Hold time 100 -- -- ns tDP(2) S High to Deep Power-down mode -- -- 3 s tRES1(2) S High to Standby mode without Electronic Signature Read -- -- 3 s tRES2(2) S High to Standby mode with Electronic Signature Read -- -- 1.8 s Write Status Register cycle time -- 15 ms tW(5) 1.5 1. tCH + tCL must be greater than or equal to 1/ fC. 2. Value guaranteed by characterization, not 100% tested in production. 3. Expressed as a slew-rate. 4. Only applicable as a constraint for a WRSR instruction when SRWD is set at `1'. 41/59 DC and AC parameters M25P16 5. Typical values given for TA = 85 C. Figure 23. Serial input timing tSHSL S tCHSL tSLCH tCHSH tSHCH C tDVCH tCHCL tCHDX D Q MSB IN tCLCH LSB IN High Impedance AI01447C Figure 24. Write Protect setup and hold timing during WRSR when SRWD = 1 W tSHWL tWHSL S C D High Impedance Q AI07439 42/59 M25P16 DC and AC parameters Figure 25. Hold timing S tHLCH tCHHL tHHCH C tCHHH tHLQZ tHHQX Q D HOLD AI02032 Figure 26. Output timing S tCH C tCLQV tCLQX tCLQV tCL tSHQZ tCLQX LSB OUT Q tQLQH tQHQL D ADDR.LSB IN AI01449e 43/59 Package mechanical 11 M25P16 Package mechanical In order to meet environmental requirements, Numonyx offers these devices in RoHS compliant packages, which have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. Figure 27. VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead, 6 x 5 mm, package outline A D aaa C A R1 D1 E1 E2 e bbb E M C A B B 2x b aaa C B 0.10 C B 0.10 C A D2 L A2 ddd A A1 A3 C 70-ME 1. Drawing is not to scale. 2. The circle in the top view of the package indicates the position of pin 1. 44/59 M25P16 Package mechanical Table 17. VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead, 6 x 5 mm, package mechanical data millimeters inches Symbol Typ Min Max Typ Min Max A 0.85 0.80 1.00 0.033 0.031 0.039 A1 -- 0.00 0.05 -- 0.000 0.002 A2 0.65 -- -- 0.026 -- -- A3 0.20 -- -- 0.008 -- -- b 0.40 D 6.00 -- 0.35 -- 0.48 0.236 -- -- D1 5.75 -- -- 0.226 -- -- D2 3.40 E 5.00 -- -- 0.197 -- -- E1 4.75 -- -- 0.187 -- -- E2 4.00 3.80 4.30 0.157 0.150 0.169 e 1.27 -- -- 0.050 -- -- R1 0.10 0.00 -- 0.004 0.000 -- L 0.60 0.50 0.75 0.024 0.020 0.029 3.20 0.016 3.60 0.014 0.134 0.019 0.126 0.142 -- -- 12 -- -- 12 aaa -- -- 0.15 -- -- 0.006 bbb -- -- 0.10 -- -- 0.004 ddd -- -- 0.05 -- -- 0.002 45/59 Package mechanical M25P16 Figure 28. VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 x 6 mm, package outline D E E2 e b D2 A L L1 K ddd A1 VDFPN-02 1. Drawing is not to scale. 2. The circle in the top view of the package indicates the position of pin 1. Table 18. VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 x 6 mm, package mechanical data millimeters inches Symbol Typ Min Typ 1.00 0.033 A 0.85 A1 -- 0.00 0.05 b 0.40 0.35 0.48 D 8.00 -- D2 5.16 ddd Min Max 0.039 0.000 0.002 0.016 0.014 0.019 -- 0.315 -- -- -- (1) 0.203 -- -- -- -- 0.05 -- -- 0.002 E 6.00 -- -- 0.236 -- -- E2 4.80 -- -- 0.189 -- -- e 1.27 -- -- 0.050 -- -- 0.82 -- -- 0.032 K L 0.50 0.45 0.60 0.020 0.018 0.024 L1 -- -- 0.15 -- -- 0.006 N 8 1. D2 Max should not exceed (D - K - 2 x L). 46/59 Max 8 M25P16 Package mechanical Figure 29. SO8N - 8 lead plastic small outline, 150 mils body width, package outline h x 45 A2 A c ccc b e 0.25 mm GAUGE PLANE D k 8 E1 E 1 L A1 L1 SO-A 1. Drawing is not to scale. Table 19. SO8N - 8 lead plastic small outline, 150 mils body width, package mechanical data millimeters inches Symbol Typ Min Max Typ Min Max A -- -- 1.75 -- -- 0.069 A1 -- 0.10 0.25 -- 0.004 0.010 A2 -- 1.25 -- -- 0.049 b -- 0.28 0.48 -- 0.011 0.019 c -- 0.17 0.23 -- 0.007 0.009 ccc -- -- 0.10 -- -- 0.004 D 4.90 4.80 5.00 0.193 0.189 0.197 E 6.00 5.80 6.20 0.236 0.228 0.244 E1 3.90 3.80 4.00 0.154 0.150 0.157 e 1.27 -- -- 0.050 -- -- h -- 0.25 0.50 -- 0.010 0.020 k -- 0 8 -- 0 8 L -- 0.40 1.27 -- 0.016 0.050 L1 1.04 -- -- 0.041 -- -- 47/59 Package mechanical M25P16 Figure 30. SO8W - 8 lead plastic small outline, 208 mils body width, package outline A2 A c b CP e D N E E1 1 A1 k L 6L_ME 1. Drawing is not to scale. Table 20. SO8 wide - 8 lead plastic small outline, 208 mils body width, package mechanical data millimeters inches Symbol Typ Min Max Typ Min Max A -- -- 2.50 -- -- 0.098 A1 -- 0.00 0.25 -- 0.000 0.010 A2 -- 1.51 2.00 -- 0.059 0.079 b 0.40 0.35 0.51 0.016 0.014 0.020 c 0.20 0.10 0.35 0.008 0.004 0.014 CP -- -- 0.10 -- -- 0.004 D -- -- 6.05 -- -- 0.238 E -- 5.02 6.22 -- 0.198 0.245 E1 -- 7.62 8.89 -- 0.300 0.350 e 1.27 -- -- 0.050 -- -- k -- 0 10 -- 0 10 L -- 0.50 0.80 -- 0.020 0.031 N 48/59 8 8 M25P16 Package mechanical Figure 31. SO16 wide - 16-lead plastic small outline, 300 mils body width, package outline D 16 h x 45 9 C E 1 H 8 A2 B A1 A L ddd e SO-H 1. Drawing is not to scale. Table 21. SO16 wide - 16-lead plastic small outline, 300 mils body width, mechanical data millimeters inches Symbol Typ Min Max Typ Min Max A -- 2.35 2.65 -- 0.093 0.104 A1 -- 0.10 0.30 -- 0.004 0.012 B -- 0.33 0.51 -- 0.013 0.020 C -- 0.23 0.32 -- 0.009 0.013 D -- 10.10 10.50 -- 0.398 0.413 E -- 7.40 7.60 -- 0.291 0.299 e 1.27 -- -- 0.050 -- -- H -- 10.00 10.65 -- 0.394 0.419 h -- 0.25 0.75 -- 0.010 0.030 L -- 0.40 1.27 -- 0.016 0.050 -- 0 8 -- 0 8 ddd -- -- 0.10 -- -- 0.004 49/59 Package mechanical M25P16 Figure 32. PDIP8 - 8 lead Plastic Small Outline, 300 mils body width, package outline E b2 A2 A1 b A L c e eA eB D 8 E1 1 PDIP-B 1. Package is not to scale. Table 22. PDIP8 - 8 lead Plastic Small Outline, 300 mils body width, package mechanical data millimeters inches Symbol 50/59 Typ Min Max Typ Min Max A -- -- 4.80 -- -- 0.188 A1 0.50 -- -- 0.019 -- -- A2 3.10 3.30 3.50 0.122 0.129 0.137 b 0.38 -- 0.55 0.014 -- 0.021 b2 1.47 1.52 1.57 0.057 0.059 0.061 c 0.21 -- 0.35 0.008 -- 0.013 D 9.10 9.20 9.30 0.358 0.362 0.366 E 7.62 7.87 8.25 0.300 0.309 0.324 E1 6.25 6.35 6.45 0.246 0.250 0.253 e -- 2.54 -- -- 0.100 -- eA -- 7.62 -- -- 0.300 -- eB 7.62 8.80 10.90 0.300 0.346 0.429 L 2.92 3.30 3.81 0.114 0.122 0.150 M25P16 Package mechanical Figure 33. UFDFPN (MLP8) 8-lead ultra thin fine pitch dual flat package no lead, 4X3 mm package mechanical data 1. Drawing is not to scale. 51/59 Package mechanical M25P16 Table 23. UFDFPN (MLP8) 8-lead ultra thin fine pitch dual flat package no lead, 4X3 mm package mechanical data(1) Databook (mm) Drawing (mm) Symbol Typ Min Max Typ Min Max A 0.55 0.45 0.60 0.55 0.45 0.60 A1 0.02 0.00 0.05 0.02 0.00 0.05 A3 0.127 0.15 0.127 0.15 0 12 0 12 D2 0.80 0.70 0.90 0.80 0.70 0.90 E2 0.20 0.10 0.30 0.20 0.10 0.30 e 0.80 0.80 N(2) 8 8 4 4 ND (3) b(4) 0.30 0.25 0.35 0.30 0.25 0.35 L 0.60 0.55 0.65 0.60 0.55 0.65 D 4.00 3.90 4.10 4.00 3.90 4.10 E 3.00 2.90 3.10 3.00 2.90 3.10 1. Maximum package warpage is 0.05 mm; maximum allowable burrs is 0.076 mm in all directions; and bilateral coplanarity zone applies to the exposed heat sink slug as well as the terminals.N is the total number of terminals. 2. N is the total number of terminals. 3. ND refers to the number of terminals on D side. 4. Dimension b applies to metallized terminal and is measured between 0.15 and 0.30mm From terminal tip. if the terminal has the optional radius on the other end of the terminal, The dimension b should not be measured in that radius area. 52/59 M25P16 Ordering Information, Standard Parts 12 Ordering Information, Standard Parts Table 24. Ordering information scheme Example: M25P16 - V MN 6 T P B A Device type M25P = Serial Flash memory for code storage Device function 16 = 16 Mbit (2 Mbit x 8) Security features(1) - = no extra security S = CFD programmed with UID Operating voltage V = VCC = 2.7 V to 3.6 V Package MP = VFDFPN8 6 x 5 mm (MLP8) ME = VDFPN8 8 x 6 mm (MLP8)(2) MN = SO8N (150 mils width) MW = SO8W (208 mils width) MF = SO16 (300 mils width) BA = PDIP8 (300 mils width) MC = UFDFPN8 (MLP8), 4 x 3 mm Device grade 6 = Industrial temperature range, -40 to 85 C. Device tested with standard test flow 3(3) = Automotive temperature range, -40 to 125 C. Device tested with high reliability certified flow.(4) Option blank = Standard packing T = Tape and reel packing Plating Technology P or G = RoHS compliant Lithography blank = 110nm, Catania Diffusion Plant B = 110nm, Fab.2 Diffusion Plant Automotive Grade A(4) = Automotive -40 C to 125 C Part Device tested with high reliability certified flow(3). blank = standard -40 to 85 C device 1. Secure options are available upon customer request. 2. Not for new design, please use MP package version of the device. 3. Device grade 3 available in an SO8 RoHS compliant package. 53/59 Ordering Information, Standard Parts M25P16 4. Numonyx strongly recommends the use of the Automotive Grade devices (AutoGrade 6 and Grade 3) for use in an automotive environment. The High Reliability Certified Flow (HRCF) is described in the quality note QNEE9801. Note: 54/59 For a list of available options (speed, package, etc.), for further information on any aspect of this device or when ordering parts operating at 75 MHz (0.11 m, process digit `4'), please contact your nearest Numonyx Sales Office. M25P16 Ordering Information, Automotive Parts 13 Ordering Information, Automotive Parts Table 25. Ordering information scheme Example: M25P16 - V MN 6 T P B A Device type M25P = Serial Flash memory for code storage Device function 16 = 16 Mbit (2 Mbit x 8) Security features - = no extra security Operating voltage V = VCC = 2.3 to 3.6 V Package MN = SO8N (150 mils width) MF = SO16 (300 mils width) Device grade 6 = Industrial temperature range, -40 to 85 C. Device tested with high reliability certified flow 3 = Automotive temperature range, -40 to 125 C. Device tested with high reliability certified flow. Option blank = Standard packing T = Tape and reel packing Plating Technology P or G = RoHS compliant Lithography /4 = 110nm, Catania Diffusion Plant (not suggested for new design) B = 110nm, Fab.2 Diffusion Plant Automotive Grade blank = Automotive -40 to 125 C part A = Automotive -40 C to 85 C part (used ONLY in conjunction with Device Grade 6 to distinguish the Auto Tested Parts from the non Auto Tested parts). Note: Numonyx strongly recommends the use of the Automotive Grade devices (Auto Grade 6 and 3) in an automotive envirnoment. The high reliability certified flow (HRCF) is described in the quality note QNEE9801. Please ask your Numonyx sales office for a copy. 55/59 Revision history 14 Revision history Table 26. Document revision history Date Revision 16-Jan-2002 0.1 Target Specification Document written 0.4 Clarification of descriptions of entering Standby Power mode from Deep Power-down mode, and of terminating an instruction sequence or dataout sequence. ICC2(max) value changed to 10A 13-Dec-2002 0.5 Typical Page Program time improved. Write Protect setup and hold times specified, for applications that switch Write Protect to exit the Hardware Protection mode immediately before a WRSR, and to enter the Hardware Protection mode again immediately after 15-May2003 0.6 MLP8 package added 0.7 50MHz operation, and RDID instruction added. Published internally, only 20-Jun-2003 0.8 8x6 MLP8 and SO16(300 mil) packages added 24-Sep-2003 1.0 tPP, tSE and tBE revised. SO16 package code changed. Output Timing Reference Voltage changed. Document promoted to Preliminary Data. 24-Nov-2003 2.0 Table of contents, warning about exposed paddle on MLP8, and Pb-free options added. Value of tVSL(min) and tBE(typ) changed. Change of naming for VDFPN8 packages. Document promoted to full Datasheet. 17-May2004 3.0 MLP8(5x6) package removed. Soldering temperature information clarified for RoHS compliant devices. Device Grade clarified 01-Apr-2005 4.0 Notes 1 and 2 removed from Table 24: Ordering information scheme. Small text changes. Read Identification (RDID), Deep Power-down (DP) and Release from Deep Power-down and Read Electronic Signature (RES) instructions, and Active Power, Standby Power and Deep Power-down modes paragraph clarified. 01-Aug-2005 5.0 Updated Page Program (PP) instructions in Page programming, Page Program (PP) and Table 15: AC characteristics (Grade 6). 6.0 VFQFPN8 package added (see Figure 27: VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead, 6 x 5 mm, package outline and Table 17: VFQFPN8 (MLP8) 8-lead very thin fine pitch quad flat package no lead, 6 x 5 mm, package mechanical data). All packages are RoHS compliant. "Blank" option removed under Plating Technology. 27-Feb-2006 7 SO8 Narrow and SO8 Wide packages added (see Section 11: Package mechanical). VDFPN8 package updated (see Table 18: VDFPN8 (MLP8) 8-lead very thin dual flat package no lead, 8 x 6 mm, package mechanical data). Note 2 added to Table 24: Ordering information scheme. 04-Jul-2006 8 Figure 4: Bus master and memory devices on the SPI bus updated and Note 2 added. SO8N package specifications updated (see Figure 29 and Table 19). Small text changes. 23-Apr-2002 20-Oct-2005 56/59 M25P16 Changes M25P16 Revision history Table 26. Date Document revision history (continued) Revision Changes 9 Page Program, Sector Erase and Bulk Erase updated in Features. VIO max modified in Table 9: Absolute maximum ratings. Table 15: AC characteristics (110 nm technology) added. VFQFPN8 package specifications updated (see Table 17). Note 1 added to Table 18. Note: on page 54 modified. 10 Small text changes. Hardware Write protection added to Features. VCC supply voltage and VSS ground signal descriptions added. Figure 4: Bus master and memory devices on the SPI bus modified, note 2 removed and replaced by an explanatory paragraph. Write In Progress bit behavior specified at Power-up (see Section 7: Power-up and powerdown). TLEAD added to Table 9: Absolute maximum ratings. Grade 3 temperature range added. Table 11: Data retention and endurance and Table 16: AC characteristics (25 MHz operation) added. SO8W and VFQFPN8 package specifications updated (see Section 11: Package mechanical). 11 Eliminated the reference to the Deep Power-down mode and updated the Read Identification instruction in Section 6.3: Read Identification (RDID). Inserted UID and CFI content columns in Table 5: Read Identification (RDID) data-out sequence. Modified Data bytes for RDID instruction in Table 4: Instruction set. Modified Q signal in Figure 10: Read Identification (RDID) instruction sequence and data-out sequence. Modified Test condition and maximum values for ICC3 in Table 14: DC characteristics. Eliminated Table 15: AC characteristics (Grade 6). Modified the maximum value for fC in Table 15: AC characteristics (110 nm technology). 31-Oct-2007 12 Removed `low voltage' from the title. Changed the typical time for Bulk Erase on page 1. Section 6.3: Read Identification (RDID) updated. Added note 2 and 3 to Table 9: Absolute maximum ratings. Modified maximum value for tCLQV in Table 15: AC characteristics (110 nm technology). 10-Dec-2007 13 Applied Numonyx branding. 20-Jun 2008 14 Added a reference to customer's ability to request dedicated part number in Section 6.3: Read Identification (RDID) on page 20. Moved specifications in "max" column to "min" column and changed the "min" for grade 3 to 10,000 in Table 11: Data retention and endurance on page 37. Deleted "grade 6" reference in Table 15: AC characteristics (110 nm technology) on page 39. Deleted "grade 3" reference and "preliminary note" in Table 16: AC characteristics (25 MHz operation) on page 41. Revised Section 12: Ordering Information, Standard Parts on page 53. 5-Dec-2008 15 Added the PDIP8 (BA), 300 mils width package information. 10-Oct-2006 09-Jan-2007 15-Jun-2007 57/59 Revision history Table 26. 58/59 M25P16 Document revision history (continued) Date Revision Changes 6-March 2008 16 Added "Automotive Certified Parts" information to cover page, data retention table, AC Characteristics table, and ordering information. 3-August2009 17 Made changes to the following tables: Table 8.: Power-up timing and VWI threshold - vWI changed min and max from 1.5 / 2.5 to 1.0 / 2.1 V respectively. Table 14.: DC characteristics - ICC3 (Read) changed from 12 mA to 8 mA. Table 16.: AC characteristics (25 MHz operation) - Removed tPP, tSE, and tBE, and the associated notes. 14-Oct-2009 18 Created separate order information for standard parts and automotive parts. 23-Feb-2010 19 Added the following package information: Figure 33.: UFDFPN (MLP8) 8-lead ultra thin fine pitch dual flat package no lead, 4X3 mm package mechanical data. 14-April2010 20 Corrected package nomenclature. M25P16 Please Read Carefully: INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYXTM PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Numonyx may make changes to specifications and product descriptions at any time, without notice. Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Numonyx reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by visiting Numonyx's website at http://www.numonyx.com. Numonyx StrataFlash(R) and Numonyx(R) ForteTM Serial Flash Memory are trademarks or registered trademarks of Numonyx or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) 2010, Numonyx, B.V., All Rights Reserved. 59/59