ALUMINUM ELECTROLYTIC CAPACITORS WT Chip Type, Wide Temperature Range series Chip type operating over wide temperature range of to - 55 ~ +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. WF Low impeadance UT Long Life WT Smaller ZT Specifications Item Performance Characteristics Category Temperature Range - 55 ~ +105C Rated Voltage Range 4 ~ 50V Rated Capacitance Range 0.1 ~ 1500F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (A) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20C tan Rated voltage (V) tan (MAX.) 4 0.40 6.3 0.30 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z- 25C / Z+20C Impedance ratio Z- 40C / Z+20C ZT / Z20 (MAX.) After 1000 hours' application of rated voltage at 105C, capacitors meet the characteristic requirements listed at right. Endurance Shelf Life Resistance to soldering heat 4 7 15 6.3 4 8 10 3 8 16 2 4 25 2 4 35 2 3 50 2 3 Within 25% of initial value for capacitors of 3mm unit, and 16V or less. Within 20% of initial value for capacitors of 25V or more. 200% or less of initial specified value Leakage current Initial specified value or less Capacitance change tan After leaving capacitors under no load at 105C for 1000 hours, they meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250C Capacitance change for 30 seconds. After removing from the hot plate and restored tan at room temperature, they meet the characteristic requirements Leakage current listed at right. Within 10% of initial value Initial specified value or less Initial specified value or less Black print on the case top. Marking Type numbering system (Example : 16V 10F) Chip Type (3 ~ 8 x 5.4L) Positive L 2 Lot No. 1 0.5 MAX. 2 3 4 5 6 7 8 Package code Size code Configuration A0.2 Capacitance tolerance (20%) Rated Capacitance (10F) +0.1 -0.2 (L0.3) Negative H 3 D code 3 ~ 8 (5.4L) GB 6.3 ~ 10 (L 5.8) GS 9 10 11 12 13 14 UWT 1 C 1 0 0 MC R 1 GB A0.2 C0.2 E A2P 10 16V 105C Marking Plastic platform 0.3 MAX. D0.5 1 Voltage B0.2 Capacitance D 3 ~ 8 (L 7.7) 8 ~ 10 (L = 10) code CR NR D 3 4 ~ 10 code 2 1 Rated voltage (16V) 3 Apply to 6.3 x 5.8, 6.3 x 7.7 Series name Type * The lead-free product is also available upon request. (8 x 10L, 10 x 10L) (mm) Pressure relief vent xL 3 x 5.4 4 x 5.4 A 1.5 1.8 2.1 2.4 2.4 2.4 5 x 5.4 6.3 x 5.4 6.3 x 5.8 6.3 x 7.7 8 x 5.4 8 x 10 10 x 10 3.3 2.9 3.2 A0.2 E L0.5 Lot No. In this case, L will be put at 11th digit of type numbering system. D A0.2 C0.2 B0.2 A2P 100 35V D0.5 1 Voltage 105C Marking Trade mark Plastic platform 0.3 MAX. 0.5 MAX. Positive Capacitance B 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 C 3.3 4.3 5.3 6.6 6.6 6.6 8.3 8.3 10.3 E 0.8 1.0 1.3 2.2 2.2 2.2 2.3 3.1 4.5 L 5.4 5.4 5.4 5.4 5.8 7.7 5.4 10 10 Negative H 1. Voltage mark for 6.3V is 6V . In case of marking for 3 units, "V" for rated voltage is omitted. 2. In case of marking for 3 units. Lot No is expressed by a digit (month code). H 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 Dimension table in next page. CAT.8100T ALUMINUM ELECTROLYTIC CAPACITORS WT series D x L (mm) Dimensions V Cap. (F) Code 4 0G 6.3 0J 10 1A 16 1C 25 1E 35 1V 50 1H 0.1 0R1 4 x 5.4 (3) 1.0 0.22 R22 4 x 5.4 (3) 2.6 0.33 R33 4 x 5.4 (3) 3.2 0.47 R47 4 x 5.4 (3) 3.8 1 010 4 x 5.4 (3) 6.3 (5.9) 2.2 2R2 3 x 5.4 7.5 4 x 5.4 (3) 11 (9) 3.3 3R3 3 x 5.4 9 4 x 5.4 14 4.7 4R7 4 x 5.4 (3) 13 (10) 4 x 5.4 15 5 x 5.4 19 5 x 5.4 23 5 x 5.4 25 6.3 x 5.4 30 42 8 x 5.4 4 x 5.4 (3) 18 (14) 10 100 22 220 4 x 5.4 22 4 x 5.4 22 5 x 5.4 27 5 x 5.4 30 6.3 x 5.4 38 6.3 x 5.4 33 330 5 x 5.4 30 5 x 5.4 30 5 x 5.4 35 6.3 x 5.4 40 6.3 x 5.4 48 8 x 5.4 47 470 5 x 5.4 36 5 x 5.4 36 6.3 x 5.4 46 6.3 x 5.4 50 8 x 5.4 100 101 6.3 x 5.4 60 6.3 x 5.4 60 6.3 x 5.4 60 6.3 x 5.4 60 6.3 x 7.7 150 151 6.3 x 5.8 86 6.3 x 5.8 86 220 221 330 331 6.3 x 7.7 105 6.3 x 7.7 105 470 471 8 x 10 210 8 x 10 680 681 8 x 10 210 8 x 10 1000 102 8 x 10 230 1500 152 10 x 10 310 8 x 5.4 102 (91) 59 (52) 6.3 x 7.7 51 (45) 60 66 (59) 6.3 x 5.8 63 6.3 x 7.7 63 91 6.3 x 7.7 84 8 x 10 140 6.3 x 5.8 86 6.3 x 7.7 95 8 x 10 140 8 x 10 155 10 x 10 180 102 (91) 6.3 x 7.7 105 6.3 x 7.7 105 8 x 10 155 8 x 10 190 10 x 10 220 8 x 10 195 8 x 10 195 8 x 10 190 10 x 10 300 210 8 x 10 210 8 x 10 230 10 x 10 300 210 10 x 10 310 10 x 10 310 8 x 10 230 10 x 10 310 10 x 10 310 8 x 5.4 ( ) is also available with 3mm upon request. In such a case, 2 will be put at 12th digit of type numbering system. Size 6.3 x 5.8 is available for capacitors marked. " " In such a case, 6 will be put at 12th digit of type numbering system. Rated Case size ripple Rated Ripple (mA rms) at 105C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz~ 1.50 Taping specifications are given in page 22. Recommended land size are given in page 23 Please refer to page 3 for the minimum order quantity. CAT.8100T