Product family data sheet
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are
registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
WWW.CREE.COM/XLAMP
CLD-DS52 REV 3I
Cree® XLamp® XQ-D LED
PRODUCT DESCRIPTION
Cree XLamp® XQ-D LEDs revolutionize
low-cost, high-power LEDs by delivering
lighting-class reliability and a wider
spread of light than typical plastic
packages. The XQ-D’s innovative
wide light emission can improve the
omnidirectionality of replacement lamps,
while also reducing system cost by using
fewer LEDs.
Using Cree’s newest generation of
silicon carbide-based LED chips, XQ-D is
optimized to dramatically lower system
cost in replacement lamp, non-directional
and outdoor area lighting applications.
FEATURES
• Cree’s smallest lighting class LED:
1.6X1.6X1.6mm
• Available in white, 80-minimum CRI
white, and 70-minimum CRI cool
white
• Binnedat25°C
• 700mAmaximumdrivecurrent
• Lowthermalresistance:7.5°C/W
• Wideviewingangle:145°
• Reowsolderable-JEDEC
J-STD-020Ccompatible
• Unlimitedoorlifeat≤30°C/85%RH
• RoHSandREAChcompliant
• UL® recognized component
(E349212)
TABLE OF CONTENTS
Characteristics ....................................... 2
FluxCharacteristics ............................... 3
Relative Spectral Power Distribution .... 4
RelativeFluxvs.Junction
Temperature ........................................... 4
Electrical Characteristics ....................... 5
RelativeFluxvs.Current ........................ 5
Typical Spatial Distribution .................... 6
Thermal Design ...................................... 6
ReowSolderingCharacteristics .......... 7
Notes ...................................................... 8
Mechanical Dimensions ...................... 10
Tape and Reel ....................................... 11
Packaging ............................................. 12
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
2
XLamp® XQ-D LED
CHARACTERISTICS
Characteristics Unit Minimum Typical Maximum
Thermal resistance, junction to solder point °C/W 7.5
Viewingangle(FWHM) degrees 145
Temperaturecoefcientofvoltage mV/°C -3
ESDclassication(HBMperMil-Std-883D) Class 1
DC forward current mA 350 700
Reverse voltage V -5
Forwardvoltage(@350mA,25°C) V 3.1 3.5
LED junction temperature °C 150
2
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
3
XLamp® XQ-D LED
FLUX CHARACTERISTICS (TJ=25°C)
The following table provides several base order codes for XLamp XQ-D LEDs. It is important to note that the base order codes listed here
are a subset of the total available order codes for the product family. For more order codes, as well as a complete description of the order-
code nomenclature, please consult the XLamp XQ LED Family Binning and Labeling document.
Color
CCT Range Minimum Luminous Flux
@ 350mA
Calculated
Minimum
Luminous Flux
(lm)* Order Code
Min. Max. Group Flux (lm) 700 mA
CoolWhite 5000 K 8300 K
R4 130 227 XQDAWT-00-0000-00000LG51
R3 122 213 XQDAWT-00-0000-00000LF51
R2 114 199 XQDAWT-00-0000-00000LE51
70 CRI Minimum
CoolWhite 5000 K 8300 K
R4 130 227 XQDAWT-00-0000-00000BG51
R3 122 213 XQDAWT-00-0000-00000BF51
R2 114 199 XQDAWT-00-0000-00000BE51
NeutralWhite 3700 K 5000 K
R3 122 213 XQDAWT-00-0000-00000BFE5
R2 114 199 XQDAWT-00-0000-00000BEE5
Q5 107 187 XQDAWT-00-0000-00000LDE5
80 CRI Minimum
White 2600 K 4300K
Q4 100 172 XQDAWT-00-0000-00000HCE7
Q3 93.9 164 XQDAWT-00-0000-00000HBE7
Q2 87.4 153 XQDAWT-00-0000-00000HAE7
WarmWhite 2600 K 3700 K
Q4 100 172 XQDAWT-00-0000-00000LCE7
Q3 93.9 164 XQDAWT-00-0000-00000LBE7
Q2 87.4 153 XQDAWT-00-0000-00000LAE7
Notes:
• Creemaintainsatoleranceof±7%onuxandpowermeasurements,±0.005onchromaticity(CCx,CCy)measurementsand±2onCRI
measurements.SeetheMeasurementssection(page8).
• TypicalCRIforNeutralWhite,3700K-5000KCCTis75.
• TypicalCRIforWarmWhite,2600K-3700KCCTis80.
• MinimumCRIfor70CRIMinimumCoolWhiteis70.
• MinimumCRIfor80CRIMinimumWhiteis80.
* Calculateduxvaluesat700mAareforreferenceonly.
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
4
XLamp® XQ-D LED
RELATIVE SPECTRAL POWER DISTRIBUTION
RELATIVE FLUX VS. JUNCTION TEMPERATURE (IF=350mA)
Relative Spectral Power
0%
20%
40%
60%
80%
100%
380 430 480 530 580 630 680 730 780
Relative Radiant Power (%)
Wavelength (nm)
Cool White
Neutral White
Warm White
Relative Flux Output vs. Junction Temperature
0%
20%
40%
60%
80%
100%
120%
25 50 75 100 125 150
Relative Luminous Flux
Junction Temperature (ºC)
4
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
5
XLamp® XQ-D LED
ELECTRICAL CHARACTERISTICS (TJ=25°C)
RELATIVE FLUX VS. CURRENT (TJ=25°C)
Electrical Characteristics (Tj = 85ºC)
0
100
200
300
400
500
600
700
2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2 3.3
Forward Current (mA)
Forward Voltage (V)
Relative Intensity vs. Current (Tj = 85ºC)
0%
20%
40%
60%
80%
100%
120%
140%
160%
180%
0100 200 300 400 500 600 700
Relative Luminous Flux (%)
Forward Current (mA)
5
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
6
XLamp® XQ-D LED
TYPICAL SPATIAL DISTRIBUTION
THERMAL DESIGN
ThemaximumforwardcurrentisdeterminedbythethermalresistancebetweentheLEDjunctionandambient.Itiscrucialfortheend
product to be designed in a manner that minimizes the thermal resistance from the solder point to ambient in order to optimize lamp life
and optical characteristics.
Typical Spatial Radiation Pattern
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
-90 -70 -50 -30 -10 10 30 50 70 90
Relative Luminous Intensity (%)
Angle (º)
Thermal Design
0
100
200
300
400
500
600
700
800
020 40 60 80 100 120 140 160
Maximum Current (mA)
Ambient Temperature (ºC)
Rj-a = 10°C/W
Rj-a = 15°C/W
Rj-a = 20°C/W
Rj-a = 25°C/W
6
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
7
XLamp® XQ-D LED
7
REFLOW SOLDERING CHARACTERISTICS
Intesting,CreehasfoundXLampXQ-DLEDstobecompatiblewithJEDECJ-STD-020C,usingtheparameterslistedbelow.Asageneral
guideline,Creerecommendsthatusersfollowtherecommendedsolderingproleprovidedbythemanufacturerofthesolderpasteused,
and therefore it is the lamp or luminaire manufacturer’s responsibility to determine applicable soldering requirements.
NotethatthisgeneralguidelinemaynotapplytoallPCBdesignsandcongurationsofreowsolderingequipment.
Profile Feature Lead-Free Solder
Average Ramp-Up Rate (TsmaxtoTp) 1.2°C/second
Preheat: Temperature Min (Tsmin) 120°C
Preheat:TemperatureMax(Tsmax) 170°C
Preheat: Time (tsmin to tsmax)65-150 seconds
Time Maintained Above: Temperature (TL) 217°C
Time Maintained Above: Time (tL) 45-90seconds
Peak/ClassicationTemperature(Tp) 235-245°C
TimeWithin5°CofActualPeakTemperature(tp) 20-40seconds
Ramp-Down Rate 1-6°C/second
Time25°CtoPeakTemperature 4minutesmax.
Note: All temperatures refer to topside of the package, measured on the package body surface.
IPC/JEDECJ-STD-020C
TP
TL
Temperature
Time
t 25˚C to Peak
Preheat
ts
tS
tP
25
Ramp-down
Ramp-up
Critical Zone
TL to TP
Tsmax
Tsmin
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
8
XLamp® XQ-D LED
8
NOTES
Measurements
Theluminousux,radiantpower,chromaticity,forwardvoltageandCRImeasurementsinthisdocumentarebinningspecicationsonly
and solely represent product measurements as of the date of shipment. These measurements will change over time based on a number
offactorsthatarenotwithinCree’scontrolandarenotintendedorprovidedasoperationalspecicationsfortheproducts.Calculated
valuesareprovidedforinformationalpurposesonlyandarenotintendedorprovidedasspecications.
Pre‑Release Qualication Testing
Please read the LED Reliability OverviewfordetailsofthequalicationprocessCreeappliestoensurelong-termreliabilityforXLamp
LEDsanddetailsofCree’spre-releasequalicationtestingforXLampLEDs.
Lumen Maintenance
CreenowusesstandardizedIESLM-80-08andTM-21-11methodsforcollectinglong-termdataandextrapolatingLEDlumenmaintenance.
ForinformationonthespecicLM-80datasetsavailableforthisLED,refertothepublicLM-80 results document.
Please read the Long-Term Lumen Maintenance application note for more details on Cree’s lumen maintenance testing and forecasting.
Please read the Thermal Management application note for details on how thermal design, ambient temperature, and drive current affect
the LED junction temperature.
Moisture Sensitivity
CreerecommendskeepingXLampLEDsintheprovided,resealablemoisture-barrierpackaging(MBP)untilimmediatelypriortosoldering.
Unopened MBPs that contain XLamp LEDs do not need special storage for moisture sensitivity.
OncetheMBPisopened,XLampXQ-DLEDsmaybestoredasMSL1perJEDECJ-STD-033,meaningtheyhaveunlimitedoorlifein
conditionsof≤30ºC/85%relativehumidity(RH).Regardlessofstoragecondition,CreerecommendssealinganyunsolderedLEDsinthe
original MBP.
RoHS Compliance
ThelevelsofRoHSrestrictedmaterialsinthisproductarebelowthemaximumconcentrationvalues(alsoreferredtoasthethreshold
limits)permittedforsuchsubstances,orareusedinanexemptedapplication,inaccordancewithEUDirective2011/65/EC(RoHS2),as
implementedJanuary2,2013.RoHSDeclarationsforthisproductcanbeobtainedfromyourCreerepresentativeorfromtheProduct
Ecology section of the Cree website.
REACh Compliance
REAChsubstancesofveryhighconcern(SVHCs)informationisavailableforthisproduct.SincetheEuropeanChemicalAgency(ECHA)
haspublishednoticeoftheirintenttofrequentlyrevisetheSVHClistingfortheforeseeablefuture,pleasecontactaCreerepresentativeto
insureyougetthemostup-to-dateREAChSVHCDeclaration.REAChbannedsubstanceinformation(REAChArticle67)isalsoavailable
upon request.
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
9
XLamp® XQ-D LED
UL® Recognized Component
This product meets the requirements to be considered a UL Recognized Component with Level 1 enclosure consideration. The LED
packageoraportionthereofhasnotbeeninvestigatedasareenclosureorareandelectricalenclosureperANSI/UL8750.
Vision Advisory
WARNING:Donotlookatanexposedlampinoperation.Eyeinjurycanresult.FormoreinformationaboutLEDsandeyesafety,please
refer to the LED Eye Safety application note.
NOTES - CONTINUED
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
10
XLamp® XQ-D LED
MECHANICAL DIMENSIONS
All dimensions in mm.
Measurement tolerances unless indicated otherwise: ±.13 mm
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
1.60
1.60 1.41
.600 .600
.300
1.500
1.60± .05
.30
1.60
.65
1.60
.300
1.500
3.300
3.300
1/145.000
A
2610-00026
XQx OUTLINE
--
--
----
----
5/23/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PC BOARD SOLDER PAD
RECOMMENDED TRACE LAYOUT
SOLDER PAD
REFERENCE
NOTCH IS ON
CATHODE (-) SIDE
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
1.60
1.60
1.41
.600 .600
.300
1.500
1.60± .05
.30
1.60
.65
1.60
.300
1.500
3.300
3.300
1/145.000
A
2610-00026
XQx OUTLINE
--
--
----
----
5/23/12D. CRONIN
REVISONS
REV DESCRIPTION BY DATE APP'D
RECOMMENDED PC BOARD SOLDER PAD
RECOMMENDED TRACE LAYOUT
SOLDER PAD
REFERENCE
NOTCH IS ON
CATHODE (-) SIDE
1.60
1.60
Top View Side View Bottom View
.30
1.60
.65
1.60
.300
1.500
3.300
3.300
1.60
1.60
1.58 ±.08
1.500
.600 .600
.300
R.936
.375
RECOMMENDED PC BOARD SOLDER PAD
RECOMMENDED TRACE LAYOUT
SOLDER PAD
REFERENCE
NOTCH IS ON
CATHODE(-) SIDE
.30
1.60
.65
1.60
.300
1.500
3.300
3.300
1.60
1.60
1.58 ±.08
1.500
.600 .600
.300
R.936
.375
RECOMMENDED PC BOARD SOLDER PAD
RECOMMENDED TRACE LAYOUT
SOLDER PAD
REFERENCE
NOTCH IS ON
CATHODE(-) SIDE
Recommended trace layout
Recommended PCB solder pad
10
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
11
XLamp® XQ-D LED
11
TAPE AND REEL
AllCreecarriertapesconformtoEIA-481D,AutomatedComponentHandlingSystemsStandard.
Exceptasnoted,alldimensionsinmm.
Measurementtolerancesunlessindicatedotherwise:.xx=±.25mm,.xxx=±.125mm
SIZE
TITLE
OF
REV.
SHEET
C
DRAWING NO.
DATE
DATE
DATE
CHECK
FINAL PROTECTIVE FINISH
MATERIAL
APPROVED
DRAWN BY
THIRD ANGLE PROJECTION
SCALE
A
B
C
D
123456
6 5 4 3 2 1
A
B
C
D
Phone (919) 313-5300
Fax (919) 313-5558
4600 Silicon Drive
Durham, N.C 27703
UNAUTHORIZED PERSON WITHOUT
THE WRITTEN CONSENT
MAY NOT BE COPIED, REPRODUCED OR DISCLOSED TO ANY
CONFIDENTIAL INFORMATION OF CREE, INC. THIS PLOT
CONTAINED WITHIN ARE THE PROPRIETARY AND
CREE CONFIDENTIAL. THIS PLOT AND THE INFORMATION
OF CREE INC.
NOTICE
X° ± .5 °
.XXX ± .25
.XX ± .75
.X ± 1.5
FOR SHEET METAL PARTS ONLY
.XX ± .25
.XXX ± .125
X° ± .5 °
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN
MILLIMETERS AND AFTER FINISH.
TOLERANCE UNLESS SPECIFIED:
SURFACE FINISH:
1.6
A
A
.30 ± .10
3.50 ±.10
1.85
1.65
1.750
8.000
NOMINAL
8.30
MAX
1.000
+.10
-.00
1.500
4.000
2.000
REVISONS
REV DESCRIPTION BY DATE APP'D
1/14.000
A
2402-00023
Carrier Tape, 1.7X1.7 XPQ
5/31/12D. CRONIN
Notes:
1. 10 sprocket hole pitch cumulative tolerance ± 0.2mm
REFERENCE VENDOR PART NUMBER 021142
CATHODE SIDE
ANODE SIDE
Loaded Pockets
(2,000 Lamps)
Leader
400 mm (min) of
empty pockets with
at least 100 mm
sealed by tape
(50 empty pockets min.)
Trailer
160 mm (min) of
empty pockets
sealed with tape
(20 pockets min.)
START
END
Cathode Side
Anode Side
(denoted by + and circle)
2.5
±.1
1.5
±.1
8.0
±.1
4.0
±.1
1.75
±.10
12.0 .0
+
.3
13
mm
7"
Cover Tape
Pocket Tape
User Feed Direction
User Feed Direction
Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
12
XLamp® XQ-D LED
12
Patent Label
(on bottom of box)
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Bin Code,
Quantity, Reel ID
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Order Code,
Quantity, Reel ID, PO #
Label with Cree Bin Code,
Quantity, Reel ID
Unpackaged Reel
Packaged Reel
Boxed Reel
CREE Bin Code
& Barcode Label
Vacuum-Sealed
Moisture Barrier Bag
Label with Customer
P/N, Qty, Lot #, PO #
Label with Cree Bin
Code, Qty, Lot #
Label with Cree Bin
Code, Qty, Lot #
Vacuum-Sealed
Moisture Barrier Bag
Patent Label
Label with Customer Order
Code, Qty, Reel ID, PO #
PACKAGING
The diagrams below show the packaging and labels Cree uses to ship XLamp XQ-D LEDs. XLamp XQ-D LEDs are shipped in tape loaded
onareel.Eachboxcontainsonlyonereelinamoisturebarrierbag.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Cree, Inc.:
XQDAWT-00-0000-00000HBE7 XQDAWT-00-0000-00000HBE8 XQDAWT-00-0000-00000HDE1 XQDAWT-00-0000-
00000HDE2 XQDAWT-00-0000-00000HDE3 XQDAWT-00-0000-00000HDE5 XQDAWT-00-0000-00000BCE8
XQDAWT-00-0000-00000BCF8 XQDAWT-00-0000-00000BDE6 XQDAWT-00-0000-00000BDE7 XQDAWT-00-0000-
00000BDE8 XQDAWT-00-0000-00000BDF6 XQDAWT-00-0000-00000BDF7 XQDAWT-00-0000-00000BDF8
XQDAWT-00-0000-00000BE50 XQDAWT-00-0000-00000BE51 XQDAWT-00-0000-00000BE53 XQDAWT-00-0000-
00000BEE1 XQDAWT-00-0000-00000BEE2 XQDAWT-00-0000-00000BEE3 XQDAWT-00-0000-00000BEE4
XQDAWT-00-0000-00000BEE5 XQDAWT-00-0000-00000BEE6 XQDAWT-00-0000-00000BEE7 XQDAWT-00-0000-
00000BEE8 XQDAWT-00-0000-00000BEF4 XQDAWT-00-0000-00000BEF5 XQDAWT-00-0000-00000BEF6
XQDAWT-00-0000-00000BEF7 XQDAWT-00-0000-00000BEF8 XQDAWT-00-0000-00000BF50 XQDAWT-00-0000-
00000BF51 XQDAWT-00-0000-00000BF53 XQDAWT-00-0000-00000BFE1 XQDAWT-00-0000-00000BFE2
XQDAWT-00-0000-00000BFE3 XQDAWT-00-0000-00000BFE4 XQDAWT-00-0000-00000BFE5 XQDAWT-00-0000-
00000BFE6 XQDAWT-00-0000-00000BFE7 XQDAWT-00-0000-00000BFF4 XQDAWT-00-0000-00000BFF5
XQDAWT-00-0000-00000BFF6 XQDAWT-00-0000-00000BFF7 XQDAWT-00-0000-00000BG50 XQDAWT-00-0000-
00000BG51 XQDAWT-00-0000-00000BG53 XQDAWT-00-0000-00000BGE1 XQDAWT-00-0000-00000BGE2
XQDAWT-00-0000-00000BGE3 XQDAWT-00-0000-00000BGE4 XQDAWT-00-0000-00000BGF4 XQDAWT-00-0000-
00000HBF7 XQDAWT-00-0000-00000HBF8 XQDAWT-00-0000-00000HCE6 XQDAWT-00-0000-00000HCE7
XQDAWT-00-0000-00000HCE8 XQDAWT-00-0000-00000HCF6 XQDAWT-00-0000-00000HCF7 XQDAWT-00-0000-
00000HCF8 XQDAWT-00-0000-00000HDE4 XQDAWT-00-0000-00000HDE6 XQDAWT-00-0000-00000HDE7
XQDAWT-00-0000-00000HDE8 XQDAWT-00-0000-00000HDF4 XQDAWT-00-0000-00000HDF5 XQDAWT-00-0000-
00000HDF6 XQDAWT-00-0000-00000HDF7 XQDAWT-00-0000-00000HDF8 XQDAWT-00-0000-00000HE50
XQDAWT-00-0000-00000HE51 XQDAWT-00-0000-00000HE53 XQDAWT-00-0000-00000HEE1 XQDAWT-00-0000-
00000HEE2 XQDAWT-00-0000-00000HEE3 XQDAWT-00-0000-00000HEE4 XQDAWT-00-0000-00000HEE5
XQDAWT-00-0000-00000HEE6 XQDAWT-00-0000-00000HEE7 XQDAWT-00-0000-00000HEF4 XQDAWT-00-0000-
00000HEF5 XQDAWT-00-0000-00000HEF6 XQDAWT-00-0000-00000HEF7 XQDAWT-00-0000-00000HF50
XQDAWT-00-0000-00000HF51 XQDAWT-00-0000-00000HF53 XQDAWT-00-0000-00000HFE1 XQDAWT-00-0000-
00000HFE2 XQDAWT-00-0000-00000HFE3 XQDAWT-00-0000-00000HFE4 XQDAWT-00-0000-00000HFF4
XQDAWT-00-0000-00000LCE7 XQDAWT-00-0000-00000LCE8 XQDAWT-00-0000-00000LCF7 XQDAWT-00-0000-
00000LCF8 XQDAWT-00-0000-00000LDE4 XQDAWT-00-0000-00000LDE5 XQDAWT-00-0000-00000LDE6
XQDAWT-00-0000-00000LDE7 XQDAWT-00-0000-00000LDE8