CJ-series CompoBus/S Master Unit CJ1W-SRM21 CSM_CJ1W-SRM21_DS_E_2_2 CompoBus/S is a high-speed I/O bus CJ1W-SRM21 Features * * * * * Up to 256 I/O points per Master. Up to 32 Slaves per Master. Communications cycle time: 0.5 ms (at 750 kbps). Communications distance: Up to 500 m (at 93.75 kbps). Free wiring with any branching method for up to 200 m (in long-distance communications mode). System Configuration Compobus/s Master Unit CJ1W-SRM21 Remote Input Terminals Photoelectric Sensors, Proximity Sensors, or Limit Switches Remote Input Terminals (3-tier terminal block) Photoelectric Sensors, Proximity Sensors, Limit Switches Fiber Amplifier Communications Units Fiber Amplifier Units Remote Output Terminals Remote Output Terminals (3-tier terminal block) Remote I/O Terminals (3-tier terminal block) Connector I/O Terminals Solenoids or valves Photoelectric Sensors or Proximity Sensors with connectors Solenoids or valves Remote I/O Module Sensor Terminals Analog Input Terminal Analog Output Terminal CPM2A or CPM1A Terminal-block Terminator I/O Link Unit for CPM1A/CPM2A PCB Optical Fiber Sensors 1 to 5 V, 4 to 20 mA Inverters or valves Note: Production will be discontinued in March 2015. 1 CJ1W-SRM21 Communication Specifications Item Specification Communications method Special CompoBus/S protocol Communications baud rate High-speed Communications Mode: 750 kbps Long-distance Communications Mode: 93.75 kbps Modulation method Baseband method Coding method Manchester coding method Error control checks Manchester code check, frame length check, and parity check Cable VCTF cable (JIS C 3306) Two 0.75 mm2 conductors (2 signal wires) Four 0.75 mm2 conductors (2 signal wires and 2 power supply wires) Special Flat Cable Four 0.75 mm2 conductors (2 signal wires and 2 power supply wires) 2-conductor VCTF cable Communications distance 4-conductor VCTF cable High-speed Communications Mode Main line length: 100 m max. Branch line length: 3 m max. Total branch line length: 50 m max. Long-distance Communications Mode Main line length: 500 m max. Branch line length: 6 m max. Total branch line length: 120 m max. High-speed Communications Mode Main line length: 30 m max. Branch line length: 3 m max. Total branch line length: 30 m max. Long-distance Communications Mode: Flexibly branched, provided that the total length of cable is a maximum of 200 m. Special Flat Cable High-speed Communications Mode Main line length: 30 m max. Branch line length: 3 m max. Total branch line length: 30 m max. When 4-conductor VCTF cable or Special Flat Cable is used to connect fewer than 16 Slaves, the main line can be up to 100 m long and the total branch line length can be up to 50 m in High-speed Communications Mode. Long-distance Communications Mode: Flexibly branched, provided that the total length of cable is a maximum of 200 m. Ordering Information International Standards * The standards are abbreviated as follows: U: UL, U1: UL (Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus (Class I Division 2 Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, and CE: EC Directives. * Contact your OMRON representative for further details and applicable conditions for these standards. Specifications Unit type Name Communications functions CompoBus/S Master Unit CJ1 Special I/O Units No. of I/O points Max. Units mountable per CPU Unit No. of unit numbers allocated Current consumption (A) 5V 24 V 0.15 - Model Standards CJ1W-SRM21 UC1, N, L, CE, 256 max. (128 inputs and 128 outputs) Remote I/O communications 40 1 or 2 (variable) 128 max. (64 inputs and 64 outputs) Note: This unit cannot be used with the Machine Automation Controller NJ-series. Specifications I/O points 256 (128 inputs and 128 outputs) or 128 (64 inputs and 64 outputs) (Switch-selectable) Applicable PLC models CJ-series PLCs Unit type Special I/O Unit Allocated words * For 256 I/O: 20 words (8 for inputs, 8 for outputs, 4 for status) For 128 I/O: 10 words (4 for inputs, 4 for outputs, 2 for status) No. of mountable Master Units 40 Node address 8 addresses per node No. of connectable Slaves 32 Status information Communications Error Flags, Participation Flags * Uses Special I/O Unit Area (in CIO Area). 2 CJ1W-SRM21 Part Names and Functions SRM21 Indicators Indicates the operating status of the Master Unit and the status of communications with the Slaves. RUN ERH ERC SD RD 901 456 23 MACH No. 1 x10 78 901 456 23 78 1 2 3 4 x100 REGS ESTP DR NODE ON BS+ Rotary Switches Used to set the Master Unit's Special I/O Unit number at the CPU Unit as a 2-digit decimal number. The top switch is used to set the ten's digit and the bottom switch is used to set the one's digit. DIP Switch These pins have the following functions: Pin 1: Usable node number setting Pin 2: Communications mode Pin 3: Communications stop mode Pin 4: Slave registration function BDH BDL BS- Communications Connector Used to connect the Slave's communications power supply and communications cables. When the communications power supply is not supplied to the Slaves from communications cable, connect the communications cable BD H and BD L signal lines only. BS+ BS- Dimensions (Unit: mm) 80 (When provided connector is connected.) 65 2.7 20 SRM21 RUN ERH ERC SD RD 901 456 23 MACH No. 1 x10 78 901 456 23 1 2 3 4 78 90 x100 REGS ESTP DR NODE ON BS+ BDH BDL BS- BS+ 2.7 BS- Refer to the CJ-series Operation Manual for details on installing the CJ1W-SRM21 when it is connected in a CJ-series CPU Rack or Expansion Rack. Related Manual Cat. No. Manual Name W266 CompoBus/S Operation Manual W318 CompoBus/S SRM1 Master Control Units Operation Manual W377 CPM2C-S Programmable Controllers Operation Manual W352 CPM2A I/O Link Units Operation Manual W356 CPM2C I/O Link Units Operation Manual Note: Production will be discontinued in March 2015. 3 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron's exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron's sole obligation hereunder shall be, at Omron's election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron's analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer's application or use of the Product. At Buyer's request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer's application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user's programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron's test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron's Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron's representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2016.9 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2016 All Right Reserved.