UT54ACS164245S/SE RadHard Schmitt CMOS 16-bit Bidirectional MultiPurpose Transceiver Datasheet December 2004 www.aeroflex.com/radhard LOGIC SYMBOL FEATURES * Voltage translation - 5V bus to 3.3V bus - 3.3V bus to 5V bus * Cold sparing - 1M minimum input impedance power-off OE1 (48) G1 OE2 (25) (1) DIR1 G2 1A1 * 0.6m Commercial RadHard CMOS - Total dose: 100K rad(Si) - Single Event Latchup immune * High speed, low power consumption * Schmitt trigger inputs to filter noisy signals * Available QML Q or V processes * Standard Microcircuit Drawing 5962-98580 * Package: - 48-lead flatpack, 25 mil pitch (.390 x .640) TM 1A2 DIR2 (2) 11 12 (46) (3) (5) (43) 1A4 (41) 1A5 (40) 1A6 (38) 1A7 (37) 1A8 (36) 2A1 (6) 2A2 2A3 The 16-bit wide UT54ACS164245S MultiPurpose transceiver is built using UTMC's Commercial RadHardTM epitaxial CMOS technology and is ideal for space applications. This high speed, low power UT54ACS164245S transceiver is designed to perform multiple functions including: asynchronous twoway communication, signal buffering, voltage translation, and cold sparing. With VDD equal to zero volts, the UT54ACS164245S outputs and inputs present a minimum impedance of 1M making it ideal for "cold spare" applications. Balanced outputs and low "on" output impedance make the UT54ACS164245S well suited for driving high capacitance loads and low impedance backplanes. The UT54ACS164245S enables system designers to interface 3.3 volt CMOS compatible components with 5 volt CMOS components. For voltage translation, the A port interfaces with the 3.3 volt bus; the B port interfaces with the 5 volt bus. The direction control (DIRx) controls the direction of data flow. The output enable (OEx) overrides the direction control and disables both ports. These signals can be driven from either port A or B. The direction and output enable controls operate these devices as either two independent 8-bit transceivers or one 16-bit transceiver. (47) (24) (44) 1A3 DESCRIPTION 2EN1 (BA) 2EN2 (AB) 1EN1 (BA) 1EN2 (AB) (8) 1B1 1B2 1B3 1B4 1B5 (9) 1B6 (11) 1B7 (12) 1B8 (13) 2B1 21 22 (35) (14) 2B2 (16) 2B3 (17) 2B4 (19) 2B5 (20) 2B6 (22) 2B7 (23) 2B8 (33) (32) 2A4 (30) 2A5 (29) 2A6 (27) 2A7 (26) 2A8 PIN DESCRIPTION Pin Names Description OEx Output Enable Input (Active Low) DIRx Direction Control Inputs xAx Side A Inputs or 3-State Outputs (3.3V Port) xBx Side B Inputs or 3-State Outputs (5V Port) FUNCTION TABLE 1 ENABLE OEx DIRECTION DIRx OPERATION L L B Data To A Bus L H A Data To B Bus H X Isolation PINOUTS POWER TABLE1 48-Lead Flatpack Top View DIR1 1 48 OE1 1B1 2 47 1A1 1B2 3 46 VSS 1B3 4 5 45 44 1A2 VSS 1A3 1B4 6 43 1A4 VDD1 7 42 VDD2 1B5 1B6 VSS 8 9 10 41 40 39 1A5 1A6 VSS 1B7 11 38 1A7 1B8 12 37 1A8 2B1 13 36 2A1 2B2 VSS 14 15 35 34 2A2 VSS 2B3 16 33 2A3 2B4 17 32 2A4 VDD1 2B5 2B6 VSS 18 19 20 21 31 30 29 28 VDD2 2A5 2A6 VSS 2B7 2B8 DIR2 22 23 24 27 26 25 2A7 2A8 OE2 Port B Port A OPERATION 5 Volts 3.3 Volts Voltage Translator 5 Volts 5 Volts Non Translating 3.3 Volts 3.3 Volts Non Translating VSS VSS Cold Spare VSS 3.3V or 5V Port B Cold Spare NOTE: 1. VDD2 cannot be tied to VSS while power is applied to VDD1. Control signals DIRx and OEx are 5 volt tolerant inputs. When VDD2 is at 3.3 volts, either 3.3 or 5 volt CMOS logic levels can be applied to all control inputs. For proper operation connect power to all VDD and ground all VSS pins (i.e., no floating VDD or VSS input pins). Tie unused inputs to VSS. If VDD1 and VDD2 are not powered up together, then VDD2 should be powered up first for proper control of OE and DIR. Until VDD2 reaches 2.75V + 5%, control of the outputs by OE and DIR cannot be guaranteed. During operation of the part, after power up, insure VDD1 > VDD2. Tie unused inputs to VSS. 2 LOGIC DIAGRAM 2A1 3.3V PORT 1A4 (20) 2A7 (22) 2A8 (12) 3 2B7 (26) (23) 1B8 2B6 (27) 1B7 (37) 2B5 (29) 1B6 (38) 2B4 (30) (19) 2A6 (11) 1A8 (17) 2A5 2B3 (32) 1B5 (40) (9) 1A7 1B4 (41) (8) 1A6 (16) 2A4 2B2 (33) 1B3 (43) (6) 1A5 (14) 2A3 2B1 (35) 1B2 (44) OE2 (36) (13) 2A2 (5) (25) 1B1 (46) (3) 1A3 (24) OE1 (47) (2) 1A2 DIR2 3.3V PORT 1A1 (48) 2B8 5 V PORT (1) 5 V PORT DIR1 RADIATION HARDNESS SPECIFICATIONS 1 PARAMETER LIMIT UNITS Total Dose 1.0E5 rad(Si) SEL Latchup >120 MeV-cm2/mg Neutron Fluence2 1.0E14 n/cm2 Notes: 1. Logic will not latchup during radiation exposure within the limits defined in the table. 2. Not tested, inherent of CMOS technology. ABSOLUTE MAXIMUM RATINGS1 SYMBOL PARAMETER LIMIT (Mil only) UNITS VI/O (Port B)2 Voltage any pin during operation -.3 to VDD1 +.3 V VI/O (Port A)2 Voltage any pin during operation -.3 to VDD2 +.3 VDD1 Supply voltage -0.3 to 6.0 V VDD2 Supply voltage -0.3 to 6.0 V TSTG Storage Temperature range -65 to +150 C TJ Maximum junction temperature +175 C JC Thermal resistance junction to case 20 C/W II DC input current 10 mA PD Maximum power dissipation 1 W Note: 1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods may affect device reliability and performance. 2. For cold spare mode (VDD = VSS), VI/O may be -0.3V to the maximum recommended operating VDD + 0.3V. DUAL SUPPLY OPERATING CONDITIONS SYMBOL PARAMETER LIMIT UNITS VDD1 Supply voltage 3.0 to 3.6 or 4.5 to 5.5 V VDD2 Supply voltage 3.0 to 3.6 or 4.5 to 5.5 V VIN (Port B) Input voltage any pin 0 to VDD1 V VIN (Port A) Input voltage any pin 0 to VDD2 V TC Temperature range -55 to + 125 C 4 DC ELECTRICAL CHARACTERISTICS 1 ( -55C < TC < +125C) (TC = -55C to +125C for "C" screening and -40C to +125C for "W" screening) SYMBOL PARAMETER CONDITION VT + Schmitt Trigger, positive going threshold2 VT- Schmitt Trigger, negative going threshold2 VDD from 3.00 to 5.5 VH1 Schmitt Trigger range of hysteresis10 VH2 IIN MIN VDD from 3.00 to 5.5 MAX UNIT .7VDD V .3VDD V VDD from 4.5 to 5.5 0.6 V Schmitt Trigger range of hysteresis10 VDD from 3.00 to 3.6 0.4 V Input leakage current10 VDD from 3.6 to 5.5 -1 3 A -1 3 A -1 5 A -200 200 mA -100 100 mA IOL= 8mA 0.4 V IOL= 100A 0.2 VIN = VDD or VSS IOZ Three-state output leakage current10 VDD from 3.6 to 5.5 VIN = VDD or VSS ICS Cold sparing leakage current3 VIN = 5.5 VDD = VSS IOS1 Short-circuit output current 6, 11 VO = VDD or VSS VDD from 4.5 to 5.5 IOS2 Short-circuit output current 6, 11 VO = VDD or VSS VDD from 3.00 to 3.6 VOL1 Low-level output voltage4, 10 VDD = 4.5 VOL2 Low-level output voltage4, 10 IOL= 8mA 0.5 IOL= 100A 0.2 V VDD = 3.00 VOH1 High-level output voltage4, 10 IOH= -8mA IOH= -100A VDD - 0.7 V VDD - 0.2 VDD = 4.5 VOH2 High-level output voltage4, 10 IOH= -8mA VDD - 0.9 IOH= -100A VDD - 0.2 VDD = 3.00 5 V Ptotal1 CL = 50pF Power dissipation 5,7, 8 2.0 mW/ MHz 1.5 mW/ MHz A A VDD from 4.5 to 5.5 Ptotal2 Power dissipation 5, 7, 8 CL = 50pF VDD from 3.00 to 3.6 IDD Standby Supply Current VDD1 or VDD2 VIN = VDD or VSS VDD = 5.5 Pre-Rad 25oC Pre-Rad -55 C to +125 C OE=VDD 10 100 Post-Rad 25oC OE=VDD 500 A Input capacitance 9 = 1MHz @ 0V 15 pF 15 pF o CIN OE=VDD o VDD from 3.00 to 5.5 COUT Output capacitance9 = 1MHz @ 0V VDD from 3.00 to 5.5 Notes: 1. All specifications valid for radiation dose 1E5 rad(Si) per MIL-STD-883, Method 1019. 2. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: VIH = VIH(min) + 20%, - 0%; VIL = VIL(max) + 0%, 50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are guaranteed to VIH(min) and VIL(max). 3. All combinations of OEx and DIRx 4. Per MIL-PRF-38535, for current density 5.0E5 amps/cm2, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765 pF-MHz. 5. Guaranteed by characterization. 6. Not more than one output may be shorted at a time for maximum duration of one second. 7. Power does not include power contribution of any CMOS output sink current. 8. Power dissipation specified per switching output. 9.Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and VSS at frequency of 1MHz and a signal amplitude of 50mV rms maximum. 10.Guaranteed; tested on a sample of pins per device. 11. Supplied as a design limit, but not guaranteed or tested. . 6 AC ELECTRICAL CHARACTERISTICS1 (Port B = 5 Volt, Port A = 3.3 Volt) (VDD1 = 5V 10%; VDD2 = 3.00V to 3.6V, -55C < TC < +125C) (TC = -55C to +125C for "C" screening and -40C to +125C for "W" screening) SYMBOL PARAMETER MIN MAX UT54ACS164245S MIN MAX UNIT UT54ACS164245SE tPLH Propagation delay Data to Bus 1 20 3.5 11 ns tPHL Propagation delay Data to Bus 1 20 3.5 11 ns tPZL Output enable time OEx to Bus 1 18 2.5 16 ns tPZH Output enable time OEx to Bus 1 18 2.5 16 ns tPLZ Output disable time OEx to Bus high impedance 1 20 2.5 16 ns tPHZ Output disable time OEx to Bus high impedance 1 20 2.5 16 ns tPZL2 Output enable time DIRx to Bus 1 18 1 18 ns tPZH2 Output enable time DIRx to Bus 1 18 1 18 ns tPLZ2 Output disable time DIRx to Bus high impedance 1 20 1 20 ns tPHZ2 Output disable time DIRx to Bus high impedance 1 20 1 20 ns tSKEW3 Skew between outputs - 600 ps tDSKEW4 Differential skew between outputs - 1.5 ns Notes: 1. All specifications valid for radiation dose 1E5 rad(Si) per MIL-STD-883, Method 1019. 2. DIRx to bus times are guaranteed by design, but not tested. OEx to bus times are tested 3. Output skew is defined as a comparison of any two output transitions high-to-low vs. high-to-low and low-to-high vs low-to-high. 4. Differential skew is defined as a comparison of any two output transitions high-to-low vs. low-to-high and low-to-high vs high-to low. 7 Propagation Delay Input tPLH VDD VDD/2 0V tPHL VOH VDD/2 VOL Output Enable Disable Times Control Input 5V Output Normally Low 5V Output Normally High tPZL tPLZ VDD/2-0.2 tPHZ tPZH VDD/2+0.2 .8VDD - .2V tPLZ tPZL 3.3V Output Normally Low 3.3V Output Normally High .2VDD + .2V VDD/2-0.2 .2VDD + .2V tPHZ tPZH VDD/2+0.2 8 .7VDD - .2V VDD VDD/2 0V VDD/2 .2VDD .8VDD VDD/2 VDD/2 .2VDD .7VDD VDD/2 AC ELECTRICAL CHARACTERISTICS1 (Port A = Port B, 5 Volt Operation) (VDD1 = 5V 10%; VDD2 = 5.0V +10%, -55C < TC < +125C) SYMBOL PARAMETER MIN MAX UT54ACS164245S MIN MAX UNIT UT54ACS164245SE tPLH Propagation delay Data to Bus 1 15 3.5 9 ns tPHL Propagation delay Data to Bus 1 15 3.5 9 ns tPZL Output enable time OEx to Bus 1 12 3 9 ns tPZH Output enable time OEx to Bus 1 12 3 9 ns tPLZ Output disable time OEx to Bus high impedance 1 15 3 9 ns tPHZ Output disable time OEx to Bus high impedance 1 15 3 9 ns tPZL2 Output enable time DIRx to Bus 1 12 1 12 ns tPZH2 Output enable time DIRx to Bus 1 12 1 12 ns tPLZ2 Output disable time DIRx to Bus high impedance 1 15 1 15 ns tPHZ2 Output disable time DIRx to Bus high impedance 1 15 1 15 ns tSKEW3 Skew between outputs - 600 ps tDSKEW4 Differential skew between outputs - 1.5 ns Notes: 1. All specifications valid for radiation dose 1E5 rad(Si) per MIL-STD-883, Method 1019. 2. DIRx to bus times are guaranteed by design, but not tested. OEx to bus times are tested 3. Output skew is defined as a comparison of any two output transitions high-to-low vs. high-to-low and low-to-high vs low-to-high. 4. Differential skew is defined as a comparison of any two output transitions high-to-low vs. low-to-high and low-to-high vs high-to low. 9 Propagation Delay Input tPLH VDD VDD/2 0V tPHL VOH VDD/2 VOL Output Enable Disable Times Control Input 5V Output Normally Low 5V Output Normally High tPZL tPLZ .2VDD + .2V VDD/2-0.2 tPHZ tPZH VDD/2+0.2 .8VDD - .2V Propagation Delay Input tPLH VDD VDD/2 0V VDD/2 .2VDD .8VDD VDD/2 VDD VDD/2 0V tPHL VOH VDD/2 VOL Output Enable Disable Times Control Input 3.3V Output Normally Low 3.3V Output Normally High tPZL tPLZ VDD/2-0.2 .2VDD + .2V tPHZ tPZH VDD/2+0.2 10 .7VDD - .2V VDD VDD/2 0V VDD/2 .2VDD .7VDD VDD/2 AC ELECTRICAL CHARACTERISTICS1 (Port A = Port B, 3.3 Volt Operation) (VDD1 = 3.00V to 3.6V; VDD2 = 3.00V to 3.6V, -55C < TC < +125C) SYMBOL PARAMETER MIN MAX UT54ACS164245S MIN MAX UNIT UT54ACS164245SE tPLH Propagation delay Data to Bus 1 20 3.5 11 ns tPHL Propagation delay Data to Bus 1 20 3.5 11 ns tPZL Output enable time OEx to Bus 1 18 2.5 16 ns tPZH Output enable time OEx to Bus 1 18 2.5 16 ns tPLZ Output disable time OEx to Bus high impedance 1 20 2.5 16 ns tPHZ Output disable time OEx to Bus high impedance 1 20 2.5 16 ns tPZL2 Output enable time DIRx to Bus 1 18 1 18 ns tPZH2 Output enable time DIRx to Bus 1 18 1 18 ns tPLZ2 Output disable time DIRx to Bus high impedance 1 20 1 20 ns tPHZ2 Output disable time DIRx to Bus high impedance 1 20 1 20 ns tSKEW3 Skew between outputs 600 ps tDSKEW4 Differential skew between outputs 1.5 ns Notes: 1. All specifications valid for radiation dose 1E5 rad(Si) per MIL-STD-883, Method 1019. 2. DIRx to bus times are guaranteed by design, but not tested. OEx to bus times are tested. 3. Output skew is defined as a comparison of any two output transitions high-to-low vs. high-to-low and low-to-high vs low-to-high. 4. Differential skew is defined as a comparison of any two output transitions high-to-low vs. low-to-high and low-to-high vs high-to low. 11 PACKAGE 5 6 4 6 1. All exposed metalized areas are gold plated over electroplated nickel per MIL-PRF-38535. 2. The lid is electrically connected to VSS. 3. Lead finishes are in accordance with MIL-PRF-38535. 4. Lead position and colanarity are not measured. 5. ID mark symbol is vendor option. 6. With solder, increase maximum by 0.003. Figure 1. 48-Lead Flatpack 12 ORDERING INFORMATION UT54ACS164245S: SMD 5962 R 98580 ** * * * Lead Finish: (C) = Gold Case Outline: (X) = 48 lead BB FP (Gold only) Class Designator: (Q) = Class Q (V) = Class V Device Type (01) = 16-bit MultiPurpose Transceiver (3.13V - 5.5V) (02) = 16-bit MultiPurpose Transceiver (3.0V - 5.5V) (03) = Extended Industrial Temp (-40oC to +125oC) (04) = 16-bit MultiPurpose Transceiver with enhanced AC's (05) = Extended Industrial Temp (-40oC to +125oC) with enhanced AC's Drawing Number: 98580 Total Dose: (R) = 1E5 rad(Si) Federal Stock Class Designator: No options Notes: 1. Total dose radiation must be specified when ordering. QML Q and QML V not available without radiation hardening. Notes: 1. Military Temperature Range flow per UTMC Manufacturing Flows Document. Devices are tested -55C, room temp, and 125C. Radiation neither tested nor guaranteed. 2. Prototype flow per UTMC Manufacturing Flows Document Tested at 25C only. Lead finish is gold only. 3. Extended Industrial Temperature Range Flow per UTMC Manufacturing Flows Document. Devices are tested at -40oC, room temp, and +125oC. Radiation is neither tested nor guaranteed 13 UT54ACS164245S UT54 *** ****** -* * * Lead Finish: (C) = Gold Screening: (C) = Mil Temp (P) = Prototype (W) = Extended Industrial Temp (-40oC to +125oC) Package Type: (U) = 48-lead BB FP (Gold only) Part Number: (164245S) = 16-bit MultiPurpose Transceiver (164245SE) = 16-bit MultiPurpose Transceiver Extended Performance I/O Type: (ACS)= CMOS compatible I/O Level UTMC Core Part Number 14 COLORADO Toll Free: 800-645-8862 Fax: 719-594-8468 INTERNATIONAL Tel: 805-778-9229 Fax: 805-778-1980 NORTHEAST Tel: 603-888-3975 Fax: 603-888-4585 SE AND MID-ATLANTIC Tel: 321-951-4164 Fax: 321-951-4254 WEST COAST Tel: 949-362-2260 Fax: 949-362-2266 CENTRAL Tel: 719-594-8017 Fax: 719-594-8468 www.aeroflex.com info-ams@aeroflex.com Aeroflex Colorado Springs, Inc. reserves the right to make changes to any products and services herein at any time without notice. Consult Aeroflex or an authorized sales representative to verify that the information in this data sheet is current before using this product. Aeroflex does not assume any responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in writing by Aeroflex; nor does the purchase, lease, or use of a product or service from Aeroflex convey a license under any patent rights, copyrights, trademark rights, or any other of the intellectual rights of Aeroflex or of third parties. Our passion for performance is defined by three attributes represented by these three icons: solution-minded, performance-driven and customer-focused 15