ADC081S051
ADC081S051 Single Channel, 200 to 500 ksps, 8-Bit A/D Converter
Literature Number: SNAS309D
ADC081S051
January 13, 2010
Single Channel, 200 to 500 ksps, 8-Bit A/D Converter
General Description
The ADC081S051 is a low-power, single channel CMOS 8-
bit analog-to-digital converter with a high-speed serial inter-
face. Unlike the conventional practice of specifying perfor-
mance at a single sample rate only, the ADC081S051 is fully
specified over a sample rate range of 200 ksps to 500 ksps.
The converter is based on a successive-approximation reg-
ister architecture with an internal track-and-hold circuit.
The output serial data is straight binary, and is compatible with
several standards, such as SPI™, QSPI™, MICROWIRE,
and many common DSP serial interfaces.
The ADC081S051 operates with a single supply that can
range from +2.7V to +5.25V. Normal power consumption us-
ing a +3.6V or +5.25V supply is 1.6 mW and 8.5 mW, respec-
tively. The power-down feature reduces the power consump-
tion to as low as 2.6 µW using a +5.25V supply.
The ADC081S051 is packaged in 6-lead LLP and SOT-23
packages. Operation over the industrial temperature range of
−40°C to +85°C is guaranteed.
Features
Specified over a range of sample rates.
6-lead LLP and SOT-23 packages
Variable power management
Single power supply with 2.7V - 5.25V range
SPI™/QSPI™/MICROWIRE/DSP compatible
Key Specifications
DNL +0.06 / -0.045 LSB (typ)
INL +0.06 / -0.05 LSB (typ)
SNR 49.6 dB (typ)
Power Consumption
3.6V Supply 1.6 mW (typ)
5.25V Supply 8.5 mW (typ)
Applications
Portable Systems
Remote Data Acquisition
Instrumentation and Control Systems
Pin-Compatible Alternatives by Resolution and Speed
All devices are fully pin and function compatible.
Resolution Specified for Sample Rate Range of:
50 to 200 ksps 200 to 500 ksps 500 ksps to 1 Msps
12-bit ADC121S021 ADC121S051 ADC121S101
10-bit ADC101S021 ADC101S051 ADC081S101
8-bit ADC081S021 ADC081S051 ADC081S101
Connection Diagram
20145505
Ordering Information
Order Code Temperature Range Description Top Mark
ADC081S051CISD −40°C to +85°C 6-Lead LLP Package X6C
ADC081S051CISDX −40°C to +85°C 6-Lead LLP Package, Tape & Reel X6C
ADC081S051CIMF −40°C to +85°C 6-Lead SOT-23 Package X15C
ADC081S051CIMFX −40°C to +85°C 6-Lead SOT-23 Package, Tape & Reel X15C
ADC081S051EVAL SOT-23 Evaluation Board
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 2010 National Semiconductor Corporation 201455 www.national.com
ADC081S051 Single Channel, 200 to 500 ksps, 8-Bit A/D Converter
Block Diagram
20145507
Pin Descriptions and Equivalent Circuits
Pin No. Symbol Description
ANALOG I/O
3VIN Analog input. This signal can range from 0V to VA.
DIGITAL I/O
4 SCLK Digital clock input. This clock directly controls the conversion and readout processes.
5 SDATA Digital data output. The output samples are clocked out of this pin on falling edges of the SCLK pin.
6 CS Chip select. On the falling edge of CS, a conversion process begins.
POWER SUPPLY
1VA
Positive supply pin. This pin should be connected to a quiet +2.7V to +5.25V source and bypassed to
GND with a 1 µF capacitor and a 0.1 µF monolithic capacitor located within 1 cm of the power pin.
2 GND The ground return for the supply and signals.
PAD GND For package suffix CISD(X) only, it is recommended that the center pad should be connected to ground.
www.national.com 2
ADC081S051
Absolute Maximum Ratings (Note 1, Note
2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Analog Supply Voltage VA−0.3V to 6.5V
Voltage on Any Analog Pin to GND −0.3V to (VA +0.3V)
Voltage on Any Digital Pin to GND −0.3V to 6.5V
Input Current at Any Pin (Note 3) ±10 mA
Package Input Current (Note 3) ±20 mA
Power Consumption at TA = 25°C See (Note 4)
ESD Susceptibility (Note 5)
Human Body Model
Machine Model
3500V
300V
Junction Temperature +150°C
Storage Temperature −65°C to +150°C
Operating Ratings (Note 1, Note 2)
Operating Temperature Range −40°C TA +85°C
VA Supply Voltage +2.7V to +5.25V
Digital Input Pins Voltage Range
(regardless of supply voltage)
−0.3V to 5.25V
Analog Input Pins Voltage Range 0V to VA
Clock Frequency 25 kHz to 20 MHz
Sample Rate up to 1Msps
Package Thermal Resistance
Package θJA
6-lead LLP 94°C / W
6-lead SOT-23 265°C / W
Soldering process must comply with National
Semiconductor's Reflow Temperature Profile specifications.
Refer to www.national.com/packaging. (Note 6)
ADC081S051 Converter Electrical Characteristics (Note 7, Note 9)
The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 4 MHz to 10 MHz, fSAMPLE = 200 ksps to 500 ksps,
CL = 15 pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Symbol Parameter Conditions Typical Limits
(Note 9)Units
STATIC CONVERTER CHARACTERISTICS
Resolution with No Missing Codes 8Bits
INL Integral Non-Linearity
VA = +2.7V to +3.6V ±0.04 ±0.3 LSB (max)
VA = +4.75V to +5.25V +0.06 ±0.3 LSB (max)
−0.045 LSB (min)
DNL Differential Non-Linearity
VA = +2.7V to +3.6V ±0.05 ±0.2 LSB (max)
VA = +4.75V to +5.25V +0.06 ±0.2 LSB (max)
−0.05 LSB (min)
VOFF Offset Error VA = +2.7V to +3.6V −0.01 ±0.2 LSB (max)
VA = +4.75V to +5.25V +0.04 ±0.2 LSB (max)
GE Gain Error VA = +2.7V to +3.6V +0.01 ±0.4 LSB (max)
VA = +4.75V to +5.25V −0.075 ±0.4 LSB (max)
TUE Total Unadjusted Error
VA = +2.7V to +3.6V +0.04 ±0.3 LSB (max)
−0.045 LSB (min)
VA = +4.75V to +5.25V +0.07 ±0.3 LSB (max)
−0.055 LSB (min)
DYNAMIC CONVERTER CHARACTERISTICS
SINAD Signal-to-Noise Plus Distortion Ratio VA = +2.7 to 5.25V
fIN = 100 kHz, −0.02 dBFS 49.5 49 dB (min)
SNR Signal-to-Noise Ratio VA = +2.7 to 5.25V
fIN = 100 kHz, −0.02 dBFS 49.6 49 dB (min)
THD Total Harmonic Distortion VA = +2.7 to 5.25V
fIN = 100 kHz, −0.02 dBFS −77 −65 dB (max)
SFDR Spurious-Free Dynamic Range VA = +2.7 to 5.25V
fIN = 100 kHz, −0.02 dBFS 68 65 dB (min)
ENOB Effective Number of Bits VA = +2.7 to 5.25V
fIN = 100 kHz, −0.02 dBFS 7.9 7.8 Bits (min)
3 www.national.com
ADC081S051
Symbol Parameter Conditions Typical Limits
(Note 9)Units
IMD
Intermodulation Distortion, Second
Order Terms
VA = +5.25V
fa = 103.5 kHz, fb = 113.5 kHz −83 dB
Intermodulation Distortion, Third Order
Terms
VA = +5.25V
fa = 103.5 kHz, fb = 113.5 kHz −82 dB
FPBW -3 dB Full Power Bandwidth VA = +5V 11 MHz
VA = +3V 8 MHz
ANALOG INPUT CHARACTERISTICS
VIN Input Range 0 to VAV
IDCL DC Leakage Current ±1 µA (max)
CINA Input Capacitance Track Mode 30 pF
Hold Mode 4 pF
DIGITAL INPUT CHARACTERISTICS
VIH Input High Voltage VA = +5.25V 2.4 V (min)
VA = +3.6V 2.1 V (min)
VIL Input Low Voltage VA = +5.25V 0.8 V (max)
VA = +3.6V 0.4 V (max)
IIN Input Current VIN = 0V or VA±0.1 ±1 µA (max)
CIND Digital Input Capacitance 2 4pF (max)
DIGITAL OUTPUT CHARACTERISTICS
VOH Output High Voltage ISOURCE = 200 µA VA − 0.07 VA − 0.2 V (min)
ISOURCE = 1 mA VA − 0.1 V
VOL Output Low Voltage ISINK = 200 µA 0.03 0.4 V (max)
ISINK = 1 mA 0.1 V
IOZH, IOZL TRI-STATE® Leakage Current ±0.1 ±10 µA (max)
COUT TRI-STATE® Output Capacitance 2 4pF (max)
Output Coding Straight (Natural) Binary
POWER SUPPLY CHARACTERISTICS
VASupply Voltage 2.7 V (min)
5.25 V (max)
IA
Supply Current, Normal Mode
(Operational, CS low)
VA = +5.25V,
fSAMPLE = 200 ksps 1.61 2.4 mA (max)
VA = +3.6V,
fSAMPLE = 200 ksps 0.43 1.0 mA (max)
Supply Current, Shutdown (CS high)
fSCLK= 0 MHz, VA = +5.25V
fSAMPLE = 0 ksps 500 nA
VA = +5.25V, fSCLK = 10 MHz,
fSAMPLE = 0 ksps 60 µA
PD
Power Consumption, Normal Mode
(Operational, CS low)
VA = +5.25V 8.5 12.6 mW (max)
VA = +3.6V 1.6 3.6 mW (max)
Power Consumption, Shutdown (CS
high)
fSCLK = 0 MHz, VA = +5.25V
fSAMPLE = 0 ksps 2.6 µW
VA = +5.25V, fSCLK = 10 MHz,
fSAMPLE = 0 ksps 315 µW
AC ELECTRICAL CHARACTERISTICS
fSCLK Clock Frequency (Note 8) 4MHz (min)
10 MHz (max)
fSSample Rate (Note 8)50 200 ksps (min)
500 ksps (max)
www.national.com 4
ADC081S051
Symbol Parameter Conditions Typical Limits
(Note 9)Units
DC SCLK Duty Cycle fSCLK = 10 MHz 50 40 % (min)
60 % (max)
tACQ Minimum Time Required for Acquisition 350 ns (max)
tQUIET (Note 10) 50 ns (min)
tAD Aperture Delay 3 ns
tAJ Aperture Jitter 30 ps
ADC081S051 Timing Specifications
The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 4 MHz to 10 MHz, CL = 25 pF,
fSAMPLE = 200 ksps to 500 ksps, Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.
Symbol Parameter Conditions Typical Limits Units
tCS Minimum CS Pulse Width 10 ns (min)
tSU CS to SCLK Setup Time 10 ns (min)
tEN
Delay from CS Until SDATA TRI-STATE® Disabled
(Note 11) 20 ns (max)
tACC Data Access Time after SCLK Falling Edge (Note 12)VA = +2.7V to +3.6V 40 ns (max)
VA = +4.75V to +5.25V 20 ns (max)
tCL SCLK Low Pulse Width 0.4 x tSCLK ns (min)
tCH SCLK High Pulse Width 0.4 x tSCLK ns (min)
tHSCLK to Data Valid Hold Time VA = +2.7V to +3.6V 7ns (min)
VA = +4.75V to +5.25V 5ns (min)
tDIS
SCLK Falling Edge to SDATA High Impedance (Note
13)
VA = +2.7V to +3.6V 25 ns (max)
6ns (min)
VA = +4.75V to +5.25V 25 ns (max)
5ns (min)
tPOWER-UP Power-Up Time from Full Power-Down 1 µs
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: All voltages are measured with respect to GND = 0V, unless otherwise specified.
Note 3: When the input voltage at any pin exceeds the power supply (that is, VIN < GND or VIN > VA), the current at that pin should be limited to 10 mA. The 20
mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two. The Absolute
Maximum Rating specification does not apply to the VA pin. The current into the VA pin is limited by the Analog Supply Voltage specification.
Note 4: The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by TJmax, the
junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA)/θJA. The values
for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven
beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.
Note 5: Human body model is 100 pF capacitor discharged through a 1.5 k resistor. Machine model is 220 pF discharged through zero ohms
Note 6: Reflow temperature profiles are different for lead-free and non-lead-free packages.
Note 7: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Note 8: This is the frequency range over which the electrical performance is guaranteed. The device is functional over a wider range which is specified under
Operating Ratings.
Note 9: Data sheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 10: Minimum Quiet Time required by Bus relinquish and start of the next conversion.
Note 11: Measured with the timing test circuit shown in Figure 1 and defined as the time taken by the output signal to cross 1.0V.
Note 12: Measured with the timing test circuit shown in Figure 1 and defined as the time taken by the output signal to cross 1.0V or 2.0V.
Note 13: tDIS is derived from the time taken by the output to change by 0.5V with the timing test circuit shown in Figure 1. The measured number is then adjusted
to remove the effects of charging or discharging the load capacitance. This means that tDIS is the true bus relinquish time, independent of the bus loading.
5 www.national.com
ADC081S051
Timing Diagrams
20145508
FIGURE 1. Timing Test Circuit
20145506
FIGURE 2. ADC081S051 Serial Timing Diagram
www.national.com 6
ADC081S051
Specification Definitions
ACQUISITION TIME is the time required to acquire the input
voltage. That is, it is time required for the hold capacitor to
charge up to the input voltage. Acquisition time is measured
backwards from the falling edge of CS when the signal is
sampled and the part moves from track to hold. The start of
the time interval that contains TACQ is the 13th rising edge of
SCLK of the previous conversion when the part moves from
hold to track. The user must ensure that the time between the
13th rising edge of SCLK and the falling edge of the next
CS is not less than TACQ to meet performance specifications.
APERTURE DELAY is the time after the falling edge of CS
when the input signal is acquired or held for conversion.
APERTURE JITTER (APERTURE UNCERTAINTY) is the
variation in aperture delay from sample to sample. Aperture
jitter manifests itself as noise in the output.
CONVERSION TIME is the time required, after the input volt-
age is acquired, for the ADC to convert the input voltage to a
digital word. This is from the falling edge of CS when the input
signal is sampled to the 16th falling edge of SCLK when the
SDATA output goes into TRI-STATE.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of
the maximum deviation from the ideal step size of 1 LSB.
DUTY CYCLE is the ratio of the time that a repetitive digital
waveform is high to the total time of one period. The specifi-
cation here refers to the SCLK.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE
BITS) is another method of specifying Signal-to-Noise and
Distortion or SINAD. ENOB is defined as
(SINAD − 1.76) / 6.02 and says that the converter is equiva-
lent to a perfect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH is a measure of the frequency
at which the reconstructed output fundamental drops 3 dB
below its low frequency value for a full scale input.
GAIN ERROR is the deviation of the last code transition
(111...110) to (111...111) from the ideal (VREF − 1 LSB), after
adjusting for offset error.
INTEGRAL NON-LINEARITY (INL) is a measure of the de-
viation of each individual code from a line drawn from negative
full scale (½ LSB below the first code transition) through pos-
itive full scale (½ LSB above the last code transition). The
deviation of any given code from this straight line is measured
from the center of that code value.
INTERMODULATION DISTORTION (IMD) is the creation of
additional spectral components as a result of two sinusoidal
frequencies being applied to the ADC input at the same time.
It is defined as the ratio of the power in the second and third
order intermodulation products to the sum of the power in both
of the original frequencies. IMD is usually expressed in dB.
MISSING CODES are those output codes that will never ap-
pear at the ADC outputs. The ADC081S051 is guaranteed not
to have any missing codes.
OFFSET ERROR is the deviation of the first code transition
(000...000) to (000...001) from the ideal (i.e. GND + 1 LSB).
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in
dB, of the rms value of the input signal to the rms value of the
sum of all other spectral components below one-half the sam-
pling frequency, not including harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/N+D or
SINAD) Is the ratio, expressed in dB, of the rms value of the
input signal to the rms value of all of the other spectral com-
ponents below half the clock frequency, including harmonics
but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the differ-
ence, expressed in dB, between the desired signal amplitude
to the amplitude of the peak spurious spectral component,
where a spurious spectral component is any signal present in
the output spectrum that is not present at the input and may
or may not be a harmonic.
TOTAL HARMONIC DISTORTION (THD) is the ratio, ex-
pressed in dB or dBc, of the rms total of the first five harmonic
components at the output to the rms level of the input signal
frequency as seen at the output. THD is calculated as
where Af1 is the RMS power of the input frequency at the out-
put and Af2 through Af6 are the RMS power in the first 5
harmonic frequencies.
THROUGHPUT TIME is the minimum time required between
the start of two successive conversion. It is the acquisition
time plus the conversion time.
TOTAL UNADJUSTED ERROR is the worst deviation found
from the ideal transfer function. As such, it is a comprehensive
specification which includes full scale error, linearity error,
and offset error.
7 www.national.com
ADC081S051
Typical Performance Characteristics TA = +25°C, fSAMPLE = 200 ksps to 500 ksps,
fSCLK = 4 MHz to 10 MHz, fIN = 100 kHz unless otherwise stated.
DNL
fSCLK = 4 MHz
20145520
INL
fSCLK = 4 MHz
20145521
DNL
fSCLK = 10 MHz
20145560
INL
fSCLK = 10 MHz
20145561
DNL vs. Clock Frequency
20145565
INL vs. Clock Frequency
20145566
www.national.com 8
ADC081S051
Total Unadjusted Error vs. Clock Frequency
20145567
SNR vs. Clock Frequency
20145563
SINAD vs. Clock Frequency
20145564
THD vs. Clock Frequency
20145568
SFDR vs.Clock Frequency
20145572
Spectral Response, VA = 5V, fSCLK = 4 MHz
20145569
9 www.national.com
ADC081S051
Spectral Response, VA = 5V, fSCLK = 10 MHz
20145570
Power Consumption vs. Throughput,
fSCLK = 10 MHz
20145555
Applications Information
1.0 ADC081S051 OPERATION
The ADC081S051 is a successive-approximation analog-to-
digital converter designed around a charge-redistribution dig-
ital-to-analog converter core. Simplified schematics of the
ADC081S051 in both track and hold modes are shown in
Figure 3 and Figure 4, respectively. In Figure 3, the device is
in track mode: switch SW1 connects the sampling capacitor
to the input and SW2 balances the comparator inputs. The
device is in this state until CS is brought low, at which point
the device moves to hold mode.
Figure 4 shows the device in hold mode: switch SW1 con-
nects the sampling capacitor to ground, maintaining the sam-
pled voltage, and switch SW2 unbalances the comparator.
The control logic then instructs the charge-redistribution DAC
to add or subtract fixed amounts of charge from the sampling
capacitor until the comparator is balanced. When the com-
parator is balanced, the digital word supplied to the DAC is
the digital representation of the analog input voltage. The de-
vice moves from hold mode to track mode on the 13th rising
edge of SCLK.
20145509
FIGURE 3. ADC081S051 in Track Mode
20145510
FIGURE 4. ADC081S051 in Hold Mode
www.national.com 10
ADC081S051
2.0 USING THE ADC081S051
The serial interface timing diagram for the ADC is shown in
Figure 2. CS is chip select, which initiates conversions on the
ADC and frames the serial data transfers. SCLK (serial clock)
controls both the conversion process and the timing of serial
data. SDATA is the serial data out pin, where a conversion
result is found as a serial data stream.
Basic operation of the ADC begins with CS going low, which
initiates a conversion process and data transfer. Subsequent
rising and falling edges of SCLK will be labelled with reference
to the falling edge of CS; for example, "the third falling edge
of SCLK" shall refer to the third falling edge of SCLK after
CS goes low.
At the fall of CS, the SDATA pin comes out of TRI-STATE and
the converter moves from track mode to hold mode. The input
signal is sampled and held for conversion on the falling edge
of CS. The converter moves from hold mode to track mode
on the 13th rising edge of SCLK (see Figure 2). It is at this
point that the interval for the TACQ specification begins. In the
worst case, 350ns must pass between the 13th rising edge
and the next falling edge of SCLK. The SDATA pin will be
placed back into TRI-STATE after the 16th falling edge of
SCLK, or at the rising edge of CS, whichever occurs first. After
a conversion is completed, the quiet time (tQUIET) must be
satisfied before bringing CS low again to begin another con-
version.
Sixteen SCLK cycles are required to read a complete sample
from the ADC. The sample bits (including leading or trailing
zeroes) are clocked out on falling edges of SCLK, and are
intended to be clocked in by a receiver on subsequent rising
edges of SCLK. The ADC will produce three leading zero bits
on SDATA, followed by eight data bits, most significant first.
After the data bits, the ADC will clock out four trailing zeros.
If CS goes low before the rising edge of SCLK, an additional
(fourth) zero bit may be captured by the next falling edge of
SCLK.
2.1 Determining Throughput
Throughput depends on the frequency of SCLK and how
much time is allowed to elapse between the end of one con-
version and the start of another. At the maximum specified
SCLK frequency, the maximum guaranteed throughput is ob-
tained by using a 20 SCLK frame. As shown in Figure 2, the
minimum allowed time between CS falling edges is deter-
mined by 1) 12.5 SCLKs for Hold mode, 2) the larger of two
quantities: either the minimum required time for Track mode
(tACQ) or 2.5 SCLKs to finish reading the result and 3) 0, 1/2
or 1 SCLK padding to ensure an even number of SCLK cycles
so there is a falling SCLK edge when CS next falls. For ex-
ample, at the fastest rate for this family of parts, SCLK is
20MHz and 2.5 SCLKs are 125ns, so the minimum time be-
tween CS falling edges is calculated by
12.5*50ns + 350ns + 0.5*50ns = 1000ns
(12.5 SCLKs + tACQ + 1/2 SCLK) which corresponds to a
maximum throughput of 1MSPS. At the slowest rate for this
family, SCLK is 1MHz. Using a 20 cycle conversion frame as
shown in Figure 2 yields a 20μs time between CS falling
edges for a throughput of 50KSPS. It is possible, however, to
use fewer than 20 clock cycles provided the timing parame-
ters are met. With a 1MHz SCLK, there are 2500ns in 2.5
SCLK cycles, which is greater than tACQ. After the last data bit
has come out, the clock will need one full cycle to return to a
falling edge. Thus the total time between falling edges of CS
is 12.5*1μs +2.5*1μs +1*1μs=16μs which is a throughput of
62.5KSPS.
3.0 ADC081S051 TRANSFER FUNCTION
The output format of the ADC is straight binary. Code transi-
tions occur midway between successive integer LSB values.
The LSB width for the ADC is VA/256. The ideal transfer char-
acteristic is shown in Figure 5. The transition from an output
code of 0000 0000 to a code of 0000 0001 is at 1/2 LSB, or a
voltage of VA/512. Other code transitions occur at steps of one
LSB.
20145511
FIGURE 5. Ideal Transfer Characteristic
11 www.national.com
ADC081S051
4.0 TYPICAL APPLICATION CIRCUIT
A typical application of the ADC is shown in Figure 6. Power
is provided in this example by the National Semiconductor
LP2950 low-dropout voltage regulator, available in a variety
of fixed and adjustable output voltages. The power supply pin
is bypassed with a capacitor network located close to the
ADC. Because the reference for the ADC is the supply volt-
age, any noise on the supply will degrade device noise per-
formance. To keep noise off the supply, use a dedicated linear
regulator for this device, or provide sufficient decoupling from
other circuitry to keep noise off the ADC supply pin. Because
of the ADC's low power requirements, it is also possible to
use a precision reference as a power supply to maximize per-
formance. The three-wire interface is shown connected to a
microprocessor or DSP.
20145513
FIGURE 6. Typical Application Circuit
5.0 ANALOG INPUTS
An equivalent circuit of the ADC's input is shown in Figure 7.
Diodes D1 and D2 provide ESD protection for the analog in-
puts. At no time should the analog input go beyond (VA + 300
mV) or (GND − 300 mV), as these ESD diodes will begin to
conduct, which could result in erratic operation. For this rea-
son, the ESD diodes should not be used to clamp the input
signal.
The capacitor C1 in Figure 7 has a typical value of 4 pF, and
is mainly the package pin capacitance. Resistor R1 is the on
resistance of the track / hold switch, and is typically 500.
Capacitor C2 is the ADC sampling capacitor and is typically
26 pF. The ADC will deliver best performance when driven by
a low-impedance source to eliminate distortion caused by the
charging of the sampling capacitance. This is especially im-
portant when using the ADC to sample AC signals. Also
important when sampling dynamic signals is an anti-aliasing
filter.
20145514
FIGURE 7. Equivalent Input Circuit
6.0 DIGITAL INPUTS AND OUTPUTS
The ADC digital inputs (SCLK and CS) are not limited by the
same maximum ratings as the analog inputs. The digital input
pins are instead limited to +5.25V with respect to GND, re-
gardless of VA, the supply voltage. This allows the ADC to be
interfaced with a wide range of logic levels, independent of
the supply voltage.
7.0 MODES OF OPERATION
The ADC has two possible modes of operation: normal mode,
and shutdown mode. The ADC enters normal mode (and a
conversion process is begun) when CS is pulled low. The de-
vice will enter shutdown mode if CS is pulled high before the
tenth falling edge of SCLK after CS is pulled low, or will stay
in normal mode if CS remains low. Once in shutdown mode,
the device will stay there until CS is brought low again. By
varying the ratio of time spent in the normal and shutdown
modes, a system may trade-off throughput for power con-
sumption, with a sample rate as low as zero.
7.1 Normal Mode
The fastest possible throughput is obtained by leaving the
ADC in normal mode at all times, so there are no power-up
delays. To keep the device in normal mode continuously,
CS must be kept low until after the 10th falling edge of SCLK
after the start of a conversion (remember that a conversion is
initiated by bringing CS low).
If CS is brought high after the 10th falling edge, but before the
16th falling edge, the device will remain in normal mode, but
the current conversion will be aborted, and SDATA will return
to TRI-STATE (truncating the output word).
Sixteen SCLK cycles are required to read all of a conversion
word from the device. After sixteen SCLK cycles have
elapsed, CS may be idled either high or low until the next
conversion. If CS is idled low, it must be brought high again
before the start of the next conversion, which begins when
CS is again brought low.
After sixteen SCLK cycles, SDATA returns to TRI-STATE.
Another conversion may be started, after tQUIET has elapsed,
by bringing CS low again.
www.national.com 12
ADC081S051
7.2 Shutdown Mode
Shutdown mode is appropriate for applications that either do
not sample continuously, or it is acceptable to trade through-
put for power consumption. When the ADC is in shutdown
mode, all of the analog circuitry is turned off.
To enter shutdown mode, a conversion must be interrupted
by bringing CS high anytime between the second and tenth
falling edges of SCLK, as shown in Figure 8. Once CS has
been brought high in this manner, the device will enter shut-
down mode, the current conversion will be aborted and SDA-
TA will enter TRI-STATE. If CS is brought high before the
second falling edge of SCLK, the device will not change
mode; this is to avoid accidentally changing mode as a result
of noise on the CS line.
20145516
FIGURE 8. Entering Shutdown Mode
20145517
FIGURE 9. Entering Normal Mode
To exit shutdown mode, bring CS back low. Upon bringing
CS low, the ADC will begin powering up (power-up time is
specified in the Timing Specifications table). This microsec-
ond of power-up delay results in the first conversion result
being unusable. The second conversion performed after pow-
er-up, however, is valid, as shown in Figure 9.
If CS is brought back high before the 10th falling edge of
SCLK, the device will return to shutdown mode. This is done
to avoid accidentally entering normal mode as a result of
noise on the CS line. To exit shutdown mode and remain in
normal mode, CS must be kept low until after the 10th falling
edge of SCLK. The ADC will be fully powered-up after 16
SCLK cycles.
8.0 POWER MANAGEMENT
The ADC takes time to power-up, either after first applying
VA, or after returning to normal mode from shutdown mode.
This corresponds to one "dummy" conversion for any SCLK
frequency within the specifications in this document. After this
first dummy conversion, the ADC will perform conversions
properly. Note that the tQUIET time must still be included be-
tween the first dummy conversion and the second valid con-
version.
When the VA supply is first applied, the ADC may power up
in either of the two modes: normal or shutdown. As such, one
dummy conversion should be performed after start-up, as de-
scribed in the previous paragraph. The part may then be
placed into either normal mode or the shutdown mode, as
described in Sections 7.1 and 7.2.
When the ADC is operated continuously in normal mode, the
maximum guaranteed throughput is fSCLK / 20 at the maximum
specified fSCLK . Throughput may be traded for power con-
sumption by running fSCLK at its maximum specified rate and
performing fewer conversions per unit time, raising the ADC
CS line after the 10th and before the 15th fall of SCLK of each
conversion. A plot of typical power consumption versus
throughput is shown in the Typical Performance Curves sec-
tion. To calculate the power consumption for a given through-
put, multiply the fraction of time spent in the normal mode by
the normal mode power consumption and add the fraction of
time spent in shutdown mode multiplied by the shutdown
mode power consumption. Note that the curve of power con-
sumption vs. throughput is essentially linear. This is because
the power consumption in the shutdown mode is so small that
it can be ignored for all practical purposes.
9.0 POWER SUPPLY NOISE CONSIDERATIONS
The charging of any output load capacitance requires current
from the power supply, VA. The current pulses required from
the supply to charge the output capacitance will cause voltage
variations on the supply. If these variations are large enough,
they could degrade SNR and SINAD performance of the ADC.
Furthermore, discharging the output capacitance when the
digital output goes from a logic high to a logic low will dump
current into the die substrate, which is resistive. Load dis-
charge currents will cause "ground bounce" noise in the sub-
strate that will degrade noise performance if that current is
large enough. The larger the output capacitance, the more
current flows through the die substrate and the greater is the
noise coupled into the analog channel, degrading noise per-
formance.
13 www.national.com
ADC081S051
To keep noise out of the power supply, keep the output load
capacitance as small as practical. It is good practice to use a
100 series resistor at the ADC output, located as close to
the ADC output pin as practical. This will limit the charge and
discharge current of the output capacitance and maintain
noise performance.
www.national.com 14
ADC081S051
Physical Dimensions inches (millimeters) unless otherwise noted
6-Lead LLP
Order Number ADC081S051CISD or ADC081S051CISDX
NS Package Number SDB06A
6-Lead SOT-23
Order Number ADC081S051CIMF, ADC081S051CIMFX
NS Package Number MF06A
15 www.national.com
ADC081S051
Notes
ADC081S051 Single Channel, 200 to 500 ksps, 8-Bit A/D Converter
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
www.national.com
Products Design Support
Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench
Audio www.national.com/audio App Notes www.national.com/appnotes
Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns
Data Converters www.national.com/adc Samples www.national.com/samples
Interface www.national.com/interface Eval Boards www.national.com/evalboards
LVDS www.national.com/lvds Packaging www.national.com/packaging
Power Management www.national.com/power Green Compliance www.national.com/quality/green
Switching Regulators www.national.com/switchers Distributors www.national.com/contacts
LDOs www.national.com/ldo Quality and Reliability www.national.com/quality
LED Lighting www.national.com/led Feedback/Support www.national.com/feedback
Voltage References www.national.com/vref Design Made Easy www.national.com/easy
PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions
Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero
Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic
PLL/VCO www.national.com/wireless PowerWise® Design
University
www.national.com/training
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2010 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Technical
Support Center
Email: support@nsc.com
Tel: 1-800-272-9959
National Semiconductor Europe
Technical Support Center
Email: europe.support@nsc.com
National Semiconductor Asia
Pacific Technical Support Center
Email: ap.support@nsc.com
National Semiconductor Japan
Technical Support Center
Email: jpn.feedback@nsc.com
www.national.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TIs terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TIs standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Communications and Telecom www.ti.com/communications
Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers
Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps
DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy
DSP dsp.ti.com Industrial www.ti.com/industrial
Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical
Interface interface.ti.com Security www.ti.com/security
Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2011, Texas Instruments Incorporated