Instruction Sheet Dual In-Line Package (DIP) 408-7779 Programming Switches (was IS 7779) (7000 and 7100 Series) 1. INTRODUCTION 04 MAY 06 NOTE This Instruction Sheet covers the installation of the 7000 and 7100 Series DIP Programming Switches shown in Figures 1 and 2. Read this document before performing any application using these products. Rev A All dimensions are in metric units [with inches in brackets]. Figures and illustrations are for reference only, and are not drawn to scale. Reason for revision may be found in Section 5, REVISION SUMMARY. Low-Profile Switch Position Number (Flush Rocker) Tape Standard Profile Switch DIP Socket (Raised Rocker) Rocker PC Board Low-Profile Switch with Side-Actuated Switch (Side Rocker) Tape Strippable Transparent Application for Removal Switch Seal Application for Soldered Switch SINGLE POLE SINGLE THROW (SPST) SERIES AND NUMBER OF COLOR POSITIONS 7000 Black (Refer to Product Spec 108-7519) 7100 Blue (Refer to Product Spec 108-7532) RAISED ROCKER SIDE ROCKER FLUSH ROCKER (STANDARD-PROFILE) (SIDE-ACTUATED) (LOW-PROFILE) Unsealed Econ. Seal Unsealed Econ. Seal Unsealed Econ. Seal 2 2-435166-9 --- 1-435802-0 --- --- 3-435626-6 3 3-435166-0 --- 435802-2 --- --- 3-435626-7 4 435166-2 4-435166-9 435802-3 1-435802-5 435626-1 3-435626-8 5 435166-3 5-435166-0 435802-4 1-435802-6 435626-2 3-435626-9 6 435166-4 5-435166-1 435802-5 1-435802-7 --- 4-435626-0 7 435166-1 5-435166-2 435802-6 1-435802-8 --- 4-435626-1 8 435166-5 5-435166-3 435802-1 435802-9 435626-5 4-435626-2 9 435166-6 5-435166-4 435802-7 1-435802-9 --- 4-435626-3 10 435166-7 5-435166-5 435802-8 2-435802-0 --- 4-435626-4 11 --- --- --- 2-435802-1 --- --- 12 3-435166-2 5-435166-7 1-435802-2 2-435802-2 --- 4-435626-6 2 2-435640-9 --- --- --- 435668-1 2-435668-6 3 3-435640-0 --- --- --- 435668-2 3-435668-3 4 435640-2 3-435640-5 --- --- 435668-3 3-435668-4 5 435640-3 3-435640-6 --- --- 435668-4 3-435668-5 6 435640-4 3-435640-7 --- --- 435668-5 2-435668-5 7 435640-1 3-435640-8 --- --- 435668-6 2-435668-7 8 435640-5 3-435640-9 --- --- 435668-7 2-435668-8 9 435640-6 4-435640-0 --- --- --- 2-435668-9 10 435640-7 4-435640-1 --- --- 435668-9 3-435668-0 11 --- --- --- --- --- 3-435668-1 12 3-435640-2 4-435640-3 --- --- 1-435668-1 3-435668-2 NOTE: Contact Tyco Electronics for RoHS compliant part numbers which may be associated with this document. Figure 1 E 2006 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved Tyco is a trademark. TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, *Trademark Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 4 LOC B 408-7779 DIP Switches (7000 and 7100 Series) 2. INTRODUCTION 3. SWITCH INSTALLATION The SPST and MPMT switches are available in 2 through 12 positions. They can be used in DIP sockets with in-row contact centerline spacing of 25.4 [.100] and row-to-row contact centerline spacing of 7.62 [.300], or they can be soldered directly to the printed circuit (pc) board. There are standard-profile, side-actuated, and low- profile SPST switches. The standard-profile switches have raised rockers, and are available unsealed, or sealed with an economy or premium masking material. The side-actuated switches have rockers on the side rather than on the top, and are available unsealed, or sealed with an economy or premium masking material. The low-profile switches have flush rockers, and are available unsealed, or sealed with an economy clear tape, or sealed with a premium masking material. Determine the number of switch positions required for your application. Determine whether the switch will be soldered directly to the pc board ( a sealed switch will be required), or whether the switch is to be installed in a socket (an unsealed switch can be used). Refer to the tables in Figures 1 or 2 for assistance in selecting a switch. 3.1. DIP Socket Installation 1. Secure DIP socket to pc board according to instructions packaged with socket. 2. Start one row of contact leads into one row of contact cavities in socket, then rotate switch until it is parallel with socket. 3. Gripping ends of switch, push switch into socket until it is bottomed There are standard-profile and side-actuated MPMT switches. The standard-profile MPMT comes in both Single-Pole Double-Throw (SPDT) and Double-Pole Double-Throw (DPDT) make-before-break switches and are available with a low-profile and extended lever actuator. The side-actuated MPMT is available in SPST only at this time. All of these switches are available in the unsealed version only. 4. Determine which of the circuits are to be closed, then depress the applicable rockers to the ON position. 5. If installing a protective dust cover, determine the number of switch positions and refer to Customer Drawing 435238 to select the applicable cover. Check to be sure there are no obstructions on the switch rockers or in the protective cover, then slide the cover over the rockers until the cover latches engage the housing. See Figure 3. The unsealed switches are designed for socket applications and the sealed are designed for soldering applications directly to the pc board. The sealants prevent flux and other contaminants from entering the switch during soldering and cleaning. MULTIPLE THROW MULTIPLE THROW SWITCHES (MPMT) SERIES AND NUMBER OF CO O COLOR SWITCHES S C S DOUBLE POLE SINGLE THROW SINGLE POLE DOUBLE THROW Low Profile Actuator Extended Actuator Low Profile Actuator Extended Actuator 1 435469-9 2-435469-1 435470-7 2-435470-1 2 --- 2-435469-2 435470-1 2-435470-2 3 435469-2 2-435469-3 435470-2 --- 4 435469-3 2-435469-4 435470-3 2-435470-4 5 --- 2-435469-5 435470-4 2-435470-5 6 1-435469-0 2-435469-6 435470-8 2-435470-6 7000 Black (Refer to Product Spec S 108-7519) 108 7519) SERIES AND NUMBER OF CO O COLOR SWITCHES S C S 7000 Black (Refer to Product Spec p 108-7519) FOUR POLE SINGLE THROW DOUBLE POLE DOUBLE THROW Low Profile Actuator Extended Actuator Low Profile Actuator Extended Actuator 1 435469-7 3-435469-1 435470-5 3-435470-1 2 --- 3-435469-2 435470-9 3-435470-2 3 --- --- --- 3-435470-3 Figure 2 2 of 4 Rev A 408-7779 DIP Switches (7000 and 7100 Series) Grip Here Protective Cover Housing Bottomed on PC Board PC Board Clinched Contact Lead (Inward Only) Figure 5 Cover Latch NOTE For pc board soldering and cleaning procedures, and recommended solvents, refer to Tyco Figure 3 Electronics Application Specification 114-1056. 4. SWITCH PROGRAMMING 3.2. PC Board Installation 1. Make a layout on the pc board according to the dimensions shown in Figure 4. After the switch has been inserted into the DIP socket or soldered onto the pc board, proceed as follows: 1. Remove seal from the switches, see Figure 6. 2. Make certain all contact leads have started entry into holes. Grip sides of switch and push switch into pc board until it is bottomed. 3. Hold switch at a slight angle and start one row on contact leads into pc board holes. Do NOT over-insert. Switch should be rotated until second row of contact leads are aligned with opposite row of contact holes. Use Light Pressure Rotate to Align Second to Insert Switch Row - Then Push Down Remove Tape Seal from End Low-Profile Switch on Ends of Switch 7.62 [.300] Ref Remove Seal from Top Masking Material Left to Bottom Right Seal (Diagonal Across the Switch) NOTE: These same procedures 2.54 [.100] Ref apply to socket installation. Figure 4 Standard-Profile or Side-Actuated Switch NOTE To hold switch in place during wave soldering, the four outside contact leads may be clinched Figure 6 inward at 45 . Refer to Figure 5. Rev A 3 of 4 DIP Switches (7000 and 7100 Series) 408-7779 2. Determine which circuits are to be closed, then depress applicable rockers to ON position. Refer to Figure 7. Push Down to ON Position 5. REVISION SUMMARY S Updated document to corporate requirements S General update to format S Deleted old and added new part numbers in the tables in Figures 1 and 2 Figure 7 4 of 4 Rev A