M600 M.2 Type 2260/2280 NAND Flash SSD Features M600 M.2 Type 2260/2280 NAND Flash SSD MTFDDAV128MBF, MTFDDAV256MBF, MTFDDAV512MBF, MTFDDAY128MBF, MTFDDAY256MBF, MTFDDAY512MBF Features * * * * * * * * * * * * * * * * * * * * Reliability - MTTF: 1.5 million device hours3 - Static and dynamic wear leveling - Uncorrectable bit error rate (UBER): <1 sector per 1015 bits read * Low power consumption - 150mW TYP 4 * Endurance: Total bytes written (TBW) - Up to 300TB * Capacity (unformatted): 128GB, 256GB, 512GB * Mechanical - M.2 "Socket 2" connector: 3.3V 5% - Type 2260: 60mm x 22mm x 3.6mm - Type 2280: 80mm x 22mm x 2.3mm - Weight: 10g (MAX) * Secure firmware update with digitally signed firmware image * Operating temperature - Commercial (0C to +70C)5 Micron(R) 16nm MLC NAND Flash RoHS-compliant package SATA 6 Gb/s interface TCG/Opal 2.0-compliant self-encrypting drive (SED) Compatible with Microsoft eDrive(R) Hardware-based AES-256 encryption engine ATA modes supported - PIO mode 3, 4 - Multiword DMA mode 0, 1, 2 - Ultra DMA mode 0, 1, 2, 3, 4, 5, 6 Industry-standard, 512-byte sector size support Device Sleep (DEVSLP), extreme low power mode Native command queuing support with 32-command slot support ATA-8 ACS3 command set compliant ATA security feature command set and password login support Secure erase (data page) command set: fast and secure erase Sanitize device feature set support Self-monitoring, analysis, and reporting technology (SMART) command set Dynamic write acceleration Adaptive thermal monitoring Power loss protection for data-at-rest Performance1, 2 - PCMark(R) Vantage (HDD test suite score): up to 87,000 - Sequential 128KB READ: up to 560 MB/s - Sequential 128KB WRITE: up to 510 MB/s - Random 4KB READ: up to 100,000 IOPS - Random 4KB WRITE: up to 88,000 IOPS - READ/WRITE latency: 120s/30s (TYP) PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Notes: 1. Typical I/O performance numbers as measured fresh-out-of-box (FOB) using Iometer with a queue depth of 32 and write cache enabled. 2. 4KB transfers used for READ/WRITE latency values. 3. The product achieves a mean time to failure (MTTF) based on population statistics not relevant to individual units. 4. Active average power measured during execution of MobileMark(R) with DIPM (deviceinitiated power management) enabled. 5. Temperature measured by SMART attribute 194. Warranty: Contact your Micron sales representative for further information regarding the product, including product warranties. 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. M600 M.2 Type 2260/2280 NAND Flash SSD Features Part Numbering Information Micron's M600 SSD is available in different configurations and densities. The chart below is a comprehensive list of options for the M600 series devices; not all options listed can be combined to define an offered product. Visit www.micron.com for a list of valid part numbers. Figure 1: Part Number Chart MT FD D AV 128 M BF - 1 AN 1 2 AB YY ES Micron Technology Production Status Product Family FD = Flash drive Blank = Production ES = Engineering sample MS = Mechanical sample Drive Interface Customer Designator D = SATA 6.0 Gb/s YY = Standard Drive Form Factor Feature Set AK = 2.5-inch (7mm) AT = mSATA AV = M.2 (80mm x 22mm 2.3mm) AY = M.2 (60mm x 22mm 3.5mm) AA = Contact factory AB = Standard AC = Contact factory ZZ = Blank Drive Density Extended Firmware Features 064 = 64GB 128 = 128GB 256 = 256GB 512 = 512GB 1T0 = 1024GB Z = Non-Encrypted 1 = Contact factory 2 = SED (self-encrypting drive) Sector Size 1 = 512 byte NAND Flash Type NAND Flash Component M = MLC AN = 128Gb, MLC, x8, 3.3V (16nm) Product Family BOM Revision BF = M600 For example: 1 = 1st generation 2 = 2nd generation PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD General Description General Description Micron's solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and 8-channels of Micron NAND Flash internally. Packaged in an HDD replacement enclosure, the SSD integrates easily in existing storage infrastructures. The SSD is designed to use the SATA interface efficiently during both READs and WRITEs while delivering bandwidth-focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption, and extended reliability. The M.2 Type 2260 and 2280 are caseless form factors ideally suited for ultrathin, mobile computing applications, which require mass storage in a very small footprint. The self-encypting drive (SED) features a FIPS-compliant, AES-256 encryption engine, providing hardware-based, secure data encryption, with no loss of SSD performance. This SED follows the TCG/Opal specification for trusted peripherals. When TCG/Opal features are not enabled, the device can perform alternate data encryption by invoking the ATA security command-set encryption features, to provide fulldisk encryption (FDE) managed in the host system BIOS. TCG/Opal and ATA security feature sets cannot be enabled simultaneously. The data encryption is always running; however, encryption keys are not managed and the data is not secure until either TCG/Opal or ATA security feature sets are enabled. Figure 2: Functional Block Diagram NAND SATA SSD controller NAND NAND NAND NAND DRAM buffer PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Logical Block Address Configuration Logical Block Address Configuration The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified capacity. Standard LBA settings, based on the IDEMA standard (LBA1-03), are shown below. Table 1: Standard LBA Settings Total LBA Capacity User Available Bytes Max LBA Decimal Hexadecimal Decimal Hexadecimal (Unformatted) 128GB 250,069,680 EE7C2B0 250,069,679 EE7C2AF 128,035,676,160 256GB 500,118,192 1DCF32B0 500,118,191 1DCF32AF 256,060,514,304 512GB 1,000,215,216 3B9E12B0 1,000,215,215 3B9E12AF 512,110,190,592 Physical Configuration Table 2: Dimensions and Weight Value Specification Nom Max Unit - 3.58 mm Width 22.00 - mm Length 60.00 or 80.00 - mm - 10 g 10 - insert/remove cycles Height Unit weight Insertion rating Interface Connectors Figure 3: SSD Interface Connections Primary side P75 P57 P67 PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Secondary side P2 P20 P10 P21 P1 P11 4 P58 P74 P68 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Interface Connectors Table 3: Signal Assignments Primary Side Pin # Secondary Side Signal Name Description 1 GND (PRESENCE) Ground 3 GND Ground 5 GND 7 Pin # Signal Name Description 2 3V3 +3.3V 4 3V3 +3.3V No connect 6 Reserved No connect DNU No connect 8 Reserved No connect 9 DNU Ground 10 DAS/DSS Drive activity (host LED) 11 GND Ground Key Key 20 Reserved No connect 21 GND (Direct to P69) No connect 22 Reserved No connect 23 DNU No connect 24 Reserved No connect 25 DNU No connect 26 Reserved No connect 27 GND Ground 28 Reserved No connect 29 Reserved No connect 30 Reserved No connect 31 Reserved No connect 32 Reserved No connect 33 GND Ground 34 Reserved No connect 35 Reserved No connect 36 Reserved No connect 37 Reserved No connect 38 DEVSLP Device sleep 39 GND Ground 40 Reserved No connect 41 SATA +B 42 Reserved No connect 43 SATA -B SATA B differential pair 44 Reserved No connect 45 GND Ground 46 Reserved No connect 47 SATA -A Reserved No connect SATA +A SATA A differential pair 48 49 50 Reserved No connect 51 GND Ground 52 Reserved No connect 53 Reserved No connect 54 Reserved No connect 55 Reserved No connect 56 Reserved Vendor use 57 GND Ground 58 Reserved Vendor use Key Key 67 DNU No connect 68 SUSCLK No connect 69 PEDET Ground 70 3V3 +3.3V 71 GND Ground 72 3V3 +3.3V 73 GND Ground 74 3V3 +3.3V 75 GND Ground PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 5 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Performance Performance Measured performance can vary for a number of reasons. The major factors affecting drive performance are the capacity of the drive and the interface of the host. Additionally, overall system performance can affect the measured drive performance. When comparing drives, it is recommended that all system variables are the same, and only the drive being tested varies. Performance numbers will vary depending on the host system configuration. For SSDs designed for the client computing market, Micron specifies performance in fresh-out-of-box (FOB) state. Data throughput measured in "steady state" may be lower than FOB state, depending on the nature of the data workload. For a description of these performance states and of Micron's best practices for performance measurement, refer to Micron's technical marketing brief "Best Practices for SSD Performance Measurement" (www.micron.com/products/solid-state-storage/). Table 4: Drive Performance Capacity 128GB 256GB 512GB Interface Speed 6 Gb/s 6 Gb/s 6 Gb/s Unit PCMark Vantage 87,000 87,000 87,000 HDD score Sequential read (128KB transfer) 600 600 600 MB/s Sequential write (128KB transfer) 350 500 500 MB/s Random read (4KB transfer) 90,000 100,000 100,000 IOPS Random write (4KB transfer) 88,000 88,000 88,000 IOPS READ latency (TYP) 120 120 120 s WRITE latency (TYP) 30 30 30 s Notes: PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 1. Performance numbers are maximum values, except as noted. 2. Typical I/O performance numbers as measured using Iometer with a queue depth of 32 and write cache enabled. Fresh-out-of-box (FOB) state is assumed. For performance measurement purposes, the SSD may be restored to FOB state using the secure erase command. 3. Iometer measurements are performed on an 20GB span of logical block addresses (LBAs). 4. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values with write cache enabled. 5. System variations will affect measured results. For comparison, PCMark scores are measured with the SSD as a secondary drive in a two-drive system. When measured as an OS drive, system overhead can cause lower scores. 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Reliability Reliability Micron's SSDs incorporate advanced technology for defect and error management. They use various combinations of hardware-based error correction algorithms and firmware-based static and dynamic wear-leveling algorithms. Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but when it is read out of the SSD, the data differs from what was programmed. Table 5: Uncorrectable Bit Error Rate Uncorrectable Bit Error Rate Operation 1015 READ <1 sector per bits read Mean Time To Failure Mean time to failure (MTTF) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability prediction procedures for electronic equipment. Table 6: MTTF MTTF (Operating Hours)1 Capacity Note: PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 64GB 1.5 million 128GB 1.5 million 256GB 1.5 million 512GB 1.5 million 1. The product achieves a mean time to failure (MTTF) of 1.5 million hours, based on population statistics not relevant to individual units. 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Reliability Endurance Endurance for the SSD can be predicted based on the usage conditions applied to the device, the internal NAND component cycles, the write amplification factor, and the wear-leveling efficiency of the drive. The tables below show the drive lifetime for each SSD capacity by client computing and sequential input and based on predefined usage conditions. Table 7: Drive Lifetime - Client Computing Capacity Notes: PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Drive Lifetime (Total Bytes Written) 128GB 100TB 256GB 200TB 512GB 300TB 1. Total bytes written validated with the drive 90% full. 2. SSD volatile write cache is enabled. 3. Access patterns used during reliability testing are 25% sequential and 75% random and consist of the following: 50% are 4 KiB; 40% are 64 KiB; and 10% are 128 KiB. 4. Host workload parameters, including write cache settings, I/O alignment, transfer sizes, randomness, and percent full, that are substantially different than the described notes may result in varied endurance results. 5. GB/day can be calculated by dividing the total bytes written value by (365 x number of years). For example: 100 TB/5 years/365 days = 54 GB/day for 5 years. 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Electrical Characteristics Electrical Characteristics Environmental conditions beyond those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Table 8: SATA Power Consumption Device Sleep Typical Idle Average Active Average Active Maximum (128KB transfer) Unit 128GB 2 70 150 3600 mW 256GB 2 70 150 4400 mW 512GB 2 70 150 4700 mW Capacity Notes: 1. 2. 3. 4. Data taken at 25C using a 6 Gb/s SATA interface. Active average power measured while running MobileMark Productivity Suite. DIPM (device-initiated power management) enabled. DIPM Slumber supported. Active maximum power is an average power measurement performed using Iometer with 128KB sequential write transfers. Table 9: Maximum Ratings Parameter/Condition Symbol Min Max 3V3 3.14 3.46 V TC 0 70 C Non-operating temperature -40 85 C Rate of temperature change - 20 C/hour Relative humidity (non-condensing) 5 95 % Voltage input Operating temperature Note: Unit Notes 1 1. Operating temperature is best measured by reading the SSD's on-board temperature sensor, which is recorded in SMART attribute 194 (or 0xC2). Table 10: Shock and Vibration Parameter/Condition Specification Non-operating shock 1500G/0.5ms Non-operating vibration PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 5-800Hz @ 3.13G 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Dynamic Write Acceleration Dynamic Write Acceleration Dynamic write acceleration optimizes SSD performance for typical client-computing environments, where WRITE operations tend to occur in bursts of commands with idle time between these bursts. Capacity for accelerated performance is derived from the adaptive usage of the SSD's native NAND array, without sacrificing user-addressable storage. Recent advances in Micron NAND technology enable the SSD firmware to achieve acceleration through onthe-fly mode switching between SLC and MLC modes to create a high-speed SLC pool that changes in size and location with usage conditions. During periods of idle time between write bursts, the drive may free additional capacity for accelerated write performance. The amount of accelerated capacity recovered during idle time depends on the portion of logical addresses that contain user data and other runtime parameters. In applications that do not provide sufficient idle time, the device may need to perform SLC-to-MLC data migration during host activity. Under accelerated operation, write performance may be up to 2.8 times higher than non-accelerated operations. Power consumption per-byte written is lower during accelerated operation, which may reduce overall power consumption and heat production. The following table shows the form factors and capacities that feature dynamic write acceleration. Table 11: Dynamic Write Acceleration - Capacities and Form Factors M600 Form Factors 128GB 256GB 512GB 1024GB 2.5" 7mm on on off off M.2 2280, single-sided on on on - M.2 2260, double-sided on on on - mSATA on on on - PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Adaptive Thermal Monitoring Adaptive Thermal Monitoring The device features adaptive thermal monitoring. While most host computers exhibit operating environments that keep an SSD running in the range of 40C to 45C, adaptive thermal monitoring enables the SSD device to operate in a wide variety of environments by helping to prevent the host computer from running at excessive temperatures. Adaptive thermal monitoring reduces total SSD power consumption by the device controller, as well as the NAND media, by injecting time-based delays between internal processing of media commands when the device temperature reaches 75 C. The delay times used are bound to the microsecond range, and are based on a proportional and differential control equation of the general form shown here. Figure 4: Adaptive Thermal Monitoring Control Equation u(t) = Kp x Tp(t) + Kd x dTd dt The delay-control equation is tuned for a steady-state temperature target, which has been designed as an optimum balance of hardware temperature tolerances and drive performance. Steady-state temperature targets are hardware-configuration dependant, and may range from 80 C to 84 C. Temperatures below the intended steady-state target will not produce a proportional component to delay, but may produce a differential component based on the current rate of temperature change according to the control equation. When the feature is active, DRAM refresh rates are also adjusted to improve data integrity and stability while operating outside of temperature specifications. When the device temperature falls below 73 C, normal operation will continue without induced delays. If temperature continues to rise above the temperature target and exceeds a hardware-dependant critical threshold, the device will abort host commands to prevent component damage. The critical threshold values have a 6 C margin on top of target threshold, and range between 86 C and 90 C. Device temperature values used by the adaptive thermal monitoring feature are based on an internal temperature sensor located on the device PCB, and may differ from case or package temperatures as measured by thermocouple. Device temperature is accessible through SMART attribute 194, though usage of the SMART feature is not necessary for adaptive thermal monitoring functionality. Adaptive thermal monitoring does not change the current negotiated speed of the SATA bus, nor require or cause any new commands to be issued on the SATA bus. Ratedthroughput performance is not guaranteed at any point above the maximum specified operating temperature. PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD TCG/Opal Support TCG/Opal Support Table 12: TCG/Opal Support Parameters Property Supported? Comments TCG Storage Specifications OPAL: TCG Storage Security SubSystem Class Specification 2.00 Revision 1.00, Feb 24, 2012 TCG Core Specification Specification 2.00 Revision 2.00, Nov 4, 2011 TCG Storage Interface Interactions Specification TCG Reference Specification Specification Version 1.02 Revision 1.00 30 December, 2011 OPAL SSC 1.00 (backward compatibility) Not supported - OPAL SSC Additional Feature Set Specification Additional DataStore Table Supported Specification 1.00 Revision 1.00, Feb 24, 2012 Single User Mode Supported Specification 1.00 Revision 1.00, Feb 24, 2012 TCG Storage Protection Mechanisms for Secrets Supported Specification Version 1.00 Revision 1.07 17 August, 2011 PSID - Physical Presence SID Supported Specification Version 1.00 Committee Draft Revision 1.05 February 9, 2011 GUDID (Globally Unique Serial Number) Supported Mandatory GUDID Proposal 11/03/2011 (Microsoft) SID Authority Disable Supported SID Authority Disable Proposal 9/26/2011 (Microsoft) Modifiable CommonName Columns Supported Modifiable CommonName Columns Proposal 7/22/2010 (Microsoft) ALL OPAL Mandatory Features Supported - Close Session (optional) Supported Allows Tper to notify the host it has aborted a session Restricted Command & Table (optional) Not Supported The interface control template enables TPer control over selected interface commands; the benefit is the reduction of undesired side effects Type Table (not required) OPAL SSC Feature Set - Specific List Not Supported - Activate Method Supported - Revert Method Supported - Revert SP Method Supported - Activate Method Within Transactions Not Supported As per OPAL, this behavior is out of the scope Revert Method within Transactions Not Supported As per OPAL, this behavior is out of the scope Revert SP Method within Transactions Not Supported As per OPAL, this behavior is out of the scope Creation/Deletion of Tables/Rows after Manufacturing Not Supported As per OPAL, this behavior is out of the scope COM ID Management Support Not Supported Dynamic COM ID allocation & management not supported Buffer Management Support Not Supported Flow control Tper Feature PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD TCG/Opal Support Table 12: TCG/Opal Support Parameters (Continued) Property Supported? Comments ACK/NACK Support Not Supported Session reliability Async Support Not Supported Asynchronous protocol support with multiple commands per session Geometry Reporting Feature ALIGN Supported OPAL 2.0 (only) Logical Block Size 512 bytes Logical block size = 512 Bytes Alignment Granularity 4096 Bytes Page or Descriptor size <> Lowest Aligned LBA 0 - OPAL SSC V2.00 Feature Descriptor Base COM ID 0x1000 0x1000-0xFFFF defined for COM ID management Number of COM IDs 1 - Range Crossing Behavior 0 If drive receives a READ or WRITE command that spans multiple LBA ranges and the LBA ranges are not locked, then: 1. Process the data transfer, if Range Crossing = 0 2. Terminate the command with "Other Invalid Command Parameter" if Range Crossing = 1 Number of Locking SP Admin Authorities Supported 4 As per OPAL 2.0, drive should support at least 4 admin Number of Locking SP User Authorities Supported 9 As per OPAL 2.0, drive should support at least 8 users Initial C_PIN_SID PIN Indicator 0x00 0x00 = The initial C_PIN_SID PIN value is equal to the C_PIN_MSID PIN value 0xFF = The initial C_PIN_SID PIN value is VU, and MAY not be equal to the C_PIN_MSID PIN value OPAL 2.0 (only) Customer-specific SID - Configurable Behavior of C_PIN_SID PIN upon Ter Revert 0x00 0x00 = The C_PIN_SID PIN value becomes the value of the C_PIN_MSID PIN column after successful invocation of revert on the admin SP's object in the SP table 0xFF = The C_PIN_SID PIN value changes to a VU value after successful invocation of revert on the admin SP's object in the SP table and MAY not be equal to the C_PIN_MSID PIN value OPAL 2.0 (only) Maximum number of DataStore Tables 9 The maximum number of the DataStore tables that the TPer supports, including the DataStore table defined in OPAL SSC 2.0 Maximum total size of DataStore Tables 90MB Specifies the maximum total size in bytes of all of the DataStore tables that TPer supports, including the DataStore table defined in OPAL SSC 2.0 DataStore Table Size Alignment 10MB - DataStore Table Feature PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD TCG/Opal Support Table 12: TCG/Opal Support Parameters (Continued) Property Supported? MBR Table 128MB Comments - Byte Table Access Granularity Mandatory Write Granularity Recommended Access Granularity 1 TPer enforces when the host invokes the set method on byte tables; it should be less than or equal to 8192; it should be less than or equal to Recommended Access Granularity, OPAL 2.0 (only) 8192 Tper recommends when the host invokes the set or get method on byte tables; it should be less than or equal to 8192 256 Bits AES key is generated by using CTR DRBG algorithm (FIPS Compliant) Cryptographic Features AES Key Size AES Mode Number of Ranges/Band Supported Re-Encryption CBC IV swapped 9 (8 user definable, 1 global range) Not Supported Key Management Crypto Erase Completion Time <1s Cryptographic Algorithms are Certified by FIPS-197 Now supporting 8 LBA ranges; range cross read and write allowed if LBA ranges are unlocked - Authentication data required. Conforms to TCG Storage Protection Mechanisms for Secrets; Specification version 1.00, Revision 1.00, 05 March 2012 Yes - Pending - AES 256-Bit CBC/ECB Mode Supported ECB mode used only for generating the random key by CTR DRBG CTR DRBG Supported - SHA 256 Supported - RSA 2048 Signature Verification Supported - TPer Communication Properties Max ComPacket Size 131072 256 sectors (128K) Max Response ComPacket Size 131072 256 sectors (128K) Max Packet Size 128512 - Max Individual Token Size 123904 - Max Packets 1 - Max SubPackets 1 - Max Sessions 1 Each session requires a set of buffers and variables Max Transaction Limit 1 Transaction are inside sessions Max Methods 1 Methods are contained in a transaction Max Authentications 2 - PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD TCG/Opal Support Table 12: TCG/Opal Support Parameters (Continued) Property Def Session Timeout Supported? Yes Comments The session timeout length (in milliseconds) used by the TPer by default IEEE1667 Probe Silo Supported - TCG Storage Silo Supported - Not Supported - Other than Probe and TCG Storage Silo IEEE1667 Major Version TBD As per current draft specification, major and minor versions are not yet decided IEEE1667 Minor Version TBD - Maximum P_OUT Transfer Size 131072 256 sectors (128K) Others FDE (ATA Security with Key Management) Secure Firmware Download PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Yes - Supported 15 Firmware image is validated by using SHA256 and RSA2048 algorithm (FIPS-compliant; certification pending) Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Device ID Table 13: Identify Device See Note 1 for setting definitions Word Bit(s) Setting Default Value 0 Description General configuration bit-significant information 15 F 0b 0 = ATA device 14-8 X 0000100b 7 F 0b 1 = Removable media device 1 = Fixed disk HDD Retired 6 F 1b 5-3 X 000b 2 V 0b Response incomplete 1 X 0b Retired 0 F 1 Retired 0b Reserved 3FFFh Obsolete 2 F C837h Specific configuration 3 F 0010h Obsolete 4 F 0000h 0000h 6 F 003Fh 7 (O)V 0000h 0000h 9 ( )X 0000h Retired 10 (M)F varies Serial number (20 ASCII characters) 20 ( )X 0000h 0000h 0000h 23 (M)F varies Firmware revision (8 ASCII characters) 27 (M)F varies Model number (40 ASCII characters) 15-8 F 80h 80h 7-0 F 10h 00h = Reserved 01h-FFh = Maximum number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands 47 48 Retired Obsolete Reserved for assignment by the CompactFlashTM Association Retired/Obsolete Trusted Computing feature set options 15 F 14 F 13-1 F 0 F PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 0b Shall be cleared to zero 1b Shall be set to one 0000000000000b Reserved for the Trusted Computing Group 1b 1=Trusted Computing feature set is support 16 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 49 Description Capabilities 15-14 F 00b Reserved for the IDENTIFY PACKET DEVICE command. 13 F 1b 1 = Standby timer values as specified in this standard are supported 0 = Standby timer values shall be managed by the device 12 F 0b Reserved for the IDENTIFY PACKET DEVICE command. 11 F 1b 1= IORDY supported 10 F 1b 1 = IORDY may be disabled 1b 1 = LBA supported 1 = DMA supported. 0 = IORDY may be supported 9 8 F 1b 7-0 F 00000000b 50 Capabilities 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13-2 F 000000000000b Reserved 1 X 0b Obsolete 0 F 1b Shall be set to one to indicate a vendor specific standby timer value minimum. ( )X 0000h 0000h 51 53 Obsolete 15-3 F 2 F 1b 1 = The fields reported in word 88 are valid 0 = the fields reported in word 88 are not valid 1 F 1b 1 = The fields reported in words (70:64) are valid 0 = the fields reported in words (70:64) are not valid 0 X 1b Obsolete ()X 3FFFh 0010h 003Fh FC10h 00FBh Obsolete 15 F 1b 1 = The BLOCK ERASE EXT command is supported 14 F 0b 1 = The OVERWRITE EXT command is supported 13 F 0b 1 = The CRYPTO SCRAMBLE EXT command is supported 1 = The Sanitize feature set is supported 54 59 Retired 0000000000000b Reserved 12 F 1b 11-9 F 000b 8 V 1b 7-0 V 00010000b 60-61 PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN M(F) Reserved 1 = Multiple sector setting is valid xxh = Current setting for number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands Varies by capacity Total number of user addressable logical sectors 17 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 62 63 64 Default Value Description ()X 0000h Obsolete 15-11 F 00000b Reserved 10 V 0b 1 = Multiword DMA mode 2 is selected 0 = Multiword DMA mode 2 is not selected 9 V 0b 1 = Multiword DMA mode 1 is selected 0 = Multiword DMA mode 1 is not selected 8 V 0b 1 = Multiword DMA mode 0 is selected 0 = Multiword DMA mode 0 is not selected 7-3 F 0000b 2 F 1b 1 = Multiword DMA mode 2 and below are supported 1 F 1b 1 = Multiword DMA mode 1 and below are supported 0 F 1b 1 = Multiword DMA mode 0 is supported 15-8 F 0 7-0 Reserved Reserved F 00000011b 65 F 0078h PIO modes supported Minimum Multiword DMA transfer cycle time per word Cycle time in nanoseconds 66 F 0078h Manufacturer's recommended Multiword DMA transfer cycle time Cycle time in nanoseconds 67 F 0078h Minimum PIO transfer cycle time without flow control Cycle time in nanoseconds 68 F 0078h Minimum PIO transfer cycle time with IORDY flow control Cycle time in nanoseconds 69 F Additional Supported 15 F 0b 1 = CFast Specification Support 14 F 1b 1 = Deterministic read after Trim is supported 13 F 0b 1 = Long Physical Sector Alignment Error Reporting Control is supported 12 F 0b 1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE CONFIGURATION SET DMA are supported 11 F 0b 1 = READ BUFFER DMA is supported 10 F 0b 1 = WRITE BUFFER DMA is supported 9 F 0b 1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA are supported 8 F 0b 1 = DOWNLOAD MICROCODE DMA is supported 7 F 1b Reserved for IEEE-1667 6 F 0b 1 = Optional ATA device 28-bit commands supported 5 F 1b 1 = Read zero after Trim is supported 4 F 1b 1 = Device encrypts all user data 3-0 F 0000b PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Reserved 18 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 70 F 0000h 71 F 0000h 0000h 0000h 0000h 15-5 F 00000000000b 4-0 F 11111b 75 Description Reserved Reserved for the IDENTIFY PACKET DEVICE command Queue depth 76 Reserved Maximum queue depth - 1 Serial ATA capabilities 15 F 0b 1 = Supports READ LOG DMA EXT as equivalent to READ LOG EXT 14 F 0b 1 = Supports device automatic partial to slumber transitions 13 F 0b 1 = Supports host automatic partial to slumber transitions 12 F 1b Supports Native Command Queuing priority information 11 F 0b Supports Unload while NCQ commands outstanding 10 F 1b Supports Phy event counters 9 F 0b Supports receipt of host initiated interface power management requests 8 F 1b Supports native Command Queueing 7-4 F 0000b 3 F 1b 1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s) 2 F 1b 1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s) 1 F 1b 1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s) 0 F 0b Reserved (set to 0) 77 Reserved for future Serial ATA signaling speed grades Serial ATA additional capabilities 15-8 F 00000000b 7 F 1b 1 = Supports DEVSLP_to_ReducedPwrState 6 F 1b Supports RECEIVE FPDMA QUEUED and SEND FPDMA QUEUED commands 5 F 0b Supports NCQ Queue Management Command 4 F 0b Supports NCQ Streaming 3-1 V 010b 0 F 0b PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Reserved for future Serial ATA definition Coded value indicating current negotiated Serial ATA signal speed Shall be cleared to zero 19 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 78 Description Serial ATA features supported 15-8 F 000000000b 7 F 0b 1 = Supports NCQ Autosense 6 F 1b 1 = Supports software settings preservation 5 F 1b 1 = HARDWARE FEATURE CONTROL SUPPORTED bit 4 F 0b 1 = Supports in-order data delivery 3 F 1b 1 = Supports dev initiate interface power management 2 F 1b 1 = Supports DMA Setup Auto-Activate optimization 1 F 0b 1 = Supports non-zero buffer offsets in DMA Setup FIS 0 F 0b Reserved (set to 0) 15-7 V 000000000b 6 V 1b 1 = Software settings preservation enabled 5 V 0b 1 = Asynchronous notification enabled 4 V 0b 1 = In-order data delivery enabled 3 V 0b 1 = Device initiating interface power management enabled 2 V 0b 1 = DMA Setup Auto-Activate optimization enabled 1 V 0b 1 = Non-zero buffer offsets in DMA Setup FIS enabled 0 V 0b Reserved (set to 0) 79 Reserved Serial ATA features enabled 80 Reserved Major revision number 15-10 F 000000b 9 F 1b 1 = Supports ATA8-ACS2 8 F 1b 1 = Supports ATA8-ACS 7 F 1b 1 = Supports ATA/ATAPI-7 6 F 1b 1 = Supports ATA/ATAPI-6 5 F 1b 1 = Supports ATA/ATAPI-5 4 F 1b 1 = Supports ATA/ATAPI-4 3 F 1b Obsolete 2 S 0b Obsolete 1 S 0b Obsolete 0 F 0b Reserved F 0028h 81 Reserved Minor revision number 0028h = ATA8-ACS version 6 PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 82 Description Command set supported 15 X 0b Obsolete 14 F 1b 1 = NOP command supported 13 F 1b 1 = READ BUFFER command supported 12 F 1b 1 = WRITE BUFFER command supported 11 X 0b Obsolete 10 F 1b 1 = Host Protected Area feature set supported 9 F 0b 1 = DEVICE RESET command supported 8 F 0b 1 = SERVICE interrupt supported 7 F 0b 1 = Release interrupt supported 6 F 1b 1 = Read look-ahead supported 5 F 1b 1 = Write cache supported 4 F 0b Shall be cleared to zero to indicate that the PACKET feature set is not supported. 3 F 1b 1 = Mandatory Power Management feature set supported 2 F 0b Obsolete 1 F 1b 1 = Security feature set supported 0 F 1b 1 = SMART feature set supported 83 Command set supported 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = FLUSH CACHE EXT command supported 12 F 1b 1 = Mandatory FLUSH CACHE command supported 11 F 1b 1 = Device Configuration Overlay feature set supported 10 F 1b 1 = 48-bit address feature set supported 9 F 0b 1 = Automatic Acoustic Management feature set supported 8 F 1b 1 = SET MAX security extension supported 7 F 0b See Address Offset Reserved Area Boot INCITS TR27:2001 6 F 0b 1 = SET FEATURES subcommand required to spin-up after power-up 5 F 0b 1 = Power-Up In Standby feature set supported 4 F 0b Obsolete 3 F 1b 1 = Advanced Power Management feature set supported 2 F 0b 1 = CFA feature set supported 1 F 0b 1 = READ/WRITE DMA QUEUED supported 0 F 1b 1 = DOWNLOAD MICROCODE command supported PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 84 Description Command set/feature supported extension 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported 12 F 0b Reserved for technical report INCITS TR-37-2004 (TLC) 11 F 0b Reserved for technical report INCITS TR-37-2004 (TLC) 10-9 F 00b Obsolete 8 F 1b 1 = 64-bit word wide name supported 7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported 6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported 5 F 1b 1 = General Purpose Logging feature set supported 4 F 0b 1 = Streaming feature set supported 3 F 0b 1 = Media Card Pass Through Command feature set supported 2 F 0b 1 = Media serial number supported 1 F 1b 1 = SMART self-test supported 0 F 1b 1 = SMART error logging supported 85 Command set/feature enabled. 15 X 0b Obsolete 14 F 1b 1 = NOP command supported 13 F 1b 1 = READ BUFFER command supported 12 F 1b 1 = WRITE BUFFER command supported 11 X 0b Obsolete 10 V 1b 1 = Host Protected Area feature set enabled 9 F 0b 1 = DEVICE RESET command supported 8 V 0b 1 = SERVICE interrupt enabled 7 V 0b 1 = Release interrupt enabled 6 V 1b 1 = Look-ahead enabled 5 V 1b 1 = Write cache enabled 4 F 0b Shall be cleared to zero to indicate that the PACKET feature set is not supported. 3 F 1b Power Management feature set is enabled 2 F 0b Obsolete 1 V 0b 1 = Security Mode feature set enabled 0 V 1b 1 = SMART feature set enabled PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 86 Description Command set/feature enabled. 15 1b 1 = Words 120-119 are valid 14 F 0b 1 = Reserved 13 F 1b 1 = FLUSH CACHE EXT command supported 12 F 1b 1 = FLUSH CACHE command supported 11 F 1b 1 = Device Configuration Overlay supported 10 F 1b 1 = 48-bit Address features set supported 9 V 0b 1 = Automatic Acoustic Management feature set enabled 8 F 0b 1 = SET MAX security enabled by SET MAX SET PASSWORD 7 F 0b Reserved for address Offset Reserved Area Boot, INCITS TR27:2001 6 F 0b 1 = SET FEATURES subcommand required to spin-up after power-up 5 V 0b 1 = Power-Up In Standby feature set enabled 4 V 0b Obsolete 3 V 1b 1 = Advanced Power Management feature set enabled 2 F 0b 1 = CFA feature set supported 1 F 0b 1 = READ/WRITE DMA QUEUED command supported 0 F 1b 1 = DOWNLOAD MICROCODE command supported 87 Command set/feature enabled/supported 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported 12 V 0b Reserved for technical report- INCITS tr-37-2004 (TLC) 11 V 0b Reserved for technical report- INCITS TR-37-2004 (TLC) 10-9 F 00b Obsolete 8 F 1b 1 = 64-bit word wide name supported 7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported 6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported 5 F 1b 1 = General Purpose Logging feature set supported 4 V 0b Obsolete 3 V 0b 1 = Media Card Pass Through Command feature set supported 2 V 0b 1 = Media serial number is valid 1 F 1b 1 = SMART self-test supported 0 F 1b 1 = SMART error logging supported PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 88 Default Value Description 0b Ultra DMA modes 15 0b Reserved 14 0b 1 = Ultra DMA mode 6 is selected 0 = Ultra DMA mode 6 is not selected 13 0b 1 = Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected 12 0b 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected 11 0b 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected 10 0b 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected 9 0b 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected 8 0b 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected 7 0b Reserved 6 1b 1 = Ultra DMA mode 6 and below are supported 5 1b 1 = Ultra DMA mode 5 and below are supported 4 1b 1 = Ultra DMA mode 4 and below are supported 3 1b 1 = Ultra DMA mode 3 and below are supported 2 1b 1 = Ultra DMA mode 2 and below are supported 1 1b 1 = Ultra DMA mode 1 and below are supported 0 1b 1 = Ultra DMA mode 0 IS supported 89 (O)F 0001h Time required for security erase unit completion 90 (O)F 0001h Time required for enhanced security erase completion 91 (O)V 00FEh Current advanced power management value 92 (O)V FFFEh Master Password Revision Code PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 93 Description Shall be 0000h for SATA devices 15 0b Shall be cleared to zero 14 0b Shall be set to one 13 0b 1 = Device detected CBLID-above VIH 0 = device detected CBLID-below VIL Device 1 hardware reset result Device 0 shall clear these bits to zero Device 1 shall set these bits as follows: 12 0b Reserved 11 0b 0 = Device 1 did not assert PDIAG1 = Device 1 asserted PDIAG- 10-9 These bits indicate how Device 1 determined the device number: 00 = Reserved 01 = a jumper was used 10 = the CSEL signal was used 11 = some other method was used or the method is unknown 8 0b Shall be set to one Device 0 hardware reset result. Device 1 shall clear these bits to zero. Device 0 shall set these bits as follows: 94 7 0b Reserved 6 0b 0 = Device 0 does not respond when Device 1 is selected. 1 = Device 0 responds when Device 1 is selected. 5 0b 0 = Device 0 did not detect the assertion of DASP1 = Device 0 detected the assertion of DASP- 4 0b 0 = Device 0 did not detect the assertion of PDIAG1 = Device 0 detected the assertion of PDIAG- 3 0b 0 = Device 0 failed diagnostics. 1 = Device 0 passed diagnostics. 2-1 00b These bits indicate how Device 0 determined the device number: 00 = Reserved 01 = a jumper was used 10 = the CSEL signal was used 11 = some other method was used or the method is unknown 0 0b Shall be set to one 00h Vendor's recommended acoustic management value V 00h Current automatic acoustic management value (O)V 0000h 15-8 7-0 95 PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN F Stream Minimum Request Size 25 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description 96 (O)V 0000h Streaming Transfer Time - DMA 97 (O)V 0000h Streaming Access Latency - DMA and PIO 98 (O)F 100 V 0000h 0000h 104 (O)V 0000h Streaming Transfer Time - PIO 105 ( )F 0008h Maximum number of 512-byte blocks of LBA Range Entries per DATA SET MANAGEMENT command 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = Device has multiple logical sectors per physical sector 1 = Device logical sector longer than 256 words 106 Physical sector size/logical sector size 12 F 0b 11-4 F 00000000b 3-0 F 0011b 2^x logical sectors per physical sector (O)F 0000h Inter-seek delay for ISO-7779 acoustic testing in microseconds 0101b NAA (3-0) 107 108 15-12 F 11-0 109 Streaming Performance Granularity (98-99) Varies by capacity Maximum user LBA for 48-bit Address feature set 15-4 F 3-0 Reserved 000000001010b IEEE OUI (23-12) 000001110101b IEEE OUI (11-0) Varies Unique ID (35-32) 110 (M)F Varies 5-0 Unique ID (31-16) 111 (M)F Varies Unique ID (15-0) 112 (O)F 0000h 0000h 0000h 0000h 116 (O)V 0000h 117 (O)F 0000h 0000h PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Reserved for 12- bit word-wide name extension to 128 bits Reserved for INCITS TR-37-2004 Words per Logical Sector 26 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 119 Description Commands and feature sets supported (continued from words 84-82) 15 F 0b Shall be cleared to zero Shall be set to one 14 F 1b 13-8 F 00000000b 7 F 0b 1 = Extended Power Conditions feature set is supported 6 F 0b 1 = Extended Status Reporting feature set is supported 5 F 0b 1 = Free-fall control feature set is supported 4 F 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is supported 3 F 1b 1 = READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported 2 F 1b 1 = The WRITE UNCORRECTABLE EXT command is supported 1 F 1b 1 = The Write-Read-Verify feature set is supported 0 F 0b Reserved for DDT 120 Reserved Commands and feature sets supported or enabled (continued from words 87-85) 15 0b Shall be cleared to zero Shall be set to one 14 1b 13-6 00000000b 5 0b 1 = Free-fall control feature set is enabled 4 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is supported 3 1b 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported 2 1b 1 = The WRITE UNCORRECTABLE EXT command is supported 1 0b 1 = The Write-Read-Verify feature set is enabled 0 0b 1= Feature set "Disable Data Transfer After Error Detection" is enabled 0 = Feature set "Disable Data Transfer After Error Detection" is disabled 121 F 0000h 0000h 0000h 0000h 0000h 0000h 127 (O) 0000h PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN Reserved Reserved for expanded supported and enabled settings Obsolete 27 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 128 Security status 15-9 F 0000000b Reserved 8 V 0b Security level 0 = High, 1 = Maximum 7-6 F 00b Reserved 5 F 1b 1 = Enhanced security erase supported 4 V 0b 1 = Security count expired 3 V 0b 1 = Security frozen 2 V 0b 1 = Security locked 1 V 0b 1 = Security enabled 0 F 1b 1 = Security supported ( )X Vendor specific data 129-159 160 Vendor specific CFA power mode 1 15 F 0b Word 160 supported 14 F 0b Reserved 13 F 0b CFA power mode 1 is required for one or more commands implemented by the device 12 V 0b CFA power mode 1 disabled 11-0 F 000000000000b X 0000h 0000h 0000h 0000h 0000h 0000h 0000h 15-4 F 000h 3-0 F 3h 161 168 Description 169 Maximum current in ma Reserved for assignment by the CompactFlash Association Reserved Device Nominal Form Factor DATA SET MANAGEMENT command support 15-1 F 0 F 1b 170 F 0000h 0000h 0000h 0000h Additional product identifier 174 F 0000h 0000h Reserved 176 (O)V Varies PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 000000000000000 Reserved b 1 = The Trim bit in the DATA SET MANAGEMENT command is supported Current media serial number (60 ASCII characters) 28 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 206 Description SCT Command Transport 15-12 X 0000b 11-6 F 000000b 5 F 1b SCT Command Transport Data Tables supported 4 F 1b SCT Command Transport Features Control supported 3 F 0b SCT Command Transport Error Recovery Control supported 2 F 1b SCT Command Transport Write Same supported 1 F 0b Obsolete 0 F 1b SCT Command Transport supported ( )F 0000h 0000h 207 209 (O) Vendor-specific Reserved Reserved for CE-ATA Alignment of logical blocks within a larger physical block 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13-0 F 00000000000000b Logical sector offset within the first physical sector where the first logical sector is placed 210 (O)V 0000h 0000h Write-Read-Verify Sector Count Mode 3 Only 212 (O)F 0000h 0001h Verify Sector Count Mode 2 Only 214 (O) NV Cache Capabilities 15-12 F 0000b NV Cache feature set version 11-8 F 0000b NV Cache Power Mode feature set version 7-5 F 000b Reserved 4 V 0b 1 = NV Cache feature set enabled 3-2 F 00b Reserved 1 V 0b 1 = NV Cache Power Mode feature set enabled 0 F 0b 1 = NV Cache Power Mode feature set supported 215 (O)V 0000h NV Cache Size in Logical Blocks (LSW) 216 (O)V 0000h NV Cache Size in Logical Blocks (MSW) 217 (M)F 0001h Nominal media rotation rate (ATA8-ACS 1699-D Revision 6) 218 (O)V 0000h Reserved 219 220 NV Cache Options 15-8 F 00h Reserved 7-0 F 00h Device Estimated Time to Spin Up in Seconds 15-8 F 00h Reserved 7-0 V 00h Write-Read-Verify feature set current mode 221 PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 0000h Reserved 29 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Device ID Table 13: Identify Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 222 Description Transport Major revision number. 0000h or FFFFh = device does not report version 15-12 0001b Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved Parallel (Type = 0) Serial (Type = 1) 11-7 000000b 6 1b Supports SATA Rev 3.1 5 1b Supports SATA Rev 3.0 4 1b Supports SATA Rev 2.6 3 1b Supports SATA Rev 2.5 2 1b Supports SATA II: Extensions 1 1b Supports SATA 1.0a 0 1b Supports ATA8-APT ATA8-AST Reserved Reserved 223 (M)F 0000h 224 ( )F 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 234 (O)F 0001h Minimum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3 235 00FFh Maximum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3 236 0000h 0000h 0000h 0000h 0000h 0000h 0000h 243 4000h 244 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 255 (M)F Transport Minor revision number Reserved for CE-ATA Reserved Bit 14 = 1; Supports FDE security features Reserved Integrity word 15-8 varies Checksum 7-0 A5h Signature Note: PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 1. F = The content of the word is fixed and does not change. V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device. X = The content of the word may be fixed or variable. R = The content of the word is reserved and will be zero. 30 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Commands Commands Table 14: Supported ATA Command Set See ATA-8 standard for command details Command Name Command Code (hex) CHECK POWER MODE 98h or E5h DEVICE CONFIGURATION RESTORE B1h/C1h DEVICE CONFIGURATION FREEZE LOCK B1h/C3h DEVICE CONFIGURATION IDENTIFY B1h/C1h DEVICE CONFIGURATION SET B1h/C3h DOWNLOAD MICROCODE 92h EXECUTE DEVICE DIAGNOSTIC 90h FLUSH CACHE E7h FLUSH CACHE EXT EAh IDENTIFY DEVICE ECh IDLE E3h or 97h IDLE IMMEDIATE E1h or 95h INITIALIZE DEVICE PARAMETERS 91h NOP 00h READ BUFFER E4h READ DMA (with retry) C8h READ DMA (without retry) C9h READ DMA EXT 25h READ FPDMA QUEUED 60h READ LOG EXT 2Fh READ MULTIPLE C4h READ MULTIPLE EXT 29h READ NATIVE MAX ADDRESS F8h READ NATIVE MAX ADDRESS EXT 27h READ SECTOR(S) EXT 24h READ SECTOR(S) (with retry) 20h READ SECTOR(S) (without retry) 21h READ VERIFY SECTOR EXT 42h READ VERIFY SECTOR(S) (with retry) 40h RECEIVE FPDMA QUEUED 65h SANITIZE DEVICE B4h SCT WRITE SAME 02h/0001h 02h/0002h 02h/0101h 02h/0102h SCT RETURN ERROR RECOVERY CONTROL 030h/01h SCT SET ERROR RECOVERY CONTROL 03h/01h PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Commands Table 14: Supported ATA Command Set (Continued) See ATA-8 standard for command details Command Name Command Code (hex) SCT SET FEATURE CONTROL 04h/01h SCT RETURN FEATURE CONTROL 04h/02h SCT RETURN FEATURE OPTION FLAG 04h/03h SCT RETURN SCT DATA TABLE 05h/01h SECURITY DISABLE PASSWORD F6h SECURITY ERASE PREPARE F3h SECURITY ERASE UNIT F4h SECURITY FREEZE LOCK F5h SECURITY SET PASSWORD F1h SECURITY UNLOCK F2h SEEK 7xh SEND FPDMA QUEUED 64h SET FEATURES EFh SET MAX ADDRESS F9h SET MAX - FREEZE LOCK F9h/04h SET MAX - LOCK F9h/02h SET MAX ADDRESS EXT 37h SET MULTIPLE MODE C6h SET MAX - SET PASSWORD F9h/01h SET MAX - UNLOCK F9h/03h SLEEP E6h or 99h SMART DISABLE OPERATIONS B0h/D9h SMART ENABLE OPERATIONS B0h/D8h SMART ENABLE/DISABLE AUTOSAVE B0h/D2h SMART EXECUTE OFF-LINE IMMEDIATE B0h/D4h SMART READ DATA B0h/D0h SMART READ LOG SECTOR B0h/D5h SMART RETURN STATUS B0h/DAh SMART WRITE LOG B0h/D6h STANDBY E2h or 96h STANDBY IMMEDIATE E0h or 94h TRUSTED NON-DATA 5Bh TRUSTED RECEIVE 5Ch TRUSTED RECEIVE DMA 5Dh TRUSTED SEND 5Eh TRUSTED SEND DMA 5Fh WRITE BUFFER E8h PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 32 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Commands Table 14: Supported ATA Command Set (Continued) See ATA-8 standard for command details Command Name Command Code (hex) WRITE DMA (with retry) CAh WRITE DMA (without retry) CBh WRITE DMA EXT 35h WRITE DMA FUA EXT 3Dh WRITE FPDMA QUEUED 61h WRITE LOG EXT 3Fh WRITE MULTIPLE C5h WRITE MULTIPLE EXT 39h WRITE MULTIPLE FUA EXT CEh WRITE SECTOR(S) (with retry) 30h WRITE SECTOR(S) EXT 34h WRITE UNCORRECTABLE EXT 45h PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Compliance Compliance Micron SSDs comply with the following: * * * * * * * * * * * RoHS "green" CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003 FCC: CFR Title 47, Part 15, ICES-003, all Class B UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Edition BSMI (Taiwan): approval to CNS 13438 C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22 KCC RRL (Korea): approval to KCC MU2-C30025, KCC MU2-C30018 Class B W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations may apply to customers who place these products in the markets where WEEE is enforced. TUV (Germany): approval to IEC60950/EN60950 VCCI IC (Canada): - This Class B digital apparatus complies with Canadian ICES-003. - Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. FCC Rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: * Reorient or relocate the receiving antenna. * Increase the separation between the equipment and the receiver. * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. * Consult the dealer or an experienced radio/TV technician for help. PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Package Dimensions Package Dimensions Figure 5: M.2 Type 2260 Package 2.00mm 0.15 0.079in 0.006 (TYP) Pin 1 Pin 75 5.50mm 0.10 0.217in 0.004 DIA (plated GND pad) 4.00mm MIN 0.157in 1.50mm MAX 0.059in 0.80mm 0.08 0.031in 0.003 1.50mm MAX 0.059in 5.20mm MIN 0.205in 1.20mm 0.05 DIA slot thru 0.047in 0.002 (2 PLCS) 1.00mm 0.10 0.039in 0.004 4.00mm 0.15 0.157in 0.006 (2 PLCS) 1.00mm RAD thru 0.039in (2 PLCS) 6.00mm 0.10 DIA 0.236in 0.004 (plated GND pad) Pin 74 6.125mm 0.150 0.2411in 0.0059 22.00mm 0.15 0.866in 0.006 19.85 0.15 0.781in 11.00mm 0.433in for reference only Pin 2 +0.10 3.50mm 0.08 DIA thru 0.138in 0.003 60.00 0.15 2.362in 0.006 PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 5.625mm 0.150 0.221in 0.0059 35 3.50mm -0.15 +0.004 0.138in -0.006 2.50mm 0.15 0.098in 0.006 (TYP) Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Package Dimensions Figure 6: M.2 Type 2280 Package 2.00mm 0.15 0.079in 0.006 (TYP) Pin 1 Pin 75 5.50mm 0.10 0.217in 0.004 DIA (plated GND pad) 4.00mm MIN 0.157in 1.50mm MAX 0.059in 0.80mm 0.08 0.031in 0.003 4.00mm 0.15 0.157in 0.006 (2 PLCS) 1.00mm 0.10 0.039in 0.004 6.00mm 0.10 DIA 0.236in 0.004 (plated GND pad) 1.20mm 0.05 DIA slot thru 0.047in 0.002 (2 PLCS) 1.00mm 0.039in RAD thru (2 PLCS) Pin 74 6.125mm 0.150 0.2411in 0.0059 22.00mm 0.15 0.866in 0.006 19.85mm 0.15 0.781in 0.006 11.00mm 0.433in for reference only Pin 2 3.50mm 0.08 DIA THRU 0.138in 0.003 80.00mm 0.15 3.150in 0.006 PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 36 5.625mm 0.150 0.221in 0.0059 3.50mm +0.10 -0.15 0.138in +0.004 -0.006 2.50mm 0.15 0.098in 0.006 (TYP) Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD References References * Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available at www.sata-io.org * SATA 3.2 GOLD * ATA-8 ACS3 (T13/2161-D, Revision 4k) * TCG Storage Security Subsystem Class Opal; Specification 2.00 Revision 1.00, Feb 24, 2012 * TCG Core Specification; Specification 2.00 Revision 2.00, Nov 4, 2011 * TCG Storage Interface Interactions: Specification Version 1.02 Revision 1.00 30 December, 2011 * IEEE-1667: "Standard Protocol for Authentication in Host Attachments of Transient Storage Devices" PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 37 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved. M600 M.2 Type 2260/2280 NAND Flash SSD Revision History Revision History Rev. C - 9/14 * * * * * Updated Endurance: Total bytes written in Feature up to 144 to 300TB. Updated Part Number Chart. Updated table 7: Drive Lifetime and notes in Endurance. Added Dynamic Write Acceleration. Updated Adaptive Thermal Monitoring. * * * * * * Updated Operating temperature note on page 1. Updated Part Number Chart. Updated values and notes in the Drive Performance table. Updated notes in the Drive Lifetime - Client Computing table. Updated values and notes in the SATA Power Consumption table. Updated notes in the Maximum Ratings table. Rev. B - 7/14 Rev. A - 03/14 * Initial release. 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000 www.micron.com/products/support Sales inquiries: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. PDF: 09005aef859ad464 m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 38 Micron Technology, Inc. reserves the right to change products or specifications without notice. (c) 2014 Micron Technology, Inc. All rights reserved.