SM16LC03C-6 thru 8700 E. Thomas Road Scottsdale, AZ 85251 Tel: (480) 941-6300 Fax: (480) 947-1503 SM16LC24C-6 TVSarray Series DESCRIPTION (300 watt) This 16 pin 6 line Low Capacitance Bidirectional array is designed for use in applications where protection is required at the board level from voltage transients caused by electrostatic discharge (ESD) as defined in IEC 1000-4-2, electrical fast transients (EFT) per IEC 1000-4-4 and effects of secondary lighting. These TRANSIENT VOLTAGE SUPPRESSOR (TVS) Diode Arrays have a peak power of 300 watts for an 8/20 sec pulse and are designed to protect 3.0/3.3 volt components such as DRAM's, SRAM's, CMOS, HCMOS, HSIC, and low voltage interfaces up to 24 volts. FEATURES MECHANICAL * * * * * * * * Protects 3.0/3.3 up through 24V Components Protects 6 lines Bi-directional Provides electrically isolated protection SO-16 Packaging Molded SO-16 Surface Mount Weight: 2.5 grams (approximate) Body Marked with Logo, and device number Pin #1 defined by DOT on top of package MAXIMUM RATINGS PACKAGING * * * * * * * Operating Temperatures: -550C to +1500C Storage Temperature: -550C to +1500C Peak Pulse Power: 300 Watts (8/20 sec, Figure 1) Pulse Repetition Rate: <.01% Tape & Reel EIA Standard 481-1-A 13 inch reel 2,500 pieces (OPTIONAL) Carrier tubes 50 pieces per (STANDARD) ELECTRICAL CHARACTERISTICS@ 250C Unless otherwise specified PART NUMBER DEVICE MARKING STAND OFF VOLTAGE VWM BREAKDOWN VOLTAGE VBR @1 mA VOLTS MAX VOLTS MIN CLAMPING VOLTAGE VC @ 1 Amp (FIGURE 2) VOLTS MAX CLAMPING VOLTAGE VC @ 5 Amp (FIGURE 2) VOLTS MAX LEAKAGE CURRENT ID @ VWM CAPACITANCE (f=1 MHz) @0V C TEMPERATURE COEFFICIENT OF VBR aVBR A MAX pF TYP mV/C MAX -3 SM16LC03C-6 MAL 3.3 4 7 9 200 25 SM16LC05C-6 MAM 5.0 6 9.8 11 100 25 1 SM16LC12C-6 MAN 12 13.3 19 24 1 25 8 SM16LC15C-6 MAO 15 16.7 24 30 1 25 11 SM16LC24C-6 MAP 24 26.7 43 55 1 25 28 NOTE: Transient Voltage Suppression (TVS) product is normally selected based on its stand off voltage VWM. Product selected voltage should be equal to or greater than the continuous peak operating voltage of the circuit to be protected. Application: The SM16LCXXC-6 product is designed for transient voltage suppression protection of components at the board level. It is an ideal product to be used for protection of I/O Transceivers. MSC0979.PDF ISO 9001 CERTIFIED REV D 8/25/99 SM16LC03C-6 thru SM16LC24C-6 Ipp -- Peak Pulse Current -- % Ipp WAVE FORMS 100 Peak Value -- Ipp 8 X 20 Waveform 50 Half-Value -- Ipp 2 0 0 10 20 30 t td t -- Time in microsec FIGURE 1 Peak Pulse Power Vs Pulse Time FIGURE 2 Pulse Wave Form MOUNTING PAD SO-16 CIRCUIT DIAGRAM SO-16 PACKAGE A INCHES B G P L C K MSC0979.PDF MIN MAX MIN MAX A 0.358 0.398 9.09 10.10 B 0.150 0.158 3.81 4.01 C 0.053 0.069 1.35 1.75 D 0.011 0.021 0.28 0.53 F 0.016 0.050 0.41 G D J MILLIMETERS DIM 0.050 BSC 1.27 1.27 BSC J 0.006 0.010 0.15 0.25 K 0.004 0.008 0.10 0.20 L 0.189 0.206 4.80 5.23 P 0.228 0.244 5.79 6.19 F ISO 9001 CERTIFIED REV D 8/25/99