M600 M.2 Type 2260/2280 NAND Flash
SSD
MTFDDAV128MBF, MTFDDAV256MBF, MTFDDAV512MBF,
MTFDDAY128MBF, MTFDDAY256MBF, MTFDDAY512MBF
Features
Micron® 16nm MLC NAND Flash
RoHS-compliant package
SATA 6 Gb/s interface
TCG/Opal 2.0-compliant self-encrypting drive
(SED)
Compatible with Microsoft eDrive®
Hardware-based AES-256 encryption engine
ATA modes supported
PIO mode 3, 4
Multiword DMA mode 0, 1, 2
Ultra DMA mode 0, 1, 2, 3, 4, 5, 6
Industry-standard, 512-byte sector size support
Device Sleep (DEVSLP), extreme low power mode
Native command queuing support with 32-com-
mand slot support
ATA-8 ACS3 command set compliant
ATA security feature command set and password
login support
Secure erase (data page) command set: fast and se-
cure erase
Sanitize device feature set support
Self-monitoring, analysis, and reporting technology
(SMART) command set
Dynamic write acceleration
Adaptive thermal monitoring
Power loss protection for data-at-rest
Performance1, 2
PCMark® Vantage (HDD test suite score): up to
87,000
Sequential 128KB READ: up to 560 MB/s
Sequential 128KB WRITE: up to 510 MB/s
Random 4KB READ: up to 100,000 IOPS
Random 4KB WRITE: up to 88,000 IOPS
READ/WRITE latency: 120µs/30µs (TYP)
Reliability
MTTF: 1.5 million device hours3
Static and dynamic wear leveling
Uncorrectable bit error rate (UBER): <1 sector
per 1015 bits read
Low power consumption
150mW TYP4
Endurance: Total bytes written (TBW)
Up to 300TB
Capacity (unformatted): 128GB, 256GB, 512GB
Mechanical
M.2 "Socket 2" connector: 3.3V ±5%
Type 2260: 60mm x 22mm x 3.6mm
Type 2280: 80mm x 22mm x 2.3mm
Weight: 10g (MAX)
Secure firmware update with digitally signed firm-
ware image
Operating temperature
Commercial (0°C to +70°C)5
Notes: 1. Typical I/O performance numbers as meas-
ured fresh-out-of-box (FOB) using Iometer
with a queue depth of 32 and write cache
enabled.
2. 4KB transfers used for READ/WRITE latency
values.
3. The product achieves a mean time to failure
(MTTF) based on population statistics not
relevant to individual units.
4. Active average power measured during exe-
cution of MobileMark® with DIPM (device-
initiated power management) enabled.
5. Temperature measured by SMART attribute
194.
Warranty: Contact your Micron sales representative
for further information regarding the product,
including product warranties.
M600 M.2 Type 2260/2280 NAND Flash SSD
Features
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Products and specifications discussed herein are subject to change by Micron without notice.
Part Numbering Information
Micron’s M600 SSD is available in different configurations and densities. The chart below is a comprehensive list
of options for the M600 series devices; not all options listed can be combined to define an offered product. Visit
www.micron.com for a list of valid part numbers.
Figure 1: Part Number Chart
MT FD D AV 128 M BF - 1 AN 1 ES
Micron Technology
Product Family
FD = Flash drive
Drive Interface
D = SATA 6.0 Gb/s
Drive Form Factor
AK = 2.5-inch (7mm)
AT = mSATA
AV = M.2 (80mm x 22mm 2.3mm)
AY = M.2 (60mm x 22mm 3.5mm)
Drive Density
064 = 64GB
128 = 128GB
256 = 256GB
512 = 512GB
1T0 = 1024GB
NAND Flash Type
M = MLC
Product Family
BF = M600
Production Status
Blank = Production
ES = Engineering sample
MS = Mechanical sample
Customer Designator
YY = Standard
Feature Set
AA = Contact factory
AB = Standard
AC = Contact factory
ZZ = Blank
Extended Firmware Features
Z = Non-Encrypted
1 = Contact factory
2 = SED (self-encrypting drive)
Sector Size
1 = 512 byte
NAND Flash Component
AN = 128Gb, MLC, x8, 3.3V (16nm)
BOM Revision
For example:
1 = 1st generation
2 = 2nd generation
2 AB YY
M600 M.2 Type 2260/2280 NAND Flash SSD
Features
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
General Description
Micron’s solid state drive (SSD) uses a single-chip controller with a SATA interface on
the system side and 8-channels of Micron NAND Flash internally. Packaged in an HDD
replacement enclosure, the SSD integrates easily in existing storage infrastructures.
The SSD is designed to use the SATA interface efficiently during both READs and
WRITEs while delivering bandwidth-focused performance. SSD technology enables en-
hanced boot times, faster application load times, reduced power consumption, and ex-
tended reliability.
The M.2 Type 2260 and 2280 are caseless form factors ideally suited for ultrathin, mo-
bile computing applications, which require mass storage in a very small footprint.
The self-encypting drive (SED) features a FIPS-compliant, AES-256 encryption engine,
providing hardware-based, secure data encryption, with no loss of SSD performance.
This SED follows the TCG/Opal specification for trusted peripherals.
When TCG/Opal features are not enabled, the device can perform alternate data en-
cryption by invoking the ATA security command-set encryption features, to provide full-
disk encryption (FDE) managed in the host system BIOS. TCG/Opal and ATA security
feature sets cannot be enabled simultaneously.
The data encryption is always running; however, encryption keys are not managed and
the data is not secure until either TCG/Opal or ATA security feature sets are enabled.
Figure 2: Functional Block Diagram
NAND
SATA
NAND
NAND
NAND
SSD
controller
DRAM
buffer
NAND
M600 M.2 Type 2260/2280 NAND Flash SSD
General Description
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Logical Block Address Configuration
The drive is set to report the number of logical block addresses (LBA) that will ensure
sufficient storage space for the specified capacity. Standard LBA settings, based on the
IDEMA standard (LBA1-03), are shown below.
Table 1: Standard LBA Settings
Capacity
Total LBA Max LBA
User Available
Bytes
Decimal Hexadecimal Decimal Hexadecimal (Unformatted)
128GB 250,069,680 EE7C2B0 250,069,679 EE7C2AF 128,035,676,160
256GB 500,118,192 1DCF32B0 500,118,191 1DCF32AF 256,060,514,304
512GB 1,000,215,216 3B9E12B0 1,000,215,215 3B9E12AF 512,110,190,592
Physical Configuration
Table 2: Dimensions and Weight
Specification
Value
UnitNom Max
Height 3.58 mm
Width 22.00 mm
Length 60.00 or 80.00 mm
Unit weight 10 g
Insertion rating 10 insert/remove cycles
Interface Connectors
Figure 3: SSD Interface Connections
P1
P75
P67
P57 P21
P11
P74
P2
P10
P20 P58
P68
Primary side Secondary side
M600 M.2 Type 2260/2280 NAND Flash SSD
Logical Block Address Configuration
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 3: Signal Assignments
Primary Side Secondary Side
Pin # Signal Name Description Pin # Signal Name Description
1 GND (PRESENCE) Ground 2 3V3 +3.3V
3 GND Ground 4 3V3 +3.3V
5 GND No connect 6 Reserved No connect
7 DNU No connect 8 Reserved No connect
9 DNU Ground 10 DAS/DSS Drive activity (host
LED)
11 GND Ground Key
Key 20 Reserved No connect
21 GND (Direct to P69) No connect 22 Reserved No connect
23 DNU No connect 24 Reserved No connect
25 DNU No connect 26 Reserved No connect
27 GND Ground 28 Reserved No connect
29 Reserved No connect 30 Reserved No connect
31 Reserved No connect 32 Reserved No connect
33 GND Ground 34 Reserved No connect
35 Reserved No connect 36 Reserved No connect
37 Reserved No connect 38 DEVSLP Device sleep
39 GND Ground 40 Reserved No connect
41 SATA +B SATA B differential
pair
42 Reserved No connect
43 SATA -B 44 Reserved No connect
45 GND Ground 46 Reserved No connect
47 SATA -A SATA A differential
pair
48 Reserved No connect
49 SATA +A 50 Reserved No connect
51 GND Ground 52 Reserved No connect
53 Reserved No connect 54 Reserved No connect
55 Reserved No connect 56 Reserved Vendor use
57 GND Ground 58 Reserved Vendor use
Key Key
67 DNU No connect 68 SUSCLK No connect
69 PEDET Ground 70 3V3 +3.3V
71 GND Ground 72 3V3 +3.3V
73 GND Ground 74 3V3 +3.3V
75 GND Ground
M600 M.2 Type 2260/2280 NAND Flash SSD
Interface Connectors
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Performance
Measured performance can vary for a number of reasons. The major factors affecting
drive performance are the capacity of the drive and the interface of the host. Addition-
ally, overall system performance can affect the measured drive performance. When
comparing drives, it is recommended that all system variables are the same, and only
the drive being tested varies.
Performance numbers will vary depending on the host system configuration.
For SSDs designed for the client computing market, Micron specifies performance in
fresh-out-of-box (FOB) state. Data throughput measured in "steady state" may be lower
than FOB state, depending on the nature of the data workload.
For a description of these performance states and of Micron's best practices for per-
formance measurement, refer to Micron's technical marketing brief "Best Practices for
SSD Performance Measurement"
(www.micron.com/products/solid-state-storage/).
Table 4: Drive Performance
Capacity 128GB 256GB 512GB
UnitInterface Speed 6 Gb/s 6 Gb/s 6 Gb/s
PCMark Vantage 87,000 87,000 87,000 HDD score
Sequential read (128KB transfer) 600 600 600 MB/s
Sequential write (128KB transfer) 350 500 500 MB/s
Random read (4KB transfer) 90,000 100,000 100,000 IOPS
Random write (4KB transfer) 88,000 88,000 88,000 IOPS
READ latency (TYP) 120 120 120 µs
WRITE latency (TYP) 30 30 30 µs
Notes: 1. Performance numbers are maximum values, except as noted.
2. Typical I/O performance numbers as measured using Iometer with a queue depth of 32
and write cache enabled. Fresh-out-of-box (FOB) state is assumed. For performance
measurement purposes, the SSD may be restored to FOB state using the secure erase
command.
3. Iometer measurements are performed on an 20GB span of logical block addresses
(LBAs).
4. 4KB transfers with a queue depth of 1 are used to measure READ/WRITE latency values
with write cache enabled.
5. System variations will affect measured results. For comparison, PCMark scores are meas-
ured with the SSD as a secondary drive in a two-drive system. When measured as an OS
drive, system overhead can cause lower scores.
M600 M.2 Type 2260/2280 NAND Flash SSD
Performance
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Reliability
Micron’s SSDs incorporate advanced technology for defect and error management.
They use various combinations of hardware-based error correction algorithms and
firmware-based static and dynamic wear-leveling algorithms.
Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is de-
fined as data that is reported as successfully programmed to the SSD but when it is read
out of the SSD, the data differs from what was programmed.
Table 5: Uncorrectable Bit Error Rate
Uncorrectable Bit Error Rate Operation
<1 sector per 1015 bits read READ
Mean Time To Failure
Mean time to failure (MTTF) for the SSD can be predicted based on the component reli-
ability data using the methods referenced in the Telcordia SR-332 reliability prediction
procedures for electronic equipment.
Table 6: MTTF
Capacity MTTF (Operating Hours)1
64GB 1.5 million
128GB 1.5 million
256GB 1.5 million
512GB 1.5 million
Note: 1. The product achieves a mean time to failure (MTTF) of 1.5 million hours, based on popu-
lation statistics not relevant to individual units.
M600 M.2 Type 2260/2280 NAND Flash SSD
Reliability
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Endurance
Endurance for the SSD can be predicted based on the usage conditions applied to the
device, the internal NAND component cycles, the write amplification factor, and the
wear-leveling efficiency of the drive. The tables below show the drive lifetime for each
SSD capacity by client computing and sequential input and based on predefined usage
conditions.
Table 7: Drive Lifetime – Client Computing
Capacity Drive Lifetime (Total Bytes Written)
128GB 100TB
256GB 200TB
512GB 300TB
Notes: 1. Total bytes written validated with the drive 90% full.
2. SSD volatile write cache is enabled.
3. Access patterns used during reliability testing are 25% sequential and 75% random and
consist of the following: 50% are 4 KiB; 40% are 64 KiB; and 10% are 128 KiB.
4. Host workload parameters, including write cache settings, I/O alignment, transfer sizes,
randomness, and percent full, that are substantially different than the described notes
may result in varied endurance results.
5. GB/day can be calculated by dividing the total bytes written value by (365 × number of
years). For example: 100 TB/5 years/365 days = 54 GB/day for 5 years.
M600 M.2 Type 2260/2280 NAND Flash SSD
Reliability
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Electrical Characteristics
Environmental conditions beyond those listed may cause permanent damage to the de-
vice. This is a stress rating only, and functional operation of the device at these or any
other conditions above those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods
may affect reliability.
Table 8: SATA Power Consumption
Capacity
Device Sleep
Typical Idle Average Active Average
Active Maximum
(128KB transfer) Unit
128GB 2 70 150 3600 mW
256GB 2 70 150 4400 mW
512GB 2 70 150 4700 mW
Notes: 1. Data taken at 25°C using a 6 Gb/s SATA interface.
2. Active average power measured while running MobileMark Productivity Suite.
3. DIPM (device-initiated power management) enabled. DIPM Slumber supported.
4. Active maximum power is an average power measurement performed using Iometer
with 128KB sequential write transfers.
Table 9: Maximum Ratings
Parameter/Condition Symbol Min Max Unit Notes
Voltage input 3V3 3.14 3.46 V
Operating temperature TC0 70 °C 1
Non-operating temperature –40 85 °C
Rate of temperature change 20 °C/hour
Relative humidity (non-condensing) 5 95 %
Note: 1. Operating temperature is best measured by reading the SSD's on-board temperature
sensor, which is recorded in SMART attribute 194 (or 0xC2).
Table 10: Shock and Vibration
Parameter/Condition Specification
Non-operating shock 1500G/0.5ms
Non-operating vibration 5–800Hz @ 3.13G
M600 M.2 Type 2260/2280 NAND Flash SSD
Electrical Characteristics
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Dynamic Write Acceleration
Dynamic write acceleration optimizes SSD performance for typical client-computing
environments, where WRITE operations tend to occur in bursts of commands with idle
time between these bursts.
Capacity for accelerated performance is derived from the adaptive usage of the SSD's
native NAND array, without sacrificing user-addressable storage. Recent advances in
Micron NAND technology enable the SSD firmware to achieve acceleration through on-
the-fly mode switching between SLC and MLC modes to create a high-speed SLC pool
that changes in size and location with usage conditions.
During periods of idle time between write bursts, the drive may free additional capacity
for accelerated write performance. The amount of accelerated capacity recovered dur-
ing idle time depends on the portion of logical addresses that contain user data and
other runtime parameters. In applications that do not provide sufficient idle time, the
device may need to perform SLC-to-MLC data migration during host activity.
Under accelerated operation, write performance may be up to 2.8 times higher than
non-accelerated operations. Power consumption per-byte written is lower during accel-
erated operation, which may reduce overall power consumption and heat production.
The following table shows the form factors and capacities that feature dynamic write
acceleration.
Table 11: Dynamic Write Acceleration – Capacities and Form Factors
M600 Form Factors 128GB 256GB 512GB 1024GB
2.5" 7mm on on off off
M.2 2280, single-sided on on on
M.2 2260, double-sided on on on
mSATA on on on
M600 M.2 Type 2260/2280 NAND Flash SSD
Dynamic Write Acceleration
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Adaptive Thermal Monitoring
The device features adaptive thermal monitoring. While most host computers exhibit
operating environments that keep an SSD running in the range of 40°C to 45°C, adap-
tive thermal monitoring enables the SSD device to operate in a wide variety of environ-
ments by helping to prevent the host computer from running at excessive temperatures.
Adaptive thermal monitoring reduces total SSD power consumption by the device con-
troller, as well as the NAND media, by injecting time-based delays between internal
processing of media commands when the device temperature reaches 75 °C. The delay
times used are bound to the microsecond range, and are based on a proportional and
differential control equation of the general form shown here.
Figure 4: Adaptive Thermal Monitoring Control Equation
u(t) = Kp × Tp(t) + Kd × dTd
dt
The delay-control equation is tuned for a steady-state temperature target, which has
been designed as an optimum balance of hardware temperature tolerances and drive
performance. Steady-state temperature targets are hardware-configuration dependant,
and may range from 80 °C to 84 °C. Temperatures below the intended steady-state target
will not produce a proportional component to delay, but may produce a differential
component based on the current rate of temperature change according to the control
equation. When the feature is active, DRAM refresh rates are also adjusted to improve
data integrity and stability while operating outside of temperature specifications.
When the device temperature falls below 73 °C, normal operation will continue without
induced delays. If temperature continues to rise above the temperature target and ex-
ceeds a hardware-dependant critical threshold, the device will abort host commands to
prevent component damage. The critical threshold values have a 6 °C margin on top of
target threshold, and range between 86 °C and 90 °C.
Device temperature values used by the adaptive thermal monitoring feature are based
on an internal temperature sensor located on the device PCB, and may differ from case
or package temperatures as measured by thermocouple. Device temperature is accessi-
ble through SMART attribute 194, though usage of the SMART feature is not necessary
for adaptive thermal monitoring functionality.
Adaptive thermal monitoring does not change the current negotiated speed of the SATA
bus, nor require or cause any new commands to be issued on the SATA bus. Rated-
throughput performance is not guaranteed at any point above the maximum specified
operating temperature.
M600 M.2 Type 2260/2280 NAND Flash SSD
Adaptive Thermal Monitoring
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
TCG/Opal Support
Table 12: TCG/Opal Support Parameters
Property Supported? Comments
TCG Storage Specifications
OPAL: TCG Storage Security SubSystem
Class
Specification 2.00 Revision 1.00, Feb 24, 2012
TCG Core Specification Specification 2.00 Revision 2.00, Nov 4, 2011
TCG Storage Interface Interactions Specifi-
cation
TCG Reference
Specification
Specification Version 1.02 Revision 1.00 30 Decem-
ber, 2011
OPAL SSC 1.00 (backward compatibility) Not supported
OPAL SSC Additional Feature Set Specification
Additional DataStore Table Supported Specification 1.00 Revision 1.00, Feb 24, 2012
Single User Mode Supported Specification 1.00 Revision 1.00, Feb 24, 2012
TCG Storage Protection Mechanisms for
Secrets
Supported Specification Version 1.00 Revision 1.07 17 August,
2011
PSID – Physical Presence SID Supported Specification Version 1.00 Committee Draft Revi-
sion 1.05 February 9, 2011
GUDID (Globally Unique Serial Number) Supported Mandatory GUDID Proposal 11/03/2011 (Microsoft)
SID Authority Disable Supported SID Authority Disable Proposal 9/26/2011 (Micro-
soft)
Modifiable CommonName Columns Supported Modifiable CommonName Columns Proposal
7/22/2010 (Microsoft)
OPAL SSC Feature Set – Specific List
ALL OPAL Mandatory Features Supported
Close Session (optional) Supported Allows Tper to notify the host it has aborted a ses-
sion
Restricted Command & Table (optional) Not Supported The interface control template enables TPer control
over selected interface commands; the benefit is
the reduction of undesired side effects
Type Table (not required) Not Supported
Activate Method Supported
Revert Method Supported
Revert SP Method Supported
Activate Method Within Transactions Not Supported As per OPAL, this behavior is out of the scope
Revert Method within Transactions Not Supported As per OPAL, this behavior is out of the scope
Revert SP Method within Transactions Not Supported As per OPAL, this behavior is out of the scope
Creation/Deletion of Tables/Rows after
Manufacturing
Not Supported As per OPAL, this behavior is out of the scope
Tper Feature
COM ID Management Support Not Supported Dynamic COM ID allocation & management not
supported
Buffer Management Support Not Supported Flow control
M600 M.2 Type 2260/2280 NAND Flash SSD
TCG/Opal Support
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 12: TCG/Opal Support Parameters (Continued)
Property Supported? Comments
ACK/NACK Support Not Supported Session reliability
Async Support Not Supported Asynchronous protocol support with multiple com-
mands per session
Geometry Reporting Feature
ALIGN Supported OPAL 2.0 (only)
Logical Block Size 512 bytes Logical block size = 512 Bytes
Alignment Granularity 4096 Bytes Page or Descriptor size <<Minimum AES LU size>>
Lowest Aligned LBA 0
OPAL SSC V2.00 Feature Descriptor
Base COM ID 0x1000 0x1000-0xFFFF defined for COM ID management
Number of COM IDs 1
Range Crossing Behavior 0 If drive receives a READ or WRITE command that
spans multiple LBA ranges and the LBA ranges are
not locked, then:
1. Process the data transfer, if Range Crossing = 0
2. Terminate the command with “Other Invalid
Command Parameter” if Range Crossing = 1
Number of Locking SP Admin Authorities
Supported
4 As per OPAL 2.0, drive should support at least 4 ad-
min
Number of Locking SP User Authorities
Supported
9 As per OPAL 2.0, drive should support at least 8
users
Initial C_PIN_SID PIN Indicator 0x00 0x00 = The initial C_PIN_SID PIN value is equal to
the C_PIN_MSID PIN value
0xFF = The initial C_PIN_SID PIN value is VU, and
MAY not be equal to the C_PIN_MSID PIN value
OPAL 2.0 (only)
Customer-specific SID – Configurable
Behavior of C_PIN_SID PIN upon Ter Revert 0x00 0x00 = The C_PIN_SID PIN value becomes the value
of the C_PIN_MSID PIN column after successful in-
vocation of revert on the admin SP’s object in the
SP table
0xFF = The C_PIN_SID PIN value changes to a VU
value after successful invocation of revert on the
admin SP’s object in the SP table and MAY not be
equal to the C_PIN_MSID PIN value OPAL 2.0 (only)
DataStore Table Feature
Maximum number of DataStore Tables 9 The maximum number of the DataStore tables that
the TPer supports, including the DataStore table
defined in OPAL SSC 2.0
Maximum total size of DataStore Tables 90MB Specifies the maximum total size in bytes of all of
the DataStore tables that TPer supports, including
the DataStore table defined in OPAL SSC 2.0
DataStore Table Size Alignment 10MB
M600 M.2 Type 2260/2280 NAND Flash SSD
TCG/Opal Support
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 12: TCG/Opal Support Parameters (Continued)
Property Supported? Comments
MBR Table 128MB
Byte Table Access Granularity
Mandatory Write Granularity 1 TPer enforces when the host invokes the set meth-
od on byte tables; it should be less than or equal to
8192; it should be less than or equal to Recommen-
ded Access Granularity, OPAL 2.0 (only)
Recommended Access Granularity 8192 Tper recommends when the host invokes the set or
get method on byte tables; it should be less than or
equal to 8192
Cryptographic Features
AES Key Size 256 Bits AES key is generated by using CTR DRBG algorithm
(FIPS Compliant)
AES Mode CBC IV swapped
Number of Ranges/Band Supported 9
(8 user definable,
1 global range)
Now supporting 8 LBA ranges; range cross read
and write allowed if LBA ranges are unlocked
Re-Encryption Not Supported
Key Management Authentication data required. Conforms to TCG
Storage Protection Mechanisms for Secrets; Specifi-
cation version 1.00, Revision 1.00, 05 March 2012
Crypto Erase Completion Time <1s Yes
Cryptographic Algorithms are Certified by
FIPS-197
Pending
AES 256-Bit CBC/ECB Mode Supported ECB mode used only for generating the random
key by CTR DRBG
CTR DRBG Supported
SHA 256 Supported
RSA 2048 Signature Verification Supported
TPer Communication Properties
Max ComPacket Size 131072 256 sectors (128K)
Max Response ComPacket Size 131072 256 sectors (128K)
Max Packet Size 128512
Max Individual Token Size 123904
Max Packets 1
Max SubPackets 1
Max Sessions 1 Each session requires a set of buffers and variables
Max Transaction Limit 1 Transaction are inside sessions
Max Methods 1 Methods are contained in a transaction
Max Authentications 2
M600 M.2 Type 2260/2280 NAND Flash SSD
TCG/Opal Support
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 12: TCG/Opal Support Parameters (Continued)
Property Supported? Comments
Def Session Timeout Yes The session timeout length (in milliseconds) used
by the TPer by default
IEEE1667
Probe Silo Supported
TCG Storage Silo Supported
Other than Probe and TCG Storage Silo Not Supported
IEEE1667 Major Version TBD As per current draft specification, major and minor
versions are not yet decided
IEEE1667 Minor Version TBD
Maximum P_OUT Transfer Size 131072 256 sectors (128K)
Others
FDE (ATA Security with Key Management) Yes
Secure Firmware Download Supported Firmware image is validated by using SHA256 and
RSA2048 algorithm (FIPS-compliant; certification
pending)
M600 M.2 Type 2260/2280 NAND Flash SSD
TCG/Opal Support
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Device ID
Table 13: Identify Device
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
0 General configuration bit-significant information
15 F 0b 0 = ATA device
14–8 X 0000100b Retired
7 F 0b 1 = Removable media device
6 F 1b 1 = Fixed disk HDD
5–3 X 000b Retired
2 V 0b Response incomplete
1 X 0b Retired
0 F 0b Reserved
1 3FFFh Obsolete
2 F C837h Specific configuration
3 F 0010h Obsolete
4 F 0000h 0000h Retired
6 F 003Fh Obsolete
7 (O)V 0000h 0000h Reserved for assignment by the CompactFlash Association
9 ( )X 0000h Retired
10 (M)F varies Serial number (20 ASCII characters)
20 ( )X 0000h 0000h
0000h
Retired/Obsolete
23 (M)F varies Firmware revision (8 ASCII characters)
27 (M)F varies Model number (40 ASCII characters)
47 15–8 F 80h 80h
7–0 F 10h 00h = Reserved
01h-FFh = Maximum number of logical sectors that shall be
transferred per DRQ data block on READ/WRITE MULTIPLE
commands
48 Trusted Computing feature set options
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13–1 F 0000000000000b Reserved for the Trusted Computing Group
0 F 1b 1=Trusted Computing feature set is support
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
49 Capabilities
15–14 F 00b Reserved for the IDENTIFY PACKET DEVICE command.
13 F 1b 1 = Standby timer values as specified in this standard are
supported
0 = Standby timer values shall be managed by the device
12 F 0b Reserved for the IDENTIFY PACKET DEVICE command.
11 F 1b 1= IORDY supported
0 = IORDY may be supported
10 F 1b 1 = IORDY may be disabled
9 1b 1 = LBA supported
8 F 1b 1 = DMA supported.
7–0 F 00000000b Retired
50 Capabilities
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13–2 F 000000000000b Reserved
1 X 0b Obsolete
0 F 1b Shall be set to one to indicate a vendor specific standby tim-
er value minimum.
51 ( )X 0000h 0000h Obsolete
53 15–3 F 0000000000000b Reserved
2 F 1b 1 = The fields reported in word 88 are valid
0 = the fields reported in word 88 are not valid
1 F 1b 1 = The fields reported in words (70:64) are valid
0 = the fields reported in words (70:64) are not valid
0 X 1b Obsolete
54 ()X 3FFFh 0010h
003Fh FC10h
00FBh
Obsolete
59 15 F 1b 1 = The BLOCK ERASE EXT command is supported
14 F 0b 1 = The OVERWRITE EXT command is supported
13 F 0b 1 = The CRYPTO SCRAMBLE EXT command is supported
12 F 1b 1 = The Sanitize feature set is supported
11–9 F 000b Reserved
8 V 1b 1 = Multiple sector setting is valid
7–0 V 00010000b xxh = Current setting for number of logical sectors that shall
be transferred per DRQ data block on READ/WRITE MULTI-
PLE commands
60–61 M(F) Varies by capacity Total number of user addressable logical sectors
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
62 ()X 0000h Obsolete
63 15–11 F 00000b Reserved
10 V 0b 1 = Multiword DMA mode 2 is selected
0 = Multiword DMA mode 2 is not selected
9 V 0b 1 = Multiword DMA mode 1 is selected
0 = Multiword DMA mode 1 is not selected
8 V 0b 1 = Multiword DMA mode 0 is selected
0 = Multiword DMA mode 0 is not selected
7–3 F 0000b Reserved
2 F 1b 1 = Multiword DMA mode 2 and below are supported
1 F 1b 1 = Multiword DMA mode 1 and below are supported
0 F 1b 1 = Multiword DMA mode 0 is supported
64 15–8 F 0 Reserved
7–0 F 00000011b PIO modes supported
65 F 0078h Minimum Multiword DMA transfer cycle time per word
Cycle time in nanoseconds
66 F 0078h Manufacturer's recommended Multiword DMA transfer cy-
cle time
Cycle time in nanoseconds
67 F 0078h Minimum PIO transfer cycle time without flow control
Cycle time in nanoseconds
68 F 0078h Minimum PIO transfer cycle time with IORDY flow control
Cycle time in nanoseconds
69 F Additional Supported
15 F 0b 1 = CFast Specification Support
14 F 1b 1 = Deterministic read after Trim is supported
13 F 0b 1 = Long Physical Sector Alignment Error Reporting Control
is supported
12 F 0b 1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE
CONFIGURATION SET DMA are supported
11 F 0b 1 = READ BUFFER DMA is supported
10 F 0b 1 = WRITE BUFFER DMA is supported
9 F 0b 1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA
are supported
8 F 0b 1 = DOWNLOAD MICROCODE DMA is supported
7 F 1b Reserved for IEEE-1667
6 F 0b 1 = Optional ATA device 28-bit commands supported
5 F 1b 1 = Read zero after Trim is supported
4 F 1b 1 = Device encrypts all user data
3–0 F 0000b Reserved
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
70 F 0000h Reserved
71 F 0000h 0000h
0000h 0000h
Reserved for the IDENTIFY PACKET DEVICE command
75 Queue depth
15–5 F 00000000000b Reserved
4–0 F 11111b Maximum queue depth - 1
76 Serial ATA capabilities
15 F 0b 1 = Supports READ LOG DMA EXT as equivalent to READ
LOG EXT
14 F 0b 1 = Supports device automatic partial to slumber transitions
13 F 0b 1 = Supports host automatic partial to slumber transitions
12 F 1b Supports Native Command Queuing priority information
11 F 0b Supports Unload while NCQ commands outstanding
10 F 1b Supports Phy event counters
9 F 0b Supports receipt of host initiated interface power manage-
ment requests
8 F 1b Supports native Command Queueing
7–4 F 0000b Reserved for future Serial ATA signaling speed grades
3 F 1b 1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s)
2 F 1b 1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s)
1 F 1b 1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s)
0 F 0b Reserved (set to 0)
77 Serial ATA additional capabilities
15–8 F 00000000b Reserved for future Serial ATA definition
7 F 1b 1 = Supports DEVSLP_to_ReducedPwrState
6 F 1b Supports RECEIVE FPDMA QUEUED and SEND FPDMA
QUEUED commands
5 F 0b Supports NCQ Queue Management Command
4 F 0b Supports NCQ Streaming
3–1 V 010b Coded value indicating current negotiated Serial ATA signal
speed
0 F 0b Shall be cleared to zero
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
78 Serial ATA features supported
15–8 F 000000000b Reserved
7 F 0b 1 = Supports NCQ Autosense
6 F 1b 1 = Supports software settings preservation
5 F 1b 1 = HARDWARE FEATURE CONTROL SUPPORTED bit
4 F 0b 1 = Supports in-order data delivery
3 F 1b 1 = Supports dev initiate interface power management
2 F 1b 1 = Supports DMA Setup Auto-Activate optimization
1 F 0b 1 = Supports non-zero buffer offsets in DMA Setup FIS
0 F 0b Reserved (set to 0)
79 Serial ATA features enabled
15–7 V 000000000b Reserved
6 V 1b 1 = Software settings preservation enabled
5 V 0b 1 = Asynchronous notification enabled
4 V 0b 1 = In-order data delivery enabled
3 V 0b 1 = Device initiating interface power management enabled
2 V 0b 1 = DMA Setup Auto-Activate optimization enabled
1 V 0b 1 = Non-zero buffer offsets in DMA Setup FIS enabled
0 V 0b Reserved (set to 0)
80 Major revision number
15–10 F 000000b Reserved
9 F 1b 1 = Supports ATA8-ACS2
8 F 1b 1 = Supports ATA8-ACS
7 F 1b 1 = Supports ATA/ATAPI-7
6 F 1b 1 = Supports ATA/ATAPI-6
5 F 1b 1 = Supports ATA/ATAPI-5
4 F 1b 1 = Supports ATA/ATAPI-4
3 F 1b Obsolete
2 S 0b Obsolete
1 S 0b Obsolete
0 F 0b Reserved
81 F 0028h Minor revision number
0028h = ATA8-ACS version 6
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
82 Command set supported
15 X 0b Obsolete
14 F 1b 1 = NOP command supported
13 F 1b 1 = READ BUFFER command supported
12 F 1b 1 = WRITE BUFFER command supported
11 X 0b Obsolete
10 F 1b 1 = Host Protected Area feature set supported
9 F 0b 1 = DEVICE RESET command supported
8 F 0b 1 = SERVICE interrupt supported
7 F 0b 1 = Release interrupt supported
6 F 1b 1 = Read look-ahead supported
5 F 1b 1 = Write cache supported
4 F 0b Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3 F 1b 1 = Mandatory Power Management feature set supported
2 F 0b Obsolete
1 F 1b 1 = Security feature set supported
0 F 1b 1 = SMART feature set supported
83 Command set supported
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13 F 1b 1 = FLUSH CACHE EXT command supported
12 F 1b 1 = Mandatory FLUSH CACHE command supported
11 F 1b 1 = Device Configuration Overlay feature set supported
10 F 1b 1 = 48-bit address feature set supported
9 F 0b 1 = Automatic Acoustic Management feature set supported
8 F 1b 1 = SET MAX security extension supported
7 F 0b See Address Offset Reserved Area Boot INCITS TR27:2001
6 F 0b 1 = SET FEATURES subcommand required to spin-up after
power-up
5 F 0b 1 = Power-Up In Standby feature set supported
4 F 0b Obsolete
3 F 1b 1 = Advanced Power Management feature set supported
2 F 0b 1 = CFA feature set supported
1 F 0b 1 = READ/WRITE DMA QUEUED supported
0 F 1b 1 = DOWNLOAD MICROCODE command supported
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
84 Command set/feature supported extension
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12 F 0b Reserved for technical report INCITS TR-37-2004 (TLC)
11 F 0b Reserved for technical report INCITS TR-37-2004 (TLC)
10–9 F 00b Obsolete
8 F 1b 1 = 64-bit word wide name supported
7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported
6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5 F 1b 1 = General Purpose Logging feature set supported
4 F 0b 1 = Streaming feature set supported
3 F 0b 1 = Media Card Pass Through Command feature set suppor-
ted
2 F 0b 1 = Media serial number supported
1 F 1b 1 = SMART self-test supported
0 F 1b 1 = SMART error logging supported
85 Command set/feature enabled.
15 X 0b Obsolete
14 F 1b 1 = NOP command supported
13 F 1b 1 = READ BUFFER command supported
12 F 1b 1 = WRITE BUFFER command supported
11 X 0b Obsolete
10 V 1b 1 = Host Protected Area feature set enabled
9 F 0b 1 = DEVICE RESET command supported
8 V 0b 1 = SERVICE interrupt enabled
7 V 0b 1 = Release interrupt enabled
6 V 1b 1 = Look-ahead enabled
5 V 1b 1 = Write cache enabled
4 F 0b Shall be cleared to zero to indicate that the PACKET feature
set is not supported.
3 F 1b Power Management feature set is enabled
2 F 0b Obsolete
1 V 0b 1 = Security Mode feature set enabled
0 V 1b 1 = SMART feature set enabled
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
86 Command set/feature enabled.
15 1b 1 = Words 120-119 are valid
14 F 0b 1 = Reserved
13 F 1b 1 = FLUSH CACHE EXT command supported
12 F 1b 1 = FLUSH CACHE command supported
11 F 1b 1 = Device Configuration Overlay supported
10 F 1b 1 = 48-bit Address features set supported
9 V 0b 1 = Automatic Acoustic Management feature set enabled
8 F 0b 1 = SET MAX security enabled by SET MAX SET PASSWORD
7 F 0b Reserved for address Offset Reserved Area Boot, INCITS
TR27:2001
6 F 0b 1 = SET FEATURES subcommand required to spin-up after
power-up
5 V 0b 1 = Power-Up In Standby feature set enabled
4 V 0b Obsolete
3 V 1b 1 = Advanced Power Management feature set enabled
2 F 0b 1 = CFA feature set supported
1 F 0b 1 = READ/WRITE DMA QUEUED command supported
0 F 1b 1 = DOWNLOAD MICROCODE command supported
87 Command set/feature enabled/supported
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported
12 V 0b Reserved for technical report- INCITS tr-37-2004 (TLC)
11 V 0b Reserved for technical report- INCITS TR-37-2004 (TLC)
10–9 F 00b Obsolete
8 F 1b 1 = 64-bit word wide name supported
7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported
6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT
commands supported
5 F 1b 1 = General Purpose Logging feature set supported
4 V 0b Obsolete
3 V 0b 1 = Media Card Pass Through Command feature set suppor-
ted
2 V 0b 1 = Media serial number is valid
1 F 1b 1 = SMART self-test supported
0 F 1b 1 = SMART error logging supported
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
88 0b Ultra DMA modes
15 0b Reserved
14 0b 1 = Ultra DMA mode 6 is selected
0 = Ultra DMA mode 6 is not selected
13 0b 1 = Ultra DMA mode 5 is selected
0 = Ultra DMA mode 5 is not selected
12 0b 1 = Ultra DMA mode 4 is selected
0 = Ultra DMA mode 4 is not selected
11 0b 1 = Ultra DMA mode 3 is selected
0 = Ultra DMA mode 3 is not selected
10 0b 1 = Ultra DMA mode 2 is selected
0 = Ultra DMA mode 2 is not selected
9 0b 1 = Ultra DMA mode 1 is selected
0 = Ultra DMA mode 1 is not selected
8 0b 1 = Ultra DMA mode 0 is selected
0 = Ultra DMA mode 0 is not selected
7 0b Reserved
6 1b 1 = Ultra DMA mode 6 and below are supported
5 1b 1 = Ultra DMA mode 5 and below are supported
4 1b 1 = Ultra DMA mode 4 and below are supported
3 1b 1 = Ultra DMA mode 3 and below are supported
2 1b 1 = Ultra DMA mode 2 and below are supported
1 1b 1 = Ultra DMA mode 1 and below are supported
0 1b 1 = Ultra DMA mode 0 IS supported
89 (O)F 0001h Time required for security erase unit completion
90 (O)F 0001h Time required for enhanced security erase completion
91 (O)V 00FEh Current advanced power management value
92 (O)V FFFEh Master Password Revision Code
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
93 Shall be 0000h for SATA devices
15 0b Shall be cleared to zero
14 0b Shall be set to one
13 0b 1 = Device detected CBLID-above VIH
0 = device detected CBLID-below VIL
Device 1 hardware reset result
Device 0 shall clear these bits to zero
Device 1 shall set these bits as follows:
12 0b Reserved
11 0b 0 = Device 1 did not assert PDIAG-
1 = Device 1 asserted PDIAG-
10–9 These bits indicate how Device 1 determined the device
number:
00 = Reserved
01 = a jumper was used
10 = the CSEL signal was used
11 = some other method was used or the method is un-
known
8 0b Shall be set to one
Device 0 hardware reset result. Device 1 shall clear these
bits to zero.
Device 0 shall set these bits as follows:
7 0b Reserved
6 0b 0 = Device 0 does not respond when Device 1 is selected.
1 = Device 0 responds when Device 1 is selected.
5 0b 0 = Device 0 did not detect the assertion of DASP-
1 = Device 0 detected the assertion of DASP-
4 0b 0 = Device 0 did not detect the assertion of PDIAG-
1 = Device 0 detected the assertion of PDIAG-
3 0b 0 = Device 0 failed diagnostics.
1 = Device 0 passed diagnostics.
2–1 00b These bits indicate how Device 0 determined the device
number:
00 = Reserved
01 = a jumper was used
10 = the CSEL signal was used
11 = some other method was used or the method is un-
known
0 0b Shall be set to one
94 15–8 F 00h Vendor's recommended acoustic management value
7–0 V 00h Current automatic acoustic management value
95 (O)V 0000h Stream Minimum Request Size
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
96 (O)V 0000h Streaming Transfer Time – DMA
97 (O)V 0000h Streaming Access Latency – DMA and PIO
98 (O)F 0000h 0000h Streaming Performance Granularity (98-99)
100 V Varies by capacity Maximum user LBA for 48-bit Address feature set
104 (O)V 0000h Streaming Transfer Time – PIO
105 ( )F 0008h Maximum number of 512-byte blocks of LBA Range Entries
per DATA SET MANAGEMENT command
106 Physical sector size/logical sector size
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13 F 1b 1 = Device has multiple logical sectors per physical sector
12 F 0b 1 = Device logical sector longer than 256 words
11–4 F 00000000b Reserved
3–0 F 0011b 2^x logical sectors per physical sector
107 (O)F 0000h Inter-seek delay for ISO-7779 acoustic testing in microsec-
onds
108 15–12 F 0101b NAA (3-0)
11–0 000000001010b IEEE OUI (23-12)
109 15–4 F 000001110101b IEEE OUI (11-0)
3–0 Varies Unique ID (35-32)
110 (M)F Varies 5-0 Unique ID (31-16)
111 (M)F Varies Unique ID (15-0)
112 (O)F 0000h 0000h
0000h 0000h
Reserved for 12- bit word-wide name extension to 128 bits
116 (O)V 0000h Reserved for INCITS TR-37-2004
117 (O)F 0000h 0000h Words per Logical Sector
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
119 Commands and feature sets supported (continued from
words 84–82)
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13–8 F 00000000b Reserved
7 F 0b 1 = Extended Power Conditions feature set is supported
6 F 0b 1 = Extended Status Reporting feature set is supported
5 F 0b 1 = Free-fall control feature set is supported
4 F 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3 F 1b 1 = READ LOG DMA EXT and WRITE LOG DMA EXT com-
mands are supported
2 F 1b 1 = The WRITE UNCORRECTABLE EXT command is supported
1 F 1b 1 = The Write-Read-Verify feature set is supported
0 F 0b Reserved for DDT
120 Commands and feature sets supported or enabled (contin-
ued from words 87–85)
15 0b Shall be cleared to zero
14 1b Shall be set to one
13–6 00000000b Reserved
5 0b 1 = Free-fall control feature set is enabled
4 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is
supported
3 1b 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT
commands are supported
2 1b 1 = The WRITE UNCORRECTABLE EXT command is supported
1 0b 1 = The Write-Read-Verify feature set is enabled
0 0b 1= Feature set "Disable Data Transfer After Error Detection"
is enabled
0 = Feature set "Disable Data Transfer After Error Detec-
tion" is disabled
121 F 0000h 0000h
0000h 0000h
0000h 0000h
Reserved for expanded supported and enabled settings
127 (O) 0000h Obsolete
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
128 Security status
15–9 F 0000000b Reserved
8 V 0b Security level 0 = High, 1 = Maximum
7–6 F 00b Reserved
5 F 1b 1 = Enhanced security erase supported
4 V 0b 1 = Security count expired
3 V 0b 1 = Security frozen
2 V 0b 1 = Security locked
1 V 0b 1 = Security enabled
0 F 1b 1 = Security supported
129–159 ( )X Vendor specific
data
Vendor specific
160 CFA power mode 1
15 F 0b Word 160 supported
14 F 0b Reserved
13 F 0b CFA power mode 1 is required for one or more commands
implemented by the device
12 V 0b CFA power mode 1 disabled
11–0 F 000000000000b Maximum current in ma
161 X 0000h 0000h
0000h 0000h
0000h 0000h
0000h
Reserved for assignment by the CompactFlash Association
168 15–4 F 000h Reserved
3-0 F 3h Device Nominal Form Factor
169 DATA SET MANAGEMENT command support
15–1 F 000000000000000
b
Reserved
0 F 1b 1 = The Trim bit in the DATA SET MANAGEMENT command
is supported
170 F 0000h 0000h
0000h 0000h
Additional product identifier
174 F 0000h 0000h Reserved
176 (O)V Varies Current media serial number (60 ASCII characters)
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
206 SCT Command Transport
15–12 X 0000b Vendor-specific
11–6 F 000000b Reserved
5 F 1b SCT Command Transport Data Tables supported
4 F 1b SCT Command Transport Features Control supported
3 F 0b SCT Command Transport Error Recovery Control supported
2 F 1b SCT Command Transport Write Same supported
1 F 0b Obsolete
0 F 1b SCT Command Transport supported
207 ( )F 0000h 0000h Reserved for CE-ATA
209 (O) Alignment of logical blocks within a larger physical block
15 F 0b Shall be cleared to zero
14 F 1b Shall be set to one
13–0 F 00000000000000b Logical sector offset within the first physical sector where
the first logical sector is placed
210 (O)V 0000h 0000h Write-Read-Verify Sector Count Mode 3 Only
212 (O)F 0000h 0001h Verify Sector Count Mode 2 Only
214 (O) NV Cache Capabilities
15–12 F 0000b NV Cache feature set version
11–8 F 0000b NV Cache Power Mode feature set version
7–5 F 000b Reserved
4 V 0b 1 = NV Cache feature set enabled
3–2 F 00b Reserved
1 V 0b 1 = NV Cache Power Mode feature set enabled
0 F 0b 1 = NV Cache Power Mode feature set supported
215 (O)V 0000h NV Cache Size in Logical Blocks (LSW)
216 (O)V 0000h NV Cache Size in Logical Blocks (MSW)
217 (M)F 0001h Nominal media rotation rate (ATA8-ACS 1699-D Revision 6)
218 (O)V 0000h Reserved
219 NV Cache Options
15–8 F 00h Reserved
7–0 F 00h Device Estimated Time to Spin Up in Seconds
220 15–8 F 00h Reserved
7–0 V 00h Write-Read-Verify feature set current mode
221 0000h Reserved
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 13: Identify Device (Continued)
See Note 1 for setting definitions
Word Bit(s) Setting Default Value Description
222 Transport Major revision number. 0000h or FFFFh = device
does not report version
15–12 0001b Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved
Parallel (Type = 0) Serial (Type = 1)
11–7 000000b Reserved Reserved
6 1b Supports SATA Rev 3.1
5 1b Supports SATA Rev 3.0
4 1b Supports SATA Rev 2.6
3 1b Supports SATA Rev 2.5
2 1b Supports SATA II: Extensions
1 1b Supports SATA 1.0a
0 1b Supports ATA8-APT ATA8-AST
223 (M)F 0000h Transport Minor revision number
224 ( )F 0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
Reserved for CE-ATA
234 (O)F 0001h Minimum number of 512 byte units per DOWNLOAD MI-
CROCODE command for mode 3
235 00FFh Maximum number of 512 byte units per DOWNLOAD MI-
CROCODE command for mode 3
236 0000h 0000h
0000h 0000h
0000h 0000h
0000h
Reserved
243 4000h Bit 14 = 1; Supports FDE security features
244 0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h 0000h
0000h
Reserved
255 (M)F Integrity word
15–8 varies Checksum
7–0 A5h Signature
Note: 1. F = The content of the word is fixed and does not change.
V = The content of the word is variable and may change depending on the state of the
device or the commands executed by the device.
X = The content of the word may be fixed or variable.
R = The content of the word is reserved and will be zero.
M600 M.2 Type 2260/2280 NAND Flash SSD
Device ID
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Commands
Table 14: Supported ATA Command Set
See ATA-8 standard for command details
Command Name Command Code (hex)
CHECK POWER MODE 98h or E5h
DEVICE CONFIGURATION RESTORE B1h/C1h
DEVICE CONFIGURATION FREEZE LOCK B1h/C3h
DEVICE CONFIGURATION IDENTIFY B1h/C1h
DEVICE CONFIGURATION SET B1h/C3h
DOWNLOAD MICROCODE 92h
EXECUTE DEVICE DIAGNOSTIC 90h
FLUSH CACHE E7h
FLUSH CACHE EXT EAh
IDENTIFY DEVICE ECh
IDLE E3h or 97h
IDLE IMMEDIATE E1h or 95h
INITIALIZE DEVICE PARAMETERS 91h
NOP 00h
READ BUFFER E4h
READ DMA (with retry) C8h
READ DMA (without retry) C9h
READ DMA EXT 25h
READ FPDMA QUEUED 60h
READ LOG EXT 2Fh
READ MULTIPLE C4h
READ MULTIPLE EXT 29h
READ NATIVE MAX ADDRESS F8h
READ NATIVE MAX ADDRESS EXT 27h
READ SECTOR(S) EXT 24h
READ SECTOR(S) (with retry) 20h
READ SECTOR(S) (without retry) 21h
READ VERIFY SECTOR EXT 42h
READ VERIFY SECTOR(S) (with retry) 40h
RECEIVE FPDMA QUEUED 65h
SANITIZE DEVICE B4h
SCT WRITE SAME 02h/0001h
02h/0002h
02h/0101h
02h/0102h
SCT RETURN ERROR RECOVERY CONTROL 030h/01h
SCT SET ERROR RECOVERY CONTROL 03h/01h
M600 M.2 Type 2260/2280 NAND Flash SSD
Commands
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 14: Supported ATA Command Set (Continued)
See ATA-8 standard for command details
Command Name Command Code (hex)
SCT SET FEATURE CONTROL 04h/01h
SCT RETURN FEATURE CONTROL 04h/02h
SCT RETURN FEATURE OPTION FLAG 04h/03h
SCT RETURN SCT DATA TABLE 05h/01h
SECURITY DISABLE PASSWORD F6h
SECURITY ERASE PREPARE F3h
SECURITY ERASE UNIT F4h
SECURITY FREEZE LOCK F5h
SECURITY SET PASSWORD F1h
SECURITY UNLOCK F2h
SEEK 7xh
SEND FPDMA QUEUED 64h
SET FEATURES EFh
SET MAX ADDRESS F9h
SET MAX – FREEZE LOCK F9h/04h
SET MAX – LOCK F9h/02h
SET MAX ADDRESS EXT 37h
SET MULTIPLE MODE C6h
SET MAX – SET PASSWORD F9h/01h
SET MAX – UNLOCK F9h/03h
SLEEP E6h or 99h
SMART DISABLE OPERATIONS B0h/D9h
SMART ENABLE OPERATIONS B0h/D8h
SMART ENABLE/DISABLE AUTOSAVE B0h/D2h
SMART EXECUTE OFF-LINE IMMEDIATE B0h/D4h
SMART READ DATA B0h/D0h
SMART READ LOG SECTOR B0h/D5h
SMART RETURN STATUS B0h/DAh
SMART WRITE LOG B0h/D6h
STANDBY E2h or 96h
STANDBY IMMEDIATE E0h or 94h
TRUSTED NON-DATA 5Bh
TRUSTED RECEIVE 5Ch
TRUSTED RECEIVE DMA 5Dh
TRUSTED SEND 5Eh
TRUSTED SEND DMA 5Fh
WRITE BUFFER E8h
M600 M.2 Type 2260/2280 NAND Flash SSD
Commands
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 32 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Table 14: Supported ATA Command Set (Continued)
See ATA-8 standard for command details
Command Name Command Code (hex)
WRITE DMA (with retry) CAh
WRITE DMA (without retry) CBh
WRITE DMA EXT 35h
WRITE DMA FUA EXT 3Dh
WRITE FPDMA QUEUED 61h
WRITE LOG EXT 3Fh
WRITE MULTIPLE C5h
WRITE MULTIPLE EXT 39h
WRITE MULTIPLE FUA EXT CEh
WRITE SECTOR(S) (with retry) 30h
WRITE SECTOR(S) EXT 34h
WRITE UNCORRECTABLE EXT 45h
M600 M.2 Type 2260/2280 NAND Flash SSD
Commands
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 33 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Compliance
Micron SSDs comply with the following:
RoHS “green”
CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003
FCC: CFR Title 47, Part 15, ICES-003, all Class B
UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Ed-
ition
BSMI (Taiwan): approval to CNS 13438
C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22
KCC RRL (Korea): approval to KCC MU2-C30025, KCC MU2-C30018 Class B
W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations
may apply to customers who place these products in the markets where WEEE is en-
forced.
TUV (Germany): approval to IEC60950/EN60950
VCCI
IC (Canada):
- This Class B digital apparatus complies with Canadian ICES-003.
- Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC Rules
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference in a residential installation. This equip-
ment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following meas-
ures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
M600 M.2 Type 2260/2280 NAND Flash SSD
Compliance
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 34 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Package Dimensions
Figure 5: M.2 Type 2260 Package
22.00mm ±0.15
0.866in ±0.006
60.00 ±0.15
2.362in ±0.006
4.00mm ±0.15
0.157in ±0.006
(2 PLCS)
5.20mm
0.205in MIN
3.50mm ±0.08
0.138in ±0.003 DIA thru
1.00mm
0.039in RAD thru
(2 PLCS)
19.85 ±0.15
0.781in
5.625mm ±0.150
0.221in ±0.0059
Pin 74
Pin 2
6.125mm ±0.150
0.2411in ±0.0059
3.50mm +0.10
-0.15
0.138in +0.004
-0.006
2.50mm ±0.15
0.098in ±0.006
(TYP)
2.00mm ±0.15
0.079in ±0.006
(TYP)
Pin 1
Pin 75
4.00mm
0.157in MIN
5.50mm ±0.10
0.217in ±0.004
(plated GND pad)
DIA
1.50mm
0.059in MAX
1.50mm
0.059in MAX
0.80mm ±0.08
0.031in ±0.003
1.20mm ±0.05
0.047in ±0.002
(2 PLCS)
DIA slot thru
1.00mm ±0.10
0.039in ±0.004 6.00mm ±0.10
0.236in ±0.004 DIA
(plated GND pad)
11.00mm
0.433in
for reference only
M600 M.2 Type 2260/2280 NAND Flash SSD
Package Dimensions
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 35 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Figure 6: M.2 Type 2280 Package
22.00mm ±0.15
0.866in ±0.006
80.00mm ±0.15
3.150in ±0.006
4.00mm ±0.15
0.157in ±0.006
(2 PLCS)
11.00mm
0.433in
3.50mm ±0.08
0.138in ±0.003 DIA THRU
1.00mm
1.50mm
0.059in
19.85mm ±0.15
0.781in ±0.006
5.625mm ±0.150
0.221in ±0.0059
1.20mm ±0.05
0.047in ±0.002
(2 PLCS)
0.80mm ±0.08
Pin 1
Pin 74
Pin 2
6.125mm ±0.150
0.2411in ±0.0059
3.50mm +0.10
-0.15
0.138in +0.004
-0.006
2.50mm ±0.15
0.098in ±0.006
(TYP)
4.00mm
0.157in
1.00mm ±0.10
0.039in ±0.004
6.00mm ±0.10
0.236in ±0.004 DIA
(plated GND pad)
2.00mm ±0.15
0.079in ±0.006
(TYP)
0.031in ±0.003
RAD thru
(2 PLCS)
0.039in
MAX
Pin 75
5.50mm ±0.10
0.217in ±0.004
(plated GND pad)
DIA
DIA slot thru
MIN
for reference only
M600 M.2 Type 2260/2280 NAND Flash SSD
Package Dimensions
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 36 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
References
Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available
at www.sata-io.org
SATA 3.2 GOLD
ATA-8 ACS3 (T13/2161-D, Revision 4k)
TCG Storage Security Subsystem Class Opal; Specification 2.00 Revision 1.00, Feb 24,
2012
TCG Core Specification; Specification 2.00 Revision 2.00, Nov 4, 2011
TCG Storage Interface Interactions: Specification Version 1.02 Revision 1.00 30 De-
cember, 2011
IEEE-1667: "Standard Protocol for Authentication in Host Attachments of Transient
Storage Devices"
M600 M.2 Type 2260/2280 NAND Flash SSD
References
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 37 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.
Revision History
Rev. C – 9/14
Updated Endurance: Total bytes written in Feature up to 144 to 300TB.
Updated Part Number Chart.
Updated table 7: Drive Lifetime and notes in Endurance.
Added Dynamic Write Acceleration.
Updated Adaptive Thermal Monitoring.
Rev. B – 7/14
Updated Operating temperature note on page 1.
Updated Part Number Chart.
Updated values and notes in the Drive Performance table.
Updated notes in the Drive Lifetime – Client Computing table.
Updated values and notes in the SATA Power Consumption table.
Updated notes in the Maximum Ratings table.
Rev. A – 03/14
Initial release.
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-4000
www.micron.com/products/support Sales inquiries: 800-932-4992
Micron and the Micron logo are trademarks of Micron Technology, Inc.
All other trademarks are the property of their respective owners.
This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.
Although considered final, these specifications are subject to change, as further product development and data characterization some-
times occur.
M600 M.2 Type 2260/2280 NAND Flash SSD
Revision History
PDF: 09005aef859ad464
m600_m2_2260_2280_ssd.pdf - Rev. C 9/14 EN 38 Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2014 Micron Technology, Inc. All rights reserved.