MC9S12XDP512 Data Sheet Covers S12XD, S12XB & S12XA Families HCS12X Microcontrollers MC9S12XDP512RMV2 Rev. 2.21 October 2009 freescale.com MC9S12XDP512RMV2 Data Sheet MC9S12XDP512RMV2 Rev. 2.21 October 2009 To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to: http://freescale.com/ A full list of family members and options is included in the appendices. Read page 29 first to understand the maskset specific chapters of this document This document contains information for all constituent modules, with the exception of the S12X CPU. For S12X CPU information please refer to the CPU S12X Reference Manual. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. This product incorporates SuperFlash(R) technology licensed from SST. (c) Freescale Semiconductor, Inc., 2008. All rights reserved. MC9S12XDP512 Data Sheet, Rev. 2.21 4 Freescale Semiconductor Revision History Date Revision Level April, 2005 02.07 New Book May, 2005 02.08 Minor corrections May, 2005 02.09 removed ESD Machine Model from electrical characteristics added thermal characteristics added more details to run current measurement configurations VDDA supply voltage range 3.15V - 3.6V fot ATD Operating Characteristics I/O Chararcteristics for alll pins except EXTAL, XTAL .... corrected VREG electrical spec IDD wait max 95mA May 2005 02.10 Improvements to NVM reliabity spec, added part numbers July 2005 02.11 Added ROM parts to App. October 2005 02.12 Single Souce S12XD Fam. Document, New Memory Map Figures, May 2006 2.13 SPI electricals updated Voltage Regulator electricals updated Added Partnumbers and 1L15Y maskset Updated App. E 6SCI's on 112 pin DT/P512 and 3 SPI's on all D256 parts June 2006 2.14 Data Sheet covers S12XD/B & A Family Included differnt pull device specification for differnt masksets July 2006 2.15 Minor Corrections and Improvments June 2007 2.16 Added 2M42E and 1M84E masksets July 2007 2.17 Modified Appendix April 2008 2.18 Better explanation of ATD0/1 for S12XD-Family see page 1305 S12XB256 ATD specification changed see Appendix E.6 added M23S maskset August 2008 2.19 Corrected XGRAMSIZE of S12XD256 on page 44 Corrected 17.4.2.4 XGATE Memory Map Scheme Corrected 18.4.2.4 XGATE Memory Map Scheme September 2009 2.20 Corrected Table E-6 , 30K flash memory available for XGATE on B256 October 2009 2.21 Corrected Footnote in Appendix E3 regarding Shared XGATE/CPU area Description MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 5 MC9S12XDP512 Data Sheet, Rev. 2.21 6 Freescale Semiconductor Section Number Title Page Chapter 1 Device Overview MC9S12XD-Family . . . . . . . . . . . . . . . . . . . . 31 Chapter 2 Clocks and Reset Generator (S12CRGV6) . . . . . . . . . . . . . . . . 79 Chapter 3 Pierce Oscillator (S12XOSCLCPV1) . . . . . . . . . . . . . . . . . . . . 119 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description125 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV3) . . . . . . . . . . 159 Chapter 6 XGATE (S12XGATEV2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) . . . . . . . . . . . . 309 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) . . . . . . . . . . . . . . 363 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description. . . . . . . . . 395 Chapter 10 419 Freescale's Scalable Controller Area Network (S12MSCANV3). Chapter 11 Serial Communication Interface (S12SCIV5) . . . . . . . . . . . . . 477 Chapter 12 Serial Peripheral Interface (S12SPIV4) . . . . . . . . . . . . . . . . . . 515 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) . . . . . . . . . . . . . . 541 Chapter 14 Voltage Regulator (S12VREG3V3V5) . . . . . . . . . . . . . . . . . . . 555 Chapter 15 Background Debug Module (S12XBDMV2) . . . . . . . . . . . . . . 569 Chapter 16 Interrupt (S12XINTV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595 Chapter 17 Memory Mapping Control (S12XMMCV2) . . . . . . . . . . . . . . . . 613 Chapter 18 Memory Mapping Control (S12XMMCV3) . . . . . . . . . . . . . . . 651 Chapter 19 S12X Debug (S12XDBGV2) Module . . . . . . . . . . . . . . . . . . . . 693 Chapter 20 S12X Debug (S12XDBGV3) Module . . . . . . . . . . . . . . . . . . . . 745 Chapter 21 External Bus Interface (S12XEBIV2) . . . . . . . . . . . . . . . . . . . 787 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) . . . . . . . 807 Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) . . . . . . 901 Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) . . . . . . 975 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 5 Section Number Title Page Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) . . . . . . . . . . . . 1039 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) . . . . . . . . . . . . 1073 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2). . . . . . . . . . . . 1107 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1). . . . . . . . . . . . 1149 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1). . . . . . . . . . . . 1191 Chapter 30 Security (S12X9SECV2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1231 Appendix A Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239 Appendix B Package Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1290 Appendix C Recommended PCB Layout . . . . . . . . . . . . . . . . . . . . . . . . . 1294 Appendix D Using L15Y Silicon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1299 Appendix E Derivative Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1300 Appendix F Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1308 Appendix G Detailed Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1309 MC9S12XDP512 Data Sheet, Rev. 2.21 6 Freescale Semiconductor Section Number Title Page Chapter 1Device Overview MC9S12XD-Family 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 1.1.1 MC9S12XD/B/A Family Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 1.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 1.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 1.1.4 Device Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 1.1.5 Part ID Assignments & Maskset Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 1.2.1 Device Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 1.2.2 Signal Properties Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 1.2.3 Detailed Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 1.2.4 Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 System Clock Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Chip Configuration Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 1.5.1 User Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 1.5.2 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 1.5.3 Freeze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 Resets and Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 1.6.1 Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 1.6.2 Effects of Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 COP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 ATD0 External Trigger Input Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 ATD1 External Trigger Input Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.1 2.2 2.3 2.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 2.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 2.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 2.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 2.2.1 VDDPLL and VSSPLL -- Operating and Ground Voltage Pins . . . . . . . . . . . . . . . . . . . . . 82 2.2.2 XFC -- External Loop Filter Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 2.2.3 RESET -- Reset Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 2.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 2.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 2.4.1 Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 2.4.2 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 2.4.3 Low Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 9 Section Number 2.5 2.6 Title Page Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 2.5.1 Description of Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 2.5.2 Clock Monitor Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 2.5.3 Computer Operating Properly Watchdog (COP) Reset . . . . . . . . . . . . . . . . . . . . . . . . . 115 2.5.4 Power On Reset, Low Voltage Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 2.6.1 Real Time Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 2.6.2 PLL Lock Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 2.6.3 Self Clock Mode Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Chapter 3 Pierce Oscillator (S12XOSCLCPV1) 3.1 3.2 3.3 3.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 3.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 3.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 3.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 3.2.1 VDDPLL and VSSPLL -- Operating and Ground Voltage Pins . . . . . . . . . . . . . . . . . . . . 120 3.2.2 EXTAL and XTAL -- Input and Output Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 3.2.3 XCLKS -- Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 3.4.1 Gain Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 3.4.2 Clock Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 3.4.3 Wait Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 3.4.4 Stop Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.1 4.2 4.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 4.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 4.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 4.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 4.2.1 ANx (x = 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) -- Analog Input Channel x Pins 127 4.2.2 ETRIG3, ETRIG2, ETRIG1, ETRIG0 -- External Trigger Pins . . . . . . . . . . . . . . . . . 127 4.2.3 VRH, VRL -- High Reference Voltage Pin, Low Reference Voltage Pin . . . . . . . . . . . . 127 4.2.4 VDDA, VSSA -- Analog Circuitry Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . 127 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 MC9S12XDP512 Data Sheet, Rev. 2.21 10 Freescale Semiconductor Section Number 4.4 4.5 4.6 Title Page 4.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127 4.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 4.4.1 Analog Sub-block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 4.4.2 Digital Sub-Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153 4.4.3 Operation in Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155 Chapter 5Analog-to-Digital Converter (S12ATD10B8CV3) 5.1 5.2 5.3 5.4 5.5 5.6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 5.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 5.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 5.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 5.2.1 ANx (x = 7, 6, 5, 4, 3, 2, 1, 0) -- Analog Input Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 5.2.2 ETRIG3, ETRIG2, ETRIG1, and ETRIG0 -- External Trigger Pins . . . . . . . . . . . . . . 160 5.2.3 VRH and VRL -- High and Low Reference Voltage Pins . . . . . . . . . . . . . . . . . . . . . . . . 160 5.2.4 VDDA and VSSA -- Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 5.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 5.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 5.4.1 Analog Sub-Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 5.4.2 Digital Sub-Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Chapter 6 XGATE (S12XGATEV2) 6.1 6.2 6.3 6.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 6.1.1 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 6.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 6.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 6.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 6.3.1 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 6.4.1 XGATE RISC Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 6.4.2 Programmer's Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202 6.4.3 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 11 Section Number 6.5 6.6 6.7 6.8 6.9 Title Page 6.4.4 Semaphores . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 6.4.5 Software Error Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 6.5.1 Incoming Interrupt Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 6.5.2 Outgoing Interrupt Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 6.6.1 Debug Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 6.6.2 Entering Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 6.6.3 Leaving Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 6.8.1 Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208 6.8.2 Instruction Summary and Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212 6.8.3 Cycle Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 6.8.4 Thread Execution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 6.8.5 Instruction Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 6.8.6 Instruction Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 Initialization and Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 6.9.1 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 6.9.2 Code Example (Transmit "Hello World!" on SCI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.1 7.2 7.3 7.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 7.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 7.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 7.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.1 IOC7 -- Input Capture and Output Compare Channel 7 . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.2 IOC6 -- Input Capture and Output Compare Channel 6 . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.3 IOC5 -- Input Capture and Output Compare Channel 5 . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.4 IOC4 -- Input Capture and Output Compare Channel 4 . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.5 IOC3 -- Input Capture and Output Compare Channel 3 . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.6 IOC2 -- Input Capture and Output Compare Channel 2 . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.7 IOC1 -- Input Capture and Output Compare Channel 1 . . . . . . . . . . . . . . . . . . . . . . . . 311 7.2.8 IOC0 -- Input Capture and Output Compare Channel 0 . . . . . . . . . . . . . . . . . . . . . . . . 311 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 7.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312 7.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350 7.4.1 Enhanced Capture Timer Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357 7.4.2 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360 MC9S12XDP512 Data Sheet, Rev. 2.21 12 Freescale Semiconductor Section Number Title Page 7.4.3 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 361 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.1 8.2 8.3 8.4 8.5 8.6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 8.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 8.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 363 8.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 8.2.1 PWM7 -- PWM Channel 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 8.2.2 PWM6 -- PWM Channel 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 364 8.2.3 PWM5 -- PWM Channel 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8.2.4 PWM4 -- PWM Channel 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8.2.5 PWM3 -- PWM Channel 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8.2.6 PWM3 -- PWM Channel 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8.2.7 PWM3 -- PWM Channel 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8.2.8 PWM3 -- PWM Channel 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365 8.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 8.4.1 PWM Clock Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380 8.4.2 PWM Channel Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.1 9.2 9.3 9.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395 9.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395 9.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 9.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 9.2.1 IIC_SCL -- Serial Clock Line Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 9.2.2 IIC_SDA -- Serial Data Line Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 9.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 9.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 9.4.1 I-Bus Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 409 9.4.2 Operation in Run Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 9.4.3 Operation in Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 13 Section Number 9.5 9.6 9.7 Title Page 9.4.4 Operation in Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413 9.7.1 IIC Programming Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 10.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 10.1.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 10.1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 10.1.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421 10.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421 10.2.1 RXCAN -- CAN Receiver Input Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421 10.2.2 TXCAN -- CAN Transmitter Output Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421 10.2.3 CAN System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 421 10.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422 10.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 422 10.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 424 10.3.3 Programmer's Model of Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445 10.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456 10.4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 456 10.4.2 Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 10.4.3 Identifier Acceptance Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 460 10.4.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466 10.4.5 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467 10.4.6 Reset Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472 10.4.7 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472 10.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474 10.5.1 MSCAN initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474 10.5.2 Bus-Off Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474 Chapter 11 Serial Communication Interface (S12SCIV5) 11.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477 11.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477 11.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 477 11.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478 11.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 478 11.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 11.2.1 TXD -- Transmit Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 MC9S12XDP512 Data Sheet, Rev. 2.21 14 Freescale Semiconductor Section Number Title Page 11.2.2 RXD -- Receive Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 11.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 11.3.1 Module Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 480 11.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 481 11.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 493 11.4.1 Infrared Interface Submodule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494 11.4.2 LIN Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 494 11.4.3 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495 11.4.4 Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 496 11.4.5 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 497 11.4.6 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 502 11.4.7 Single-Wire Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 510 11.4.8 Loop Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 11.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 11.5.1 Reset Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 11.5.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 11.5.3 Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 512 11.5.4 Recovery from Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514 11.5.5 Recovery from Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 514 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515 12.1.1 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515 12.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515 12.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 515 12.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 516 12.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517 12.2.1 MOSI -- Master Out/Slave In Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517 12.2.2 MISO -- Master In/Slave Out Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 517 12.2.3 SS -- Slave Select Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518 12.2.4 SCK -- Serial Clock Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518 12.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518 12.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 518 12.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 519 12.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 528 12.4.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 529 12.4.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530 12.4.3 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 12.4.4 SPI Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535 12.4.5 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 535 12.4.6 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 15 Section Number Title Page 12.4.7 Low Power Mode Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 537 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 13.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 13.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 13.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 13.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542 13.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 542 13.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 543 13.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551 13.4.1 Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 551 13.4.2 Interrupt Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 552 13.4.3 Hardware Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 13.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 13.5.1 Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 13.5.2 Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 13.5.3 Flag Clearing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 553 Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555 14.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555 14.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 555 14.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 556 14.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557 14.2.1 VDDR -- Regulator Power Input Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 557 14.2.2 VDDA, VSSA -- Regulator Reference Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . 557 14.2.3 VDD, VSS -- Regulator Output1 (Core Logic) Pins . . . . . . . . . . . . . . . . . . . . . . . . . . 557 14.2.4 VDDPLL, VSSPLL -- Regulator Output2 (PLL) Pins . . . . . . . . . . . . . . . . . . . . . . . . . 558 14.2.5 VREGEN -- Optional Regulator Enable Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558 14.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558 14.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 558 14.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 559 14.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564 14.4.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564 14.4.2 Regulator Core (REG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 564 14.4.3 Low-Voltage Detect (LVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565 14.4.4 Power-On Reset (POR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565 14.4.5 Low-Voltage Reset (LVR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565 14.4.6 Regulator Control (CTRL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565 MC9S12XDP512 Data Sheet, Rev. 2.21 16 Freescale Semiconductor Section Number Title Page 14.4.7 Autonomous Periodical Interrupt (API) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565 14.4.8 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566 14.4.9 Description of Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566 14.4.10Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 566 Chapter 15 Background Debug Module (S12XBDMV2) 15.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569 15.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569 15.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 570 15.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571 15.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572 15.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572 15.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572 15.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 573 15.3.3 Family ID Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 577 15.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 15.4.1 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 15.4.2 Enabling and Activating BDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 578 15.4.3 BDM Hardware Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 579 15.4.4 Standard BDM Firmware Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580 15.4.5 BDM Command Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 582 15.4.6 BDM Serial Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584 15.4.7 Serial Interface Hardware Handshake Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586 15.4.8 Hardware Handshake Abort Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588 15.4.9 SYNC -- Request Timed Reference Pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 591 15.4.10Instruction Tracing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 592 15.4.11Serial Communication Time Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 593 Chapter 16 Interrupt (S12XINTV1) 16.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 595 16.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596 16.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596 16.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 596 16.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 598 16.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 599 16.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 599 16.3.1 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600 16.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607 16.4.1 S12X Exception Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607 16.4.2 Interrupt Prioritization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 17 Section Number Title Page 16.4.3 XGATE Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608 16.4.4 Priority Decoders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 608 16.4.5 Reset Exception Requests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 16.4.6 Exception Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 609 16.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610 16.5.1 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610 16.5.2 Interrupt Nesting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610 16.5.3 Wake Up from Stop or Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 611 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 613 17.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 613 17.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 613 17.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614 17.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 614 17.3 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616 17.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 616 17.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 617 17.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630 17.4.1 MCU Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 630 17.4.2 Memory Map Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 631 17.4.3 Chip Access Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640 17.4.4 Chip Bus Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 642 17.4.5 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643 17.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643 17.5.1 CALL and RTC Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 643 17.5.2 Port Replacement Registers (PRRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 644 17.5.3 On-Chip ROM Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 646 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 651 18.1.1 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652 18.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652 18.1.3 S12X Memory Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653 18.1.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 653 18.1.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654 18.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 654 18.3 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656 18.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656 18.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 657 MC9S12XDP512 Data Sheet, Rev. 2.21 18 Freescale Semiconductor Section Number Title Page 18.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671 18.4.1 MCU Operating Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 671 18.4.2 Memory Map Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 672 18.4.3 Chip Access Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 681 18.4.4 Chip Bus Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683 18.4.5 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684 18.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684 18.5.1 CALL and RTC Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 684 18.5.2 Port Replacement Registers (PRRs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 685 18.5.3 On-Chip ROM Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 687 Chapter 19 S12X Debug (S12XDBGV2) Module 19.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693 19.1.1 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 693 19.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694 19.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 694 19.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695 19.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 695 19.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697 19.3.1 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 697 19.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 714 19.4.1 DBG Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 714 19.4.2 Comparator Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 715 19.4.3 Trigger Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 718 19.4.4 State Sequence Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 720 19.4.5 Trace Buffer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 721 19.4.6 Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 728 19.4.7 Breakpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 729 Chapter 20 S12X Debug (S12XDBGV3) Module 20.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745 20.1.1 Glossary Of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745 20.1.2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745 20.1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 746 20.1.4 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 746 20.1.5 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 747 20.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 747 20.3 Memory Map and Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748 20.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 748 20.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 749 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 19 Section Number Title Page 20.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 768 20.4.1 S12XDBG Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 768 20.4.2 Comparator Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 769 20.4.3 Trigger Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 772 20.4.4 State Sequence Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 774 20.4.5 Trace Buffer Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 775 20.4.6 Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 782 20.4.7 Breakpoints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 783 Chapter 21 External Bus Interface (S12XEBIV2) 21.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787 21.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787 21.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 787 21.1.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 788 21.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 788 21.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 790 21.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 790 21.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 790 21.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794 21.4.1 Operating Modes and External Bus Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 794 21.4.2 Internal Visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 795 21.4.3 Accesses to Port Replacement Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 798 21.4.4 Stretched External Bus Accesses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 798 21.4.5 Data Select and Data Direction Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 799 21.4.6 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 801 21.5 Initialization/Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 801 21.5.1 Normal Expanded Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 802 21.5.2 Emulation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 803 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 807 22.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 808 22.1.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 808 22.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 810 22.2.1 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 810 22.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 817 22.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 817 22.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 820 22.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881 22.4.1 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 881 MC9S12XDP512 Data Sheet, Rev. 2.21 20 Freescale Semiconductor Section Number Title Page 22.4.2 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 883 22.4.3 Pin Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 887 22.4.4 Expanded Bus Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 888 22.4.5 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 889 22.5 Initialization and Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 889 Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Chapter 23Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 901 23.0.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 901 23.0.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 902 Figure 23-1.External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 904 23.0.3 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 904 Table 23-1.Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910 23.0.4 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 910 23.0.5 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 913 Table 23-66.Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 962 23.0.6 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 963 23.0.7 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 965 23.0.8 Pin Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 968 23.0.9 Expanded Bus Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 969 23.0.10Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971 23.0.10.3Initialization and Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 971 Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Chapter 24Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 975 24.0.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 975 24.0.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 976 Figure 24-1.External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 978 24.0.3 Signal Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 978 Table 24-1.Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983 24.0.4 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 983 24.0.5 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 985 Table 24-59.Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1028 24.0.6 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1029 24.0.7 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1031 24.0.8 Pin Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1033 24.0.9 Low-Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1034 24.0.9.3Initialization and Application Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1035 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 21 Section Number Title Page Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039 25.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039 25.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039 25.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1039 25.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040 25.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040 25.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040 25.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1040 25.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1043 25.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1051 25.4.1 EEPROM Command Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1051 25.4.2 EEPROM Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1054 25.4.3 Illegal EEPROM Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1068 25.5 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069 25.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069 25.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069 25.5.3 Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069 25.6 EEPROM Module Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1069 25.6.1 Unsecuring the MCU in Special Single Chip Mode using BDM . . . . . . . . . . . . . . . . 1070 25.7 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1070 25.7.1 EEPROM Reset Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1070 25.7.2 Reset While EEPROM Command Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1070 25.8 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1070 25.8.1 Description of EEPROM Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1071 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073 26.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073 26.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073 26.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1073 26.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074 26.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074 26.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074 26.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1074 26.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1078 26.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1086 26.4.1 EEPROM Command Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1086 26.4.2 EEPROM Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1089 26.4.3 Illegal EEPROM Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1103 MC9S12XDP512 Data Sheet, Rev. 2.21 22 Freescale Semiconductor Section Number Title Page 26.5 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104 26.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104 26.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104 26.5.3 Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104 26.6 EEPROM Module Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1104 26.6.1 Unsecuring the MCU in Special Single Chip Mode using BDM . . . . . . . . . . . . . . . . 1105 26.7 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105 26.7.1 EEPROM Reset Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105 26.7.2 Reset While EEPROM Command Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105 26.8 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1105 26.8.1 Description of EEPROM Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1106 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1107 27.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1107 27.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1107 27.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108 27.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1108 27.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1109 27.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1110 27.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1110 27.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1113 27.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126 27.4.1 Flash Command Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1126 27.4.2 Flash Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1129 27.4.3 Illegal Flash Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1144 27.5 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145 27.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145 27.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145 27.5.3 Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145 27.6 Flash Module Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1145 27.6.1 Unsecuring the MCU using Backdoor Key Access . . . . . . . . . . . . . . . . . . . . . . . . . . . 1146 27.6.2 Unsecuring the MCU in Special Single Chip Mode using BDM . . . . . . . . . . . . . . . . 1147 27.7 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147 27.7.1 Flash Reset Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147 27.7.2 Reset While Flash Command Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147 27.8 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1147 27.8.1 Description of Flash Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1148 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 23 Section Number Title Page Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149 28.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149 28.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1149 28.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150 28.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150 28.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150 28.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1151 28.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1151 28.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1153 28.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166 28.4.1 Flash Command Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1166 28.4.2 Flash Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1169 28.4.3 Illegal Flash Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1185 28.5 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1186 28.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1186 28.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1186 28.5.3 Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1186 28.6 Flash Module Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1186 28.6.1 Unsecuring the MCU using Backdoor Key Access . . . . . . . . . . . . . . . . . . . . . . . . . . . 1187 28.6.2 Unsecuring the MCU in Special Single Chip Mode using BDM . . . . . . . . . . . . . . . . 1188 28.7 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188 28.7.1 Flash Reset Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188 28.7.2 Reset While Flash Command Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188 28.8 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1188 28.8.1 Description of Flash Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1189 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191 29.1.1 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191 29.1.2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1191 29.1.3 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1192 29.1.4 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1192 29.2 External Signal Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1192 29.3 Memory Map and Register Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1193 29.3.1 Module Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1193 29.3.2 Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1195 29.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1208 29.4.1 Flash Command Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1208 29.4.2 Flash Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1211 MC9S12XDP512 Data Sheet, Rev. 2.21 24 Freescale Semiconductor Section Number 29.5 29.6 29.7 29.8 Title Page 29.4.3 Illegal Flash Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1226 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227 29.5.1 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227 29.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227 29.5.3 Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227 Flash Module Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227 29.6.1 Unsecuring the MCU using Backdoor Key Access . . . . . . . . . . . . . . . . . . . . . . . . . . . 1227 29.6.2 Unsecuring the MCU in Special Single Chip Mode using BDM . . . . . . . . . . . . . . . . 1229 Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229 29.7.1 Flash Reset Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229 29.7.2 Reset While Flash Command Active . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1229 29.8.1 Description of Flash Interrupt Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1230 Chapter 30 Security (S12X9SECV2) 30.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1231 30.1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1231 30.1.2 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1232 30.1.3 Securing the Microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1232 30.1.4 Operation of the Secured Microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1233 30.1.5 Unsecuring the Microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1235 30.1.6 Reprogramming the Security Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1236 30.1.7 Complete Memory Erase (Special Modes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1236 Appendix A Electrical Characteristics A.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239 A.1.1 Parameter Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239 A.1.2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1239 A.1.3 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1240 A.1.4 Current Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1240 A.1.5 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1241 A.1.6 ESD Protection and Latch-up Immunity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1241 A.1.7 Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1243 A.1.8 Power Dissipation and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1244 A.1.9 I/O Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1246 A.1.10 Supply Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1249 A.2 ATD Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1253 A.2.1 ATD Operating Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1253 A.2.2 Factors Influencing Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1254 A.2.3 ATD Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1256 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 25 Section Number Title Page A.3 NVM, Flash, and EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259 A.3.1 NVM Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1259 A.3.2 NVM Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1262 A.4 Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1264 A.4.1 Chip Power-up and Voltage Drops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265 A.4.2 Output Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1265 A.5 Reset, Oscillator, and PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1267 A.5.1 Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1267 A.5.2 Oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1268 A.5.3 Phase Locked Loop. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1270 A.6 MSCAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1273 A.7 SPI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1274 A.7.1 Master Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1274 A.7.2 Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1276 A.8 External Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1279 A.8.1 Normal Expanded Mode (External Wait Feature Disabled). . . . . . . . . . . . . . . . . . . . . 1279 A.8.2 Normal Expanded Mode (External Wait Feature Enabled) . . . . . . . . . . . . . . . . . . . . . 1281 A.8.3 Emulation Single-Chip Mode (Without Wait States) . . . . . . . . . . . . . . . . . . . . . . . . . . 1284 A.8.4 Emulation Expanded Mode (With Optional Access Stretching) . . . . . . . . . . . . . . . . . 1286 A.8.5 External Tag Trigger Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1289 Appendix B Package Information B.1 144-Pin LQFP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1291 B.2 112-Pin LQFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1292 B.3 80-Pin QFP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1293 Appendix C Recommended PCB Layout Appendix D Using L15Y Silicon Appendix E Derivative Differences E.1 E.2 E.3 E.4 E.5 E.6 Memory Sizes and Package Options S12XD - Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1300 Memory Sizes and Package Options S12XA & S12XB Family. . . . . . . . . . . . . . . . . . . . . . . . . 1302 MC9S12XD-Family Flash Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1303 MC9S12XD/A/B -Family SRAM & EEPROM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . 1304 Peripheral Sets S12XD - Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1305 Peripheral Sets S12XA & S12XB - Family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1306 MC9S12XDP512 Data Sheet, Rev. 2.21 26 Freescale Semiconductor Section Number E.7 Title Page Pinout explanations: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1307 Appendix F Ordering Information Appendix G Detailed Register Map MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 27 Section Number Title Page MC9S12XDP512 Data Sheet, Rev. 2.21 28 Freescale Semiconductor NOTE This documentation covers all devices in the S12XD, S12XB and S12XA families. A full list of these devices and their features can be found in the following chapters: * E.1 Memory Sizes and Package Options S12XD - Family * E.2 Memory Sizes and Package Options S12XA & S12XB Family * E.5 Peripheral Sets S12XD - Family * E.6 Peripheral Sets S12XA & S12XB - Family * Table 1-6 Partnames, Masksets and assigned PartID's This document includes different sections for S12XDPIM, S1XMMC, S12XDBG, S12XEETX and S12XFTX because the different masksets of the S12XD, S12XB and S12XA families include differnt configurations or versions of the modules or have different memory sizes. Table 0-1 shows the maskset specific chapters in this documentation. Table 0-1. Maskset Specific Documentation Chapters in this Documentation L15Y (512k Flash) M84E (256K Flash) Chapter 21 External Bus Interface (S12XEBIV2) 787 Chapter 17 Memory Mapping Control (S12XMMCV2) 613 Chapter 18 Memory Mapping Control (S12XMMCV3) 649 Chapter 19 Debug (S12XDBGV2) 691 Chapter 20 S12X Debug (S12XDBGV3) Module 743 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 805 M42E (128K Flash) Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 899 Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 973 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 1037 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 1071 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 1105 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 1147 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 1189 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV3) 157 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 29 Chapter 1 Device Overview MC9S12XD-Family describes pinouts, detailed pin description , interrupts and register map of the cover part MC9S12XDP512 (maskset L15Y). For availability of the modules on other members of the S12XA, S12XB and S12XD families please refer to Appendix E Derivative Differences. For pinout explanations of the different parts refer to E.7 Pinout explanations:. For a list of available partnames /masksets refer to Table 1-6. MC9S12XDP512 Data Sheet, Rev. 2.21 30 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family Chapter 1 Device Overview MC9S12XD-Family 1.1 Introduction The MC9S12XD family will retain the low cost, power consumption, EMC and code-size efficiency advantages currently enjoyed by users of Freescale's existing 16-Bit MC9S12 MCU Family. Based around an enhanced S12 core, the MC9S12XD family will deliver 2 to 5 times the performance of a 25-MHz S12 whilst retaining a high degree of pin and code compatibility with the S12. The MC9S12XD family introduces the performance boosting XGATE module. Using enhanced DMA functionality, this parallel processing module offloads the CPU by providing high-speed data processing and transfer between peripheral modules, RAM, Flash EEPROM and I/O ports. Providing up to 80 MIPS of performance additional to the CPU, the XGATE can access all peripherals, Flash EEPROM and the RAM block. The MC9S12XD family is composed of standard on-chip peripherals including up to 512 Kbytes of Flash EEPROM, 32 Kbytes of RAM, 4 Kbytes of EEPROM, six asynchronous serial communications interfaces (SCI), three serial peripheral interfaces (SPI), an 8-channel IC/OC enhanced capture timer, an 8-channel, 10-bit analog-to-digital converter, a 16-channel, 10-bit analog-to-digital converter, an 8-channel pulse-width modulator (PWM), five CAN 2.0 A, B software compatible modules (MSCAN12), two inter-IC bus blocks, and a periodic interrupt timer. The MC9S12XD family has full 16-bit data paths throughout. The non-multiplexed expanded bus interface available on the 144-pin versions allows an easy interface to external memories The inclusion of a PLL circuit allows power consumption and performance to be adjusted to suit operational requirements. System power consumption can be further improved with the new "fast exit from stop mode" feature. In addition to the I/O ports available in each module, up to 25 further I/O ports are available with interrupt capability allowing wake-up from stop or wait mode. Family members in 144-pin LQFP will be available with external bus interface and parts in 112-pin LQFP or 80-pin QFP package without external bus interface. See Appendix E Derivative Differences for package options. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 31 Chapter 1 Device Overview MC9S12XD-Family 1.1.1 MC9S12XD/B/A Family Features This section lists the features which are available on MC9S12XDP512RMV2. See Appendix E Derivative Differences for availability of features and memory sizes on other family members. * * * * * * * HCS12X Core -- 16-bit HCS12X CPU - Upward compatible with MC9S12 instruction set - Interrupt stacking and programmer's model identical to MC9S12 - Instruction queue - Enhanced indexed addressing - Enhanced instruction set -- EBI (external bus interface) -- MMC (module mapping control) -- INT (interrupt controller) -- DBG (debug module to monitor HCS12X CPU and XGATE bus activity) -- BDM (background debug mode) XGATE (peripheral coprocessor) -- Parallel processing module off loads the CPU by providing high-speed data processing and transfer -- Data transfer between Flash EEPROM, RAM, peripheral modules, and I/O ports PIT (periodic interrupt timer) -- Four timers with independent time-out periods -- Time-out periods selectable between 1 and 224 bus clock cycles CRG (clock and reset generator) -- Low noise/low power Pierce oscillator -- PLL -- COP watchdog -- Real time interrupt -- Clock monitor -- Fast wake-up from stop mode Port H & Port J with interrupt functionality -- Digital filtering -- Programmable rising or falling edge trigger Memory -- 512, 256 and 128-Kbyte Flash EEPROM -- 4 and 2-Kbyte EEPROM -- 32, 16 and 12-Kbyte RAM One 16-channel and one 8-channel ADC (analog-to-digital converter) MC9S12XDP512 Data Sheet, Rev. 2.21 32 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family * * * * * * -- 10-bit resolution -- External and internal conversion trigger capabilityFiveFourTwo 1M bit per second, CAN 2.0 A, B software compatible modules -- Five receive and three transmit buffers -- Flexible identifier filter programmable as 2 x 32 bit, 4 x 16 bit, or 8 x 8 bit -- Four separate interrupt channels for Rx, Tx, error, and wake-up -- Low-pass filter wake-up function -- Loop-back for self-test operation ECT (enhanced capture timer) -- 16-bit main counter with 7-bit prescaler -- 8 programmable input capture or output compare channels -- Four 8-bit or two 16-bit pulse accumulators 8 PWM (pulse-width modulator) channels -- Programmable period and duty cycle -- 8-bit 8-channel or 16-bit 4-channel -- Separate control for each pulse width and duty cycle -- Center-aligned or left-aligned outputs -- Programmable clock select logic with a wide range of frequencies -- Fast emergency shutdown input Serial interfaces -- SixFourTwo asynchronous serial communication interfaces (SCI) with additional LIN support and selectable IrDA 1.4 return-to-zero-inverted (RZI) format with programmable pulse width -- ThreeTwo Synchronous Serial Peripheral Interfaces (SPI) TwoOne IIC (Inter-IC bus) Modules -- Compatible with IIC bus standard -- Multi-master operation -- Software programmable for one of 256 different serial clock frequencies On-Chip Voltage Regulator -- Two parallel, linear voltage regulators with bandgap reference -- Low-voltage detect (LVD) with low-voltage interrupt (LVI) -- Power-on reset (POR) circuit -- 3.3-V-5.5-V operation -- Low-voltage reset (LVR) -- Ultra low-power wake-up timer 144-pin LQFP, 112-pin LQFP, and 80-pin QFP packages -- I/O lines with 5-V input and drive capability -- Input threshold on external bus interface inputs switchable for 3.3-V or 5-V operation -- 5-V A/D converter inputs -- Operation at 80 MHz equivalent to 40-MHz bus speed MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 33 Chapter 1 Device Overview MC9S12XD-Family * 1.1.2 Development support -- Single-wire background debugTM mode (BDM) -- Four on-chip hardware breakpoints Modes of Operation Normal expanded mode, Emulation of single-chip mode and Emulation of expanded mode are ony available on family members with an external bus interface in 144-pin LQFP. See Appendix E Derivative Differences for package options. User modes: * * Normal and emulation operating modes -- Normal single-chip mode -- Normal expanded mode -- Emulation of single-chip mode -- Emulation of expanded mode Special Operating Modes -- Special single-chip mode with active background debug mode -- Special test mode (Freescale use only) Low-power modes: * System stop modes -- Pseudo stop mode -- Full stop mode * System wait mode 1.1.3 Block Diagram Figure 1-1 shows a block diagram of theMC9S12X-Family. The block diagram shows all modules available on cover part MC9S12XDP512RMV2. Availability of modules on other family members see Appendix E Derivative Differences. Figure 1-2 shows blocks integrated on maskset M42E. The 16 channel ATD Converter is routed to pins PAD00 - PAD15 on maskset M42E. See Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 123. MC9S12XDP512 Data Sheet, Rev. 2.21 34 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family SCI1 SPI0 DDRA PTA Timer 4-Channel 16-Bit with Prescaler for Internal Timebases Non-Multiplexed External Bus Interface (EBI) DDRB DDRC DDRD PTB SCI3 RXD TXD Digital Supply 2.5 V VDD1,2 VSS1,2 PLL Supply 2.5 V VDDPLL VSSPLL Analog Supply 3-5 V VDDA VSSA CAN1 CAN2 CAN3 CAN4 SCI2 IIC1 IIC0 PWM I/O Supply 3-5 V VDDX1,2 VSSX1,2 Voltage Regulator 3-5 V VDDR1,2 VSSR1,2 SCI4 SCI5 RXD TXD RXD TXD SPI1 SPI2 MISO MOSI SCK SS RXCAN TXCAN RXCAN TXCAN RXCAN TXCAN RXCAN TXCAN RXCAN TXCAN RXD TXD SDA SCL SDA SCL PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 MISO MOSI SCK SS MISO MOSI SCK SS KWJ0 KWJ1 KWJ2 KWJ4 KWJ5 KWJ6 KWJ7 KWP0 KWP1 KWP2 KWP3 KWP4 KWP5 KWP6 KWP7 KWH0 KWH1 KWH2 KWH3 KWH4 KWH5 KWH6 KWH7 DDRAD1 & AD1 PTT VRH VRL VDDA VSSA PAD08 PAD09 PAD10 PAD11 PAD12 PAD13 PAD14 PAD15 PAD16 PAD17 PAD18 PAD19 PAD20 PAD21 PAD22 PAD23 PT0 PT1 PT2 PT3 PT4 PT5 PT6 PT7 PS0 PS1 PS2 PS3 PS4 PS5 PS6 PS7 PM0 PM1 PM2 PM3 PM4 PM5 PM6 PM7 PJ0 CS3 PJ1 PJ2 CS1 PJ4 CS0 PJ5 CS2 PJ6 PJ7 PP0 PP1 PP2 PP3 PP4 PP5 PP6 PP7 PH0 PH1 PH2 PH3 PH4 PH5 PH6 PH7 Signals shown in Bold-Italics are neither available on the 112-pin nor on the 80-pin oackage option Signals shown in Bold are not available on the 80-pin package SCI0 DDRT Enhanced Capture Timer PTS XIRQ IRQ R/W/WE LSTRB/LDS/EROMCTL ECLK MODA/RE/TAGLO MODB/TAGHI ECLKX2/XCLKS IQSTAT0 IQSTAT1 IQSTAT2 IQSTAT3 8-Bit PPAGE ACC0 Allows 4-MByte ACC1 Program space ACC2 ROMCTL/EWAIT XGATE Peripheral Co-Processor DDRS Periodic Interrupt COP Watchdog Clock Monitor Breakpoints PTM Enhanced Multilevel Interrupt Module DDRM DDRE DDRK PTE PTK Clock and Reset Generation Module CAN0 PTC UDS ADDR16 ADDR17 ADDR18 ADDR19 ADDR20 ADDR21 ADDR22 EWAIT ADDR15 ADDR14 ADDR13 ADDR12 ADDR11 ADDR10 ADDR9 ADDR8 ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 PE0 PE1 PE2 PE3 PE4 PE5 PE6 PE7 PK0 PK1 PK2 PK3 PK4 PK5 PK6 PK7 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 PLL PTD VDDPLL VSSPLL EXTAL XTAL RESET TEST PTJ CPU12X XFC DDRJ Single-Wire Background Debug Module BKGD PTP Voltage Regulator AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 AN16 AN17 AN18 AN19 AN20 AN21 AN22 AN23 IOC0 IOC1 IOC2 IOC3 IOC4 IOC5 IOC6 IOC7 RXD TXD RXD TXD DDRP VREGEN VDD1,2 VSS1,2 PAD00 PAD01 PAD02 PAD03 PAD04 PAD05 PAD06 PAD07 VRH VRL VDDA VSSA PTH AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 4/2/1-Kbyte EEPROM VDDR VSSR ATD1 DDRH 32/20/16/14/10/8/4-Kbyte RAM VRH VRL VDDA VSSA Module to Port Routing ATD0 DDRAD0 & AD0 512/384/256/128/64-Kbyte Flash Figure 1-1. MC9S12XD-Family Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 35 Chapter 1 Device Overview MC9S12XD-Family XGATE Peripheral Co-Processor SCI1 CAN4 RXCAN TXCAN Digital Supply 2.5 V VDD1,2 VSS1,2 Analog Supply 3-5 V VDDA VSSA IIC0 PWM I/O Supply 3-5 V VDDX VSSX Voltage Regulator 3-5 V VDDR VSSR PTAD1 PJ0 PJ1 DDRJ PLL Supply 2.5 V VDDPLL VSSPLL KWJ0 KWJ1 SPI1 SDA SCL PWM0 PWM1 PWM2 PWM3 PWM4 PWM5 PWM6 PWM7 MISO MOSI SCK SS KWJ6 KWJ7 KWP0 KWP1 KWP2 KWP3 KWP4 KWP5 KWP6 KWP7 KWH0 KWH1 KWH2 KWH3 KWH4 KWH5 KWH6 KWH7 PTJ Timer 4-Channel 16-Bit with Prescaler for Internal Timebases MISO MOSI SCK SS RXCAN CAN0 TXCAN SPI0 PTP 8-Bit PPAGE Allows 4-MByte Program space PTH DDRK DDRA PTK SCI0 DDRP DDRE PTE Enhanced Capture Timer ECLK PAD00 PAD01 PAD02 PAD03 PAD04 PAD05 PAD06 PAD07 PAD08 PAD09 PAD10 PAD11 PAD12 PAD13 PAD14 PAD15 PT0 PT1 PT2 PT3 PT4 PT5 PT6 PT7 PS0 PS1 PS2 PS3 PS4 PS5 PS6 PS7 PM0 PM1 PM2 PM3 PM4 PM5 PM6 PM7 PJ6 PJ7 PP0 PP1 PP2 PP3 PP4 PP5 PP6 PP7 PH0 PH1 PH2 PH3 PH4 PH5 PH6 PH7 Signals shown in Bold-Italics are neither available on the 112-pin nor on the 80-pin oackage option Signals shown in Bold are not available on the 80-pin package Periodic Interrupt COP Watchdog Clock Monitor Breakpoints PTT Enhanced Multilevel Interrupt Module ECLKX2/XCLKS DDRB PK7 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 Clock and Reset Generation Module XIRQ IRQ PTA PE0 PE1 PE2 PE3 PE4 PE5 PE6 PE7 PK0 PK1 PK2 PK3 PK4 PK5 PLL PTB VDDPLL VSSPLL EXTAL XTAL RESET TEST PTS CPU12X XFC DDRH Single-Wire Background Debug Module BKGD PTM Voltage Regulator Module to Port Routing VREGEN VDD1,2 VSS1,2 AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 AN8 AN9 AN10 AN11 AN12 AN13 AN14 AN15 IOC0 IOC1 IOC2 IOC3 IOC4 IOC5 IOC6 IOC7 RXD TXD RXD TXD DDRAD1 2-Kbyte EEPROM VDDR VSSR VRH VRL VDDA VSSA VDDA VSSA DDRT 12 Kbyte RAM VRH VRL DDRS ATD1 DDRM 128-Kbyte Flash Figure 1-2. Block Diagram Maskset M42E MC9S12XDP512 Data Sheet, Rev. 2.21 36 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.1.4 Device Memory Map Table 1-1shows the device register memory map of the MC9S12XDP512. Available modules on other Family members please refer to Appendix E Derivative Differences Unimplemented register space shown in Table 1-1 is not allocated to any module. Writing to these locations have no effect. Read access to these locations returns zero. Figure 1-1 shows the global address mapping for the parts listed in Table 1-2. Table 1-1. Device Register Memory Map Address Module Size (Bytes) 0x0000-0x0009 PIM (port integration module) 10 0x000A-0x000B MMC (memory map control) 2 0x000C-0x000D PIM (port integration module) 2 0x000E-0x000F EBI (external bus interface) 2 0x0010-0x0017 MMC (memory map control) 8 0x0018-0x0019 Unimplemented 2 0x001A-0x001B Device ID register 2 0x001C-0x001F PIM (port integration module) 4 0x0020-0x002F DBG (debug module) 16 0x0030-0x0031 MMC (memory map control) 2 0x0032-0x0033 PIM (port integration module) 2 0x0034-0x003F CRG (clock and reset generator) 12 0x0040-0x007F ECT (enhanced capture timer 16-bit 8-channel)s 64 0x0080-0x00AF ATD1 (analog-to-digital converter 10-bit 16-channel) 48 0x00B0-0x00B7 IIC1 (inter IC bus) 8 0x00B8-0x00C7 Reserved 16 0x00B8-0x00BF SCI2 (serial communications interface) 8 0x00C0-0x00C7 SCI3 (serial communications interface) 8 0x00C8-0x00CF SCI0 (serial communications interface) 8 0x00D0-0x00D7 SCI1 (serial communications interface) 8 0x00D8-0x00DF SPI0 (serial peripheral interface) 8 0x00E0-0x00E7 IIC0 (inter IC bus) 8 0x00E8-0x00EF Unimplemented 8 0x00F0-0x00F7 SPI1 (serial peripheral interface) 8 0x00F8-0x013F Reserved 8 0x00F8-0x00FF SPI2 (serial peripheral interface) 8 0x0100-0x010F Flash control register 16 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 37 Chapter 1 Device Overview MC9S12XD-Family Table 1-1. Device Register Memory Map (continued) Address Module Size (Bytes) 0x0110-0x011B EEPROM control register 12 0x011C-0x011F MMC (memory map control) 4 0x0120-0x012F INT (interrupt module) 16 0x0130-0x013F Reserved 16 0x0130-0x0137 SCI4 (serial communications interface) 8 0x0138-0x013F SCI5 (serial communications interface) 8 0x0140-0x017F CAN0 (scalable CAN) 64 0x0180-0x01BF CAN1 (scalable CAN) 64 0x0180-0x023F Reserved 192 0x01C0-0x01FF CAN2 (scalable CAN) 64 0x0200-0x023F Reserved 64 0x0200-0x023F CAN3 (scalable CAN) 64 0x0240-0x027F PIM (port integration module) 64 0x0280-0x02BF CAN4 (scalable CAN) 64 0x02C0-0x02DF Reserved 32 0x02C0-0x02DF ATD0 (analog-to-digital converter 10 bit 8-channel) 32 0x02E0-0x02EF Unimplemented 16 0x02F0-0x02F7 Voltage regulator 8 0x02F8-0x02FF Unimplemented 8 0x0300-0x0327 PWM (pulse-width modulator 8 channels) 40 0x0328-0x033F Unimplemented 24 0x0340-0x0367 Periodic interrupt timer 40 0x0368-0x037F Unimplemented 24 0x0380-0x03BF XGATE 64 0x03C0-0x03FF Unimplemented 64 0x0400-0x07FF Unimplemented 1024 MC9S12XDP512 Data Sheet, Rev. 2.21 38 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family CPU and BDM Local Memory Map Global Memory Map 0x00_0000 0x00_07FF 2K REGISTERS CS3 Unimplemented RAM 0x0800 0x0C00 0x1000 RAM 2K REGISTERS 1K EEPROM window EPAGE 0x0F_FFFF 1K EEPROM 4K RAM window Unimplemented EEPROM RPAGE CS2 0x0000 RAMSIZE RAM_LOW 8K RAM EEPROM_LOW EEPROM 0x4000 0x13_FFFF CS2 Unpaged 16K FLASH EEPROMSIZE 0x2000 0x1F_FFFF External Space CS1 0x8000 PPAGE 0x3F_FFFF 0xC000 CS0 16K FLASH window Unimplemented FLASH Unpaged 16K FLASH Reset Vectors FLASH_LOW FLASH FLASHSIZE 0xFFFF 0x7F_FFFF Figure 1-3. S12X CPU & BDM Global Address Mapping MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 39 Chapter 1 Device Overview MC9S12XD-Family Table 1-2. Device Internal Resources (see Figure 1-3) RAMSIZE/ RAM_LOW EEPROMSIZE/ EEPROM_LOW FLASHSIZE/ FLASH_LOW 9S12XDP512 32K 0x0F_8000 4K 0x13_F000 512K 0x78_0000 9S12XDT512 20K 0x0F_B000 4K 0x13_F000 512K 0x78_0000 9S12XA512 32K 0x0F_8000 4K 0x13_F000 512K 0x78_0000 9S12XDG128 12K 0x0F_D000 2K 0x13_F800 128K 7E_0000 3S12XDG128 12K 0x0F_D000 2K 0x13_F800 128K 7E_0000 9S12XD128 8K 0x0F_E000 2K 0x13_F800 128K 7E_0000 9S12XD64 4K 0x0F_F000 1K 0x13_FC00 64K 7F_0000 9S12XB128 6K 0x0F_E800 1K 0x13_FC00 128K 7E_0000 9S12XA128 12K 0x0F_D000 2K 0x13_F800 128K 7E_0000 Device MC9S12XDP512 Data Sheet, Rev. 2.21 40 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family CPU and BDM Local Memory Map Global Memory Map 0x00_0000 0x00_07FF 2K REGISTERS CS3 Unimplemented RAM 0x0800 0x0C00 0x1000 RAM 2K REGISTERS 1K EEPROM window EPAGE 0x0F_FFFF 1K EEPROM 4K RAM window Unimplemented EEPROM RPAGE CS2 0x0000 RAMSIZE RAM_LOW 8K RAM EEPROM_LOW EEPROM 0x4000 0x13_FFFF CS2 Unpaged 16K FLASH EEPROMSIZE 0x2000 0x1F_FFFF External Space CS1 0x8000 PPAGE 0x3F_FFFF 0xC000 CS0 16K FLASH window Unimplemented FLASH Unpaged 16K FLASH 0xFFFF Reset Vectors 0x78_0000 Unimplemented FLASH FLASH1_HIGH CS0 FLASH0_LOW FLASHSIZE FLASH0 FLASH1 0x7F_FFFF Figure 1-4. S12X CPU & BDM Global Address Mapping MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 41 Chapter 1 Device Overview MC9S12XD-Family Table 1-3. Device Internal Resources (see Figure 1-4) RAMSIZE/ RAM_LOW EEPROMSIZE/ EEPROM_LOW FLASHSIZE0/ FLASH_LOW FLASHSIZE1/ FLASH_HIGH 9S12XDT384 20K 0x0F_B000 4K 0x13_F000 128K 0x79_FFFF 256K 0x7C_0000 9S12XDQ256 16K 0x0F_C000 4K 0x13_F000 9S12XDT256 16K 0x0F_C000 4K 0x13_F000 9S12XD256 14K 0x0F_C800 4K 0x13_F000 128K 0x79_FFFF 128K 0x7E_0000 9S12XA256 16K 0x0F_C000 4K 0x13_F000 9S12XB256 10K 0x0F_D800 2K 0x13_F800 Device MC9S12XDP512 Data Sheet, Rev. 2.21 42 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family XGATE Local Memory Map Figure 1-5. GATE Global Address Mapping Global Memory Map 0x00_0000 Registers 0x00_07FF XGRAM_LOW 0x0800 RAM 0x0F_FFFF RAMSIZE Registers XGRAMSIZE 0x0000 FLASH RAM 0x78_0800 0xFFFF FLASHSIZE FLASH XGFLASH_HIGH 0x7F_FFFF MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 43 Chapter 1 Device Overview MC9S12XD-Family Table 1-4. XGATE Resources (see Figure 1-5) Device 1 XGRANMSIZE XGRAM_LOW 9S12XDP512 32K 0x0F_8000 9S12XDT512 20K 0x0F_B000 9S12XDT384 20K 0x0F_B000 9S12XA512 32K 0x0F_8000 9S12XDQ256 16K 0x0F_C000 9S12XD256 14K 0x0F_C800 9S12XB256 10K 0x0F_D800 9S12XA256 16K 0x0F_C000 XGFLASHSIZE1 XGFLASH_HIGH 30K 0x78_7FFF Available Flah Memory 30K on all listed parts MC9S12XDP512 Data Sheet, Rev. 2.21 44 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family XGATE Local Memory Map Figure 1-6. XGATE Global Address Mapping Global Memory Map 0x00_0000 Registers 0x00_07FF XGRAM_LOW 0x0800 RAM 0x0F_FFFF RAMSIZE Registers XGRAMSIZE 0x0000 RAM 0xFFFF 0x7F_FFFF MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 45 Chapter 1 Device Overview MC9S12XD-Family Table 1-5. XGATE Resources (see Figure 1-6) Device XGRAMSIZE XGRAM_LOW 9S12XDG128 12K 0x0F_D000 3S12XDG128 12K 0x0F_D000 9S12XD128 8K 0x0F_E000 9S12XD64 4K 0x0F_F000 9S12XB128 6K 0x0F_E800 9S12XA128 12K 0x0F_D000 MC9S12XDP512 Data Sheet, Rev. 2.21 46 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.1.5 Part ID Assignments & Maskset Numbers The part ID is located in two 8-bit registers PARTIDH and PARTIDL (addresses 0x001A and 0x001B). The read-only value is a unique part ID for each revision of the chip. Table 1-6 shows the assigned part ID number and Mask Set number. Table 1-6. Part Names, Masksets and Assigned Part ID Numbers Part Names Mask Set Number Part ID1 MC9S12XDP512 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 MC9S12XDT512 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 MC9S12XA512 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 MC9S12XDT384 MC9S12XDQ256 MC9S12XDT256 0M84E/1M84E 0xC000/0xC001 0L15Y/1L15Y/0M23S 0xC410/0xC4110xC412 0M84E/1M84E 0xC000/0xC001 0xC410/0xC411/0xC412 0M84E/1M84E 0xC000/0xC001 MC9S12XB256 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 0M84E/1M84E 0xC000/0xC001 MC9S12XA256 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 0M84E/1M84E 0xC000/0xC001 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 0M42E/1M42E/2M42E 0xC100/0xC101/0xC102 0L15Y/1L15Y/0M23S 0xC410/0xC4110xC412 0M42E/1M42E/2M42E 0xC100/0xC101/0xC102 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 0M42E/1M42E/2M42E 0xC100/0xC101/0xC102 0L15Y/1L15Y/0M23S 0xC410/0xC411/0xC412 0M42E/1M42E/2M42E 0xC100/0xC101/0xC102 MC9S12XDG128 MC9S12XD128 MC9S12XA128 MC9S12XB128 1.2 0xC410/0xC411/0xC412 0xC410/0xC411/0xC412 0L15Y/1L15Y/0M23S MC9S12XD256 1 0L15Y/1L15Y/0M23S 0L15Y/1L15Y/0M23S The coding is as follows: Bit 15-12: Major family identifier Bit 11-8: Minor family identifier Bit 7-4: Major mask set revision number including FAB transfers Bit 3-0: Minor -- non full -- mask set revision Signal Description This section describes signals that connect off-chip. It includes a pinout diagram, a table of signal properties, and detailed discussion of signals. 1.2.1 Device Pinout The MC9S12XD family of devices offers pin-compatible packaged devices to assist with system development and accommodate expansion of the application. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 47 Chapter 1 Device Overview MC9S12XD-Family The S12XD, S12XA and S12XB family devices are offered in the following packages: * 144-pin LQFP package with an external bus interface (address/data bus) * 112-pin LQFP without external bus interface * 80-pin QFP without external bus interface See Appendix E Derivative Differences for package options. CAUTION Most the I/O Pins have different functionality depending on the module configuration. Not all functions are shown in the following pinouts. Please refer to Table 1-7 for a complete description. For avalability of the modules on different family members refer to Appendix E Derivative Differences. For pinout explanations of the different parts refer to E.7 Pinout explanations: MC9S12XDP512 Data Sheet, Rev. 2.21 48 Freescale Semiconductor 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 PP4/KWP4/PWM4/MISO2 PP5/KPW5/PWM5/MOSI2 PP6/KWP6/PWM6/SS2 PP7/KWP7/PWM7/SCK2 PK7/ROMCTL/EWAIT VDDX1 VSSX1 PM0/RXCAN0 PM1/TXCAN0 PM2/RXCAN1/RXCAN0/MISO0 PM3/TXCAN1/TXCAN0/SS0 PM4/RXCAN2/RXCAN0/RXCAN4/MOSI0 PM5/TXCAN2/TXCAN0/TXCAN4/SCK0 PJ4/KWJ4/SDA1/CS0 PJ5/KWJ5/SCL1/CS2 PJ6/KWJ6/RXCAN4/SDA0/RXCAN0 PJ7/KWJ7/TXCAN4/SCL0/TXCAN0 VREGEN PS7/SS0 PS6/SCK0 PS5/MOSI0 PS4/MISO0 PS3/TXD1 PS2/RXD1 PS1/TXD0 PS0/RXD0 PM6/RXCAN3/RXCAN4/RXD3 PM7/TXCAN3/TXCAN4/TXD3 PAD23/AN23 PAD22/AN22 PAD21/AN21 PAD20/AN20 PAD19/AN19 PAD18/AN18 VSSA VRL Chapter 1 Device Overview MC9S12XD-Family 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 MC9S12XD-Family 144-Pin LQFP Pins shown in BOLD-ITALICS are not available on the 112-Pin LQFP or the 80-Pin QFP package option Pins shown in BOLD are not available on the 80-Pin QFP package option 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 VRH VDDA PAD17/AN17 PAD16/AN16 PAD15/AN15 PAD07/AN07 PAD14/AN14 PAD06/AN06 PAD13/AN13 PAD05/AN05 PAD12/AN12 PAD04/AN04 PAD11/AN11 PAD03/AN03 PAD10/AN10 PAD02/AN02 PAD09/AN09 PAD01/AN01 PAD08/AN08 PAD00/AN00 VSS2 VDD2 PD7/DATA7 PD6/DATA6 PD5/DATA5 PD4/DATA4 VDDR2 VSSR2 PA7/ADDR15 PA6/ADDR14 PA5/ADDR13 PA4/ADDR12 PA3/ADDR11 PA2/ADDR10 PA1/ADDR9 PA0/ADDR8 ADDR5/PB5 ADDR6/PB6 ADDR7/PB7 DATA12/PC4 DATA13/PC5 DATA14/PC6 DATA15/PC7 TXD5/SS2/KWH7/PH7 RXD5/SCK2/KWH6/PH6 TXD4/MOSI2/KWH5/PH5 RXD4/MISO2/KWH4/PH4 XCLKS/ECLKX2/PE7 TAGHI/MODB/PE6 RE/TAGLO/MODA/PE5 ECLK/PE4 VSSR1 VDDR1 RESET VDDPLL XFC VSSPLL EXTAL XTAL TEST SS1/KWH3/PH3 SCK1/KWH2/PH2 MOSI1/KWH1/PH1 MISO1/KWH0/PH0 PD0/DATA0 PD1/DATA1 PD2/DATA2 PD3/DATA3 LDS/LSTRB/PE3/EROMCTL WE/R/W/PE2 IRQ/PE1 XIRQ/PE0 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 SS1/PWM3/KWP3/PP3 SCK1/PWM2/KWP2/PP2 MOSI1/PWM1/KWP1/PP1 MISO1/PWM0/KWP0/PP0 CS1/KWJ2/PJ2 ACC2/ADDR22/PK6 IQSTAT3/ADDR19/PK3 IQSTAT2/ADDR18/PK2 IQSTAT1/ADDR17/PK1 IQSTAT0/ADDR16/PK0 IOC0/PT0 IOC1/PT1 IOC2/PT2 IOC3/PT3 VDD1 VSS1 IOC4/PT4 IOC5/PT5 IOC6/PT6 IOC7/PT7 ACC1/ADDR21/PK5 ACC0/ADDR20/PK4 TXD2/KWJ1/PJ1 CS3/RXD2/KWJ0/PJ0 MODC/BKGD VDDX2 VSSX2 DATA8/PC0 DATA9/PC1 DATA10/PC2 DATA11/PC3 UDS/ADDR0/PB0 ADDR1/PB1 ADDR2/PB2 ADDR3/PB3 ADDR4/PB4 Figure 1-7. MC9S12XD Family Pin Assignment 144-Pin LQFP Package MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 49 MC9S12XD-Family 112-Pin LQFP Pins shown in BOLD are not available on the 80-Pin QFP package option 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 VRH VDDA PAD15/AN15 PAD07/AN07 PAD14/AN14 PAD06/AN06 PAD13/AN13 PAD05/AN05 PAD12/AN12 PAD04/AN04 PAD11/AN11 PAD03/AN03 PAD10/AN10 PAD02/AN02 PAD09/AN09 PAD01/AN01 PAD08/AN08 PAD00/AN00 VSS2 VDD2 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB5 PB6 PB7 TXD5/SS2/KWH7/PH7 RXD5/SCK2/KWH6/PH6 TXD4/MOSI2/KWH5/PH5 RXD4/MISO2/KWH4/PH4 XCLKS/PE7 PE6 PE5 ECLK/PE4 VSSR1 VDDR1 RESET VDDPLL XFC VSSPLL EXTAL XTAL TEST SS1/KWH3/PH3 SCK1/KWH2/PH2 MOSI1/KWH1/PH1 MISO1/KWH0/PH0 PE3 PE2 IRQ/PE1 XIRQ/PE0 SS1/PWM3/KWP3/PP3 SCK1/PWM2/KWP2/PP2 MOSI1/PWM1/KWP1/PP1 MISO1/PWM0/KWP0/PP0 PK3 PK2 PK1 PK0 IOC0/PT0 IOC1/PT1 IOC2/PT2 IOC3/PT3 VDD1 VSS1 IOC4/PT4 IOC5/PT5 IOC6/PT6 IOC7/PT7 PK5 PK4 TXD2/KWJ1/PJ1 RXD2/KWJ0/PJ0 MODC/BKGD PB0 PB1 PB2 PB3 PB4 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 PP4/KWP4/PWM4/MISO2 PP5/KPW5/PWM5/MOSI2 PP6/KWP6/PWM6/SS2 PP7/KWP7/PWM7/SCK2 PK7 VDDX VSSX PM0/RXCAN0 PM1/TXCAN0 PM2/RXCAN1/RXCAN0/MISO0 PM3/TXCAN1/TXCAN0/SS0 PM4/RXCAN2/RXCAN0/RXCAN4/MOS PM5/TXCAN2/TXCAN0/TXCAN4/SCK0 PJ6/KWJ6/RXCAN4/SDA0/RXCAN0 PJ7/KWJ7/TXCAN4/SCL0/TXCAN0 VREGEN PS7/SS0 PS6/SCK0 PS5/MOSI0 PS4/MISO0 PS3/TXD1 PS2/RXD1 PS1/TXD0 PS0/RXD0 PM6/RXCAN3/RXCAN4/RXD3 PM7/TXCAN3/TXCAN4/TXD3 VSSA VRL Chapter 1 Device Overview MC9S12XD-Family Figure 1-8. MC9S12XD Family Pin Assignments 112-Pin LQFP Package MC9S12XDP512 Data Sheet, Rev. 2.21 50 Freescale Semiconductor 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 MC9S12XD-Family 80-Pin QFP 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 VRH VDDA PAD07/AN07 PAD06/AN06 PAD05/AN05 PAD04/AN04 PAD03/AN03 PAD02/AN02 PAD01/AN01 PAD00/AN00 VSS2 VDD2 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB5 PB6 PB7 XCLKS/PE7 PE6 PE5 ECLK/PE4 VSSR1 VDDR1 RESET VDDPLL XFC VSSPLL EXTAL XTAL TEST PE3 PE2 IRQ/PE1 XIRQ/PE0 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 SS1/PWM3/KWP3/PP3 SCK1/PWM2/KWP2/PP2 MOSI1/PWM1/KWP1/PP1 MISO1/PWM0/KWP0/PP0 IOC0/PT0 IOC1/PT1 IOC2/PT2 IOC3/PT3 VDD1 VSS1 IOC4/PT4 IOC5/PT5 IOC6/PT6 IOC7/PT7 MODC/BKGD PB0 PB1 PB2 PB3 PB4 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 PP4/KWP4/PWM4/MISO2 PP5/KWP5/PWM5/MOSI2 PP7/KWP7/PWM7/SCK2 VDDX VSSX PM0/RXCAN0 PM1/TXCAN0 PM2/RXCAN1/RXCAN0/MISO0 PM3/TXCAN1/TXCAN0/SS0 PM4/RXCAN2/RXCAN0/RXCAN4/MOSI0 PM5/TXCAN2/TXCAN0/TXCAN4/SCK0 PJ6/KWJ6/RXCAN4/SDA0/RXCAN0 PJ7/KWJ7/TXCAN4/SCL0/TXCAN0 VREGEN PS3/TXD1 PS2/RXD1 PS1/TXD0 PS0/RXD0 VSSA VRL Chapter 1 Device Overview MC9S12XD-Family Figure 1-9. MC9S12XD Family Pin Assignments 80-Pin QFP Package MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 51 Chapter 1 Device Overview MC9S12XD-Family 1.2.2 Signal Properties Summary Table 1-7 summarizes the pin functionality of the MC9S12XDP512. For available modules on other parts of the S12XD, S12XB and S12XA family please refer to Appendix E Derivative Differences. Table 1-7. Signal Properties Summary (Sheet 1 of 4) Pin Pin Pin Pin Pin Power Name Name Name Name Name Supply Function 1 Function 2 Function 3 Function 4 Function 5 Internal Pull Resistor Description CTRL Reset State EXTAL -- -- -- -- VDDPLL NA NA XTAL -- -- -- -- VDDPLL NA NA RESET -- -- -- -- VDDR TEST -- -- -- -- N.A. RESET pin VREGEN -- -- -- -- VDDX PUCR Up Voltage regulator enable Input PULLUP Oscillator pins External reset DOWN Test input XFC -- -- -- -- VDDPLL NA NA PLL loop filter BKGD MODC -- -- -- VDDX Always on Up Background debug PAD[23:08] AN[23:8] -- -- -- VDDA PER0/ PER1 Disabled Port AD I/O, Port AD inputs of ATD1 and analog inputs of ATD1 PAD[07:00] AN[7:0] -- -- -- VDDA PER1 Disabled Port AD I/O, Port AD inputs of ATD0 and analog inputs of ATD0 PA[7:0] -- -- -- -- VDDR PUCR Disabled Port A I/O PB[7:0] -- -- -- -- VDDR PUCR Disabled Port BI/O PA[7:0] ADDR[15:8] IVD[15:8] -- -- VDDR PUCR Disabled Port A I/O, address bus, internal visibility data PB[7:1] ADDR[7:1] IVD[7:0] -- -- VDDR PUCR Disabled Port B I/O, address bus, internal visibility data PB0 ADDR0 UDS VDDR PUCR Disabled Port B I/O, address bus, upper data strobe PC[7:0] DATA[15:8] -- -- -- VDDR PUCR Disabled Port C I/O, data bus PD[7:0] DATA[7:0] -- -- -- VDDR PUCR Disabled Port D I/O, data bus PE7 ECLKX2 XCLKS -- -- VDDR PUCR PE6 TAGHI MODB -- -- VDDR While RESET pin is low: down Port E I/O, tag high, mode input PE5 RE MODA TAGLO -- VDDR While RESET pin is low: down Port E I/O, read enable, mode input, tag low input Up Port E I/O, system clock output, clock select PE4 ECLK -- -- -- VDDR PUCR Up Port E I/O, bus clock output PE3 LSTRB LDS EROMCTL -- VDDR PUCR Up Port E I/O, low byte data strobe, EROMON control PE2 R/W WE -- -- VDDR PUCR Up Port E I/O, read/write PE1 IRQ -- -- -- VDDR PUCR Up Port E Input, maskable interrupt MC9S12XDP512 Data Sheet, Rev. 2.21 52 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family Table 1-7. Signal Properties Summary (Sheet 2 of 4) Pin Pin Pin Pin Pin Power Name Name Name Name Name Supply Function 1 Function 2 Function 3 Function 4 Function 5 Internal Pull Resistor Description CTRL Reset State PUCR Up PE0 XIRQ -- -- -- VDDR Port E input, non-maskable interrupt PH7 KWH7 SS2 TXD5 -- VDDR PH6 KWH6 SCK2 RXD5 -- VDDR PERH/ PPSH Disabled Port H I/O, interrupt, SCK of SPI2, RXD of SCI5 PH5 KWH5 MOSI2 TXD4 -- VDDR PERH/ PPSH Disabled Port H I/O, interrupt, MOSI of SPI2, TXD of SCI4 PH4 KWH4 MISO2 RXD4 -- VDDR PERH/PPSH Disabled Port H I/O, interrupt, MISO of SPI2, RXD of SCI4 PH3 KWH3 SS1 -- -- VDDR PERH/PPSH Disabled Port H I/O, interrupt, SS of SPI1 PH2 KWH2 SCK1 -- -- VDDR PERH/PPSH Disabled Port H I/O, interrupt, SCK of SPI1 PH1 KWH1 MOSI1 -- -- VDDR PERH/PPSH Disabled Port H I/O, interrupt, MOSI of SPI1 PH0 KWH0 MISO1 -- -- VDDR PERH/PPSH Disabled Port H I/O, interrupt, MISO of SPI1 PJ7 KWJ7 TXCAN4 SCL0 TXCAN0 VDDX PERJ/ PPSJ Up Port J I/O, interrupt, TX of CAN4, SCL of IIC0, TX of CAN0 PJ6 KWJ6 RXCAN4 SDA0 RXCAN0 VDDX PERJ/ PPSJ Up Port J I/O, interrupt, RX of CAN4, SDA of IIC0, RX of CAN0 PJ5 KWJ5 SCL1 CS2 -- VDDX PERJ/ PPSJ Up Port J I/O, interrupt, SCL of IIC1, chip select 2 PJ4 KWJ4 SDA1 CS0 -- VDDX PERJ/ PPSJ Up Port J I/O, interrupt, SDA of IIC1, chip select 0 PJ2 KWJ2 CS1 -- -- VDDX PERJ/ PPSJ Up Port J I/O, interrupt, chip select 1 PJ1 KWJ1 TXD2 -- -- VDDX PERJ/ PPSJ Up Port J I/O, interrupt, TXD of SCI2 PJ0 KWJ0 RXD2 CS3 -- VDDX PERJ/ PPSJ Up Port J I/O, interrupt, RXD of SCI2 PK7 -- -- -- -- VDDX PUCR Up Port K I/O PK[5:4] -- -- -- -- VDDX PUCR Up Port K I/O PK7 EWAIT ROMCTL -- -- VDDX PUCR Up Port K I/O, EWAIT input, ROM on control PK[6:4] ADDR [22:20] ACC[2:0] -- -- VDDX PUCR Up Port K I/O, extended addresses, access source for external access PK3 ADDR19 IQSTAT3 -- -- VDDX PUCR Up Extended address, PIPE status PERH/PPSH Disabled Port H I/O, interrupt, SS of SPI2, TXD of SCI5 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 53 Chapter 1 Device Overview MC9S12XD-Family Table 1-7. Signal Properties Summary (Sheet 3 of 4) Pin Pin Pin Pin Pin Power Name Name Name Name Name Supply Function 1 Function 2 Function 3 Function 4 Function 5 Internal Pull Resistor Description CTRL Reset State PK2 ADDR18 IQSTAT2 -- -- VDDX PUCR Up Extended address, PIPE status PK1 ADDR17 IQSTAT1 -- -- VDDX PUCR Up Extended address, PIPE status PK0 ADDR16 IQSTAT0 -- -- VDDX PUCR Up Extended address, PIPE status PM7 TXCAN3 TXD3 TXCAN4 -- VDDX PERM/ PPSM PM6 RXCAN3 RXD3 RXCAN4 -- VDDX PERM/PPSM Disabled Port M I/O RX of CAN3 and CAN4, RXD of SCI3 PM5 TXCAN2 TXCAN0 TXCAN4 SCK0 VDDX PERM/PPSM Disabled Port M I/O CAN0, CAN2, CAN4, SCK of SPI0 PM4 RXCAN2 RXCAN0 RXCAN4 MOSI0 VDDX PERM/PPSM Disabled Port M I/O, CAN0, CAN2, CAN4, MOSI of SPI0 PM3 TXCAN1 TXCAN0 -- SS0 VDDX PERM/PPSM Disabled Port M I/O TX of CAN1, CAN0, SS of SPI0 PM2 RXCAN1 RXCAN0 -- MISO0 VDDX PERM/PPSM Disabled Port M I/O, RX of CAN1, CAN0, MISO of SPI0 PM1 TXCAN0 -- -- VDDX PERM/PPSM Disabled Port M I/O, TX of CAN0 PM0 RXCAN0 -- -- VDDX PERM/PPSM Disabled Port M I/O, RX of CAN0 PP7 KWP7 PWM7 SCK2 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 7 of PWM, SCK of SPI2 PP6 KWP6 PWM6 SS2 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 6 of PWM, SS of SPI2 PP5 KWP5 PWM5 MOSI2 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 5 of PWM, MOSI of SPI2 PP4 KWP4 PWM4 MISO2 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 4 of PWM, MISO2 of SPI2 PP3 KWP3 PWM3 SS1 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 3 of PWM, SS of SPI1 PP2 KWP2 PWM2 SCK1 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 2 of PWM, SCK of SPI1 PP1 KWP1 PWM1 MOSI1 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 1 of PWM, MOSI of SPI1 PP0 KWP0 PWM0 MISO1 -- VDDX PERP/ PPSP Disabled Port P I/O, interrupt, channel 0 of PWM, MISO2 of SPI1 PS7 SS0 -- -- -- VDDX PERS/ PPSS Up Port S I/O, SS of SPI0 PS6 SCK0 -- -- -- VDDX PERS/ PPSS Up Port S I/O, SCK of SPI0 Disabled Port M I/O, TX of CAN3 and CAN4, TXD of SCI3 MC9S12XDP512 Data Sheet, Rev. 2.21 54 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family Table 1-7. Signal Properties Summary (Sheet 4 of 4) Pin Pin Pin Pin Pin Power Name Name Name Name Name Supply Function 1 Function 2 Function 3 Function 4 Function 5 Internal Pull Resistor Description CTRL Reset State PS5 MOSI0 -- -- -- VDDX PERS/ PPSS Up Port S I/O, MOSI of SPI0 PS4 MISO0 -- -- -- VDDX PERS/ PPSS Up Port S I/O, MISO of SPI0 PS3 TXD1 -- -- -- VDDX PERS/ PPSS Up Port S I/O, TXD of SCI1 PS2 RXD1 -- -- -- VDDX PERS/ PPSS Up Port S I/O, RXD of SCI1 PS1 TXD0 -- -- -- VDDX PERS/ PPSS Up Port S I/O, TXD of SCI0 PS0 RXD0 -- -- -- VDDX PERS/ PPSS Up Port S I/O, RXD of SCI0 PT[7:0] IOC[7:0] -- -- -- VDDX PERT/ PPST Disabled Port T I/O, timer channels NOTE For devices assembled in 80-pin and 112-pin packages all non-bonded out pins should be configured as outputs after reset in order to avoid current drawn from floating inputs. Refer to Table 1-7 for affected pins. 1.2.3 Detailed Signal Descriptions NOTE This section describes all pins which are availabe on the cover part MC9S12XDP512 in 144-pin LQFP package. For modules and pinout explanations of the different family members refer to E.7 Pinout explanations: and E.5 Peripheral Sets S12XD - Family and E.6 Peripheral Sets S12XA & S12XB - Family 1.2.3.1 EXTAL, XTAL -- Oscillator Pins EXTAL and XTAL are the crystal driver and external clock pins. On reset all the device clocks are derived from the EXTAL input frequency. XTAL is the crystal output. 1.2.3.2 RESET -- External Reset Pin The RESET pin is an active low bidirectional control signal. It acts as an input to initialize the MCU to a known start-up state. As an output it is driven ;ow to indicate when any internal MCU reset source triggers. The RESET pin has an internal pullup device. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 55 Chapter 1 Device Overview MC9S12XD-Family 1.2.3.3 TEST -- Test Pin This input only pin is reserved for test. This pin has a pulldown device. NOTE The TEST pin must be tied to VSS in all applications. 1.2.3.4 VREGEN -- Voltage Regulator Enable Pin This input only pin enables or disables the on-chip voltage regulator. The input has a pullup device. 1.2.3.5 XFC -- PLL Loop Filter Pin Please ask your Freescale representative for the interactive application note to compute PLL loop filter elements. Any current leakage on this pin must be avoided. VDDPLL VDDPLL CS MCU R0 CP XFC Figure 1-10. PLL Loop Filter Connections 1.2.3.6 BKGD / MODC -- Background Debug and Mode Pin The BKGD/MODC pin is used as a pseudo-open-drain pin for the background debug communication. It is used as a MCU operating mode select pin during reset. The state of this pin is latched to the MODC bit at the rising edge of RESET. The BKGD pin has a pullup device. 1.2.3.7 PAD[23:8] / AN[23:8] -- Port AD Input Pins of ATD1 PAD[23:8] are general-purpose input or output pins and analog inputs AN[23:8] of the analog-to-digital converter ATD1. 1.2.3.8 PAD[7:0] / AN[7:0] -- Port AD Input Pins of ATD0 PAD[7:0] are general-purpose input or output pins and analog inputs AN[7:0] of the analog-to-digital converter ATD0. 1.2.3.9 PAD[15:0] / AN[15:0] -- Port AD Input Pins of ATD1 PAD[15:0] are general-purpose input or output pins and analog inputs AN[15:0] of the analog-to-digital converter ATD1. MC9S12XDP512 Data Sheet, Rev. 2.21 56 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.2.3.10 PA[7:0] / ADDR[15:8] / IVD[15:8] -- Port A I/O Pins PA[7:0] are general-purpose input or output pins. In MCU expanded modes of operation, these pins are used for the external address bus. In MCU emulation modes of operation, these pins are used for external address bus and internal visibility read data. 1.2.3.11 PB[7:1] / ADDR[7:1] / IVD[7:1] -- Port B I/O Pins PB[7:1] are general-purpose input or output pins. In MCU expanded modes of operation, these pins are used for the external address bus. In MCU emulation modes of operation, these pins are used for external address bus and internal visibility read data. 1.2.3.12 PB0 / ADDR0 / UDS / IVD[0] -- Port B I/O Pin 0 PB0 is a general-purpose input or output pin. In MCU expanded modes of operation, this pin is used for the external address bus ADDR0 or as upper data strobe signal. In MCU emulation modes of operation, this pin is used for external address bus ADDR0 and internal visibility read data IVD0. 1.2.3.13 PB[7:0] -- Port B I/O Pins PB[7:0] are general-purpose input or output pins. 1.2.3.14 PC[7:0] / DATA [15:8] -- Port C I/O Pins PC[7:0] are general-purpose input or output pins. In MCU expanded modes of operation, these pins are used for the external data bus. The input voltage thresholds for PC[7:0] can be configured to reduced levels, to allow data from an external 3.3-V peripheral to be read by the MCU operating at 5.0 V. The input voltage thresholds for PC[7:0] are configured to reduced levels out of reset in expanded and emulation modes. The input voltage thresholds for PC[7:0] are configured to 5-V levels out of reset in normal modes. 1.2.3.15 PD[7:0] / DATA [7:0] -- Port D I/O Pins PD[7:0] are general-purpose input or output pins. In MCU expanded modes of operation, these pins are used for the external data bus. The input voltage thresholds for PD[7:0] can be configured to reduced levels, to allow data from an external 3.3-V peripheral to be read by the MCU operating at 5.0 V. The input voltage thresholds for PD[7:0] are configured to reduced levels out of reset in expanded and emulation modes. The input voltage thresholds for PC[7:0] are configured to 5-V levels out of reset in normal modes. 1.2.3.16 PE7 / ECLKX2 / XCLKS -- Port E I/O Pin 7 PE7 is a general-purpose input or output pin. The XCLKS is an input signal which controls whether a crystal in combination with the internal loop controlled (low power) Pierce oscillator is used or whether full swing Pierce oscillator/external clock circuitry is used. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 57 Chapter 1 Device Overview MC9S12XD-Family The XCLKS signal selects the oscillator configuration during reset low phase while a clock quality check is ongoing. This is the case for: * Power on reset or low-voltage reset * Clock monitor reset * Any reset while in self-clock mode or full stop mode The selected oscillator configuration is frozen with the rising edge of reset. The pin can be configured to drive the internal system clock ECLKX2. EXTAL C1 MCU Crystal or Ceramic Resonator XTAL C2 VSSPLL Figure 1-11. Loop Controlled Pierce Oscillator Connections (PE7 = 1) EXTAL C1 MCU RB RS Crystal or Ceramic Resonator XTAL C2 VSSPLL Figure 1-12. Full Swing Pierce Oscillator Connections (PE7 = 0) EXTAL CMOS-Compatible External Oscillator MCU XTAL Not Connected Figure 1-13. External Clock Connections (PE7 = 0) 1.2.3.17 PE6 / MODB / TAGHI -- Port E I/O Pin 6 PE6 is a general-purpose input or output pin. It is used as a MCU operating mode select pin during reset. The state of this pin is latched to the MODB bit at the rising edge of RESET. This pin is an input with a MC9S12XDP512 Data Sheet, Rev. 2.21 58 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family pull-down device which is only active when RESET is low. TAGHI is used to tag the high half of the instruction word being read into the instruction queue. The input voltage threshold for PE6 can be configured to reduced levels, to allow data from an external 3.3-V peripheral to be read by the MCU operating at 5.0 V. The input voltage threshold for PE6 is configured to reduced levels out of reset in expanded and emulation modes. 1.2.3.18 PE5 / MODA / TAGLO / RE -- Port E I/O Pin 5 PE5 is a general-purpose input or output pin. It is used as a MCU operating mode select pin during reset. The state of this pin is latched to the MODA bit at the rising edge of RESET. This pin is shared with the read enable RE output. This pin is an input with a pull-down device which is only active when RESET is low. TAGLO is used to tag the low half of the instruction word being read into the instruction queue. The input voltage threshold for PE5 can be configured to reduced levels, to allow data from an external 3.3-V peripheral to be read by the MCU operating at 5.0 V. The input voltage threshold for PE5 is configured to reduced levels out of reset in expanded and emulation modes. 1.2.3.19 PE4 / ECLK -- Port E I/O Pin 4 PE4 is a general-purpose input or output pin. It can be configured to drive the internal bus clock ECLK. ECLK can be used as a timing reference. 1.2.3.20 PE3 / LSTRB / LDS / EROMCTL-- Port E I/O Pin 3 PE3 is a general-purpose input or output pin. In MCU expanded modes of operation, LSTRB or LDS can be used for the low byte strobe function to indicate the type of bus access. At the rising edge of RESET the state of this pin is latched to the EROMON bit. 1.2.3.21 PE2 / R/W / WE-- Port E I/O Pin 2 PE2 is a general-purpose input or output pin. In MCU expanded modes of operations, this pin drives the read/write output signal or write enable output signal for the external bus. It indicates the direction of data on the external bus 1.2.3.22 PE[6:2] -- Port E I/O Pins PE[6:2] are general-purpose input or output pins. 1.2.3.23 PE1 / IRQ -- Port E Input Pin 1 PE1 is a general-purpose input pin and the maskable interrupt request input that provides a means of applying asynchronous interrupt requests. This will wake up the MCU from stop or wait mode. 1.2.3.24 PE0 / XIRQ -- Port E Input Pin 0 PE0 is a general-purpose input pin and the non-maskable interrupt request input that provides a means of applying asynchronous interrupt requests. This will wake up the MCU from stop or wait mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 59 Chapter 1 Device Overview MC9S12XD-Family 1.2.3.25 PH7 / KWH7 / SS2 / TXD5 -- Port H I/O Pin 7 PH7 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as slave select pin SS of the serial peripheral interface 2 (SPI2). It can be configured as the transmit pin TXD of serial communication interface 5 (SCI5). 1.2.3.26 PH6 / KWH6 / SCK2 / RXD5 -- Port H I/O Pin 6 PH6 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as serial clock pin SCK of the serial peripheral interface 2 (SPI2). It can be configured as the receive pin (RXD) of serial communication interface 5 (SCI5). 1.2.3.27 PH5 / KWH5 / MOSI2 / TXD4 -- Port H I/O Pin 5 PH5 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of the serial peripheral interface 2 (SPI2). It can be configured as the transmit pin TXD of serial communication interface 4 (SCI4). 1.2.3.28 PH4 / KWH4 / MISO2 / RXD4 -- Port H I/O Pin 4 PH4 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as master input (during master mode) or slave output (during slave mode) pin MISO of the serial peripheral interface 2 (SPI2). It can be configured as the receive pin RXD of serial communication interface 4 (SCI4). 1.2.3.29 PH3 / KWH3 / SS1 -- Port H I/O Pin 3 PH3 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as slave select pin SS of the serial peripheral interface 1 (SPI1). 1.2.3.30 PH2 / KWH2 / SCK1 -- Port H I/O Pin 2 PH2 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as serial clock pin SCK of the serial peripheral interface 1 (SPI1). 1.2.3.31 PH1 / KWH1 / MOSI1 -- Port H I/O Pin 1 PH1 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of the serial peripheral interface 1 (SPI1). MC9S12XDP512 Data Sheet, Rev. 2.21 60 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.2.3.32 PH0 / KWH0 / MISO1 -- Port H I/O Pin 0 PH0 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as master input (during master mode) or slave output (during slave mode) pin MISO of the serial peripheral interface 1 (SPI1). 1.2.3.33 PJ7 / KWJ7 / TXCAN4 / SCL0 / TXCAN0-- PORT J I/O Pin 7 PJ7 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as the transmit pin TXCAN for the scalable controller area network controller 0 or 4 (CAN0 or CAN4) or as the serial clock pin SCL of the IIC0 module. 1.2.3.34 PJ6 / KWJ6 / RXCAN4 / SDA0 / RXCAN0 -- PORT J I/O Pin 6 PJ6 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as the receive pin RXCAN for the scalable controller area network controller 0 or 4 (CAN0 or CAN4) or as the serial data pin SDA of the IIC0 module. 1.2.3.35 PJ5 / KWJ5 / SCL1 / CS2 -- PORT J I/O Pin 5 PJ5 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as the serial clock pin SCL of the IIC1 module. It can be configured to provide a chip-select output. 1.2.3.36 PJ4 / KWJ4 / SDA1 / CS0 -- PORT J I/O Pin 4 PJ4 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as the serial data pin SDA of the IIC1 module. It can be configured to provide a chip-select output. 1.2.3.37 PJ2 / KWJ2 / CS1 -- PORT J I/O Pin 2 PJ2 is a general-purpose input or output pins. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured to provide a chip-select output. 1.2.3.38 PJ1 / KWJ1 / TXD2 -- PORT J I/O Pin 1 PJ1 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as the transmit pin TXD of the serial communication interface 2 (SCI2). 1.2.3.39 PJ0 / KWJ0 / RXD2 / CS3 -- PORT J I/O Pin 0 PJ0 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as the receive pin RXD of the serial communication interface 2 (SCI2).It can be configured to provide a chip-select output. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 61 Chapter 1 Device Overview MC9S12XD-Family 1.2.3.40 PK7 / EWAIT / ROMCTL -- Port K I/O Pin 7 PK7 is a general-purpose input or output pin. During MCU emulation modes and normal expanded modes of operation, this pin is used to enable the Flash EEPROM memory in the memory map (ROMCTL). At the rising edge of RESET, the state of this pin is latched to the ROMON bit. The EWAIT input signal maintains the external bus access until the external device is ready to capture data (write) or provide data (read). The input voltage threshold for PK7 can be configured to reduced levels, to allow data from an external 3.3-V peripheral to be read by the MCU operating at 5.0 V. The input voltage threshold for PK7 is configured to reduced levels out of reset in expanded and emulation modes. 1.2.3.41 PK[6:4] / ADDR[22:20] / ACC[2:0] -- Port K I/O Pin [6:4] PK[6:4] are general-purpose input or output pins. During MCU expanded modes of operation, the ACC[2:0] signals are used to indicate the access source of the bus cycle. This pins also provide the expanded addresses ADDR[22:20] for the external bus. In Emulation modes ACC[2:0] is available and is time multiplexed with the high addresses 1.2.3.42 PK[3:0] / ADDR[19:16] / IQSTAT[3:0] -- Port K I/O Pins [3:0] PK3-PK0 are general-purpose input or output pins. In MCU expanded modes of operation, these pins provide the expanded address ADDR[19:16] for the external bus and carry instruction pipe information. 1.2.3.43 PK7,PK[5:0] -- Port K I/O Pins 7 & [5:0] PK7 and PK[5:0] are general-purpose input or output pins. 1.2.3.44 PM7 / TXCAN3 / TXCAN4 / TXD3 -- Port M I/O Pin 7 PM7 is a general-purpose input or output pin. It can be configured as the transmit pin TXCAN of the scalable controller area network controller 3 or 4 (CAN3 or CAN4). PM7 can be configured as the transmit pin TXD3 of the serial communication interface 3 (SCI3). 1.2.3.45 PM6 / RXCAN3 / RXCAN4 / RXD3 -- Port M I/O Pin 6 PM6 is a general-purpose input or output pin. It can be configured as the receive pin RXCAN of the scalable controller area network controller 3 or 4 (CAN3 or CAN4). PM6 can be configured as the receive pin RXD3 of the serial communication interface 3 (SCI3). 1.2.3.46 PM5 / TXCAN0 / TXCAN2 / TXCAN4 / SCK0 -- Port M I/O Pin 5 PM5 is a general-purpose input or output pin. It can be configured as the transmit pin TXCAN of the scalable controller area network controllers 0, 2 or 4 (CAN0, CAN2, or CAN4). It can be configured as the serial clock pin SCK of the serial peripheral interface 0 (SPI0). MC9S12XDP512 Data Sheet, Rev. 2.21 62 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.2.3.47 PM4 / RXCAN0 / RXCAN2 / RXCAN4 / MOSI0 -- Port M I/O Pin 4 PM4 is a general-purpose input or output pin. It can be configured as the receive pin RXCAN of the scalable controller area network controllers 0, 2, or 4 (CAN0, CAN2, or CAN4). It can be configured as the master output (during master mode) or slave input pin (during slave mode) MOSI for the serial peripheral interface 0 (SPI0). 1.2.3.48 PM3 / TXCAN1 / TXCAN0 / SS0 -- Port M I/O Pin 3 PM3 is a general-purpose input or output pin. It can be configured as the transmit pin TXCAN of the scalable controller area network controllers 1 or 0 (CAN1 or CAN0). It can be configured as the slave select pin SS of the serial peripheral interface 0 (SPI0). 1.2.3.49 PM2 / RXCAN1 / RXCAN0 / MISO0 -- Port M I/O Pin 2 PM2 is a general-purpose input or output pin. It can be configured as the receive pin RXCAN of the scalable controller area network controllers 1 or 0 (CAN1 or CAN0). It can be configured as the master input (during master mode) or slave output pin (during slave mode) MISO for the serial peripheral interface 0 (SPI0). 1.2.3.50 PM1 / TXCAN0 -- Port M I/O Pin 1 PM1 is a general-purpose input or output pin. It can be configured as the transmit pin TXCAN of the scalable controller area network controller 0 (CAN0). 1.2.3.51 PM0 / RXCAN0 -- Port M I/O Pin 0 PM0 is a general-purpose input or output pin. It can be configured as the receive pin RXCAN of the scalable controller area network controller 0 (CAN0). 1.2.3.52 PP7 / KWP7 / PWM7 / SCK2 -- Port P I/O Pin 7 PP7 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 7 output. It can be configured as serial clock pin SCK of the serial peripheral interface 2 (SPI2). 1.2.3.53 PP6 / KWP6 / PWM6 / SS2 -- Port P I/O Pin 6 PP6 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 6 output. It can be configured as slave select pin SS of the serial peripheral interface 2 (SPI2). 1.2.3.54 PP5 / KWP5 / PWM5 / MOSI2 -- Port P I/O Pin 5 PP5 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 5 output. It can MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 63 Chapter 1 Device Overview MC9S12XD-Family be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of the serial peripheral interface 2 (SPI2). 1.2.3.55 PP4 / KWP4 / PWM4 / MISO2 -- Port P I/O Pin 4 PP4 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 4 output. It can be configured as master input (during master mode) or slave output (during slave mode) pin MISO of the serial peripheral interface 2 (SPI2). 1.2.3.56 PP3 / KWP3 / PWM3 / SS1 -- Port P I/O Pin 3 PP3 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 3 output. It can be configured as slave select pin SS of the serial peripheral interface 1 (SPI1). 1.2.3.57 PP2 / KWP2 / PWM2 / SCK1 -- Port P I/O Pin 2 PP2 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 2 output. It can be configured as serial clock pin SCK of the serial peripheral interface 1 (SPI1). 1.2.3.58 PP1 / KWP1 / PWM1 / MOSI1 -- Port P I/O Pin 1 PP1 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 1 output. It can be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of the serial peripheral interface 1 (SPI1). 1.2.3.59 PP0 / KWP0 / PWM0 / MISO1 -- Port P I/O Pin 0 PP0 is a general-purpose input or output pin. It can be configured to generate an interrupt causing the MCU to exit stop or wait mode. It can be configured as pulse width modulator (PWM) channel 0 output. It can be configured as master input (during master mode) or slave output (during slave mode) pin MISO of the serial peripheral interface 1 (SPI1). 1.2.3.60 PS7 / SS0 -- Port S I/O Pin 7 PS7 is a general-purpose input or output pin. It can be configured as the slave select pin SS of the serial peripheral interface 0 (SPI0). 1.2.3.61 PS6 / SCK0 -- Port S I/O Pin 6 PS6 is a general-purpose input or output pin. It can be configured as the serial clock pin SCK of the serial peripheral interface 0 (SPI0). MC9S12XDP512 Data Sheet, Rev. 2.21 64 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.2.3.62 PS5 / MOSI0 -- Port S I/O Pin 5 PS5 is a general-purpose input or output pin. It can be configured as master output (during master mode) or slave input pin (during slave mode) MOSI of the serial peripheral interface 0 (SPI0). 1.2.3.63 PS4 / MISO0 -- Port S I/O Pin 4 PS4 is a general-purpose input or output pin. It can be configured as master input (during master mode) or slave output pin (during slave mode) MOSI of the serial peripheral interface 0 (SPI0). 1.2.3.64 PS3 / TXD1 -- Port S I/O Pin 3 PS3 is a general-purpose input or output pin. It can be configured as the transmit pin TXD of serial communication interface 1 (SCI1). 1.2.3.65 PS2 / RXD1 -- Port S I/O Pin 2 PS2 is a general-purpose input or output pin. It can be configured as the receive pin RXD of serial communication interface 1 (SCI1). 1.2.3.66 PS1 / TXD0 -- Port S I/O Pin 1 PS1 is a general-purpose input or output pin. It can be configured as the transmit pin TXD of serial communication interface 0 (SCI0). 1.2.3.67 PS0 / RXD0 -- Port S I/O Pin 0 PS0 is a general-purpose input or output pin. It can be configured as the receive pin RXD of serial communication interface 0 (SCI0). 1.2.3.68 PT[7:0] / IOC[7:0] -- Port T I/O Pins [7:0] PT[7:0] are general-purpose input or output pins. They can be configured as input capture or output compare pins IOC[7:0] of the enhanced capture timer (ECT). 1.2.4 Power Supply Pins MC9S12XDP512RMV2 power and ground pins are described below. NOTE All VSS pins must be connected together in the application. 1.2.4.1 VDDX1, VDDX2, VSSX1,VSSX2 -- Power and Ground Pins for I/O Drivers External power and ground for I/O drivers. Because fast signal transitions place high, short-duration current demands on the power supply, use bypass capacitors with high-frequency characteristics and place them as close to the MCU as possible. Bypass requirements depend on how heavily the MCU pins are loaded. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 65 Chapter 1 Device Overview MC9S12XD-Family 1.2.4.2 VDDR1, VDDR2, VSSR1, VSSR2 -- Power and Ground Pins for I/O Drivers and for Internal Voltage Regulator External power and ground for I/O drivers and input to the internal voltage regulator. Because fast signal transitions place high, short-duration current demands on the power supply, use bypass capacitors with high-frequency characteristics and place them as close to the MCU as possible. Bypass requirements depend on how heavily the MCU pins are loaded. 1.2.4.3 VDD1, VDD2, VSS1, VSS2 -- Core Power Pins Power is supplied to the MCU through VDD and VSS. Because fast signal transitions place high, short-duration current demands on the power supply, use bypass capacitors with high-frequency characteristics and place them as close to the MCU as possible. This 2.5-V supply is derived from the internal voltage regulator. There is no static load on those pins allowed. The internal voltage regulator is turned off, if VREGEN is tied to ground. NOTE No load allowed except for bypass capacitors. 1.2.4.4 VDDA, VSSA -- Power Supply Pins for ATD and VREG VDDA, VSSA are the power supply and ground input pins for the voltage regulator and the analog-to-digital converters. 1.2.4.5 VRH, VRL -- ATD Reference Voltage Input Pins VRH and VRL are the reference voltage input pins for the analog-to-digital converter. 1.2.4.6 VDDPLL, VSSPLL -- Power Supply Pins for PLL Provides operating voltage and ground for the oscillator and the phased-locked loop. This allows the supply voltage to the oscillator and PLL to be bypassed independently. This 2.5-V voltage is generated by the internal voltage regulator. NOTE No load allowed except for bypass capacitors. MC9S12XDP512 Data Sheet, Rev. 2.21 66 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family Table 1-8. MC9S12XD Family Power and Ground Connection Summary Pin Number Mnemonic Nominal Voltage 144-Pin LQFP 112-Pin LQFP 80-Pin QFP VDD1, 2 15, 87 13, 65 9, 49 2.5 V VSS1, 2 16, 88 14, 66 10, 50 0V VDDR1 53 41 29 5.0 V VSSR1 52 40 28 0V VDDX1 139 107 77 5.0 V VSSX1 138 106 76 0V VDDX2 26 N.A. N.A. 5.0 V VSSX2 27 N.A. N.A. 0V VDDR2 82 N.A. N.A. 5.0 V VSSR2 81 N.A. N.A. 0V VDDA 107 83 59 5.0 V VSSA 110 86 62 0V VRL 109 85 61 0V VRH 108 84 60 5.0 V VDDPLL 55 43 31 2.5 V VSSPLL 57 45 33 0V Description Internal power and ground generated by internal regulator External power and ground, supply to pin drivers and internal voltage regulator External power and ground, supply to pin drivers External power and ground, supply to pin drivers External power and ground, supply to pin drivers Operating voltage and ground for the analog-to-digital converters and the reference for the internal voltage regulator, allows the supply voltage to the A/D to be bypassed independently. Reference voltages for the analog-to-digital converter. Provides operating voltage and ground for the phased-locked loop. This allows the supply voltage to the PLL to be bypassed independently. Internal power and ground generated by internal regulator. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 67 Chapter 1 Device Overview MC9S12XD-Family 1.3 System Clock Description The clock and reset generator module (CRG) provides the internal clock signals for the core and all peripheral modules. Figure 1-12 shows the clock connections from the CRG to all modules. See 79Chapterf or details on clock generation. SCI Modules SPI Modules CAN Modules IIC Modules ATD Modules Bus Clock PIT EXTAL Oscillator Clock ECT CRG PIM XTAL Core Clock RAM S12X XGATE FLASH EEPROM Figure 1-14. MC9S12XD Family Clock Connections The MCU's system clock can be supplied in several ways enabling a range of system operating frequencies to be supported: * The on-chip phase locked loop (PLL) * the PLL self clocking * the oscillator The clock generated by the PLL or oscillator provides the main system clock frequencies core clock and bus clock. As shown in Figure 1-12, this system clocks are used throughout the MCU to drive the core, the memories, and the peripherals. The program Flash memory and the EEPROM are supplied by the bus clock and the oscillator clock.The oscillator clock is used as a time base to derive the program and erase times for the NVM's. See the Flash and EEPROM section for more details on the operation of the NVM's. MC9S12XDP512 Data Sheet, Rev. 2.21 68 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family The CAN modules may be configured to have their clock sources derived either from the bus clock or directly from the oscillator clock. This allows the user to select its clock based on the required jitter performance. Consult MSCAN block description for more details on the operation and configuration of the CAN blocks. In order to ensure the presence of the clock the MCU includes an on-chip clock monitor connected to the output of the oscillator. The clock monitor can be configured to invoke the PLL self-clocking mode or to generate a system reset if it is allowed to time out as a result of no oscillator clock being present. In addition to the clock monitor, the MCU also provides a clock quality checker which performs a more accurate check of the clock. The clock quality checker counts a predetermined number of clock edges within a defined time window to insure that the clock is running. The checker can be invoked following specific events such as on wake-up or clock monitor failure. 1.4 Chip Configuration Summary CAUTION Emulation single chip mode, Normal expanded mode, Emulation expanded mode and ROMCTL/EROMCTL functionality is only available on parts with external bus interface in 144 LQFP package. see Appendix E Derivative Differences. The MCU can operate in six different modes. The different modes, the state of ROMCTL and EROMCTL signal on rising edge of RESET, and the security state of the MCU affects the following device characteristics: * External bus interface configuration * Flash in memory map, or not * Debug features enabled or disabled The operating mode out of reset is determined by the states of the MODC, MODB, and MODA signals during reset (see Table 1-9). The MODC, MODB, and MODA bits in the MODE register show the current operating mode and provide limited mode switching during operation. The states of the MODC, MODB, and MODA signals are latched into these bits on the rising edge of RESET. In normal expanded mode and in emulation modes the ROMON bit and the EROMON bit in the MMCCTL1 register defines if the on chip flash memory is the memory map, or not. (See Table 1-9.) For a detailed description of the ROMON and EROMON bits refer to the S12X_MMC section. The state of the ROMCTL signal is latched into the ROMON bit in the MMCCTL1 register on the rising edge of RESET. The state of the EROMCTL signal is latched into the EROMON bit in the MISC register on the rising edge of RESET. The MCU can operate in two different modes. The operating mode out of reset is determined by the state of the MODC signal during reset. The MODC bit in the MODE register shows the current operating mode and provide limited mode switching during operation. The state of the MODC signal is latched into this bit on the rising edge of RESET. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 69 Chapter 1 Device Overview MC9S12XD-Family Table 1-9. Chip Modes and Data Sources BKGD = MODC PE6 = MODB PE5 = MODA PK7 = ROMCTL PE3 = EROMCTL 1 0 0 X X Internal Special single chip 0 0 0 Emulation single chip 0 0 1 X 0 Emulation memory X 1 Internal Flash 0 X External application 1 X Internal Flash 0 X External application 1 0 Emulation memory 1 1 Internal Flash Chip Modes Normal single chip Normal expanded 1 0 1 Emulation expanded 0 1 1 Special test 1 0 1 0 Data Source1 0 X External application 1 X Internal Flash Internal means resources inside the MCU are read/written. Internal Flash means Flash resources inside the MCU are read/written. Emulation memory means resources inside the emulator are read/written (PRU registers, Flash replacement, RAM, EEPROM, and register space are always considered internal). External application means resources residing outside the MCU are read/written. The configuration of the oscillator can be selected using the XCLKS signal (see Table 1-10). For a detailed description please refer to the S12CRG section. Table 1-10. Clock Selection Based on PE7 PE7 = XCLKS Description 0 Full swing Pierce oscillator or external clock source selected 1 Loop controlled Pierce oscillator selected The logic level on the voltage regulator enable pin VREGEN determines whether the on-chip voltage regulator is enabled or disabled (see Table 1-11). Table 1-11. Voltage Regulator VREGEN VREGEN Description 1 Internal voltage regulator enabled 0 Internal voltage regulator disabled, VDD1,2 and VDDPLL must be supplied externally MC9S12XDP512 Data Sheet, Rev. 2.21 70 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.5 1.5.1 1.5.1.1 Modes of Operation User Modes Normal Expanded Mode Ports K, A, and B are configured as a 23-bit address bus, ports C and D are configured as a 16-bit data bus, and port E provides bus control and status signals. This mode allows 16-bit external memory and peripheral devices to be interfaced to the system. The fastest external bus rate is divide by 2 from the internal bus rate. 1.5.1.2 Normal Single-Chip Mode There is no external bus in this mode. The processor program is executed from internal memory. Ports A, B,C,D, K, and most pins of port E are available as general-purpose I/O. 1.5.1.3 Special Single-Chip Mode This mode is used for debugging single-chip operation, boot-strapping, or security related operations. The background debug module BDM is active in this mode. The CPU executes a monitor program located in an on-chip ROM. BDM firmware is waiting for additional serial commands through the BKGD pin. There is no external bus after reset in this mode. 1.5.1.4 Emulation of Expanded Mode Developers use this mode for emulation systems in which the users target application is normal expanded mode. Code is executed from external memory or from internal memory depending on the state of ROMON and EROMON bit. In this mode the internal operation is visible on external bus interface. 1.5.1.5 Emulation of Single-Chip Mode Developers use this mode for emulation systems in which the user's target application is normal single-chip mode. Code is executed from external memory or from internal memory depending on the state of ROMON and EROMON bit. In this mode the internal operation is visible on external bus interface. 1.5.1.6 Special Test Mode Freescale internal use only. 1.5.2 Low-Power Modes The microcontroller features two main low-power modes. Consult the respective sections for information on the module behavior in system stop, system pseudo stop, and system wait mode. An important source of information about the clock system is the Clock and Reset Generator S12CRG section. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 71 Chapter 1 Device Overview MC9S12XD-Family 1.5.2.1 System Stop Modes The system stop modes are entered if the CPU executes the STOP instruction and the XGATE doesn't execute a thread and the XGFACT bit in the XGMCTL register is cleared. Depending on the state of the PSTP bit in the CLKSEL register the MCU goes into pseudo stop mode or full stop mode. Please refer to CRG section. Asserting RESET, XIRQ, IRQ or any other interrupt ends the system stop modes. 1.5.2.2 Pseudo Stop Mode In this mode the clocks are stopped but the oscillator is still running and the real time interrupt (RTI) or watchdog (COP) submodule can stay active. Other peripherals are turned off. This mode consumes more current than the system stop mode, but the wake up time from this mode is significantly shorter. 1.5.2.3 Full Stop Mode The oscillator is stopped in this mode. All clocks are switched off. All counters and dividers remain frozen. 1.5.2.4 System Wait Mode This mode is entered when the CPU executes the WAI instruction. In this mode the CPU will not execute instructions. The internal CPU clock is switched off. All peripherals and the XGATE can be active in system wait mode. For further power consumption the peripherals can individually turn off their local clocks. Asserting RESET, XIRQ, IRQ or any other interrupt that has not been masked ends system wait mode. 1.5.3 Freeze Mode The enhanced capture timer, pulse width modulator, analog-to-digital converters, the periodic interrupt timer and the XGATE module provide a software programmable option to freeze the module status during the background debug module is active. This is useful when debugging application software. For detailed description of the behavior of the ATD0, ATD1, ECT, PWM, XGATE and PIT when the background debug module is active consult the corresponding sections.. 1.6 Resets and Interrupts Consult the S12XCPU Block Guide for information on exception processing. 1.6.1 Vectors Table 1-12 lists all interrupt sources and vectors in the default order of priority. The interrupt module (S12XINT) provides an interrupt vector base register (IVBR) to relocate the vectors. Associated with each I-bit maskable service request is a configuration register. It selects if the service request is enabled, the service request priority level and whether the service request is handled either by the S12X CPU or by the XGATE module. MC9S12XDP512 Data Sheet, Rev. 2.21 72 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family Table 1-12. Interrupt Vector Locations (Sheet 1 of 3) Vector Address1 XGATE Channel ID2 Interrupt Source CCR Mask Local Enable $FFFE -- System reset or illegal access reset None None $FFFC -- Clock monitor reset None PLLCTL (CME, SCME) $FFFA -- COP watchdog reset None COP rate select Vector base + $F8 -- Unimplemented instruction trap None None Vector base+ $F6 -- SWI None None Vector base+ $F4 -- XIRQ X Bit None Vector base+ $F2 -- IRQ I bit IRQCR (IRQEN) Vector base+ $F0 $78 Real time interrupt I bit CRGINT (RTIE) Vector base+ $EE $77 Enhanced capture timer channel 0 I bit TIE (C0I) Vector base + $EC $76 Enhanced capture timer channel 1 I bit TIE (C1I) Vector base+ $EA $75 Enhanced capture timer channel 2 I bit TIE (C2I) Vector base+ $E8 $74 Enhanced capture timer channel 3 I bit TIE (C3I) Vector base+ $E6 $73 Enhanced capture timer channel 4 I bit TIE (C4I) Vector base+ $E4 $72 Enhanced capture timer channel 5 I bit TIE (C5I) Vector base + $E2 $71 Enhanced capture timer channel 6 I bit TIE (C6I) Vector base+ $E0 $70 Enhanced capture timer channel 7 I bit TIE (C7I) Vector base+ $DE $6F Enhanced capture timer overflow I bit TSRC2 (TOF) Vector base+ $DC $6E Pulse accumulator A overflow I bit PACTL (PAOVI) Vector base + $DA $6D Pulse accumulator input edge I bit PACTL (PAI) Vector base + $D8 $6C SPI0 I bit SPI0CR1 (SPIE, SPTIE) Vector base+ $D6 $6B SCI0 I bit SCI0CR2 (TIE, TCIE, RIE, ILIE) Vector base + $D4 $6A SCI1 I bit SCI1CR2 (TIE, TCIE, RIE, ILIE) Vector base + $D2 $69 ATD0 I bit ATD0CTL2 (ASCIE) Vector base + $D2 Reserved Vector base + $D0 $68 ATD1 I bit ATD1CTL2 (ASCIE) Vector base + $CE $67 Port J I bit PIEJ (PIEJ7-PIEJ0) Vector base + $CC $66 Port H I bit PIEH (PIEH7-PIEH0) Vector base + $CA $65 Modulus down counter underflow I bit MCCTL(MCZI) Vector base + $C8 $64 Pulse accumulator B overflow I bit PBCTL(PBOVI) Vector base + $C6 $63 CRG PLL lock I bit CRGINT(LOCKIE) Vector base + $C4 $62 CRG self-clock mode I bit CRGINT (SCMIE) I bit IBCR0 (IBIE) Vector base + $C2 Vector base + $C0 Reserved $60 IIC0 bus MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 73 Chapter 1 Device Overview MC9S12XD-Family Table 1-12. Interrupt Vector Locations (Sheet 2 of 3) Vector Address1 XGATE Channel ID2 Interrupt Source CCR Mask Local Enable Vector base + $BE $5F SPI1 I bit SPI1CR1 (SPIE, SPTIE) Vector base + $BC $5E SPI2 I bit SPI2CR1 (SPIE, SPTIE) Vector base + $BC RESERVED Vector base + $BA $5D EEPROM I bit ECNFG (CCIE, CBEIE) Vector base + $B8 $5C FLASH I bit FCNFG (CCIE, CBEIE) Vector base + $B6 $5B CAN0 wake-up I bit CAN0RIER (WUPIE) Vector base + $B4 $5A CAN0 errors I bit CAN0RIER (CSCIE, OVRIE) Vector base + $B2 $59 CAN0 receive I bit CAN0RIER (RXFIE) Vector base + $B0 $58 CAN0 transmit I bit CAN0TIER (TXEIE[2:0]) Vector base + $AE $57 CAN1 wake-up I bit CAN1RIER (WUPIE) Vector base + $AC $56 CAN1 errors I bit CAN1RIER (CSCIE, OVRIE) Vector base + $AA $55 CAN1 receive I bit CAN1RIER (RXFIE) Vector base + $A8 $54 CAN1 transmit I bit CAN1TIER (TXEIE[2:0]) Vector base + $A6 $53 CAN2 wake-up I bit CAN2RIER (WUPIE) Vector base + $A4 $52 CAN2 errors I bit CAN2RIER (CSCIE, OVRIE) Vector base + $A2 $51 CAN2 receive I bit CAN2RIER (RXFIE) Vector base + $A0 $50 CAN2 transmit I bit CAN2TIER (TXEIE[2:0]) Vector base + $9E $4F CAN3 wake-up I bit CAN3RIER (WUPIE) Vector base+ $9C $4E CAN3 errors I bit CAN3RIER (CSCIE, OVRIE) Vector base+ $9A $4D CAN3 receive I bit CAN3RIER (RXFIE) Vector base + $98 $4C CAN3 transmit I bit CAN3TIER (TXEIE[2:0]) Vector base + $AE to Vector base + 98 Reserved Vector base + $9E to Vector base + 98 Reserved Vector base + $96 $4B CAN4 wake-up I bit CAN4RIER (WUPIE) Vector base + $94 $4A CAN4 errors I bit CAN4RIER (CSCIE, OVRIE) Vector base + $92 $49 CAN4 receive I bit CAN4RIER (RXFIE) Vector base + $90 $48 CAN4 transmit I bit CAN4TIER (TXEIE[2:0]) Vector base + $8E $47 Port P Interrupt I bit PIEP (PIEP7-PIEP0) Vector base+ $8C $46 PWM emergency shutdown I bit PWMSDN (PWMIE) Vector base + $8A $45 SCI2 I bit SCI2CR2 (TIE, TCIE, RIE, ILIE) MC9S12XDP512 Data Sheet, Rev. 2.21 74 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family Table 1-12. Interrupt Vector Locations (Sheet 3 of 3) Vector Address1 XGATE Channel ID2 Interrupt Source CCR Mask Vector base + $88 $44 SCI3 I bit SCI3CR2 (TIE, TCIE, RIE, ILIE) Vector base + $8A to Vector base + $88 Reserved Vector base + $86 $43 SCI4 I bit SCI4CR2 (TIE, TCIE, RIE, ILIE) Vector base + $84 $42 SCI5 I bit SCI5CR2 (TIE, TCIE, RIE, ILIE) I bit IBCR (IBIE) Vector base + $86 to Vector base + $84 Vector base + $82 Reserved $41 Vector base + $82 Vector base + $80 $40 Low-voltage interrupt (LVI) I bit VREGCTRL (LVIE) Vector base + $7E $3F Autonomous periodical interrupt (API) I bit VREGAPICTRL (APIE) Reserved Vector base + $7A $3D Periodic interrupt timer channel 0 I bit PITINTE (PINTE0) Vector base + $78 $3C Periodic interrupt timer channel 1 I bit PITINTE (PINTE1) Vector base + $76 $3B Periodic interrupt timer channel 2 I bit PITINTE (PINTE2) Vector base + $74 $3A Periodic interrupt timer channel 3 I bit PITINTE (PINTE3) Vector base + $72 $39 XGATE software trigger 0 I bit XGMCTL (XGIE) Vector base + $70 $38 XGATE software trigger 1 I bit XGMCTL (XGIE) Vector base + $6E $37 XGATE software trigger 2 I bit XGMCTL (XGIE) Vector base + $6C $36 XGATE software trigger 3 I bit XGMCTL (XGIE) Vector base + $6A $35 XGATE software trigger 4 I bit XGMCTL (XGIE) Vector base + $68 $34 XGATE software trigger 5 I bit XGMCTL (XGIE) Vector base + $66 $33 XGATE software trigger 6 I bit XGMCTL (XGIE) Vector base + $64 $32 XGATE software trigger 7 I bit XGMCTL (XGIE) Vector base + $62 -- XGATE software error interrupt I bit XGMCTL (XGIE) Vector base + $60 -- S12XCPU RAM access violation I bit RAMWPC (AVIE) -- None Vector base+ $12 to Vector base + $5E Vector base + $10 2 IIC1 Bus Reserved Vector base + $7C 1 Local Enable Reserved -- Spurious interrupt 16 bits vector address based For detailed description of XGATE channel ID refer to XGATE Block Guide MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 75 Chapter 1 Device Overview MC9S12XD-Family 1.6.2 Effects of Reset When a reset occurs, MCU registers and control bits are changed to known start-up states. Refer to the respective module Block Guides for register reset states. 1.6.2.1 I/O Pins Refer to the PIM Block Guide for reset configurations of all peripheral module ports. 1.6.2.2 Memory The RAM array is not initialized out of reset. 1.7 COP Configuration The COP timeout rate bits CR[2:0] and the WCOP bit in the COPCTL register are loaded on rising edge of RESET from the Flash control register FCTL ($0107) located in the Flash EEPROM block. See Table 1-13 and Table 1-14 for coding. The FCTL register is loaded from the Flash configuration field byte at global address $7FFF0E during the reset sequence NOTE If the MCU is secured the COP timeout rate is always set to the longest period (CR[2:0] = 111) after COP reset. Table 1-13. Initial COP Rate Configuration NV[2:0] in FCTL Register CR[2:0] in COPCTL Register 000 111 001 110 010 101 011 100 100 011 101 010 110 001 111 000 Table 1-14. Initial WCOP Configuration NV[3] in FCTL Register WCOP in COPCTL Register 1 0 0 1 MC9S12XDP512 Data Sheet, Rev. 2.21 76 Freescale Semiconductor Chapter 1 Device Overview MC9S12XD-Family 1.8 ATD0 External Trigger Input Connection The ATD_10B8C module includes four external trigger inputs ETRIG0, ETRIG1, ETRIG, and ETRIG3. The external trigger allows the user to synchronize ATD conversion to external trigger events. Table 1-15 shows the connection of the external trigger inputs on MC9S12XDP512RMV2. Table 1-15. ATD0 External Trigger Sources External Trigger Input Connected to . . ETRIG0 Pulse width modulator channel 1 ETRIG1 Pulse width modulator channel 3 ETRIG2 Periodic interrupt timer hardware trigger0 PITTRIG[0]. ETRIG3 Periodic interrupt timer hardware trigger1 PITTRIG[1]. See Section Chapter 5, "Analog-to-Digital Converter (S12ATD10B8CV2) for information about the analog-to-digital converter module. When this section refers to freeze mode this is equivalent to active BDM mode. 1.9 ATD1 External Trigger Input Connection The ATD_10B16C module includes four external trigger inputs ETRIG0, ETRIG1, ETRIG, and ETRIG3. The external trigger feature allows the user to synchronize ATD conversion to external trigger events. Table 1-16 shows the connection of the external trigger inputs on MC9S12XDP512RMV2. Table 1-16. ATD1 External Trigger Sources External Trigger Input Connected to . . ETRIG0 Pulse width modulator channel 1 ETRIG1 Pulse width modulator channel 3 ETRIG2 Periodic interrupt timer hardware trigger0 PITTRIG[0]. ETRIG3 Periodic interrupt timer hardware trigger1 PITTRIG[1]. See Section Chapter 4, "Analog-to-Digital Converter (ATD10B16CV4) Block Description for information about the analog-to-digital converter module. When this section refers to freeze mode this is equivalent to active BDM mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 77 Chapter 1 Device Overview MC9S12XD-Family MC9S12XDP512 Data Sheet, Rev. 2.21 78 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.1 Introduction This specification describes the function of the clocks and reset generator (CRG). 2.1.1 Features The main features of this block are: * Phase locked loop (PLL) frequency multiplier -- Reference divider -- Automatic bandwidth control mode for low-jitter operation -- Automatic frequency lock detector -- Interrupt request on entry or exit from locked condition -- Self clock mode in absence of reference clock * System clock generator -- Clock quality check -- User selectable fast wake-up from Stop in self-clock mode for power saving and immediate program execution -- Clock switch for either oscillator or PLL based system clocks * Computer operating properly (COP) watchdog timer with time-out clear window * System reset generation from the following possible sources: -- Power on reset -- Low voltage reset -- Illegal address reset -- COP reset -- Loss of clock reset -- External pin reset * Real-time interrupt (RTI) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 79 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.1.2 Modes of Operation This subsection lists and briefly describes all operating modes supported by the CRG. * Run mode All functional parts of the CRG are running during normal run mode. If RTI or COP functionality is required, the individual bits of the associated rate select registers (COPCTL, RTICTL) have to be set to a nonzero value. * Wait mode In this mode, the PLL can be disabled automatically depending on the PLLSEL bit in the CLKSEL register. * Stop mode Depending on the setting of the PSTP bit, stop mode can be differentiated between full stop mode (PSTP = 0) and pseudo stop mode (PSTP = 1). -- Full stop mode The oscillator is disabled and thus all system and core clocks are stopped. The COP and the RTI remain frozen. -- Pseudo stop mode The oscillator continues to run and most of the system and core clocks are stopped. If the respective enable bits are set, the COP and RTI will continue to run, or else they remain frozen. * Self clock mode Self clock mode will be entered if the clock monitor enable bit (CME) and the self clock mode enable bit (SCME) are both asserted and the clock monitor in the oscillator block detects a loss of clock. As soon as self clock mode is entered, the CRG starts to perform a clock quality check. Self clock mode remains active until the clock quality check indicates that the required quality of the incoming clock signal is met (frequency and amplitude). Self clock mode should be used for safety purposes only. It provides reduced functionality to the MCU in case a loss of clock is causing severe system conditions. MC9S12XDP512 Data Sheet, Rev. 2.21 80 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.1.3 Block Diagram Figure 2-1 shows a block diagram of the CRG. S12X_MMC Voltage Regulator Illegal Address Reset Power on Reset Low Voltage Reset CRG RESET CM fail Clock Monitor OSCCLK EXTAL Oscillator XTAL COP Timeout XCLKS Reset Generator Clock Quality Checker COP RTI System Reset Bus Clock Core Clock Oscillator Clock Registers XFC VDDPLL VSSPLL PLLCLK PLL Clock and Reset Control Real Time Interrupt PLL Lock Interrupt Self Clock Mode Interrupt Figure 2-1. CRG Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 81 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.2 External Signal Description This section lists and describes the signals that connect off chip. 2.2.1 VDDPLL and VSSPLL -- Operating and Ground Voltage Pins These pins provide operating voltage (VDDPLL) and ground (VSSPLL) for the PLL circuitry. This allows the supply voltage to the PLL to be independently bypassed. Even if PLL usage is not required, VDDPLL and VSSPLL must be connected to properly. 2.2.2 XFC -- External Loop Filter Pin A passive external loop filter must be placed on the XFC pin. The filter is a second-order, low-pass filter that eliminates the VCO input ripple. The value of the external filter network and the reference frequency determines the speed of the corrections and the stability of the PLL. Refer to the device specification for calculation of PLL Loop Filter (XFC) components. If PLL usage is not required, the XFC pin must be tied to VDDPLL. VDDPLL CS CP MCU RS XFC Figure 2-2. PLL Loop Filter Connections 2.2.3 RESET -- Reset Pin RESET is an active low bidirectional reset pin. As an input. it initializes the MCU asynchronously to a known start-up state. As an open-drain output, it indicates that a system reset (internal to the MCU) has been triggered. 2.3 Memory Map and Register Definition This section provides a detailed description of all registers accessible in the CRG. MC9S12XDP512 Data Sheet, Rev. 2.21 82 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.1 Module Memory Map Table 2-1 gives an overview on all CRG registers. Table 2-1. CRG Memory Map Address Offset Use Access 0x_00 CRG Synthesizer Register (SYNR) R/W 0x_01 CRG Reference Divider Register (REFDV) R/W 1 0x_02 CRG Test Flags Register (CTFLG) R/W 0x_03 CRG Flags Register (CRGFLG) R/W 0x_04 CRG Interrupt Enable Register (CRGINT) R/W 0x_05 CRG Clock Select Register (CLKSEL) R/W 0x_06 CRG PLL Control Register (PLLCTL) R/W 0x_07 CRG RTI Control Register (RTICTL) R/W 0x_08 CRG COP Control Register (COPCTL) R/W 0x_09 0x_0A 0x_0B CRG Force and Bypass Test Register CRG Test Control Register (FORBYP)2 (CTCTL)3 CRG COP Arm/Timer Reset (ARMCOP) R/W R/W R/W 1 CTFLG is intended for factory test purposes only. FORBYP is intended for factory test purposes only. 3 CTCTL is intended for factory test purposes only. 2 NOTE Register Address = Base Address + Address Offset, where the Base Address is defined at the MCU level and the Address Offset is defined at the module level. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 83 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2 Register Descriptions This section describes in address order all the CRG registers and their individual bits. Register Name SYNR R Bit 7 6 5 4 3 2 1 Bit 0 0 0 SYN5 SYN4 SYN3 SYN2 SYN1 SYN0 0 0 REFDV5 REFDV4 REFDV3 REFDV2 REFDV1 REFDV0 0 0 0 0 0 0 0 0 RTIF PORF LVRF LOCKIF LOCK TRACK RTIE ILAF 0 0 PLLSEL PSTP CME W REFDV R W CTFLG R W CRGFLG R W CRGINT R W CLKSEL R 0 PLLON AUTO ACQ FSTWKP RTDEC RTR6 RTR5 RTR4 RTR3 WCOP RSBCK 0 0 0 0 0 0 0 1 0 0 R 0 0 W Bit 7 Bit 6 R W RTICTL R W COPCTL R W FORBYP LOCKIE 0 W PLLCTL 0 R PLLWAI 0 SCMIF SCMIE SCM 0 RTIWAI COPWAI PRE PCE SCME RTR2 RTR1 RTR0 CR2 CR1 CR0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 WRTMASK W CTCTL R W ARMCOP = Unimplemented or Reserved Figure 2-3. S12CRGV6 Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 84 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.1 CRG Synthesizer Register (SYNR) The SYNR register controls the multiplication factor of the PLL. If the PLL is on, the count in the loop divider (SYNR) register effectively multiplies up the PLL clock (PLLCLK) from the reference frequency by 2 x (SYNR + 1). PLLCLK will not be below the minimum VCO frequency (fSCM). ( SYNR + 1 ) PLLCLK = 2xOSCCLKx -----------------------------------( REFDV + 1 ) NOTE If PLL is selected (PLLSEL=1), Bus Clock = PLLCLK / 2 Bus Clock must not exceed the maximum operating system frequency. R 7 6 0 0 0 0 W Reset 5 4 3 2 1 0 SYN5 SYN4 SYN3 SYN2 SYN1 SYN0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 2-4. CRG Synthesizer Register (SYNR) Read: Anytime Write: Anytime except if PLLSEL = 1 NOTE Write to this register initializes the lock detector bit and the track detector bit. 2.3.2.2 CRG Reference Divider Register (REFDV) The REFDV register provides a finer granularity for the PLL multiplier steps. The count in the reference divider divides OSCCLK frequency by REFDV + 1. R 7 6 0 0 W Reset 0 0 5 4 3 2 1 0 REFDV5 REFDV4 REFDV3 REFDV2 REFDV1 REFDV0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 2-5. CRG Reference Divider Register (REFDV) Read: Anytime Write: Anytime except when PLLSEL = 1 NOTE Write to this register initializes the lock detector bit and the track detector bit. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 85 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.3 Reserved Register (CTFLG) This register is reserved for factory testing of the CRG module and is not available in normal modes. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 2-6. Reserved Register (CTFLG) Read: Always reads 0x_00 in normal modes Write: Unimplemented in normal modes NOTE Writing to this register when in special mode can alter the CRG fucntionality. 2.3.2.4 CRG Flags Register (CRGFLG) This register provides CRG status bits and flags. 7 R W Reset 6 5 4 RTIF PORF LVRF LOCKIF 0 1 2 0 3 2 LOCK TRACK 0 0 1 SCMIF 0 0 SCM 0 1. PORF is set to 1 when a power on reset occurs. Unaffected by system reset. 2. LVRF is set to 1 when a low-voltage reset occurs. Unaffected by system reset. = Unimplemented or Reserved Figure 2-7. CRG Flags Register (CRGFLG) Read: Anytime Write: Refer to each bit for individual write conditions Table 2-2. CRGFLG Field Descriptions Field Description 7 RTIF Real Time Interrupt Flag -- RTIF is set to 1 at the end of the RTI period. This flag can only be cleared by writing a 1. Writing a 0 has no effect. If enabled (RTIE = 1), RTIF causes an interrupt request. 0 RTI time-out has not yet occurred. 1 RTI time-out has occurred. 6 PORF Power on Reset Flag -- PORF is set to 1 when a power on reset occurs. This flag can only be cleared by writing a 1. Writing a 0 has no effect. 0 Power on reset has not occurred. 1 Power on reset has occurred. MC9S12XDP512 Data Sheet, Rev. 2.21 86 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-2. CRGFLG Field Descriptions (continued) Field Description 5 LVRF Low Voltage Reset Flag -- If low voltage reset feature is not available (see device specification) LVRF always reads 0. LVRF is set to 1 when a low voltage reset occurs. This flag can only be cleared by writing a 1. Writing a 0 has no effect. 0 Low voltage reset has not occurred. 1 Low voltage reset has occurred. 4 LOCKIF PLL Lock Interrupt Flag -- LOCKIF is set to 1 when LOCK status bit changes. This flag can only be cleared by writing a 1. Writing a 0 has no effect.If enabled (LOCKIE = 1), LOCKIF causes an interrupt request. 0 No change in LOCK bit. 1 LOCK bit has changed. 3 LOCK Lock Status Bit -- LOCK reflects the current state of PLL lock condition. This bit is cleared in self clock mode. Writes have no effect. 0 PLL VCO is not within the desired tolerance of the target frequency. 1 PLL VCO is within the desired tolerance of the target frequency. 2 TRACK Track Status Bit -- TRACK reflects the current state of PLL track condition. This bit is cleared in self clock mode. Writes have no effect. 0 Acquisition mode status. 1Tracking mode status. 1 SCMIF Self Clock Mode Interrupt Flag -- SCMIF is set to 1 when SCM status bit changes. This flag can only be cleared by writing a 1. Writing a 0 has no effect. If enabled (SCMIE = 1), SCMIF causes an interrupt request. 0 No change in SCM bit. 1 SCM bit has changed. 0 SCM Self Clock Mode Status Bit -- SCM reflects the current clocking mode. Writes have no effect. 0 MCU is operating normally with OSCCLK available. 1 MCU is operating in self clock mode with OSCCLK in an unknown state. All clocks are derived from PLLCLK running at its minimum frequency fSCM. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 87 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.5 CRG Interrupt Enable Register (CRGINT) This register enables CRG interrupt requests. 7 R W Reset 6 RTIE ILAF 0 1 5 0 0 4 LOCKIE 0 3 2 0 0 0 0 1 SCMIE 0 0 0 0 1. ILAF is set to 1 when an illegal address reset occurs. Unaffected by system reset. Cleared by power on or low voltage reset. = Unimplemented or Reserved Figure 2-8. CRG Interrupt Enable Register (CRGINT) Read: Anytime Write: Anytime Table 2-3. CRGINT Field Descriptions Field Description 7 RTIE Real Time Interrupt Enable Bit 0 Interrupt requests from RTI are disabled. 1 Interrupt will be requested whenever RTIF is set. 6 ILAF Illegal Address Reset Flag -- ILAF is set to 1 when an illegal address reset occurs. Refer to S12XMMC Block Guide for details. This flag can only be cleared by writing a 1. Writing a 0 has no effect. 0 Illegal address reset has not occurred. 1 Illegal address reset has occurred. 4 LOCKIE Lock Interrupt Enable Bit 0 LOCK interrupt requests are disabled. 1 Interrupt will be requested whenever LOCKIF is set. 1 SCMIE Self ClockMmode Interrupt Enable Bit 0 SCM interrupt requests are disabled. 1 Interrupt will be requested whenever SCMIF is set. MC9S12XDP512 Data Sheet, Rev. 2.21 88 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.6 CRG Clock Select Register (CLKSEL) This register controls CRG clock selection. Refer to Figure 2-17 for more details on the effect of each bit. 7 R W Reset 6 PLLSEL PSTP 0 0 5 4 0 0 0 0 3 PLLWAI 0 2 0 1 0 RTIWAI COPWAI 0 0 0 = Unimplemented or Reserved Figure 2-9. CRG Clock Select Register (CLKSEL) Read: Anytime Write: Refer to each bit for individual write conditions Table 2-4. CLKSEL Field Descriptions Field Description 7 PLLSEL PLL Select Bit -- Write anytime. Writing a1 when LOCK = 0 and AUTO = 1, or TRACK = 0 and AUTO = 0 has no effect This prevents the selection of an unstable PLLCLK as SYSCLK. PLLSEL bit is cleared when the MCU enters self clock mode, Stop mode or wait mode with PLLWAI bit set. 0 System clocks are derived from OSCCLK (Bus Clock = OSCCLK / 2). 1 System clocks are derived from PLLCLK (Bus Clock = PLLCLK / 2). 6 PSTP Pseudo Stop Bit Write: Anytime This bit controls the functionality of the oscillator during stop mode. 0 Oscillator is disabled in stop mode. 1 Oscillator continues to run in stop mode (pseudo stop). Note: Pseudo stop mode allows for faster STOP recovery and reduces the mechanical stress and aging of the resonator in case of frequent STOP conditions at the expense of a slightly increased power consumption. 3 PLLWAI PLL Stops in Wait Mode Bit Write: Anytime If PLLWAI is set, the CRG will clear the PLLSEL bit before entering wait mode. The PLLON bit remains set during wait mode, but the PLL is powered down. Upon exiting wait mode, the PLLSEL bit has to be set manually if PLL clock is required. While the PLLWAI bit is set, the AUTO bit is set to 1 in order to allow the PLL to automatically lock on the selected target frequency after exiting wait mode. 0 PLL keeps running in wait mode. 1 PLL stops in wait mode. 1 RTIWAI RTI Stops in Wait Mode Bit Write: Anytime 0 RTI keeps running in wait mode. 1 RTI stops and initializes the RTI dividers whenever the part goes into wait mode. 0 COPWAI COP Stops in Wait Mode Bit Normal modes: Write once Special modes: Write anytime 0 COP keeps running in wait mode. 1 COP stops and initializes the COP counter whenever the part goes into wait mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 89 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.7 CRG PLL Control Register (PLLCTL) This register controls the PLL functionality. R W Reset 7 6 5 4 3 2 1 0 CME PLLON AUTO ACQ FSTWKP PRE PCE SCME 1 1 1 1 0 0 0 1 Figure 2-10. CRG PLL Control Register (PLLCTL) Read: Anytime Write: Refer to each bit for individual write conditions Table 2-5. PLLCTL Field Descriptions Field Description 7 CME Clock Monitor Enable Bit -- CME enables the clock monitor. Write anytime except when SCM = 1. 0 Clock monitor is disabled. 1 Clock monitor is enabled. Slow or stopped clocks will cause a clock monitor reset sequence or self clock mode. Note: Operating with CME = 0 will not detect any loss of clock. In case of poor clock quality, this could cause unpredictable operation of the MCU! Note: In stop mode (PSTP = 0) the clock monitor is disabled independently of the CME bit setting and any loss of external clock will not be detected. Also after wake-up from stop mode (PSTP = 0) with fast wake-up enabled (FSTWKP = 1) the clock monitor is disabled independently of the CME bit setting and any loss of external clock will not be detected. 6 PLLON Phase Lock Loop On Bit -- PLLON turns on the PLL circuitry. In self clock mode, the PLL is turned on, but the PLLON bit reads the last latched value. Write anytime except when PLLSEL = 1. 0 PLL is turned off. 1 PLL is turned on. If AUTO bit is set, the PLL will lock automatically. 5 AUTO Automatic Bandwidth Control Bit -- AUTO selects either the high bandwidth (acquisition) mode or the low bandwidth (tracking) mode depending on how close to the desired frequency the VCO is running. Write anytime except when PLLWAI = 1, because PLLWAI sets the AUTO bit to 1. 0 Automatic mode control is disabled and the PLL is under software control, using ACQ bit. 1 Automatic mode control is enabled and ACQ bit has no effect. 4 ACQ Acquisition Bit Write anytime. If AUTO=1 this bit has no effect. 0 Low bandwidth filter is selected. 1 High bandwidth filter is selected. 3 FSTWKP Fast Wake-up from Full Stop Bit -- FSTWKP enables fast wake-up from full stop mode. Write anytime. If self-clock mode is disabled (SCME = 0) this bit has no effect. 0 Fast wake-up from full stop mode is disabled. 1 Fast wake-up from full stop mode is enabled. When waking up from full stop mode the system will immediately resume operation i self-clock mode (see Section 2.4.1.4, "Clock Quality Checker"). The SCMIF flag will not be set. The system will remain in self-clock mode with oscillator and clock monitor disabled until FSTWKP bit is cleared. The clearing of FSTWKP will start the oscillator, the clock monitor and the clock quality check. If the clock quality check is successful, the CRG will switch all system clocks to OSCCLK. The SCMIF flag will be set. See application examples in Figure 2-23 and Figure 2-24. MC9S12XDP512 Data Sheet, Rev. 2.21 90 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-5. PLLCTL Field Descriptions (continued) Field Description 2 PRE RTI Enable during Pseudo Stop Bit -- PRE enables the RTI during pseudo stop mode. Write anytime. 0 RTI stops running during pseudo stop mode. 1 RTI continues running during pseudo stop mode. Note: If the PRE bit is cleared the RTI dividers will go static while pseudo stop mode is active. The RTI dividers will not initialize like in wait mode with RTIWAI bit set. 1 PCE COP Enable during Pseudo Stop Bit -- PCE enables the COP during pseudo stop mode. Write anytime. 0 COP stops running during pseudo stop mode 1 COP continues running during pseudo stop mode Note: If the PCE bit is cleared, the COP dividers will go static while pseudo stop mode is active. The COP dividers will not initialize like in wait mode with COPWAI bit set. 0 SCME 2.3.2.8 Self Clock Mode Enable Bit Normal modes: Write once Special modes: Write anytime SCME can not be cleared while operating in self clock mode (SCM = 1). 0 Detection of crystal clock failure causes clock monitor reset (see Section 2.5.2, "Clock Monitor Reset"). 1 Detection of crystal clock failure forces the MCU in self clock mode (see Section 2.4.2.2, "Self Clock Mode"). CRG RTI Control Register (RTICTL) This register selects the timeout period for the real time interrupt. R W Reset 7 6 5 4 3 2 1 0 RTDEC RTR6 RTR5 RTR4 RTR3 RTR2 RTR1 RTR0 0 0 0 0 0 0 0 0 Figure 2-11. CRG RTI Control Register (RTICTL) Read: Anytime Write: Anytime NOTE A write to this register initializes the RTI counter. Table 2-6. RTICTL Field Descriptions Field Description 7 RTDEC Decimal or Binary Divider Select Bit -- RTDEC selects decimal or binary based prescaler values. 0 Binary based divider value. See Table 2-7 1 Decimal based divider value. See Table 2-8 6-4 RTR[6:4] Real Time Interrupt Prescale Rate Select Bits -- These bits select the prescale rate for the RTI. See Table 2-7 and Table 2-8. 3-0 RTR[3:0] Real Time Interrupt Modulus Counter Select Bits -- These bits select the modulus counter target value to provide additional granularity.Table 2-7 and Table 2-8 show all possible divide values selectable by the RTICTL register. The source clock for the RTI is OSCCLK. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 91 Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-7. RTI Frequency Divide Rates for RTDEC = 0 RTR[6:4] = RTR[3:0] 000 (OFF) 001 (210) 010 (211) 011 (212) 100 (213) 101 (214) 110 (215) 111 (216) 0000 (/1) OFF* 210 211 212 213 214 215 216 0001 (/2) OFF 2x210 2x211 2x212 2x213 2x214 2x215 2x216 0010 (/3) OFF 3x210 3x211 3x212 3x213 3x214 3x215 3x216 0011 (/4) OFF 4x210 4x211 4x212 4x213 4x214 4x215 4x216 0100 (/5) OFF 5x210 5x211 5x212 5x213 5x214 5x215 5x216 0101 (/6) OFF 6x210 6x211 6x212 6x213 6x214 6x215 6x216 0110 (/7) OFF 7x210 7x211 7x212 7x213 7x214 7x215 7x216 0111 (/8) OFF 8x210 8x211 8x212 8x213 8x214 8x215 8x216 1000 (/9) OFF 9x210 9x211 9x212 9x213 9x214 9x215 9x216 1001 (/10) OFF 10x210 10x211 10x212 10x213 10x214 10x215 10x216 1010 (/11) OFF 11x210 11x211 11x212 11x213 11x214 11x215 11x216 1011 (/12) OFF 12x210 12x211 12x212 12x213 12x214 12x215 12x216 1100 (/13) OFF 13x210 13x211 13x212 13x213 13x214 13x215 13x216 1101 (/14) OFF 14x210 14x211 14x212 14x213 14x214 14x215 14x216 1110 (/15) OFF 15x210 15x211 15x212 15x213 15x214 15x215 15x216 1111 (/16) OFF 16x210 16x211 16x212 16x213 16x214 16x215 16x216 * Denotes the default value out of reset.This value should be used to disable the RTI to ensure future backwards compatibility. MC9S12XDP512 Data Sheet, Rev. 2.21 92 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-8. RTI Frequency Divide Rates for RTDEC = 1 RTR[6:4] = RTR[3:0] 000 (1x103) 001 (2x103) 010 (5x103) 011 (10x103) 100 (20x103) 101 (50x103) 110 (100x103) 111 (200x103) 0000 (/1) 1x103 2x103 5x103 10x103 20x103 50x103 100x103 200x103 0001 (/2) 2x103 4x103 10x103 20x103 40x103 100x103 200x103 400x103 0010 (/3) 3x103 6x103 15x103 30x103 60x103 150x103 300x103 600x103 0011 (/4) 4x103 8x103 20x103 40x103 80x103 200x103 400x103 800x103 0100 (/5) 5x103 10x103 25x103 50x103 100x103 250x103 500x103 1x106 0101 (/6) 6x103 12x103 30x103 60x103 120x103 300x103 600x103 1.2x106 0110 (/7) 7x103 14x103 35x103 70x103 140x103 350x103 700x103 1.4x106 0111 (/8) 8x103 16x103 40x103 80x103 160x103 400x103 800x103 1.6x106 1000 (/9) 9x103 18x103 45x103 90x103 180x103 450x103 900x103 1.8x106 1001 (/10) 10 x103 20x103 50x103 100x103 200x103 500x103 1x106 2x106 1010 (/11) 11 x103 22x103 55x103 110x103 220x103 550x103 1.1x106 2.2x106 1011 (/12) 12x103 24x103 60x103 120x103 240x103 600x103 1.2x106 2.4x106 1100 (/13) 13x103 26x103 65x103 130x103 260x103 650x103 1.3x106 2.6x106 1101 (/14) 14x103 28x103 70x103 140x103 280x103 700x103 1.4x106 2.8x106 1110 (/15) 15x103 30x103 75x103 150x103 300x103 750x103 1.5x106 3x106 1111 (/16) 16x103 32x103 80x103 160x103 320x103 800x103 1.6x106 3.2x106 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 93 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.9 CRG COP Control Register (COPCTL) This register controls the COP (computer operating properly) watchdog. 7 R W WCOP Reset1 6 RSBCK 0 5 4 3 0 0 0 0 0 WRTMASK 0 2 1 0 CR2 CR1 CR0 1. Refer to Device User Guide (Section: CRG) for reset values of WCOP, CR2, CR1, and CR0. = Unimplemented or Reserved Figure 2-12. CRG COP Control Register (COPCTL) Read: Anytime Write: 1. RSBCK: Anytime in special modes; write to "1" but not to "0" in all other modes 2. WCOP, CR2, CR1, CR0: -- Anytime in special modes -- Write once in all other modes Writing CR[2:0] to "000" has no effect, but counts for the "write once" condition. Writing WCOP to "0" has no effect, but counts for the "write once" condition. The COP time-out period is restarted if one these two conditions is true: 1. Writing a nonzero value to CR[2:0] (anytime in special modes, once in all other modes) with WRTMASK = 0. or 2. Changing RSBCK bit from "0" to "1". Table 2-9. COPCTL Field Descriptions Field Description 7 WCOP Window COP Mode Bit -- When set, a write to the ARMCOP register must occur in the last 25% of the selected period. A write during the first 75% of the selected period will reset the part. As long as all writes occur during this window, 0x_55 can be written as often as desired. Once 0x_AA is written after the 0x_55, the time-out logic restarts and the user must wait until the next window before writing to ARMCOP. Table 2-10 shows the duration of this window for the seven available COP rates. 0 Normal COP operation 1 Window COP operation 6 RSBCK COP and RTI Stop in Active BDM Mode Bit 0 Allows the COP and RTI to keep running in active BDM mode. 1 Stops the COP and RTI counters whenever the part is in active BDM mode. MC9S12XDP512 Data Sheet, Rev. 2.21 94 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-9. COPCTL Field Descriptions (continued) Field Description 5 WRTMASK Write Mask for WCOP and CR[2:0] Bit -- This write-only bit serves as a mask for the WCOP and CR[2:0] bits while writing the COPCTL register. It is intended for BDM writing the RSBCK without touching the contents of WCOP and CR[2:0]. 0 Write of WCOP and CR[2:0] has an effect with this write of COPCTL 1 Write of WCOP and CR[2:0] has no effect with this write of COPCTL. (Does not count for "write once".) 2-0 CR[1:0] COP Watchdog Timer Rate Select -- These bits select the COP time-out rate (see Table 2-10). The COP time-out period is OSCCLK period divided by CR[2:0] value. Writing a nonzero value to CR[2:0] enables the COP counter and starts the time-out period. A COP counter time-out causes a system reset. This can be avoided by periodically (before time-out) reinitializing the COP counter via the ARMCOP register. While all of the following four conditions are true the CR[2:0], WCOP bits are ignored and the COP operates at highest time-out period (2 24 cycles) in normal COP mode (Window COP mode disabled): 1) COP is enabled (CR[2:0] is not 000) 2) BDM mode active 3) RSBCK = 0 4) Operation in emulation or special modes Table 2-10. COP Watchdog Rates1 1 CR2 CR1 CR0 OSCCLK Cycles to Time-out 0 0 0 COP disabled 0 0 1 214 0 1 0 216 0 1 1 218 1 0 0 220 1 0 1 222 1 1 0 223 1 1 1 224 OSCCLK cycles are referenced from the previous COP time-out reset (writing 0x_55/0x_AA to the ARMCOP register) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 95 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.10 Reserved Register (FORBYP) NOTE This reserved register is designed for factory test purposes only, and is not intended for general user access. Writing to this register when in special modes can alter the CRG's functionality. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 2-13. Reserved Register (FORBYP) Read: Always read 0x_00 except in special modes Write: Only in special modes 2.3.2.11 Reserved Register (CTCTL) NOTE This reserved register is designed for factory test purposes only, and is not intended for general user access. Writing to this register when in special test modes can alter the CRG's functionality. R 7 6 5 4 3 2 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 2-14. Reserved Register (CTCTL) Read: always read 0x_80 except in special modes Write: only in special modes MC9S12XDP512 Data Sheet, Rev. 2.21 96 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.3.2.12 CRG COP Timer Arm/Reset Register (ARMCOP) This register is used to restart the COP time-out period. 7 6 5 4 3 2 1 0 R 0 0 0 0 0 0 0 0 W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Reset Figure 2-15. ARMCOP Register Diagram Read: Always reads 0x_00 Write: Anytime When the COP is disabled (CR[2:0] = "000") writing to this register has no effect. When the COP is enabled by setting CR[2:0] nonzero, the following applies: Writing any value other than 0x_55 or 0x_AA causes a COP reset. To restart the COP time-out period you must write 0x_55 followed by a write of 0x_AA. Other instructions may be executed between these writes but the sequence (0x_55, 0x_AA) must be completed prior to COP end of time-out period to avoid a COP reset. Sequences of 0x_55 writes or sequences of 0x_AA writes are allowed. When the WCOP bit is set, 0x_55 and 0x_AA writes must be done in the last 25% of the selected time-out period; writing any value in the first 75% of the selected period will cause a COP reset. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 97 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.4 Functional Description 2.4.1 Functional Blocks 2.4.1.1 Phase Locked Loop (PLL) The PLL is used to run the MCU from a different time base than the incoming OSCCLK. For increased flexibility, OSCCLK can be divided in a range of 1 to 16 to generate the reference frequency. This offers a finer multiplication granularity. The PLL can multiply this reference clock by a multiple of 2, 4, 6,... 126,128 based on the SYNR register. [ SYNR + 1 ] PLLCLK = 2 x OSCCLK x -----------------------------------[ REFDV + 1 ] CAUTION Although it is possible to set the two dividers to command a very high clock frequency, do not exceed the specified bus frequency limit for the MCU. If (PLLSEL = 1), Bus Clock = PLLCLK / 2 The PLL is a frequency generator that operates in either acquisition mode or tracking mode, depending on the difference between the output frequency and the target frequency. The PLL can change between acquisition and tracking modes either automatically or manually. The VCO has a minimum operating frequency, which corresponds to the self clock mode frequency fSCM. REFERENCE REFDV <5:0> EXTAL REDUCED CONSUMPTION OSCILLATOR OSCCLK FEEDBACK REFERENCE PROGRAMMABLE DIVIDER XTAL CRYSTAL MONITOR supplied by: LOOP PROGRAMMABLE DIVIDER LOCK LOCK DETECTOR VDDPLL/VSSPLL PDET PHASE DETECTOR UP DOWN CPUMP VCO VDDPLL LOOP FILTER SYN <5:0> VDDPLL/VSSPLL XFC PIN PLLCLK VDD/VSS Figure 2-16. PLL Functional Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 98 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.4.1.1.1 PLL Operation The oscillator output clock signal (OSCCLK) is fed through the reference programmable divider and is divided in a range of 1 to 64 (REFDV + 1) to output the REFERENCE clock. The VCO output clock, (PLLCLK) is fed back through the programmable loop divider and is divided in a range of 2 to 128 in increments of [2 x (SYNR + 1)] to output the FEEDBACK clock. Figure 2-16. The phase detector then compares the FEEDBACK clock, with the REFERENCE clock. Correction pulses are generated based on the phase difference between the two signals. The loop filter then slightly alters the DC voltage on the external filter capacitor connected to XFC pin, based on the width and direction of the correction pulse. The filter can make fast or slow corrections depending on its mode, as described in the next subsection. The values of the external filter network and the reference frequency determine the speed of the corrections and the stability of the PLL. The minimum VCO frequency is reached with the XFC pin forced to VDDPLL. This is the self clock mode frequency. 2.4.1.1.2 Acquisition and Tracking Modes The lock detector compares the frequencies of the FEEDBACK clock, and the REFERENCE clock. Therefore, the speed of the lock detector is directly proportional to the final reference frequency. The circuit determines the mode of the PLL and the lock condition based on this comparison. The PLL filter can be manually or automatically configured into one of two possible operating modes: * Acquisition mode In acquisition mode, the filter can make large frequency corrections to the VCO. This mode is used at PLL start-up or when the PLL has suffered a severe noise hit and the VCO frequency is far off the desired frequency. When in acquisition mode, the TRACK status bit is cleared in the CRGFLG register. * Tracking mode In tracking mode, the filter makes only small corrections to the frequency of the VCO. PLL jitter is much lower in tracking mode, but the response to noise is also slower. The PLL enters tracking mode when the VCO frequency is nearly correct and the TRACK bit is set in the CRGFLG register. The PLL can change the bandwidth or operational mode of the loop filter manually or automatically. In automatic bandwidth control mode (AUTO = 1), the lock detector automatically switches between acquisition and tracking modes. Automatic bandwidth control mode also is used to determine when the PLL clock (PLLCLK) is safe to use as the source for the system and core clocks. If PLL LOCK interrupt requests are enabled, the software can wait for an interrupt request and then check the LOCK bit. If interrupt requests are disabled, software can poll the LOCK bit continuously (during PLL start-up, usually) or at periodic intervals. In either case, only when the LOCK bit is set, is the PLLCLK clock safe to use as the source for the system and core clocks. If the PLL is selected as the source for the system and core clocks and the LOCK bit is clear, the PLL has suffered a severe noise hit and the software must take appropriate action, depending on the application. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 99 Chapter 2 Clocks and Reset Generator (S12CRGV6) The following conditions apply when the PLL is in automatic bandwidth control mode (AUTO = 1): * The TRACK bit is a read-only indicator of the mode of the filter. * The TRACK bit is set when the VCO frequency is within a certain tolerance, trk, and is clear when the VCO frequency is out of a certain tolerance, unt. * The LOCK bit is a read-only indicator of the locked state of the PLL. * The LOCK bit is set when the VCO frequency is within a certain tolerance, Lock, and is cleared when the VCO frequency is out of a certain tolerance, unl. * Interrupt requests can occur if enabled (LOCKIE = 1) when the lock condition changes, toggling the LOCK bit. The PLL can also operate in manual mode (AUTO = 0). Manual mode is used by systems that do not require an indicator of the lock condition for proper operation. Such systems typically operate well below the maximum system frequency (fsys) and require fast start-up. The following conditions apply when in manual mode: * ACQ is a writable control bit that controls the mode of the filter. Before turning on the PLL in manual mode, the ACQ bit should be asserted to configure the filter in acquisition mode. * After turning on the PLL by setting the PLLON bit software must wait a given time (tacq) before entering tracking mode (ACQ = 0). * After entering tracking mode software must wait a given time (tal) before selecting the PLLCLK as the source for system and core clocks (PLLSEL = 1). 2.4.1.2 System Clocks Generator PLLSEL or SCM PHASE LOCK LOOP PLLCLK STOP 1 SYSCLK /2 SCM EXTAL 1 OSCILLATOR CORE CLOCK 0 WAIT(RTIWAI), STOP(PSTP,PRE), RTI ENABLE BUS CLOCK RTI OSCCLK 0 XTAL CLOCK PHASE GENERATOR WAIT(COPWAI), STOP(PSTP,PCE), COP ENABLE COP CLOCK MONITOR GATING CONDITION STOP OSCILLATOR CLOCK = CLOCK GATE Figure 2-17. System Clocks Generator MC9S12XDP512 Data Sheet, Rev. 2.21 100 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) The clock generator creates the clocks used in the MCU (see Figure 2-17). The gating condition placed on top of the individual clock gates indicates the dependencies of different modes (STOP, WAIT) and the setting of the respective configuration bits. The peripheral modules use the bus clock. Some peripheral modules also use the oscillator clock. The memory blocks use the bus clock. If the MCU enters self clock mode (see Section 2.4.2.2, "Self Clock Mode") oscillator clock source is switched to PLLCLK running at its minimum frequency fSCM. The bus clock is used to generate the clock visible at the ECLK pin. The core clock signal is the clock for the CPU. The core clock is twice the bus clock as shown in Figure 2-18. But note that a CPU cycle corresponds to one bus clock. PLL clock mode is selected with PLLSEL bit in the CLKSEL registerr. When selected, the PLL output clock drives SYSCLK for the main system including the CPU and peripherals. The PLL cannot be turned off by clearing the PLLON bit, if the PLL clock is selected. When PLLSEL is changed, it takes a maximum of 4 OSCCLK plus 4 PLLCLK cycles to make the transition. During the transition, all clocks freeze and CPU activity ceases. CORE CLOCK BUS CLOCK / ECLK Figure 2-18. Core Clock and Bus Clock Relationship 2.4.1.3 Clock Monitor (CM) If no OSCCLK edges are detected within a certain time, the clock monitor within the oscillator block generates a clock monitor fail event. The CRG then asserts self clock mode or generates a system reset depending on the state of SCME bit. If the clock monitor is disabled or the presence of clocks is detected no failure is indicated by the oscillator block.The clock monitor function is enabled/disabled by the CME control bit. 2.4.1.4 Clock Quality Checker The clock monitor performs a coarse check on the incoming clock signal. The clock quality checker provides a more accurate check in addition to the clock monitor. A clock quality check is triggered by any of the following events: * Power on reset (POR) * Low voltage reset (LVR) * Wake-up from full stop mode (exit full stop) * Clock monitor fail indication (CM fail) A time window of 50,000 VCO clock cycles1 is called check window. 1. VCO clock cycles are generated by the PLL when running at minimum frequency fSCM. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 101 Chapter 2 Clocks and Reset Generator (S12CRGV6) A number greater equal than 4096 rising OSCCLK edges within a check window is called osc ok. Note that osc ok immediately terminates the current check window. See Figure 2-19 as an example. check window 1 3 2 50000 49999 VCO Clock 1 2 3 4 5 4096 OSCCLK 4095 osc ok Figure 2-19. Check Window Example The sequence for clock quality check is shown in Figure 2-20. CM fail Clock OK no exit full stop POR SCME = 1 & FSTWKP = 1 ? LVR yes num = 0 FSTWKP = 0 ? Enter SCM yes no Clock Monitor Reset Enter SCM num = 50 yes check window SCM active? num=num-1 yes osc ok num = 0 no no ? num > 0 ? yes no SCME=1 ? no yes SCM active? yes Switch to OSCCLK no Exit SCM Figure 2-20. Sequence for Clock Quality Check MC9S12XDP512 Data Sheet, Rev. 2.21 102 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) NOTE Remember that in parallel to additional actions caused by self clock mode or clock monitor reset1 handling the clock quality checker continues to check the OSCCLK signal. The clock quality checker enables the PLL and the voltage regulator (VREG) anytime a clock check has to be performed. An ongoing clock quality check could also cause a running PLL (fSCM) and an active VREG during pseudo stop mode or wait mode. 2.4.1.5 Computer Operating Properly Watchdog (COP) The COP (free running watchdog timer) enables the user to check that a program is running and sequencing properly. When the COP is being used, software is responsible for keeping the COP from timing out. If the COP times out it is an indication that the software is no longer being executed in the intended sequence; thus a system reset is initiated (see Section 2.4.1.5, "Computer Operating Properly Watchdog (COP)"). The COP runs with a gated OSCCLK. Three control bits in the COPCTL register allow selection of seven COP time-out periods. When COP is enabled, the program must write 0x_55 and 0x_AA (in this order) to the ARMCOP register during the selected time-out period. Once this is done, the COP time-out period is restarted. If the program fails to do this and the COP times out, the part will reset. Also, if any value other than 0x_55 or 0x_AA is written, the part is immediately reset. Windowed COP operation is enabled by setting WCOP in the COPCTL register. In this mode, writes to the ARMCOP register to clear the COP timer must occur in the last 25% of the selected time-out period. A premature write will immediately reset the part. If PCE bit is set, the COP will continue to run in pseudo stop mode. 2.4.1.6 Real Time Interrupt (RTI) The RTI can be used to generate a hardware interrupt at a fixed periodic rate. If enabled (by setting RTIE = 1), this interrupt will occur at the rate selected by the RTICTL register. The RTI runs with a gated OSCCLK. At the end of the RTI time-out period the RTIF flag is set to 1 and a new RTI time-out period starts immediately. A write to the RTICTL register restarts the RTI time-out period. If the PRE bit is set, the RTI will continue to run in pseudo stop mode. 2.4.2 2.4.2.1 Operating Modes Normal Mode The CRG block behaves as described within this specification in all normal modes. 1. A Clock Monitor Reset will always set the SCME bit to logical 1. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 103 Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.4.2.2 Self Clock Mode The VCO has a minimum operating frequency, fSCM. If the external clock frequency is not available due to a failure or due to long crystal start-up time, the bus clock and the core clock are derived from the VCO running at minimum operating frequency; this mode of operation is called self clock mode. This requires CME = 1 and SCME = 1. If the MCU was clocked by the PLL clock prior to entering self clock mode, the PLLSEL bit will be cleared. If the external clock signal has stabilized again, the CRG will automatically select OSCCLK to be the system clock and return to normal mode. Section 2.4.1.4, "Clock Quality Checker" for more information on entering and leaving self clock mode. NOTE In order to detect a potential clock loss the CME bit should be always enabled (CME = 1)! If CME bit is disabled and the MCU is configured to run on PLL clock (PLLCLK), a loss of external clock (OSCCLK) will not be detected and will cause the system clock to drift towards the VCO's minimum frequency fSCM. As soon as the external clock is available again the system clock ramps up to its PLL target frequency. If the MCU is running on external clock any loss of clock will cause the system to go static. 2.4.3 Low Power Options This section summarizes the low power options available in the CRG. 2.4.3.1 Run Mode The RTI can be stopped by setting the associated rate select bits to 0. The COP can be stopped by setting the associated rate select bits to 0. 2.4.3.2 Wait Mode The WAI instruction puts the MCU in a low power consumption stand-by mode depending on setting of the individual bits in the CLKSEL register. All individual wait mode configuration bits can be superposed. This provides enhanced granularity in reducing the level of power consumption during wait mode. Table 2-11 lists the individual configuration bits and the parts of the MCU that are affected in wait mode . Table 2-11. MCU Configuration During Wait Mode PLLWAI RTIWAI COPWAI PLL Stopped -- -- RTI -- Stopped -- COP -- -- Stopped After executing the WAI instruction the core requests the CRG to switch MCU into wait mode. The CRG then checks whether the PLLWAI bit is asserted (Figure 2-21). Depending on the configuration, the CRG switches the system and core clocks to OSCCLK by clearing the PLLSEL bit and disables the PLL. As soon as all clocks are switched off wait mode is active. MC9S12XDP512 Data Sheet, Rev. 2.21 104 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) CPU Req's Wait Mode. PLLWAI=1 ? No Yes Clear PLLSEL, Disable PLL No Enter Wait Mode CME=1 ? Wait Mode left due to external reset No Yes Exit Wait w. ext.RESET CM Fail ? INT ? Yes No Yes Exit Wait w. CMRESET No SCME=1 ? Yes SCMIE=1 ? Generate SCM Interrupt (Wakeup from Wait) No Exit Wait Mode Yes Exit Wait Mode SCM=1 ? No Yes Enter SCM Enter SCM Continue w. Normal OP Figure 2-21. Wait Mode Entry/Exit Sequence MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 105 Chapter 2 Clocks and Reset Generator (S12CRGV6) There are four different scenarios for the CRG to restart the MCU from wait mode: * External reset * Clock monitor reset * COP reset * Any interrupt If the MCU gets an external reset or COP reset during wait mode active, the CRG asynchronously restores all configuration bits in the register space to its default settings and starts the reset generator. After completing the reset sequence processing begins by fetching the normal or COP reset vector. Wait mode is left and the MCU is in run mode again. If the clock monitor is enabled (CME = 1) the MCU is able to leave wait mode when loss of oscillator/external clock is detected by a clock monitor fail. If the SCME bit is not asserted the CRG generates a clock monitor fail reset (CMRESET). The CRG's behavior for CMRESET is the same compared to external reset, but another reset vector is fetched after completion of the reset sequence. If the SCME bit is asserted the CRG generates a SCM interrupt if enabled (SCMIE = 1). After generating the interrupt the CRG enters self-clock mode and starts the clock quality checker (Section 2.4.1.4, "Clock Quality Checker"). Then the MCU continues with normal operation.If the SCM interrupt is blocked by SCMIE = 0, the SCMIF flag will be asserted and clock quality checks will be performed but the MCU will not wake-up from wait-mode. If any other interrupt source (e.g., RTI) triggers exit from wait mode, the MCU immediately continues with normal operation. If the PLL has been powered-down during wait mode, the PLLSEL bit is cleared and the MCU runs on OSCCLK after leaving wait mode. The software must manually set the PLLSEL bit again, in order to switch system and core clocks to the PLLCLK. If wait mode is entered from self-clock mode the CRG will continue to check the clock quality until clock check is successful. The PLL and voltage regulator (VREG) will remain enabled. Table 2-12 summarizes the outcome of a clock loss while in wait mode. 2.4.3.3 System Stop Mode All clocks are stopped in STOP mode, dependent of the setting of the PCE, PRE, and PSTP bit. The oscillator is disabled in STOP mode unless the PSTP bit is set. All counters and dividers remain frozen but do not initialize. If the PRE or PCE bits are set, the RTI or COP continues to run in pseudo stop mode. In addition to disabling system and core clocks the CRG requests other functional units of the MCU (e.g., voltage-regulator) to enter their individual power saving modes (if available). This is the main difference between pseudo stop mode and wait mode. If the PLLSEL bit is still set when entering stop mode, the CRG will switch the system and core clocks to OSCCLK by clearing the PLLSEL bit. Then the CRG disables the PLL, disables the core clock and finally disables the remaining system clocks. As soon as all clocks are switched off, stop mode is active. If pseudo stop mode (PSTP = 1) is entered from self-clock mode, the CRG will continue to check the clock quality until clock check is successful. The PLL and the voltage regulator (VREG) will remain enabled. If full stop mode (PSTP = 0) is entered from self-clock mode, an ongoing clock quality check will be stopped. A complete timeout window check will be started when stop mode is left again. Wake-up from stop mode also depends on the setting of the PSTP bit. MC9S12XDP512 Data Sheet, Rev. 2.21 106 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-12. Outcome of Clock Loss in Wait Mode CME SCME SCMIE 0 X X Clock failure --> No action, clock loss not detected. 1 0 X Clock failure --> CRG performs Clock Monitor Reset immediately 0 Clock failure --> Scenario 1: OSCCLK recovers prior to exiting wait mode. - MCU remains in wait mode, - VREG enabled, - PLL enabled, - SCM activated, - Start clock quality check, - Set SCMIF interrupt flag. Some time later OSCCLK recovers. - CM no longer indicates a failure, - 4096 OSCCLK cycles later clock quality check indicates clock o.k., - SCM deactivated, - PLL disabled depending on PLLWAI, - VREG remains enabled (never gets disabled in wait mode). - MCU remains in wait mode. Some time later either a wakeup interrupt occurs (no SCM interrupt) - Exit wait mode using OSCCLK as system clock (SYSCLK), - Continue normal operation. or an External Reset is applied. - Exit wait mode using OSCCLK as system clock, - Start reset sequence. Scenario 2: OSCCLK does not recover prior to exiting wait mode. - MCU remains in wait mode, - VREG enabled, - PLL enabled, - SCM activated, - Start clock quality check, - Set SCMIF interrupt flag, - Keep performing clock quality checks (could continue infinitely) while in wait mode. Some time later either a wakeup interrupt occurs (no SCM interrupt) - Exit wait mode in SCM using PLL clock (fSCM) as system clock, - Continue to perform additional clock quality checks until OSCCLK is o.k. again. or an External RESET is applied. - Exit wait mode in SCM using PLL clock (fSCM) as system clock, - Start reset sequence, - Continue to perform additional clock quality checks until OSCCLKis o.k.again. 1 Clock failure --> - VREG enabled, - PLL enabled, - SCM activated, - Start clock quality check, - SCMIF set. SCMIF generates self clock mode wakeup interrupt. - Exit wait mode in SCM using PLL clock (fSCM) as system clock, - Continue to perform a additional clock quality checks until OSCCLK is o.k. again. 1 1 1 1 CRG Actions MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 107 Chapter 2 Clocks and Reset Generator (S12CRGV6) Core req's Stop Mode. Clear PLLSEL, Disable PLL Exit Stop w. ext.RESET Stop Mode left due to external reset No INT ? Yes No Enter Stop Mode PSTP=1 ? Yes CME=1 ? No Yes SCME=1 & FSTWKP=1 ? No INT ? Yes Yes CM fail ? No No Yes No Exit Stop w. CMRESET No SCME=1 ? Yes Clock OK ? Exit Stop w. CMRESET SCME=1 ? Yes Yes Exit Stop Mode Exit Stop Mode no Exit Stop Mode SCMIE=1 ? Generate SCM Interrupt (Wakeup from Stop) No Exit Stop Mode Yes Exit Stop Mode No SCM=1 ? Yes Enter SCM Enter SCM SCMIF not set! Enter SCM Enter SCM Continue w. normal OP Figure 2-22. Stop Mode Entry/Exit Sequence MC9S12XDP512 Data Sheet, Rev. 2.21 108 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.4.3.3.1 Wake-up from Pseudo Stop Mode (PSTP=1) Wake-up from pseudo stop mode is the same as wake-up from wait mode. There are also four different scenarios for the CRG to restart the MCU from pseudo stop mode: * External reset * Clock monitor fail * COP reset * Wake-up interrupt If the MCU gets an external reset or COP reset during pseudo stop mode active, the CRG asynchronously restores all configuration bits in the register space to its default settings and starts the reset generator. After completing the reset sequence processing begins by fetching the normal or COP reset vector. pseudo stop mode is left and the MCU is in run mode again. If the clock monitor is enabled (CME = 1), the MCU is able to leave pseudo stop mode when loss of oscillator/external clock is detected by a clock monitor fail. If the SCME bit is not asserted the CRG generates a clock monitor fail reset (CMRESET). The CRG's behavior for CMRESET is the same compared to external reset, but another reset vector is fetched after completion of the reset sequence. If the SCME bit is asserted the CRG generates a SCM interrupt if enabled (SCMIE = 1). After generating the interrupt the CRG enters self-clock mode and starts the clock quality checker (Section 2.4.1.4, "Clock Quality Checker"). Then the MCU continues with normal operation. If the SCM interrupt is blocked by SCMIE=0, the SCMIF flag will be asserted but the CRG will not wake-up from pseudo stop mode. If any other interrupt source (e.g., RTI) triggers exit from pseudo stop mode, the MCU immediately continues with normal operation. Because the PLL has been powered-down during stop mode, the PLLSEL bit is cleared and the MCU runs on OSCCLK after leaving stop mode. The software must set the PLLSEL bit again, in order to switch system and core clocks to the PLLCLK. Table 2-13 summarizes the outcome of a clock loss while in pseudo stop mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 109 Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-13. Outcome of Clock Loss in Pseudo Stop Mode CME SCME SCMIE 0 X X Clock failure --> No action, clock loss not detected. 1 0 X Clock failure --> CRG performs Clock Monitor Reset immediately 0 Clock Monitor failure --> Scenario 1: OSCCLK recovers prior to exiting pseudo stop mode. - MCU remains in pseudo stop mode, - VREG enabled, - PLL enabled, - SCM activated, - Start clock quality check, - Set SCMIF interrupt flag. Some time later OSCCLK recovers. - CM no longer indicates a failure, - 4096 OSCCLK cycles later clock quality check indicates clock o.k., - SCM deactivated, - PLL disabled, - VREG disabled. - MCU remains in pseudo stop mode. Some time later either a wakeup interrupt occurs (no SCM interrupt) - Exit pseudo stop mode using OSCCLK as system clock (SYSCLK), - Continue normal operation. or an External Reset is applied. - Exit pseudo stop mode using OSCCLK as system clock, - Start reset sequence. Scenario 2: OSCCLK does not recover prior to exiting pseudo stop mode. - MCU remains in pseudo stop mode, - VREG enabled, - PLL enabled, - SCM activated, - Start clock quality check, - Set SCMIF interrupt flag, - Keep performing clock quality checks (could continue infinitely) while in pseudo stop mode. Some time later either a wakeup interrupt occurs (no SCM interrupt) - Exit pseudo stop mode in SCM using PLL clock (fSCM) as system clock - Continue to perform additional clock quality checks until OSCCLK is o.k. again. or an External RESET is applied. - Exit pseudo stop mode in SCM using PLL clock (fSCM) as system clock - Start reset sequence, - Continue to perform additional clock quality checks until OSCCLK is o.k.again. 1 Clock failure --> - VREG enabled, - PLL enabled, - SCM activated, - Start clock quality check, - SCMIF set. SCMIF generates self clock mode wakeup interrupt. - Exit pseudo stop mode in SCM using PLL clock (fSCM) as system clock, - Continue to perform a additional clock quality checks until OSCCLK is o.k. again. 1 1 1 1 CRG Actions MC9S12XDP512 Data Sheet, Rev. 2.21 110 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.4.3.3.2 Wake-up from Full Stop (PSTP = 0) The MCU requires an external interrupt or an external reset in order to wake-up from stop-mode. If the MCU gets an external reset during full stop mode active, the CRG asynchronously restores all configuration bits in the register space to its default settings and will perform a maximum of 50 clock check_windows (see Section 2.4.1.4, "Clock Quality Checker"). After completing the clock quality check the CRG starts the reset generator. After completing the reset sequence processing begins by fetching the normal reset vector. Full stop-mode is left and the MCU is in run mode again. If the MCU is woken-up by an interrupt and the fast wake-up feature is disabled (FSTWKP = 0 or SCME = 0), the CRG will also perform a maximum of 50 clock check_windows (see Section 2.4.1.4, "Clock Quality Checker"). If the clock quality check is successful, the CRG will release all system and core clocks and will continue with normal operation. If all clock checks within the Timeout-Window are failing, the CRG will switch to self-clock mode or generate a clock monitor reset (CMRESET) depending on the setting of the SCME bit. If the MCU is woken-up by an interrupt and the fast wake-up feature is enabled (FSTWKP = 1 and SCME = 1), the system will immediately resume operation in self-clock mode (see Section 2.4.1.4, "Clock Quality Checker"). The SCMIF flag will not be set. The system will remain in self-clock mode with oscillator disabled until FSTWKP bit is cleared. The clearing of FSTWKP will start the oscillator and the clock quality check. If the clock quality check is successful, the CRG will switch all system clocks to oscillator clock. The SCMIF flag will be set. See application examples in Figure 2-23 and Figure 2-24. Because the PLL has been powered-down during stop-mode the PLLSEL bit is cleared and the MCU runs on OSCCLK after leaving stop-mode. The software must manually set the PLLSEL bit again, in order to switch system and core clocks to the PLLCLK. NOTE In full stop mode or self-clock mode caused by the fast wake-up feature, the clock monitor and the oscillator are disabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 111 Chapter 2 Clocks and Reset Generator (S12CRGV6) CPU resumes program execution immediately Instruction FSTWKP=1 SCME=1 STOP IRQ Service STOP IRQ Service IRQ Service STOP Interrupt Interrupt Interrupt Power Saving Oscillator Clock Oscillator Disabled PLL Clock Core Clock Self-Clock Mode Figure 2-23. Fast Wake-up from Full Stop Mode: Example 1 . CPU resumes program execution immediately Instruction FSTWKP=1 SCME=1 STOP IRQ Service FSTWKP=0 SCMIE=1 Freq. Uncritical Instructions IRQ Interrupt Freq. Critical Instr. Possible SCM Interrupt Clock Quality Check Oscillator Clock Oscillator Disabled OSC Startup PLL Clock Core Clock Self-Clock Mode Figure 2-24. Fast Wake-up from Full Stop Mode: Example 2 MC9S12XDP512 Data Sheet, Rev. 2.21 112 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.5 Resets This section describes how to reset the CRG, and how the CRG itself controls the reset of the MCU. It explains all special reset requirements. Since the reset generator for the MCU is part of the CRG, this section also describes all automatic actions that occur during or as a result of individual reset conditions. The reset values of registers and signals are provided in Section 2.3, "Memory Map and Register Definition". All reset sources are listed in Table 2-14. Refer to MCU specification for related vector addresses and priorities. Table 2-14. Reset Summary 2.5.1 Reset Source Local Enable Power on Reset None Low Voltage Reset None External Reset None Illegal Address Reset None Clock Monitor Reset PLLCTL (CME = 1, SCME = 0) COP Watchdog Reset COPCTL (CR[2:0] nonzero) Description of Reset Operation The reset sequence is initiated by any of the following events: * Low level is detected at the RESET pin (external reset) * Power on is detected * Low voltage is detected * Illegal Address Reset is detected (see S12XMMC Block Guide for details) * COP watchdog times out * Clock monitor failure is detected and self-clock mode was disabled (SCME=0) Upon detection of any reset event, an internal circuit drives the RESET pin low for 128 SYSCLK cycles (see Figure 2-25). Since entry into reset is asynchronous, it does not require a running SYSCLK. However, the internal reset circuit of the CRG cannot sequence out of current reset condition without a running SYSCLK. The number of 128 SYSCLK cycles might be increased by n = 3 to 6 additional SYSCLK cycles depending on the internal synchronization latency. After 128 + n SYSCLK cycles the RESET pin is released. The reset generator of the CRG waits for additional 64 SYSCLK cycles and then samples the RESET pin to determine the originating source. Table 2-15 shows which vector will be fetched. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 113 Chapter 2 Clocks and Reset Generator (S12CRGV6) Table 2-15. Reset Vector Selection Sampled RESET Pin (64 cycles after release) Clock Monitor Reset Pending COP Reset Pending Vector Fetch 1 0 0 POR / LVR / Illegal Address Reset / External Reset 1 1 X Clock Monitor Reset 1 0 1 COP Reset 0 X X POR / LVR / Illegal Address Reset / External Reset with rise of RESET pin NOTE External circuitry connected to the RESET pin should not include a large capacitance that would interfere with the ability of this signal to rise to a valid logic 1 within 64 SYSCLK cycles after the low drive is released. The internal reset of the MCU remains asserted while the reset generator completes the 192 SYSCLK long reset sequence. The reset generator circuitry always makes sure the internal reset is deasserted synchronously after completion of the 192 SYSCLK cycles. In case the RESET pin is externally driven low for more than these 192 SYSCLK cycles (external reset), the internal reset remains asserted too. RESET )( )( CRG drives RESET pin low RESET pin released ) ) SYSCLK ( ( 128 + n cycles Possibly SYSCLK not running ) ( 64 cycles With n being min 3 / max 6 cycles depending on internal synchronization delay Possibly RESET driven low externally Figure 2-25. RESET Timing MC9S12XDP512 Data Sheet, Rev. 2.21 114 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.5.2 Clock Monitor Reset The CRG generates a clock monitor reset in case all of the following conditions are true: * Clock monitor is enabled (CME = 1) * Loss of clock is detected * Self-clock mode is disabled (SCME = 0). The reset event asynchronously forces the configuration registers to their default settings (see Section 2.3, "Memory Map and Register Definition"). In detail the CME and the SCME are reset to logical `1' (which doesn't change the state of the CME bit, because it has already been set). As a consequence the CRG immediately enters self clock mode and starts its internal reset sequence. In parallel the clock quality check starts. As soon as clock quality check indicates a valid oscillator clock the CRG switches to OSCCLK and leaves self clock mode. Since the clock quality checker is running in parallel to the reset generator, the CRG may leave self clock mode while still completing the internal reset sequence. When the reset sequence is finished, the CRG checks the internally latched state of the clock monitor fail circuit. If a clock monitor fail is indicated, processing begins by fetching the clock monitor reset vector. 2.5.3 Computer Operating Properly Watchdog (COP) Reset When COP is enabled, the CRG expects sequential write of 0x_55 and 0x_AA (in this order) to the ARMCOP register during the selected time-out period. Once this is done, the COP time-out period restarts. If the program fails to do this the CRG will generate a reset. Also, if any value other than 0x_55 or 0x_AA is written, the CRG immediately generates a reset. In case windowed COP operation is enabled writes (0x_55 or 0x_AA) to the ARMCOP register must occur in the last 25% of the selected time-out period. A premature write the CRG will immediately generate a reset. As soon as the reset sequence is completed the reset generator checks the reset condition. If no clock monitor failure is indicated and the latched state of the COP timeout is true, processing begins by fetching the COP vector. 2.5.4 Power On Reset, Low Voltage Reset The on-chip voltage regulator detects when VDD to the MCU has reached a certain level and asserts power on reset or low voltage reset or both. As soon as a power on reset or low voltage reset is triggered the CRG performs a quality check on the incoming clock signal. As soon as clock quality check indicates a valid oscillator clock signal, the reset sequence starts using the oscillator clock. If after 50 check windows the clock quality check indicated a non-valid oscillator clock, the reset sequence starts using self-clock mode. Figure 2-26 and Figure 2-27 show the power-up sequence for cases when the RESET pin is tied to VDD and when the RESET pin is held low. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 115 Chapter 2 Clocks and Reset Generator (S12CRGV6) Clock Quality Check (no Self-Clock Mode) RESET )( Internal POR )( 128 SYSCLK Internal RESET )( 64 SYSCLK Figure 2-26. RESET Pin Tied to VDD (by a pull-up resistor) Clock Quality Check (no Self Clock Mode) )( RESET Internal POR )( 128 SYSCLK Internal RESET )( 64 SYSCLK Figure 2-27. RESET Pin Held Low Externally 2.6 Interrupts The interrupts/reset vectors requested by the CRG are listed in Table 2-16. Refer to MCU specification for related vector addresses and priorities. Table 2-16. CRG Interrupt Vectors 2.6.1 Interrupt Source CCR Mask Local Enable Real time interrupt I bit CRGINT (RTIE) LOCK interrupt I bit CRGINT (LOCKIE) SCM interrupt I bit CRGINT (SCMIE) Real Time Interrupt The CRG generates a real time interrupt when the selected interrupt time period elapses. RTI interrupts are locally disabled by setting the RTIE bit to 0. The real time interrupt flag (RTIF) is set to1 when a timeout occurs, and is cleared to 0 by writing a 1 to the RTIF bit. The RTI continues to run during pseudo stop mode if the PRE bit is set to 1. This feature can be used for periodic wakeup from pseudo stop if the RTI interrupt is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 116 Freescale Semiconductor Chapter 2 Clocks and Reset Generator (S12CRGV6) 2.6.2 PLL Lock Interrupt The CRG generates a PLL Lock interrupt when the LOCK condition of the PLL has changed, either from a locked state to an unlocked state or vice versa. Lock interrupts are locally disabled by setting the LOCKIE bit to 0. The PLL Lock interrupt flag (LOCKIF) is set to1 when the LOCK condition has changed, and is cleared to 0 by writing a 1 to the LOCKIF bit. 2.6.3 Self Clock Mode Interrupt The CRG generates a self clock mode interrupt when the SCM condition of the system has changed, either entered or exited self clock mode. SCM conditions can only change if the self clock mode enable bit (SCME) is set to 1. SCM conditions are caused by a failing clock quality check after power on reset (POR) or low voltage reset (LVR) or recovery from full stop mode (PSTP = 0) or clock monitor failure. For details on the clock quality check refer to Section 2.4.1.4, "Clock Quality Checker". If the clock monitor is enabled (CME = 1) a loss of external clock will also cause a SCM condition (SCME = 1). SCM interrupts are locally disabled by setting the SCMIE bit to 0. The SCM interrupt flag (SCMIF) is set to1 when the SCM condition has changed, and is cleared to 0 by writing a 1 to the SCMIF bit. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 117 Chapter 2 Clocks and Reset Generator (S12CRGV6) MC9S12XDP512 Data Sheet, Rev. 2.21 118 Freescale Semiconductor Chapter 3 Pierce Oscillator (S12XOSCLCPV1) 3.1 Introduction The Pierce oscillator (XOSC) module provides a robust, low-noise and low-power clock source. The module will be operated from the VDDPLL supply rail (2.5 V nominal) and require the minimum number of external components. It is designed for optimal start-up margin with typical crystal oscillators. 3.1.1 Features The XOSC will contain circuitry to dynamically control current gain in the output amplitude. This ensures a signal with low harmonic distortion, low power and good noise immunity. * High noise immunity due to input hysteresis * Low RF emissions with peak-to-peak swing limited dynamically * Transconductance (gm) sized for optimum start-up margin for typical oscillators * Dynamic gain control eliminates the need for external current limiting resistor * Integrated resistor eliminates the need for external bias resistor * Low power consumption: -- Operates from 2.5 V (nominal) supply -- Amplitude control limits power * Clock monitor 3.1.2 Modes of Operation Two modes of operation exist: 1. Loop controlled Pierce oscillator 2. External square wave mode featuring also full swing Pierce without internal feedback resistor MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 119 Chapter 3 Pierce Oscillator (S12XOSCLCPV1) 3.1.3 Block Diagram Figure 3-1 shows a block diagram of the XOSC. Monitor_Failure Clock Monitor OSCCLK Peak Detector Gain Control VDDPLL = 2.5 V Rf XTAL EXTAL Figure 3-1. XOSC Block Diagram 3.2 External Signal Description This section lists and describes the signals that connect off chip 3.2.1 VDDPLL and VSSPLL -- Operating and Ground Voltage Pins Theses pins provides operating voltage (VDDPLL) and ground (VSSPLL) for the XOSC circuitry. This allows the supply voltage to the XOSC to be independently bypassed. 3.2.2 EXTAL and XTAL -- Input and Output Pins These pins provide the interface for either a crystal or a CMOS compatible clock to control the internal clock generator circuitry. EXTAL is the external clock input or the input to the crystal oscillator amplifier. XTAL is the output of the crystal oscillator amplifier. The MCU internal system clock is derived from the MC9S12XDP512 Data Sheet, Rev. 2.21 120 Freescale Semiconductor Chapter 3 Pierce Oscillator (S12XOSCLCPV1) EXTAL input frequency. In full stop mode (PSTP = 0), the EXTAL pin is pulled down by an internal resistor of typical 200 k. NOTE Freescale recommends an evaluation of the application board and chosen resonator or crystal by the resonator or crystal supplier. Loop controlled circuit is not suited for overtone resonators and crystals. EXTAL C1 MCU Crystal or Ceramic Resonator XTAL C2 VSSPLL Figure 3-2. Loop Controlled Pierce Oscillator Connections (XCLKS = 1) NOTE Full swing Pierce circuit is not suited for overtone resonators and crystals without a careful component selection. EXTAL C1 MCU RB Crystal or Ceramic Resonator RS* XTAL C2 VSSPLL * Rs can be zero (shorted) when use with higher frequency crystals. Refer to manufacturer's data. Figure 3-3. Full Swing Pierce Oscillator Connections (XCLKS = 0) EXTAL CMOS Compatible External Oscillator (VDDPLL Level) MCU XTAL Not Connected Figure 3-4. External Clock Connections (XCLKS = 0) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 121 Chapter 3 Pierce Oscillator (S12XOSCLCPV1) 3.2.3 XCLKS -- Input Signal The XCLKS is an input signal which controls whether a crystal in combination with the internal loop controlled (low power) Pierce oscillator is used or whether full swing Pierce oscillator/external clock circuitry is used. Refer to the Device Overview chapter for polarity and sampling conditions of the XCLKS pin. Table 3-1 lists the state coding of the sampled XCLKS signal. . Table 3-1. Clock Selection Based on XCLKS XCLKS 3.3 Description 1 Loop controlled Pierce oscillator selected 0 Full swing Pierce oscillator/external clock selected Memory Map and Register Definition The CRG contains the registers and associated bits for controlling and monitoring the oscillator module. 3.4 Functional Description The XOSC module has control circuitry to maintain the crystal oscillator circuit voltage level to an optimal level which is determined by the amount of hysteresis being used and the maximum oscillation range. The oscillator block has two external pins, EXTAL and XTAL. The oscillator input pin, EXTAL, is intended to be connected to either a crystal or an external clock source. The selection of loop controlled Pierce oscillator or full swing Pierce oscillator/external clock depends on the XCLKS signal which is sampled during reset. The XTAL pin is an output signal that provides crystal circuit feedback. A buffered EXTAL signal becomes the internal clock. To improve noise immunity, the oscillator is powered by the VDDPLL and VSSPLL power supply pins. 3.4.1 Gain Control A closed loop control system will be utilized whereby the amplifier is modulated to keep the output waveform sinusoidal and to limit the oscillation amplitude. The output peak to peak voltage will be kept above twice the maximum hysteresis level of the input buffer. Electrical specification details are provided in the Electrical Characteristics appendix. 3.4.2 Clock Monitor The clock monitor circuit is based on an internal RC time delay so that it can operate without any MCU clocks. If no OSCCLK edges are detected within this RC time delay, the clock monitor indicates failure which asserts self-clock mode or generates a system reset depending on the state of SCME bit. If the clock monitor is disabled or the presence of clocks is detected no failure is indicated.The clock monitor function is enabled/disabled by the CME control bit, described in the CRG block description chapter. MC9S12XDP512 Data Sheet, Rev. 2.21 122 Freescale Semiconductor Chapter 3 Pierce Oscillator (S12XOSCLCPV1) 3.4.3 Wait Mode Operation During wait mode, XOSC is not impacted. 3.4.4 Stop Mode Operation XOSC is placed in a static state when the part is in stop mode except when pseudo-stop mode is enabled. During pseudo-stop mode, XOSC is not impacted. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 123 Chapter 3 Pierce Oscillator (S12XOSCLCPV1) MC9S12XDP512 Data Sheet, Rev. 2.21 124 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.1 Introduction The ATD10B16C is a 16-channel, 10-bit, multiplexed input successive approximation analog-to-digital converter. Refer to the Electrical Specifications chapter for ATD accuracy. 4.1.1 * * * * * * * * * * * * * * 4.1.2 Features 8-/10-bit resolution 7 s, 10-bit single conversion time Sample buffer amplifier Programmable sample time Left/right justified, signed/unsigned result data External trigger control Conversion completion interrupt generation Analog input multiplexer for 16 analog input channels Analog/digital input pin multiplexing 1 to 16 conversion sequence lengths Continuous conversion mode Multiple channel scans Configurable external trigger functionality on any AD channel or any of four additional trigger inputs. The four additional trigger inputs can be chip external or internal. Refer to device specification for availability and connectivity Configurable location for channel wrap around (when converting multiple channels in a sequence) Modes of Operation There is software programmable selection between performing single or continuous conversion on a single channel or multiple channels. 4.1.3 Block Diagram Refer to Figure 4-1 for a block diagram of the ATD0B16C block. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 125 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Bus Clock ATD clock Clock Prescaler Trigger Mux ETRIG0 ETRIG1 ETRIG2 ATD10B16C Sequence Complete Mode and Timing Control Interrupt ETRIG3 (see Device Overview chapter for availability and connectivity) ATDCTL1 ATDDIEN Results ATD 0 ATD 1 ATD 2 ATD 3 ATD 4 ATD 5 ATD 6 ATD 7 ATD 8 ATD 9 ATD 10 ATD 11 ATD 12 ATD 13 ATD 14 ATD 15 PORTAD VDDA VSSA Successive Approximation Register (SAR) and DAC VRH VRL AN15 AN14 AN13 AN12 AN11 + AN10 Sample & Hold AN9 1 1 AN8 AN7 Analog MUX Comparator AN6 AN5 AN4 AN3 AN2 AN1 AN0 Figure 4-1. ATD10B16C Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 126 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.2 External Signal Description This section lists all inputs to the ATD10B16C block. 4.2.1 ANx (x = 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4, 3, 2, 1, 0) -- Analog Input Channel x Pins This pin serves as the analog input channel x. It can also be configured as general-purpose digital input and/or external trigger for the ATD conversion. 4.2.2 ETRIG3, ETRIG2, ETRIG1, ETRIG0 -- External Trigger Pins These inputs can be configured to serve as an external trigger for the ATD conversion. Refer to the Device Overview chapter for availability and connectivity of these inputs. 4.2.3 VRH, VRL -- High Reference Voltage Pin, Low Reference Voltage Pin VRH is the high reference voltage, VRL is the low reference voltage for ATD conversion. 4.2.4 VDDA, VSSA -- Analog Circuitry Power Supply Pins These pins are the power supplies for the analog circuitry of the ATD10B16CV4 block. 4.3 Memory Map and Register Definition This section provides a detailed description of all registers accessible in the ATD10B16C. 4.3.1 Module Memory Map Table 4-1 gives an overview of all ATD10B16C registers MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 127 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description . Table 4-1. ATD10B16CV4 Memory Map 1 Address Offset Use Access 0x0000 ATD Control Register 0 (ATDCTL0) R/W 0x0001 ATD Control Register 1 (ATDCTL1) R/W 0x0002 ATD Control Register 2 (ATDCTL2) R/W 0x0003 ATD Control Register 3 (ATDCTL3) R/W 0x0004 ATD Control Register 4 (ATDCTL4) R/W 0x0005 ATD Control Register 5 (ATDCTL5) R/W R/W 0x0006 ATD Status Register 0 (ATDSTAT0) 0x0007 Unimplemented 0x0008 ATD Test Register 0 (ATDTEST0)1 R 0x0009 ATD Test Register 1 (ATDTEST1) R/W 0x000A ATD Status Register 2 (ATDSTAT2) R 0x000B ATD Status Register 1 (ATDSTAT1) R 0x000C ATD Input Enable Register 0 (ATDDIEN0) R/W 0x000D ATD Input Enable Register 1 (ATDDIEN1) R/W 0x000E Port Data Register 0 (PORTAD0) R 0x000F Port Data Register 1 (PORTAD1) R 0x0010, 0x0011 ATD Result Register 0 (ATDDR0H, ATDDR0L) R/W 0x0012, 0x0013 ATD Result Register 1 (ATDDR1H, ATDDR1L) R/W 0x0014, 0x0015 ATD Result Register 2 (ATDDR2H, ATDDR2L) R/W 0x0016, 0x0017 ATD Result Register 3 (ATDDR3H, ATDDR3L) R/W 0x0018, 0x0019 ATD Result Register 4 (ATDDR4H, ATDDR4L) R/W 0x001A, 0x001B ATD Result Register 5 (ATDDR5H, ATDDR5L) R/W 0x001C, 0x001D ATD Result Register 6 (ATDDR6H, ATDDR6L) R/W 0x001E, 0x001F ATD Result Register 7 (ATDDR7H, ATDDR7L) R/W 0x0020, 0x0021 ATD Result Register 8 (ATDDR8H, ATDDR8L) R/W 0x0022, 0x0023 ATD Result Register 9 (ATDDR9H, ATDDR9L) R/W 0x0024, 0x0025 ATD Result Register 10 (ATDDR10H, ATDDR10L) R/W 0x0026, 0x0027 ATD Result Register 11 (ATDDR11H, ATDDR11L) R/W 0x0028, 0x0029 ATD Result Register 12 (ATDDR12H, ATDDR12L) R/W 0x002A, 0x002B ATD Result Register 13 (ATDDR13H, ATDDR13L) R/W 0x002C, 0x002D ATD Result Register 14 (ATDDR14H, ATDDR14L) R/W 0x002E, 0x002F ATD Result Register 15 (ATDDR15H, ATDDR15L) R/W ATDTEST0 is intended for factory test purposes only. NOTE Register Address = Base Address + Address Offset, where the Base Address is defined at the MCU level and the Address Offset is defined at the module level. MC9S12XDP512 Data Sheet, Rev. 2.21 128 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2 Register Descriptions This section describes in address order all the ATD10B16C registers and their individual bits. Register Name 0x0000 ATDCTL0 0x0001 ATDCTL1 R R W W 0x0003 ATDCTL3 W R R W W 0x0006 ATDSTAT0 W 0x0008 ATDTEST0 R R 0 0 0 0 0 0 0 AFFC AWAI ETRIGLE ETRIGP ETRIGE ASCIE S8C S4C S2C S1C FIFO FRZ1 FRZ0 SRES8 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0 DJM DSGN SCAN MULT CD CC CB CA ETORF FIFOR CC3 CC2 CC1 CC0 ADPU 0 SCF 0 3 2 1 Bit 0 WRAP3 WRAP2 WRAP1 WRAP0 ETRIGCH3 ETRIGCH2 ETRIGCH1 ETRIGCH0 ASCIF W R Unimplemented W W 0x000A ATDSTAT2 W 0x000C ATDDIEN0 4 R 0x0009 ATDTEST1 0x000B ATDSTAT1 5 ETRIGSEL R 0x0005 ATDCTL5 0x0007 Unimplemented 6 W 0x0002 ATDCTL2 0x0004 ATDCTL4 Bit 7 R R R Unimplemented SC CCF15 CCF14 CCF13 CCF12 CCF11 CCF10 CCF9 CCF8 CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0 IEN15 IEN14 IEN13 IEN12 IEN11 IEN10 IEN9 IEN8 W R W = Unimplemented or Reserved u = Unaffected Figure 4-2. ATD Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 129 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Register Name 0x000D ATDDIEN1 R W 0x000E PORTAD0 W R 0x000F PORTAD1 R Bit 7 6 5 4 3 2 1 Bit 0 IEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0 PTAD15 PTAD14 PTAD13 PTAD12 PTAD11 PTAD10 PTAD9 PTAD8 PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 BIT 0 u 0 0 0 0 0 0 0 0 0 0 0 0 W R BIT 9 MSB BIT 7 MSB 0x0010-0x002F W ATDDRxH- ATDDRxL R BIT 1 u W = Unimplemented or Reserved u = Unaffected Figure 4-2. ATD Register Summary (continued) 4.3.2.1 ATD Control Register 0 (ATDCTL0) Writes to this register will abort current conversion sequence but will not start a new sequence. R 7 6 5 4 0 0 0 0 3 2 1 0 WRAP3 WRAP2 WRAP1 WRAP0 1 1 1 1 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 4-3. ATD Control Register 0 (ATDCTL0) Read: Anytime Write: Anytime Table 4-2. ATDCTL0 Field Descriptions Field 3:0 WRAP[3:0] Description Wrap Around Channel Select Bits -- These bits determine the channel for wrap around when doing multi-channel conversions. The coding is summarized in Table 4-3. MC9S12XDP512 Data Sheet, Rev. 2.21 130 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-3. Multi-Channel Wrap Around Coding 4.3.2.2 WRAP3 WRAP2 WRAP1 WRAP0 Multiple Channel Conversions (MULT = 1) Wrap Around to AN0 after Converting 0 0 0 0 Reserved 0 0 0 1 AN1 0 0 1 0 AN2 0 0 1 1 AN3 0 1 0 0 AN4 0 1 0 1 AN5 0 1 1 0 AN6 0 1 1 1 AN7 1 0 0 0 AN8 1 0 0 1 AN9 1 0 1 0 AN10 1 0 1 1 AN11 1 1 0 0 AN12 1 1 0 1 AN13 1 1 1 0 AN14 1 1 1 1 AN15 ATD Control Register 1 (ATDCTL1) Writes to this register will abort current conversion sequence but will not start a new sequence. 7 R 6 5 4 0 0 0 ETRIGSEL 3 2 1 0 ETRIGCH3 ETRIGCH2 ETRIGCH1 ETRIGCH0 1 1 1 1 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 4-4. ATD Control Register 1 (ATDCTL1) Read: Anytime Write: Anytime Table 4-4. ATDCTL1 Field Descriptions Field Description 7 ETRIGSEL External Trigger Source Select -- This bit selects the external trigger source to be either one of the AD channels or one of the ETRIG[3:0] inputs. See device specification for availability and connectivity of ETRIG[3:0] inputs. If ETRIG[3:0] input option is not available, writing a 1 to ETRISEL only sets the bit but has no effect, that means one of the AD channels (selected by ETRIGCH[3:0]) remains the source for external trigger. The coding is summarized in Table 4-5. 3:0 External Trigger Channel Select -- These bits select one of the AD channels or one of the ETRIG[3:0] inputs ETRIGCH[3:0] as source for the external trigger. The coding is summarized in Table 4-5. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 131 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-5. External Trigger Channel Select Coding 1 4.3.2.3 ETRIGSEL ETRIGCH3 ETRIGCH2 ETRIGCH1 ETRIGCH0 External Trigger Source 0 0 0 0 0 AN0 0 0 0 0 1 AN1 0 0 0 1 0 AN2 0 0 0 1 1 AN3 0 0 1 0 0 AN4 0 0 1 0 1 AN5 0 0 1 1 0 AN6 0 0 1 1 1 AN7 0 1 0 0 0 AN8 0 1 0 0 1 AN9 0 1 0 1 0 AN10 0 1 0 1 1 AN11 0 1 1 0 0 AN12 0 1 1 0 1 AN13 0 1 1 1 0 AN14 0 1 1 1 1 AN15 1 0 0 0 0 ETRIG01 1 0 0 0 1 ETRIG11 1 0 0 1 0 ETRIG21 1 0 0 1 1 ETRIG31 1 0 1 X X Reserved 1 1 X X X Reserved Only if ETRIG[3:0] input option is available (see device specification), else ETRISEL is ignored, that means external trigger source remains on one of the AD channels selected by ETRIGCH[3:0] ATD Control Register 2 (ATDCTL2) This register controls power down, interrupt and external trigger. Writes to this register will abort current conversion sequence but will not start a new sequence. MC9S12XDP512 Data Sheet, Rev. 2.21 132 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 7 6 5 4 3 2 1 ADPU AFFC AWAI ETRIGLE ETRIGP ETRIGE ASCIE 0 0 0 0 0 0 0 R 0 ASCIF W Reset 0 = Unimplemented or Reserved Figure 4-5. ATD Control Register 2 (ATDCTL2) Read: Anytime Write: Anytime Table 4-6. ATDCTL2 Field Descriptions Field Description 7 ADPU ATD Power Down -- This bit provides on/off control over the ATD10B16C block allowing reduced MCU power consumption. Because analog electronic is turned off when powered down, the ATD requires a recovery time period after ADPU bit is enabled. 0 Power down ATD 1 Normal ATD functionality 6 AFFC ATD Fast Flag Clear All 0 ATD flag clearing operates normally (read the status register ATDSTAT1 before reading the result register to clear the associate CCF flag). 1 Changes all ATD conversion complete flags to a fast clear sequence. Any access to a result register will cause the associate CCF flag to clear automatically. 5 AWAI ATD Power Down in Wait Mode -- When entering Wait Mode this bit provides on/off control over the ATD10B16C block allowing reduced MCU power. Because analog electronic is turned off when powered down, the ATD requires a recovery time period after exit from Wait mode. 0 ATD continues to run in Wait mode 1 Halt conversion and power down ATD during Wait mode After exiting Wait mode with an interrupt conversion will resume. But due to the recovery time the result of this conversion should be ignored. 4 ETRIGLE External Trigger Level/Edge Control -- This bit controls the sensitivity of the external trigger signal. See Table 4-7 for details. 3 ETRIGP External Trigger Polarity -- This bit controls the polarity of the external trigger signal. See Table 4-7 for details. 2 ETRIGE External Trigger Mode Enable -- This bit enables the external trigger on one of the AD channels or one of the ETRIG[3:0] inputs as described in Table 4-5. If external trigger source is one of the AD channels, the digital input buffer of this channel is enabled. The external trigger allows to synchronize the start of conversion with external events. 0 Disable external trigger 1 Enable external trigger 1 ASCIE ATD Sequence Complete Interrupt Enable 0 ATD Sequence Complete interrupt requests are disabled. 1 ATD Interrupt will be requested whenever ASCIF = 1 is set. 0 ASCIF ATD Sequence Complete Interrupt Flag -- If ASCIE = 1 the ASCIF flag equals the SCF flag (see Section 4.3.2.7, "ATD Status Register 0 (ATDSTAT0)"), else ASCIF reads zero. Writes have no effect. 0 No ATD interrupt occurred 1 ATD sequence complete interrupt pending MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 133 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-7. External Trigger Configurations ETRIGLE ETRIGP External Trigger Sensitivity 0 0 Falling Edge 0 1 Ring Edge 1 0 Low Level 1 1 High Level MC9S12XDP512 Data Sheet, Rev. 2.21 134 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.4 ATD Control Register 3 (ATDCTL3) This register controls the conversion sequence length, FIFO for results registers and behavior in Freeze Mode. Writes to this register will abort current conversion sequence but will not start a new sequence. 7 R 6 5 4 3 2 1 0 S8C S4C S2C S1C FIFO FRZ1 FRZ0 0 1 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 4-6. ATD Control Register 3 (ATDCTL3) Read: Anytime Write: Anytime Table 4-8. ATDCTL3 Field Descriptions Field Description 6 S8C Conversion Sequence Length -- This bit controls the number of conversions per sequence. Table 4-9 shows all combinations. At reset, S4C is set to 1 (sequence length is 4). This is to maintain software continuity to HC12 Family. 5 S4C Conversion Sequence Length -- This bit controls the number of conversions per sequence. Table 4-9 shows all combinations. At reset, S4C is set to 1 (sequence length is 4). This is to maintain software continuity to HC12 Family. 4 S2C Conversion Sequence Length -- This bit controls the number of conversions per sequence. Table 4-9 shows all combinations. At reset, S4C is set to 1 (sequence length is 4). This is to maintain software continuity to HC12 Family. 3 S1C Conversion Sequence Length -- This bit controls the number of conversions per sequence. Table 4-9 shows all combinations. At reset, S4C is set to 1 (sequence length is 4). This is to maintain software continuity to HC12 Family. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 135 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-8. ATDCTL3 Field Descriptions (continued) Field Description 2 FIFO Result Register FIFO Mode --If this bit is zero (non-FIFO mode), the A/D conversion results map into the result registers based on the conversion sequence; the result of the first conversion appears in the first result register, the second result in the second result register, and so on. If this bit is one (FIFO mode) the conversion counter is not reset at the beginning or ending of a conversion sequence; sequential conversion results are placed in consecutive result registers. In a continuously scanning conversion sequence, the result register counter will wrap around when it reaches the end of the result register file. The conversion counter value (CC3-0 in ATDSTAT0) can be used to determine where in the result register file, the current conversion result will be placed. Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the conversion counter even if FIFO=1. So the first result of a new conversion sequence, started by writing to ATDCTL5, will always be place in the first result register (ATDDDR0). Intended usage of FIFO mode is continuos conversion (SCAN=1) or triggered conversion (ETRIG=1). Finally, which result registers hold valid data can be tracked using the conversion complete flags. Fast flag clear mode may or may not be useful in a particular application to track valid data. 0 Conversion results are placed in the corresponding result register up to the selected sequence length. 1 Conversion results are placed in consecutive result registers (wrap around at end). 1:0 FRZ[1:0] Background Debug Freeze Enable -- When debugging an application, it is useful in many cases to have the ATD pause when a breakpoint (Freeze Mode) is encountered. These 2 bits determine how the ATD will respond to a breakpoint as shown in Table 4-10. Leakage onto the storage node and comparator reference capacitors may compromise the accuracy of an immediately frozen conversion depending on the length of the freeze period. Table 4-9. Conversion Sequence Length Coding S8C S4C S2C S1C Number of Conversions per Sequence 0 0 0 0 16 0 0 0 1 1 0 0 1 0 2 0 0 1 1 3 0 1 0 0 4 0 1 0 1 5 0 1 1 0 6 0 1 1 1 7 1 0 0 0 8 1 0 0 1 9 1 0 1 0 10 1 0 1 1 11 1 1 0 0 12 1 1 0 1 13 1 1 1 0 14 1 1 1 1 15 MC9S12XDP512 Data Sheet, Rev. 2.21 136 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-10. ATD Behavior in Freeze Mode (Breakpoint) FRZ1 FRZ0 Behavior in Freeze Mode 0 0 Continue conversion 0 1 Reserved 1 0 Finish current conversion, then freeze 1 1 Freeze Immediately MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 137 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.5 ATD Control Register 4 (ATDCTL4) This register selects the conversion clock frequency, the length of the second phase of the sample time and the resolution of the A/D conversion (i.e., 8-bits or 10-bits). Writes to this register will abort current conversion sequence but will not start a new sequence. 7 6 5 4 3 2 1 0 SRES8 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0 0 0 0 0 0 1 0 1 R W Reset Figure 4-7. ATD Control Register 4 (ATDCTL4) Read: Anytime Write: Anytime Table 4-11. ATDCTL4 Field Descriptions Field Description 7 SRES8 A/D Resolution Select -- This bit selects the resolution of A/D conversion results as either 8 or 10 bits. The A/D converter has an accuracy of 10 bits. However, if low resolution is required, the conversion can be speeded up by selecting 8-bit resolution. 0 10 bit resolution 1 8 bit resolution 6:5 SMP[1:0] Sample Time Select --These two bits select the length of the second phase of the sample time in units of ATD conversion clock cycles. Note that the ATD conversion clock period is itself a function of the prescaler value (bits PRS4-0). The sample time consists of two phases. The first phase is two ATD conversion clock cycles long and transfers the sample quickly (via the buffer amplifier) onto the A/D machine's storage node. The second phase attaches the external analog signal directly to the storage node for final charging and high accuracy. Table 4-12 lists the lengths available for the second sample phase. 4:0 PRS[4:0] ATD Clock Prescaler -- These 5 bits are the binary value prescaler value PRS. The ATD conversion clock frequency is calculated as follows: [ BusClock ] ATDclock = -------------------------------- x 0.5 [ PRS + 1 ] Note: The maximum ATD conversion clock frequency is half the bus clock. The default (after reset) prescaler value is 5 which results in a default ATD conversion clock frequency that is bus clock divided by 12. Table 4-13 illustrates the divide-by operation and the appropriate range of the bus clock. Table 4-12. Sample Time Select SMP1 SMP0 Length of 2nd Phase of Sample Time 0 0 2 A/D conversion clock periods 0 1 4 A/D conversion clock periods 1 0 8 A/D conversion clock periods 1 1 16 A/D conversion clock periods MC9S12XDP512 Data Sheet, Rev. 2.21 138 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-13. Clock Prescaler Values Prescale Value Total Divisor Value Max. Bus Clock1 Min. Bus Clock2 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110 11111 Divide by 2 Divide by 4 Divide by 6 Divide by 8 Divide by 10 Divide by 12 Divide by 14 Divide by 16 Divide by 18 Divide by 20 Divide by 22 Divide by 24 Divide by 26 Divide by 28 Divide by 30 Divide by 32 Divide by 34 Divide by 36 Divide by 38 Divide by 40 Divide by 42 Divide by 44 Divide by 46 Divide by 48 Divide by 50 Divide by 52 Divide by 54 Divide by 56 Divide by 58 Divide by 60 Divide by 62 Divide by 64 4 MHz 8 MHz 12 MHz 16 MHz 20 MHz 24 MHz 28 MHz 32 MHz 36 MHz 40 MHz 44 MHz 48 MHz 52 MHz 56 MHz 60 MHz 64 MHz 68 MHz 72 MHz 76 MHz 80 MHz 84 MHz 88 MHz 92 MHz 96 MHz 100 MHz 104 MHz 108 MHz 112 MHz 116 MHz 120 MHz 124 MHz 128 MHz 1 MHz 2 MHz 3 MHz 4 MHz 5 MHz 6 MHz 7 MHz 8 MHz 9 MHz 10 MHz 11 MHz 12 MHz 13 MHz 14 MHz 15 MHz 16 MHz 17 MHz 18 MHz 19 MHz 20 MHz 21 MHz 22 MHz 23 MHz 24 MHz 25 MHz 26 MHz 27 MHz 28 MHz 29 MHz 30 MHz 31 MHz 32 MHz 1 Maximum ATD conversion clock frequency is 2 MHz. The maximum allowed bus clock frequency is shown in this column. 2 Minimum ATD conversion clock frequency is 500 kHz. The minimum allowed bus clock frequency is shown in this column. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 139 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.6 ATD Control Register 5 (ATDCTL5) This register selects the type of conversion sequence and the analog input channels sampled. Writes to this register will abort current conversion sequence and start a new conversion sequence. If external trigger is enabled (ETRIGE = 1) an initial write to ATDCTL5 is required to allow starting of a conversion sequence which will then occur on each trigger event. Start of conversion means the beginning of the sampling phase. 7 6 5 4 3 2 1 0 DJM DSGN SCAN MULT CD CC CB CA 0 0 0 0 0 0 0 0 R W Reset Figure 4-8. ATD Control Register 5 (ATDCTL5) Read: Anytime Write: Anytime Table 4-14. ATDCTL5 Field Descriptions Field Description 7 DJM Result Register Data Justification -- This bit controls justification of conversion data in the result registers. See Section 4.3.2.16, "ATD Conversion Result Registers (ATDDRx)" for details. 0 Left justified data in the result registers. 1 Right justified data in the result registers. 6 DSGN Result Register Data Signed or Unsigned Representation -- This bit selects between signed and unsigned conversion data representation in the result registers. Signed data is represented as 2's complement. Signed data is not available in right justification. See <st-bold>4.3.2.16 ATD Conversion Result Registers (ATDDRx) for details. 0 Unsigned data representation in the result registers. 1 Signed data representation in the result registers. Table 4-15 summarizes the result data formats available and how they are set up using the control bits. Table 4-16 illustrates the difference between the signed and unsigned, left justified output codes for an input signal range between 0 and 5.12 Volts. 5 SCAN Continuous Conversion Sequence Mode -- This bit selects whether conversion sequences are performed continuously or only once. If external trigger is enabled (ETRIGE=1) setting this bit has no effect, that means each trigger event starts a single conversion sequence. 0 Single conversion sequence 1 Continuous conversion sequences (scan mode) 4 MULT Multi-Channel Sample Mode -- When MULT is 0, the ATD sequence controller samples only from the specified analog input channel for an entire conversion sequence. The analog channel is selected by channel selection code (control bits CD/CC/CB/CA located in ATDCTL5). When MULT is 1, the ATD sequence controller samples across channels. The number of channels sampled is determined by the sequence length value (S8C, S4C, S2C, S1C). The first analog channel examined is determined by channel selection code (CC, CB, CA control bits); subsequent channels sampled in the sequence are determined by incrementing the channel selection code or wrapping around to AN0 (channel 0. 0 Sample only one channel 1 Sample across several channels MC9S12XDP512 Data Sheet, Rev. 2.21 140 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-14. ATDCTL5 Field Descriptions (continued) Field Description 3:0 C[D:A} Analog Input Channel Select Code -- These bits select the analog input channel(s) whose signals are sampled and converted to digital codes. Table 4-17 lists the coding used to select the various analog input channels. In the case of single channel conversions (MULT = 0), this selection code specified the channel to be examined. In the case of multiple channel conversions (MULT = 1), this selection code represents the first channel to be examined in the conversion sequence. Subsequent channels are determined by incrementing the channel selection code or wrapping around to AN0 (after converting the channel defined by the Wrap Around Channel Select Bits WRAP[3:0] in ATDCTL0). In case starting with a channel number higher than the one defined by WRAP[3:0] the first wrap around will be AN15 to AN0. Table 4-15. Available Result Data Formats. SRES8 DJM DSGN Result Data Formats Description and Bus Bit Mapping 1 0 0 8-bit / left justified / unsigned -- bits 15:8 1 0 1 8-bit / left justified / signed -- bits 15:8 1 1 X 8-bit / right justified / unsigned -- bits 7:0 0 0 0 10-bit / left justified / unsigned -- bits 15:6 0 0 1 10-bit / left justified / signed --- bits 15:6 0 1 X 10-bit / right justified / unsigned -- bits 9:0 Table 4-16. Left Justified, Signed and Unsigned ATD Output Codes. Input Signal VRL = 0 Volts VRH = 5.12 Volts Signed 8-Bit Codes Unsigned 8-Bit Codes Signed 10-Bit Codes Unsigned 10-Bit Codes 5.120 Volts 7F FF 7FC0 FFC0 5.100 7F FF 7F00 FF00 5.080 7E FE 7E00 FE00 2.580 01 81 0100 8100 2.560 00 80 0000 8000 2.540 FF 7F FF00 7F00 0.020 81 01 8100 0100 0.000 80 00 8000 0000 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 141 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-17. Analog Input Channel Select Coding CD CC CB CA Analog Input Channel 0 0 0 0 AN0 0 0 0 1 AN1 0 0 1 0 AN2 0 0 1 1 AN3 0 1 0 0 AN4 0 1 0 1 AN5 0 1 1 0 AN6 0 1 1 1 AN7 1 0 0 0 AN8 1 0 0 1 AN9 1 0 1 0 AN10 1 0 1 1 AN11 1 1 0 0 AN12 1 1 0 1 AN13 1 1 1 0 AN14 1 1 1 1 AN15 MC9S12XDP512 Data Sheet, Rev. 2.21 142 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.7 ATD Status Register 0 (ATDSTAT0) This read-only register contains the Sequence Complete Flag, overrun flags for external trigger and FIFO mode, and the conversion counter. 7 6 R 5 4 ETORF FIFOR 0 0 0 SCF 3 2 1 0 CC3 CC2 CC1 CC0 0 0 0 0 W Reset 0 0 = Unimplemented or Reserved Figure 4-9. ATD Status Register 0 (ATDSTAT0) Read: Anytime Write: Anytime (No effect on CC[3:0]) Table 4-18. ATDSTAT0 Field Descriptions Field 7 SCF 5 ETORF Description Sequence Complete Flag -- This flag is set upon completion of a conversion sequence. If conversion sequences are continuously performed (SCAN = 1), the flag is set after each one is completed. This flag is cleared when one of the following occurs: * Write "1" to SCF * Write to ATDCTL5 (a new conversion sequence is started) * If AFFC = 1 and read of a result register 0 Conversion sequence not completed 1 Conversion sequence has completed External Trigger Overrun Flag --While in edge trigger mode (ETRIGLE = 0), if additional active edges are detected while a conversion sequence is in process the overrun flag is set. This flag is cleared when one of the following occurs: * Write "1" to ETORF * Write to ATDCTL0,1,2,3,4 (a conversion sequence is aborted) * Write to ATDCTL5 (a new conversion sequence is started) 0 No External trigger over run error has occurred 1 External trigger over run error has occurred MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 143 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-18. ATDSTAT0 Field Descriptions (continued) Field Description 4 FIFOR FIFO Over Run Flag -- This bit indicates that a result register has been written to before its associated conversion complete flag (CCF) has been cleared. This flag is most useful when using the FIFO mode because the flag potentially indicates that result registers are out of sync with the input channels. However, it is also practical for non-FIFO modes, and indicates that a result register has been over written before it has been read (i.e., the old data has been lost). This flag is cleared when one of the following occurs: * Write "1" to FIFOR * Start a new conversion sequence (write to ATDCTL5 or external trigger) 0 No over run has occurred 1 Overrun condition exists (result register has been written while associated CCFx flag remained set) 3:0 CC[3:0} Conversion Counter -- These 4 read-only bits are the binary value of the conversion counter. The conversion counter points to the result register that will receive the result of the current conversion. For example, CC3 = 0, CC2 = 1, CC1 = 1, CC0 = 0 indicates that the result of the current conversion will be in ATD Result Register 6. If in non-FIFO mode (FIFO = 0) the conversion counter is initialized to zero at the begin and end of the conversion sequence. If in FIFO mode (FIFO = 1) the register counter is not initialized. The conversion counters wraps around when its maximum value is reached. Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the conversion counter even if FIFO=1. MC9S12XDP512 Data Sheet, Rev. 2.21 144 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.8 R Reserved Register 0 (ATDTEST0) 7 6 5 4 3 2 1 0 u u u u u u u u 1 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved u = Unaffected Figure 4-10. Reserved Register 0 (ATDTEST0) Read: Anytime, returns unpredictable values Write: Anytime in special modes, unimplemented in normal modes NOTE Writing to this register when in special modes can alter functionality. 4.3.2.9 ATD Test Register 1 (ATDTEST1) This register contains the SC bit used to enable special channel conversions. R 7 6 5 4 3 2 1 u u u u u u u 0 SC W Reset 0 0 0 0 0 = Unimplemented or Reserved 0 0 0 u = Unaffected Figure 4-11. Reserved Register 1 (ATDTEST1) Read: Anytime, returns unpredictable values for bit 7 and bit 6 Write: Anytime NOTE Writing to this register when in special modes can alter functionality. Table 4-19. ATDTEST1 Field Descriptions Field Description 0 SC Special Channel Conversion Bit -- If this bit is set, then special channel conversion can be selected using CC, CB, and CA of ATDCTL5. Table 4-20 lists the coding. 0 Special channel conversions disabled 1 Special channel conversions enabled MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 145 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description Table 4-20. Special Channel Select Coding SC CD CC CB CA Analog Input Channel 1 0 0 X X Reserved 1 0 1 0 0 VRH 1 0 1 0 1 VRL 1 0 1 1 0 (VRH+VRL) / 2 1 0 1 1 1 Reserved 1 1 X X X Reserved 4.3.2.10 ATD Status Register 2 (ATDSTAT2) This read-only register contains the Conversion Complete Flags CCF15 to CCF8. R 7 6 5 4 3 2 1 0 CCF15 CCF14 CCF13 CCF12 CCF11 CCF10 CCF9 CCF8 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 4-12. ATD Status Register 2 (ATDSTAT2) Read: Anytime Write: Anytime, no effect Table 4-21. ATDSTAT2 Field Descriptions Field Description 7:0 CCF[15:8] Conversion Complete Flag Bits -- A conversion complete flag is set at the end of each conversion in a conversion sequence. The flags are associated with the conversion position in a sequence (and also the result register number). Therefore, CCF8 is set when the ninth conversion in a sequence is complete and the result is available in result register ATDDR8; CCF9 is set when the tenth conversion in a sequence is complete and the result is available in ATDDR9, and so forth. A flag CCFx (x = 15, 14, 13, 12, 11, 10, 9, 8) is cleared when one of the following occurs: * Write to ATDCTL5 (a new conversion sequence is started) * If AFFC = 0 and read of ATDSTAT2 followed by read of result register ATDDRx * If AFFC = 1 and read of result register ATDDRx In case of a concurrent set and clear on CCFx: The clearing by method A) will overwrite the set. The clearing by methods B) or C) will be overwritten by the set. 0 Conversion number x not completed 1 Conversion number x has completed, result ready in ATDDRx MC9S12XDP512 Data Sheet, Rev. 2.21 146 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.11 ATD Status Register 1 (ATDSTAT1) This read-only register contains the Conversion Complete Flags CCF7 to CCF0 R 7 6 5 4 3 2 1 0 CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 4-13. ATD Status Register 1 (ATDSTAT1) Read: Anytime Write: Anytime, no effect Table 4-22. ATDSTAT1 Field Descriptions Field Description 7:0 CCF[7:0] Conversion Complete Flag Bits -- A conversion complete flag is set at the end of each conversion in a conversion sequence. The flags are associated with the conversion position in a sequence (and also the result register number). Therefore, CCF0 is set when the first conversion in a sequence is complete and the result is available in result register ATDDR0; CCF1 is set when the second conversion in a sequence is complete and the result is available in ATDDR1, and so forth. A CCF flag is cleared when one of the following occurs: * Write to ATDCTL5 (a new conversion sequence is started) * If AFFC = 0 and read of ATDSTAT1 followed by read of result register ATDDRx * If AFFC = 1 and read of result register ATDDRx In case of a concurrent set and clear on CCFx: The clearing by method A) will overwrite the set. The clearing by methods B) or C) will be overwritten by the set. Conversion number x not completed Conversion number x has completed, result ready in ATDDRx MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 147 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.12 ATD Input Enable Register 0 (ATDDIEN0) 7 6 5 4 3 2 1 0 IEN15 IEN14 IEN13 IEN12 IEN11 IEN10 IEN9 IEN8 0 0 0 0 0 0 0 0 R W Reset Figure 4-14. ATD Input Enable Register 0 (ATDDIEN0) Read: Anytime Write: anytime Table 4-23. ATDDIEN0 Field Descriptions Field Description 7:0 IEN[15:8] ATD Digital Input Enable on Channel Bits -- This bit controls the digital input buffer from the analog input pin (ANx) to PTADx data register. 0 Disable digital input buffer to PTADx 1 Enable digital input buffer to PTADx. Note: Setting this bit will enable the corresponding digital input buffer continuously. If this bit is set while simultaneously using it as an analog port, there is potentially increased power consumption because the digital input buffer maybe in the linear region. 4.3.2.13 ATD Input Enable Register 1 (ATDDIEN1) 7 6 5 4 3 2 1 0 IEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0 0 0 0 0 0 0 0 0 R W Reset Figure 4-15. ATD Input Enable Register 1 (ATDDIEN1) Read: Anytime Write: Anytime Table 4-24. ATDDIEN1 Field Descriptions Field Description 7:0 IEN[7:0] ATD Digital Input Enable on Channel Bits -- This bit controls the digital input buffer from the analog input pin (ANx) to PTADx data register. 0 Disable digital input buffer to PTADx 1 Enable digital input buffer to PTADx. Note: Setting this bit will enable the corresponding digital input buffer continuously. If this bit is set while simultaneously using it as an analog port, there is potentially increased power consumption because the digital input buffer maybe in the linear region. MC9S12XDP512 Data Sheet, Rev. 2.21 148 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.14 Port Data Register 0 (PORTAD0) The data port associated with the ATD is input-only. The port pins are shared with the analog A/D inputs AN[15:8]. R 7 6 5 4 3 2 1 0 PTAD15 PTAD14 PTAD13 PTAD12 PTAD11 PTAD10 PTAD9 PTAD8 1 1 1 1 1 1 1 1 AN15 AN14 AN13 AN12 AN11 AN10 AN9 AN8 W Reset Pin Function = Unimplemented or Reserved Figure 4-16. Port Data Register 0 (PORTAD0) Read: Anytime Write: Anytime, no effect The A/D input channels may be used for general-purpose digital input. Table 4-25. PORTAD0 Field Descriptions Field Description 7:0 PTAD[15:8] A/D Channel x (ANx) Digital Input Bits-- If the digital input buffer on the ANx pin is enabled (IENx = 1) or channel x is enabled as external trigger (ETRIGE = 1, ETRIGCH[3-0] = x, ETRIGSEL = 0) read returns the logic level on ANx pin (signal potentials not meeting VIL or VIH specifications will have an indeterminate value)). If the digital input buffers are disabled (IENx = 0) and channel x is not enabled as external trigger, read returns a "1". Reset sets all PORTAD0 bits to "1". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 149 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.15 Port Data Register 1 (PORTAD1) The data port associated with the ATD is input-only. The port pins are shared with the analog A/D inputs AN7-0. R 7 6 5 4 3 2 1 0 PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 1 1 1 1 1 1 1 1 AN 7 AN6 AN5 AN4 AN3 AN2 AN1 AN0 W Reset Pin Function = Unimplemented or Reserved Figure 4-17. Port Data Register 1 (PORTAD1) Read: Anytime Write: Anytime, no effect The A/D input channels may be used for general-purpose digital input. Table 4-26. PORTAD1 Field Descriptions Field Description 7:0 PTAD[7:8] A/D Channel x (ANx) Digital Input Bits -- If the digital input buffer on the ANx pin is enabled (IENx=1) or channel x is enabled as external trigger (ETRIGE = 1, ETRIGCH[3-0] = x, ETRIGSEL = 0) read returns the logic level on ANx pin (signal potentials not meeting VIL or VIH specifications will have an indeterminate value)). If the digital input buffers are disabled (IENx = 0) and channel x is not enabled as external trigger, read returns a "1". Reset sets all PORTAD1 bits to "1". MC9S12XDP512 Data Sheet, Rev. 2.21 150 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.16 ATD Conversion Result Registers (ATDDRx) The A/D conversion results are stored in 16 read-only result registers. The result data is formatted in the result registers bases on two criteria. First there is left and right justification; this selection is made using the DJM control bit in ATDCTL5. Second there is signed and unsigned data; this selection is made using the DSGN control bit in ATDCTL5. Signed data is stored in 2's complement format and only exists in left justified format. Signed data selected for right justified format is ignored. Read: Anytime Write: Anytime in special mode, unimplemented in normal modes 4.3.2.16.1 Left Justified Result Data 7 R (10-BIT) BIT 9 MSB R (8-BIT) BIT 7 MSB 6 5 4 3 2 1 0 BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 4-18. Left Justified, ATD Conversion Result Register x, High Byte (ATDDRxH) R (10-BIT) R (8-BIT) 7 6 5 4 3 2 1 0 BIT 1 u BIT 0 u 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved u = Unaffected Figure 4-19. Left Justified, ATD Conversion Result Register x, Low Byte (ATDDRxL) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 151 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.3.2.16.2 R (10-BIT) R (8-BIT) Right Justified Result Data 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 4-20. Right Justified, ATD Conversion Result Register x, High Byte (ATDDRxH) 7 R (10-BIT) BIT 7 R (8-BIT) BIT 7 MSB 6 5 4 3 2 1 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 4-21. Right Justified, ATD Conversion Result Register x, Low Byte (ATDDRxL) 4.4 Functional Description The ATD10B16C is structured in an analog and a digital sub-block. 4.4.1 Analog Sub-block The analog sub-block contains all analog electronics required to perform a single conversion. Separate power supplies VDDA and VSSA allow to isolate noise of other MCU circuitry from the analog sub-block. 4.4.1.1 Sample and Hold Machine The sample and hold (S/H) machine accepts analog signals from the external world and stores them as capacitor charge on a storage node. The sample process uses a two stage approach. During the first stage, the sample amplifier is used to quickly charge the storage node.The second stage connects the input directly to the storage node to complete the sample for high accuracy. When not sampling, the sample and hold machine disables its own clocks. The analog electronics continue drawing their quiescent current. The power down (ADPU) bit must be set to disable both the digital clocks and the analog power consumption. The input analog signals are unipolar and must fall within the potential range of VSSA to VDDA. MC9S12XDP512 Data Sheet, Rev. 2.21 152 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.4.1.2 Analog Input Multiplexer The analog input multiplexer connects one of the 16 external analog input channels to the sample and hold machine. 4.4.1.3 Sample Buffer Amplifier The sample amplifier is used to buffer the input analog signal so that the storage node can be quickly charged to the sample potential. 4.4.1.4 Analog-to-Digital (A/D) Machine The A/D machine performs analog to digital conversions. The resolution is program selectable at either 8 or 10 bits. The A/D machine uses a successive approximation architecture. It functions by comparing the stored analog sample potential with a series of digitally generated analog potentials. By following a binary search algorithm, the A/D machine locates the approximating potential that is nearest to the sampled potential. When not converting the A/D machine disables its own clocks. The analog electronics continue drawing quiescent current. The power down (ADPU) bit must be set to disable both the digital clocks and the analog power consumption. Only analog input signals within the potential range of VRL to VRH (A/D reference potentials) will result in a non-railed digital output codes. 4.4.2 Digital Sub-Block This subsection explains some of the digital features in more detail. See register descriptions for all details. 4.4.2.1 External Trigger Input The external trigger feature allows the user to synchronize ATD conversions to the external environment events rather than relying on software to signal the ATD module when ATD conversions are to take place. The external trigger signal (out of reset ATD channel 15, configurable in ATDCTL1) is programmable to be edge or level sensitive with polarity control. Table 4-27 gives a brief description of the different combinations of control bits and their effect on the external trigger function. Table 4-27. External Trigger Control Bits ETRIGLE ETRIGP ETRIGE SCAN Description X X 0 0 Ignores external trigger. Performs one conversion sequence and stops. X X 0 1 Ignores external trigger. Performs continuous conversion sequences. 0 0 1 X Falling edge triggered. Performs one conversion sequence per trigger. 0 1 1 X Rising edge triggered. Performs one conversion sequence per trigger. 1 0 1 X Trigger active low. Performs continuous conversions while trigger is active. 1 1 1 X Trigger active high. Performs continuous conversions while trigger is active. During a conversion, if additional active edges are detected the overrun error flag ETORF is set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 153 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description In either level or edge triggered modes, the first conversion begins when the trigger is received. In both cases, the maximum latency time is one bus clock cycle plus any skew or delay introduced by the trigger circuitry. After ETRIGE is enabled, conversions cannot be started by a write to ATDCTL5, but rather must be triggered externally. If the level mode is active and the external trigger both de-asserts and re-asserts itself during a conversion sequence, this does not constitute an overrun. Therefore, the flag is not set. If the trigger remains asserted in level mode while a sequence is completing, another sequence will be triggered immediately. 4.4.2.2 General-Purpose Digital Input Port Operation The input channel pins can be multiplexed between analog and digital data. As analog inputs, they are multiplexed and sampled to supply signals to the A/D converter. As digital inputs, they supply external input data that can be accessed through the digital port registers (PORTAD0 & PORTAD1) (input-only). The analog/digital multiplex operation is performed in the input pads. The input pad is always connected to the analog inputs of the ATD10B16C. The input pad signal is buffered to the digital port registers. This buffer can be turned on or off with the ATDDIEN0 & ATDDIEN1 register. This is important so that the buffer does not draw excess current when analog potentials are presented at its input. 4.4.3 Operation in Low Power Modes The ATD10B16C can be configured for lower MCU power consumption in three different ways: * Stop Mode Stop Mode: This halts A/D conversion. Exit from Stop mode will resume A/D conversion, But due to the recovery time the result of this conversion should be ignored. Entering stop mode causes all clocks to halt and thus the system is placed in a minimum power standby mode. This halts any conversion sequence in progress. During recovery from stop mode, there must be a minimum delay for the stop recovery time tSR before initiating a new ATD conversion sequence. * Wait Mode Wait Mode with AWAI = 1: This halts A/D conversion. Exit from Wait mode will resume A/D conversion, but due to the recovery time the result of this conversion should be ignored. Entering wait mode, the ATD conversion either continues or halts for low power depending on the logical value of the AWAIT bit. * Freeze Mode Writing ADPU = 0 (Note that all ATD registers remain accessible.): This aborts any A/D conversion in progress. In freeze mode, the ATD10B16C will behave according to the logical values of the FRZ1 and FRZ0 bits. This is useful for debugging and emulation. NOTE The reset value for the ADPU bit is zero. Therefore, when this module is reset, it is reset into the power down state. MC9S12XDP512 Data Sheet, Rev. 2.21 154 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description 4.5 Resets At reset the ATD10B16C is in a power down state. The reset state of each individual bit is listed within Section 4.3, "Memory Map and Register Definition," which details the registers and their bit fields. 4.6 Interrupts The interrupt requested by the ATD10B16C is listed in Table 4-28. Refer to MCU specification for related vector address and priority. Table 4-28. ATD Interrupt Vectors Interrupt Source Sequence Complete Interrupt CCR Mask Local Enable I bit ASCIE in ATDCTL2 See Section 4.3.2, "Register Descriptions," for further details. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 155 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description MC9S12XDP512 Data Sheet, Rev. 2.21 156 Freescale Semiconductor Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 157 Chapter 4 Analog-to-Digital Converter (ATD10B16CV4) Block Description MC9S12XDP512 Data Sheet, Rev. 2.21 158 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.1 Introduction The ATD10B8C is an 8-channel, 10-bit, multiplexed input successive approximation analog-to-digital converter. Refer to device electrical specifications for ATD accuracy. 5.1.1 * * * * * * * * * * * * * * Features 8/10-bit resolution 7 sec, 10-bit single conversion time Sample buffer amplifier Programmable sample time Left/right justified, signed/unsigned result data External trigger control Conversion completion interrupt generation Analog input multiplexer for 8 analog input channels Analog/digital input pin multiplexing 1-to-8 conversion sequence lengths Continuous conversion mode Multiple channel scans Configurable external trigger functionality on any AD channel or any of four additional external trigger inputs. The four additional trigger inputs can be chip external or internal. Refer to the device overview chapter for availability and connectivity. Configurable location for channel wrap around (when converting multiple channels in a sequence). 5.1.2 5.1.2.1 Modes of Operation Conversion Modes There is software programmable selection between performing single or continuous conversion on a single channel or multiple channels. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 159 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.1.2.2 * * * 5.1.3 MCU Operating Modes Stop mode Entering stop mode causes all clocks to halt and thus the system is placed in a minimum power standby mode. This aborts any conversion sequence in progress. During recovery from stop mode, there must be a minimum delay for the stop recovery time tSR before initiating a new ATD conversion sequence. Wait mode Entering wait mode the ATD conversion either continues or aborts for low power depending on the logical value of the AWAIT bit. Freeze mode In freeze mode the ATD will behave according to the logical values of the FRZ1 and FRZ0 bits. This is useful for debugging and emulation. Block Diagram Figure 5-1 shows a block diagram of the ATD. 5.2 External Signal Description This section lists all inputs to the ATD block. 5.2.1 ANx (x = 7, 6, 5, 4, 3, 2, 1, 0) -- Analog Input Pin This pin serves as the analog input channel x. It can also be configured as general purpose digital port pin and/or external trigger for the ATD conversion. 5.2.2 ETRIG3, ETRIG2, ETRIG1, and ETRIG0 -- External Trigger Pins These inputs can be configured to serve as an external trigger for the ATD conversion. Refer to the device overview chapter for availability and connectivity of these inputs. 5.2.3 VRH and VRL -- High and Low Reference Voltage Pins VRH is the high reference voltage and VRL is the low reference voltage for ATD conversion. 5.2.4 VDDA and VSSA -- Power Supply Pins These pins are the power supplies for the analog circuitry of the ATD block. MC9S12XDP512 Data Sheet, Rev. 2.21 160 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Bus Clock ETRIG0 ETRIG1 ETRIG2 Clock Prescaler ATD clock Trigger Mux ATD10B8C Sequence Complete Mode and Timing Control Interrupt ETRIG3 (See Device Overview chapter for availability and connectivity) ATDDIEN ATDCTL1 PORTAD Results ATD 0 ATD 1 ATD 2 ATD 3 ATD 4 ATD 5 ATD 6 ATD 7 VDDA VSSA Successive Approximation Register (SAR) and DAC VRH VRL AN7 AN6 + AN5 Sample & Hold AN4 1 1 AN3 Analog AN2 - Comparator MUX AN1 AN0 Figure 5-1. ATD Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 161 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3 Memory Map and Register Definition This section provides a detailed description of all registers accessible in the ATD. 5.3.1 Module Memory Map Figure 5-2 gives an overview of all ATD registers. NOTE Register Address = Base Address + Address Offset, where the Base Address is defined at the MCU level and the Address Offset is defined at the module level. 5.3.2 Register Descriptions This section describes in address order all the ATD registers and their individual bits. Register Name Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 WRAP2 WRAP1 WRAP0 0 0 0 0 AFFC AWAI ETRIGLE ETRIGP ETRIGE ASCIE S8C S4C S2C S1C FIFO FRZ1 FRZ0 PRS3 PRS2 PRS1 PRS0 CC CB CA 0 CC2 CC1 CC0 U ATDCTL0 R W ATDCTL1 R ETRIGSEL W ATDCTL2 R W ATDCTL3 R W ATDCTL4 R W SRES8 SMP1 SMP0 PRS4 ATDCTL5 R W DJM DSGN SCAN MULT ATDSTAT0 R W SCF ETORF FIFOR Unimplemente d R W ATDTEST0 R W U U U U U U U ATDTEST1 R W U U 0 0 0 0 0 ADPU 0 0 ETRIGCH2 ETRIGCH1 ETRIGCH0 0 ASCIF SC = Unimplemented or Reserved Figure 5-2. ATD Register Summary (Sheet 1 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 162 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Register Name Unimplemente d R W ATDSTAT1 R W Unimplemente d R W ATDDIEN R W Unimplemente d R W PORTAD R W Bit 7 6 5 4 3 2 1 Bit 0 CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0 IEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0 PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 Left Justified Result Data Note: The read portion of the left justified result data registers has been divided to show the bit position when reading 10-bit and 8-bit conversion data. For more detailed information refer to Section 5.3.2.13, "ATD Conversion Result Registers (ATDDRx)". ATDDR0H 10-BIT BIT 9 MSB BIT 8 BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 8-BIT BIT 7 MSB W ATDDR0L 10-BIT 8-BIT W ATDDR1H BIT 1 U BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 10-BIT BIT 9 MSB 8-BIT BIT 7 MSB W BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 ATDDR1L 10-BIT 8-BIT W BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 ATDDR2H 10-BIT BIT 9 MSB 8-BIT BIT 7 MSB W BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 ATDDR2L 10-BIT 8-BIT W BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 ATDDR3H 10-BIT BIT 9 MSB 8-BIT BIT 7 MSB W BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 BIT 1 U BIT 1 U = Unimplemented or Reserved Figure 5-2. ATD Register Summary (Sheet 2 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 163 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Register Name Bit 7 6 5 4 3 2 1 Bit 0 BIT 1 U BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 ATDDR3L 10-BIT 8-BIT W ATDDR4H 10-BIT BIT 9 MSB 8-BIT BIT 7 MSB W BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 ATDDR4L 10-BIT 8-BIT W BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 ATDD45H 10-BIT BIT 9 MSB 8-BIT BIT 7 MSB W BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 ATDD45L 10-BIT 8-BIT W BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 ATDD46H 10-BIT BIT 9 MSB 8-BIT BIT 7 MSB W BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 ATDDR6L 10-BIT 8-BIT W BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 ATDD47H 10-BIT BIT 9 MSB 8-BIT BIT 7 MSB W BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 ATDD47L 10-BIT 8-BIT W BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 BIT 1 U BIT 1 U BIT 1 U BIT 1 U Right Justified Result Data Note: The read portion of the right justified result data registers has been divided to show the bit position when reading 10-bit and 8-bit conversion data. For more detailed information refer to Section 5.3.2.13, "ATD Conversion Result Registers (ATDDRx)". ATDDR0H 10-BIT 0 0 0 0 0 0 BIT 9 MSB BIT 8 0 0 0 0 0 0 0 0 8-BIT W ATDDR0L 10-BIT BIT 7 8-BIT BIT 7 MSB W BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 = Unimplemented or Reserved Figure 5-2. ATD Register Summary (Sheet 3 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 164 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Register Name Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 ATDDR1H 10-BIT 8-BIT W ATDDR1L 10-BIT BIT 7 8-BIT BIT 7 MSB W ATDDR2H 10-BIT 8-BIT W ATDDR2L 10-BIT BIT 7 8-BIT BIT 7 MSB W ATDDR3H 10-BIT 8-BIT W ATDDR3L 10-BIT BIT 7 8-BIT BIT 7 MSB W ATDDR4H 10-BIT 8-BIT W ATDDR4L 10-BIT BIT 7 8-BIT BIT 7 MSB W ATDD45H 10-BIT 8-BIT W ATDD45L 10-BIT BIT 7 8-BIT BIT 7 MSB W ATDD46H 10-BIT 8-BIT W ATDDR6L 10-BIT BIT 7 8-BIT BIT 7 MSB W 0 0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 5-2. ATD Register Summary (Sheet 4 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 165 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Register Name Bit 7 6 5 4 3 2 1 Bit 0 ATDD47H 10-BIT 8-BIT W 0 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 ATDD47L 10-BIT BIT 7 BIT 7 MSB BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 8-BIT = Unimplemented or Reserved Figure 5-2. ATD Register Summary (Sheet 5 of 5) 5.3.2.1 ATD Control Register 0 (ATDCTL0) Writes to this register will abort current conversion sequence but will not start a new sequence. R 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 W Reset 2 1 0 WRAP2 WRAP1 WRAP0 1 1 1 = Unimplemented or Reserved Figure 5-3. ATD Control Register 0 (ATDCTL0) Read: Anytime Write: Anytime Table 5-1. ATDCTL0 Field Descriptions Field 2-0 WRAP[2:0] Description Wrap Around Channel Select Bits -- These bits determine the channel for wrap around when doing multi-channel conversions. The coding is summarized in Table 5-2. Table 5-2. Multi-Channel Wrap Around Coding WRAP2 WRAP1 WRAP0 Multiple Channel Conversions (MULT = 1) Wrap Around to AN0 after Converting 0 0 0 Reserved 0 0 1 AN1 0 1 0 AN2 0 1 1 AN3 1 0 0 AN4 1 0 1 AN5 1 1 0 AN6 1 1 1 AN7 MC9S12XDP512 Data Sheet, Rev. 2.21 166 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.2 ATD Control Register 1 (ATDCTL1) Writes to this register will abort current conversion sequence but will not start a new sequence. 7 R W ETRIGSEL Reset 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 ETRIGCH2 ETRIGCH1 ETRIGCH0 1 1 1 = Unimplemented or Reserved Figure 5-4. ATD Control Register 1 (ATDCTL1) Read: Anytime Write: Anytime Table 5-3. ATDCTL1 Field Descriptions Field Description 7 ETRIGSEL External Trigger Source Select -- This bit selects the external trigger source to be either one of the AD channels or one of the ETRIG3-0 inputs. See the device overview chapter for availability and connectivity of ETRIG3-0 inputs. If ETRIG3-0 input option is not available, writing a 1 to ETRISEL only sets the bit but has not effect, that means still one of the AD channels (selected by ETRIGCH2-0) is the source for external trigger. The coding is summarized in Table 5-4. 2-0 External Trigger Channel Select -- These bits select one of the AD channels or one of the ETRIG3-0 inputs ETRIGCH[2:0] as source for the external trigger. The coding is summarized in Table 5-4. Table 5-4. External Trigger Channel Select Coding 1 ETRIGSEL ETRIGCH2 ETRIGCH1 ETRIGCH0 External trigger source is 0 0 0 0 AN0 0 0 0 1 AN1 0 0 1 0 AN2 0 0 1 1 AN3 0 1 0 0 AN4 0 1 0 1 AN5 0 1 1 0 AN6 0 1 1 1 AN7 1 0 0 0 ETRIG01 1 0 0 1 ETRIG11 1 0 1 0 ETRIG21 1 0 1 1 ETRIG31 1 1 X X Reserved Only if ETRIG3-0 input option is available (see device overview chapter), else ETRISEL is ignored, that means external trigger source is still on one of the AD channels selected by ETRIGCH2-0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 167 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.3 ATD Control Register 2 (ATDCTL2) This register controls power down, interrupt and external trigger. Writes to this register will abort current conversion sequence but will not start a new sequence. 7 R W Reset ADPU 0 6 5 4 3 2 1 AFFC AWAI ETRIGLE ETRIGP ETRIGE ASCIE 0 0 0 0 0 0 0 ASCIF 0 = Unimplemented or Reserved Figure 5-5. ATD Control Register 2 (ATDCTL2) Read: Anytime Write: Anytime Table 5-5. ATDCTL2 Field Descriptions Field Description 7 ADPU ATD Power Up -- This bit provides on/off control over the ATD block allowing reduced MCU power consumption. Because analog electronic is turned off when powered down, the ATD requires a recovery time period after ADPU bit is enabled. 0 Power down ATD 1 Normal ATD functionality 6 AFFC ATD Fast Flag Clear All 0 ATD flag clearing operates normally (read the status register ATDSTAT1 before reading the result register to clear the associate CCF flag). 1 Changes all ATD conversion complete flags to a fast clear sequence. Any access to a result register will cause the associate CCF flag to clear automatically. 5 AWAI ATD Power Down in Wait Mode -- When entering wait mode this bit provides on/off control over the ATD block allowing reduced MCU power. Because analog electronic is turned off when powered down, the ATD requires a recovery time period after exit from Wait mode. 0 ATD continues to run in Wait mode 1 Halt conversion and power down ATD during wait mode After exiting wait mode with an interrupt conversion will resume. But due to the recovery time the result of this conversion should be ignored. 4 ETRIGLE External Trigger Level/Edge Control -- This bit controls the sensitivity of the external trigger signal. See Table 5-6 for details. 3 ETRIGP External Trigger Polarity -- This bit controls the polarity of the external trigger signal. See Table 5-6 for details. 2 ETRIGE External Trigger Mode Enable -- This bit enables the external trigger on one of the AD channels or one of the ETRIG3-0 inputs as described in Table 5-4. If external trigger source is one of the AD channels, the digital input buffer of this channel is enabled. The external trigger allows to synchronize sample and ATD conversions processes with external events. 0 Disable external trigger 1 Enable external trigger Note: If using one of the AD channel as external trigger (ETRIGSEL = 0) the conversion results for this channel have no meaning while external trigger mode is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 168 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Table 5-5. ATDCTL2 Field Descriptions (continued) Field Description 1 ASCIE ATD Sequence Complete Interrupt Enable 0 ATD Sequence Complete interrupt requests are disabled. 1 ATD Interrupt will be requested whenever ASCIF = 1 is set. 0 ASCIF ATD Sequence Complete Interrupt Flag -- If ASCIE = 1 the ASCIF flag equals the SCF flag (see Section 5.3.2.7, "ATD Status Register 0 (ATDSTAT0)"), else ASCIF reads zero. Writes have no effect. 0 No ATD interrupt occurred 1 ATD sequence complete interrupt pending Table 5-6. External Trigger Configurations 5.3.2.4 ETRIGLE ETRIGP External Trigger Sensitivity 0 0 Falling edge 0 1 Rising edge 1 0 Low level 1 1 High level ATD Control Register 3 (ATDCTL3) This register controls the conversion sequence length, FIFO for results registers and behavior in freeze mode. Writes to this register will abort current conversion sequence but will not start a new sequence. 7 R 0 W Reset 0 6 5 4 3 2 1 0 S8C S4C S2C S1C FIFO FRZ1 FRZ0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 5-6. ATD Control Register 3 (ATDCTL3) Read: Anytime Write: Anytime Table 5-7. ATDCTL3 Field Descriptions Field Description 6-3 S8C, S4C, S2C, S1C Conversion Sequence Length -- These bits control the number of conversions per sequence. Table 5-8 shows all combinations. At reset, S4C is set to 1 (sequence length is 4). This is to maintain software continuity to HC12 Family. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 169 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Table 5-7. ATDCTL3 Field Descriptions (continued) Field Description 2 FIFO Result Register FIFO Mode -- If this bit is zero (non-FIFO mode), the A/D conversion results map into the result registers based on the conversion sequence; the result of the first conversion appears in the first result register, the second result in the second result register, and so on. If this bit is one (FIFO mode) the conversion counter is not reset at the beginning or ending of a conversion sequence; sequential conversion results are placed in consecutive result registers. In a continuously scanning conversion sequence, the result register counter will wrap around when it reaches the end of the result register file. The conversion counter value (CC2-0 in ATDSTAT0) can be used to determine where in the result register file, the current conversion result will be placed. Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the conversion counter even if FIFO=1. So the first result of a new conversion sequence, started by writing to ATDCTL5, will always be place in the first result register (ATDDDR0). Intended usage of FIFO mode is continuos conversion (SCAN=1) or triggered conversion (ETRIG=1). Finally, which result registers hold valid data can be tracked using the conversion complete flags. Fast flag clear mode may or may not be useful in a particular application to track valid data. 0 Conversion results are placed in the corresponding result register up to the selected sequence length. 1 Conversion results are placed in consecutive result registers (wrap around at end). 1-0 FRZ[1:0] Background Debug Freeze Enable -- When debugging an application, it is useful in many cases to have the ATD pause when a breakpoint (Freeze Mode) is encountered. These 2 bits determine how the ATD will respond to a breakpoint as shown in Table 5-9. Leakage onto the storage node and comparator reference capacitors may compromise the accuracy of an immediately frozen conversion depending on the length of the freeze period. Table 5-8. Conversion Sequence Length Coding S8C S4C S2C S1C Number of Conversions per Sequence 0 0 0 0 8 0 0 0 1 1 0 0 1 0 2 0 0 1 1 3 0 1 0 0 4 0 1 0 1 5 0 1 1 0 6 0 1 1 1 7 1 X X X 8 Table 5-9. ATD Behavior in Freeze Mode (Breakpoint) FRZ1 FRZ0 Behavior in Freeze Mode 0 0 Continue conversion 0 1 Reserved 1 0 Finish current conversion, then freeze 1 1 Freeze Immediately MC9S12XDP512 Data Sheet, Rev. 2.21 170 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.5 ATD Control Register 4 (ATDCTL4) This register selects the conversion clock frequency, the length of the second phase of the sample time and the resolution of the A/D conversion (i.e.: 8-bits or 10-bits). Writes to this register will abort current conversion sequence but will not start a new sequence. R W Reset 7 6 5 4 3 2 1 0 SRES8 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0 0 0 0 0 0 1 0 1 Figure 5-7. ATD Control Register 4 (ATDCTL4) Read: Anytime Write: Anytime Table 5-10. ATDCTL4 Field Descriptions Field Description 7 SRES8 A/D Resolution Select -- This bit selects the resolution of A/D conversion results as either 8 or 10 bits. The A/D converter has an accuracy of 10 bits; however, if low resolution is required, the conversion can be speeded up by selecting 8-bit resolution. 0 10-bit resolution 8-bit resolution 6-5 SMP[1:0] Sample Time Select -- These two bits select the length of the second phase of the sample time in units of ATD conversion clock cycles. Note that the ATD conversion clock period is itself a function of the prescaler value (bits PRS4-0). The sample time consists of two phases. The first phase is two ATD conversion clock cycles long and transfers the sample quickly (via the buffer amplifier) onto the A/D machine's storage node. The second phase attaches the external analog signal directly to the storage node for final charging and high accuracy. Table 5-11 lists the lengths available for the second sample phase. 4-0 PRS[4:0] ATD Clock Prescaler -- These 5 bits are the binary value prescaler value PRS. The ATD conversion clock frequency is calculated as follows: [ BusClock ] ATDclock = --------------------------------- x 0.5 [ PRS + 1 ] Note: The maximum ATD conversion clock frequency is half the bus clock. The default (after reset) prescaler value is 5 which results in a default ATD conversion clock frequency that is bus clock divided by 12. Table 5-12 illustrates the divide-by operation and the appropriate range of the bus clock. Table 5-11. Sample Time Select SMP1 SMP0 Length of 2nd Phase of Sample Time 0 0 2 A/D conversion clock periods 0 1 4 A/D conversion clock periods 1 0 8 A/D conversion clock periods 1 1 16 A/D conversion clock periods MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 171 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Table 5-12. Clock Prescaler Values Prescale Value Total Divisor Value Max. Bus Clock1 Min. Bus Clock2 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110 11111 Divide by 2 Divide by 4 Divide by 6 Divide by 8 Divide by 10 Divide by 12 Divide by 14 Divide by 16 Divide by 18 Divide by 20 Divide by 22 Divide by 24 Divide by 26 Divide by 28 Divide by 30 Divide by 32 Divide by 34 Divide by 36 Divide by 38 Divide by 40 Divide by 42 Divide by 44 Divide by 46 Divide by 48 Divide by 50 Divide by 52 Divide by 54 Divide by 56 Divide by 58 Divide by 60 Divide by 62 Divide by 64 4 MHz 8 MHz 12 MHz 16 MHz 20 MHz 24 MHz 28 MHz 32 MHz 36 MHz 40 MHz 44 MHz 48 MHz 52 MHz 56 MHz 60 MHz 64 MHz 68 MHz 72 MHz 76 MHz 80 MHz 84 MHz 88 MHz 92 MHz 96 MHz 100 MHz 104 MHz 108 MHz 112 MHz 116 MHz 120 MHz 124 MHz 128 MHz 1 MHz 2 MHz 3 MHz 4 MHz 5 MHz 6 MHz 7 MHz 8 MHz 9 MHz 10 MHz 11 MHz 12 MHz 13 MHz 14 MHz 15 MHz 16 MHz 17 MHz 18 MHz 19 MHz 20 MHz 21 MHz 22 MHz 23 MHz 24 MHz 25 MHz 26 MHz 27 MHz 28 MHz 29 MHz 30 MHz 31 MHz 32 MHz 1 Maximum ATD conversion clock frequency is 2 MHz. The maximum allowed bus clock frequency is shown in this column. 2 Minimum ATD conversion clock frequency is 500 kHz. The minimum allowed bus clock frequency is shown in this column. MC9S12XDP512 Data Sheet, Rev. 2.21 172 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.6 ATD Control Register 5 (ATDCTL5) This register selects the type of conversion sequence and the analog input channels sampled. Writes to this register will abort current conversion sequence and start a new conversion sequence. 7 R W Reset 6 DJM 0 5 4 DSGN SCAN MULT 0 0 0 3 0 0 2 1 0 CC CB CA 0 0 0 = Unimplemented or Reserved Figure 5-8. ATD Control Register 5 (ATDCTL5) Read: Anytime Write: Anytime Table 5-13. ATDCTL5 Field Descriptions Field Description 7 DJM Result Register Data Justification -- This bit controls justification of conversion data in the result registers. See Section 5.3.2.13, "ATD Conversion Result Registers (ATDDRx)," for details. 0 Left justified data in the result registers 1 Right justified data in the result registers 6 DSGN Result Register Data Signed or Unsigned Representation -- This bit selects between signed and unsigned conversion data representation in the result registers. Signed data is represented as 2's complement. Signed data is not available in right justification. See Section 5.3.2.13, "ATD Conversion Result Registers (ATDDRx)," for details. 0 Unsigned data representation in the result registers 1 Signed data representation in the result registers Table 5-14 summarizes the result data formats available and how they are set up using the control bits. Table 5-15 illustrates the difference between the signed and unsigned, left justified output codes for an input signal range between 0 and 5.12 Volts. 5 SCAN Continuous Conversion Sequence Mode -- This bit selects whether conversion sequences are performed continuously or only once. 0 Single conversion sequence 1 Continuous conversion sequences (scan mode) 4 MULT Multi-Channel Sample Mode -- When MULT is 0, the ATD sequence controller samples only from the specified analog input channel for an entire conversion sequence. The analog channel is selected by channel selection code (control bits CC/CB/CA located in ATDCTL5). When MULT is 1, the ATD sequence controller samples across channels. The number of channels sampled is determined by the sequence length value (S8C, S4C, S2C, S1C). The first analog channel examined is determined by channel selection code (CC, CB, CA control bits); subsequent channels sampled in the sequence are determined by incrementing the channel selection code. 0 Sample only one channel 1 Sample across several channels 2-0 CC, CB, CA Analog Input Channel Select Code -- These bits select the analog input channel(s) whose signals are sampled and converted to digital codes. Table 5-16 lists the coding used to select the various analog input channels. In the case of single channel scans (MULT = 0), this selection code specified the channel examined. In the case of multi-channel scans (MULT = 1), this selection code represents the first channel to be examined in the conversion sequence. Subsequent channels are determined by incrementing channel selection code; selection codes that reach the maximum value wrap around to the minimum value. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 173 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) Table 5-14. Available Result Data Formats SRES8 DJM DSGN Result Data Formats Description and Bus Bit Mapping 1 1 1 0 0 0 0 0 1 0 0 1 0 1 X 0 1 X 8-bit / left justified / unsigned -- bits 8-15 8-bit / left justified / signed -- bits 8-15 8-bit / right justified / unsigned -- bits 0-7 10-bit / left justified / unsigned -- bits 6-15 10-bit / left justified / signed -- bits 6-15 10-bit / right justified / unsigned -- bits 0-9 Table 5-15. Left Justified, Signed, and Unsigned ATD Output Codes Input Signal VRL = 0 Volts VRH = 5.12 Volts Signed 8-Bit Codes Unsigned 8-Bit Codes Signed 10-Bit Codes Unsigned 10-Bit Codes 5.120 Volts 5.100 5.080 7F 7F 7E FF FF FE 7FC0 7F00 7E00 FFC0 FF00 FE00 2.580 2.560 2.540 01 00 FF 81 80 7F 0100 0000 FF00 8100 8000 7F00 0.020 0.000 81 80 01 00 8100 8000 0100 0000 Table 5-16. Analog Input Channel Select Coding CC CB CA Analog Input Channel 0 0 0 AN0 0 0 1 AN1 0 1 0 AN2 0 1 1 AN3 1 0 0 AN4 1 0 1 AN5 1 1 0 AN6 1 1 1 AN7 MC9S12XDP512 Data Sheet, Rev. 2.21 174 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.7 ATD Status Register 0 (ATDSTAT0) This read-only register contains the sequence complete flag, overrun flags for external trigger and FIFO mode, and the conversion counter. 7 R W Reset 6 0 SCF 0 0 5 4 ETORF FIFOR 0 0 3 2 1 0 0 CC2 CC1 CC0 0 0 0 0 = Unimplemented or Reserved Figure 5-9. ATD Status Register 0 (ATDSTAT0) Read: Anytime Write: Anytime (No effect on (CC2, CC1, CC0)) Table 5-17. ATDSTAT0 Field Descriptions Field 7 SCF Description Sequence Complete Flag -- This flag is set upon completion of a conversion sequence. If conversion sequences are continuously performed (SCAN = 1), the flag is set after each one is completed. This flag is cleared when one of the following occurs: A) Write "1" to SCF B) Write to ATDCTL5 (a new conversion sequence is started) C) If AFFC=1 and read of a result register 0 Conversion sequence not completed 1 Conversion sequence has completed 5 ETORF External Trigger Overrun Flag -- While in edge trigger mode (ETRIGLE = 0), if additional active edges are detected while a conversion sequence is in process the overrun flag is set. This flag is cleared when one of the following occurs: A) Write "1" to ETORF B) Write to ATDCTL2, ATDCTL3 or ATDCTL4 (a conversion sequence is aborted) C) Write to ATDCTL5 (a new conversion sequence is started) 0 No External trigger over run error has occurred 1 External trigger over run error has occurred 4 FIFOR FIFO Over Run Flag -- This bit indicates that a result register has been written to before its associated conversion complete flag (CCF) has been cleared. This flag is most useful when using the FIFO mode because the flag potentially indicates that result registers are out of sync with the input channels. However, it is also practical for non-FIFO modes, and indicates that a result register has been over written before it has been read (i.e., the old data has been lost). This flag is cleared when one of the following occurs: A) Write "1" to FIFOR B) Start a new conversion sequence (write to ATDCTL5 or external trigger) 0 No over run has occurred 1 An over run condition exists 2-0 CC[2:0] Conversion Counter -- These 3 read-only bits are the binary value of the conversion counter. The conversion counter points to the result register that will receive the result of the current conversion. E.g. CC2 = 1, CC1 = 1, CC0 = 0 indicates that the result of the current conversion will be in ATD result register 6. If in non-FIFO mode (FIFO = 0) the conversion counter is initialized to zero at the begin and end of the conversion sequence. If in FIFO mode (FIFO = 1) the register counter is not initialized. The conversion counters wraps around when its maximum value is reached. Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the conversion counter even if FIFO=1. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 175 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.8 R Reserved Register (ATDTEST0) 7 6 5 4 3 2 1 0 U U U U U U U U 1 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 5-10. Reserved Register (ATDTEST0) Read: Anytime, returns unpredictable values Write: Anytime in special modes, unimplemented in normal modes NOTE Writing to this register when in special modes can alter functionality. 5.3.2.9 ATD Test Register 1 (ATDTEST1) This register contains the SC bit used to enable special channel conversions. R 7 6 5 4 3 2 1 U U 0 0 0 0 0 0 0 0 0 0 0 0 W Reset SC 0 = Unimplemented or Reserved Figure 5-11. ATD Test Register 1 (ATDTEST1) Read: Anytime, returns unpredictable values for Bit7 and Bit6 Write: Anytime Table 5-18. ATDTEST1 Field Descriptions Field Description 0 SC Special Channel Conversion Bit -- If this bit is set, then special channel conversion can be selected using CC, CB and CA of ATDCTL5. Table 5-19 lists the coding. 0 Special channel conversions disabled 1 Special channel conversions enabled Note: Always write remaining bits of ATDTEST1 (Bit7 to Bit1) zero when writing SC bit. Not doing so might result in unpredictable ATD behavior. Table 5-19. Special Channel Select Coding SC CC CB CA Analog Input Channel 1 0 X X Reserved 1 1 0 0 VRH 1 1 0 1 VRL 1 1 1 0 (VRH+VRL) / 2 1 1 1 1 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 176 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.10 ATD Status Register 1 (ATDSTAT1) This read-only register contains the conversion complete flags. R 7 6 5 4 3 2 1 0 CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 5-12. ATD Status Register 1 (ATDSTAT1) Read: Anytime Write: Anytime, no effect Table 5-20. ATDSTAT1 Field Descriptions Field Description 7-0 CCF[7:0] Conversion Complete Flag x (x = 7, 6, 5, 4, 3, 2, 1, 0) -- A conversion complete flag is set at the end of each conversion in a conversion sequence. The flags are associated with the conversion position in a sequence (and also the result register number). Therefore, CCF0 is set when the first conversion in a sequence is complete and the result is available in result register ATDDR0; CCF1 is set when the second conversion in a sequence is complete and the result is available in ATDDR1, and so forth. A flag CCFx (x = 7, 6, 5, 4, 3, 2,1, 70) is cleared when one of the following occurs: A) Write to ATDCTL5 (a new conversion sequence is started) B) If AFFC=0 and read of ATDSTAT1 followed by read of result register ATDDRx C) If AFFC=1 and read of result register ATDDRx In case of a concurrent set and clear on CCFx: The clearing by method A) will overwrite the set. The clearing by methods B) or C) will be overwritten by the set. 0 Conversion number x not completed 1 Conversion number x has completed, result ready in ATDDRx MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 177 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.11 R W Reset ATD Input Enable Register (ATDDIEN) 7 6 5 4 3 2 1 0 IEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0 0 0 0 0 0 0 0 0 Figure 5-13. ATD Input Enable Register (ATDDIEN) Read: Anytime Write: Anytime Table 5-21. ATDDIEN Field Descriptions Field Description 7-0 IEN[7:0] ATD Digital Input Enable on channel x (x = 7, 6, 5, 4, 3, 2, 1, 0) -- This bit controls the digital input buffer from the analog input pin (ANx) to PTADx data register. 0 Disable digital input buffer to PTADx 1 Enable digital input buffer to PTADx. Note: Setting this bit will enable the corresponding digital input buffer continuously. If this bit is set while simultaneously using it as an analog port, there is potentially increased power consumption because the digital input buffer maybe in the linear region. 5.3.2.12 Port Data Register (PORTAD) The data port associated with the ATD can be configured as general-purpose I/O or input only, as specified in the device overview. The port pins are shared with the analog A/D inputs AN7-0. R 7 6 5 4 3 2 1 0 PTAD7 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 1 1 1 1 1 1 1 1 AN7 AN6 AN5 AN4 AN3 AN2 AN1 AN0 W Reset Pin Function = Unimplemented or Reserved Figure 5-14. Port Data Register (PORTAD) Read: Anytime Write: Anytime, no effect The A/D input channels may be used for general purpose digital input. Table 5-22. PORTAD Field Descriptions Field Description 7-0 PTAD[7:0] A/D Channel x (ANx) Digital Input (x = 7, 6, 5, 4, 3, 2, 1, 0) -- If the digital input buffer on the ANx pin is enabled (IENx = 1) or channel x is enabled as external trigger (ETRIGE = 1,ETRIGCH[2-0] = x,ETRIGSEL = 0) read returns the logic level on ANx pin (signal potentials not meeting VIL or VIH specifications will have an indeterminate value). If the digital input buffers are disabled (IENx = 0) and channel x is not enabled as external trigger, read returns a "1". Reset sets all PORTAD0 bits to "1". MC9S12XDP512 Data Sheet, Rev. 2.21 178 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.3.2.13 ATD Conversion Result Registers (ATDDRx) The A/D conversion results are stored in 8 read-only result registers. The result data is formatted in the result registers based on two criteria. First there is left and right justification; this selection is made using the DJM control bit in ATDCTL5. Second there is signed and unsigned data; this selection is made using the DSGN control bit in ATDCTL5. Signed data is stored in 2's complement format and only exists in left justified format. Signed data selected for right justified format is ignored. Read: Anytime Write: Anytime in special mode, unimplemented in normal modes 5.3.2.13.1 Left Justified Result Data 7 R BIT 9 MSB R BIT 7 MSB 6 5 4 3 2 1 0 BIT 8 BIT 6 BIT 7 BIT 5 BIT 6 BIT 4 BIT 5 BIT 3 BIT 4 BIT 2 BIT 3 BIT 1 BIT 2 BIT 0 0 0 0 0 0 0 0 10-bit data 8-bit data W Reset 0 = Unimplemented or Reserved Figure 5-15. Left Justified, ATD Conversion Result Register, High Byte (ATDDRxH) R R 7 6 5 4 3 2 1 0 BIT 1 U BIT 0 U 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 5-16. Left Justified, ATD Conversion Result Register, Low Byte (ATDDRxL) 5.3.2.13.2 R R Right Justified Result Data 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 BIT 9 MSB 0 BIT 8 0 0 0 0 0 0 0 0 0 10-bit data 8-bit data W Reset = Unimplemented or Reserved Figure 5-17. Right Justified, ATD Conversion Result Register, High Byte (ATDDRxH) 7 R BIT 7 R BIT 7 MSB 6 5 4 3 2 1 0 BIT 6 BIT 6 BIT 5 BIT 5 BIT 4 BIT 4 BIT 3 BIT 3 BIT 2 BIT 2 BIT 1 BIT 1 BIT 0 BIT 0 0 0 0 0 0 0 0 10-bit data 8-bit data W Reset 0 = Unimplemented or Reserved Figure 5-18. Right Justified, ATD Conversion Result Register, Low Byte (ATDDRxL) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 179 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.4 Functional Description The ATD is structured in an analog and a digital sub-block. 5.4.1 Analog Sub-Block The analog sub-block contains all analog electronics required to perform a single conversion. Separate power supplies VDDA and VSSA allow to isolate noise of other MCU circuitry from the analog sub-block. 5.4.1.1 Sample and Hold Machine The sample and hold (S/H) machine accepts analog signals from the external surroundings and stores them as capacitor charge on a storage node. The sample process uses a two stage approach. During the first stage, the sample amplifier is used to quickly charge the storage node.The second stage connects the input directly to the storage node to complete the sample for high accuracy. When not sampling, the sample and hold machine disables its own clocks. The analog electronics still draw their quiescent current. The power down (ADPU) bit must be set to disable both the digital clocks and the analog power consumption. The input analog signals are unipolar and must fall within the potential range of VSSA to VDDA. 5.4.1.2 Analog Input Multiplexer The analog input multiplexer connects one of the 8 external analog input channels to the sample and hold machine. 5.4.1.3 Sample Buffer Amplifier The sample amplifier is used to buffer the input analog signal so that the storage node can be quickly charged to the sample potential. 5.4.1.4 Analog-to-Digital (A/D) Machine The A/D Machine performs analog to digital conversions. The resolution is program selectable at either 8 or 10 bits. The A/D machine uses a successive approximation architecture. It functions by comparing the stored analog sample potential with a series of digitally generated analog potentials. By following a binary search algorithm, the A/D machine locates the approximating potential that is nearest to the sampled potential. When not converting the A/D machine disables its own clocks. The analog electronics still draws quiescent current. The power down (ADPU) bit must be set to disable both the digital clocks and the analog power consumption. Only analog input signals within the potential range of VRL to VRH (A/D reference potentials) will result in a non-railed digital output codes. MC9S12XDP512 Data Sheet, Rev. 2.21 180 Freescale Semiconductor Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.4.2 Digital Sub-Block This subsection explains some of the digital features in more detail. See register descriptions for all details. 5.4.2.1 External Trigger Input The external trigger feature allows the user to synchronize ATD conversions to the external environment events rather than relying on software to signal the ATD module when ATD conversions are to take place. The external trigger signal (out of reset ATD channel 7, configurable in ATDCTL1) is programmable to be edge or level sensitive with polarity control. Table 5-23 gives a brief description of the different combinations of control bits and their effect on the external trigger function. Table 5-23. External Trigger Control Bits ETRIGLE ETRIGP ETRIGE SCAN Description X X 0 0 Ignores external trigger. Performs one conversion sequence and stops. X X 0 1 Ignores external trigger. Performs continuous conversion sequences. 0 0 1 X Falling edge triggered. Performs one conversion sequence per trigger. 0 1 1 X Rising edge triggered. Performs one conversion sequence per trigger. 1 0 1 X Trigger active low. Performs continuous conversions while trigger is active. 1 1 1 X Trigger active high. Performs continuous conversions while trigger is active. During a conversion, if additional active edges are detected the overrun error flag ETORF is set. In either level or edge triggered modes, the first conversion begins when the trigger is received. In both cases, the maximum latency time is one bus clock cycle plus any skew or delay introduced by the trigger circuitry. NOTE The conversion results for the external trigger ATD channel 7 have no meaning while external trigger mode is enabled. Once ETRIGE is enabled, conversions cannot be started by a write to ATDCTL5, but rather must be triggered externally. If the level mode is active and the external trigger both de-asserts and re-asserts itself during a conversion sequence, this does not constitute an overrun; therefore, the flag is not set. If the trigger is left asserted in level mode while a sequence is completing, another sequence will be triggered immediately. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 181 Chapter 5 Analog-to-Digital Converter (S12ATD10B8CV2) 5.4.2.2 General Purpose Digital Input Port Operation The input channel pins can be multiplexed between analog and digital data. As analog inputs, they are multiplexed and sampled to supply signals to the A/D converter. As digital inputs, they supply external input data that can be accessed through the digital port register PORTAD (input-only). The analog/digital multiplex operation is performed in the input pads. The input pad is always connected to the analog inputs of the ATD. The input pad signal is buffered to the digital port registers. This buffer can be turned on or off with the ATDDIEN register. This is important so that the buffer does not draw excess current when analog potentials are presented at its input. 5.4.2.3 Low Power Modes The ATD can be configured for lower MCU power consumption in 3 different ways: 1. Stop mode: This halts A/D conversion. Exit from stop mode will resume A/D conversion, but due to the recovery time the result of this conversion should be ignored. 2. Wait mode with AWAI = 1: This halts A/D conversion. Exit from wait mode will resume A/D conversion, but due to the recovery time the result of this conversion should be ignored. 3. Writing ADPU = 0 (Note that all ATD registers remain accessible.): This aborts any A/D conversion in progress. Note that the reset value for the ADPU bit is zero. Therefore, when this module is reset, it is reset into the power down state. 5.5 Resets At reset the ATD is in a power down state. The reset state of each individual bit is listed within the Register Description section (see Section 5.3, "Memory Map and Register Definition"), which details the registers and their bit-field. 5.6 Interrupts The interrupt requested by the ATD is listed in Table 5-24. Refer to the device overview chapter for related vector address and priority. Table 5-24. ATD Interrupt Vectors Interrupt Source Sequence complete interrupt CCR Mask Local Enable I bit ASCIE in ATDCTL2 See register descriptions for further details. MC9S12XDP512 Data Sheet, Rev. 2.21 182 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.1 Introduction The XGATE module is a peripheral co-processor that allows autonomous data transfers between the MCU's peripherals and the internal memories. It has a built in RISC core that is able to pre-process the transferred data and perform complex communication protocols. The XGATE module is intended to increase the MCU's data throughput by lowering the S12X_CPU's interrupt load. Figure 6-1 gives an overview on the XGATE architecture. This document describes the functionality of the XGATE module, including: * XGATE registers (Section 6.3, "Memory Map and Register Definition") * XGATE RISC core (Section 6.4.1, "XGATE RISC Core") * Hardware semaphores (Section 6.4.4, "Semaphores") * Interrupt handling (Section 6.5, "Interrupts") * Debug features (Section 6.6, "Debug Mode") * Security (Section 6.7, "Security") * Instruction set (Section 6.8, "Instruction Set") 6.1.1 Glossary of Terms XGATE Request A service request from a peripheral module which is directed to the XGATE by the S12X_INT module (see Figure 6-1). XGATE Channel The resources in the XGATE module (i.e. Channel ID number, Priority level, Service Request Vector, Interrupt Flag) which are associated with a particular XGATE Request. XGATE Channel ID A 7-bit identifier associated with an XGATE channel. In S12X designs valid Channel IDs range from $78 to $09. XGATE Channel Interrupt An S12X_CPU interrupt that is triggered by a code sequence running on the XGATE module. XGATE Software Channel MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 183 Chapter 6 XGATE (S12XGATEV2) Special XGATE channel that is not associated with any peripheral service request. A Software Channel is triggered by its Software Trigger Bit which is implemented in the XGATE module. XGATE Semaphore A set of hardware flip-flops that can be exclusively set by either the S12X_CPU or the XGATE. (see 6.4.4/6-204) XGATE Thread A code sequence which is executed by the XGATE's RISC core after receiving an XGATE request. XGATE Debug Mode A special mode in which the XGATE's RISC core is halted for debug purposes. This mode enables the XGATE's debug features (see 6.6/6-206). XGATE Software Error The XGATE is able to detect a number of error conditions caused by erratic software (see 6.4.5/6-205). These error conditions will cause the XGATE to seize program execution and flag an Interrupt to the S12X_CPU. Word A 16 bit entity. Byte An 8 bit entity. 6.1.2 Features The XGATE module includes these features: * Data movement between various targets (i.e Flash, RAM, and peripheral modules) * Data manipulation through built in RISC core * Provides up to 112 XGATE channels -- 104 hardware triggered channels -- 8 software triggered channels * Hardware semaphores which are shared between the S12X_CPU and the XGATE module * Able to trigger S12X_CPU interrupts upon completion of an XGATE transfer * Software error detection to catch erratic application code 6.1.3 Modes of Operation There are four run modes on S12X devices. * Run mode, wait mode, stop mode The XGATE is able to operate in all of these three system modes. Clock activity will be automatically stopped when the XGATE module is idle. * Freeze mode (BDM active) MC9S12XDP512 Data Sheet, Rev. 2.21 184 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) In freeze mode all clocks of the XGATE module may be stopped, depending on the module configuration (see Section 6.3.1.1, "XGATE Control Register (XGMCTL)"). 6.1.4 Block Diagram Figure Figure 6-1 shows a block diagram of the XGATE. Peripheral Interrupts XGATE REQUESTS XGATE XGATE INTERRUPTS S12X_INT Interrupt Flags Semaphores RISC Core Software Triggers Data/Code Software Triggers S12X_DBG S12X_MMC Peripherals Figure 6-1. XGATE Block Diagram 6.2 External Signal Description The XGATE module has no external pins. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 185 Chapter 6 XGATE (S12XGATEV2) 6.3 Memory Map and Register Definition This section provides a detailed description of address space and registers used by the XGATE module. The memory map for the XGATE module is given below in Figure 6-2.The address listed for each register is the sum of a base address and an address offset. The base address is defined at the SoC level and the address offset is defined at the module level. Reserved registers read zero. Write accesses to the reserved registers have no effect. 6.3.1 Register Descriptions This section consists of register descriptions in address order. Each description includes a standard register diagram with an associated figure number. Details of register bit and field function follow the register diagrams, in bit order. Register Name XGMCTL R W 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 0 XGEM XG XG XG XGSSM FRZM DBGM FACTM XGMCHID R XG SWEIFM XGIEM 7 6 5 4 XGE XGFRZ XGDBG XGSS 0 3 XG FACT 2 0 1 0 XG XGIE SWEIF XGCHID[6:0] W Reserved R W Reserved R W Reserved R W XGVBR R XGVBR[15:1] W 0 = Unimplemented or Reserved Figure 6-2. XGATE Register Summary (Sheet 1 of 3) MC9S12XDP512 Data Sheet, Rev. 2.21 186 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) XGIF R 127 126 125 124 123 122 121 0 0 0 0 0 0 0 111 Register Name 113 112 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 XGIF_4F XGIF_4E XGIF_4D XGIF_4C XGIF_4B XGIF_4A XGIF_49 XGIF_48 XGF _47 XGIF_46 XGIF_45 XGIF_44 XGIF_43 XGIF_42 XGIF_41 XGIF_40 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 R W XGIF_3F XGIF_3E XGIF_3D XGIF_3C XGIF_3B XGIF_3A XGIF_39 XGIF_38 XGF _37 XGIF_36 XGIF_35 XGIF_34 XGIF_33 XGIF_32 XGIF_31 XGIF_30 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 R W XGIF_2F XGIF_2E XGIF_2D XGIF_2C XGIF_2B XGIF_2A XGIF_29 XGIF_28 XGF _27 XGIF_26 XGIF_25 XGIF_24 XGIF_23 XGIF_22 XGIF_21 XGIF_20 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 R W XGIF_1F XGIF_1E XGIF_1D XGIF_1C XGIF_1B XGIF_1A XGIF_19 XGIF_18 XGF _17 XGIF_16 XGIF_15 XGIF_14 XGIF_13 XGIF_12 XGIF_11 XGIF_10 15 XGIF 114 R W XGIF 115 XGIF_5F XGIF_5E XGIF_5D XGIF_5C XGIF_5B XGIF_5A XGIF_59 XGIF_58 XGF_57 XGIF_56 XGIF_55 XGIF_54 XGIF_53 XGIF_52 XGIF_51 XGIF_50 79 XGIF 116 R W XGIF 117 XGIF_6F XGIF_6E XGIF_6D XGIF_6C XGIF_6B XGIF_6A XGIF_69 XGIF_68 XGF_67 XGIF_66 XGIF_65 XGIF_64 XGIF_63 XGIF_62 XGIF_61 XGIF_60 95 XGIF 118 R W XGIF 119 XGIF_78 XGF_77 XGIF_76 XGIF_75 XGIF_74 XGIF_73 XGIF_72 XGIF_71 XGIF_70 W XGIF 120 14 13 12 11 10 9 R W 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 XGIF_0F XGIF_0E XGIF_0D XGIF_0C XGIF_0B XGIF_0A XGIF_09 = Unimplemented or Reserved Figure 6-2. XGATE Register Summary (Sheet 2 of 3) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 187 Chapter 6 XGATE (S12XGATEV2) XGSWTM R 15 14 13 0 0 0 W XGSEMM R W Reserved 12 11 10 9 8 0 0 0 0 0 0 0 0 7 6 5 0 0 0 0 3 2 1 0 XGSWT[7:0] XGSWTM[7:0] 0 4 XGSEM[7:0] XGSEMM[7:0] R W XGCCR R 0 0 0 W XGPC R XGN XGZ XGV XGC XGPC W Reserved 0 R W Reserved R W XGR1 R XGR1 W XGR2 R XGR2 W XGR3 R XGR3 W XGR4 R XGR4 W XGR5 R XGR5 W XGR6 R XGR6 W XGR7 R XGR7 W = Unimplemented or Reserved Figure 6-2. XGATE Register Summary (Sheet 3 of 3) MC9S12XDP512 Data Sheet, Rev. 2.21 188 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.3.1.1 XGATE Control Register (XGMCTL) All module level switches and flags are located in the module control register Figure 6-3. 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 0 XG SSM XG FACTM 0 0 R W XGEM Reset 0 XG XG FRZM DBGM 0 0 7 0 0 5 4 3 2 0 XG XGIEM SWEIFM 0 6 XGE XGFRZ XGDBG XGSS XGFACT 0 0 0 0 0 0 1 0 XG SWEIF XGIE 0 0 = Unimplemented or Reserved Figure 6-3. XGATE Control Register (XGMCTL) Read: Anytime Write: Anytime Table 6-1. XGMCTL Field Descriptions (Sheet 1 of 3) Field Description 15 XGEM XGE Mask -- This bit controls the write access to the XGE bit. The XGE bit can only be set or cleared if a "1" is written to the XGEM bit in the same register access. Read: This bit will always read "0". Write: 0 Disable write access to the XGE in the same bus cycle 1 Enable write access to the XGE in the same bus cycle 14 XGFRZM XGFRZ Mask -- This bit controls the write access to the XGFRZ bit. The XGFRZ bit can only be set or cleared if a "1" is written to the XGFRZM bit in the same register access. Read: This bit will always read "0". Write: 0 Disable write access to the XGFRZ in the same bus cycle 1 Enable write access to the XGFRZ in the same bus cycle 13 XGDBGM XGDBG Mask -- This bit controls the write access to the XGDBG bit. The XGDBG bit can only be set or cleared if a "1" is written to the XGDBGM bit in the same register access. Read: This bit will always read "0". Write: 0 Disable write access to the XGDBG in the same bus cycle 1 Enable write access to the XGDBG in the same bus cycle 12 XGSSM XGSS Mask -- This bit controls the write access to the XGSS bit. The XGSS bit can only be set or cleared if a "1" is written to the XGSSM bit in the same register access. Read: This bit will always read "0". Write: 0 Disable write access to the XGSS in the same bus cycle 1 Enable write access to the XGSS in the same bus cycle MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 189 Chapter 6 XGATE (S12XGATEV2) Table 6-1. XGMCTL Field Descriptions (Sheet 2 of 3) Field 11 XGFACTM Description XGFACT Mask -- This bit controls the write access to the XGFACT bit. The XGFACT bit can only be set or cleared if a "1" is written to the XGFACTM bit in the same register access. Read: This bit will always read "0". Write: 0 Disable write access to the XGFACT in the same bus cycle 1 Enable write access to the XGFACT in the same bus cycle XGSWEIF Mask -- This bit controls the write access to the XGSWEIF bit. The XGSWEIF bit can only be cleared 9 XGSWEIFM if a "1" is written to the XGSWEIFM bit in the same register access. Read: This bit will always read "0". Write: 0 Disable write access to the XGSWEIF in the same bus cycle 1 Enable write access to the XGSWEIF in the same bus cycle 8 XGIEM XGIE Mask -- This bit controls the write access to the XGIE bit. The XGIE bit can only be set or cleared if a "1" is written to the XGIEM bit in the same register access. Read: This bit will always read "0". Write: 0 Disable write access to the XGIE in the same bus cycle 1 Enable write access to the XGIE in the same bus cycle 7 XGE XGATE Module Enable -- This bit enables the XGATE module. If the XGATE module is disabled, pending XGATE requests will be ignored. The thread that is executed by the RISC core while the XGE bit is cleared will continue to run. Read: 0 XGATE module is disabled 1 XGATE module is enabled Write: 0 Disable XGATE module 1 Enable XGATE module 6 XGFRZ Halt XGATE in Freeze Mode -- The XGFRZ bit controls the XGATE operation in Freeze Mode (BDM active). Read: 0 RISC core operates normally in Freeze (BDM active) 1 RISC core stops in Freeze Mode (BDM active) Write: 0 Don't stop RISC core in Freeze Mode (BDM active) 1 Stop RISC core in Freeze Mode (BDM active) 5 XGDBG XGATE Debug Mode -- This bit indicates that the XGATE is in Debug Mode (see Section 6.6, "Debug Mode"). Debug Mode can be entered by Software Breakpoints (BRK instruction), Tagged or Forced Breakpoints (see S12X_DBG Section), or by writing a "1" to this bit. Read: 0 RISC core is not in Debug Mode 1 RISC core is in Debug Mode Write: 0 Leave Debug Mode 1 Enter Debug Mode Note: Freeze Mode and Software Error Interrupts have no effect on the XGDBG bit. MC9S12XDP512 Data Sheet, Rev. 2.21 190 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) Table 6-1. XGMCTL Field Descriptions (Sheet 3 of 3) Field Description 4 XGSS XGATE Single Step -- This bit forces the execution of a single instruction if the XGATE is in DEBUG Mode and no software error has occurred (XGSWEIF cleared). Read: 0 No single step in progress 1 Single step in progress Write 0 No effect 1 Execute a single RISC instruction Note: Invoking a Single Step will cause the XGATE to temporarily leave Debug Mode until the instruction has been executed. 3 XGFACT Fake XGATE Activity -- This bit forces the XGATE to flag activity to the MCU even when it is idle. When it is set the MCU will never enter system stop mode which assures that peripheral modules will be clocked during XGATE idle periods Read: 0 XGATE will only flag activity if it is not idle or in debug mode. 1 XGATE will always signal activity to the MCU. Write: 0 Only flag activity if not idle or in debug mode. 1 Always signal XGATE activity. 1 XGSWEIF XGATE Software Error Interrupt Flag -- This bit signals a pending Software Error Interrupt. It is set if the RISC core detects an error condition (see Section 6.4.5, "Software Error Detection"). The RISC core is stopped while this bit is set. Clearing this bit will terminate the current thread and cause the XGATE to become idle. Read: 0 Software Error Interrupt is not pending 1 Software Error Interrupt is pending if XGIE is set Write: 0 No effect 1 Clears the XGSWEIF bit 0 XGIE XGATE Interrupt Enable -- This bit acts as a global interrupt enable for the XGATE module Read: 0 All XGATE interrupts disabled 1 All XGATE interrupts enabled Write: 0 Disable all XGATE interrupts 1 Enable all XGATE interrupts MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 191 Chapter 6 XGATE (S12XGATEV2) 6.3.1.2 XGATE Channel ID Register (XGCHID) The XGATE channel ID register (Figure 6-4) shows the identifier of the XGATE channel that is currently active. This register will read "$00" if the XGATE module is idle. In debug mode this register can be used to start and terminate threads (see Section 6.6.1, "Debug Features"). 7 R 6 5 4 3 0 2 1 0 0 0 0 XGCHID[6:0] W Reset 0 0 0 0 0 = Unimplemented or Reserved Figure 6-4. XGATE Channel ID Register (XGCHID) Read: Anytime Write: In Debug Mode Table 6-2. XGCHID Field Descriptions Field Description 6-0 Request Identifier -- ID of the currently active channel XGCHID[6:0] 6.3.1.3 XGATE Vector Base Address Register (XGVBR) The vector base address register (Figure 6-5 and Figure 6-6) determines the location of the XGATE vector block. 15 14 13 12 11 10 9 R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 XGVBR[15:1] W Reset 8 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 6-5. XGATE Vector Base Address Register (XGVBR) Read: Anytime Write: Only if the module is disabled (XGE = 0) and idle (XGCHID = $00)) Table 6-3. XGVBR Field Descriptions Field Description 15-1 Vector Base Address -- The XGVBR register holds the start address of the vector block in the XGATE XBVBR[15:1] memory map. MC9S12XDP512 Data Sheet, Rev. 2.21 192 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.3.1.4 XGATE Channel Interrupt Flag Vector (XGIF) The interrupt flag vector (Figure 6-6) provides access to the interrupt flags bits of each channel. Each flag may be cleared by writing a "1" to its bit location. R 127 126 125 124 123 122 121 0 0 0 0 0 0 0 120 119 XGIF_78 XGF_77 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 W Reset R W Reset R W Reset R W Reset R W Reset R W Reset R W Reset R W Reset XGIF_6F XGIF_6E XGIF_6D XGIF_6C XGIF_6B XGIF_6A XGIF_69 XGIF_68 XGF_67 118 117 116 115 114 113 112 XGIF_76 XGIF_75 XGIF_74 XGIF_73 XGIF_72 XGIF_71 XGIF_70 XGIF_66 XGIF_65 XGIF_64 XGIF_63 XGIF_62 XGIF_61 XGIF_60 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 XGIF_5F XGIF_5E XGIF_5D XGIF_5C XGIF_5B XGIF_5A XGIF_59 XGIF_58 XGF_57 XGIF_56 XGIF_55 XGIF_54 XGIF_53 XGIF_52 XGIF_51 XGIF_50 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 XGIF_4F XGIF_4E XGIF_4D XGIF_4C XGIF_4B XGIF_4A XGIF_49 XGIF_48 XGF _47 XGIF_46 XGIF_45 XGIF_44 XGIF_43 XGIF_42 XGIF_41 XGIF_40 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 XGIF_3F XGIF_3E XGIF_3D XGIF_3C XGIF_3B XGIF_3A XGIF_39 XGIF_38 XGF _37 XGIF_36 XGIF_35 XGIF_34 XGIF_33 XGIF_32 XGIF_31 XGIF_30 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 XGIF_2F XGIF_2E XGIF_2D XGIF_2C XGIF_2B XGIF_2A XGIF_29 XGIF_28 XGF _27 XGIF_26 XGIF_25 XGIF_24 XGIF_23 XGIF_22 XGIF_21 XGIF_20 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 XGIF_1F XGIF_1E XGIF_1D XGIF_1C XGIF_1B XGIF_1A XGIF_19 XGIF_18 XGF _17 XGIF_16 XGIF_15 XGIF_14 XGIF_13 XGIF_12 XGIF_11 XGIF_10 0 0 0 0 0 0 0 15 14 13 12 11 10 9 XGIF_0F XGIF_0E XGIF_0D XGIF_0C XGIF_0B XGIF_0A XGIF_09 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 6-6. XGATE Channel Interrupt Flag Vector (XGIF) Read: Anytime Write: Anytime MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 193 Chapter 6 XGATE (S12XGATEV2) Table 6-4. XGIV Field Descriptions Field Description 127-9 XGIF[78:9] Channel Interrupt Flags -- These bits signal pending channel interrupts. They can only be set by the RISC core. Each flag can be cleared by writing a "1" to its bit location. Unimplemented interrupt flags will always read "0". Refer to Section "Interrupts" of the SoC Guide for a list of implemented Interrupts. Read: 0 Channel interrupt is not pending 1 Channel interrupt is pending if XGIE is set Write: 0 No effect 1 Clears the interrupt flag NOTE Suggested Mnemonics for accessing the interrupt flag vector on a word basis are: XGIF_7F_70 (XGIF[127:112]), XGIF_6F_60 (XGIF[111:96]), XGIF_5F_50 (XGIF[95:80]), XGIF_4F_40 (XGIF[79:64]), XGIF_3F_30 (XGIF[63:48]), XGIF_2F_20 (XGIF[47:32]), XGIF_1F_10 (XGIF[31:16]), XGIF_0F_00 (XGIF[15:0]) MC9S12XDP512 Data Sheet, Rev. 2.21 194 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.3.1.5 XGATE Software Trigger Register (XGSWT) The eight software triggers of the XGATE module can be set and cleared through the XGATE software trigger register (Figure 6-7). The upper byte of this register, the software trigger mask, controls the write access to the lower byte, the software trigger bits. These bits can be set or cleared if a "1" is written to the associated mask in the same bus cycle. R 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 0 0 0 0 6 5 0 0 0 0 0 4 3 2 1 0 0 0 0 XGSWT[7:0] XGSWTM[7:0] W Reset 7 0 0 0 0 0 Figure 6-7. XGATE Software Trigger Register (XGSWT) Read: Anytime Write: Anytime Table 6-5. XGSWT Field Descriptions Field Description 15-8 Software Trigger Mask -- These bits control the write access to the XGSWT bits. Each XGSWT bit can only XGSWTM[7:0] be written if a "1" is written to the corresponding XGSWTM bit in the same access. Read: These bits will always read "0". Write: 0 Disable write access to the XGSWT in the same bus cycle 1 Enable write access to the corresponding XGSWT bit in the same bus cycle 7-0 XGSWT[7:0] Software Trigger Bits -- These bits act as interrupt flags that are able to trigger XGATE software channels. They can only be set and cleared by software. Read: 0 No software trigger pending 1 Software trigger pending if the XGIE bit is set Write: 0 Clear Software Trigger 1 Set Software Trigger NOTE The XGATE channel IDs that are associated with the eight software triggers are determined on chip integration level. (see Section "Interrupts" of the Soc Guide) XGATE software triggers work like any peripheral interrupt. They can be used as XGATE requests as well as S12X_CPU interrupts. The target of the software trigger must be selected in the S12X_INT module. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 195 Chapter 6 XGATE (S12XGATEV2) 6.3.1.6 XGATE Semaphore Register (XGSEM) The XGATE provides a set of eight hardware semaphores that can be shared between the S12X_CPU and the XGATE RISC core. Each semaphore can either be unlocked, locked by the S12X_CPU or locked by the RISC core. The RISC core is able to lock and unlock a semaphore through its SSEM and CSEM instructions. The S12X_CPU has access to the semaphores through the XGATE semaphore register (Figure 6-8). Refer to section Section 6.4.4, "Semaphores" for details. R 15 14 13 12 11 10 9 8 0 0 0 0 0 0 0 0 0 0 0 W Reset 7 6 5 0 0 0 0 3 2 1 0 0 0 0 XGSEM[7:0] XGSEMM[7:0] 0 4 0 0 0 0 0 Figure 6-8. XGATE Semaphore Register (XGSEM) Read: Anytime Write: Anytime (see Section 6.4.4, "Semaphores") Table 6-6. XGSEM Field Descriptions Field Description 15-8 Semaphore Mask -- These bits control the write access to the XGSEM bits. XGSEMM[7:0] Read: These bits will always read "0". Write: 0 Disable write access to the XGSEM in the same bus cycle 1 Enable write access to the XGSEM in the same bus cycle 7-0 XGSEM[7:0] Semaphore Bits -- These bits indicate whether a semaphore is locked by the S12X_CPU. A semaphore can be attempted to be set by writing a "1" to the XGSEM bit and to the corresponding XGSEMM bit in the same write access. Only unlocked semaphores can be set. A semaphore can be cleared by writing a "0" to the XGSEM bit and a "1" to the corresponding XGSEMM bit in the same write access. Read: 0 Semaphore is unlocked or locked by the RISC core 1 Semaphore is locked by the S12X_CPU Write: 0 Clear semaphore if it was locked by the S12X_CPU 1 Attempt to lock semaphore by the S12X_CPU MC9S12XDP512 Data Sheet, Rev. 2.21 196 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.3.1.7 XGATE Condition Code Register (XGCCR) The XGCCR register (Figure 6-9) provides access to the RISC core's condition code register. R 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 XGN XGZ XGV XGC 0 0 0 0 = Unimplemented or Reserved Figure 6-9. XGATE Condition Code Register (XGCCR) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-7. XGCCR Field Descriptions Field Description 3 XGN Sign Flag -- The RISC core's Sign flag 2 XGZ Zero Flag -- The RISC core's Zero flag 1 XGV Overflow Flag -- The RISC core's Overflow flag 0 XGC Carry Flag -- The RISC core's Carry flag MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 197 Chapter 6 XGATE (S12XGATEV2) 6.3.1.8 XGATE Program Counter Register (XGPC) The XGPC register (Figure 6-10) provides access to the RISC core's program counter. 15 14 13 12 11 10 9 8 R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGPC W Reset 0 0 0 0 0 0 0 0 Figure 6-10. XGATE Program Counter Register (XGPC) Figure 6-11. Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-8. XGPC Field Descriptions Field 15-0 XGPC[15:0] 6.3.1.9 Description Program Counter -- The RISC core's program counter XGATE Register 1 (XGR1) The XGR1 register (Figure 6-12) provides access to the RISC core's register 1. 15 14 13 12 11 10 9 8 R 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGR1 W Reset 7 0 0 0 0 0 0 0 0 Figure 6-12. XGATE Register 1 (XGR1) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-9. XGR1 Field Descriptions Field 15-0 XGR1[15:0] Description XGATE Register 1 -- The RISC core's register 1 MC9S12XDP512 Data Sheet, Rev. 2.21 198 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.3.1.10 XGATE Register 2 (XGR2) The XGR2 register (Figure 6-13) provides access to the RISC core's register 2. 15 14 13 12 11 10 9 8 R 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGR2 W Reset 7 0 0 0 0 0 0 0 0 Figure 6-13. XGATE Register 2 (XGR2) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-10. XGR2 Field Descriptions Field 15-0 XGR2[15:0] 6.3.1.11 Description XGATE Register 2 -- The RISC core's register 2 XGATE Register 3 (XGR3) The XGR3 register (Figure 6-14) provides access to the RISC core's register 3. 15 14 13 12 11 10 9 8 R 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGR3 W Reset 7 0 0 0 0 0 0 0 0 Figure 6-14. XGATE Register 3 (XGR3) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-11. XGR3 Field Descriptions Field 15-0 XGR3[15:0] Description XGATE Register 3 -- The RISC core's register 3 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 199 Chapter 6 XGATE (S12XGATEV2) 6.3.1.12 XGATE Register 4 (XGR4) The XGR4 register (Figure 6-15) provides access to the RISC core's register 4. 15 14 13 12 11 10 9 8 R 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGR4 W Reset 7 0 0 0 0 0 0 0 0 Figure 6-15. XGATE Register 4 (XGR4) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-12. XGR4 Field Descriptions Field 15-0 XGR4[15:0] 6.3.1.13 Description XGATE Register 4 -- The RISC core's register 4 XGATE Register 5 (XGR5) The XGR5 register (Figure 6-16) provides access to the RISC core's register 5. 15 14 13 12 11 10 9 8 R 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGR5 W Reset 7 0 0 0 0 0 0 0 0 Figure 6-16. XGATE Register 5 (XGR5) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-13. XGR5 Field Descriptions Field 15-0 XGR5[15:0] Description XGATE Register 5 -- The RISC core's register 5 MC9S12XDP512 Data Sheet, Rev. 2.21 200 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.3.1.14 XGATE Register 6 (XGR6) The XGR6 register (Figure 6-17) provides access to the RISC core's register 6. 15 14 13 12 11 10 9 8 R 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGR6 W Reset 7 0 0 0 0 0 0 0 0 Figure 6-17. XGATE Register 6 (XGR6) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-14. XGR6 Field Descriptions Field 15-0 XGR6[15:0] 6.3.1.15 Description XGATE Register 6 -- The RISC core's register 6 XGATE Register 7 (XGR7) The XGR7 register (Figure 6-18) provides access to the RISC core's register 7. 15 14 13 12 11 10 9 8 R 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 XGR7 W Reset 7 0 0 0 0 0 0 0 0 Figure 6-18. XGATE Register 7 (XGR7) Read: In debug mode if unsecured Write: In debug mode if unsecured Table 6-15. XGR7 Field Descriptions Field 15-0 XGR7[15:0] Description XGATE Register 7 -- The RISC core's register 7 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 201 Chapter 6 XGATE (S12XGATEV2) 6.4 Functional Description The core of the XGATE module is a RISC processor which is able to access the MCU's internal memories and peripherals (see Figure 6-1). The RISC processor always remains in an idle state until it is triggered by an XGATE request. Then it executes a code sequence that is associated with the request and optionally triggers an interrupt to the S12X_CPU upon completion. Code sequences are not interruptible. A new XGATE request can only be serviced when the previous sequence is finished and the RISC core becomes idle. The XGATE module also provides a set of hardware semaphores which are necessary to ensure data consistency whenever RAM locations or peripherals are shared with the S12X_CPU. The following sections describe the components of the XGATE module in further detail. 6.4.1 XGATE RISC Core The RISC core is a 16 bit processor with an instruction set that is well suited for data transfers, bit manipulations, and simple arithmetic operations (see Section 6.8, "Instruction Set"). It is able to access the MCU's internal memories and peripherals without blocking these resources from the S12X_CPU1. Whenever the S12X_CPU and the RISC core access the same resource, the RISC core will be stalled until the resource becomes available again1. The XGATE offers a high access rate to the MCU's internal RAM. Depending on the bus load, the RISC core can perform up to two RAM accesses per S12X_CPU bus cycle. Bus accesses to peripheral registers or flash are slower. A transfer rate of one bus access per S12X_CPU cycle can not be exceeded. The XGATE module is intended to execute short interrupt service routines that are triggered by peripheral modules or by software. 6.4.2 Programmer's Model Register Block 15 15 R7 R6 15 R5 15 R4 Program Counter 0 PC 0 0 0 0 15 R3 15 R2 15 R1(Variable Pointer) 15 15 0 Condition Code Register NZVC 3 2 1 0 0 0 R0 = 0 0 Figure 6-19. Programmer's Model 1. With the exception of PRR registers (see Section "S12X_MMC"). MC9S12XDP512 Data Sheet, Rev. 2.21 202 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) The programmer's model of the XGATE RISC core is shown in Figure 6-19. The processor offers a set of seven general purpose registers (R1 - R7), which serve as accumulators and index registers. An additional eighth register (R0) is tied to the value "$0000". Register R1 has an additional functionality. It is preloaded with the initial variable pointer of the channel's service request vector (see Figure 6-20). The initial content of the remaining general purpose registers is undefined. The 16 bit program counter allows the addressing of a 64 kbyte address space. The condition code register contains four bits: the sign bit (S), the zero flag (Z), the overflow flag (V), and the carry bit (C). The initial content of the condition code register is undefined. 6.4.3 Memory Map The XGATE's RISC core is able to access an address space of 64K bytes. The allocation of memory blocks within this address space is determined on chip level. Refer to the S12X_MMC Section for a detailed information. The XGATE vector block assigns a start address and a variable pointer to each XGATE channel. Its position in the XGATE memory map can be adjusted through the XGVBR register (see Section 6.3.1.3, "XGATE Vector Base Address Register (XGVBR)"). Figure 6-20 shows the layout of the vector block. Each vector consists of two 16 bit words. The first contains the start address of the service routine. This value will be loaded into the program counter before a service routine is executed. The second word is a pointer to the service routine's variable space. This value will be loaded into register R1 before a service routine is executed. XGVBR +$0000 unused Code +$0024 Channel $09 Initial Program Counter Channel $09 Initial Variable Pointer +$0028 Channel $0A Initial Program Counter Variables Channel $0A Initial Variable Pointer +$002C Channel $0B Initial Program Counter Channel $0B Initial Variable Pointer +$0030 Channel $0C Initial Program Counter Code Channel $0C Initial Variable Pointer +$01E0 Channel $78 Initial Program Counter Variables Channel $78 Initial Variable Pointer Figure 6-20. XGATE Vector Block MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 203 Chapter 6 XGATE (S12XGATEV2) 6.4.4 Semaphores The XGATE module offers a set of eight hardware semaphores. These semaphores provide a mechanism to protect system resources that are shared between two concurrent threads of program execution; one thread running on the S12X_CPU and one running on the XGATE RISC core. Each semaphore can only be in one of the three states: "Unlocked", "Locked by S12X_CPU", and "Locked by XGATE". The S12X_CPU can check and change a semaphore's state through the XGATE semaphore register (XGSEM, see Section 6.3.1.6, "XGATE Semaphore Register (XGSEM)"). The RISC core does this through its SSEM and CSEM instructions. Figure 6-21 illustrates the valid state transitions. %1 XGSEM %0 XGSEM SSEM Instruction LOCKED BY S12X_CPU LOCKED BY XGATE M SE XG EM 0 . GS % EM str X r o GS In X M 1 % E 1 SS % nd a In CS st E ru M ct In SS io st E n ru M ct io n %1 XGSEM SSEM Instruction CSEM Instruction UNLOCKED %0 XGSEM CSEM Instruction Figure 6-21. Semaphore State Transitions MC9S12XDP512 Data Sheet, Rev. 2.21 204 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) Figure 6-22 gives an example of the typical usage of the XGATE hardware semaphores. Two concurrent threads are running on the system. One is running on the S12X_CPU and the other is running on the RISC core. They both have a critical section of code that accesses the same system resource. To guarantee that the system resource is only accessed by one thread at a time, the critical code sequence must be embedded in a semaphore lock/release sequence as shown. S12X_CPU ......... XGATE ......... %1 XGSEMx SSEM XGSEM %1? BCC? critical code sequence critical code sequence XGSEM %0 CSEM ......... ......... Figure 6-22. Algorithm for Locking and Releasing Semaphores 6.4.5 Software Error Detection The XGATE module will immediately terminate program execution after detecting an error condition caused by erratic application code. There are three error conditions: * Execution of an illegal opcode * Illegal vector or opcode fetches * Illegal load or store accesses All opcodes which are not listed in section Section 6.8, "Instruction Set" are illegal opcodes. Illegal vector and opcode fetches as well as illegal load and store accesses are defined on chip level. Refer to the S12X_MMC Section for a detailed information. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 205 Chapter 6 XGATE (S12XGATEV2) 6.5 6.5.1 Interrupts Incoming Interrupt Requests XGATE threads are triggered by interrupt requests which are routed to the XGATE module (see S12X_INT Section). Only a subset of the MCU's interrupt requests can be routed to the XGATE. Which specific interrupt requests these are and which channel ID they are assigned to is documented in Section "Interrupts" of the SoC Guide. 6.5.2 Outgoing Interrupt Requests There are three types of interrupt requests which can be triggered by the XGATE module: 4. Channel interrupts For each XGATE channel there is an associated interrupt flag in the XGATE interrupt flag vector (XGIF, see Section 6.3.1.4, "XGATE Channel Interrupt Flag Vector (XGIF)"). These flags can be set through the "SIF" instruction by the RISC core. They are typically used to flag an interrupt to the S12X_CPU when the XGATE has completed one of its tasks. 5. Software triggers Software triggers are interrupt flags, which can be set and cleared by software (see Section 6.3.1.5, "XGATE Software Trigger Register (XGSWT)"). They are typically used to trigger XGATE tasks by the S12X_CPU software. However these interrupts can also be routed to the S12X_CPU (see S12X_INT Section) and triggered by the XGATE software. 6. Software error interrupt The software error interrupt signals to the S12X_CPU the detection of an error condition in the XGATE application code (see Section 6.4.5, "Software Error Detection"). All XGATE interrupts can be disabled by the XGIE bit in the XGATE module control register (XGMCTL, see Section 6.3.1.1, "XGATE Control Register (XGMCTL)"). 6.6 Debug Mode The XGATE debug mode is a feature to allow debugging of application code. 6.6.1 Debug Features In debug mode the RISC core will be halted and the following debug features will be enabled: * Read and Write accesses to RISC core registers (XGCCR, XGPC, XGR1-XGR7)1 All RISC core registers can be modified. Leaving debug mode will cause the RISC core to continue program execution with the modified register values. 1. Only possible if MCU is unsecured MC9S12XDP512 Data Sheet, Rev. 2.21 206 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) * * 6.6.2 Single Stepping Writing a "1" to the XGSS bit will call the RISC core to execute a single instruction. All RISC core registers will be updated accordingly. Write accesses to the XGCHID register Three operations can be performed by writing to the XGCHID register: - Change of channel ID If a non-zero value is written to the XGCHID while a thread is active (XGCHID $00), then the current channel ID will be changed without any influence on the program counter or the other RISC core registers. - Start of a thread If a non-zero value is written to the XGCHID while the XGATE is idle (XGCHID = $00), then the thread that is associated with the new channel ID will be executed upon leaving debug mode. - Termination of a thread If zero is written to the XGCHID while a thread is active (XGCHID $00), then the current thread will be terminated and the XGATE will become idle. Entering Debug Mode Debug mode can be entered in four ways: 1. Setting XGDBG to "1" Writing a "1" to XGDBG and XGDBGM in the same write access causes the XGATE to enter debug mode upon completion of the current instruction. NOTE After writing to the XGDBG bit the XGATE will not immediately enter debug mode. Depending on the instruction that is executed at this time there may be a delay of several clock cycles. The XGDBG will read "0" until debug mode is entered. 2. Software breakpoints XGATE programs which are stored in the internal RAM allow the use of software breakpoints. A software breakpoint is set by replacing an instruction of the program code with the "BRK" instruction. As soon as the program execution reaches the "BRK" instruction, the XGATE enters debug mode. Additionally a software breakpoint request is sent to the S12X_DBG module (see section 4.9 of the S12X_DBG Section). Upon entering debug mode, the program counter will point to the "BRK" instruction. The other RISC core registers will hold the result of the previous instruction. To resume program execution, the "BRK" instruction must be replaced by the original instruction before leaving debug mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 207 Chapter 6 XGATE (S12XGATEV2) 3. Tagged Breakpoints The S12X_DBG module is able to place tags on fetched opcodes. The XGATE is able to enter debug mode right before a tagged opcode is executed (see section 4.9 of the S12X_DBG Section). Upon entering debug mode, the program counter will point to the tagged instruction. The other RISC core registers will hold the result of the previous instruction. 4. Forced Breakpoints Forced breakpoints are triggered by the S12X_DBG module (see section 4.9 of the S12X_DBG Section). When a forced breakpoint occurs, the XGATE will enter debug mode upon completion of the current instruction. 6.6.3 Leaving Debug Mode Debug mode can only be left by setting the XGDBG bit to "0". If a thread is active (XGCHID has not been cleared in debug mode), program execution will resume at the value of XGPC. 6.7 Security In order to protect XGATE application code on secured S12X devices, a few restrictions in the debug features have been made. These are: * Registers XGCCR, XGPC, and XGR1-XGR7 will read zero on a secured device * Registers XGCCR, XGPC, and XGR1-XGR7 can not be written on a secured device * Single stepping is not possible on a secured device 6.8 6.8.1 Instruction Set Addressing Modes For the ease of implementation the architecture is a strict Load/Store RISC machine, which means all operations must have one of the eight general purpose registers R0 ... R7 as their source as well their destination. All word accesses must work with a word aligned address, that is A[0] = 0! MC9S12XDP512 Data Sheet, Rev. 2.21 208 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.8.1.1 Naming Conventions RD RD.L RD.H RS, RS1, RS2 RS.L, RS1.L, RS2.L RS.H, RS1.H, RS2.H RB RI RI+ -RI Destination register, allowed range is R0-R7 Low byte of the destination register, bits [7:0] High byte of the destination register, bits [15:8] Source register, allowed range is R0-R7 Low byte of the source register, bits [7:0] High byte of the source register, bits[15:8] Base register for indexed addressing modes, allowed range is R0-R7 Offset register for indexed addressing modes with register offset, allowed range is R0-R7 Offset register for indexed addressing modes with register offset and post-increment, Allowed range is R0-R7 (R0+ is equivalent to R0) Offset register for indexed addressing modes with register offset and pre-decrement, Allowed range is R0-R7 (-R0 is equivalent to R0) NOTE Even though register R1 is intended to be used as a pointer to the variable segment, it may be used as a general purpose data register as well. Selecting R0 as destination register will discard the result of the instruction. Only the condition code register will be updated 6.8.1.2 Inherent Addressing Mode (INH) Instructions that use this addressing mode either have no operands or all operands are in internal XGATE registers:. Examples BRK RTS 6.8.1.3 Immediate 3-Bit Wide (IMM3) Operands for immediate mode instructions are included in the instruction stream and are fetched into the instruction queue along with the rest of the 16 bit instruction. The '#' symbol is used to indicate an immediate addressing mode operand. This address mode is used for semaphore instructions. Examples: CSEM SSEM #1 #3 ; Unlock semaphore 1 ; Lock Semaphore 3 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 209 Chapter 6 XGATE (S12XGATEV2) 6.8.1.4 Immediate 4 Bit Wide (IMM4) The 4 bit wide immediate addressing mode is supported by all shift instructions. RD = RD imm4 Examples: LSL LSR 6.8.1.5 R4,#1 R4,#3 ; R4 = R4 << 1; shift register R4 by 1 bit to the left ; R4 = R4 >> 3; shift register R4 by 3 bits to the right Immediate 8 Bit Wide (IMM8) The 8 bit wide immediate addressing mode is supported by four major commands (ADD, SUB, LD, CMP). RD = RD imm8 Examples: ADDL SUBL LDH CMPL 6.8.1.6 R1,#1 R2,#2 R3,#3 R4,#4 ; ; ; ; adds an 8 bit value to register R1 subtracts an 8 bit value from register R2 loads an 8 bit immediate into the high byte of Register R3 compares the low byte of register R4 with an immediate value Immediate 16 Bit Wide (IMM16) The 16 bit wide immediate addressing mode is a construct to simplify assembler code. Instructions which offer this mode are translated into two opcodes using the eight bit wide immediate addressing mode. RD = RD imm16 Examples: LDW ADD 6.8.1.7 R4,#$1234 R4,#$5678 ; translated to LDL R4,#$34; LDH R4,#$12 ; translated to ADDL R4,#$78; ADDH R4,#$56 Monadic Addressing (MON) In this addressing mode only one operand is explicitly given. This operand can either be the source (f(RD)), the target (RD = f()), or both source and target of the operation (RD = f(RD)). Examples: JAL SIF R1 R2 ; PC = R1, R1 = PC+2 ; Trigger IRQ associated with the channel number in R2.L MC9S12XDP512 Data Sheet, Rev. 2.21 210 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.8.1.8 Dyadic Addressing (DYA) In this mode the result of an operation between two registers is stored in one of the registers used as operands. RD = RD RS is the general register to register format, with register RD being the first operand and RS the second. RD and RS can be any of the 8 general purpose registers R0 ... R7. If R0 is used as the destination register, only the condition code flags are updated. This addressing mode is used only for shift operations with a variable shift value Examples: LSL LSR 6.8.1.9 R4,R5 R4,R5 ; R4 = R4 << R5 ; R4 = R4 >> R5 Triadic Addressing (TRI) In this mode the result of an operation between two or three registers is stored into a third one. RD = RS1 RS2 is the general format used in the order RD, RS1, RS1. RD, RS1, RS2 can be any of the 8 general purpose registers R0 ... R7. If R0 is used as the destination register RD, only the condition code flags are updated. This addressing mode is used for all arithmetic and logical operations. Examples: ADC SUB 6.8.1.10 R5,R6,R7 R5,R6,R7 ; R5 = R6 + R7 + Carry ; R5 = R6 - R7 Relative Addressing 9-Bit Wide (REL9) A 9-bit signed word address offset is included in the instruction word. This addressing mode is used for conditional branch instructions. Examples: BCC BEQ 6.8.1.11 REL9 REL9 ; PC = PC + 2 + (REL9 << 1) ; PC = PC + 2 + (REL9 << 1) Relative Addressing 10-Bit Wide (REL10) An 11-bit signed word address offset is included in the instruction word. This addressing mode is used for the unconditional branch instruction. Examples: BRA 6.8.1.12 REL10 ; PC = PC + 2 + (REL10 << 1) Index Register plus Immediate Offset (IDO5) (RS, #offset5) provides an unsigned offset from the base register. Examples: LDB STW R4,(R1,#offset) R4,(R1,#offset) ; loads a byte from R1+offset into R4 ; stores R4 as a word to R1+offset MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 211 Chapter 6 XGATE (S12XGATEV2) 6.8.1.13 Index Register plus Register Offset (IDR) For load and store instructions (RS, RI) provides a variable offset in a register. Examples: LDB STW 6.8.1.14 R4,(R1,R2) R4,(R1,R2) ; loads a byte from R1+R2 into R4 ; stores R4 as a word to R1+R2 Index Register plus Register Offset with Post-increment (IDR+) [RS, RI+] provides a variable offset in a register, which is incremented after accessing the memory. In case of a byte access the index register will be incremented by one. In case of a word access it will be incremented by two. Examples: LDB STW 6.8.1.15 R4,(R1,R2+) R4,(R1,R2+) ; loads a byte from R1+R2 into R4, R2+=1 ; stores R4 as a word to R1+R2, R2+=2 Index Register plus Register Offset with Pre-decrement (-IDR) [RS, -RI] provides a variable offset in a register, which is decremented before accessing the memory. In case of a byte access the index register will be decremented by one. In case of a word access it will be decremented by two. Examples: LDB STW 6.8.2 R4,(R1,-R2) R4,(R1,-R2) ; R2 -=1, loads a byte from R1+R2 into R4 ; R2 -=2, stores R4 as a word to R1+R2 Instruction Summary and Usage 6.8.2.1 Load & Store Instructions Any register can be loaded either with an immediate or from the address space using indexed addressing modes. LDL LDW RD,#IMM8 RD,(RB,RI) ; loads an immediate 8 bit value to the lower byte of RD ; loads data using RB+RI as effective address LDB RD,(RB, RI+) ; loads data using RB+RI as effective address ; followed by an increment of RI depending on ; the size of the operation The same set of modes is available for the store instructions STB RS,(RB, RI) ; stores data using RB+RI as effective address STW RS,(RB, RI+) ; stores data using RB+RI as effective address ; followed by an increment of RI depending on ; the size of the operation. MC9S12XDP512 Data Sheet, Rev. 2.21 212 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.8.2.2 Logic and Arithmetic Instructions All logic and arithmetic instructions support the 8 bit immediate addressing mode (IMM8: RD = RD #IMM8) and the triadic addressing mode (TRI: RD = RS1 RS2). All arithmetic is considered as signed, sign, overflow, zero and carry flag will be updated. The carry will not be affected for logical operations. ADDL ANDH R2,#1 R4,#$FE ; increment R2 ; R4.H = R4.H & $FE, clear lower bit of higher byte ADD SUB R3,R4,R5 R3,R4,R5 ; R3 = R4 + R5 ; R3 = R4 - R5 AND OR R3,R4,R5 R3,R4,R5 ; R3 = R4 & R5 logical AND on the whole word ; R3 = R4 | R5 6.8.2.3 Register - Register Transfers This group comprises transfers from and to some special registers TFR R3,CCR ; transfers the condition code register to the low byte of ; register R3 Branch Instructions The branch offset is +255 words or -256 words counted from the beginning of the next instruction. Since instructions have a fixed 16 bit width, the branch offsets are word aligned by shifting the offset value by 2. BEQ label ; if Z flag = 1 branch to label An unconditional branch allows a +511 words or -512 words branch distance. BRA 6.8.2.4 label Shift Instructions Shift operations allow the use of a 4 bit wide immediate value to identify a shift width within a 16 bit word. For shift operations a value of 0 does not shift at all, while a value of 15 shifts the register RD by 15 bits. In a second form the shift value is contained in the bits 3:0 of the register RS. Examples: LSL LSR ASR R4,#1 R4,#3 R4,R2 ; R4 = R4 << 1; shift register R4 by 1 bit to the left ; R4 = R4 >> 3; shift register R4 by 3 bits to the right ; R4 = R4 >> R2;arithmetic shift register R4 right by the amount ; of bits contained in R2[3:0]. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 213 Chapter 6 XGATE (S12XGATEV2) 6.8.2.5 Bit Field Operations This addressing mode is used to identify the position and size of a bit field for insertion or extraction. The width and offset are coded in the lower byte of the source register 2, RS2. The content of the upper byte is ignored. An offset of 0 denotes the right most position and a width of 0 denotes 1 bit. These instructions are very useful to extract, insert, clear, set or toggle portions of a 16 bit word. W4 O4 5 2 W4=3, O4=2 15 RS2 0 RS1 Bit Field Extract Bit Field Insert 15 3 0 RD Figure 6-23. Bit Field Addressing BFEXT 6.8.2.6 R3,R4,R5 ; R5: W4 bits offset O4, will be extracted from R4 into R3 Special Instructions for DMA Usage The XGATE offers a number of additional instructions for flag manipulation, program flow control and debugging: 1. SIF: Set a channel interrupt flag 2. SSEM: Test and set a hardware semaphore 3. CSEM: Clear a hardware semaphore 4. BRK: Software breakpoint 5. NOP: No Operation 6. RTS: Terminate the current thread MC9S12XDP512 Data Sheet, Rev. 2.21 214 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.8.3 Cycle Notation Table 6-16 show the XGATE access detail notation. Each code letter equals one XGATE cycle. Each letter implies additional wait cycles if memories or peripherals are not accessible. Memories or peripherals are not accessible if they are blocked by the S12X_CPU. In addition to this Peripherals are only accessible every other XGATE cycle. Uppercase letters denote 16 bit operations. Lowercase letters denote 8 bit operations. The XGATE is able to perform two bus or wait cycles per S12X_CPU cycle. Table 6-16. Access Detail Notation V -- Vector fetch: always an aligned word read, lasts for at least one RISC core cycle P -- Program word fetch: always an aligned word read, lasts for at least one RISC core cycle r -- 8 bit data read: lasts for at least one RISC core cycle R -- 16 bit data read: lasts for at least one RISC core cycle w -- 8 bit data write: lasts for at least one RISC core cycle W -- 16 bit data write: lasts for at least one RISC core cycle A -- Alignment cycle: no read or write, lasts for zero or one RISC core cycles f -- Free cycle: no read or write, lasts for one RISC core cycles Special Cases PP/P -- Branch: PP if branch taken, P if not 6.8.4 Thread Execution When the RISC core is triggered by an interrupt request (see Figure 6-1) it first executes a vector fetch sequence which performs three bus accesses: 1. A V-cycle to fetch the initial content of the program counter. 2. A V-cycle to fetch the initial content of the data segment pointer (R1). 3. A P-cycle to load the initial opcode. Afterwards a sequence of instructions (thread) is executed which is terminated by an "RTS" instruction. If further interrupt requests are pending after a thread has been terminated, a new vector fetch will be performed. Otherwise the RISC core will idle until a new interrupt request is received. A thread can not be interrupted by an interrupt request. 6.8.5 Instruction Glossary This section describes the XGATE instruction set in alphabetical order. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 215 Chapter 6 XGATE (S12XGATEV2) ADC ADC Add with Carry Operation RS1 + RS2 + C RD Adds the content of register RS1, the content of register RS2 and the value of the Carry bit using binary addition and stores the result in the destination register RD. The Zero Flag is also carried forward from the previous operation allowing 32 and more bit additions. Example: ADC ADC BCC R6,R2,R2 R7,R3,R3 ; R7:R6 = R5:R4 + R3:R2 ; conditional branch on 32 bit addition CCR Effects N Z V C N: Set if bit 15 of the result is set; cleared otherwise. Z: Set if the result is $0000 and Z was set before this operation; cleared otherwise. V: Set if a twos complement overflow resulted from the operation; cleared otherwise. RS1[15] & RS2[15] & RD[15]new | RS1[15] & RS2[15] & RD[15]new C: Set if there is a carry from bit 15 of the result; cleared otherwise. RS1[15] & RS2[15] | RS1[15] & RD[15]new | RS2[15] & RD[15]new Code and CPU Cycles Source Form ADC RD, RS1, RS2 Address Mode TRI Machine Code 0 0 0 1 1 RD RS1 Cycles RS2 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 216 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) ADD ADD Add without Carry Operation RS1 + RS2 RD RD + IMM16 RD (translates to ADDL RD, #IMM16[7:0]; ADDH RD, #[15:8]) Performs a 16 bit addition and stores the result in the destination register RD. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS1[15] & RS2[15] & RD[15]new | RS1[15] & RS2[15] & RD[15]new Refer to ADDH instruction for #IMM16 operations. Set if there is a carry from bit 15 of the result; cleared otherwise. RS1[15] & RS2[15] | RS1[15] & RD[15]new | RS2[15] & RD[15]new Refer to ADDH instruction for #IMM16 operations. Code and CPU Cycles Source Form Address Mode Machine Code RS1 Cycles ADD RD, RS1, RS2 TRI 0 0 0 1 1 RD RS2 1 0 P ADD RD, #IMM16 IMM8 1 1 1 0 0 RD IMM16[7:0] P IMM8 1 1 1 0 1 RD IMM16[15:8] P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 217 Chapter 6 XGATE (S12XGATEV2) ADDH ADDH Add Immediate 8 bit Constant (High Byte) Operation RD + IMM8:$00 RD Adds the content of high byte of register RD and a signed immediate 8 bit constant using binary addition and stores the result in the high byte of the destination register RD. This instruction can be used after an ADDL for a 16 bit immediate addition. Example: ADDL ADDH R2,#LOWBYTE R2,#HIGHBYTE ; R2 = R2 + 16 bit immediate CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RD[15]old & IMM8[7] & RD[15]new | RD[15]old & IMM8[7] & RD[15]new Set if there is a carry from the bit 15 of the result; cleared otherwise. RD[15]old & IMM8[7] | RD[15]old & RD[15]new | IMM8[7] & RD[15]new Code and CPU Cycles Source Form ADDH RD, #IMM8 Address Mode IMM8 Machine Code 1 1 1 0 1 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 218 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) ADDL Add Immediate 8 bit Constant (Low Byte) ADDL Operation RD + $00:IMM8 RD Adds the content of register RD and an unsigned immediate 8 bit constant using binary addition and stores the result in the destination register RD. This instruction must be used first for a 16 bit immediate addition in conjunction with the ADDH instruction. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the 8 bit operation; cleared otherwise. RD[15]old & RD[15]new Set if there is a carry from the bit 15 of the result; cleared otherwise. RD[15]old & RD[15]new Code and CPU Cycles Source Form ADDL RD, #IMM8 Address Mode IMM8 Machine Code 1 1 1 0 0 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 219 Chapter 6 XGATE (S12XGATEV2) AND AND Logical AND Operation RS1 & RS2 RD RD & IMM16 RD (translates to ANDL RD, #IMM16[7:0]; ANDH RD, #IMM16[15:8]) Performs a bit wise logical AND of two 16 bit values and stores the result in the destination register RD. Remark: There is no complement to the BITH and BITL functions. This can be imitated by using R0 as a destination register. AND R0, RS1, RS2 performs a bit wise test without storing a result. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Refer to ANDH instruction for #IMM16 operations. 0; cleared. Not affected. Code and CPU Cycles Source Form AND RD, RS1, RS2 AND RD, #IMM16 Address Mode Machine Code RS1 Cycles TRI 0 0 0 1 0 RD RS2 0 0 P IMM8 1 0 0 0 0 RD IMM16[7:0] P IMM8 1 0 0 0 1 RD IMM16[15:8] P MC9S12XDP512 Data Sheet, Rev. 2.21 220 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) ANDH Logical AND Immediate 8 bit Constant (High Byte) ANDH Operation RD.H & IMM8 RD.H Performs a bit wise logical AND between the high byte of register RD and an immediate 8 bit constant and stores the result in the destination register RD.H. The low byte of RD is not affected. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form ANDH RD, #IMM8 Address Mode IMM8 Machine Code 1 0 0 0 1 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 221 Chapter 6 XGATE (S12XGATEV2) ANDL Logical AND Immediate 8 bit Constant (Low Byte) ANDL Operation RD.L & IMM8 RD.L Performs a bit wise logical AND between the low byte of register RD and an immediate 8 bit constant and stores the result in the destination register RD.L. The high byte of RD is not affected. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 7 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form ANDL RD, #IMM8 Address Mode IMM8 Machine Code 1 0 0 0 0 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 222 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) ASR ASR Arithmetic Shift Right Operation n b15 RD C n = RS or IMM4 Shifts the bits in register RD n positions to the right. The higher n bits of the register RD become filled with the sign bit (RD[15]). The carry flag will be updated to the bit contained in RD[n-1] before the shift for n > 0. n can range from 0 to 16. In immediate address mode, n is determined by the operand IMM4. n is considered to be 16 in IMM4 is equal to 0. In dyadic address mode, n is determined by the content of RS. n is considered to be 16 if the content of RS is greater than 15. CCR Effects N Z V C 0 N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RD[15]old ^ RD[15]new Set if n > 0 and RD[n-1] = 1; if n = 0 unaffected. Code and CPU Cycles Source Form ASR RD, #IMM4 ASR RD, RS Address Mode Machine Code IMM4 0 0 0 0 1 RD IMM4 DYA 0 0 0 0 1 RD RS Cycles 1 1 0 0 1 P 0 0 0 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 223 Chapter 6 XGATE (S12XGATEV2) BCC BCC Branch if Carry Cleared (Same as BHS) Operation If C = 0, then PC + $0002 + (REL9 << 1) PC Tests the Carry flag and branches if C = 0. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BCC REL9 Address Mode REL9 Machine Code 0 0 1 0 0 0 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 224 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BCS BCS Branch if Carry Set (Same as BLO) Operation If C = 1, then PC + $0002 + (REL9 << 1) PC Tests the Carry flag and branches if C = 1. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BCS REL9 Address Mode REL9 Machine Code 0 0 1 0 0 0 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 225 Chapter 6 XGATE (S12XGATEV2) BEQ BEQ Branch if Equal Operation If Z = 1, then PC + $0002 + (REL9 << 1) PC Tests the Zero flag and branches if Z = 1. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BEQ REL9 Address Mode REL9 Machine Code 0 0 1 0 0 1 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 226 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BFEXT BFEXT Bit Field Extract Operation RS1[(o+w):o] RD[w:0]; 0 RD[15:(w+1)] w = (RS2[7:4]) o = (RS2[3:0]) Extracts w+1 bits from register RS1 starting at position o and writes them right aligned into register RD. The remaining bits in RD will be cleared. If (o+w) > 15 only bits [15:o] get extracted. 15 7 4 3 0 W4 15 O4 5 2 RS2 0 W4=3, O4=2 RS1 Bit Field Extract 15 3 0 0 RD CCR Effects N Z V C 0 0 N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form BFEXT RD, RS1, RS2 Address Mode TRI Machine Code 0 1 1 0 0 RD RS1 Cycles RS2 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 227 Chapter 6 XGATE (S12XGATEV2) BFFO BFFO Bit Field Find First One Operation FirstOne (RS) RD; Searches the first "1" in register RS (from MSB to LSB) and writes the bit position into the destination register RD. The upper bits of RD are cleared. In case the content of RS is equal to $0000, RD will be cleared and the carry flag will be set. This is used to distinguish a "1" in position 0 versus no "1" in the whole RS register at all. CCR Effects N Z V C 0 0 N: Z: V: C: 1 0; cleared. Set if the result is $0000; cleared otherwise. 0; cleared. Set if RS = $00001; cleared otherwise. Before executing the instruction Code and CPU Cycles Source Form BFFO RD, RS Address Mode DYA Machine Code 0 0 0 0 1 RD RS Cycles 1 0 0 0 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 228 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BFINS BFINS Bit Field Insert Operation RS1[w:0] RD[(w+o):o]; w = (RS2[7:4]) o = (RS2[3:0]) Extracts w+1 bits from register RS1 starting at position 0 and writes them into register RD starting at position o. The remaining bits in RD are not affected. If (o+w) > 15 the upper bits are ignored. Using R0 as a RS1, this command can be used to clear bits. 15 7 4 3 0 W4 O4 15 3 RS2 0 RS1 Bit Field Insert 15 5 2 0 W4=3, O4=2 RD CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form BFINS RD, RS1, RS2 Address Mode TRI Machine Code 0 1 1 0 1 RD RS1 Cycles RS2 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 229 Chapter 6 XGATE (S12XGATEV2) BFINSI BFINSI Bit Field Insert and Invert Operation !RS1[w:0] RD[w+o:o]; w = (RS2[7:4]) o = (RS2[3:0]) Extracts w+1 bits from register RS1 starting at position 0, inverts them and writes into register RD starting at position o. The remaining bits in RD are not affected. If (o+w) > 15 the upper bits are ignored. Using R0 as a RS1, this command can be used to set bits. 15 7 4 3 0 W4 O4 15 RS2 3 0 RS1 Inverted Bit Field Insert 15 5 2 W4=3, O4=2 0 RD CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form BFINSI RD, RS1, RS2 Address Mode TRI Machine Code 0 1 1 1 0 RD RS1 Cycles RS2 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 230 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BFINSX BFINSX Bit Field Insert and XNOR Operation !(RS1[w:0] ^ RD[w+o:o]) RD[w+o:o]; w = (RS2[7:4]) o = (RS2[3:0]) Extracts w+1 bits from register RS1 starting at position 0, performs an XNOR with RD[w+o:o] and writes the bits back io RD. The remaining bits in RD are not affected. If (o+w) > 15 the upper bits are ignored. Using R0 as a RS1, this command can be used to toggle bits. 15 7 4 3 0 W4 O4 15 RS2 3 0 RS1 Bit Field Insert XNOR 15 5 2 W4=3, O4=2 0 RD CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form BFINSX RD, RS1, RS2 Address Mode TRI Machine Code 0 1 1 1 1 RD RS1 Cycles RS2 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 231 Chapter 6 XGATE (S12XGATEV2) BGE BGE Branch if Greater than or Equal to Zero Operation If N ^ V = 0, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare signed numbers. Branch if RS1 RS2: SUB BGE R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BGE REL9 Address Mode REL9 Machine Code 0 0 1 1 0 1 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 232 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BGT BGT Branch if Greater than Zero Operation If Z | (N ^ V) = 0, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare signed numbers. Branch if RS1 > RS2: SUB BGE R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BGT REL9 Address Mode REL9 Machine Code 0 0 1 1 1 0 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 233 Chapter 6 XGATE (S12XGATEV2) BHI BHI Branch if Higher Operation If C | Z = 0, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare unsigned numbers. Branch if RS1 > RS2: SUB BHI R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BHI REL9 Address Mode REL9 Machine Code 0 0 1 1 0 0 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 234 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BHS BHS Branch if Higher or Same (Same as BCC) Operation If C = 0, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare unsigned numbers. Branch if RS1 RS2: SUB BHS R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BHS REL9 Address Mode REL9 Machine Code 0 0 1 0 0 0 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 235 Chapter 6 XGATE (S12XGATEV2) BITH BITH Bit Test Immediate 8 bit Constant (High Byte) Operation RD.H & IMM8 NONE Performs a bit wise logical AND between the high byte of register RD and an immediate 8 bit constant. Only the condition code flags get updated, but no result is written back CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form BITH RD, #IMM8 Address Mode IMM8 Machine Code 1 0 0 1 1 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 236 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BITL BITL Bit Test Immediate 8 bit Constant (Low Byte) Operation RD.L & IMM8 NONE Performs a bit wise logical AND between the low byte of register RD and an immediate 8 bit constant. Only the condition code flags get updated, but no result is written back. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 7 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form BITL RD, #IMM8 Address Mode IMM8 Machine Code 1 0 0 1 0 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 237 Chapter 6 XGATE (S12XGATEV2) BLE BLE Branch if Less or Equal to Zero Operation If Z | (N ^ V) = 1, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare signed numbers. Branch if RS1 RS2: SUB BLE R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BLE REL9 Address Mode REL9 Machine Code 0 0 1 1 1 0 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 238 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BLO BLO Branch if Carry Set (Same as BCS) Operation If C = 1, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare unsigned numbers. Branch if RS1 < RS2: SUB BLO R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BLO REL9 Address Mode REL9 Machine Code 0 0 1 0 0 0 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 239 Chapter 6 XGATE (S12XGATEV2) BLS BLS Branch if Lower or Same Operation If C | Z = 1, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare unsigned numbers. Branch if RS1 RS2: SUB BLS R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BLS REL9 Address Mode REL9 Machine Code 0 0 1 1 0 0 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 240 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BLT BLT Branch if Lower than Zero Operation If N ^ V = 1, then PC + $0002 + (REL9 << 1) PC Branch instruction to compare signed numbers. Branch if RS1 < RS2: SUB BLT R0,RS1,RS2 REL9 CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BLT REL9 Address Mode REL9 Machine Code 0 0 1 1 0 1 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 241 Chapter 6 XGATE (S12XGATEV2) BMI BMI Branch if Minus Operation If N = 1, then PC + $0002 + (REL9 << 1) PC Tests the Sign flag and branches if N = 1. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BMI REL9 Address Mode REL9 Machine Code 0 0 1 0 1 0 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 242 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BNE BNE Branch if Not Equal Operation If Z = 0, then PC + $0002 + (REL9 << 1) PC Tests the Zero flag and branches if Z = 0. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BNE REL9 Address Mode REL9 Machine Code 0 0 1 0 0 1 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 243 Chapter 6 XGATE (S12XGATEV2) BPL BPL Branch if Plus Operation If N = 0, then PC + $0002 + (REL9 << 1) PC Tests the Sign flag and branches if N = 0. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BPL REL9 Address Mode REL9 Machine Code 0 0 1 0 1 0 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 244 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BRA BRA Branch Always Operation PC + $0002 + (REL10 << 1) PC Branches always CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BRA REL10 Address Mode REL10 Machine Code 0 0 1 1 1 1 Cycles REL10 PP MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 245 Chapter 6 XGATE (S12XGATEV2) BRK BRK Break Operation Put XGATE into Debug Mode (see Section 6.6.2, "Entering Debug Mode")and signals a Software breakpoint to the S12X_DBG module (see section 4.9 of the S12X_DBG Section). NOTE It is not possible to single step over a BRK instruction. This instruction does not advance the program counter. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BRK Address Mode INH Machine Code 0 0 0 0 0 0 0 0 0 0 Cycles 0 0 0 0 0 0 PAff MC9S12XDP512 Data Sheet, Rev. 2.21 246 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) BVC BVC Branch if Overflow Cleared Operation If V = 0, then PC + $0002 + (REL9 << 1) PC Tests the Overflow flag and branches if V = 0. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BVC REL9 Address Mode REL9 Machine Code 0 0 1 0 1 1 0 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 247 Chapter 6 XGATE (S12XGATEV2) BVS BVS Branch if Overflow Set Operation If V = 1, then PC + $0002 + (REL9 << 1) PC Tests the Overflow flag and branches if V = 1. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form BVS REL9 Address Mode REL9 Machine Code 0 0 1 0 1 1 1 Cycles REL9 PP/P MC9S12XDP512 Data Sheet, Rev. 2.21 248 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) CMP CMP Compare Operation RS2 - RS1 NONE (translates to SUB R0, RS1, RS2) RD - IMM16 NONE (translates to CMPL RD, #IMM16[7:0]; CPCH RD, #IMM16[15:8]) Subtracts two 16 bit values and discards the result. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS1[15] & RS2[15] & result[15] | RS1[15] & RS2[15] & result[15] RD[15] & IMM16[15] & result[15] | RD[15] & IMM16[15] & result[15] Set if there is a carry from the bit 15 of the result; cleared otherwise. RS1[15] & RS2[15] | RS1[15] & result[15] | RS2[15] & result[15] RD[15] & IMM16[15] | RD[15] & result[15] | IMM16[15] & result[15] Code and CPU Cycles Source Form CMP RS1, RS2 CMP RS, #IMM16 Address Mode Machine Code 0 0 0 RS1 Cycles TRI 0 0 0 1 1 RS2 0 0 P IMM8 1 1 0 1 0 RS IMM16[7:0] P IMM8 1 1 0 1 1 RS IMM16[15:8] P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 249 Chapter 6 XGATE (S12XGATEV2) CMPL Compare Immediate 8 bit Constant (Low Byte) CMPL Operation RS.L - IMM8 NONE, only condition code flags get updated Subtracts the 8 bit constant IMM8 contained in the instruction code from the low byte of the source register RS.L using binary subtraction and updates the condition code register accordingly. Remark: There is no equivalent operation using triadic addressing. Comparing the values of two registers can be performed by using the subtract instruction with R0 as destination register. CCR Effects N Z V C N: Z: V: C: Set if bit 7 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. Set if a twos complement overflow resulted from the 8 bit operation; cleared otherwise. RS[7] & IMM8[7] & result[7] | RS[7] & IMM8[7] & result[7] Set if there is a carry from the Bit 7 to Bit 8 of the result; cleared otherwise. RS[7] & IMM8[7] | RS[7] & result[7] | IMM8[7] & result[7] Code and CPU Cycles Source Form CMPL RS, #IMM8 Address Mode IMM8 Machine Code 1 1 0 1 0 RS Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 250 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) COM COM One's Complement Operation ~RS RD (translates to XNOR RD, R0, RS) ~RD RD (translates to XNOR RD, R0, RD) Performs a one's complement on a general purpose register. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form Address Mode Machine Code Cycles COM RD, RS TRI 0 0 0 1 0 RD 0 0 0 RS 1 1 P COM RD TRI 0 0 0 1 0 RD 0 0 0 RD 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 251 Chapter 6 XGATE (S12XGATEV2) CPC CPC Compare with Carry Operation RS2 - RS1 - C NONE (translates to SBC R0, RS1, RS2) Subtracts the carry bit and the content of register RS2 from the content of register RS1 using binary subtraction and discards the result. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS1[15] & RS2[15] & result[15] | RS1[15] & RS2[15] & result[15] Set if there is a carry from the bit 15 of the result; cleared otherwise. RS1[15] & RS2[15] | RS1[15] & result[15] | RS2[15] & result[15] Code and CPU Cycles Source Form CPC RS1, RS2 Address Mode TRI Machine Code 0 0 0 1 1 0 0 0 RS1 Cycles RS2 0 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 252 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) CPCH CPCH Compare Immediate 8 bit Constant with Carry (High Byte) Operation RS.H - IMM8 - C NONE, only condition code flags get updated Subtracts the carry bit and the 8 bit constant IMM8 contained in the instruction code from the high byte of the source register RD using binary subtraction and updates the condition code register accordingly. The carry bit and Zero bits are taken into account to allow a 16 bit compare in the form of CMPL CPCH BCC R2,#LOWBYTE R2,#HIGHBYTE ; branch condition Remark: There is no equivalent operation using triadic addressing. Comparing the values of two registers can be performed by using the subtract instruction with R0 as destination register. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $00 and Z was set before this operation; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS[15] & IMM8[7] & result[15] | RS[15] & IMM8[7] & result[15] Set if there is a carry from the bit 15 of the result; cleared otherwise. RS[15] & IMM8[7] | RS[15] & result[15] | IMM8[7] & result[15] Code and CPU Cycles Source Form CPCH RD, #IMM8 Address Mode IMM8 Machine Code 1 1 0 1 1 RS Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 253 Chapter 6 XGATE (S12XGATEV2) CSEM CSEM Clear Semaphore Operation Unlocks a semaphore that was locked by the RISC core. In monadic address mode, bits RS[2:0] select the semaphore to be cleared. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form Address Mode Machine Code Cycles CSEM #IMM3 IMM3 0 0 0 0 0 IMM3 1 1 1 1 0 0 0 0 PA CSEM RS MON 0 0 0 0 0 RS 1 1 1 1 0 0 0 1 PA MC9S12XDP512 Data Sheet, Rev. 2.21 254 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) CSL CSL Logical Shift Left with Carry Operation n C RD C C C C n bits n = RS or IMM4 Shifts the bits in register RD n positions to the left. The lower n bits of the register RD become filled with the carry flag. The carry flag will be updated to the bit contained in RD[16-n] before the shift for n > 0. n can range from 0 to 16. In immediate address mode, n is determined by the operand IMM4. n is considered to be 16 in IMM4 is equal to 0. In dyadic address mode, n is determined by the content of RS. n is considered to be 16 if the content of RS is greater than 15. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RD[15]old ^ RD[15]new Set if n > 0 and RD[16-n] = 1; if n = 0 unaffected. Code and CPU Cycles Source Form CSL RD, #IMM4 CSL RD, RS Address Mode Machine Code IMM4 0 0 0 0 1 RD IMM4 DYA 0 0 0 0 1 RD RS Cycles 1 1 0 1 0 P 0 0 1 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 255 Chapter 6 XGATE (S12XGATEV2) CSR CSR Logical Shift Right with Carry Operation n C C C C RD C n bits n = RS or IMM4 Shifts the bits in register RD n positions to the right. The higher n bits of the register RD become filled with the carry flag. The carry flag will be updated to the bit contained in RD[n-1] before the shift for n > 0. n can range from 0 to 16. In immediate address mode, n is determined by the operand IMM4. n is considered to be 16 in IMM4 is equal to 0. In dyadic address mode, n is determined by the content of RS. n is considered to be 16 if the content of RS is greater than 15. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RD[15]old ^ RD[15]new Set if n > 0 and RD[n-1] = 1; if n = 0 unaffected. Code and CPU Cycles Source Form CSR RD, #IMM4 CSR RD, RS Address Mode Machine Code IMM4 0 0 0 0 1 RD IMM4 DYA 0 0 0 0 1 RD RS Cycles 1 1 0 1 1 P 0 0 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 256 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) JAL JAL Jump and Link Operation PC + $0002 RD; RD PC Jumps to the address stored in RD and saves the return address in RD. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form JAL RD Address Mode MON Machine Code 0 0 0 0 0 RD 1 1 Cycles 1 1 0 1 1 0 PP MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 257 Chapter 6 XGATE (S12XGATEV2) LDB LDB Load Byte from Memory (Low Byte) Operation M[RB, #OFFS5 RD.L; $00 RD.H M[RB, RI] RD.L; $00 RD.H M[RB, RI] RD.L; $00 RD.H; RI+1 RI;1 RI-1 RI; M[RS, RI] RD.L; $00 RD.H Loads a byte from memory into the low byte of register RD. The high byte is cleared. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form LDB RD, (RB, #OFFS5) Address Mode Machine Code Cycles IDO5 0 1 0 0 0 RD RB OFFS5 Pr LDB RD, (RS, RI) IDR 0 1 1 0 0 RD RB RI 0 0 Pr LDB RD, (RS, RI+) IDR+ 0 1 1 0 0 RD RB RI 0 1 Pr LDB RD, (RS, -RI) -IDR 0 1 1 0 0 RD RB RI 1 0 Pr 1.If the same general purpose register is used as index (RI) and destination register (RD), the content of the register will not be incremented after the data move: M[RB, RI] RD.L; $00 RD.H MC9S12XDP512 Data Sheet, Rev. 2.21 258 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) LDH LDH Load Immediate 8 bit Constant (High Byte) Operation IMM8 RD.H; Loads an eight bit immediate constant into the high byte of register RD. The low byte is not affected. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form LDH RD, #IMM8 Address Mode IMM8 Machine Code 1 1 1 1 1 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 259 Chapter 6 XGATE (S12XGATEV2) LDL LDL Load Immediate 8 bit Constant (Low Byte) Operation IMM8 RD.L; $00 RD.H Loads an eight bit immediate constant into the low byte of register RD. The high byte is cleared. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form LDL RD, #IMM8 Address Mode IMM8 Machine Code 1 1 1 1 0 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 260 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) LDW LDW Load Word from Memory Operation M[RB, #OFFS5] RD M[RB, RI] RD M[RB, RI] RD; RI+2 RI1 RI-2 RI; M[RS, RI] RD IMM16 RD (translates to LDL RD, #IMM16[7:0]; LDH RD, #IMM16[15:8]) Loads a 16 bit value into the register RD. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form LDW RD, (RB, #OFFS5) Address Mode Machine Code Cycles IDO5 0 1 0 0 1 RD RB OFFS5 PR LDW RD, (RB, RI) IDR 0 1 1 0 1 RD RB RI 0 0 PR LDW RD, (RB, RI+) IDR+ 0 1 1 0 1 RD RB RI 0 1 PR LDW RD, (RB, -RI) -IDR 0 1 1 0 1 RD RB RI 1 0 PR LDW RD, #IMM16 IMM8 1 1 1 1 0 RD IMM16[7:0] P IMM8 1 1 1 1 1 RD IMM16[15:8] P 1. If the same general purpose register is used as index (RI) and destination register (RD), the content of the register will not be incremented after the data move: M[RB, RI] RD MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 261 Chapter 6 XGATE (S12XGATEV2) LSL LSL Logical Shift Left Operation n C RD 0 0 0 0 n bits n = RS or IMM4 Shifts the bits in register RD n positions to the left. The lower n bits of the register RD become filled with zeros. The carry flag will be updated to the bit contained in RD[16-n] before the shift for n > 0. n can range from 0 to 16. In immediate address mode, n is determined by the operand IMM4. n is considered to be 16 in IMM4 is equal to 0. In dyadic address mode, n is determined by the content of RS. n is considered to be 16 if the content of RS is greater than 15. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RD[15]old ^ RD[15]new Set if n > 0 and RD[16-n] = 1; if n = 0 unaffected. Code and CPU Cycles Source Form LSL RD, #IMM4 LSL RD, RS Address Mode Machine Code IMM4 0 0 0 0 1 RD IMM4 DYA 0 0 0 0 1 RD RS Cycles 1 1 1 0 0 P 0 1 0 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 262 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) LSR LSR Logical Shift Right Operation n 0 0 0 0 RD C n bits n = RS or IMM4 Shifts the bits in register RD n positions to the right. The higher n bits of the register RD become filled with zeros. The carry flag will be updated to the bit contained in RD[n-1] before the shift for n > 0. n can range from 0 to 16. In immediate address mode, n is determined by the operand IMM4. n is considered to be 16 in IMM4 is equal to 0. In dyadic address mode, n is determined by the content of RS. n is considered to be 16 if the content of RS is greater than 15. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RD[15]old ^ RD[15]new Set if n > 0 and RD[n-1] = 1; if n = 0 unaffected. Code and CPU Cycles Source Form LSR RD, #IMM4 LSR RD, RS Address Mode Machine Code IMM4 0 0 0 0 1 RD IMM4 DYA 0 0 0 0 1 RD RS Cycles 1 1 1 0 1 P 0 1 0 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 263 Chapter 6 XGATE (S12XGATEV2) MOV MOV Move Register Content Operation RS RD (translates to OR RD, R0, RS) Copies the content of RS to RD. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form MOV RD, RS Address Mode TRI Machine Code 0 0 0 1 0 RD 0 0 Cycles 0 RS 1 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 264 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) NEG NEG Two's Complement Operation -RS RD (translates to SUB RD, R0, RS) -RD RD (translates to SUB RD, R0, RD) Performs a two's complement on a general purpose register. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS[15] & RD[15]new Set if there is a carry from the bit 15 of the result; cleared otherwise RS[15] | RD[15]new Code and CPU Cycles Source Form Address Mode Machine Code Cycles NEG RD, RS TRI 0 0 0 1 1 RD 0 0 0 RS 0 0 P NEG RD TRI 0 0 0 1 1 RD 0 0 0 RD 0 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 265 Chapter 6 XGATE (S12XGATEV2) NOP NOP No Operation Operation No Operation for one cycle. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form NOP Address Mode INH Machine Code 0 0 0 0 0 0 0 1 0 0 Cycles 0 0 0 0 0 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 266 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) OR OR Logical OR Operation RS1 | RS2 RD RD | IMM16 RD (translates to ORL RD, #IMM16[7:0]; ORH RD, #IMM16[15:8] Performs a bit wise logical OR between two 16 bit values and stores the result in the destination register RD. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Refer to ORH instruction for #IMM16 operations. 0; cleared. Not affected. Code and CPU Cycles Source Form OR RD, RS1, RS2 OR RD, #IMM16 Address Mode Machine Code RS1 Cycles TRI 0 0 0 1 0 RD RS2 1 0 P IMM8 1 0 1 0 0 RD IMM16[7:0] P IMM8 1 0 1 0 1 RD IMM16[15:8] P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 267 Chapter 6 XGATE (S12XGATEV2) ORH ORH Logical OR Immediate 8 bit Constant (High Byte) Operation RD.H | IMM8 RD.H Performs a bit wise logical OR between the high byte of register RD and an immediate 8 bit constant and stores the result in the destination register RD.H. The low byte of RD is not affected. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form ORH RD, #IMM8 Address Mode IMM8 Machine Code 1 0 1 0 1 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 268 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) ORL ORL Logical OR Immediate 8 bit Constant (Low Byte) Operation RD.L | IMM8 RD.L Performs a bit wise logical OR between the low byte of register RD and an immediate 8 bit constant and stores the result in the destination register RD.L. The high byte of RD is not affected. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 7 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form ORL RD, #IMM8 Address Mode IMM8 Machine Code 1 0 1 0 0 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 269 Chapter 6 XGATE (S12XGATEV2) PAR PAR Calculate Parity Operation Calculates the number of ones in the register RD. The Carry flag will be set if the number is odd, otherwise it will be cleared. CCR Effects N Z V C 0 0 N: Z: V: C: 0; cleared. Set if RD is $0000; cleared otherwise. 0; cleared. Set if there the number of ones in the register RD is odd; cleared otherwise. Code and CPU Cycles Source Form PAR, RD Address Mode MON Machine Code 0 0 0 0 0 RD 1 1 Cycles 1 1 0 1 0 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 270 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) ROL ROL Rotate Left Operation RD n bits n = RS or IMM4 Rotates the bits in register RD n positions to the left. The lower n bits of the register RD are filled with the upper n bits. Two source forms are available. In the first form, the parameter n is contained in the instruction code as an immediate operand. In the second form, the parameter is contained in the lower bits of the source register RS[3:0]. All other bits in RS are ignored. If n is zero, no shift will take place and the register RD will be unaffected; however, the condition code flags will be updated. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form ROL RD, #IMM4 ROL RD, RS Address Mode Machine Code IMM4 0 0 0 0 1 RD IMM4 DYA 0 0 0 0 1 RD RS Cycles 1 1 1 1 0 P 0 1 1 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 271 Chapter 6 XGATE (S12XGATEV2) ROR ROR Rotate Right Operation RD n bits n = RS or IMM4 Rotates the bits in register RD n positions to the right. The upper n bits of the register RD are filled with the lower n bits. Two source forms are available. In the first form, the parameter n is contained in the instruction code as an immediate operand. In the second form, the parameter is contained in the lower bits of the source register RS[3:0]. All other bits in RS are ignored. If n is zero no shift will take place and the register RD will be unaffected; however, the condition code flags will be updated. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form ROR RD, #IMM4 ROR RD, RS Address Mode Machine Code IMM4 0 0 0 0 1 RD IMM4 DYA 0 0 0 0 1 RD RS Cycles 1 1 1 1 1 P 0 1 1 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 272 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) RTS RTS Return to Scheduler Operation Terminates the current thread of program execution and remains idle until a new thread is started by the hardware scheduler. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form RTS Address Mode INH Machine Code 0 0 0 0 0 0 1 0 0 0 Cycles 0 0 0 0 0 0 PA MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 273 Chapter 6 XGATE (S12XGATEV2) SBC SBC Subtract with Carry Operation RS1 - RS2 - C RD Subtracts the content of register RS2 and the value of the Carry bit from the content of register RS1 using binary subtraction and stores the result in the destination register RD. Also the zero flag is carried forward from the previous operation allowing 32 and more bit subtractions. Example: SUB SBC BCC R6,R4,R2 R7,R5,R3 ; R7:R6 = R5:R4 - R3:R2 ; conditional branch on 32 bit subtraction CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000 and Z was set before this operation; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS1[15] & RS2[15] & RD[15]new | RS1[15] & RS2[15] & RD[15]new Set if there is a carry from bit 15 of the result; cleared otherwise. RS1[15] & RS2[15] | RS1[15] & RD[15]new | RS2[15] & RD[15]new Code and CPU Cycles Source Form SBC RD, RS1, RS2 Address Mode TRI Machine Code 0 0 0 1 1 RD RS1 Cycles RS2 0 1 P MC9S12XDP512 Data Sheet, Rev. 2.21 274 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) SEX SEX Sign Extend Byte to Word Operation The result in RD is the 16 bit sign extended representation of the original two's complement number in the low byte of RD.L. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form SEX RD Address Mode MON Machine Code 0 0 0 0 0 RD 1 1 Cycles 1 1 0 1 0 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 275 Chapter 6 XGATE (S12XGATEV2) SIF SIF Set Interrupt Flag Operation Sets the Interrupt Flag of an XGATE Channel. This instruction supports two source forms. If inherent address mode is used, then the interrupt flag of the current channel (XGCHID) will be set. If the monadic address form is used, the interrupt flag associated with the channel id number contained in RS[6:0] is set. The content of RS[15:7] is ignored. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form SIF SIF RS Address Mode Machine Code INH 0 0 0 0 0 MON 0 0 0 0 0 0 1 1 RS Cycles 0 0 0 0 0 0 0 0 PA 1 1 1 1 0 1 1 1 PA MC9S12XDP512 Data Sheet, Rev. 2.21 276 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) SSEM SSEM Set Semaphore Operation Attempts to set a semaphore. The state of the semaphore will be stored in the Carry-Flag: 1 = Semaphore is locked by the RISC core 0 = Semaphore is locked by the S12X_CPU In monadic address mode, bits RS[2:0] select the semaphore to be set. CCR Effects N Z V C -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Set if semaphore is locked by the RISC core; cleared otherwise. Code and CPU Cycles Source Form Address Mode Machine Code Cycles SSEM #IMM3 IMM3 0 0 0 0 0 IMM3 1 1 1 1 0 0 1 0 PA SSEM RS MON 0 0 0 0 0 RS 1 1 1 1 0 0 1 1 PA MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 277 Chapter 6 XGATE (S12XGATEV2) STB STB Store Byte to Memory (Low Byte) Operation RS.L M[RB, #OFFS5] RS.L M[RB, RI] RS.L M[RB, RI]; RI+1 RI; RI-1 RI; RS.L M[RB, RI]1 Stores the low byte of register RD to memory. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form STB RS, (RB, #OFFS5), Address Mode Machine Code Cycles IDO5 0 1 0 1 0 RS RB OFFS5 Pw STB RS, (RB, RI) IDR 0 1 1 1 0 RS RB RI 0 0 Pw STB RS, (RB, RI+) IDR+ 0 1 1 1 0 RS RB RI 0 1 Pw STB RS, (RB, -RI) -IDR 0 1 1 1 0 RS RB RI 1 0 Pw 1. If the same general purpose register is used as index (RI) and source register (RS), the unmodified content of the source register is written to the memory: RS.L M[RB, RS-1]; RS-1 RS MC9S12XDP512 Data Sheet, Rev. 2.21 278 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) STW STW Store Word to Memory Operation RS M[RB, #OFFS5] RS M[RB, RI] RS M[RB, RI]; RI+2 RI; RI-2 RI; RS M[RB, RI]1 Stores the content of register RS to memory. CCR Effects N Z V C -- -- -- -- N: Z: V: C: Not affected. Not affected. Not affected. Not affected. Code and CPU Cycles Source Form STW RS, (RB, #OFFS5) Address Mode Machine Code Cycles IDO5 0 1 0 1 1 RS RB OFFS5 PW STW RS, (RB, RI) IDR 0 1 1 1 1 RS RB RI 0 0 PW STW RS, (RB, RI+) IDR+ 0 1 1 1 1 RS RB RI 0 1 PW STW RS, (RB, -RI) -IDR 0 1 1 1 1 RS RB RI 1 0 PW 1. If the same general purpose register is used as index (RI) and source register (RS), the unmodified content of the source register is written to the memory: RS M[RB, RS-2]; RS-2 RS MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 279 Chapter 6 XGATE (S12XGATEV2) SUB SUB Subtract without Carry Operation RS1 - RS2 RD RD - IMM16 RD (translates to SUBL RD, #IMM16[7:0]; SUBH RD, #IMM16{15:8]) Subtracts two 16 bit values and stores the result in the destination register RD. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS1[15] & RS2[15] & RD[15]new | RS1[15] & RS2[15] & RD[15]new Refer to SUBH instruction for #IMM16 operations. Set if there is a carry from the bit 15 of the result; cleared otherwise. RS1[15] & RS2[15] | RS1[15] & RD[15]new | RS2[15] & RD[15]new Refer to SUBH instruction for #IMM16 operations. Code and CPU Cycles Source Form SUB RD, RS1, RS2 SUB RD, #IMM16 Address Mode Machine Code RS1 Cycles TRI 0 0 0 1 1 RD RS2 0 0 P IMM8 1 1 0 0 0 RD IMM16[7:0] P IMM8 1 1 0 0 1 RD IMM16[15:8] P MC9S12XDP512 Data Sheet, Rev. 2.21 280 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) SUBH SUBH Subtract Immediate 8 bit Constant (High Byte) Operation RD - IMM8:$00 RD Subtracts a signed immediate 8 bit constant from the content of high byte of register RD and using binary subtraction and stores the result in the high byte of destination register RD. This instruction can be used after an SUBL for a 16 bit immediate subtraction. Example: SUBL SUBH R2,#LOWBYTE R2,#HIGHBYTE ; R2 = R2 - 16 bit immediate CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RD[15]old & IMM8[7] & RD[15]new | RD[15]old & IMM8[7] & RD[15]new Set if there is a carry from the bit 15 of the result; cleared otherwise. RD[15]old & IMM8[7] | RD[15]old & RD[15]new | IMM8[7] & RD[15]new Code and CPU Cycles Source Form SUBH RD, #IMM8 Address Mode IMM8 Machine Code 1 1 0 0 1 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 281 Chapter 6 XGATE (S12XGATEV2) SUBL Subtract Immediate 8 bit Constant (Low Byte) SUBL Operation RD - $00:IMM8 RD Subtracts an immediate 8 bit constant from the content of register RD using binary subtraction and stores the result in the destination register RD. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the 8 bit operation; cleared otherwise. RD[15]old & RD[15]new Set if there is a carry from the bit 15 of the result; cleared otherwise. RD[15]old & RD[15]new Code and CPU Cycles Source Form SUBL RD, #IMM8 Address Mode IMM8 Machine Code 1 1 0 0 0 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 282 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) TFR TFR Transfer from and to Special Registers Operation TFR RD,CCR: CCR RD[3:0]; 0 RD[15:4] TFR CCR,RD: RD[3:0] CCR TFR RD,PC: PC+4 RD Transfers the content of one RISC core register to another. The TFR RD,PC instruction can be used to implement relative subroutine calls. Example: RETADDR SUBR TFR BRA ... ... JAL R7,PC SUBR ;Return address (RETADDR) is stored in R7 ;Relative branch to subroutine (SUBR) R7 ;Jump to return address (RETADDR) CCR Effects TFR RD,CCR, TFR RD,PC: TFR CCR,RS: N Z V C N Z V C -- -- -- -- Not affected. Not affected. Not affected. Not affected. N: Z: V: C: N: Z: V: C: RS[3]. RS[2]. RS[1]. RS[0]. Code and CPU Cycles Source Form Address Mode Machine Code Cycles TFR RD,CCR CCR RD MON 0 0 0 0 0 RD 1 1 1 1 1 0 0 0 P TFR CCR,RS RS CCR MON 0 0 0 0 0 RS 1 1 1 1 1 0 0 1 P TFR RD,PCPC+4 RD MON 0 0 0 0 0 RD 1 1 1 1 1 0 1 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 283 Chapter 6 XGATE (S12XGATEV2) TST TST Test Register Operation RS - 0 NONE (translates to SUB R0, RS, R0) Subtracts zero from the content of register RS using binary subtraction and discards the result. CCR Effects N Z V C N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Set if a twos complement overflow resulted from the operation; cleared otherwise. RS[15] & result[15] Set if there is a carry from the bit 15 of the result; cleared otherwise. RS1[15] & result[15] Code and CPU Cycles Source Form TST RS Address Mode TRI Machine Code 0 0 0 1 1 0 0 0 RS1 Cycles 0 0 0 0 0 P MC9S12XDP512 Data Sheet, Rev. 2.21 284 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) XNOR XNOR Logical Exclusive NOR Operation ~(RS1 ^ RS2) RD ~(RD ^ IMM16) RD (translates to XNOR RD, #IMM16{15:8]; XNOR RD, #IMM16[7:0]) Performs a bit wise logical exclusive NOR between two 16 bit values and stores the result in the destination register RD. Remark: Using R0 as a source registers will calculate the one's complement of the other source register. Using R0 as both source operands will fill RD with $FFFF. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the result is $0000; cleared otherwise. Refer to XNORH instruction for #IMM16 operations. 0; cleared. Not affected. Code and CPU Cycles Source Form XNOR RD, RS1, RS2 XNOR RD, #IMM16 Address Mode Machine Code RS1 Cycles TRI 0 0 0 1 0 RD RS2 1 1 P IMM8 1 0 1 1 0 RD IMM16[7:0] P IMM8 1 0 1 1 1 RD IMM16[15:8] P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 285 Chapter 6 XGATE (S12XGATEV2) XNORH Logical Exclusive NOR Immediate 8 bit Constant (High Byte) XNORH Operation ~(RD.H ^ IMM8) RD.H Performs a bit wise logical exclusive NOR between the high byte of register RD and an immediate 8 bit constant and stores the result in the destination register RD.H. The low byte of RD is not affected. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 15 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form XNORH RD, #IMM8 Address Mode IMM8 Machine Code 1 0 1 1 1 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 286 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) XNORL Logical Exclusive NOR Immediate 8 bit Constant (Low Byte) XNORL Operation ~(RD.L ^ IMM8) RD.L Performs a bit wise logical exclusive NOR between the low byte of register RD and an immediate 8 bit constant and stores the result in the destination register RD.L. The high byte of RD is not affected. CCR Effects N Z V C 0 -- N: Z: V: C: Set if bit 7 of the result is set; cleared otherwise. Set if the 8 bit result is $00; cleared otherwise. 0; cleared. Not affected. Code and CPU Cycles Source Form XNORL RD, #IMM8 Address Mode IMM8 Machine Code 1 0 1 1 0 RD Cycles IMM8 P MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 287 Chapter 6 XGATE (S12XGATEV2) 6.8.6 Instruction Coding Table 6-17 summarizes all XGATE instructions in the order of their machine coding. Table 6-17. Instruction Set Summary (Sheet 1 of 3) Functionality Return to Scheduler and Others BRK NOP RTS SIF Semaphore Instructions CSEM IMM3 CSEM RS SSEM IMM3 SSEM RS Single Register Instructions SEX RD PAR RD JAL RD SIF RS Special Move instructions TFR RD,CCR TFR CCR,RS TFR RD,PC Shift instructions Dyadic BFFO RD, RS ASR RD, RS CSL RD, RS CSR RD, RS LSL RD, RS LSR RD, RS ROL RD, RS ROR RD, RS Shift instructions immediate ASR RD, #IMM4 CSL RD, #IMM4 CSR RD, #IMM4 LSL RD, #IMM4 LSR RD, #IMM4 ROL RD, #IMM4 ROR RD, #IMM4 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 IMM3 RS IMM3 RS 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RD RD RD RS 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RD RS RD 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 RD RD RD RD RD RD RD RD 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 RD RD RD RD RD RD RD 1 1 1 1 1 1 1 0 0 0 1 1 1 1 0 1 1 0 0 1 1 1 0 1 0 1 0 1 RS RS RS RS RS RS RS RS IMM4 IMM4 IMM4 IMM4 IMM4 IMM4 IMM4 MC9S12XDP512 Data Sheet, Rev. 2.21 288 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) Table 6-17. Instruction Set Summary (Sheet 2 of 3) Functionality Logical Triadic AND RD, RS1, RS2 OR RD, RS1, RS2 XNOR RD, RS1, RS2 Arithmetic Triadic SUB RD, RS1, RS2 SBC RD, RS1, RS2 ADD RD, RS1, RS2 ADC RD, RS1, RS2 Branches BCC REL9 BCS REL9 BNE REL9 BEQ REL9 BPL REL9 BMI REL9 BVC REL9 BVS REL9 BHI REL9 BLS REL9 BGE REL9 BLT REL9 BGT REL9 BLE REL9 BRA REL10 Load and Store Instructions LDB RD, (RB, #OFFS5) LDW RD, (RB, #OFFS5) STB RS, (RB, #OFFS5) STW RS, (RB, #OFFS5) LDB RD, (RB, RI) LDW RD, (RB, RI) STB RS, (RB, RI) STW RS, (RB, RI) LDB RD, (RB, RI+) LDW RD, (RB, RI+) STB RS, (RB, RI+) STW RS, (RB, RI+) LDB RD, (RB, -RI) LDW RD, (RB, -RI) STB RS, (RB, -RI) STW RS, (RB, -RI) Bit Field Instructions BFEXT RD, RS1, RS2 BFINS RD, RS1, RS2 BFINSI RD, RS1, RS2 BFINSX RD, RS1, RS2 Logic Immediate Instructions ANDL RD, #IMM8 15 14 13 12 11 10 9 8 7 6 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 RD RD RS RS RD RD RS RS RD RD RS RS RD RD RS RS RB RB RB RB RB RB RB RB RB RB RB RB RB RB RB RB 0 0 0 0 1 1 1 1 1 1 1 1 0 0 1 1 0 1 0 1 RD RD RD RD RS1 RS1 RS1 RS1 1 0 0 0 0 RD 5 4 3 2 1 0 0 1 1 0 0 1 0 0 1 1 0 1 0 1 RI RI RI RI RI RI RI RI RI RI RI RI 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 RS2 RS2 RS2 RS2 1 1 1 1 1 1 1 1 RD RS1 RS2 RD RS1 RS2 RD RS1 RS2 For compare use SUB R0,Rs1,Rs2 RD RS1 RS2 RD RS1 RS2 RD RS1 RS2 RD RS1 RS2 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL9 REL10 OFFS5 OFFS5 OFFS5 OFFS5 IMM8 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 289 Chapter 6 XGATE (S12XGATEV2) Table 6-17. Instruction Set Summary (Sheet 3 of 3) Functionality ANDH RD, #IMM8 BITL RD, #IMM8 BITH RD, #IMM8 ORL RD, #IMM8 ORH RD, #IMM8 XNORL RD, #IMM8 XNORH RD, #IMM8 Arithmetic Immediate Instructions SUBL RD, #IMM8 SUBH RD, #IMM8 CMPL RS, #IMM8 CPCH RS, #IMM8 ADDL RD, #IMM8 ADDH RD, #IMM8 LDL RD, #IMM8 LDH RD, #IMM8 15 14 13 12 11 10 9 8 7 6 5 4 3 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1 1 0 0 1 1 1 0 1 0 1 0 1 RD RD RD RD RD RD RD IMM8 IMM8 IMM8 IMM8 IMM8 IMM8 IMM8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 RD RD RS RS RD RD RD RD IMM8 IMM8 IMM8 IMM8 IMM8 IMM8 IMM8 IMM8 2 1 0 MC9S12XDP512 Data Sheet, Rev. 2.21 290 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) 6.9 Initialization and Application Information 6.9.1 Initialization The recommended initialization of the XGATE is as follows: 1. Clear the XGE bit to suppress any incoming service requests. 2. Make sure that no thread is running on the XGATE. This can be done in several ways: a) Poll the XGCHID register until it reads $00. Also poll XGDBG and XGSWEIF to make sure that the XGATE has not been stopped. b) Enter Debug Mode by setting the XGDBG bit. Clear the XGCHID register. Clear the XGDBG bit. The recommended method is a). 3. Set the XGVBR register to the lowest address of the XGATE vector space. 4. Clear all Channel ID flags. 5. Copy XGATE vectors and code into the RAM. 6. Initialize the S12X_INT module. 7. Enable the XGATE by setting the XGE bit. The following code example implements the XGATE initialization sequence. 6.9.2 Code Example (Transmit "Hello World!" on SCI) SCI_REGS SCIBDH SCIBDL SCICR2 SCISR1 SCIDRL TIE TE RE SCI_VEC CPU S12X ;########################################### ;# SYMBOLS # ;########################################### EQU $00C8 ;SCI register space EQU SCI_REGS+$00 ;SCI Baud Rate Register EQU SCI_REGS+$00 ;SCI Baud Rate Register EQU SCI_REGS+$03 ;SCI Control Register 2 EQU SCI_REGS+$04 ;SCI Status Register 1 EQU SCI_REGS+$07 ;SCI Control Register 2 EQU $80 ;TIE bit mask EQU $08 ;TE bit mask EQU $04 ;RE bit mask EQU $D6 ;SCI vector number INT_REGS INT_CFADDR INT_CFDATA RQST EQU EQU EQU EQU INT_REGS+$07 INT_REGS+$08 $80 $0120 ;S12X_INT register space ;Interrupt Configuration Address Register ;Interrupt Configuration Data Registers ;RQST bit mask XGATE_REGS XGMCTL XGMCTL_CLEAR XGMCTL_ENABLE XGCHID XGVBR XGIF EQU EQU EQU EQU EQU EQU EQU $0380 XGATE_REGS+$00 $FA02 $8282 XGATE_REGS+$02 XGATE_REGS+$06 XGATE_REGS+$08 ;XGATE register space ;XGATE Module Control Register ;Clear all XGMCTL bits ;Enable XGATE ;XGATE Channel ID Register ;XGATE ISP Select Register ;XGATE Interrupt Flag Vector MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 291 Chapter 6 XGATE (S12XGATEV2) XGSWT XGSEM EQU EQU XGATE_REGS+$18 XGATE_REGS+$1A ;XGATE Software Trigger Register ;XGATE Semaphore Register RPAGE EQU $0016 RAM_SIZE EQU 32*$400 RAM_START RAM_START_XG RAM_START_GLOB EQU EQU EQU $1000 $10000-RAM_SIZE $100000-RAM_SIZE XGATE_VECTORS XGATE_VECTORS_XG EQU EQU RAM_START RAM_START_XG XGATE_DATA XGATE_DATA_XG EQU EQU RAM_START+(4*128) RAM_START_XG+(4*128) XGATE_CODE XGATE_CODE_XG EQU EQU XGATE_DATA+(XGATE_CODE_FLASH-XGATE_DATA_FLASH) XGATE_DATA_XG+(XGATE_CODE_FLASH-XGATE_DATA_FLASH) BUS_FREQ_HZ EQU 40000000 ;32k RAM ;########################################### ;# S12XE VECTOR TABLE # ;########################################### ORG $FF10 ;non-maskable interrupts DW DUMMY_ISR DUMMY_ISR DUMMY_ISR DUMMY_ISR ORG DW $FFF4 ;non-maskable interrupts DUMMY_ISR DUMMY_ISR DUMMY_ISR ;########################################### ;# DISABLE COP # ;########################################### ORG $FF0E DW $FFFE ORG $C000 START_OF_CODE ;########################################### ;# INITIALIZE S12XE CORE # ;########################################### SEI MOVB #(RAM_START_GLOB>>12), RPAGE;set RAM page INIT_SCI INIT_INT ;########################################### ;# INITIALIZE SCI # ;########################################### MOVW #(BUS_FREQ_HZ/(16*9600)), SCIBDH;set baud rate MOVB #(TIE|TE), SCICR2;enable tx buffer empty interrupt ;########################################### ;# INITIALIZE S12X_INT # ;########################################### MOVB #(SCI_VEC&$F0), INT_CFADDR ;switch SCI interrupts to XGATE MOVB #RQST|$01, INT_CFDATA+((SCI_VEC&$0F)>>1) MC9S12XDP512 Data Sheet, Rev. 2.21 292 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) INIT_XGATE INIT_XGATE_BUSY_LOOP ;########################################### ;# INITIALIZE XGATE # ;########################################### MOVW #XGMCTL_CLEAR , XGMCTL;clear all XGMCTL bits TST BNE XGCHID ;wait until current thread is finished INIT_XGATE_BUSY_LOOP LDX LDD STD STD STD STD STD STD STD STD #XGIF #$FFFF 2,X+ 2,X+ 2,X+ 2,X+ 2,X+ 2,X+ 2,X+ 2,X+ ;clear all channel interrupt flags MOVW #XGATE_VECTORS_XG, XGVBR;set vector base register MOVW #$FF00, XGSWT INIT_XGATE_VECTAB_LOOP ;clear all software triggers ;########################################### ;# INITIALIZE XGATE VECTOR TABLE # ;########################################### LDAA #128 ;build XGATE vector table LDY #XGATE_VECTORS MOVW #XGATE_DUMMY_ISR_XG, 4,Y+ DBNE A, INIT_XGATE_VECTAB_LOOP MOVW #XGATE_CODE_XG, RAM_START+(2*SCI_VEC) MOVW #XGATE_DATA_XG, RAM_START+(2*SCI_VEC)+2 COPY_XGATE_CODE COPY_XGATE_CODE_LOOP START_XGATE DUMMY_ISR ;########################################### ;# COPY XGATE CODE # ;########################################### LDX #XGATE_DATA_FLASH MOVW 2,X+, 2,Y+ MOVW 2,X+, 2,Y+ MOVW 2,X+, 2,Y+ MOVW 2,X+, 2,Y+ CPX #XGATE_CODE_FLASH_END BLS COPY_XGATE_CODE_LOOP ;########################################### ;# START XGATE # ;########################################### MOVW #XGMCTL_ENABLE, XGMCTL;enable XGATE BRA * ;########################################### ;# DUMMY INTERRUPT SERVICE ROUTINE # ;########################################### RTI CPU XGATE MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 293 Chapter 6 XGATE (S12XGATEV2) XGATE_DATA_FLASH XGATE_DATA_SCI XGATE_DATA_IDX XGATE_DATA_MSG XGATE_CODE_FLASH XGATE_CODE_DONE XGATE_CODE_FLASH_END XGATE_DUMMY_ISR_XG ;########################################### ;# XGATE DATA # ;########################################### ALIGN 1 EQU * EQU *-XGATE_DATA_FLASH DW SCI_REGS ;pointer to SCI register space EQU *-XGATE_DATA_FLASH DB XGATE_DATA_MSG ;string pointer EQU *-XGATE_DATA_FLASH FCC "Hello World! ;ASCII string DB $0D ;CR ;########################################### ;# XGATE CODE # ;########################################### ALIGN 1 LDW R2,(R1,#XGATE_DATA_SCI);SCI -> R2 LDB R3,(R1,#XGATE_DATA_IDX);msg -> R3 LDB R4,(R1,R3+) ;curr. char -> R4 STB R3,(R1,#XGATE_DATA_IDX);R3 -> idx LDB R0,(R2,#(SCISR1-SCI_REGS));initiate SCI transmit STB R4,(R2,#(SCIDRL-SCI_REGS));initiate SCI transmit CMPL R4,#$0D BEQ XGATE_CODE_DONE RTS LDL R4,#$00 ;disable SCI interrupts STB R4,(R2,#(SCICR2-SCI_REGS)) LDL R3,#XGATE_DATA_MSG;reset R3 STB R3,(R1,#XGATE_DATA_IDX) RTS EQU (XGATE_CODE_FLASH_END-XGATE_CODE_FLASH)+XGATE_CODE_XG MC9S12XDP512 Data Sheet, Rev. 2.21 294 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 295 Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 296 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 297 Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 298 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 299 Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 300 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 301 Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 302 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 303 Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 304 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 305 Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 306 Freescale Semiconductor Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 307 Chapter 6 XGATE (S12XGATEV2) MC9S12XDP512 Data Sheet, Rev. 2.21 308 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.1 Introduction The HCS12 enhanced capture timer module has the features of the HCS12 standard timer module enhanced by additional features in order to enlarge the field of applications, in particular for automotive ABS applications. This design specification describes the standard timer as well as the additional features. The basic timer consists of a 16-bit, software-programmable counter driven by a prescaler. This timer can be used for many purposes, including input waveform measurements while simultaneously generating an output waveform. Pulse widths can vary from microseconds to many seconds. A full access for the counter registers or the input capture/output compare registers will take place in one clock cycle. Accessing high byte and low byte separately for all of these registers will not yield the same result as accessing them in one word. 7.1.1 * * * * 7.1.2 * * * * Features 16-bit buffer register for four input capture (IC) channels. Four 8-bit pulse accumulators with 8-bit buffer registers associated with the four buffered IC channels. Configurable also as two 16-bit pulse accumulators. 16-bit modulus down-counter with 8-bit prescaler. Four user-selectable delay counters for input noise immunity increase. Modes of Operation Stop -- Timer and modulus counter are off since clocks are stopped. Freeze -- Timer and modulus counter keep on running, unless the TSFRZ bit in the TSCR1 register is set to one. Wait -- Counters keep on running, unless the TSWAI bit in the TSCR1 register is set to one. Normal -- Timer and modulus counter keep on running, unless the TEN bit in the TSCR1 register or the MCEN bit in the MCCTL register are cleared. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 309 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.1.3 Block Diagram Bus Clock Prescaler Channel 0 Input Capture 16-bit Counter Output Compare Channel 1 Input Capture Modulus Counter Interrupt 16-Bit Modulus Counter Output Compare IOC0 IOC1 Channel 2 Input Capture Output Compare Timer Overflow Interrupt Timer Channel 0 Interrupt Channel 3 Input Capture Output Compare Registers Channel 4 Input Capture Output Compare Channel 5 Input Capture Output Compare Timer Channel 7 Interrupt PA Overflow Interrupt PA Input Interrupt PB Overflow Interrupt 16-Bit Pulse Accumulator A 16-Bit Pulse Accumulator B Channel 6 Input Capture Output Compare Channel 7 Input Capture IOC2 IOC3 IOC4 IOC5 IOC6 IOC7 Output Compare Figure 7-1. ECT Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 310 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.2 External Signal Description The ECT module has a total of eight external pins. 7.2.1 IOC7 -- Input Capture and Output Compare Channel 7 This pin serves as input capture or output compare for channel 7. 7.2.2 IOC6 -- Input Capture and Output Compare Channel 6 This pin serves as input capture or output compare for channel 6. 7.2.3 IOC5 -- Input Capture and Output Compare Channel 5 This pin serves as input capture or output compare for channel 5. 7.2.4 IOC4 -- Input Capture and Output Compare Channel 4 This pin serves as input capture or output compare for channel 4. 7.2.5 IOC3 -- Input Capture and Output Compare Channel 3 This pin serves as input capture or output compare for channel 3. 7.2.6 IOC2 -- Input Capture and Output Compare Channel 2 This pin serves as input capture or output compare for channel 2. 7.2.7 IOC1 -- Input Capture and Output Compare Channel 1 This pin serves as input capture or output compare for channel 1. 7.2.8 IOC0 -- Input Capture and Output Compare Channel 0 This pin serves as input capture or output compare for channel 0. NOTE For the description of interrupts see Section 7.4.3, "Interrupts". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 311 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3 Memory Map and Register Definition This section provides a detailed description of all memory and registers. 7.3.1 Module Memory Map The memory map for the ECT module is given below in Table 7-1. The address listed for each register is the address offset. The total address for each register is the sum of the base address for the ECT module and the address offset for each register. Table 7-1. ECT Memory Map Address Offset Register Access 0x0000 Timer Input Capture/Output Compare Select (TIOS) R/W 0x0001 Timer Compare Force Register (CFORC) R/W1 0x0002 Output Compare 7 Mask Register (OC7M) R/W 0x0003 Output Compare 7 Data Register (OC7D) R/W 0x0004 Timer Count Register High (TCNT) R/W2 0x0005 Timer Count Register Low (TCNT) R/W2 0x0006 Timer System Control Register 1 (TSCR1) R/W 0x0007 Timer Toggle Overflow Register (TTOV) R/W 0x0008 Timer Control Register 1 (TCTL1) R/W 0x0009 Timer Control Register 2 (TCTL2) R/W 0x000A Timer Control Register 3 (TCTL3) R/W 0x000B Timer Control Register 4 (TCTL4) R/W 0x000C Timer Interrupt Enable Register (TIE) R/W 0x000D Timer System Control Register 2 (TSCR2) R/W 0x000E Main Timer Interrupt Flag 1 (TFLG1) R/W 0x000F Main Timer Interrupt Flag 2 (TFLG2) R/W 0x0010 Timer Input Capture/Output Compare Register 0 High (TC0) R/W3 0x0011 Timer Input Capture/Output Compare Register 0 Low (TC0) R/W3 0x0012 Timer Input Capture/Output Compare Register 1 High (TC1) R/W3 0x0013 Timer Input Capture/Output Compare Register 1 Low (TC1) R/W3 0x0014 Timer Input Capture/Output Compare Register 2 High (TC2) R/W3 0x0015 Timer Input Capture/Output Compare Register 2 Low (TC2) R/W3 0x0016 Timer Input Capture/Output Compare Register 3 High (TC3) R/W3 0x0017 Timer Input Capture/Output Compare Register 3 Low (TC3) R/W3 0x0018 Timer Input Capture/Output Compare Register 4 High (TC4) R/W3 0x0019 Timer Input Capture/Output Compare Register 4 Low (TC4) R/W3 0x001A Timer Input Capture/Output Compare Register 5 High (TC5) R/W3 0x001B Timer Input Capture/Output Compare Register 5 Low (TC5) R/W3 0x001C Timer Input Capture/Output Compare Register 6 High (TC6) R/W3 0x001D Timer Input Capture/Output Compare Register 6 Low (TC6) R/W3 MC9S12XDP512 Data Sheet, Rev. 2.21 312 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Table 7-1. ECT Memory Map (continued) Address Offset Register Access 0x001E Timer Input Capture/Output Compare Register 7 High (TC7) R/W3 0x001F Timer Input Capture/Output Compare Register 7 Low (TC7) R/W3 0x0020 16-Bit Pulse Accumulator A Control Register (PACTL) R/W 0x0021 Pulse Accumulator A Flag Register (PAFLG) R/W 0x0022 Pulse Accumulator Count Register 3 (PACN3) R/W 0x0023 Pulse Accumulator Count Register 2 (PACN2) R/W 0x0024 Pulse Accumulator Count Register 1 (PACN1) R/W 0x0025 Pulse Accumulator Count Register 0 (PACN0) R/W 0x0026 16-Bit Modulus Down Counter Register (MCCTL) R/W 0x0027 16-Bit Modulus Down Counter Flag Register (MCFLG) R/W 0x0028 Input Control Pulse Accumulator Register (ICPAR) R/W 0x0029 Delay Counter Control Register (DLYCT) R/W 0x002A Input Control Overwrite Register (ICOVW) R/W 0x002B Input Control System Control Register (ICSYS) R/W4 0x002C Reserved 0x002D Timer Test Register (TIMTST) R/W2 0x002E Precision Timer Prescaler Select Register (PTPSR) R/W 0x002F Precision Timer Modulus Counter Prescaler Select Register (PTMCPSR) R/W 0x0030 16-Bit Pulse Accumulator B Control Register (PBCTL) R/W 0x0031 16-Bit Pulse Accumulator B Flag Register (PBFLG) R/W 0x0032 8-Bit Pulse Accumulator Holding Register 3 (PA3H) R/W5 0x0033 8-Bit Pulse Accumulator Holding Register 2 (PA2H) R/W5 0x0034 8-Bit Pulse Accumulator Holding Register 1 (PA1H) R/W5 0x0035 8-Bit Pulse Accumulator Holding Register 0 (PA0H) R/W5 0x0036 Modulus Down-Counter Count Register High (MCCNT) R/W 0x0037 Modulus Down-Counter Count Register Low (MCCNT) R/W 0x0038 Timer Input Capture Holding Register 0 High (TC0H) R/W5 0x0039 Timer Input Capture Holding Register 0 Low (TC0H) R/W5 0x003A Timer Input Capture Holding Register 1 High(TC1H) R/W5 0x003B Timer Input Capture Holding Register 1 Low (TC1H) R/W5 0x003C Timer Input Capture Holding Register 2 High (TC2H) R/W5 0x003D Timer Input Capture Holding Register 2 Low (TC2H) R/W5 0x003E Timer Input Capture Holding Register 3 High (TC3H) R/W5 0x003F Timer Input Capture Holding Register 3 Low (TC3H) R/W5 -- 1 Always read 0x0000. Only writable in special modes (test_mode = 1). 3 Writes to these registers have no meaning or effect during input capture. 4 May be written once when not in test00mode but writes are always permitted when test00mode is enabled. 5 Writes have no effect. 2 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 313 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2 Register Descriptions This section consists of register descriptions in address order. Each description includes a standard register diagram with an associated figure number. Details of register bit and field function follow the register diagrams, in bit order. Register Name TIOS Bit 7 6 5 4 3 2 1 Bit 0 IOS7 IOS6 IOS5 IOS4 IOS3 IOS2 IOS1 IOS0 R 0 0 0 0 0 0 0 0 W FOC7 FOC6 FOC5 FOC4 FOC3 FOC2 FOC1 FOC0 OC7M7 OC7M6 OC7M5 OC7M4 OC7M3 OC7M2 OC7M1 OC7M0 OC7D7 OC7D6 OC7D5 OC7D4 OC7D3 OC7D2 OC7D1 OC7D0 TCNT15 TCNT14 TCNT13 TCNT12 TCNT11 TCNT10 TCNT9 TCNT8 TCNT7 TCNT6 TCNT5 TCNT4 TCNT3 TCNT2 TCNT1 TCNT0 TEN TSWAI TSFRZ TFFCA PRNT 0 0 0 TOV7 TOV6 TOV5 TOV4 TOV3 TOV2 TOV1 TOV0 OM7 OL7 OM6 OL6 OM5 OL5 OM4 OL4 OM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0 EDG7B EDG7A EDG6B EDG6A EDG5B EDG5A EDG4B EDG4A EDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG0A C7I C6I C5I C4I C3I C2I C1I C0I R W CFORC OC7M R W OC7D R W TCNT (High) R W TCNT (Low) R W TSCR1 R W TTOF R W TCTL1 R W TCTL2 R W TCTL3 R W TCTL4 R W TIE R W = Unimplemented or Reserved Figure 7-2. ECT Register Summary (Sheet 1 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 314 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Register Name TSCR2 Bit 7 R W TFLG1 R W TFLG2 R W TC0 (High) R W TC0 (Low) R W TC1 (High) R W TC1 (Low) R W TC2 (High) R W TC2 (Low) R W TC3 (High) R W TC3 (Low) R W TC4 (High) R W TC4 (Low) R W TC5 (High) R W TC5 (Low) R W 6 5 4 3 2 1 Bit 0 0 0 0 TCRE PR2 PR1 PR0 C6F C5F C4F C3F C2F C1F C0F 0 0 0 0 0 0 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TOI C7F TOF = Unimplemented or Reserved Figure 7-2. ECT Register Summary (Sheet 2 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 315 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Register Name TC6 (High) R W TC6 (Low) R W TC7 (High) R W TC7 (Low) R W PACTL R Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PAEN PAMOD PEDGE CLK1 CLK0 PA0VI PAI 0 0 0 0 0 PA0VF PAIF 0 W PAFLG R 0 W PACN3 R W PACN2 R W PACN1 R W PACN0 R W MCCTL R W MCFLG R W ICPAR R PACNT7(15) PACNT6(14) PACNT5(13) PACNT4(12) PACNT3(11) PACNT2(10) PACNT1(9) PACNT0(8) PACNT7 PACNT6 PACNT5 PACNT4 R W ICOVW R W PACNT2 PACNT1 PACNT0 PACNT7(15) PACNT6(14) PACNT5(13) PACNT4(12) PACNT3(11) PACNT2(10) PACNT1(9) PACNT0(8) PACNT7 PACNT6 PACNT5 PACNT4 PACNT3 MCZI MODMC RDMCL 0 0 ICLAT FLMC 0 0 0 0 0 0 0 DLY7 DLY6 DLY5 NOVW7 NOVW6 NOVW5 MCZF PACNT2 PACNT1 PACNT0 MCEN MCPR1 MCPR0 POLF3 POLF2 POLF1 POLF0 PA3EN PA2EN PA1EN PA0EN DLY4 DLY3 DLY2 DLY1 DLY0 NOVW4 NOVW3 NOVW2 NOVW1 NOVW0 W DLYCT PACNT3 = Unimplemented or Reserved Figure 7-2. ECT Register Summary (Sheet 3 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 316 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Register Name ICSYS R W Reserved Bit 7 6 5 4 3 2 1 Bit 0 SH37 SH26 SH15 SH04 TFMOD PACMX BUFEN LATQ R Reserved W TIMTST R Timer Test Register W PTPSR R W PTMCPSR R W PBCTL R PTPS7 PTPS6 PTPS5 PTPS4 PTPS3 PTPS2 PTPS1 PTPS0 PTMPS7 PTMPS6 PTMPS5 PTMPS4 PTMPS3 PTMPS2 PTMPS1 PTMPS0 0 0 0 0 0 W PBFLG R PBEN R 0 0 0 0 0 0 0 PA3H7 PA3H6 PA3H5 PA3H4 PA3H3 PA3H2 PA3H1 PA3H0 PA2H7 PA2H6 PA2H5 PA2H4 PA2H3 PA2H2 PA2H1 PA2H0 PA1H7 PA1H6 PA1H5 PA1H4 PA1H3 PA1H2 PA1H1 PA1H0 PA0H7 PA0H6 PA0H5 PA0H4 PA0H3 PA0H2 PA0H1 PA0H0 MCCNT15 MCCNT14 MCCNT13 MCCNT12 MCCNT11 MCCNT10 MCCNT9 MCCNT8 MCCNT7 MCCNT6 MCCNT5 MCCNT4 MCCNT3 MCCNT2 MCCNT1 MCCNT9 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 W PA3H PBOVI PBOVF 0 W PA2H R W PA1H R W PA0H R W MCCNT (High) MCCNT (Low) R W R W TC0H (High) R W TC0H (Low) R = Unimplemented or Reserved Figure 7-2. ECT Register Summary (Sheet 4 of 5) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 317 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Register Name TC1H (High) R Bit 7 6 5 4 3 2 1 Bit 0 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 W TC1H (Low) R W TC2H (High) R W TC2H (Low) R W TC3H (High) R W TC3H (Low) R W = Unimplemented or Reserved Figure 7-2. ECT Register Summary (Sheet 5 of 5) 7.3.2.1 R W Reset Timer Input Capture/Output Compare Select Register (TIOS) 7 6 5 4 3 2 1 0 IOS7 IOS6 IOS5 IOS4 IOS3 IOS2 IOS1 IOS0 0 0 0 0 0 0 0 0 Figure 7-3. Timer Input Capture/Output Compare Register (TIOS) Read or write: Anytime All bits reset to zero. Table 7-2. TIOS Field Descriptions Field 7:0 IOS[7:0] Description Input Capture or Output Compare Channel Configuration 0 The corresponding channel acts as an input capture. 1 The corresponding channel acts as an output compare. MC9S12XDP512 Data Sheet, Rev. 2.21 318 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.2 Timer Compare Force Register (CFORC) 7 6 5 4 3 2 1 0 R 0 0 0 0 0 0 0 0 W FOC7 FOC6 FOC5 FOC4 FOC3 FOC2 FOC1 FOC0 0 0 0 0 0 0 0 0 Reset Figure 7-4. Timer Compare Force Register (CFORC) Read or write: Anytime but reads will always return 0x0000 (1 state is transient). All bits reset to zero. Table 7-3. CFORC Field Descriptions Field Description 7:0 FOC[7:0] Force Output Compare Action for Channel 7:0 -- A write to this register with the corresponding data bit(s) set causes the action which is programmed for output compare "x" to occur immediately. The action taken is the same as if a successful comparison had just taken place with the TCx register except the interrupt flag does not get set. Note: A successful channel 7 output compare overrides any channel 6:0 compares. If a forced output compare on any channel occurs at the same time as the successful output compare, then the forced output compare action will take precedence and the interrupt flag will not get set. 7.3.2.3 R W Reset Output Compare 7 Mask Register (OC7M) 7 6 5 4 3 2 1 0 OC7M7 OC7M6 OC7M5 OC7M4 OC7M3 OC7M2 OC7M1 OC7M0 0 0 0 0 0 0 0 0 Figure 7-5. Output Compare 7 Mask Register (OC7M) Read or write: Anytime All bits reset to zero. Table 7-4. OC7M Field Descriptions Field Description 7:0 OC7M[7:0] Output Compare Mask Action for Channel 7:0 0 The corresponding OC7Dx bit in the output compare 7 data register will not be transferred to the timer port on a successful channel 7 output compare, even if the corresponding pin is setup for output compare. 1 The corresponding OC7Dx bit in the output compare 7 data register will be transferred to the timer port on a successful channel 7 output compare. Note: The corresponding channel must also be setup for output compare (IOSx = 1) for data to be transferred from the output compare 7 data register to the timer port. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 319 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.4 R W Reset Output Compare 7 Data Register (OC7D) 7 6 5 4 3 2 1 0 OC7D7 OC7D6 OC7D5 OC7D4 OC7D3 OC7D2 OC7D1 OC7D0 0 0 0 0 0 0 0 0 Figure 7-6. Output Compare 7 Data Register (OC7D) Read or write: Anytime All bits reset to zero. Table 7-5. OC7D Field Descriptions Field 7:0 OC7D[7:0] Description Output Compare 7 Data Bits -- A channel 7 output compare can cause bits in the output compare 7 data register to transfer to the timer port data register depending on the output compare 7 mask register. MC9S12XDP512 Data Sheet, Rev. 2.21 320 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.5 R W Reset Timer Count Register (TCNT) 15 14 13 12 11 10 9 8 TCNT15 TCNT14 TCNT13 TCNT12 TCNT11 TCNT10 TCNT9 TCNT8 0 0 0 0 0 0 0 0 Figure 7-7. Timer Count Register High (TCNT) R W Reset 7 6 5 4 3 2 1 0 TCNT7 TCNT6 TCNT5 TCNT4 TCNT3 TCNT2 TCNT1 TCNT0 0 0 0 0 0 0 0 0 Figure 7-8. Timer Count Register Low (TCNT) Read: Anytime Write: Has no meaning or effect All bits reset to zero. Table 7-6. TCNT Field Descriptions Field Description 15:0 Timer Counter Bits -- The 16-bit main timer is an up counter. A read to this register will return the current value TCNT[15:0] of the counter. Access to the counter register will take place in one clock cycle. Note: A separate read/write for high byte and low byte in test mode will give a different result than accessing them as a word. The period of the first count after a write to the TCNT registers may be a different size because the write is not synchronized with the prescaler clock. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 321 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.6 Timer System Control Register 1 (TSCR1) 7 R W Reset 6 5 4 3 TEN TSWAI TSFRZ TFFCA PRNT 0 0 0 0 0 2 1 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 7-9. Timer System Control Register 1 (TSCR1) Read or write: Anytime except PRNT bit is write once All bits reset to zero. Table 7-7. TSCR1 Field Descriptions Field Description 7 TEN Timer Enable 0 Disables the main timer, including the counter. Can be used for reducing power consumption. 1 Allows the timer to function normally. Note: If for any reason the timer is not active, there is no /64 clock for the pulse accumulator since the /64 is generated by the timer prescaler. 6 TSWAI Timer Module Stops While in Wait 0 Allows the timer module to continue running during wait. 1 Disables the timer counter, pulse accumulators and modulus down counter when the MCU is in wait mode. Timer interrupts cannot be used to get the MCU out of wait. 5 TSFRZ Timer and Modulus Counter Stop While in Freeze Mode 0 Allows the timer and modulus counter to continue running while in freeze mode. 1 Disables the timer and modulus counter whenever the MCU is in freeze mode. This is useful for emulation. The pulse accumulators do not stop in freeze mode. 4 TFFCA Timer Fast Flag Clear All 0 Allows the timer flag clearing to function normally. 1 A read from an input capture or a write to the output compare channel registers causes the corresponding channel flag, CxF, to be cleared in the TFLG1 register. Any access to the TCNT register clears the TOF flag in the TFLG2 register. Any access to the PACN3 and PACN2 registers clears the PAOVF and PAIF flags in the PAFLG register. Any access to the PACN1 and PACN0 registers clears the PBOVF flag in the PBFLG register. Any access to the MCCNT register clears the MCZF flag in the MCFLG register. This has the advantage of eliminating software overhead in a separate clear sequence. Extra care is required to avoid accidental flag clearing due to unintended accesses. Note: The flags cannot be cleared via the normal flag clearing mechanism (writing a one to the flag) when TFFCA = 1. 3 PRNT Precision Timer 0 Enables legacy timer. Only bits DLY0 and DLY1 of the DLYCT register are used for the delay selection of the delay counter. PR0, PR1, and PR2 bits of the TSCR2 register are used for timer counter prescaler selection. MCPR0 and MCPR1 bits of the MCCTL register are used for modulus down counter prescaler selection. 1 Enables precision timer. All bits in the DLYCT register are used for the delay selection, all bits of the PTPSR register are used for Precision Timer Prescaler Selection, and all bits of PTMCPSR register are used for the prescaler Precision Timer Modulus Counter Prescaler selection. MC9S12XDP512 Data Sheet, Rev. 2.21 322 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.7 R W Reset Timer Toggle On Overflow Register 1 (TTOV) 7 6 5 4 3 2 1 0 TOV7 TOV6 TOV5 TOV4 TOV3 TOV2 TOV1 TOV0 0 0 0 0 0 0 0 0 Figure 7-10. Timer Toggle On Overflow Register 1 (TTOV) Read or write: Anytime All bits reset to zero. Table 7-8. TTOV Field Descriptions Field Description 7:0 TOV[7:0] Toggle On Overflow Bits -- TOV97:0] toggles output compare pin on timer counter overflow. This feature only takes effect when in output compare mode. When set, it takes precedence over forced output compare but not channel 7 override events. 0 Toggle output compare pin on overflow feature disabled. 1 Toggle output compare pin on overflow feature enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 323 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.8 R W Reset Timer Control Register 1/Timer Control Register 2 (TCTL1/TCTL2) 7 6 5 4 3 2 1 0 OM7 OL7 OM6 OL6 OM5 OL5 OM4 OL4 0 0 0 0 0 0 0 0 Figure 7-11. Timer Control Register 1 (TCTL1) R W Reset 7 6 5 4 3 2 1 0 OM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0 0 0 0 0 0 0 0 0 Figure 7-12. Timer Control Register 2 (TCTL2) Read or write: Anytime All bits reset to zero. Table 7-9. TCTL1/TCTL2 Field Descriptions Field Description OM[7:0] 7, 5, 3, 1 OMx -- Output Mode OLx -- Output Level These eight pairs of control bits are encoded to specify the output action to be taken as a result of a successful OCx compare. When either OMx or OLx is one, the pin associated with OCx becomes an output tied to OCx. See Table 7-10. OL[7:0] 6, 4, 2, 0 Table 7-10. Compare Result Output Action OMx OLx Action 0 0 Timer disconnected from output pin logic 0 1 Toggle OCx output line 1 0 Clear OCx output line to zero 1 1 Set OCx output line to one NOTE To enable output action by OMx and OLx bits on timer port, the corresponding bit in OC7M should be cleared. MC9S12XDP512 Data Sheet, Rev. 2.21 324 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.9 R W Reset Timer Control Register 3/Timer Control Register 4 (TCTL3/TCTL4) 7 6 5 4 3 2 1 0 EDG7B EDG7A EDG6B EDG6A EDG5B EDG5A EDG4B EDG4A 0 0 0 0 0 0 0 0 Figure 7-13. Timer Control Register 3 (TCTL3) R W Reset 7 6 5 4 3 2 1 0 EDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG0A 0 0 0 0 0 0 0 0 Figure 7-14. Timer Control Register 4 (TCTL4) Read or write: Anytime All bits reset to zero. Table 7-11. TCTL3/TCTL4 Field Descriptions Field Description EDG[7:0]B 7, 5, 3, 1 Input Capture Edge Control -- These eight pairs of control bits configure the input capture edge detector circuits for each input capture channel. The four pairs of control bits in TCTL4 also configure the input capture edge control for the four 8-bit pulse accumulators PAC0-PAC3.EDG0B and EDG0A in TCTL4 also determine the active edge for the 16-bit pulse accumulator PACB. See Table 7-12. EDG[7:0]A 6, 4, 2, 0 Table 7-12. Edge Detector Circuit Configuration EDGxB EDGxA Configuration 0 0 Capture disabled 0 1 Capture on rising edges only 1 0 Capture on falling edges only 1 1 Capture on any edge (rising or falling) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 325 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.10 R W Reset Timer Interrupt Enable Register (TIE) 7 6 5 4 3 2 1 0 C7I C6I C5I C4I C3I C2I C1I C0I 0 0 0 0 0 0 0 0 Figure 7-15. Timer Interrupt Enable Register (TIE) Read or write: Anytime All bits reset to zero. The bits C7I-C0I correspond bit-for-bit with the flags in the TFLG1 status register. Table 7-13. TIE Field Descriptions Field 7:0 C[7:0]I Description Input Capture/Output Compare "x" Interrupt Enable 0 The corresponding flag is disabled from causing a hardware interrupt. 1 The corresponding flag is enabled to cause an interrupt. MC9S12XDP512 Data Sheet, Rev. 2.21 326 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.11 Timer System Control Register 2 (TSCR2) 7 R W Reset TOI 0 6 5 4 0 0 0 0 0 0 3 2 1 0 TCRE PR2 PR1 PR0 0 0 0 0 = Unimplemented or Reserved Figure 7-16. Timer System Control Register 2 (TSCR2) Read or write: Anytime All bits reset to zero. Table 7-14. TSCR2 Field Descriptions Field 7 TOI Description Timer Overflow Interrupt Enable 0 Timer overflow interrupt disabled. 1 Hardware interrupt requested when TOF flag set. 3 TCRE Timer Counter Reset Enable -- This bit allows the timer counter to be reset by a successful channel 7 output compare. This mode of operation is similar to an up-counting modulus counter. 0 Counter reset disabled and counter free runs. 1 Counter reset by a successful output compare on channel 7. Note: If register TC7 = 0x0000 and TCRE = 1, then the TCNT register will stay at 0x0000 continuously. If register TC7 = 0xFFFF and TCRE = 1, the TOF flag will never be set when TCNT is reset from 0xFFFF to 0x0000. 2:0 PR[2:0] Timer Prescaler Select -- These three bits specify the division rate of the main Timer prescaler when the PRNT bit of register TSCR1 is set to 0. The newly selected prescale factor will not take effect until the next synchronized edge where all prescale counter stages equal zero. See Table 7-15. Table 7-15. Prescaler Selection PR2 PR1 PR0 Prescale Factor 0 0 0 1 0 0 1 2 0 1 0 4 0 1 1 8 1 0 0 16 1 0 1 32 1 1 0 64 1 1 1 128 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 327 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.12 R W Reset Main Timer Interrupt Flag 1 (TFLG1) 7 6 5 4 3 2 1 0 C7F C6F C5F C4F C3F C2F C1F C0F 0 0 0 0 0 0 0 0 Figure 7-17. Main Timer Interrupt Flag 1 (TFLG1) Read: Anytime Write used in the flag clearing mechanism. Writing a one to the flag clears the flag. Writing a zero will not affect the current status of the bit. NOTE When TFFCA = 1, the flags cannot be cleared via the normal flag clearing mechanism (writing a one to the flag). Reference Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)". All bits reset to zero. TFLG1 indicates when interrupt conditions have occurred. The flags can be cleared via the normal flag clearing mechanism (writing a one to the flag) or via the fast flag clearing mechanism (reference TFFCA bit in Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)"). Use of the TFMOD bit in the ICSYS register in conjunction with the use of the ICOVW register allows a timer interrupt to be generated after capturing two values in the capture and holding registers, instead of generating an interrupt for every capture. Table 7-16. TFLG1 Field Descriptions Field Description 7:0 C[7:0]F Input Capture/Output Compare Channel "x" Flag -- A CxF flag is set when a corresponding input capture or output compare is detected. C0F can also be set by 16-bit Pulse Accumulator B (PACB). C3F-C0F can also be set by 8-bit pulse accumulators PAC3-PAC0. If the delay counter is enabled, the CxF flag will not be set until after the delay. MC9S12XDP512 Data Sheet, Rev. 2.21 328 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.13 Main Timer Interrupt Flag 2 (TFLG2) 7 R W Reset TOF 0 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 7-18. Main Timer Interrupt Flag 2 (TFLG2) Read: Anytime Write used in the flag clearing mechanism. Writing a one to the flag clears the flag. Writing a zero will not affect the current status of the bit. NOTE When TFFCA = 1, the flag cannot be cleared via the normal flag clearing mechanism (writing a one to the flag). Reference Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)". All bits reset to zero. TFLG2 indicates when interrupt conditions have occurred. The flag can be cleared via the normal flag clearing mechanism (writing a one to the flag) or via the fast flag clearing mechanism (Reference TFFCA bit in Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)"). Table 7-17. TFLG2 Field Descriptions Field 7 TOF Description Timer Overflow Flag -- Set when 16-bit free-running timer overflows from 0xFFFF to 0x0000. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 329 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.14 R W Reset Timer Input Capture/Output Compare Registers 0-7 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-19. Timer Input Capture/Output Compare Register 0 High (TC0) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-20. Timer Input Capture/Output Compare Register 0 Low (TC0) R W Reset 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-21. Timer Input Capture/Output Compare Register 1 High (TC1) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-22. Timer Input Capture/Output Compare Register 1 Low (TC1) R W Reset 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-23. Timer Input Capture/Output Compare Register 2 High (TC2) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-24. Timer Input Capture/Output Compare Register 2 Low (TC2) R W Reset 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-25. Timer Input Capture/Output Compare Register 3 High (TC3) MC9S12XDP512 Data Sheet, Rev. 2.21 330 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-26. Timer Input Capture/Output Compare Register 3 Low (TC3) R W Reset 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-27. Timer Input Capture/Output Compare Register 4 High (TC4) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-28. Timer Input Capture/Output Compare Register 4 Low (TC4) R W Reset 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-29. Timer Input Capture/Output Compare Register 5 High (TC5) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-30. Timer Input Capture/Output Compare Register 5 Low (TC5) R W Reset 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-31. Timer Input Capture/Output Compare Register 6 High (TC6) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-32. Timer Input Capture/Output Compare Register 6 Low (TC6) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 331 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) R W Reset 15 14 13 12 11 10 9 8 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 7-33. Timer Input Capture/Output Compare Register 7 High (TC7) R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 7-34. Timer Input Capture/Output Compare Register 7 Low (TC7) Read: Anytime Write anytime for output compare function. Writes to these registers have no meaning or effect during input capture. All bits reset to zero. Depending on the TIOS bit for the corresponding channel, these registers are used to latch the value of the free-running counter when a defined transition is sensed by the corresponding input capture edge detector or to trigger an output action for output compare. 7.3.2.15 16-Bit Pulse Accumulator A Control Register (PACTL) 7 R 0 W Reset 0 6 5 4 3 2 1 0 PAEN PAMOD PEDGE CLK1 CLK0 PAOVI PAI 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 7-35. 16-Bit Pulse Accumulator Control Register (PACTL) Read: Anytime Write: Anytime All bits reset to zero. Table 7-18. PACTL Field Descriptions Field Description 6 PAEN Pulse Accumulator A System Enable -- PAEN is independent from TEN. With timer disabled, the pulse accumulator can still function unless pulse accumulator is disabled. 0 16-Bit Pulse Accumulator A system disabled. 8-bit PAC3 and PAC2 can be enabled when their related enable bits in ICPAR are set. Pulse Accumulator Input Edge Flag (PAIF) function is disabled. 1 16-Bit Pulse Accumulator A system enabled. The two 8-bit pulse accumulators PAC3 and PAC2 are cascaded to form the PACA 16-bit pulse accumulator. When PACA in enabled, the PACN3 and PACN2 registers contents are respectively the high and low byte of the PACA. PA3EN and PA2EN control bits in ICPAR have no effect. Pulse Accumulator Input Edge Flag (PAIF) function is enabled. The PACA shares the input pin with IC7. MC9S12XDP512 Data Sheet, Rev. 2.21 332 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Table 7-18. PACTL Field Descriptions (continued) Field Description 5 PAMOD Pulse Accumulator Mode -- This bit is active only when the Pulse Accumulator A is enabled (PAEN = 1). 0 Event counter mode 1 Gated time accumulation mode 4 PEDGE Pulse Accumulator Edge Control -- This bit is active only when the Pulse Accumulator A is enabled (PAEN = 1). Refer to Table 7-19. For PAMOD bit = 0 (event counter mode). 0 Falling edges on PT7 pin cause the count to be incremented 1 Rising edges on PT7 pin cause the count to be incremented For PAMOD bit = 1 (gated time accumulation mode). 0 PT7 input pin high enables bus clock divided by 64 to Pulse Accumulator and the trailing falling edge on PT7 sets the PAIF flag. 1 PT7 input pin low enables bus clock divided by 64 to Pulse Accumulator and the trailing rising edge on PT7 sets the PAIF flag. If the timer is not active (TEN = 0 in TSCR1), there is no divide-by-64 since the /64 clock is generated by the timer prescaler. 3:2 CLK[1:0] 2 PAOVI 0 PAI Clock Select Bits -- For the description of PACLK please refer to Figure 7-70. If the pulse accumulator is disabled (PAEN = 0), the prescaler clock from the timer is always used as an input clock to the timer counter. The change from one selected clock to the other happens immediately after these bits are written. Refer to Table 7-20. Pulse Accumulator A Overflow Interrupt Enable 0 Interrupt inhibited 1 Interrupt requested if PAOVF is set Pulse Accumulator Input Interrupt Enable 0 Interrupt inhibited 1 Interrupt requested if PAIF is set . Table 7-19. Pin Action PAMOD PEDGE Pin Action 0 0 Falling edge 0 1 Rising edge 1 0 Divide by 64 clock enabled with pin high level 1 1 Divide by 64 clock enabled with pin low level Table 7-20. Clock Selection CLK1 CLK0 Clock Source 0 0 Use timer prescaler clock as timer counter clock 0 1 Use PACLK as input to timer counter clock 1 0 Use PACLK/256 as timer counter clock frequency 1 1 Use PACLK/65536 as timer counter clock frequency MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 333 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.16 R Pulse Accumulator A Flag Register (PAFLG) 7 6 5 4 3 2 0 0 0 0 0 0 0 0 0 0 0 0 W Reset 1 0 PAOVF PAIF 0 0 = Unimplemented or Reserved Figure 7-36. Pulse Accumulator A Flag Register (PAFLG) Read: Anytime Write used in the flag clearing mechanism. Writing a one to the flag clears the flag. Writing a zero will not affect the current status of the bit. NOTE When TFFCA = 1, the flags cannot be cleared via the normal flag clearing mechanism (writing a one to the flag). Reference Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)". All bits reset to zero. PAFLG indicates when interrupt conditions have occurred. The flags can be cleared via the normal flag clearing mechanism (writing a one to the flag) or via the fast flag clearing mechanism (Reference TFFCA bit in Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)"). Table 7-21. PAFLG Field Descriptions Field Description 1 PAOVF Pulse Accumulator A Overflow Flag -- Set when the 16-bit pulse accumulator A overflows from 0xFFFF to 0x0000, or when 8-bit pulse accumulator 3 (PAC3) overflows from 0x00FF to 0x0000. When PACMX = 1, PAOVF bit can also be set if 8-bit pulse accumulator 3 (PAC3) reaches 0x00FF followed by an active edge on PT3. 0 PAIF Pulse Accumulator Input edge Flag -- Set when the selected edge is detected at the PT7 input pin. In event mode the event edge triggers PAIF and in gated time accumulation mode the trailing edge of the gate signal at the PT7 input pin triggers PAIF. 7.3.2.17 Pulse Accumulators Count Registers (PACN3 and PACN2) 7 R W Reset 6 5 4 3 2 PACNT7(15) PACNT6(14) PACNT5(13) PACNT4(12) PACNT3(11) PACNT2(10) 0 0 0 0 0 0 1 0 PACNT1(9) PACNT0(8) 0 0 Figure 7-37. Pulse Accumulators Count Register 3 (PACN3) MC9S12XDP512 Data Sheet, Rev. 2.21 334 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) R W Reset 7 6 5 4 3 2 1 0 PACNT7 PACNT6 PACNT5 PACNT4 PACNT3 PACNT2 PACNT1 PACNT0 0 0 0 0 0 0 0 0 Figure 7-38. Pulse Accumulators Count Register 2 (PACN2) Read: Anytime Write: Anytime All bits reset to zero. The two 8-bit pulse accumulators PAC3 and PAC2 are cascaded to form the PACA 16-bit pulse accumulator. When PACA in enabled (PAEN = 1 in PACTL), the PACN3 and PACN2 registers contents are respectively the high and low byte of the PACA. When PACN3 overflows from 0x00FF to 0x0000, the interrupt flag PAOVF in PAFLG is set. Full count register access will take place in one clock cycle. NOTE A separate read/write for high byte and low byte will give a different result than accessing them as a word. When clocking pulse and write to the registers occurs simultaneously, write takes priority and the register is not incremented. 7.3.2.18 Pulse Accumulators Count Registers (PACN1 and PACN0) 7 R W Reset 6 5 4 3 2 PACNT7(15) PACNT6(14) PACNT5(13) PACNT4(12) PACNT3(11) PACNT2(10) 0 0 0 0 0 0 1 0 PACNT1(9) PACNT0(8) 0 0 Figure 7-39. Pulse Accumulators Count Register 1 (PACN1) R W Reset 7 6 5 4 3 2 1 0 PACNT7 PACNT6 PACNT5 PACNT4 PACNT3 PACNT2 PACNT1 PACNT0 0 0 0 0 0 0 0 0 Figure 7-40. Pulse Accumulators Count Register 0 (PACN0) Read: Anytime Write: Anytime All bits reset to zero. The two 8-bit pulse accumulators PAC1 and PAC0 are cascaded to form the PACB 16-bit pulse accumulator. When PACB in enabled, (PBEN = 1 in PBCTL) the PACN1 and PACN0 registers contents are respectively the high and low byte of the PACB. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 335 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) When PACN1 overflows from 0x00FF to 0x0000, the interrupt flag PBOVF in PBFLG is set. Full count register access will take place in one clock cycle. NOTE A separate read/write for high byte and low byte will give a different result than accessing them as a word. When clocking pulse and write to the registers occurs simultaneously, write takes priority and the register is not incremented. MC9S12XDP512 Data Sheet, Rev. 2.21 336 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.19 16-Bit Modulus Down-Counter Control Register (MCCTL) 7 R W Reset 6 5 MCZI MODMC RDMCL 0 0 0 4 3 0 0 ICLAT FLMC 0 0 2 1 0 MCEN MCPR1 MCPR0 0 0 0 Figure 7-41. 16-Bit Modulus Down-Counter Control Register (MCCTL) Read: Anytime Write: Anytime All bits reset to zero. Table 7-22. MCCTL Field Descriptions Field 7 MCZI Description Modulus Counter Underflow Interrupt Enable 0 Modulus counter interrupt is disabled. 1 Modulus counter interrupt is enabled. 6 MODMC Modulus Mode Enable 0 The modulus counter counts down from the value written to it and will stop at 0x0000. 1 Modulus mode is enabled. When the modulus counter reaches 0x0000, the counter is loaded with the latest value written to the modulus count register. Note: For proper operation, the MCEN bit should be cleared before modifying the MODMC bit in order to reset the modulus counter to 0xFFFF. 5 RDMCL Read Modulus Down-Counter Load 0 Reads of the modulus count register (MCCNT) will return the present value of the count register. 1 Reads of the modulus count register (MCCNT) will return the contents of the load register. 4 ICLAT Input Capture Force Latch Action -- When input capture latch mode is enabled (LATQ and BUFEN bit in ICSYS are set), a write one to this bit immediately forces the contents of the input capture registers TC0 to TC3 and their corresponding 8-bit pulse accumulators to be latched into the associated holding registers. The pulse accumulators will be automatically cleared when the latch action occurs. Writing zero to this bit has no effect. Read of this bit will always return zero. 3 FLMC Force Load Register into the Modulus Counter Count Register -- This bit is active only when the modulus down-counter is enabled (MCEN = 1). A write one into this bit loads the load register into the modulus counter count register (MCCNT). This also resets the modulus counter prescaler. Write zero to this bit has no effect. Read of this bit will return always zero. 2 MCEN 1:0 MCPR[1:0] Modulus Down-Counter Enable 0 Modulus counter disabled. The modulus counter (MCCNT) is preset to 0xFFFF. This will prevent an early interrupt flag when the modulus down-counter is enabled. 1 Modulus counter is enabled. Modulus Counter Prescaler Select -- These two bits specify the division rate of the modulus counter prescaler when PRNT of TSCR1 is set to 0. The newly selected prescaler division rate will not be effective until a load of the load register into the modulus counter count register occurs. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 337 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Table 7-23. Modulus Counter Prescaler Select 7.3.2.20 W Reset MCPR0 Prescaler Division 0 0 1 0 1 4 1 0 8 1 1 16 16-Bit Modulus Down-Counter FLAG Register (MCFLG) 7 R MCPR1 MCZF 0 6 5 4 3 2 1 0 0 0 0 POLF3 POLF2 POLF1 POLF0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 7-42. 16-Bit Modulus Down-Counter FLAG Register (MCFLG) Read: Anytime Write only used in the flag clearing mechanism for bit 7. Writing a one to bit 7 clears the flag. Writing a zero will not affect the current status of the bit. NOTE When TFFCA = 1, the flag cannot be cleared via the normal flag clearing mechanism (writing a one to the flag). Reference Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)". All bits reset to zero. Table 7-24. MCFLG Field Descriptions Field 7 MCZF 3:0 POLF[3:0] Description Modulus Counter Underflow Flag -- The flag is set when the modulus down-counter reaches 0x0000. The flag indicates when interrupt conditions have occurred. The flag can be cleared via the normal flag clearing mechanism (writing a one to the flag) or via the fast flag clearing mechanism (Reference TFFCA bit in Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)"). First Input Capture Polarity Status -- These are read only bits. Writes to these bits have no effect. Each status bit gives the polarity of the first edge which has caused an input capture to occur after capture latch has been read. Each POLFx corresponds to a timer PORTx input. 0 The first input capture has been caused by a falling edge. 1 The first input capture has been caused by a rising edge. MC9S12XDP512 Data Sheet, Rev. 2.21 338 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.21 R ICPAR -- Input Control Pulse Accumulators Register (ICPAR) 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 PA3EN PA2EN PA1EN PA0EN 0 0 0 0 = Unimplemented or Reserved Figure 7-43. Input Control Pulse Accumulators Register (ICPAR) Read: Anytime Write: Anytime. All bits reset to zero. The 8-bit pulse accumulators PAC3 and PAC2 can be enabled only if PAEN in PACTL is cleared. If PAEN is set, PA3EN and PA2EN have no effect. The 8-bit pulse accumulators PAC1 and PAC0 can be enabled only if PBEN in PBCTL is cleared. If PBEN is set, PA1EN and PA0EN have no effect. Table 7-25. ICPAR Field Descriptions Field 3:0 PA[3:0]EN Description 8-Bit Pulse Accumulator `x' Enable 0 8-Bit Pulse Accumulator is disabled. 1 8-Bit Pulse Accumulator is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 339 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.22 R W Reset Delay Counter Control Register (DLYCT) 7 6 5 4 3 2 1 0 DLY7 DLY6 DLY5 DLY4 DLY3 DLY2 DLY1 DLY0 0 0 0 0 0 0 0 0 Figure 7-44. Delay Counter Control Register (DLYCT) Read: Anytime Write: Anytime All bits reset to zero. Table 7-26. DLYCT Field Descriptions Field 7:0 DLY[7:0] Description Delay Counter Select -- When the PRNT bit of TSCR1 register is set to 0, only bits DLY0, DLY1 are used to calculate the delay.Table 7-27 shows the delay settings in this case. When the PRNT bit of TSCR1 register is set to 1, all bits are used to set a more precise delay. Table 7-28 shows the delay settings in this case. After detection of a valid edge on an input capture pin, the delay counter counts the pre-selected number of [(dly_cnt + 1)*4]bus clock cycles, then it will generate a pulse on its output if the level of input signal, after the preset delay, is the opposite of the level before the transition.This will avoid reaction to narrow input pulses. Delay between two active edges of the input signal period should be longer than the selected counter delay. Note: It is recommended to not write to this register while the timer is enabled, that is when TEN is set in register TSCR1. Table 7-27. Delay Counter Select when PRNT = 0 DLY1 DLY0 Delay 0 0 1 1 0 1 0 1 Disabled 256 bus clock cycles 512 bus clock cycles 1024 bus clock cycles Table 7-28. Delay Counter Select Examples when PRNT = 1 DLY7 DLY6 DLY5 DLY4 DLY3 DLY2 DLY1 DLY0 Delay 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 0 0 1 1 0 0 1 1 1 1 1 1 1 0 1 0 1 0 1 0 1 1 1 1 1 1 Disabled (bypassed) 8 bus clock cycles 12 bus clock cycles 16 bus clock cycles 20 bus clock cycles 24 bus clock cycles 28 bus clock cycles 32 bus clock cycles 64 bus clock cycles 128 bus clock cycles 256 bus clock cycles 512 bus clock cycles 1024 bus clock cycles MC9S12XDP512 Data Sheet, Rev. 2.21 340 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.23 R W Reset Input Control Overwrite Register (ICOVW) 7 6 5 4 3 2 1 0 NOVW7 NOVW6 NOVW5 NOVW4 NOVW3 NOVW2 NOVW1 NOVW0 0 0 0 0 0 0 0 0 Figure 7-45. Input Control Overwrite Register (ICOVW) Read: Anytime Write: Anytime All bits reset to zero. Table 7-29. ICOVW Field Descriptions Field Description 7:0 NOVW[7:0] No Input Capture Overwrite 0 The contents of the related capture register or holding register can be overwritten when a new input capture or latch occurs. 1 The related capture register or holding register cannot be written by an event unless they are empty (see Section 7.4.1.1, "IC Channels"). This will prevent the captured value being overwritten until it is read or latched in the holding register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 341 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.24 R W Reset Input Control System Control Register (ICSYS) 7 6 5 4 3 2 1 0 SH37 SH26 SH15 SH04 TFMOD PACMX BUFEN LATQ 0 0 0 0 0 0 0 0 Figure 7-46. Input Control System Register (ICSYS) Read: Anytime Write: Once in normal modes All bits reset to zero. Table 7-30. ICSYS Field Descriptions Field Description 7:4 SHxy Share Input action of Input Capture Channels x and y 0 Normal operation 1 The channel input `x' causes the same action on the channel `y'. The port pin `x' and the corresponding edge detector is used to be active on the channel `y'. 3 TFMOD Timer Flag Setting Mode -- Use of the TFMOD bit in conjunction with the use of the ICOVW register allows a timer interrupt to be generated after capturing two values in the capture and holding registers instead of generating an interrupt for every capture. By setting TFMOD in queue mode, when NOVWx bit is set and the corresponding capture and holding registers are emptied, an input capture event will first update the related input capture register with the main timer contents. At the next event, the TCx data is transferred to the TCxH register, the TCx is updated and the CxF interrupt flag is set. In all other input capture cases the interrupt flag is set by a valid external event on PTx. 0 The timer flags C3F-C0F in TFLG1 are set when a valid input capture transition on the corresponding port pin occurs. 1 If in queue mode (BUFEN = 1 and LATQ = 0), the timer flags C3F-C0F in TFLG1 are set only when a latch on the corresponding holding register occurs. If the queue mode is not engaged, the timer flags C3F-C0F are set the same way as for TFMOD = 0. 2 PACMX 8-Bit Pulse Accumulators Maximum Count 0 Normal operation. When the 8-bit pulse accumulator has reached the value 0x00FF, with the next active edge, it will be incremented to 0x0000. 1 When the 8-bit pulse accumulator has reached the value 0x00FF, it will not be incremented further. The value 0x00FF indicates a count of 255 or more. 1 BUFFEN IC Buffer Enable 0 Input capture and pulse accumulator holding registers are disabled. 1 Input capture and pulse accumulator holding registers are enabled. The latching mode is defined by LATQ control bit. MC9S12XDP512 Data Sheet, Rev. 2.21 342 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Table 7-30. ICSYS Field Descriptions (continued) Field Description 0 LATQ Input Control Latch or Queue Mode Enable -- The BUFEN control bit should be set in order to enable the IC and pulse accumulators holding registers. Otherwise LATQ latching modes are disabled. Write one into ICLAT bit in MCCTL, when LATQ and BUFEN are set will produce latching of input capture and pulse accumulators registers into their holding registers. 0 Queue mode of Input Capture is enabled. The main timer value is memorized in the IC register by a valid input pin transition. With a new occurrence of a capture, the value of the IC register will be transferred to its holding register and the IC register memorizes the new timer value. 1 Latch mode is enabled. Latching function occurs when modulus down-counter reaches zero or a zero is written into the count register MCCNT (see Section 7.4.1.1.2, "Buffered IC Channels"). With a latching event the contents of IC registers and 8-bit pulse accumulators are transferred to their holding registers. 8-bit pulse accumulators are cleared. 7.3.2.25 R W Reset Precision Timer Prescaler Select Register (PTPSR) 7 6 5 4 3 2 1 0 PTPS7 PTPS6 PTPS5 PTPS4 PTPS3 PTPS2 PTPS1 PTPS0 0 0 0 0 0 0 0 0 Figure 7-47. Precision Timer Prescaler Select Register (PTPSR) Read: Anytime Write: Anytime All bits reset to zero. Table 7-31. PTPSR Field Descriptions Field Description 7:0 PTPS[7:0] Precision Timer Prescaler Select Bits -- These eight bits specify the division rate of the main Timer prescaler. These are effective only when the PRNT bit of TSCR1 is set to 1. Table 7-32 shows some selection examples in this case. The newly selected prescale factor will not take effect until the next synchronized edge where all prescale counter stages equal zero. Table 7-32. Precision Timer Prescaler Selection Examples when PRNT = 1 PTPS7 PTPS6 PTPS5 PTPS4 PTPS3 PTPS2 PTPS1 PTPS0 Prescale Factor 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 2 0 0 0 0 0 0 1 0 3 0 0 0 0 0 0 1 1 4 0 0 0 0 0 1 0 0 5 0 0 0 0 0 1 0 1 6 0 0 0 0 0 1 1 0 7 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 343 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Table 7-32. Precision Timer Prescaler Selection Examples when PRNT = 1 PTPS7 PTPS6 PTPS5 PTPS4 PTPS3 PTPS2 PTPS1 PTPS0 Prescale Factor 0 0 0 0 0 1 1 1 8 0 0 0 0 1 1 1 1 16 0 0 0 1 1 1 1 1 32 0 0 1 1 1 1 1 1 64 0 1 1 1 1 1 1 1 128 1 1 1 1 1 1 1 1 256 7.3.2.26 R W Reset Precision Timer Modulus Counter Prescaler Select Register (PTMCPSR) 7 6 5 4 3 2 1 0 PTMPS7 PTMPS6 PTMPS5 PTMPS4 PTMPS3 PTMPS2 PTMPS1 PTMPS0 0 0 0 0 0 0 0 0 Figure 7-48. Precision Timer Modulus Counter Prescaler Select Register (PTMCPSR) Read: Anytime Write: Anytime All bits reset to zero. Table 7-33. PTMCPSR Field Descriptions Field Description 7:0 Precision Timer Modulus Counter Prescaler Select Bits -- These eight bits specify the division rate of the PTMPS[7:0] modulus counter prescaler. These are effective only when the PRNT bit of TSCR1 is set to 1. Table 7-34 shows some possible division rates. The newly selected prescaler division rate will not be effective until a load of the load register into the modulus counter count register occurs. Table 7-34. Precision Timer Modulus Counter Prescaler Select Examples when PRNT = 1 PTMPS7 PTMPS6 PTMPS5 PTMPS4 PTMPS3 PTMPS2 PTMPS1 PTMPS0 Prescaler Division Rate 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 2 0 0 0 0 0 0 1 0 3 0 0 0 0 0 0 1 1 4 0 0 0 0 0 1 0 0 5 0 0 0 0 0 1 0 1 6 0 0 0 0 0 1 1 0 7 MC9S12XDP512 Data Sheet, Rev. 2.21 344 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Table 7-34. Precision Timer Modulus Counter Prescaler Select Examples when PRNT = 1 (continued) PTMPS7 PTMPS6 PTMPS5 PTMPS4 PTMPS3 PTMPS2 PTMPS1 PTMPS0 Prescaler Division Rate 0 0 0 0 0 1 1 1 8 0 0 0 0 1 1 1 1 16 0 0 0 1 1 1 1 1 32 0 0 1 1 1 1 1 1 64 0 1 1 1 1 1 1 1 128 1 1 1 1 1 1 1 1 256 7.3.2.27 16-Bit Pulse Accumulator B Control Register (PBCTL) 7 R 6 0 PBEN W Reset 0 0 5 4 3 2 0 0 0 0 0 0 0 0 1 PBOVI 0 0 0 0 = Unimplemented or Reserved Figure 7-49. 16-Bit Pulse Accumulator B Control Register (PBCTL) Read: Anytime Write: Anytime All bits reset to zero. Table 7-35. PBCTL Field Descriptions Field Description 6 PBEN Pulse Accumulator B System Enable -- PBEN is independent from TEN. With timer disabled, the pulse accumulator can still function unless pulse accumulator is disabled. 0 16-bit pulse accumulator system disabled. 8-bit PAC1 and PAC0 can be enabled when their related enable bits in ICPAR are set. 1 Pulse accumulator B system enabled. The two 8-bit pulse accumulators PAC1 and PAC0 are cascaded to form the PACB 16-bit pulse accumulator B. When PACB is enabled, the PACN1 and PACN0 registers contents are respectively the high and low byte of the PACB. PA1EN and PA0EN control bits in ICPAR have no effect. The PACB shares the input pin with IC0. 1 PBOVI Pulse Accumulator B Overflow Interrupt Enable 0 Interrupt inhibited 1 Interrupt requested if PBOVF is set MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 345 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.28 R Pulse Accumulator B Flag Register (PBFLG) 7 6 5 4 3 2 0 0 0 0 0 0 0 0 0 0 0 0 W Reset 1 PBOVF 0 0 0 0 = Unimplemented or Reserved Figure 7-50. Pulse Accumulator B Flag Register (PBFLG) Read: Anytime Write used in the flag clearing mechanism. Writing a one to the flag clears the flag. Writing a zero will not affect the current status of the bit. NOTE When TFFCA = 1, the flag cannot be cleared via the normal flag clearing mechanism (writing a one to the flag). Reference Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)". All bits reset to zero. PBFLG indicates when interrupt conditions have occurred. The flag can be cleared via the normal flag clearing mechanism (writing a one to the flag) or via the fast flag clearing mechanism (Reference TFFCA bit in Section 7.3.2.6, "Timer System Control Register 1 (TSCR1)"). Table 7-36. PBFLG Field Descriptions Field 1 PBOVF Description Pulse Accumulator B Overflow Flag -- This bit is set when the 16-bit pulse accumulator B overflows from 0xFFFF to 0x0000, or when 8-bit pulse accumulator 1 (PAC1) overflows from 0x00FF to 0x0000. When PACMX = 1, PBOVF bit can also be set if 8-bit pulse accumulator 1 (PAC1) reaches 0x00FF and an active edge follows on PT1. MC9S12XDP512 Data Sheet, Rev. 2.21 346 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.29 R 8-Bit Pulse Accumulators Holding Registers (PA3H-PA0H) 7 6 5 4 3 2 1 0 PA3H7 PA3H6 PA3H5 PA3H4 PA3H3 PA3H2 PA3H1 PA3H0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 7-51. 8-Bit Pulse Accumulators Holding Register 3 (PA3H) R 7 6 5 4 3 2 1 0 PA2H7 PA2H6 PA2H5 PA2H4 PA2H3 PA2H2 PA2H1 PA2H0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 7-52. 8-Bit Pulse Accumulators Holding Register 2 (PA2H) R 7 6 5 4 3 2 1 0 PA1H7 PA1H6 PA1H5 PA1H4 PA1H3 PA1H2 PA1H1 PA1H0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 7-53. 8-Bit Pulse Accumulators Holding Register 1 (PA1H) R 7 6 5 4 3 2 1 0 PA0H7 PA0H6 PA0H5 PA0H4 PA0H3 PA0H2 PA0H1 PA0H0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 7-54. 8-Bit Pulse Accumulators Holding Register 0 (PA0H) Read: Anytime. Write: Has no effect. All bits reset to zero. These registers are used to latch the value of the corresponding pulse accumulator when the related bits in register ICPAR are enabled (see Section 7.4.1.3, "Pulse Accumulators"). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 347 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.30 R W Reset Modulus Down-Counter Count Register (MCCNT) 15 14 13 12 11 10 9 8 MCCNT15 MCCNT14 MCCNT13 MCCNT12 MCCNT11 MCCNT10 MCCNT9 MCCNT8 1 1 1 1 1 1 1 1 Figure 7-55. Modulus Down-Counter Count Register High (MCCNT) R W Reset 7 6 5 4 3 2 1 0 MCCNT7 MCCNT6 MCCNT5 MCCNT4 MCCNT3 MCCNT2 MCCNT1 MCCNT9 1 1 1 1 1 1 1 1 Figure 7-56. Modulus Down-Counter Count Register Low (MCCNT) Read: Anytime Write: Anytime. All bits reset to one. A full access for the counter register will take place in one clock cycle. NOTE A separate read/write for high byte and low byte will give different results than accessing them as a word. If the RDMCL bit in MCCTL register is cleared, reads of the MCCNT register will return the present value of the count register. If the RDMCL bit is set, reads of the MCCNT will return the contents of the load register. If a 0x0000 is written into MCCNT when LATQ and BUFEN in ICSYS register are set, the input capture and pulse accumulator registers will be latched. With a 0x0000 write to the MCCNT, the modulus counter will stay at zero and does not set the MCZF flag in MCFLG register. If the modulus down counter is enabled (MCEN = 1) and modulus mode is enabled (MODMC = 1), a write to MCCNT will update the load register with the value written to it. The count register will not be updated with the new value until the next counter underflow. If modulus mode is not enabled (MODMC = 0), a write to MCCNT will clear the modulus prescaler and will immediately update the counter register with the value written to it and down-counts to 0x0000 and stops. The FLMC bit in MCCTL can be used to immediately update the count register with the new value if an immediate load is desired. MC9S12XDP512 Data Sheet, Rev. 2.21 348 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.3.2.31 R Timer Input Capture Holding Registers 0-3 (TCxH) 15 14 13 12 11 10 9 8 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 7-57. Timer Input Capture Holding Register 0 High (TC0H) R 7 6 5 4 3 2 1 0 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 7-58. Timer Input Capture Holding Register 0 Low (TC0H) R 15 14 13 12 11 10 9 8 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 7-59. Timer Input Capture Holding Register 1 High (TC1H) R 7 6 5 4 3 2 1 0 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 7-60. Timer Input Capture Holding Register 1 Low (TC1H) R 15 14 13 12 11 10 9 8 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 7-61. Timer Input Capture Holding Register 2 High (TC2H) R 7 6 5 4 3 2 1 0 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 7-62. Timer Input Capture Holding Register 2 Low (TC2H) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 349 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) R 15 14 13 12 11 10 9 8 TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 7-63. Timer Input Capture Holding Register 3 High (TC3H) R 7 6 5 4 3 2 1 0 TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 7-64. Timer Input Capture Holding Register 3 Low (TC3H) Read: Anytime Write: Has no effect. All bits reset to zero. These registers are used to latch the value of the input capture registers TC0-TC3. The corresponding IOSx bits in TIOS should be cleared (see Section 7.4.1.1, "IC Channels"). 7.4 Functional Description This section provides a complete functional description of the ECT block, detailing the operation of the design from the end user perspective in a number of subsections. MC9S12XDP512 Data Sheet, Rev. 2.21 350 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Bus Clock / 1, 4, 8, 16 Bus Clock Timer Prescaler 16-Bit Load Register 16-Bit Modulus Down Counter Modulus Prescaler 0 P0 Comparator Pin Logic Delay Counter EDG0 TC0 Capture/Compare Reg. PAC0 TC0H Hold Reg. PA0H Hold Reg. 0 P1 Pin Logic Delay Counter EDG1 TC1 Capture/Compare Reg. PAC1 TC1H Hold Reg. PA1H Hold Reg. Pin Logic Delay Counter EDG2 TC2 Capture/Compare Reg. PAC2 TC2H Hold Reg. PA2H Hold Reg. Pin Logic Pin Logic RESET Comparator Delay Counter EDG3 TC3 Capture/Compare Reg. PAC3 TC3H Hold Reg. PA3H Hold Reg. LATCH P4 RESET Comparator 0 P3 RESET Comparator 0 P2 RESET Underflow 16-Bit Free-Running 16 BITMain MAIN TIMER Timer / 1, 2, ..., 128 Comparator EDG4 EDG0 TC4 Capture/Compare Reg. MUX ICLAT, LATQ, BUFEN (Force Latch) SH04 P5 Pin Logic Comparator EDG5 EDG1 TC5 Capture/Compare Reg. MUX Write 0x0000 to Modulus Counter SH15 P6 Pin Logic Comparator EDG6 EDG2 LATQ (MDC Latch Enable) TC6 Capture/Compare Reg. MUX SH26 P7 Pin Logic Comparator EDG7 EDG3 TC7 Capture/Compare Reg. MUX SH37 Figure 7-65. Detailed Timer Block Diagram in Latch Mode when PRNT = 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 351 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Bus Clock / 1, 2,3, ..., 256 Bus Clock Timer Prescaler 16-Bit Load Register 16-Bit Modulus Down Counter Modulus Prescaler 0 P0 RESET Underflow 16-Bit Free-Running 16 BITMain MAINTimer TIMER / 1, 2,3, ..., 256 Comparator Pin Logic Delay Counter EDG0 TC0 Capture/Compare Reg. PAC0 TC0H Hold Reg. PA0H Hold Reg. 8, 12, 16, ..., 1024 0 P1 RESET Comparator Pin Logic Delay Counter EDG1 TC1 Capture/Compare Reg. PAC1 TC1H Hold Reg. PA1H Hold Reg. 8, 12, 16, ..., 1024 0 P2 RESET Comparator Pin Logic Delay Counter EDG2 TC2 Capture/Compare Reg. PAC2 TC2H Hold Reg. PA2H Hold Reg. 8, 12, 16, ..., 1024 0 P3 RESET Comparator Pin Logic Delay Counter EDG3 TC3 Capture/Compare Reg. PAC3 TC3H Hold Reg. PA3H Hold Reg. P4 Pin Logic LATCH 8, 12, 16, ..., 1024 Comparator EDG4 EDG0 TC4 Capture/Compare Reg. MUX ICLAT, LATQ, BUFEN (Force Latch) SH04 P5 Pin Logic Comparator EDG5 EDG1 TC5 Capture/Compare Reg. MUX Write 0x0000 to Modulus Counter SH15 P6 Pin Logic Comparator EDG6 EDG2 LATQ (MDC Latch Enable) TC6 Capture/Compare Reg. MUX SH26 P7 Pin Logic Comparator EDG7 EDG3 TC7 Capture/Compare Reg. MUX SH37 Figure 7-66. Detailed Timer Block Diagram in Latch Mode when PRNT = 1 MC9S12XDP512 Data Sheet, Rev. 2.21 352 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 16-Bit Free-Running 16 BITMain MAIN TIMER Timer / 1, 4, 8, 16 Bus Clock 16-Bit Load Register 16-Bit Modulus Down Counter Modulus Prescaler 0 Delay Counter EDG0 TC0 Capture/Compare Reg. PAC0 TC0H Hold Reg. PA0H Hold Reg. 0 Pin Logic Delay Counter EDG1 TC1 Capture/Compare Reg. PAC1 TC1H Hold Reg. PA1H Hold Reg. 0 P2 P4 Pin Logic Delay Counter EDG2 TC2 Capture/Compare Reg. PAC2 TC2H Hold Reg. PA2H Hold Reg. Delay Counter EDG3 TC3 Capture/Compare Reg. PAC3 TC3H Hold Reg. PA3H Hold Reg. Comparator EDG4 TC4 Capture/Compare Reg. LATQ, BUFEN (Queue Mode) Comparator Read TC3H Hold Reg. MUX EDG0 SH04 P5 Pin Logic EDG5 TC5 Capture/Compare Reg. MUX EDG1 Read TC2H Hold Reg. SH15 P6 Pin Logic RESET Comparator Pin Logic Pin Logic RESET Comparator 0 P3 RESET Comparator LATCH1 P1 LATCH0 Pin Logic LATCH2 P0 RESET Comparator LATCH3 Bus Clock /1, 2, ..., 128 Timer Prescaler Comparator EDG6 TC6 Capture/Compare Reg. MUX EDG2 Read TC1H Hold Reg. SH26 P7 Pin Logic Comparator EDG7 EDG3 SH37 TC7 Capture/Compare Reg. Read TC0H Hold Reg. MUX Figure 7-67. Detailed Timer Block Diagram in Queue Mode when PRNT = 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 353 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) /1, 2, 3, ... 256 Bus Clock 16-Bit Free-Running 16 BITMain MAIN TIMER Timer Timer Prescaler / 1, 2, 3, ... 256 16-Bit Load Register Modulus Prescaler 16-Bit Modulus Down Counter Bus Clock 0 P0 RESET Comparator Pin Logic Delay Counter EDG0 TC0 Capture/Compare Reg. PAC0 TC0H Hold Reg. PA0H Hold Reg. 0 P1 LATCH0 8, 12, 16, ... 1024 RESET Comparator Pin Logic Delay Counter EDG1 TC1 Capture/Compare Reg. PAC1 TC1H Hold Reg. PA1H Hold Reg. 0 P2 LATCH1 8, 12, 16, ... 1024 RESET Comparator Pin Logic Delay Counter EDG2 TC2 Capture/Compare Reg. PAC2 TC2H Hold Reg. PA2H Hold Reg. 0 RESET Comparator Pin Logic Delay Counter EDG3 TC3 Capture/Compare Reg. PAC3 TC3H Hold Reg. PA3H Hold Reg. 8, 12, 16, ... 1024 P4 Pin Logic Comparator EDG4 TC4 Capture/Compare Reg. LATQ, BUFEN (Queue Mode) Comparator Read TC3H Hold Reg. MUX EDG0 SH04 P5 Pin Logic EDG5 TC5 Capture/Compare Reg. MUX EDG1 Read TC2H Hold Reg. SH15 P6 Pin Logic LATCH3 P3 LATCH2 8, 12, 16, ... 1024 Comparator EDG6 TC6 Capture/Compare Reg. MUX EDG2 Read TC1H Hold Reg. SH26 P7 Pin Logic Comparator EDG7 EDG3 SH37 TC7 Capture/Compare Reg. Read TC0H Hold Reg. MUX Figure 7-68. Detailed Timer Block Diagram in Queue Mode when PRNT = 1 MC9S12XDP512 Data Sheet, Rev. 2.21 354 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) Load Holding Register and Reset Pulse Accumulator 0 8, 12,16, ..., 1024 8-Bit PAC0 (PACN0) EDG0 P0 Edge Detector Delay Counter PA0H Holding Register Interrupt 0 8, 12,16, ..., 1024 EDG1 P1 Edge Detector 8-Bit PAC1 (PACN1) Delay Counter PA1H Holding Register 0 8, 12,16, ..., 1024 EDG2 P2 Edge Detector 8-Bit PAC2 (PACN2) Delay Counter PA2H Holding Register Interrupt 8, 12,16, ..., 1024 P3 Edge Detector 0 EDG3 8-Bit PAC3 (PACN3) Delay Counter PA3H Holding Register Figure 7-69. 8-Bit Pulse Accumulators Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 355 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) TIMCLK (Timer Clock) CLK1 CLK0 PACLK / 256 Clock Select (PAMOD) PACLK PACLK / 65536 Prescaled Clock (PCLK) 4:1 MUX Edge Detector P7 Interrupt 8-Bit PAC3 (PACN3) 8-Bit PAC2 (PACN2) MUX PACA Bus Clock Divide by 64 Interrupt 8-Bit PAC1 (PACN1) 8-Bit PAC0 (PACN0) Delay Counter PACB Edge Detector P0 Figure 7-70. 16-Bit Pulse Accumulators Block Diagram 16-Bit Main Timer Px Edge Detector Delay Counter Set CxF Interrupt TCx Input Capture Register TCxH I.C. Holding Register BUFEN * LATQ * TFMOD Figure 7-71. Block Diagram for Port 7 with Output Compare/Pulse Accumulator A MC9S12XDP512 Data Sheet, Rev. 2.21 356 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.4.1 Enhanced Capture Timer Modes of Operation The enhanced capture timer has 8 input capture, output compare (IC/OC) channels, same as on the HC12 standard timer (timer channels TC0 to TC7). When channels are selected as input capture by selecting the IOSx bit in TIOS register, they are called input capture (IC) channels. Four IC channels (channels 7-4) are the same as on the standard timer with one capture register each that memorizes the timer value captured by an action on the associated input pin. Four other IC channels (channels 3-0), in addition to the capture register, also have one buffer each called a holding register. This allows two different timer values to be saved without generating any interrupts. Four 8-bit pulse accumulators are associated with the four buffered IC channels (channels 3-0). Each pulse accumulator has a holding register to memorize their value by an action on its external input. Each pair of pulse accumulators can be used as a 16-bit pulse accumulator. The 16-bit modulus down-counter can control the transfer of the IC registers and the pulse accumulators contents to the respective holding registers for a given period, every time the count reaches zero. The modulus down-counter can also be used as a stand-alone time base with periodic interrupt capability. 7.4.1.1 IC Channels The IC channels are composed of four standard IC registers and four buffered IC channels. * An IC register is empty when it has been read or latched into the holding register. * A holding register is empty when it has been read. 7.4.1.1.1 Non-Buffered IC Channels The main timer value is memorized in the IC register by a valid input pin transition. If the corresponding NOVWx bit of the ICOVW register is cleared, with a new occurrence of a capture, the contents of IC register are overwritten by the new value. If the corresponding NOVWx bit of the ICOVW register is set, the capture register cannot be written unless it is empty. This will prevent the captured value from being overwritten until it is read. 7.4.1.1.2 Buffered IC Channels There are two modes of operations for the buffered IC channels: 1. IC latch mode (LATQ = 1) The main timer value is memorized in the IC register by a valid input pin transition (see Figure 7-65 and Figure 7-66). The value of the buffered IC register is latched to its holding register by the modulus counter for a given period when the count reaches zero, by a write 0x0000 to the modulus counter or by a write to ICLAT in the MCCTL register. If the corresponding NOVWx bit of the ICOVW register is cleared, with a new occurrence of a capture, the contents of IC register are overwritten by the new value. In case of latching, the contents of its holding register are overwritten. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 357 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) If the corresponding NOVWx bit of the ICOVW register is set, the capture register or its holding register cannot be written by an event unless they are empty (see Section 7.4.1.1, "IC Channels"). This will prevent the captured value from being overwritten until it is read or latched in the holding register. 2. IC Queue Mode (LATQ = 0) The main timer value is memorized in the IC register by a valid input pin transition (see Figure 7-67 and Figure 7-68). If the corresponding NOVWx bit of the ICOVW register is cleared, with a new occurrence of a capture, the value of the IC register will be transferred to its holding register and the IC register memorizes the new timer value. If the corresponding NOVWx bit of the ICOVW register is set, the capture register or its holding register cannot be written by an event unless they are empty (see Section 7.4.1.1, "IC Channels"). In queue mode, reads of the holding register will latch the corresponding pulse accumulator value to its holding register. 7.4.1.1.3 Delayed IC Channels There are four delay counters in this module associated with IC channels 0-3. The use of this feature is explained in the diagram and notes below. BUS CLOCK DLY_CNT 0 1 2 3 INPUT ON CH0-3 255 Cycles INPUT ON CH0-3 255.5 Cycles INPUT ON CH0-3 255.5 Cycles INPUT ON CH0-3 256 Cycles 253 254 255 256 Rejected Rejected Accepted Accepted Figure 7-72. Channel Input Validity with Delay Counter Feature In Figure 7-72 a delay counter value of 256 bus cycles is considered. 1. Input pulses with a duration of (DLY_CNT - 1) cycles or shorter are rejected. 2. Input pulses with a duration between (DLY_CNT - 1) and DLY_CNT cycles may be rejected or accepted, depending on their relative alignment with the sample points. 3. Input pulses with a duration between (DLY_CNT - 1) and DLY_CNT cycles may be rejected or accepted, depending on their relative alignment with the sample points. 4. Input pulses with a duration of DLY_CNT or longer are accepted. MC9S12XDP512 Data Sheet, Rev. 2.21 358 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.4.1.2 OC Channel Initialization Internal register whose output drives OCx when TIOS is set, can be force loaded with a desired data by writing to CFORC register before OCx is configured for output compare action. This allows a glitch free switch over of port from general purpose I/O to timer output once the output compare is enabled. 7.4.1.3 Pulse Accumulators There are four 8-bit pulse accumulators with four 8-bit holding registers associated with the four IC buffered channels 3-0. A pulse accumulator counts the number of active edges at the input of its channel. The minimum pulse width for the PAI input is greater than two bus clocks.The maximum input frequency on the pulse accumulator channel is one half the bus frequency or Eclk. The user can prevent the 8-bit pulse accumulators from counting further than 0x00FF by utilizing the PACMX control bit in the ICSYS register. In this case, a value of 0x00FF means that 255 counts or more have occurred. Each pair of pulse accumulators can be used as a 16-bit pulse accumulator (see Figure 7-70). Pulse accumulator B operates only as an event counter, it does not feature gated time accumulation mode.The edge control for pulse accumulator B as a 16-bit pulse accumulator is defined by TCTL4[1:0]. To operate the 16-bit pulse accumulators A and B (PACA and PACB) independently of input capture or output compare 7 and 0 respectively, the user must set the corresponding bits: IOSx = 1, OMx = 0, and OLx = 0. OC7M7 or OC7M0 in the OC7M register must also be cleared. There are two modes of operation for the pulse accumulators: * Pulse accumulator latch mode The value of the pulse accumulator is transferred to its holding register when the modulus down-counter reaches zero, a write 0x0000 to the modulus counter or when the force latch control bit ICLAT is written. At the same time the pulse accumulator is cleared. * Pulse accumulator queue mode When queue mode is enabled, reads of an input capture holding register will transfer the contents of the associated pulse accumulator to its holding register. At the same time the pulse accumulator is cleared. 7.4.1.4 Modulus Down-Counter The modulus down-counter can be used as a time base to generate a periodic interrupt. It can also be used to latch the values of the IC registers and the pulse accumulators to their holding registers. The action of latching can be programmed to be periodic or only once. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 359 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.4.1.5 Precision Timer By enabling the PRNT bit of the TSCR1 register, the performance of the timer can be enhanced. In this case, it is possible to set additional prescaler settings for the main timer counter and modulus down counter and enhance delay counter settings compared to the settings in the present ECT timer. 7.4.1.6 Flag Clearing Mechanisms The flags in the ECT can be cleared one of two ways: 1. Normal flag clearing mechanism (TFFCA = 0) Any of the ECT flags can be cleared by writing a one to the flag. 2. Fast flag clearing mechanism (TFFCA = 1) With the timer fast flag clear all (TFFCA) enabled, the ECT flags can only be cleared by accessing the various registers associated with the ECT modes of operation as described below. The flags cannot be cleared via the normal flag clearing mechanism. This fast flag clearing mechanism has the advantage of eliminating the software overhead required by a separate clear sequence. Extra care must be taken to avoid accidental flag clearing due to unintended accesses. -- Input capture A read from an input capture channel register causes the corresponding channel flag, CxF, to be cleared in the TFLG1 register. -- Output compare A write to the output compare channel register causes the corresponding channel flag, CxF, to be cleared in the TFLG1 register. -- Timer counter Any access to the TCNT register clears the TOF flag in the TFLG2 register. -- Pulse accumulator A Any access to the PACN3 and PACN2 registers clears the PAOVF and PAIF flags in the PAFLG register. -- Pulse accumulator B Any access to the PACN1 and PACN0 registers clears the PBOVF flag in the PBFLG register. -- Modulus down counter Any access to the MCCNT register clears the MCZF flag in the MCFLG register. 7.4.2 Reset The reset state of each individual bit is listed within the register description section (Section 7.3, "Memory Map and Register Definition") which details the registers and their bit-fields. MC9S12XDP512 Data Sheet, Rev. 2.21 360 Freescale Semiconductor Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) 7.4.3 Interrupts This section describes interrupts originated by the ECT block. The MCU must service the interrupt requests. Table 7-37 lists the interrupts generated by the ECT to communicate with the MCU. Table 7-37. ECT Interrupts Interrupt Source Description Timer channel 7-0 Active high timer channel interrupts 7-0 Modulus counter underflow Active high modulus counter interrupt Pulse accumulator B overflow Active high pulse accumulator B interrupt Pulse accumulator A input Active high pulse accumulator A input interrupt Pulse accumulator A overflow Pulse accumulator overflow interrupt Timer overflow Timer 0verflow interrupt The ECT only originates interrupt requests. The following is a description of how the module makes a request and how the MCU should acknowledge that request. The interrupt vector offset and interrupt number are chip dependent. 7.4.3.1 Channel [7:0] Interrupt This active high output will be asserted by the module to request a timer channel 7-0 interrupt to be serviced by the system controller. 7.4.3.2 Modulus Counter Interrupt This active high output will be asserted by the module to request a modulus counter underflow interrupt to be serviced by the system controller. 7.4.3.3 Pulse Accumulator B Overflow Interrupt This active high output will be asserted by the module to request a timer pulse accumulator B overflow interrupt to be serviced by the system controller. 7.4.3.4 Pulse Accumulator A Input Interrupt This active high output will be asserted by the module to request a timer pulse accumulator A input interrupt to be serviced by the system controller. 7.4.3.5 Pulse Accumulator A Overflow Interrupt This active high output will be asserted by the module to request a timer pulse accumulator A overflow interrupt to be serviced by the system controller. 7.4.3.6 Timer Overflow Interrupt This active high output will be asserted by the module to request a timer overflow interrupt to be serviced by the system controller. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 361 Chapter 7 Enhanced Capture Timer (S12ECT16B8CV2) MC9S12XDP512 Data Sheet, Rev. 2.21 362 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.1 Introduction The PWM definition is based on the HC12 PWM definitions. It contains the basic features from the HC11 with some of the enhancements incorporated on the HC12: center aligned output mode and four available clock sources.The PWM module has eight channels with independent control of left and center aligned outputs on each channel. Each of the eight channels has a programmable period and duty cycle as well as a dedicated counter. A flexible clock select scheme allows a total of four different clock sources to be used with the counters. Each of the modulators can create independent continuous waveforms with software-selectable duty rates from 0% to 100%. The PWM outputs can be programmed as left aligned outputs or center aligned outputs. 8.1.1 Features The PWM block includes these distinctive features: * Eight independent PWM channels with programmable period and duty cycle * Dedicated counter for each PWM channel * Programmable PWM enable/disable for each channel * Software selection of PWM duty pulse polarity for each channel * Period and duty cycle are double buffered. Change takes effect when the end of the effective period is reached (PWM counter reaches zero) or when the channel is disabled. * Programmable center or left aligned outputs on individual channels * Eight 8-bit channel or four 16-bit channel PWM resolution * Four clock sources (A, B, SA, and SB) provide for a wide range of frequencies * Programmable clock select logic * Emergency shutdown 8.1.2 Modes of Operation There is a software programmable option for low power consumption in wait mode that disables the input clock to the prescaler. In freeze mode there is a software programmable option to disable the input clock to the prescaler. This is useful for emulation. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 363 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.1.3 Block Diagram Figure 8-1 shows the block diagram for the 8-bit 8-channel PWM block. PWM8B8C PWM Channels Channel 7 Period and Duty Counter Channel 6 Bus Clock Clock Select PWM Clock Period and Duty PWM6 Counter Channel 5 Period and Duty PWM7 PWM5 Counter Control Channel 4 Period and Duty PWM4 Counter Channel 3 Enable Period and Duty PWM3 Counter Channel 2 Polarity Period and Duty Alignment PWM2 Counter Channel 1 Period and Duty PWM1 Counter Channel 0 Period and Duty Counter PWM0 Figure 8-1. PWM Block Diagram 8.2 External Signal Description The PWM module has a total of 8 external pins. 8.2.1 PWM7 -- PWM Channel 7 This pin serves as waveform output of PWM channel 7 and as an input for the emergency shutdown feature. 8.2.2 PWM6 -- PWM Channel 6 This pin serves as waveform output of PWM channel 6. MC9S12XDP512 Data Sheet, Rev. 2.21 364 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.2.3 PWM5 -- PWM Channel 5 This pin serves as waveform output of PWM channel 5. 8.2.4 PWM4 -- PWM Channel 4 This pin serves as waveform output of PWM channel 4. 8.2.5 PWM3 -- PWM Channel 3 This pin serves as waveform output of PWM channel 3. 8.2.6 PWM3 -- PWM Channel 2 This pin serves as waveform output of PWM channel 2. 8.2.7 PWM3 -- PWM Channel 1 This pin serves as waveform output of PWM channel 1. 8.2.8 PWM3 -- PWM Channel 0 This pin serves as waveform output of PWM channel 0. 8.3 Memory Map and Register Definition This section describes in detail all the registers and register bits in the PWM module. The special-purpose registers and register bit functions that are not normally available to device end users, such as factory test control registers and reserved registers, are clearly identified by means of shading the appropriate portions of address maps and register diagrams. Notes explaining the reasons for restricting access to the registers and functions are also explained in the individual register descriptions. 8.3.1 Module Memory Map This section describes the content of the registers in the PWM module. The base address of the PWM module is determined at the MCU level when the MCU is defined. The register decode map is fixed and begins at the first address of the module address offset. The figure below shows the registers associated with the PWM and their relative offset from the base address. The register detail description follows the order they appear in the register map. Reserved bits within a register will always read as 0 and the write will be unimplemented. Unimplemented functions are indicated by shading the bit. . MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 365 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) NOTE Register Address = Base Address + Address Offset, where the Base Address is defined at the MCU level and the Address Offset is defined at the module level. 8.3.2 Register Descriptions This section describes in detail all the registers and register bits in the PWM module. Register Name PWME R W PWMPOL R W PWMCLK R W PWMPRCLK R Bit 7 6 5 4 3 2 1 Bit 0 PWME7 PWME6 PWME5 PWME4 PWME3 PWME2 PWME1 PWME0 PPOL7 PPOL6 PPOL5 PPOL4 PPOL3 PPOL2 PPOL1 PPOL0 PCLK7 PCLKL6 PCLK5 PCLK4 PCLK3 PCLK2 PCLK1 PCLK0 PCKB2 PCKB1 PCKB0 PCKA2 PCKA1 PCKA0 CAE7 CAE6 CAE5 CAE4 CAE3 CAE2 CAE1 CAE0 CON67 CON45 CON23 CON01 PSWAI PFRZ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W PWMCAE R W PWMCTL R W PWMTST1 R 0 W PWMPRSC1 R W PWMSCLA R W PWMSCLB R W PWMSCNTA R 1 W PWMSCNTB R 1 W = Unimplemented or Reserved Figure 8-2. PWM Register Summary (Sheet 1 of 3) MC9S12XDP512 Data Sheet, Rev. 2.21 366 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Register Name PWMCNT0 PWMCNT1 PWMCNT2 PWMCNT3 PWMCNT4 PWMCNT5 PWMCNT6 PWMCNT7 PWMPER0 Bit 7 6 5 4 3 2 1 Bit 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 R Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 R W PWMPER1 R W PWMPER2 R W PWMPER3 R W PWMPER4 R W PWMPER5 R W PWMPER6 R W = Unimplemented or Reserved Figure 8-2. PWM Register Summary (Sheet 2 of 3) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 367 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Register Name PWMPER7 R W PWMDTY0 R W PWMDTY1 R W PWMDTY2 R W PWMDTY3 R W PWMDTY4 R W PWMDTY5 R W PWMDTY6 R W PWMDTY7 R W PWMSDN R W Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 PWMIF PWMIE 0 PWM7IN PWM7INL PWM7ENA 0 PWMRSTRT PWMLVL = Unimplemented or Reserved Figure 8-2. PWM Register Summary (Sheet 3 of 3) 1 Intended for factory test purposes only. 8.3.2.1 PWM Enable Register (PWME) Each PWM channel has an enable bit (PWMEx) to start its waveform output. When any of the PWMEx bits are set (PWMEx = 1), the associated PWM output is enabled immediately. However, the actual PWM waveform is not available on the associated PWM output until its clock source begins its next cycle due to the synchronization of PWMEx and the clock source. NOTE The first PWM cycle after enabling the channel can be irregular. An exception to this is when channels are concatenated. Once concatenated mode is enabled (CONxx bits set in PWMCTL register), enabling/disabling the corresponding 16-bit PWM channel is controlled by the MC9S12XDP512 Data Sheet, Rev. 2.21 368 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) low order PWMEx bit.In this case, the high order bytes PWMEx bits have no effect and their corresponding PWM output lines are disabled. While in run mode, if all eight PWM channels are disabled (PWME7-0 = 0), the prescaler counter shuts off for power savings. R W Reset 7 6 5 4 3 2 1 0 PWME7 PWME6 PWME5 PWME4 PWME3 PWME2 PWME1 PWME0 0 0 0 0 0 0 0 0 Figure 8-3. PWM Enable Register (PWME) Read: Anytime Write: Anytime Table 8-1. PWME Field Descriptions Field Description 7 PWME7 Pulse Width Channel 7 Enable 0 Pulse width channel 7 is disabled. 1 Pulse width channel 7 is enabled. The pulse modulated signal becomes available at PWM output bit 7 when its clock source begins its next cycle. 6 PWME6 Pulse Width Channel 6 Enable 0 Pulse width channel 6 is disabled. 1 Pulse width channel 6 is enabled. The pulse modulated signal becomes available at PWM output bit6 when its clock source begins its next cycle. If CON67=1, then bit has no effect and PWM output line 6 is disabled. 5 PWME5 Pulse Width Channel 5 Enable 0 Pulse width channel 5 is disabled. 1 Pulse width channel 5 is enabled. The pulse modulated signal becomes available at PWM output bit 5 when its clock source begins its next cycle. 4 PWME4 Pulse Width Channel 4 Enable 0 Pulse width channel 4 is disabled. 1 Pulse width channel 4 is enabled. The pulse modulated signal becomes available at PWM, output bit 4 when its clock source begins its next cycle. If CON45 = 1, then bit has no effect and PWM output bit4 is disabled. 3 PWME3 Pulse Width Channel 3 Enable 0 Pulse width channel 3 is disabled. 1 Pulse width channel 3 is enabled. The pulse modulated signal becomes available at PWM, output bit 3 when its clock source begins its next cycle. 2 PWME2 Pulse Width Channel 2 Enable 0 Pulse width channel 2 is disabled. 1 Pulse width channel 2 is enabled. The pulse modulated signal becomes available at PWM, output bit 2 when its clock source begins its next cycle. If CON23 = 1, then bit has no effect and PWM output bit2 is disabled. 1 PWME1 Pulse Width Channel 1 Enable 0 Pulse width channel 1 is disabled. 1 Pulse width channel 1 is enabled. The pulse modulated signal becomes available at PWM, output bit 1 when its clock source begins its next cycle. 0 PWME0 Pulse Width Channel 0 Enable 0 Pulse width channel 0 is disabled. 1 Pulse width channel 0 is enabled. The pulse modulated signal becomes available at PWM, output bit 0 when its clock source begins its next cycle. If CON01 = 1, then bit has no effect and PWM output line0 is disabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 369 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.3.2.2 PWM Polarity Register (PWMPOL) The starting polarity of each PWM channel waveform is determined by the associated PPOLx bit in the PWMPOL register. If the polarity bit is one, the PWM channel output is high at the beginning of the cycle and then goes low when the duty count is reached. Conversely, if the polarity bit is zero, the output starts low and then goes high when the duty count is reached. R W Reset 7 6 5 4 3 2 1 0 PPOL7 PPOL6 PPOL5 PPOL4 PPOL3 PPOL2 PPOL1 PPOL0 0 0 0 0 0 0 0 0 Figure 8-4. PWM Polarity Register (PWMPOL) Read: Anytime Write: Anytime NOTE PPOLx register bits can be written anytime. If the polarity is changed while a PWM signal is being generated, a truncated or stretched pulse can occur during the transition Table 8-2. PWMPOL Field Descriptions Field 7-0 PPOL[7:0] 8.3.2.3 Description Pulse Width Channel 7-0 Polarity Bits 0 PWM channel 7-0 outputs are low at the beginning of the period, then go high when the duty count is reached. 1 PWM channel 7-0 outputs are high at the beginning of the period, then go low when the duty count is reached. PWM Clock Select Register (PWMCLK) Each PWM channel has a choice of two clocks to use as the clock source for that channel as described below. R W Reset 7 6 5 4 3 2 1 0 PCLK7 PCLKL6 PCLK5 PCLK4 PCLK3 PCLK2 PCLK1 PCLK0 0 0 0 0 0 0 0 0 Figure 8-5. PWM Clock Select Register (PWMCLK) Read: Anytime Write: Anytime MC9S12XDP512 Data Sheet, Rev. 2.21 370 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) NOTE Register bits PCLK0 to PCLK7 can be written anytime. If a clock select is changed while a PWM signal is being generated, a truncated or stretched pulse can occur during the transition. Table 8-3. PWMCLK Field Descriptions Field Description 7 PCLK7 Pulse Width Channel 7 Clock Select 0 Clock B is the clock source for PWM channel 7. 1 Clock SB is the clock source for PWM channel 7. 6 PCLK6 Pulse Width Channel 6 Clock Select 0 Clock B is the clock source for PWM channel 6. 1 Clock SB is the clock source for PWM channel 6. 5 PCLK5 Pulse Width Channel 5 Clock Select 0 Clock A is the clock source for PWM channel 5. 1 Clock SA is the clock source for PWM channel 5. 4 PCLK4 Pulse Width Channel 4 Clock Select 0 Clock A is the clock source for PWM channel 4. 1 Clock SA is the clock source for PWM channel 4. 3 PCLK3 Pulse Width Channel 3 Clock Select 0 Clock B is the clock source for PWM channel 3. 1 Clock SB is the clock source for PWM channel 3. 2 PCLK2 Pulse Width Channel 2 Clock Select 0 Clock B is the clock source for PWM channel 2. 1 Clock SB is the clock source for PWM channel 2. 1 PCLK1 Pulse Width Channel 1 Clock Select 0 Clock A is the clock source for PWM channel 1. 1 Clock SA is the clock source for PWM channel 1. 0 PCLK0 Pulse Width Channel 0 Clock Select 0 Clock A is the clock source for PWM channel 0. 1 Clock SA is the clock source for PWM channel 0. 8.3.2.4 PWM Prescale Clock Select Register (PWMPRCLK) This register selects the prescale clock source for clocks A and B independently. 7 R 6 0 W Reset 0 5 4 PCKB2 PCKB1 PCKB0 0 0 0 3 0 0 2 1 0 PCKA2 PCKA1 PCKA0 0 0 0 = Unimplemented or Reserved Figure 8-6. PWM Prescale Clock Select Register (PWMPRCLK) Read: Anytime Write: Anytime MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 371 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) NOTE PCKB2-0 and PCKA2-0 register bits can be written anytime. If the clock pre-scale is changed while a PWM signal is being generated, a truncated or stretched pulse can occur during the transition. Table 8-4. PWMPRCLK Field Descriptions Field Description 6-4 PCKB[2:0] Prescaler Select for Clock B -- Clock B is one of two clock sources which can be used for channels 2, 3, 6, or 7. These three bits determine the rate of clock B, as shown in Table 8-5. 2-0 PCKA[2:0] Prescaler Select for Clock A -- Clock A is one of two clock sources which can be used for channels 0, 1, 4 or 5. These three bits determine the rate of clock A, as shown in Table 8-6. s Table 8-5. Clock B Prescaler Selects PCKB2 PCKB1 PCKB0 Value of Clock B 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Bus clock Bus clock / 2 Bus clock / 4 Bus clock / 8 Bus clock / 16 Bus clock / 32 Bus clock / 64 Bus clock / 128 Table 8-6. Clock A Prescaler Selects 8.3.2.5 PCKA2 PCKA1 PCKA0 Value of Clock A 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Bus clock Bus clock / 2 Bus clock / 4 Bus clock / 8 Bus clock / 16 Bus clock / 32 Bus clock / 64 Bus clock / 128 PWM Center Align Enable Register (PWMCAE) The PWMCAE register contains eight control bits for the selection of center aligned outputs or left aligned outputs for each PWM channel. If the CAEx bit is set to a one, the corresponding PWM output will be center aligned. If the CAEx bit is cleared, the corresponding PWM output will be left aligned. See Section 8.4.2.5, "Left Aligned Outputs" and Section 8.4.2.6, "Center Aligned Outputs" for a more detailed description of the PWM output modes. R W Reset 7 6 5 4 3 2 1 0 CAE7 CAE6 CAE5 CAE4 CAE3 CAE2 CAE1 CAE0 0 0 0 0 0 0 0 0 Figure 8-7. PWM Center Align Enable Register (PWMCAE) MC9S12XDP512 Data Sheet, Rev. 2.21 372 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Read: Anytime Write: Anytime NOTE Write these bits only when the corresponding channel is disabled. Table 8-7. PWMCAE Field Descriptions Field 7-0 CAE[7:0] 8.3.2.6 Description Center Aligned Output Modes on Channels 7-0 0 Channels 7-0 operate in left aligned output mode. 1 Channels 7-0 operate in center aligned output mode. PWM Control Register (PWMCTL) The PWMCTL register provides for various control of the PWM module. 7 R W Reset 6 CON67 0 5 4 3 2 CON45 CON23 CON01 PSWAI PFRZ 0 0 0 0 0 1 0 0 0 0 0 = Unimplemented or Reserved Figure 8-8. PWM Control Register (PWMCTL) Read: Anytime Write: Anytime There are three control bits for concatenation, each of which is used to concatenate a pair of PWM channels into one 16-bit channel. When channels 6 and 7are concatenated, channel 6 registers become the high order bytes of the double byte channel. When channels 4 and 5 are concatenated, channel 4 registers become the high order bytes of the double byte channel. When channels 2 and 3 are concatenated, channel 2 registers become the high order bytes of the double byte channel. When channels 0 and 1 are concatenated, channel 0 registers become the high order bytes of the double byte channel. See Section 8.4.2.7, "PWM 16-Bit Functions" for a more detailed description of the concatenation PWM Function. NOTE Change these bits only when both corresponding channels are disabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 373 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Table 8-8. PWMCTL Field Descriptions Field Description 7 CON67 Concatenate Channels 6 and 7 0 Channels 6 and 7 are separate 8-bit PWMs. 1 Channels 6 and 7 are concatenated to create one 16-bit PWM channel. Channel 6 becomes the high order byte and channel 7 becomes the low order byte. Channel 7 output pin is used as the output for this 16-bit PWM (bit 7 of port PWMP). Channel 7 clock select control-bit determines the clock source, channel 7 polarity bit determines the polarity, channel 7 enable bit enables the output and channel 7 center aligned enable bit determines the output mode. 6 CON45 Concatenate Channels 4 and 5 0 Channels 4 and 5 are separate 8-bit PWMs. 1 Channels 4 and 5 are concatenated to create one 16-bit PWM channel. Channel 4 becomes the high order byte and channel 5 becomes the low order byte. Channel 5 output pin is used as the output for this 16-bit PWM (bit 5 of port PWMP). Channel 5 clock select control-bit determines the clock source, channel 5 polarity bit determines the polarity, channel 5 enable bit enables the output and channel 5 center aligned enable bit determines the output mode. 5 CON23 Concatenate Channels 2 and 3 0 Channels 2 and 3 are separate 8-bit PWMs. 1 Channels 2 and 3 are concatenated to create one 16-bit PWM channel. Channel 2 becomes the high order byte and channel 3 becomes the low order byte. Channel 3 output pin is used as the output for this 16-bit PWM (bit 3 of port PWMP). Channel 3 clock select control-bit determines the clock source, channel 3 polarity bit determines the polarity, channel 3 enable bit enables the output and channel 3 center aligned enable bit determines the output mode. 4 CON01 Concatenate Channels 0 and 1 0 Channels 0 and 1 are separate 8-bit PWMs. 1 Channels 0 and 1 are concatenated to create one 16-bit PWM channel. Channel 0 becomes the high order byte and channel 1 becomes the low order byte. Channel 1 output pin is used as the output for this 16-bit PWM (bit 1 of port PWMP). Channel 1 clock select control-bit determines the clock source, channel 1 polarity bit determines the polarity, channel 1 enable bit enables the output and channel 1 center aligned enable bit determines the output mode. 3 PSWAI PWM Stops in Wait Mode -- Enabling this bit allows for lower power consumption in wait mode by disabling the input clock to the prescaler. 0 Allow the clock to the prescaler to continue while in wait mode. 1 Stop the input clock to the prescaler whenever the MCU is in wait mode. 2 PFREZ PWM Counters Stop in Freeze Mode -- In freeze mode, there is an option to disable the input clock to the prescaler by setting the PFRZ bit in the PWMCTL register. If this bit is set, whenever the MCU is in freeze mode, the input clock to the prescaler is disabled. This feature is useful during emulation as it allows the PWM function to be suspended. In this way, the counters of the PWM can be stopped while in freeze mode so that once normal program flow is continued, the counters are re-enabled to simulate real-time operations. Since the registers can still be accessed in this mode, to re-enable the prescaler clock, either disable the PFRZ bit or exit freeze mode. 0 Allow PWM to continue while in freeze mode. 1 Disable PWM input clock to the prescaler whenever the part is in freeze mode. This is useful for emulation. 8.3.2.7 Reserved Register (PWMTST) This register is reserved for factory testing of the PWM module and is not available in normal modes. MC9S12XDP512 Data Sheet, Rev. 2.21 374 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 8-9. Reserved Register (PWMTST) Read: Always read $00 in normal modes Write: Unimplemented in normal modes NOTE Writing to this register when in special modes can alter the PWM functionality. 8.3.2.8 Reserved Register (PWMPRSC) This register is reserved for factory testing of the PWM module and is not available in normal modes. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 8-10. Reserved Register (PWMPRSC) Read: Always read $00 in normal modes Write: Unimplemented in normal modes NOTE Writing to this register when in special modes can alter the PWM functionality. 8.3.2.9 PWM Scale A Register (PWMSCLA) PWMSCLA is the programmable scale value used in scaling clock A to generate clock SA. Clock SA is generated by taking clock A, dividing it by the value in the PWMSCLA register and dividing that by two. Clock SA = Clock A / (2 * PWMSCLA) NOTE When PWMSCLA = $00, PWMSCLA value is considered a full scale value of 256. Clock A is thus divided by 512. Any value written to this register will cause the scale counter to load the new scale value (PWMSCLA). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 375 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Figure 8-11. PWM Scale A Register (PWMSCLA) Read: Anytime Write: Anytime (causes the scale counter to load the PWMSCLA value) 8.3.2.10 PWM Scale B Register (PWMSCLB) PWMSCLB is the programmable scale value used in scaling clock B to generate clock SB. Clock SB is generated by taking clock B, dividing it by the value in the PWMSCLB register and dividing that by two. Clock SB = Clock B / (2 * PWMSCLB) NOTE When PWMSCLB = $00, PWMSCLB value is considered a full scale value of 256. Clock B is thus divided by 512. Any value written to this register will cause the scale counter to load the new scale value (PWMSCLB). R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Figure 8-12. PWM Scale B Register (PWMSCLB) Read: Anytime Write: Anytime (causes the scale counter to load the PWMSCLB value). 8.3.2.11 Reserved Registers (PWMSCNTx) The registers PWMSCNTA and PWMSCNTB are reserved for factory testing of the PWM module and are not available in normal modes. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 8-13. Reserved Registers (PWMSCNTx) Read: Always read $00 in normal modes Write: Unimplemented in normal modes MC9S12XDP512 Data Sheet, Rev. 2.21 376 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) NOTE Writing to these registers when in special modes can alter the PWM functionality. 8.3.2.12 PWM Channel Counter Registers (PWMCNTx) Each channel has a dedicated 8-bit up/down counter which runs at the rate of the selected clock source. The counter can be read at any time without affecting the count or the operation of the PWM channel. In left aligned output mode, the counter counts from 0 to the value in the period register - 1. In center aligned output mode, the counter counts from 0 up to the value in the period register and then back down to 0. Any value written to the counter causes the counter to reset to $00, the counter direction to be set to up, the immediate load of both duty and period registers with values from the buffers, and the output to change according to the polarity bit. The counter is also cleared at the end of the effective period (see Section 8.4.2.5, "Left Aligned Outputs" and Section 8.4.2.6, "Center Aligned Outputs" for more details). When the channel is disabled (PWMEx = 0), the PWMCNTx register does not count. When a channel becomes enabled (PWMEx = 1), the associated PWM counter starts at the count in the PWMCNTx register. For more detailed information on the operation of the counters, see Section 8.4.2.4, "PWM Timer Counters". In concatenated mode, writes to the 16-bit counter by using a 16-bit access or writes to either the low or high order byte of the counter will reset the 16-bit counter. Reads of the 16-bit counter must be made by 16-bit access to maintain data coherency. NOTE Writing to the counter while the channel is enabled can cause an irregular PWM cycle to occur. R 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 W 0 0 0 0 0 0 0 0 Reset 0 0 0 0 0 0 0 0 Figure 8-14. PWM Channel Counter Registers (PWMCNTx) Read: Anytime Write: Anytime (any value written causes PWM counter to be reset to $00). 8.3.2.13 PWM Channel Period Registers (PWMPERx) There is a dedicated period register for each channel. The value in this register determines the period of the associated PWM channel. The period registers for each channel are double buffered so that if they change while the channel is enabled, the change will NOT take effect until one of the following occurs: * The effective period ends * The counter is written (counter resets to $00) * The channel is disabled MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 377 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) In this way, the output of the PWM will always be either the old waveform or the new waveform, not some variation in between. If the channel is not enabled, then writes to the period register will go directly to the latches as well as the buffer. NOTE Reads of this register return the most recent value written. Reads do not necessarily return the value of the currently active period due to the double buffering scheme. See Section 8.4.2.3, "PWM Period and Duty" for more information. To calculate the output period, take the selected clock source period for the channel of interest (A, B, SA, or SB) and multiply it by the value in the period register for that channel: * * Left aligned output (CAEx = 0) PWMx Period = Channel Clock Period * PWMPERx Center Aligned Output (CAEx = 1) PWMx Period = Channel Clock Period * (2 * PWMPERx) For boundary case programming values, please refer to Section 8.4.2.8, "PWM Boundary Cases". R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 1 1 1 1 1 1 1 1 Figure 8-15. PWM Channel Period Registers (PWMPERx) Read: Anytime Write: Anytime 8.3.2.14 PWM Channel Duty Registers (PWMDTYx) There is a dedicated duty register for each channel. The value in this register determines the duty of the associated PWM channel. The duty value is compared to the counter and if it is equal to the counter value a match occurs and the output changes state. The duty registers for each channel are double buffered so that if they change while the channel is enabled, the change will NOT take effect until one of the following occurs: * The effective period ends * The counter is written (counter resets to $00) * The channel is disabled In this way, the output of the PWM will always be either the old duty waveform or the new duty waveform, not some variation in between. If the channel is not enabled, then writes to the duty register will go directly to the latches as well as the buffer. MC9S12XDP512 Data Sheet, Rev. 2.21 378 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) NOTE Reads of this register return the most recent value written. Reads do not necessarily return the value of the currently active duty due to the double buffering scheme. See Section 8.4.2.3, "PWM Period and Duty" for more information. NOTE Depending on the polarity bit, the duty registers will contain the count of either the high time or the low time. If the polarity bit is one, the output starts high and then goes low when the duty count is reached, so the duty registers contain a count of the high time. If the polarity bit is zero, the output starts low and then goes high when the duty count is reached, so the duty registers contain a count of the low time. To calculate the output duty cycle (high time as a% of period) for a particular channel: * Polarity = 0 (PPOL x =0) Duty Cycle = [(PWMPERx-PWMDTYx)/PWMPERx] * 100% * Polarity = 1 (PPOLx = 1) Duty Cycle = [PWMDTYx / PWMPERx] * 100% For boundary case programming values, please refer to Section 8.4.2.8, "PWM Boundary Cases". R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 1 1 1 1 1 1 1 1 Figure 8-16. PWM Channel Duty Registers (PWMDTYx) Read: Anytime Write: Anytime 8.3.2.15 PWM Shutdown Register (PWMSDN) The PWMSDN register provides for the shutdown functionality of the PWM module in the emergency cases. For proper operation, channel 7 must be driven to the active level for a minimum of two bus clocks. 7 R W Reset 6 5 PWMIF PWMIE 0 0 0 PWMRSTRT 0 4 PWMLVL 0 3 2 0 PWM7IN 0 0 1 0 PWM7INL PWM7ENA 0 0 = Unimplemented or Reserved Figure 8-17. PWM Shutdown Register (PWMSDN) Read: Anytime Write: Anytime MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 379 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Table 8-9. PWMSDN Field Descriptions Field Description 7 PWMIF PWM Interrupt Flag -- Any change from passive to asserted (active) state or from active to passive state will be flagged by setting the PWMIF flag = 1. The flag is cleared by writing a logic 1 to it. Writing a 0 has no effect. 0 No change on PWM7IN input. 1 Change on PWM7IN input 6 PWMIE PWM Interrupt Enable -- If interrupt is enabled an interrupt to the CPU is asserted. 0 PWM interrupt is disabled. 1 PWM interrupt is enabled. 5 PWM Restart -- The PWM can only be restarted if the PWM channel input 7 is de-asserted. After writing a logic PWMRSTRT 1 to the PWMRSTRT bit (trigger event) the PWM channels start running after the corresponding counter passes next "counter == 0" phase. Also, if the PWM7ENA bit is reset to 0, the PWM do not start before the counter passes $00. The bit is always read as "0". 4 PWMLVL PWM Shutdown Output Level If active level as defined by the PWM7IN input, gets asserted all enabled PWM channels are immediately driven to the level defined by PWMLVL. 0 PWM outputs are forced to 0 1 Outputs are forced to 1. 2 PWM7IN PWM Channel 7 Input Status -- This reflects the current status of the PWM7 pin. 1 PWM7INL PWM Shutdown Active Input Level for Channel 7 -- If the emergency shutdown feature is enabled (PWM7ENA = 1), this bit determines the active level of the PWM7channel. 0 Active level is low 1 Active level is high 0 PWM7ENA PWM Emergency Shutdown Enable -- If this bit is logic 1, the pin associated with channel 7 is forced to input and the emergency shutdown feature is enabled. All the other bits in this register are meaningful only if PWM7ENA = 1. 0 PWM emergency feature disabled. 1 PWM emergency feature is enabled. 8.4 8.4.1 Functional Description PWM Clock Select There are four available clocks: clock A, clock B, clock SA (scaled A), and clock SB (scaled B). These four clocks are based on the bus clock. Clock A and B can be software selected to be 1, 1/2, 1/4, 1/8,..., 1/64, 1/128 times the bus clock. Clock SA uses clock A as an input and divides it further with a reloadable counter. Similarly, clock SB uses clock B as an input and divides it further with a reloadable counter. The rates available for clock SA are software selectable to be clock A divided by 2, 4, 6, 8,..., or 512 in increments of divide by 2. Similar rates are available for clock SB. Each PWM channel has the capability of selecting one of two clocks, either the pre-scaled clock (clock A or B) or the scaled clock (clock SA or SB). The block diagram in Figure 8-18 shows the four different clocks and how the scaled clocks are created. MC9S12XDP512 Data Sheet, Rev. 2.21 380 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.4.1.1 Prescale The input clock to the PWM prescaler is the bus clock. It can be disabled whenever the part is in freeze mode by setting the PFRZ bit in the PWMCTL register. If this bit is set, whenever the MCU is in freeze mode (freeze mode signal active) the input clock to the prescaler is disabled. This is useful for emulation in order to freeze the PWM. The input clock can also be disabled when all eight PWM channels are disabled (PWME7-0 = 0). This is useful for reducing power by disabling the prescale counter. Clock A and clock B are scaled values of the input clock. The value is software selectable for both clock A and clock B and has options of 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, or 1/128 times the bus clock. The value selected for clock A is determined by the PCKA2, PCKA1, PCKA0 bits in the PWMPRCLK register. The value selected for clock B is determined by the PCKB2, PCKB1, PCKB0 bits also in the PWMPRCLK register. 8.4.1.2 Clock Scale The scaled A clock uses clock A as an input and divides it further with a user programmable value and then divides this by 2. The scaled B clock uses clock B as an input and divides it further with a user programmable value and then divides this by 2. The rates available for clock SA are software selectable to be clock A divided by 2, 4, 6, 8,..., or 512 in increments of divide by 2. Similar rates are available for clock SB. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 381 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Clock A PCKA2 PCKA1 PCKA0 Clock A/2, A/4, A/6,....A/512 8-Bit Down Counter Clock to PWM Ch 0 PCLK0 Count = 1 M U X Load PWMSCLA M U X Clock SA DIV 2 PCLK1 M U X M Clock to PWM Ch 1 Clock to PWM Ch 2 U PCLK2 M U X 2 4 8 16 32 64 128 Divide by Prescaler Taps: X PCLK3 Clock B Clock B/2, B/4, B/6,....B/512 U M U X Clock to PWM Ch 4 PCLK4 M Count = 1 8-Bit Down Counter X M U X Load PWMSCLB DIV 2 Clock SB PCKB2 PCKB1 PCKB0 Clock to PWM Ch 5 PCLK5 M U X Clock to PWM Ch 6 PCLK6 PWME7-0 Bus Clock PFRZ Freeze Mode Signal Clock to PWM Ch 3 M U X Clock to PWM Ch 7 PCLK7 Prescale Scale Clock Select Figure 8-18. PWM Clock Select Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 382 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Clock A is used as an input to an 8-bit down counter. This down counter loads a user programmable scale value from the scale register (PWMSCLA). When the down counter reaches one, a pulse is output and the 8-bit counter is re-loaded. The output signal from this circuit is further divided by two. This gives a greater range with only a slight reduction in granularity. Clock SA equals clock A divided by two times the value in the PWMSCLA register. NOTE Clock SA = Clock A / (2 * PWMSCLA) When PWMSCLA = $00, PWMSCLA value is considered a full scale value of 256. Clock A is thus divided by 512. Similarly, clock B is used as an input to an 8-bit down counter followed by a divide by two producing clock SB. Thus, clock SB equals clock B divided by two times the value in the PWMSCLB register. NOTE Clock SB = Clock B / (2 * PWMSCLB) When PWMSCLB = $00, PWMSCLB value is considered a full scale value of 256. Clock B is thus divided by 512. As an example, consider the case in which the user writes $FF into the PWMSCLA register. Clock A for this case will be E divided by 4. A pulse will occur at a rate of once every 255x4 E cycles. Passing this through the divide by two circuit produces a clock signal at an E divided by 2040 rate. Similarly, a value of $01 in the PWMSCLA register when clock A is E divided by 4 will produce a clock at an E divided by 8 rate. Writing to PWMSCLA or PWMSCLB causes the associated 8-bit down counter to be re-loaded. Otherwise, when changing rates the counter would have to count down to $01 before counting at the proper rate. Forcing the associated counter to re-load the scale register value every time PWMSCLA or PWMSCLB is written prevents this. NOTE Writing to the scale registers while channels are operating can cause irregularities in the PWM outputs. 8.4.1.3 Clock Select Each PWM channel has the capability of selecting one of two clocks. For channels 0, 1, 4, and 5 the clock choices are clock A or clock SA. For channels 2, 3, 6, and 7 the choices are clock B or clock SB. The clock selection is done with the PCLKx control bits in the PWMCLK register. NOTE Changing clock control bits while channels are operating can cause irregularities in the PWM outputs. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 383 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.4.2 PWM Channel Timers The main part of the PWM module are the actual timers. Each of the timer channels has a counter, a period register and a duty register (each are 8-bit). The waveform output period is controlled by a match between the period register and the value in the counter. The duty is controlled by a match between the duty register and the counter value and causes the state of the output to change during the period. The starting polarity of the output is also selectable on a per channel basis. Shown below in Figure 8-19 is the block diagram for the PWM timer. Clock Source From Port PWMP Data Register 8-Bit Counter Gate PWMCNTx (Clock Edge Sync) Up/Down Reset 8-bit Compare = T M U X M U X Q PWMDTYx Q R To Pin Driver 8-bit Compare = PWMPERx PPOLx Q T CAEx Q R PWMEx Figure 8-19. PWM Timer Channel Block Diagram 8.4.2.1 PWM Enable Each PWM channel has an enable bit (PWMEx) to start its waveform output. When any of the PWMEx bits are set (PWMEx = 1), the associated PWM output signal is enabled immediately. However, the actual PWM waveform is not available on the associated PWM output until its clock source begins its next cycle due to the synchronization of PWMEx and the clock source. An exception to this is when channels are concatenated. Refer to Section 8.4.2.7, "PWM 16-Bit Functions" for more detail. NOTE The first PWM cycle after enabling the channel can be irregular. MC9S12XDP512 Data Sheet, Rev. 2.21 384 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) On the front end of the PWM timer, the clock is enabled to the PWM circuit by the PWMEx bit being high. There is an edge-synchronizing circuit to guarantee that the clock will only be enabled or disabled at an edge. When the channel is disabled (PWMEx = 0), the counter for the channel does not count. 8.4.2.2 PWM Polarity Each channel has a polarity bit to allow starting a waveform cycle with a high or low signal. This is shown on the block diagram as a mux select of either the Q output or the Q output of the PWM output flip flop. When one of the bits in the PWMPOL register is set, the associated PWM channel output is high at the beginning of the waveform, then goes low when the duty count is reached. Conversely, if the polarity bit is zero, the output starts low and then goes high when the duty count is reached. 8.4.2.3 PWM Period and Duty Dedicated period and duty registers exist for each channel and are double buffered so that if they change while the channel is enabled, the change will NOT take effect until one of the following occurs: * The effective period ends * The counter is written (counter resets to $00) * The channel is disabled In this way, the output of the PWM will always be either the old waveform or the new waveform, not some variation in between. If the channel is not enabled, then writes to the period and duty registers will go directly to the latches as well as the buffer. A change in duty or period can be forced into effect "immediately" by writing the new value to the duty and/or period registers and then writing to the counter. This forces the counter to reset and the new duty and/or period values to be latched. In addition, since the counter is readable, it is possible to know where the count is with respect to the duty value and software can be used to make adjustments NOTE When forcing a new period or duty into effect immediately, an irregular PWM cycle can occur. Depending on the polarity bit, the duty registers will contain the count of either the high time or the low time. 8.4.2.4 PWM Timer Counters Each channel has a dedicated 8-bit up/down counter which runs at the rate of the selected clock source (see Section 8.4.1, "PWM Clock Select" for the available clock sources and rates). The counter compares to two registers, a duty register and a period register as shown in Figure 8-19. When the PWM counter matches the duty register, the output flip-flop changes state, causing the PWM waveform to also change state. A match between the PWM counter and the period register behaves differently depending on what output mode is selected as shown in Figure 8-19 and described in Section 8.4.2.5, "Left Aligned Outputs" and Section 8.4.2.6, "Center Aligned Outputs". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 385 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Each channel counter can be read at anytime without affecting the count or the operation of the PWM channel. Any value written to the counter causes the counter to reset to $00, the counter direction to be set to up, the immediate load of both duty and period registers with values from the buffers, and the output to change according to the polarity bit. When the channel is disabled (PWMEx = 0), the counter stops. When a channel becomes enabled (PWMEx = 1), the associated PWM counter continues from the count in the PWMCNTx register. This allows the waveform to continue where it left off when the channel is re-enabled. When the channel is disabled, writing "0" to the period register will cause the counter to reset on the next selected clock. NOTE If the user wants to start a new "clean" PWM waveform without any "history" from the old waveform, the user must write to channel counter (PWMCNTx) prior to enabling the PWM channel (PWMEx = 1). Generally, writes to the counter are done prior to enabling a channel in order to start from a known state. However, writing a counter can also be done while the PWM channel is enabled (counting). The effect is similar to writing the counter when the channel is disabled, except that the new period is started immediately with the output set according to the polarity bit. NOTE Writing to the counter while the channel is enabled can cause an irregular PWM cycle to occur. The counter is cleared at the end of the effective period (see Section 8.4.2.5, "Left Aligned Outputs" and Section 8.4.2.6, "Center Aligned Outputs" for more details). Table 8-10. PWM Timer Counter Conditions Counter Clears ($00) Counter Counts Counter Stops When PWMCNTx register written to any value When PWM channel is enabled (PWMEx = 1). Counts from last value in PWMCNTx. When PWM channel is disabled (PWMEx = 0) Effective period ends 8.4.2.5 Left Aligned Outputs The PWM timer provides the choice of two types of outputs, left aligned or center aligned. They are selected with the CAEx bits in the PWMCAE register. If the CAEx bit is cleared (CAEx = 0), the corresponding PWM output will be left aligned. In left aligned output mode, the 8-bit counter is configured as an up counter only. It compares to two registers, a duty register and a period register as shown in the block diagram in Figure 8-19. When the PWM counter matches the duty register the output flip-flop changes state causing the PWM waveform to also change state. A match between the PWM counter and the period register resets the counter and the output flip-flop, as shown in Figure 8-19, as well as performing a load from the double buffer period and duty register to the associated registers, as described in Section 8.4.2.3, "PWM Period and Duty". The counter counts from 0 to the value in the period register - 1. MC9S12XDP512 Data Sheet, Rev. 2.21 386 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) NOTE Changing the PWM output mode from left aligned to center aligned output (or vice versa) while channels are operating can cause irregularities in the PWM output. It is recommended to program the output mode before enabling the PWM channel. PPOLx = 0 PPOLx = 1 PWMDTYx Period = PWMPERx Figure 8-20. PWM Left Aligned Output Waveform To calculate the output frequency in left aligned output mode for a particular channel, take the selected clock source frequency for the channel (A, B, SA, or SB) and divide it by the value in the period register for that channel. * PWMx Frequency = Clock (A, B, SA, or SB) / PWMPERx * PWMx Duty Cycle (high time as a% of period): -- Polarity = 0 (PPOLx = 0) * Duty Cycle = [(PWMPERx-PWMDTYx)/PWMPERx] * 100% -- Polarity = 1 (PPOLx = 1) Duty Cycle = [PWMDTYx / PWMPERx] * 100% As an example of a left aligned output, consider the following case: Clock Source = E, where E = 10 MHz (100 ns period) PPOLx = 0 PWMPERx = 4 PWMDTYx = 1 PWMx Frequency = 10 MHz/4 = 2.5 MHz PWMx Period = 400 ns PWMx Duty Cycle = 3/4 *100% = 75% The output waveform generated is shown in Figure 8-21. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 387 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) E = 100 ns Duty Cycle = 75% Period = 400 ns Figure 8-21. PWM Left Aligned Output Example Waveform 8.4.2.6 Center Aligned Outputs For center aligned output mode selection, set the CAEx bit (CAEx = 1) in the PWMCAE register and the corresponding PWM output will be center aligned. The 8-bit counter operates as an up/down counter in this mode and is set to up whenever the counter is equal to $00. The counter compares to two registers, a duty register and a period register as shown in the block diagram in Figure 8-19. When the PWM counter matches the duty register, the output flip-flop changes state, causing the PWM waveform to also change state. A match between the PWM counter and the period register changes the counter direction from an up-count to a down-count. When the PWM counter decrements and matches the duty register again, the output flip-flop changes state causing the PWM output to also change state. When the PWM counter decrements and reaches zero, the counter direction changes from a down-count back to an up-count and a load from the double buffer period and duty registers to the associated registers is performed, as described in Section 8.4.2.3, "PWM Period and Duty". The counter counts from 0 up to the value in the period register and then back down to 0. Thus the effective period is PWMPERx*2. NOTE Changing the PWM output mode from left aligned to center aligned output (or vice versa) while channels are operating can cause irregularities in the PWM output. It is recommended to program the output mode before enabling the PWM channel. PPOLx = 0 PPOLx = 1 PWMDTYx PWMDTYx PWMPERx PWMPERx Period = PWMPERx*2 Figure 8-22. PWM Center Aligned Output Waveform MC9S12XDP512 Data Sheet, Rev. 2.21 388 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) To calculate the output frequency in center aligned output mode for a particular channel, take the selected clock source frequency for the channel (A, B, SA, or SB) and divide it by twice the value in the period register for that channel. * PWMx Frequency = Clock (A, B, SA, or SB) / (2*PWMPERx) * PWMx Duty Cycle (high time as a% of period): -- Polarity = 0 (PPOLx = 0) Duty Cycle = [(PWMPERx-PWMDTYx)/PWMPERx] * 100% -- Polarity = 1 (PPOLx = 1) Duty Cycle = [PWMDTYx / PWMPERx] * 100% MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 389 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) As an example of a center aligned output, consider the following case: Clock Source = E, where E = 10 MHz (100 ns period) PPOLx = 0 PWMPERx = 4 PWMDTYx = 1 PWMx Frequency = 10 MHz/8 = 1.25 MHz PWMx Period = 800 ns PWMx Duty Cycle = 3/4 *100% = 75% Shown in Figure 8-23 is the output waveform generated. E = 100 ns E = 100 ns DUTY CYCLE = 75% PERIOD = 800 ns Figure 8-23. PWM Center Aligned Output Example Waveform 8.4.2.7 PWM 16-Bit Functions The PWM timer also has the option of generating 8-channels of 8-bits or 4-channels of 16-bits for greater PWM resolution. This 16-bit channel option is achieved through the concatenation of two 8-bit channels. The PWMCTL register contains four control bits, each of which is used to concatenate a pair of PWM channels into one 16-bit channel. Channels 6 and 7 are concatenated with the CON67 bit, channels 4 and 5 are concatenated with the CON45 bit, channels 2 and 3 are concatenated with the CON23 bit, and channels 0 and 1 are concatenated with the CON01 bit. NOTE Change these bits only when both corresponding channels are disabled. When channels 6 and 7 are concatenated, channel 6 registers become the high order bytes of the double byte channel, as shown in Figure 8-24. Similarly, when channels 4 and 5 are concatenated, channel 4 registers become the high order bytes of the double byte channel. When channels 2 and 3 are concatenated, channel 2 registers become the high order bytes of the double byte channel. When channels 0 and 1 are concatenated, channel 0 registers become the high order bytes of the double byte channel. When using the 16-bit concatenated mode, the clock source is determined by the low order 8-bit channel clock select control bits. That is channel 7 when channels 6 and 7 are concatenated, channel 5 when channels 4 and 5 are concatenated, channel 3 when channels 2 and 3 are concatenated, and channel 1 when channels 0 and 1 are concatenated. The resulting PWM is output to the pins of the corresponding low order 8-bit channel as also shown in Figure 8-24. The polarity of the resulting PWM output is controlled by the PPOLx bit of the corresponding low order 8-bit channel as well. MC9S12XDP512 Data Sheet, Rev. 2.21 390 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Clock Source 7 High Low PWMCNT6 PWCNT7 Period/Duty Compare PWM7 Clock Source 5 High Low PWMCNT4 PWCNT5 Period/Duty Compare PWM5 Clock Source 3 High Low PWMCNT2 PWCNT3 Period/Duty Compare PWM3 Clock Source 1 High Low PWMCNT0 PWCNT1 Period/Duty Compare PWM1 Figure 8-24. PWM 16-Bit Mode Once concatenated mode is enabled (CONxx bits set in PWMCTL register), enabling/disabling the corresponding 16-bit PWM channel is controlled by the low order PWMEx bit. In this case, the high order bytes PWMEx bits have no effect and their corresponding PWM output is disabled. In concatenated mode, writes to the 16-bit counter by using a 16-bit access or writes to either the low or high order byte of the counter will reset the 16-bit counter. Reads of the 16-bit counter must be made by 16-bit access to maintain data coherency. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 391 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) Either left aligned or center aligned output mode can be used in concatenated mode and is controlled by the low order CAEx bit. The high order CAEx bit has no effect. Table 8-11 is used to summarize which channels are used to set the various control bits when in 16-bit mode. Table 8-11. 16-bit Concatenation Mode Summary 8.4.2.8 CONxx PWMEx PPOLx PCLKx CAEx PWMx Output CON67 PWME7 PPOL7 PCLK7 CAE7 PWM7 CON45 PWME5 PPOL5 PCLK5 CAE5 PWM5 CON23 PWME3 PPOL3 PCLK3 CAE3 PWM3 CON01 PWME1 PPOL1 PCLK1 CAE1 PWM1 PWM Boundary Cases Table 8-12 summarizes the boundary conditions for the PWM regardless of the output mode (left aligned or center aligned) and 8-bit (normal) or 16-bit (concatenation). Table 8-12. PWM Boundary Cases 1 8.5 PWMDTYx PWMPERx PPOLx PWMx Output $00 (indicates no duty) >$00 1 Always low $00 (indicates no duty) >$00 0 Always high XX $001 (indicates no period) 1 Always high XX $001 (indicates no period) 0 Always low >= PWMPERx XX 1 Always high >= PWMPERx XX 0 Always low Counter = $00 and does not count. Resets The reset state of each individual bit is listed within the Section 8.3.2, "Register Descriptions" which details the registers and their bit-fields. All special functions or modes which are initialized during or just following reset are described within this section. * The 8-bit up/down counter is configured as an up counter out of reset. * All the channels are disabled and all the counters do not count. MC9S12XDP512 Data Sheet, Rev. 2.21 392 Freescale Semiconductor Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) 8.6 Interrupts The PWM module has only one interrupt which is generated at the time of emergency shutdown, if the corresponding enable bit (PWMIE) is set. This bit is the enable for the interrupt. The interrupt flag PWMIF is set whenever the input level of the PWM7 channel changes while PWM7ENA = 1 or when PWMENA is being asserted while the level at PWM7 is active. In stop mode or wait mode (with the PSWAI bit set), the emergency shutdown feature will drive the PWM outputs to their shutdown output levels but the PWMIF flag will not be set. A description of the registers involved and affected due to this interrupt is explained in Section 8.3.2.15, "PWM Shutdown Register (PWMSDN)". The PWM block only generates the interrupt and does not service it. The interrupt signal name is PWM interrupt signal. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 393 Chapter 8 Pulse-Width Modulator (S12PWM8B8CV1) MC9S12XDP512 Data Sheet, Rev. 2.21 394 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.1 Introduction The inter-IC bus (IIC) is a two-wire, bidirectional serial bus that provides a simple, efficient method of data exchange between devices. Being a two-wire device, the IIC bus minimizes the need for large numbers of connections between devices, and eliminates the need for an address decoder. This bus is suitable for applications requiring occasional communications over a short distance between a number of devices. It also provides flexibility, allowing additional devices to be connected to the bus for further expansion and system development. The interface is designed to operate up to 100 kbps with maximum bus loading and timing. The device is capable of operating at higher baud rates, up to a maximum of clock/20, with reduced bus loading. The maximum communication length and the number of devices that can be connected are limited by a maximum bus capacitance of 400 pF. 9.1.1 Features The IIC module has the following key features: * Compatible with I2C bus standard * Multi-master operation * Software programmable for one of 256 different serial clock frequencies * Software selectable acknowledge bit * Interrupt driven byte-by-byte data transfer * Arbitration lost interrupt with automatic mode switching from master to slave * Calling address identification interrupt * Start and stop signal generation/detection * Repeated start signal generation * Acknowledge bit generation/detection * Bus busy detection MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 395 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.1.2 Modes of Operation The IIC functions the same in normal, special, and emulation modes. It has two low power modes: wait and stop modes. 9.1.3 Block Diagram The block diagram of the IIC module is shown in Figure 9-1. IIC Registers Start Stop Arbitration Control Clock Control In/Out Data Shift Register Interrupt bus_clock SCL SDA Address Compare Figure 9-1. IIC Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 396 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.2 External Signal Description The IICV2 module has two external pins. 9.2.1 IIC_SCL -- Serial Clock Line Pin This is the bidirectional serial clock line (SCL) of the module, compatible to the IIC bus specification. 9.2.2 IIC_SDA -- Serial Data Line Pin This is the bidirectional serial data line (SDA) of the module, compatible to the IIC bus specification. 9.3 Memory Map and Register Definition This section provides a detailed description of all memory and registers for the IIC module. 9.3.1 Module Memory Map The memory map for the IIC module is given below in Table 1-1. The address listed for each register is the address offset.The total address for each register is the sum of the base address for the IIC module and the address offset for each register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 397 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.3.2 Register Descriptions This section consists of register descriptions in address order. Each description includes a standard register diagram with an associated figure number. Details of register bit and field function follow the register diagrams, in bit order. Register Name IBAD R W IBFD R W IBCR R W IBSR R Bit 7 6 5 4 3 2 1 ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 IBC7 IBC6 IBC5 IBC4 IBC3 IBC2 IBC1 IBEN IBIE MS/SL Tx/Rx TXAK 0 0 TCF IAAS IBB D7 D6 D5 IBAL W IBDR R W D4 RSTA 0 SRW D3 D2 IBIF D1 Bit 0 0 IBC0 IBSWAI RXAK D0 = Unimplemented or Reserved Figure 9-2. IIC Register Summary 9.3.2.1 IIC Address Register (IBAD) 7 6 5 4 3 2 1 ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 0 0 0 0 0 0 0 R 0 0 W Reset 0 = Unimplemented or Reserved Figure 9-3. IIC Bus Address Register (IBAD) Read and write anytime This register contains the address the IIC bus will respond to when addressed as a slave; note that it is not the address sent on the bus during the address transfer. Table 9-1. IBAD Field Descriptions Field Description 7:1 ADR[7:1] Slave Address -- Bit 1 to bit 7 contain the specific slave address to be used by the IIC bus module.The default mode of IIC bus is slave mode for an address match on the bus. 0 Reserved Reserved -- Bit 0 of the IBAD is reserved for future compatibility. This bit will always read 0. MC9S12XDP512 Data Sheet, Rev. 2.21 398 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.3.2.2 IIC Frequency Divider Register (IBFD) 7 6 5 4 3 2 1 0 IBC7 IBC6 IBC5 IBC4 IBC3 IBC2 IBC1 IBC0 0 0 0 0 0 0 0 0 R W Reset = Unimplemented or Reserved Figure 9-4. IIC Bus Frequency Divider Register (IBFD) Read and write anytime Table 9-2. IBFD Field Descriptions Field Description 7:0 IBC[7:0] I Bus Clock Rate 7:0 -- This field is used to prescale the clock for bit rate selection. The bit clock generator is implemented as a prescale divider -- IBC7:6, prescaled shift register -- IBC5:3 select the prescaler divider and IBC2-0 select the shift register tap point. The IBC bits are decoded to give the tap and prescale values as shown in Table 9-3. Table 9-3. I-Bus Tap and Prescale Values IBC2-0 (bin) SCL Tap (clocks) SDA Tap (clocks) 000 5 1 001 6 1 010 7 2 011 8 2 100 9 3 101 10 3 110 12 4 111 15 4 IBC5-3 (bin) scl2start (clocks) scl2stop (clocks) scl2tap (clocks) tap2tap (clocks) 000 2 7 4 1 001 2 7 4 2 010 2 9 6 4 011 6 9 6 8 100 14 17 14 16 101 30 33 30 32 110 62 65 62 64 111 126 129 126 128 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 399 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Table 9-4. Multiplier Factor IBC7-6 MUL 00 01 01 02 10 04 11 RESERVED The number of clocks from the falling edge of SCL to the first tap (Tap[1]) is defined by the values shown in the scl2tap column of Table 9-3, all subsequent tap points are separated by 2IBC5-3 as shown in the tap2tap column in Table 9-3. The SCL Tap is used to generated the SCL period and the SDA Tap is used to determine the delay from the falling edge of SCL to SDA changing, the SDA hold time. IBC7-6 defines the multiplier factor MUL. The values of MUL are shown in the Table 9-4. SCL Divider SCL SDA Hold SDA SDA SCL Hold(stop) SCL Hold(start) SCL START condition STOP condition Figure 9-5. SCL Divider and SDA Hold The equation used to generate the divider values from the IBFD bits is: SCL Divider = MUL x {2 x (scl2tap + [(SCL_Tap -1) x tap2tap] + 2)} MC9S12XDP512 Data Sheet, Rev. 2.21 400 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description The SDA hold delay is equal to the CPU clock period multiplied by the SDA Hold value shown in Table 9-5. The equation used to generate the SDA Hold value from the IBFD bits is: SDA Hold = MUL x {scl2tap + [(SDA_Tap - 1) x tap2tap] + 3} The equation for SCL Hold values to generate the start and stop conditions from the IBFD bits is: SCL Hold(start) = MUL x [scl2start + (SCL_Tap - 1) x tap2tap] SCL Hold(stop) = MUL x [scl2stop + (SCL_Tap - 1) x tap2tap] Table 9-5. IIC Divider and Hold Values (Sheet 1 of 5) IBC[7:0] (hex) SCL Divider (clocks) SDA Hold (clocks) SCL Hold (start) SCL Hold (stop) 20 22 24 26 28 30 34 40 28 32 36 40 44 48 56 68 48 56 64 72 80 88 104 128 80 96 112 128 144 160 192 240 160 192 224 7 7 8 8 9 9 10 10 7 7 9 9 11 11 13 13 9 9 13 13 17 17 21 21 9 9 17 17 25 25 33 33 17 17 33 6 7 8 9 10 11 13 16 10 12 14 16 18 20 24 30 18 22 26 30 34 38 46 58 38 46 54 62 70 78 94 118 78 94 110 11 12 13 14 15 16 18 21 15 17 19 21 23 25 29 35 25 29 33 37 41 45 53 65 41 49 57 65 73 81 97 121 81 97 113 MUL=1 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 401 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Table 9-5. IIC Divider and Hold Values (Sheet 2 of 5) IBC[7:0] (hex) SCL Divider (clocks) SDA Hold (clocks) SCL Hold (start) SCL Hold (stop) 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 256 288 320 384 480 320 384 448 512 576 640 768 960 640 768 896 1024 1152 1280 1536 1920 1280 1536 1792 2048 2304 2560 3072 3840 33 49 49 65 65 33 33 65 65 97 97 129 129 65 65 129 129 193 193 257 257 129 129 257 257 385 385 513 513 126 142 158 190 238 158 190 222 254 286 318 382 478 318 382 446 510 574 638 766 958 638 766 894 1022 1150 1278 1534 1918 129 145 161 193 241 161 193 225 257 289 321 385 481 321 385 449 513 577 641 769 961 641 769 897 1025 1153 1281 1537 1921 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 40 44 48 52 56 60 68 80 56 64 72 80 88 96 112 14 14 16 16 18 18 20 20 14 14 18 18 22 22 26 12 14 16 18 20 22 26 32 20 24 28 32 36 40 48 22 24 26 28 30 32 36 42 30 34 38 42 46 50 58 MUL=2 MC9S12XDP512 Data Sheet, Rev. 2.21 402 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Table 9-5. IIC Divider and Hold Values (Sheet 3 of 5) IBC[7:0] (hex) SCL Divider (clocks) SDA Hold (clocks) SCL Hold (start) SCL Hold (stop) 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 136 96 112 128 144 160 176 208 256 160 192 224 256 288 320 384 480 320 384 448 512 576 640 768 960 640 768 896 1024 1152 1280 1536 1920 1280 1536 1792 2048 2304 2560 3072 3840 2560 3072 3584 4096 26 18 18 26 26 34 34 42 42 18 18 34 34 50 50 66 66 34 34 66 66 98 98 130 130 66 66 130 130 194 194 258 258 130 130 258 258 386 386 514 514 258 258 514 514 60 36 44 52 60 68 76 92 116 76 92 108 124 140 156 188 236 156 188 220 252 284 316 380 476 316 380 444 508 572 636 764 956 636 764 892 1020 1148 1276 1532 1916 1276 1532 1788 2044 70 50 58 66 74 82 90 106 130 82 98 114 130 146 162 194 242 162 194 226 258 290 322 386 482 322 386 450 514 578 642 770 962 642 770 898 1026 1154 1282 1538 1922 1282 1538 1794 2050 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 403 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Table 9-5. IIC Divider and Hold Values (Sheet 4 of 5) IBC[7:0] (hex) SCL Divider (clocks) SDA Hold (clocks) SCL Hold (start) SCL Hold (stop) 7C 7D 7E 7F 4608 5120 6144 7680 770 770 1026 1026 2300 2556 3068 3836 2306 2562 3074 3842 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 80 88 96 104 112 120 136 160 112 128 144 160 176 192 224 272 192 224 256 288 320 352 416 512 320 384 448 512 576 640 768 960 640 768 896 1024 1152 1280 1536 1920 28 28 32 32 36 36 40 40 28 28 36 36 44 44 52 52 36 36 52 52 68 68 84 84 36 36 68 68 100 100 132 132 68 68 132 132 196 196 260 260 24 28 32 36 40 44 52 64 40 48 56 64 72 80 96 120 72 88 104 120 136 152 184 232 152 184 216 248 280 312 376 472 312 376 440 504 568 632 760 952 44 48 52 56 60 64 72 84 60 68 76 84 92 100 116 140 100 116 132 148 164 180 212 260 164 196 228 260 292 324 388 484 324 388 452 516 580 644 772 964 MUL=4 MC9S12XDP512 Data Sheet, Rev. 2.21 404 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Table 9-5. IIC Divider and Hold Values (Sheet 5 of 5) IBC[7:0] (hex) SCL Divider (clocks) SDA Hold (clocks) SCL Hold (start) SCL Hold (stop) A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF 1280 1536 1792 2048 2304 2560 3072 3840 2560 3072 3584 4096 4608 5120 6144 7680 5120 6144 7168 8192 9216 10240 12288 15360 132 132 260 260 388 388 516 516 260 260 516 516 772 772 1028 1028 516 516 1028 1028 1540 1540 2052 2052 632 760 888 1016 1144 1272 1528 1912 1272 1528 1784 2040 2296 2552 3064 3832 2552 3064 3576 4088 4600 5112 6136 7672 644 772 900 1028 1156 1284 1540 1924 1284 1540 1796 2052 2308 2564 3076 3844 2564 3076 3588 4100 4612 5124 6148 7684 9.3.2.3 IIC Control Register (IBCR) 7 6 5 4 3 IBEN IBIE MS/SL Tx/Rx TXAK R 1 0 0 0 IBSWAI RSTA W Reset 2 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 9-6. IIC Bus Control Register (IBCR) Read and write anytime MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 405 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Table 9-6. IBCR Field Descriptions Field Description 7 IBEN I-Bus Enable -- This bit controls the software reset of the entire IIC bus module. 0 The module is reset and disabled. This is the power-on reset situation. When low the interface is held in reset but registers can be accessed 1 The IIC bus module is enabled.This bit must be set before any other IBCR bits have any effect If the IIC bus module is enabled in the middle of a byte transfer the interface behaves as follows: slave mode ignores the current transfer on the bus and starts operating whenever a subsequent start condition is detected. Master mode will not be aware that the bus is busy, hence if a start cycle is initiated then the current bus cycle may become corrupt. This would ultimately result in either the current bus master or the IIC bus module losing arbitration, after which bus operation would return to normal. 6 IBIE I-Bus Interrupt Enable 0 Interrupts from the IIC bus module are disabled. Note that this does not clear any currently pending interrupt condition 1 Interrupts from the IIC bus module are enabled. An IIC bus interrupt occurs provided the IBIF bit in the status register is also set. 5 MS/SL Master/Slave Mode Select Bit -- Upon reset, this bit is cleared. When this bit is changed from 0 to 1, a START signal is generated on the bus, and the master mode is selected. When this bit is changed from 1 to 0, a STOP signal is generated and the operation mode changes from master to slave.A STOP signal should only be generated if the IBIF flag is set. MS/SL is cleared without generating a STOP signal when the master loses arbitration. 0 Slave Mode 1 Master Mode 4 Tx/Rx Transmit/Receive Mode Select Bit -- This bit selects the direction of master and slave transfers. When addressed as a slave this bit should be set by software according to the SRW bit in the status register. In master mode this bit should be set according to the type of transfer required. Therefore, for address cycles, this bit will always be high. 0 Receive 1 Transmit 3 TXAK Transmit Acknowledge Enable -- This bit specifies the value driven onto SDA during data acknowledge cycles for both master and slave receivers. The IIC module will always acknowledge address matches, provided it is enabled, regardless of the value of TXAK. Note that values written to this bit are only used when the IIC bus is a receiver, not a transmitter. 0 An acknowledge signal will be sent out to the bus at the 9th clock bit after receiving one byte data 1 No acknowledge signal response is sent (i.e., acknowledge bit = 1) 2 RSTA Repeat Start -- Writing a 1 to this bit will generate a repeated START condition on the bus, provided it is the current bus master. This bit will always be read as a low. Attempting a repeated start at the wrong time, if the bus is owned by another master, will result in loss of arbitration. 1 Generate repeat start cycle 1 Reserved -- Bit 1 of the IBCR is reserved for future compatibility. This bit will always read 0. RESERVED 0 IBSWAI I Bus Interface Stop in Wait Mode 0 IIC bus module clock operates normally 1 Halt IIC bus module clock generation in wait mode Wait mode is entered via execution of a CPU WAI instruction. In the event that the IBSWAI bit is set, all clocks internal to the IIC will be stopped and any transmission currently in progress will halt.If the CPU were woken up by a source other than the IIC module, then clocks would restart and the IIC would resume MC9S12XDP512 Data Sheet, Rev. 2.21 406 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description from where was during the previous transmission. It is not possible for the IIC to wake up the CPU when its internal clocks are stopped. If it were the case that the IBSWAI bit was cleared when the WAI instruction was executed, the IIC internal clocks and interface would remain alive, continuing the operation which was currently underway. It is also possible to configure the IIC such that it will wake up the CPU via an interrupt at the conclusion of the current operation. See the discussion on the IBIF and IBIE bits in the IBSR and IBCR, respectively. 9.3.2.4 R IIC Status Register (IBSR) 7 6 5 TCF IAAS IBB 4 3 2 0 SRW IBAL 1 0 RXAK IBIF W Reset 1 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 9-7. IIC Bus Status Register (IBSR) This status register is read-only with exception of bit 1 (IBIF) and bit 4 (IBAL), which are software clearable. Table 9-7. IBSR Field Descriptions Field Description 7 TCF Data Transferring Bit -- While one byte of data is being transferred, this bit is cleared. It is set by the falling edge of the 9th clock of a byte transfer. Note that this bit is only valid during or immediately following a transfer to the IIC module or from the IIC module. 0 Transfer in progress 1 Transfer complete 6 IAAS Addressed as a Slave Bit -- When its own specific address (I-bus address register) is matched with the calling address, this bit is set.The CPU is interrupted provided the IBIE is set.Then the CPU needs to check the SRW bit and set its Tx/Rx mode accordingly.Writing to the I-bus control register clears this bit. 0 Not addressed 1 Addressed as a slave 5 IBB Bus Busy Bit 0 This bit indicates the status of the bus. When a START signal is detected, the IBB is set. If a STOP signal is detected, IBB is cleared and the bus enters idle state. 1 Bus is busy 4 IBAL Arbitration Lost -- The arbitration lost bit (IBAL) is set by hardware when the arbitration procedure is lost. Arbitration is lost in the following circumstances: 1. SDA sampled low when the master drives a high during an address or data transmit cycle. 2. SDA sampled low when the master drives a high during the acknowledge bit of a data receive cycle. 3. A start cycle is attempted when the bus is busy. 4. A repeated start cycle is requested in slave mode. 5. A stop condition is detected when the master did not request it. This bit must be cleared by software, by writing a one to it. A write of 0 has no effect on this bit. 3 Reserved -- Bit 3 of IBSR is reserved for future use. A read operation on this bit will return 0. RESERVED MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 407 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Table 9-7. IBSR Field Descriptions (continued) Field Description 2 SRW Slave Read/Write -- When IAAS is set this bit indicates the value of the R/W command bit of the calling address sent from the master This bit is only valid when the I-bus is in slave mode, a complete address transfer has occurred with an address match and no other transfers have been initiated. Checking this bit, the CPU can select slave transmit/receive mode according to the command of the master. 0 Slave receive, master writing to slave 1 Slave transmit, master reading from slave 1 IBIF I-Bus Interrupt -- The IBIF bit is set when one of the following conditions occurs: -- Arbitration lost (IBAL bit set) -- Byte transfer complete (TCF bit set) -- Addressed as slave (IAAS bit set) It will cause a processor interrupt request if the IBIE bit is set. This bit must be cleared by software, writing a one to it. A write of 0 has no effect on this bit. 0 RXAK Received Acknowledge -- The value of SDA during the acknowledge bit of a bus cycle. If the received acknowledge bit (RXAK) is low, it indicates an acknowledge signal has been received after the completion of 8 bits data transmission on the bus. If RXAK is high, it means no acknowledge signal is detected at the 9th clock. 0 Acknowledge received 1 No acknowledge received 9.3.2.5 IIC Data I/O Register (IBDR) 7 6 5 4 3 2 1 0 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 R W Reset Figure 9-8. IIC Bus Data I/O Register (IBDR) In master transmit mode, when data is written to the IBDR a data transfer is initiated. The most significant bit is sent first. In master receive mode, reading this register initiates next byte data receiving. In slave mode, the same functions are available after an address match has occurred.Note that the Tx/Rx bit in the IBCR must correctly reflect the desired direction of transfer in master and slave modes for the transmission to begin. For instance, if the IIC is configured for master transmit but a master receive is desired, then reading the IBDR will not initiate the receive. Reading the IBDR will return the last byte received while the IIC is configured in either master receive or slave receive modes. The IBDR does not reflect every byte that is transmitted on the IIC bus, nor can software verify that a byte has been written to the IBDR correctly by reading it back. In master transmit mode, the first byte of data written to IBDR following assertion of MS/SL is used for the address transfer and should com.prise of the calling address (in position D7:D1) concatenated with the required R/W bit (in position D0). MC9S12XDP512 Data Sheet, Rev. 2.21 408 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.4 Functional Description This section provides a complete functional description of the IICV2. 9.4.1 I-Bus Protocol The IIC bus system uses a serial data line (SDA) and a serial clock line (SCL) for data transfer. All devices connected to it must have open drain or open collector outputs. Logic AND function is exercised on both lines with external pull-up resistors. The value of these resistors is system dependent. Normally, a standard communication is composed of four parts: START signal, slave address transmission, data transfer and STOP signal. They are described briefly in the following sections and illustrated in Figure 9-9. MSB SCL SDA 1 LSB 2 3 4 5 6 7 Calling Address Read/ Write MSB SDA MSB 9 AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W Start Signal SCL 8 1 XXX 3 4 5 6 7 8 Calling Address Read/ Write 3 4 5 6 7 8 D7 D6 D5 D4 D3 D2 D1 D0 Data Byte 1 XX Ack Bit 9 No Stop Ack Signal Bit MSB 9 AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W Start Signal 2 Ack Bit LSB 2 LSB 1 LSB 2 3 4 5 6 7 8 9 AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W Repeated Start Signal New Calling Address Read/ Write No Stop Ack Signal Bit Figure 9-9. IIC-Bus Transmission Signals 9.4.1.1 START Signal When the bus is free, i.e. no master device is engaging the bus (both SCL and SDA lines are at logical high), a master may initiate communication by sending a START signal.As shown in Figure 9-9, a START signal is defined as a high-to-low transition of SDA while SCL is high. This signal denotes the beginning of a new data transfer (each data transfer may contain several bytes of data) and brings all slaves out of their idle states. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 409 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description SDA SCL START Condition STOP Condition Figure 9-10. Start and Stop Conditions 9.4.1.2 Slave Address Transmission The first byte of data transfer immediately after the START signal is the slave address transmitted by the master. This is a seven-bit calling address followed by a R/W bit. The R/W bit tells the slave the desired direction of data transfer. 1 = Read transfer, the slave transmits data to the master. 0 = Write transfer, the master transmits data to the slave. Only the slave with a calling address that matches the one transmitted by the master will respond by sending back an acknowledge bit. This is done by pulling the SDA low at the 9th clock (see Figure 9-9). No two slaves in the system may have the same address. If the IIC bus is master, it must not transmit an address that is equal to its own slave address. The IIC bus cannot be master and slave at the same time.However, if arbitration is lost during an address cycle the IIC bus will revert to slave mode and operate correctly even if it is being addressed by another master. 9.4.1.3 Data Transfer As soon as successful slave addressing is achieved, the data transfer can proceed byte-by-byte in a direction specified by the R/W bit sent by the calling master All transfers that come after an address cycle are referred to as data transfers, even if they carry sub-address information for the slave device. Each data byte is 8 bits long. Data may be changed only while SCL is low and must be held stable while SCL is high as shown in Figure 9-9. There is one clock pulse on SCL for each data bit, the MSB being transferred first. Each data byte has to be followed by an acknowledge bit, which is signalled from the receiving device by pulling the SDA low at the ninth clock. So one complete data byte transfer needs nine clock pulses. If the slave receiver does not acknowledge the master, the SDA line must be left high by the slave. The master can then generate a stop signal to abort the data transfer or a start signal (repeated start) to commence a new calling. MC9S12XDP512 Data Sheet, Rev. 2.21 410 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description If the master receiver does not acknowledge the slave transmitter after a byte transmission, it means 'end of data' to the slave, so the slave releases the SDA line for the master to generate STOP or START signal. 9.4.1.4 STOP Signal The master can terminate the communication by generating a STOP signal to free the bus. However, the master may generate a START signal followed by a calling command without generating a STOP signal first. This is called repeated START. A STOP signal is defined as a low-to-high transition of SDA while SCL at logical 1 (see Figure 9-9). The master can generate a STOP even if the slave has generated an acknowledge at which point the slave must release the bus. 9.4.1.5 Repeated START Signal As shown in Figure 9-9, a repeated START signal is a START signal generated without first generating a STOP signal to terminate the communication. This is used by the master to communicate with another slave or with the same slave in different mode (transmit/receive mode) without releasing the bus. 9.4.1.6 Arbitration Procedure The Inter-IC bus is a true multi-master bus that allows more than one master to be connected on it. If two or more masters try to control the bus at the same time, a clock synchronization procedure determines the bus clock, for which the low period is equal to the longest clock low period and the high is equal to the shortest one among the masters. The relative priority of the contending masters is determined by a data arbitration procedure, a bus master loses arbitration if it transmits logic 1 while another master transmits logic 0. The losing masters immediately switch over to slave receive mode and stop driving SDA output. In this case the transition from master to slave mode does not generate a STOP condition. Meanwhile, a status bit is set by hardware to indicate loss of arbitration. 9.4.1.7 Clock Synchronization Because wire-AND logic is performed on SCL line, a high-to-low transition on SCL line affects all the devices connected on the bus. The devices start counting their low period and as soon as a device's clock has gone low, it holds the SCL line low until the clock high state is reached.However, the change of low to high in this device clock may not change the state of the SCL line if another device clock is within its low period. Therefore, synchronized clock SCL is held low by the device with the longest low period. Devices with shorter low periods enter a high wait state during this time (see Figure 9-10). When all devices concerned have counted off their low period, the synchronized clock SCL line is released and pulled high. There is then no difference between the device clocks and the state of the SCL line and all the devices start counting their high periods.The first device to complete its high period pulls the SCL line low again. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 411 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description WAIT Start Counting High Period SCL1 SCL2 SCL Internal Counter Reset Figure 9-11. IIC-Bus Clock Synchronization 9.4.1.8 Handshaking The clock synchronization mechanism can be used as a handshake in data transfer. Slave devices may hold the SCL low after completion of one byte transfer (9 bits). In such case, it halts the bus clock and forces the master clock into wait states until the slave releases the SCL line. 9.4.1.9 Clock Stretching The clock synchronization mechanism can be used by slaves to slow down the bit rate of a transfer. After the master has driven SCL low the slave can drive SCL low for the required period and then release it.If the slave SCL low period is greater than the master SCL low period then the resulting SCL bus signal low period is stretched. 9.4.2 Operation in Run Mode This is the basic mode of operation. 9.4.3 Operation in Wait Mode IIC operation in wait mode can be configured. Depending on the state of internal bits, the IIC can operate normally when the CPU is in wait mode or the IIC clock generation can be turned off and the IIC module enters a power conservation state during wait mode. In the later case, any transmission or reception in progress stops at wait mode entry. 9.4.4 Operation in Stop Mode The IIC is inactive in stop mode for reduced power consumption. The STOP instruction does not affect IIC register states. MC9S12XDP512 Data Sheet, Rev. 2.21 412 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.5 Resets The reset state of each individual bit is listed in Section 9.3, "Memory Map and Register Definition," which details the registers and their bit-fields. 9.6 Interrupts IICV2 uses only one interrupt vector. Table 9-8. Interrupt Summary Interrupt Offset Vector Priority IIC Interrupt -- -- -- Source Description IBAL, TCF, IAAS When either of IBAL, TCF or IAAS bits is set bits in IBSR may cause an interrupt based on arbitration register lost, transfer complete or address detect conditions Internally there are three types of interrupts in IIC. The interrupt service routine can determine the interrupt type by reading the status register. IIC Interrupt can be generated on 1. Arbitration lost condition (IBAL bit set) 2. Byte transfer condition (TCF bit set) 3. Address detect condition (IAAS bit set) The IIC interrupt is enabled by the IBIE bit in the IIC control register. It must be cleared by writing 0 to the IBF bit in the interrupt service routine. 9.7 9.7.1 9.7.1.1 Initialization/Application Information IIC Programming Examples Initialization Sequence Reset will put the IIC bus control register to its default status. Before the interface can be used to transfer serial data, an initialization procedure must be carried out, as follows: 1. Update the frequency divider register (IBFD) and select the required division ratio to obtain SCL frequency from system clock. 2. Update the IIC bus address register (IBAD) to define its slave address. 3. Set the IBEN bit of the IIC bus control register (IBCR) to enable the IIC interface system. 4. Modify the bits of the IIC bus control register (IBCR) to select master/slave mode, transmit/receive mode and interrupt enable or not. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 413 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.7.1.2 Generation of START After completion of the initialization procedure, serial data can be transmitted by selecting the 'master transmitter' mode. If the device is connected to a multi-master bus system, the state of the IIC bus busy bit (IBB) must be tested to check whether the serial bus is free. If the bus is free (IBB=0), the start condition and the first byte (the slave address) can be sent. The data written to the data register comprises the slave calling address and the LSB set to indicate the direction of transfer required from the slave. The bus free time (i.e., the time between a STOP condition and the following START condition) is built into the hardware that generates the START cycle. Depending on the relative frequencies of the system clock and the SCL period it may be necessary to wait until the IIC is busy after writing the calling address to the IBDR before proceeding with the following instructions. This is illustrated in the following example. An example of a program which generates the START signal and transmits the first byte of data (slave address) is shown below: CHFLAG BRSET IBSR,#$20,* ;WAIT FOR IBB FLAG TO CLEAR TXSTART BSET IBCR,#$30 ;SET TRANSMIT AND MASTER MODE;i.e. GENERATE START CONDITION MOVB CALLING,IBDR ;TRANSMIT THE CALLING ADDRESS, D0=R/W BRCLR IBSR,#$20,* ;WAIT FOR IBB FLAG TO SET IBFREE 9.7.1.3 Post-Transfer Software Response Transmission or reception of a byte will set the data transferring bit (TCF) to 1, which indicates one byte communication is finished. The IIC bus interrupt bit (IBIF) is set also; an interrupt will be generated if the interrupt function is enabled during initialization by setting the IBIE bit. Software must clear the IBIF bit in the interrupt routine first. The TCF bit will be cleared by reading from the IIC bus data I/O register (IBDR) in receive mode or writing to IBDR in transmit mode. Software may service the IIC I/O in the main program by monitoring the IBIF bit if the interrupt function is disabled. Note that polling should monitor the IBIF bit rather than the TCF bit because their operation is different when arbitration is lost. Note that when an interrupt occurs at the end of the address cycle the master will always be in transmit mode, i.e. the address is transmitted. If master receive mode is required, indicated by R/W bit in IBDR, then the Tx/Rx bit should be toggled at this stage. During slave mode address cycles (IAAS=1), the SRW bit in the status register is read to determine the direction of the subsequent transfer and the Tx/Rx bit is programmed accordingly. For slave mode data cycles (IAAS=0) the SRW bit is not valid, the Tx/Rx bit in the control register should be read to determine the direction of the current transfer. The following is an example of a software response by a 'master transmitter' in the interrupt routine. ISR TRANSMIT BCLR BRCLR BRCLR BRSET MOVB IBSR,#$02 IBCR,#$20,SLAVE IBCR,#$10,RECEIVE IBSR,#$01,END DATABUF,IBDR ;CLEAR THE IBIF FLAG ;BRANCH IF IN SLAVE MODE ;BRANCH IF IN RECEIVE MODE ;IF NO ACK, END OF TRANSMISSION ;TRANSMIT NEXT BYTE OF DATA MC9S12XDP512 Data Sheet, Rev. 2.21 414 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description 9.7.1.4 Generation of STOP A data transfer ends with a STOP signal generated by the 'master' device. A master transmitter can simply generate a STOP signal after all the data has been transmitted. The following is an example showing how a stop condition is generated by a master transmitter. MASTX END EMASTX TST BEQ BRSET MOVB DEC BRA BCLR RTI TXCNT END IBSR,#$01,END DATABUF,IBDR TXCNT EMASTX IBCR,#$20 ;GET VALUE FROM THE TRANSMITING COUNTER ;END IF NO MORE DATA ;END IF NO ACK ;TRANSMIT NEXT BYTE OF DATA ;DECREASE THE TXCNT ;EXIT ;GENERATE A STOP CONDITION ;RETURN FROM INTERRUPT If a master receiver wants to terminate a data transfer, it must inform the slave transmitter by not acknowledging the last byte of data which can be done by setting the transmit acknowledge bit (TXAK) before reading the 2nd last byte of data. Before reading the last byte of data, a STOP signal must be generated first. The following is an example showing how a STOP signal is generated by a master receiver. MASR DEC BEQ MOVB DEC BNE BSET RXCNT ENMASR RXCNT,D1 D1 NXMAR IBCR,#$08 ENMASR NXMAR BRA BCLR MOVB RTI NXMAR IBCR,#$20 IBDR,RXBUF 9.7.1.5 Generation of Repeated START LAMAR ;DECREASE THE RXCNT ;LAST BYTE TO BE READ ;CHECK SECOND LAST BYTE ;TO BE READ ;NOT LAST OR SECOND LAST ;SECOND LAST, DISABLE ACK ;TRANSMITTING ;LAST ONE, GENERATE `STOP' SIGNAL ;READ DATA AND STORE At the end of data transfer, if the master continues to want to communicate on the bus, it can generate another START signal followed by another slave address without first generating a STOP signal. A program example is as shown. RESTART BSET MOVB IBCR,#$04 CALLING,IBDR 9.7.1.6 Slave Mode ;ANOTHER START (RESTART) ;TRANSMIT THE CALLING ADDRESS;D0=R/W In the slave interrupt service routine, the module addressed as slave bit (IAAS) should be tested to check if a calling of its own address has just been received. If IAAS is set, software should set the transmit/receive mode select bit (Tx/Rx bit of IBCR) according to the R/W command bit (SRW). Writing to the IBCR clears the IAAS automatically. Note that the only time IAAS is read as set is from the interrupt at the end of the address cycle where an address match occurred, interrupts resulting from subsequent data transfers will have IAAS cleared. A data transfer may now be initiated by writing information to IBDR, for slave transmits, or dummy reading from IBDR, in slave receive mode. The slave will drive SCL low in-between byte transfers, SCL is released when the IBDR is accessed in the required mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 415 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description In slave transmitter routine, the received acknowledge bit (RXAK) must be tested before transmitting the next byte of data. Setting RXAK means an 'end of data' signal from the master receiver, after which it must be switched from transmitter mode to receiver mode by software. A dummy read then releases the SCL line so that the master can generate a STOP signal. 9.7.1.7 Arbitration Lost If several masters try to engage the bus simultaneously, only one master wins and the others lose arbitration. The devices which lost arbitration are immediately switched to slave receive mode by the hardware. Their data output to the SDA line is stopped, but SCL continues to be generated until the end of the byte during which arbitration was lost. An interrupt occurs at the falling edge of the ninth clock of this transfer with IBAL=1 and MS/SL=0. If one master attempts to start transmission while the bus is being engaged by another master, the hardware will inhibit the transmission; switch the MS/SL bit from 1 to 0 without generating STOP condition; generate an interrupt to CPU and set the IBAL to indicate that the attempt to engage the bus is failed. When considering these cases, the slave service routine should test the IBAL first and the software should clear the IBAL bit if it is set. MC9S12XDP512 Data Sheet, Rev. 2.21 416 Freescale Semiconductor Chapter 9 Inter-Integrated Circuit (IICV2) Block Description Clear IBIF Master Mode ? Y TX N Arbitration Lost ? Y RX Tx/Rx ? N Last Byte Transmitted ? N Clear IBAL Y RXAK=0 ? N Last Byte To Be Read ? N Y N Y Y IAAS=1 ? IAAS=1 ? Y N Address Transfer End Of Addr Cycle (Master Rx) ? N Y Y (Read) 2nd Last Y Byte To Be Read ? SRW=1 ? Write Next Byte To IBDR Generate Stop Signal Set TXAK =1 Generate Stop Signal Read Data From IBDR And Store ACK From Receiver ? N Read Data From IBDR And Store Tx Next Byte Set RX Mode Switch To Rx Mode Dummy Read From IBDR Dummy Read From IBDR Switch To Rx Mode RX TX Y Set TX Mode Write Data To IBDR Dummy Read From IBDR TX/RX ? N (Write) N Data Transfer RTI Figure 9-12. Flow-Chart of Typical IIC Interrupt Routine MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 417 Chapter 9 Inter-Integrated Circuit (IICV2) Block Description MC9S12XDP512 Data Sheet, Rev. 2.21 418 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.1 Introduction Freescale's scalable controller area network (S12MSCANV3) definition is based on the MSCAN12 definition, which is the specific implementation of the MSCAN concept targeted for the M68HC12 microcontroller family. The module is a communication controller implementing the CAN 2.0A/B protocol as defined in the Bosch specification dated September 1991. For users to fully understand the MSCAN specification, it is recommended that the Bosch specification be read first to familiarize the reader with the terms and concepts contained within this document. Though not exclusively intended for automotive applications, CAN protocol is designed to meet the specific requirements of a vehicle serial data bus: real-time processing, reliable operation in the EMI environment of a vehicle, cost-effectiveness, and required bandwidth. MSCAN uses an advanced buffer arrangement resulting in predictable real-time behavior and simplified application software. 10.1.1 Glossary ACK: Acknowledge of CAN message CAN: Controller Area Network CRC: Cyclic Redundancy Code EOF: End of Frame FIFO: First-In-First-Out Memory IFS: Inter-Frame Sequence SOF: Start of Frame CPU bus: CPU related read/write data bus CAN bus: CAN protocol related serial bus oscillator clock: Direct clock from external oscillator bus clock: CPU bus realated clock CAN clock: CAN protocol related clock MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 419 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.1.2 Block Diagram MSCAN Oscillator Clock Bus Clock CANCLK MUX Presc. Tq Clk Receive/ Transmit Engine RXCAN TXCAN Transmit Interrupt Req. Receive Interrupt Req. Errors Interrupt Req. Message Filtering and Buffering Control and Status Wake-Up Interrupt Req. Configuration Registers Wake-Up Low Pass Filter Figure 10-1. MSCAN Block Diagram 10.1.3 Features The basic features of the MSCAN are as follows: * Implementation of the CAN protocol -- Version 2.0A/B -- Standard and extended data frames -- Zero to eight bytes data length -- Programmable bit rate up to 1 Mbps1 -- Support for remote frames * Five receive buffers with FIFO storage scheme * Three transmit buffers with internal prioritization using a "local priority" concept * Flexible maskable identifier filter supports two full-size (32-bit) extended identifier filters, or four 16-bit filters, or eight 8-bit filters * Programmable wakeup functionality with integrated low-pass filter * Programmable loopback mode supports self-test operation * Programmable listen-only mode for monitoring of CAN bus * Programmable bus-off recovery functionality * Separate signalling and interrupt capabilities for all CAN receiver and transmitter error states (warning, error passive, bus-off) * Programmable MSCAN clock source either bus clock or oscillator clock 1. Depending on the actual bit timing and the clock jitter of the PLL. MC9S12XDP512 Data Sheet, Rev. 2.21 420 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) * * * Internal timer for time-stamping of received and transmitted messages Three low-power modes: sleep, power down, and MSCAN enable Global initialization of configuration registers 10.1.4 Modes of Operation The following modes of operation are specific to the MSCAN. See Section 10.4, "Functional Description," for details. * Listen-Only Mode * MSCAN Sleep Mode * MSCAN Initialization Mode * MSCAN Power Down Mode 10.2 External Signal Description The MSCAN uses two external pins: 10.2.1 RXCAN -- CAN Receiver Input Pin RXCAN is the MSCAN receiver input pin. 10.2.2 TXCAN -- CAN Transmitter Output Pin TXCAN is the MSCAN transmitter output pin. The TXCAN output pin represents the logic level on the CAN bus: 0 = Dominant state 1 = Recessive state 10.2.3 CAN System A typical CAN system with MSCAN is shown in Figure 10-2. Each CAN station is connected physically to the CAN bus lines through a transceiver device. The transceiver is capable of driving the large current needed for the CAN bus and has current protection against defective CAN or defective stations. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 421 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) CAN node 2 CAN node 1 CAN node n MCU CAN Controller (MSCAN) TXCAN RXCAN Transceiver CAN_H CAN_L CAN Bus Figure 10-2. CAN System 10.3 Memory Map and Register Definition This section provides a detailed description of all registers accessible in the MSCAN. 10.3.1 Module Memory Map Figure 10-3 gives an overview on all registers and their individual bits in the MSCAN memory map. The register address results from the addition of base address and address offset. The base address is determined at the MCU level and can be found in the MCU memory map description. The address offset is defined at the module level. The MSCAN occupies 64 bytes in the memory space. The base address of the MSCAN module is determined at the MCU level when the MCU is defined. The register decode map is fixed and begins at the first address of the module address offset. The detailed register descriptions follow in the order they appear in the register map. Register Name Bit 7 0x0000 CANCTL0 R 0x0001 CANCTL1 R W W RXFRM CANE 6 RXACT CLKSRC 5 CSWAI LOOPB 4 SYNCH LISTEN 3 2 1 Bit 0 TIME WUPE SLPRQ INITRQ BORM WUPM SLPAK INITAK = Unimplemented or Reserved u = Unaffected Figure 10-3. MSCAN Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 422 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Register Name 0x0002 CANBTR0 R 0x0003 CANBTR1 R 0x0004 CANRFLG R 0x0005 CANRIER 0x0006 CANTFLG 0x000D CANMISC 3 2 1 Bit 0 SJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 SAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 WUPIF CSCIF RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF WUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 0 TXE2 TXE1 TXE0 0 0 0 0 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 0 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 0 TX2 TX1 TX0 0 0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 R W R W R 0x000C Reserved 4 W 0x0008 CANTARQ 0x000B CANIDAC 5 W R 0x000A CANTBSEL 6 W 0x0007 CANTIER 0x0009 CANTAAK Bit 7 W W R W R W R W R W R W 0x000E CANRXERR R 0x000F CANTXERR R 0x0010-0x0013 CANIDAR0-3 R BOHOLD W W W = Unimplemented or Reserved u = Unaffected Figure 10-3. MSCAN Register Summary (continued) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 423 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Register Name 0x0014-0x0017 CANIDMRx R 0x0018-0x001B CANIDAR4-7 R 0x001C-0x001F CANIDMR4-7 R 0x0020-0x002F CANRXFG R 0x0030-0x003F CANTXFG R W W W Bit 7 6 5 4 3 2 1 Bit 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 See Section 10.3.3, "Programmer's Model of Message Storage" W See Section 10.3.3, "Programmer's Model of Message Storage" W = Unimplemented or Reserved u = Unaffected Figure 10-3. MSCAN Register Summary (continued) 10.3.2 Register Descriptions This section describes in detail all the registers and register bits in the MSCAN module. Each description includes a standard register diagram with an associated figure number. Details of register bit and field function follow the register diagrams, in bit order. All bits of all registers in this module are completely synchronous to internal clocks during a register read. 10.3.2.1 MSCAN Control Register 0 (CANCTL0) The CANCTL0 register provides various control bits of the MSCAN module as described below. 7 R 6 5 RXACT RXFRM 4 3 2 1 0 TIME WUPE SLPRQ INITRQ 0 0 0 1 SYNCH CSWAI W Reset: 0 0 0 0 = Unimplemented Figure 10-4. MSCAN Control Register 0 (CANCTL0) NOTE The CANCTL0 register, except WUPE, INITRQ, and SLPRQ, is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable again as soon as the initialization mode is exited (INITRQ = 0 and INITAK = 0). Read: Anytime MC9S12XDP512 Data Sheet, Rev. 2.21 424 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Write: Anytime when out of initialization mode; exceptions are read-only RXACT and SYNCH, RXFRM (which is set by the module only), and INITRQ (which is also writable in initialization mode). Table 10-1. CANCTL0 Register Field Descriptions Field Description 7 RXFRM1 Received Frame Flag -- This bit is read and clear only. It is set when a receiver has received a valid message correctly, independently of the filter configuration. After it is set, it remains set until cleared by software or reset. Clearing is done by writing a 1. Writing a 0 is ignored. This bit is not valid in loopback mode. 0 No valid message was received since last clearing this flag 1 A valid message was received since last clearing of this flag 6 RXACT Receiver Active Status -- This read-only flag indicates the MSCAN is receiving a message. The flag is controlled by the receiver front end. This bit is not valid in loopback mode. 0 MSCAN is transmitting or idle2 1 MSCAN is receiving a message (including when arbitration is lost)2 5 CSWAI3 CAN Stops in Wait Mode -- Enabling this bit allows for lower power consumption in wait mode by disabling all the clocks at the CPU bus interface to the MSCAN module. 0 The module is not affected during wait mode 1 The module ceases to be clocked during wait mode 4 SYNCH Synchronized Status -- This read-only flag indicates whether the MSCAN is synchronized to the CAN bus and able to participate in the communication process. It is set and cleared by the MSCAN. 0 MSCAN is not synchronized to the CAN bus 1 MSCAN is synchronized to the CAN bus 3 TIME Timer Enable -- This bit activates an internal 16-bit wide free running timer which is clocked by the bit clock rate. If the timer is enabled, a 16-bit time stamp will be assigned to each transmitted/received message within the active TX/RX buffer. Right after the EOF of a valid message on the CAN bus, the time stamp is written to the highest bytes (0x000E, 0x000F) in the appropriate buffer (see Section 10.3.3, "Programmer's Model of Message Storage"). The internal timer is reset (all bits set to 0) when disabled. This bit is held low in initialization mode. 0 Disable internal MSCAN timer 1 Enable internal MSCAN timer 2 WUPE4 Wake-Up Enable -- This configuration bit allows the MSCAN to restart from sleep mode when traffic on CAN is detected (see Section 10.4.5.4, "MSCAN Sleep Mode"). This bit must be configured before sleep mode entry for the selected function to take effect. 0 Wake-up disabled -- The MSCAN ignores traffic on CAN 1 Wake-up enabled -- The MSCAN is able to restart MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 425 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-1. CANCTL0 Register Field Descriptions (continued) Field Description 1 SLPRQ5 Sleep Mode Request -- This bit requests the MSCAN to enter sleep mode, which is an internal power saving mode (see Section 10.4.5.4, "MSCAN Sleep Mode"). The sleep mode request is serviced when the CAN bus is idle, i.e., the module is not receiving a message and all transmit buffers are empty. The module indicates entry to sleep mode by setting SLPAK = 1 (see Section 10.3.2.2, "MSCAN Control Register 1 (CANCTL1)"). SLPRQ cannot be set while the WUPIF flag is set (see Section 10.3.2.5, "MSCAN Receiver Flag Register (CANRFLG)"). Sleep mode will be active until SLPRQ is cleared by the CPU or, depending on the setting of WUPE, the MSCAN detects activity on the CAN bus and clears SLPRQ itself. 0 Running -- The MSCAN functions normally 1 Sleep mode request -- The MSCAN enters sleep mode when CAN bus idle 0 INITRQ6,7 Initialization Mode Request -- When this bit is set by the CPU, the MSCAN skips to initialization mode (see Section 10.4.5.5, "MSCAN Initialization Mode"). Any ongoing transmission or reception is aborted and synchronization to the CAN bus is lost. The module indicates entry to initialization mode by setting INITAK = 1 (Section 10.3.2.2, "MSCAN Control Register 1 (CANCTL1)"). The following registers enter their hard reset state and restore their default values: CANCTL08, CANRFLG9, CANRIER10, CANTFLG, CANTIER, CANTARQ, CANTAAK, and CANTBSEL. The registers CANCTL1, CANBTR0, CANBTR1, CANIDAC, CANIDAR0-7, and CANIDMR0-7 can only be written by the CPU when the MSCAN is in initialization mode (INITRQ = 1 and INITAK = 1). The values of the error counters are not affected by initialization mode. When this bit is cleared by the CPU, the MSCAN restarts and then tries to synchronize to the CAN bus. If the MSCAN is not in bus-off state, it synchronizes after 11 consecutive recessive bits on the CAN bus; if the MSCAN is in bus-off state, it continues to wait for 128 occurrences of 11 consecutive recessive bits. Writing to other bits in CANCTL0, CANRFLG, CANRIER, CANTFLG, or CANTIER must be done only after initialization mode is exited, which is INITRQ = 0 and INITAK = 0. 0 Normal operation 1 MSCAN in initialization mode 1 The MSCAN must be in normal mode for this bit to become set. See the Bosch CAN 2.0A/B specification for a detailed definition of transmitter and receiver states. 3 In order to protect from accidentally violating the CAN protocol, the TXCAN pin is immediately forced to a recessive state when the CPU enters wait (CSWAI = 1) or stop mode (see Section 10.4.5.2, "Operation in Wait Mode" and Section 10.4.5.3, "Operation in Stop Mode"). 4 The CPU has to make sure that the WUPE register and the WUPIE wake-up interrupt enable register (see Section 10.3.2.6, "MSCAN Receiver Interrupt Enable Register (CANRIER)) is enabled, if the recovery mechanism from stop or wait is required. 5 The CPU cannot clear SLPRQ before the MSCAN has entered sleep mode (SLPRQ = 1 and SLPAK = 1). 6 The CPU cannot clear INITRQ before the MSCAN has entered initialization mode (INITRQ = 1 and INITAK = 1). 7 In order to protect from accidentally violating the CAN protocol, the TXCAN pin is immediately forced to a recessive state when the initialization mode is requested by the CPU. Thus, the recommended procedure is to bring the MSCAN into sleep mode (SLPRQ = 1 and SLPAK = 1) before requesting initialization mode. 8 Not including WUPE, INITRQ, and SLPRQ. 9 TSTAT1 and TSTAT0 are not affected by initialization mode. 10 RSTAT1 and RSTAT0 are not affected by initialization mode. 2 10.3.2.2 MSCAN Control Register 1 (CANCTL1) The CANCTL1 register provides various control bits and handshake status information of the MSCAN module as described below. MC9S12XDP512 Data Sheet, Rev. 2.21 426 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 7 6 5 4 3 2 CANE CLKSRC LOOPB LISTEN BORM WUPM 0 0 0 1 0 0 R 1 0 SLPAK INITAK 0 1 W Reset: = Unimplemented Figure 10-5. MSCAN Control Register 1 (CANCTL1) Read: Anytime Write: Anytime when INITRQ = 1 and INITAK = 1, except CANE which is write once in normal and anytime in special system operation modes when the MSCAN is in initialization mode (INITRQ = 1 and INITAK = 1). Table 10-2. CANCTL1 Register Field Descriptions Field 7 CANE Description MSCAN Enable 0 MSCAN module is disabled 1 MSCAN module is enabled 6 CLKSRC MSCAN Clock Source -- This bit defines the clock source for the MSCAN module (only for systems with a clock generation module; Section 10.4.3.2, "Clock System," and Section Figure 10-43., "MSCAN Clocking Scheme,"). 0 MSCAN clock source is the oscillator clock 1 MSCAN clock source is the bus clock 5 LOOPB Loopback Self Test Mode -- When this bit is set, the MSCAN performs an internal loopback which can be used for self test operation. The bit stream output of the transmitter is fed back to the receiver internally. The RXCAN input pin is ignored and the TXCAN output goes to the recessive state (logic 1). The MSCAN behaves as it does normally when transmitting and treats its own transmitted message as a message received from a remote node. In this state, the MSCAN ignores the bit sent during the ACK slot in the CAN frame acknowledge field to ensure proper reception of its own message. Both transmit and receive interrupts are generated. 0 Loopback self test disabled 1 Loopback self test enabled 4 LISTEN Listen Only Mode -- This bit configures the MSCAN as a CAN bus monitor. When LISTEN is set, all valid CAN messages with matching ID are received, but no acknowledgement or error frames are sent out (see Section 10.4.4.4, "Listen-Only Mode"). In addition, the error counters are frozen. Listen only mode supports applications which require "hot plugging" or throughput analysis. The MSCAN is unable to transmit any messages when listen only mode is active. 0 Normal operation 1 Listen only mode activated 3 BORM Bus-Off Recovery Mode -- This bits configures the bus-off state recovery mode of the MSCAN. Refer to Section 10.5.2, "Bus-Off Recovery," for details. 0 Automatic bus-off recovery (see Bosch CAN 2.0A/B protocol specification) 1 Bus-off recovery upon user request 2 WUPM Wake-Up Mode -- If WUPE in CANCTL0 is enabled, this bit defines whether the integrated low-pass filter is applied to protect the MSCAN from spurious wake-up (see Section 10.4.5.4, "MSCAN Sleep Mode"). 0 MSCAN wakes up on any dominant level on the CAN bus 1 MSCAN wakes up only in case of a dominant pulse on the CAN bus that has a length of Twup MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 427 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-2. CANCTL1 Register Field Descriptions (continued) Field Description 1 SLPAK Sleep Mode Acknowledge -- This flag indicates whether the MSCAN module has entered sleep mode (see Section 10.4.5.4, "MSCAN Sleep Mode"). It is used as a handshake flag for the SLPRQ sleep mode request. Sleep mode is active when SLPRQ = 1 and SLPAK = 1. Depending on the setting of WUPE, the MSCAN will clear the flag if it detects activity on the CAN bus while in sleep mode. 0 Running -- The MSCAN operates normally 1 Sleep mode active -- The MSCAN has entered sleep mode 0 INITAK Initialization Mode Acknowledge -- This flag indicates whether the MSCAN module is in initialization mode (see Section 10.4.5.5, "MSCAN Initialization Mode"). It is used as a handshake flag for the INITRQ initialization mode request. Initialization mode is active when INITRQ = 1 and INITAK = 1. The registers CANCTL1, CANBTR0, CANBTR1, CANIDAC, CANIDAR0-CANIDAR7, and CANIDMR0-CANIDMR7 can be written only by the CPU when the MSCAN is in initialization mode. 0 Running -- The MSCAN operates normally 1 Initialization mode active -- The MSCAN has entered initialization mode 10.3.2.3 MSCAN Bus Timing Register 0 (CANBTR0) The CANBTR0 register configures various CAN bus timing parameters of the MSCAN module. 7 6 5 4 3 2 1 0 SJW1 SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 0 0 0 0 0 0 0 0 R W Reset: Figure 10-6. MSCAN Bus Timing Register 0 (CANBTR0) Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) Table 10-3. CANBTR0 Register Field Descriptions Field Description 7:6 SJW[1:0] Synchronization Jump Width -- The synchronization jump width defines the maximum number of time quanta (Tq) clock cycles a bit can be shortened or lengthened to achieve resynchronization to data transitions on the CAN bus (see Table 10-4). 5:0 BRP[5:0] Baud Rate Prescaler -- These bits determine the time quanta (Tq) clock which is used to build up the bit timing (see Table 10-5). Table 10-4. Synchronization Jump Width SJW1 SJW0 Synchronization Jump Width 0 0 1 Tq clock cycle 0 1 2 Tq clock cycles 1 0 3 Tq clock cycles 1 1 4 Tq clock cycles MC9S12XDP512 Data Sheet, Rev. 2.21 428 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-5. Baud Rate Prescaler 10.3.2.4 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 Prescaler value (P) 0 0 0 0 0 0 1 0 0 0 0 0 1 2 0 0 0 0 1 0 3 0 0 0 0 1 1 4 : : : : : : : 1 1 1 1 1 1 64 MSCAN Bus Timing Register 1 (CANBTR1) The CANBTR1 register configures various CAN bus timing parameters of the MSCAN module. 7 6 5 4 3 2 1 0 SAMP TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 0 0 0 0 0 0 0 0 R W Reset: Figure 10-7. MSCAN Bus Timing Register 1 (CANBTR1) Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) Table 10-6. CANBTR1 Register Field Descriptions Field Description 7 SAMP Sampling -- This bit determines the number of CAN bus samples taken per bit time. 0 One sample per bit. 1 Three samples per bit1. If SAMP = 0, the resulting bit value is equal to the value of the single bit positioned at the sample point. If SAMP = 1, the resulting bit value is determined by using majority rule on the three total samples. For higher bit rates, it is recommended that only one sample is taken per bit time (SAMP = 0). 6:4 Time Segment 2 -- Time segments within the bit time fix the number of clock cycles per bit time and the location TSEG2[2:0] of the sample point (see Figure 10-44). Time segment 2 (TSEG2) values are programmable as shown in Table 10-7. 3:0 Time Segment 1 -- Time segments within the bit time fix the number of clock cycles per bit time and the location TSEG1[3:0] of the sample point (see Figure 10-44). Time segment 1 (TSEG1) values are programmable as shown in Table 10-8. 1 In this case, PHASE_SEG1 must be at least 2 time quanta (Tq). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 429 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-7. Time Segment 2 Values 1 TSEG22 TSEG21 TSEG20 Time Segment 2 0 0 0 1 Tq clock cycle1 0 0 1 2 Tq clock cycles : : : : 1 1 0 7 Tq clock cycles 1 1 1 8 Tq clock cycles This setting is not valid. Please refer to Table 10-35 for valid settings. Table 10-8. Time Segment 1 Values 1 TSEG13 TSEG12 TSEG11 TSEG10 Time segment 1 0 0 0 0 1 Tq clock cycle1 0 0 0 1 2 Tq clock cycles1 0 0 1 0 3 Tq clock cycles1 0 0 1 1 4 Tq clock cycles : : : : : 1 1 1 0 15 Tq clock cycles 1 1 1 1 16 Tq clock cycles This setting is not valid. Please refer to Table 10-35 for valid settings. The bit time is determined by the oscillator frequency, the baud rate prescaler, and the number of time quanta (Tq) clock cycles per bit (as shown in Table 10-7 and Table 10-8). Eqn. 10-1 ( Prescaler value ) Bit Time = ------------------------------------------------------ * ( 1 + TimeSegment1 + TimeSegment2 ) f CANCLK 10.3.2.5 MSCAN Receiver Flag Register (CANRFLG) A flag can be cleared only by software (writing a 1 to the corresponding bit position) when the condition which caused the setting is no longer valid. Every flag has an associated interrupt enable bit in the CANRIER register. 7 6 WUPIF CSCIF 0 0 R 5 4 3 2 RSTAT1 RSTAT0 TSTAT1 TSTAT0 1 0 OVRIF RXF 0 0 W Reset: 0 0 0 0 = Unimplemented Figure 10-8. MSCAN Receiver Flag Register (CANRFLG) MC9S12XDP512 Data Sheet, Rev. 2.21 430 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) NOTE The CANRFLG register is held in the reset state1 when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable again as soon as the initialization mode is exited (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime when out of initialization mode, except RSTAT[1:0] and TSTAT[1:0] flags which are read-only; write of 1 clears flag; write of 0 is ignored. Table 10-9. CANRFLG Register Field Descriptions Field Description 7 WUPIF Wake-Up Interrupt Flag -- If the MSCAN detects CAN bus activity while in sleep mode (see Section 10.4.5.4, "MSCAN Sleep Mode,") and WUPE = 1 in CANTCTL0 (see Section 10.3.2.1, "MSCAN Control Register 0 (CANCTL0)"), the module will set WUPIF. If not masked, a wake-up interrupt is pending while this flag is set. 0 No wake-up activity observed while in sleep mode 1 MSCAN detected activity on the CAN bus and requested wake-up 6 CSCIF CAN Status Change Interrupt Flag -- This flag is set when the MSCAN changes its current CAN bus status due to the actual value of the transmit error counter (TEC) and the receive error counter (REC). An additional 4-bit (RSTAT[1:0], TSTAT[1:0]) status register, which is split into separate sections for TEC/REC, informs the system on the actual CAN bus status (see Section 10.3.2.6, "MSCAN Receiver Interrupt Enable Register (CANRIER)"). If not masked, an error interrupt is pending while this flag is set. CSCIF provides a blocking interrupt. That guarantees that the receiver/transmitter status bits (RSTAT/TSTAT) are only updated when no CAN status change interrupt is pending. If the TECs/RECs change their current value after the CSCIF is asserted, which would cause an additional state change in the RSTAT/TSTAT bits, these bits keep their status until the current CSCIF interrupt is cleared again. 0 No change in CAN bus status occurred since last interrupt 1 MSCAN changed current CAN bus status 5:4 RSTAT[1:0] Receiver Status Bits -- The values of the error counters control the actual CAN bus status of the MSCAN. As soon as the status change interrupt flag (CSCIF) is set, these bits indicate the appropriate receiver related CAN bus status of the MSCAN. The coding for the bits RSTAT1, RSTAT0 is: 00 RxOK: 0 receive error counter 96 01 RxWRN: 96 < receive error counter 127 10 RxERR: 127 < receive error counter 11 Bus-off1: transmit error counter > 255 3:2 TSTAT[1:0] Transmitter Status Bits -- The values of the error counters control the actual CAN bus status of the MSCAN. As soon as the status change interrupt flag (CSCIF) is set, these bits indicate the appropriate transmitter related CAN bus status of the MSCAN. The coding for the bits TSTAT1, TSTAT0 is: 00 TxOK: 0 transmit error counter 96 01 TxWRN: 96 < transmit error counter 127 10 TxERR: 127 < transmit error counter 255 11 Bus-Off: transmit error counter > 255 1. The RSTAT[1:0], TSTAT[1:0] bits are not affected by initialization mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 431 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-9. CANRFLG Register Field Descriptions (continued) Field Description 1 OVRIF Overrun Interrupt Flag -- This flag is set when a data overrun condition occurs. If not masked, an error interrupt is pending while this flag is set. 0 No data overrun condition 1 A data overrun detected 0 RXF2 Receive Buffer Full Flag -- RXF is set by the MSCAN when a new message is shifted in the receiver FIFO. This flag indicates whether the shifted buffer is loaded with a correctly received message (matching identifier, matching cyclic redundancy code (CRC) and no other errors detected). After the CPU has read that message from the RxFG buffer in the receiver FIFO, the RXF flag must be cleared to release the buffer. A set RXF flag prohibits the shifting of the next FIFO entry into the foreground buffer (RxFG). If not masked, a receive interrupt is pending while this flag is set. 0 No new message available within the RxFG 1 The receiver FIFO is not empty. A new message is available in the RxFG 1 Redundant Information for the most critical CAN bus status which is "bus-off". This only occurs if the Tx error counter exceeds a number of 255 errors. Bus-off affects the receiver state. As soon as the transmitter leaves its bus-off state the receiver state skips to RxOK too. Refer also to TSTAT[1:0] coding in this register. 2 To ensure data integrity, do not read the receive buffer registers while the RXF flag is cleared. For MCUs with dual CPUs, reading the receive buffer registers while the RXF flag is cleared may result in a CPU fault condition. 10.3.2.6 MSCAN Receiver Interrupt Enable Register (CANRIER) This register contains the interrupt enable bits for the interrupt flags described in the CANRFLG register. 7 6 5 4 3 2 1 0 WUPIE CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 0 0 0 0 R W Reset: Figure 10-9. MSCAN Receiver Interrupt Enable Register (CANRIER) NOTE The CANRIER register is held in the reset state when the initialization mode is active (INITRQ=1 and INITAK=1). This register is writable when not in initialization mode (INITRQ=0 and INITAK=0). The RSTATE[1:0], TSTATE[1:0] bits are not affected by initialization mode. Read: Anytime Write: Anytime when not in initialization mode MC9S12XDP512 Data Sheet, Rev. 2.21 432 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-10. CANRIER Register Field Descriptions Field 7 WUPIE1 6 CSCIE Description Wake-Up Interrupt Enable 0 No interrupt request is generated from this event. 1 A wake-up event causes a Wake-Up interrupt request. CAN Status Change Interrupt Enable 0 No interrupt request is generated from this event. 1 A CAN Status Change event causes an error interrupt request. 5:4 Receiver Status Change Enable -- These RSTAT enable bits control the sensitivity level in which receiver state RSTATE[1:0] changes are causing CSCIF interrupts. Independent of the chosen sensitivity level the RSTAT flags continue to indicate the actual receiver state and are only updated if no CSCIF interrupt is pending. 00 Do not generate any CSCIF interrupt caused by receiver state changes. 01 Generate CSCIF interrupt only if the receiver enters or leaves "bus-off" state. Discard other receiver state changes for generating CSCIF interrupt. 10 Generate CSCIF interrupt only if the receiver enters or leaves "RxErr" or "bus-off"2 state. Discard other receiver state changes for generating CSCIF interrupt. 11 Generate CSCIF interrupt on all state changes. 3:2 Transmitter Status Change Enable -- These TSTAT enable bits control the sensitivity level in which transmitter TSTATE[1:0] state changes are causing CSCIF interrupts. Independent of the chosen sensitivity level, the TSTAT flags continue to indicate the actual transmitter state and are only updated if no CSCIF interrupt is pending. 00 Do not generate any CSCIF interrupt caused by transmitter state changes. 01 Generate CSCIF interrupt only if the transmitter enters or leaves "bus-off" state. Discard other transmitter state changes for generating CSCIF interrupt. 10 Generate CSCIF interrupt only if the transmitter enters or leaves "TxErr" or "bus-off" state. Discard other transmitter state changes for generating CSCIF interrupt. 11 Generate CSCIF interrupt on all state changes. 1 OVRIE Overrun Interrupt Enable 0 No interrupt request is generated from this event. 1 An overrun event causes an error interrupt request. 0 RXFIE Receiver Full Interrupt Enable 0 No interrupt request is generated from this event. 1 A receive buffer full (successful message reception) event causes a receiver interrupt request. 1 WUPIE and WUPE (see Section 10.3.2.1, "MSCAN Control Register 0 (CANCTL0)") must both be enabled if the recovery mechanism from stop or wait is required. 2 Bus-off state is defined by the CAN standard (see Bosch CAN 2.0A/B protocol specification: for only transmitters. Because the only possible state change for the transmitter from bus-off to TxOK also forces the receiver to skip its current state to RxOK, the coding of the RXSTAT[1:0] flags define an additional bus-off state for the receiver (see Section 10.3.2.5, "MSCAN Receiver Flag Register (CANRFLG)"). 10.3.2.7 MSCAN Transmitter Flag Register (CANTFLG) The transmit buffer empty flags each have an associated interrupt enable bit in the CANTIER register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 433 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) R 7 6 5 4 3 0 0 0 0 0 2 1 0 TXE2 TXE1 TXE0 1 1 1 W Reset: 0 0 0 0 0 = Unimplemented Figure 10-10. MSCAN Transmitter Flag Register (CANTFLG) NOTE The CANTFLG register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime for TXEx flags when not in initialization mode; write of 1 clears flag, write of 0 is ignored Table 10-11. CANTFLG Register Field Descriptions Field Description 2:0 TXE[2:0] Transmitter Buffer Empty -- This flag indicates that the associated transmit message buffer is empty, and thus not scheduled for transmission. The CPU must clear the flag after a message is set up in the transmit buffer and is due for transmission. The MSCAN sets the flag after the message is sent successfully. The flag is also set by the MSCAN when the transmission request is successfully aborted due to a pending abort request (see Section 10.3.2.9, "MSCAN Transmitter Message Abort Request Register (CANTARQ)"). If not masked, a transmit interrupt is pending while this flag is set. Clearing a TXEx flag also clears the corresponding ABTAKx (see Section 10.3.2.10, "MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK)"). When a TXEx flag is set, the corresponding ABTRQx bit is cleared (see Section 10.3.2.9, "MSCAN Transmitter Message Abort Request Register (CANTARQ)"). When listen-mode is active (see Section 10.3.2.2, "MSCAN Control Register 1 (CANCTL1)") the TXEx flags cannot be cleared and no transmission is started. Read and write accesses to the transmit buffer will be blocked, if the corresponding TXEx bit is cleared (TXEx = 0) and the buffer is scheduled for transmission. 0 The associated message buffer is full (loaded with a message due for transmission) 1 The associated message buffer is empty (not scheduled) 10.3.2.8 MSCAN Transmitter Interrupt Enable Register (CANTIER) This register contains the interrupt enable bits for the transmit buffer empty interrupt flags. R 7 6 5 4 3 0 0 0 0 0 2 1 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 W Reset: 0 0 0 0 0 = Unimplemented Figure 10-11. MSCAN Transmitter Interrupt Enable Register (CANTIER) MC9S12XDP512 Data Sheet, Rev. 2.21 434 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) NOTE The CANTIER register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime when not in initialization mode Table 10-12. CANTIER Register Field Descriptions Field Description 2:0 TXEIE[2:0] 10.3.2.9 Transmitter Empty Interrupt Enable 0 No interrupt request is generated from this event. 1 A transmitter empty (transmit buffer available for transmission) event causes a transmitter empty interrupt request. MSCAN Transmitter Message Abort Request Register (CANTARQ) The CANTARQ register allows abort request of queued messages as described below. R 7 6 5 4 3 0 0 0 0 0 2 1 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 W Reset: 0 0 0 0 0 = Unimplemented Figure 10-12. MSCAN Transmitter Message Abort Request Register (CANTARQ) NOTE The CANTARQ register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Anytime Write: Anytime when not in initialization mode Table 10-13. CANTARQ Register Field Descriptions Field Description 2:0 Abort Request -- The CPU sets the ABTRQx bit to request that a scheduled message buffer (TXEx = 0) be ABTRQ[2:0] aborted. The MSCAN grants the request if the message has not already started transmission, or if the transmission is not successful (lost arbitration or error). When a message is aborted, the associated TXE (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)") and abort acknowledge flags (ABTAK, see Section 10.3.2.10, "MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK)") are set and a transmit interrupt occurs if enabled. The CPU cannot reset ABTRQx. ABTRQx is reset whenever the associated TXE flag is set. 0 No abort request 1 Abort request pending MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 435 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.3.2.10 MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK) The CANTAAK register indicates the successful abort of a queued message, if requested by the appropriate bits in the CANTARQ register. R 7 6 5 4 3 2 1 0 0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 0 0 0 0 W Reset: = Unimplemented Figure 10-13. MSCAN Transmitter Message Abort Acknowledge Register (CANTAAK) NOTE The CANTAAK register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK = 1). Read: Anytime Write: Unimplemented for ABTAKx flags Table 10-14. CANTAAK Register Field Descriptions Field Description 2:0 Abort Acknowledge -- This flag acknowledges that a message was aborted due to a pending abort request ABTAK[2:0] from the CPU. After a particular message buffer is flagged empty, this flag can be used by the application software to identify whether the message was aborted successfully or was sent anyway. The ABTAKx flag is cleared whenever the corresponding TXE flag is cleared. 0 The message was not aborted. 1 The message was aborted. 10.3.2.11 MSCAN Transmit Buffer Selection Register (CANTBSEL) The CANTBSEL register allows the selection of the actual transmit message buffer, which then will be accessible in the CANTXFG register space. R 7 6 5 4 3 0 0 0 0 0 2 1 0 TX2 TX1 TX0 0 0 0 W Reset: 0 0 0 0 0 = Unimplemented Figure 10-14. MSCAN Transmit Buffer Selection Register (CANTBSEL) MC9S12XDP512 Data Sheet, Rev. 2.21 436 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) NOTE The CANTBSEL register is held in the reset state when the initialization mode is active (INITRQ = 1 and INITAK=1). This register is writable when not in initialization mode (INITRQ = 0 and INITAK = 0). Read: Find the lowest ordered bit set to 1, all other bits will be read as 0 Write: Anytime when not in initialization mode Table 10-15. CANTBSEL Register Field Descriptions Field Description 2:0 TX[2:0] Transmit Buffer Select -- The lowest numbered bit places the respective transmit buffer in the CANTXFG register space (e.g., TX1 = 1 and TX0 = 1 selects transmit buffer TX0; TX1 = 1 and TX0 = 0 selects transmit buffer TX1). Read and write accesses to the selected transmit buffer will be blocked, if the corresponding TXEx bit is cleared and the buffer is scheduled for transmission (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)"). 0 The associated message buffer is deselected 1 The associated message buffer is selected, if lowest numbered bit The following gives a short programming example of the usage of the CANTBSEL register: To get the next available transmit buffer, application software must read the CANTFLG register and write this value back into the CANTBSEL register. In this example Tx buffers TX1 and TX2 are available. The value read from CANTFLG is therefore 0b0000_0110. When writing this value back to CANTBSEL, the Tx buffer TX1 is selected in the CANTXFG because the lowest numbered bit set to 1 is at bit position 1. Reading back this value out of CANTBSEL results in 0b0000_0010, because only the lowest numbered bit position set to 1 is presented. This mechanism eases the application software the selection of the next available Tx buffer. * LDD CANTFLG; value read is 0b0000_0110 * STD CANTBSEL; value written is 0b0000_0110 * LDD CANTBSEL; value read is 0b0000_0010 If all transmit message buffers are deselected, no accesses are allowed to the CANTXFG registers. 10.3.2.12 MSCAN Identifier Acceptance Control Register (CANIDAC) The CANIDAC register is used for identifier acceptance control as described below. R 7 6 0 0 5 4 IDAM1 IDAM0 0 0 3 2 1 0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 W Reset: 0 0 = Unimplemented Figure 10-15. MSCAN Identifier Acceptance Control Register (CANIDAC) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 437 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1), except bits IDHITx, which are read-only Table 10-16. CANIDAC Register Field Descriptions Field Description 5:4 IDAM[1:0] Identifier Acceptance Mode -- The CPU sets these flags to define the identifier acceptance filter organization (see Section 10.4.3, "Identifier Acceptance Filter"). Table 10-17 summarizes the different settings. In filter closed mode, no message is accepted such that the foreground buffer is never reloaded. 2:0 IDHIT[2:0] Identifier Acceptance Hit Indicator -- The MSCAN sets these flags to indicate an identifier acceptance hit (see Section 10.4.3, "Identifier Acceptance Filter"). Table 10-18 summarizes the different settings. Table 10-17. Identifier Acceptance Mode Settings IDAM1 IDAM0 Identifier Acceptance Mode 0 0 Two 32-bit acceptance filters 0 1 Four 16-bit acceptance filters 1 0 Eight 8-bit acceptance filters 1 1 Filter closed Table 10-18. Identifier Acceptance Hit Indication IDHIT2 IDHIT1 IDHIT0 Identifier Acceptance Hit 0 0 0 Filter 0 hit 0 0 1 Filter 1 hit 0 1 0 Filter 2 hit 0 1 1 Filter 3 hit 1 0 0 Filter 4 hit 1 0 1 Filter 5 hit 1 1 0 Filter 6 hit 1 1 1 Filter 7 hit The IDHITx indicators are always related to the message in the foreground buffer (RxFG). When a message gets shifted into the foreground buffer of the receiver FIFO the indicators are updated as well. 10.3.2.13 MSCAN Reserved Register This register is reserved for factory testing of the MSCAN module and is not available in normal system operation modes. MC9S12XDP512 Data Sheet, Rev. 2.21 438 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset: = Unimplemented Figure 10-16. MSCAN Reserved Register Read: Always read 0x0000 in normal system operation modes Write: Unimplemented in normal system operation modes NOTE Writing to this register when in special modes can alter the MSCAN functionality. 10.3.2.14 MSCAN Miscellaneous Register (CANMISC) This register provides additional features. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 BOHOLD W Reset: 0 0 0 0 0 0 0 0 = Unimplemented Figure 10-17. MSCAN Miscellaneous Register (CANMISC) Read: Anytime Write: Anytime; write of `1' clears flag; write of `0' ignored Table 10-19. CANMISC Register Field Descriptions Field 0 BOHOLD Description Bus-off State Hold Until User Request -- If BORM is set in Section 10.3.2.2, "MSCAN Control Register 1 (CANCTL1), this bit indicates whether the module has entered the bus-off state. Clearing this bit requests the recovery from bus-off. Refer to Section 10.5.2, "Bus-Off Recovery," for details. 0 Module is not bus-off or recovery has been requested by user in bus-off state 1 Module is bus-off and holds this state until user request 10.3.2.15 MSCAN Receive Error Counter (CANRXERR) This register reflects the status of the MSCAN receive error counter. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 439 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) R 7 6 5 4 3 2 1 0 RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 0 0 0 0 0 0 0 0 W Reset: = Unimplemented Figure 10-18. MSCAN Receive Error Counter (CANRXERR) Read: Only when in sleep mode (SLPRQ = 1 and SLPAK = 1) or initialization mode (INITRQ = 1 and INITAK = 1) Write: Unimplemented NOTE Reading this register when in any other mode other than sleep or initialization mode may return an incorrect value. For MCUs with dual CPUs, this may result in a CPU fault condition. Writing to this register when in special modes can alter the MSCAN functionality. 10.3.2.16 MSCAN Transmit Error Counter (CANTXERR) This register reflects the status of the MSCAN transmit error counter. R 7 6 5 4 3 2 1 0 TXERR7 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 0 0 0 0 0 0 0 0 W Reset: = Unimplemented Figure 10-19. MSCAN Transmit Error Counter (CANTXERR) Read: Only when in sleep mode (SLPRQ = 1 and SLPAK = 1) or initialization mode (INITRQ = 1 and INITAK = 1) Write: Unimplemented NOTE Reading this register when in any other mode other than sleep or initialization mode, may return an incorrect value. For MCUs with dual CPUs, this may result in a CPU fault condition. Writing to this register when in special modes can alter the MSCAN functionality. MC9S12XDP512 Data Sheet, Rev. 2.21 440 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.3.2.17 MSCAN Identifier Acceptance Registers (CANIDAR0-7) On reception, each message is written into the background receive buffer. The CPU is only signalled to read the message if it passes the criteria in the identifier acceptance and identifier mask registers (accepted); otherwise, the message is overwritten by the next message (dropped). The acceptance registers of the MSCAN are applied on the IDR0-IDR3 registers (see Section 10.3.3.1, "Identifier Registers (IDR0-IDR3)") of incoming messages in a bit by bit manner (see Section 10.4.3, "Identifier Acceptance Filter"). For extended identifiers, all four acceptance and mask registers are applied. For standard identifiers, only the first two (CANIDAR0/1, CANIDMR0/1) are applied. Module Base + 0x0010 (CANIDAR0) 0x0011 (CANIDAR1) 0x0012 (CANIDAR2) 0x0013 (CANIDAR3) 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 R W Reset R W Reset R W Reset R W Reset Figure 10-20. MSCAN Identifier Acceptance Registers (First Bank) -- CANIDAR0-CANIDAR3 Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 441 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-20. CANIDAR0-CANIDAR3 Register Field Descriptions Field Description 7:0 AC[7:0] Acceptance Code Bits -- AC[7:0] comprise a user-defined sequence of bits with which the corresponding bits of the related identifier register (IDRn) of the receive message buffer are compared. The result of this comparison is then masked with the corresponding identifier mask register. Module Base + 0x0018 (CANIDAR4) 0x0019 (CANIDAR5) 0x001A (CANIDAR6) 0x001B (CANIDAR7) 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 0 0 0 0 0 0 0 0 R W Reset R W Reset R W Reset R W Reset Figure 10-21. MSCAN Identifier Acceptance Registers (Second Bank) -- CANIDAR4-CANIDAR7 Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) MC9S12XDP512 Data Sheet, Rev. 2.21 442 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-21. CANIDAR4-CANIDAR7 Register Field Descriptions Field Description 7:0 AC[7:0] Acceptance Code Bits -- AC[7:0] comprise a user-defined sequence of bits with which the corresponding bits of the related identifier register (IDRn) of the receive message buffer are compared. The result of this comparison is then masked with the corresponding identifier mask register. 10.3.2.18 MSCAN Identifier Mask Registers (CANIDMR0-CANIDMR7) The identifier mask register specifies which of the corresponding bits in the identifier acceptance register are relevant for acceptance filtering. To receive standard identifiers in 32 bit filter mode, it is required to program the last three bits (AM[2:0]) in the mask registers CANIDMR1 and CANIDMR5 to "don't care." To receive standard identifiers in 16 bit filter mode, it is required to program the last three bits (AM[2:0]) in the mask registers CANIDMR1, CANIDMR3, CANIDMR5, and CANIDMR7 to "don't care." Module Base + 0x0014 (CANIDMR0) 0x0015 (CANIDMR1) 0x0016 (CANIDMR2) 0x0017 (CANIDMR3) 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 R W Reset R W Reset R W Reset R W Reset Figure 10-22. MSCAN Identifier Mask Registers (First Bank) -- CANIDMR0-CANIDMR3 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 443 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) Table 10-22. CANIDMR0-CANIDMR3 Register Field Descriptions Field Description 7:0 AM[7:0] Acceptance Mask Bits -- If a particular bit in this register is cleared, this indicates that the corresponding bit in the identifier acceptance register must be the same as its identifier bit before a match is detected. The message is accepted if all such bits match. If a bit is set, it indicates that the state of the corresponding bit in the identifier acceptance register does not affect whether or not the message is accepted. 0 Match corresponding acceptance code register and identifier bits 1 Ignore corresponding acceptance code register bit Module Base + 0x001C (CANIDMR4) 0x001D (CANIDMR5) 0x001E (CANIDMR6) 0x001F (CANIDMR7) 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 7 6 5 4 3 2 1 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 0 0 0 0 0 0 0 R W Reset R W Reset R W Reset R W Reset Figure 10-23. MSCAN Identifier Mask Registers (Second Bank) -- CANIDMR4-CANIDMR7 Read: Anytime Write: Anytime in initialization mode (INITRQ = 1 and INITAK = 1) MC9S12XDP512 Data Sheet, Rev. 2.21 444 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-23. CANIDMR4-CANIDMR7 Register Field Descriptions Field Description 7:0 AM[7:0] Acceptance Mask Bits -- If a particular bit in this register is cleared, this indicates that the corresponding bit in the identifier acceptance register must be the same as its identifier bit before a match is detected. The message is accepted if all such bits match. If a bit is set, it indicates that the state of the corresponding bit in the identifier acceptance register does not affect whether or not the message is accepted. 0 Match corresponding acceptance code register and identifier bits 1 Ignore corresponding acceptance code register bit 10.3.3 Programmer's Model of Message Storage The following section details the organization of the receive and transmit message buffers and the associated control registers. To simplify the programmer interface, the receive and transmit message buffers have the same outline. Each message buffer allocates 16 bytes in the memory map containing a 13 byte data structure. An additional transmit buffer priority register (TBPR) is defined for the transmit buffers. Within the last two bytes of this memory map, the MSCAN stores a special 16-bit time stamp, which is sampled from an internal timer after successful transmission or reception of a message. This feature is only available for transmit and receiver buffers, if the TIME bit is set (see Section 10.3.2.1, "MSCAN Control Register 0 (CANCTL0)"). The time stamp register is written by the MSCAN. The CPU can only read these registers. Table 10-24. Message Buffer Organization Offset Address Register 0x00X0 Identifier Register 0 0x00X1 Identifier Register 1 0x00X2 Identifier Register 2 0x00X3 Identifier Register 3 0x00X4 Data Segment Register 0 0x00X5 Data Segment Register 1 0x00X6 Data Segment Register 2 0x00X7 Data Segment Register 3 0x00X8 Data Segment Register 4 0x00X9 Data Segment Register 5 0x00XA Data Segment Register 6 0x00XB Data Segment Register 7 0x00XC Data Length Register 0x00XD Transmit Buffer Priority Register1 0x00XE Time Stamp Register (High Byte)2 0x00XF Time Stamp Register (Low Byte)3 Access MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 445 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 1 Not applicable for receive buffers Read-only for CPU 3 Read-only for CPU 2 Figure 10-24 shows the common 13-byte data structure of receive and transmit buffers for extended identifiers. The mapping of standard identifiers into the IDR registers is shown in Figure 10-25. All bits of the receive and transmit buffers are `x' out of reset because of RAM-based implementation1. All reserved or unused bits of the receive and transmit buffers always read `x'. 1. Exception: The transmit priority registers are 0 out of reset. MC9S12XDP512 Data Sheet, Rev. 2.21 446 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 447 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Figure 10-24. Receive/Transmit Message Buffer -- Extended Identifier Mapping Register Name Bit 7 6 5 4 3 2 1 Bit0 ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21 R IDR0 W MC9S12XDP512 Data Sheet, Rev. 2.21 448 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Figure 10-24. Receive/Transmit Message Buffer -- Extended Identifier Mapping Register Name Bit 7 6 5 4 3 2 1 Bit0 ID20 ID19 ID18 SRR (=1) IDE (=1) ID17 ID16 ID15 ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DLC3 DLC2 DLC1 DLC0 R IDR1 W R IDR2 W R IDR3 W R DSR0 W R DSR1 W R DSR2 W R DSR3 W R DSR4 W R DSR5 W R DSR6 W R DSR7 W R DLR W = Unused, always read `x' MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 449 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Read: For transmit buffers, anytime when TXEx flag is set (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 10.3.2.11, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). For receive buffers, only when RXF flag is set (see Section 10.3.2.5, "MSCAN Receiver Flag Register (CANRFLG)"). Write: For transmit buffers, anytime when TXEx flag is set (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 10.3.2.11, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). Unimplemented for receive buffers. Reset: Undefined (0x00XX) because of RAM-based implementation Figure 10-25. Receive/Transmit Message Buffer -- Standard Identifier Mapping Register Name Bit 7 6 5 4 3 2 1 Bit 0 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR IDE (=0) R IDR0 W R IDR1 W R IDR2 W R IDR3 W = Unused, always read `x' 10.3.3.1 Identifier Registers (IDR0-IDR3) The identifier registers for an extended format identifier consist of a total of 32 bits; ID[28:0], SRR, IDE, and RTR bits. The identifier registers for a standard format identifier consist of a total of 13 bits; ID[10:0], RTR, and IDE bits. 10.3.3.1.1 IDR0-IDR3 for Extended Identifier Mapping 7 6 5 4 3 2 1 0 ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21 x x x x x x x x R W Reset: Figure 10-26. Identifier Register 0 (IDR0) -- Extended Identifier Mapping MC9S12XDP512 Data Sheet, Rev. 2.21 450 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-25. IDR0 Register Field Descriptions -- Extended Field Description 7:0 ID[28:21] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. 7 6 5 4 3 2 1 0 ID20 ID19 ID18 SRR (=1) IDE (=1) ID17 ID16 ID15 x x x x x x x x R W Reset: Figure 10-27. Identifier Register 1 (IDR1) -- Extended Identifier Mapping Table 10-26. IDR1 Register Field Descriptions -- Extended Field Description 7:5 ID[20:18] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. 4 SRR Substitute Remote Request -- This fixed recessive bit is used only in extended format. It must be set to 1 by the user for transmission buffers and is stored as received on the CAN bus for receive buffers. 3 IDE ID Extended -- This flag indicates whether the extended or standard identifier format is applied in this buffer. In the case of a receive buffer, the flag is set as received and indicates to the CPU how to process the buffer identifier registers. In the case of a transmit buffer, the flag indicates to the MSCAN what type of identifier to send. 0 Standard format (11 bit) 1 Extended format (29 bit) 2:0 ID[17:15] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. 7 6 5 4 3 2 1 0 ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7 x x x x x x x x R W Reset: Figure 10-28. Identifier Register 2 (IDR2) -- Extended Identifier Mapping Table 10-27. IDR2 Register Field Descriptions -- Extended Field Description 7:0 ID[14:7] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 451 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 7 6 5 4 3 2 1 0 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR x x x x x x x x R W Reset: Figure 10-29. Identifier Register 3 (IDR3) -- Extended Identifier Mapping Table 10-28. IDR3 Register Field Descriptions -- Extended Field Description 7:1 ID[6:0] Extended Format Identifier -- The identifiers consist of 29 bits (ID[28:0]) for the extended format. ID28 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. 0 RTR Remote Transmission Request -- This flag reflects the status of the remote transmission request bit in the CAN frame. In the case of a receive buffer, it indicates the status of the received frame and supports the transmission of an answering frame in software. In the case of a transmit buffer, this flag defines the setting of the RTR bit to be sent. 0 Data frame 1 Remote frame 10.3.3.1.2 IDR0-IDR3 for Standard Identifier Mapping 7 6 5 4 3 2 1 0 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 x x x x x x x x R W Reset: Figure 10-30. Identifier Register 0 -- Standard Mapping Table 10-29. IDR0 Register Field Descriptions -- Standard Field Description 7:0 ID[10:3] Standard Format Identifier -- The identifiers consist of 11 bits (ID[10:0]) for the standard format. ID10 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. See also ID bits in Table 10-30. 7 6 5 4 3 ID2 ID1 ID0 RTR IDE (=0) x x x x x 2 1 0 x x x R W Reset: = Unused; always read `x' Figure 10-31. Identifier Register 1 -- Standard Mapping MC9S12XDP512 Data Sheet, Rev. 2.21 452 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-30. IDR1 Register Field Descriptions Field Description 7:5 ID[2:0] Standard Format Identifier -- The identifiers consist of 11 bits (ID[10:0]) for the standard format. ID10 is the most significant bit and is transmitted first on the CAN bus during the arbitration procedure. The priority of an identifier is defined to be highest for the smallest binary number. See also ID bits in Table 10-29. 4 RTR Remote Transmission Request -- This flag reflects the status of the Remote Transmission Request bit in the CAN frame. In the case of a receive buffer, it indicates the status of the received frame and supports the transmission of an answering frame in software. In the case of a transmit buffer, this flag defines the setting of the RTR bit to be sent. 0 Data frame 1 Remote frame 3 IDE ID Extended -- This flag indicates whether the extended or standard identifier format is applied in this buffer. In the case of a receive buffer, the flag is set as received and indicates to the CPU how to process the buffer identifier registers. In the case of a transmit buffer, the flag indicates to the MSCAN what type of identifier to send. 0 Standard format (11 bit) 1 Extended format (29 bit) 7 6 5 4 3 2 1 0 x x x x x x x x R W Reset: = Unused; always read `x' Figure 10-32. Identifier Register 2 -- Standard Mapping 7 6 5 4 3 2 1 0 x x x x x x x x R W Reset: = Unused; always read `x' Figure 10-33. Identifier Register 3 -- Standard Mapping 10.3.3.2 Data Segment Registers (DSR0-7) The eight data segment registers, each with bits DB[7:0], contain the data to be transmitted or received. The number of bytes to be transmitted or received is determined by the data length code in the corresponding DLR register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 453 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Module Base + 0x0004 (DSR0) 0x0005 (DSR1) 0x0006 (DSR2) 0x0007 (DSR3) 0x0008 (DSR4) 0x0009 (DSR5) 0x000A (DSR6) 0x000B (DSR7) 7 6 5 4 3 2 1 0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 x x x x x x x x R W Reset: Figure 10-34. Data Segment Registers (DSR0-DSR7) -- Extended Identifier Mapping Table 10-31. DSR0-DSR7 Register Field Descriptions Field Description 7:0 DB[7:0] Data bits 7:0 10.3.3.3 Data Length Register (DLR) This register keeps the data length field of the CAN frame. 7 6 5 4 3 2 1 0 DLC3 DLC2 DLC1 DLC0 x x x x R W Reset: x x x x = Unused; always read "x" Figure 10-35. Data Length Register (DLR) -- Extended Identifier Mapping Table 10-32. DLR Register Field Descriptions Field Description 3:0 DLC[3:0] Data Length Code Bits -- The data length code contains the number of bytes (data byte count) of the respective message. During the transmission of a remote frame, the data length code is transmitted as programmed while the number of transmitted data bytes is always 0. The data byte count ranges from 0 to 8 for a data frame. Table 10-33 shows the effect of setting the DLC bits. MC9S12XDP512 Data Sheet, Rev. 2.21 454 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-33. Data Length Codes Data Length Code 10.3.3.4 DLC3 DLC2 DLC1 DLC0 Data Byte Count 0 0 0 0 0 0 0 0 1 1 0 0 1 0 2 0 0 1 1 3 0 1 0 0 4 0 1 0 1 5 0 1 1 0 6 0 1 1 1 7 1 0 0 0 8 Transmit Buffer Priority Register (TBPR) This register defines the local priority of the associated message buffer. The local priority is used for the internal prioritization process of the MSCAN and is defined to be highest for the smallest binary number. The MSCAN implements the following internal prioritization mechanisms: * All transmission buffers with a cleared TXEx flag participate in the prioritization immediately before the SOF (start of frame) is sent. * The transmission buffer with the lowest local priority field wins the prioritization. In cases of more than one buffer having the same lowest priority, the message buffer with the lower index number wins. 7 6 5 4 3 2 1 0 PRIO7 PRIO6 PRIO5 PRIO4 PRIO3 PRIO2 PRIO1 PRIO0 0 0 0 0 0 0 0 0 R W Reset: Figure 10-36. Transmit Buffer Priority Register (TBPR) Read: Anytime when TXEx flag is set (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 10.3.2.11, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). Write: Anytime when TXEx flag is set (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 10.3.2.11, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). 10.3.3.5 Time Stamp Register (TSRH-TSRL) If the TIME bit is enabled, the MSCAN will write a time stamp to the respective registers in the active transmit or receive buffer right after the EOF of a valid message on the CAN bus (see Section 10.3.2.1, MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 455 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) "MSCAN Control Register 0 (CANCTL0)"). In case of a transmission, the CPU can only read the time stamp after the respective transmit buffer has been flagged empty. The timer value, which is used for stamping, is taken from a free running internal CAN bit clock. A timer overrun is not indicated by the MSCAN. The timer is reset (all bits set to 0) during initialization mode. The CPU can only read the time stamp registers. R 7 6 5 4 3 2 1 0 TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8 x x x x x x x x W Reset: Figure 10-37. Time Stamp Register -- High Byte (TSRH) R 7 6 5 4 3 2 1 0 TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0 x x x x x x x x W Reset: Figure 10-38. Time Stamp Register -- Low Byte (TSRL) Read: Anytime when TXEx flag is set (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)") and the corresponding transmit buffer is selected in CANTBSEL (see Section 10.3.2.11, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). Write: Unimplemented 10.4 10.4.1 Functional Description General This section provides a complete functional description of the MSCAN. It describes each of the features and modes listed in the introduction. MC9S12XDP512 Data Sheet, Rev. 2.21 456 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.4.2 Message Storage CAN Receive / Transmit Engine CPU12 Memory Mapped I/O Rx0 RXF Receiver TxBG Tx0 MSCAN TxFG Tx1 TxBG Tx2 Transmitter CPU bus RxFG RxBG MSCAN Rx1 Rx2 Rx3 Rx4 TXE0 PRIO TXE1 CPU bus PRIO TXE2 PRIO Figure 10-39. User Model for Message Buffer Organization MSCAN facilitates a sophisticated message storage system which addresses the requirements of a broad range of network applications. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 457 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.4.2.1 Message Transmit Background Modern application layer software is built upon two fundamental assumptions: * Any CAN node is able to send out a stream of scheduled messages without releasing the CAN bus between the two messages. Such nodes arbitrate for the CAN bus immediately after sending the previous message and only release the CAN bus in case of lost arbitration. * The internal message queue within any CAN node is organized such that the highest priority message is sent out first, if more than one message is ready to be sent. The behavior described in the bullets above cannot be achieved with a single transmit buffer. That buffer must be reloaded immediately after the previous message is sent. This loading process lasts a finite amount of time and must be completed within the inter-frame sequence (IFS) to be able to send an uninterrupted stream of messages. Even if this is feasible for limited CAN bus speeds, it requires that the CPU reacts with short latencies to the transmit interrupt. A double buffer scheme de-couples the reloading of the transmit buffer from the actual message sending and, therefore, reduces the reactiveness requirements of the CPU. Problems can arise if the sending of a message is finished while the CPU re-loads the second buffer. No buffer would then be ready for transmission, and the CAN bus would be released. At least three transmit buffers are required to meet the first of the above requirements under all circumstances. The MSCAN has three transmit buffers. The second requirement calls for some sort of internal prioritization which the MSCAN implements with the "local priority" concept described in Section 10.4.2.2, "Transmit Structures." 10.4.2.2 Transmit Structures The MSCAN triple transmit buffer scheme optimizes real-time performance by allowing multiple messages to be set up in advance. The three buffers are arranged as shown in Figure 10-39. All three buffers have a 13-byte data structure similar to the outline of the receive buffers (see Section 10.3.3, "Programmer's Model of Message Storage"). An additional Section 10.3.3.4, "Transmit Buffer Priority Register (TBPR) contains an 8-bit local priority field (PRIO) (see Section 10.3.3.4, "Transmit Buffer Priority Register (TBPR)"). The remaining two bytes are used for time stamping of a message, if required (see Section 10.3.3.5, "Time Stamp Register (TSRH-TSRL)"). To transmit a message, the CPU must identify an available transmit buffer, which is indicated by a set transmitter buffer empty (TXEx) flag (see Section 10.3.2.7, "MSCAN Transmitter Flag Register (CANTFLG)"). If a transmit buffer is available, the CPU must set a pointer to this buffer by writing to the CANTBSEL register (see Section 10.3.2.11, "MSCAN Transmit Buffer Selection Register (CANTBSEL)"). This makes the respective buffer accessible within the CANTXFG address space (see Section 10.3.3, "Programmer's Model of Message Storage"). The algorithmic feature associated with the CANTBSEL register simplifies the transmit buffer selection. In addition, this scheme makes the handler software simpler because only one address area is applicable for the transmit process, and the required address space is minimized. The CPU then stores the identifier, the control bits, and the data content into one of the transmit buffers. Finally, the buffer is flagged as ready for transmission by clearing the associated TXE flag. MC9S12XDP512 Data Sheet, Rev. 2.21 458 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) The MSCAN then schedules the message for transmission and signals the successful transmission of the buffer by setting the associated TXE flag. A transmit interrupt (see Section 10.4.7.2, "Transmit Interrupt") is generated1 when TXEx is set and can be used to drive the application software to re-load the buffer. If more than one buffer is scheduled for transmission when the CAN bus becomes available for arbitration, the MSCAN uses the local priority setting of the three buffers to determine the prioritization. For this purpose, every transmit buffer has an 8-bit local priority field (PRIO). The application software programs this field when the message is set up. The local priority reflects the priority of this particular message relative to the set of messages being transmitted from this node. The lowest binary value of the PRIO field is defined to be the highest priority. The internal scheduling process takes place whenever the MSCAN arbitrates for the CAN bus. This is also the case after the occurrence of a transmission error. When a high priority message is scheduled by the application software, it may become necessary to abort a lower priority message in one of the three transmit buffers. Because messages that are already in transmission cannot be aborted, the user must request the abort by setting the corresponding abort request bit (ABTRQ) (see Section 10.3.2.9, "MSCAN Transmitter Message Abort Request Register (CANTARQ)".) The MSCAN then grants the request, if possible, by: 1. Setting the corresponding abort acknowledge flag (ABTAK) in the CANTAAK register. 2. Setting the associated TXE flag to release the buffer. 3. Generating a transmit interrupt. The transmit interrupt handler software can determine from the setting of the ABTAK flag whether the message was aborted (ABTAK = 1) or sent (ABTAK = 0). 10.4.2.3 Receive Structures The received messages are stored in a five stage input FIFO. The five message buffers are alternately mapped into a single memory area (see Figure 10-39). The background receive buffer (RxBG) is exclusively associated with the MSCAN, but the foreground receive buffer (RxFG) is addressable by the CPU (see Figure 10-39). This scheme simplifies the handler software because only one address area is applicable for the receive process. All receive buffers have a size of 15 bytes to store the CAN control bits, the identifier (standard or extended), the data contents, and a time stamp, if enabled (see Section 10.3.3, "Programmer's Model of Message Storage"). The receiver full flag (RXF) (see Section 10.3.2.5, "MSCAN Receiver Flag Register (CANRFLG)") signals the status of the foreground receive buffer. When the buffer contains a correctly received message with a matching identifier, this flag is set. On reception, each message is checked to see whether it passes the filter (see Section 10.4.3, "Identifier Acceptance Filter") and simultaneously is written into the active RxBG. After successful reception of a valid message, the MSCAN shifts the content of RxBG into the receiver FIFO2, sets the RXF flag, and generates a receive interrupt (see Section 10.4.7.3, "Receive Interrupt") to the CPU3. The user's receive handler must read the received message from the RxFG and then reset the RXF flag to acknowledge the interrupt and to release the foreground buffer. A new message, which can follow immediately after the IFS 1. The transmit interrupt occurs only if not masked. A polling scheme can be applied on TXEx also. 2. Only if the RXF flag is not set. 3. The receive interrupt occurs only if not masked. A polling scheme can be applied on RXF also. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 459 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) field of the CAN frame, is received into the next available RxBG. If the MSCAN receives an invalid message in its RxBG (wrong identifier, transmission errors, etc.) the actual contents of the buffer will be over-written by the next message. The buffer will then not be shifted into the FIFO. When the MSCAN module is transmitting, the MSCAN receives its own transmitted messages into the background receive buffer, RxBG, but does not shift it into the receiver FIFO, generate a receive interrupt, or acknowledge its own messages on the CAN bus. The exception to this rule is in loopback mode (see Section 10.3.2.2, "MSCAN Control Register 1 (CANCTL1)") where the MSCAN treats its own messages exactly like all other incoming messages. The MSCAN receives its own transmitted messages in the event that it loses arbitration. If arbitration is lost, the MSCAN must be prepared to become a receiver. An overrun condition occurs when all receive message buffers in the FIFO are filled with correctly received messages with accepted identifiers and another message is correctly received from the CAN bus with an accepted identifier. The latter message is discarded and an error interrupt with overrun indication is generated if enabled (see Section 10.4.7.5, "Error Interrupt"). The MSCAN remains able to transmit messages while the receiver FIFO being filled, but all incoming messages are discarded. As soon as a receive buffer in the FIFO is available again, new valid messages will be accepted. 10.4.3 Identifier Acceptance Filter The MSCAN identifier acceptance registers (see Section 10.3.2.12, "MSCAN Identifier Acceptance Control Register (CANIDAC)") define the acceptable patterns of the standard or extended identifier (ID[10:0] or ID[28:0]). Any of these bits can be marked `don't care' in the MSCAN identifier mask registers (see Section 10.3.2.18, "MSCAN Identifier Mask Registers (CANIDMR0-CANIDMR7)"). A filter hit is indicated to the application software by a set receive buffer full flag (RXF = 1) and three bits in the CANIDAC register (see Section 10.3.2.12, "MSCAN Identifier Acceptance Control Register (CANIDAC)"). These identifier hit flags (IDHIT[2:0]) clearly identify the filter section that caused the acceptance. They simplify the application software's task to identify the cause of the receiver interrupt. If more than one hit occurs (two or more filters match), the lower hit has priority. A very flexible programmable generic identifier acceptance filter has been introduced to reduce the CPU interrupt loading. The filter is programmable to operate in four different modes (see Bosch CAN 2.0A/B protocol specification): * Two identifier acceptance filters, each to be applied to: -- The full 29 bits of the extended identifier and to the following bits of the CAN 2.0B frame: - Remote transmission request (RTR) - Identifier extension (IDE) - Substitute remote request (SRR) -- The 11 bits of the standard identifier plus the RTR and IDE bits of the CAN 2.0A/B messages1. This mode implements two filters for a full length CAN 2.0B compliant extended identifier. Figure 10-40 shows how the first 32-bit filter bank (CANIDAR0-CANIDAR3, CANIDMR0-CANIDMR3) produces a filter 0 hit. Similarly, the second filter bank (CANIDAR4-CANIDAR7, CANIDMR4-CANIDMR7) produces a filter 1 hit. 1.Although this mode can be used for standard identifiers, it is recommended to use the four or eight identifier acceptance filters for standard identifiers MC9S12XDP512 Data Sheet, Rev. 2.21 460 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) * * * Four identifier acceptance filters, each to be applied to -- a) the 14 most significant bits of the extended identifier plus the SRR and IDE bits of CAN 2.0B messages or -- b) the 11 bits of the standard identifier, the RTR and IDE bits of CAN 2.0A/B messages. Figure 10-41 shows how the first 32-bit filter bank (CANIDAR0-CANIDA3, CANIDMR0-3CANIDMR) produces filter 0 and 1 hits. Similarly, the second filter bank (CANIDAR4-CANIDAR7, CANIDMR4-CANIDMR7) produces filter 2 and 3 hits. Eight identifier acceptance filters, each to be applied to the first 8 bits of the identifier. This mode implements eight independent filters for the first 8 bits of a CAN 2.0A/B compliant standard identifier or a CAN 2.0B compliant extended identifier. Figure 10-42 shows how the first 32-bit filter bank (CANIDAR0-CANIDAR3, CANIDMR0-CANIDMR3) produces filter 0 to 3 hits. Similarly, the second filter bank (CANIDAR4-CANIDAR7, CANIDMR4-CANIDMR7) produces filter 4 to 7 hits. Closed filter. No CAN message is copied into the foreground buffer RxFG, and the RXF flag is never set. CAN 2.0B Extended Identifier ID28 IDR0 ID21 ID20 IDR1 CAN 2.0A/B Standard Identifier ID10 IDR0 ID3 ID2 IDR1 ID15 IDE ID14 IDR2 ID7 ID6 IDR3 RTR ID10 IDR2 ID3 ID10 IDR3 ID3 AM7 CANIDMR0 AM0 AM7 CANIDMR1 AM0 AM7 CANIDMR2 AM0 AM7 CANIDMR3 AM0 AC7 CANIDAR0 AC0 AC7 CANIDAR1 AC0 AC7 CANIDAR2 AC0 AC7 CANIDAR3 AC0 ID Accepted (Filter 0 Hit) Figure 10-40. 32-bit Maskable Identifier Acceptance Filter MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 461 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) CAN 2.0B Extended Identifier ID28 IDR0 ID21 ID20 IDR1 CAN 2.0A/B Standard Identifier ID10 IDR0 ID3 ID2 IDR1 AM7 CANIDMR0 AM0 AM7 CANIDMR1 AM0 AC7 CANIDAR0 AC0 AC7 CANIDAR1 AC0 ID15 IDE ID14 IDR2 ID7 ID6 IDR3 RTR ID10 IDR2 ID3 ID10 IDR3 ID3 ID Accepted (Filter 0 Hit) AM7 CANIDMR2 AM0 AM7 CANIDMR3 AM0 AC7 CANIDAR2 AC0 AC7 CANIDAR3 AC0 ID Accepted (Filter 1 Hit) Figure 10-41. 16-bit Maskable Identifier Acceptance Filters MC9S12XDP512 Data Sheet, Rev. 2.21 462 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) CAN 2.0B Extended Identifier ID28 IDR0 ID21 ID20 IDR1 CAN 2.0A/B Standard Identifier ID10 IDR0 ID3 ID2 IDR1 AM7 CIDMR0 AM0 AC7 CIDAR0 AC0 ID15 IDE ID14 IDR2 ID7 ID6 IDR3 RTR ID10 IDR2 ID3 ID10 IDR3 ID3 ID Accepted (Filter 0 Hit) AM7 CIDMR1 AM0 AC7 CIDAR1 AC0 ID Accepted (Filter 1 Hit) AM7 CIDMR2 AM0 AC7 CIDAR2 AC0 ID Accepted (Filter 2 Hit) AM7 CIDMR3 AM0 AC7 CIDAR3 AC0 ID Accepted (Filter 3 Hit) Figure 10-42. 8-bit Maskable Identifier Acceptance Filters MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 463 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.4.3.1 Protocol Violation Protection The MSCAN protects the user from accidentally violating the CAN protocol through programming errors. The protection logic implements the following features: * The receive and transmit error counters cannot be written or otherwise manipulated. * All registers which control the configuration of the MSCAN cannot be modified while the MSCAN is on-line. The MSCAN has to be in Initialization Mode. The corresponding INITRQ/INITAK handshake bits in the CANCTL0/CANCTL1 registers (see Section 10.3.2.1, "MSCAN Control Register 0 (CANCTL0)") serve as a lock to protect the following registers: -- MSCAN control 1 register (CANCTL1) -- MSCAN bus timing registers 0 and 1 (CANBTR0, CANBTR1) -- MSCAN identifier acceptance control register (CANIDAC) -- MSCAN identifier acceptance registers (CANIDAR0-CANIDAR7) -- MSCAN identifier mask registers (CANIDMR0-CANIDMR7) * The TXCAN pin is immediately forced to a recessive state when the MSCAN goes into the power down mode or initialization mode (see Section 10.4.5.6, "MSCAN Power Down Mode," and Section 10.4.5.5, "MSCAN Initialization Mode"). * The MSCAN enable bit (CANE) is writable only once in normal system operation modes, which provides further protection against inadvertently disabling the MSCAN. 10.4.3.2 Clock System Figure 10-43 shows the structure of the MSCAN clock generation circuitry. MSCAN Bus Clock CANCLK CLKSRC Prescaler (1 .. 64) Time quanta clock (Tq) CLKSRC Oscillator Clock Figure 10-43. MSCAN Clocking Scheme The clock source bit (CLKSRC) in the CANCTL1 register (10.3.2.2/10-426) defines whether the internal CANCLK is connected to the output of a crystal oscillator (oscillator clock) or to the bus clock. The clock source has to be chosen such that the tight oscillator tolerance requirements (up to 0.4%) of the CAN protocol are met. Additionally, for high CAN bus rates (1 Mbps), a 45% to 55% duty cycle of the clock is required. MC9S12XDP512 Data Sheet, Rev. 2.21 464 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) If the bus clock is generated from a PLL, it is recommended to select the oscillator clock rather than the bus clock due to jitter considerations, especially at the faster CAN bus rates. For microcontrollers without a clock and reset generator (CRG), CANCLK is driven from the crystal oscillator (oscillator clock). A programmable prescaler generates the time quanta (Tq) clock from CANCLK. A time quantum is the atomic unit of time handled by the MSCAN. Eqn. 10-2 f CANCLK = ----------------------------------------------------Tq ( Prescaler value )A bit time is subdivided into three segments as described in the Bosch CAN specification. (see Figure 10-44): * SYNC_SEG: This segment has a fixed length of one time quantum. Signal edges are expected to happen within this section. * Time Segment 1: This segment includes the PROP_SEG and the PHASE_SEG1 of the CAN standard. It can be programmed by setting the parameter TSEG1 to consist of 4 to 16 time quanta. * Time Segment 2: This segment represents the PHASE_SEG2 of the CAN standard. It can be programmed by setting the TSEG2 parameter to be 2 to 8 time quanta long. Eqn. 10-3 f Tq Bit Rate = --------------------------------------------------------------------------------( number of Time Quanta ) NRZ Signal SYNC_SEG Time Segment 1 (PROP_SEG + PHASE_SEG1) Time Segment 2 (PHASE_SEG2) 1 4 ... 16 2 ... 8 8 ... 25 Time Quanta = 1 Bit Time Transmit Point Sample Point (single or triple sampling) Figure 10-44. Segments within the Bit Time MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 465 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-34. Time Segment Syntax Syntax Description System expects transitions to occur on the CAN bus during this period. SYNC_SEG Transmit Point A node in transmit mode transfers a new value to the CAN bus at this point. Sample Point A node in receive mode samples the CAN bus at this point. If the three samples per bit option is selected, then this point marks the position of the third sample. The synchronization jump width (see the Bosch CAN specification for details) can be programmed in a range of 1 to 4 time quanta by setting the SJW parameter. The SYNC_SEG, TSEG1, TSEG2, and SJW parameters are set by programming the MSCAN bus timing registers (CANBTR0, CANBTR1) (see Section 10.3.2.3, "MSCAN Bus Timing Register 0 (CANBTR0)" and Section 10.3.2.4, "MSCAN Bus Timing Register 1 (CANBTR1)"). Table 10-35 gives an overview of the CAN compliant segment settings and the related parameter values. NOTE It is the user's responsibility to ensure the bit time settings are in compliance with the CAN standard. Table 10-35. CAN Standard Compliant Bit Time Segment Settings Synchronization Jump Width Time Segment 1 TSEG1 Time Segment 2 TSEG2 5 .. 10 4 .. 9 2 1 1 .. 2 0 .. 1 4 .. 11 3 .. 10 3 2 1 .. 3 0 .. 2 5 .. 12 4 .. 11 4 3 1 .. 4 0 .. 3 6 .. 13 5 .. 12 5 4 1 .. 4 0 .. 3 7 .. 14 6 .. 13 6 5 1 .. 4 0 .. 3 8 .. 15 7 .. 14 7 6 1 .. 4 0 .. 3 9 .. 16 8 .. 15 8 7 1 .. 4 0 .. 3 10.4.4 10.4.4.1 SJW Modes of Operation Normal Modes The MSCAN module behaves as described within this specification in all normal system operation modes. 10.4.4.2 Special Modes The MSCAN module behaves as described within this specification in all special system operation modes. MC9S12XDP512 Data Sheet, Rev. 2.21 466 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) 10.4.4.3 Emulation Modes In all emulation modes, the MSCAN module behaves just like normal system operation modes as described within this specification. 10.4.4.4 Listen-Only Mode In an optional CAN bus monitoring mode (listen-only), the CAN node is able to receive valid data frames and valid remote frames, but it sends only "recessive" bits on the CAN bus. In addition, it cannot start a transmision. If the MAC sub-layer is required to send a "dominant" bit (ACK bit, overload flag, or active error flag), the bit is rerouted internally so that the MAC sub-layer monitors this "dominant" bit, although the CAN bus may remain in recessive state externally. 10.4.4.5 Security Modes The MSCAN module has no security features. 10.4.5 Low-Power Options If the MSCAN is disabled (CANE = 0), the MSCAN clocks are stopped for power saving. If the MSCAN is enabled (CANE = 1), the MSCAN has two additional modes with reduced power consumption, compared to normal mode: sleep and power down mode. In sleep mode, power consumption is reduced by stopping all clocks except those to access the registers from the CPU side. In power down mode, all clocks are stopped and no power is consumed. Table 10-36 summarizes the combinations of MSCAN and CPU modes. A particular combination of modes is entered by the given settings on the CSWAI and SLPRQ/SLPAK bits. For all modes, an MSCAN wake-up interrupt can occur only if the MSCAN is in sleep mode (SLPRQ = 1 and SLPAK = 1), wake-up functionality is enabled (WUPE = 1), and the wake-up interrupt is enabled (WUPIE = 1). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 467 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) Table 10-36. CPU vs. MSCAN Operating Modes MSCAN Mode Reduced Power Consumption CPU Mode Normal Sleep RUN CSWAI = X1 SLPRQ = 0 SLPAK = 0 CSWAI = X SLPRQ = 1 SLPAK = 1 WAIT CSWAI = 0 SLPRQ = 0 SLPAK = 0 CSWAI = 0 SLPRQ = 1 SLPAK = 1 STOP 1 Power Down Disabled (CANE=0) CSWAI = X SLPRQ = X SLPAK = X CSWAI = 1 SLPRQ = X SLPAK = X CSWAI = X SLPRQ = X SLPAK = X CSWAI = X SLPRQ = X SLPAK = X CSWAI = X SLPRQ = X SLPAK = X `X' means don't care. 10.4.5.1 Operation in Run Mode As shown in Table 10-36, only MSCAN sleep mode is available as low power option when the CPU is in run mode. 10.4.5.2 Operation in Wait Mode The WAI instruction puts the MCU in a low power consumption stand-by mode. If the CSWAI bit is set, additional power can be saved in power down mode because the CPU clocks are stopped. After leaving this power down mode, the MSCAN restarts its internal controllers and enters normal mode again. While the CPU is in wait mode, the MSCAN can be operated in normal mode and generate interrupts (registers can be accessed via background debug mode). The MSCAN can also operate in any of the low-power modes depending on the values of the SLPRQ/SLPAK and CSWAI bits as seen in Table 10-36. 10.4.5.3 Operation in Stop Mode The STOP instruction puts the MCU in a low power consumption stand-by mode. In stop mode, the MSCAN is set in power down mode regardless of the value of the SLPRQ/SLPAK and CSWAI bits (Table 10-36). 10.4.5.4 MSCAN Sleep Mode The CPU can request the MSCAN to enter this low power mode by asserting the SLPRQ bit in the CANCTL0 register. The time when the MSCAN enters sleep mode depends on a fixed synchronization delay and its current activity: MC9S12XDP512 Data Sheet, Rev. 2.21 468 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) * * * If there are one or more message buffers scheduled for transmission (TXEx = 0), the MSCAN will continue to transmit until all transmit message buffers are empty (TXEx = 1, transmitted successfully or aborted) and then goes into sleep mode. If the MSCAN is receiving, it continues to receive and goes into sleep mode as soon as the CAN bus next becomes idle. If the MSCAN is neither transmitting nor receiving, it immediately goes into sleep mode. Bus Clock Domain CAN Clock Domain SLPRQ SYNC sync. SLPRQ sync. SYNC SLPAK CPU Sleep Request SLPAK Flag SLPAK SLPRQ Flag MSCAN in Sleep Mode Figure 10-45. Sleep Request / Acknowledge Cycle NOTE The application software must avoid setting up a transmission (by clearing one or more TXEx flag(s)) and immediately request sleep mode (by setting SLPRQ). Whether the MSCAN starts transmitting or goes into sleep mode directly depends on the exact sequence of operations. If sleep mode is active, the SLPRQ and SLPAK bits are set (Figure 10-45). The application software must use SLPAK as a handshake indication for the request (SLPRQ) to go into sleep mode. When in sleep mode (SLPRQ = 1 and SLPAK = 1), the MSCAN stops its internal clocks. However, clocks that allow register accesses from the CPU side continue to run. If the MSCAN is in bus-off state, it stops counting the 128 occurrences of 11 consecutive recessive bits due to the stopped clocks. The TXCAN pin remains in a recessive state. If RXF = 1, the message can be read and RXF can be cleared. Shifting a new message into the foreground buffer of the receiver FIFO (RxFG) does not take place while in sleep mode. It is possible to access the transmit buffers and to clear the associated TXE flags. No message abort takes place while in sleep mode. If the WUPE bit in CANCTL0 is not asserted, the MSCAN will mask any activity it detects on CAN. The RXCAN pin is therefore held internally in a recessive state. This locks the MSCAN in sleep mode (Figure 10-46). WUPE must be set before entering sleep mode to take effect. The MSCAN is able to leave sleep mode (wake up) only when: * CAN bus activity occurs and WUPE = 1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 469 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) * or the CPU clears the SLPRQ bit NOTE The CPU cannot clear the SLPRQ bit before sleep mode (SLPRQ = 1 and SLPAK = 1) is active. After wake-up, the MSCAN waits for 11 consecutive recessive bits to synchronize to the CAN bus. As a consequence, if the MSCAN is woken-up by a CAN frame, this frame is not received. The receive message buffers (RxFG and RxBG) contain messages if they were received before sleep mode was entered. All pending actions will be executed upon wake-up; copying of RxBG into RxFG, message aborts and message transmissions. If the MSCAN remains in bus-off state after sleep mode was exited, it continues counting the 128 occurrences of 11 consecutive recessive bits. CAN Activity (CAN Activity & WUPE) | SLPRQ Wait for Idle StartUp CAN Activity SLPRQ CAN Activity & SLPRQ Sleep Idle (CAN Activity & WUPE) | CAN Activity CAN Activity & SLPRQ CAN Activity Tx/Rx Message Active CAN Activity Figure 10-46. Simplified State Transitions for Entering/Leaving Sleep Mode 10.4.5.5 MSCAN Initialization Mode In initialization mode, any on-going transmission or reception is immediately aborted and synchronization to the CAN bus is lost, potentially causing CAN protocol violations. To protect the CAN bus system from fatal consequences of violations, the MSCAN immediately drives the TXCAN pin into a recessive state. MC9S12XDP512 Data Sheet, Rev. 2.21 470 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) NOTE The user is responsible for ensuring that the MSCAN is not active when initialization mode is entered. The recommended procedure is to bring the MSCAN into sleep mode (SLPRQ = 1 and SLPAK = 1) before setting the INITRQ bit in the CANCTL0 register. Otherwise, the abort of an on-going message can cause an error condition and can impact other CAN bus devices. In initialization mode, the MSCAN is stopped. However, interface registers remain accessible. This mode is used to reset the CANCTL0, CANRFLG, CANRIER, CANTFLG, CANTIER, CANTARQ, CANTAAK, and CANTBSEL registers to their default values. In addition, the MSCAN enables the configuration of the CANBTR0, CANBTR1 bit timing registers; CANIDAC; and the CANIDAR, CANIDMR message filters. See Section 10.3.2.1, "MSCAN Control Register 0 (CANCTL0)," for a detailed description of the initialization mode. Bus Clock Domain CAN Clock Domain INITRQ SYNC sync. INITRQ sync. SYNC INITAK CPU Init Request INITAK Flag INITAK INIT Flag Figure 10-47. Initialization Request/Acknowledge Cycle Due to independent clock domains within the MSCAN, INITRQ must be synchronized to all domains by using a special handshake mechanism. This handshake causes additional synchronization delay (see Section Figure 10-47., "Initialization Request/Acknowledge Cycle"). If there is no message transfer ongoing on the CAN bus, the minimum delay will be two additional bus clocks and three additional CAN clocks. When all parts of the MSCAN are in initialization mode, the INITAK flag is set. The application software must use INITAK as a handshake indication for the request (INITRQ) to go into initialization mode. NOTE The CPU cannot clear INITRQ before initialization mode (INITRQ = 1 and INITAK = 1) is active. 10.4.5.6 MSCAN Power Down Mode The MSCAN is in power down mode (Table 10-36) when * CPU is in stop mode MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 471 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) * or CPU is in wait mode and the CSWAI bit is set When entering the power down mode, the MSCAN immediately stops all ongoing transmissions and receptions, potentially causing CAN protocol violations. To protect the CAN bus system from fatal consequences of violations to the above rule, the MSCAN immediately drives the TXCAN pin into a recessive state. NOTE The user is responsible for ensuring that the MSCAN is not active when power down mode is entered. The recommended procedure is to bring the MSCAN into Sleep mode before the STOP or WAI instruction (if CSWAI is set) is executed. Otherwise, the abort of an ongoing message can cause an error condition and impact other CAN bus devices. In power down mode, all clocks are stopped and no registers can be accessed. If the MSCAN was not in sleep mode before power down mode became active, the module performs an internal recovery cycle after powering up. This causes some fixed delay before the module enters normal mode again. 10.4.5.7 Programmable Wake-Up Function The MSCAN can be programmed to wake up the MSCAN as soon as CAN bus activity is detected (see control bit WUPE in Section 10.3.2.1, "MSCAN Control Register 0 (CANCTL0)"). The sensitivity to existing CAN bus action can be modified by applying a low-pass filter function to the RXCAN input line while in sleep mode (see control bit WUPM in Section 10.3.2.2, "MSCAN Control Register 1 (CANCTL1)"). This feature can be used to protect the MSCAN from wake-up due to short glitches on the CAN bus lines. Such glitches can result from--for example--electromagnetic interference within noisy environments. 10.4.6 Reset Initialization The reset state of each individual bit is listed in Section 10.3.2, "Register Descriptions," which details all the registers and their bit-fields. 10.4.7 Interrupts This section describes all interrupts originated by the MSCAN. It documents the enable bits and generated flags. Each interrupt is listed and described separately. 10.4.7.1 Description of Interrupt Operation The MSCAN supports four interrupt vectors (see Table 10-37), any of which can be individually masked (for details see sections from Section 10.3.2.6, "MSCAN Receiver Interrupt Enable Register (CANRIER)," to Section 10.3.2.8, "MSCAN Transmitter Interrupt Enable Register (CANTIER)"). MC9S12XDP512 Data Sheet, Rev. 2.21 472 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) NOTE The dedicated interrupt vector addresses are defined in the Resets and Interrupts chapter. Table 10-37. Interrupt Vectors Interrupt Source 10.4.7.2 CCR Mask Local Enable Wake-Up Interrupt (WUPIF) I bit CANRIER (WUPIE) Error Interrupts Interrupt (CSCIF, OVRIF) I bit CANRIER (CSCIE, OVRIE) Receive Interrupt (RXF) I bit CANRIER (RXFIE) Transmit Interrupts (TXE[2:0]) I bit CANTIER (TXEIE[2:0]) Transmit Interrupt At least one of the three transmit buffers is empty (not scheduled) and can be loaded to schedule a message for transmission. The TXEx flag of the empty message buffer is set. 10.4.7.3 Receive Interrupt A message is successfully received and shifted into the foreground buffer (RxFG) of the receiver FIFO. This interrupt is generated immediately after receiving the EOF symbol. The RXF flag is set. If there are multiple messages in the receiver FIFO, the RXF flag is set as soon as the next message is shifted to the foreground buffer. 10.4.7.4 Wake-Up Interrupt A wake-up interrupt is generated if activity on the CAN bus occurs during MSCAN internal sleep mode. WUPE (see Section 10.3.2.1, "MSCAN Control Register 0 (CANCTL0)") must be enabled. 10.4.7.5 Error Interrupt An error interrupt is generated if an overrun of the receiver FIFO, error, warning, or bus-off condition occurrs. Section 10.3.2.5, "MSCAN Receiver Flag Register (CANRFLG) indicates one of the following conditions: * Overrun -- An overrun condition of the receiver FIFO as described in Section 10.4.2.3, "Receive Structures," occurred. * CAN Status Change -- The actual value of the transmit and receive error counters control the CAN bus state of the MSCAN. As soon as the error counters skip into a critical range (Tx/Rx-warning, Tx/Rx-error, bus-off) the MSCAN flags an error condition. The status change, which caused the error condition, is indicated by the TSTAT and RSTAT flags (see Section 10.3.2.5, "MSCAN Receiver Flag Register (CANRFLG)" and Section 10.3.2.6, "MSCAN Receiver Interrupt Enable Register (CANRIER)"). 10.4.7.6 Interrupt Acknowledge Interrupts are directly associated with one or more status flags in either the Section 10.3.2.5, "MSCAN Receiver Flag Register (CANRFLG)" or the Section 10.3.2.7, "MSCAN Transmitter Flag Register MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 473 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) (CANTFLG)." Interrupts are pending as long as one of the corresponding flags is set. The flags in CANRFLG and CANTFLG must be reset within the interrupt handler to handshake the interrupt. The flags are reset by writing a 1 to the corresponding bit position. A flag cannot be cleared if the respective condition prevails. NOTE It must be guaranteed that the CPU clears only the bit causing the current interrupt. For this reason, bit manipulation instructions (BSET) must not be used to clear interrupt flags. These instructions may cause accidental clearing of interrupt flags which are set after entering the current interrupt service routine. 10.4.7.7 Recovery from Stop or Wait The MSCAN can recover from stop or wait via the wake-up interrupt. This interrupt can only occur if the MSCAN was in sleep mode (SLPRQ = 1 and SLPAK = 1) before entering power down mode, the wake-up option is enabled (WUPE = 1), and the wake-up interrupt is enabled (WUPIE = 1). 10.5 10.5.1 Initialization/Application Information MSCAN initialization The procedure to initially start up the MSCAN module out of reset is as follows: 1. Assert CANE 2. Write to the configuration registers in initialization mode 3. Clear INITRQ to leave initialization mode and enter normal mode If the configuration of registers which are writable in initialization mode needs to be changed only when the MSCAN module is in normal mode: 1. Bring the module into sleep mode by setting SLPRQ and awaiting SLPAK to assert after the CAN bus becomes idle. 2. Enter initialization mode: assert INITRQ and await INITAK 3. Write to the configuration registers in initialization mode 4. Clear INITRQ to leave initialization mode and continue in normal mode 10.5.2 Bus-Off Recovery The bus-off recovery is user configurable. The bus-off state can either be left automatically or on user request. For reasons of backwards compatibility, the MSCAN defaults to automatic recovery after reset. In this case, the MSCAN will become error active again after counting 128 occurrences of 11 consecutive recessive bits on the CAN bus (See the Bosch CAN specification for details). MC9S12XDP512 Data Sheet, Rev. 2.21 474 Freescale Semiconductor Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) If the MSCAN is configured for user request (BORM set in Section 10.3.2.2, "MSCAN Control Register 1 (CANCTL1)"), the recovery from bus-off starts after both independent events have become true: * 128 occurrences of 11 consecutive recessive bits on the CAN bus have been monitored * BOHOLD in Section 10.3.2.14, "MSCAN Miscellaneous Register (CANMISC) has been cleared by the user These two events may occur in any order. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 475 Chapter 10 Freescale's Scalable Controller Area Network (S12MSCANV3) MC9S12XDP512 Data Sheet, Rev. 2.21 476 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.1 Introduction This block guide provides an overview of the serial communication interface (SCI) module. The SCI allows asynchronous serial communications with peripheral devices and other CPUs. 11.1.1 Glossary IR: InfraRed IrDA: Infrared Design Associate IRQ: Interrupt Request LIN: Local Interconnect Network LSB: Least Significant Bit MSB: Most Significant Bit NRZ: Non-Return-to-Zero RZI: Return-to-Zero-Inverted RXD: Receive Pin SCI : Serial Communication Interface TXD: Transmit Pin 11.1.2 Features The SCI includes these distinctive features: * Full-duplex or single-wire operation * Standard mark/space non-return-to-zero (NRZ) format * Selectable IrDA 1.4 return-to-zero-inverted (RZI) format with programmable pulse widths * 13-bit baud rate selection * Programmable 8-bit or 9-bit data format * Separately enabled transmitter and receiver * Programmable polarity for transmitter and receiver MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 477 Chapter 11 Serial Communication Interface (S12SCIV5) * * * * * * Programmable transmitter output parity Two receiver wakeup methods: -- Idle line wakeup -- Address mark wakeup Interrupt-driven operation with eight flags: -- Transmitter empty -- Transmission complete -- Receiver full -- Idle receiver input -- Receiver overrun -- Noise error -- Framing error -- Parity error -- Receive wakeup on active edge -- Transmit collision detect supporting LIN -- Break Detect supporting LIN Receiver framing error detection Hardware parity checking 1/16 bit-time noise detection 11.1.3 Modes of Operation The SCI functions the same in normal, special, and emulation modes. It has two low power modes, wait and stop modes. * Run mode * Wait mode * Stop mode 11.1.4 Block Diagram Figure 11-1 is a high level block diagram of the SCI module, showing the interaction of various function blocks. MC9S12XDP512 Data Sheet, Rev. 2.21 478 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) SCI Data Register RXD Data In Infrared Decoder Receive Shift Register IDLE Receive & Wakeup Control Bus Clock Baud Rate Generator Receive RDRF/OR Interrupt Generation BRKD RXEDG BERR Data Format Control 1/16 Transmit Control Transmit Shift Register SCI Interrupt Request Transmit TDRE Interrupt Generation TC Infrared Encoder Data Out TXD SCI Data Register Figure 11-1. SCI Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 479 Chapter 11 Serial Communication Interface (S12SCIV5) 11.2 External Signal Description The SCI module has a total of two external pins. 11.2.1 TXD -- Transmit Pin The TXD pin transmits SCI (standard or infrared) data. It will idle high in either mode and is high impedance anytime the transmitter is disabled. 11.2.2 RXD -- Receive Pin The RXD pin receives SCI (standard or infrared) data. An idle line is detected as a line high. This input is ignored when the receiver is disabled and should be terminated to a known voltage. 11.3 Memory Map and Register Definition This section provides a detailed description of all the SCI registers. 11.3.1 Module Memory Map and Register Definition The memory map for the SCI module is given below in Figure 11-2. The address listed for each register is the address offset. The total address for each register is the sum of the base address for the SCI module and the address offset for each register. MC9S12XDP512 Data Sheet, Rev. 2.21 480 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2 Register Descriptions This section consists of register descriptions in address order. Each description includes a standard register diagram with an associated figure number. Writes to a reserved register locations do not have any effect and reads of these locations return a zero. Details of register bit and field function follow the register diagrams, in bit order. Register Name SCIBDH1 R W SCIBDL1 R W SCICR11 R W SCIASR12 R W SCIACR12 R W SCIACR22 Bit 7 6 5 4 3 2 1 Bit 0 IREN TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 LOOPS SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 BERRV BERRIF BKDIF 0 0 0 0 BERRIE BKDIE 0 0 0 0 0 BERRM1 BERRM0 BKDFE TIE TCIE RIE ILIE TE RE RWU SBK TDRE TC RDRF IDLE OR NF FE PF 0 0 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 0 RXEDGIF RXEDGIE R W SCICR2 R W SCISR1 R 0 W SCISR2 R W SCIDRH R AMAP R8 W SCIDRL T8 RAF R R7 R6 R5 R4 R3 R2 R1 R0 W T7 T6 T5 T4 T3 T2 T1 T0 1.These registers are accessible if the AMAP bit in the SCISR2 register is set to zero. 2,These registers are accessible if the AMAP bit in the SCISR2 register is set to one. = Unimplemented or Reserved Figure 11-2. SCI Register Summary 1 2 Those registers are accessible if the AMAP bit in the SCISR2 register is set to zero Those registers are accessible if the AMAP bit in the SCISR2 register is set to one MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 481 Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.1 R W Reset SCI Baud Rate Registers (SCIBDH, SCIBDL) 7 6 5 4 3 2 1 0 IREN TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 0 0 0 0 0 0 0 0 Figure 11-3. SCI Baud Rate Register (SCIBDH) R W Reset 7 6 5 4 3 2 1 0 SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 0 0 0 0 0 0 0 0 Figure 11-4. SCI Baud Rate Register (SCIBDL) Read: Anytime, if AMAP = 0. If only SCIBDH is written to, a read will not return the correct data until SCIBDL is written to as well, following a write to SCIBDH. Write: Anytime, if AMAP = 0. NOTE Those two registers are only visible in the memory map if AMAP = 0 (reset condition). The SCI baud rate register is used by to determine the baud rate of the SCI, and to control the infrared modulation/demodulation submodule. Table 11-1. SCIBDH and SCIBDL Field Descriptions Field 7 IREN Description Infrared Enable Bit -- This bit enables/disables the infrared modulation/demodulation submodule. 0 IR disabled 1 IR enabled 6:5 TNP[1:0] Transmitter Narrow Pulse Bits -- These bits enable whether the SCI transmits a 1/16, 3/16, 1/32 or 1/4 narrow pulse. See Table 11-2. 4:0 7:0 SBR[12:0] SCI Baud Rate Bits -- The baud rate for the SCI is determined by the bits in this register. The baud rate is calculated two different ways depending on the state of the IREN bit. The formulas for calculating the baud rate are: When IREN = 0 then, SCI baud rate = SCI bus clock / (16 x SBR[12:0]) When IREN = 1 then, SCI baud rate = SCI bus clock / (32 x SBR[12:1]) Note: The baud rate generator is disabled after reset and not started until the TE bit or the RE bit is set for the first time. The baud rate generator is disabled when (SBR[12:0] = 0 and IREN = 0) or (SBR[12:1] = 0 and IREN = 1). Note: Writing to SCIBDH has no effect without writing to SCIBDL, because writing to SCIBDH puts the data in a temporary location until SCIBDL is written to. MC9S12XDP512 Data Sheet, Rev. 2.21 482 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) Table 11-2. IRSCI Transmit Pulse Width 11.3.2.2 R W Reset TNP[1:0] Narrow Pulse Width 11 1/4 10 1/32 01 1/16 00 3/16 SCI Control Register 1 (SCICR1) 7 6 5 4 3 2 1 0 LOOPS SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 0 0 0 0 Figure 11-5. SCI Control Register 1 (SCICR1) Read: Anytime, if AMAP = 0. Write: Anytime, if AMAP = 0. NOTE This register is only visible in the memory map if AMAP = 0 (reset condition). Table 11-3. SCICR1 Field Descriptions Field Description 7 LOOPS Loop Select Bit -- LOOPS enables loop operation. In loop operation, the RXD pin is disconnected from the SCI and the transmitter output is internally connected to the receiver input. Both the transmitter and the receiver must be enabled to use the loop function. 0 Normal operation enabled 1 Loop operation enabled The receiver input is determined by the RSRC bit. 6 SCISWAI 5 RSRC 4 M 3 WAKE SCI Stop in Wait Mode Bit -- SCISWAI disables the SCI in wait mode. 0 SCI enabled in wait mode 1 SCI disabled in wait mode Receiver Source Bit -- When LOOPS = 1, the RSRC bit determines the source for the receiver shift register input. See Table 11-4. 0 Receiver input internally connected to transmitter output 1 Receiver input connected externally to transmitter Data Format Mode Bit -- MODE determines whether data characters are eight or nine bits long. 0 One start bit, eight data bits, one stop bit 1 One start bit, nine data bits, one stop bit Wakeup Condition Bit -- WAKE determines which condition wakes up the SCI: a logic 1 (address mark) in the most significant bit position of a received data character or an idle condition on the RXD pin. 0 Idle line wakeup 1 Address mark wakeup MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 483 Chapter 11 Serial Communication Interface (S12SCIV5) Table 11-3. SCICR1 Field Descriptions (continued) Field Description 2 ILT Idle Line Type Bit -- ILT determines when the receiver starts counting logic 1s as idle character bits. The counting begins either after the start bit or after the stop bit. If the count begins after the start bit, then a string of logic 1s preceding the stop bit may cause false recognition of an idle character. Beginning the count after the stop bit avoids false idle character recognition, but requires properly synchronized transmissions. 0 Idle character bit count begins after start bit 1 Idle character bit count begins after stop bit 1 PE Parity Enable Bit -- PE enables the parity function. When enabled, the parity function inserts a parity bit in the most significant bit position. 0 Parity function disabled 1 Parity function enabled 0 PT Parity Type Bit -- PT determines whether the SCI generates and checks for even parity or odd parity. With even parity, an even number of 1s clears the parity bit and an odd number of 1s sets the parity bit. With odd parity, an odd number of 1s clears the parity bit and an even number of 1s sets the parity bit. 1 Even parity 1 Odd parity Table 11-4. Loop Functions LOOPS RSRC Function 0 x Normal operation 1 0 Loop mode with transmitter output internally connected to receiver input 1 1 Single-wire mode with TXD pin connected to receiver input MC9S12XDP512 Data Sheet, Rev. 2.21 484 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.3 SCI Alternative Status Register 1 (SCIASR1) 7 R W Reset RXEDGIF 0 6 5 4 3 2 0 0 0 0 BERRV 0 0 0 0 0 1 0 BERRIF BKDIF 0 0 = Unimplemented or Reserved Figure 11-6. SCI Alternative Status Register 1 (SCIASR1) Read: Anytime, if AMAP = 1 Write: Anytime, if AMAP = 1 Table 11-5. SCIASR1 Field Descriptions Field 7 RXEDGIF Description Receive Input Active Edge Interrupt Flag -- RXEDGIF is asserted, if an active edge (falling if RXPOL = 0, rising if RXPOL = 1) on the RXD input occurs. RXEDGIF bit is cleared by writing a "1" to it. 0 No active receive on the receive input has occurred 1 An active edge on the receive input has occurred 2 BERRV Bit Error Value -- BERRV reflects the state of the RXD input when the bit error detect circuitry is enabled and a mismatch to the expected value happened. The value is only meaningful, if BERRIF = 1. 0 A low input was sampled, when a high was expected 1 A high input reassembled, when a low was expected 1 BERRIF Bit Error Interrupt Flag -- BERRIF is asserted, when the bit error detect circuitry is enabled and if the value sampled at the RXD input does not match the transmitted value. If the BERRIE interrupt enable bit is set an interrupt will be generated. The BERRIF bit is cleared by writing a "1" to it. 0 No mismatch detected 1 A mismatch has occurred 0 BKDIF Break Detect Interrupt Flag -- BKDIF is asserted, if the break detect circuitry is enabled and a break signal is received. If the BKDIE interrupt enable bit is set an interrupt will be generated. The BKDIF bit is cleared by writing a "1" to it. 0 No break signal was received 1 A break signal was received MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 485 Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.4 SCI Alternative Control Register 1 (SCIACR1) 7 R W Reset RXEDGIE 0 6 5 4 3 2 0 0 0 0 0 0 0 0 0 0 1 0 BERRIE BKDIE 0 0 = Unimplemented or Reserved Figure 11-7. SCI Alternative Control Register 1 (SCIACR1) Read: Anytime, if AMAP = 1 Write: Anytime, if AMAP = 1 Table 11-6. SCIACR1 Field Descriptions Field Description 7 RSEDGIE Receive Input Active Edge Interrupt Enable -- RXEDGIE enables the receive input active edge interrupt flag, RXEDGIF, to generate interrupt requests. 0 RXEDGIF interrupt requests disabled 1 RXEDGIF interrupt requests enabled 1 BERRIE 0 BKDIE Bit Error Interrupt Enable -- BERRIE enables the bit error interrupt flag, BERRIF, to generate interrupt requests. 0 BERRIF interrupt requests disabled 1 BERRIF interrupt requests enabled Break Detect Interrupt Enable -- BKDIE enables the break detect interrupt flag, BKDIF, to generate interrupt requests. 0 BKDIF interrupt requests disabled 1 BKDIF interrupt requests enabled MC9S12XDP512 Data Sheet, Rev. 2.21 486 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.5 R SCI Alternative Control Register 2 (SCIACR2) 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 W Reset 2 1 0 BERRM1 BERRM0 BKDFE 0 0 0 = Unimplemented or Reserved Figure 11-8. SCI Alternative Control Register 2 (SCIACR2) Read: Anytime, if AMAP = 1 Write: Anytime, if AMAP = 1 Table 11-7. SCIACR2 Field Descriptions Field Description 2:1 Bit Error Mode -- Those two bits determines the functionality of the bit error detect feature. See Table 11-8. BERRM[1:0] 0 BKDFE Break Detect Feature Enable -- BKDFE enables the break detect circuitry. 0 Break detect circuit disabled 1 Break detect circuit enabled Table 11-8. Bit Error Mode Coding BERRM1 BERRM0 Function 0 0 Bit error detect circuit is disabled 0 1 Receive input sampling occurs during the 9th time tick of a transmitted bit (refer to Figure 11-19) 1 0 Receive input sampling occurs during the 13th time tick of a transmitted bit (refer to Figure 11-19) 1 1 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 487 Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.6 R W Reset SCI Control Register 2 (SCICR2) 7 6 5 4 3 2 1 0 TIE TCIE RIE ILIE TE RE RWU SBK 0 0 0 0 0 0 0 0 Figure 11-9. SCI Control Register 2 (SCICR2) Read: Anytime Write: Anytime Table 11-9. SCICR2 Field Descriptions Field 7 TIE Description Transmitter Interrupt Enable Bit -- TIE enables the transmit data register empty flag, TDRE, to generate interrupt requests. 0 TDRE interrupt requests disabled 1 TDRE interrupt requests enabled 6 TCIE Transmission Complete Interrupt Enable Bit -- TCIE enables the transmission complete flag, TC, to generate interrupt requests. 0 TC interrupt requests disabled 1 TC interrupt requests enabled 5 RIE Receiver Full Interrupt Enable Bit -- RIE enables the receive data register full flag, RDRF, or the overrun flag, OR, to generate interrupt requests. 0 RDRF and OR interrupt requests disabled 1 RDRF and OR interrupt requests enabled 4 ILIE Idle Line Interrupt Enable Bit -- ILIE enables the idle line flag, IDLE, to generate interrupt requests. 0 IDLE interrupt requests disabled 1 IDLE interrupt requests enabled 3 TE Transmitter Enable Bit -- TE enables the SCI transmitter and configures the TXD pin as being controlled by the SCI. The TE bit can be used to queue an idle preamble. 0 Transmitter disabled 1 Transmitter enabled 2 RE Receiver Enable Bit -- RE enables the SCI receiver. 0 Receiver disabled 1 Receiver enabled 1 RWU Receiver Wakeup Bit -- Standby state 0 Normal operation. 1 RWU enables the wakeup function and inhibits further receiver interrupt requests. Normally, hardware wakes the receiver by automatically clearing RWU. 0 SBK Send Break Bit -- Toggling SBK sends one break character (10 or 11 logic 0s, respectively 13 or 14 logics 0s if BRK13 is set). Toggling implies clearing the SBK bit before the break character has finished transmitting. As long as SBK is set, the transmitter continues to send complete break characters (10 or 11 bits, respectively 13 or 14 bits). 0 No break characters 1 Transmit break characters MC9S12XDP512 Data Sheet, Rev. 2.21 488 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.7 SCI Status Register 1 (SCISR1) The SCISR1 and SCISR2 registers provides inputs to the MCU for generation of SCI interrupts. Also, these registers can be polled by the MCU to check the status of these bits. The flag-clearing procedures require that the status register be read followed by a read or write to the SCI data register.It is permissible to execute other instructions between the two steps as long as it does not compromise the handling of I/O, but the order of operations is important for flag clearing. R 7 6 5 4 3 2 1 0 TDRE TC RDRF IDLE OR NF FE PF 1 1 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 11-10. SCI Status Register 1 (SCISR1) Read: Anytime Write: Has no meaning or effect Table 11-10. SCISR1 Field Descriptions Field Description 7 TDRE Transmit Data Register Empty Flag -- TDRE is set when the transmit shift register receives a byte from the SCI data register. When TDRE is 1, the transmit data register (SCIDRH/L) is empty and can receive a new value to transmit.Clear TDRE by reading SCI status register 1 (SCISR1), with TDRE set and then writing to SCI data register low (SCIDRL). 0 No byte transferred to transmit shift register 1 Byte transferred to transmit shift register; transmit data register empty 6 TC Transmit Complete Flag -- TC is set low when there is a transmission in progress or when a preamble or break character is loaded. TC is set high when the TDRE flag is set and no data, preamble, or break character is being transmitted.When TC is set, the TXD pin becomes idle (logic 1). Clear TC by reading SCI status register 1 (SCISR1) with TC set and then writing to SCI data register low (SCIDRL). TC is cleared automatically when data, preamble, or break is queued and ready to be sent. TC is cleared in the event of a simultaneous set and clear of the TC flag (transmission not complete). 0 Transmission in progress 1 No transmission in progress 5 RDRF Receive Data Register Full Flag -- RDRF is set when the data in the receive shift register transfers to the SCI data register. Clear RDRF by reading SCI status register 1 (SCISR1) with RDRF set and then reading SCI data register low (SCIDRL). 0 Data not available in SCI data register 1 Received data available in SCI data register 4 IDLE Idle Line Flag -- IDLE is set when 10 consecutive logic 1s (if M = 0) or 11 consecutive logic 1s (if M =1) appear on the receiver input. Once the IDLE flag is cleared, a valid frame must again set the RDRF flag before an idle condition can set the IDLE flag.Clear IDLE by reading SCI status register 1 (SCISR1) with IDLE set and then reading SCI data register low (SCIDRL). 0 Receiver input is either active now or has never become active since the IDLE flag was last cleared 1 Receiver input has become idle Note: When the receiver wakeup bit (RWU) is set, an idle line condition does not set the IDLE flag. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 489 Chapter 11 Serial Communication Interface (S12SCIV5) Table 11-10. SCISR1 Field Descriptions (continued) Field Description 3 OR Overrun Flag -- OR is set when software fails to read the SCI data register before the receive shift register receives the next frame. The OR bit is set immediately after the stop bit has been completely received for the second frame. The data in the shift register is lost, but the data already in the SCI data registers is not affected. Clear OR by reading SCI status register 1 (SCISR1) with OR set and then reading SCI data register low (SCIDRL). 0 No overrun 1 Overrun Note: OR flag may read back as set when RDRF flag is clear. This may happen if the following sequence of events occurs: 1. After the first frame is received, read status register SCISR1 (returns RDRF set and OR flag clear); 2. Receive second frame without reading the first frame in the data register (the second frame is not received and OR flag is set); 3. Read data register SCIDRL (returns first frame and clears RDRF flag in the status register); 4. Read status register SCISR1 (returns RDRF clear and OR set). Event 3 may be at exactly the same time as event 2 or any time after. When this happens, a dummy SCIDRL read following event 4 will be required to clear the OR flag if further frames are to be received. 2 NF Noise Flag -- NF is set when the SCI detects noise on the receiver input. NF bit is set during the same cycle as the RDRF flag but does not get set in the case of an overrun. Clear NF by reading SCI status register 1(SCISR1), and then reading SCI data register low (SCIDRL). 0 No noise 1 Noise 1 FE Framing Error Flag -- FE is set when a logic 0 is accepted as the stop bit. FE bit is set during the same cycle as the RDRF flag but does not get set in the case of an overrun. FE inhibits further data reception until it is cleared. Clear FE by reading SCI status register 1 (SCISR1) with FE set and then reading the SCI data register low (SCIDRL). 0 No framing error 1 Framing error 0 PF Parity Error Flag -- PF is set when the parity enable bit (PE) is set and the parity of the received data does not match the parity type bit (PT). PF bit is set during the same cycle as the RDRF flag but does not get set in the case of an overrun. Clear PF by reading SCI status register 1 (SCISR1), and then reading SCI data register low (SCIDRL). 0 No parity error 1 Parity error MC9S12XDP512 Data Sheet, Rev. 2.21 490 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.8 SCI Status Register 2 (SCISR2) 7 R W Reset AMAP 0 6 5 0 0 0 0 4 3 2 1 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 RAF 0 = Unimplemented or Reserved Figure 11-11. SCI Status Register 2 (SCISR2) Read: Anytime Write: Anytime Table 11-11. SCISR2 Field Descriptions Field Description 7 AMAP Alternative Map -- This bit controls which registers sharing the same address space are accessible. In the reset condition the SCI behaves as previous versions. Setting AMAP=1 allows the access to another set of control and status registers and hides the baud rate and SCI control Register 1. 0 The registers labelled SCIBDH (0x0000),SCIBDL (0x0001), SCICR1 (0x0002) are accessible 1 The registers labelled SCIASR1 (0x0000),SCIACR1 (0x0001), SCIACR2 (0x00002) are accessible 4 TXPOL Transmit Polarity -- This bit control the polarity of the transmitted data. In NRZ format, a one is represented by a mark and a zero is represented by a space for normal polarity, and the opposite for inverted polarity. In IrDA format, a zero is represented by short high pulse in the middle of a bit time remaining idle low for a one for normal polarity, and a zero is represented by short low pulse in the middle of a bit time remaining idle high for a one for inverted polarity. 0 Normal polarity 1 Inverted polarity 3 RXPOL Receive Polarity -- This bit control the polarity of the received data. In NRZ format, a one is represented by a mark and a zero is represented by a space for normal polarity, and the opposite for inverted polarity. In IrDA format, a zero is represented by short high pulse in the middle of a bit time remaining idle low for a one for normal polarity, and a zero is represented by short low pulse in the middle of a bit time remaining idle high for a one for inverted polarity. 0 Normal polarity 1 Inverted polarity 2 BRK13 Break Transmit Character Length -- This bit determines whether the transmit break character is 10 or 11 bit respectively 13 or 14 bits long. The detection of a framing error is not affected by this bit. 0 Break character is 10 or 11 bit long 1 Break character is 13 or 14 bit long 1 TXDIR Transmitter Pin Data Direction in Single-Wire Mode -- This bit determines whether the TXD pin is going to be used as an input or output, in the single-wire mode of operation. This bit is only relevant in the single-wire mode of operation. 0 TXD pin to be used as an input in single-wire mode 1 TXD pin to be used as an output in single-wire mode 0 RAF Receiver Active Flag -- RAF is set when the receiver detects a logic 0 during the RT1 time period of the start bit search. RAF is cleared when the receiver detects an idle character. 0 No reception in progress 1 Reception in progress MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 491 Chapter 11 Serial Communication Interface (S12SCIV5) 11.3.2.9 SCI Data Registers (SCIDRH, SCIDRL) 7 R 6 R8 W Reset 0 T8 0 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 11-12. SCI Data Registers (SCIDRH) 7 6 5 4 3 2 1 0 R R7 R6 R5 R4 R3 R2 R1 R0 W T7 T6 T5 T4 T3 T2 T1 T0 0 0 0 0 0 0 0 0 Reset Figure 11-13. SCI Data Registers (SCIDRL) Read: Anytime; reading accesses SCI receive data register Write: Anytime; writing accesses SCI transmit data register; writing to R8 has no effect Table 11-12. SCIDRH and SCIDRL Field Descriptions Field Description SCIDRH 7 R8 Received Bit 8 -- R8 is the ninth data bit received when the SCI is configured for 9-bit data format (M = 1). SCIDRH 6 T8 Transmit Bit 8 -- T8 is the ninth data bit transmitted when the SCI is configured for 9-bit data format (M = 1). SCIDRL 7:0 R[7:0] T[7:0] R7:R0 -- Received bits seven through zero for 9-bit or 8-bit data formats T7:T0 -- Transmit bits seven through zero for 9-bit or 8-bit formats NOTE If the value of T8 is the same as in the previous transmission, T8 does not have to be rewritten.The same value is transmitted until T8 is rewritten In 8-bit data format, only SCI data register low (SCIDRL) needs to be accessed. When transmitting in 9-bit data format and using 8-bit write instructions, write first to SCI data register high (SCIDRH), then SCIDRL. MC9S12XDP512 Data Sheet, Rev. 2.21 492 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.4 Functional Description This section provides a complete functional description of the SCI block, detailing the operation of the design from the end user perspective in a number of subsections. Figure 11-14 shows the structure of the SCI module. The SCI allows full duplex, asynchronous, serial communication between the CPU and remote devices, including other CPUs. The SCI transmitter and receiver operate independently, although they use the same baud rate generator. The CPU monitors the status of the SCI, writes the data to be transmitted, and processes received data. R8 IREN SCI Data Register NF FE Ir_RXD Bus Clock Receive Shift Register SCRXD Receive and Wakeup Control PF RAF RE IDLE RWU RDRF LOOPS OR RSRC M Baud Rate Generator IDLE ILIE RDRF/OR Infrared Receive Decoder R16XCLK RXD RIE TIE WAKE Data Format Control ILT PE SBR12:SBR0 TDRE TDRE TC SCI Interrupt Request PT TC TCIE TE /16 Transmit Control LOOPS SBK RSRC T8 Transmit Shift Register RXEDGIE Active Edge Detect RXEDGIF BKDIF RXD SCI Data Register Break Detect BKDFE SCTXD BKDIE LIN Transmit BERRIF Collision Detect BERRIE R16XCLK Infrared Transmit Encoder BERRM[1:0] Ir_TXD TXD R32XCLK TNP[1:0] IREN Figure 11-14. Detailed SCI Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 493 Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.1 Infrared Interface Submodule This module provides the capability of transmitting narrow pulses to an IR LED and receiving narrow pulses and transforming them to serial bits, which are sent to the SCI. The IrDA physical layer specification defines a half-duplex infrared communication link for exchange data. The full standard includes data rates up to 16 Mbits/s. This design covers only data rates between 2.4 Kbits/s and 115.2 Kbits/s. The infrared submodule consists of two major blocks: the transmit encoder and the receive decoder. The SCI transmits serial bits of data which are encoded by the infrared submodule to transmit a narrow pulse for every zero bit. No pulse is transmitted for every one bit. When receiving data, the IR pulses should be detected using an IR photo diode and transformed to CMOS levels by the IR receive decoder (external from the MCU). The narrow pulses are then stretched by the infrared submodule to get back to a serial bit stream to be received by the SCI.The polarity of transmitted pulses and expected receive pulses can be inverted so that a direct connection can be made to external IrDA transceiver modules that uses active low pulses. The infrared submodule receives its clock sources from the SCI. One of these two clocks are selected in the infrared submodule in order to generate either 3/16, 1/16, 1/32 or 1/4 narrow pulses during transmission. The infrared block receives two clock sources from the SCI, R16XCLK and R32XCLK, which are configured to generate the narrow pulse width during transmission. The R16XCLK and R32XCLK are internal clocks with frequencies 16 and 32 times the baud rate respectively. Both R16XCLK and R32XCLK clocks are used for transmitting data. The receive decoder uses only the R16XCLK clock. 11.4.1.1 Infrared Transmit Encoder The infrared transmit encoder converts serial bits of data from transmit shift register to the TXD pin. A narrow pulse is transmitted for a zero bit and no pulse for a one bit. The narrow pulse is sent in the middle of the bit with a duration of 1/32, 1/16, 3/16 or 1/4 of a bit time. A narrow high pulse is transmitted for a zero bit when TXPOL is cleared, while a narrow low pulse is transmitted for a zero bit when TXPOL is set. 11.4.1.2 Infrared Receive Decoder The infrared receive block converts data from the RXD pin to the receive shift register. A narrow pulse is expected for each zero received and no pulse is expected for each one received. A narrow high pulse is expected for a zero bit when RXPOL is cleared, while a narrow low pulse is expected for a zero bit when RXPOL is set. This receive decoder meets the edge jitter requirement as defined by the IrDA serial infrared physical layer specification. 11.4.2 LIN Support This module provides some basic support for the LIN protocol. At first this is a break detect circuitry making it easier for the LIN software to distinguish a break character from an incoming data stream. As a further addition is supports a collision detection at the bit level as well as cancelling pending transmissions. MC9S12XDP512 Data Sheet, Rev. 2.21 494 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.3 Data Format The SCI uses the standard NRZ mark/space data format. When Infrared is enabled, the SCI uses RZI data format where zeroes are represented by light pulses and ones remain low. See Figure 11-15 below. 8-Bit Data Format (Bit M in SCICR1 Clear) Start Bit Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Possible Parity Bit Bit 6 STOP Bit Bit 7 Next Start Bit Standard SCI Data Infrared SCI Data 9-Bit Data Format (Bit M in SCICR1 Set) Start Bit Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 POSSIBLE PARITY Bit Bit 6 Bit 7 Bit 8 STOP Bit NEXT START Bit Standard SCI Data Infrared SCI Data Figure 11-15. SCI Data Formats Each data character is contained in a frame that includes a start bit, eight or nine data bits, and a stop bit. Clearing the M bit in SCI control register 1 configures the SCI for 8-bit data characters. A frame with eight data bits has a total of 10 bits. Setting the M bit configures the SCI for nine-bit data characters. A frame with nine data bits has a total of 11 bits. Table 11-13. Example of 8-Bit Data Formats Start Bit Data Bits Address Bits Parity Bits Stop Bit 1 8 0 0 1 1 7 0 1 1 7 1 0 1 1 1 1 The address bit identifies the frame as an address character. See Section 11.4.6.6, "Receiver Wakeup". When the SCI is configured for 9-bit data characters, the ninth data bit is the T8 bit in SCI data register high (SCIDRH). It remains unchanged after transmission and can be used repeatedly without rewriting it. A frame with nine data bits has a total of 11 bits. Table 11-14. Example of 9-Bit Data Formats Start Bit Data Bits Address Bits Parity Bits Stop Bit 1 9 0 0 1 1 8 0 1 1 8 1 0 1 1 1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 495 Chapter 11 Serial Communication Interface (S12SCIV5) 1 11.4.4 The address bit identifies the frame as an address character. See Section 11.4.6.6, "Receiver Wakeup". Baud Rate Generation A 13-bit modulus counter in the baud rate generator derives the baud rate for both the receiver and the transmitter. The value from 0 to 8191 written to the SBR12:SBR0 bits determines the bus clock divisor. The SBR bits are in the SCI baud rate registers (SCIBDH and SCIBDL). The baud rate clock is synchronized with the bus clock and drives the receiver. The baud rate clock divided by 16 drives the transmitter. The receiver has an acquisition rate of 16 samples per bit time. Baud rate generation is subject to one source of error: * Integer division of the bus clock may not give the exact target frequency. Table 11-15 lists some examples of achieving target baud rates with a bus clock frequency of 25 MHz. When IREN = 0 then, SCI baud rate = SCI bus clock / (16 * SCIBR[12:0]) Table 11-15. Baud Rates (Example: Bus Clock = 25 MHz) Bits SBR[12:0] Receiver Clock (Hz) Transmitter Clock (Hz) Target Baud Rate Error (%) 41 609,756.1 38,109.8 38,400 .76 81 308,642.0 19,290.1 19,200 .47 163 153,374.2 9585.9 9,600 .16 326 76,687.1 4792.9 4,800 .15 651 38,402.5 2400.2 2,400 .01 1302 19,201.2 1200.1 1,200 .01 2604 9600.6 600.0 600 .00 5208 4800.0 300.0 300 .00 MC9S12XDP512 Data Sheet, Rev. 2.21 496 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.5 Transmitter Internal Bus Bus Clock / 16 Baud Divider SCI Data Registers 11-Bit Transmit Register H 8 7 6 5 4 3 2 1 0 TXPOL SCTXD L MSB M Start Stop SBR12:SBR0 LOOP CONTROL TIE TDRE IRQ Break (All 0s) Parity Generation Preamble (All 1s) PT Shift Enable PE Load from SCIDR T8 To Receiver LOOPS RSRC TDRE Transmitter Control TC TC IRQ TCIE TE BERRIF BER IRQ TCIE SBK BERRM[1:0] Transmit Collision Detect SCTXD SCRXD (From Receiver) Figure 11-16. Transmitter Block Diagram 11.4.5.1 Transmitter Character Length The SCI transmitter can accommodate either 8-bit or 9-bit data characters. The state of the M bit in SCI control register 1 (SCICR1) determines the length of data characters. When transmitting 9-bit data, bit T8 in SCI data register high (SCIDRH) is the ninth bit (bit 8). 11.4.5.2 Character Transmission To transmit data, the MCU writes the data bits to the SCI data registers (SCIDRH/SCIDRL), which in turn are transferred to the transmitter shift register. The transmit shift register then shifts a frame out through the TXD pin, after it has prefaced them with a start bit and appended them with a stop bit. The SCI data registers (SCIDRH and SCIDRL) are the write-only buffers between the internal data bus and the transmit shift register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 497 Chapter 11 Serial Communication Interface (S12SCIV5) The SCI also sets a flag, the transmit data register empty flag (TDRE), every time it transfers data from the buffer (SCIDRH/L) to the transmitter shift register.The transmit driver routine may respond to this flag by writing another byte to the Transmitter buffer (SCIDRH/SCIDRL), while the shift register is still shifting out the first byte. To initiate an SCI transmission: 1. Configure the SCI: a) Select a baud rate. Write this value to the SCI baud registers (SCIBDH/L) to begin the baud rate generator. Remember that the baud rate generator is disabled when the baud rate is zero. Writing to the SCIBDH has no effect without also writing to SCIBDL. b) Write to SCICR1 to configure word length, parity, and other configuration bits (LOOPS,RSRC,M,WAKE,ILT,PE,PT). c) Enable the transmitter, interrupts, receive, and wake up as required, by writing to the SCICR2 register bits (TIE,TCIE,RIE,ILIE,TE,RE,RWU,SBK). A preamble or idle character will now be shifted out of the transmitter shift register. 2. Transmit Procedure for each byte: a) Poll the TDRE flag by reading the SCISR1 or responding to the TDRE interrupt. Keep in mind that the TDRE bit resets to one. b) If the TDRE flag is set, write the data to be transmitted to SCIDRH/L, where the ninth bit is written to the T8 bit in SCIDRH if the SCI is in 9-bit data format. A new transmission will not result until the TDRE flag has been cleared. 3. Repeat step 2 for each subsequent transmission. NOTE The TDRE flag is set when the shift register is loaded with the next data to be transmitted from SCIDRH/L, which happens, generally speaking, a little over half-way through the stop bit of the previous frame. Specifically, this transfer occurs 9/16ths of a bit time AFTER the start of the stop bit of the previous frame. Writing the TE bit from 0 to a 1 automatically loads the transmit shift register with a preamble of 10 logic 1s (if M = 0) or 11 logic 1s (if M = 1). After the preamble shifts out, control logic transfers the data from the SCI data register into the transmit shift register. A logic 0 start bit automatically goes into the least significant bit position of the transmit shift register. A logic 1 stop bit goes into the most significant bit position. Hardware supports odd or even parity. When parity is enabled, the most significant bit (MSB) of the data character is the parity bit. The transmit data register empty flag, TDRE, in SCI status register 1 (SCISR1) becomes set when the SCI data register transfers a byte to the transmit shift register. The TDRE flag indicates that the SCI data register can accept new data from the internal data bus. If the transmit interrupt enable bit, TIE, in SCI control register 2 (SCICR2) is also set, the TDRE flag generates a transmitter interrupt request. MC9S12XDP512 Data Sheet, Rev. 2.21 498 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) When the transmit shift register is not transmitting a frame, the TXD pin goes to the idle condition, logic 1. If at any time software clears the TE bit in SCI control register 2 (SCICR2), the transmitter enable signal goes low and the transmit signal goes idle. If software clears TE while a transmission is in progress (TC = 0), the frame in the transmit shift register continues to shift out. To avoid accidentally cutting off the last frame in a message, always wait for TDRE to go high after the last frame before clearing TE. To separate messages with preambles with minimum idle line time, use this sequence between messages: 1. Write the last byte of the first message to SCIDRH/L. 2. Wait for the TDRE flag to go high, indicating the transfer of the last frame to the transmit shift register. 3. Queue a preamble by clearing and then setting the TE bit. 4. Write the first byte of the second message to SCIDRH/L. 11.4.5.3 Break Characters Writing a logic 1 to the send break bit, SBK, in SCI control register 2 (SCICR2) loads the transmit shift register with a break character. A break character contains all logic 0s and has no start, stop, or parity bit. Break character length depends on the M bit in SCI control register 1 (SCICR1). As long as SBK is at logic 1, transmitter logic continuously loads break characters into the transmit shift register. After software clears the SBK bit, the shift register finishes transmitting the last break character and then transmits at least one logic 1. The automatic logic 1 at the end of a break character guarantees the recognition of the start bit of the next frame. The SCI recognizes a break character when there are 10 or 11(M = 0 or M = 1) consecutive zero received. Depending if the break detect feature is enabled or not receiving a break character has these effects on SCI registers. If the break detect feature is disabled (BKDFE = 0): * Sets the framing error flag, FE * Sets the receive data register full flag, RDRF * Clears the SCI data registers (SCIDRH/L) * May set the overrun flag, OR, noise flag, NF, parity error flag, PE, or the receiver active flag, RAF (see 3.4.4 and 3.4.5 SCI Status Register 1 and 2) If the break detect feature is enabled (BKDFE = 1) there are two scenarios1 The break is detected right from a start bit or is detected during a byte reception. * Sets the break detect interrupt flag, BLDIF * Does not change the data register full flag, RDRF or overrun flag OR * Does not change the framing error flag FE, parity error flag PE. * Does not clear the SCI data registers (SCIDRH/L) * May set noise flag NF, or receiver active flag RAF. 1. A Break character in this context are either 10 or 11 consecutive zero received bits MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 499 Chapter 11 Serial Communication Interface (S12SCIV5) Figure 11-17 shows two cases of break detect. In trace RXD_1 the break symbol starts with the start bit, while in RXD_2 the break starts in the middle of a transmission. If BRKDFE = 1, in RXD_1 case there will be no byte transferred to the receive buffer and the RDRF flag will not be modified. Also no framing error or parity error will be flagged from this transfer. In RXD_2 case, however the break signal starts later during the transmission. At the expected stop bit position the byte received so far will be transferred to the receive buffer, the receive data register full flag will be set, a framing error and if enabled and appropriate a parity error will be set. Once the break is detected the BRKDIF flag will be set. Start Bit Position Stop Bit Position BRKDIF = 1 RXD_1 Zero Bit Counter 1 2 3 4 5 6 7 8 9 10 . . . BRKDIF = 1 FE = 1 RXD_2 Zero Bit Counter 1 2 3 4 5 6 7 8 9 10 ... Figure 11-17. Break Detection if BRKDFE = 1 (M = 0) 11.4.5.4 Idle Characters An idle character (or preamble) contains all logic 1s and has no start, stop, or parity bit. Idle character length depends on the M bit in SCI control register 1 (SCICR1). The preamble is a synchronizing idle character that begins the first transmission initiated after writing the TE bit from 0 to 1. If the TE bit is cleared during a transmission, the TXD pin becomes idle after completion of the transmission in progress. Clearing and then setting the TE bit during a transmission queues an idle character to be sent after the frame currently being transmitted. NOTE When queueing an idle character, return the TE bit to logic 1 before the stop bit of the current frame shifts out through the TXD pin. Setting TE after the stop bit appears on TXD causes data previously written to the SCI data register to be lost. Toggle the TE bit for a queued idle character while the TDRE flag is set and immediately before writing the next byte to the SCI data register. If the TE bit is clear and the transmission is complete, the SCI is not the master of the TXD pin MC9S12XDP512 Data Sheet, Rev. 2.21 500 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.5.5 LIN Transmit Collision Detection This module allows to check for collisions on the LIN bus. LIN Physical Interface Synchronizer Stage Receive Shift Register Compare RXD Pin Bit Error LIN Bus Bus Clock Sample Point Transmit Shift Register TXD Pin Figure 11-18. Collision Detect Principle If the bit error circuit is enabled (BERRM[1:0] = 0:1 or = 1:0]), the error detect circuit will compare the transmitted and the received data stream at a point in time and flag any mismatch. The timing checks run when transmitter is active (not idle). As soon as a mismatch between the transmitted data and the received data is detected the following happens: * The next bit transmitted will have a high level (TXPOL = 0) or low level (TXPOL = 1) * The transmission is aborted and the byte in transmit buffer is discarded. * the transmit data register empty and the transmission complete flag will be set * The bit error interrupt flag, BERRIF, will be set. * No further transmissions will take place until the BERRIF is cleared. 4 5 6 7 8 BERRM[1:0] = 0:1 9 10 11 12 13 14 15 0 Sampling End 3 Sampling Begin Input Receive Shift Register 2 Sampling End Output Transmit Shift Register 1 Sampling Begin 0 BERRM[1:0] = 1:1 Compare Sample Points Figure 11-19. Timing Diagram Bit Error Detection If the bit error detect feature is disabled, the bit error interrupt flag is cleared. NOTE The RXPOL and TXPOL bit should be set the same when transmission collision detect feature is enabled, otherwise the bit error interrupt flag may be set incorrectly. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 501 Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.6 Receiver Internal Bus SBR12:SBR0 RXPOL Data Recovery Loop Control H Start 11-Bit Receive Shift Register 8 7 6 5 4 3 2 1 0 L All 1s SCRXD From TXD Pin or Transmitter Stop Baud Divider MSB Bus Clock SCI Data Register RE RAF LOOPS RSRC FE M RWU NF WAKE ILT PE PT Wakeup Logic PE R8 Parity Checking Idle IRQ IDLE ILIE BRKDFE OR Break Detect Logic RIE BRKDIF BRKDIE Active Edge Detect Logic RDRF/OR IRQ RDRF Break IRQ RXEDGIF RXEDGIE RX Active Edge IRQ Figure 11-20. SCI Receiver Block Diagram 11.4.6.1 Receiver Character Length The SCI receiver can accommodate either 8-bit or 9-bit data characters. The state of the M bit in SCI control register 1 (SCICR1) determines the length of data characters. When receiving 9-bit data, bit R8 in SCI data register high (SCIDRH) is the ninth bit (bit 8). 11.4.6.2 Character Reception During an SCI reception, the receive shift register shifts a frame in from the RXD pin. The SCI data register is the read-only buffer between the internal data bus and the receive shift register. After a complete frame shifts into the receive shift register, the data portion of the frame transfers to the SCI data register. The receive data register full flag, RDRF, in SCI status register 1 (SCISR1) becomes set, MC9S12XDP512 Data Sheet, Rev. 2.21 502 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) indicating that the received byte can be read. If the receive interrupt enable bit, RIE, in SCI control register 2 (SCICR2) is also set, the RDRF flag generates an RDRF interrupt request. 11.4.6.3 Data Sampling The RT clock rate. The RT clock is an internal signal with a frequency 16 times the baud rate. To adjust for baud rate mismatch, the RT clock (see Figure 11-21) is re-synchronized: * After every start bit * After the receiver detects a data bit change from logic 1 to logic 0 (after the majority of data bit samples at RT8, RT9, and RT10 returns a valid logic 1 and the majority of the next RT8, RT9, and RT10 samples returns a valid logic 0) To locate the start bit, data recovery logic does an asynchronous search for a logic 0 preceded by three logic 1s.When the falling edge of a possible start bit occurs, the RT clock begins to count to 16. Start Bit LSB RXD Samples 1 1 1 1 1 1 1 1 0 0 Start Bit Qualification 0 0 Start Bit Verification 0 0 0 Data Sampling RT4 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT CLock Count RT1 RT Clock Reset RT Clock Figure 11-21. Receiver Data Sampling To verify the start bit and to detect noise, data recovery logic takes samples at RT3, RT5, and RT7. Figure 11-16 summarizes the results of the start bit verification samples. Table 11-16. Start Bit Verification RT3, RT5, and RT7 Samples Start Bit Verification Noise Flag 000 Yes 0 001 Yes 1 010 Yes 1 011 No 0 100 Yes 1 101 No 0 110 No 0 111 No 0 If start bit verification is not successful, the RT clock is reset and a new search for a start bit begins. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 503 Chapter 11 Serial Communication Interface (S12SCIV5) To determine the value of a data bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 11-17 summarizes the results of the data bit samples. Table 11-17. Data Bit Recovery RT8, RT9, and RT10 Samples Data Bit Determination Noise Flag 000 0 0 001 0 1 010 0 1 011 1 1 100 0 1 101 1 1 110 1 1 111 1 0 NOTE The RT8, RT9, and RT10 samples do not affect start bit verification. If any or all of the RT8, RT9, and RT10 start bit samples are logic 1s following a successful start bit verification, the noise flag (NF) is set and the receiver assumes that the bit is a start bit (logic 0). To verify a stop bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 11-18 summarizes the results of the stop bit samples. Table 11-18. Stop Bit Recovery RT8, RT9, and RT10 Samples Framing Error Flag Noise Flag 000 1 0 001 1 1 010 1 1 011 0 1 100 1 1 101 0 1 110 0 1 111 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 504 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) In Figure 11-22 the verification samples RT3 and RT5 determine that the first low detected was noise and not the beginning of a start bit. The RT clock is reset and the start bit search begins again. The noise flag is not set because the noise occurred before the start bit was found. LSB Start Bit 0 0 0 0 0 0 RT9 1 RT10 RT1 1 RT8 RT1 1 RT7 0 RT1 1 RT1 1 RT5 1 RT1 Samples RT1 RXD 0 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT6 RT5 RT4 RT3 RT2 RT4 RT3 RT Clock Count RT2 RT Clock Reset RT Clock Figure 11-22. Start Bit Search Example 1 In Figure 11-23, verification sample at RT3 is high. The RT3 sample sets the noise flag. Although the perceived bit time is misaligned, the data samples RT8, RT9, and RT10 are within the bit time and data recovery is successful. Perceived Start Bit LSB Actual Start Bit 1 0 RT1 RT1 RT1 RT1 RT1 1 0 0 0 0 0 RT10 1 RT9 1 RT8 1 RT7 1 RT1 RXD Samples RT7 RT6 RT5 RT4 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT6 RT5 RT4 RT3 RT Clock Count RT2 RT Clock Reset RT Clock Figure 11-23. Start Bit Search Example 2 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 505 Chapter 11 Serial Communication Interface (S12SCIV5) In Figure 11-24, a large burst of noise is perceived as the beginning of a start bit, although the test sample at RT5 is high. The RT5 sample sets the noise flag. Although this is a worst-case misalignment of perceived bit time, the data samples RT8, RT9, and RT10 are within the bit time and data recovery is successful. Perceived Start Bit LSB Actual Start Bit RT1 RT1 0 1 0 0 0 0 RT10 0 RT9 1 RT8 1 RT7 1 RT1 Samples RT1 RXD RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT6 RT5 RT4 RT3 RT Clock Count RT2 RT Clock Reset RT Clock Figure 11-24. Start Bit Search Example 3 Figure 11-25 shows the effect of noise early in the start bit time. Although this noise does not affect proper synchronization with the start bit time, it does set the noise flag. LSB Perceived and Actual Start Bit RT1 RT1 RT1 1 1 1 1 0 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT1 Samples RT1 RXD 1 0 RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT9 RT10 RT8 RT7 RT6 RT5 RT4 RT3 RT Clock Count RT2 RT Clock Reset RT Clock Figure 11-25. Start Bit Search Example 4 MC9S12XDP512 Data Sheet, Rev. 2.21 506 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) Figure 11-26 shows a burst of noise near the beginning of the start bit that resets the RT clock. The sample after the reset is low but is not preceded by three high samples that would qualify as a falling edge. Depending on the timing of the start bit search and on the data, the frame may be missed entirely or it may set the framing error flag. Start Bit 0 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 0 1 1 0 0 0 0 0 0 0 0 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT1 1 RT7 1 RT1 Samples LSB No Start Bit Found RXD RT1 RT1 RT1 RT1 RT6 RT5 RT4 RT3 RT Clock Count RT2 RT Clock Reset RT Clock Figure 11-26. Start Bit Search Example 5 In Figure 11-27, a noise burst makes the majority of data samples RT8, RT9, and RT10 high. This sets the noise flag but does not reset the RT clock. In start bits only, the RT8, RT9, and RT10 data samples are ignored. Start Bit LSB 1 1 1 1 1 0 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 0 0 0 1 0 1 RT10 1 RT9 1 RT8 1 RT7 1 RT1 Samples RT1 RXD RT3 RT2 RT1 RT16 RT15 RT14 RT13 RT12 RT11 RT6 RT5 RT4 RT3 RT Clock Count RT2 RT Clock Reset RT Clock Figure 11-27. Start Bit Search Example 6 11.4.6.4 Framing Errors If the data recovery logic does not detect a logic 1 where the stop bit should be in an incoming frame, it sets the framing error flag, FE, in SCI status register 1 (SCISR1). A break character also sets the FE flag because a break character has no stop bit. The FE flag is set at the same time that the RDRF flag is set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 507 Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.6.5 Baud Rate Tolerance A transmitting device may be operating at a baud rate below or above the receiver baud rate. Accumulated bit time misalignment can cause one of the three stop bit data samples (RT8, RT9, and RT10) to fall outside the actual stop bit. A noise error will occur if the RT8, RT9, and RT10 samples are not all the same logical values. A framing error will occur if the receiver clock is misaligned in such a way that the majority of the RT8, RT9, and RT10 stop bit samples are a logic zero. As the receiver samples an incoming frame, it re-synchronizes the RT clock on any valid falling edge within the frame. Re synchronization within frames will correct a misalignment between transmitter bit times and receiver bit times. 11.4.6.5.1 Slow Data Tolerance Figure 11-28 shows how much a slow received frame can be misaligned without causing a noise error or a framing error. The slow stop bit begins at RT8 instead of RT1 but arrives in time for the stop bit data samples at RT8, RT9, and RT10. MSB Stop RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 Receiver RT Clock Data Samples Figure 11-28. Slow Data Let's take RTr as receiver RT clock and RTt as transmitter RT clock. For an 8-bit data character, it takes the receiver 9 bit times x 16 RTr cycles +7 RTr cycles = 151 RTr cycles to start data sampling of the stop bit. With the misaligned character shown in Figure 11-28, the receiver counts 151 RTr cycles at the point when the count of the transmitting device is 9 bit times x 16 RTt cycles = 144 RTt cycles. The maximum percent difference between the receiver count and the transmitter count of a slow 8-bit data character with no errors is: ((151 - 144) / 151) x 100 = 4.63% For a 9-bit data character, it takes the receiver 10 bit times x 16 RTr cycles + 7 RTr cycles = 167 RTr cycles to start data sampling of the stop bit. With the misaligned character shown in Figure 11-28, the receiver counts 167 RTr cycles at the point when the count of the transmitting device is 10 bit times x 16 RTt cycles = 160 RTt cycles. The maximum percent difference between the receiver count and the transmitter count of a slow 9-bit character with no errors is: ((167 - 160) / 167) X 100 = 4.19% MC9S12XDP512 Data Sheet, Rev. 2.21 508 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.6.5.2 Fast Data Tolerance Figure 11-29 shows how much a fast received frame can be misaligned. The fast stop bit ends at RT10 instead of RT16 but is still sampled at RT8, RT9, and RT10. Stop Idle or Next Frame RT16 RT15 RT14 RT13 RT12 RT11 RT10 RT9 RT8 RT7 RT6 RT5 RT4 RT3 RT2 RT1 Receiver RT Clock Data Samples Figure 11-29. Fast Data For an 8-bit data character, it takes the receiver 9 bit times x 16 RTr cycles + 10 RTr cycles = 154 RTr cycles to finish data sampling of the stop bit. With the misaligned character shown in Figure 11-29, the receiver counts 154 RTr cycles at the point when the count of the transmitting device is 10 bit times x 16 RTt cycles = 160 RTt cycles. The maximum percent difference between the receiver count and the transmitter count of a fast 8-bit character with no errors is: ((160 - 154) / 160) x 100 = 3.75% For a 9-bit data character, it takes the receiver 10 bit times x 16 RTr cycles + 10 RTr cycles = 170 RTr cycles to finish data sampling of the stop bit. With the misaligned character shown in Figure 11-29, the receiver counts 170 RTr cycles at the point when the count of the transmitting device is 11 bit times x 16 RTt cycles = 176 RTt cycles. The maximum percent difference between the receiver count and the transmitter count of a fast 9-bit character with no errors is: ((176 - 170) /176) x 100 = 3.40% 11.4.6.6 Receiver Wakeup To enable the SCI to ignore transmissions intended only for other receivers in multiple-receiver systems, the receiver can be put into a standby state. Setting the receiver wakeup bit, RWU, in SCI control register 2 (SCICR2) puts the receiver into standby state during which receiver interrupts are disabled.The SCI will still load the receive data into the SCIDRH/L registers, but it will not set the RDRF flag. The transmitting device can address messages to selected receivers by including addressing information in the initial frame or frames of each message. The WAKE bit in SCI control register 1 (SCICR1) determines how the SCI is brought out of the standby state to process an incoming message. The WAKE bit enables either idle line wakeup or address mark wakeup. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 509 Chapter 11 Serial Communication Interface (S12SCIV5) 11.4.6.6.1 Idle Input line Wakeup (WAKE = 0) In this wakeup method, an idle condition on the RXD pin clears the RWU bit and wakes up the SCI. The initial frame or frames of every message contain addressing information. All receivers evaluate the addressing information, and receivers for which the message is addressed process the frames that follow. Any receiver for which a message is not addressed can set its RWU bit and return to the standby state. The RWU bit remains set and the receiver remains on standby until another idle character appears on the RXD pin. Idle line wakeup requires that messages be separated by at least one idle character and that no message contains idle characters. The idle character that wakes a receiver does not set the receiver idle bit, IDLE, or the receive data register full flag, RDRF. The idle line type bit, ILT, determines whether the receiver begins counting logic 1s as idle character bits after the start bit or after the stop bit. ILT is in SCI control register 1 (SCICR1). 11.4.6.6.2 Address Mark Wakeup (WAKE = 1) In this wakeup method, a logic 1 in the most significant bit (MSB) position of a frame clears the RWU bit and wakes up the SCI. The logic 1 in the MSB position marks a frame as an address frame that contains addressing information. All receivers evaluate the addressing information, and the receivers for which the message is addressed process the frames that follow.Any receiver for which a message is not addressed can set its RWU bit and return to the standby state. The RWU bit remains set and the receiver remains on standby until another address frame appears on the RXD pin. The logic 1 MSB of an address frame clears the receiver's RWU bit before the stop bit is received and sets the RDRF flag. Address mark wakeup allows messages to contain idle characters but requires that the MSB be reserved for use in address frames. NOTE With the WAKE bit clear, setting the RWU bit after the RXD pin has been idle can cause the receiver to wake up immediately. 11.4.7 Single-Wire Operation Normally, the SCI uses two pins for transmitting and receiving. In single-wire operation, the RXD pin is disconnected from the SCI. The SCI uses the TXD pin for both receiving and transmitting. Transmitter Receiver TXD RXD Figure 11-30. Single-Wire Operation (LOOPS = 1, RSRC = 1) MC9S12XDP512 Data Sheet, Rev. 2.21 510 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) Enable single-wire operation by setting the LOOPS bit and the receiver source bit, RSRC, in SCI control register 1 (SCICR1). Setting the LOOPS bit disables the path from the RXD pin to the receiver. Setting the RSRC bit connects the TXD pin to the receiver. Both the transmitter and receiver must be enabled (TE = 1 and RE = 1).The TXDIR bit (SCISR2[1]) determines whether the TXD pin is going to be used as an input (TXDIR = 0) or an output (TXDIR = 1) in this mode of operation. NOTE In single-wire operation data from the TXD pin is inverted if RXPOL is set. 11.4.8 Loop Operation In loop operation the transmitter output goes to the receiver input. The RXD pin is disconnected from the SCI. Transmitter TXD Receiver RXD Figure 11-31. Loop Operation (LOOPS = 1, RSRC = 0) Enable loop operation by setting the LOOPS bit and clearing the RSRC bit in SCI control register 1 (SCICR1). Setting the LOOPS bit disables the path from the RXD pin to the receiver. Clearing the RSRC bit connects the transmitter output to the receiver input. Both the transmitter and receiver must be enabled (TE = 1 and RE = 1). NOTE In loop operation data from the transmitter is not recognized by the receiver if RXPOL and TXPOL are not the same. 11.5 Initialization/Application Information 11.5.1 Reset Initialization See Section 11.3.2, "Register Descriptions". 11.5.2 11.5.2.1 Modes of Operation Run Mode Normal mode of operation. To initialize a SCI transmission, see Section 11.4.5.2, "Character Transmission". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 511 Chapter 11 Serial Communication Interface (S12SCIV5) 11.5.2.2 Wait Mode SCI operation in wait mode depends on the state of the SCISWAI bit in the SCI control register 1 (SCICR1). * If SCISWAI is clear, the SCI operates normally when the CPU is in wait mode. * If SCISWAI is set, SCI clock generation ceases and the SCI module enters a power-conservation state when the CPU is in wait mode. Setting SCISWAI does not affect the state of the receiver enable bit, RE, or the transmitter enable bit, TE. If SCISWAI is set, any transmission or reception in progress stops at wait mode entry. The transmission or reception resumes when either an internal or external interrupt brings the CPU out of wait mode. Exiting wait mode by reset aborts any transmission or reception in progress and resets the SCI. 11.5.2.3 Stop Mode The SCI is inactive during stop mode for reduced power consumption. The STOP instruction does not affect the SCI register states, but the SCI bus clock will be disabled. The SCI operation resumes from where it left off after an external interrupt brings the CPU out of stop mode. Exiting stop mode by reset aborts any transmission or reception in progress and resets the SCI. The receive input active edge detect circuit is still active in stop mode. An active edge on the receive input can be used to bring the CPU out of stop mode. 11.5.3 Interrupt Operation This section describes the interrupt originated by the SCI block.The MCU must service the interrupt requests. Table 11-19 lists the eight interrupt sources of the SCI. Table 11-19. SCI Interrupt Sources Interrupt Source Local Enable TDRE SCISR1[7] TIE TC SCISR1[6] TCIE RDRF SCISR1[5] RIE OR SCISR1[3] IDLE SCISR1[4] RXEDGIF SCIASR1[7] Description Active high level. Indicates that a byte was transferred from SCIDRH/L to the transmit shift register. Active high level. Indicates that a transmit is complete. Active high level. The RDRF interrupt indicates that received data is available in the SCI data register. Active high level. This interrupt indicates that an overrun condition has occurred. ILIE RXEDGIE Active high level. Indicates that receiver input has become idle. Active high level. Indicates that an active edge (falling for RXPOL = 0, rising for RXPOL = 1) was detected. BERRIF SCIASR1[1] BERRIE Active high level. Indicates that a mismatch between transmitted and received data in a single wire application has happened. BKDIF SCIASR1[0] BRKDIE Active high level. Indicates that a break character has been received. MC9S12XDP512 Data Sheet, Rev. 2.21 512 Freescale Semiconductor Chapter 11 Serial Communication Interface (S12SCIV5) 11.5.3.1 Description of Interrupt Operation The SCI only originates interrupt requests. The following is a description of how the SCI makes a request and how the MCU should acknowledge that request. The interrupt vector offset and interrupt number are chip dependent. The SCI only has a single interrupt line (SCI Interrupt Signal, active high operation) and all the following interrupts, when generated, are ORed together and issued through that port. 11.5.3.1.1 TDRE Description The TDRE interrupt is set high by the SCI when the transmit shift register receives a byte from the SCI data register. A TDRE interrupt indicates that the transmit data register (SCIDRH/L) is empty and that a new byte can be written to the SCIDRH/L for transmission.Clear TDRE by reading SCI status register 1 with TDRE set and then writing to SCI data register low (SCIDRL). 11.5.3.1.2 TC Description The TC interrupt is set by the SCI when a transmission has been completed. Transmission is completed when all bits including the stop bit (if transmitted) have been shifted out and no data is queued to be transmitted. No stop bit is transmitted when sending a break character and the TC flag is set (providing there is no more data queued for transmission) when the break character has been shifted out. A TC interrupt indicates that there is no transmission in progress. TC is set high when the TDRE flag is set and no data, preamble, or break character is being transmitted. When TC is set, the TXD pin becomes idle (logic 1). Clear TC by reading SCI status register 1 (SCISR1) with TC set and then writing to SCI data register low (SCIDRL).TC is cleared automatically when data, preamble, or break is queued and ready to be sent. 11.5.3.1.3 RDRF Description The RDRF interrupt is set when the data in the receive shift register transfers to the SCI data register. A RDRF interrupt indicates that the received data has been transferred to the SCI data register and that the byte can now be read by the MCU. The RDRF interrupt is cleared by reading the SCI status register one (SCISR1) and then reading SCI data register low (SCIDRL). 11.5.3.1.4 OR Description The OR interrupt is set when software fails to read the SCI data register before the receive shift register receives the next frame. The newly acquired data in the shift register will be lost in this case, but the data already in the SCI data registers is not affected. The OR interrupt is cleared by reading the SCI status register one (SCISR1) and then reading SCI data register low (SCIDRL). 11.5.3.1.5 IDLE Description The IDLE interrupt is set when 10 consecutive logic 1s (if M = 0) or 11 consecutive logic 1s (if M = 1) appear on the receiver input. Once the IDLE is cleared, a valid frame must again set the RDRF flag before an idle condition can set the IDLE flag. Clear IDLE by reading SCI status register 1 (SCISR1) with IDLE set and then reading SCI data register low (SCIDRL). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 513 Chapter 11 Serial Communication Interface (S12SCIV5) 11.5.3.1.6 RXEDGIF Description The RXEDGIF interrupt is set when an active edge (falling if RXPOL = 0, rising if RXPOL = 1) on the RXD pin is detected. Clear RXEDGIF by writing a "1" to the SCIASR1 SCI alternative status register 1. 11.5.3.1.7 BERRIF Description The BERRIF interrupt is set when a mismatch between the transmitted and the received data in a single wire application like LIN was detected. Clear BERRIF by writing a "1" to the SCIASR1 SCI alternative status register 1. This flag is also cleared if the bit error detect feature is disabled. 11.5.3.1.8 BKDIF Description The BKDIF interrupt is set when a break signal was received. Clear BKDIF by writing a "1" to the SCIASR1 SCI alternative status register 1. This flag is also cleared if break detect feature is disabled. 11.5.4 Recovery from Wait Mode The SCI interrupt request can be used to bring the CPU out of wait mode. 11.5.5 Recovery from Stop Mode An active edge on the receive input can be used to bring the CPU out of stop mode. MC9S12XDP512 Data Sheet, Rev. 2.21 514 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.1 Introduction The SPI module allows a duplex, synchronous, serial communication between the MCU and peripheral devices. Software can poll the SPI status flags or the SPI operation can be interrupt driven. 12.1.1 Glossary of Terms SPI SS SCK MOSI MISO MOMI SISO 12.1.2 Serial Peripheral Interface Slave Select Serial Clock Master Output, Slave Input Master Input, Slave Output Master Output, Master Input Slave Input, Slave Output Features The SPI includes these distinctive features: * Master mode and slave mode * Bidirectional mode * Slave select output * Mode fault error flag with CPU interrupt capability * Double-buffered data register * Serial clock with programmable polarity and phase * Control of SPI operation during wait mode 12.1.3 Modes of Operation The SPI functions in three modes: run, wait, and stop. * Run mode This is the basic mode of operation. * Wait mode MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 515 Chapter 12 Serial Peripheral Interface (S12SPIV4) * SPI operation in wait mode is a configurable low power mode, controlled by the SPISWAI bit located in the SPICR2 register. In wait mode, if the SPISWAI bit is clear, the SPI operates like in run mode. If the SPISWAI bit is set, the SPI goes into a power conservative state, with the SPI clock generation turned off. If the SPI is configured as a master, any transmission in progress stops, but is resumed after CPU goes into run mode. If the SPI is configured as a slave, reception and transmission of a byte continues, so that the slave stays synchronized to the master. Stop mode The SPI is inactive in stop mode for reduced power consumption. If the SPI is configured as a master, any transmission in progress stops, but is resumed after CPU goes into run mode. If the SPI is configured as a slave, reception and transmission of a byte continues, so that the slave stays synchronized to the master. This is a high level description only, detailed descriptions of operating modes are contained in Section 12.4.7, "Low Power Mode Options". 12.1.4 Block Diagram Figure 12-1 gives an overview on the SPI architecture. The main parts of the SPI are status, control and data registers, shifter logic, baud rate generator, master/slave control logic, and port control logic. MC9S12XDP512 Data Sheet, Rev. 2.21 516 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) SPI 2 SPI Control Register 1 BIDIROE 2 SPI Control Register 2 SPC0 SPI Status Register Slave Control SPIF MODF SPTEF CPOL CPHA Phase + SCK In Slave Baud Rate Polarity Control Master Baud Rate Phase + SCK Out Polarity Control Interrupt Control SPI Interrupt Request Baud Rate Generator Master Control Counter Bus Clock 3 SPR Port Control Logic SCK SS Prescaler Clock Select SPPR MOSI Baud Rate Shift Clock Sample Clock 3 Shifter SPI Baud Rate Register Data In LSBFE=1 LSBFE=0 8 SPI Data Register 8 LSBFE=1 MSB LSBFE=0 LSBFE=0 LSB LSBFE=1 Data Out Figure 12-1. SPI Block Diagram 12.2 External Signal Description This section lists the name and description of all ports including inputs and outputs that do, or may, connect off chip. The SPI module has a total of four external pins. 12.2.1 MOSI -- Master Out/Slave In Pin This pin is used to transmit data out of the SPI module when it is configured as a master and receive data when it is configured as slave. 12.2.2 MISO -- Master In/Slave Out Pin This pin is used to transmit data out of the SPI module when it is configured as a slave and receive data when it is configured as master. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 517 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.2.3 SS -- Slave Select Pin This pin is used to output the select signal from the SPI module to another peripheral with which a data transfer is to take place when it is configured as a master and it is used as an input to receive the slave select signal when the SPI is configured as slave. 12.2.4 SCK -- Serial Clock Pin In master mode, this is the synchronous output clock. In slave mode, this is the synchronous input clock. 12.3 Memory Map and Register Definition This section provides a detailed description of address space and registers used by the SPI. 12.3.1 Module Memory Map The memory map for the SPI is given in Figure 12-2. The address listed for each register is the sum of a base address and an address offset. The base address is defined at the SoC level and the address offset is defined at the module level. Reads from the reserved bits return zeros and writes to the reserved bits have no effect. Register Name Bit 7 6 5 4 3 2 1 Bit 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0 0 MODFEN BIDIROE SPISWAI SPC0 SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 SPICR1 R W SPICR2 R W 0 SPIBR R W 0 SPISR R W SPIF 0 SPTEF MODF 0 0 0 0 Reserved R W SPIDR R W Bit 7 6 5 4 3 2 1 Bit 0 Reserved R W Reserved R W 0 0 = Unimplemented or Reserved Figure 12-2. SPI Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 518 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.3.2 Register Descriptions This section consists of register descriptions in address order. Each description includes a standard register diagram with an associated figure number. Details of register bit and field function follow the register diagrams, in bit order. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 519 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.3.2.1 R W Reset SPI Control Register 1 (SPICR1) 7 6 5 4 3 2 1 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0 0 0 0 0 1 0 0 Figure 12-3. SPI Control Register 1 (SPICR1) Read: Anytime Write: Anytime Table 12-1. SPICR1 Field Descriptions Field Description 7 SPIE SPI Interrupt Enable Bit -- This bit enables SPI interrupt requests, if SPIF or MODF status flag is set. 0 SPI interrupts disabled. 1 SPI interrupts enabled. 6 SPE SPI System Enable Bit -- This bit enables the SPI system and dedicates the SPI port pins to SPI system functions. If SPE is cleared, SPI is disabled and forced into idle state, status bits in SPISR register are reset. 0 SPI disabled (lower power consumption). 1 SPI enabled, port pins are dedicated to SPI functions. 5 SPTIE SPI Transmit Interrupt Enable -- This bit enables SPI interrupt requests, if SPTEF flag is set. 0 SPTEF interrupt disabled. 1 SPTEF interrupt enabled. 4 MSTR SPI Master/Slave Mode Select Bit -- This bit selects whether the SPI operates in master or slave mode. Switching the SPI from master to slave or vice versa forces the SPI system into idle state. 0 SPI is in slave mode. 1 SPI is in master mode. 3 CPOL SPI Clock Polarity Bit -- This bit selects an inverted or non-inverted SPI clock. To transmit data between SPI modules, the SPI modules must have identical CPOL values. In master mode, a change of this bit will abort a transmission in progress and force the SPI system into idle state. 0 Active-high clocks selected. In idle state SCK is low. 1 Active-low clocks selected. In idle state SCK is high. 2 CPHA SPI Clock Phase Bit -- This bit is used to select the SPI clock format. In master mode, a change of this bit will abort a transmission in progress and force the SPI system into idle state. 0 Sampling of data occurs at odd edges (1,3,5,...,15) of the SCK clock. 1 Sampling of data occurs at even edges (2,4,6,...,16) of the SCK clock. 1 SSOE Slave Select Output Enable -- The SS output feature is enabled only in master mode, if MODFEN is set, by asserting the SSOE as shown in Table 12-2. In master mode, a change of this bit will abort a transmission in progress and force the SPI system into idle state. 0 LSBFE LSB-First Enable -- This bit does not affect the position of the MSB and LSB in the data register. Reads and writes of the data register always have the MSB in bit 7. In master mode, a change of this bit will abort a transmission in progress and force the SPI system into idle state. 0 Data is transferred most significant bit first. 1 Data is transferred least significant bit first. MC9S12XDP512 Data Sheet, Rev. 2.21 520 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) Table 12-2. SS Input / Output Selection 12.3.2.2 R MODFEN SSOE Master Mode Slave Mode 0 0 SS not used by SPI SS input 0 1 SS not used by SPI SS input 1 0 SS input with MODF feature SS input 1 1 SS is slave select output SS input SPI Control Register 2 (SPICR2) 7 6 5 0 0 0 0 0 0 W Reset 4 3 MODFEN BIDIROE 0 0 2 0 0 1 0 SPISWAI SPC0 0 0 = Unimplemented or Reserved Figure 12-4. SPI Control Register 2 (SPICR2) Read: Anytime Write: Anytime; writes to the reserved bits have no effect Table 12-3. SPICR2 Field Descriptions Field Description 4 MODFEN Mode Fault Enable Bit -- This bit allows the MODF failure to be detected. If the SPI is in master mode and MODFEN is cleared, then the SS port pin is not used by the SPI. In slave mode, the SS is available only as an input regardless of the value of MODFEN. For an overview on the impact of the MODFEN bit on the SS port pin configuration, refer to Table 12-4. In master mode, a change of this bit will abort a transmission in progress and force the SPI system into idle state. 0 SS port pin is not used by the SPI. 1 SS port pin with MODF feature. 3 BIDIROE Output Enable in the Bidirectional Mode of Operation -- This bit controls the MOSI and MISO output buffer of the SPI, when in bidirectional mode of operation (SPC0 is set). In master mode, this bit controls the output buffer of the MOSI port, in slave mode it controls the output buffer of the MISO port. In master mode, with SPC0 set, a change of this bit will abort a transmission in progress and force the SPI into idle state. 0 Output buffer disabled. 1 Output buffer enabled. 1 SPISWAI SPI Stop in Wait Mode Bit -- This bit is used for power conservation while in wait mode. 0 SPI clock operates normally in wait mode. 1 Stop SPI clock generation when in wait mode. 0 SPC0 Serial Pin Control Bit 0 -- This bit enables bidirectional pin configurations as shown in Table 12-4. In master mode, a change of this bit will abort a transmission in progress and force the SPI system into idle state. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 521 Chapter 12 Serial Peripheral Interface (S12SPIV4) Table 12-4. Bidirectional Pin Configurations Pin Mode SPC0 BIDIROE MISO MOSI Master Mode of Operation Normal 0 Bidirectional 1 X Master In Master Out 0 MISO not used by SPI Master In 1 Master I/O Slave Mode of Operation 12.3.2.3 Normal 0 Bidirectional 1 6 0 W Reset Slave Out Slave In 0 Slave In MOSI not used by SPI 1 Slave I/O SPI Baud Rate Register (SPIBR) 7 R X 0 5 4 3 SPPR2 SPPR1 SPPR0 0 0 0 0 0 2 1 0 SPR2 SPR1 SPR0 0 0 0 = Unimplemented or Reserved Figure 12-5. SPI Baud Rate Register (SPIBR) Read: Anytime Write: Anytime; writes to the reserved bits have no effect Table 12-5. SPIBR Field Descriptions Field Description 6-4 SPPR[2:0] SPI Baud Rate Preselection Bits -- These bits specify the SPI baud rates as shown in Table 12-6. In master mode, a change of these bits will abort a transmission in progress and force the SPI system into idle state. 2-0 SPR[2:0] SPI Baud Rate Selection Bits -- These bits specify the SPI baud rates as shown in Table 12-6. In master mode, a change of these bits will abort a transmission in progress and force the SPI system into idle state. The baud rate divisor equation is as follows: BaudRateDivisor = (SPPR + 1) * 2(SPR + 1) Eqn. 12-1 The baud rate can be calculated with the following equation: Baud Rate = BusClock / BaudRateDivisor Eqn. 12-2 NOTE For maximum allowed baud rates, please refer to the SPI Electrical Specification in the Electricals chapter of this data sheet. MC9S12XDP512 Data Sheet, Rev. 2.21 522 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) Table 12-6. Example SPI Baud Rate Selection (25 MHz Bus Clock) SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 Baud Rate Divisor Baud Rate 0 0 0 0 0 0 2 12.5 MHz 0 0 0 0 0 1 4 6.25 MHz 0 0 0 0 1 0 8 3.125 MHz 0 0 0 0 1 1 16 1.5625 MHz 0 0 0 1 0 0 32 781.25 kHz 0 0 0 1 0 1 64 390.63 kHz 0 0 0 1 1 0 128 195.31 kHz 0 0 0 1 1 1 256 97.66 kHz 0 0 1 0 0 0 4 6.25 MHz 0 0 1 0 0 1 8 3.125 MHz 0 0 1 0 1 0 16 1.5625 MHz 0 0 1 0 1 1 32 781.25 kHz 0 0 1 1 0 0 64 390.63 kHz 0 0 1 1 0 1 128 195.31 kHz 0 0 1 1 1 0 256 97.66 kHz 0 0 1 1 1 1 512 48.83 kHz 0 1 0 0 0 0 6 4.16667 MHz 0 1 0 0 0 1 12 2.08333 MHz 0 1 0 0 1 0 24 1.04167 MHz 0 1 0 0 1 1 48 520.83 kHz 0 1 0 1 0 0 96 260.42 kHz 0 1 0 1 0 1 192 130.21 kHz 0 1 0 1 1 0 384 65.10 kHz 0 1 0 1 1 1 768 32.55 kHz 0 1 1 0 0 0 8 3.125 MHz 0 1 1 0 0 1 16 1.5625 MHz 0 1 1 0 1 0 32 781.25 kHz 0 1 1 0 1 1 64 390.63 kHz 0 1 1 1 0 0 128 195.31 kHz 0 1 1 1 0 1 256 97.66 kHz 0 1 1 1 1 0 512 48.83 kHz 0 1 1 1 1 1 1024 24.41 kHz 1 0 0 0 0 0 10 2.5 MHz 1 0 0 0 0 1 20 1.25 MHz 1 0 0 0 1 0 40 625 kHz 1 0 0 0 1 1 80 312.5 kHz 1 0 0 1 0 0 160 156.25 kHz 1 0 0 1 0 1 320 78.13 kHz 1 0 0 1 1 0 640 39.06 kHz MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 523 Chapter 12 Serial Peripheral Interface (S12SPIV4) Table 12-6. Example SPI Baud Rate Selection (25 MHz Bus Clock) (continued) SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 Baud Rate Divisor Baud Rate 1 0 0 1 1 1 1280 19.53 kHz 1 0 1 0 0 0 12 2.08333 MHz 1 0 1 0 0 1 24 1.04167 MHz 1 0 1 0 1 0 48 520.83 kHz 1 0 1 0 1 1 96 260.42 kHz 1 0 1 1 0 0 192 130.21 kHz 1 0 1 1 0 1 384 65.10 kHz 1 0 1 1 1 0 768 32.55 kHz 1 0 1 1 1 1 1536 16.28 kHz 1 1 0 0 0 0 14 1.78571 MHz 1 1 0 0 0 1 28 892.86 kHz 1 1 0 0 1 0 56 446.43 kHz 1 1 0 0 1 1 112 223.21 kHz 1 1 0 1 0 0 224 111.61 kHz 1 1 0 1 0 1 448 55.80 kHz 1 1 0 1 1 0 896 27.90 kHz 1 1 0 1 1 1 1792 13.95 kHz 1 1 1 0 0 0 16 1.5625 MHz 1 1 1 0 0 1 32 781.25 kHz 1 1 1 0 1 0 64 390.63 kHz 1 1 1 0 1 1 128 195.31 kHz 1 1 1 1 0 0 256 97.66 kHz 1 1 1 1 0 1 512 48.83 kHz 1 1 1 1 1 0 1024 24.41 kHz 1 1 1 1 1 1 2048 12.21 kHz MC9S12XDP512 Data Sheet, Rev. 2.21 524 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.3.2.4 R SPI Status Register (SPISR) 7 6 5 4 3 2 1 0 SPIF 0 SPTEF MODF 0 0 0 0 0 0 1 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 12-6. SPI Status Register (SPISR) Read: Anytime Write: Has no effect Table 12-7. SPISR Field Descriptions Field Description 7 SPIF SPIF Interrupt Flag -- This bit is set after a received data byte has been transferred into the SPI data register. This bit is cleared by reading the SPISR register (with SPIF set) followed by a read access to the SPI data register. 0 Transfer not yet complete. 1 New data copied to SPIDR. 5 SPTEF SPI Transmit Empty Interrupt Flag -- If set, this bit indicates that the transmit data register is empty. To clear this bit and place data into the transmit data register, SPISR must be read with SPTEF = 1, followed by a write to SPIDR. Any write to the SPI data register without reading SPTEF = 1, is effectively ignored. 0 SPI data register not empty. 1 SPI data register empty. 4 MODF Mode Fault Flag -- This bit is set if the SS input becomes low while the SPI is configured as a master and mode fault detection is enabled, MODFEN bit of SPICR2 register is set. Refer to MODFEN bit description in Section 12.3.2.2, "SPI Control Register 2 (SPICR2)". The flag is cleared automatically by a read of the SPI status register (with MODF set) followed by a write to the SPI control register 1. 0 Mode fault has not occurred. 1 Mode fault has occurred. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 525 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.3.2.5 R W Reset SPI Data Register (SPIDR) 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 2 Bit 0 0 0 0 0 0 0 0 0 Figure 12-7. SPI Data Register (SPIDR) Read: Anytime; normally read only when SPIF is set Write: Anytime The SPI data register is both the input and output register for SPI data. A write to this register allows a data byte to be queued and transmitted. For an SPI configured as a master, a queued data byte is transmitted immediately after the previous transmission has completed. The SPI transmitter empty flag SPTEF in the SPISR register indicates when the SPI data register is ready to accept new data. Received data in the SPIDR is valid when SPIF is set. If SPIF is cleared and a byte has been received, the received byte is transferred from the receive shift register to the SPIDR and SPIF is set. If SPIF is set and not serviced, and a second byte has been received, the second received byte is kept as valid byte in the receive shift register until the start of another transmission. The byte in the SPIDR does not change. If SPIF is set and a valid byte is in the receive shift register, and SPIF is serviced before the start of a third transmission, the byte in the receive shift register is transferred into the SPIDR and SPIF remains set (see Figure 12-8). If SPIF is set and a valid byte is in the receive shift register, and SPIF is serviced after the start of a third transmission, the byte in the receive shift register has become invalid and is not transferred into the SPIDR (see Figure 12-9). MC9S12XDP512 Data Sheet, Rev. 2.21 526 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) Data A Received Data B Received Data C Received SPIF Serviced Receive Shift Register Data B Data A Data C SPIF SPI Data Register Data B Data A = Unspecified Data C = Reception in progress Figure 12-8. Reception with SPIF Serviced in Time Data A Received Data B Received Data C Received Data B Lost SPIF Serviced Receive Shift Register Data B Data A Data C SPIF SPI Data Register Data A = Unspecified Data C = Reception in progress Figure 12-9. Reception with SPIF Serviced too Late MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 527 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4 Functional Description The SPI module allows a duplex, synchronous, serial communication between the MCU and peripheral devices. Software can poll the SPI status flags or SPI operation can be interrupt driven. The SPI system is enabled by setting the SPI enable (SPE) bit in SPI control register 1. While SPE is set, the four associated SPI port pins are dedicated to the SPI function as: * Slave select (SS) * Serial clock (SCK) * Master out/slave in (MOSI) * Master in/slave out (MISO) The main element of the SPI system is the SPI data register. The 8-bit data register in the master and the 8-bit data register in the slave are linked by the MOSI and MISO pins to form a distributed 16-bit register. When a data transfer operation is performed, this 16-bit register is serially shifted eight bit positions by the S-clock from the master, so data is exchanged between the master and the slave. Data written to the master SPI data register becomes the output data for the slave, and data read from the master SPI data register after a transfer operation is the input data from the slave. A read of SPISR with SPTEF = 1 followed by a write to SPIDR puts data into the transmit data register. When a transfer is complete and SPIF is cleared, received data is moved into the receive data register. This 8-bit data register acts as the SPI receive data register for reads and as the SPI transmit data register for writes. A single SPI register address is used for reading data from the read data buffer and for writing data to the transmit data register. The clock phase control bit (CPHA) and a clock polarity control bit (CPOL) in the SPI control register 1 (SPICR1) select one of four possible clock formats to be used by the SPI system. The CPOL bit simply selects a non-inverted or inverted clock. The CPHA bit is used to accommodate two fundamentally different protocols by sampling data on odd numbered SCK edges or on even numbered SCK edges (see Section 12.4.3, "Transmission Formats"). The SPI can be configured to operate as a master or as a slave. When the MSTR bit in SPI control register1 is set, master mode is selected, when the MSTR bit is clear, slave mode is selected. NOTE A change of CPOL or MSTR bit while there is a received byte pending in the receive shift register will destroy the received byte and must be avoided. MC9S12XDP512 Data Sheet, Rev. 2.21 528 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.1 Master Mode The SPI operates in master mode when the MSTR bit is set. Only a master SPI module can initiate transmissions. A transmission begins by writing to the master SPI data register. If the shift register is empty, the byte immediately transfers to the shift register. The byte begins shifting out on the MOSI pin under the control of the serial clock. * Serial clock The SPR2, SPR1, and SPR0 baud rate selection bits, in conjunction with the SPPR2, SPPR1, and SPPR0 baud rate preselection bits in the SPI baud rate register, control the baud rate generator and determine the speed of the transmission. The SCK pin is the SPI clock output. Through the SCK pin, the baud rate generator of the master controls the shift register of the slave peripheral. * MOSI, MISO pin In master mode, the function of the serial data output pin (MOSI) and the serial data input pin (MISO) is determined by the SPC0 and BIDIROE control bits. * SS pin If MODFEN and SSOE are set, the SS pin is configured as slave select output. The SS output becomes low during each transmission and is high when the SPI is in idle state. If MODFEN is set and SSOE is cleared, the SS pin is configured as input for detecting mode fault error. If the SS input becomes low this indicates a mode fault error where another master tries to drive the MOSI and SCK lines. In this case, the SPI immediately switches to slave mode, by clearing the MSTR bit and also disables the slave output buffer MISO (or SISO in bidirectional mode). So the result is that all outputs are disabled and SCK, MOSI, and MISO are inputs. If a transmission is in progress when the mode fault occurs, the transmission is aborted and the SPI is forced into idle state. This mode fault error also sets the mode fault (MODF) flag in the SPI status register (SPISR). If the SPI interrupt enable bit (SPIE) is set when the MODF flag becomes set, then an SPI interrupt sequence is also requested. When a write to the SPI data register in the master occurs, there is a half SCK-cycle delay. After the delay, SCK is started within the master. The rest of the transfer operation differs slightly, depending on the clock format specified by the SPI clock phase bit, CPHA, in SPI control register 1 (see Section 12.4.3, "Transmission Formats"). NOTE A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0, or BIDIROE with SPC0 set, SPPR2-SPPR0 and SPR2-SPR0 in master mode will abort a transmission in progress and force the SPI into idle state. The remote slave cannot detect this, therefore the master must ensure that the remote slave is returned to idle state. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 529 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.2 Slave Mode The SPI operates in slave mode when the MSTR bit in SPI control register 1 is clear. * Serial clock In slave mode, SCK is the SPI clock input from the master. * MISO, MOSI pin In slave mode, the function of the serial data output pin (MISO) and serial data input pin (MOSI) is determined by the SPC0 bit and BIDIROE bit in SPI control register 2. * SS pin The SS pin is the slave select input. Before a data transmission occurs, the SS pin of the slave SPI must be low. SS must remain low until the transmission is complete. If SS goes high, the SPI is forced into idle state. The SS input also controls the serial data output pin, if SS is high (not selected), the serial data output pin is high impedance, and, if SS is low, the first bit in the SPI data register is driven out of the serial data output pin. Also, if the slave is not selected (SS is high), then the SCK input is ignored and no internal shifting of the SPI shift register occurs. Although the SPI is capable of duplex operation, some SPI peripherals are capable of only receiving SPI data in a slave mode. For these simpler devices, there is no serial data out pin. NOTE When peripherals with duplex capability are used, take care not to simultaneously enable two receivers whose serial outputs drive the same system slave's serial data output line. As long as no more than one slave device drives the system slave's serial data output line, it is possible for several slaves to receive the same transmission from a master, although the master would not receive return information from all of the receiving slaves. If the CPHA bit in SPI control register 1 is clear, odd numbered edges on the SCK input cause the data at the serial data input pin to be latched. Even numbered edges cause the value previously latched from the serial data input pin to shift into the LSB or MSB of the SPI shift register, depending on the LSBFE bit. If the CPHA bit is set, even numbered edges on the SCK input cause the data at the serial data input pin to be latched. Odd numbered edges cause the value previously latched from the serial data input pin to shift into the LSB or MSB of the SPI shift register, depending on the LSBFE bit. When CPHA is set, the first edge is used to get the first data bit onto the serial data output pin. When CPHA is clear and the SS input is low (slave selected), the first bit of the SPI data is driven out of the serial data output pin. After the eighth shift, the transfer is considered complete and the received data is transferred into the SPI data register. To indicate transfer is complete, the SPIF flag in the SPI status register is set. NOTE A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0, or BIDIROE with SPC0 set in slave mode will corrupt a transmission in progress and must be avoided. MC9S12XDP512 Data Sheet, Rev. 2.21 530 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.3 Transmission Formats During an SPI transmission, data is transmitted (shifted out serially) and received (shifted in serially) simultaneously. The serial clock (SCK) synchronizes shifting and sampling of the information on the two serial data lines. A slave select line allows selection of an individual slave SPI device; slave devices that are not selected do not interfere with SPI bus activities. Optionally, on a master SPI device, the slave select line can be used to indicate multiple-master bus contention. MASTER SPI SHIFT REGISTER BAUD RATE GENERATOR SLAVE SPI MISO MISO MOSI MOSI SCK SCK SS VDD SHIFT REGISTER SS Figure 12-10. Master/Slave Transfer Block Diagram 12.4.3.1 Clock Phase and Polarity Controls Using two bits in the SPI control register 1, software selects one of four combinations of serial clock phase and polarity. The CPOL clock polarity control bit specifies an active high or low clock and has no significant effect on the transmission format. The CPHA clock phase control bit selects one of two fundamentally different transmission formats. Clock phase and polarity should be identical for the master SPI device and the communicating slave device. In some cases, the phase and polarity are changed between transmissions to allow a master device to communicate with peripheral slaves having different requirements. 12.4.3.2 CPHA = 0 Transfer Format The first edge on the SCK line is used to clock the first data bit of the slave into the master and the first data bit of the master into the slave. In some peripherals, the first bit of the slave's data is available at the slave's data out pin as soon as the slave is selected. In this format, the first SCK edge is issued a half cycle after SS has become low. A half SCK cycle later, the second edge appears on the SCK line. When this second edge occurs, the value previously latched from the serial data input pin is shifted into the LSB or MSB of the shift register, depending on LSBFE bit. After this second edge, the next bit of the SPI master data is transmitted out of the serial data output pin of the master to the serial input pin on the slave. This process continues for a total of 16 edges on the SCK line, with data being latched on odd numbered edges and shifted on even numbered edges. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 531 Chapter 12 Serial Peripheral Interface (S12SPIV4) Data reception is double buffered. Data is shifted serially into the SPI shift register during the transfer and is transferred to the parallel SPI data register after the last bit is shifted in. After the 16th (last) SCK edge: * Data that was previously in the master SPI data register should now be in the slave data register and the data that was in the slave data register should be in the master. * The SPIF flag in the SPI status register is set, indicating that the transfer is complete. Figure 12-11 is a timing diagram of an SPI transfer where CPHA = 0. SCK waveforms are shown for CPOL = 0 and CPOL = 1. The diagram may be interpreted as a master or slave timing diagram because the SCK, MISO, and MOSI pins are connected directly between the master and the slave. The MISO signal is the output from the slave and the MOSI signal is the output from the master. The SS pin of the master must be either high or reconfigured as a general-purpose output not affecting the SPI. End of Idle State Begin 1 SCK Edge Number 2 3 4 5 6 7 8 Begin of Idle State End Transfer 9 10 11 12 13 14 15 16 Bit 1 Bit 6 LSB Minimum 1/2 SCK for tT, tl, tL MSB SCK (CPOL = 0) SCK (CPOL = 1) If next transfer begins here SAMPLE I MOSI/MISO CHANGE O MOSI pin CHANGE O MISO pin SEL SS (O) Master only SEL SS (I) tT tL MSB first (LSBFE = 0): MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 LSB first (LSBFE = 1): LSB Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 tL = Minimum leading time before the first SCK edge tT = Minimum trailing time after the last SCK edge tI = Minimum idling time between transfers (minimum SS high time) tL, tT, and tI are guaranteed for the master mode and required for the slave mode. tI tL Figure 12-11. SPI Clock Format 0 (CPHA = 0) MC9S12XDP512 Data Sheet, Rev. 2.21 532 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) In slave mode, if the SS line is not deasserted between the successive transmissions then the content of the SPI data register is not transmitted; instead the last received byte is transmitted. If the SS line is deasserted for at least minimum idle time (half SCK cycle) between successive transmissions, then the content of the SPI data register is transmitted. In master mode, with slave select output enabled the SS line is always deasserted and reasserted between successive transfers for at least minimum idle time. 12.4.3.3 CPHA = 1 Transfer Format Some peripherals require the first SCK edge before the first data bit becomes available at the data out pin, the second edge clocks data into the system. In this format, the first SCK edge is issued by setting the CPHA bit at the beginning of the 8-cycle transfer operation. The first edge of SCK occurs immediately after the half SCK clock cycle synchronization delay. This first edge commands the slave to transfer its first data bit to the serial data input pin of the master. A half SCK cycle later, the second edge appears on the SCK pin. This is the latching edge for both the master and slave. When the third edge occurs, the value previously latched from the serial data input pin is shifted into the LSB or MSB of the SPI shift register, depending on LSBFE bit. After this edge, the next bit of the master data is coupled out of the serial data output pin of the master to the serial input pin on the slave. This process continues for a total of 16 edges on the SCK line with data being latched on even numbered edges and shifting taking place on odd numbered edges. Data reception is double buffered, data is serially shifted into the SPI shift register during the transfer and is transferred to the parallel SPI data register after the last bit is shifted in. After the 16th SCK edge: * Data that was previously in the SPI data register of the master is now in the data register of the slave, and data that was in the data register of the slave is in the master. * The SPIF flag bit in SPISR is set indicating that the transfer is complete. Figure 12-12 shows two clocking variations for CPHA = 1. The diagram may be interpreted as a master or slave timing diagram because the SCK, MISO, and MOSI pins are connected directly between the master and the slave. The MISO signal is the output from the slave, and the MOSI signal is the output from the master. The SS line is the slave select input to the slave. The SS pin of the master must be either high or reconfigured as a general-purpose output not affecting the SPI. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 533 Chapter 12 Serial Peripheral Interface (S12SPIV4) End of Idle State Begin SCK Edge Number 1 2 3 4 End Transfer 5 6 7 8 9 10 11 12 13 14 Begin of Idle State 15 16 SCK (CPOL = 0) SCK (CPOL = 1) If next transfer begins here SAMPLE I MOSI/MISO CHANGE O MOSI pin CHANGE O MISO pin SEL SS (O) Master only SEL SS (I) tT tL tI tL MSB first (LSBFE = 0): LSB first (LSBFE = 1): MSB Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 LSB Minimum 1/2 SCK for tT, tl, tL LSB Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 MSB tL = Minimum leading time before the first SCK edge, not required for back-to-back transfers tT = Minimum trailing time after the last SCK edge tI = Minimum idling time between transfers (minimum SS high time), not required for back-to-back transfers Figure 12-12. SPI Clock Format 1 (CPHA = 1) The SS line can remain active low between successive transfers (can be tied low at all times). This format is sometimes preferred in systems having a single fixed master and a single slave that drive the MISO data line. * Back-to-back transfers in master mode In master mode, if a transmission has completed and a new data byte is available in the SPI data register, this byte is sent out immediately without a trailing and minimum idle time. The SPI interrupt request flag (SPIF) is common to both the master and slave modes. SPIF gets set one half SCK cycle after the last SCK edge. MC9S12XDP512 Data Sheet, Rev. 2.21 534 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.4 SPI Baud Rate Generation Baud rate generation consists of a series of divider stages. Six bits in the SPI baud rate register (SPPR2, SPPR1, SPPR0, SPR2, SPR1, and SPR0) determine the divisor to the SPI module clock which results in the SPI baud rate. The SPI clock rate is determined by the product of the value in the baud rate preselection bits (SPPR2-SPPR0) and the value in the baud rate selection bits (SPR2-SPR0). The module clock divisor equation is shown in Equation 12-3. BaudRateDivisor = (SPPR + 1) * 2(SPR + 1) Eqn. 12-3 When all bits are clear (the default condition), the SPI module clock is divided by 2. When the selection bits (SPR2-SPR0) are 001 and the preselection bits (SPPR2-SPPR0) are 000, the module clock divisor becomes 4. When the selection bits are 010, the module clock divisor becomes 8, etc. When the preselection bits are 001, the divisor determined by the selection bits is multiplied by 2. When the preselection bits are 010, the divisor is multiplied by 3, etc. See Table 12-6 for baud rate calculations for all bit conditions, based on a 25 MHz bus clock. The two sets of selects allows the clock to be divided by a non-power of two to achieve other baud rates such as divide by 6, divide by 10, etc. The baud rate generator is activated only when the SPI is in master mode and a serial transfer is taking place. In the other cases, the divider is disabled to decrease IDD current. NOTE For maximum allowed baud rates, please refer to the SPI Electrical Specification in the Electricals chapter of this data sheet. 12.4.5 12.4.5.1 Special Features SS Output The SS output feature automatically drives the SS pin low during transmission to select external devices and drives it high during idle to deselect external devices. When SS output is selected, the SS output pin is connected to the SS input pin of the external device. The SS output is available only in master mode during normal SPI operation by asserting SSOE and MODFEN bit as shown in Table 12-2. The mode fault feature is disabled while SS output is enabled. NOTE Care must be taken when using the SS output feature in a multimaster system because the mode fault feature is not available for detecting system errors between masters. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 535 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.5.2 Bidirectional Mode (MOMI or SISO) The bidirectional mode is selected when the SPC0 bit is set in SPI control register 2 (see Table 12-8). In this mode, the SPI uses only one serial data pin for the interface with external device(s). The MSTR bit decides which pin to use. The MOSI pin becomes the serial data I/O (MOMI) pin for the master mode, and the MISO pin becomes serial data I/O (SISO) pin for the slave mode. The MISO pin in master mode and MOSI pin in slave mode are not used by the SPI. Table 12-8. Normal Mode and Bidirectional Mode When SPE = 1 Master Mode MSTR = 1 Serial Out Normal Mode SPC0 = 0 MOSI Serial In MOSI SPI SPI Serial In MISO Serial Out Bidirectional Mode SPC0 = 1 Slave Mode MSTR = 0 MOMI Serial Out MISO Serial In BIDIROE SPI Serial In BIDIROE SPI Serial Out SISO The direction of each serial I/O pin depends on the BIDIROE bit. If the pin is configured as an output, serial data from the shift register is driven out on the pin. The same pin is also the serial input to the shift register. * The SCK is output for the master mode and input for the slave mode. * The SS is the input or output for the master mode, and it is always the input for the slave mode. * The bidirectional mode does not affect SCK and SS functions. NOTE In bidirectional master mode, with mode fault enabled, both data pins MISO and MOSI can be occupied by the SPI, though MOSI is normally used for transmissions in bidirectional mode and MISO is not used by the SPI. If a mode fault occurs, the SPI is automatically switched to slave mode. In this case MISO becomes occupied by the SPI and MOSI is not used. This must be considered, if the MISO pin is used for another purpose. MC9S12XDP512 Data Sheet, Rev. 2.21 536 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.6 Error Conditions The SPI has one error condition: * Mode fault error 12.4.6.1 Mode Fault Error If the SS input becomes low while the SPI is configured as a master, it indicates a system error where more than one master may be trying to drive the MOSI and SCK lines simultaneously. This condition is not permitted in normal operation, the MODF bit in the SPI status register is set automatically, provided the MODFEN bit is set. In the special case where the SPI is in master mode and MODFEN bit is cleared, the SS pin is not used by the SPI. In this special case, the mode fault error function is inhibited and MODF remains cleared. In case the SPI system is configured as a slave, the SS pin is a dedicated input pin. Mode fault error doesn't occur in slave mode. If a mode fault error occurs, the SPI is switched to slave mode, with the exception that the slave output buffer is disabled. So SCK, MISO, and MOSI pins are forced to be high impedance inputs to avoid any possibility of conflict with another output driver. A transmission in progress is aborted and the SPI is forced into idle state. If the mode fault error occurs in the bidirectional mode for a SPI system configured in master mode, output enable of the MOMI (MOSI in bidirectional mode) is cleared if it was set. No mode fault error occurs in the bidirectional mode for SPI system configured in slave mode. The mode fault flag is cleared automatically by a read of the SPI status register (with MODF set) followed by a write to SPI control register 1. If the mode fault flag is cleared, the SPI becomes a normal master or slave again. NOTE If a mode fault error occurs and a received data byte is pending in the receive shift register, this data byte will be lost. 12.4.7 12.4.7.1 Low Power Mode Options SPI in Run Mode In run mode with the SPI system enable (SPE) bit in the SPI control register clear, the SPI system is in a low-power, disabled state. SPI registers remain accessible, but clocks to the core of this module are disabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 537 Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.7.2 SPI in Wait Mode SPI operation in wait mode depends upon the state of the SPISWAI bit in SPI control register 2. * If SPISWAI is clear, the SPI operates normally when the CPU is in wait mode * If SPISWAI is set, SPI clock generation ceases and the SPI module enters a power conservation state when the CPU is in wait mode. - If SPISWAI is set and the SPI is configured for master, any transmission and reception in progress stops at wait mode entry. The transmission and reception resumes when the SPI exits wait mode. - If SPISWAI is set and the SPI is configured as a slave, any transmission and reception in progress continues if the SCK continues to be driven from the master. This keeps the slave synchronized to the master and the SCK. If the master transmits several bytes while the slave is in wait mode, the slave will continue to send out bytes consistent with the operation mode at the start of wait mode (i.e., if the slave is currently sending its SPIDR to the master, it will continue to send the same byte. Else if the slave is currently sending the last received byte from the master, it will continue to send each previous master byte). NOTE Care must be taken when expecting data from a master while the slave is in wait or stop mode. Even though the shift register will continue to operate, the rest of the SPI is shut down (i.e., a SPIF interrupt will not be generated until exiting stop or wait mode). Also, the byte from the shift register will not be copied into the SPIDR register until after the slave SPI has exited wait or stop mode. In slave mode, a received byte pending in the receive shift register will be lost when entering wait or stop mode. An SPIF flag and SPIDR copy is generated only if wait mode is entered or exited during a tranmission. If the slave enters wait mode in idle mode and exits wait mode in idle mode, neither a SPIF nor a SPIDR copy will occur. 12.4.7.3 SPI in Stop Mode Stop mode is dependent on the system. The SPI enters stop mode when the module clock is disabled (held high or low). If the SPI is in master mode and exchanging data when the CPU enters stop mode, the transmission is frozen until the CPU exits stop mode. After stop, data to and from the external SPI is exchanged correctly. In slave mode, the SPI will stay synchronized with the master. The stop mode is not dependent on the SPISWAI bit. MC9S12XDP512 Data Sheet, Rev. 2.21 538 Freescale Semiconductor Chapter 12 Serial Peripheral Interface (S12SPIV4) 12.4.7.4 Reset The reset values of registers and signals are described in Section 12.3, "Memory Map and Register Definition", which details the registers and their bit fields. * If a data transmission occurs in slave mode after reset without a write to SPIDR, it will transmit garbage, or the byte last received from the master before the reset. * Reading from the SPIDR after reset will always read a byte of zeros. 12.4.7.5 Interrupts The SPI only originates interrupt requests when SPI is enabled (SPE bit in SPICR1 set). The following is a description of how the SPI makes a request and how the MCU should acknowledge that request. The interrupt vector offset and interrupt priority are chip dependent. The interrupt flags MODF, SPIF, and SPTEF are logically ORed to generate an interrupt request. 12.4.7.5.1 MODF MODF occurs when the master detects an error on the SS pin. The master SPI must be configured for the MODF feature (see Table 12-2). After MODF is set, the current transfer is aborted and the following bit is changed: * MSTR = 0, The master bit in SPICR1 resets. The MODF interrupt is reflected in the status register MODF flag. Clearing the flag will also clear the interrupt. This interrupt will stay active while the MODF flag is set. MODF has an automatic clearing process which is described in Section 12.3.2.4, "SPI Status Register (SPISR)". 12.4.7.5.2 SPIF SPIF occurs when new data has been received and copied to the SPI data register. After SPIF is set, it does not clear until it is serviced. SPIF has an automatic clearing process, which is described in Section 12.3.2.4, "SPI Status Register (SPISR)". 12.4.7.5.3 SPTEF SPTEF occurs when the SPI data register is ready to accept new data. After SPTEF is set, it does not clear until it is serviced. SPTEF has an automatic clearing process, which is described in Section 12.3.2.4, "SPI Status Register (SPISR)". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 539 Chapter 12 Serial Peripheral Interface (S12SPIV4) MC9S12XDP512 Data Sheet, Rev. 2.21 540 Freescale Semiconductor Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.1 Introduction The period interrupt timer (PIT) is an array of 24-bit timers that can be used to trigger peripheral modules or raise periodic interrupts. Refer to Figure 13-1 for a simplified block diagram. 13.1.1 Glossary Acronyms and Abbreviations PIT ISR CCR SoC micro time bases 13.1.2 Periodic Interrupt Timer Interrupt Service Routine Condition Code Register System on Chip clock periods of the 16-bit timer modulus down-counters, which are generated by the 8-bit modulus down-counters. Features The PIT includes these features: * Four timers implemented as modulus down-counters with independent time-out periods. * Time-out periods selectable between 1 and 224 bus clock cycles. Time-out equals m*n bus clock cycles with 1 <= m <= 256 and 1 <= n <= 65536. * Timers that can be enabled individually. * Four time-out interrupts. * Four time-out trigger output signals available to trigger peripheral modules. * Start of timer channels can be aligned to each other. 13.1.3 Modes of Operation Refer to the SoC guide for a detailed explanation of the chip modes. * Run mode This is the basic mode of operation. * Wait mode MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 541 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) PIT operation in wait mode is controlled by the PITSWAI bit located in the PITCFLMT register. In wait mode, if the bus clock is globally enabled and if the PITSWAI bit is clear, the PIT operates like in run mode. In wait mode, if the PITSWAI bit is set, the PIT module is stalled. Stop mode In full stop mode or pseudo stop mode, the PIT module is stalled. Freeze mode PIT operation in freeze mode is controlled by the PITFRZ bit located in the PITCFLMT register. In freeze mode, if the PITFRZ bit is clear, the PIT operates like in run mode. In freeze mode, if the PITFRZ bit is set, the PIT module is stalled. * * 13.1.4 Block Diagram Figure 13-1 shows a block diagram of the PIT. Bus Clock 8-Bit Micro Timer 0 Micro Time Base 0 16-Bit Timer 0 16-Bit Timer 1 8-Bit Micro Timer 1 Micro Time Base 1 16-Bit Timer 2 16-Bit Timer 3 Time-Out 0 Time-Out 1 Time-Out 2 Time-Out 3 Interrupt 0 Interface Trigger 0 Interrupt 1 Interface Trigger 1 Interrupt 2 Interface Trigger 2 Interrupt 3 Interface Trigger 3 Figure 13-1. PIT Block Diagram 13.2 External Signal Description The PIT module has no external pins. MC9S12XDP512 Data Sheet, Rev. 2.21 542 Freescale Semiconductor Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.3 Memory Map and Register Definition This section consists of register descriptions in address order. Each description includes a standard register diagram with an associated figure number. Details of register bit and field function follow the register diagrams, in bit order. Register Name PITCFLMT R W PITFLT Bit 7 6 5 PITE PITSWAI PITFRZ 0 0 0 R 4 3 2 1 Bit 0 0 0 0 0 0 PFLMT1 PFLMT0 0 W PITCE R PITMTLD1 W PITLD0 (High) R W PITLD0 (Low) R W PITCNT0 (High) R W PITCNT0 (Low) R W PITLD1 (High) R W PCE0 PMUX3 PMUX2 PMUX1 PMUX0 PINTE3 PINTE2 PINTE1 PINTE0 PTF3 PTF2 PTF1 PTF0 0 0 0 0 0 0 0 0 0 0 PMTLD7 PMTLD6 PMTLD5 PMTLD4 PMTLD3 PMTLD2 PMTLD1 PMTLD0 PMTLD7 PMTLD6 PMTLD5 PMTLD4 PMTLD3 PMTLD2 PMTLD1 PMTLD0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT15 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT7 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 R R PCE1 0 R W PCE2 0 R R PCE3 0 W PITMTLD0 0 PFLT0 0 W PITTF 0 PFLT1 0 W PITINTE 0 PFLT2 0 W PITMUX 0 PFLT3 = Unimplemented or Reserved Figure 13-2. PIT Register Summary (Sheet 1 of 2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 543 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) Register Name PITLD1 (Low) R W PITCNT1 (High) R W PITCNT1 (Low) R W PITLD2 (High) R W PITLD2 (Low) R W PITCNT2 (High) R W PITCNT2 (Low) R W PITLD3 (High) R W PITLD3 (Low) R W PITCNT3 (High) R W PITCNT3 (Low) R W Bit 7 6 5 4 3 2 1 Bit 0 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT15 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT7 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT15 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT7 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT15 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT7 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 = Unimplemented or Reserved Figure 13-2. PIT Register Summary (Sheet 2 of 2) MC9S12XDP512 Data Sheet, Rev. 2.21 544 Freescale Semiconductor Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.3.0.1 PIT Control and Force Load Micro Timer Register (PITCFLMT) 7 R W Reset 6 5 PITE PITSWAI PITFRZ 0 0 0 4 3 2 1 0 0 0 0 0 0 PFLMT1 PFLMT0 0 0 0 0 0 = Unimplemented or Reserved Figure 13-3. PIT Control and Force Load Micro Timer Register (PITCFLMT) Read: Anytime Write: Anytime; writes to the reserved bits have no effect Table 13-1. PITCFLMT Field Descriptions Field Description 7 PITE PIT Module Enable Bit -- This bit enables the PIT module. If PITE is cleared, the PIT module is disabled and flag bits in the PITTF register are cleared. When PITE is set, individually enabled timers (PCE set) start down-counting with the corresponding load register values. 0 PIT disabled (lower power consumption). 1 PIT is enabled. 6 PITSWAI PIT Stop in Wait Mode Bit -- This bit is used for power conservation while in wait mode. 0 PIT operates normally in wait mode 1 PIT clock generation stops and freezes the PIT module when in wait mode 5 PITFRZ PIT Counter Freeze while in Freeze Mode Bit -- When during debugging a breakpoint (freeze mode) is encountered it is useful in many cases to freeze the PIT counters to avoid e.g. interrupt generation. The PITFRZ bit controls the PIT operation while in freeze mode. 0 PIT operates normally in freeze mode 1 PIT counters are stalled when in freeze mode 1:0 PIT Force Load Bits for Micro Timer 1:0 -- These bits have only an effect if the corresponding micro timer is PFLMT[1:0] active and if the PIT module is enabled (PITE set). Writing a one into a PFLMT bit loads the corresponding 8-bit micro timer load register into the 8-bit micro timer down-counter. Writing a zero has no effect. Reading these bits will always return zero. Note: A micro timer force load affects all timer channels that use the corresponding micro time base. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 545 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.3.0.2 R PIT Force Load Timer Register (PITFLT) 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 PFLT3 PFLT2 PFLT1 PFLT0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 13-4. PIT Force Load Timer Register (PITFLT) Read: Anytime Write: Anytime; writes to the reserved bits have no effect Table 13-2. PITFLT Field Descriptions Field Description 3:0 PFLT[3:0] PIT Force Load Bits for Timer 3-0 -- These bits have only an effect if the corresponding timer channel (PCE set) is enabled and if the PIT module is enabled (PITE set). Writing a one into a PFLT bit loads the corresponding 16-bit timer load register into the 16-bit timer down-counter. Writing a zero has no effect. Reading these bits will always return zero. 13.3.0.3 R PIT Channel Enable Register (PITCE) 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 PCE3 PCE2 PCE1 PCE0 0 0 0 0 = Unimplemented or Reserved Figure 13-5. PIT Channel Enable Register (PITCE) Read: Anytime Write: Anytime; writes to the reserved bits have no effect Table 13-3. PITCE Field Descriptions Field Description 3:0 PCE[3:0] PIT Enable Bits for Timer Channel 3:0 -- These bits enable the PIT channels 3-0. If PCE is cleared, the PIT channel is disabled and the corresponding flag bit in the PITTF register is cleared. When PCE is set, and if the PIT module is enabled (PITE = 1) the 16-bit timer counter is loaded with the start count value and starts down-counting. 0 The corresponding PIT channel is disabled. 1 The corresponding PIT channel is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 546 Freescale Semiconductor Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.3.0.4 R PIT Multiplex Register (PITMUX) 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 PMUX3 PMUX2 PMUX1 PMUX0 0 0 0 0 = Unimplemented or Reserved Figure 13-6. PIT Multiplex Register (PITMUX) Read: Anytime Write: Anytime; writes to the reserved bits have no effect Table 13-4. PITMUX Field Descriptions Field Description 3:0 PMUX[3:0] PIT Multiplex Bits for Timer Channel 3:0 -- These bits select if the corresponding 16-bit timer is connected to micro time base 1 or 0. If PMUX is modified, the corresponding 16-bit timer is immediately switched to the other micro time base. 0 The corresponding 16-bit timer counts with micro time base 0. 1 The corresponding 16-bit timer counts with micro time base 1. 13.3.0.5 R PIT Interrupt Enable Register (PITINTE) 7 6 5 4 0 0 0 0 0 0 0 W Reset 0 3 2 1 0 PINTE3 PINTE2 PINTE1 PINTE0 0 0 0 0 = Unimplemented or Reserved Figure 13-7. PIT Interrupt Enable Register (PITINTE) Read: Anytime Write: Anytime; writes to the reserved bits have no effect Table 13-5. PITINTE Field Descriptions Field Description 3:0 PINTE[3:0] PIT Time-out Interrupt Enable Bits for Timer Channel 3:0 -- These bits enable an interrupt service request whenever the time-out flag PTF of the corresponding PIT channel is set. When an interrupt is pending (PTF set) enabling the interrupt will immediately cause an interrupt. To avoid this, the corresponding PTF flag has to be cleared first. 0 Interrupt of the corresponding PIT channel is disabled. 1 Interrupt of the corresponding PIT channel is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 547 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.3.0.6 R PIT Time-Out Flag Register (PITTF) 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 PTF3 PTF2 PTF1 PTF0 0 0 0 0 = Unimplemented or Reserved Figure 13-8. PIT Time-Out Flag Register (PITTF) Read: Anytime Write: Anytime (write to clear); writes to the reserved bits have no effect Table 13-6. PITTF Field Descriptions Field Description 3:0 PTF[3:0] PIT Time-out Flag Bits for Timer Channel 3:0 -- PTF is set when the corresponding 16-bit timer modulus down-counter and the selected 8-bit micro timer modulus down-counter have counted to zero. The flag can be cleared by writing a one to the flag bit. Writing a zero has no effect. If flag clearing by writing a one and flag setting happen in the same bus clock cycle, the flag remains set. The flag bits are cleared if the PIT module is disabled or if the corresponding timer channel is disabled. 0 Time-out of the corresponding PIT channel has not yet occurred. 1 Time-out of the corresponding PIT channel has occurred. 13.3.0.7 R W Reset PIT Micro Timer Load Register 0 to 1 (PITMTLD0-1) 7 6 5 4 3 2 1 0 PMTLD7 PMTLD6 PMTLD5 PMTLD4 PMTLD3 PMTLD2 PMTLD1 PMTLD0 0 0 0 0 0 0 0 0 Figure 13-9. PIT Micro Timer Load Register 0 (PITMTLD0) R W Reset 7 6 5 4 3 2 1 0 PMTLD7 PMTLD6 PMTLD5 PMTLD4 PMTLD3 PMTLD2 PMTLD1 PMTLD0 0 0 0 0 0 0 0 0 Figure 13-10. PIT Micro Timer Load Register 1 (PITMTLD1) Read: Anytime Write: Anytime Table 13-7. PITMTLD0-1 Field Descriptions Field Description 7:0 PIT Micro Timer Load Bits 7:0 -- These bits set the 8-bit modulus down-counter load value of the micro timers. PMTLD[7:0] Writing a new value into the PITMTLD register will not restart the timer. When the micro timer has counted down to zero, the PMTLD register value will be loaded. The PFLMT bits in the PITCFLMT register can be used to immediately update the count register with the new value if an immediate load is desired. MC9S12XDP512 Data Sheet, Rev. 2.21 548 Freescale Semiconductor Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.3.0.8 PIT Load Register 0 to 3 (PITLD0-3) 15 R W 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4 3 2 1 0 Figure 13-11. PIT Load Register 0 (PITLD0) 15 R W 14 13 12 11 10 9 8 7 6 5 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4 3 2 1 0 Figure 13-12. PIT Load Register 1 (PITLD1) 15 R W 14 13 12 11 10 9 8 7 6 5 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4 3 2 1 0 Figure 13-13. PIT Load Register 2 (PITLD2) 15 R W 14 13 12 11 10 9 8 7 6 5 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 13-14. PIT Load Register 3 (PITLD3) Read: Anytime Write: Anytime Table 13-8. PITLD0-3 Field Descriptions Field Description 15:0 PLD[15:0] PIT Load Bits 15:0 -- These bits set the 16-bit modulus down-counter load value. Writing a new value into the PITLD register must be a 16-bit access, to ensure data consistency. It will not restart the timer. When the timer has counted down to zero the PTF time-out flag will be set and the register value will be loaded. The PFLT bits in the PITFLT register can be used to immediately update the count register with the new value if an immediate load is desired. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 549 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.3.0.9 PIT Count Register 0 to 3 (PITCNT0-3) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 R PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 W 15 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4 3 2 1 0 Figure 13-15. PIT Count Register 0 (PITCNT0) 15 14 13 12 11 10 9 8 7 6 5 R PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 W 15 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4 3 2 1 0 Figure 13-16. PIT Count Register 1 (PITCNT1) 15 14 13 12 11 10 9 8 7 6 5 R PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 W 15 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 4 3 2 1 0 Figure 13-17. PIT Count Register 2 (PITCNT2) 15 14 13 12 11 10 9 8 7 6 5 R PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT PCNT 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 W 15 Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Figure 13-18. PIT Count Register 3 (PITCNT3) Read: Anytime Write: Has no meaning or effect Table 13-9. PITCNT0-3 Field Descriptions Field Description 15:0 PIT Count Bits 15-0 -- These bits represent the current 16-bit modulus down-counter value. The read access PCNT[15:0] for the count register must take place in one clock cycle as a 16-bit access. MC9S12XDP512 Data Sheet, Rev. 2.21 550 Freescale Semiconductor Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) 13.4 Functional Description Figure 13-19 shows a detailed block diagram of the PIT module. The main parts of the PIT are status, control and data registers, two 8-bit down-counters, four 16-bit down-counters and an interrupt/trigger interface. 4 PMUX0 4 PITMUX Register time-out 0 PFLT1 [1] 8-Bit Micro Timer 0 [0] Timer 1 PITLD1 Register PITCNT1 Register PMUX Clock Timer 0 PITLD0 Register PITCNT0 Register PITMLD0 Register Bus PIT_24B4C PFLT0 PITFLT Register timeout 1 [2] 8-Bit Micro Timer 1 [1] Timer 2 PITLD2 Register PITCNT2 Register PITCFLMT Register 4 Hardware Trigger PFLT2 PITMLD1 Register Interrupt / Trigger Interface PITTF Register 4 timeout 2 PITINTE Register Interrupt Request PFLT3 PFLMT PMUX3 Timer 3 PITLD3 Register PITCNT3 Register Time-Out 3 Figure 13-19. PIT Detailed Block Diagram 13.4.1 Timer As shown in Figure 13-1and Figure 13-19, the 24-bit timers are built in a two-stage architecture with four 16-bit modulus down-counters and two 8-bit modulus down-counters. The 16-bit timers are clocked with two selectable micro time bases which are generated with 8-bit modulus down-counters. Each 16-bit timer is connected to micro time base 0 or 1 via the PMUX[3:0] bit setting in the PIT Multiplex (PITMUX) register. A timer channel is enabled if the module enable bit PITE in the PIT control and force load micro timer (PITCFLMT) register is set and if the corresponding PCE bit in the PIT channel enable (PITCE) register is set. Two 8-bit modulus down-counters are used to generate two micro time bases. As soon as a micro time base is selected for an enabled timer channel, the corresponding micro timer modulus down-counter will load its start value as specified in the PITMTLD0 or PITMTLD1 register and will start down-counting. Whenever the micro timer down-counter has counted to zero the PITMTLD register is reloaded and the connected 16-bit modulus down-counters count one cycle. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 551 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) Whenever a 16-bit timer counter and the connected 8-bit micro timer counter have counted to zero, the PITLD register is reloaded and the corresponding time-out flag PTF in the PIT time-out flag (PITTF) register is set, as shown in Figure 13-20. The time-out period is a function of the timer load (PITLD) and micro timer load (PITMTLD) registers and the bus clock fBUS: time-out period = (PITMTLD + 1) * (PITLD + 1) / fBUS. For example, for a 40 MHz bus clock, the maximum time-out period equals: 256 * 65536 * 25 ns = 419.43 ms. The current 16-bit modulus down-counter value can be read via the PITCNT register. The micro timer down-counter values cannot be read. The 8-bit micro timers can individually be restarted by writing a one to the corresponding force load micro timer PFLMT bits in the PIT control and force load micro timer (PITCFLMT) register. The 16-bit timers can individually be restarted by writing a one to the corresponding force load timer PFLT bits in the PIT forceload timer (PITFLT) register. If desired, any group of timers and micro timers can be restarted at the same time by using one 16-bit write to the adjacent PITCFLMT and PITFLT registers with the relevant bits set, as shown in Figure 13-20. Bus Clock 8-Bit Micro Timer Counter PITCNT Register 0 00 2 1 0 2 0001 1 0 2 0000 1 0001 0 2 1 1 2 0000 0 0001 2 1 0 0000 2 1 0 2 0001 8-Bit Force Load 16-Bit Force Load PTF Flag1 PITTRIG Time-Out Period Note 1. The PTF flag clearing depends on the software Time-Out Period After Restart Figure 13-20. PIT Trigger and Flag Signal Timing 13.4.2 Interrupt Interface Each time-out event can be used to trigger an interrupt service request. For each timer channel, an individual bit PINTE in the PIT interrupt enable (PITINTE) register exists to enable this feature. If PINTE MC9S12XDP512 Data Sheet, Rev. 2.21 552 Freescale Semiconductor Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) is set, an interrupt service is requested whenever the corresponding time-out flag PTF in the PIT time-out flag (PITTF) register is set. The flag can be cleared by writing a one to the flag bit. NOTE Be careful when resetting the PITE, PINTE or PITCE bits in case of pending PIT interrupt requests, to avoid spurious interrupt requests. 13.4.3 Hardware Trigger The PIT module contains four hardware trigger signal lines PITTRIG[3:0], one for each timer channel. These signals can be connected on SoC level to peripheral modules enabling e.g. periodic ATD conversion (please refer to the SoC Guide for the mapping of PITTRIG[3:0] signals to peripheral modules). Whenever a timer channel time-out is reached, the corresponding PTF flag is set and the corresponding trigger signal PITTRIG triggers a rising edge. The trigger feature requires a minimum time-out period of two bus clock cycles because the trigger is asserted high for at least one bus clock cycle. For load register values PITLD = 0x0001 and PITMTLD = 0x0002 the flag setting, trigger timing and a restart with force load is shown in Figure 13-20. 13.5 13.5.1 Initialization/Application Information Startup Set the configuration registers before the PITE bit in the PITCFLMT register is set. Before PITE is set, the configuration registers can be written in arbitrary order. 13.5.2 Shutdown When the PITCE register bits, the PITINTE register bits or the PITE bit in the PITCFLMT register are cleared, the corresponding PIT interrupt flags are cleared. In case of a pending PIT interrupt request, a spurious interrupt can be generated. Two strategies, which avoid spurious interrupts, are recommended: 1. Reset the PIT interrupt flags only in an ISR. When entering the ISR, the I mask bit in the CCR is set automatically. The I mask bit must not be cleared before the PIT interrupt flags are cleared. 2. After setting the I mask bit with the SEI instruction, the PIT interrupt flags can be cleared. Then clear the I mask bit with the CLI instruction to re-enable interrupts. 13.5.3 Flag Clearing A flag is cleared by writing a one to the flag bit. Always use store or move instructions to write a one in certain bit positions. Do not use the BSET instructions. Do not use any C-constructs that compile to BSET instructions. "BSET flag_register, #mask" must not be used for flag clearing because BSET is a read-modify-write instruction which writes back the "bit-wise or" of the flag_register and the mask into the flag_register. BSET would clear all flag bits that were set, independent from the mask. For example, to clear flag bit 0 use: MOVB #$01,PITTF. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 553 Chapter 13 Periodic Interrupt Timer (S12PIT24B4CV1) MC9S12XDP512 Data Sheet, Rev. 2.21 554 Freescale Semiconductor Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.1 Introduction Module VREG_3V3 is a dual output voltage regulator that provides two separate 2.5V (typical) supplies differing in the amount of current that can be sourced. The regulator input voltage range is from 3.3V up to 5V (typical). 14.1.1 Features Module VREG_3V3 includes these distinctive features: * Two parallel, linear voltage regulators -- Bandgap reference * Low-voltage detect (LVD) with low-voltage interrupt (LVI) * Power-on reset (POR) * Low-voltage reset (LVR) * Autonomous periodical interrupt (API) 14.1.2 Modes of Operation There are three modes VREG_3V3 can operate in: 1. Full performance mode (FPM) (MCU is not in stop mode) The regulator is active, providing the nominal supply voltage of 2.5 V with full current sourcing capability at both outputs. Features LVD (low-voltage detect), LVR (low-voltage reset), and POR (power-on reset) are available. The API is available. 2. Reduced power mode (RPM) (MCU is in stop mode) The purpose is to reduce power consumption of the device. The output voltage may degrade to a lower value than in full performance mode, additionally the current sourcing capability is substantially reduced. Only the POR is available in this mode, LVD and LVR are disabled. The API is available. 3. Shutdown mode Controlled by VREGEN (see device level specification for connectivity of VREGEN). This mode is characterized by minimum power consumption. The regulator outputs are in a high-impedance state, only the POR feature is available, LVD and LVR are disabled. The API internal RC oscillator clock is not available. This mode must be used to disable the chip internal regulator VREG_3V3, i.e., to bypass the VREG_3V3 to use external supplies. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 555 Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.1.3 Block Diagram Figure 14-1 shows the function principle of VREG_3V3 by means of a block diagram. The regulator core REG consists of two parallel subblocks, REG1 and REG2, providing two independent output voltages. VDDPLL REG2 VDDR REG VSSPLL VDDA VBG VDD REG1 LVD LVR LVR POR POR VSS VSSA VREGEN CTRL LVI API Rate Select API API Bus Clock LVD: Low-Voltage Detect REG: Regulator Core LVR: Low-Voltage Reset CTRL: Regulator Control POR: Power-On Reset API: Auto. Periodical Interrupt PIN Figure 14-1. VREG_3V3 Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 556 Freescale Semiconductor Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.2 External Signal Description Due to the nature of VREG_3V3 being a voltage regulator providing the chip internal power supply voltages, most signals are power supply signals connected to pads. Table 14-1 shows all signals of VREG_3V3 associated with pins. Table 14-1. Signal Properties Name Function Reset State Pull Up -- -- VDDR Power input (positive supply) VDDA Quiet input (positive supply) -- -- VSSA Quiet input (ground) -- -- VDD Primary output (positive supply) -- -- VSS Primary output (ground) -- -- VDDPLL Secondary output (positive supply) -- -- VSSPLL Secondary output (ground) -- -- VREGEN (optional) Optional Regulator Enable -- -- NOTE Check device level specification for connectivity of the signals. 14.2.1 VDDR -- Regulator Power Input Pins Signal VDDR is the power input of VREG_3V3. All currents sourced into the regulator loads flow through this pin. A chip external decoupling capacitor (>=100 nF, X7R ceramic) between VDDR and VSSR (if VSSR is not available VSS) can smooth ripple on VDDR. For entering Shutdown Mode, pin VDDR should also be tied to ground on devices without VREGEN pin. 14.2.2 VDDA, VSSA -- Regulator Reference Supply Pins Signals VDDA/VSSA, which are supposed to be relatively quiet, are used to supply the analog parts of the regulator. Internal precision reference circuits are supplied from these signals. A chip external decoupling capacitor (>=100 nF, X7R ceramic) between VDDA and VSSA can further improve the quality of this supply. 14.2.3 VDD, VSS -- Regulator Output1 (Core Logic) Pins Signals VDD/VSS are the primary outputs of VREG_3V3 that provide the power supply for the core logic. These signals are connected to device pins to allow external decoupling capacitors (220 nF, X7R ceramic). In Shutdown Mode an external supply driving VDD/VSS can replace the voltage regulator. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 557 Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.2.4 VDDPLL, VSSPLL -- Regulator Output2 (PLL) Pins Signals VDDPLL/VSSPLL are the secondary outputs of VREG_3V3 that provide the power supply for the PLL and oscillator. These signals are connected to device pins to allow external decoupling capacitors (220 nF, X7R ceramic). In Shutdown Mode, an external supply driving VDDPLL/VSSPLL can replace the voltage regulator. 14.2.5 VREGEN -- Optional Regulator Enable Pin This optional signal is used to shutdown VREG_3V3. In that case, VDD/VSS and VDDPLL/VSSPLL must be provided externally. Shutdown mode is entered with VREGEN being low. If VREGEN is high, the VREG_3V3 is either in Full Performance Mode or in Reduced Power Mode. For the connectivity of VREGEN, see device specification. NOTE Switching from FPM or RPM to shutdown of VREG_3V3 and vice versa is not supported while MCU is powered. 14.3 Memory Map and Register Definition This section provides a detailed description of all registers accessible in VREG_3V3. If enabled in the system, the VREG_3V3 will abort all read and write accesses to reserved registers within it's memory slice. 14.3.1 Module Memory Map Table 14-2 provides an overview of all used registers. Table 14-2. Memory Map Address Offset Use Access 0x0000 HT Control Register (VREGHTCL) -- 0x0001 Control Register (VREGCTRL) R/W 0x0002 Autonomous Periodical Interrupt Control Register (VREGAPICL) R/W 0x0003 Autonomous Periodical Interrupt Trimming Register (VREGAPITR) R/W 0x0004 Autonomous Periodical Interrupt Period High (VREGAPIRH) R/W 0x0005 Autonomous Periodical Interrupt Period Low (VREGAPIRL) R/W 0x0006 Reserved 06 -- 0x0007 Reserved 07 -- MC9S12XDP512 Data Sheet, Rev. 2.21 558 Freescale Semiconductor Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.3.2 Register Descriptions This section describes all the VREG_3V3 registers and their individual bits. 14.3.2.1 HT Control Register (VREGHTCL) The VREGHTCL is reserved for test purposes. This register should not be written. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 14-2. HT Control Register (VREGHTCL) 14.3.2.2 Control Register (VREGCTRL) The VREGCTRL register allows the configuration of the VREG_3V3 low-voltage detect features. R 7 6 5 4 3 2 0 0 0 0 0 LVDS 0 0 0 0 0 0 W Reset 1 0 LVIE LVIF 0 0 = Unimplemented or Reserved Figure 14-3. Control Register (VREGCTRL) Table 14-3. VREGCTRL Field Descriptions Field Description 2 LVDS Low-Voltage Detect Status Bit -- This read-only status bit reflects the input voltage. Writes have no effect. 0 Input voltage VDDA is above level VLVID or RPM or shutdown mode. 1 Input voltage VDDA is below level VLVIA and FPM. 1 LVIE Low-Voltage Interrupt Enable Bit 0 Interrupt request is disabled. 1 Interrupt will be requested whenever LVIF is set. 0 LVIF Low-Voltage Interrupt Flag -- LVIF is set to 1 when LVDS status bit changes. This flag can only be cleared by writing a 1. Writing a 0 has no effect. If enabled (LVIE = 1), LVIF causes an interrupt request. 0 No change in LVDS bit. 1 LVDS bit has changed. Note: On entering the Reduced Power Mode the LVIF is not cleared by the VREG_3V3. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 559 Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.3.2.3 Autonomous Periodical Interrupt Control Register (VREGAPICL) The VREGAPICL register allows the configuration of the VREG_3V3 autonomous periodical interrupt features. 7 R W Reset APICLK 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 APIFE APIE APIF 0 0 0 = Unimplemented or Reserved Figure 14-4. Autonomous Periodical Interrupt Control Register (VREGAPICL) Table 14-4. VREGAPICL Field Descriptions Field Description 7 APICLK Autonomous Periodical Interrupt Clock Select Bit -- Selects the clock source for the API. Writable only if APIFE = 0; APICLK cannot be changed if APIFE is set by the same write operation. 0 Autonomous periodical interrupt clock used as source. 1 Bus clock used as source. 2 APIFE Autonomous Periodical Interrupt Feature Enable Bit -- Enables the API feature and starts the API timer when set. 0 Autonomous periodical interrupt is disabled. 1 Autonomous periodical interrupt is enabled and timer starts running. 1 APIE Autonomous Periodical Interrupt Enable Bit 0 API interrupt request is disabled. 1 API interrupt will be requested whenever APIF is set. 0 APIF Autonomous Periodical Interrupt Flag -- APIF is set to 1 when the in the API configured time has elapsed. This flag can only be cleared by writing a 1 to it. Clearing of the flag has precedence over setting. Writing a 0 has no effect. If enabled (APIE = 1), APIF causes an interrupt request. 0 API timeout has not yet occurred. 1 API timeout has occurred. MC9S12XDP512 Data Sheet, Rev. 2.21 560 Freescale Semiconductor Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.3.2.4 Autonomous Periodical Interrupt Trimming Register (VREGAPITR) The VREGAPITR register allows to trim the API timeout period. 7 R W Reset 6 5 4 3 2 APITR5 APITR4 APITR3 APITR2 APITR1 APITR0 01 01 01 01 01 01 1 0 0 0 0 0 1. Reset value is either 0 or preset by factory. See Device User Guide for details. = Unimplemented or Reserved Figure 14-5. Autonomous Periodical Interrupt Trimming Register (VREGAPITR) Table 14-5. VREGAPITR Field Descriptions Field 7-2 APITR[5:0] Description Autonomous Periodical Interrupt Period Trimming Bits -- See Table 14-6 for trimming effects. Table 14-6. Trimming Effect of APIT Bit Trimming Effect APITR[5] Increases period APITR[4] Decreases period less than APITR[5] increased it APITR[3] Decreases period less than APITR[4] APITR[2] Decreases period less than APITR[3] APITR[1] Decreases period less than APITR[2] APITR[0] Decreases period less than APITR[1] MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 561 Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.3.2.5 Autonomous Periodical Interrupt Rate High and Low Register (VREGAPIRH / VREGAPIRL) The VREGAPIRH and VREGAPIRL register allows the configuration of the VREG_3V3 autonomous periodical interrupt rate. R 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 APIR11 APIR10 APIR9 APIR8 0 0 0 0 = Unimplemented or Reserved Figure 14-6. Autonomous Periodical Interrupt Rate High Register (VREGAPIRH) R W Reset 7 6 5 4 3 2 1 0 APIR7 APIR6 APIR5 APIR4 APIR3 APIR2 APIR1 APIR0 0 0 0 0 0 0 0 0 Figure 14-7. Autonomous Periodical Interrupt Rate Low Register (VREGAPIRL) Table 14-7. VREGAPIRH / VREGAPIRL Field Descriptions Field Description 11-0 APIR[11:0] Autonomous Periodical Interrupt Rate Bits -- These bits define the timeout period of the API. See Table 14-8 for details of the effect of the autonomous periodical interrupt rate bits. Writable only if APIFE = 0 of VREGAPICL register. MC9S12XDP512 Data Sheet, Rev. 2.21 562 Freescale Semiconductor Chapter 14 Voltage Regulator (S12VREG3V3V5) Table 14-8. Selectable Autonomous Periodical Interrupt Periods 1 APICLK APIR[11:0] Selected Period 0 000 0.2 ms1 0 001 0.4 ms1 0 002 0.6 ms1 0 003 0.8 ms1 0 004 1.0 ms1 0 005 1.2 ms1 0 ..... ..... 0 FFD 818.8 ms1 0 FFE 819 ms1 0 FFF 819.2 ms1 1 000 2 * bus clock period 1 001 4 * bus clock period 1 002 6 * bus clock period 1 003 8 * bus clock period 1 004 10 * bus clock period 1 005 12 * bus clock period 1 ..... ..... 1 FFD 8188 * bus clock period 1 FFE 8190 * bus clock period 1 FFF 8192 * bus clock period When trimmed within specified accuracy. See electrical specifications for details. You can calculate the selected period depending of APICLK as: Period = 2*(APIR[11:0] + 1) * 0.1 ms or period = 2*(APIR[11:0] + 1) * bus clock period MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 563 Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.3.2.6 Reserved 06 The Reserved 06 is reserved for test purposes. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 14-8. Reserved 06 14.3.2.7 Reserved 07 The Reserved 07 is reserved for test purposes. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 14-9. Reserved 07 14.4 Functional Description 14.4.1 General Module VREG_3V3 is a voltage regulator, as depicted in Figure 14-1. The regulator functional elements are the regulator core (REG), a low-voltage detect module (LVD), a control block (CTRL), a power-on reset module (POR), and a low-voltage reset module (LVR). 14.4.2 Regulator Core (REG) Respectively its regulator core has two parallel, independent regulation loops (REG1 and REG2) that differ only in the amount of current that can be delivered. The regulator is a linear regulator with a bandgap reference when operated in Full Performance Mode. It acts as a voltage clamp in Reduced Power Mode. All load currents flow from input VDDR to VSS or VSSPLL. The reference circuits are supplied by VDDA and VSSA. 14.4.2.1 Full Performance Mode In Full Performance Mode, the output voltage is compared with a reference voltage by an operational amplifier. The amplified input voltage difference drives the gate of an output transistor. MC9S12XDP512 Data Sheet, Rev. 2.21 564 Freescale Semiconductor Chapter 14 Voltage Regulator (S12VREG3V3V5) 14.4.2.2 Reduced Power Mode In Reduced Power Mode, the gate of the output transistor is connected directly to a reference voltage to reduce power consumption. 14.4.3 Low-Voltage Detect (LVD) Subblock LVD is responsible for generating the low-voltage interrupt (LVI). LVD monitors the input voltage (VDDA-VSSA) and continuously updates the status flag LVDS. Interrupt flag LVIF is set whenever status flag LVDS changes its value. The LVD is available in FPM and is inactive in Reduced Power Mode or Shutdown Mode. 14.4.4 Power-On Reset (POR) This functional block monitors VDD. If VDD is below VPORD, POR is asserted; if VDD exceeds VPORD, the POR is deasserted. POR asserted forces the MCU into Reset. POR Deasserted will trigger the power-on sequence. 14.4.5 Low-Voltage Reset (LVR) Block LVR monitors the primary output voltage VDD. If it drops below the assertion level (VLVRA) signal, LVR asserts; if VDD rises above the deassertion level (VLVRD) signal, LVR deasserts. The LVR function is available only in Full Performance Mode. 14.4.6 Regulator Control (CTRL) This part contains the register block of VREG_3V3 and further digital functionality needed to control the operating modes. CTRL also represents the interface to the digital core logic. 14.4.7 Autonomous Periodical Interrupt (API) Subblock API can generate periodical interrupts independent of the clock source of the MCU. To enable the timer, the bit APIFE needs to be set. The API timer is either clocked by a trimmable internal RC oscillator or the bus clock. Timer operation will freeze when MCU clock source is selected and bus clock is turned off. See CRG specification for details. The clock source can be selected with bit APICLK. APICLK can only be written when APIFE is not set. The APIR[11:0] bits determine the interrupt period. APIR[11:0] can only be written when APIFE is cleared. As soon as APIFE is set, the timer starts running for the period selected by APIR[11:0] bits. When the configured time has elapsed, the flag APIF is set. An interrupt, indicated by flag APIF = 1, is triggered if interrupt enable bit APIE = 1. The timer is started automatically again after it has set APIF. The procedure to change APICLK or APIR[11:0] is first to clear APIFE, then write to APICLK or APIR[11:0], and afterwards set APIFE. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 565 Chapter 14 Voltage Regulator (S12VREG3V3V5) The API Trimming bits APITR[5:0] must be set so the minimum period equals 0.2 ms if stable frequency is desired. See Table 14-6 for the trimming effect of APITR. NOTE The first period after enabling the counter by APIFE might be reduced. The API internal RC oscillator clock is not available if VREG_3V3 is in Shutdown Mode. 14.4.8 Resets This section describes how VREG_3V3 controls the reset of the MCU.The reset values of registers and signals are provided in Section 14.3, "Memory Map and Register Definition". Possible reset sources are listed in Table 14-9. Table 14-9. Reset Sources 14.4.9 14.4.9.1 Reset Source Local Enable Power-on reset Always active Low-voltage reset Available only in Full Performance Mode Description of Reset Operation Power-On Reset (POR) During chip power-up the digital core may not work if its supply voltage VDD is below the POR deassertion level (VPORD). Therefore, signal POR, which forces the other blocks of the device into reset, is kept high until VDD exceeds VPORD. The MCU will run the start-up sequence after POR deassertion. The power-on reset is active in all operation modes of VREG_3V3. 14.4.9.2 Low-Voltage Reset (LVR) For details on low-voltage reset, see Section 14.4.5, "Low-Voltage Reset (LVR)". 14.4.10 Interrupts This section describes all interrupts originated by VREG_3V3. The interrupt vectors requested by VREG_3V3 are listed in Table 14-10. Vector addresses and interrupt priorities are defined at MCU level. Table 14-10. Interrupt Vectors Interrupt Source Local Enable Low-voltage interrupt (LVI) LVIE = 1; available only in Full Performance Mode MC9S12XDP512 Data Sheet, Rev. 2.21 566 Freescale Semiconductor Chapter 14 Voltage Regulator (S12VREG3V3V5) Table 14-10. Interrupt Vectors Interrupt Source Local Enable Autonomous periodical interrupt (API) APIE = 1 14.4.10.1 Low-Voltage Interrupt (LVI) In FPM, VREG_3V3 monitors the input voltage VDDA. Whenever VDDA drops below level VLVIA, the status bit LVDS is set to 1. On the other hand, LVDS is reset to 0 when VDDA rises above level VLVID. An interrupt, indicated by flag LVIF = 1, is triggered by any change of the status bit LVDS if interrupt enable bit LVIE = 1. NOTE On entering the Reduced Power Mode, the LVIF is not cleared by the VREG_3V3. 14.4.10.2 Autonomous Periodical Interrupt (API) As soon as the configured timeout period of the API has elapsed, the APIF bit is set. An interrupt, indicated by flag APIF = 1, is triggered if interrupt enable bit APIE = 1. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 567 Chapter 14 Voltage Regulator (S12VREG3V3V5) MC9S12XDP512 Data Sheet, Rev. 2.21 568 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) 15.1 Introduction This section describes the functionality of the background debug module (BDM) sub-block of the HCS12X core platform. The background debug module (BDM) sub-block is a single-wire, background debug system implemented in on-chip hardware for minimal CPU intervention. All interfacing with the BDM is done via the BKGD pin. The BDM has enhanced capability for maintaining synchronization between the target and host while allowing more flexibility in clock rates. This includes a sync signal to determine the communication rate and a handshake signal to indicate when an operation is complete. The system is backwards compatible to the BDM of the S12 family with the following exceptions: * TAGGO command no longer supported by BDM * External instruction tagging feature now part of DBG module * BDM register map and register content extended/modified * Global page access functionality * Enabled but not active out of reset in emulation modes * CLKSW bit set out of reset in emulation mode. * Family ID readable from firmware ROM at global address 0x7FFF0F (value for HCS12X devices is 0xC1) 15.1.1 Features The BDM includes these distinctive features: * Single-wire communication with host development system * Enhanced capability for allowing more flexibility in clock rates * SYNC command to determine communication rate * GO_UNTIL command * Hardware handshake protocol to increase the performance of the serial communication * Active out of reset in special single chip mode * Nine hardware commands using free cycles, if available, for minimal CPU intervention * Hardware commands not requiring active BDM * 14 firmware commands execute from the standard BDM firmware lookup table MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 569 Chapter 15 Background Debug Module (S12XBDMV2) * * * * * * * * Software control of BDM operation during wait mode Software selectable clocks Global page access functionality Enabled but not active out of reset in emulation modes CLKSW bit set out of reset in emulation mode. When secured, hardware commands are allowed to access the register space in special single chip mode, if the Flash and EEPROM erase tests fail. Family ID readable from firmware ROM at global address 0x7FFF0F (value for HCS12X devices is 0xC1) BDM hardware commands are operational until system stop mode is entered (all bus masters are in stop mode) 15.1.2 Modes of Operation BDM is available in all operating modes but must be enabled before firmware commands are executed. Some systems may have a control bit that allows suspending the function during background debug mode. 15.1.2.1 Regular Run Modes All of these operations refer to the part in run mode and not being secured. The BDM does not provide controls to conserve power during run mode. * Normal modes General operation of the BDM is available and operates the same in all normal modes. * Special single chip mode In special single chip mode, background operation is enabled and active out of reset. This allows programming a system with blank memory. * Emulation modes In emulation mode, background operation is enabled but not active out of reset. This allows debugging and programming a system in this mode more easily. 15.1.2.2 Secure Mode Operation If the device is in secure mode, the operation of the BDM is reduced to a small subset of its regular run mode operation. Secure operation prevents access to Flash or EEPROM other than allowing erasure. For more information please see Section 15.4.1, "Security". MC9S12XDP512 Data Sheet, Rev. 2.21 570 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) 15.1.2.3 Low-Power Modes The BDM can be used until all bus masters (e.g., CPU or XGATE) are in stop mode. When CPU is in a low power mode (wait or stop mode) all BDM firmware commands as well as the hardware BACKGROUND command can not be used respectively are ignored. In this case the CPU can not enter BDM active mode, and only hardware read and write commands are available. Also the CPU can not enter a low power mode during BDM active mode. If all bus masters are in stop mode, the BDM clocks are stopped as well. When BDM clocks are disabled and one of the bus masters exits from stop mode the BDM clocks will restart and BDM will have a soft reset (clearing the instruction register, any command in progress and disable the ACK function). The BDM is now ready to receive a new command. 15.1.3 Block Diagram A block diagram of the BDM is shown in Figure 15-1. Host System Serial Interface BKGD Data 16-Bit Shift Register Control Register Block Address TRACE BDMACT Instruction Code and Execution Bus Interface and Control Logic Data Control Clocks ENBDM SDV UNSEC CLKSW Standard BDM Firmware LOOKUP TABLE Secured BDM Firmware LOOKUP TABLE BDMSTS Register Figure 15-1. BDM Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 571 Chapter 15 Background Debug Module (S12XBDMV2) 15.2 External Signal Description A single-wire interface pin called the background debug interface (BKGD) pin is used to communicate with the BDM system. During reset, this pin is a mode select input which selects between normal and special modes of operation. After reset, this pin becomes the dedicated serial interface pin for the background debug mode. 15.3 15.3.1 Memory Map and Register Definition Module Memory Map Table 15-1 shows the BDM memory map when BDM is active. Table 15-1. BDM Memory Map Global Address Module Size (Bytes) 0x7FFF00-0x7FFF0B BDM registers 12 0x7FFF0C-0x7FFF0E BDM firmware ROM 3 0x7FFF0F Family ID (part of BDM firmware ROM) 1 0x7FFF10-0x7FFFFF BDM firmware ROM 240 MC9S12XDP512 Data Sheet, Rev. 2.21 572 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) 15.3.2 Register Descriptions A summary of the registers associated with the BDM is shown in Figure 15-2. Registers are accessed by host-driven communications to the BDM hardware using READ_BD and WRITE_BD commands. Global Address Register Name 0x7FFF00 Reserved R Bit 7 6 5 4 3 2 1 Bit 0 X X X X X X 0 0 BDMACT 0 SDV TRACE UNSEC 0 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X CCR7 CCR6 CCR5 CCR4 CCR3 CCR2 CCR1 CCR0 0 0 0 0 0 CCR10 CCR9 CCR8 BGAE BGP6 BGP5 BGP4 BGP3 BGP2 BGP1 BGP0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W 0x7FFF01 BDMSTS R W 0x7FFF02 Reserved R ENBDM CLKSW W 0x7FFF03 Reserved R W 0x7FFF04 Reserved R W 0x7FFF05 Reserved R W 0x7FFF06 BDMCCRL R W 0x7FFF07 BDMCCRH R W 0x7FFF08 BDMGPR R W 0x7FFF09 Reserved R W 0x7FFF0A Reserved R W 0x7FFF0B Reserved R W = Unimplemented, Reserved X = Indeterminate = Implemented (do not alter) 0 = Always read zero Figure 15-2. BDM Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 573 Chapter 15 Background Debug Module (S12XBDMV2) 15.3.2.1 BDM Status Register (BDMSTS) Register Global Address 0x7FFF01 7 R W ENBDM 6 5 4 3 BDMACT 0 SDV TRACE 1 0 0 0 2 1 0 UNSEC 0 0 03 0 2 CLKSW Reset Special Single-Chip Mode 01 Emulation Modes 1 0 0 0 0 1 0 0 All Other Modes 0 0 0 0 0 0 0 0 = Unimplemented, Reserved 0 = Implemented (do not alter) = Always read zero 1 ENBDM is read as 1 by a debugging environment in special single chip mode when the device is not secured or secured but fully erased (Flash and EEPROM). This is because the ENBDM bit is set by the standard firmware before a BDM command can be fully transmitted and executed. 2 CLKSW is read as 1 by a debugging environment in emulation modes when the device is not secured and read as 0 when secured. 3 UNSEC is read as 1 by a debugging environment in special single chip mode when the device is secured and fully erased, else it is 0 and can only be read if not secure (see also bit description). Figure 15-3. BDM Status Register (BDMSTS) Read: All modes through BDM operation when not secured Write: All modes through BDM operation when not secured, but subject to the following: -- ENBDM should only be set via a BDM hardware command if the BDM firmware commands are needed. (This does not apply in special single chip and emulation modes). -- BDMACT can only be set by BDM hardware upon entry into BDM. It can only be cleared by the standard BDM firmware lookup table upon exit from BDM active mode. -- CLKSW can only be written via BDM hardware WRITE_BD commands. -- All other bits, while writable via BDM hardware or standard BDM firmware write commands, should only be altered by the BDM hardware or standard firmware lookup table as part of BDM command execution. Table 15-2. BDMSTS Field Descriptions Field Description 7 ENBDM Enable BDM -- This bit controls whether the BDM is enabled or disabled. When enabled, BDM can be made active to allow firmware commands to be executed. When disabled, BDM cannot be made active but BDM hardware commands are still allowed. 0 BDM disabled 1 BDM enabled Note: ENBDM is set by the firmware out of reset in special single chip mode and by hardware in emulation modes. In special single chip mode with the device secured, this bit will not be set by the firmware until after the EEPROM and Flash erase verify tests are complete. In emulation modes with the device secured, the BDM operations are blocked. MC9S12XDP512 Data Sheet, Rev. 2.21 574 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) Table 15-2. BDMSTS Field Descriptions (continued) Field Description 6 BDMACT BDM Active Status -- This bit becomes set upon entering BDM. The standard BDM firmware lookup table is then enabled and put into the memory map. BDMACT is cleared by a carefully timed store instruction in the standard BDM firmware as part of the exit sequence to return to user code and remove the BDM memory from the map. 0 BDM not active 1 BDM active 4 SDV Shift Data Valid -- This bit is set and cleared by the BDM hardware. It is set after data has been transmitted as part of a firmware or hardware read command or after data has been received as part of a firmware or hardware write command. It is cleared when the next BDM command has been received or BDM is exited. SDV is used by the standard BDM firmware to control program flow execution. 0 Data phase of command not complete 1 Data phase of command is complete 3 TRACE TRACE1 BDM Firmware Command is Being Executed -- This bit gets set when a BDM TRACE1 firmware command is first recognized. It will stay set until BDM firmware is exited by one of the following BDM commands: GO or GO_UNTIL. 0 TRACE1 command is not being executed 1 TRACE1 command is being executed 2 CLKSW Clock Switch -- The CLKSW bit controls which clock the BDM operates with. It is only writable from a hardware BDM command. A minimum delay of 150 cycles at the clock speed that is active during the data portion of the command send to change the clock source should occur before the next command can be send. The delay should be obtained no matter which bit is modified to effectively change the clock source (either PLLSEL bit or CLKSW bit). This guarantees that the start of the next BDM command uses the new clock for timing subsequent BDM communications. Table 15-3 shows the resulting BDM clock source based on the CLKSW and the PLLSEL (PLL select in the CRG module, the bit is part of the CLKSEL register) bits. Note: The BDM alternate clock source can only be selected when CLKSW = 0 and PLLSEL = 1. The BDM serial interface is now fully synchronized to the alternate clock source, when enabled. This eliminates frequency restriction on the alternate clock which was required on previous versions. Refer to the device specification to determine which clock connects to the alternate clock source input. Note: If the acknowledge function is turned on, changing the CLKSW bit will cause the ACK to be at the new rate for the write command which changes it. Note: In emulation mode, the CLKSW bit will be set out of RESET. 1 UNSEC Unsecure -- If the device is secured this bit is only writable in special single chip mode from the BDM secure firmware. It is in a zero state as secure mode is entered so that the secure BDM firmware lookup table is enabled and put into the memory map overlapping the standard BDM firmware lookup table. The secure BDM firmware lookup table verifies that the on-chip EEPROM and Flash EEPROM are erased. This being the case, the UNSEC bit is set and the BDM program jumps to the start of the standard BDM firmware lookup table and the secure BDM firmware lookup table is turned off. If the erase test fails, the UNSEC bit will not be asserted. 0 System is in a secured mode. 1 System is in a unsecured mode. Note: When UNSEC is set, security is off and the user can change the state of the secure bits in the on-chip Flash EEPROM. Note that if the user does not change the state of the bits to "unsecured" mode, the system will be secured again when it is next taken out of reset.After reset this bit has no meaning or effect when the security byte in the Flash EEPROM is configured for unsecure mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 575 Chapter 15 Background Debug Module (S12XBDMV2) Table 15-3. BDM Clock Sources PLLSEL CLKSW 0 0 Bus clock dependent on oscillator 0 1 Bus clock dependent on oscillator 1 0 Alternate clock (refer to the device specification to determine the alternate clock source) 1 1 Bus clock dependent on the PLL 15.3.2.2 BDMCLK BDM CCR LOW Holding Register (BDMCCRL) Register Global Address 0x7FFF06 7 6 5 4 3 2 1 0 CCR7 CCR6 CCR5 CCR4 CCR3 CCR2 CCR1 CCR0 Special Single-Chip Mode 1 1 0 0 1 0 0 0 All Other Modes 0 0 0 0 0 0 0 0 R W Reset Figure 15-4. BDM CCR LOW Holding Register (BDMCCRL) Read: All modes through BDM operation when not secured Write: All modes through BDM operation when not secured NOTE When BDM is made active, the CPU stores the content of its CCRL register in the BDMCCRL register. However, out of special single-chip reset, the BDMCCRL is set to 0xD8 and not 0xD0 which is the reset value of the CCRL register in this CPU mode. Out of reset in all other modes the BDMCCRL register is read zero. When entering background debug mode, the BDM CCR LOW holding register is used to save the low byte of the condition code register of the user's program. It is also used for temporary storage in the standard BDM firmware mode. The BDM CCR LOW holding register can be written to modify the CCR value. MC9S12XDP512 Data Sheet, Rev. 2.21 576 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) 15.3.2.3 BDM CCR HIGH Holding Register (BDMCCRH) Register Global Address 0x7FFF07 R 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 W Reset 2 1 0 CCR10 CCR9 CCR8 0 0 0 = Unimplemented or Reserved Figure 15-5. BDM CCR HIGH Holding Register (BDMCCRH) Read: All modes through BDM operation when not secured Write: All modes through BDM operation when not secured When entering background debug mode, the BDM CCR HIGH holding register is used to save the high byte of the condition code register of the user's program. The BDM CCR HIGH holding register can be written to modify the CCR value. 15.3.2.4 BDM Global Page Index Register (BDMGPR) Register Global Address 0x7FFF08 R W Reset 7 6 5 4 3 2 1 0 BGAE BGP6 BGP5 BGP4 BGP3 BGP2 BGP1 BGP0 0 0 0 0 0 0 0 0 Figure 15-6. BDM Global Page Register (BDMGPR) Read: All modes through BDM operation when not secured Write: All modes through BDM operation when not secured Table 15-4. BDMGPR Field Descriptions Field Description 7 BGAE BDM Global Page Access Enable Bit -- BGAE enables global page access for BDM hardware and firmware read/write instructions The BDM hardware commands used to access the BDM registers (READ_BD_ and WRITE_BD_) can not be used for global accesses even if the BGAE bit is set. 0 BDM Global Access disabled 1 BDM Global Access enabled 6-0 BGP[6:0] BDM Global Page Index Bits 6-0 -- These bits define the extended address bits from 22 to 16. For more detailed information regarding the global page window scheme, please refer to the S12X_MMC Block Guide. 15.3.3 Family ID Assignment The family ID is a 8-bit value located in the firmware ROM (at global address: 0x7FFF0F). The read-only value is a unique family ID which is 0xC1 for S12X devices. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 577 Chapter 15 Background Debug Module (S12XBDMV2) 15.4 Functional Description The BDM receives and executes commands from a host via a single wire serial interface. There are two types of BDM commands: hardware and firmware commands. Hardware commands are used to read and write target system memory locations and to enter active background debug mode, see Section 15.4.3, "BDM Hardware Commands". Target system memory includes all memory that is accessible by the CPU. Firmware commands are used to read and write CPU resources and to exit from active background debug mode, see Section 15.4.4, "Standard BDM Firmware Commands". The CPU resources referred to are the accumulator (D), X index register (X), Y index register (Y), stack pointer (SP), and program counter (PC). Hardware commands can be executed at any time and in any mode excluding a few exceptions as highlighted (see Section 15.4.3, "BDM Hardware Commands") and in secure mode (see Section 15.4.1, "Security"). Firmware commands can only be executed when the system is not secure and is in active background debug mode (BDM). 15.4.1 Security If the user resets into special single chip mode with the system secured, a secured mode BDM firmware lookup table is brought into the map overlapping a portion of the standard BDM firmware lookup table. The secure BDM firmware verifies that the on-chip EEPROM and Flash EEPROM are erased. This being the case, the UNSEC and ENBDM bit will get set. The BDM program jumps to the start of the standard BDM firmware and the secured mode BDM firmware is turned off and all BDM commands are allowed. If the EEPROM or Flash do not verify as erased, the BDM firmware sets the ENBDM bit, without asserting UNSEC, and the firmware enters a loop. This causes the BDM hardware commands to become enabled, but does not enable the firmware commands. This allows the BDM hardware to be used to erase the EEPROM and Flash. BDM operation is not possible in any other mode than special single chip mode when the device is secured. The device can only be unsecured via BDM serial interface in special single chip mode. For more information regarding security, please see the S12X_9SEC Block Guide. 15.4.2 Enabling and Activating BDM The system must be in active BDM to execute standard BDM firmware commands. BDM can be activated only after being enabled. BDM is enabled by setting the ENBDM bit in the BDM status (BDMSTS) register. The ENBDM bit is set by writing to the BDM status (BDMSTS) register, via the single-wire interface, using a hardware command such as WRITE_BD_BYTE. MC9S12XDP512 Data Sheet, Rev. 2.21 578 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) After being enabled, BDM is activated by one of the following1: * Hardware BACKGROUND command * CPU BGND instruction * External instruction tagging mechanism2 * Breakpoint force or tag mechanism2 When BDM is activated, the CPU finishes executing the current instruction and then begins executing the firmware in the standard BDM firmware lookup table. When BDM is activated by a breakpoint, the type of breakpoint used determines if BDM becomes active before or after execution of the next instruction. NOTE If an attempt is made to activate BDM before being enabled, the CPU resumes normal instruction execution after a brief delay. If BDM is not enabled, any hardware BACKGROUND commands issued are ignored by the BDM and the CPU is not delayed. In active BDM, the BDM registers and standard BDM firmware lookup table are mapped to addresses 0x7FFF00 to 0x7FFFFF. BDM registers are mapped to addresses 0x7FFF00 to 0x7FFF0B. The BDM uses these registers which are readable anytime by the BDM. However, these registers are not readable by user programs. 15.4.3 BDM Hardware Commands Hardware commands are used to read and write target system memory locations and to enter active background debug mode. Target system memory includes all memory that is accessible by the CPU such as on-chip RAM, EEPROM, Flash EEPROM, I/O and control registers, and all external memory. Hardware commands are executed with minimal or no CPU intervention and do not require the system to be in active BDM for execution, although, they can still be executed in this mode. When executing a hardware command, the BDM sub-block waits for a free bus cycle so that the background access does not disturb the running application program. If a free cycle is not found within 128 clock cycles, the CPU is momentarily frozen so that the BDM can steal a cycle. When the BDM finds a free cycle, the operation does not intrude on normal CPU operation provided that it can be completed in a single cycle. However, if an operation requires multiple cycles the CPU is frozen until the operation is complete, even though the BDM found a free cycle. The BDM hardware commands are listed in Table 15-5. The READ_BD and WRITE_BD commands allow access to the BDM register locations. These locations are not normally in the system memory map but share addresses with the application in memory. To distinguish between physical memory locations that share the same address, BDM memory resources are enabled just for the READ_BD and WRITE_BD access cycle. This allows the BDM to access BDM locations unobtrusively, even if the addresses conflict with the application memory map. 1. BDM is enabled and active immediately out of special single-chip reset. 2. This method is provided by the S12X_DBG module. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 579 Chapter 15 Background Debug Module (S12XBDMV2) Table 15-5. Hardware Commands Opcode (hex) Data BACKGROUND 90 None Enter background mode if firmware is enabled. If enabled, an ACK will be issued when the part enters active background mode. ACK_ENABLE D5 None Enable Handshake. Issues an ACK pulse after the command is executed. ACK_DISABLE D6 None Disable Handshake. This command does not issue an ACK pulse. READ_BD_BYTE E4 16-bit address Read from memory with standard BDM firmware lookup table in map. 16-bit data out Odd address data on low byte; even address data on high byte. READ_BD_WORD EC 16-bit address Read from memory with standard BDM firmware lookup table in map. 16-bit data out Must be aligned access. READ_BYTE E0 16-bit address Read from memory with standard BDM firmware lookup table out of map. 16-bit data out Odd address data on low byte; even address data on high byte. READ_WORD E8 16-bit address Read from memory with standard BDM firmware lookup table out of map. 16-bit data out Must be aligned access. WRITE_BD_BYTE C4 16-bit address Write to memory with standard BDM firmware lookup table in map. 16-bit data in Odd address data on low byte; even address data on high byte. WRITE_BD_WORD CC 16-bit address Write to memory with standard BDM firmware lookup table in map. 16-bit data in Must be aligned access. WRITE_BYTE C0 16-bit address Write to memory with standard BDM firmware lookup table out of map. 16-bit data in Odd address data on low byte; even address data on high byte. WRITE_WORD C8 16-bit address Write to memory with standard BDM firmware lookup table out of map. 16-bit data in Must be aligned access. Command Description NOTE: If enabled, ACK will occur when data is ready for transmission for all BDM READ commands and will occur after the write is complete for all BDM WRITE commands. 15.4.4 Standard BDM Firmware Commands Firmware commands are used to access and manipulate CPU resources. The system must be in active BDM to execute standard BDM firmware commands, see Section 15.4.2, "Enabling and Activating BDM". Normal instruction execution is suspended while the CPU executes the firmware located in the standard BDM firmware lookup table. The hardware command BACKGROUND is the usual way to activate BDM. As the system enters active BDM, the standard BDM firmware lookup table and BDM registers become visible in the on-chip memory map at 0x7FFF00-0x7FFFFF, and the CPU begins executing the standard BDM firmware. The standard BDM firmware watches for serial commands and executes them as they are received. The firmware commands are shown in Table 15-6. MC9S12XDP512 Data Sheet, Rev. 2.21 580 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) Table 15-6. Firmware Commands Command1 Opcode (hex) Data Description READ_NEXT2 62 16-bit data out Increment X index register by 2 (X = X + 2), then read word X points to. READ_PC 63 16-bit data out Read program counter. READ_D 64 16-bit data out Read D accumulator. READ_X 65 16-bit data out Read X index register. READ_Y 66 16-bit data out Read Y index register. READ_SP 67 16-bit data out Read stack pointer. WRITE_NEXT<f-hel vetica><st-superscri pt> 42 16-bit data in Increment X index register by 2 (X = X + 2), then write word to location pointed to by X. WRITE_PC 43 16-bit data in Write program counter. WRITE_D 44 16-bit data in Write D accumulator. WRITE_X 45 16-bit data in Write X index register. WRITE_Y 46 16-bit data in Write Y index register. WRITE_SP 47 16-bit data in Write stack pointer. GO 08 none Go to user program. If enabled, ACK will occur when leaving active background mode. GO_UNTIL3 0C none Go to user program. If enabled, ACK will occur upon returning to active background mode. TRACE1 10 none Execute one user instruction then return to active BDM. If enabled, ACK will occur upon returning to active background mode. TAGGO -> GO 18 none (Previous enable tagging and go to user program.) This command will be deprecated and should not be used anymore. Opcode will be executed as a GO command. 1 If enabled, ACK will occur when data is ready for transmission for all BDM READ commands and will occur after the write is complete for all BDM WRITE commands. 2 When the firmware command READ_NEXT or WRITE_NEXT is used to access the BDM address space the BDM resources are accessed rather than user code. Writing BDM firmware is not possible. 3 System stop disables the ACK function and ignored commands will not have an ACK-pulse (e.g., CPU in stop or wait mode). The GO_UNTIL command will not get an Acknowledge if CPU executes the wait or stop instruction before the "UNTIL" condition (BDM active again) is reached (see Section 15.4.7, "Serial Interface Hardware Handshake Protocol" last Note). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 581 Chapter 15 Background Debug Module (S12XBDMV2) 15.4.5 BDM Command Structure Hardware and firmware BDM commands start with an 8-bit opcode followed by a 16-bit address and/or a 16-bit data word depending on the command. All the read commands return 16 bits of data despite the byte or word implication in the command name. 8-bit reads return 16-bits of data, of which, only one byte will contain valid data. If reading an even address, the valid data will appear in the MSB. If reading an odd address, the valid data will appear in the LSB. 16-bit misaligned reads and writes are generally not allowed. If attempted by BDM hardware command, the BDM will ignore the least significant bit of the address and will assume an even address from the remaining bits. The following cycle count information is only valid when the external wait function is not used (see wait bit of EBI sub-block). During an external wait the BDM can not steal a cycle. Hence be careful with the external wait function if the BDM serial interface is much faster than the bus, because of the BDM soft-reset after time-out (see Section 15.4.11, "Serial Communication Time Out"). For hardware data read commands, the external host must wait at least 150 bus clock cycles after sending the address before attempting to obtain the read data. This is to be certain that valid data is available in the BDM shift register, ready to be shifted out. For hardware write commands, the external host must wait 150 bus clock cycles after sending the data to be written before attempting to send a new command. This is to avoid disturbing the BDM shift register before the write has been completed. The 150 bus clock cycle delay in both cases includes the maximum 128 cycle delay that can be incurred as the BDM waits for a free cycle before stealing a cycle. For firmware read commands, the external host should wait at least 48 bus clock cycles after sending the command opcode and before attempting to obtain the read data. This includes the potential of extra cycles when the access is external and stretched (+1 to maximum +7 cycles) or to registers of the PRU (port replacement unit) in emulation mode. The 48 cycle wait allows enough time for the requested data to be made available in the BDM shift register, ready to be shifted out. NOTE This timing has increased from previous BDM modules due to the new capability in which the BDM serial interface can potentially run faster than the bus. On previous BDM modules this extra time could be hidden within the serial time. For firmware write commands, the external host must wait 36 bus clock cycles after sending the data to be written before attempting to send a new command. This is to avoid disturbing the BDM shift register before the write has been completed. MC9S12XDP512 Data Sheet, Rev. 2.21 582 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) The external host should wait at least for 76 bus clock cycles after a TRACE1 or GO command before starting any new serial command. This is to allow the CPU to exit gracefully from the standard BDM firmware lookup table and resume execution of the user code. Disturbing the BDM shift register prematurely may adversely affect the exit from the standard BDM firmware lookup table. NOTE If the bus rate of the target processor is unknown or could be changing or the external wait function is used, it is recommended that the ACK (acknowledge function) is used to indicate when an operation is complete. When using ACK, the delay times are automated. Figure 15-7 represents the BDM command structure. The command blocks illustrate a series of eight bit times starting with a falling edge. The bar across the top of the blocks indicates that the BKGD line idles in the high state. The time for an 8-bit command is 8 x 16 target clock cycles.1 Hardware Read 8 Bits AT ~16 TC/Bit 16 Bits AT ~16 TC/Bit Command Address 150-BC Delay 16 Bits AT ~16 TC/Bit Data Next Command 150-BC Delay Hardware Write Command Address Data Next Command 48-BC DELAY Firmware Read Command Next Command Data 36-BC DELAY Firmware Write Command Data Next Command 76-BC Delay GO, TRACE Command Next Command BC = Bus Clock Cycles TC = Target Clock Cycles Figure 15-7. BDM Command Structure 1. Target clock cycles are cycles measured using the target MCU's serial clock rate. See Section 15.4.6, "BDM Serial Interface" and Section 15.3.2.1, "BDM Status Register (BDMSTS)" for information on how serial clock rate is selected. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 583 Chapter 15 Background Debug Module (S12XBDMV2) 15.4.6 BDM Serial Interface The BDM communicates with external devices serially via the BKGD pin. During reset, this pin is a mode select input which selects between normal and special modes of operation. After reset, this pin becomes the dedicated serial interface pin for the BDM. The BDM serial interface is timed using the clock selected by the CLKSW bit in the status register see Section 15.3.2.1, "BDM Status Register (BDMSTS)". This clock will be referred to as the target clock in the following explanation. The BDM serial interface uses a clocking scheme in which the external host generates a falling edge on the BKGD pin to indicate the start of each bit time. This falling edge is sent for every bit whether data is transmitted or received. Data is transferred most significant bit (MSB) first at 16 target clock cycles per bit. The interface times out if 512 clock cycles occur between falling edges from the host. The BKGD pin is a pseudo open-drain pin and has an weak on-chip active pull-up that is enabled at all times. It is assumed that there is an external pull-up and that drivers connected to BKGD do not typically drive the high level. Since R-C rise time could be unacceptably long, the target system and host provide brief driven-high (speedup) pulses to drive BKGD to a logic 1. The source of this speedup pulse is the host for transmit cases and the target for receive cases. The timing for host-to-target is shown in Figure 15-8 and that of target-to-host in Figure 15-9 and Figure 15-10. All four cases begin when the host drives the BKGD pin low to generate a falling edge. Since the host and target are operating from separate clocks, it can take the target system up to one full clock cycle to recognize this edge. The target measures delays from this perceived start of the bit time while the host measures delays from the point it actually drove BKGD low to start the bit up to one target clock cycle earlier. Synchronization between the host and target is established in this manner at the start of every bit time. Figure 15-8 shows an external host transmitting a logic 1 and transmitting a logic 0 to the BKGD pin of a target system. The host is asynchronous to the target, so there is up to a one clock-cycle delay from the host-generated falling edge to where the target recognizes this edge as the beginning of the bit time. Ten target clock cycles later, the target senses the bit level on the BKGD pin. Internal glitch detect logic requires the pin be driven high no later that eight target clock cycles after the falling edge for a logic 1 transmission. Since the host drives the high speedup pulses in these two cases, the rising edges look like digitally driven signals. MC9S12XDP512 Data Sheet, Rev. 2.21 584 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) BDM Clock (Target MCU) Host Transmit 1 Host Transmit 0 Perceived Start of Bit Time Target Senses Bit Earliest Start of Next Bit 10 Cycles Synchronization Uncertainty Figure 15-8. BDM Host-to-Target Serial Bit Timing The receive cases are more complicated. Figure 15-9 shows the host receiving a logic 1 from the target system. Since the host is asynchronous to the target, there is up to one clock-cycle delay from the host-generated falling edge on BKGD to the perceived start of the bit time in the target. The host holds the BKGD pin low long enough for the target to recognize it (at least two target clock cycles). The host must release the low drive before the target drives a brief high speedup pulse seven target clock cycles after the perceived start of the bit time. The host should sample the bit level about 10 target clock cycles after it started the bit time. BDM Clock (Target MCU) Host Drive to BKGD Pin Target System Speedup Pulse High-Impedance High-Impedance High-Impedance Perceived Start of Bit Time R-C Rise BKGD Pin 10 Cycles 10 Cycles Host Samples BKGD Pin Earliest Start of Next Bit Figure 15-9. BDM Target-to-Host Serial Bit Timing (Logic 1) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 585 Chapter 15 Background Debug Module (S12XBDMV2) Figure 15-10 shows the host receiving a logic 0 from the target. Since the host is asynchronous to the target, there is up to a one clock-cycle delay from the host-generated falling edge on BKGD to the start of the bit time as perceived by the target. The host initiates the bit time but the target finishes it. Since the target wants the host to receive a logic 0, it drives the BKGD pin low for 13 target clock cycles then briefly drives it high to speed up the rising edge. The host samples the bit level about 10 target clock cycles after starting the bit time. BDM Clock (Target MCU) Host Drive to BKGD Pin High-Impedance Speedup Pulse Target System Drive and Speedup Pulse Perceived Start of Bit Time BKGD Pin 10 Cycles 10 Cycles Host Samples BKGD Pin Earliest Start of Next Bit Figure 15-10. BDM Target-to-Host Serial Bit Timing (Logic 0) 15.4.7 Serial Interface Hardware Handshake Protocol BDM commands that require CPU execution are ultimately treated at the MCU bus rate. Since the BDM clock source can be asynchronously related to the bus frequency, when CLKSW = 0, it is very helpful to provide a handshake protocol in which the host could determine when an issued command is executed by the CPU. The alternative is to always wait the amount of time equal to the appropriate number of cycles at the slowest possible rate the clock could be running. This sub-section will describe the hardware handshake protocol. The hardware handshake protocol signals to the host controller when an issued command was successfully executed by the target. This protocol is implemented by a 16 serial clock cycle low pulse followed by a brief speedup pulse in the BKGD pin. This pulse is generated by the target MCU when a command, issued by the host, has been successfully executed (see Figure 15-11). This pulse is referred to as the ACK pulse. After the ACK pulse has finished: the host can start the bit retrieval if the last issued command was a read command, or start a new command if the last command was a write command or a control command (BACKGROUND, GO, GO_UNTIL or TRACE1). The ACK pulse is not issued earlier than 32 serial clock cycles after the BDM command was issued. The end of the BDM command is assumed to be the 16th tick of the last bit. This minimum delay assures enough time for the host to perceive the ACK pulse. Note also that, there is no upper limit for the delay between the command and the related ACK pulse, since the command execution depends upon the CPU bus frequency, which in some cases could be very slow MC9S12XDP512 Data Sheet, Rev. 2.21 586 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) compared to the serial communication rate. This protocol allows a great flexibility for the POD designers, since it does not rely on any accurate time measurement or short response time to any event in the serial communication. BDM Clock (Target MCU) 16 Cycles Target Transmits ACK Pulse High-Impedance High-Impedance 32 Cycles Speedup Pulse Minimum Delay From the BDM Command BKGD Pin Earliest Start of Next Bit 16th Tick of the Last Command Bit Figure 15-11. Target Acknowledge Pulse (ACK) NOTE If the ACK pulse was issued by the target, the host assumes the previous command was executed. If the CPU enters wait or stop prior to executing a hardware command, the ACK pulse will not be issued meaning that the BDM command was not executed. After entering wait or stop mode, the BDM command is no longer pending. Figure 15-12 shows the ACK handshake protocol in a command level timing diagram. The READ_BYTE instruction is used as an example. First, the 8-bit instruction opcode is sent by the host, followed by the address of the memory location to be read. The target BDM decodes the instruction. A bus cycle is grabbed (free or stolen) by the BDM and it executes the READ_BYTE operation. Having retrieved the data, the BDM issues an ACK pulse to the host controller, indicating that the addressed byte is ready to be retrieved. After detecting the ACK pulse, the host initiates the byte retrieval process. Note that data is sent in the form of a word and the host needs to determine which is the appropriate byte based on whether the address was odd or even. Target BKGD Pin READ_BYTE Host Byte Address Host (2) Bytes are Retrieved New BDM Command Host Target Target BDM Issues the ACK Pulse (out of scale) BDM Decodes the Command BDM Executes the READ_BYTE Command Figure 15-12. Handshake Protocol at Command Level MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 587 Chapter 15 Background Debug Module (S12XBDMV2) Differently from the normal bit transfer (where the host initiates the transmission), the serial interface ACK handshake pulse is initiated by the target MCU by issuing a negative edge in the BKGD pin. The hardware handshake protocol in Figure 15-11 specifies the timing when the BKGD pin is being driven, so the host should follow this timing constraint in order to avoid the risk of an electrical conflict in the BKGD pin. NOTE The only place the BKGD pin can have an electrical conflict is when one side is driving low and the other side is issuing a speedup pulse (high). Other "highs" are pulled rather than driven. However, at low rates the time of the speedup pulse can become lengthy and so the potential conflict time becomes longer as well. The ACK handshake protocol does not support nested ACK pulses. If a BDM command is not acknowledge by an ACK pulse, the host needs to abort the pending command first in order to be able to issue a new BDM command. When the CPU enters wait or stop while the host issues a hardware command (e.g., WRITE_BYTE), the target discards the incoming command due to the wait or stop being detected. Therefore, the command is not acknowledged by the target, which means that the ACK pulse will not be issued in this case. After a certain time the host (not aware of stop or wait) should decide to abort any possible pending ACK pulse in order to be sure a new command can be issued. Therefore, the protocol provides a mechanism in which a command, and its corresponding ACK, can be aborted. NOTE The ACK pulse does not provide a time out. This means for the GO_UNTIL command that it can not be distinguished if a stop or wait has been executed (command discarded and ACK not issued) or if the "UNTIL" condition (BDM active) is just not reached yet. Hence in any case where the ACK pulse of a command is not issued the possible pending command should be aborted before issuing a new command. See the handshake abort procedure described in Section 15.4.8, "Hardware Handshake Abort Procedure". 15.4.8 Hardware Handshake Abort Procedure The abort procedure is based on the SYNC command. In order to abort a command, which had not issued the corresponding ACK pulse, the host controller should generate a low pulse in the BKGD pin by driving it low for at least 128 serial clock cycles and then driving it high for one serial clock cycle, providing a speedup pulse. By detecting this long low pulse in the BKGD pin, the target executes the SYNC protocol, see Section 15.4.9, "SYNC -- Request Timed Reference Pulse", and assumes that the pending command and therefore the related ACK pulse, are being aborted. Therefore, after the SYNC protocol has been completed the host is free to issue new BDM commands. For Firmware READ or WRITE commands it can not be guaranteed that the pending command is aborted when issuing a SYNC before the corresponding ACK pulse. There is a short latency time from the time the READ or WRITE access begins until it is finished and the corresponding ACK pulse is issued. The latency time depends on the firmware READ or WRITE command that is issued and if the serial interface is running on a different clock rate than the bus. When the SYNC command starts during this latency time the READ or WRITE command will not be aborted, but the corresponding ACK pulse will be aborted. A pending GO, TRACE1 or MC9S12XDP512 Data Sheet, Rev. 2.21 588 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) GO_UNTIL command can not be aborted. Only the corresponding ACK pulse can be aborted by the SYNC command. Although it is not recommended, the host could abort a pending BDM command by issuing a low pulse in the BKGD pin shorter than 128 serial clock cycles, which will not be interpreted as the SYNC command. The ACK is actually aborted when a negative edge is perceived by the target in the BKGD pin. The short abort pulse should have at least 4 clock cycles keeping the BKGD pin low, in order to allow the negative edge to be detected by the target. In this case, the target will not execute the SYNC protocol but the pending command will be aborted along with the ACK pulse. The potential problem with this abort procedure is when there is a conflict between the ACK pulse and the short abort pulse. In this case, the target may not perceive the abort pulse. The worst case is when the pending command is a read command (i.e., READ_BYTE). If the abort pulse is not perceived by the target the host will attempt to send a new command after the abort pulse was issued, while the target expects the host to retrieve the accessed memory byte. In this case, host and target will run out of synchronism. However, if the command to be aborted is not a read command the short abort pulse could be used. After a command is aborted the target assumes the next negative edge, after the abort pulse, is the first bit of a new BDM command. NOTE The details about the short abort pulse are being provided only as a reference for the reader to better understand the BDM internal behavior. It is not recommended that this procedure be used in a real application. Since the host knows the target serial clock frequency, the SYNC command (used to abort a command) does not need to consider the lower possible target frequency. In this case, the host could issue a SYNC very close to the 128 serial clock cycles length. Providing a small overhead on the pulse length in order to assure the SYNC pulse will not be misinterpreted by the target. See Section 15.4.9, "SYNC -- Request Timed Reference Pulse". Figure 15-13 shows a SYNC command being issued after a READ_BYTE, which aborts the READ_BYTE command. Note that, after the command is aborted a new command could be issued by the host computer. READ_BYTE CMD is Aborted by the SYNC Request (Out of Scale) BKGD Pin READ_BYTE Host Memory Address Target SYNC Response From the Target (Out of Scale) READ_STATUS Host BDM Decode and Starts to Execute the READ_BYTE Command Target New BDM Command Host Target New BDM Command Figure 15-13. ACK Abort Procedure at the Command Level NOTE Figure 15-13 does not represent the signals in a true timing scale MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 589 Chapter 15 Background Debug Module (S12XBDMV2) Figure 15-14 shows a conflict between the ACK pulse and the SYNC request pulse. This conflict could occur if a POD device is connected to the target BKGD pin and the target is already in debug active mode. Consider that the target CPU is executing a pending BDM command at the exact moment the POD is being connected to the BKGD pin. In this case, an ACK pulse is issued along with the SYNC command. In this case, there is an electrical conflict between the ACK speedup pulse and the SYNC pulse. Since this is not a probable situation, the protocol does not prevent this conflict from happening. At Least 128 Cycles BDM Clock (Target MCU) ACK Pulse Target MCU Drives to BKGD Pin Host Drives SYNC To BKGD Pin High-Impedance Host and Target Drive to BKGD Pin Electrical Conflict Speedup Pulse Host SYNC Request Pulse BKGD Pin 16 Cycles Figure 15-14. ACK Pulse and SYNC Request Conflict NOTE This information is being provided so that the MCU integrator will be aware that such a conflict could eventually occur. The hardware handshake protocol is enabled by the ACK_ENABLE and disabled by the ACK_DISABLE BDM commands. This provides backwards compatibility with the existing POD devices which are not able to execute the hardware handshake protocol. It also allows for new POD devices, that support the hardware handshake protocol, to freely communicate with the target device. If desired, without the need for waiting for the ACK pulse. The commands are described as follows: * ACK_ENABLE -- enables the hardware handshake protocol. The target will issue the ACK pulse when a CPU command is executed by the CPU. The ACK_ENABLE command itself also has the ACK pulse as a response. * ACK_DISABLE -- disables the ACK pulse protocol. In this case, the host needs to use the worst case delay time at the appropriate places in the protocol. The default state of the BDM after reset is hardware handshake protocol disabled. All the read commands will ACK (if enabled) when the data bus cycle has completed and the data is then ready for reading out by the BKGD serial pin. All the write commands will ACK (if enabled) after the data has been received by the BDM through the BKGD serial pin and when the data bus cycle is complete. See Section 15.4.3, "BDM Hardware Commands" and Section 15.4.4, "Standard BDM Firmware Commands" for more information on the BDM commands. MC9S12XDP512 Data Sheet, Rev. 2.21 590 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) The ACK_ENABLE sends an ACK pulse when the command has been completed. This feature could be used by the host to evaluate if the target supports the hardware handshake protocol. If an ACK pulse is issued in response to this command, the host knows that the target supports the hardware handshake protocol. If the target does not support the hardware handshake protocol the ACK pulse is not issued. In this case, the ACK_ENABLE command is ignored by the target since it is not recognized as a valid command. The BACKGROUND command will issue an ACK pulse when the CPU changes from normal to background mode. The ACK pulse related to this command could be aborted using the SYNC command. The GO command will issue an ACK pulse when the CPU exits from background mode. The ACK pulse related to this command could be aborted using the SYNC command. The GO_UNTIL command is equivalent to a GO command with exception that the ACK pulse, in this case, is issued when the CPU enters into background mode. This command is an alternative to the GO command and should be used when the host wants to trace if a breakpoint match occurs and causes the CPU to enter active background mode. Note that the ACK is issued whenever the CPU enters BDM, which could be caused by a breakpoint match or by a BGND instruction being executed. The ACK pulse related to this command could be aborted using the SYNC command. The TRACE1 command has the related ACK pulse issued when the CPU enters background active mode after one instruction of the application program is executed. The ACK pulse related to this command could be aborted using the SYNC command. 15.4.9 SYNC -- Request Timed Reference Pulse The SYNC command is unlike other BDM commands because the host does not necessarily know the correct communication speed to use for BDM communications until after it has analyzed the response to the SYNC command. To issue a SYNC command, the host should perform the following steps: 1. Drive the BKGD pin low for at least 128 cycles at the lowest possible BDM serial communication frequency (the lowest serial communication frequency is determined by the crystal oscillator or the clock chosen by CLKSW.) 2. Drive BKGD high for a brief speedup pulse to get a fast rise time (this speedup pulse is typically one cycle of the host clock.) 3. Remove all drive to the BKGD pin so it reverts to high impedance. 4. Listen to the BKGD pin for the sync response pulse. Upon detecting the SYNC request from the host, the target performs the following steps: 1. Discards any incomplete command received or bit retrieved. 2. Waits for BKGD to return to a logic one. 3. Delays 16 cycles to allow the host to stop driving the high speedup pulse. 4. Drives BKGD low for 128 cycles at the current BDM serial communication frequency. 5. Drives a one-cycle high speedup pulse to force a fast rise time on BKGD. 6. Removes all drive to the BKGD pin so it reverts to high impedance. The host measures the low time of this 128 cycle SYNC response pulse and determines the correct speed for subsequent BDM communications. Typically, the host can determine the correct communication speed MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 591 Chapter 15 Background Debug Module (S12XBDMV2) within a few percent of the actual target speed and the communication protocol can easily tolerate speed errors of several percent. As soon as the SYNC request is detected by the target, any partially received command or bit retrieved is discarded. This is referred to as a soft-reset, equivalent to a time-out in the serial communication. After the SYNC response, the target will consider the next negative edge (issued by the host) as the start of a new BDM command or the start of new SYNC request. Another use of the SYNC command pulse is to abort a pending ACK pulse. The behavior is exactly the same as in a regular SYNC command. Note that one of the possible causes for a command to not be acknowledged by the target is a host-target synchronization problem. In this case, the command may not have been understood by the target and so an ACK response pulse will not be issued. 15.4.10 Instruction Tracing When a TRACE1 command is issued to the BDM in active BDM, the CPU exits the standard BDM firmware and executes a single instruction in the user code. Once this has occurred, the CPU is forced to return to the standard BDM firmware and the BDM is active and ready to receive a new command. If the TRACE1 command is issued again, the next user instruction will be executed. This facilitates stepping or tracing through the user code one instruction at a time. If an interrupt is pending when a TRACE1 command is issued, the interrupt stacking operation occurs but no user instruction is executed. Once back in standard BDM firmware execution, the program counter points to the first instruction in the interrupt service routine. Be aware when tracing through the user code that the execution of the user code is done step by step but all peripherals are free running. Hence possible timing relations between CPU code execution and occurrence of events of other peripherals no longer exist. Do not trace the CPU instruction BGND used for soft breakpoints. Tracing the BGND instruction will result in a return address pointing to BDM firmware address space. When tracing through user code which contains stop or wait instructions the following will happen when the stop or wait instruction is traced: The CPU enters stop or wait mode and the TRACE1 command can not be finished before leaving the low power mode. This is the case because BDM active mode can not be entered after CPU executed the stop instruction. However all BDM hardware commands except the BACKGROUND command are operational after tracing a stop or wait instruction and still being in stop or wait mode. If system stop mode is entered (all bus masters are in stop mode) no BDM command is operational. As soon as stop or wait mode is exited the CPU enters BDM active mode and the saved PC value points to the entry of the corresponding interrupt service routine. In case the handshake feature is enabled the corresponding ACK pulse of the TRACE1 command will be discarded when tracing a stop or wait instruction. Hence there is no ACK pulse when BDM active mode is entered as part of the TRACE1 command after CPU exited from stop or wait mode. All valid commands sent during CPU being in stop or wait mode or after CPU exited from stop or wait mode will have an ACK pulse. The handshake feature becomes disabled only when system MC9S12XDP512 Data Sheet, Rev. 2.21 592 Freescale Semiconductor Chapter 15 Background Debug Module (S12XBDMV2) stop mode has been reached. Hence after a system stop mode the handshake feature must be enabled again by sending the ACK_ENABLE command. 15.4.11 Serial Communication Time Out The host initiates a host-to-target serial transmission by generating a falling edge on the BKGD pin. If BKGD is kept low for more than 128 target clock cycles, the target understands that a SYNC command was issued. In this case, the target will keep waiting for a rising edge on BKGD in order to answer the SYNC request pulse. If the rising edge is not detected, the target will keep waiting forever without any time-out limit. Consider now the case where the host returns BKGD to logic one before 128 cycles. This is interpreted as a valid bit transmission, and not as a SYNC request. The target will keep waiting for another falling edge marking the start of a new bit. If, however, a new falling edge is not detected by the target within 512 clock cycles since the last falling edge, a time-out occurs and the current command is discarded without affecting memory or the operating mode of the MCU. This is referred to as a soft-reset. If a read command is issued but the data is not retrieved within 512 serial clock cycles, a soft-reset will occur causing the command to be disregarded. The data is not available for retrieval after the time-out has occurred. This is the expected behavior if the handshake protocol is not enabled. However, consider the behavior where the BDM is running in a frequency much greater than the CPU frequency. In this case, the command could time out before the data is ready to be retrieved. In order to allow the data to be retrieved even with a large clock frequency mismatch (between BDM and CPU) when the hardware handshake protocol is enabled, the time out between a read command and the data retrieval is disabled. Therefore, the host could wait for more then 512 serial clock cycles and still be able to retrieve the data from an issued read command. However, once the handshake pulse (ACK pulse) is issued, the time-out feature is re-activated, meaning that the target will time out after 512 clock cycles. Therefore, the host needs to retrieve the data within a 512 serial clock cycles time frame after the ACK pulse had been issued. After that period, the read command is discarded and the data is no longer available for retrieval. Any negative edge in the BKGD pin after the time-out period is considered to be a new command or a SYNC request. Note that whenever a partially issued command, or partially retrieved data, has occurred the time out in the serial communication is active. This means that if a time frame higher than 512 serial clock cycles is observed between two consecutive negative edges and the command being issued or data being retrieved is not complete, a soft-reset will occur causing the partially received command or data retrieved to be disregarded. The next negative edge in the BKGD pin, after a soft-reset has occurred, is considered by the target as the start of a new BDM command, or the start of a SYNC request pulse. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 593 Chapter 15 Background Debug Module (S12XBDMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 594 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) 16.1 Introduction The XINT module decodes the priority of all system exception requests and provides the applicable vector for processing the exception to either the CPU or the XGATE module. The XINT module supports: * I bit and X bit maskable interrupt requests * A non-maskable unimplemented opcode trap * A non-maskable software interrupt (SWI) or background debug mode request * A spurious interrupt vector request * Three system reset vector requests Each of the I bit maskable interrupt requests can be assigned to one of seven priority levels supporting a flexible priority scheme. For interrupt requests that are configured to be handled by the CPU, the priority scheme can be used to implement nested interrupt capability where interrupts from a lower level are automatically blocked if a higher level interrupt is being processed. Interrupt requests configured to be handled by the XGATE module cannot be nested because the XGATE module cannot be interrupted while processing. NOTE The HPRIO register and functionality of the XINT module is no longer supported, since it is superseded by the 7-level interrupt request priority scheme. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 595 Chapter 16 Interrupt (S12XINTV1) 16.1.1 Glossary The following terms and abbreviations are used in the document. Table 16-1. Terminology Term CCR DMA INT IPL ISR MCU XGATE IRQ XIRQ 16.1.2 * * * * * * * * * * * * Condition Code Register (in the S12X CPU) Direct Memory Access Interrupt Interrupt Processing Level Interrupt Service Routine Micro-Controller Unit please refer to the "XGATE Block Guide" refers to the interrupt request associated with the IRQ pin refers to the interrupt request associated with the XIRQ pin Features Interrupt vector base register (IVBR) One spurious interrupt vector (at address vector base1 + 0x0010). 2-113 I bit maskable interrupt vector requests (at addresses vector base + 0x0012-0x00F2). Each I bit maskable interrupt request has a configurable priority level and can be configured to be handled by either the CPU or the XGATE module2. I bit maskable interrupts can be nested, depending on their priority levels. One X bit maskable interrupt vector request (at address vector base + 0x00F4). One non-maskable software interrupt request (SWI) or background debug mode vector request (at address vector base + 0x00F6). One non-maskable unimplemented opcode trap (TRAP) vector (at address vector base + 0x00F8). Three system reset vectors (at addresses 0xFFFA-0xFFFE). Determines the highest priority DMA and interrupt vector requests, drives the vector to the XGATE module or to the bus on CPU request, respectively. Wakes up the system from stop or wait mode when an appropriate interrupt request occurs or whenever XIRQ is asserted, even if X interrupt is masked. XGATE can wake up and execute code, even with the CPU remaining in stop or wait mode. 16.1.3 * Meaning Modes of Operation Run mode This is the basic mode of operation. 1. The vector base is a 16-bit address which is accumulated from the contents of the interrupt vector base register (IVBR, used as upper byte) and 0x00 (used as lower byte). 2. The IRQ interrupt can only be handled by the CPU MC9S12XDP512 Data Sheet, Rev. 2.21 596 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) * * * Wait mode In wait mode, the XINT module is frozen. It is however capable of either waking up the CPU if an interrupt occurs or waking up the XGATE if an XGATE request occurs. Please refer to Section 16.5.3, "Wake Up from Stop or Wait Mode" for details. Stop Mode In stop mode, the XINT module is frozen. It is however capable of either waking up the CPU if an interrupt occurs or waking up the XGATE if an XGATE request occurs. Please refer to Section 16.5.3, "Wake Up from Stop or Wait Mode" for details. Freeze mode (BDM active) In freeze mode (BDM active), the interrupt vector base register is overridden internally. Please refer to Section 16.3.1.1, "Interrupt Vector Base Register (IVBR)" for details. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 597 Chapter 16 Interrupt (S12XINTV1) 16.1.4 Block Diagram Figure 16-1 shows a block diagram of the XINT module. Peripheral Interrupt Requests Wake Up CPU Non I Bit Maskable Channels PRIOLVL2 PRIOLVL1 PRIOLVL0 RQST Priority Decoder Interrupt Requests IVBR New IPL To CPU Vector Address IRQ Channel Current IPL One Set Per Channel (Up to 112 Channels) INT_XGPRIO XGATE Requests Priority Decoder Wake up XGATE Vector ID XGATE Interrupts To XGATE Module RQST DMA Request Route, PRIOLVLn Priority Level = bits from the channel configuration in the associated configuration register INT_XGPRIO = XGATE Interrupt Priority IVBR = Interrupt Vector Base IPL = Interrupt Processing Level Figure 16-1. XINT Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 598 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) 16.2 External Signal Description The XINT module has no external signals. 16.3 Memory Map and Register Definition This section provides a detailed description of all registers accessible in the XINT. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 599 Chapter 16 Interrupt (S12XINTV1) 16.3.1 Register Descriptions This section describes in address order all the XINT registers and their individual bits. Address Register Name 0x0121 IVBR Bit 7 6 5 R INT_XGPRIO R 3 2 0 0 0 0 0 INT_CFADDR R R W 0x0129 INT_CFDATA1 R W 0x012A INT_CFDATA2 R W 0x012B INT_CFDATA3 R W 0x012C INT_CFDATA4 R W 0x012D INT_CFDATA5 R W 0x012E INT_CFDATA6 R W 0x012F INT_CFDATA7 R W 0 INT_CFADDR[7:4] W 0x0128 INT_CFDATA0 Bit 0 XILVL[2:0] W 0x0127 1 IVB_ADDR[7:0] W 0x0126 4 RQST RQST RQST RQST RQST RQST RQST RQST 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] = Unimplemented or Reserved Figure 16-2. XINT Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 600 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) 16.3.1.1 Interrupt Vector Base Register (IVBR) Address: 0x0121 7 6 5 R 3 2 1 0 1 1 1 IVB_ADDR[7:0] W Reset 4 1 1 1 1 1 Figure 16-3. Interrupt Vector Base Register (IVBR) Read: Anytime Write: Anytime Table 16-2. IVBR Field Descriptions Field Description 7-0 Interrupt Vector Base Address Bits -- These bits represent the upper byte of all vector addresses. Out of IVB_ADDR[7:0] reset these bits are set to 0xFF (i.e., vectors are located at 0xFF10-0xFFFE) to ensure compatibility to HCS12. Note: A system reset will initialize the interrupt vector base register with "0xFF" before it is used to determine the reset vector address. Therefore, changing the IVBR has no effect on the location of the three reset vectors (0xFFFA-0xFFFE). Note: If the BDM is active (i.e., the CPU is in the process of executing BDM firmware code), the contents of IVBR are ignored and the upper byte of the vector address is fixed as "0xFF". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 601 Chapter 16 Interrupt (S12XINTV1) 16.3.1.2 XGATE Interrupt Priority Configuration Register (INT_XGPRIO) Address: 0x0126 R 7 6 5 4 3 0 0 0 0 0 0 0 0 0 2 0 0 XILVL[2:0] W Reset 1 0 0 1 = Unimplemented or Reserved Figure 16-4. XGATE Interrupt Priority Configuration Register (INT_XGPRIO) Read: Anytime Write: Anytime Table 16-3. INT_XGPRIO Field Descriptions Field Description 2-0 XILVL[2:0] XGATE Interrupt Priority Level -- The XILVL[2:0] bits configure the shared interrupt level of the DMA interrupts coming from the XGATE module. Out of reset the priority is set to the lowest active level ("1"). Table 16-4. XGATE Interrupt Priority Levels Priority low high XILVL2 XILVL1 XILVL0 Meaning 0 0 0 Interrupt request is disabled 0 0 1 Priority level 1 0 1 0 Priority level 2 0 1 1 Priority level 3 1 0 0 Priority level 4 1 0 1 Priority level 5 1 1 0 Priority level 6 1 1 1 Priority level 7 MC9S12XDP512 Data Sheet, Rev. 2.21 602 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) 16.3.1.3 Interrupt Request Configuration Address Register (INT_CFADDR) Address: 0x0127 7 6 R 4 INT_CFADDR[7:4] W Reset 5 0 0 0 1 3 2 1 0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 16-5. Interrupt Configuration Address Register (INT_CFADDR) Read: Anytime Write: Anytime Table 16-5. INT_CFADDR Field Descriptions Field Description 7-4 Interrupt Request Configuration Data Register Select Bits -- These bits determine which of the 128 INT_CFADDR[7:4] configuration data registers are accessible in the 8 register window at INT_CFDATA0-7. The hexadecimal value written to this register corresponds to the upper nibble of the lower byte of the interrupt vector, i.e., writing 0xE0 to this register selects the configuration data register block for the 8 interrupt vector requests starting with vector (vector base + 0x00E0) to be accessible as INT_CFDATA0-7. Note: Writing all 0s selects non-existing configuration registers. In this case write accesses to INT_CFDATA0-7 will be ignored and read accesses will return all 0. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 603 Chapter 16 Interrupt (S12XINTV1) 16.3.1.4 Interrupt Request Configuration Data Registers (INT_CFDATA0-7) The eight register window visible at addresses INT_CFDATA0-7 contains the configuration data for the block of eight interrupt requests (out of 128) selected by the interrupt configuration address register (INT_CFADDR) in ascending order. INT_CFDATA0 represents the interrupt configuration data register of the vector with the lowest address in this block, while INT_CFDATA7 represents the interrupt configuration data register of the vector with the highest address, respectively. Address: 0x0128 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-6. Interrupt Request Configuration Data Register 0 (INT_CFDATA0) 1 Please refer to the notes following the PRIOLVL[2:0] description below. Address: 0x0129 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-7. Interrupt Request Configuration Data Register 1 (INT_CFDATA1) 1 Please refer to the notes following the PRIOLVL[2:0] description below. Address: 0x012A 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-8. Interrupt Request Configuration Data Register 2 (INT_CFDATA2) 1 Please refer to the notes following the PRIOLVL[2:0] description below. Address: 0x012B 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-9. Interrupt Request Configuration Data Register 3 (INT_CFDATA3) 1 Please refer to the notes following the PRIOLVL[2:0] description below. MC9S12XDP512 Data Sheet, Rev. 2.21 604 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) Address: 0x012C 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-10. Interrupt Request Configuration Data Register 4 (INT_CFDATA4) 1 Please refer to the notes following the PRIOLVL[2:0] description below. Address: 0x012D 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-11. Interrupt Request Configuration Data Register 5 (INT_CFDATA5) 1 Please refer to the notes following the PRIOLVL[2:0] description below. Address: 0x012E 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-12. Interrupt Request Configuration Data Register 6 (INT_CFDATA6) 1 Please refer to the notes following the PRIOLVL[2:0] description below. Address: 0x012F 7 R W Reset RQST 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 PRIOLVL[2:0] 0 0 11 = Unimplemented or Reserved Figure 16-13. Interrupt Request Configuration Data Register 7 (INT_CFDATA7) 1 Please refer to the notes following the PRIOLVL[2:0] description below. Read: Anytime Write: Anytime MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 605 Chapter 16 Interrupt (S12XINTV1) Table 16-6. INT_CFDATA0-7 Field Descriptions Field Description 7 RQST XGATE Request Enable -- This bit determines if the associated interrupt request is handled by the CPU or by the XGATE module. 0 Interrupt request is handled by the CPU 1 Interrupt request is handled by the XGATE module Note: The IRQ interrupt cannot be handled by the XGATE module. For this reason, the configuration register for vector (vector base + 0x00F2) = IRQ vector address) does not contain a RQST bit. Writing a 1 to the location of the RQST bit in this register will be ignored and a read access will return 0. 2-0 Interrupt Request Priority Level Bits -- The PRIOLVL[2:0] bits configure the interrupt request priority level of PRIOLVL[2:0] the associated interrupt request. Out of reset all interrupt requests are enabled at the lowest active level ("1") to provide backwards compatibility with previous HCS12 interrupt controllers. Please also refer to Table 16-7 for available interrupt request priority levels. Note: Write accesses to configuration data registers of unused interrupt channels will be ignored and read accesses will return all 0. For information about what interrupt channels are used in a specific MCU, please refer to the Device User Guide of that MCU. Note: When vectors (vector base + 0x00F0-0x00FE) are selected by writing 0xF0 to INT_CFADDR, writes to INT_CFDATA2-7 (0x00F4-0x00FE) will be ignored and read accesses will return all 0s. The corresponding vectors do not have configuration data registers associated with them. Note: Write accesses to the configuration register for the spurious interrupt vector request (vector base + 0x0010) will be ignored and read accesses will return 0x07 (request is handled by the CPU, PRIOLVL = 7). Table 16-7. Interrupt Priority Levels Priority low high PRIOLVL2 PRIOLVL1 PRIOLVL0 Meaning 0 0 0 Interrupt request is disabled 0 0 1 Priority level 1 0 1 0 Priority level 2 0 1 1 Priority level 3 1 0 0 Priority level 4 1 0 1 Priority level 5 1 1 0 Priority level 6 1 1 1 Priority level 7 MC9S12XDP512 Data Sheet, Rev. 2.21 606 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) 16.4 Functional Description The XINT module processes all exception requests to be serviced by the CPU module. These exceptions include interrupt vector requests and reset vector requests. Each of these exception types and their overall priority level is discussed in the subsections below. 16.4.1 S12X Exception Requests The CPU handles both reset requests and interrupt requests. The XINT contains registers to configure the priority level of each I bit maskable interrupt request which can be used to implement an interrupt priority scheme. This also includes the possibility to nest interrupt requests. A priority decoder is used to evaluate the priority of a pending interrupt request. 16.4.2 Interrupt Prioritization After system reset all interrupt requests with a vector address lower than or equal to (vector base + 0x00F2) are enabled, are set up to be handled by the CPU and have a pre-configured priority level of 1. The exception to this rule is the spurious interrupt vector request at (vector base + 0x0010) which cannot be disabled, is always handled by the CPU and has a fixed priority level of 7. A priority level of 0 effectively disables the associated interrupt request. If more than one interrupt request is configured to the same interrupt priority level the interrupt request with the higher vector address wins the prioritization. The following conditions must be met for an I bit maskable interrupt request to be processed. 1. The local interrupt enabled bit in the peripheral module must be set. 2. The setup in the configuration register associated with the interrupt request channel must meet the following conditions: a) The XGATE request enable bit must be 0 to have the CPU handle the interrupt request. b) The priority level must be set to non zero. c) The priority level must be greater than the current interrupt processing level in the condition code register (CCR) of the CPU (PRIOLVL[2:0] > IPL[2:0]). 3. The I bit in the condition code register (CCR) of the CPU must be cleared. 4. There is no SWI, TRAP, or XIRQ request pending. NOTE All non I bit maskable interrupt requests always have higher priority than I bit maskable interrupt requests. If an I bit maskable interrupt request is interrupted by a non I bit maskable interrupt request, the currently active interrupt processing level (IPL) remains unaffected. It is possible to nest non I bit maskable interrupt requests, e.g., by nesting SWI or TRAP calls. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 607 Chapter 16 Interrupt (S12XINTV1) 16.4.2.1 Interrupt Priority Stack The current interrupt processing level (IPL) is stored in the condition code register (CCR) of the CPU. This way the current IPL is automatically pushed to the stack by the standard interrupt stacking procedure. The new IPL is copied to the CCR from the priority level of the highest priority active interrupt request channel which is configured to be handled by the CPU. The copying takes place when the interrupt vector is fetched. The previous IPL is automatically restored by executing the RTI instruction. 16.4.3 XGATE Requests The XINT module processes all exception requests to be serviced by the XGATE module. The overall priority level of those exceptions is discussed in the subsections below. 16.4.3.1 XGATE Request Prioritization An interrupt request channel is configured to be handled by the XGATE module, if the RQST bit of the associated configuration register is set to 1 (please refer to Section 16.3.1.4, "Interrupt Request Configuration Data Registers (INT_CFDATA0-7)"). The priority level setting (PRIOLVL) for this channel becomes the DMA priority which will be used to determine the highest priority DMA request to be serviced next by the XGATE module. Additionally, DMA interrupts may be raised by the XGATE module by setting one or more of the XGATE channel interrupt flags (using the SIF instruction). This will result in an CPU interrupt with vector address vector base + (2 * channel ID number), where the channel ID number corresponds to the highest set channel interrupt flag, if the XGIE and channel RQST bits are set. The shared interrupt priority for the DMA interrupt requests is taken from the XGATE interrupt priority configuration register (please refer to Section 16.3.1.2, "XGATE Interrupt Priority Configuration Register (INT_XGPRIO)"). If more than one DMA interrupt request channel becomes active at the same time, the channel with the highest vector address wins the prioritization. 16.4.4 Priority Decoders The XINT module contains priority decoders to determine the priority for all interrupt requests pending for the respective target. There are two priority decoders, one for each interrupt request target (CPU, XGATE module). The function of both priority decoders is basically the same with one exception: the priority decoder for the XGATE module does not take the current interrupt processing level into account because XGATE requests cannot be nested. Because the vector is not supplied until the CPU requests it, it is possible that a higher priority interrupt request could override the original exception that caused the CPU to request the vector. In this case, the CPU will receive the highest priority vector and the system will process this exception instead of the original request. MC9S12XDP512 Data Sheet, Rev. 2.21 608 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) If the interrupt source is unknown (for example, in the case where an interrupt request becomes inactive after the interrupt has been recognized, but prior to the vector request), the vector address supplied to the CPU will default to that of the spurious interrupt vector. NOTE Care must be taken to ensure that all exception requests remain active until the system begins execution of the applicable service routine; otherwise, the exception request may not get processed at all or the result may be a spurious interrupt request (vector at address (vector base + 0x0010)). 16.4.5 Reset Exception Requests The XINT supports three system reset exception request types (please refer to CRG for details): 1. Pin reset, power-on reset, low-voltage reset, or illegal address reset 2. Clock monitor reset request 3. COP watchdog reset request 16.4.6 Exception Priority The priority (from highest to lowest) and address of all exception vectors issued by the XINT upon request by the CPU is shown in Table 16-8. Table 16-8. Exception Vector Map and Priority Vector Address1 Source 0xFFFE Pin reset, power-on reset, low-voltage reset, illegal address reset 0xFFFC Clock monitor reset 0xFFFA COP watchdog reset (Vector base + 0x00F8) Unimplemented opcode trap (Vector base + 0x00F6) Software interrupt instruction (SWI) or BDM vector request (Vector base + 0x00F4) XIRQ interrupt request (Vector base + 0x00F2) IRQ interrupt request (Vector base + 0x00F0-0x0012) Device specific I bit maskable interrupt sources (priority determined by the associated configuration registers, in descending order) (Vector base + 0x0010) 1 Spurious interrupt 16 bits vector address based MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 609 Chapter 16 Interrupt (S12XINTV1) 16.5 16.5.1 Initialization/Application Information Initialization After system reset, software should: * Initialize the interrupt vector base register if the interrupt vector table is not located at the default location (0xFF10-0xFFF9). * Initialize the interrupt processing level configuration data registers (INT_CFADDR, INT_CFDATA0-7) for all interrupt vector requests with the desired priority levels and the request target (CPU or XGATE module). It might be a good idea to disable unused interrupt requests. * If the XGATE module is used, setup the XGATE interrupt priority register (INT_XGPRIO) and configure the XGATE module (please refer the XGATE Block Guide for details). * Enable I maskable interrupts by clearing the I bit in the CCR. * Enable the X maskable interrupt by clearing the X bit in the CCR (if required). 16.5.2 Interrupt Nesting The interrupt request priority level scheme makes it possible to implement priority based interrupt request nesting for the I bit maskable interrupt requests handled by the CPU. * I bit maskable interrupt requests can be interrupted by an interrupt request with a higher priority, so that there can be up to seven nested I bit maskable interrupt requests at a time (refer to Figure 16-14 for an example using up to three nested interrupt requests). I bit maskable interrupt requests cannot be interrupted by other I bit maskable interrupt requests per default. In order to make an interrupt service routine (ISR) interruptible, the ISR must explicitly clear the I bit in the CCR (CLI). After clearing the I bit, I bit maskable interrupt requests with higher priority can interrupt the current ISR. An ISR of an interruptible I bit maskable interrupt request could basically look like this: * Service interrupt, e.g., clear interrupt flags, copy data, etc. * Clear I bit in the CCR by executing the instruction CLI (thus allowing interrupt requests with higher priority) * Process data * Return from interrupt by executing the instruction RTI MC9S12XDP512 Data Sheet, Rev. 2.21 610 Freescale Semiconductor Chapter 16 Interrupt (S12XINTV1) 0 Stacked IPL IPL in CCR 0 0 4 0 0 0 4 7 4 3 1 0 7 6 RTI L7 5 4 RTI Processing Levels 3 L3 (Pending) 2 L4 RTI 1 L1 (Pending) 0 RTI Reset Figure 16-14. Interrupt Processing Example 16.5.3 16.5.3.1 Wake Up from Stop or Wait Mode CPU Wake Up from Stop or Wait Mode Every I bit maskable interrupt request which is configured to be handled by the CPU is capable of waking the MCU from stop or wait mode. To determine whether an I bit maskable interrupts is qualified to wake up the CPU or not, the same settings as in normal run mode are applied during stop or wait mode: * If the I bit in the CCR is set, all I bit maskable interrupts are masked from waking up the MCU. * An I bit maskable interrupt is ignored if it is configured to a priority level below or equal to the current IPL in CCR. * I bit maskable interrupt requests which are configured to be handled by the XGATE are not capable of waking up the CPU. An XIRQ request can wake up the MCU from stop or wait mode at anytime, even if the X bit in CCR is set. 16.5.3.2 XGATE Wake Up from Stop or Wait Mode Interrupt request channels which are configured to be handled by the XGATE are capable of waking up the XGATE. Interrupt request channels handled by the XGATE do not affect the state of the CPU. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 611 Chapter 16 Interrupt (S12XINTV1) MC9S12XDP512 Data Sheet, Rev. 2.21 612 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.1 Introduction This section describes the functionality of the module mapping control (MMC) sub-block of the S12X platform. The block diagram of the MMC is shown in Figure 1-1. The MMC module controls the multi-master priority accesses, the selection of internal resources and external space. Internal buses including internal memories and peripherals are controlled in this module. The local address space for each master is translated to a global memory space. 17.1.1 Features The main features of this block are: * Paging capability to support a global 8 Mbytes memory address space * Bus arbitration between the masters CPU, BDM, and XGATE * Simultaneous accesses to different resources1 (internal, external, and peripherals) (see Figure 1-1) * Resolution of target bus access collision * Access restriction control from masters to some targets (e.g., RAM write access protection for user specified areas) * MCU operation mode control * MCU security control * Separate memory map schemes for each master CPU, BDM, and XGATE * ROM control bits to enable the on-chip FLASH or ROM selection * Port replacement registers access control * Generation of system reset when CPU accesses an unimplemented address (i.e., an address which does not belong to any of the on-chip modules) in single-chip modes 17.1.2 Modes of Operation This subsection lists and briefly describes all operating modes supported by the MMC. 17.1.2.1 * Power Saving Modes Run mode MMC is functional during normal run mode. 1. Resources are also called targets. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 613 Chapter 17 Memory Mapping Control (S12XMMCV2) * Wait mode MMC is functional during wait mode. Stop mode MMC is inactive during stop mode. * 17.1.2.2 * Functional Modes Single chip modes In normal and special single chip mode the internal memory is used. External bus is not active. Expanded modes Address, data, and control signals are activated in normal expanded and special test modes when accessing the external bus. Emulation modes External bus is active to emulate via an external tool the normal expanded or the normal single chip mode. * * 17.1.3 Block Diagram Figure 1-1 shows a block diagram of the MMC. BDM EBI CPU XGATE MMC Address Decoder & Priority DBG EEPROM Target Bus Controller FLASH RAM Peripherals Figure 17-1. MMC Block Diagram 17.2 External Signal Description The user is advised to refer to the SoC Guide for port configuration and location of external bus signals. Some pins may not be bonded out in all implementations. MC9S12XDP512 Data Sheet, Rev. 2.21 614 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) Table 1-2 and Table 1-3 outline the pin names and functions. It also provides a brief description of their operation. Table 17-1. External Input Signals Associated with the MMC Signal I/O Description Availability MODC I Mode input MODB I Mode input Latched after RESET (active low) MODA I Mode input EROMCTL I EROM control input ROMCTL I ROM control input Table 17-2. External Output Signals Associated with the MMC Available in Modes Signal I/O Description NS CS0 O Chip select line 0 CS1 O Chip select line 1 CS2 O Chip select line 2 CS3 O Chip select line 3 SS NX ES EX ST (see Table 1-4) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 615 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3 17.3.1 Memory Map and Registers Module Memory Map A summary of the registers associated with the MMC block is shown in Figure 1-2. Detailed descriptions of the registers and bits are given in the subsections that follow. Address Register Name 0x000A MMCCTL0 R Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 CS3E CS2E CS1E CS0E MODC MODB MODA 0 0 0 0 0 GP6 GP5 GP4 GP3 GP2 GP1 GP0 DP15 DP14 DP13 DP12 DP11 DP10 DP9 DP8 0 0 0 0 0 0 0 0 0 0 0 0 0 EROMON ROMHM ROMON 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RP7 RP6 RP5 RP4 RP3 RP2 RP1 RP0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 PIX7 PIX6 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0 0 0 0 0 0 0 0 0 W 0x000B MODE R W 0x0010 GPAGE R 0 W 0x0011 DIRECT R W 0x0012 Reserved R W 0x0013 MMCCTL1 R W 0x0014 Reserved R W 0x0015 Reserved R W 0x0016 RPAGE R W 0x0017 EPAGE R W 0x0030 PPAGE R W 0x0031 Reserved R W = Unimplemented or Reserved Figure 17-2. MMC Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 616 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) Address Register Name 0x011C RAMWPC Bit 7 R RAMXGU R 1 W 0x011E RAMSHL R 1 W 0x011F RAMSHU 5 4 3 2 0 0 0 0 0 XGU6 XGU5 XGU4 XGU3 SHL6 SHL5 SHL4 SHU6 SHU5 SHU4 RPWE W 0x011D 6 R 1 W 1 Bit 0 AVIE AVIF XGU2 XGU1 XGU0 SHL3 SHL2 SHL1 SHL0 SHU3 SHU2 SHU1 SHU0 = Unimplemented or Reserved Figure 17-2. MMC Register Summary 17.3.2 17.3.2.1 Register Descriptions MMC Control Register (MMCCTL0) Address: 0x000A PRR R 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 CS3E CS2E CS1E CS0E 0 0 0 ROMON1 1. ROMON is bit[0] of the register MMCTL1 (see Figure 1-10) = Unimplemented or Reserved Figure 17-3. MMC Control Register (MMCCTL0) Read: Anytime. In emulation modes read operations will return the data from the external bus. In all other modes the data is read from this register. Write: Anytime. In emulation modes write operations will also be directed to the external bus. Table 17-3. Chip Selects Function Activity Chip Modes Register Bit NS CS3E, CS2E, CS1E, CS0E 1 2 Disabled1 SS Disabled NX Enabled 2 ES EX ST Disabled Enabled Enabled Disabled: feature always inactive. Enabled: activity is controlled by the appropriate register bit value. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 617 Chapter 17 Memory Mapping Control (S12XMMCV2) The MMCCTL0 register is used to control external bus functions, i.e., availability of chip selects. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Table 17-4. MMCCTL0 Field Descriptions Field Description 3-0 CS[3:0]E Chip Select Enables -- Each of these bits enables one of the external chip selects CS3, CS2, CS1, and CS0 outputs which are asserted during accesses to specific external addresses. The associated global address ranges are shown in Table 1-6 and Table 1-21 and Figure 1-23. Chip selects are only active if enabled in normal expanded mode, Emulation expanded mode and special test mode. The function disabled in all other operating modes. 0 Chip select is disabled 1 Chip select is enabled Table 17-5. Chip Select Signals 1 Global Address Range Asserted Signal 0x00_0800-0x0F_FFFF CS3 0x10_0000-0x1F_FFFF CS2 0x20_0000-0x3F_FFFF CS1 0x40_0000-0x7F_FFFF CS01 When the internal NVM is enabled (see ROMON in Section 1.3.2.5, "MMC Control Register (MMCCTL1)") the CS0 is not asserted in the space occupied by this on-chip memory block. MC9S12XDP512 Data Sheet, Rev. 2.21 618 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.2 Mode Register (MODE) Address: 0x000B PRR 7 R W Reset 6 5 MODC MODB MODA MODC1 MODB1 MODA1 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 1. External signal (see Table 1-2). = Unimplemented or Reserved Figure 17-4. Mode Register (MODE) Read: Anytime. In emulation modes read operations will return the data read from the external bus. In all other modes the data are read from this register. Write: Only if a transition is allowed (see Figure 1-5). In emulation modes write operations will be also directed to the external bus. The MODE bits of the MODE register are used to establish the MCU operating mode. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Table 17-6. MODE Field Descriptions Field Description 7-5 MODC, MODB, MODA Mode Select Bits -- These bits control the current operating mode during RESET high (inactive). The external mode pins MODC, MODB, and MODA determine the operating mode during RESET low (active). The state of the pins is latched into the respective register bits after the RESET signal goes inactive (see Figure 1-5). Write restrictions exist to disallow transitions between certain modes. Figure 1-5 illustrates all allowed mode changes. Attempting non authorized transitions will not change the MODE bits, but it will block further writes to these register bits except in special modes. Both transitions from normal single-chip mode to normal expanded mode and from emulation single-chip to emulation expanded mode are only executed by writing a value of 0b101 (write once). Writing any other value will not change the MODE bits, but will block further writes to these register bits. Changes of operating modes are not allowed when the device is secured, but it will block further writes to these register bits except in special modes. In emulation modes reading this address returns data from the external bus which has to be driven by the emulator. It is therefore responsibility of the emulator hardware to provide the expected value (i.e. a value corresponding to normal single chip mode while the device is in emulation single-chip mode or a value corresponding to normal expanded mode while the device is in emulation expanded mode). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 619 Chapter 17 Memory Mapping Control (S12XMMCV2) RESET 010 Special Test (ST) 010 1 1 10 0 10 Normal Expanded (NX) 101 Emulation Single-Chip (ES) 001 Emulation Expanded (EX) 011 101 10 1 011 RESET 0 10 RESET RESET 000 001 101 101 010 110 111 Normal Single-Chip (NS) 100 1 00 01 RESET 100 1 01 1 00 Special Single-Chip (SS) 000 000 RESET Transition done by external pins (MODC, MODB, MODA) RESET Transition done by write access to the MODE register 110 111 Illegal (MODC, MODB, MODA) pin values. Do not use. (Reserved for future use). Figure 17-5. Mode Transition Diagram when MCU is Unsecured MC9S12XDP512 Data Sheet, Rev. 2.21 620 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.3 Global Page Index Register (GPAGE) Address: 0x0010 7 R 0 W Reset 0 6 5 4 3 2 1 0 GP6 GP5 GP4 GP3 GP2 GP1 GP0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 17-6. Global Page Index Register (GPAGE) Read: Anytime Write: Anytime The global page index register is used only when the CPU is executing a global instruction (GLDAA, GLDAB, GLDD, GLDS, GLDX, GLDY,GSTAA, GSTAB, GSTD, GSTS, GSTX, GSTY) (see CPU Block Guide). The generated global address is the result of concatenation of the CPU local address [15:0] with the GPAGE register [22:16] (see Figure 1-7). CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] Bit22 Bit16 Bit15 GPAGE Register [6:0] Bit 0 CPU Address [15:0] Figure 17-7. GPAGE Address Mapping Table 17-7. GPAGE Field Descriptions Field Description 6-0 GP[6:0] Global Page Index Bits 6-0 -- These page index bits are used to select which of the 128 64-kilobyte pages is to be accessed. Example 17-1. This example demonstrates usage of the GPAGE register LDAADR MOVB GLDAA EQU $5000 #$14, GPAGE >LDAADR ;Initialize LDADDR to the value of $5000 ;Initialize GPAGE register with the value of $14 ;Load Accu A from the global address $14_5000 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 621 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.4 Direct Page Register (DIRECT) Address: 0x0011 R W Reset 7 6 5 4 3 2 1 0 DP15 DP14 DP13 DP12 DP11 DP10 DP9 DP8 0 0 0 0 0 0 0 0 Figure 17-8. Direct Register (DIRECT) Read: Anytime Write: anytime in special modes, one time only in other modes. This register determines the position of the direct page within the memory map. Table 17-8. DIRECT Field Descriptions Field Description 7-0 DP[15:8] Direct Page Index Bits 15-8 -- These bits are used by the CPU when performing accesses using the direct addressing mode. The bits from this register form bits [15:8] of the address (see Figure 1-9). CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] Bit22 Bit16 Bit15 Bit8 Bit7 Bit0 DP [15:8] CPU Address [15:0] Figure 17-9. DIRECT Address Mapping Bits [22:16] of the global address will be formed by the GPAGE[6:0] bits in case the CPU executes a global instruction in direct addressing mode or by the appropriate local address to the global address expansion (refer to Expansion of the CPU Local Address Map). Example 17-2. This example demonstrates usage of the Direct Addressing Mode by a global instruction LDAADR MOVB MOVB GLDAA EQU $0000 #$80,DIRECT #$14,GPAGE <LDAADR ;Initialize LDADDR with the value of $0000 ;Initialize DIRECT register with the value of $80 ;Initialize GPAGE register with the value of $14 ;Load Accu A from the global address $14_8000 MC9S12XDP512 Data Sheet, Rev. 2.21 622 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.5 MMC Control Register (MMCCTL1) Address: 0x0013 PRR R 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 W Reset 2 1 0 EROMON ROMHM ROMON EROMCTL 0 ROMCTL = Unimplemented or Reserved Figure 17-10. MMC Control Register (MMCCTL1) Read: Anytime. In emulation modes read operations will return the data from the external bus. In all other modes the data are read from this register. Write: Refer to each bit description. In emulation modes write operations will also be directed to the external bus. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Table 17-9. MMCCTL1 Field Descriptions Field 2 EROMON Description Enables emulated Flash or ROM memory in the memory map Write: Never 0 Disables the emulated Flash or ROM in the memory map. 1 Enables the emulated Flash or ROM in the memory map. 1 ROMHM FLASH or ROM only in higher Half of Memory Map Write: Once in normal and emulation modes and anytime in special modes 0 The fixed page of Flash or ROM can be accessed in the lower half of the memory map. Accesses to $4000-$7FFF will be mapped to $7F_4000-$7F_7FFF in the global memory space. 1 Disables access to the Flash or ROM in the lower half of the memory map.These physical locations of the Flash or ROM can still be accessed through the program page window. Accesses to $4000-$7FFF will be mapped to $14_4000-$14_7FFF in the global memory space (external access). 0 ROMON Enable FLASH or ROM in the memory map Write: Once in normal and emulation modes and anytime in special modes 0 Disables the Flash or ROM from the memory map. 1 Enables the Flash or ROM in the memory map. EROMON and ROMON control the visibility of the Flash in the memory map for CPU or BDM (not for XGATE). Both local and global memory maps are affected. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 623 Chapter 17 Memory Mapping Control (S12XMMCV2) Table 17-10. Data Sources when CPU or BDM is Accessing Flash Area Chip Modes ROMON EROMON DATA SOURCE1 Stretch2 Normal Single Chip X X Internal N X 0 Emulation Memory N X 1 Internal Flash 0 X External Application Y 1 X Internal Flash N 0 X External Application Y 1 0 Emulation Memory N 1 1 Internal Flash 0 X External Application 1 X Internal Flash Special Single Chip Emulation Single Chip Normal Expanded Emulation Expanded Special Test N 1 Internal means resources inside the MCU are read/written. Internal Flash means Flash resources inside the MCU are read/written. Emulation memory means resources inside the emulator are read/written (PRU registers, flash replacement, RAM, EEPROM and register space are always considered internal). External application means resources residing outside the MCU are read/written. 2 The external access stretch mechanism is part of the EBI module (refer to EBI Block Guide for details). 17.3.2.6 RAM Page Index Register (RPAGE) Address: 0x0016 R W Reset 7 6 5 4 3 2 1 0 RP7 RP6 RP5 RP4 RP3 RP2 RP1 RP0 1 1 1 1 1 1 0 1 Figure 17-11. RAM Page Index Register (RPAGE) Read: Anytime Write: Anytime The RAM page index register allows accessing up to (1M minus 2K) bytes of RAM in the global memory map by using the eight page index bits to page 4 Kbyte blocks into the RAM page window located in the CPU local memory map from address $1000 to address $1FFF (see Figure 1-12). CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. MC9S12XDP512 Data Sheet, Rev. 2.21 624 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) Global Address [22:0] 0 0 0 Bit19 Bit18 Bit12 Bit11 Bit0 Address [11:0] RPAGE Register [7:0] Address: CPU Local Address or BDM Local Address Figure 17-12. RPAGE Address Mapping NOTE Because RAM page 0 has the same global address as the register space, it is possible to write to registers through the RAM space when RPAGE = $00. Table 17-11. RPAGE Field Descriptions Field Description 7-0 RP[7:0] RAM Page Index Bits 7-0 -- These page index bits are used to select which of the 256 RAM array pages is to be accessed in the RAM Page Window. The reset value of $FD ensures that there is a linear RAM space available between addresses $1000 and $3FFF out of reset. The fixed 4K page from $2000-$2FFF of RAM is equivalent to page 254 (page number $FE). The fixed 4K page from $3000-$3FFF of RAM is equivalent to page 255 (page number $FF). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 625 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.7 EEPROM Page Index Register (EPAGE) Address: 0x0017 R W 7 6 5 4 3 2 1 0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 1 1 1 1 1 1 1 0 Reset Figure 17-13. EEPROM Page Index Register (EPAGE) Read: Anytime Write: Anytime The EEPROM page index register allows accessing up to 256 Kbyte of EEPROM in the global memory map by using the eight page index bits to page 1 Kbyte blocks into the EEPROM page window located in the local CPU memory map from address $0800 to address $0BFF (see Figure 1-14). CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] 0 0 1 0 0 Bit17 Bit16 Bit10 Bit9 Bit0 Address [9:0] EPAGE Register [7:0] Address: CPU Local Address or BDM Local Address Figure 17-14. EPAGE Address Mapping Table 17-12. EPAGE Field Descriptions Field 7-0 EP[7:0] Description EEPROM Page Index Bits 7-0 -- These page index bits are used to select which of the 256 EEPROM array pages is to be accessed in the EEPROM Page Window. The reset value of $FE ensures that there is a linear EEPROM space available between addresses $0800 and $0FFF out of reset. The fixed 1K page $0C00-$0FFF of EEPROM is equivalent to page 255 (page number $FF). MC9S12XDP512 Data Sheet, Rev. 2.21 626 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.8 Program Page Index Register (PPAGE) Address: 0x0030 R W Reset 7 6 5 4 3 2 1 0 PIX7 PIX6 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0 1 1 1 1 1 1 1 0 Figure 17-15. Program Page Index Register (PPAGE) Read: Anytime Write: Anytime The program page index register allows accessing up to 4 Mbyte of FLASH or ROM in the global memory map by using the eight page index bits to page 16 Kbyte blocks into the program page window located in the CPU local memory map from address $8000 to address $BFFF (see Figure 1-16). The CPU has a special access to read and write this register during execution of CALL and RTC instructions. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] 1 Bit21 Bit0 Bit14 Bit13 PPAGE Register [7:0] Address [13:0] Address: CPU Local Address or BDM Local Address Figure 17-16. PPAGE Address Mapping NOTE Writes to this register using the special access of the CALL and RTC instructions will be complete before the end of the instruction execution. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 627 Chapter 17 Memory Mapping Control (S12XMMCV2) Table 17-13. PPAGE Field Descriptions Field 7-0 PIX[7:0] Description Program Page Index Bits 7-0 -- These page index bits are used to select which of the 256 FLASH or ROM array pages is to be accessed in the Program Page Window. The fixed 16K page from $4000-$7FFF (when ROMHM = 0) is the page number $FD. The reset value of $FE ensures that there is linear Flash space available between addresses $4000 and $FFFF out of reset. The fixed 16K page from $C000-$FFFF is the page number $FF. 17.3.2.9 RAM Write Protection Control Register (RAMWPC) Address: 0x011C 7 R W Reset RWPE 0 6 5 4 3 2 0 0 0 0 0 0 0 0 0 0 1 0 AVIE AVIF 0 0 = Unimplemented or Reserved Figure 17-17. RAM Write Protection Control Register (RAMWPC) Read: Anytime Write: Anytime Table 17-14. RAMWPC Field Descriptions Field Description 7 RWPE RAM Write Protection Enable -- This bit enables the RAM write protection mechanism. When the RWPE bit is cleared, there is no write protection and any memory location is writable by the CPU module and the XGATE module. When the RWPE bit is set the write protection mechanism is enabled and write access of the CPU or to the XGATE RAM region. Write access performed by the XGATE module to outside of the XGATE RAM region or the shared region is suppressed as well in this case. 0 RAM write protection check is disabled, region boundary registers can be written. 1 RAM write protection check is enabled, region boundary registers cannot be written. 1 AVIE CPU Access Violation Interrupt Enable -- This bit enables the Access Violation Interrupt. If AVIE is set and AVIF is set, an interrupt is generated. 0 CPU Access Violation Interrupt Disabled. 1 CPU Access Violation Interrupt Enabled. 0 AVIF CPU Access Violation Interrupt Flag -- When set, this bit indicates that the CPU has tried to write a memory location inside the XGATE RAM region. This flag can be reset by writing'1' to the AVIF bit location. 0 No access violation by the CPU was detected. 1 Access violation by the CPU was detected. MC9S12XDP512 Data Sheet, Rev. 2.21 628 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.10 RAM XGATE Upper Boundary Register (RAMXGU) Address: 0x011D 7 R 1 W Reset 1 6 5 4 3 2 1 0 XGU6 XGU5 XGU4 XGU3 XGU2 XGU1 XGU0 1 1 1 1 1 1 1 = Unimplemented or Reserved Figure 17-18. RAM XGATE Upper Boundary Register (RAMXGU) Read: Anytime Write: Anytime when RWPE = 0 Table 17-15. RAMXGU Field Descriptions Field Description 6-0 XGU[6:0] XGATE Region Upper Boundary Bits 6-0 -- These bits define the upper boundary of the RAM region allocated to the XGATE module in multiples of 256 bytes. The 256 byte block selected by this register is included in the region. See Figure 1-25 for details. 17.3.2.11 RAM Shared Region Lower Boundary Register (RAMSHL) Address: 0x011E 7 R 1 W Reset 1 6 5 4 3 2 1 0 SHL6 SHL5 SHL4 SHL3 SHL2 SHL1 SHL0 1 1 1 1 1 1 1 = Unimplemented or Reserved Figure 17-19. RAM Shared Region Lower Boundary Register (RAMSHL) Read: Anytime Write: Anytime when RWPE = 0 Table 17-16. RAMSHL Field Descriptions Field Description 6-0 SHL[6:0] RAM Shared Region Lower Boundary Bits 6-0 -- These bits define the lower boundary of the shared memory region in multiples of 256 bytes. The block selected by this register is included in the region. See Figure 1-25 for details. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 629 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.3.2.12 RAM Shared Region Upper Boundary Register (RAMSHU) Address: 0x011F 7 R 1 W Reset 1 6 5 4 3 2 1 0 SHU6 SHU5 SHU4 SHU3 SHU2 SHU1 SHU0 1 1 1 1 1 1 1 = Unimplemented or Reserved Figure 17-20. RAM Shared Region Upper Boundary Register (RAMSHU) Read: Anytime Write: Anytime when RWPE = 0 Table 17-17. RAMSHU Field Descriptions Field Description 6-0 SHU[6:0] RAM Shared Region Upper Boundary Bits 6-0 -- These bits define the upper boundary of the shared memory in multiples of 256 bytes. The block selected by this register is included in the region. See Figure 1-25 for details. 17.4 Functional Description The MMC block performs several basic functions of the S12X sub-system operation: MCU operation modes, priority control, address mapping, select signal generation and access limitations for the system. Each aspect is described in the following subsections. 17.4.1 * * * MCU Operating Mode Normal single-chip mode There is no external bus in this mode. The MCU program is executed from the internal memory and no external accesses are allowed. Special single-chip mode This mode is generally used for debugging single-chip operation, boot-strapping or security related operations. The active background debug mode is in control of the CPU code execution and the BDM firmware is waiting for serial commands sent through the BKGD pin. There is no external bus in this mode. Emulation single-chip mode Tool vendors use this mode for emulation systems in which the user's target application is normal single-chip mode. Code is executed from external or internal memory depending on the set-up of the EROMON bit (see Section 1.3.2.5, "MMC Control Register (MMCCTL1)"). The external bus is active in both cases to allow observation of internal operations (internal visibility). MC9S12XDP512 Data Sheet, Rev. 2.21 630 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) * * * Normal expanded mode The external bus interface is configured as an up to 23-bit address bus, 8 or 16-bit data bus with dedicated bus control and status signals. This mode allows 8 or 16-bit external memory and peripheral devices to be interfaced to the system. The fastest external bus rate is half of the internal bus rate. An external signal can be used in this mode to cause the external bus to wait as desired by the external logic. Emulation expanded mode Tool vendors use this mode for emulation systems in which the user's target application is normal expanded mode. Special test mode This mode is an expanded mode for factory test. 17.4.2 17.4.2.1 Memory Map Scheme CPU and BDM Memory Map Scheme The BDM firmware lookup tables and BDM register memory locations share addresses with other modules; however they are not visible in the memory map during user's code execution. The BDM memory resources are enabled only during the READ_BD and WRITE_BD access cycles to distinguish between accesses to the BDM memory area and accesses to the other modules. (Refer to BDM Block Guide for further details). When MCU enters active BDM mode the BDM firmware lookup tables and the BDM registers become visible in the local memory map between addresses $FF00 and $FFFF and the CPU begins execution of firmware commands or the BDM begins execution of hardware commands. The resources which share memory space with the BDM module will not be visible in the memory map during active BDM mode. Please note that after the MCU enters active BDM mode the BDM firmware lookup tables and the BDM registers will also be visible between addresses $BF00 and $BFFF if the PPAGE register contains value of $FF. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 631 Chapter 17 Memory Mapping Control (S12XMMCV2) CPU or BDM Local Memory Map Global Memory Map $00_0000 2K Registers $00_0800 $00_1000 $0000 RAM 253*4K paged 2K Registers $0800 EEPROM 1K window EPAGE 1M minus Kbytes 2K RAM $0F_E000 8K RAM $0C00 1K EEPROM $10_0000 RAM 4K window EEPROM 255*1K paged RPAGE $2000 $13_FC00 256 Kbytes $1000 1K EEPROM 8K RAM $14_4000 $4000 ROMHM=1 $14_8000 Unpaged Flash External Space No 2.75 Mbytes $14_0000 $40_0000 $8000 Flash 16K window PPAGE PPAGES 253 * 16K Unpaged Flash $FFFF $7F_4000 Reset Vectors 16K Unpaged or PPAGE $FD $7F_8000 16K Unpaged or PPAGE $FE $7F_C000 16K Unpaged or PPAGE $FF $7F_FFFF 4 Mbytes $C000 Figure 17-21. Expansion of the Local Address Map MC9S12XDP512 Data Sheet, Rev. 2.21 632 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.4.2.1.1 Expansion of the Local Address Map Expansion of the CPU Local Address Map The program page index register in MMC allows accessing up to 4 Mbyte of FLASH or ROM in the global memory map by using the eight page index bits to page 256 16 Kbyte blocks into the program page window located from address $8000 to address $BFFF in the local CPU memory map. The page value for the program page window is stored in the PPAGE register. The value of the PPAGE register can be read or written by normal memory accesses as well as by the CALL and RTC instructions (see Section 1.5.1, "CALL and RTC Instructions"). Control registers, vector space and parts of the on-chip memories are located in unpaged portions of the 64-kilobyte local CPU address space. The starting address of an interrupt service routine must be located in unpaged memory unless the user is certain that the PPAGE register will be set to the appropriate value when the service routine is called. However an interrupt service routine can call other routines that are in paged memory. The upper 16-kilobyte block of the local CPU memory space ($C000-$FFFF) is unpaged. It is recommended that all reset and interrupt vectors point to locations in this area or to the other upages sections of the local CPU memory map. Table 1-19 summarizes mapping of the address bus in Flash/External space based on the address, the PPAGE register value and value of the ROMHM bit in the MMCCTL1 register. Table 17-18. Global FLASH/ROM Allocated Local CPU Address ROMHM External Access Global Address $4000-$7FFF 0 No $7F_4000 -$7F_7FFF 1 Yes $14_4000-$14_7FFF N/A No1 $40_0000-$7F_FFFF N/A Yes1 N/A No $8000-$BFFF $C000-$FFFF 1 $7F_C000-$7F_FFFF The internal or the external bus is accessed based on the size of the memory resources implemented on-chip. Please refer to Figure 1-23 for further details. The RAM page index register allows accessing up to 1 Mbyte -2 Kbytes of RAM in the global memory map by using the eight RPAGE index bits to page 4 Kbyte blocks into the RAM page window located in the local CPU memory space from address $1000 to address $1FFF. The EEPROM page index register EPAGE allows accessing up to 256 Kbytes of EEPROM in the system by using the eight EPAGE index bits to page 1 Kbyte blocks into the EEPROM page window located in the local CPU memory space from address $0800 to address $0BFF. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 633 Chapter 17 Memory Mapping Control (S12XMMCV2) Expansion of the BDM Local Address Map PPAGE, RPAGE, and EPAGE registers are also used for the expansion of the BDM local address to the global address. These registers can be read and written by the BDM. The BDM expansion scheme is the same as the CPU expansion scheme. 17.4.2.2 Global Addresses Based on the Global Page CPU Global Addresses Based on the Global Page The seven global page index bits allow access to the full 8 Mbyte address map that can be accessed with 23 address bits. This provides an alternative way to access all of the various pages of FLASH, RAM and EEPROM as well as additional external memory. The GPAGE Register is used only when the CPU is executing a global instruction (see Section 1.3.2.3, "Global Page Index Register (GPAGE)"). The generated global address is the result of concatenation of the CPU local address [15:0] with the GPAGE register [22:16] (see Figure 1-7). BDM Global Addresses Based on the Global Page The seven BDMGPR Global Page index bits allow access to the full 8 Mbyte address map that can be accessed with 23 address bits. This provides an alternative way to access all of the various pages of FLASH, RAM and EEPROM as well as additional external memory. The BDM global page index register (BDMGPR) is used only in the case the CPU is executing a firmware command which uses a global instruction (like GLDD, GSTD) or by a BDM hardware command (like WRITE_W, WRITE_BYTE, READ_W, READ_BYTE). See the BDM Block Guide for further details. The generated global address is a result of concatenation of the BDM local address with the BDMGPR register [22:16] in the case of a hardware command or concatenation of the CPU local address and the BDMGPR register [22:16] in the case of a firmware command (see Figure 1-22). MC9S12XDP512 Data Sheet, Rev. 2.21 634 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) BDM HARDWARE COMMAND Global Address [22:0] Bit22 Bit16 Bit15 Bit0 BDMGPR Register [6:0] BDM Local Address BDM FIRMWARE COMMAND Global Address [22:0] Bit22 Bit16 Bit15 Bit0 BDMGPR Register [6:0] CPU Local Address Figure 17-22. BDMGPR Address Mapping 17.4.2.3 Implemented Memory Map The global memory spaces reserved for the internal resources (RAM, EEPROM, and FLASH) are not determined by the MMC module. Size of the individual internal resources are however fixed in the design of the device cannot be changed by the user. Please refer to the Device User Guide for further details. Figure 17-23 and Table 17-20 show the memory spaces occupied by the on-chip resources. Please note that the memory spaces have fixed top addresses. Table 17-19. Global Implemented Memory Space Internal Resource Bottom Address Top Address Registers $00_0000 $00_07FF RAM $10_0000 minus RAMSIZE1 EEPROM FLASH $14_0000 minus EEPROMSIZE $80_0000 minus $0F_FFFF 2 FLASHSIZE3 $13_FFFF $7F_FFFF 1 RAMSIZE is the hexadecimal value of RAM SIZE in bytes EEPROMSIZE is the hexadecimal value of EEPROM SIZE in bytes 3 FLASHSIZE is the hexadecimal value of FLASH SIZE in bytes 2 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 635 Chapter 17 Memory Mapping Control (S12XMMCV2) When the device is operating in expanded modes except emulation single-chip mode, accesses to the global addresses which are not occupied by the on-chip resources (unimplemented areas or external space) result in accesses to the external bus (see Figure 17-23). In emulation single-chip mode, accesses to the global addresses which are not occupied by the on-chip resources (unimplemented areas) result in accesses to the external bus. CPU accesses to the global addresses which are occupied by the external space result in an illegal access reset (system reset). The BDM accesses to the external space are performed but the data is undefined. In single-chip modes an access to any of the unimplemented areas (see Figure 17-23) by the CPU (except firmware commands) results in an illegal access reset (system reset). The BDM accesses to the unimplemented areas are performed but the data is undefined. Misaligned word accesses to the last location (Top address) of any of the on-chip resource blocks (except RAM) by the CPU is performed in expanded modes. In single-chip modes these accesses (except Flash) result in an illegal access reset (except firmware commands). Misaligned word accesses to the last location (top address) of the on-chip RAM by the CPU is ignored in expanded modes (read of undefined data). In single-chip modes these accesses result in an illegal access reset (except firmware commands). No misaligned word access from the BDM module will occur. These accesses are blocked in the BDM (Refer to BDM Block Guide). Misaligned word accesses to the last location of any global page (64 Kbyte) by using global instructions, is performed by accessing the last byte of the page and the first byte of the same page, considering the above mentioned misaligned access cases. The non internal resources (unimplemented areas or external space) are used to generate the chip selects (CS0,CS1,CS2 and CS3) (see Figure 17-23), which are only active in normal expanded mode, emulation expanded mode, and special test mode (see Section 1.3.2.1, "MMC Control Register (MMCCTL0)"). Table 1-21 shows the address boundaries of each chip select and the relationship with the implemented resources (internal) parameters. Table 17-20. Global Chip Selects Memory Space Chip Selects Bottom Address Top Address CS3 $00_0800 $0F_FFFF minus RAMSIZE1 CS2 $10_0000 $13_FFFF minus EEPROMSIZE2 CS23 $14_0000 $1F_FFFF CS1 $20_0000 $3F_FFFF CS04 $40_0000 $7F_FFFF minus FLASHSIZE5 1 External RPAGE accesses in (NX, EX and ST) External EPAGE accesses in (NX, EX and ST) 3 When ROMHM is set (see ROMHM in Table 1-19) the CS2 is asserted in the space occupied by this on-chip memory block. 4 When the internal NVM is enabled (see ROMON in Section 1.3.2.5, "MMC Control Register (MMCCTL1)") the CS0 is not asserted in the space occupied by this on-chip memory block. 5 External PPAGE accesses in (NX, EX and ST) 2 MC9S12XDP512 Data Sheet, Rev. 2.21 636 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) CPU and BDM Local Memory Map Global Memory Map $00_0000 2K Registers $00_0800 CS3 Unimplemented RAM 2K Registers RAM $0800 EEPROM 1K window EPAGE RAMSIZE $0000 $0F_FFFF $0C00 $2000 EEPROM $13_FFFF 8K RAM $1F_FFFF CS1 External Space $4000 CS2 RPAGE EEPROMSIZE Unimplemented EEPROM $1000 RAM 4K window CS2 1K EEPROM Unpaged Flash $40_0000 Flash 16K window CS0 $8000 Unimplemented FLASH PPAGE $C000 $FFFF Reset Vectors FLASH FLASHSIZE Unpaged Flash $7F_FFFF Figure 17-23. Local to Implemented Global Address Mapping (Without GPAGE) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 637 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.4.2.4 17.4.2.4.1 XGATE Memory Map Scheme Expansion of the XGATE Local Address Map The XGATE 64 Kbyte memory space allows access to internal resources only (Registers, RAM, and FLASH). The 2 Kilobyte register address range is the same register address range as for the CPU and the BDM module . XGATE can access the FLASH in single chip modes, even when the MCU is secured. In expanded modes, XGATE can not access the FLASH when MCU is secured. The local address of the XGATE RAM access is translated to the global RAM address range. The XGATE shares the RAM resource with the CPU and the BDM module. The local address of the XGATE FLASH access is translated to the global address as shown in Figure 17-24. For the implemented memory spaces and addresses please refer to Table 1-4 and Table 1-5. MC9S12XDP512 Data Sheet, Rev. 2.21 638 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) XGATE Local Memory Map Global Memory Map $00_0000 2K Registers $00_0800 $0800 RAM $0F_FFFF XGRAMSIZE 2K Registers RAMSIZE $0000 RAM $FFFF FLASH FLASHSIZE 2K XGRAMSIZE FLASH $7F_FFFF Figure 17-24. Local to Global Address Mapping (XGATE) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 639 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.4.3 17.4.3.1 Chip Access Restrictions Illegal XGATE Accesses A possible access error is flagged by the MMC and signalled to XGATE under the following conditions: * XGATE performs misaligned word (in case of load-store or opcode or vector fetch accesses). * XGATE accesses the register space (in case of opcode or vector fetch). * XGATE performs a write to Flash in any modes (in case of load-store access). * XGATE performs an access to a secured Flash in expanded modes (in case of load-store or opcode or vector fetch accesses). * XGATE performs a write to non-XGATE region in RAM (RAM protection mechanism) (in case of load-store access). For further details refer to the XGATE Block Guide. 17.4.3.2 Illegal CPU Accesses After programming the protection mechanism registers (see Figure 1-17, Figure 1-18, Figure 1-19, and Figure 1-20) and setting the RWPE bit (see Figure 1-17) there are 3 regions recognized by the MMC module: 1. XGATE RAM region 2. CPU RAM region 3. Shared Region (XGATE AND CPU) If the RWPE bit is set the CPU write accesses into the XGATE RAM region are blocked. If the CPU tries to write the XGATE RAM region the AVIF bit is set and an interrupt is generated if enabled. Furthermore if the XGATE tries to write to outside of the XGATE RAM or shared regions and the RWPE bit is set, the write access is suppressed and the access error will be flagged to the XGATE module (see Section 1.4.3.1, "Illegal XGATE Accesses" and the XGATE Block Guide). The bottom address of the XGATE RAM region always starts at the lowest implemented RAM address. The values stored in the boundary registers define the boundary addresses in 256 byte steps. The 256 byte block selected by any of the registers is always included in the respective region. For example setting the shared region lower boundary register (RAMSHL) to $C1 and the shared region upper boundary register (RAMSHU) to $E0 defines the shared region from address $0F_C100 to address $0F_E0FF in the global memory space (see Figure 1-25). The interrupt requests generated by the MMC are listed in Table 1-23. Refer to the Device User Guide for the related interrupt vector address and interrupt priority. MC9S12XDP512 Data Sheet, Rev. 2.21 640 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) The following conditions must be satisfied to ensure correct operation of the RAM protection mechanism: * Value stored in RAMXGU must be lower than the value stored in RAMSHL. * Value stored RAMSHL must be lower or equal than the value stored in RAMSHU. Table 17-21. RAM Write Protection Interrupt Vectors Interrupt Source CCR Mask Local Enable CPU access violation I Bit AVIE in RAMWPC $00_0000 2K Registers $00_0800 Unimplemented XGATE RAM Region Only XGATE is allowed to write $0F_RAMXGU_FF RAMSIZE Only CPU is allowed to write $0F_RAMSHL_00 Shared Region CPU and XGATE are allowed to write $0F_RAMSHU_FF Only CPU is allowed to write $0F_FFFF Figure 17-25. RAM Write Protection Scheme MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 641 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.4.4 Chip Bus Control The MMC controls the address buses and the data buses that interface the S12X masters (CPU, BDM and XGATE) with the rest of the system (master buses). In addition the MMC handles all CPU read data bus swapping operations. All internal and external resources are connected to specific target buses (see Figure 1-26). BDM S12X CPU XGATE XGATE S12X MMC XRAM XBus2 XBus1 BDM ROM/REG EBI RAM XBus0 XEEPROM XFLASH IPBI P3 P2 P1 P0 IO 2 Kbyte Registers Figure 17-26. S12X Architecture 17.4.4.1 Master Bus Prioritization The following rules apply when prioritizing accesses over master buses: * The CPU has priority over the BDM, unless the BDM access is stalled for more than 128 cycles. In the later case the CPU will be stalled after finishing the current operation and the BDM will gain access to the bus. * XGATE access to PRU registers constitutes a special case. It is always granted and stalls the CPU and BDM for its duration. MC9S12XDP512 Data Sheet, Rev. 2.21 642 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.4.4.2 Access Conflicts on Target Buses The arbitration scheme allows only one master to be connected to a target at any given time. The following rules apply when prioritizing accesses from different masters to the same target bus: * CPU always has priority over XGATE. * BDM access has priority over XGATE. * XGATE access to PRU registers constitutes a special case. It is always granted and stalls the CPU and BDM for its duration. * In emulation modes all internal accesses are visible on the external bus as well. * During access to the PRU registers, the external bus is reserved. 17.4.5 Interrupts 17.4.5.1 Outgoing Interrupt Requests The following interrupt requests can be triggered by the MMC module: CPU access violation: The CPU access violation signals to the CPU detection of an error condition in the CPU application code which is resulted in write access to the protected XGATE RAM area (see Section 1.4.3.2, "Illegal CPU Accesses"). 17.5 17.5.1 Initialization/Application Information CALL and RTC Instructions CALL and RTC instructions are uninterruptable CPU instructions that automate page switching in the program page window. The CALL instruction is similar to the JSR instruction, but the subroutine that is called can be located anywhere in the local address space or in any Flash or ROM page visible through the program page window. The CALL instruction calculates and stacks a return address, stacks the current PPAGE value and writes a new instruction-supplied value to the PPAGE register. The PPAGE value controls which of the 256 possible pages is visible through the 16 Kbyte program page window in the 64 Kbyte local CPU memory map. Execution then begins at the address of the called subroutine. During the execution of the CALL instruction, the CPU performs the following steps: 1. Writes the current PPAGE value into an internal temporary register and writes the new instruction-supplied PPAGE value into the PPAGE register 2. Calculates the address of the next instruction after the CALL instruction (the return address) and pushes this 16-bit value onto the stack 3. Pushes the temporarily stored PPAGE value onto the stack 4. Calculates the effective address of the subroutine, refills the queue and begins execution at the new address MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 643 Chapter 17 Memory Mapping Control (S12XMMCV2) This sequence is uninterruptable. There is no need to inhibit interrupts during the CALL instruction execution. A CALL instruction can be performed from any address to any other address in the local CPU memory space. The PPAGE value supplied by the instruction is part of the effective address of the CPU. For all addressing mode variations (except indexed-indirect modes) the new page value is provided by an immediate operand in the instruction. In indexed-indirect variations of the CALL instruction a pointer specifies memory locations where the new page value and the address of the called subroutine are stored. Using indirect addressing for both the new page value and the address within the page allows usage of values calculated at run time rather than immediate values that must be known at the time of assembly. The RTC instruction terminates subroutines invoked by a CALL instruction. The RTC instruction unstacks the PPAGE value and the return address and refills the queue. Execution resumes with the next instruction after the CALL instruction. During the execution of an RTC instruction the CPU performs the following steps: 1. Pulls the previously stored PPAGE value from the stack 2. Pulls the 16-bit return address from the stack and loads it into the PC 3. Writes the PPAGE value into the PPAGE register 4. Refills the queue and resumes execution at the return address This sequence is uninterruptable. The RTC can be executed from anywhere in the local CPU memory space. The CALL and RTC instructions behave like JSR and RTS instruction, they however require more execution cycles. Usage of JSR/RTS instructions is therefore recommended when possible and CALL/RTC instructions should only be used when needed. The JSR and RTS instructions can be used to access subroutines that are already present in the local CPU memory map (i.e. in the same page in the program memory page window for example). However calling a function located in a different page requires usage of the CALL instruction. The function must be terminated by the RTC instruction. Because the RTC instruction restores contents of the PPAGE register from the stack, functions terminated with the RTC instruction must be called using the CALL instruction even when the correct page is already present in the memory map. This is to make sure that the correct PPAGE value will be present on stack at the time of the RTC instruction execution. 17.5.2 Port Replacement Registers (PRRs) Registers used for emulation purposes must be rebuilt by the in-circuit emulator hardware to achieve full emulation of single chip mode operation. These registers are called port replacement registers (PRRs) (see Table 1-25). PRRs are accessible from all masters using different access types (word aligned, word-misaligned and byte). Each access to PRRs will be extended to 2 bus cycles for write or read accesses independent of the operating mode. In emulation modes all write operations result in writing into the internal registers (peripheral access) and into the emulated registers (external access) located in the PRU in the emulator at the same time. All read operations are performed from external registers (external access) in emulation modes. In all other modes the read operations are performed from the internal registers (peripheral access). MC9S12XDP512 Data Sheet, Rev. 2.21 644 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) Due to internal visibility of CPU accesses the CPU will be halted during XGATE or BDM access to any PRR. This rule applies also in normal modes to ensure that operation of the device is the same as in emulation modes. A summary of PRR accesses is the following: * An aligned word access to a PRR will take 2 bus cycles. * A misaligned word access to a PRRs will take 4 cycles. If one of the two bytes accessed by the misaligned word access is not a PRR, the access will take only 3 cycles. * A byte access to a PRR will take 2 cycles. Table 17-22. PRR Listing PRR Name PRR Local Address PRR Location PORTA $0000 PIM PORTB $0001 PIM DDRA $0002 PIM DDRB $0003 PIM PORTC $0004 PIM PORTD $0005 PIM DDRC $0006 PIM DDRD $0007 PIM PORTE $0008 PIM DDRE $0009 PIM MMCCTL0 $000A MMC MODE $000B MMC PUCR $000C PIM RDRIV $000D PIM EBICTL0 $000E EBI EBICTL1 $000F EBI Reserved $0012 MMC MMCCTL1 $0013 MMC ECLKCTL $001C PIM Reserved $001D PIM PORTK $0032 PIM DDRK $0033 PIM MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 645 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.5.3 On-Chip ROM Control The MCU offers two modes to support emulation. In the first mode (called generator) the emulator provides the data instead of the internal FLASH and traces the CPU actions. In the other mode (called observer) the internal FLASH provides the data and all internal actions are made visible to the emulator. 17.5.3.1 ROM Control in Single-Chip Modes In single-chip modes the MCU has no external bus. All memory accesses and program fetches are internal (see Figure 1-27). MCU No External Bus Flash Figure 17-27. ROM in Single Chip Modes 17.5.3.2 ROM Control in Emulation Single-Chip Mode In emulation single-chip mode the external bus is connected to the emulator. If the EROMON bit is set, the internal FLASH provides the data and the emulator can observe all internal CPU actions on the external bus. If the EROMON bit is cleared, the emulator provides the data (generator) and traces the all CPU actions (see Figure 1-28). Observer MCU Emulator Flash EROMON = 1 Generator MCU Emulator Flash EROMON = 0 Figure 17-28. ROM in Emulation Single-Chip Mode MC9S12XDP512 Data Sheet, Rev. 2.21 646 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) 17.5.3.3 ROM Control in Normal Expanded Mode In normal expanded mode the external bus will be connected to the application. If the ROMON bit is set, the internal FLASH provides the data. If the ROMON bit is cleared, the application memory provides the data (see Figure 1-29). MCU Application Flash Memory ROMON = 1 MCU Application Memory ROMON = 0 Figure 17-29. ROM in Normal Expanded Mode MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 647 Chapter 17 Memory Mapping Control (S12XMMCV2) 17.5.3.4 ROM Control in Emulation Expanded Mode In emulation expanded mode the external bus will be connected to the emulator and to the application. If the ROMON bit is set, the internal FLASH provides the data. If the EROMON bit is set as well the emulator observes all CPU internal actions, otherwise the emulator provides the data and traces all CPU actions (see Figure 1-30). When the ROMON bit is cleared, the application memory provides the data and the emulator will observe the CPU internal actions (see Figure 1-31). Observer MCU Emulator Flash Application Memory EROMON = 1 Generator MCU Emulator Flash Application Memory EROMON = 0 Figure 17-30. ROMON = 1 in Emulation Expanded Mode MC9S12XDP512 Data Sheet, Rev. 2.21 648 Freescale Semiconductor Chapter 17 Memory Mapping Control (S12XMMCV2) Observer MCU Emulator Application Memory Figure 17-31. ROMON = 0 in Emulation Expanded Mode 17.5.3.5 ROM Control in Special Test Mode In special test mode the external bus is connected to the application. If the ROMON bit is set, the internal FLASH provides the data, otherwise the application memory provides the data (see Figure 1-32). Application MCU Memory ROMON = 0 Application MCU Flash Memory ROMON = 1 Figure 17-32. ROM in Special Test Mode MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 649 Chapter 17 Memory Mapping Control (S12XMMCV2) MC9S12XDP512 Data Sheet, Rev. 2.21 650 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.1 Introduction This section describes the functionality of the module mapping control (MMC) sub-block of the S12X platform. The block diagram of the MMC is shown in Figure 18-1. The MMC module controls the multi-master priority accesses, the selection of internal resources and external space. Internal buses, including internal memories and peripherals, are controlled in this module. The local address space for each master is translated to a global memory space. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 651 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.1.1 Terminology Table 18-1. Acronyms and Abbreviations Logic level "1" Voltage that corresponds to Boolean true state Logic level "0" Voltage that corresponds to Boolean false state 0x Represents hexadecimal number x Represents logic level 'don't care' byte 8-bit data word 16-bit data local address based on the 64 KBytes Memory Space (16-bit address) global address based on the 8 MBytes Memory Space (23-bit address) Aligned address Address on even boundary Mis-aligned address Address on odd boundary Bus Clock System Clock. Refer to CRG Block Guide. expanded modes Normal Expanded Mode Emulation Single-Chip Mode Emulation Expanded Mode Special Test Mode single-chip modes Normal Single-Chip Mode Special Single-Chip Mode emulation modes Emulation Single-Chip Mode Emulation Expanded Mode normal modes Normal Single-Chip Mode Normal Expanded Mode special modes Special Single-Chip Mode Special Test Mode NS Normal Single-Chip Mode SS Special Single-Chip Mode NX Normal Expanded Mode ES Emulation Single-Chip Mode EX Emulation Expanded Mode ST Special Test Mode Unimplemented areas External Space external resource 18.1.2 Areas which are accessible by the pages (RPAGE,PPAGE,EPAGE) and not implemented Area which is accessible in the global address range 14_0000 to 3F_FFFF Resources (Emulator, Application) connected to the MCU via the external bus on expanded modes (Unimplemented areas and External Space) PRR Port Replacement Registers PRU Port Replacement Unit located on the emulator side MCU MicroController Unit NVM Non-volatile Memory; Flash EEPROM or ROM Features The main features of this block are: * Paging capability to support a global 8 Mbytes memory address space * Bus arbitration between the masters CPU, BDM and XGATE MC9S12XDP512 Data Sheet, Rev. 2.21 652 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) * * * * * * * * * Simultaneous accesses to different resources1 (internal, external, and peripherals) (see ) Resolution of target bus access collision Access restriction control from masters to some targets (e.g., RAM write access protection for user specified areas) MCU operation mode control MCU security control Separate memory map schemes for each master CPU, BDM and XGATE ROM control bits to enable the on-chip FLASH or ROM selection Port replacement registers access control Generation of system reset when CPU accesses an unimplemented address (i.e., an address which does not belong to any of the on-chip modules) in single-chip modes 18.1.3 S12X Memory Mapping The S12X architecture implements a number of memory mapping schemes including * a CPU 8 MByte global map, defined using a global page (GPAGE) register and dedicated 23-bit address load/store instructions. * a BDM 8 MByte global map, defined using a global page (BDMGPR) register and dedicated 23-bit address load/store instructions. * a (CPU or BDM) 64 KByte local map, defined using specific resource page (RPAGE, EPAGE and PPAGE) registers and the default instruction set. The 64 KBytes visible at any instant can be considered as the local map accessed by the 16-bit (CPU or BDM) address. * The XGATE 64 Kbyte local map. The MMC module performs translation of the different memory mapping schemes to the specific global (physical) memory implementation. 18.1.4 Modes of Operation This subsection lists and briefly describes all operating modes supported by the MMC. 18.1.4.1 * * * Power Saving Modes Run mode MMC is functional during normal run mode. Wait mode MMC is functional during wait mode. Stop mode MMC is inactive during stop mode. 1. Resources are also called targets. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 653 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.1.4.2 * Functional Modes Single chip modes In normal and special single chip mode the internal memory is used. External bus is not active. Expanded modes Address, data, and control signals are activated in normal expanded and special test modes when accessing the external bus. Access to internal resources will not cause activity on the external bus. Emulation modes External bus is active to emulate, via an external tool, the normal expanded or the normal single chip mode. * * 18.1.5 Block Diagram Figure 18-11 shows a block diagram of the MMC. BDM CPU XGATE FLEXRAY EEPROM MMC FLASH Address Decoder & Priority DBG Target Bus Controller EBI RAM Peripherals Figure 18-1. MMC Block Diagram 18.2 External Signal Description The user is advised to refer to the SoC Guide for port configuration and location of external bus signals. Some pins may not be bonded out in all implementations. Table 18-2 and Table 18-3 outline the pin names and functions. It also provides a brief description of their operation. 1. Doted blocks and lines are optional. Please refer to the Device User Guide for their availlibilities. MC9S12XDP512 Data Sheet, Rev. 2.21 654 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) Table 18-2. External Input Signals Associated with the MMC Signal I/O Description Availability MODC I Mode input Latched after RESET (active low) MODB I Mode input Latched after RESET (active low) MODA I Mode input Latched after RESET (active low) EROMCTL I EROM control input Latched after RESET (active low) ROMCTL I ROM control input Latched after RESET (active low) Table 18-3. External Output Signals Associated with the MMC Available in Modes Signal I/O Description NS CS0 O Chip select line 0 CS1 O Chip select line 1 CS2 O Chip select line 2 CS3 O Chip select line 3 SS NX ES EX ST (see Table 18-4) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 655 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3 18.3.1 Memory Map and Registers Module Memory Map A summary of the registers associated with the MMC block is shown in Figure 18-2. Detailed descriptions of the registers and bits are given in the subsections that follow. Address Register Name 0x000A MMCCTL0 R Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 CS3E CS2E CS1E CS0E MODC MODB MODA 0 0 0 0 0 GP6 GP5 GP4 GP3 GP2 GP1 GP0 DP15 DP14 DP13 DP12 DP11 DP10 DP9 DP8 0 0 0 0 0 0 0 0 0 0 0 0 0 EROMON ROMHM ROMON 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RP7 RP6 RP5 RP4 RP3 RP2 RP1 RP0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 PIX7 PIX6 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0 0 0 0 0 0 0 0 0 W 0x000B MODE R W 0x0010 GPAGE R 0 W 0x0011 DIRECT R W 0x0012 Reserved R W 0x0013 MMCCTL1 R W 0x0014 Reserved R W 0x0015 Reserved R W 0x0016 RPAGE R W 0x0017 EPAGE R W 0x0030 PPAGE R W 0x0031 Reserved R W = Unimplemented or Reserved Figure 18-2. MMC Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 656 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) Address Register Name 0x011D RAMXGU Bit 7 R 1 W 0x011E RAMSHL R 1 W 0x011F RAMSHU R 1 W 6 5 4 3 2 1 Bit 0 XGU6 XGU5 XGU4 XGU3 XGU2 XGU1 XGU0 SHL6 SHL5 SHL4 SHL3 SHL2 SHL1 SHL0 SHU6 SHU5 SHU4 SHU3 SHU2 SHU1 SHU0 = Unimplemented or Reserved Figure 18-2. MMC Register Summary 18.3.2 18.3.2.1 Register Descriptions MMC Control Register (MMCCTL0) Address: 0x000A PRR R 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 CS3E CS2E CS1E CS0E 0 0 0 ROMON1 1. ROMON is bit[0] of the register MMCTL1 (see Figure 18-10) = Unimplemented or Reserved Figure 18-3. MMC Control Register (MMCCTL0) Read: Anytime. In emulation modes read operations will return the data from the external bus. In all other modes the data is read from this register. Write: Anytime. In emulation modes write operations will also be directed to the external bus. Table 18-4. Chip Selects Function Activity Chip Modes Register Bit CS3E, CS2E, CS1E, CS0E 1 2 NS SS NX ES EX ST Disabled1 Disabled Enabled2 Disabled Enabled Enabled Disabled: feature always inactive. Enabled: activity is controlled by the appropriate register bit value. The MMCCTL0 register is used to control external bus functions, i.e., availability of chip selects. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 657 Chapter 18 Memory Mapping Control (S12XMMCV3) Table 18-5. MMCCTL0 Field Descriptions Field Description 3-0 CS[3:0]E Chip Select Enables -- Each of these bits enables one of the external chip selects CS3, CS2, CS1, and CS0 outputs which are asserted during accesses to specific external addresses. The associated global address ranges are shown in Table 18-6 and Table 18-21 and Figure 18-21. Chip selects are only active if enabled in normal expanded mode, Emulation expanded mode and special test mode. The function disabled in all other operating modes. 0 Chip select is disabled 1 Chip select is enabled Table 18-6. Chip Select Signals 1 Global Address Range Asserted Signal 0x00_0800-0x0F_FFFF CS3 0x10_0000-0x1F_FFFF CS2 0x20_0000-0x3F_FFFF CS1 0x40_0000-0x7F_FFFF CS01 When the internal NVM is enabled (see ROMON in Section 18.3.2.5, "MMC Control Register (MMCCTL1)) the CS0 is not asserted in the space occupied by this on-chip memory block. MC9S12XDP512 Data Sheet, Rev. 2.21 658 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3.2.2 Mode Register (MODE) Address: 0x000B PRR 7 R W Reset 6 5 MODC MODB MODA MODC1 MODB1 MODA1 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 1. External signal (see Table 18-2). = Unimplemented or Reserved Figure 18-4. Mode Register (MODE) Read: Anytime. In emulation modes read operations will return the data read from the external bus. In all other modes the data are read from this register. Write: Only if a transition is allowed (see Figure 18-5). In emulation modes write operations will be also directed to the external bus. The MODE bits of the MODE register are used to establish the MCU operating mode. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Table 18-7. MODE Field Descriptions Field Description 7-5 MODC, MODB, MODA Mode Select Bits -- These bits control the current operating mode during RESET high (inactive). The external mode pins MODC, MODB, and MODA determine the operating mode during RESET low (active). The state of the pins is latched into the respective register bits after the RESET signal goes inactive (see Figure 18-5). Write restrictions exist to disallow transitions between certain modes. Figure 18-5 illustrates all allowed mode changes. Attempting non authorized transitions will not change the MODE bits, but it will block further writes to these register bits except in special modes. Both transitions from normal single-chip mode to normal expanded mode and from emulation single-chip to emulation expanded mode are only executed by writing a value of 3'b101 (write once). Writing any other value will not change the MODE bits, but will block further writes to these register bits. Changes of operating modes are not allowed when the device is secured, but it will block further writes to these register bits except in special modes. In emulation modes reading this address returns data from the external bus which has to be driven by the emulator. It is therefore responsibility of the emulator hardware to provide the expected value (i.e. a value corresponding to normal single chip mode while the device is in emulation single-chip mode or a value corresponding to normal expanded mode while the device is in emulation expanded mode). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 659 Chapter 18 Memory Mapping Control (S12XMMCV3) RESET 010 Special Test (ST) 010 1 1 10 0 10 Normal Expanded (NX) 101 Emulation Single-Chip (ES) 001 Emulation Expanded (EX) 011 101 10 1 011 RESET 0 10 RESET RESET 000 001 101 101 010 110 111 Normal Single-Chip (NS) 100 1 00 01 RESET 100 1 01 1 00 Special Single-Chip (SS) 000 000 RESET Transition done by external pins (MODC, MODB, MODA) RESET Transition done by write access to the MODE register 110 111 Illegal (MODC, MODB, MODA) pin values. Do not use. (Reserved for future use). Figure 18-5. Mode Transition Diagram when MCU is Unsecured MC9S12XDP512 Data Sheet, Rev. 2.21 660 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3.2.3 Global Page Index Register (GPAGE) Address: 0x0010 7 R 0 W Reset 0 6 5 4 3 2 1 0 GP6 GP5 GP4 GP3 GP2 GP1 GP0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 18-6. Global Page Index Register (GPAGE) Read: Anytime Write: Anytime The global page index register is used to construct a 23 bit address in the global map format. It is only used when the CPU is executing a global instruction (GLDAA, GLDAB, GLDD, GLDS, GLDX, GLDY,GSTAA, GSTAB, GSTD, GSTS, GSTX, GSTY) (see CPU Block Guide). The generated global address is the result of concatenation of the CPU local address [15:0] with the GPAGE register [22:16] (see Figure 18-7). CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] Bit22 Bit16 Bit15 GPAGE Register [6:0] Bit 0 CPU Address [15:0] Figure 18-7. GPAGE Address Mapping Table 18-8. GPAGE Field Descriptions Field Description 6-0 GP[6:0] Global Page Index Bits 6-0 -- These page index bits are used to select which of the 128 64-kilobyte pages is to be accessed. Example 18-1. This example demonstrates usage of the GPAGE register LDX MOVB GLDAA #0x5000 #0x14, GPAGE X ;Set GPAGE offset to the value of 0x5000 ;Initialize GPAGE register with the value of 0x14 ;Load Accu A from the global address 0x14_5000 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 661 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3.2.4 Direct Page Register (DIRECT) Address: 0x0011 R W 7 6 5 4 3 2 1 0 DP15 DP14 DP13 DP12 DP11 DP10 DP9 DP8 0 0 0 0 0 0 0 0 Reset Figure 18-8. Direct Register (DIRECT) Read: Anytime Write: anytime in special modes, one time only in other modes. This register determines the position of the 256 Byte direct page within the memory map.It is valid for both global and local mapping scheme. Table 18-9. DIRECT Field Descriptions Field Description 7-0 DP[15:8] Direct Page Index Bits 15-8 -- These bits are used by the CPU when performing accesses using the direct addressing mode. The bits from this register form bits [15:8] of the address (see Figure 18-9). CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] Bit22 Bit16 Bit15 Bit8 Bit7 Bit0 DP [15:8] CPU Address [15:0] Figure 18-9. DIRECT Address Mapping Bits [22:16] of the global address will be formed by the GPAGE[6:0] bits in case the CPU executes a global instruction in direct addressing mode or by the appropriate local address to the global address expansion (refer to Section 18.4.2.1.1, "Expansion of the Local Address Map). Example 18-2. This example demonstrates usage of the Direct Addressing Mode MOVB #0x80,DIRECT ;Set DIRECT register to 0x80. Write once only. ;Global data accesses to the range 0xXX_80XX can be direct. ;Logical data accesses to the range 0x80XX are direct. LDY <00 ;Load the Y index register from 0x8000 (direct access). ;< operator forces direct access on some assemblers but in ;many cases assemblers are "direct page aware" and can MC9S12XDP512 Data Sheet, Rev. 2.21 662 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) ;automatically select direct mode. 18.3.2.5 MMC Control Register (MMCCTL1) Address: 0x0013 PRR R 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 W Reset 2 1 0 EROMON ROMHM ROMON EROMCTL 0 ROMCTL = Unimplemented or Reserved Figure 18-10. MMC Control Register (MMCCTL1) Read: Anytime. In emulation modes read operations will return the data from the external bus. In all other modes the data are read from this register.Write: Refer to each bit description. In emulation modes write operations will also be directed to the external bus. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Table 18-10. MMCCTL1 Field Descriptions Field Description 2 EROMON Enables emulated Flash or ROM memory in the memory map Write: Never This bit is used in some modes to define the placement of the Emulated Flash or ROM (Refer to Table 18-11) 0 Disables the emulated Flash or ROM in the memory map. 1 Enables the emulated Flash or ROM in the memory map. 1 ROMHM FLASH or ROM only in higher Half of Memory Map Write: Once in normal and emulation modes and anytime in special modes 0 The fixed page of Flash or ROM can be accessed in the lower half of the memory map. Accesses to 0x4000-0x7FFF will be mapped to 0x7F_4000-0x7F_7FFF in the global memory space. 1 Disables access to the Flash or ROM in the lower half of the memory map.These physical locations of the Flash or ROM can still be accessed through the program page window. Accesses to 0x4000-0x7FFF will be mapped to 0x14_4000-0x14_7FFF in the global memory space (external access). 0 ROMON Enable FLASH or ROM in the memory map Write: Once in normal and emulation modes and anytime in special modes. This bit is used in some modes to define the placement of the ROM (Refer to Table 18-11) 0 Disables the Flash or ROM from the memory map. 1 Enables the Flash or ROM in the memory map. EROMON and ROMON control the visibility of the Flash in the memory map for CPU or BDM (not for XGATE). Both local and global memory maps are affected. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 663 Chapter 18 Memory Mapping Control (S12XMMCV3) Table 18-11. Data Sources when CPU or BDM is Accessing Flash Area Chip Modes ROMON EROMON DATA SOURCE1 Stretch2 Normal Single Chip X X Internal Flash N X 0 Emulation Memory N X 1 Internal Flash 0 X External Application Y 1 X Internal Flash N 0 X External Application Y 1 0 Emulation Memory N 1 1 Internal Flash 0 X External Application 1 X Internal Flash Special Single Chip Emulation Single Chip Normal Expanded Emulation Expanded Special Test N 1 Internal Flash means Flash resources inside the MCU are read/written. Emulation memory means resources inside the emulator are read/written (PRU registers, flash replacement, RAM, EEPROM and register space are always considered internal). External application means resources residing outside the MCU are read/written. 2 The external access stretch mechanism is part of the EBI module (refer to EBI Block Guide for details). 18.3.2.6 RAM Page Index Register (RPAGE) Address: 0x0016 R W Reset 7 6 5 4 3 2 1 0 RP7 RP6 RP5 RP4 RP3 RP2 RP1 RP0 1 1 1 1 1 1 0 1 Figure 18-11. RAM Page Index Register (RPAGE) Read: Anytime Write: Anytime These eight index bits are used to page 4 KByte blocks into the RAM page window located in the local (CPU or BDM) memory map from address 0x1000 to address 0x1FFF (see Figure 18-12). This supports accessing up to 1022 Kbytes of RAM (in the Global map) within the 64 KByte Local map. The RAM page index register is effectively used to construct paged RAM addresses in the Local map format. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. MC9S12XDP512 Data Sheet, Rev. 2.21 664 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) Global Address [22:0] 0 0 0 Bit19 Bit18 Bit12 Bit11 Bit0 Address [11:0] RPAGE Register [7:0] Address: CPU Local Address or BDM Local Address Figure 18-12. RPAGE Address Mapping NOTE Because RAM page 0 has the same global address as the register space, it is possible to write to registers through the RAM space when RPAGE = 0x00. Table 18-12. RPAGE Field Descriptions Field Description 7-0 RP[7:0] RAM Page Index Bits 7-0 -- These page index bits are used to select which of the 256 RAM array pages is to be accessed in the RAM Page Window. The reset value of 0xFD ensures that there is a linear RAM space available between addresses 0x1000 and 0x3FFF out of reset. The fixed 4K page from 0x2000-0x2FFF of RAM is equivalent to page 254 (page number 0xFE). The fixed 4K page from 0x3000-0x3FFF of RAM is equivalent to page 255 (page number 0xFF). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 665 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3.2.7 EEPROM Page Index Register (EPAGE) Address: 0x0017 R W 7 6 5 4 3 2 1 0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 1 1 1 1 1 1 1 0 Reset Figure 18-13. EEPROM Page Index Register (EPAGE) Read: Anytime Write: Anytime These eight index bits are used to page 1 KByte blocks into the EEPROM page window located in the local (CPU or BDM) memory map from address 0x0800 to address 0x0BFF (see Figure 18-14). This supports accessing up to 256 Kbytes of EEPROM (in the Global map) within the 64 KByte Local map. The EEPROM page index register is effectively used to construct paged EEPROM addresses in the Local map format. CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] 0 0 1 0 0 Bit17 Bit16 Bit10 Bit9 Bit0 Address [9:0] EPAGE Register [7:0] Address: CPU Local Address or BDM Local Address Figure 18-14. EPAGE Address Mapping Table 18-13. EPAGE Field Descriptions Field 7-0 EP[7:0] Description EEPROM Page Index Bits 7-0 -- These page index bits are used to select which of the 256 EEPROM array pages is to be accessed in the EEPROM Page Window. The reset value of 0xFE ensures that there is a linear EEPROM space available between addresses 0x0800 and 0x0FFF out of reset. The fixed 1K page 0x0C00-0x0FFF of EEPROM is equivalent to page 255 (page number 0xFF). MC9S12XDP512 Data Sheet, Rev. 2.21 666 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3.2.8 Program Page Index Register (PPAGE) Address: 0x0030 R W Reset 7 6 5 4 3 2 1 0 PIX7 PIX6 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0 1 1 1 1 1 1 1 0 Figure 18-15. Program Page Index Register (PPAGE) Read: Anytime Write: Anytime These eight index bits are used to page 16 KByte blocks into the Flash page window located in the local (CPU or BDM) memory map from address 0x8000 to address 0xBFFF (see Figure 18-16). This supports accessing up to 4 Mbytes of Flash (in the Global map) within the 64 KByte Local map. The PPAGE age index register is effectively used to construct paged Flash addresses in the Local map format. The CPU has special access to read and write this register directly during execution of CALL and RTC instructions. . CAUTION XGATE write access to this register during an CPU access which makes use of this register could lead to unexpected results. Global Address [22:0] 1 Bit21 Bit0 Bit14 Bit13 PPAGE Register [7:0] Address [13:0] Address: CPU Local Address or BDM Local Address Figure 18-16. PPAGE Address Mapping NOTE Writes to this register using the special access of the CALL and RTC instructions will be complete before the end of the instruction execution. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 667 Chapter 18 Memory Mapping Control (S12XMMCV3) Table 18-14. PPAGE Field Descriptions Field 7-0 PIX[7:0] Description Program Page Index Bits 7-0 -- These page index bits are used to select which of the 256 FLASH or ROM array pages is to be accessed in the Program Page Window. The fixed 16K page from 0x4000-0x7FFF (when ROMHM = 0) is the page number 0xFD. The reset value of 0xFE ensures that there is linear Flash space available between addresses 0x4000 and 0xFFFF out of reset. The fixed 16K page from 0xC000-0xFFFF is the page number 0xFF. 18.3.2.9 RAM Write Protection Control Register (RAMWPC) Address: 0x011C Reset 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 18-17. RAM Write Protection Control Register (RAMWPC) Read: Anytime Write: Anytime Table 18-15. RAMWPC Field Descriptions Field Description 0 RWPE RAM Write Protection Enable -- This bit enables the RAM write protection mechanism. When the RWPE bit is cleared, there is no write protection and any memory location is writable by the CPU module and the XGATE module. When the RWPE bit is set the write protection mechanism is enabled and write access of the CPU or to the XGATE RAM region. Write access performed by the XGATE module to outside of the XGATE RAM region or the shared region is suppressed as well in this case. 0 RAM write protection check is disabled, region boundary registers can be written. 1 RAM write protection check is enabled, region boundary registers cannot be written. 1 AVIE CPU Access Violation Interrupt Enable -- This bit enables the Access Violation Interrupt. If AVIE is set and AVIF is set, an interrupt is generated. 0 CPU Access Violation Interrupt Disabled. 1 CPU Access Violation Interrupt Enabled. 0 AVIF CPU Access Violation Interrupt Flag -- When set, this bit indicates that the CPU has tried to write a memory location inside the XGATE RAM region. This flag can be reset by writing '1' to the AVIF bit location. 0 No access violation by the CPU was detected. 1 Access violation by the CPU was detected. MC9S12XDP512 Data Sheet, Rev. 2.21 668 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3.2.10 RAM XGATE Upper Boundary Register (RAMXGU) Address: 0x011D 7 R 1 W Reset 1 6 5 4 3 2 1 0 XGU6 XGU5 XGU4 XGU3 XGU2 XGU1 XGU0 1 1 1 1 1 1 1 = Unimplemented or Reserved Figure 18-18. RAM XGATE Upper Boundary Register (RAMXGU) Read: Anytime Write: Anytime when RWPE = 0 Table 18-16. RAMXGU Field Descriptions Field Description 6-0 XGU[6:0] XGATE Region Upper Boundary Bits 6-0 -- These bits define the upper boundary of the RAM region allocated to the XGATE module in multiples of 256 bytes. The 256 byte block selected by this register is included in the region. See Figure 18-25 for details. 18.3.2.11 RAM Shared Region Lower Boundary Register (RAMSHL) Address: 0x011E 7 R 1 W Reset 1 6 5 4 3 2 1 0 SHL6 SHL5 SHL4 SHL3 SHL2 SHL1 SHL0 1 1 1 1 1 1 1 = Unimplemented or Reserved Figure 18-19. RAM Shared Region Lower Boundary Register (RAMSHL) Read: Anytime Write: Anytime when RWPE = 0 Table 18-17. RAMSHL Field Descriptions Field Description 6-0 SHL[6:0] RAM Shared Region Lower Boundary Bits 6-0 -- These bits define the lower boundary of the shared memory region in multiples of 256 bytes. The block selected by this register is included in the region. See Figure 18-25 for details. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 669 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.3.2.12 RAM Shared Region Upper Boundary Register (RAMSHU) Address: 0x011F 7 R 1 W Reset 1 6 5 4 3 2 1 0 SHU6 SHU5 SHU4 SHU3 SHU2 SHU1 SHU0 1 1 1 1 1 1 1 = Unimplemented or Reserved Figure 18-20. RAM Shared Region Upper Boundary Register (RAMSHU) Read: Anytime Write: Anytime when RWPE = 0 Table 18-18. RAMSHU Field Descriptions Field Description 6-0 SHU[6:0] RAM Shared Region Upper Boundary Bits 6-0 -- These bits define the upper boundary of the shared memory in multiples of 256 bytes. The block selected by this register is included in the region. See Figure 18-25 for details. MC9S12XDP512 Data Sheet, Rev. 2.21 670 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.4 Functional Description The MMC block performs several basic functions of the S12X sub-system operation: MCU operation modes, priority control, address mapping, select signal generation and access limitations for the system. Each aspect is described in the following subsections. 18.4.1 * * * MCU Operating Mode Normal single-chip mode There is no external bus in this mode. The MCU program is executed from the internal memory and no external accesses are allowed. Special single-chip mode This mode is generally used for debugging single-chip operation, boot-strapping or security related operations. The active background debug mode is in control of the CPU code execution and the BDM firmware is waiting for serial commands sent through the BKGD pin. There is no external bus in this mode. Emulation single-chip mode Tool vendors use this mode for emulation systems in which the user's target application is normal single-chip mode. Code is executed from external or internal memory depending on the set-up of the EROMON bit (see Section 18.3.2.5, "MMC Control Register (MMCCTL1)). The external bus is active in both cases to allow observation of internal operations (internal visibility). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 671 Chapter 18 Memory Mapping Control (S12XMMCV3) * * * Normal expanded mode The external bus interface is configured as an up to 23-bit address bus, 8 or 16-bit data bus with dedicated bus control and status signals. This mode allows 8 or 16-bit external memory and peripheral devices to be interfaced to the system. The fastest external bus rate is half of the internal bus rate. An external signal can be used in this mode to cause the external bus to wait as desired by the external logic. Emulation expanded mode Tool vendors use this mode for emulation systems in which the user's target application is normal expanded mode. Special test mode This mode is an expanded mode for factory test. 18.4.2 18.4.2.1 Memory Map Scheme CPU and BDM Memory Map Scheme The BDM firmware lookup tables and BDM register memory locations share addresses with other modules; however they are not visible in the memory map during user's code execution. The BDM memory resources are enabled only during the READ_BD and WRITE_BD access cycles to distinguish between accesses to the BDM memory area and accesses to the other modules. (Refer to BDM Block Guide for further details). When the MCU enters active BDM mode, the BDM firmware lookup tables and the BDM registers become visible in the local memory map in the range 0xFF00-0xFFFF (global address 0x7F_FF00 0x7F_FFFF) and the CPU begins execution of firmware commands or the BDM begins execution of hardware commands. The resources which share memory space with the BDM module will not be visible in the memory map during active BDM mode. Please note that after the MCU enters active BDM mode the BDM firmware lookup tables and the BDM registers will also be visible between addresses 0xBF00 and 0xBFFF if the PPAGE register contains value of 0xFF. MC9S12XDP512 Data Sheet, Rev. 2.21 672 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) CPU and BDM Local Memory Map Global Memory Map 0x00_0000 0x00_0800 2K REGISTERS 2K RAM RAM 253*4K paged 0x0800 0x0C00 0x1000 0x0F_E000 2K REGISTERS 1K EEPROM window 8K RAM EPAGE 0x10_0000 1K EEPROM 4K RAM window EEPROM 255*1K paged RPAGE 0x2000 8K RAM 0x4000 0x13_FC00 256 Kilobytes 0x0000 1M minus 2 Kilobytes 0x00_1000 1K EEPROM External Space 0x8000 16K FLASH window 2.75 Mbytes 0x14_0000 Unpaged 16K FLASH PPAGE 0x40_0000 0xC000 0xFFFF Reset Vectors 0x7F_4000 0x7F_8000 0x7F_C000 16K FLASH (PPAGE 0xFD) 4 Mbytes FLASH 253 *16K paged Unpaged 16K FLASH 16K FLASH (PPAGE 0xFE) 16K FLASH (PPAGE 0xFF) 0x7F_FFFF Figure 18-21. Expansion of the Local Address Map MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 673 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.4.2.1.1 Expansion of the Local Address Map Expansion of the CPU Local Address Map The program page index register in MMC allows accessing up to 4 Mbyte of FLASH or ROM in the global memory map by using the eight page index bits to page 256 16 Kbyte blocks into the program page window located from address 0x8000 to address 0xBFFF in the local CPU memory map. The page value for the program page window is stored in the PPAGE register. The value of the PPAGE register can be read or written by normal memory accesses as well as by the CALL and RTC instructions (see Section 18.5.1, "CALL and RTC Instructions). Control registers, vector space and parts of the on-chip memories are located in unpaged portions of the 64-kilobyte local CPU address space. The starting address of an interrupt service routine must be located in unpaged memory unless the user is certain that the PPAGE register will be set to the appropriate value when the service routine is called. However an interrupt service routine can call other routines that are in paged memory. The upper 16-kilobyte block of the local CPU memory space (0xC000-0xFFFF) is unpaged. It is recommended that all reset and interrupt vectors point to locations in this area or to the other unpaged sections of the local CPU memory map. Table 18-19 Table 18-12 summarizes mapping of the address bus in Flash/External space based on the address, the PPAGE register value and value of the ROMHM bit in the MMCCTL1 register. Table 18-19. Global FLASH/ROM Allocated Local CPU Address ROMHM External Access Global Address 0x4000-0x7FFF 0 No 0x7F_4000 -0x7F_7FFF 1 Yes 0x14_4000-0x14_7FFF N/A No1 0x40_0000-0x7F_FFFF N/A Yes1 N/A No 0x8000-0xBFFF 0xC000-0xFFFF 1 0x7F_C000-0x7F_FFFF The internal or the external bus is accessed based on the size of the memory resources implemented on-chip. Please refer to Figure 1-23 for further details. The RAM page index register allows accessing up to 1 Mbyte -2 Kbytes of RAM in the global memory map by using the eight RPAGE index bits to page 4 Kbyte blocks into the RAM page window located in the local CPU memory space from address 0x1000 to address 0x1FFF. The EEPROM page index register EPAGE allows accessing up to 256 Kbytes of EEPROM in the system by using the eight EPAGE index bits to page 1 Kbyte blocks into the EEPROM page window located in the local CPU memory space from address 0x0800 to address 0x0BFF. MC9S12XDP512 Data Sheet, Rev. 2.21 674 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) Expansion of the BDM Local Address Map PPAGE, RPAGE, and EPAGE registers are also used for the expansion of the BDM local address to the global address. These registers can be read and written by the BDM. The BDM expansion scheme is the same as the CPU expansion scheme. 18.4.2.2 Global Addresses Based on the Global Page CPU Global Addresses Based on the Global Page The seven global page index bits allow access to the full 8 Mbyte address map that can be accessed with 23 address bits. This provides an alternative way to access all of the various pages of FLASH, RAM and EEPROM as well as additional external memory. The GPAGE Register is used only when the CPU is executing a global instruction (see Section 18.3.2.3, "Global Page Index Register (GPAGE)). The generated global address is the result of concatenation of the CPU local address [15:0] with the GPAGE register [22:16] (see Figure 18-7). BDM Global Addresses Based on the Global Page The seven BDMGPR Global Page index bits allow access to the full 8 Mbyte address map that can be accessed with 23 address bits. This provides an alternative way to access all of the various pages of FLASH, RAM and EEPROM as well as additional external memory. The BDM global page index register (BDMGPR) is used only in the case the CPU is executing a firmware command which uses a global instruction (like GLDD, GSTD) or by a BDM hardware command (like WRITE_W, WRITE_BYTE, READ_W, READ_BYTE). See the BDM Block Guide for further details. The generated global address is a result of concatenation of the BDM local address with the BDMGPR register [22:16] in the case of a hardware command or concatenation of the CPU local address and the BDMGPR register [22:16] in the case of a firmware command (see Figure 18-22). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 675 Chapter 18 Memory Mapping Control (S12XMMCV3) BDM HARDWARE COMMAND Global Address [22:0] Bit22 Bit16 Bit15 BDMGPR Register [6:0] Bit0 BDM Local Address BDM FIRMWARE COMMAND Global Address [22:0] Bit22 Bit16 Bit15 BDMGPR Register [6:0] Bit0 CPU Local Address Figure 18-22. BDMGPR Address Mapping MC9S12XDP512 Data Sheet, Rev. 2.21 676 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.4.2.3 Implemented Memory Map The global memory spaces reserved for the internal resources (RAM, EEPROM, and FLASH) are not determined by the MMC module. Size of the individual internal resources are however fixed in the design of the device cannot be changed by the user. Please refer to the Device User Guide for further details. Figure 18-23 and Table 18-20 show the memory spaces occupied by the on-chip resources. Please note that the memory spaces have fixed top addresses. Table 18-20. Global Implemented Memory Space 1 2 Internal Resource $Address RAM RAM_LOW = 0x10_0000 minus RAMSIZE1 EEPROM EEPROM_LOW = 0x14_0000 minus EEPROMSIZE2 RAMSIZE is the hexadecimal value of RAM SIZE in bytes EEPROMSIZE is the hexadecimal value of EEPROM SIZE in bytes When the device is operating in expanded modes except emulation single-chip mode, accesses to global addresses which are not occupied by the on-chip resources (unimplemented areas or external memory space) result in accesses to the external bus (see Figure 18-23). In emulation single-chip mode, accesses to global addresses which are not occupied by the on-chip resources (unimplemented areas) result in accesses to the external bus. CPU accesses to global addresses which are occupied by external memory space result in an illegal access reset (system reset). BDM accesses to the external space are performed but the data will be undefined. In single-chip modes accesses by the CPU (except for firmware commands) to any of the unimplemented areas (see Figure 18-23) will result in an illegal access reset (system reset). BDM accesses to the unimplemented areas are allowed but the data will be undefined. No misaligned word access from the BDM module will occur; these accesses are blocked in the BDM module (Refer to BDM Block Guide). Misaligned word access to the last location of RAM is performed but the data will be undefined. Misaligned word access to the last location of any global page (64 Kbyte) by any global instruction, is performed by accessing the last byte of the page and the first byte of the same page, considering the above mentioned misaligned access cases. The non-internal resources (unimplemented areas or external space) are used to generate the chip selects (CS0,CS1,CS2 and CS3) (see Figure 18-23), which are only active in normal expanded, emulation expanded and special test modes (see Section 18.3.2.1, "MMC Control Register (MMCCTL0)). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 677 Chapter 18 Memory Mapping Control (S12XMMCV3) Table 18-21 shows the address boundaries of each chip select and the relationship with the implemented resources (internal) parameters. Table 18-21. Global Chip Selects Memory Space Chip Selects Bottom Address Top Address CS3 0x00_0800 0x0F_FFFF minus RAMSIZE1 CS2 0x10_0000 0x13_FFFF minus EEPROMSIZE2 CS23 0x14_0000 0x1F_FFFF CS1 0x20_0000 0x3F_FFFF 4 0x40_0000 0x7F_FFFF minus FLASHSIZE5 CS0 1 External RPAGE accesses in (NX, EX and ST) External EPAGE accesses in (NX, EX and ST) 3 When ROMHM is set (see ROMHM in Table 18-19) the CS2 is asserted in the space occupied by this on-chip memory block. 4 When the internal NVM is enabled (see ROMON in Section 18.3.2.5, "MMC Control Register (MMCCTL1)) the CS0 is not asserted in the space occupied by this on-chip memory block. 5 External PPAGE accesses in (NX, EX and ST) 2 Figure 18-23. Local to Implemented Global Address Mapping (Without GPAGE) 18.4.2.4 18.4.2.4.1 XGATE Memory Map Scheme Expansion of the XGATE Local Address Map The XGATE 64 Kbyte memory space allows access to internal resources only (Registers, RAM, and FLASH). The 2 Kilobyte register address range is the same register address range as for the CPU and the BDM module . XGATE can access the FLASH in single chip modes, even when the MCU is secured. In expanded modes, XGATE can not access the FLASH when MCU is secured. The local address of the XGATE RAM access is translated to the global RAM address range. The XGATE shares the RAM resource with the CPU and the BDM module . The local address of the XGATE FLASH access is translated to the global address as shown in Figure 18-24. For the implemented memory spaces and addresses please refer to Table 1-4 and Table 1-5. MC9S12XDP512 Data Sheet, Rev. 2.21 678 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) XGATE Local Memory Map Global Memory Map 0x00_0000 Registers 0x00_07FF XGRAM_LOW 0x0800 RAM 0x0F_FFFF RAMSIZE Registers XGRAMSIZE 0x0000 FLASH 0x78_0800 FLASH XGFLASH_HIGH 0xFFFF XGFLASHSIZE RAM 0x7F_FFFF Figure 18-24. XGATE Global Address Mapping MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 679 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.4.3 18.4.3.1 Chip Access Restrictions Illegal XGATE Accesses A possible access error is flagged by the MMC and signalled to XGATE under the following conditions: * XGATE performs misaligned word (in case of load-store or opcode or vector fetch accesses). * XGATE accesses the register space (in case of opcode or vector fetch). * XGATE performs a write to Flash in any modes (in case of load-store access). * XGATE performs an access to a secured Flash in expanded modes (in case of load-store or opcode or vector fetch accesses). * XGATE performs an access to an unimplemented area (in case of load-store or opcode or vector fetch accesses). * XGATE performs a write to non-XGATE region in RAM (RAM protection mechanism) (in case of load-store access). For further details refer to the XGATE Block Guide. 18.4.3.2 Illegal CPU Accesses After programming the protection mechanism registers (see Figure 18-17, Figure 18-18, Figure 18-19, and Figure 18-20) and setting the RWPE bit (see Figure 18-17) there are 3 regions recognized by the MMC module: 1. XGATE RAM region 2. CPU RAM region 3. Shared Region (XGATE AND CPU) If the RWPE bit is set the CPU write accesses into the XGATE RAM region are blocked. If the CPU tries to write the XGATE RAM region the AVIF bit is set and an interrupt is generated if enabled. Furthermore if the XGATE tries to write to outside of the XGATE RAM or shared regions and the RWPE bit is set, the write access is suppressed and the access error will be flagged to the XGATE module (see Section 18.4.3.1, "Illegal XGATE Accesses and the XGATE Block Guide). The bottom address of the XGATE RAM region always starts at the lowest implemented RAM address. The values stored in the boundary registers define the boundary addresses in 256 byte steps. The 256 byte block selected by any of the registers is always included in the respective region. For example setting the shared region lower boundary register (RAMSHL) to 0xC1 and the shared region upper boundary register (RAMSHU) to 0xE0 defines the shared region from address 0x0F_C100 to address 0x0F_E0FF in the global memory space (see Figure 18-20). The interrupt requests generated by the MMC are listed in Table 18-22. Refer to the Device User Guide for the related interrupt vector address and interrupt priority. The following conditions must be satisfied to ensure correct operation of the RAM protection mechanism: * Value stored in RAMXGU must be lower than the value stored in RAMSHL. * Value stored RAMSHL must be lower or equal than the value stored in RAMSHU. MC9S12XDP512 Data Sheet, Rev. 2.21 680 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) Table 18-22. RAM Write Protection Interrupt Vectors Interrupt Source CCR Mask Local Enable CPU access violation I Bit AVIE in RAMWPC Figure 18-25. RAM write protection scheme MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 681 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.4.4 Chip Bus Control The MMC controls the address buses and the data buses that interface the S12X masters (CPU, BDMand XGATE) with the rest of the system (master buses). In addition the MMC handles all CPU read data bus swapping operations. All internal and external resources are connected to specific target buses (see Figure 18-261). BDM CPU DBG XGATE XGATE FLEXRAY S12X1 S12X0 S12X2 MMC "Crossbar Switch" EBI XBUS0 XBUS1 BLKX XBUS3 FTX FLASH EETX XRAM BDM resources XSRAM XBUS2 IPBI Figure 18-26. MMC Block Diagram 1. Doted blocks and lines are optional. Please refer to the Device User Guide for their availlibilities. MC9S12XDP512 Data Sheet, Rev. 2.21 682 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.4.4.1 Master Bus Prioritization regarding Access Conflicts on Target Buses The arbitration scheme allows only one master to be connected to a target at any given time. The following rules apply when prioritizing accesses from different masters to the same target bus: * CPU always has priority over BDM and XGATE. * XGATE access to PRU registers constitutes a special case. It is always granted and stalls the CPU for its duration. * XGATE has priority over BDM. * BDM has priority over CPU and XGATE when its access is stalled for more than 128 cycles. In the later case the suspect master will be stalled after finishing the current operation and the BDM will gain access to the bus. * In emulation modes all internal accesses are visible on the external bus as well and the external bus is used during access to the PRU registers. 18.4.5 Interrupts 18.4.5.1 Outgoing Interrupt Requests The following interrupt requests can be triggered by the MMC module: CPU access violation: The CPU access violation signals to the CPU detection of an error condition in the CPU application code which is resulted in write access to the protected XGATE RAM area (see Section 18.4.3.2, "Illegal CPU Accesses). 18.5 18.5.1 Initialization/Application Information CALL and RTC Instructions CALL and RTC instructions are uninterruptable CPU instructions that automate page switching in the program page window. The CALL instruction is similar to the JSR instruction, but the subroutine that is called can be located anywhere in the local address space or in any Flash or ROM page visible through the program page window. The CALL instruction calculates and stacks a return address, stacks the current PPAGE value and writes a new instruction-supplied value to the PPAGE register. The PPAGE value controls which of the 256 possible pages is visible through the 16 Kbyte program page window in the 64 Kbyte local CPU memory map. Execution then begins at the address of the called subroutine. During the execution of the CALL instruction, the CPU performs the following steps: 1. Writes the current PPAGE value into an internal temporary register and writes the new instruction-supplied PPAGE value into the PPAGE register 2. Calculates the address of the next instruction after the CALL instruction (the return address) and pushes this 16-bit value onto the stack 3. Pushes the temporarily stored PPAGE value onto the stack 4. Calculates the effective address of the subroutine, refills the queue and begins execution at the new address MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 683 Chapter 18 Memory Mapping Control (S12XMMCV3) This sequence is uninterruptable. There is no need to inhibit interrupts during the CALL instruction execution. A CALL instruction can be performed from any address to any other address in the local CPU memory space. The PPAGE value supplied by the instruction is part of the effective address of the CPU. For all addressing mode variations (except indexed-indirect modes) the new page value is provided by an immediate operand in the instruction. In indexed-indirect variations of the CALL instruction a pointer specifies memory locations where the new page value and the address of the called subroutine are stored. Using indirect addressing for both the new page value and the address within the page allows usage of values calculated at run time rather than immediate values that must be known at the time of assembly. The RTC instruction terminates subroutines invoked by a CALL instruction. The RTC instruction unstacks the PPAGE value and the return address and refills the queue. Execution resumes with the next instruction after the CALL instruction. During the execution of an RTC instruction the CPU performs the following steps: 1. Pulls the previously stored PPAGE value from the stack 2. Pulls the 16-bit return address from the stack and loads it into the PC 3. Writes the PPAGE value into the PPAGE register 4. Refills the queue and resumes execution at the return address This sequence is uninterruptable. The RTC can be executed from anywhere in the local CPU memory space. The CALL and RTC instructions behave like JSR and RTS instruction, they however require more execution cycles. Usage of JSR/RTS instructions is therefore recommended when possible and CALL/RTC instructions should only be used when needed. The JSR and RTS instructions can be used to access subroutines that are already present in the local CPU memory map (i.e. in the same page in the program memory page window for example). However calling a function located in a different page requires usage of the CALL instruction. The function must be terminated by the RTC instruction. Because the RTC instruction restores contents of the PPAGE register from the stack, functions terminated with the RTC instruction must be called using the CALL instruction even when the correct page is already present in the memory map. This is to make sure that the correct PPAGE value will be present on stack at the time of the RTC instruction execution. 18.5.2 Port Replacement Registers (PRRs) Registers used for emulation purposes must be rebuilt by the in-circuit emulator hardware to achieve full emulation of single chip mode operation. These registers are called port replacement registers (PRRs) (see Table 1-25). PRRs are accessible from CPU, BDM and XGATE using different access types (word aligned, word-misaligned and byte). Each access to PRRs will be extended to 2 bus cycles for write or read accesses independent of the operating mode. In emulation modes all write operations result in simultaneous writing to the internal registers (peripheral access) and to the emulated registers (external access) located in the PRU in the emulator. All read operations are performed from external registers (external access) in emulation modes. In all other modes the read operations are performed from the internal registers (peripheral access). MC9S12XDP512 Data Sheet, Rev. 2.21 684 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) Due to internal visibility of CPU accesses the CPU will be halted during XGATE or BDM access to any PRR. This rule applies also in normal modes to ensure that operation of the device is the same as in emulation modes. A summary of PRR accesses: * An aligned word access to a PRR will take 2 bus cycles. * A misaligned word access to a PRRs will take 4 cycles. If one of the two bytes accessed by the misaligned word access is not a PRR, the access will take only 3 cycles. * A byte access to a PRR will take 2 cycles. Table 18-23. PRR Listing PRR Name PRR Local Address PRR Location PORTA 0x0000 PIM PORTB 0x0001 PIM DDRA 0x0002 PIM DDRB 0x0003 PIM PORTC 0x0004 PIM PORTD 0x0005 PIM DDRC 0x0006 PIM DDRD 0x0007 PIM PORTE 0x0008 PIM DDRE 0x0009 PIM MMCCTL0 0x000A MMC MODE 0x000B MMC PUCR 0x000C PIM RDRIV 0x000D PIM EBICTL0 0x000E EBI EBICTL1 0x000F EBI Reserved 0x0012 MMC MMCCTL1 0x0013 MMC ECLKCTL 0x001C PIM Reserved 0x001D PIM PORTK 0x0032 PIM DDRK 0x0033 PIM MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 685 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.5.3 On-Chip ROM Control The MCU offers two modes to support emulation. In the first mode (called generator) the emulator provides the data instead of the internal FLASH and traces the CPU actions. In the other mode (called observer) the internal FLASH provides the data and all internal actions are made visible to the emulator. 18.5.3.1 ROM Control in Single-Chip Modes In single-chip modes the MCU has no external bus. All memory accesses and program fetches are internal (see Figure 18-27). No External Bus MCU Flash Figure 18-27. ROM in Single Chip Modes 18.5.3.2 ROM Control in Emulation Single-Chip Mode In emulation single-chip mode the external bus is connected to the emulator. If the EROMON bit is set, the internal FLASH provides the data and the emulator can observe all internal CPU actions on the external bus. If the EROMON bit is cleared, the emulator provides the data (generator) and traces the all CPU actions (see Figure 18-28). Observer Emulator MCU Flash EROMON = 1 Generator MCU Emulator Flash EROMON = 0 Figure 18-28. ROM in Emulation Single-Chip Mode MC9S12XDP512 Data Sheet, Rev. 2.21 686 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) 18.5.3.3 ROM Control in Normal Expanded Mode In normal expanded mode the external bus will be connected to the application. If the ROMON bit is set, the internal FLASH provides the data. If the ROMON bit is cleared, the application memory provides the data (see Figure 18-29). MCU Application Memory Flash ROMON = 1 MCU Application Memory ROMON = 0 Figure 18-29. ROM in Normal Expanded Mode MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 687 Chapter 18 Memory Mapping Control (S12XMMCV3) 18.5.3.4 ROM Control in Emulation Expanded Mode In emulation expanded mode the external bus will be connected to the emulator and to the application. If the ROMON bit is set, the internal FLASH provides the data. If the EROMON bit is set as well the emulator observes all CPU internal actions, otherwise the emulator provides the data and traces all CPU actions (see Figure 18-30). When the ROMON bit is cleared, the application memory provides the data and the emulator will observe the CPU internal actions (see Figure 18-31). Observer MCU Emulator Flash Application Memory EROMON = 1 Generator MCU Emulator Flash Application Memory EROMON = 0 Figure 18-30. ROMON = 1 in Emulation Expanded Mode MC9S12XDP512 Data Sheet, Rev. 2.21 688 Freescale Semiconductor Chapter 18 Memory Mapping Control (S12XMMCV3) Observer MCU Emulator Application Memory Figure 18-31. ROMON = 0 in Emulation Expanded Mode 18.5.3.5 ROM Control in Special Test Mode In special test mode the external bus is connected to the application. If the ROMON bit is set, the internal FLASH provides the data, otherwise the application memory provides the data (see Figure 18-32). Application MCU Memory ROMON = 0 Application MCU Flash Memory ROMON = 1 Figure 18-32. ROM in Special Test Mode MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 689 Chapter 18 Memory Mapping Control (S12XMMCV3) MC9S12XDP512 Data Sheet, Rev. 2.21 690 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.1 Introduction The DBG module provides an on-chip trace buffer with flexible triggering capability to allow non-intrusive debug of application software. The DBG module is optimized for the HCS12X 16-bit architecture and allows debugging of both CPU and XGATE module operations. Typically the DBG module is used in conjunction with the BDM module, whereby the user configures the DBG module for a debugging session over the BDM interface. Once configured the DBG module is armed and the device leaves BDM mode returning control to the user program, which is then monitored by the DBG module. Alternatively, the DBG module can be configured over a serial interface using SWI routines. Comparators monitor the bus activity of the CPU and XGATE modules. When a match occurs, the control logic can trigger the state sequencer to a new state or tag an opcode. A tag hit, which occurs when the tagged opcode reaches the execution stage of the instruction queue, can also cause a state transition. On a transition to the final state, bus tracing is triggered and/or a breakpoint can be generated. Independent of comparator matches, a transition to final state with associated tracing and breakpoint can be triggered by the external TAGHI and TAGLO signals. This is done by an XGATE module S/W breakpoint request or by writing to the TRIG control bit. The trace buffer is visible through a 2-byte window in the register address map and can be read out using standard 16-bit word reads. Tracing is disabled when the MCU system is secured. 19.1.1 Glossary of Terms COF: Change Of Flow. Change in the program flow due to a conditional branch, indexed jump or interrupt. BDM : Background Debug Mode DUG: Device User Guide, describing the features of the device into which the DBG is integrated. WORD: 16 bit data entity Data Line : 64 bit data entity XGATE : S12X family programmable Direct Memory Access Module CPU : S12X_CPU module Tag : Tags can be attached to XGATE or CPU opcodes as they enter the instruction pipe. If the tagged opcode reaches the execution stage a tag hit occurs. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 693 Chapter 19 S12X Debug (S12XDBGV2) Module 19.1.2 * * * * * * * Features Four comparators (A, B, C, and D): -- Comparators A and C compare the full address and the full 16-bit data bus -- Comparators A and C feature a data bus mask register -- Comparators B and D compare the full address bus only -- Each comparator can be configured to monitor either CPU or XGATE busses -- Each comparator features control of R/W and byte/word access cycles -- Comparisons can be used as triggers for the state sequencer Three comparator modes: -- Simple address/data comparator match mode -- Inside address range mode, Addmin Address Addmax -- Outside address range match mode, Address < Addmin or Address > Addmax Two types of triggers: -- Tagged: triggers just before a specific instruction begins execution -- Force: triggers on the first instruction boundary after a match occurs. Three types of breakpoints: -- CPU breakpoint entering BDM on breakpoint (BDM) -- CPU breakpoint executing SWI on breakpoint (SWI) -- XGATE breakpoint Three trigger modes independent of comparators: -- External instruction tagging (associated with CPU instructions only) -- XGATE S/W breakpoint request -- TRIG bit immediate software trigger Three trace modes: -- Normal: change of flow (COF) bus information is stored (see Section 19.4.5.2.1, "Normal Mode") for change of flow definition. -- Loop1: same as normal but inhibits consecutive duplicate source address entries -- Detail: address and data for all cycles except free cycles and opcode fetches are stored 4-stage state sequencer for trace buffer control: -- Tracing session trigger linked to final state of state sequencer -- Begin, end, and mid alignment of tracing to trigger 19.1.3 Modes of Operation The DBG module can be used in all MCU functional modes. During BDM hardware accesses and when the BDM module is active, CPU monitoring is disabled. Thus breakpoints, comparators and bus tracing mapped to the CPU are disabled but accessing the DBG registers, including comparator registers, is still possible. While in active BDM or during hardware BDM accesses, MC9S12XDP512 Data Sheet, Rev. 2.21 694 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module XGATE activity can still be compared, traced and can be used to generate a breakpoint to the XGATE module. When the CPU enters active BDM mode through a BACKGROUND command, with the DBG module armed, the DBG remains armed. The DBG module tracing is disabled if the MCU is secure. Breakpoints can however still be generated if the MCU is secure. Table 19-1. Mode Dependent Restriction Summary BDM Enable BDM Active MCU Secure Comparator Matches Enabled Breakpoints Possible Tagging Possible Tracing Possible x x 1 Yes Yes Yes No 0 0 0 Yes Only SWI Yes Yes 0 1 0 1 0 0 Yes Yes Yes Yes 1 1 0 XGATE only XGATE only XGATE only XGATE only 19.1.4 Active BDM not possible when not enabled Block Diagram Figure 19-1 shows a block diagram of the debug module. TAGS TAGHITS EXTERNAL TAGHI / TAGLO BREAKPOINT REQUESTS CPU & XGATE XGATE BUS COMPARATOR A COMPARATOR B COMPARATOR C COMPARATOR D COMPARATOR MATCH CONTROL CPU BUS BUS INTERFACE XGATE S/W BREAKPOINT REQUEST SECURE MATCH0 MATCH1 MATCH2 TRIGGER TAG & TRIGGER CONTROL LOGIC STATE STATE SEQUENCER MATCH3 TRACE CONTROL TRIGGER READ TRACE DATA (DBG READ DATA BUS) TRACE BUFFER Figure 19-1. Debug Block Diagram 19.2 External Signal Description The DBG sub-module features two external tag input signals (see Table 19-2). See Device User Guide (DUG) for the mapping of these signals to device pins. These tag pins may be used for the external tagging in emulation modes only MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 695 Chapter 19 S12X Debug (S12XDBGV2) Module . Table 19-2. External System Pins Associated With DBG Pin Name Pin Functions Description TAGHI (See DUG) TAGHI When instruction tagging is on, tags the high half of the instruction word being read into the instruction queue. TAGLO (See DUG) TAGLO When instruction tagging is on, tags the low half of the instruction word being read into the instruction queue. MC9S12XDP512 Data Sheet, Rev. 2.21 696 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.3 Memory Map and Register Definition A summary of the registers associated with the DBG sub-block is shown in Figure 19-2. Detailed descriptions of the registers and bits are given in the subsections that follow. 19.3.1 Register Descriptions This section consists of the DBG control and trace buffer register descriptions in address order. Each comparator has a bank of registers that are visible through an 8-byte window between 0x0028 and 0x002F in the DBG module register address map. When ARM is set in DBGC1, the only bits in the DBG module registers that can be written are ARM, TRIG and COMRV[1:0] Address Register Name 0x0020 DBGC1 Bit 7 R W 0x0021 DBGSR R ARM TBF 6 0 TRIG EXTF 5 4 XGSBPE BDM 0 0 3 2 1 DBGBRK 0 Bit 0 COMRV SSF2 SSF1 SSF0 W 0x0022 DBGTCR R W 0x0023 DBGC2 R TSOURCE TRANGE TRCMOD TALIGN CDCM ABCM 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 SC3 SC2 SC1 SC0 W 0x0024 DBGTBH R W 0x0025 DBGTBL R W 0x0026 DBGCNT R 0 CNT W 0x0027 DBGSCRX R 0 0 0 0 NDB TAG BRK RW RWE SRC COMPE SZ TAG BRK RW RWE SRC COMPE W 0x0028 0x0028 DBGXCTL1 (COMPA/C) DBGXCTL2 (COMPB/D) R 0 W R W SZE 1. This represents the contents if the comparator A or C control register is blended into this address 2. This represents the contents if the comparator B or D control register is blended into this address = Unimplemented or Reserved Figure 19-2. DBG Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 697 Chapter 19 S12X Debug (S12XDBGV2) Module Address Register Name 0x0029 DBGXAH Bit 7 6 5 4 3 2 1 Bit 0 Bit 22 21 20 19 18 17 Bit 16 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 R 0 W 0x002A DBGXAM R W 0x002B DBGXAL R W 0x002C DBGXDH R W 0x002D DBGXDL R W 0x002E DBGXDHM R W 0x002F DBGXDLM R W = Unimplemented or Reserved Figure 19-2. DBG Register Summary (continued) 19.3.1.1 Debug Control Register 1 (DBGC1) 0x0020 7 R W Reset 6 ARM 0 0 TRIG 0 5 4 XGSBPE BDM 0 0 3 2 1 DBGBRK 0 0 COMRV 0 0 0 Figure 19-3. Debug Control Register (DBGC1) Read: Anytime Write: Bits 7,1,0 anytime, Bit 6 can be written anytime but always reads back as 0. Bits 5:2 anytime DBG is not armed. NOTE When disarming the DBG by clearing ARM with software, the contents of bits[5:2] are not affected by the write, since up until the write operation, ARM=1 preventing these bits from being written. These bits must be cleared using a second write if required. MC9S12XDP512 Data Sheet, Rev. 2.21 698 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-3. DBGC1 Field Descriptions Field Description 7 ARM Arm Bit -- The ARM bit controls whether the DBG module is armed. This bit can be set and cleared by user software and is automatically cleared on completion of a tracing session, or if a breakpoint is generated with tracing not enabled. On setting this bit the state sequencer enters State1. When ARM is set, the only bits in the DBG module registers that can be written are ARM and TRIG. 0 Debugger disarmed 1 Debugger armed 6 TRIG Immediate Trigger Request Bit -- This bit when written to 1 requests an immediate trigger independent of comparator or external tag signal status. When tracing is complete a forced breakpoint may be generated depending upon DBGBRK and BDM bit settings. This bit always reads back a "0". Writing a "0" to this bit has no effect. If both TSOURCE bits are clear no tracing is carried out. If tracing has already commenced using BEGINor mid-trigger alignment, it continues until the end of the tracing session as defined by the TALIGN bit settings, thus TRIG has no affect. In secure mode tracing is disabled and writing to this bit has no effect. 0 Do not trigger until the state sequencer enters the final state. 1 Enter final state immediately and issue forced breakpoint request when trace buffer is full. 5 XGSBPE XGATE S/W Breakpoint Enable -- The XGSBPE bit controls whether an XGATE S/W breakpoint request is passed to the CPU. The XGATE S/W breakpoint request is handled by the DBG module, which can request an CPU breakpoint depending on the state of this bit. 0 XGATE S/W breakpoint request is disabled 1 XGATE S/W breakpoint request is enabled 4 BDM Background Debug Mode Enable -- This bit determines if a CPU breakpoint causes the system to enter background debug mode (BDM) or initiate a software interrupt (SWI). It has no affect on DBG functionality. This bit must be set if the BDM is enabled by the ENBDM bit in the BDM module to map breakpoints to BDM and must be cleared if the BDM module is disabled to map breakpoints to SWI. 0 Go to software interrupt on a breakpoint 1 Go to BDM on a breakpoint. 3-2 DBGBRK DBG Breakpoint Enable Bits -- The DBGBRK bits control whether the debugger will request a breakpoint to either CPU, XGATE or both upon reaching the state sequencer final state. If tracing is enabled, the breakpoint is generated on completion of the tracing session. If tracing is not enabled, the breakpoint is generated immediately. Please refer to Section 19.4.7, "Breakpoints" for further details. XGATE generated breakpoints are independent of the DBGBRK bits. XGATE generates a forced breakpoint to the CPU only. See Table 19-4. 1-0 COMRV Comparator Register Visibility Bits -- These bits determine which bank of comparator register is visible in the 8-byte window of the DBG module address map, located between 0x0028 to 0x002F. Furthermore these bits determine which state control register is visible at the address 0x0027. See Table 19-5. Table 19-4. DBGBRK Encoding DBGBRK Resource Halted by Breakpoint 00 No breakpoint generated 01 XGATE breakpoint generated 10 CPU breakpoint generated 11 Breakpoints generated for CPU and XGATE Table 19-5. COMRV Encoding COMRV Visible Comparator Visible State Control Register 00 Comparator A DBGSCR1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 699 Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-5. COMRV Encoding 19.3.1.2 COMRV Visible Comparator Visible State Control Register 01 Comparator B DBGSCR2 10 Comparator C DBGSCR3 11 Comparator D DBGSCR3 Debug Status Register (DBGSR) 0x0021 7 6 5 4 3 2 1 0 TBF EXTF 0 0 0 SSF2 SSF1 SSF0 Reset -- 0 0 0 0 0 0 0 POR 0 0 0 0 0 0 0 0 R W Unimplemented or Reserved Figure 19-4. Debug Status Register (DBGSR) Read: Anytime Write: Never Table 19-6. DBGSR Field Descriptions Field Description 7 TBF Trace Buffer Full -- The TBF bit indicates that the trace buffer has stored 64 or more lines of data since it was last armed. If this bit is set, then all 64 lines will be valid data, regardless of the value of DBGCNT bits CNT[6:0]. The TBF bit is cleared when ARM in DBGC1 is written to a 1. The TBF is cleared by the power on reset initialization. Other system generated resets have no affect on this bit 6 EXTF External Tag Hit Flag -- The EXTF bit indicates if a tag hit condition from an external TAGHI/TAGLO tag was met since arming. This bit is cleared when ARM in DBGC1 is written to a 1. 0 External tag hit has not occurred 1 External tag hit has occurred 2-0 SSF[2:0} State Sequencer Flag Bits -- The SSF bits indicate in which state the state sequencer is currently in. During a debug session on each transition to a new state these bits are updated. If the debug session is ended by software clearing the ARM bit, then these bits retain their value to reflect the last state of the state sequencer before disarming. If a debug session is ended by a breakpoint, then the state sequencer returns to state0 and these bits are cleared to indicate that state0 was entered during the session. On arming the module the state sequencer enters state1 and these bits are forced to SSF[2:0] = 001. See Table 19-7. Table 19-7. SSF[2:0] -- State Sequence Flag Bit Encoding SSF[2:0] Current State 000 State0 (disarmed) 001 State1 010 State2 011 State3 100 Final State 101,110,111 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 700 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.3.1.3 Debug Trace Control Register (DBGTCR) 0x0022 7 R 5 TSOURCE W Reset 6 0 4 3 TRANGE 0 0 2 1 TRCMOD 0 0 0 TALIGN 0 0 0 Figure 19-5. Debug Trace Control Register (DBGTCR) Read: Anytime Write: Bits 7:6 only when DBG is neither secure nor armed. Bits 5:0 anytime the module is disarmed. Table 19-8. DBGTCR Field Descriptions Field Description 7-6 TSOURCE Trace Source Control Bits -- The TSOURCE bits select the data source for the tracing session. If the MCU system is secured, these bits cannot be set and tracing is inhibited. See Table 19-9. 5-4 Trace Range Bits --The TRANGE bits allow filtering of trace information from a selected address range when TRANGE[5:4] tracing from the CPU in detail mode. The XGATE tracing range cannot be narrowed using these bits. To use a comparator for range filtering, the corresponding COMPE and SRC bits must remain cleared. If the COMPE bit is not clear then the comparator will also be used to generate state sequence triggers or tags. If the SRC bit is set the comparator is mapped to the XGATE busses, corrupting the trace. See Table 19-10. 3-2 Trace Mode Bits -- See Section 19.4.5.2, "Trace Modes" for detailed trace mode descriptions. In normal TRCMOD[3:2] mode, change of flow information is stored. In loop1 mode, change of flow information is stored but redundant entries into trace memory are inhibited. In detail mode, address and data for all memory and register accesses is stored. See Table 19-11 1-0 TALIGN[1:0] Trigger Align Bits -- These bits control whether the trigger is aligned to the beginning, end or the middle of a tracing session. See Table 19-12. Table 19-9. TSOURCE Trace Source Bit Encoding TSOURCE Tracing Source 00 No tracing requested 01 CPU 1 1 2 10 XGATE 111, 2 Both CPU and XGATE No range limitations are allowed. Thus tracing operates as if TRANGE = 00. No detail mode tracing supported. If TRCMOD =10, no information is stored. Table 19-10. TRANGE Trace Range Encoding TRANGE Tracing Source 00 Trace from all addresses (No filter) 01 Trace only in address range from 0x0000 to comparator D 10 Trace only in address range from comparator C to 0x7FFFFF MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 701 Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-10. TRANGE Trace Range Encoding TRANGE Tracing Source 11 Trace only in range from comparator C to comparator D Table 19-11. TRCMOD Trace Mode Bit Encoding TRCMOD Description 00 NORMAL 01 LOOP1 10 DETAIL 11 Reserved Table 19-12. TALIGN Trace Alignment Encoding 19.3.1.4 TALIGN Description 00 Trigger at end of stored data 01 Trigger before storing data 10 Trace buffer entries before and after trigger 11 Reserved Debug Control Register2 (DBGC2) 0x0023 R 7 6 5 4 0 0 0 0 0 0 0 0 3 1 CDCM W Reset 2 0 0 ABCM 0 0 0 Unimplemented or Reserved Figure 19-6. Debug Control Register2 (DBGC2) Read: Anytime Write: Anytime the module is disarmed. This register configures the comparators for range matching. Table 19-13. DBGC2 Field Descriptions Field Description 3-2 CDCM[3:2] C and D Comparator Match Control -- These bits determine the C and D comparator match mapping as described in Table 19-14. 1-0 ABCM[1:0] A and B Comparator Match Control -- These bits determine the A and B comparator match mapping as described in Table 19-15. MC9S12XDP512 Data Sheet, Rev. 2.21 702 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-14. CDCM Encoding CDCM Description 00 Match2 mapped to comparator C match....... Match3 mapped to comparator D match. 01 Match2 mapped to comparator C/D inside range....... Match3 disabled. 10 Match2 mapped to comparator C/D outside range....... Match3 disabled. 11 Reserved Table 19-15. ABCM Encoding 19.3.1.5 ABCM Description 00 Match0 mapped to comparator A match....... Match1 mapped to comparator B match. 01 Match 0 mapped to comparator A/B inside range....... Match1 disabled. 10 Match 0 mapped to comparator A/B outside range....... Match1 disabled. 11 Reserved Debug Trace Buffer Register (DBGTBH:DBGTBL) 0x0024 R W Reset 15 14 13 12 11 10 9 8 Bit 15 14 13 12 11 10 9 Bit 8 X X X X X X X X Figure 19-7. Debug Trace Buffer Register (DBGTBH) 0x0025 R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 X X X X X X X X Figure 19-8. Debug Trace Buffer Register (DBGTBL) Read: Anytime when unlocked and not secured and not armed. Write: Aligned word writes when disarmed unlock the trace buffer for reading but do not affect trace buffer contents Table 19-16. DBGTB Field Descriptions Field Description 15-0 Bit[15:0] Trace Buffer Data Bits -- The trace buffer register is a window through which the 64-bit wide data lines of the trace buffer may be read 16 bits at a time. Each valid read of DBGTB increments an internal trace buffer pointer which points to the next address to be read. When the ARM bit is written to 1 the trace buffer is locked to prevent reading. The trace buffer can only be unlocked for reading by writing to DBGTB with an aligned word write when the module is disarmed. The DBGTB register can be read only as an aligned word, any byte reads or misaligned access of these registers will return 0 and will not cause the trace buffer pointer to increment to the next trace buffer address. The same is true for word reads while the debugger is armed. System resets do not affect the trace buffer contents. The POR state is undefined. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 703 Chapter 19 S12X Debug (S12XDBGV2) Module 19.3.1.6 Debug Count Register (DBGCNT) 0x0026 7 R 6 5 4 0 3 2 1 0 CNT W Reset 0 POR 0 -- -- -- -- -- -- -- 0 0 0 0 0 0 0 Unimplemented or Reserved Figure 19-9. Debug Count Register (DBGCNT) Read: Anytime Write: Never Table 19-17. DBGCNT Field Descriptions Field Description 6-0 CNT[6:0] Count Value -- The CNT bits [6:0] indicate the number of valid data 64-bit data lines stored in the trace buffer. Table 19-18 shows the correlation between the CNT bits and the number of valid data lines in the trace buffer. When the CNT rolls over to 0, the TBF bit in DBGSR is set and incrementing of CNT will continue in end-trigger or mid-trigger mode. The DBGCNT register is cleared when ARM in DBGC1 is written to a 1. The DBGCNT register is cleared by power-on-reset initialization but is not cleared by other system resets. Thus should a reset occur during a debug session, the DBGCNT register still indicates after the reset, the number of valid trace buffer entries stored before the reset occurred. The DBGCNT register is not decremented when reading from the trace buffer. Table 19-18. CNT Decoding Table 1 TBF (DBGSR) CNT[6:0] Description 0 0000000 No data valid 0 0000001 32 bits of one line valid1 0 0000010 1 line valid 0 0000011 0000100 0000110 .. 1111100 1.5 lines valid1 2 lines valid 3 lines valid .. 62 lines valid 0 1111110 63 lines valid 1 0000000 64 lines valid; if using begin-trigger alignment, ARM bit will be cleared and the tracing session ends. 1 0000010 .. .. 1111110 64 lines valid, oldest data has been overwritten by most recent data This applies to normal/loop1 modes when tracing from either CPU or XGATE only. MC9S12XDP512 Data Sheet, Rev. 2.21 704 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.3.1.7 Debug State Control Registers Each of the state sequencer states 1 to 3 features a dedicated control register to determine if transitions from that state are allowed depending upon comparator matches or tag hits and to define the next state for the state sequencer following a match. The 3 debug state control registers are located at the same address in the register address map (0x0027). Each register can be accessed using the COMRV bits in DBGC1 to blend in the required register (see Table 19-19). Table 19-19. State Control Register Access Encoding 19.3.1.8 COMRV Visible State Control Register 00 DBGSCR1 01 DBGSCR2 10 DBGSCR3 11 DBGSCR3 Debug State Control Register 1 (DBGSCR1) 0x0027 R 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 SC3 SC2 SC1 SC0 0 0 0 0 Unimplemented or Reserved Figure 19-10. Debug State Control Register 1 (DBGSCR1) Read: Anytime Write: Anytime when DBG not armed. This register is visible at 0x0027 only with COMRV[1:0] = 00. The state control register 1 selects the targeted next state while in State1. The matches refer to the match channels of the comparator match control logic as depicted in Figure 19-1 and described in Section 19.3.1.11.1, "Debug Comparator Control Register (DBGXCTL)". Comparators must be enabled by setting the comparator enable bit in the associated DBGXCTL control register. Table 19-20. DBGSCR1 Field Descriptions Field 3-0 SC[3:0} Description State Control Bits -- These bits select the targeted next state while in State1, based upon the match event. See Table 19-21. The trigger priorities described in Table 19-38 dictate that in the case of simultaneous matches, the match on the lower channel number ([0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 705 Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-21. State1 Sequencer Next Sate Selection SC[3:0] Description 0000 Any match triggers to state2 0001 Any match triggers to state3 0010 Any match triggers to final state 0011 Match2 triggers to State2....... Other matches have no effect 0100 Match2 triggers to State3....... Other matches have no effect 0101 Match2 triggers to final state....... Other matches have no effect 0110 Match0 triggers to State2....... Match1 triggers to State3....... Other matches have no effect 0111 Match1 triggers to State3....... Match0 triggers final state....... Other matches have no effect 1000 Match0 triggers to State2....... Match2 triggers to State3....... Other matches have no effect 1001 Match2 triggers to State3....... Match0 triggers final state....... Other matches have no effect 1010 Match1 triggers to State2....... Match3 triggers to State3....... Other matches have no effect 1011 Match3 triggers to State3....... Match1 triggers to final state....... Other matches have no effect 1100 Reserved 1101 Reserved 1110 Reserved 1111 Reserved 19.3.1.9 Debug State Control Register 2 (DBGSCR2) 0x0027 R 7 6 5 4 0 0 0 0 0 0 0 W Reset 0 3 2 1 0 SC3 SC2 SC1 SC0 0 0 0 0 Unimplemented or Reserved Figure 19-11. Debug State Control Register 2 (DBGSCR2) Read: Anytime Write: Anytime when DBG not armed. This register is visible at 0x0027 only with COMRV[1:0] = 01. The state control register 2 selects the targeted next state while in State2. The matches refer to the match channels of the comparator match control logic as depicted in Figure 19-1 and described in Section 19.3.1.11.1, "Debug Comparator Control Register (DBGXCTL)". Comparators must be enabled by setting the comparator enable bit in the associated DBGXCTL control register. MC9S12XDP512 Data Sheet, Rev. 2.21 706 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-22. DBGSCR2 Field Descriptions Field 3-0 SC[3:0} Description State Control Bits -- These bits select the targeted next state while in State2, based upon the match event. See Table 19-23. The trigger priorities described in Table 19-38 dictate that in the case of simultaneous matches, the match on the lower channel number ([0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches. Table 19-23. State2 Sequencer Next State Selection SC[3:0] Description 0000 Any match triggers to state1 0001 Any match triggers to state3 0010 Any match triggers to final state 0011 Match3 triggers to State1....... Other matches have no effect 0100 Match3 triggers to State3....... Other matches have no effect 0101 Match3 triggers to final state....... Other matches have no effect 0110 Match0 triggers to State1....... Match1 triggers to State3....... Other matches have no effect 0111 Match1 triggers to State3....... Match0 triggers final state....... Other matches have no effect 1000 Match0 triggers to State1....... Match2 triggers to State3....... Other matches have no effect 1001 Match2 triggers to State3....... Match0 triggers final state....... Other matches have no effect 1010 Match1 triggers to State1....... Match3 triggers to State3....... Other matches have no effect 1011 Match3 triggers to State3....... Match1 triggers final state....... Other matches have no effect 1100 Reserved 1101 Reserved 1110 Reserved 1111 Reserved 19.3.1.10 Debug State Control Register 3 (DBGSCR3) 0x0027 R 7 6 5 4 0 0 0 0 0 0 0 0 W Reset 3 2 1 0 SC3 SC2 SC1 SC0 0 0 0 0 Unimplemented or Reserved Figure 19-12. Debug State Control Register 3 (DBGSCR3) Read: Anytime Write: Anytime when DBG not armed. This register is visible at 0x0027 only with COMRV[1]=1. The state control register 3 selects the targeted next state while in State3. The matches refer to the match channels of the comparator match control logic as depicted in Figure 19-1 and described in Section 19.3.1.11.1, "Debug Comparator Control Register MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 707 Chapter 19 S12X Debug (S12XDBGV2) Module (DBGXCTL)". Comparators must be enabled by setting the comparator enable bit in the associated DBGXCTL control register. Table 19-24. DBGSCR3 Field Descriptions Field Description 3-0 SC[3:0] State Control Bits -- These bits select the targeted next state while in State3, based upon the match event. The trigger priorities described in Table 19-38 dictate that in the case of simultaneous matches, the match on the lower channel number (0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches. Table 19-25. State3 Sequencer Next State Selection SC[3:0] Description 0000 Any match triggers to state1 0001 Any match triggers to state2 0010 Any match triggers to final state 0011 Match0 triggers to State1....... Other matches have no effect 0100 Match0 triggers to State2....... Other matches have no effect 0101 Match0 triggers to final state....... Other matches have no effect 0110 Match1 triggers to State1....... Other matches have no effect 0111 Match1 triggers to State2....... Other matches have no effect 1000 Match1 triggers to final state....... Other matches have no effect 1001 Match2 triggers to State2....... Match0 triggers to final state....... Other matches have no effect 1010 Match1 triggers to State1....... Match3 triggers to State2....... Other matches have no effect 1011 Match3 triggers to State2....... Match1 triggers to final state....... Other matches have no effect 1100 Match2 triggers to final state....... Other matches have no effect 1101 Match3 triggers to final state....... Other matches have no effect 1110 Reserved 1111 Reserved 19.3.1.11 Comparator Register Descriptions Each comparator has a bank of registers that are visible through an 8-byte window in the DBG module register address map. Comparators A and C consist of 8 register bytes (3 address bus compare registers, 2 data bus compare registers, 2 data bus mask registers and a control register). Comparators B and D consist of 4 register bytes (3 address bus compare registers and a control register). Each set of comparator registers is accessible in the same 8-byte window of the register address map and can be accessed using the COMRV bits in the DBGC1 register. If the Comparators B or D are accessed through the 8-byte window, then only the address and control bytes are visible, the 4 bytes associated with data bus and data bus masking read as 0 and cannot be written. Furthermore the control registers for comparators B and D differ from those of comparators A and C. Table 19-26. Comparator Register Layout 0x0028 CONTROL Read/Write MC9S12XDP512 Data Sheet, Rev. 2.21 708 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-26. Comparator Register Layout 0x0029 ADDRESS HIGH Read/Write 0x002A ADDRESS MEDIUM Read/Write 0x002B ADDRESS LOW Read/Write 0x002C DATA HIGH COMPARATOR Read/Write Comparator A and C only 0x002D DATA LOW COMPARATOR Read/Write Comparator A and C only 0x002E DATA HIGH MASK Read/Write Comparator A and C only 0x002F DATA LOW MASK Read/Write Comparator A and C only 19.3.1.11.1 Debug Comparator Control Register (DBGXCTL) The contents of this register bits 7 and 6 differ depending upon which comparator registers are visible in the 8-byte window of the DBG module register address map 0x0028 7 R 0 W Reset 0 6 5 4 3 2 1 0 NDB TAG BRK RW RWE SRC COMPE 0 0 0 0 0 0 0 Unimplemented or Reserved Figure 19-13. Debug Comparator Control Register (Comparators A and C) 0x0028 R W Reset 7 6 5 4 3 2 1 0 SZE SZ TAG BRK RW RWE SRC COMPE 0 0 0 0 0 0 0 0 Figure 19-14. Debug Comparator Control Register (Comparators B and D) Read: Anytime Write: Anytime when DBG not armed. Table 19-27. DBGXCTL Field Descriptions Field Description 7 Size Comparator Enable Bit -- The SZE bit controls whether access size comparison is enabled for the (COMPB/D) associated comparator. This bit is ignored if the TAG bit in the same register is set. SZE 0 Word/Byte access size is not used in comparison 1 Word/Byte access size is used in comparison 6 (COMPA/C) NDB Not Data Bus Compare -- The NDB bit controls whether the match occurs when the data bus matches the comparator register value or when the data bus differs from the register value. Furthermore database bits can be individually masked using the comparator data mask registers. This bit is only available for comparators A and C. This bit is ignored if the TAG bit in the same register is set. This bit position has an SZ functionality for comparators B and D. 0 Match on data bus equivalence to comparator register contents 1 Match on data bus difference to comparator register contents MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 709 Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-27. DBGXCTL Field Descriptions (continued) Field Description 6 Size Comparator Value Bit -- The SZ bit selects either word or byte access size in comparison for the (COMP B/D) associated comparator. This bit is ignored if the SZE bit is cleared or if the TAG bit in the same register is set. SZ This bit position has NDB functionality for comparators A and C 0 Word access size will be compared 1 Byte access size will be compared 5 TAG Tag Select -- This bit controls whether the comparator match will cause a trigger or tag the opcode at the matched address. Tagged opcodes trigger only if they reach the execution stage of the instruction queue. 0 Trigger immediately on match 1 On match, tag the opcode. If the opcode is about to be executed a trigger is generated 4 BRK Break -- This bit controls whether a comparator match can cause an immediate breakpoint independent of state sequencer state. The module breakpoints must be enabled using the DBGC1 bits DBGBRK[1:0]. 0 Breakpoints may only be generated from this channel when the state machine reaches final state. 1 A match on this channel generates an immediate breakpoint, tracing, if active, is terminated and the module disarmed. 3 RW Read/Write Comparator Value Bit -- The RW bit controls whether read or write is used in compare for the associated comparator. The RW bit is not used if RWE = 0. 0 Write cycle will be matched 1 Read cycle will be matched 2 RWE Read/Write Enable Bit -- The RWE bit controls whether read or write comparison is enabled for the associated comparator. This bit is not useful for tagged operations. 1 Read/Write is used in comparison 0 Read/Write is not used in comparison 1 SRC SRC -- Determines mapping of comparator to CPU or XGATE 0 The comparator is mapped to CPU busses 1 The comparator is mapped to XGATE address and data busses 0 COMPE Comparator Enable Bit-- Determines if comparator is enabled 0 The comparator is not enabled 1 The comparator is enabled for state sequence triggers or tag generation Table 19-28 shows the effect for RWE and RW on the comparison conditions. These bits are not useful for tagged operations since the trigger occurs based on the tagged opcode reaching the execution stage of the instruction queue. Thus, these bits are ignored if tagged triggering is selected. Table 19-28. Read or Write Comparison Logic Table RWE Bit RW Bit RW Signal Comment 0 x 0 RW not used in comparison 0 x 1 RW not used in comparison 1 0 0 Write data bus 1 0 1 No match 1 1 0 No match 1 1 1 Read data bus MC9S12XDP512 Data Sheet, Rev. 2.21 710 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.3.1.11.2 Debug Comparator Address High Register (DBGXAH) 0x0029 7 R 0 W Reset 0 6 5 4 3 2 1 0 Bit 22 21 20 19 18 17 Bit 16 0 0 0 0 0 0 0 Unimplemented or Reserved Figure 19-15. Debug Comparator Address High Register (DBGXAH) Read: Anytime Write: Anytime when DBG not armed. Table 19-29. DBGXAH Field Descriptions Field Description 6-0 Bits [22:16] Comparator Address High Compare Bits -- The comparator address high compare bits control whether the selected comparator will compare the address bus bits [22:16] to a logic 1 or logic 0. This register byte is ignored for XGATE compares. 0 Compare corresponding address bit to a logic 0 1 Compare corresponding address bit to a logic 1 19.3.1.11.3 Debug Comparator Address Mid Register (DBGXAM) 0x002A R W Reset 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Figure 19-16. Debug Comparator Address Mid Register (DBGXAM) Read: Anytime Write: Anytime when DBG not armed. Table 19-30. DBGXAM Field Descriptions Field 7-0 Bits [15:8] Description Comparator Address Mid Compare Bits -- The comparator address mid compare bits control whether the selected comparator will compare the address bus bits [15:8] to a logic 1 or logic 0. 0 Compare corresponding address bit to a logic 0 1 Compare corresponding address bit to a logic 1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 711 Chapter 19 S12X Debug (S12XDBGV2) Module 19.3.1.11.4 Debug Comparator Address Low Register (DBGXAL) 0x002B R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Figure 19-17. Debug Comparator Address Low Register (DBGXAL) Read: Anytime Write: Anytime when DBG not armed. Table 19-31. DBGXAL Field Descriptions Field 7-0 Bits [7:0] Description Comparator Address Low Compare Bits -- The comparator address low compare bits control whether the selected comparator will compare the address bus bits [7:0] to a logic 1 or logic 0. 0 Compare corresponding address bit to a logic 0 1 Compare corresponding address bit to a logic 1 19.3.1.11.5 Debug Comparator Data High Register (DBGXDH) 0x002C R W Reset 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Figure 19-18. Debug Comparator Data High Register (DBGXDH) Read: Anytime Write: Anytime when DBG not armed. Table 19-32. DBGXDH Field Descriptions Field Description 7-0 Bits [15:8] Comparator Data High Compare Bits -- The comparator data high compare bits control whether the selected comparator compares the data bus bits [15:8] to a logic 1 or logic 0. The comparator data compare bits are only used in comparison if the corresponding data mask bit is logic 1. This register is available only for comparators A and C. 0 Compare corresponding data bit to a logic 0 1 Compare corresponding data bit to a logic 1 MC9S12XDP512 Data Sheet, Rev. 2.21 712 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.3.1.11.6 Debug Comparator Data Low Register (DBGXDL) 0x002D R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Figure 19-19. Debug Comparator Data Low Register (DBGXDL) Read: Anytime Write: Anytime when DBG not armed. Table 19-33. DBGXDL Field Descriptions Field Description 7-0 Bits [7:0] Comparator Data Low Compare Bits -- The comparator data low compare bits control whether the selected comparator compares the data bus bits [7:0] to a logic 1 or logic 0. The comparator data compare bits are only used in comparison if the corresponding data mask bit is logic 1. This register is available only for comparators A and C. 0 Compare corresponding data bit to a logic 0 1 Compare corresponding data bit to a logic 1 19.3.1.11.7 Debug Comparator Data High Mask Register (DBGXDHM) 0x002E R W Reset 7 6 5 4 3 2 1 0 Bit 15 14 13 12 11 10 9 Bit 8 0 0 0 0 0 0 0 0 Figure 19-20. Debug Comparator Data High Mask Register (DBGXDHM) Read: Anytime Write: Anytime when DBG not armed. Table 19-34. DBGXDHM Field Descriptions Field Description 7-0 Bits [15:8] Comparator Data High Mask Bits -- The comparator data high mask bits control whether the selected comparator compares the data bus bits [15:8] to the corresponding comparator data compare bits. This register is available only for comparators A and C. 0 Do not compare corresponding data bit 1 Compare corresponding data bit MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 713 Chapter 19 S12X Debug (S12XDBGV2) Module 19.3.1.11.8 Debug Comparator Data Low Mask Register (DBGXDLM) 0x002F R W Reset 7 6 5 4 3 2 1 0 Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 Figure 19-21. Debug Comparator Data Low Mask Register (DBGXDLM) Read: Anytime Write: Anytime when DBG not armed. Table 19-35. DBGXDLM Field Descriptions Field Description 7-0 Bits [7:0] Comparator Data Low Mask Bits -- The comparator data low mask bits control whether the selected comparator compares the data bus bits [7:0] to the corresponding comparator data compare bits. This register is available only for comparators A and C. 0 Do not compare corresponding data bit 1 Compare corresponding data bit 19.4 Functional Description This section provides a complete functional description of the DBG module. If the part is in secure mode, the DBG module can generate breakpoints but tracing is not possible. 19.4.1 DBG Operation Arming the DBG module by setting ARM in DBGC1 allows triggering, and storing of data in the trace buffer and can be used to cause breakpoints to the CPU or the XGATE module. The DBG module is made up of 4 main blocks, the comparators, control logic, the state sequencer and the trace buffer. The comparators monitor the bus activity of the CPU and XGATE modules. Comparators can be configured to monitor address and databus. Comparators can also be configured to mask out individual data bus bits during a compare and to use R/W and word/byte access qualification in the comparison. When a match with a comparator register value occurs the associated control logic can trigger the state sequencer to another state (Figure 19-23). Either forced or tagged triggers are possible. Using a forced trigger, the trigger is generated immediately on a comparator match. Using a tagged trigger, at a comparator match, the instruction opcode is tagged and only if the instruction reaches the execution stage of the instruction queue is a trigger generated. In the case of a transition to final state, bus tracing is triggered and/or a breakpoint can be generated. Tracing of both CPU and/or XGATE bus activity is possible. Independent of the state sequencer, a breakpoint can be triggered by the external TAGHI / TAGLO signals, by an XGATE S/W breakpoint request or by writing to the TRIG bit in the DBGC1 control register. The trace buffer is visible through a 2-byte window in the register address map and can be read out using standard 16-bit word reads. MC9S12XDP512 Data Sheet, Rev. 2.21 714 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module TAGS TAGHITS EXTERNAL TAGHI / TAGLO BREAKPOINT REQUESTS CPU & XGATE XGATE BUS COMPARATOR A COMPARATOR B COMPARATOR C COMPARATOR D COMPARATOR MATCH CONTROL CPU BUS BUS INTERFACE XGATE S/W BREAKPOINT REQUEST SECURE MATCH0 MATCH1 MATCH2 TAG & TRIGGER TRIGGER CONTROL LOGIC STATE STATE SEQUENCER MATCH3 TRACE CONTROL TRIGGER READ TRACE DATA (DBG READ DATA BUS) TRACE BUFFER Figure 19-22. DBG Overview 19.4.2 Comparator Modes The DBG contains 4 comparators, A, B, C, and D. Each comparator can be configured to monitor either CPU or XGATE busses using the SRC bit in the corresponding comparator control register. Each comparator compares the selected address bus with the address stored in DBGXAH, DBGXAM and DBGXAL. Furthermore comparators A and C also compare the data buses to the data stored in DBGXDH, DBGXDL and allow masking of individual data bus bits. All comparators are disabled in BDM and during BDM accesses. The comparator match control logic (see Figure 19-22) configures comparators to monitor the busses for an exact address or an address range, whereby either an access inside or outside the specified range generates a match condition. The comparator configuration is controlled by the control register contents and the range control by the DBGC2 contents. On a match a trigger can initiate a transition to another state sequencer state (see Section 19.4.3, "Trigger Modes"). The comparator control register also allows the type of access to be included in the comparison through the use of the RWE,RW,SZE and SZ bits. The RWE bit controls whether read or write comparison is enabled for the associated comparator and the RW bit selects either a read or write access for a valid match. Similarly the SZE and SZ bits allows the size of access (word or byte) to be considered in the compare. Only comparators B and D feature SZE and SZ. The TAG bit in each comparator control register is used to determine the triggering condition. By setting TAG, the comparator will qualify a match with the output of opcode tracking logic and a trigger occurs before the tagged instruction executes (tagged-type trigger). Whilst tagging the RW, RWE, SZE and SZ bits are ignored and the comparator register must be loaded with the exact opcode address. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 715 Chapter 19 S12X Debug (S12XDBGV2) Module If the TAG bit is clear (forced type trigger) a comparator match is generated when the selected address appears on the system address bus. If the selected address is an opcode address, the match is generated when the opcode is fetched from the memory. This precedes the instruction execution by an indefinite number of cycles due to instruction pipe lining. For a comparator match of an opcode at an odd address when TAG = 0, the corresponding even address must be contained in the comparator register. Thus for an opcode at odd address (n), the comparator register must contain address (n - 1). Once a successful comparator match has occurred, the condition that caused the original match is not verified again on subsequent matches. Thus if a particular data value is verified at a given address, this address may not still contain that data value when a subsequent match occurs. Comparators C and D can also be used to select an address range to trace from. This is determined by the TRANGE bits in the DBGTCR register. The TRANGE encoding is shown in Table 19-10. If the TRANGE bits select a range definition using comparator D, then comparator D is configured for trace range definition and cannot be used for address bus comparisons. Similarly if the TRANGE bits select a range definition using comparator C, then comparator C is configured for trace range definition and cannot be used for address bus comparisons. Match[0,1,2,3] map directly to comparators [A,B,C,D] respectively, except in range modes (see Section 19.3.1.4, "Debug Control Register2 (DBGC2)"). Comparator priority rules are described in the trigger priority (see Section 19.4.3.6, "Trigger Priorities"). 19.4.2.1 Exact Address Comparator Match (Comparators A and C) With range comparisons disabled, the match condition is an exact equivalence of address/data bus with the value stored in the comparator address/data registers. Further qualification of the type of access (R/W, word/byte) is possible. Comparators A and C do not feature SZE or SZ control bits, thus the access size is not compared. The exact address is compared, thus with the comparator address register loaded with address (n) a misaligned word access of address (n-1) also accesses (n) but does not cause a match Table 19-37 lists access considerations without data bus compare. Table 19-36 lists access considerations with data bus comparison. To compare byte accesses DBGXDH must be loaded with the data byte. The low byte must be masked out using the DBGXDLM mask register. On word accesses data byte of the lower address is mapped to DBGXDH. Table 19-36. Comparator A and C Data Bus Considerations Access Address DBGxDH DBGxDL DBGxDHM DBGxDLM Example Valid Match Word ADDR[n] Data[n] Data[n+1] 0x_FF 0x_FF MOVW #$WORD ADDR[n] Byte ADDR[n] Data[n] x 0x_FF 0x_00 MOVB #$BYTE ADDR[n] Word ADDR[n] Data[n] x 0x_FF 0x_00 MOVW #$WORD ADDR[n] Word ADDR[n] x Data[n+1] 0x_00 0x_FF MOVW #$WORD ADDR[n] Comparators A and C feature an NDB control bit to determine if a match occurs when the data bus differs to comparator register contents or when the data bus is equivalent to the comparator register contents. MC9S12XDP512 Data Sheet, Rev. 2.21 716 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.2.2 Exact Address Comparator Match (Comparators B and D) Comparators B and D feature SZ and SZE control bits. If SZE is clear, then the comparator address match qualification functions the same as for comparators A and C. If the SZE bit is set the access size (word or byte) is compared with the SZ bit value such that only the specified type of access causes a match. Thus, if configured for a byte access of a particular address, a word access covering the same address does not lead to match. Table 19-37. Comparator Access Size Considerations 1 19.4.2.3 Comparator Address SZE SZ8 Condition For Valid Match Comparators A and C ADDR[n] - - Word and byte accesses of ADDR[n]1 MOVB #$BYTE ADDR[n] MOVW #$WORD ADDR[n] Comparators B and D ADDR[n] 0 X Word and byte accesses of ADDR[n]1 MOVB #$BYTE ADDR[n] MOVW #$WORD ADDR[n] Comparators B and D ADDR[n] 1 0 Word accesses of ADDR[n]1 MOVW #$WORD ADDR[n] Comparators B and D ADDR[n] 1 1 Byte accesses of ADDR[n] MOVB #$BYTE ADDR[n] A word access of ADDR[n-1] also accesses ADDR[n] but does not generate a match. The comparator address register must contain the exact address used in the code. Range Comparisons When using the AB comparator pair for a range comparison, the data bus can also be used for qualification by using the comparator A data and data mask registers. Furthermore the DBGACTL RW and RWE bits can be used to qualify the range comparison on either a read or a write access. The corresponding DBGBCTL bits are ignored. Similarly when using the CD comparator pair for a range comparison, the data bus can also be used for qualification by using the comparator C data and data mask registers. Furthermore the DBGCCTL RW and RWE bits can be used to qualify the range comparison on either a read or a write access if tagging is not selected. The corresponding DBGDCTL bits are ignored. The SZE and SZ control bits are ignored in range mode. The comparator A and C TAG bits are used to tag range comparisons for the AB and CD ranges respectively. The comparator B and D TAG bits are ignored in range modes. In order for a range comparison using comparators A and B, both COMPEA and COMPEB must be set; to disable range comparisons both must be cleared. Similarly for a range CD comparison, both COMPEC and COMPED must be set. If a range mode is selected SRCA and SRCB must select the same source (S12X or XGATE). Similarly SRCC and SRCD must select the same source. When configured for range comparisons and tagging, the ranges are accurate only to word boundaries. 19.4.2.3.1 Inside Range (CompAC_Addr Address CompBD_Addr) In the inside range comparator mode, either comparator pair A and B or comparator pair C and D can be configured for range comparisons. This configuration depends upon the control register (DBGC2). The match condition requires that a valid match for both comparators happens on the same bus cycle. A match condition on only one comparator is not valid. An aligned word access which straddles the range boundary will cause a trigger only if the aligned address is inside the range. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 717 Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.2.3.2 Outside Range (Address < CompAC_Addr or Address > CompBD_Addr) In the outside range comparator mode, either comparator pair A and B or comparator pair C and D can be configured for range comparisons. A single match condition on either of the comparators is recognized as valid. An aligned word access which straddles the range boundary will cause a trigger only if the aligned address is outside the range. Outside range mode in combination with tagged triggers can be used to detect if the opcode fetches are from an unexpected range. In forced trigger modes the outside range trigger would typically be activated at any interrupt vector fetch or register access. This can be avoided by setting the upper range limit to 0x7FFFFF or lower range limit to 0x000000 respectively. When comparing the XGATE address bus in outside range mode, the initial vector fetch as determined by the vector contained in the XGATE XGVBR register should be taken into consideration. The XGVBR register and hence vector address can be modified. 19.4.3 Trigger Modes Trigger modes are used as qualifiers for a state sequencer change of state. The control logic determines the trigger mode and provides a trigger to the state sequencer. The individual trigger modes are described in the following sections. 19.4.3.1 Trigger On Comparator Match If a comparator match occurs, a trigger occurs to initiate a transition to another state sequencer state and the corresponding flags in DBGSR are set. For a comparator match to trigger firstly the comparator must be enabled by setting the COMPE bit in the corresponding comparator control register. Secondly the state control register for the current state must enable the match for that state. The state control registers allow for different matches to be enabled in each of the states 1 to 3. 19.4.3.2 Trigger On Comparator Related Taghit If either a CPU or XGATE taghit occurs a transition to another state sequencer state is initiated and the corresponding DBGSR flags are set. For a comparator related taghit to occur, the DBG must first generate tags based on comparator matches. When the tagged instruction reaches the execution stage of the instruction queue a taghit is generated by the CPU/XGATE. 19.4.3.3 External Tag Trigger In external tagging trigger mode, the TAGLO and TAGHI pins (mapped to device pins) are used to tag an instruction. This function can be used as another breakpoint source. When the tagged opcode reaches the execution stage of the instruction queue a transition to the disarmed state0 occurs, ending the debug session and generating a breakpoint, if breakpoints are enabled. External tagging is only possible in device emulation modes. MC9S12XDP512 Data Sheet, Rev. 2.21 718 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.3.4 Trigger On XGATE S/W Breakpoint Request The XGATE S/W breakpoint request issues a forced breakpoint request to the CPU immediately independent of DBG settings. If the debug module is armed triggers the state sequencer into the disarmed state. Active tracing sessions are terminated immediately, thus if tracing has not yet begun using begintrigger, no trace information is stored. XGATE generated breakpoints are independent of the DBGBRK bits. The XGSBPE bit in DBGC1 determines if the XGATE S/W breakpoint function is enabled. The BDM bit in DBGC1 determines if the XGATE requested breakpoint causes the system to enter BDM mode or initiate a software interrupt (SWI). 19.4.3.5 Immediate Trigger At any time independent of comparator matches or external tag signals it is possible to initiate a tracing session and/or breakpoint by writing to the TRIG bit in DBGC1. This triggers the state sequencer into the final state and issues a forced breakpoint request to both CPU and XGATE. 19.4.3.6 Trigger Priorities In case of simultaneous triggers, the priority is resolved according to Table 19-38. The lower priority trigger is suppressed. It is thus possible to miss a lower priority trigger if it occurs simultaneously with a trigger of a higher priority. The trigger priorities described in Table 19-38 dictate that in the case of simultaneous matches, the match on the lower channel number ([0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches independent of current state sequencer state. When configured for range modes a simultaneous match of comparators A and C generates an active match0 while match2 is suppressed. Table 19-38. Trigger Priorities Priority Source Action Highest XGATE Immediate forced breakpoint......(Tracing terminated immediately). TRIG Enter final state Lowest External TAGHI/TAGLO Enter State0 Match0 (force or tag hit) Trigger to next state as defined by state control registers Match1 (force or tag hit) Trigger to next state as defined by state control registers Match2 (force or tag hit) Trigger to next state as defined by state control registers Match3 (force or tag hit) Trigger to next state as defined by state control registers MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 719 Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.4 State Sequence Control ARM = 0 State 0 (Disarmed) ARM = 1 State1 State2 ARM = 0 Session complete (disarm) Final State State3 ARM=0 Figure 19-23. State Sequencer Diagram The state sequence control allows a defined sequence of events to provide a trigger point for tracing of data in the trace buffer. Once the DBG module has been armed by setting the ARM bit in the DBGC1 register, then State1 of the state sequencer is entered. Further transitions between the states are then controlled by the state control registers and depend upon a selected trigger mode condition being met. From final state the only permitted transition is back to the disarmed state0. Transition between any of the states 1 to 3 is not restricted. Each transition updates the SSF[2:0] flags in DBGSR accordingly to indicate the current state. Alternatively writing to the TRIG bit in DBGSC1, the final state is entered and tracing starts immediately if the TSOURCE bits are configured for tracing. A tag hit through TAGHI/TAGLO causes a breakpoint, if breakpoints are enabled, and ends tracing immediately independent of the trigger alignment bits TALIGN[1:0]. Furthermore, each comparator channel can be individually configured to generate an immediate breakpoint when a match occurs through the use of the BRK bits in the DBGxCTL registers independent of the state sequencer state. Thus it is possible to generate an immediate breakpoint on selected channels, while a state sequencer transition can be initiated by a match on other channels. An XGATE S/W breakpoint request, if enabled causes a transition to the final state and generates a breakpoint request to the CPU immediately. If neither tracing nor breakpoints are enabled then, when a forced match triggers to final state, it can only be returned to the disarmed state0 by clearing the ARM bit by software. This also applies to the case that BDM breakpoints are enabled, but the BDM is disabled. Furthermore if neither tracing nor breakpoints are enabled, forced triggers on channels with BRK set cause a transition to the state determined by the state sequencer as if the BRK bit were not being used. If neither tracing nor breakpoints are enabled then when a tagged match triggers to final state, the state sequencer returns to the disarmed state0. MC9S12XDP512 Data Sheet, Rev. 2.21 720 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.4.1 Final State On entering final state a trigger may be issued to the trace buffer according to the trace position control as defined by the TALIGN field (see Section 19.3.1.3, "Debug Trace Control Register (DBGTCR)"). If the TSOURCE bits in the trace control register DBGTCR are cleared then the trace buffer is disabled and the transition to final state can only generate a breakpoint request. In this case or upon completion of a tracing session when tracing is enabled, the ARM bit in the DBGC1 register is cleared, returning the module to the disarmed state0. If tracing is enabled a breakpoint request can occur at the end of the tracing session. 19.4.5 Trace Buffer Operation The trace buffer is a 64 lines deep by 64-bits wide RAM array. The DBG module stores trace information in the RAM array in a circular buffer format. The CPU accesses the RAM array through a register window (DBGTBH:DBGTBL) using 16-bit wide word accesses. After each complete 64-bit trace buffer line is read via the CPU, an internal pointer into the RAM is incremented so that the next read will receive fresh information. Data is stored in the format shown in Table 19-39. After each store the counter register bits DBGCNT[6:0] are incremented. Tracing of CPU activity is disabled when the BDM is active but tracing of XGATE activity is still possible. Reading the trace buffer while the BDM is active returns invalid data and the trace buffer pointer is not incremented. 19.4.5.1 Trace Trigger Alignment Using the TALIGN bits (see Section 19.3.1.3, "Debug Trace Control Register (DBGTCR)") it is possible to align the trigger with the end, the middle or the beginning of a tracing session. If end or mid tracing is selected, tracing begins when the ARM bit in DBGC1 is set and State1 is entered. The transition to final state if end is selected signals the end of the tracing session. The transition to final state if mid is selected signals that another 32 lines will be traced before ending the tracing session. Tracing with begin-trigger starts at the opcode of the trigger. 19.4.5.1.1 Storing with Begin-Trigger Storing with begin-trigger, data is not stored in the trace buffer until the final state is entered. Once the trigger condition is met the DBG module will remain armed until 64 lines are stored in the trace buffer. If the trigger is at the address of the change-of-flow instruction the change of flow associated with the trigger will be stored in the trace buffer. Using begin-trigger together with tagging, if the tagged instruction is about to be executed then the trace is started. Upon completion of the tracing session the breakpoint is generated, thus the breakpoint does not occur at the tagged instruction boundary. 19.4.5.1.2 Storing with Mid-Trigger Storing with mid-trigger, data is stored in the trace buffer as soon as the DBG module is armed. When the trigger condition is met, another 32 lines will be traced before ending the tracing session, irrespective of the number of lines stored before the trigger occurred, then the DBG module is disarmed and no more data is stored. If the trigger is at the address of a change of flow instruction the trigger event is not stored in the trace buffer. Using mid-trigger with tagging, if the tagged instruction is about to be executed then the trace MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 721 Chapter 19 S12X Debug (S12XDBGV2) Module is continued for another 32 lines. Upon tracing completion the breakpoint is generated, thus the breakpoint does not occur at the tagged instruction boundary. 19.4.5.1.3 Storing with End-Trigger Storing with end-trigger, data is stored in the trace buffer until the final state is entered, at which point the DBG module will become disarmed and no more data will be stored. If the trigger is at the address of a change of flow instruction the trigger event will not be stored in the trace buffer. 19.4.5.2 Trace Modes The DBG module can operate in three trace modes. The mode is selected using the TRCMOD bits in the DBGTCR register. In each mode tracing of XGATE or CPU information is possible. The source for the trace is selected using the TSOURCE bits in the DBGTCR register. The modes are described in the following subsections. The trace buffer organization is shown in Table 19-39. 19.4.5.2.1 Normal Mode In normal mode, change of flow (COF) addresses will be stored. COF addresses are defined as follows for the CPU: * Source address of taken conditional branches (long, short, bit-conditional, and loop primitives) * Destination address of indexed JMP, JSR and CALL instruction. * Destination address of RTI, RTS and RTC instructions * Vector address of interrupts, except for SWI and BDM vectors LBRA, BRA, BSR, BGND as well as non-indexed JMP, JSR, and CALL instructions are not classified as change of flow and are not stored in the trace buffer. COF addresses are defined as follows for the XGATE: * Source address of taken conditional branches * Destination address of indexed JAL instructions. * First XGATE code address, determined by the vector contained in the XGATE XGVBR register Change-of-flow addresses stored include the full 23-bit address bus in the case of CPU, the 16-bit address bus for the XGATE module and an information byte, which contains a source/destination bit to indicate whether the stored address was a source address or destination address. 19.4.5.2.2 Loop1 Mode Loop1 mode, similarly to normal mode also stores only COF address information to the trace buffer, it however allows the filtering out of redundant information. The intent of loop1 mode is to prevent the trace buffer from being filled entirely with duplicate information from a looping construct such as delays using the DBNE instruction or polling loops using BRSET/BRCLR instructions. Immediately after address information is placed in the trace buffer, the DBG module writes this value into a background register. This prevents consecutive duplicate address entries in the trace buffer resulting from repeated branches. MC9S12XDP512 Data Sheet, Rev. 2.21 722 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module Loop1 mode only inhibits consecutive duplicate source address entries that would typically be stored in most tight looping constructs. It does not inhibit repeated entries of destination addresses or vector addresses, since repeated entries of these would most likely indicate a bug in the user's code that the DBG module is designed to help find. NOTE In certain very tight loops, the source address will have already been fetched again before the background comparator is updated. This results in the source address being stored twice before further duplicate entries are suppressed. This condition occurs with branch-on-bit instructions when the branch is fetched by the first P-cycle of the branch or with loop-construct instructions in which the branch is fetched with the first or second P cycle. See examples below: LOOP LOOP2 INX BRCLR BRN* NOP DBNE 19.4.5.2.3 CMPTMP,#$0c,LOOP A,LOOP2 ;1-byte instruction fetched by 1st P-cycle of BRCLR ;the BRCLR instruction also will be fetched by 1st P-cycle ;of BRCLR ; 2-byte instruction fetched by 1st P-cycle of DBNE ; 1-byte instruction fetched by 2nd P-cycle of DBNE ; this instruction also fetched by 2nd P-cycle of DBNE Detail Mode In detail mode, address and data for all memory and register accesses is stored in the trace buffer. In the case of XGATE tracing this means that initialization of the R1 register during a vector fetch is not traced. This mode is intended to supply additional information on indexed, indirect addressing modes where storing only the destination address would not provide all information required for a user to determine where the code is in error. This mode also features information byte storage to the trace buffer, for each address byte storage. The information byte indicates the size of access (word or byte), the type of access (read or write). When tracing CPU activity in detail mode, all cycles are traced except those when the CPU is either in a free or opcode fetch cycle. In this mode the XGATE program counter is also traced to provide a snapshot of the XGATE activity. CXINF information byte bits indicate the type of XGATE activity occurring at the time of the trace buffer entry. When tracing CPU activity alone in detail mode, the address range can be limited to a range specified by the TRANGE bits in DBGTCR. This function uses comparators C and D to define an address range inside which CPU activity should be traced (see Table 19-10). Thus, the traced CPU activity can be restricted to register range accesses. When tracing XGATE activity in detail mode, all cycles apart from opcode fetch and free cycles are stored to the trace buffer. Additionally the CPU program counter is stored at the time of the XGATE trace buffer entry to provide a snapshot of CPU activity. 19.4.5.3 Trace Buffer Organization The buffer can be used to trace either from CPU, from XGATE or from both sources. An "X" prefix denotes information from the XGATE module, a "C" prefix denotes information from the CPU. ADRH,ADRM,ADRL denote address high, middle and low byte respectively. INF bytes contain control MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 723 Chapter 19 S12X Debug (S12XDBGV2) Module information (R/W, S/D etc.). The numerical suffix indicates which tracing step. The information format for loop1 mode is the same as that of normal mode. Whilst tracing from XGATE or CPU only, in normal or loop1 modes each array line contains data from entries made at 2 separate times, thus in this case the DBGCNT[0] is incremented after each separate entry. In all other modes, DBGCNT[0] remains cleared while the other DBGCNT bits are incremented on each trace buffer entry. XGATE and S12X_CPU COFs occur independently of each other and the profile of COFs for the 2 sources is totally different. When both sources are being traced in Normal or Loop1 mode, for each single entry from one source, there may be many entries from the other source and vice versa, depending on user code. COF events could occur far from each other in the time domain, on consecutive cycles or simultaneously. If a COF occurs in one source only in a particular cycle, then the trace buffer bytes that are mapped to the other source are redundant. Info byte bit CDV/XDV indicates that no useful information is stored in these bytes. This is the typical case. Only in the rare event that both XGATE and S12X_CPU COF cycles coincide is a valid trace buffer entry for both made, corresponding to the first line for mode "Both Normal/Loop1" in Table 19-39. Single byte data accesses in detail mode are always stored to the low byte of the trace buffer (CDATAL or XDATAL) and the high byte is cleared. When tracing word accesses, the byte at the lower address is always stored to trace buffer byte3 and the byte at the higher address is stored to byte2 Table 19-39. Trace Buffer Organization 8-Byte Wide Word Buffer Mode XGATE DETAIL CPU DETAIL Both NORMAL / LOOP1 1 2 7 6 5 4 3 2 1 0 CXINF1 CADRH1 CADRM1 CADRL1 XDATAH1 XDATAL1 XADRM1 XADRL1 CXINF2 CADRH2 CADRM2 CADRL2 XDATAH2 XDATAL2 XADRM2 XADRL2 CXINF1 CADRH1 CADRM1 CADRL1 CDATAH1 CDATAL1 XADRM1 XADRL1 CXINF2 CADRH2 CADRM2 CADRL2 CDATAH2 CDATAL2 XADRM2 XADRL2 XADRM0 XADRL0 CINF0 CADRH0 CADRM0 CADRL0 CINF1 CADRH1 CADRM1 CADRL1 XINF0 1 XINF1 2 XINF2 XADRM2 XADRL2 CINF2 XGATE NORMAL / LOOP1 XINF1 XADRM1 XADRL1 XINF0 XADRM0 XADRL0 XINF3 XADRM3 XADRL3 XINF2 XADRM2 XADRL2 CPU NORMAL / LOOP1 CINF1 CADRH1 CADRM1 CADRL1 CINF0 CADRH0 CADRM0 CADRL0 CINF3 CADRH3 CADRM3 CADRL3 CINF2 CADRH2 CADRM2 CADRL2 COF in CPU only. XGATE trace buffer entries in this tracing step are invalid COF in XGATE only. CPU trace buffer entries in this tracing step are invalid MC9S12XDP512 Data Sheet, Rev. 2.21 724 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.5.3.1 Information Byte Organization The format of the control information byte for both CPU and XGATE modules is dependent upon the active trace mode and tracing source as described below. In normal mode or loop1 mode, tracing of XGATE activity XINF is used to store control information. In normal mode or loop1 mode, tracing of CPU activity CINF is used to store control information. In detail mode, CXINF contains the control information. Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 XSD 0 0 XDV 0 0 0 0 Figure 19-24. XGATE Information Byte XINF Table 19-40. XINF Field Descriptions Field Description 7 XSD Source Destination Indicator -- This bit indicates if the corresponding stored address is a source or destination address. This is only used in normal and loop1 mode tracing. 0 Source Address 1 Destination Address 4 XDV Data Invalid Indicator -- This bit indicates if the trace buffer entry is invalid. It is only used when tracing from both sources in normal and loop1 mode, to indicate that the XGATE trace buffer entry is valid. 0 Trace buffer entry is invalid 1 Trace buffer entry is valid Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CSD 0 0 CDV 0 0 0 0 Figure 19-25. CPU Information Byte CINF Table 19-41. CINF Field Descriptions Field Description 7 CSD Source Destination Indicator -- This bit indicates if the corresponding stored address is a source or destination address. This is only used in normal and loop1 mode tracing. 0 Source Address 1 Destination Address 4 CDV Data Invalid Indicator -- This bit indicates if the trace buffer entry is invalid. It is only used when tracing from both sources in normal and loop1 mode, to indicate that the CPU trace buffer entry is valid. 0 Trace buffer entry is invalid 1 Trace buffer entry is valid MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 725 Chapter 19 S12X Debug (S12XDBGV2) Module Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CFREE CSZ CRW COCF XACK XSZ XRW XOCF Figure 19-26. Information Byte CXINF This describes the format of the information byte used only when tracing from CPU or XGATE in detail mode. When tracing from the CPU in detail mode, information is stored to the trace buffer on all cycles except opcode fetch and free cycles. The XGATE entry stored on the same line is a snapshot of the XGATE program counter. In this case the CSZ and CRW bits indicate the type of access being made by the CPU, while the XACK and XOCF bits indicate if the simultaneous XGATE cycle is a free cycle (no bus acknowledge) or opcode fetch cycle. Similarly when tracing from the XGATE in detail mode, information is stored to the trace buffer on all cycles except opcode fetch and free cycles. The CPU entry stored on the same line is a snapshot of the CPU program counter. In this case the XSZ and XRW bits indicate the type of access being made by the XGATE, while the CFREE and COCF bits indicate if the simultaneous CPU cycle is a free cycle or opcode fetch cycle. Table 19-42. CXINF Field Descriptions Field Description 7 CREE CPU Free Cycle Indicator -- This bit indicates if the stored CPU address corresponds to a free cycle. This bit only contains valid information when tracing the XGATE accesses in detail mode. 0 Stored information corresponds to free cycle 1 Stored information does not correspond to free cycle 6 CSZ Access Type Indicator -- This bit indicates if the access was a byte or word size access.This bit only contains valid information when tracing CPU activity in detail mode. 0 Word Access 1 Byte Access 5 CRW Read Write Indicator -- This bit indicates if the corresponding stored address corresponds to a read or write access. This bit only contains valid information when tracing CPU activity in detail mode. 0 Write Access 1 Read Access 4 COCF CPU Opcode Fetch Indicator -- This bit indicates if the stored address corresponds to an opcode fetch cycle. This bit only contains valid information when tracing the XGATE accesses in detail mode. 0 Stored information does not correspond to opcode fetch cycle 1 Stored information corresponds to opcode fetch cycle 3 XACK XGATE Access Indicator -- This bit indicates if the stored XGATE address corresponds to a free cycle. This bit only contains valid information when tracing the CPU accesses in detail mode. 0 Stored information corresponds to free cycle 1 Stored information does not correspond to free cycle 2 XSZ Access Type Indicator -- This bit indicates if the access was a byte or word size access. This bit only contains valid information when tracing XGATE activity in detail mode. 0 Word Access 1 Byte Access MC9S12XDP512 Data Sheet, Rev. 2.21 726 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module Table 19-42. CXINF Field Descriptions (continued) Field Description 1 XRW Read Write Indicator -- This bit indicates if the corresponding stored address corresponds to a read or write access. This bit only contains valid information when tracing XGATE activity in detail mode. 0 Read/Write Access 1 Access 0 XOCF XGATE Opcode Fetch Indicator -- This bit indicates if the stored address corresponds to an opcode fetch cycle.This bit only contains valid information when tracing the CPU accesses in detail mode. 0 Stored information does not correspond to opcode fetch cycle 1 Stored information corresponds to opcode fetch cycle 19.4.5.3.2 Reading Data from Trace Buffer The data stored in the trace buffer can be read using either the background debug module (BDM) module or the CPU provided the DBG module is not armed, is configured for tracing (at least one TSOURCE bit is set) and the system not secured. When the ARM bit is written to 1 the trace buffer is locked to prevent reading. The trace buffer can only be unlocked for reading by a single aligned word write to DBGTB when the module is disarmed. Multiple writes to the DBGTB are not allowed since they increment the pointer. The trace buffer can only be read through the DBGTB register using aligned word reads, any byte or misaligned reads return 0 and do not cause the trace buffer pointer to increment to the next trace buffer address. The trace buffer data is read out first-in first-out. By reading CNT in DBGCNT the number of valid 64-bit lines can be determined. DBGCNT will not decrement as data is read. Whilst reading an internal pointer is used to determine the next line to be read. After a tracing session, the pointer points to the oldest data entry, thus if no overflow has occurred, the pointer points to line0, otherwise it points to the line with the oldest entry. The pointer is initialized by each aligned write to DBGTBH to point to the oldest data again. This enables an interrupted trace buffer read sequence to be easily restarted from the oldest data entry. The least significant word of each 64-bit wide array line is read out first. This corresponds to the bytes 1 and 0 of Table 19-39. The bytes containing invalid information (shaded in Table 19-39) are also read out. Reading the trace buffer while the DBG module is armed will return invalid data and no shifting of the RAM pointer will occur. Reading the trace buffer is not possible if both TSOURCE bits are cleared. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 727 Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.5.3.3 Trace Buffer Reset State The trace buffer contents are not initialized by a system reset. Thus should a system reset occur, the trace session information from immediately before the reset occurred can be read out. The DBGCNT bits are not cleared by a system reset. Thus should a reset occur, the number of valid lines in the trace buffer is indicated by DBGCNT. The internal pointer to the current trace buffer address is initialized by unlocking the trace buffer thus points to the oldest valid data even if a reset occurred during the tracing session. Generally debugging occurrences of system resets is best handled using mid or end-trigger alignment since the reset may occur before the trace trigger, which in the begin-trigger alignment case means no information would be stored in the trace buffer. 19.4.6 Tagging A tag follows program information as it advances through the instruction queue. When a tagged instruction reaches the head of the queue a tag hit occurs and triggers the state sequencer. Each comparator control register features a TAG bit, which controls whether the comparator match will cause a trigger immediately or tag the opcode at the matched address. If a comparator is enabled for tagged comparisons, the address stored in the comparator match address registers must be an opcode address for the trigger to occur. Both CPU and XGATE opcodes can be tagged with the comparator register TAG bits. Using a begin-aligned trigger together with tagging, if the tagged instruction is about to be executed then the transition to the next state sequencer state occurs. If the transition is to the final state, tracing is started. Only upon completion of the tracing session can a breakpoint be generated. Similarly using a mid-aligned trigger with tagging, if the tagged instruction is about to be executed then the trace is continued for another 32 lines. Upon tracing completion the breakpoint is generated. Using an end-aligned trigger, when the tagged instruction is about to be executed and the next transition is to final state then a breakpoint is generated immediately, before the tagged instruction is carried out. R/W monitoring is not useful for tagged operations since the trigger occurs based on the tagged opcode reaching the execution stage of the instruction queue. Similarly access size (SZ) monitoring and data bus monitoring is not useful if tagged triggering is selected, since the tag is attached to the opcode at the matched address and is not dependent on the data bus nor on the size of access. Thus these bits are ignored if tagged triggering is selected. When configured for range comparisons and tagging, the ranges are accurate only to word boundaries. CPU tagging is disabled when the BDM becomes active. Conversely, BDM firmware commands are not processed while tagging is active. XGATE tagging is possible when the BDM is active. MC9S12XDP512 Data Sheet, Rev. 2.21 728 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.6.1 External Tagging using TAGHI and TAGLO External tagging using the external TAGHI and TAGLO pins can only be used to tag CPU opcodes; tagging of XGATE code using these pins is not possible. An external tag triggers the state sequencer into State0 when the tagged opcode reaches the execution stage of the instruction queue. The pins operate independently, thus the state of one pin does not affect the function of the other. External tagging is possible in emulation modes only. The presence of logic level 0 on either pin at the rising edge of the external clock (ECLK) performs the function indicated in the Table 19-43. It is possible to tag both bytes of an instruction word. If a taghit comes from the low or high byte, a breakpoint generated according to the DBGBRK and BDM bits in DBGC1. Each time TAGHI or TAGLO are low on the rising edge of ECLK, the old tag is replaced by a new one Table 19-43. Tag Pin Function 19.4.7 TAGHI TAGLO Tag 1 1 No tag 1 0 Low byte 0 1 High byte 0 0 Both bytes Breakpoints It is possible to select breakpoints to the XGATE and let the CPU continue operation, setting DBGBRK[0], or breakpoints to the CPU and let the XGATE continue operation setting, DBGBRK[1], or a breakpoint to both CPU and XGATE, setting both bits DBGBRK[1:0]. There are several ways to generate breakpoints to the XGATE and CPU modules. * Through XGATE software breakpoint requests. * From comparator channel triggers to final state. * Using software to write to the TRIG bit in the DBGC1 register. * From taghits generated using the external TAGHI and TAGLO pins. 19.4.7.1 XGATE Software Breakpoints The XGATE software breakpoint instruction BRK can request an CPU breakpoint, via the DBG module. In this case, if the XGSBPE bit is set, the DBG module immediately generates a forced breakpoint request to the CPU, the state sequencer is returned to state0 and tracing, if active, is terminated. If configured for begin-trigger and tracing has not yet been triggered from another source, the trace buffer contains no new information. Breakpoint requests from the XGATE module do not depend upon the state of the DBGBRK or ARM bits in DBGC1. They depend solely on the state of the XGSBPE and BDM bits. Thus it is not necessary to ARM the DBG module to use XGATE software breakpoints to generate breakpoints in the CPU program flow, but it is necessary to set XGSBPE. Furthermore if a breakpoint to BDM is required, the BDM bit must also be set. When the XGATE requests an CPU breakpoint, the XGATE program flow stops by default, independent of the DBG module. The user can thus determine if an XGATE breakpoint has occurred by reading out the XGATE program counter over the BDM interface. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 729 Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.7.2 Breakpoints From Internal Comparator Channel Final State Triggers Breakpoints can be generated when internal comparator channels trigger the state sequencer to the final state. If configured for tagging, then the breakpoint is generated when the tagged opcode reaches the execution stage of the instruction queue. If an end aligned trigger is selected or no tracing is enabled, breakpoints can be generated immediately, depending on the state of the DBGBRK[n] bits. If a begin or mid aligned tracing session is selected by the TSOURCE bits, breakpoints are requested when the tracing session has completed, thus the breakpoint is requested only on completion of the subsequent trace (see Table 19-44). If the BRK bit is set on the triggering channel, then the breakpoint is generated immediately independent of tracing trigger alignment. Table 19-44. Setup for Both XGATE and CPU Breakpoints BRK TALIGN DBGBRK[n] Type of Debug Session 0 00 0 Fill trace buffer until trigger (no breakpoints -- keep running) 0 00 1 Fill trace buffer until trigger, then a breakpoint request occurs 0 01 0 Start trace buffer at trigger (no breakpoints -- keep running) 0 01 1 Start trace buffer at trigger A breakpoint request occurs when trace buffer is full 0 10 0 Start trace buffer at trigger End tracing 32 line entries after trigger (no breakpoints -- keep running) 0 10 1 Start trace buffer at trigger End tracing 32 line entries after trigger Request breakpoint after the 32 further trace buffer entries 1 00,01,10 0 Terminate tracing immediately on trigger without breakpoint 1 00,01,10 1 Terminate tracing and generate breakpoint immediately on trigger x 11 x Reserved 19.4.7.3 Breakpoints Generated Via The TRIG Bit If a TRIG triggers occur, the final state is entered. Tracing trigger alignment is defined by the TALIGN bits. If a tracing session is selected by the TSOURCE bits, breakpoints are requested when the tracing session has completed, thus if begin or mid aligned triggering is selected, the breakpoint is requested only on completion of the subsequent trace. If no tracing session is selected, breakpoints are requested immediately. TRIG breakpoints are possible even if the DBG module is disarmed. TRIG bit breakpoints are enabled by setting DBGBRK[n]. 19.4.7.4 Breakpoints via TAGHI Or TAGLO Pin Taghits Tagging using the external TAGHI/TAGLO pins always ends the session immediately at the tag hit. It is always end aligned, independent of internal channel trigger alignment configuration. External tag breakpoints are always mapped to the CPU, are only possible in emulation modes and can be enabled by setting DBGBRK[1]. MC9S12XDP512 Data Sheet, Rev. 2.21 730 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module 19.4.7.5 DBG Breakpoint Priorities XGATE software breakpoints have the highest priority. Active tracing sessions are terminated immediately. If a TRIG triggers occur after begin or mid aligned tracing has already been triggered by a comparator instigated transition to final state, then TRIG no longer has an effect. When the associated tracing session is complete, the breakpoint occurs. Similarly if a TRIG is followed by a subsequent trigger from a comparator channel whose BRK=0, it has no effect, since tracing has already started. If a comparator tag hit occurs simultaneously with an external TAGHI/TAGLO hit, the state sequencer enters State0. TAGHI/TAGLO triggers are always end aligned, to end tracing immediately, independent of the tracing trigger alignment bits TALIGN[1:0]. 19.4.7.5.1 DBG Breakpoint priorities, mapping and BDM interfacing Breakpoint operation is dependent on the state of the BDM module. If the BDM module is active, the CPU is executing out of BDM firmware and S12X breakpoints are disabled. In addition, while executing a BDM TRACE command, tagging into BDM is disabled. Table 19-45. Breakpoint Mapping Summary DBGBRK[1] BDM bit (DBGC1[3])1 (DBGC1[4]) BDM enabled BDM active Type of Debug Session 0 X X X No Breakpoint 1 0 0 0 Breakpoint to SWI 1 0 1 X Illegal Configuration. Do Not Use.2 1 1 0 0 Illegal Configuration. Do Not Use. 3 1 1 1 0 Breakpoint to BDM 1 1 1 1 No Breakpoint 1 2 All sources except XGATE software BKP, which are independent of this bit. The DBGC1[4] bit (BDM) must be set if using the BDM interface together with the DBG module. Failure to set this bit could result in XGATE generated breakpoints to SWI during BDM firmware execution corrupting the S12X PC return address, should the user have entered BDM via the BACKGROUND command or BGND instruction. 3 End aligned tagged Breakpoint to SWI. Begin, Mid aligned and Forced Breakpoints disabled If BDM is not active, the breakpoint will give priority to BDM requests over SWI requests if the breakpoint happens to coincide with a SWI instruction in the user's code. On returning from BDM, the SWI from user code gets executed. BDM cannot be entered from a breakpoint unless the ENABLE bit is set in the BDM. If entry to BDM via a BGND instruction is attempted and the ENABLE bit in the BDM is cleared, the CPU actually executes the BDM firmware code. It checks the ENABLE and returns if ENABLE is not set. If not serviced by the monitor then the breakpoint is re-asserted when the BDM returns to normal CPU flow. If the comparator register contents coincide with the SWI/BDM vector address then an SWI in user code and DBG breakpoint could occur simultaneously. The CPU ensures that BDM requests have a higher priority than SWI requests. Returning from the BDM/SWI service routine care must be taken to avoid re-triggering a breakpoint. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 731 Chapter 19 S12X Debug (S12XDBGV2) Module When program control returns from a tagged breakpoint using an RTI or BDM GO command without program counter modification it will return to the instruction whose tag generated the breakpoint. Thus care must be taken to avoid re triggering a breakpoint at the same location. This can be done by reconfiguring the DBG module in the SWI routine, (SWI configuration), or by executing a TRACE command before the GO (BDM configuration) to increment the program flow past the tagged instruction. Comparators should not be configured for the vector address range while tagging, since these addresses are not opcode addresses MC9S12XDP512 Data Sheet, Rev. 2.21 732 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 733 Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 734 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 735 Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 736 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 737 Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 738 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 739 Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 740 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 741 Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 742 Freescale Semiconductor Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 743 Chapter 19 S12X Debug (S12XDBGV2) Module MC9S12XDP512 Data Sheet, Rev. 2.21 744 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.1 Introduction The S12XDBG module provides an on-chip trace buffer with flexible triggering capability to allow non-intrusive debug of application software. The S12XDBG module is optimized for the HCS12X 16-bit architecture and allows debugging of both S12XCPU and XGATE module operations. Typically the S12XDBG module is used in conjunction with the S12XBDM module, whereby the user configures the S12XDBG module for a debugging session over the BDM interface. Once configured the S12XDBG module is armed and the device leaves BDM Mode returning control to the user program, which is then monitored by the S12XDBG module. Alternatively the S12XDBG module can be configured over a serial interface using SWI routines. 20.1.1 Glossary Of Terms COF: Change Of Flow. Change in the program flow due to a conditional branch, indexed jump or interrupt. BDM : Background Debug Mode DUG: Device User Guide, describing the features of the device into which the DBG is integrated. WORD: 16 bit data entity Data Line : 64 bit data entity XGATE : S12X family programmable Direct Memory Access Module CPU : S12X_CPU module Tag : Tags can be attached to XGATE or CPU opcodes as they enter the instruction pipe. If the tagged opcode reaches the execution stage a tag hit occurs. 20.1.2 Overview The comparators monitor the bus activity of the S12XCPU and XGATE modules. When a match occurs the control logic can trigger the state sequencer to a new state. On a transition to the Final State, bus tracing is triggered and/or a breakpoint can be generated. Independent of comparator matches a transition to Final State with associated tracing and breakpoint can be triggered by the external TAGHI and TAGLO signals, by an XGATE module S/W breakpoint request or an immediate trigger, instigated by writing to the TRIG control bit. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 745 Chapter 20 S12X Debug (S12XDBGV3) Module The trace buffer is visible through a 2-byte window in the register address map and can be read out using standard 16-bit word reads. Tracing is disabled when the MCU system is secured. 20.1.3 * * * * * * * Features Four comparators (A, B, C, and D) -- Comparators A and C compare the full address bus and full 16-bit data bus -- Comparators A and C feature a data bus mask register -- Comparators B and D compare the full address bus only -- Each comparator can be configured to monitor either S12XCPU or XGATE buses -- Each comparator features control of R/W and byte/word access cycles -- Comparisons can be used as triggers for the state sequencer Three comparator modes -- Simple address/data comparator match mode -- Inside address range mode, Addmin Address Addmax -- Outside address range match mode, Address < Addmin or Address > Addmax Two types of triggers -- Tagged -- This triggers just before a specific instruction begins execution -- Force -- This triggers on the first instruction boundary after a match occurs. Three types of breakpoints -- S12XCPU breakpoint entering BDM on breakpoint (BDM) -- S12XCPU breakpoint executing SWI on breakpoint (SWI) -- XGATE breakpoint Three trigger modes independent of comparators -- External instruction tagging (associated with S12XCPU instructions only) -- XGATE S/W breakpoint request -- TRIG Immediate software trigger Four trace modes -- Normal: change of flow (COF) PC information is stored (see Section 20.4.5.2.1) for change of flow definition. -- Loop1: same as Normal but inhibits consecutive duplicate source address entries -- Detail: address and data for all cycles except free cycles and opcode fetches are stored -- Pure PC: All program counter addresses are stored. 4-stage state sequencer for trace buffer control -- Tracing session trigger linked to Final State of state sequencer -- Begin, End, and Mid alignment of tracing to trigger 20.1.4 Modes of Operation The S12XDBG module can be used in all MCU functional modes. MC9S12XDP512 Data Sheet, Rev. 2.21 746 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module During BDM hardware accesses and whilst the BDM module is active, S12XCPU monitoring is disabled. Thus breakpoints, comparators, and bus tracing mapped to the S12XCPU are disabled but XGATE bus monitoring accessing the S12XDBG registers, including comparator registers, is still possible. While in active BDM or during hardware BDM accesses, XGATE activity can still be compared, traced and can be used to generate a breakpoint to the XGATE module. When the S12XCPU enters active BDM Mode through a BACKGROUND command, with the S12XDBG module armed, the S12XDBG remains armed. The S12XDBG module tracing is disabled if the MCU is secure. However, breakpoints can still be generated if the MCU is secure. Table 20-1. Mode Dependent Restriction Summary BDM Enable BDM Active MCU Secure Comparator Matches Enabled Breakpoints Possible Tagging Possible Tracing Possible x x 1 Yes Yes Yes No 0 0 0 Yes Only SWI Yes Yes 0 1 0 1 0 0 Yes Yes Yes Yes 1 1 0 XGATE only XGATE only XGATE only XGATE only 20.1.5 Active BDM not possible when not enabled Block Diagram TAGS TAGHITS EXTERNAL TAGHI / TAGLO BREAKPOINT REQUESTS XGATE S/W BREAKPOINT REQUEST S12XCPU & XGATE XGATE BUS COMPARATOR A COMPARATOR B COMPARATOR C COMPARATOR D MATCH0 COMPARATOR MATCH CONTROL S12XCPU BUS BUS INTERFACE SECURE MATCH1 TAG & TRIGGER CONTROL LOGIC TRIGGER MATCH2 STATE STATE SEQUENCER STATE MATCH3 TRACE CONTROL TRIGGER TRACE BUFFER READ TRACE DATA (DBG READ DATA BUS) Figure 20-1. Debug Module Block Diagram 20.2 External Signal Description The S12XDBG sub-module features two external tag input signals. See Device User Guide (DUG) for the mapping of these signals to device pins. These tag pins may be used for the external tagging in emulation modes only. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 747 Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-2. External System Pins Associated With S12XDBG Pin Name Pin Functions TAGHI (See DUG) TAGHI When instruction tagging is on, tags the high half of the instruction word being read into the instruction queue. TAGLO (See DUG) TAGLO When instruction tagging is on, tags the low half of the instruction word being read into the instruction queue. TAGLO (See DUG) Unconditional Tagging Enable In emulation modes, a low assertion on this pin in the 7th or 8th cycle after the end of reset enables the Unconditional Tagging function. 20.3 20.3.1 Description Memory Map and Registers Module Memory Map A summary of the registers associated with the S12XDBG sub-block is shown in Table 20-2. Detailed descriptions of the registers and bits are given in the subsections that follow. Address Name Bit 7 6 0 TRIG 5 4 XGSBPE BDM 0 0 3 2 1 Bit 0 0x0020 DBGC1 R W 0x0021 DBGSR R W 0x0022 DBGTCR R W 0x0023 DBGC2 R W 0 0 0 0 0x0024 DBGTBH R W Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0x0025 DBGTBL R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0x0026 DBGCNT R W 0 0x0027 DBGSCRX 0 0 0 0 SC3 SC2 SC1 SC0 0x0027 DBGMFR R W R W 0 0 0 0 MC3 MC2 MC1 MC0 NDB TAG BRK RW RWE SRC COMPE SZ TAG BRK RW RWE SRC COMPE Bit 22 21 20 19 18 17 Bit 16 0x00281 0x00282 0x0029 DBGXCTL R (COMPA/C) W DBGXCTL R (COMPB/D) W DBGXAH R W ARM TBF EXTF TSOURCE 0 SZE 0 DBGBRK 0 TRANGE COMRV SSF2 SSF1 SSF0 TRCMOD TALIGN CDCM ABCM CNT Figure 20-2. Quick Reference to S12XDBG Registers MC9S12XDP512 Data Sheet, Rev. 2.21 748 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module Address Name Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 0x002A DBGXAM R W 0x002B DBGXAL R W Bit 7 6 5 4 3 2 1 Bit 0 0x002C DBGXDH R W Bit 15 14 13 12 11 10 9 Bit 8 0x002D DBGXDL R W Bit 7 6 5 4 3 2 1 Bit 0 0x002E DBGXDHM R W Bit 15 14 13 12 11 10 9 Bit 8 1 Bit 0 R Bit 7 6 5 4 3 2 W 1 This represents the contents if the Comparator A or C control register is blended into this address. 2 This represents the contents if the Comparator B or D control register is blended into this address 0x002F DBGXDLM Figure 20-2. Quick Reference to S12XDBG Registers 20.3.2 Register Descriptions This section consists of the S12XDBG control and trace buffer register descriptions in address order. Each comparator has a bank of registers that are visible through an 8-byte window between 0x0028 and 0x002F in the S12XDBG module register address map. When ARM is set in DBGC1, the only bits in the S12XDBG module registers that can be written are ARM, TRIG, and COMRV[1:0] 20.3.2.1 Debug Control Register 1 (DBGC1) Address: 0x0020 7 R W Reset 6 ARM 0 0 TRIG 0 5 4 XGSBPE BDM 0 0 3 2 1 DBGBRK 0 0 COMRV 0 0 0 Figure 20-3. Debug Control Register (DBGC1) Read: Anytime Write: Bits 7, 1, 0 anytime, bit 6 can be written anytime but always reads back as 0. Bits 5:2 anytime S12XDBG is not armed. NOTE When disarming the S12XDBG by clearing ARM with software, the contents of bits[5:2] are not affected by the write, since up until the write operation, ARM = 1 preventing these bits from being written. These bits must be cleared using a second write if required. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 749 Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-3. DBGC1 Field Descriptions Field Description 7 ARM Arm Bit -- The ARM bit controls whether the S12XDBG module is armed. This bit can be set and cleared by user software and is automatically cleared on completion of a tracing session, or if a breakpoint is generated with tracing not enabled. On setting this bit the state sequencer enters State1. When ARM is set, the only bits in the S12XDBG module registers that can be written are ARM and TRIG. 0 Debugger disarmed 1 Debugger armed 6 TRIG Immediate Trigger Request Bit -- This bit when written to 1 requests an immediate trigger independent of comparator or external tag signal status. When tracing is complete a forced breakpoint may be generated depending upon DBGBRK and BDM bit settings. This bit always reads back a 0. Writing a 0 to this bit has no effect. If both TSOURCE bits are clear no tracing is carried out. If tracing has already commenced using BEGINor MID trigger alignment, it continues until the end of the tracing session as defined by the TALIGN bit settings, thus TRIG has no affect. In secure mode tracing is disabled and writing to this bit has no effect. 0 Do not trigger until the state sequencer enters the Final State. 1 Enter Final State immediately and issue forced breakpoint request when trace buffer is full. 5 XGSBPE XGATE S/W Breakpoint Enable -- The XGSBPE bit controls whether an XGATE S/W breakpoint request is passed to the S12XCPU. The XGATE S/W breakpoint request is handled by the S12XDBG module, which can request an S12XCPU breakpoint depending on the state of this bit. 0 XGATE S/W breakpoint request is disabled 1 XGATE S/W breakpoint request is enabled 4 BDM Background Debug Mode Enable -- This bit determines if a S12X breakpoint causes the system to enter Background Debug Mode (BDM) or initiate a Software Interrupt (SWI). It has no affect on S12XDBG functionality. If this bit is set but the BDM is not enabled by the ENBDM bit in the BDM module, then breakpoints default to SWI. 0 Breakpoint to Software Interrupt if BDM inactive. Otherwise no breakpoint. 1 Breakpoint to BDM, if BDM enabled. Otherwise breakpoint to SWI 3-2 DBGBRK S12XDBG Breakpoint Enable Bits -- The DBGBRK bits control whether the debugger will request a breakpoint to either S12XCPU or XGATE or both upon reaching the state sequencer Final State. If tracing is enabled, the breakpoint is generated on completion of the tracing session. If tracing is not enabled, the breakpoint is generated immediately. Please refer to Section 20.4.7 for further details. XGATE software breakpoints are independent of the DBGBRK bits. XGATE software breakpoints force a breakpoint to the S12XCPU independent of the DBGBRK bit field configuration. See Table 20-4. 1-0 COMRV Comparator Register Visibility Bits -- These bits determine which bank of comparator register is visible in the 8-byte window of the S12XDBG module address map, located between 0x0028 to 0x002F. Furthermore these bits determine which register is visible at the address 0x0027. See Table 20-5. Table 20-4. DBGBRK Encoding DBGBRK Resource Halted by Breakpoint 00 No breakpoint generated 01 XGATE breakpoint generated 10 S12XCPU breakpoint generated 11 Breakpoints generated for S12XCPU and XGATE Table 20-5. COMRV Encoding COMRV Visible Comparator Visible Register at 0x0027 00 Comparator A DBGSCR1 01 Comparator B DBGSCR2 MC9S12XDP512 Data Sheet, Rev. 2.21 750 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-5. COMRV Encoding COMRV Visible Comparator Visible Register at 0x0027 10 Comparator C DBGSCR3 11 Comparator D DBGMFR MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 751 Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.2 Debug Status Register (DBGSR) Address: 0x0021 R 7 6 5 4 3 2 1 0 TBF EXTF 0 0 0 SSF2 SSF1 SSF0 -- 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset POR = Unimplemented or Reserved Figure 20-4. Debug Status Register (DBGSR) Read: Anytime Write: Never Table 20-6. DBGSR Field Descriptions Field Description 7 TBF Trace Buffer Full -- The TBF bit indicates that the trace buffer has stored 64 or more lines of data since it was last armed. If this bit is set, then all 64 lines will be valid data, regardless of the value of DBGCNT bits CNT[6:0]. The TBF bit is cleared when ARM in DBGC1 is written to a one. The TBF is cleared by the power on reset initialization. Other system generated resets have no affect on this bit 6 EXTF External Tag Hit Flag -- The EXTF bit indicates if a tag hit condition from an external TAGHI/TAGLO tag was met since arming. This bit is cleared when ARM in DBGC1 is written to a one. 0 External tag hit has not occurred 1 External tag hit has occurred 2-0 SSF[2:0] State Sequencer Flag Bits -- The SSF bits indicate in which state the State Sequencer is currently in. During a debug session on each transition to a new state these bits are updated. If the debug session is ended by software clearing the ARM bit, then these bits retain their value to reflect the last state of the state sequencer before disarming. If a debug session is ended by an internal trigger, then the state sequencer returns to state0 and these bits are cleared to indicate that state0 was entered during the session. On arming the module the state sequencer enters state1 and these bits are forced to SSF[2:0] = 001. See Table 20-7. Table 20-7. SSF[2:0] -- State Sequence Flag Bit Encoding SSF[2:0] Current State 000 State0 (disarmed) 001 State1 010 State2 011 State3 100 Final State 101,110,111 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 752 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.3 Debug Trace Control Register (DBGTCR) Address: 0x0022 7 6 R TSOURCE W Reset 5 0 4 3 TRANGE 0 0 2 1 TRCMOD 0 0 0 TALIGN 0 0 0 Figure 20-5. Debug Trace Control Register (DBGTCR) Read: Anytime Write: Bits 7:6 only when S12XDBG is neither secure nor armed. Bits 5:0 anytime the module is disarmed. Table 20-8. DBGTCR Field Descriptions Field 7-6 TSOURCE Description Trace Source Control Bits -- The TSOURCE bits select the data source for the tracing session. If the MCU system is secured, these bits cannot be set and tracing is inhibited. See Table 20-9. 5-4 TRANGE Trace Range Bits -- The TRANGE bits allow filtering of trace information from a selected address range when tracing from the S12XCPU in Detail Mode. The XGATE tracing range cannot be narrowed using these bits. To use a comparator for range filtering, the corresponding COMPE and SRC bits must remain cleared. If the COMPE bit is not clear then the comparator will also be used to generate state sequence triggers. If the corresponding SRC bit is set the comparator is mapped to the XGATE buses, the TRANGE bits have no effect on the valid address range, memory accesses within the whole memory map are traced. See Table 20-10. 3-2 TRCMOD Trace Mode Bits -- See Section 20.4.5.2 for detailed Trace Mode descriptions. In Normal Mode, change of flow information is stored. In Loop1 Mode, change of flow information is stored but redundant entries into trace memory are inhibited. In Detail Mode, address and data for all memory and register accesses is stored. See Table 20-11. 1-0 TALIGN Trigger Align Bits -- These bits control whether the trigger is aligned to the beginning, end or the middle of a tracing session. See Table 20-12. Table 20-9. TSOURCE -- Trace Source Bit Encoding TSOURCE Tracing Source 00 No tracing requested 01 S12XCPU 101 XGATE 11 1 2 1,2 Both S12XCPU and XGATE No range limitations are allowed. Thus tracing operates as if TRANGE = 00. No Detail Mode tracing supported. If TRCMOD = 10, no information is stored. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 753 Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-10. TRANGE Trace Range Encoding TRANGE Tracing Range 00 Trace from all addresses (No filter) 01 Trace only in address range from $00000 to Comparator D 10 Trace only in address range from Comparator C to $7FFFFF 11 Trace only in range from Comparator C to Comparator D Table 20-11. TRCMOD Trace Mode Bit Encoding TRCMOD Description 00 Normal 01 Loop1 10 Detail 11 Pure PC Table 20-12. TALIGN Trace Alignment Encoding TALIGN Description 00 Trigger at end of stored data 01 Trigger before storing data 10 Trace buffer entries before and after trigger 11 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 754 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.4 Debug Control Register2 (DBGC2) Address: 0x0023 R 7 6 5 4 0 0 0 0 0 0 0 0 3 1 CDCM W Reset 2 0 0 ABCM 0 0 0 = Unimplemented or Reserved Figure 20-6. Debug Control Register2 (DBGC2) Read: Anytime Write: Anytime the module is disarmed. This register configures the comparators for range matching. Table 20-13. DBGC2 Field Descriptions Field Description 3-2 CDCM[1:0] C and D Comparator Match Control -- These bits determine the C and D comparator match mapping as described in Table 20-14. 1-0 ABCM[1:0] A and B Comparator Match Control -- These bits determine the A and B comparator match mapping as described in Table 20-15. Table 20-14. CDCM Encoding CDCM Description 00 Match2 mapped to comparator C match....... Match3 mapped to comparator D match. 01 Match2 mapped to comparator C/D inside range....... Match3 disabled. 10 Match2 mapped to comparator C/D outside range....... Match3 disabled. 11 Reserved Table 20-15. ABCM Encoding ABCM Description 00 Match0 mapped to comparator A match....... Match1 mapped to comparator B match. 01 Match 0 mapped to comparator A/B inside range....... Match1 disabled. 10 Match 0 mapped to comparator A/B outside range....... Match1 disabled. 11 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 755 Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.5 Debug Trace Buffer Register (DBGTBH:DBGTBL) Address: 0x0024, 0x0025 15 R W 14 13 12 11 10 9 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Reset X X X X X X X 8 7 6 5 4 3 2 1 0 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 X X X X X X X X X Figure 20-7. Debug Trace Buffer Register (DBGTB) Read: Anytime when unlocked and not secured and not armed. Write: Aligned word writes when disarmed unlock the trace buffer for reading but do not affect trace buffer contents. Table 20-16. DBGTB Field Descriptions Field Description 15-0 Bit[15:0] Trace Buffer Data Bits -- The Trace Buffer Register is a window through which the 64-bit wide data lines of the Trace Buffer may be read 16 bits at a time. Each valid read of DBGTB increments an internal trace buffer pointer which points to the next address to be read. When the ARM bit is written to 1 the trace buffer is locked to prevent reading. The trace buffer can only be unlocked for reading by writing to DBGTB with an aligned word write when the module is disarmed. The DBGTB register can be read only as an aligned word, any byte reads or misaligned access of these registers will return 0 and will not cause the trace buffer pointer to increment to the next trace buffer address. The same is true for word reads while the debugger is armed. System resets do not affect the trace buffer contents. The POR state is undefined. MC9S12XDP512 Data Sheet, Rev. 2.21 756 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.6 Debug Count Register (DBGCNT) Address: 0x0026 7 R 6 5 4 0 3 2 1 0 -- 0 -- 0 -- 0 CNT W Reset POR 0 0 -- 0 -- 0 -- 0 -- 0 = Unimplemented or Reserved Figure 20-8. Debug Count Register (DBGCNT) Read: Anytime Write: Never Table 20-17. DBGCNT Field Descriptions Field Description 6-0 CNT[6:0] Count Value -- The CNT bits [6:0] indicate the number of valid data 64-bit data lines stored in the Trace Buffer. Table 20-18 shows the correlation between the CNT bits and the number of valid data lines in the Trace Buffer. When the CNT rolls over to zero, the TBF bit in DBGSR is set and incrementing of CNT will continue in end-trigger or mid-trigger mode. The DBGCNT register is cleared when ARM in DBGC1 is written to a one. The DBGCNT register is cleared by power-on-reset initialization but is not cleared by other system resets. Thus should a reset occur during a debug session, the DBGCNT register still indicates after the reset, the number of valid trace buffer entries stored before the reset occurred. The DBGCNT register is not decremented when reading from the trace buffer. Table 20-18. CNT Decoding Table 1 TBF (DBGSR) CNT[6:0] Description 0 0000000 No data valid 0 0000001 32 bits of one line valid1 0 0000010 0000100 0000110 .. 1111100 1 line valid 2 lines valid 3 lines valid .. 62 lines valid 0 1111110 63 lines valid 1 0000000 64 lines valid; if using Begin trigger alignment, ARM bit will be cleared and the tracing session ends. 1 0000010 .. .. 1111110 64 lines valid, oldest data has been overwritten by most recent data This applies to Normal/Loop1 Modes when tracing from either S12XCPU or XGATE only. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 757 Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.7 Debug State Control Registers There is a dedicated control register for each of the state sequencer states 1 to 3 that determines if transitions from that state are allowed, depending upon comparator matches or tag hits, and defines the next state for the state sequencer following a match. The three debug state control registers are located at the same address in the register address map (0x0027). Each register can be accessed using the COMRV bits in DBGC1 to blend in the required register. The COMRV = 11 value blends in the match flag register (DBGMFR). Table 20-19. State Control Register Access Encoding COMRV Visible State Control Register 00 DBGSCR1 01 DBGSCR2 10 DBGSCR3 11 DBGMFR MC9S12XDP512 Data Sheet, Rev. 2.21 758 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.7.1 Debug State Control Register 1 (DBGSCR1) Address: 0x0027 R 7 6 5 4 0 0 0 0 0 0 0 W Reset 0 3 2 1 0 SC3 SC2 SC1 SC0 0 0 0 0 = Unimplemented or Reserved Figure 20-9. Debug State Control Register 1 (DBGSCR1) Read: Anytime Write: Anytime when S12XDBG not armed. This register is visible at 0x0027 only with COMRV[1:0] = 00. The state control register 1 selects the targeted next state whilst in State1. The matches refer to the match channels of the comparator match control logic as depicted in Figure 20-1 and described in Section 20.3.2.8.1". Comparators must be enabled by setting the comparator enable bit in the associated DBGXCTL control register. Table 20-20. DBGSCR1 Field Descriptions Field 3-0 SC[3:0] Description These bits select the targeted next state whilst in State1, based upon the match event. Table 20-21. State1 Sequencer Next State Selection SC[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Description Any match triggers to state2 Any match triggers to state3 Any match triggers to Final State Match2 triggers to State2....... Other matches have no effect Match2 triggers to State3....... Other matches have no effect Match2 triggers to Final State....... Other matches have no effect Match0 triggers to State2....... Match1 triggers to State3....... Other matches have no effect Match1 triggers to State3....... Match0 triggers Final State....... Other matches have no effect Match0 triggers to State2....... Match2 triggers to State3....... Other matches have no effect Match2 triggers to State3....... Match0 triggers Final State....... Other matches have no effect Match1 triggers to State2....... Match3 triggers to State3....... Other matches have no effect Match3 triggers to State3....... Match1 triggers to Final State....... Other matches have no effect Match3 has no effect....... All other matches (M0,M1,M2) trigger to State2 Reserved Reserved Reserved The trigger priorities described in Table 20-38 dictate that in the case of simultaneous matches, the match on the lower channel number (0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 759 Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.7.2 Debug State Control Register 2 (DBGSCR2) Address: 0x0027 R 7 6 5 4 0 0 0 0 0 0 0 W Reset 0 3 2 1 0 SC3 SC2 SC1 SC0 0 0 0 0 = Unimplemented or Reserved Figure 20-10. Debug State Control Register 2 (DBGSCR2) Read: Anytime Write: Anytime when S12XDBG not armed. This register is visible at 0x0027 only with COMRV[1:0] = 01. The state control register 2 selects the targeted next state whilst in State2. The matches refer to the match channels of the comparator match control logic as depicted in Figure 20-1 and described in Section 20.3.2.8.1". Comparators must be enabled by setting the comparator enable bit in the associated DBGXCTL control register. Table 20-22. DBGSCR2 Field Descriptions Field 3-0 SC[3:0] Description These bits select the targeted next state whilst in State2, based upon the match event. Table 20-23. State2 --Sequencer Next State Selection SC[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Description Any match triggers to state1 Any match triggers to state3 Any match triggers to Final State Match3 triggers to State1....... Other matches have no effect Match3 triggers to State3....... Other matches have no effect Match3 triggers to Final State....... Other matches have no effect Match0 triggers to State1....... Match1 triggers to State3....... Other matches have no effect Match1 triggers to State3....... Match0 triggers Final State....... Other matches have no effect Match0 triggers to State1....... Match2 triggers to State3....... Other matches have no effect Match2 triggers to State3....... Match0 triggers Final State....... Other matches have no effect Match1 triggers to State1....... Match3 triggers to State3....... Other matches have no effect Match3 triggers to State3....... Match1 triggers Final State....... Other matches have no effect Match2 triggers to State1..... Match3 trigger to Final State Match2 has no affect, all other matches (M0,M1,M3) trigger to Final State Reserved Reserved The trigger priorities described in Table 20-38 dictate that in the case of simultaneous matches, the match on the lower channel number (0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches. MC9S12XDP512 Data Sheet, Rev. 2.21 760 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.7.3 Debug State Control Register 3 (DBGSCR3) Address: 0x0027 R 7 6 5 4 0 0 0 0 0 0 0 W Reset 0 3 2 1 0 SC3 SC2 SC1 SC0 0 0 0 0 = Unimplemented or Reserved Figure 20-11. Debug State Control Register 3 (DBGSCR3) Read: Anytime Write: Anytime when S12XDBG not armed. This register is visible at 0x0027 only with COMRV[1:0] = 10. The state control register three selects the targeted next state whilst in State3. The matches refer to the match channels of the comparator match control logic as depicted in Figure 20-1 and described in Section 20.3.2.8.1". Comparators must be enabled by setting the comparator enable bit in the associated DBGXCTL control register. Table 20-24. DBGSCR3 Field Descriptions Field 3-0 SC[3:0] Description These bits select the targeted next state whilst in State3, based upon the match event. Table 20-25. State3 -- Sequencer Next State Selection SC[3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Description Any match triggers to state1 Any match triggers to state2 Any match triggers to Final State Match0 triggers to State1....... Other matches have no effect Match0 triggers to State2....... Other matches have no effect Match0 triggers to Final State.......Match1 triggers to State1 Match1 triggers to State1....... Other matches have no effect Match1 triggers to State2....... Other matches have no effect Match1 triggers to Final State....... Other matches have no effect Match2 triggers to State2....... Match0 triggers to Final State....... Other matches have no effect Match1 triggers to State1....... Match3 triggers to State2....... Other matches have no effect Match3 triggers to State2....... Match1 triggers to Final State....... Other matches have no effect Match2 triggers to Final State....... Other matches have no effect Match3 triggers to Final State....... Other matches have no effect Reserved Reserved The trigger priorities described in Table 20-38 dictate that in the case of simultaneous matches, the match on the lower channel number (0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 761 Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.7.4 Debug Match Flag Register (DBGMFR) Address: 0x0027 R 7 6 5 4 3 2 1 0 0 0 0 0 MC3 MC2 MC1 MC0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 20-12. Debug Match Flag Register (DBGMFR) Read: Anytime Write: Never DBGMFR is visible at 0x0027 only with COMRV[1:0] = 11. It features four flag bits each mapped directly to a channel. Should a match occur on the channel during the debug session, then the corresponding flag is set and remains set until the next time the module is armed by writing to the ARM bit. Thus the contents are retained after a debug session for evaluation purposes. These flags cannot be cleared by software, they are cleared only when arming the module. A set flag does not inhibit the setting of other flags. Once a flag is set, further triggers on the same channel have no affect. 20.3.2.8 Comparator Register Descriptions Each comparator has a bank of registers that are visible through an 8-byte window in the S12XDBG module register address map. Comparators A and C consist of 8 register bytes (3 address bus compare registers, two data bus compare registers, two data bus mask registers and a control register). Comparators B and D consist of four register bytes (three address bus compare registers and a control register). Each set of comparator registers is accessible in the same 8-byte window of the register address map and can be accessed using the COMRV bits in the DBGC1 register. If the Comparators B or D are accessed through the 8-byte window, then only the address and control bytes are visible, the 4 bytes associated with data bus and data bus masking read as zero and cannot be written. Furthermore the control registers for comparators B and D differ from those of comparators A and C. Table 20-26. Comparator Register Layout 0x0028 CONTROL Read/Write -- 0x0029 ADDRESS HIGH Read/Write -- 0x002A ADDRESS MEDIUM Read/Write -- 0x002B ADDRESS LOW Read/Write -- 0x002C DATA HIGH COMPARATOR Read/Write Comparator A and C only 0x002D DATA LOW COMPARATOR Read/Write Comparator A and C only 0x002E DATA HIGH MASK Read/Write Comparator A and C only 0x002F DATA LOW MASK Read/Write Comparator A and C only MC9S12XDP512 Data Sheet, Rev. 2.21 762 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.8.1 Debug Comparator Control Register (DBGXCTL) The contents of this register bits 7 and 6 differ depending upon which comparator registers are visible in the 8-byte window of the DBG module register address map. Address: 0x0028 7 R 0 W Reset 0 6 5 4 3 2 1 0 NDB TAG BRK RW RWE SRC COMPE 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 20-13. Debug Comparator Control Register (Comparators A and C) Address: 0x0028 R W 7 6 5 4 3 2 1 0 SZE SZ TAG BRK RW RWE SRC COMPE 0 0 0 0 0 0 0 0 Reset Figure 20-14. Debug Comparator Control Register (Comparators B and D) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-27. DBGXCTL Field Descriptions Field Description 7 SZE (Comparators B nd D) Size Comparator Enable Bit -- The SZE bit controls whether access size comparison is enabled for the associated comparator. This bit is ignored if the TAG bit in the same register is set. 0 Word/Byte access size is not used in comparison 1 Word/Byte access size is used in comparison 6 NDB (Comparators A and C Not Data Bus Compare -- The NDB bit controls whether the match occurs when the data bus matches the comparator register value or when the data bus differs from the register value. Furthermore data bus bits can be individually masked using the comparator data mask registers. This bit is only available for comparators A and C. This bit is ignored if the TAG bit in the same register is set. This bit position has an SZ functionality for comparators B and D. 0 Match on data bus equivalence to comparator register contents 1 Match on data bus difference to comparator register contents 6 SZ (Comparators B and D) Size Comparator Value Bit -- The SZ bit selects either word or byte access size in comparison for the associated comparator. This bit is ignored if the SZE bit is cleared or if the TAG bit in the same register is set. This bit position has NDB functionality for comparators A and C 0 Word access size will be compared 1 Byte access size will be compared 5 TAG Tag Select -- This bit controls whether the comparator match will cause a trigger or tag the opcode at the matched address. Tagged opcodes trigger only if they reach the execution stage of the instruction queue. 0 Trigger immediately on match 1 On match, tag the opcode. If the opcode is about to be executed a trigger is generated MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 763 Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-27. DBGXCTL Field Descriptions (continued) Field Description 4 BRK Break -- This bit controls whether a comparator match terminates a debug session immediately, independent of state sequencer state. To generate an immediate breakpoint the module breakpoints must be enabled using the DBGC1 bits DBGBRK[1:0]. 0 The debug session termination is dependent upon the state sequencer and trigger conditions. 1 A match on this channel terminates the debug session immediately; breakpoints if active are generated, tracing, if active, is terminated and the module disarmed. 3 RW Read/Write Comparator Value Bit -- The RW bit controls whether read or write is used in compare for the associated comparator. The RW bit is not used if RWE = 0. 0 Write cycle will be matched 1 Read cycle will be matched 2 RWE Read/Write Enable Bit -- The RWE bit controls whether read or write comparison is enabled for the associated comparator. This bit is not useful for tagged operations. 0 Read/Write is not used in comparison 1 Read/Write is used in comparison 1 SRC Determines mapping of comparator to S12XCPU or XGATE 0 The comparator is mapped to S12XCPU buses 1 The comparator is mapped to XGATE address and data buses 0 COMPE Determines if comparator is enabled 0 The comparator is not enabled 1 The comparator is enabled for state sequence triggers or tag generation Table 20-28 shows the effect for RWE and RW on the comparison conditions. These bits are not useful for tagged operations since the trigger occurs based on the tagged opcode reaching the execution stage of the instruction queue. Thus these bits are ignored if tagged triggering is selected. Table 20-28. Read or Write Comparison Logic Table RWE Bit RW Bit RW Signal Comment 0 x 0 RW not used in comparison 0 x 1 RW not used in comparison 1 0 0 Write data bus 1 0 1 No match 1 1 0 No match 1 1 1 Read data bus MC9S12XDP512 Data Sheet, Rev. 2.21 764 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.8.2 Debug Comparator Address High Register (DBGXAH) Address: 0x0029 7 R 0 W Reset 0 6 5 4 3 2 1 0 Bit 22 Bit 21 Bit 20 Bit 19 Bit 18 Bit 17 Bit 16 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure 20-15. Debug Comparator Address High Register (DBGXAH) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-29. DBGXAH Field Descriptions Field Description 6-0 Bit[22:16] Comparator Address High Compare Bits -- The Comparator address high compare bits control whether the selected comparator will compare the address bus bits [22:16] to a logic one or logic zero. This register byte is ignored for XGATE compares. 0 Compare corresponding address bit to a logic zero 1 Compare corresponding address bit to a logic one 20.3.2.8.3 Debug Comparator Address Mid Register (DBGXAM) Address: 0x002A R W Reset 7 6 5 4 3 2 1 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 20-16. Debug Comparator Address Mid Register (DBGXAM) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-30. DBGXAM Field Descriptions Field 7-0 Bit[15:8] Description Comparator Address Mid Compare Bits -- The Comparator address mid compare bits control whether the selected comparator will compare the address bus bits [15:8] to a logic one or logic zero. 0 Compare corresponding address bit to a logic zero 1 Compare corresponding address bit to a logic one MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 765 Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.8.4 Debug Comparator Address Low Register (DBGXAL) Address: 0x002B R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 20-17. Debug Comparator Address Low Register (DBGXAL) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-31. DBGXAL Field Descriptions Field 7-0 Bits[7:0] Description Comparator Address Low Compare Bits -- The Comparator address low compare bits control whether the selected comparator will compare the address bus bits [7:0] to a logic one or logic zero. 0 Compare corresponding address bit to a logic zero 1 Compare corresponding address bit to a logic one 20.3.2.8.5 Debug Comparator Data High Register (DBGXDH) Address: 0x002C R W Reset 7 6 5 4 3 2 1 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 20-18. Debug Comparator Data High Register (DBGXDH) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-32. DBGXAH Field Descriptions Field Description 7-0 Bits[15:8] Comparator Data High Compare Bits -- The Comparator data high compare bits control whether the selected comparator compares the data bus bits [15:8] to a logic one or logic zero. The comparator data compare bits are only used in comparison if the corresponding data mask bit is logic 1. This register is available only for comparators A and C. 0 Compare corresponding data bit to a logic zero 1 Compare corresponding data bit to a logic one MC9S12XDP512 Data Sheet, Rev. 2.21 766 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.8.6 Debug Comparator Data Low Register (DBGXDL) Address: 0x002D R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 20-19. Debug Comparator Data Low Register (DBGXDL) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-33. DBGXDL Field Descriptions Field Description 7-0 Bits[7:0] Comparator Data Low Compare Bits -- The Comparator data low compare bits control whether the selected comparator compares the data bus bits [7:0] to a logic one or logic zero. The comparator data compare bits are only used in comparison if the corresponding data mask bit is logic 1. This register is available only for comparators A and C. 0 Compare corresponding data bit to a logic zero 1 Compare corresponding data bit to a logic one 20.3.2.8.7 Debug Comparator Data High Mask Register (DBGXDHM) Address: 0x002E R W Reset 7 6 5 4 3 2 1 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 0 0 0 0 0 0 0 0 Figure 20-20. Debug Comparator Data High Mask Register (DBGXDHM) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-34. DBGXDHM Field Descriptions Field Description 7-0 Bits[15:8] Comparator Data High Mask Bits -- The Comparator data high mask bits control whether the selected comparator compares the data bus bits [15:8] to the corresponding comparator data compare bits. This register is available only for comparators A and C. 0 Do not compare corresponding data bit 1 Compare corresponding data bit MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 767 Chapter 20 S12X Debug (S12XDBGV3) Module 20.3.2.8.8 Debug Comparator Data Low Mask Register (DBGXDLM) Address: 0x002F R W Reset 7 6 5 4 3 2 1 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Figure 20-21. Debug Comparator Data Low Mask Register (DBGXDLM) Read: Anytime Write: Anytime when S12XDBG not armed. Table 20-35. DBGXDLM Field Descriptions Field Description 7-0 Bits[7:0] Comparator Data Low Mask Bits -- The Comparator data low mask bits control whether the selected comparator compares the data bus bits [7:0] to the corresponding comparator data compare bits. This register is available only for comparators A and C. 0 Do not compare corresponding data bit 1 Compare corresponding data bit 20.4 Functional Description This section provides a complete functional description of the S12XDBG module. If the part is in secure mode, the S12XDBG module can generate breakpoints but tracing is not possible. 20.4.1 S12XDBG Operation Arming the S12XDBG module by setting ARM in DBGC1 allows triggering, and storing of data in the trace buffer and can be used to cause breakpoints to the S12XCPU or the XGATE module. The DBG module is made up of four main blocks, the comparators, control logic, the state sequencer, and the trace buffer. The comparators monitor the bus activity of the S12XCPU and XGATE modules. Comparators can be configured to monitor address and databus. Comparators can also be configured to mask out individual data bus bits during a compare and to use R/W and word/byte access qualification in the comparison. When a match with a comparator register value occurs the associated control logic can trigger the state sequencer to another state (see Figure 20-23). Either forced or tagged triggers are possible. Using a forced trigger, the trigger is generated immediately on a comparator match. Using a tagged trigger, at a comparator match, the instruction opcode is tagged and only if the instruction reaches the execution stage of the instruction queue is a trigger generated. In the case of a transition to Final State, bus tracing is triggered and/or a breakpoint can be generated. Tracing of both S12XCPU and/or XGATE bus activity is possible. Independent of the state sequencer, a breakpoint can be triggered by the external TAGHI / TAGLO signals, by an XGATE S/W breakpoint request or by writing to the TRIG bit in the DBGC1 control register. MC9S12XDP512 Data Sheet, Rev. 2.21 768 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module The trace buffer is visible through a 2-byte window in the register address map and can be read out using standard 16-bit word reads. TAGS TAGHITS EXTERNAL TAGHI / TAGLO BREAKPOINT REQUESTS XGATE S/W BREAKPOINT REQUEST S12XCPU & XGATE XGATE BUS COMPARATOR A COMPARATOR B COMPARATOR C COMPARATOR D MATCH0 COMPARATOR MATCH CONTROL S12XCPU BUS BUS INTERFACE SECURE MATCH1 TAG & TRIGGER CONTROL LOGIC MATCH2 TRIGGER STATE STATE SEQUENCER STATE MATCH3 TRACE CONTROL TRIGGER TRACE BUFFER READ TRACE DATA (DBG READ DATA BUS) Figure 20-22. S12XDBG Overview 20.4.2 Comparator Modes The S12XDBG contains four comparators, A, B, C, and D. Each comparator can be configured to monitor either S12XCPU or XGATE buses using the SRC bit in the corresponding comparator control register. Each comparator compares the selected address bus with the address stored in DBGXAH, DBGXAM, and DBGXAL. Furthermore, comparators A and C also compare the data buses to the data stored in DBGXDH, DBGXDL and allow masking of individual data bus bits. All comparators are disabled in BDM and during BDM accesses. The comparator match control logic (see Figure 20-22) configures comparators to monitor the buses for an exact address or an address range, whereby either an access inside or outside the specified range generates a match condition. The comparator configuration is controlled by the control register contents and the range control by the DBGC2 contents. On a match a trigger can initiate a transition to another state sequencer state (see Section 20.4.3"). The comparator control register also allows the type of access to be included in the comparison through the use of the RWE, RW, SZE, and SZ bits. The RWE bit controls whether read or write comparison is enabled for the associated comparator and the RW bit selects either a read or write access for a valid match. Similarly the SZE and SZ bits allows the size of access (word or byte) to be considered in the compare. Only comparators B and D feature SZE and SZ. The TAG bit in each comparator control register is used to determine the triggering condition. By setting TAG, the comparator will qualify a match with the output of opcode tracking logic and a trigger occurs MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 769 Chapter 20 S12X Debug (S12XDBGV3) Module before the tagged instruction executes (tagged-type trigger). Whilst tagging the RW, RWE, SZE, and SZ bits are ignored and the comparator register must be loaded with the exact opcode address. If the TAG bit is clear (forced type trigger) a comparator match is generated when the selected address appears on the system address bus. If the selected address is an opcode address, the match is generated when the opcode is fetched from the memory. This precedes the instruction execution by an indefinite number of cycles due to instruction pipe lining. For a comparator match of an opcode at an odd address when TAG = 0, the corresponding even address must be contained in the comparator register. Thus for an opcode at odd address (n), the comparator register must contain address (n-1). Once a successful comparator match has occurred, the condition that caused the original match is not verified again on subsequent matches. Thus if a particular data value is verified at a given address, this address may not still contain that data value when a subsequent match occurs. Comparators C and D can also be used to select an address range to trace from. This is determined by the TRANGE bits in the DBGTCR register. The TRANGE encoding is shown in Table 20-10. If the TRANGE bits select a range definition using comparator D, then comparator D is configured for trace range definition and cannot be used for address bus comparisons. Similarly if the TRANGE bits select a range definition using comparator C, then comparator C is configured for trace range definition and cannot be used for address bus comparisons. Match[0, 1, 2, 3] map directly to Comparators[A, B, C, D] respectively, except in range modes (see Section 20.3.2.4"). Comparator priority rules are described in the trigger priority section (Section 20.4.3.6"). 20.4.2.1 Exact Address Comparator Match (Comparators A and C) With range comparisons disabled, the match condition is an exact equivalence of address/data bus with the value stored in the comparator address/data registers. Further qualification of the type of access (R/W, word/byte) is possible. Comparators A and C do not feature SZE or SZ control bits, thus the access size is not compared. The exact address is compared, thus with the comparator address register loaded with address (n) a misaligned word access of address (n-1) also accesses (n) but does not cause a match. Table 20-37 lists access considerations without data bus compare. Table 20-36 lists access considerations with data bus comparison. To compare byte accesses DBGXDH must be loaded with the data byte. The low byte must be masked out using the DBGXDLM mask register. On word accesses the data byte of the lower address is mapped to DBGXDH. Table 20-36. Comparator A and C Data Bus Considerations Access Address DBGxDH DBGxDL DBGxDHM DBGxDLM Example Valid Match Word ADDR[n] Data[n] Byte ADDR[n] Data[n] Data[n+1] $FF $FF MOVW #$WORD ADDR[n] x $FF $00 MOVB #$BYTE ADDR[n] Word ADDR[n] Data[n] x $FF $00 MOVW #$WORD ADDR[n] Word ADDR[n] x Data[n+1] $00 $FF MOVW #$WORD ADDR[n] MC9S12XDP512 Data Sheet, Rev. 2.21 770 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module Comparators A and C feature an NDB control bit to determine if a match occurs when the data bus differs to comparator register contents or when the data bus is equivalent to the comparator register contents. 20.4.2.2 Exact Address Comparator Match (Comparators B and D) Comparators B and D feature SZ and SZE control bits. If SZE is clear, then the comparator address match qualification functions the same as for comparators A and C. If the SZE bit is set the access size (word or byte) is compared with the SZ bit value such that only the specified type of access causes a match. Thus if configured for a byte access of a particular address, a word access covering the same address does not lead to match. Table 20-37. Comparator Access Size Considerations 1 Comparator Address SZE SZ8 Condition For Valid Match Comparators A and C ADDR[n] -- -- Word and byte accesses of ADDR[n]1 MOVB #$BYTE ADDR[n] MOVW #$WORD ADDR[n] Comparators B and D ADDR[n] 0 X Word and byte accesses of ADDR[n]1 MOVB #$BYTE ADDR[n] MOVW #$WORD ADDR[n] Comparators B and D ADDR[n] 1 0 Word accesses of ADDR[n]1 MOVW #$WORD ADDR[n] Comparators B and D ADDR[n] 1 1 Byte accesses of ADDR[n] MOVB #$BYTE ADDR[n] A word access of ADDR[n-1] also accesses ADDR[n] but does not generate a match. The comparator address register must contain the exact address used in the code. 20.4.2.3 Range Comparisons When using the AB comparator pair for a range comparison, the data bus can also be used for qualification by using the comparator A data and data mask registers. Furthermore the DBGACTL RW and RWE bits can be used to qualify the range comparison on either a read or a write access. The corresponding DBGBCTL bits are ignored. Similarly when using the CD comparator pair for a range comparison, the data bus can also be used for qualification by using the comparator C data and data mask registers. Furthermore the DBGCCTL RW and RWE bits can be used to qualify the range comparison on either a read or a write access if tagging is not selected. The corresponding DBGDCTL bits are ignored. The SZE and SZ control bits are ignored in range mode. The comparator A and C TAG bits are used to tag range comparisons for the AB and CD ranges respectively. The comparator B and D TAG bits are ignored in range modes. In order for a range comparison using comparators A and B, both COMPEA and COMPEB must be set; to disable range comparisons both must be cleared. Similarly for a range CD comparison, both COMPEC and COMPED must be set. If a range mode is selected SRCA and SRCC select the source (S12X or XGATE), SRCB and SRCD are ignored. When configured for range comparisons and tagging, the ranges are accurate only to word boundaries. 20.4.2.3.1 Inside Range (CompAC_Addr address CompBD_Addr) In the Inside Range comparator mode, either comparator pair A and B or comparator pair C and D can be configured for range comparisons. This configuration depends upon the control register (DBGC2). The MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 771 Chapter 20 S12X Debug (S12XDBGV3) Module match condition requires that a valid match for both comparators happens on the same bus cycle. A match condition on only one comparator is not valid. An aligned word access which straddles the range boundary will cause a trigger only if the aligned address is inside the range. 20.4.2.3.2 Outside Range (address < CompAC_Addr or address > CompBD_Addr) In the Outside Range comparator mode, either comparator pair A and B or comparator pair C and D can be configured for range comparisons. A single match condition on either of the comparators is recognized as valid. An aligned word access which straddles the range boundary will cause a trigger only if the aligned address is outside the range. Outside range mode in combination with tagged triggers can be used to detect if the opcode fetches are from an unexpected range. In forced trigger modes the outside range trigger would typically be activated at any interrupt vector fetch or register access. This can be avoided by setting the upper range limit to $7FFFFF or lower range limit to $000000 respectively. When comparing the XGATE address bus in outside range mode, the initial vector fetch as determined by the vector contained in the XGATE XGVBR register should be taken into consideration. The XGVBR register and hence vector address can be modified. 20.4.3 Trigger Modes Trigger modes are used as qualifiers for a state sequencer change of state. The control logic determines the trigger mode and provides a trigger to the state sequencer. The individual trigger modes are described in the following sections. 20.4.3.1 Forced Trigger On Comparator Match If a forced trigger comparator match occurs, the trigger immediately initiates a transition to the next state sequencer state whereby the corresponding flags in DBGSR are set. The state control register for the current state determines the next state for each trigger. Forced triggers are generated as soon as the matching address appears on the address bus, which in the case of opcode fetches occurs several cycles before the opcode execution. For this reason a forced trigger of an opcode address precedes a tagged trigger at the same address by several cycles. 20.4.3.2 Trigger On Comparator Related Taghit If either a S12XCPU or XGATE taghit occurs a transition to another state sequencer state is initiated and the corresponding DBGSR flags are set. For a comparator related taghit to occur, the S12XDBG must first generate tags based on comparator matches. When the tagged instruction reaches the execution stage of the instruction queue a taghit is generated by the S12XCPU/XGATE. The state control register for the current state determines the next state for each trigger. 20.4.3.3 External Tagging Trigger In external tagging trigger mode, the TAGLO and TAGHI pins (mapped to device pins) are used to tag an instruction. This function can be used as another breakpoint source. When the tagged opcode reaches the MC9S12XDP512 Data Sheet, Rev. 2.21 772 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module execution stage of the instruction queue a transition to the disarmed state0 occurs, ending the debug session and generating a breakpoint, if breakpoints are enabled. External tagging is only possible in device emulation modes. 20.4.3.4 Trigger On XGATE S/W Breakpoint Request The XGATE S/W breakpoint request issues a forced breakpoint request to the S12XCPU immediately independent of S12XDBG settings and triggers the state sequencer into the disarmed state. Active tracing sessions are terminated immediately, thus if tracing has not yet begun, no trace information is stored. XGATE generated breakpoints are independent of the DBGBRK bits. The XGSBPE bit in DBGC1 determines if the XGATE S/W breakpoint function is enabled. The BDM bit in DBGC1 determines if the XGATE requested breakpoint causes the system to enter BDM Mode or initiate a software interrupt (SWI). 20.4.3.5 Immediate Trigger Independent of comparator matches or external tag signals it is possible to initiate a tracing session and/or breakpoint by writing to the TRIG bit in DBGC1. This triggers the state sequencer into the Final State and issues a forced breakpoint request to both S12XCPU and XGATE. 20.4.3.6 Trigger Priorities In case of simultaneous triggers, the priority is resolved according to Table 20-38. The lower priority trigger is suppressed. It is thus possible to miss a lower priority trigger if it occurs simultaneously with a trigger of a higher priority. The trigger priorities described in Table 20-38 dictate that in the case of simultaneous matches, the match on the lower channel number (0,1,2,3) has priority. The SC[3:0] encoding ensures that a match leading to final state has priority over all other matches independent of current state sequencer state. When configured for range modes a simultaneous match of comparators A and C generates an active match0 whilst match2 is suppressed. Table 20-38. Trigger Priorities Priority Source Action Highest XGATE Immediate forced breakpoint......(Tracing terminated immediately). TRIG Enter Final State External TAGHI/TAGLO Enter State0 Match0 (force or tag hit) Trigger to next state as defined by state control registers Match1 (force or tag hit) Trigger to next state as defined by state control registers Match2 (force or tag hit) Trigger to next state as defined by state control registers Match3 (force or tag hit) Trigger to next state as defined by state control registers Lowest MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 773 Chapter 20 S12X Debug (S12XDBGV3) Module 20.4.4 State Sequence Control ARM = 0 State 0 (Disarmed) ARM = 1 State1 State2 ARM = 0 Session Complete (Disarm) Final State State3 ARM = 0 Figure 20-23. State Sequencer Diagram The state sequencer allows a defined sequence of events to provide a trigger point for tracing of data in the trace buffer. Once the S12XDBG module has been armed by setting the ARM bit in the DBGC1 register, then state1 of the state sequencer is entered. Further transitions between the states are then controlled by the state control registers and depend upon a selected trigger mode condition being met. From Final State the only permitted transition is back to the disarmed state0. Transition between any of the states 1 to 3 is not restricted. Each transition updates the SSF[2:0] flags in DBGSR accordingly to indicate the current state. Alternatively writing to the TRIG bit in DBGSC1, the Final State is entered and tracing starts immediately if the TSOURCE bits are configured for tracing. A tag hit through TAGHI/TAGLO brings the state sequencer immediately into state0, causes a breakpoint, if breakpoints are enabled, and ends tracing immediately independent of the trigger alignment bits TALIGN[1:0]. Independent of the state sequencer, each comparator channel can be individually configured to generate an immediate breakpoint when a match occurs through the use of the BRK bits in the DBGxCTL registers. Thus it is possible to generate an immediate breakpoint on selected channels, whilst a state sequencer transition can be initiated by a match on other channels. If a debug session is ended by a trigger on a channel with BRK = 1, the state sequencer transitions through Final State for a clock cycle to state0. This is independent of tracing and breakpoint activity, thus with tracing and breakpoints disabled, the state sequencer enters state0 and the debug module is disarmed. An XGATE S/W breakpoint request, if enabled causes a transition to the State0 and generates a breakpoint request to the S12XCPU immediately. 20.4.4.1 Final State On entering Final State a trigger may be issued to the trace buffer according to the trace position control as defined by the TALIGN field (see Section 20.3.2.3"). If the TSOURCE bits in the trace control register DBGTCR are cleared then the trace buffer is disabled and the transition to Final State can only generate a breakpoint request. In this case or upon completion of a tracing session when tracing is enabled, the ARM MC9S12XDP512 Data Sheet, Rev. 2.21 774 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module bit in the DBGC1 register is cleared, returning the module to the disarmed state0. If tracing is enabled a breakpoint request can occur at the end of the tracing session. If neither tracing nor breakpoints are enabled then when the final state is reached it returns automatically to state0 and the debug module is disarmed. 20.4.5 Trace Buffer Operation The trace buffer is a 64 lines deep by 64-bits wide RAM array. The S12XDBG module stores trace information in the RAM array in a circular buffer format. The S12XCPU accesses the RAM array through a register window (DBGTBH:DBGTBL) using 16-bit wide word accesses. After each complete 64-bit trace buffer line is read via the S12XCPU, an internal pointer into the RAM is incremented so that the next read will receive fresh information. Data is stored in the format shown in Table 20-39. After each store the counter register bits DBGCNT[6:0] are incremented. Tracing of S12XCPU activity is disabled when the BDM is active but tracing of XGATE activity is still possible. Reading the trace buffer whilst the BDM is active returns invalid data and the trace buffer pointer is not incremented. 20.4.5.1 Trace Trigger Alignment Using the TALIGN bits (see Section 20.3.2.3") it is possible to align the trigger with the end, the middle, or the beginning of a tracing session. If End or Mid tracing is selected, tracing begins when the ARM bit in DBGC1 is set and State1 is entered. The transition to Final State if End is selected signals the end of the tracing session. The transition to Final State if Mid is selected signals that another 32 lines will be traced before ending the tracing session. Tracing with Begin-Trigger starts at the opcode of the trigger. Using End or Mid-Trigger or when the tracing is initiated by writing to the TRIG bit whilst configured for Begin-Trigger, tracing starts at the second opcode after writing to DBGC1 if written in the CPU thread, . 20.4.5.1.1 Storing with Begin-Trigger Storing with Begin-Trigger, data is not stored in the Trace Buffer until the Final State is entered. Once the trigger condition is met the S12XDBG module will remain armed until 64 lines are stored in the Trace Buffer. If the trigger is at the address of the change-of-flow instruction the change of flow associated with the trigger will be stored in the Trace Buffer. Using Begin-trigger together with tagging, if the tagged instruction is about to be executed then the trace is started. Upon completion of the tracing session the breakpoint is generated, thus the breakpoint does not occur at the tagged instruction boundary. 20.4.5.1.2 Storing with Mid-Trigger Storing with Mid-Trigger, data is stored in the Trace Buffer as soon as the S12XDBG module is armed. When the trigger condition is met, another 32 lines will be traced before ending the tracing session, irrespective of the number of lines stored before the trigger occurred, then the S12XDBG module is disarmed and no more data is stored. If the trigger is at the address of a change of flow instruction the trigger event is not stored in the Trace Buffer. Using Mid-trigger with tagging, if the tagged instruction is about to be executed then the trace is continued for another 32 lines. Upon tracing completion the breakpoint is generated, thus the breakpoint does not occur at the tagged instruction boundary. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 775 Chapter 20 S12X Debug (S12XDBGV3) Module 20.4.5.1.3 Storing with End-Trigger Storing with End-Trigger, data is stored in the Trace Buffer until the Final State is entered, at which point the S12XDBG module will become disarmed and no more data will be stored. If the trigger is at the address of a change of flow instruction the trigger event will not be stored in the Trace Buffer. 20.4.5.2 Trace Modes The S12XDBG module can operate in four trace modes. The mode is selected using the TRCMOD bits in the DBGTCR register. In each mode tracing of XGATE or S12XCPU information is possible. The source for the trace is selected using the TSOURCE bits in the DBGTCR register. The modes are described in the following subsections. The trace buffer organization is shown in Table 20-39. 20.4.5.2.1 Normal Mode In Normal Mode, change of flow (COF) program counter (PC) addresses will be stored. COF addresses are defined as follows for the S12XCPU: * Source address of taken conditional branches (long, short, bit-conditional, and loop primitives) * Destination address of indexed JMP, JSR, and CALL instruction. * Destination address of RTI, RTS, and RTC instructions * Vector address of interrupts, except for SWI and BDM vectors LBRA, BRA, BSR, BGND as well as non-indexed JMP, JSR, and CALL instructions are not classified as change of flow and are not stored in the trace buffer. COF addresses are defined as follows for the XGATE: * Source address of taken conditional branches * Destination address of indexed JAL instructions. * First XGATE code address in a thread Change-of-flow addresses stored include the full 23-bit address bus in the case of S12XCPU, the 16-bit address bus for the XGATE module and an information byte, which contains a source/destination bit to indicate whether the stored address was a source address or destination address. 20.4.5.2.2 Loop1 Mode Loop1 Mode, similarly to Normal Mode also stores only COF address information to the trace buffer, it however allows the filtering out of redundant information. The intent of Loop1 Mode is to prevent the Trace Buffer from being filled entirely with duplicate information from a looping construct such as delays using the DBNE instruction or polling loops using BRSET/BRCLR instructions. Immediately after address information is placed in the Trace Buffer, the S12XDBG module writes this value into a background register. This prevents consecutive duplicate address entries in the Trace Buffer resulting from repeated branches. MC9S12XDP512 Data Sheet, Rev. 2.21 776 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module Loop1 Mode only inhibits consecutive duplicate source address entries that would typically be stored in most tight looping constructs. It does not inhibit repeated entries of destination addresses or vector addresses, since repeated entries of these would most likely indicate a bug in the user's code that the S12XDBG module is designed to help find. NOTE In certain very tight loops, the source address will have already been fetched again before the background comparator is updated. This results in the source address being stored twice before further duplicate entries are suppressed. This condition occurs with branch-on-bit instructions when the branch is fetched by the first P-cycle of the branch or with loop-construct instructions in which the branch is fetched with the first or second P cycle. See examples below: LOOP LOOP2 INX BRCLR BRN NOP DBNE 20.4.5.2.3 CMPTMP,#$0c, LOOP * A,LOOP2 ; 1-byte instruction fetched by 1st P-cycle of BRCLR ; the BRCLR instruction also will be fetched by 1st ; P-cycle of BRCLR ; 2-byte instruction fetched by 1st P-cycle of DBNE ; 1-byte instruction fetched by 2nd P-cycle of DBNE ; this instruction also fetched by 2nd P-cycle of DBNE Detail Mode In Detail Mode, address and data for all memory and register accesses is stored in the trace buffer. In the case of XGATE tracing this means that initialization of the R1 register during a vector fetch is not traced. This mode is intended to supply additional information on indexed, indirect addressing modes where storing only the destination address would not provide all information required for a user to determine where the code is in error. This mode also features information byte storage to the trace buffer, for each address byte storage. The information byte indicates the size of access (word or byte), the type of access (read or write). When tracing S12XCPU activity in Detail Mode, all cycles are traced except those when the S12XCPU is either in a free or opcode fetch cycle. In this mode the XGATE program counter is also traced to provide a snapshot of the XGATE activity. CXINF information byte bits indicate the type of XGATE activity occurring at the time of the trace buffer entry. When tracing S12XCPU activity alone in Detail Mode, the address range can be limited to a range specified by the TRANGE bits in DBGTCR. This function uses comparators C and D to define an address range inside which S12XCPU activity should be traced (see Table 20-39). Thus the traced S12XCPU activity can be restricted to register range accesses. When tracing XGATE activity in Detail Mode, all load and store cycles are traced. Additionally the S12XCPU program counter is stored at the time of the XGATE trace buffer entry to provide a snapshot of S12XCPU activity. 20.4.5.2.4 Pure PC Mode In Pure PC Mode, tracing from the CPU the PC addresses of all executed opcodes are stored with the exception of WAI and STOP instructions. In Pure PC Mode, tracing from the XGATE the PC addresses of all executed opcodes are stored. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 777 Chapter 20 S12X Debug (S12XDBGV3) Module 20.4.5.3 Trace Buffer Organization The buffer can be used to trace either from S12XCPU, from XGATE or from both sources. An X prefix denotes information from the XGATE module, a C prefix denotes information from the S12XCPU. ADRH, ADRM, ADRL denote address high, middle and low byte respectively. INF bytes contain control information (R/W, S/D etc.). The numerical suffix indicates which tracing step. The information format for Loop1 Mode is the same as that of Normal Mode. Whilst tracing from XGATE or S12XCPU only, in Normal or Loop1 modes each array line contains data from entries made at two separate times, thus in this case the DBGCNT[0] is incremented after each separate entry. In all other modes DBGCNT[0] remains cleared whilst the other DBGCNT bits are incremented on each trace buffer entry. XGATE and S12XCPU COFs occur independently of each other and the profile of COFs for the two sources is totally different. When both sources are being traced in Normal or Loop1 mode, for each COF from one source, there may be many COFs from the other source, depending on user code. COF events could occur far from each other in the time domain, on consecutive cycles or simultaneously. When a COF occurs in either source (S12X or XGATE) a trace buffer entry is made and the corresponding CDV or XDV bit is set. The current PC of the other source is simultaneously stored to the trace buffer even if no COF has occurred, in which case CDV/XDV remains cleared indicating the address is not associated with a COF, but is simply a snapshot of the PC contents at the time of the COF from the other source. Single byte data accesses in Detail Mode are always stored to the low byte of the trace buffer (CDATAL or XDATAL) and the high byte is cleared. When tracing word accesses, the byte at the lower address is always stored to trace buffer byte3 and the byte at the higher address is stored to byte2 Table 20-39. Trace Buffer Organization Mode 8-Byte Wide Word Buffer 7 6 5 4 3 2 1 0 XGATE Detail CXINF1 CADRH1 CADRM1 CADRL1 XDATAH1 XDATAL1 XADRM1 XADRL1 CXINF2 CADRH2 CADRM2 CADRL2 XDATAH2 XDATAL2 XADRM2 XADRL2 S12XCPU Detail CXINF1 CADRH1 CADRM1 CADRL1 CDATAH1 CDATAL1 XADRM1 XADRL1 CXINF2 CADRH2 CADRM2 CADRL2 CDATAH2 CDATAL2 XADRM2 XADRL2 Both Other Modes XINF0 XPCM0 XPCL0 CINF0 CPCH0 CPCM0 CPCL0 XINF1 XPCM1 XPCL1 CINF1 CPCH1 CPCM1 CPCL1 XINF1 XPCM1 XPCL1 XINF0 XPCM0 XPCL0 XINF3 XPCM3 XPCL3 XINF2 XPCM2 XPCL2 XGATE Other Modes S12XCPU Other Modes CINF1 CPCH1 CPCM1 CPCL1 CINF0 CPCH0 CPCM0 CPCL0 CINF3 CPCH3 CPCM3 CPCL3 CINF2 CPCH2 CPCM2 CPCL2 MC9S12XDP512 Data Sheet, Rev. 2.21 778 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.4.5.3.1 Information Byte Organization The format of the control information byte for both S12XCPU and XGATE modules is dependent upon the active trace mode and tracing source as described below. In Normal, Loop1, or Pure PC modes tracing of XGATE activity, XINF is used to store control information. In Normal, Loop1, or Pure PC modes tracing of S12XCPU activity, CINF is used to store control information. In Detail Mode, CXINF contains the control information XGATE Information Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 XSD XSOT XCOT XDV 0 0 0 0 Figure 20-24. XGATE Information Byte XINF Table 20-40. XINF Field Descriptions Field Description 7 XSD Source Destination Indicator -- This bit indicates if the corresponding stored address is a source or destination address. This is only used in Normal and Loop1 mode tracing. 0 Source Address 1 Destination Address or Start of Thread or Continuation of Thread 6 XSOT Source Of Thread Indicator -- This bit indicates that the corresponding stored address is a start of thread address. This is only used in Normal and Loop1 mode tracing. NOTE. This bit only has effect on devices where the XGATE module supports multiple interrupt levels. 0 Stored address not from a start of thread 1 Stored address from a start of thread 5 XCOT Continuation Of Thread Indicator -- This bit indicates that the corresponding stored address is the first address following a return from a higher priority thread. This is only used in Normal and Loop1 mode tracing. NOTE. This bit only has effect on devices where the XGATE module supports multiple interrupt levels. 0 Stored address not from a continuation of thread 1 Stored address from a continuation of thread 4 XDV Data Invalid Indicator -- This bit indicates if the trace buffer entry is invalid. It is only used when tracing from both sources in Normal, Loop1 and Pure PC modes, to indicate that the XGATE trace buffer entry is valid. 0 Trace buffer entry is invalid 1 Trace buffer entry is valid X12X_CPU Information Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CSD CVA 0 CDV 0 0 0 0 Figure 20-25. S12XCPU Information Byte CINF MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 779 Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-41. CINF Field Descriptions Field Description 7 CSD Source Destination Indicator -- This bit indicates if the corresponding stored address is a source or destination address. This is only used in Normal and Loop1 mode tracing. 0 Source Address 1 Destination Address 6 CVA Vector Indicator -- This bit indicates if the corresponding stored address is a vector address.. This is only used in Normal and Loop1 mode tracing. 0 Source Address 1 Destination Address 4 CDV Data Invalid Indicator -- This bit indicates if the trace buffer entry is invalid. It is only used when tracing from both sources in Normal, Loop1 and Pure PC modes, to indicate that the S12XCPU trace buffer entry is valid. 0 Trace buffer entry is invalid 1 Trace buffer entry is valid CXINF Information Byte Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 CFREE CSZ CRW COCF XACK XSZ XRW XOCF Figure 20-26. Information Byte CXINF This describes the format of the information byte used only when tracing from S12XCPU or XGATE in Detail Mode. When tracing from the S12XCPU in Detail Mode, information is stored to the trace buffer on all cycles except opcode fetch and free cycles. The XGATE entry stored on the same line is a snapshot of the XGATE program counter. In this case the CSZ and CRW bits indicate the type of access being made by the S12XCPU, whilst the XACK and XOCF bits indicate if the simultaneous XGATE cycle is a free cycle (no bus acknowledge) or opcode fetch cycle. Similarly when tracing from the XGATE in Detail Mode, information is stored to the trace buffer on all cycles except opcode fetch and free cycles. The S12XCPU entry stored on the same line is a snapshot of the S12XCPU program counter. In this case the XSZ and XRW bits indicate the type of access being made by the XGATE, whilst the CFREE and COCF bits indicate if the simultaneous S12XCPU cycle is a free cycle or opcode fetch cycle. Table 20-42. CXINF Field Descriptions Field Description 7 CFREE S12XCPU Free Cycle Indicator -- This bit indicates if the stored S12XCPU address corresponds to a free cycle. This bit only contains valid information when tracing the XGATE accesses in Detail Mode. 0 Stored information corresponds to free cycle 1 Stored information does not correspond to free cycle 6 CSZ Access Type Indicator -- This bit indicates if the access was a byte or word size access.This bit only contains valid information when tracing S12XCPU activity in Detail Mode. 0 Word Access 1 Byte Access MC9S12XDP512 Data Sheet, Rev. 2.21 780 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-42. CXINF Field Descriptions (continued) Field Description 5 CRW Read Write Indicator -- This bit indicates if the corresponding stored address corresponds to a read or write access. This bit only contains valid information when tracing S12XCPU activity in Detail Mode. 0 Write Access 1 Read Access 4 COCF S12XCPU Opcode Fetch Indicator -- This bit indicates if the stored address corresponds to an opcode fetch cycle. This bit only contains valid information when tracing the XGATE accesses in Detail Mode. 0 Stored information does not correspond to opcode fetch cycle 1 Stored information corresponds to opcode fetch cycle 3 XACK XGATE Access Indicator -- This bit indicates if the stored XGATE address corresponds to a free cycle. This bit only contains valid information when tracing the S12XCPU accesses in Detail Mode. 0 Stored information corresponds to free cycle 1 Stored information does not correspond to free cycle 2 XSZ Access Type Indicator -- This bit indicates if the access was a byte or word size access. This bit only contains valid information when tracing XGATE activity in Detail Mode. 0 Word Access 1 Byte Access 1 XRW Read Write Indicator -- This bit indicates if the corresponding stored address corresponds to a read or write access. This bit only contains valid information when tracing XGATE activity in Detail Mode. 0 Write Access 1 Read Access 0 XOCF XGATE Opcode Fetch Indicator -- This bit indicates if the stored address corresponds to an opcode fetch cycle.This bit only contains valid information when tracing the S12XCPU accesses in Detail Mode. 0 Stored information does not correspond to opcode fetch cycle 1 Stored information corresponds to opcode fetch cycle 20.4.5.4 Reading Data from Trace Buffer The data stored in the Trace Buffer can be read using either the background debug module (BDM) module or the S12XCPU provided the S12XDBG module is not armed, is configured for tracing (at least one TSOURCE bit is set) and the system not secured. When the ARM bit is written to 1 the trace buffer is locked to prevent reading. The trace buffer can only be unlocked for reading by a single aligned word write to DBGTB when the module is disarmed. Multiple writes to the DBGTB are not allowed since they increment the pointer. The Trace Buffer can only be read through the DBGTB register using aligned word reads, any byte or misaligned reads return 0 and do not cause the trace buffer pointer to increment to the next trace buffer address. The Trace Buffer data is read out first-in first-out. By reading CNT in DBGCNT the number of valid 64-bit lines can be determined. DBGCNT will not decrement as data is read. Whilst reading an internal pointer is used to determine the next line to be read. After a tracing session, the pointer points to the oldest data entry, thus if no overflow has occurred, the pointer points to line0, otherwise it points to the line with the oldest entry. The pointer is initialized by each aligned write to DBGTBH to point to the oldest data again. This enables an interrupted trace buffer read sequence to be easily restarted from the oldest data entry. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 781 Chapter 20 S12X Debug (S12XDBGV3) Module The least significant word of each 64-bit wide array line is read out first. This corresponds to the bytes 1 and 0 of Table 20-39. The bytes containing invalid information (shaded in Table 20-39) are also read out. Reading the Trace Buffer while the S12XDBG module is armed will return invalid data and no shifting of the RAM pointer will occur. Reading the trace buffer is not possible if both TSOURCE bits are cleared. 20.4.5.5 Trace Buffer Reset State The Trace Buffer contents are not initialized by a system reset. Thus should a system reset occur, the trace session information from immediately before the reset occurred can be read out. The DBGCNT bits are not cleared by a system reset. Thus should a reset occur, the number of valid lines in the trace buffer is indicated by DBGCNT. The internal pointer to the current trace buffer address is initialized by unlocking the trace buffer thus points to the oldest valid data even if a reset occurred during the tracing session. Generally debugging occurrences of system resets is best handled using mid or end trigger alignment since the reset may occur before the trace trigger, which in the begin trigger alignment case means no information would be stored in the trace buffer. 20.4.6 Tagging A tag follows program information as it advances through the instruction queue. When a tagged instruction reaches the head of the queue a tag hit occurs and triggers the state sequencer. Each comparator control register features a TAG bit, which controls whether the comparator match will cause a trigger immediately or tag the opcode at the matched address. If a comparator is enabled for tagged comparisons, the address stored in the comparator match address registers must be an opcode address for the trigger to occur. Both S12XCPU and XGATE opcodes can be tagged with the comparator register TAG bits. Using Begin trigger together with tagging, if the tagged instruction is about to be executed then the transition to the next state sequencer state occurs. If the transition is to the Final State, tracing is started. Only upon completion of the tracing session can a breakpoint be generated. Similarly using Mid trigger with tagging, if the tagged instruction is about to be executed then the trace is continued for another 32 lines. Upon tracing completion the breakpoint is generated. Using End trigger, when the tagged instruction is about to be executed and the next transition is to Final State then a breakpoint is generated immediately, before the tagged instruction is carried out. R/W monitoring is not useful for tagged operations since the trigger occurs based on the tagged opcode reaching the execution stage of the instruction queue. Similarly access size (SZ) monitoring and data bus monitoring is not useful if tagged triggering is selected, since the tag is attached to the opcode at the matched address and is not dependent on the data bus nor on the size of access. Thus these bits are ignored if tagged triggering is selected. When configured for range comparisons and tagging, the ranges are accurate only to word boundaries. S12X tagging is disabled when the BDM becomes active. Conversely BDM firmware commands are not processed while tagging is active. XGATE tagging is possible when the BDM is active. MC9S12XDP512 Data Sheet, Rev. 2.21 782 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.4.6.1 External Tagging using TAGHI and TAGLO External tagging using the external TAGHI and TAGLO pins can only be used to tag S12XCPU opcodes; tagging of XGATE code using these pins is not possible. An external tag triggers the state sequencer into state0 when the tagged opcode reaches the execution stage of the instruction queue. The pins operate independently, thus the state of one pin does not affect the function of the other. External tagging is possible in emulation modes only. The presence of logic level 0 on either pin at the rising edge of the external clock (ECLK) performs the function indicated in the Table 20-43. It is possible to tag both bytes of an instruction word. If a taghit occurs, a breakpoint can be generated as defined by the DBGBRK and BDM bits in DBGC1. Each time TAGHI or TAGLO are low on the rising edge of ECLK, the old tag is replaced by a new one. Table 20-43. Tag Pin Function TAGHI 1 1 0 0 20.4.6.2 TAGLO 1 0 1 0 Tag No tag Low byte High byte Both bytes Unconditional Tagging Function In emulation modes a low assertion of PE5/TAGLO/MODA in the 7th or 8th bus cycle after reset enables the unconditional tagging function, allowing immediate tagging via TAGHI/TAGLO with breakpoint to BDM independent of the ARM, BDM and DBGBRK bits. Conversely these bits are not affected by unconditional tagging. The unconditional tagging function remains enabled until the next reset. This function allows an immediate entry to BDM in emulation modes before user code execution. The TAGLO assertion must be in the 7th or 8th bus cycle following the end of reset, whereby the prior RESET pin assertion lasts the full 192 bus cycles. 20.4.7 Breakpoints There are several ways to generate breakpoints to the XGATE and S12XCPU modules * Through XGATE software breakpoint requests. * From comparator channel triggers to final state. * Using software to write to the TRIG bit in the DBGC1 register. * From taghits generated using the external TAGHI and TAGLO pins. * Through the auxilliary forced breakpoint input. 20.4.7.1 XGATE Software Breakpoints The XGATE software breakpoint instruction BRK can request an S12XCPU breakpoint, via the S12XDBG module. In this case, if the XGSBPE bit is set, the S12XDBG module immediately generates a forced breakpoint request to the S12XCPU, the state sequencer is returned to state0 and tracing, if active, is terminated. If configured for BEGIN trigger and tracing has not yet been triggered from another source, the trace buffer contains no information. Breakpoint requests from the XGATE module do not depend MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 783 Chapter 20 S12X Debug (S12XDBGV3) Module upon the state of the DBGBRK or ARM bits in DBGC1. They depend solely on the state of the XGSBPE and BDM bits. Thus it is not necessary to ARM the DBG module to use XGATE software breakpoints to generate breakpoints in the S12XCPU program flow, but it is necessary to set XGSBPE. Furthermore, if a breakpoint to BDM is required, the BDM bit must also be set. When the XGATE requests an S12XCPU breakpoint, the XGATE program flow stops by default, independent of the S12XDBG module. 20.4.7.2 Breakpoints From Internal Comparator Channel Final State Triggers Breakpoints can be generated when internal comparator channels trigger the state sequencer to the Final State. If configured for tagging, then the breakpoint is generated when the tagged opcode reaches the execution stage of the instruction queue. If a tracing session is selected by the TSOURCE bits, breakpoints are requested when the tracing session has completed, thus if Begin or Mid aligned triggering is selected, the breakpoint is requested only on completion of the subsequent trace (see Table 20-44). If no tracing session is selected, breakpoints are requested immediately. If the BRK bit is set on the triggering channel, then the breakpoint is generated immediately independent of tracing trigger alignment. Table 20-44. Breakpoint Setup For Both XGATE and S12XCPU Breakpoints BRK TALIGN DBGBRK[n] Breakpoint Alignment 0 00 0 Fill Trace Buffer until trigger (no breakpoints -- keep running) 0 00 1 Fill Trace Buffer until trigger, then breakpoint request occurs 0 01 0 Start Trace Buffer at trigger (no breakpoints -- keep running) 0 01 1 Start Trace Buffer at trigger A breakpoint request occurs when Trace Buffer is full 0 10 0 Store a further 32 Trace Buffer line entries after trigger (no breakpoints -- keep running) 0 10 1 Store a further 32 Trace Buffer line entries after trigger Request breakpoint after the 32 further Trace Buffer entries 1 00,01,10 1 Terminate tracing and generate breakpoint immediately on trigger 1 00,01,10 0 Terminate tracing immediately on trigger x 11 x Reserved 20.4.7.3 Breakpoints Generated Via The TRIG Bit If a TRIG triggers occur, the Final State is entered. Tracing trigger alignment is defined by the TALIGN bits. If a tracing session is selected by the TSOURCE bits, breakpoints are requested when the tracing session has completed, thus if Begin or Mid aligned triggering is selected, the breakpoint is requested only on completion of the subsequent trace (see Table 20-44). If no tracing session is selected, breakpoints are requested immediately. TRIG breakpoints are possible even if the S12XDBG module is disarmed. MC9S12XDP512 Data Sheet, Rev. 2.21 784 Freescale Semiconductor Chapter 20 S12X Debug (S12XDBGV3) Module 20.4.7.4 Breakpoints Via TAGHI Or TAGLO Pin Taghits Tagging using the external TAGHI/TAGLO pins always ends the session immediately at the tag hit. It is always end aligned, independent of internal channel trigger alignment configuration. 20.4.7.5 Auxilliary Breakpoint Input When this signal asserts tracing is terminated and an immediate forced breakpoints are generated, depending on the configuration of DBGBRK bits. 20.4.7.6 S12XDBG Breakpoint Priorities XGATE software breakpoints have the highest priority. Active tracing sessions are terminated immediately. If a TRIG trigger occurs after Begin or Mid aligned tracing has already been triggered by a comparator instigated transition to Final State, then TRIG no longer has an effect. When the associated tracing session is complete, the breakpoint occurs. Similarly if a TRIG is followed by a subsequent trigger from a comparator channel whose BRK = 0, it has no effect, since tracing has already started. If a comparator tag hit occurs simultaneously with an external TAGHI/TAGLO hit, the state sequencer enters state0. TAGHI/TAGLO triggers are always end aligned, to end tracing immediately, independent of the tracing trigger alignment bits TALIGN[1:0]. If a forced and tagged breakpoint coincide, the forced breakpoint occurs too late to prevent the tagged instruction being loaded into the execution unit. Conversely the taghit is too late to prevent the breakpoint request in the DBG module. Thus the S12XCPU suppresses the taghit although the tagged instruction is executed. Considering the code example below the forced breakpoint is requested when the location COUNTER is accessed. This is signalled to the S12XCPU when the next (tagged) instruction (NOP) is already in the execution stage, thus the tagged instruction is carried out but the tagged breakpoint is suppressed. Reading the PC with BDM READ_PC returns $C008 c000 c003 c004 c007 00 [BDM c008 cf ff 00 a7 72 70 08 a7 START MARK firmware commands] 20 01 20.4.7.6.1 LDS NOP INC NOP BGND BRA #$FF00 COUNTER ; Forced breakpoint location = COUNTER ; Tagged opcode location = MARK END ; 1st instruction on return from BDM S12XDBG Breakpoint Priorities And BDM Interfacing Breakpoint operation is dependent on the state of the S12XBDM module. If the S12XBDM module is active, the S12XCPU is executing out of BDM firmware and S12X breakpoints are disabled. In addition, while executing a BDM TRACE command, tagging into BDM is disabled. If BDM is not active, the breakpoint will give priority to BDM requests over SWI requests if the breakpoint happens to coincide with a SWI instruction in the user's code. On returning from BDM, the SWI from user code gets executed. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 785 Chapter 20 S12X Debug (S12XDBGV3) Module Table 20-45. Breakpoint Mapping Summary DBGBRK[1] (DBGC1[3]) BDM Bit (DBGC1[4]) BDM Enabled BDM Active S12X Breakpoint Mapping 0 X X X No Breakpoint 1 0 X 0 Breakpoint to SWI 1 0 X 1 No Breakpoint 1 1 0 X Breakpoint to SWI 1 1 1 0 Breakpoint to BDM 1 1 1 1 No Breakpoint BDM cannot be entered from a breakpoint unless the ENABLE bit is set in the BDM. If entry to BDM via a BGND instruction is attempted and the ENABLE bit in the BDM is cleared, the S12XCPU actually executes the BDM firmware code. It checks the ENABLE and returns if ENABLE is not set. If not serviced by the monitor then the breakpoint is re-asserted when the BDM returns to normal S12XCPU flow. If the comparator register contents coincide with the SWI/BDM vector address then an SWI in user code and DBG breakpoint could occur simultaneously. The S12XCPU ensures that BDM requests have a higher priority than SWI requests. Returning from the BDM/SWI service routine care must be taken to avoid re triggering a breakpoint. NOTE When program control returns from a tagged breakpoint using an RTI or BDM GO command without program counter modification it will return to the instruction whose tag generated the breakpoint. To avoid re triggering a breakpoint at the same location reconfigure the S12XDBG module in the SWI routine, if configured for an SWI breakpoint, or over the BDM interface by executing a TRACE command before the GO to increment the program flow past the tagged instruction. An XGATE software breakpoint is forced immediately, the tracing session terminated and the XGATE module execution stops. The user can thus determine if an XGATE breakpoint has occurred by reading out the XGATE program counter over the BDM interface. MC9S12XDP512 Data Sheet, Rev. 2.21 786 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.1 Introduction This document describes the functionality of the XEBI block controlling the external bus interface. The XEBI controls the functionality of a non-multiplexed external bus (a.k.a. `expansion bus') in relationship with the chip operation modes. Dependent on the mode, the external bus can be used for data exchange with external memory, peripherals or PRU, and provide visibility to the internal bus externally in combination with an emulator. 21.1.1 Features The XEBI includes the following features: * Output of up to 23-bit address bus and control signals to be used with a non-muxed external bus * Bidirectional 16-bit external data bus with option to disable upper half * Visibility of internal bus activity 21.1.2 * * * Modes of Operation Single-chip modes The external bus interface is not available in these modes. Expanded modes Address, data, and control signals are activated on the external bus in normal expanded mode and special test mode. Emulation modes The external bus is activated to interface to an external tool for emulation of normal expanded mode or normal single-chip mode applications. Refer to the S12X_MMC section for a detailed description of the MCU operating modes. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 787 Chapter 21 External Bus Interface (S12XEBIV2) 21.1.3 Block Diagram Figure 21-1 is a block diagram of the XEBI with all related I/O signals. ADDR[22:0] DATA[15:0] IVD[15:0] LSTRB R/W EWAIT XEBI UDS LDS RE WE ACC[2:0] IQSTAT[3:0] Figure 21-1. XEBI Block Diagram 21.2 External Signal Description The user is advised to refer to the SoC section for port configuration and location of external bus signals. NOTE The following external bus related signals are described in other sections: CS2, CS1, CS0 (chip selects) -- S12X_MMC section ECLK, ECLKX2 (free-running clocks) -- PIM section TAGHI, TAGLO (tag inputs) -- PIM section, S12X_DBG section Table 21-1 outlines the pin names and gives a brief description of their function. Refer to the SoC section and PIM section for reset states of these pins and associated pull-ups or pull-downs. MC9S12XDP512 Data Sheet, Rev. 2.21 788 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) Table 21-1. External System Signals Associated with XEBI Signal 1 I /O EBI Signal Multiplex (T)ime2 (F)unction3 Available in Modes Description NS SS NX ES EX ST RE O -- -- Read Enable, indicates external read access No No Yes No No No ADDR[22:20] O T -- External address No No Yes Yes Yes Yes ACC[2:0] O -- Access source No No No Yes Yes Yes ADDR[19:16] O -- External address No No Yes Yes Yes Yes IQSTAT[3:0] O -- Instruction Queue Status No No No Yes Yes Yes ADDR[15:1] O -- External address No No Yes Yes Yes Yes IVD[15:1] O -- Internal visibility read data (IVIS = 1) No No No Yes Yes Yes ADDR0 O F External address No No No Yes Yes Yes IVD0 O Internal visibility read data (IVIS = 1) No No No Yes Yes Yes UDS O -- Upper Data Select, indicates external access to the high byte DATA[15:8] No No Yes No No No LSTRB O -- Low Strobe, indicates valid data on DATA[7:0] No No No Yes Yes Yes LDS O -- Lower Data Select, indicates external access to the low byte DATA[7:0] No No Yes No No No R/W O -- Read/Write, indicates the direction of internal data transfers No No No Yes Yes Yes WE O -- Write Enable, indicates external write access No No Yes No No No DATA[15:8] I/O -- -- Bidirectional data (even address) No No Yes Yes Yes Yes DATA[7:0] I/O -- -- Bidirectional data (odd address) No No Yes Yes Yes Yes I -- -- External control for external bus access stretches (adding wait states) No No Yes No Yes No EWAIT T T T F F 1 All inputs are capable of reducing input threshold level Time-multiplex means that the respective signals share the same pin on chip level and are active alternating in a dedicated time slot (in modes where applicable). 3 Function-multiplex means that one of the respective signals sharing the same pin on chip level continuously uses the pin depending on configuration and reset state. 2 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 789 Chapter 21 External Bus Interface (S12XEBIV2) 21.3 Memory Map and Register Definition This section provides a detailed description of all registers accessible in the XEBI. 21.3.1 Module Memory Map The registers associated with the XEBI block are shown in Figure 21-2. Register Name EBICTL0 Bit 7 R W EBICTL1 R W ITHRS EWAITE 6 0 5 4 3 2 1 Bit 0 HDBE ASIZ4 ASIZ3 ASIZ2 ASIZ1 ASIZ0 0 0 0 EXSTR2 EXSTR1 EXSTR0 0 = Unimplemented or Reserved Figure 21-2. XEBI Register Summary 21.3.2 Register Descriptions The following sub-sections provide a detailed description of each register and the individual register bits. All control bits can be written anytime, but this may have no effect on the related function in certain operating modes. This allows specific configurations to be set up before changing into the target operating mode. NOTE Depending on the operating mode an available function may be enabled, disabled or depend on the control register bit. Reading the register bits will reflect the status of related function only if the current operating mode allows user control. Please refer the individual bit descriptions. MC9S12XDP512 Data Sheet, Rev. 2.21 790 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.3.2.1 External Bus Interface Control Register 0 (EBICTL0) 7 R W Reset 6 0 ITHRS 0 0 5 4 3 2 1 0 HDBE ASIZ4 ASIZ3 ASIZ2 ASIZ1 ASIZ0 1 1 1 1 1 1 = Unimplemented or Reserved Figure 21-3. External Bus Interface Control Register 0 (EBICTL0) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes, the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. This register controls input pin threshold level and determines the external address and data bus sizes in normal expanded mode. If not in use with the external bus interface, the related pins can be used for alternative functions. External bus is available as programmed in normal expanded mode and always full-sized in emulation modes and special test mode; function not available in single-chip modes. Table 21-2. EBICTL0 Field Descriptions Field Description 7 ITHRS Reduced Input Threshold -- This bit selects reduced input threshold on external data bus pins and specific control input signals which are in use with the external bus interface in order to adapt to external devices with a 3.3 V, 5 V tolerant I/O. The reduced input threshold level takes effect depending on ITHRS, the operating mode and the related enable signals of the EBI pin function as summarized in Table 21-3. 0 Input threshold is at standard level on all pins 1 Reduced input threshold level enabled on pins in use with the external bus interface 5 HDBE High Data Byte Enable -- This bit enables the higher half of the 16-bit data bus. If disabled, only the lower 8-bit data bus can be used with the external bus interface. In this case the unused data pins and the data select signals (UDS and LDS) are free to be used for alternative functions. 0 DATA[15:8], UDS, and LDS disabled 1 DATA[15:8], UDS, and LDS enabled 4-0 ASIZ[4:0] External Address Bus Size -- These bits allow scalability of the external address bus. The programmed value corresponds to the number of available low-aligned address lines (refer to Table 21-4). All address lines ADDR[22:0] start up as outputs after reset in expanded modes. This needs to be taken into consideration when using alternative functions on relevant pins in applications which utilize a reduced external address bus. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 791 Chapter 21 External Bus Interface (S12XEBIV2) Table 21-3. Input Threshold Levels on External Signals ITHRS External Signal NS SS NX Standard Standard Standard DATA[15:8] TAGHI, TAGLO 0 DATA[7:0] EWAIT DATA[15:8] TAGHI, TAGLO 1 Reduced if HDBE = 1 DATA[7:0] Standard Standard EX ST Reduced Reduced Standard Standard Reduced Reduced Reduced Standard Reduced if EWAITE = 1 Standard Standard Reduced Reduced if EWAITE = 1 EWAIT ES Table 21-4. External Address Bus Size ASIZ[4:0] Available External Address Lines 00000 None 00001 UDS 00010 ADDR1, UDS 00011 ADDR[2:1], UDS : : 10110 ADDR[21:1], UDS 10111 : 11111 ADDR[22:1], UDS MC9S12XDP512 Data Sheet, Rev. 2.21 792 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.3.2.2 External Bus Interface Control Register 1 (EBICTL1) 7 R W EWAITE Reset 0 6 5 4 3 0 0 0 0 0 0 0 0 2 1 0 EXSTR2 EXSTR1 EXSTR0 1 1 1 = Unimplemented or Reserved Figure 21-4. External Bus Interface Control Register 1 (EBICTL1) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. This register is used to configure the external access stretch (wait) function. Table 21-5. EBICTL1 Field Descriptions Field Description 7 EWAITE External Wait Enable -- This bit enables the external access stretch function using the external EWAIT input pin. Enabling this feature may have effect on the minimum number of additional stretch cycles (refer to Table 21-6). External wait feature is only active if enabled in normal expanded mode and emulation expanded mode; function not available in all other operating modes. 0 External wait is disabled 1 External wait is enabled 2-0 EXSTR[2:0] External Access Stretch Bits 2, 1, 0 -- This three bit field determines the amount of additional clock stretch cycles on every access to the external address space as shown in Table 21-6. The minimum number of stretch cycles depends on the EWAITE setting. Stretch cycles are added as programmed in normal expanded mode and emulation expanded mode; function not available in all other operating modes. Table 21-6. External Access Stretch Bit Definition Number of Stretch Cycles EXSTR[2:0] EWAITE = 0 EWAITE = 1 000 1 cycle >= 2 cycles 001 2 cycles >= 2 cycles 010 3 cycles >= 3 cycles 011 4 cycles >= 4 cycles 100 5 cycles >= 5 cycles 101 6 cycles >= 6 cycles 110 7 cycles >= 7 cycles 111 8 cycles >= 8 cycles MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 793 Chapter 21 External Bus Interface (S12XEBIV2) 21.4 Functional Description This section describes the functions of the external bus interface. The availability of external signals and functions in relation to the operating mode is initially summarized and described in more detail in separate sub-sections. 21.4.1 Operating Modes and External Bus Properties A summary of the external bus interface functions for each operating mode is shown in Table 21-7. Table 21-7. Summary of Functions Single-Chip Modes Properties (if Enabled) Normal Single-Chip Expanded Modes Special Single-Chip Normal Expanded Emulation Single-Chip Emulation Expanded Special Test 2 cycles read external write int & ext 2 cycles read external write int & ext 2 cycles read internal write internal 1 cycle 1 cycle 1 cycle Timing Properties PRR access 1 2 cycles read internal write internal 2 cycles read internal write internal 2 cycles read internal write internal Internal access visible externally -- -- External address access and unimplemented area access2 -- -- Max. of 2 to 9 programmed cycles or n cycles of ext. wait3 1 cycle Max. of 2 to 9 programmed cycles or n cycles of ext. wait3 1 cycle Flash area address access4 -- -- -- 1 cycle 1 cycle 1 cycle -- Signal Properties ADDR[22:20]/A ADDR[22:20]/A CC[2:0] CC[2:0] ADDR[19:16]/ ADDR[19:16]/ IQSTAT[3:0] IQSTAT[3:0] ADDR[15:0]/ ADDR[15:0]/ IVD[15:0] IVD[15:0] DATA[15:0] DATA[15:0] ADDR[22:0] DATA[15:0] Bus signals -- -- ADDR[22:1] DATA[15:0] Data select signals (if 16-bit data bus) -- -- UDS LDS ADDR0 LSTRB ADDR0 LSTRB ADDR0 LSTRB Data direction signals -- -- RE WE R/W R/W R/W External wait feature -- -- EWAIT -- EWAIT -- Reduced input threshold enabled on -- -- Refer to Table 21-3 DATA[15:0] EWAIT DATA[15:0] EWAIT Refer to Table 21-3 1 Incl. S12X_EBI registers Refer to S12X_MMC section. 3 If EWAITE = 1, the minimum number of external bus cycles is 3. 4 Available only if configured appropriately by ROMON and EROMON (refer to S12X_MMC section). 2 MC9S12XDP512 Data Sheet, Rev. 2.21 794 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.4.2 Internal Visibility Internal visibility allows the observation of the internal MCU address and data bus as well as the determination of the access source and the CPU pipe (queue) status through the external bus interface. Internal visibility is always enabled in emulation single chip mode and emulation expanded mode. Internal CPU and BDM accesses are made visible on the external bus interface, except those to BDM firmware and BDM registers. Internal reads are made visible on ADDRx/IVDx (address and read data multiplexed, see Table 21-9 to Table 21-11), internal writes on ADDRx and DATAx (see Table 21-12 to Table 21-14). R/W and LSTRB show the type of access. External read data are also visible on IVDx. 21.4.2.1 Access Source and Instruction Queue Status Signals The access source (bus master) can be determined from the external bus control signals ACC[2:0] as shown in Table 21-8. Table 21-8. Determining Access Source from Control Signals ACC[2:0] Access Description 000 Repetition of previous access cycle 001 CPU access 010 BDM access 011 XGATE PRR access1 100 No access2 101, 110, 111 1 2 Reserved Invalid IVD brought out in read cycles Denotes also accesses to BDM firmware and BDM registers (IQSTATx are `XXXX' and R/W = 1 in these cases) The CPU instruction queue status (execution-start and data-movement information) is brought out as IQSTAT[3:0] signals. For decoding of the IQSTAT values, refer to the S12X_CPU section. 21.4.2.2 Emulation Modes Timing A bus access lasts 1 ECLK cycle. In case of a stretched external access (emulation expanded mode), up to an infinite amount of ECLK cycles may be added. ADDRx values will only be shown in ECLK high phases, while ACCx, IQSTATx, and IVDx values will only be presented in ECLK low phases. Based on this multiplex timing, ACCx are only shown in the current (first) access cycle. IQSTATx and (for read accesses) IVDx follow in the next cycle. If the access takes more than one bus cycle, ACCx display NULL (0x000) in the second and all following cycles of the access. IQSTATx display NULL (0x0000) from the third until one cycle after the access to indicate continuation. The resulting timing pattern of the external bus signals is outlined in the following tables for read, write and interleaved read/write accesses. Three examples represent different access lengths of 1, 2, and n-1 bus cycles. Non-shaded bold entries denote all values related to Access #0. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 795 Chapter 21 External Bus Interface (S12XEBIV2) The following terminology is used: `addr' -- value(ADDRx); small letters denote the logic values at the respective pins `x' -- Undefined output pin values `z' -- Tristate pins `?' -- Dependent on previous access (read or write); IVDx: `ivd' or `x'; DATAx: `data' or `z' 21.4.2.2.1 Read Access Timing Table 21-9. Read Access (1 Cycle) Access #0 Bus cycle -> ... ECLK phase ... ADDR[22:20] / ACC[2:0] ... ADDR[19:16] / IQSTAT[3:0] ... 1 Access #1 2 high low addr 0 iqstat -1 high low addr 1 iqstat 0 acc 0 ... DATA[15:0] (internal read) ... ? DATA[15:0] (external read) ... R/W ... low ... acc 2 ... addr 2 iqstat 1 ... ivd 1 ... z ... ivd 0 z z ? z 1 1 ... high acc 1 ? ADDR[15:0] / IVD[15:0] 3 z z data 0 z data 1 z ... 1 1 1 1 ... Table 21-10. Read Access (2 Cycles) Access #0 Bus cycle -> ... ECLK phase ... ADDR[22:20] / ACC[2:0] ... ADDR[19:16] / IQSTAT[3:0] ... 1 high 2 low high acc 0 addr 0 Access #1 3 low high 000 iqstat-1 addr 0 iqstat 0 ? addr 1 x ... low ... acc 1 ... 0000 ... ADDR[15:0] / IVD[15:0] ... ivd 0 ... DATA[15:0] (internal read) ... ? z z z z z ... DATA[15:0] (external read) ... ? z z z data 0 z ... R/W ... 1 1 1 1 1 1 ... Table 21-11. Read Access (n-1 Cycles) Access #0 Bus cycle -> ... ECLK phase ... ADDR[22:20] / ACC[2:0] ... ADDR[19:16] / IQSTAT[3:0] ... 1 Access #1 2 high low addr 0 iqstat-1 3 high low addr 0 iqstat 0 acc 0 high low ... 000 ... addr 0 0000 ... x ... z ... z 000 ? n ... x high addr 1 ... low ... acc 1 ... 0000 ... ivd 0 ... z ... ADDR[15:0] / IVD[15:0] ... DATA[15:0] (internal read) ... ? DATA[15:0] (external read) ... ? z z z z z ... data 0 z ... R/W ... 1 1 1 1 1 1 ... 1 1 ... z z z z MC9S12XDP512 Data Sheet, Rev. 2.21 796 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.4.2.2.2 Write Access Timing Table 21-12. Write Access (1 Cycle) Bus cycle -> ... ECLK phase ... ADDR[22:20] / ACC[2:0] ... ADDR[19:16] / IQSTAT[3:0] ... Access #0 Access #1 Access #2 1 2 3 high low addr 0 iqstat -1 high low addr 1 iqstat 0 ? ADDR[15:0] / IVD[15:0] ... DATA[15:0] (write) ... ? R/W ... 0 high low ... acc 2 ... addr 2 iqstat 1 ... x ... data 2 ... 1 ... acc 1 acc 0 x data 0 data 1 0 1 ... 1 1 Table 21-13. Write Access (2 Cycles) Access #0 Bus cycle -> ... ECLK phase ... ADDR[22:20] / ACC[2:0] ... ADDR[19:16] / IQSTAT[3:0] ... ADDR[15:0] / IVD[15:0] Access #1 1 high 2 low 3 high low acc 0 addr 0 iqstat-1 addr 0 iqstat 0 ? ... DATA[15:0] (write) ... ? R/W ... 0 high 000 addr 1 x data 0 0 0 0 1 ... low ... acc 1 ... 0000 ... x ... x ... 1 ... Table 21-14. Write Access (n-1 Cycles) Access #0 Bus cycle -> ... ECLK phase ... ADDR[22:20] / ACC[2:0] ... ADDR[19:16] / IQSTAT[3:0] ... 1 high 2 low high acc 0 addr 0 iqstat-1 ... DATA[15:0] (write) ... ? R/W ... 0 3 low high 000 addr 0 ? ADDR[15:0] / IVD[15:0] Access #1 iqstat 0 addr 0 x n ... low ... 000 ... 0000 ... x ... high addr 1 data 0 0 0 0 0 0 ... 1 ... low ... acc 1 ... 0000 ... x ... x ... 1 ... MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 797 Chapter 21 External Bus Interface (S12XEBIV2) 21.4.2.2.3 Read-Write-Read Access Timing Table 21-15. Interleaved Read-Write-Read Accesses (1 Cycle) Bus cycle -> ... ECLK phase ... ADDR[22:20] / ACC[2:0] ... ADDR[19:16] / IQSTAT[3:0] ... Access #0 Access #1 Access #2 1 2 3 high low addr 0 iqstat -1 low addr 1 iqstat 0 acc 0 ... DATA[15:0] (internal read) ... ? DATA[15:0] (external read) ... R/W ... high low ... acc 2 ... addr 2 iqstat 1 ... x ... z ... (write) data 1 z ... 0 1 ... acc 1 ? ADDR[15:0] / IVD[15:0] 21.4.2.3 high ivd 0 z z ? z data 0 1 1 0 ... (write) data 1 1 Internal Visibility Data Depending on the access size and alignment, either a word of read data is made visible on the address lines or only the related data byte will be presented in the ECLK low phase. For details refer to Table 21-16. Table 21-16. IVD Read Data Output Access Word read of data at an even and even+1 address Word read of data at an odd and odd+1 internal RAM address (misaligned) IVD[15:8] IVD[7:0] ivd(even) ivd(even+1) ivd(odd+1) ivd(odd) Byte read of data at an even address ivd(even) addr[7:0] (rep.) Byte read of data at an odd address addr[15:8] (rep.) ivd(odd) 21.4.3 Accesses to Port Replacement Registers All read and write accesses to PRR addresses take two bus clock cycles independent of the operating mode. If writing to these addresses in emulation modes, the access is directed to both, the internal register and the external resource while reads will be treated external. The XEBI control registers also belong to this category. 21.4.4 Stretched External Bus Accesses In order to allow fast internal bus cycles to coexist in a system with slower external resources, the XEBI supports stretched external bus accesses (wait states). This feature is available in normal expanded mode and emulation expanded mode for accesses to all external addresses except emulation memory and PRR. In these cases the fixed access times are 1 or 2 cycles, respectively. MC9S12XDP512 Data Sheet, Rev. 2.21 798 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) Stretched accesses are controlled by: 1. EXSTR[2:0] bits in the EBICTL1 register configuring fixed amount of stretch cycles 2. Activation of the external wait feature by EWAITE in EBICTL1 register 3. Assertion of the external EWAIT signal when EWAITE = 1 The EXSTR[2:0] control bits can be programmed for generation of a fixed number of 1 to 8 stretch cycles. If the external wait feature is enabled, the minimum number of additional stretch cycles is 2. An arbitrary amount of stretch cycles can be added using the EWAIT input. EWAIT needs to be asserted at least for a minimal specified time window within an external access cycle for the internal logic to detect it and add a cycle (refer to electrical characteristics). Holding it for additional cycles will cause the external bus access to be stretched accordingly. Write accesses are stretched by holding the initiator in its current state for additional cycles as programmed and controlled by external wait after the data have been driven out on the external bus. This results in an extension of time the bus signals and the related control signals are valid externally. Read data are not captured by the system in normal expanded mode until the specified setup time before the RE rising edge. Read data are not captured in emulation expanded mode until the specified setup time before the falling edge of ECLK. In emulation expanded mode, accesses to the internal flash or the emulation memory (determined by EROMON and ROMON bits; see S12X_MMC section for details) always take 1 cycle and stretching is not supported. In case the internal flash is taken out of the map in user applications, accesses are stretched as programmed and controlled by external wait. 21.4.5 Data Select and Data Direction Signals The S12X_EBI supports byte and word accesses at any valid external address. The big endian system of the MCU is extended to the external bus; however, word accesses are restricted to even aligned addresses. The only exception is the visibility of misaligned word accesses to addresses in the internal RAM as this module exclusively supports these kind of accesses in a single cycle. With the above restriction, a fixed relationship is implied between the address parity and the dedicated bus halves where the data are accessed: DATA[15:8] is related to even addresses and DATA[7:0] is related to odd addresses. In expanded modes the data access type is externally determined by a set of control signals, i.e., data select and data direction signals, as described below. The data select signals are not available if using the external bus interface with an 8-bit data bus. 21.4.5.1 Normal Expanded Mode In normal expanded mode, the external signals RE, WE, UDS, LDS indicate the access type (read/write), data size and alignment of an external bus access (Table 21-17). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 799 Chapter 21 External Bus Interface (S12XEBIV2) Table 21-17. Access in Normal Expanded Mode DATA[15:8] Access DATA[7:0] RE WE UDS LDS I/O data(addr) I/O data(addr) Word write of data on DATA[15:0] at an even and even+1 address 1 0 0 0 Out data(even) Out Byte write of data on DATA[7:0] at an odd address 1 0 1 0 Byte write of data on DATA[15:8] at an even address 1 0 0 1 Word read of data on DATA[15:0] at an even and even+1 address 0 1 0 0 In Byte read of data on DATA[7:0] at an odd address 0 1 1 0 In x data(odd) Out data(odd) In x data(even) In data(odd) In x In data(odd) Out data(even) Byte read of data on DATA[15:8] at an even address 0 1 0 1 In data(even) In x Indicates No Access 1 1 1 1 In x In x Unimplemented 1 1 1 0 In x In x 1 1 0 1 In x In x 21.4.5.2 Emulation Modes and Special Test Mode In emulation modes and special test mode, the external signals LSTRB, R/W, and ADDR0 indicate the access type (read/write), data size and alignment of an external bus access. Misaligned accesses to the internal RAM and misaligned XGATE PRR accesses in emulation modes are the only type of access that are able to produce LSTRB = ADDR0 = 1. This is summarized in Table 21-18. Table 21-18. Access in Emulation Modes and Special Test Mode DATA[15:8] Access DATA[7:0] R/W LSTRB ADDR0 I/O data(addr) I/O data(addr) Word write of data on DATA[15:0] at an even and even+1 address 0 0 0 Out data(even) Out data(odd) Byte write of data on DATA[7:0] at an odd address 0 0 1 In x Out data(odd) data(odd) In Byte write of data on DATA[15:8] at an even address 0 1 0 Out Word write at an odd and odd+1 internal RAM address (misaligned -- only in emulation modes) 0 1 1 Out data(odd+1) Out x Word read of data on DATA[15:0] at an even and even+1 address 1 0 0 In data(even) In data(even+1) Byte read of data on DATA[7:0] at an odd address 1 0 1 In x In data(odd) Byte read of data on DATA[15:8] at an even address 1 1 0 In data(even) In x Word read at an odd and odd+1 internal RAM address (misaligned - only in emulation modes) 1 1 1 In data(odd+1) In data(odd) data(odd) MC9S12XDP512 Data Sheet, Rev. 2.21 800 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.4.6 Low-Power Options The XEBI does not support any user-controlled options for reducing power consumption. 21.4.6.1 Run Mode The XEBI does not support any options for reducing power in run mode. Power consumption is reduced in single-chip modes due to the absence of the external bus interface. Operation in expanded modes results in a higher power consumption, however any unnecessary toggling of external bus signals is reduced to the lowest indispensable activity by holding the previous states between external accesses. 21.4.6.2 Wait Mode The XEBI does not support any options for reducing power in wait mode. 21.4.6.3 Stop Mode The XEBI will cease to function in stop mode. 21.5 Initialization/Application Information This section describes the external bus interface usage and timing. Typical customer operating modes are normal expanded mode and emulation modes, specifically to be used in emulator applications. Taking the availability of the external wait feature into account the use cases are divided into four scenarios: * Normal expanded mode -- External wait feature disabled - External wait feature enabled * Emulation modes - Emulation single-chip mode (without wait states) - Emulation expanded mode (with optional access stretching) Normal single-chip mode and special single-chip mode do not have an external bus. Special test mode is used for factory test only. Therefore, these modes are omitted here. All timing diagrams referred to throughout this section are available in the Electrical Characteristics appendix of the SoC section. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 801 Chapter 21 External Bus Interface (S12XEBIV2) 21.5.1 Normal Expanded Mode This mode allows interfacing to external memories or peripherals which are available in the commercial market. In these applications the normal bus operation requires a minimum of 1 cycle stretch for each external access. 21.5.1.1 Example 1a: External Wait Feature Disabled The first example of bus timing of an external read and write access with the external wait feature disabled is shown in * Figure `Example 1a: Normal Expanded Mode -- Read Followed by Write' The associated supply voltage dependent timing are numbers given in * * Table `Example 1a: Normal Expanded Mode Timing VDD5 = 5.0 V (EWAITE = 0)' Table `Example 1a: Normal Expanded Mode Timing VDD5 = 3.0 V (EWAITE = 0)' Systems designed this way rely on the internal programmable access stretching. These systems have predictable external memory access times. The additional stretch time can be programmed up to 8 cycles to provide longer access times. 21.5.1.2 Example 1b: External Wait Feature Enabled The external wait operation is shown in this example. It can be used to exceed the amount of stretch cycles over the programmed number in EXSTR[2:0]. The feature must be enabled by writing EWAITE = 1. If the EWAIT signal is not asserted, the number of stretch cycles is forced to a minimum of 2 cycles. If EWAIT is asserted within the predefined time window during the access it will be strobed active and another stretch cycle is added. If strobed inactive, the next cycle will be the last cycle before the access is finished. EWAIT can be held asserted as long as desired to stretch the access. An access with 1 cycle stretch by EWAIT assertion is shown in * Figure `Example 1b: Normal Expanded Mode -- Stretched Read Access' * Figure `Example 1b: Normal Expanded Mode -- Stretched Write Access' The associated timing numbers for both operations are given in * Table `Example 1b: Normal Expanded Mode Timing VDD5 = 5.0 V (EWAITE = 1)' * Table `Example 1b: Normal Expanded Mode Timing VDD5 = 3.0 V (EWAITE = 1)' It is recommended to use the free-running clock (ECLK) at the fastest rate (bus clock rate) to synchronize the EWAIT input signal. MC9S12XDP512 Data Sheet, Rev. 2.21 802 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.5.2 Emulation Modes In emulation mode applications, the development systems use a custom PRU device to rebuild the single-chip or expanded bus functions which are lost due to the use of the external bus with an emulator. Accesses to a set of registers controlling the related ports in normal modes (refer to SoC section) are directed to the external bus in emulation modes which are substituted by PRR as part of the PRU. Accesses to these registers take a constant time of 2 cycles. Depending on the setting of ROMON and EROMON (refer to S12X_MMC section), the program code can be executed from internal memory or an optional external emulation memory (EMULMEM). No wait state operation (stretching) of the external bus access is done in emulation modes when accessing internal memory or emulation memory addresses. In both modes observation of the internal operation is supported through the external bus (internal visibility). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 803 Chapter 21 External Bus Interface (S12XEBIV2) 21.5.2.1 Example 2a: Emulation Single-Chip Mode This mode is used for emulation systems in which the target application is operating in normal single-chip mode. Figure 21-5 shows the PRU connection with the available external bus signals in an emulator application. S12X_EBI Emulator ADDR[22:0]/IVD[15:0] DATA[15:0] EMULMEM PRU PRR Ports LSTRB R/W ADDR[22:20]/ACC[2:0] ADDR[19:16]/ IQSTAT[3:0] ECLK ECLKX2 Figure 21-5. Application in Emulation Single-Chip Mode The timing diagram for this operation is shown in: * Figure `Example 2a: Emulation Single-Chip Mode -- Read Followed by Write' The associated timing numbers are given in: * Table `Example 2a: Emulation Single-Chip Mode Timing (EWAITE = 0)' Timing considerations: * Signals muxed with address lines ADDRx, i.e., IVDx, IQSTATx and ACCx, have the same timing. * LSTRB has the same timing as R/W. * ECLKX2 rising edges have the same timing as ECLK edges. * The timing for accesses to PRU registers, which take 2 cycles to complete, is the same as the timing for an external non-PRR access with 1 cycle of stretch as shown in example 2b. MC9S12XDP512 Data Sheet, Rev. 2.21 804 Freescale Semiconductor Chapter 21 External Bus Interface (S12XEBIV2) 21.5.2.2 Example 2b: Emulation Expanded Mode This mode is used for emulation systems in which the target application is operating in normal expanded mode. If the external bus is used with a PRU, the external device rebuilds the data select and data direction signals UDS, LDS, RE, and WE from the ADDR0, LSTRB, and R/W signals. Figure 21-6 shows the PRU connection with the available external bus signals in an emulator application. S12X_EBI Emulator ADDR[22:0]/IVD[15:0] DATA[15:0] EMULMEM PRU PRR LSTRB R/W Ports UDS LDS RE WE ADDR[22:20]/ACC[2:0] ADDR[19:16]/ IQSTAT[3:0] EWAIT ECLK ECLKX2 CS[2:0] Figure 21-6. Application in Emulation Expanded Mode The timings of accesses with 1 stretch cycle are shown in * Figure `Example 2b: Emulation Expanded Mode -- Read with 1 Stretch Cycle' * Figure `Example 2b: Emulation Expanded Mode -- Write with 1 Stretch Cycle' The associated timing numbers are given in * Table `Example 2b: Emulation Expanded Mode Timing VDD5 = 5.0 V (EWAITE = 0)' (this also includes examples for alternative settings of 2 and 3 additional stretch cycles) Timing considerations: * If no stretch cycle is added, the timing is the same as in Emulation Single-Chip Mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 805 Chapter 21 External Bus Interface (S12XEBIV2) MC9S12XDP512 Data Sheet, Rev. 2.21 806 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.1 Introduction The S12XD family port integration module (below referred to as PIM) establishes the interface between the peripheral modules including the non-multiplexed external bus interface module (S12X_EBI) and the I/O pins for all ports. It controls the electrical pin properties as well as the signal prioritization and multiplexing on shared pins. This document covers the description of: * Port A, B used as address output of the S12X_EBI * Port C, D used as data I/O of the S12X_EBI * Port E associated with the S12X_EBI control signals and the IRQ, XIRQ interrupt inputs * Port K associated with address output and control signals of the S12X_EBI * Port T connected to the Enhanced Capture Timer (ECT) module * Port S associated with 2 SCI and 1 SPI modules * Port M associated with 4 MSCAN modules and 1 SCI module * Port P connected to the PWM and 2 SPI modules -- inputs can be used as an external interrupt source * Port H associated with 2 SCI modules -- inputs can be used as an external interrupt source * Port J associated with 1 MSCAN, 1 SCI, and 2 IIC modules -- inputs can be used as an external interrupt source * Port AD0 and AD1 associated with one 8-channel and one 16-channel ATD module Most I/O pins can be configured by register bits to select data direction and drive strength, to enable and select pull-up or pull-down devices. Interrupts can be enabled on specific pins resulting in status flags. The I/O's of 2 MSCAN and all 3 SPI modules can be routed from their default location to alternative port pins. NOTE The implementation of the PIM is device dependent. Therefore some functions are not available on certain derivatives or 112-pin and 80-pin package options. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 807 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.1.1 Features A full-featured PIM module includes these distinctive registers: * Data and data direction registers for Ports A, B, C, D, E, K, T, S, M, P, H, J, AD0, and AD1 when used as general-purpose I/O * Control registers to enable/disable pull-device and select pull-ups/pull-downs on Ports T, S, M, P, H, and J on per-pin basis * Control registers to enable/disable pull-up devices on Ports AD0, and AD1 on per-pin basis * Single control register to enable/disable pull-ups on Ports A, B, C, D, E, and K on per-port basis and on BKGD pin * Control registers to enable/disable reduced output drive on Ports T, S, M, P, H, J, AD0, and AD1 on per-pin basis * Single control register to enable/disable reduced output drive on Ports A, B, C, D, E, and K on per-port basis * Control registers to enable/disable open-drain (wired-OR) mode on Ports S and M * Control registers to enable/disable pin interrupts on Ports P, H, and J * Interrupt flag register for pin interrupts on Ports P, H, and J * Control register to configure IRQ pin operation * Free-running clock outputs A standard port pin has the following minimum features: * Input/output selection * 5V output drive with two selectable drive strengths * 5V digital and analog input * Input with selectable pull-up or pull-down device Optional features: * Open drain for wired-OR connections * Interrupt inputs with glitch filtering * Reduced input threshold to support low voltage applications 22.1.2 Block Diagram Figure 22-1 is a block diagram of the PIM. * Signals shown in Bold are not available in 80-pin packages. * Signals shown in Bold-Italics are neither available in 112-pin nor in 80-pin packages. * Shaded labels denote alternative module routing ports. MC9S12XDP512 Data Sheet, Rev. 2.21 808 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 Port D DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 Port AD1 Port AD0 Port T Port P SCK SS MOSI MISO SS SPI1 SCK MOSI MISO SPI2 PP7 PP6 PP5 PP4 PP3 PP2 PP1 PP0 PS7 PS6 PS5 PS4 PS3 PS2 PS1 PS0 SS SPI0 SCK MOSI MISO TXD SCI1 RXD TXD SCI0 RXD BKGD/MODC ECLKX2/XCLKS TAGHI/MODB TAGLO/RE/MODA ECLK S12X_EBI LDS/LSTRB S12X_BDM WE/R/W S12X_DBG IRQ XIRQ S12X_INT EWAIT/ROMCTL NOACC/ADDR22 ADDR21 ADRR20 ADDR19 ADDR18 ADDR17 ADDR16 Port E ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0/UDS PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 PT7 PT6 PT5 PT4 PT3 PT2 PT1 PT0 Port K ADDR15 ADDR14 ADDR13 ADDR12 ADDR11 ADDR10 ADDR9 ADDR8 TXD SCI3 RXD PAD22 PAD20 PAD18 PAD16 PAD14 PAD12 PAD10 PAD08 PAD07 PAD06 PAD05 PAD04 PAD03 PAD02 PAD01 PAD00 Port S IOC7 IOC6 IOC5 IOC4 IOC3 IOC2 IOC1 IOC0 ATD1 TXCAN CAN3 RXCAN TXCAN CAN2 RXCAN TXCAN CAN1 RXCAN TXCAN CAN0 RXCAN Interrupt Logic SPI0 CAN0 CAN0 CAN4 CAN4 AN7 AN6 AN5 AN4 AN3 AN2 AN1 AN0 SCI2 PWM Interrupt Logic TXCAN CAN4 RXCAN SCL IIC0 SDA SCL IIC1 SDA TXD RXD AN15,14 AN13,12 AN11,10 AN9,8 AN7,6 AN5,4 AN3,2 AN1,0 ATD0 TXD SCI5 RXD TXD SCI4 RXD Port C PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 Port B PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 Port A PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 Port M PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 Port J PM7 PM6 PM5 PM4 PM3 PM2 PM1 PM0 Interrupt Logic CAN0 PJ6 PJ5 PJ4 PJ2 PJ1 PJ0 SPI1 PJ7 SPI2 Port H PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 ECT Port Integration Module PAD23 PAD21 PAD19 PAD17 PAD15 PAD13 PAD11 PAD09 BKGD PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 PK7 PK6 PK5 PK4 PK3 PK2 PK1 PK0 Figure 22-1. PIM Block Diagram MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 809 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.2 External Signal Description This section lists and describes the signals that do connect off-chip. 22.2.1 Signal Properties Table 22-1 shows all the pins and their functions that are controlled by the PIM. Refer to Section 22.4, "Functional Description" for the availability of the individual pins in the different package options. NOTE If there is more than one function associated with a pin, the priority is indicated by the position in the table from top (highest priority) to bottom (lowest priority). Table 22-1. Pin Functions and Priorities (Sheet 1 of 7) Port Pin Name Pin Function and Priority I/O -- BKGD MODC1 I BKGD I/O S12X_BDM communication pin ADDR[15:8] mux IVD[15:8]2 O High-order external bus address output (multiplexed with IVIS data) GPIO I/O General-purpose I/O ADDR[7:1] mux IVD[7:1]2 O Low-order external bus address output (multiplexed with IVIS data) GPIO I/O General-purpose I/O ADDR[0] mux IVD02 O Low-order external bus address output (multiplexed with IVIS data) UDS O Upper data strobe GPIO I/O General-purpose I/O DATA[15:8] I/O High-order bidirectional data input/output Configurable for reduced input threshold GPIO I/O General-purpose I/O DATA[7:0] I/O Low-order bidirectional data input/output Configurable for reduced input threshold GPIO I/O General-purpose I/O A B PA[7:0] PB[7:1] PB[0] C D PC[7:0] PD[7:0] Description MODC input during RESET Pin Function after Reset BKGD Mode dependent3 Mode dependent3 Mode dependent3 Mode dependent3 MC9S12XDP512 Data Sheet, Rev. 2.21 810 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-1. Pin Functions and Priorities (Sheet 2 of 7) Port Pin Name PE[7] PE[6] Pin Function and Priority I/O XCLKS1 I External clock selection input during RESET ECLKX2 I Free-running clock output at Core Clock rate (ECLK x 2) GPIO I/O MODB1 I MODB input during RESET TAGHI I Instruction tagging low pin Configurable for reduced input threshold GPIO I/O MODA1 I MODA input during RESET RE O Read enable signal TAGLO I Instruction tagging low pin Configurable for reduced input threshold GPIO I/O General-purpose I/O ECLK O Free-running clock output at the Bus Clock rate or programmable divided in normal modes GPIO I/O General-purpose I/O EROMCTL1 I EROMON bit control input during RESET LSTRB O Low strobe bar output LDS O Lower data strobe GPIO I/O General-purpose I/O R/W O Read/write output for external bus WE O Write enable signal GPIO I/O General-purpose I/O IRQ I GPIO I/O XIRQ I GPIO I/O PE[5] E PE[4] PE[3] PE[2] Description Pin Function after Reset General-purpose I/O General-purpose I/O Mode dependent3 Maskable level- or falling edge-sensitive interrupt input PE[1] General-purpose I/O Non-maskable level-sensitive interrupt input PE[0] General-purpose I/O MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 811 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-1. Pin Functions and Priorities (Sheet 3 of 7) Port Pin Name PK[7] K PK[6:4] PK[3:0] T Pin Function and Priority I/O Pin Function after Reset ROMCTL1 I ROMON bit control input during RESET EWAIT I External Wait signal Configurable for reduced input threshold GPIO I/O General-purpose I/O ADDR[22:20] mux ACC[2:0]2 O Extended external bus address output (multiplexed with access master output) GPIO I/O General-purpose I/O ADDR[19:16] mux IQSTAT[3:0]2 O Extended external bus address output (multiplexed with instruction pipe status bits) GPIO I/O General-purpose I/O IOC[7:0] I/O Enhanced Capture Timer Channels 7-0 input/output GPIO I/O General-purpose I/O SS0 I/O Serial Peripheral Interface 0 slave select output in master mode, input in slave mode or master mode. GPIO I/O General-purpose I/O SCK0 I/O Serial Peripheral Interface 0 serial clock pin GPIO I/O General-purpose I/O MOSI0 I/O Serial Peripheral Interface 0 master out/slave in pin GPIO I/O General-purpose I/O MISO0 I/O Serial Peripheral Interface 0 master in/slave out pin GPIO I/O General-purpose I/O TXD1 O Serial Communication Interface 1 transmit pin GPIO I/O General-purpose I/O RXD1 I GPIO I/O General-purpose I/O TXD0 O Serial Communication Interface 0 transmit pin GPIO I/O General-purpose I/O RXD0 I GPIO I/O Description Mode dependent3 PT[7:0] GPIO PS7 PS6 PS5 PS4 S GPIO PS3 Serial Communication Interface 1 receive pin PS2 PS1 Serial Communication Interface 0 receive pin PS0 General-purpose I/O MC9S12XDP512 Data Sheet, Rev. 2.21 812 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-1. Pin Functions and Priorities (Sheet 4 of 7) Port Pin Name Pin Function and Priority I/O TXCAN3 O MSCAN3 transmit pin TXCAN4 O MSCAN4 transmit pin TXD3 O Serial Communication Interface 3 transmit pin GPIO I/O General-purpose I/O RXCAN3 I MSCAN3 receive pin RXCAN4 I MSCAN4 receive pin RXD3 I Serial Communication Interface 3 receive pin GPIO I/O General-purpose I/O TXCAN2 O MSCAN2 transmit pin TXCAN0 O MSCAN0 transmit pin TXCAN4 O MSCAN4 transmit pin SCK0 I/O Serial Peripheral Interface 0 serial clock pin If CAN0 is routed to PM[3:2] the SPI0 can still be used in bidirectional master mode. GPIO I/O General-purpose I/O RXCAN2 I MSCAN2 receive pin RXCAN0 I MSCAN0 receive pin RXCAN4 I MSCAN4 receive pin MOSI0 I/O Serial Peripheral Interface 0 master out/slave in pin If CAN0 is routed to PM[3:2] the SPI0 can still be used in bidirectional master mode. GPIO I/O General-purpose I/O TXCAN1 O MSCAN1 transmit pin TXCAN0 O MSCAN0 transmit pin SS0 I/O Serial Peripheral Interface 0 slave select output in master mode, input for slave mode or master mode. GPIO I/O General-purpose I/O RXCAN1 I MSCAN1 receive pin RXCAN0 I MSCAN0 receive pin MISO0 I/O Serial Peripheral Interface 0 master in/slave out pin GPIO I/O General-purpose I/O TXCAN0 O MSCAN0 transmit pin GPIO I/O General-purpose I/O RXCAN0 I MSCAN0 receive pin GPIO I/O General-purpose I/O Description Pin Function after Reset PM7 PM6 PM5 M PM4 PM3 GPIO PM2 PM1 PM0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 813 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-1. Pin Functions and Priorities (Sheet 5 of 7) Port Pin Name PP7 PP6 PP5 PP4 Pin Function and Priority I/O Pin Function after Reset PWM7 I/O Pulse Width Modulator input/output channel 7 SCK2 I/O Serial Peripheral Interface 2 serial clock pin GPIO/KWP7 I/O General-purpose I/O with interrupt PWM6 O Pulse Width Modulator output channel 6 SS2 I/O Serial Peripheral Interface 2 slave select output in master mode, input for slave mode or master mode. GPIO/KWP6 I/O General-purpose I/O with interrupt PWM5 O Pulse Width Modulator output channel 5 MOSI2 I/O Serial Peripheral Interface 2 master out/slave in pin GPIO/KWP5 I/O General-purpose I/O with interrupt PWM4 O Pulse Width Modulator output channel 4 MISO2 I/O Serial Peripheral Interface 2 master in/slave out pin GPIO/KWP4 I/O General-purpose I/O with interrupt PWM3 O Pulse Width Modulator output channel 3 SS1 I/O Serial Peripheral Interface 1 slave select output in master mode, input for slave mode or master mode. GPIO/KWP3 I/O General-purpose I/O with interrupt PWM2 O Pulse Width Modulator output channel 2 SCK1 I/O Serial Peripheral Interface 1 serial clock pin GPIO/KWP2 I/O General-purpose I/O with interrupt PWM1 O Pulse Width Modulator output channel 1 MOSI1 I/O Serial Peripheral Interface 1 master out/slave in pin GPIO/KWP1 I/O General-purpose I/O with interrupt PWM0 O Pulse Width Modulator output channel 0 MISO1 I/O Serial Peripheral Interface 1 master in/slave out pin GPIO/KWP0 I/O General-purpose I/O with interrupt Description P GPIO PP3 PP2 PP1 PP0 MC9S12XDP512 Data Sheet, Rev. 2.21 814 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-1. Pin Functions and Priorities (Sheet 6 of 7) Port Pin Name PH7 PH6 PH5 Pin Function and Priority I/O SS2 I/O Serial Peripheral Interface 2 slave select output in master mode, input for slave mode or master mode TXD5 O Serial Communication Interface 5 transmit pin GPIO/KWH7 I/O General-purpose I/O with interrupt SCK2 I/O Serial Peripheral Interface 2 serial clock pin RXD5 I GPIO/KWH6 I/O General-purpose I/O with interrupt MOSI2 I/O Serial Peripheral Interface 2 master out/slave in pin TXD4 O Serial Communication Interface 4 transmit pin GPIO/KWH5 I/O General-purpose I/O with interrupt MISO2 I/O Serial Peripheral Interface 2 master in/slave out pin RXD4 I GPIO/KWH4 I/O General-purpose I/O with interrupt SS1 I/O Serial Peripheral Interface 1 slave select output in master mode, input for slave mode or master mode. GPIO/KWH3 I/O General-purpose I/O with interrupt SCK1 I/O Serial Peripheral Interface 1 serial clock pin GPIO/KWH2 I/O General-purpose I/O with interrupt MOSI1 I/O Serial Peripheral Interface 1 master out/slave in pin GPIO/KWH1 I/O General-purpose I/O with interrupt MISO1 I/O Serial Peripheral Interface 1 master in/slave out pin GPIO/KWH0 I/O General-purpose I/O with interrupt Description Pin Function after Reset Serial Communication Interface 5 receive pin H GPIO PH4 PH3 Serial Communication Interface 4 receive pin PH2 PH1 PH0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 815 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-1. Pin Functions and Priorities (Sheet 7 of 7) Port Pin Name Pin Function and Priority I/O TXCAN4 O MSCAN4 transmit pin SCL0 O Inter Integrated Circuit 0 serial clock line TXCAN0 O MSCAN0 transmit pin GPIO/KWJ7 I/O General-purpose I/O with interrupt RXCAN4 I SDA0 I/O RXCAN0 I GPIO/KWJ6 I/O General-purpose I/O with interrupt SCL1 O Inter Integrated Circuit 1 serial clock line CS2 O Chip select 2 GPIO/KWJ7 I/O General-purpose I/O with interrupt SDA1 I/O Inter Integrated Circuit 1 serial data line CS0 O Chip select 0 GPIO/KWJ6 I/O General-purpose I/O with interrupt CS1 O Chip select 1 GPIO/KWJ2 I/O General-purpose I/O with interrupt TXD2 O Serial Communication Interface 2 transmit pin GPIO/KWJ1 I/O General-purpose I/O with interrupt RXD2 I Serial Communication Interface 2 receive pin CS3 O Chip select 3 GPIO/KWJ0 I/O General-purpose I/O with interrupt GPIO I/O General-purpose I/O AN[7:0] I ATD0 analog inputs GPIO I/O General-purpose I/O AN[15:0] I ATD1 analog inputs Description Pin Function after Reset PJ7 MSCAN4 receive pin Inter Integrated Circuit 0 serial data line PJ6 PJ5 J PJ4 MSCAN0 receive pin GPIO PJ2 PJ1 PJ0 AD0 AD1 PAD[07:00] GPIO PAD[23:08] GPIO 1 Function active when RESET asserted. Only available in emulation modes or in Special Test Mode with IVIS on. 3 Refer also to Table 22-70 and S12X_EBI section. 2 MC9S12XDP512 Data Sheet, Rev. 2.21 816 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3 Memory Map and Register Definition This section provides a detailed description of all PIM registers. 22.3.1 Module Memory Map Table 22-2 shows the register map of the port integration module. Table 22-2. PIM Memory Map (Sheet 1 of 3) Address Use Access 0x0000 Port A Data Register (PORTA) Read / Write 0x0001 Port B Data Register (PORTB) Read / Write 0x0002 Port A Data Direction Register (DDRA) Read / Write 0x0003 Port B Data Direction Register (DDRB) Read / Write 0x0004 Port C Data Register (PORTC) Read / Write 0x0005 Port D Data Register (PORTD) Read / Write 0x0006 Port C Data Direction Register (DDRC) Read / Write 0x0007 Port D Data Direction Register (DDRD) Read / Write 0x0008 Port E Data Register (PORTE) Read / Write1 0x0009 Port E Data Direction Register (DDRE) Read / Write1 0x000A : 0x000B Non-PIM Address Range 0x000C Pull-up Up Control Register (PUCR) Read / Write1 0x000D Reduced Drive Register (RDRIV) Read / Write1 0x000E : 0x001B Non-PIM Address Range 0x001C ECLK Control Register (ECLKCTL) 0x001D PIM Reserved 0x001E IRQ Control Register (IRQCR) 0x001F PIM Reserved -- 0x0020 : 0x0031 Non-PIM Address Range -- 0x0032 Port K Data Register (PORTK) Read / Write 0x0033 Port K Data Direction Register (DDRK) Read / Write 0x0034 : 0x023F Non-PIM Address Range 0x0240 Port T Data Register (PTT) -- -- Read / Write1 -- Read / Write1 -- Read / Write MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 817 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-2. PIM Memory Map (Sheet 2 of 3) Address Use Access 0x0241 Port T Input Register (PTIT) Read 0x0242 Port T Data Direction Register (DDRT) Read / Write 0x0243 Port T Reduced Drive Register (RDRT) Read / Write 0x0244 Port T Pull Device Enable Register (PERT) Read / Write 0x0245 Port T Polarity Select Register (PPST) Read / Write 0x0246 Reserved -- 0x0247 Reserved -- 0x0248 Port S Data Register (PTS) Read / Write 0x0249 Port S Input Register (PTIS) Read 0x024A Port S Data Direction Register (DDRS) Read / Write 0x024B Port S Reduced Drive Register (RDRS) Read / Write 0x024C Port S Pull Device Enable Register (PERS) Read / Write 0x024D Port S Polarity Select Register (PPSS) Read / Write 0x024E Port S Wired-OR Mode Register (WOMS) Read / Write 0x024F Reserved 0x0250 Port M Data Register (PTM) Read / Write 0x0251 Port M Input Register (PTIM) Read 0x0252 Port M Data Direction Register (DDRM) Read / Write 0x0253 Port M Reduced Drive Register (RDRM) Read / Write 0x0254 Port M Pull Device Enable Register (PERM) Read / Write 0x0255 Port M Polarity Select Register (PPSM) Read / Write 0x0256 Port M Wired-OR Mode Register (WOMM) Read / Write 0x0257 Module Routing Register (MODRR) Read / Write 0x0258 Port P Data Register (PTP) Read / Write 0x0259 Port P Input Register (PTIP) Read 0x025A Port P Data Direction Register (DDRP) Read / Write 0x025B Port P Reduced Drive Register (RDRP) Read / Write 0x025C Port P Pull Device Enable Register (PERP) Read / Write 0x025D Port P Polarity Select Register (PPSP) Read / Write 0x025E Port P Interrupt Enable Register (PIEP) Read / Write 0x025F Port P Interrupt Flag Register (PIFP) Read / Write 0x0260 Port H Data Register (PTH) Read / Write 0x0261 Port H Input Register (PTIH) Read 0x0262 Port H Data Direction Register (DDRH) Read / Write 0x0263 Port H Reduced Drive Register (RDRH) Read / Write -- MC9S12XDP512 Data Sheet, Rev. 2.21 818 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-2. PIM Memory Map (Sheet 3 of 3) Address 1 Use Access 0x0264 Port H Pull Device Enable Register (PERH) Read / Write 0x0265 Port H Polarity Select Register (PPSH) Read / Write 0x0266 Port H Interrupt Enable Register (PIEH) Read / Write 0x0267 Port H Interrupt Flag Register (PIFH) Read / Write 0x0268 Port J Data Register (PTJ) Read / Write1 0x0269 Port J Input Register (PTIJ) Read 0x026A Port J Data Direction Register (DDRJ) Read / Write1 0x026B Port J Reduced Drive Register (RDRJ) Read / Write1 0x026C Port J Pull Device Enable Register (PERJ) Read / Write1 0x026D Port J Polarity Select Register (PPSJ) Read / Write1 0x026E Port J Interrupt Enable Register (PIEJ) Read / Write1 0x026F Port J Interrupt Flag Register (PIFJ) Read / Write1 0x0270 Reserved 0x0271 Port AD0 Data Register 1 (PT1AD0) 0x0272 Reserved 0x0273 Port AD0 Data Direction Register 1 (DDR1AD0) 0x0274 Reserved 0x0275 Port AD0 Reduced Drive Register 1 (RDR1AD0) 0x0276 Reserved 0x0277 Port AD0 Pull Up Enable Register 1 (PER1AD0) Read / Write 0x0278 Port AD1 Data Register 0 (PT0AD1) Read / Write 0x0279 Port AD1 Data Register 1 (PT1AD1) Read / Write 0x027A Port AD1 Data Direction Register 0 (DDR0AD1) Read / Write 0x027B Port AD1 Data Direction Register 1 (DDR1AD1) Read / Write 0x027C Port AD1 Reduced Drive Register 0 (RDR0AD1) Read / Write 0x027D Port AD1 Reduced Drive Register 1 (RDR1AD1) Read / Write 0x027E Port AD1 Pull Up Enable Register 0 (PER0AD1) Read / Write 0x027F Port AD1 Pull Up Enable Register 1 (PER1AD1) Read / Write -- Read / Write -- Read / Write -- Read / Write -- Write access not applicable for one or more register bits. Refer to Section 22.3.2, "Register Descriptions". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 819 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2 Register Descriptions Table 22-3 summarizes the effect on the various configuration bits, data direction (DDR), output level (IO), reduced drive (RDR), pull enable (PE), pull select (PS), and interrupt enable (IE) for the ports. The configuration bit PS is used for two purposes: 1. Configure the sensitive interrupt edge (rising or falling), if interrupt is enabled. 2. Select either a pull-up or pull-down device if PE is active. Table 22-3. Pin Configuration Summary 1 2 DDR IO RDR PE PS1 IE2 0 x x 0 x 0 Input Disabled Disabled 0 x x 1 0 0 Input Pull Up Disabled 0 x x 1 1 0 Input Pull Down Disabled 0 x x 0 0 1 Input Disabled Falling edge 0 x x 0 1 1 Input Disabled Rising edge 0 x x 1 0 1 Input Pull Up Falling edge 0 x x 1 1 1 Input Pull Down Rising edge 1 0 0 x x 0 Output, full drive to 0 Disabled Disabled 1 1 0 x x 0 Output, full drive to 1 Disabled Disabled 1 0 1 x x 0 Output, reduced drive to 0 Disabled Disabled 1 1 1 x x 0 Output, reduced drive to 1 Disabled Disabled 1 0 0 x 0 1 Output, full drive to 0 Disabled Falling edge 1 1 0 x 1 1 Output, full drive to 1 Disabled Rising edge 1 0 1 x 0 1 Output, reduced drive to 0 Disabled Falling edge 1 1 1 x 1 1 Output, reduced drive to 1 Disabled Rising edge Function Pull Device Interrupt Always "0" on Port A, B, C, D, E, K, AD0, and AD1. Applicable only on Port P, H, and J. NOTE All register bits in this module are completely synchronous to internal clocks during a register read. MC9S12XDP512 Data Sheet, Rev. 2.21 820 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Register Name PORTA R W PORTB R W DDRA R W DDRB R W PORTC R W PORTD R W DDRC R W DDRD R W PORTE R W DDRE R W Bit 7 6 5 4 3 2 1 Bit 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 DDRC7 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 0 0 R Non-PIM W Address Range PUCR R W RDRIV R W Non-PIM Address Range PUPKE RDPK R Non-PIM W Address Range BKPUE 0 0 PUPEE PUPDE PUPCE PUPBE PUPAE RDPE RDPD RDPC RDPB RDPA 0 Non-PIM Address Range = Unimplemented or Reserved Figure 22-2. PIM Register Summary (Sheet 1 of 6) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 821 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Register Name ECLKCTL R W Reserved R Bit 7 6 NECLK NCLKX2 0 0 IRQE IRQEN 0 0 5 4 3 2 1 Bit 0 0 0 0 0 EDIV1 EDIV0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W IRQCR R W Reserved R W Non-PIM R Address W Range PORTK R W DDRK R W Non-PIM Address Range PK7 PK6 PK5 PK4 PK3 PK2 PK1 PK0 DDRK7 DDRK6 DDRK5 DDRK4 DDRK3 DDRK2 DDRK1 DDRK0 Non-PIM R Address W Range PTT R W PTIT R Non-PIM Address Range PTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0 PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0 DDRT7 DDRT6 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0 RDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0 PERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 W DDRT R W RDRT R W PERT R W PPST R W = Unimplemented or Reserved Figure 22-2. PIM Register Summary (Sheet 2 of 6) MC9S12XDP512 Data Sheet, Rev. 2.21 822 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Register Name Reserved R Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0 PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0 DDRS7 DDRS6 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0 RDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0 PERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0 PPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0 WOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0 0 0 0 0 0 0 0 0 PTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0 PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0 DDRM7 DDRM6 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0 RDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0 PERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0 W Reserved R W PTS R W PTIS R W DDRS R W RDRS R W PERS R W PPSS R W WOMS R W Reserved R W PTM R W PTIM R W DDRM R W RDRM R W PERM R W = Unimplemented or Reserved Figure 22-2. PIM Register Summary (Sheet 3 of 6) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 823 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Register Name PPSM R W WOMM R W MODRR R Bit 7 6 5 4 3 2 1 Bit 0 PPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0 WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 MODRR6 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0 PTP7 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0 PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0 DDRP7 DDRP6 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0 RDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0 PERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0 PPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSP0 PIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0 PIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0 PTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0 PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0 DDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 RDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0 0 W PTP R W PTIP R W DDRP R W RDRP R W PERP R W PPSP R W PIEP R W PIFP R W PTH R W PTIH R W DDRH R W RDRH R W = Unimplemented or Reserved Figure 22-2. PIM Register Summary (Sheet 4 of 6) MC9S12XDP512 Data Sheet, Rev. 2.21 824 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Register Name PERH R W PPSH R W PIEH R W PIFH R W PTJ R W PTIJ R Bit 7 6 5 4 3 2 1 Bit 0 PERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0 PPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0 PIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0 PIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0 PTJ7 PTJ6 PTJ5 PTJ4 PTJ2 PTJ1 PTJ0 PTIJ7 PTIJ6 PTIJ5 PTIJ4 PTIJ2 PTIJ1 PTIJ0 DDRJ7 DDRJ6 DDRJ5 DDRJ4 DDRJ2 DDRJ1 DDRJ0 RDRJ7 RDRJ6 RDRJ5 RDRJ4 RDRJ2 RDRJ1 RDRJ0 PERJ7 PERJ6 PERJ5 PERJ4 PERJ2 PERJ1 PERJ0 PPSJ7 PPSJ6 PPSJ5 PPSJ4 PPSJ2 PPSJ1 PPSJ0 PIEJ7 PIEJ6 PIEJ5 PIEJ4 PIEJ2 PIEJ1 PIEJ0 PPSJ7 PPSJ6 PPSJ5 PPSJ4 PPSJ2 PPSJ1 PPSJ0 0 0 0 0 0 0 0 0 PT1AD07 PT1AD06 PT1AD05 PT1AD04 PT1AD03 PT1AD02 PT1AD01 PT1AD00 0 0 0 0 0 0 0 0 0 0 W DDRJ R W RDRJ R W PERJ R W PPSJ R W PIEJ R W PIFJ R W Reserved R 0 0 0 0 0 0 W PT1AD0 R W Reserved R W = Unimplemented or Reserved Figure 22-2. PIM Register Summary (Sheet 5 of 6) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 825 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Register Name Name Bit 7 R W Reserved R 6 5 4 3 2 1 Bit 0 DDR1AD07 DDR1AD06 DDR1AD05 DDR1AD04 DDR1AD03 DDR1AD02 DDR1AD01 DDR1AD00 0 0 0 0 0 0 0 0 W RDR1AD0 R W Reserved R RDR1AD07 RDR1AD06 RDR1AD05 RDR1AD04 RDR1AD03 RDR1AD02 RDR1AD01 RDR1AD00 0 0 0 0 0 0 0 0 PER1AD07 PER1AD06 PER1AD05 PER1AD04 PER1AD03 PER1AD02 PER1AD01 PER1AD00 PT0AD123 PT0AD122 PT0AD121 PT0AD120 PT0AD119 PT0AD118 PT0AD117 PT0AD116 PT1AD115 PT1AD114 PT1AD113 PT1AD112 PT1AD111 PT1AD110 PT1AD19 PT1AD18 W PER1AD0 R W PT0AD1 R W PT1AD1 R W DDR0AD1 R W DDR1AD1 R W RDR0AD1 R W RDR1AD1 R W PER0AD1 R W PER1AD1 R W DDR0AD123 DDR0AD122 DDR0AD121 DDR0AD120 DDR0AD119 DDR0AD118 DDR0AD117 DDR0AD116 DDR1AD115 DDR1AD114 DDR1AD113 DDR1AD112 DDR1AD111 DDR1AD110 DDR1AD19 DDR1AD18 RDR0AD123 RDR0AD122 RDR0AD121 RDR0AD120 RDR0AD119 RDR0AD118 RDR0AD117 RDR0AD116 RDR1AD115 RDR1AD114 RDR1AD113 RDR1AD112 RDR1AD111 RDR1AD110 RDR1AD19 RDR1AD18 PER0AD123 PER0AD122 PER0AD121 PER0AD120 PER0AD119 PER0AD118 PER0AD117 PER0AD116 PER1AD115 PER1AD114 PER1AD113 PER1AD112 PER1AD111 PER1AD110 PER1AD19 PER1AD18 = Unimplemented or Reserved Figure 22-2. PIM Register Summary (Sheet 6 of 6) MC9S12XDP512 Data Sheet, Rev. 2.21 826 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.1 Port A Data Register (PORTA) 7 6 5 4 3 2 1 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 ADDR15 mux IVD15 ADDR14 mux IVD14 ADDR13 mux IVD13 ADDR12 mux IVD12 ADDR11 mux IVD11 ADDR10 mux IVD10 ADDR9 mux IVD9 ADDR8 mux IVD8 0 0 0 0 0 0 0 0 R W Alt. Function Reset Figure 22-3. Port A Data Register (PORTA) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-4. PORTA Field Descriptions Field Description 7-0 PA[7:0] Port A -- Port A pins 7-0 are associated with address outputs ADDR15 through ADDR8 respectively in expanded modes. When this port is not used for external addresses, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 22.3.2.2 Port B Data Register (PORTB) 7 6 5 4 3 2 1 0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 ADDR7 mux IVD7 ADDR6 mux IVD6 ADDR5 mux IVD5 ADDR4 mux IVD4 ADDR3 mux IVD3 ADDR2 mux IVD2 ADDR1 mux IVD1 ADDR0 mux IVD0 or UDS 0 0 0 0 0 0 0 0 R W Alt. Function Reset Figure 22-4. Port B Data Register (PORTB) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 827 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-5. PORTB Field Descriptions Field Description 7-0 PB[7:0] Port B -- Port B pins 7-0 are associated with address outputs ADDR7 through ADDR1 respectively in expanded modes. Pin 0 is associated with output ADDR0 in emulation modes and special test mode and with Upper Data Select (UDS) in normal expanded mode. When this port is not used for external addresses, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. MC9S12XDP512 Data Sheet, Rev. 2.21 828 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.3 Port A Data Direction Register (DDRA) 7 6 5 4 3 2 1 0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0 0 0 0 0 0 0 0 R W Reset Figure 22-5. Port A Data Direction Register (DDRA) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-6. DDRA Field Descriptions Field Description 7-0 DDRA[7:0] Data Direction Port A -- This register controls the data direction for port A. When Port A is operating as a general purpose I/O port, DDRA determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTA after changing the DDRA register. 22.3.2.4 Port B Data Direction Register (DDRB) 7 6 5 4 3 2 1 0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 0 0 0 0 0 0 0 0 R W Reset Figure 22-6. Port B Data Direction Register (DDRB) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-7. DDRB Field Descriptions Field Description 7-0 DDRB[7:0] Data Direction Port B -- This register controls the data direction for port B. When Port B is operating as a general purpose I/O port, DDRB determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTB after changing the DDRB register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 829 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.5 Port C Data Register (PORTC) 7 6 5 4 3 2 1 0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 Exp.: DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 Reset 0 0 0 0 0 0 0 0 R W Figure 22-7. Port C Data Register (PORTC) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-8. PORTC Field Descriptions Field Description 7-0 PC[7:0] Port C -- Port C pins 7-0 are associated with data I/O lines DATA15 through DATA8 respectively in expanded modes. When this port is not used for external data, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 22.3.2.6 Port D Data Register (PORTD) 7 6 5 4 3 2 1 0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 Exp.: DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 Reset 0 0 0 0 0 0 0 0 R W Figure 22-8. Port D Data Register (PORTD) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-9. PORTD Field Descriptions Field Description 7-0 PD[7:0] Port D -- Port D pins 7-0 are associated with data I/O lines DATA7 through DATA0 respectively in expanded modes. When this port is not used for external data, these pins can be used as general purpose I/O. -- If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. MC9S12XDP512 Data Sheet, Rev. 2.21 830 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.7 Port C Data Direction Register (DDRC) 7 6 5 4 3 2 1 0 DDRC7 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 0 0 0 0 0 0 0 0 R W Reset Figure 22-9. Port C Data Direction Register (DDRC) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-10. DDRC Field Descriptions Field Description 7-0 DDRC[7:0] Data Direction Port C -- This register controls the data direction for port C. When Port C is operating as a general purpose I/O port, DDRC determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTC after changing the DDRC register. 22.3.2.8 Port D Data Direction Register (DDRD) 7 6 5 4 3 2 1 0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 0 0 0 0 0 0 0 0 R W Reset Figure 22-10. Port D Data Direction Register (DDRD) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-11. DDRD Field Descriptions Field Description 7-0 DDRD[7:0] Data Direction Port D -- This register controls the data direction for port D. When Port D is operating as a general purpose I/O port, DDRD determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTD after changing the DDRD register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 831 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.9 Port E Data Register (PORTE) 7 6 5 4 3 2 1 0 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 Alt. Func. XCLKS or ECLKX2 MODB or TAGHI MODA or RE or TAGLO ECLK EROMCTL or LSTRB or LDS R/W or WE IRQ XIRQ Reset 0 0 0 0 0 0 --1 --1 R W = Unimplemented or Reserved Figure 22-11. Port E Data Register (PORTE) 1 These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-12. PORTE Field Descriptions Field Description 7-0 PE[7:0] Port E -- Port E bits 7-0 are associated with external bus control signals and interrupt inputs. These include mode select (MODB, MODA), E clock, double frequency E clock, Instruction Tagging High and Low (TAGHI, TAGLO), Read/Write (R/W), Read Enable and Write Enable (RE, WE), Lower Data Select (LDS), IRQ, and XIRQ. When not used for any of these specific functions, Port E pins 7-2 can be used as general purpose I/O and pins 1-0 can be used as general purpose inputs. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Pins 6 and 5 are inputs with enabled pull-down devices while RESET pin is low. Pins 7 and 3 are inputs with enabled pull-up devices while RESET pin is low. MC9S12XDP512 Data Sheet, Rev. 2.21 832 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.10 Port E Data Direction Register (DDRE) 7 6 5 4 3 2 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 0 0 0 0 0 0 R 1 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 22-12. Port E Data Direction Register (DDRE) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-13. DDRE Field Descriptions Field Description 7-0 DDRE[7:2] Data Direction Port E -- his register controls the data direction for port E. When Port E is operating as a general purpose I/O port, DDRE determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. Port E bit 1 (associated with IRQ) and bit 0 (associated with XIRQ) cannot be configured as outputs. Port E, bits 1 and 0, can be read regardless of whether the alternate interrupt function is enabled. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTE after changing the DDRE register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 833 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.11 S12X_EBI Ports, BKGD, VREGEN Pin Pull-up Control Register (PUCR) 7 6 PUPKE BKPUE 1 1 5 R 4 3 2 1 0 PUPEE PUPDE PUPCE PUPBE PUPAE 1 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 22-13. S12X_EBI Ports, BKGD, VREGEN Pin Pull-up Control Register (PUCR) Read: Anytime in single-chip modes. Write: Anytime, except BKPUE which is writable in special test mode only. This register is used to enable pull-up devices for the associated ports A, B, C, D, E, and K. Pull-up devices are assigned on a per-port basis and apply to any pin in the corresponding port that is currently configured as an input. Table 22-14. PUCR Field Descriptions Field Description 7 PUPKE Pull-up Port K Enable 0 Port K pull-up devices are disabled. 1 Enable pull-up devices for Port K input pins. 6 BKPUE BKGD and VREGEN Pin Pull-up Enable 0 BKGD and VREGEN pull-up devices are disabled. 1 Enable pull-up devices on BKGD and VREGEN pins. 4 PUPEE Pull-up Port E Enable 0 Port E pull-up devices on bit 7, 4-0 are disabled. 1 Enable pull-up devices for Port E input pins bits 7, 4-0. Note: Bits 5 and 6 of Port E have pull-down devices which are only enabled during reset. This bit has no effect on these pins. 3 PUPDE Pull-up Port D Enable 0 Port D pull-up devices are disabled. 1 Enable pull-up devices for all Port D input pins. 2 PUPCE Pull-up Port C Enable 0 Port C pull-up devices are disabled. 1 Enable pull-up devices for all Port C input pins. 1 PUPBE Pull-up Port B Enable 0 Port B pull-up devices are disabled. 1 Enable pull-up devices for all Port B input pins. 0 PUPAE Pull-up Port A Enable 0 Port A pull-up devices are disabled. 1 Enable pull-up devices for all Port A input pins. MC9S12XDP512 Data Sheet, Rev. 2.21 834 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.12 S12X_EBI Ports Reduced Drive Register (RDRIV) 7 R 6 5 0 0 RDPK 4 3 2 1 0 RDPE RDPD RDPC RDPB RDPA 0 0 0 0 0 W Reset 0 0 0 = Unimplemented or Reserved Figure 22-14. S12X_EBI Ports Reduced Drive Register (RDRIV) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. This register is used to select reduced drive for the pins associated with the S12X_EBI ports A, B, C, D, E, and K. If enabled, the pins drive at about 1/6 of the full drive strength. The reduced drive function is independent of which function is being used on a particular pin. The reduced drive functionality does not take effect on the pins in emulation modes. Table 22-15. RDRIV Field Descriptions Field Description 7 RDPK Reduced Drive of Port K 0 All port K output pins have full drive enabled. 1 All port K output pins have reduced drive enabled. 4 RDPE Reduced Drive of Port E 0 All port E output pins have full drive enabled. 1 All port E output pins have reduced drive enabled. 3 RDPD Reduced Drive of Port D 0 All port D output pins have full drive enabled. 1 All port D output pins have reduced drive enabled. 2 RDPC Reduced Drive of Port C 0 All port C output pins have full drive enabled. 1 All port C output pins have reduced drive enabled. 1 RDPB Reduced Drive of Port B 0 All port B output pins have full drive enabled. 1 All port B output pins have reduced drive enabled. 0 RDPA Reduced Drive of Ports A 0 All Port A output pins have full drive enabled. 1 All port A output pins have reduced drive enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 835 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.13 ECLK Control Register (ECLKCTL) 7 6 1 0 NECLK NCLKX2 EDIV1 EDIV0 Mode Dependent 1 0 0 0 0 0 0 Mode 0 1 0 0 0 0 0 0 Special Single-Chip 1 1 0 0 0 0 0 0 Emulation Single-Chip 0 1 0 0 0 0 0 0 Special Test 0 1 0 0 0 0 0 0 Emulation Expanded 1 1 0 0 0 0 0 0 Normal Single-Chip 0 1 0 0 0 0 0 0 Normal Expanded R 5 4 3 2 0 0 0 0 W Reset1 SS ES ST EX NS NX = Unimplemented or Reserved Figure 22-15. ECLK Control Register (ECLKCTL) 1 Reset values in emulation modes are identical to those of the target mode. Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. The ECLKCTL register is used to control the availability of the free-running clocks and the free-running clock divider. Table 22-16. ECLKCTL Field Descriptions Field 7 NECLK Description No ECLK -- This bit controls the availability of a free-running clock on the ECLK pin. Clock output is always active in emulation modes and if enabled in all other operating modes. 0 ECLK enabled 1 ECLK disabled MC9S12XDP512 Data Sheet, Rev. 2.21 836 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-16. ECLKCTL Field Descriptions (continued) Field Description 6 NCLKX2 No ECLKX2 -- This bit controls the availability of a free-running clock on the ECLKX2 pin. This clock has a fixed rate of twice the internal bus clock. Clock output is always active in emulation modes and if enabled in all other operating modes. 0 ECLKX2 is enabled 1 ECLKX2 is disabled 1-0 EDIV[1:0] Free-Running ECLK Divider -- These bits determine the rate of the free-running clock on the ECLK pin. The usage of the bits is shown in Table 22-17. Divider is always disabled in emulation modes and active as programmed in all other operating modes. Table 22-17. Free-Running ECLK Clock Rate EDIV[1:0] Rate of Free-Running ECLK 00 ECLK = Bus clock rate 01 ECLK = Bus clock rate divided by 2 10 ECLK = Bus clock rate divided by 3 11 ECLK = Bus clock rate divided by 4 22.3.2.14 IRQ Control Register (IRQCR) 7 6 IRQE IRQEN 0 1 R 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 22-16. IRQ Control Register (IRQCR) Read: See individual bit descriptions below. Write: See individual bit descriptions below. Table 22-18. IRQCR Field Descriptions Field 7 IRQE 6 IRQEN Description IRQ Select Edge Sensitive Only Special modes: Read or write anytime. Normal and emulation modes: Read anytime, write once. 0 IRQ configured for low level recognition. 1 IRQ configured to respond only to falling edges. Falling edges on the IRQ pin will be detected anytime IRQE = 1 and will be cleared only upon a reset or the servicing of the IRQ interrupt. External IRQ Enable Read or write anytime. 0 External IRQ pin is disconnected from interrupt logic. 1 External IRQ pin is connected to interrupt logic. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 837 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.15 Port K Data Register (PORTK) 7 6 5 4 3 2 1 0 PK7 PK6 PK5 PK4 PK3 PK2 PK1 PK0 Alt. Func. ROMCTL or EWAIT ADDR22 mux NOACC ADDR21 ADDR20 ADDR19 mux IQSTAT3 ADDR18 mux IQSTAT2 ADDR17 mux IQSTAT1 ADDR16 mux IQSTAT0 Reset 0 0 0 0 0 0 0 0 R W Figure 22-17. Port K Data Register (PORTK) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 22-19. PORTK Field Descriptions Field Description 7-0 PK[7:0] Port K -- Port K pins 7-0 are associated with external bus control signals and internal memory expansion emulation pins. These include ADDR22-ADDR16, No-Access (NOACC), External Wait (EWAIT) and instruction pipe signals IQSTAT3-IQSTAT0. Bits 6-0 carry the external addresses in all expanded modes. In emulation or special test mode with internal visibility enabled the address is multiplexed with the alternate functions NOACC and IQSTAT on the respective pins. In single-chip modes the port pins can be used as general-purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 22.3.2.16 Port K Data Direction Register (DDRK) 7 6 5 4 3 2 1 0 DDRK7 DDRK6 DDRK5 DDRK4 DDRK3 DDRK2 DDRK1 DDRK0 0 0 0 0 0 0 0 0 R W Reset Figure 22-18. Port K Data Direction Register (DDRK) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. This register controls the data direction for port K. When Port K is operating as a general purpose I/O port, DDRK determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. MC9S12XDP512 Data Sheet, Rev. 2.21 838 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-20. DDRK Field Descriptions Field Description 7-0 DDRK[7:0] Data Direction Port K 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTK after changing the DDRK register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 839 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.17 Port T Data Register (PTT) 7 6 5 4 3 2 1 0 PTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0 IOC7 IOC6 IOC5 IOC4 IOC3 IOC2 IOC1 IOC0 0 0 0 0 0 0 0 0 R W ECT Reset Figure 22-19. Port T Data Register (PTT) Read: Anytime. Write: Anytime. Table 22-21. PTT Field Descriptions Field Description 7-0 PTT[7:0] Port T -- Port T bits 7-0 are associated with ECT channels IOC7-IOC0 (refer to ECT section). When not used with the ECT, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 22.3.2.18 Port T Input Register (PTIT) R 7 6 5 4 3 2 1 0 PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 22-20. Port T Input Register (PTIT) 1 These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. Table 22-22. PTIT Field Descriptions Field Description 7-0 PTIT[7:0] Port T Input -- This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. MC9S12XDP512 Data Sheet, Rev. 2.21 840 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.19 Port T Data Direction Register (DDRT) 7 6 5 4 3 2 1 0 DDRT7 DDRT6 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0 0 0 0 0 0 0 0 0 R W Reset Figure 22-21. Port T Data Direction Register (DDRT) Read: Anytime. Write: Anytime. This register configures each port T pin as either input or output. The ECT forces the I/O state to be an output for each timer port associated with an enabled output compare. In this case the data direction bits will not change. The DDRT bits revert to controlling the I/O direction of a pin when the associated timer output compare is disabled. The timer input capture always monitors the state of the pin. Table 22-23. DDRT Field Descriptions Field Description 7-0 DDRT[7:0] Data Direction Port T 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTT or PTIT registers, when changing the DDRT register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 841 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.20 Port T Reduced Drive Register (RDRT) 7 6 5 4 3 2 1 0 RDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0 0 0 0 0 0 0 0 0 R W Reset Figure 22-22. Port T Reduced Drive Register (RDRT) Read: Anytime. Write: Anytime. This register configures the drive strength of each port T output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-24. RDRT Field Descriptions Field 7-0 RDRT[7:0] Description Reduced Drive Port T 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.21 Port T Pull Device Enable Register (PERT) 7 6 5 4 3 2 1 0 PERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0 0 0 0 0 0 0 0 0 R W Reset Figure 22-23. Port T Pull Device Enable Register (PERT) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 22-25. PERT Field Descriptions Field 7-0 PERT[7:0] Description Pull Device Enable Port T 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 842 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.22 Port T Polarity Select Register (PPST) 7 6 5 4 3 2 1 0 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0 0 0 0 0 0 0 0 R W Reset Figure 22-24. Port T Polarity Select Register (PPST) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. Table 22-26. PPST Field Descriptions Field Description 7-0 PPST[7:0] Pull Select Port T 0 A pull-up device is connected to the associated port T pin, if enabled by the associated bit in register PERT and if the port is used as input. 1 A pull-down device is connected to the associated port T pin, if enabled by the associated bit in register PERT and if the port is used as input. 22.3.2.23 Port S Data Register (PTS) 7 6 5 4 3 2 1 0 PTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0 SS0 SCK0 MOSI0 MISO0 TXD1 RXD1 TXD0 RXD0 0 0 0 0 0 0 0 0 R W SCI/SPI Reset Figure 22-25. Port S Data Register (PTS) Read: Anytime. Write: Anytime. Port S pins 7-4 are associated with the SPI0. The SPI0 pin configuration is determined by several status bits in the SPI0 module. Refer to SPI section for details. When not used with the SPI0, these pins can be used as general purpose I/O. Port S bits 3-0 are associated with the SCI1 and SCI0. The SCI ports associated with transmit pins 3 and 1 are configured as outputs if the transmitter is enabled. The SCI ports associated with receive pins 2 and 0 are configured as inputs if the receiver is enabled. Refer to SCI section for details. When not used with the SCI, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 843 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.24 Port S Input Register (PTIS) R 7 6 5 4 3 2 1 0 PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 22-26. Port S Input Register (PTIS) 1 These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This also can be used to detect overload or short circuit conditions on output pins. MC9S12XDP512 Data Sheet, Rev. 2.21 844 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.25 Port S Data Direction Register (DDRS) 7 6 5 4 3 2 1 0 DDRS7 DDRS6 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0 0 0 0 0 0 0 0 0 R W Reset Figure 22-27. Port S Data Direction Register (DDRS) Read: Anytime. Write: Anytime. This register configures each port S pin as either input or output. If SPI0 is enabled, the SPI0 determines the pin direction. Refer to SPI section for details. If the associated SCI transmit or receive channel is enabled this register has no effect on the pins. The pin is forced to be an output if a SCI transmit channel is enabled, it is forced to be an input if the SCI receive channel is enabled. The DDRS bits revert to controlling the I/O direction of a pin when the associated channel is disabled. Table 22-27. DDRS Field Descriptions Field Description 7-0 DDRS[7:0] Data Direction Port S 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTS or PTIS registers, when changing the DDRS register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 845 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.26 Port S Reduced Drive Register (RDRS) 7 6 5 4 3 2 1 0 RDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0 0 0 0 0 0 0 0 0 R W Reset Figure 22-28. Port S Reduced Drive Register (RDRS) Read: Anytime. Write: Anytime. This register configures the drive strength of each port S output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-28. RDRS Field Descriptions Field 7-0 RDRS[7:0] Description Reduced Drive Port S 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.27 Port S Pull Device Enable Register (PERS) 7 6 5 4 3 2 1 0 PERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0 1 1 1 1 1 1 1 1 R W Reset Figure 22-29. Port S Pull Device Enable Register (PERS) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or as output in wired-OR (open drain) mode. This bit has no effect if the port is used as push-pull output. Out of reset a pull-up device is enabled. Table 22-29. PERS Field Descriptions Field 7-0 PERS[7:0] Description Pull Device Enable Port S 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 846 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.28 Port S Polarity Select Register (PPSS) 7 6 5 4 3 2 1 0 PPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0 0 0 0 0 0 0 0 0 R W Reset Figure 22-30. Port S Polarity Select Register (PPSS) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. Table 22-30. PPSS Field Descriptions Field Description 7-0 PPSS[7:0] Pull Select Port S 0 A pull-up device is connected to the associated port S pin, if enabled by the associated bit in register PERS and if the port is used as input or as wired-OR output. 1 A pull-down device is connected to the associated port S pin, if enabled by the associated bit in register PERS and if the port is used as input. 22.3.2.29 Port S Wired-OR Mode Register (WOMS) 7 6 5 4 3 2 1 0 WOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0 0 0 0 0 0 0 0 0 R W Reset Figure 22-31. Port S Wired-OR Mode Register (WOMS) Read: Anytime. Write: Anytime. This register configures the output pins as wired-OR. If enabled the output is driven active low only (open-drain). A logic level of "1" is not driven. It applies also to the SPI and SCI outputs and allows a multipoint connection of several serial modules. These bits have no influence on pins used as inputs. Table 22-31. WOMS Field Descriptions Field Description 7-0 Wired-OR Mode Port S WOMS[7:0] 0 Output buffers operate as push-pull outputs. 1 Output buffers operate as open-drain outputs. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 847 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.30 Port M Data Register (PTM) 7 6 5 4 3 2 1 0 PTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0 TXCAN3 RXCAN3 TXCAN2 RXCAN2 TXCAN1 RXCAN1 TXCAN0 RXCAN0 TXCAN0 RXCAN0 TXCAN0 RXCAN0 TXCAN4 RXCAN4 SCK0 MOSI0 SS0 MISO0 0 0 0 0 0 0 R W CAN Routed CAN0 Routed CAN4 TXCAN4 RXCAN4 Routed SPIO Reset 0 0 Figure 22-32. Port M Data Register (PTM) Read: Anytime. Write: Anytime. Port M pins 75-0 are associated with the CAN0, CAN1, CAN2, CAN3, SCI3, as well as the routed CAN0, CAN4, and SPI0 modules. When not used with any of the peripherals, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Table 22-32. PTM Field Descriptions Field Description 7-6 PTM[7:6] The CAN3 function (TXCAN3 and RXCAN3) takes precedence over the CAN4, SCI3 and the general purpose I/O function if the CAN3 module is enabled. Refer to MSCAN section for details. The CAN4 function (TXCAN4 and RXCAN4) takes precedence over the SCI3 and the general purpose I/O function if the CAN4 module is enabled. Refer to MSCAN section for details. The SCI3 function (TXD3 and RXD3) takes precedence over the general purpose I/O function if the SCI3 module is enabled. Refer to SCI section for details. 5-4 PTM[5:4] The CAN2 function (TXCAN2 and RXCAN2) takes precedence over the routed CAN0, routed CAN4, the routed SPI0 and the general purpose I/O function if the CAN2 module is enabled{pim_9xd_prio.m}. The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the routed CAN4, the routed SPI0 and the general purpose I/O function if the routed CAN0 module is enabled. The routed CAN4 function (TXCAN4 and RXCAN4) takes precedence over the routed SPI0 and general purpose I/O function if the routed CAN4 module is enabled. Refer to MSCAN section for details. The routed SPI0 function (SCK0 and MOSI0) takes precedence of the general purpose I/O function if the routed SPI0 is enabled. Refer to SPI section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 848 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-32. PTM Field Descriptions (continued) Field Description 3-2 PTM[3:2] The CAN1 function (TXCAN1 and RXCAN1) takes precedence over the routed CAN0, the routed SPI0 and the general purpose I/O function if the CAN1 module is enabled. The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the routed SPI0 and the general purpose I/O function if the routed CAN0 module is enabled. Refer to MSCAN section for details. The routed SPI0 function (SS0 and MISO0) takes precedence of the general purpose I/O function if the routed SPI0 is enabled and not in bidirectional mode. Refer to SPI section for details. 1-0 PTM[1:0] The CAN0 function (TXCAN0 and RXCAN0) takes precedence over the general purpose I/O function if the CAN0 module is enabled. Refer to MSCAN section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 849 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.31 Port M Input Register (PTIM) R 7 6 5 4 3 2 1 0 PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 22-33. Port M Input Register (PTIM) 1 These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. MC9S12XDP512 Data Sheet, Rev. 2.21 850 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.32 Port M Data Direction Register (DDRM) 7 6 5 4 3 2 1 0 DDRM7 DDRM6 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0 0 0 0 0 0 0 0 0 R W Reset Figure 22-34. Port M Data Direction Register (DDRM) Read: Anytime. Write: Anytime. This register configures each port M pin as either input or output. The CAN/SCI3 forces the I/O state to be an output for each port line associated with an enabled output (TXCAN[3:0], TXD3). TheyAlso forces the I/O state to be an input for each port line associated with an enabled input (RXCAN[3:0], RXD3). In those cases the data direction bits will not change. The DDRM bits revert to controlling the I/O direction of a pin when the associated peripheral module is disabled. Table 22-33. DDRM Field Descriptions Field Description 7-0 DDRM[7:0] Data Direction Port M 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTM or PTIM registers, when changing the DDRM register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 851 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.33 Port M Reduced Drive Register (RDRM) 7 6 5 4 3 2 1 0 RDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0 0 0 0 0 0 0 0 0 R W Reset Figure 22-35. Port M Reduced Drive Register (RDRM) Read: Anytime. Write: Anytime. This register configures the drive strength of each Port M output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-34. RDRM Field Descriptions Field 7-0 RDRM[7:0] Description Reduced Drive Port M 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.34 Port M Pull Device Enable Register (PERM) 7 6 5 4 3 2 1 0 PERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0 0 0 0 0 0 0 0 0 R W Reset Figure 22-36. Port M Pull Device Enable Register (PERM) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset no pull device is enabled. Table 22-35. PERM Field Descriptions Field 7-0 PERM[7:0] Description Pull Device Enable Port M 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 852 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.35 Port M Polarity Select Register (PPSM) 7 6 5 4 3 2 1 0 PPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0 0 0 0 0 0 0 0 0 R W Reset Figure 22-37. Port M Polarity Select Register (PPSM) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. If CAN is active a pull-up device can be activated on the RXCAN[3:0] inputs, but not a pull-down. Table 22-36. PPSM Field Descriptions Field Description 7-0 PPSM[7:0] Pull Select Port M 0 A pull-up device is connected to the associated port M pin, if enabled by the associated bit in register PERM and if the port is used as general purpose or RXCAN input. 1 A pull-down device is connected to the associated port M pin, if enabled by the associated bit in register PERM and if the port is used as a general purpose but not as RXCAN. 22.3.2.36 Port M Wired-OR Mode Register (WOMM) 7 6 5 4 3 2 1 0 WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 0 0 0 0 0 0 0 0 R W Reset Figure 22-38. Port M Wired-OR Mode Register (WOMM) Read: Anytime. Write: Anytime. This register configures the output pins as wired-OR. If enabled the output is driven active low only (open-drain). A logic level of "1" is not driven. It applies also to the CAN outputs and allows a multipoint connection of several serial modules. This bit has no influence on pins used as inputs. Table 22-37. WOMM Field Descriptions Field Description 7-0 Wired-OR Mode Port M WOMM[7:0] 0 Output buffers operate as push-pull outputs. 1 Output buffers operate as open-drain outputs. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 853 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.37 Module Routing Register (MODRR) 7 R 6 5 4 3 2 1 0 MODRR6 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0 0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 22-39. Module Routing Register (MODRR) Read: Anytime. Write: Anytime. This register configures the re-routing of CAN0, CAN4, SPI0, SPI1, and SPI2 on alternative ports. Table 22-38. Module Routing Summary MODRR Related Pins Module CAN0 CAN4 6 5 4 3 2 1 0 RXCAN TXCAN x x x x x 0 0 PM0 PM1 x x x x x 0 1 PM2 PM3 x x x x x 1 0 PM4 PM5 x x x x x 1 1 PJ6 PJ7 x x x 0 0 x x PJ6 PJ7 x x x 0 1 x x PM4 PM5 x x x 1 0 x x PM6 PM7 x x x 1 1 x x Reserved MISO SPI0 SPI1 SPI2 MOSI SCK SS x x 0 x x x x PS4 PS5 PS6 PS7 x x 1 x x x x PM2 PM4 PM5 PM3 x 0 x x x x x PP0 PP1 PP2 PP3 x 1 x x x x x PH0 PH1 PH2 PH3 0 x x x x x x PP4 PP5 PP7 PP6 1 x x x x x x PH4 PH5 PH6 PH7 MC9S12XDP512 Data Sheet, Rev. 2.21 854 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.38 Port P Data Register (PTP) 7 6 5 4 3 2 1 0 PTP7 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0 PWM PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 SPI SCK2 SS2 MOSI2 MISO2 SS1 SCK1 MOSI1 MISO1 0 0 0 0 0 0 0 0 R W Reset Figure 22-40. Port P Data Register (PTP) Read: Anytime. Write: Anytime. Port P pins 7, and 5-0 are associated with the PWM as well as the SPI1 and SPI2 modules. These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. The PWM function takes precedence over the general purpose I/O and the SPI2 or SPI1 function if the associated PWM channel is enabled. While channels 6 and 5-0 are output only if the respective channel is enabled, channel 7 can be PWM output or input if the shutdown feature is enabled. Refer to PWM section for details. The SPI2 function takes precedence over the general purpose I/O function if enabled. Refer to SPI section for details. The SPI1 function takes precedence over the general purpose I/O function if enabled. Refer to SPI section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 855 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.39 Port P Input Register (PTIP) R 7 6 5 4 3 2 1 0 PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 22-41. Port P Input Register (PTIP) 1 These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. MC9S12XDP512 Data Sheet, Rev. 2.21 856 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.40 Port P Data Direction Register (DDRP) 7 6 5 4 3 2 1 0 DDRP7 DDRP6 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0 0 0 0 0 0 0 0 0 R W Reset Figure 22-42. Port P Data Direction Register (DDRP) Read: Anytime. Write: Anytime. This register configures each port P pin as either input or output. If the associated PWM channel or SPI module is enabled this register has no effect on the pins. The PWM forces the I/O state to be an output for each port line associated with an enabled PWM7-0 channel. Channel 7 can force the pin to input if the shutdown feature is enabled. Refer to PWM section for details. If a SPI module is enabled, the SPI determines the pin direction. Refer to SPI section for details. The DDRP bits revert to controlling the I/O direction of a pin when the associated peripherals are disabled. Table 22-39. DDRP Field Descriptions Field Description 7-0 DDRP[7:0] Data Direction Port P 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTP or PTIP registers, when changing the DDRP register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 857 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.41 Port P Reduced Drive Register (RDRP) 7 6 5 4 3 2 1 0 RDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0 0 0 0 0 0 0 0 0 R W Reset Figure 22-43. Port P Reduced Drive Register (RDRP) Read: Anytime. Write: Anytime. This register configures the drive strength of each port P output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-40. RDRP Field Descriptions Field 7-0 RDRP[7:0] Description Reduced Drive Port P 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.42 Port P Pull Device Enable Register (PERP) 7 6 5 4 3 2 1 0 PERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0 0 0 0 0 0 0 0 0 R W Reset Figure 22-44. Port P Pull Device Enable Register (PERP) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 22-41. PERP Field Descriptions Field 7-0 PERP[7:0] Description Pull Device Enable Port P 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 858 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.43 Port P Polarity Select Register (PPSP) 7 6 5 4 3 2 1 0 PPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSP0 0 0 0 0 0 0 0 0 R W Reset Figure 22-45. Port P Polarity Select Register (PPSP) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. Table 22-42. PPSP Field Descriptions Field Description 7-0 PPSP[7:0] Polarity Select Port P 0 Falling edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-up device is connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is used as input. 1 Rising edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-down device is connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is used as input. 22.3.2.44 Port P Interrupt Enable Register (PIEP) 7 6 5 4 3 2 1 0 PIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0 0 0 0 0 0 0 0 0 R W Reset Figure 22-46. Port P Interrupt Enable Register (PIEP) Read: Anytime. Write: Anytime. This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port P. Table 22-43. PIEP Field Descriptions Field 7-0 PIEP[7:0] Description Interrupt Enable Port P 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 859 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.45 Port P Interrupt Flag Register (PIFP) 7 6 5 4 3 2 1 0 PIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0 0 0 0 0 0 0 0 0 R W Reset Figure 22-47. Port P Interrupt Flag Register (PIFP) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSP register. To clear this flag, write logic level "1" to the corresponding bit in the PIFP register. Writing a "0" has no effect. Table 22-44. PIFP Field Descriptions Field 7-0 PIFP[7:0] Description Interrupt Flags Port P 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. MC9S12XDP512 Data Sheet, Rev. 2.21 860 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.46 Port H Data Register (PTH) 7 6 5 4 3 2 1 0 PTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0 SS2 SCK2 MOSI2 MISO2 SS1 SCK1 MOSI1 MISO1 0 0 0 0 0 0 0 0 R W Routed SPI Reset Figure 22-48. Port H Data Register (PTH) Read: Anytime. Write: Anytime. Port H pins 7-0 are associated with the SCI4 and SCI5 as well as the routed SPI1 and SPI2 modules. These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. The routed SPI2 function takes precedence over the SCI4 and SCI5 and the general purpose I/O function if the routed SPI2 module is enabled. Refer to SPI section for details. The routed SPI1 function takes precedence over the general purpose I/O function if the routed SPI1 is enabled. Refer to SPI section for details. The SCI4 and SCI5 function takes precedence over the general purpose I/O function if the SCI4 or SCI5 is enabled. Refer to SCI section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 861 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.47 Port H Input Register (PTIH) R 7 6 5 4 3 2 1 0 PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 22-49. Port H Input Register (PTIH) 1 These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. MC9S12XDP512 Data Sheet, Rev. 2.21 862 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.48 Port H Data Direction Register (DDRH) 7 6 5 4 3 2 1 0 DDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 0 0 0 0 0 0 0 0 R W Reset Figure 22-50. Port H Data Direction Register (DDRH) Read: Anytime. Write: Anytime. This register configures each port H pin as either input or output. If the associated SCI channel or routed SPI module is enabled this register has no effect on the pins. The SCI forces the I/O state to be an output for each port line associated with an enabled output (TXD5, TXD4). It also forces the I/O state to be an input for each port line associated with an enabled input (RXD5, RXD4). In those cases the data direction bits will not change. If a SPI module is enabled, the SPI determines the pin direction. Refer to SPI section for details. The DDRH bits revert to controlling the I/O direction of a pin when the associated peripheral modules are disabled. Table 22-45. DDRH Field Descriptions Field Description 7-0 DDRH[7:0] Data Direction Port H 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTH or PTIH registers, when changing the DDRH register. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 863 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.49 Port H Reduced Drive Register (RDRH) 7 6 5 4 3 2 1 0 RDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0 0 0 0 0 0 0 0 0 R W Reset Figure 22-51. Port H Reduced Drive Register (RDRH) Read: Anytime. Write: Anytime. This register configures the drive strength of each Port H output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-46. RDRH Field Descriptions Field 7-0 RDRH[7:0] Description Reduced Drive Port H 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.50 Port H Pull Device Enable Register (PERH) 7 6 5 4 3 2 1 0 PERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0 0 0 0 0 0 0 0 0 R W Reset Figure 22-52. Port H Pull Device Enable Register (PERH) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 22-47. PERH Field Descriptions Field 7-0 PERH[7:0] Description Pull Device Enable Port H 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 864 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.51 Port H Polarity Select Register (PPSH) 7 6 5 4 3 2 1 0 PPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0 0 0 0 0 0 0 0 0 R W Reset Figure 22-53. Port H Polarity Select Register (PPSH) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. Table 22-48. PPSH Field Descriptions Field Description 7-0 PPSH[7:0] Polarity Select Port H 0 Falling edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-up device is connected to the associated port H pin, if enabled by the associated bit in register PERH and if the port is used as input. 1 Rising edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-down device is connected to the associated port H pin, if enabled by the associated bit in register PERH and if the port is used as input. 22.3.2.52 Port H Interrupt Enable Register (PIEH) 7 6 5 4 3 2 1 0 PIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0 0 0 0 0 0 0 0 0 R W Reset Figure 22-54. Port H Interrupt Enable Register (PIEH) Read: Anytime. Write: Anytime. This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port H. Table 22-49. PIEH Field Descriptions Field 7-0 PIEH[7:0] Description Interrupt Enable Port H 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 865 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.53 Port H Interrupt Flag Register (PIFH) 7 6 5 4 3 2 1 0 PIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0 0 0 0 0 0 0 0 0 R W Reset Figure 22-55. Port H Interrupt Flag Register (PIFH) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSH register. To clear this flag, write logic level "1" to the corresponding bit in the PIFH register. Writing a "0" has no effect. Table 22-50. PIFH Field Descriptions Field 7-0 PIFH[7:0] Description Interrupt Flags Port H 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. MC9S12XDP512 Data Sheet, Rev. 2.21 866 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.54 Port J Data Register (PTJ) 7 6 5 4 PTJ7 PTJ6 PTJ5 PTJ4 TXCAN4 RXCAN4 SCL0 SDA0 R 3 2 1 0 PTJ2 PTJ1 PTJ0 TXD2 RXD2 0 W CAN4/ SCI2 IICO IIC1 Routed CAN0 TXCAN0 SDA1 CS2 CS0 0 0 RXCAN0 Alt. Function Reset SCL1 0 0 CS1 0 0 CS3 0 0 = Unimplemented or Reserved Figure 22-56. Port J Data Register (PTJ) Read: Anytime. Write: Anytime. Port J pins 7-4 and 2-0 are associated with the CAN4, SCI2, IIC0 and IIC1, the routed CAN0 modules and chip select signals (CS0, CS1, CS2, CS3). These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Table 22-51. PTJ Field Descriptions Field Description 7-6 PJ[7:0] The CAN4 function (TXCAN4 and RXCAN4) takes precedence over the IIC0, the routed CAN0 and the general purpose I/O function if the CAN4 module is enabled. The IIC0 function (SCL0 and SDA0) takes precedence over the routed CAN0 and the general purpose I/O function if the IIC0 is enabled. If the IIC0 module takes precedence the SDA0 and SCL0 outputs are configured as open drain outputs. Refer to IIC section for details. The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the general purpose I/O function if the routed CAN0 module is enabled. Refer to MSCAN section for details. 5-4 PJ[5:4] 2 PJ2 The IIC1 function (SCL1 and SDA1) takes precedence over the chip select (CS0, CS2) and general purpose I/O function if the IIC1 is enabled. The chip selects (CS0, CS2) take precedence over the general purpose I/O. If the IIC1 module takes precedence the SDA1 and SCL1 outputs are configured as open drain outputs. Refer to IIC section for details. The chip select function (CS1) takes precedence over the general purpose I/O. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 867 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-51. PTJ Field Descriptions (continued) Field Description 1 PJ1 The SCI2 function takes precedence over the general purpose I/O function if the SCI2 module is enabled. Refer to SCI section for details. 0 PJ0 The SCI2 function takes precedence over the chip select (CS3) and the general purpose I/O function if the SCI2 module is enabled. The chip select (CS3) takes precedence over the general purpose I/O function. Refer to SCI section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 868 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.55 Port J Input Register (PTIJ) R 7 6 5 4 3 2 1 0 PTIJ7 PTIJ6 PTIJ5 PTIJ4 0 PTIJ2 PTIJ1 PTIJ0 0 0 0 0 0 0 0 0 W Reset1 = Unimplemented or Reserved Figure 22-57. Port J Input Register (PTIJ) 1 These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can be used to detect overload or short circuit conditions on output pins. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 869 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.56 Port J Data Direction Register (DDRJ) 7 6 5 4 3 DDRJ7 DDRJ6 DDRJ5 DDRJ4 0 0 0 0 R 2 1 0 DDRJ2 DDRJ1 DDRJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 22-58. Port J Data Direction Register (DDRJ) Read: Anytime. Write: Anytime. This register configures each port J pin as either input or output. The CAN forces the I/O state to be an output on PJ7 (TXCAN4) and an input on pin PJ6 (RXCAN4). The IIC takes control of the I/O if enabled. In these cases the data direction bits will not change. The SCI2 forces the I/O state to be an output for each port line associated with an enabled output (TXD2). It also forces the I/O state to be an input for each port line associated with an enabled input (RXD2). In these cases the data direction bits will not change. The DDRJ bits revert to controlling the I/O direction of a pin when the associated peripheral module is disabled. Table 22-52. DDRJ Field Descriptions Field Description 7-0 DDRJ[7:4] DDRJ[2:0] Data Direction Port J 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTJ or PTIJ registers, when changing the DDRJ register. MC9S12XDP512 Data Sheet, Rev. 2.21 870 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.57 Port J Reduced Drive Register (RDRJ) 7 6 5 4 3 RDRJ7 RDRJ6 RDRJ5 RDRJ4 0 0 0 0 R 2 1 0 RDRJ2 RDRJ1 RDRJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 22-59. Port J Reduced Drive Register (RDRJ) Read: Anytime. Write: Anytime. This register configures the drive strength of each port J output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-53. RDRJ Field Descriptions Field 7-0 RDRJ[7:4] RDRJ[2:0] Description Reduced Drive Port J 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.58 Port J Pull Device Enable Register (PERJ) 7 6 5 4 3 PERJ7 PERJ6 PERJ5 PERJ4 1 1 1 1 R 2 1 0 PERJ2 PERJ1 PERJ0 1 1 1 0 W Reset 0 = Unimplemented or Reserved Figure 22-60. Port J Pull Device Enable Register (PERJ) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or as wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset a pull-up device is enabled. Table 22-54. PERJ Field Descriptions Field 7-0 PERJ[7:4] PERJ[2:0] Description Pull Device Enable Port J 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 871 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.59 Port J Polarity Select Register (PPSJ) 7 6 5 4 3 PPSJ7 PPSJ6 PPSJ5 PPSJ4 0 0 0 0 R 2 1 0 PPSJ2 PPSJ1 PPSJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 22-61. Port J Polarity Select Register (PPSJ) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. Table 22-55. PPSJ Field Descriptions Field Description 7-0 PPSJ[7:4] PPSJ[2:0] Polarity Select Port J 0 Falling edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-up device is connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is used as general purpose input or as IIC port. 1 Rising edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-down device is connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is used as input. 22.3.2.60 Port J Interrupt Enable Register (PIEJ) 7 6 5 4 PIEJ7 PIEJ6 PIEJ5 PIEJ4 0 0 0 0 R 3 2 1 0 PIEJ2 PIEJ1 PIEJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 22-62. Port J Interrupt Enable Register (PIEJ) This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port J. Table 22-56. PIEJ Field Descriptions Field 7-0 PIEJ[7:4] PIEJ[2:0] Description Interrupt Enable Port J 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 872 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.61 Port J Interrupt Flag Register (PIFJ) 7 6 5 4 PIFJ7 PIFJ6 PIFJ5 PIFJ4 0 0 0 0 3 R 2 1 0 PIFJ2 PIFJ1 PIFJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 22-63. Port J Interrupt Flag Register (PIFJ) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSJ register. To clear this flag, write logic level "1" to the corresponding bit in the PIFJ register. Writing a "0" has no effect. Table 22-57. PIEJ Field Descriptions Field 7-0 PIFJ[7:4] PIFJ[2:0] Description Interrupt Flags Port J 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. 22.3.2.62 Port AD0 Data Register 1 (PT1AD0) 7 6 5 4 3 2 1 0 PT1AD07 PT1AD06 PT1AD05 PT1AD04 PT1AD03 PT1AD02 PT1AD01 PT1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 22-64. Port AD0 Data Register 1 (PT1AD0) Read: Anytime. Write: Anytime. This register is associated with AD0 pins PAD[7:0]. These pins can also be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 873 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.63 Port AD0 Data Direction Register 1 (DDR1AD0) 7 6 5 4 3 2 1 0 DDR1AD07 DDR1AD06 DDR1AD05 DDR1AD04 DDR1AD03 DDR1AD02 DDR1AD01 DDR1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 22-65. Port AD0 Data Direction Register 1 (DDR1AD0) Read: Anytime. Write: Anytime. This register configures pins PAD[07:00] as either input or output. Table 22-58. DDR1AD0 Field Descriptions Field Description 7-0 DDR1AD0[7:0] Data Direction Port AD0 Register 1 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD01 register, when changing the DDR1AD0 register. Note: To use the digital input function on port AD0 the ATD0 digital input enable register (ATD0DIEN) has to be set to logic level "1". MC9S12XDP512 Data Sheet, Rev. 2.21 874 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.64 Port AD0 Reduced Drive Register 1 (RDR1AD0) 7 6 5 4 3 2 1 0 RDR1AD07 RDR1AD06 RDR1AD05 RDR1AD04 RDR1AD03 RDR1AD02 RDR1AD01 RDR1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 22-66. Port AD0 Reduced Drive Register 1 (RDR1AD0) Read: Anytime. Write: Anytime. This register configures the drive strength of each output pin PAD[07:00] as either full or reduced. If the port is used as input this bit is ignored. Table 22-59. RDR1AD0 Field Descriptions Field Description 7-0 RDR1AD0[7:0] Reduced Drive Port AD0 Register 1 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.65 Port AD0 Pull Up Enable Register 1 (PER1AD0) 7 6 5 4 3 2 1 0 PER1AD07 PER1AD06 PER1AD05 PER1AD04 PER1AD03 PER1AD02 PER1AD01 PER1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 22-67. Port AD0 Pull Up Enable Register 1 (PER1AD0) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective pin PAD[07:00] if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 22-60. PER1AD0 Field Descriptions Field 7-0 PER1AD0[7:0] Description Pull Device Enable Port AD0 Register 1 0 Pull-up device is disabled. 1 Pull-up device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 875 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.66 Port AD1 Data Register 0 (PT0AD1) 7 6 5 4 3 2 1 0 PT0AD123 PT0AD122 PT0AD121 PT0AD120 PT0AD119 PT0AD118 PT0AD117 PT0AD116 0 0 0 0 0 0 0 0 R W Reset Figure 22-68. Port AD1 Data Register 0 (PT0AD1) Read: Anytime. Write: Anytime. This register is associated with AD1 pins PAD[23:16]. These pins can also be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. 22.3.2.67 Port AD1 Data Register 1 (PT1AD1) 7 6 5 4 3 2 1 0 PT1AD115 PT1AD114 PT1AD113 PT1AD112 PT1AD111 PT1AD110 PT1AD19 PT1AD18 0 0 0 0 0 0 0 0 R W Reset Figure 22-69. Port AD1 Data Register 1 (PT1AD1) Read: Anytime. Write: Anytime. This register is associated with AD1 pins PAD[15:08]. These pins can also be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. MC9S12XDP512 Data Sheet, Rev. 2.21 876 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.68 Port AD1 Data Direction Register 0 (DDR0AD1) 7 6 5 4 3 2 1 0 R DDR0AD123 DDR0AD122 DDR0AD121 DDR0AD120 DDR0AD119 DDR0AD118 DDR0AD117 DDR0AD116 W Reset 0 0 0 0 0 0 0 0 Figure 22-70. Port AD1 Data Direction Register 0 (DDR0AD1) Read: Anytime. Write: Anytime. This register configures pin PAD[23:16] as either input or output. Table 22-61. DDR0AD1 Field Descriptions Field Description 7-0 Data Direction Port AD1 Register 0 DDR0AD1[23:16] 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD10 register, when changing the DDR0AD1 register. Note: To use the digital input function on Port AD1 the ATD1 digital input enable register (ATD1DIEN0) has to be set to logic level "1". MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 877 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.69 Port AD1 Data Direction Register 1 (DDR1AD1) 7 6 5 4 3 2 1 0 R DDR1AD115 DDR1AD114 DDR1AD113 DDR1AD112 DDR1AD111 DDR1AD110 DDR1AD19 DDR1AD18 W Reset 0 0 0 0 0 0 0 0 Figure 22-71. Port AD1 Data Direction Register 1 (DDR1AD1) Read: Anytime. Write: Anytime. This register configures pins PAD[15:08] as either input or output. Table 22-62. DDR1AD1 Field Descriptions Field Description 7-0 DDR1AD1[15:8] Data Direction Port AD1 Register 1 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD11 register, when changing the DDR1AD1 register. Note: To use the digital input function on port AD1 the ATD1 digital input enable register (ATD1DIEN1) has to be set to logic level "1". MC9S12XDP512 Data Sheet, Rev. 2.21 878 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.70 Port AD1 Reduced Drive Register 0 (RDR0AD1) 7 6 5 4 3 2 1 0 R RDR0AD123 RDR0AD122 RDR0AD121 RDR0AD120 RDR0AD119 RDR0AD118 RDR0AD117 RDR0AD116 W Reset 0 0 0 0 0 0 0 0 Figure 22-72. Port AD1 Reduced Drive Register 0 (RDR0AD1) Read: Anytime. Write: Anytime. This register configures the drive strength of each PAD[23:16] output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-63. RDR0AD1 Field Descriptions Field Description 7-0 Reduced Drive Port AD1 Register 0 RDR0AD1[23:16] 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 22.3.2.71 Port AD1 Reduced Drive Register 1 (RDR1AD1) 7 6 5 4 3 2 1 0 R RDR1AD115 RDR1AD114 RDR1AD113 RDR1AD112 RDR1AD111 RDR1AD110 RDR1AD19 RDR1AD18 W Reset 0 0 0 0 0 0 0 0 Figure 22-73. Port AD1 Reduced Drive Register 1 (RDR1AD1) Read: Anytime. Write: Anytime. This register configures the drive strength of each PAD[15:08] output pin as either full or reduced. If the port is used as input this bit is ignored. Table 22-64. RDR1AD1 Field Descriptions Field 7-0 RDR1AD1[15:8] Description Reduced Drive Port AD1 Register 1 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 879 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.3.2.72 Port AD1 Pull Up Enable Register 0 (PER0AD1) 7 6 5 4 3 2 1 0 R PER0AD123 PER0AD122 PER0AD121 PER0AD120 PER0AD119 PER0AD118 PER0AD117 PER0AD116 W Reset 0 0 0 0 0 0 0 0 Figure 22-74. Port AD1 Pull Up Enable Register 0 (PER0AD1) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective PAD[23:16] pin if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull-up device is enabled. Table 22-65. PER0AD1 Field Descriptions Field Description 7-0 Pull Device Enable Port AD1 Register 0 PER0AD1[23:16] 0 Pull-up device is disabled. 1 Pull-up device is enabled. 22.3.2.73 Port AD1 Pull Up Enable Register 1 (PER1AD1) 7 6 5 4 3 2 1 0 PER1AD19 PER1AD18 0 0 R PER1AD115 PER1AD114 PER1AD113 PER1AD112 PER1AD111 PER1AD110 W Reset 0 0 0 0 0 0 Figure 22-75. Port AD1 Pull Up Enable Register 1 (PER1AD1) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective PAD[15:08] pin if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull-up device is enabled. Table 22-66. PER1AD1 Field Descriptions Field 7-0 PER1AD1[15:8] Description Pull Device Enable Port AD1 Register 1 0 Pull-up device is disabled. 1 Pull-up device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 880 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.4 Functional Description Each pin except PE0, PE1, and BKGD can act as general purpose I/O. In addition each pin can act as an output from the external bus interface module or a peripheral module or an input to the external bus interface module or a peripheral module. A set of configuration registers is common to all ports with exceptions in the expanded bus interface and ATD ports (Table 22-67). All registers can be written at any time; however a specific configuration might not become active. Example: Selecting a pull-up device This device does not become active while the port is used as a push-pull output. Table 22-67. Register Availability per Port1 1 Port Data Data Direction Input Reduced Drive Pull Enable Polarity Select Wired-OR Mode Interrupt Enable Interrupt Flag A yes yes -- yes yes -- -- -- -- B yes yes -- -- -- -- -- C yes yes -- -- -- -- -- D yes yes -- -- -- -- -- E yes yes -- -- -- -- -- K yes yes -- -- -- -- -- T yes yes yes yes yes -- -- -- -- S yes yes yes yes yes yes yes -- -- M yes yes yes yes yes yes yes -- -- P yes yes yes yes yes yes -- yes yes H yes yes yes yes yes yes -- yes yes J yes yes yes yes yes yes -- yes yes AD0 yes yes -- yes yes -- -- -- -- AD1 yes yes -- yes yes -- -- -- -- Each cell represents one register with individual configuration bits 22.4.1 22.4.1.1 Registers Data Register This register holds the value driven out to the pin if the pin is used as a general purpose I/O. Writing to this register has only an effect on the pin if the pin is used as general purpose output. When reading this address, the buffered state of the pin is returned if the associated data direction register bit is set to "0". If the data direction register bits are set to logic level "1", the contents of the data register is returned. This is independent of any other configuration (Figure 22-76). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 881 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.4.1.2 Input Register This is a read-only register and always returns the buffered state of the pin (Figure 22-76). 22.4.1.3 Data Direction Register This register defines whether the pin is used as an input or an output. If a peripheral module controls the pin the contents of the data direction register is ignored (Figure 22-76). PTI 0 1 PT 0 PIN 1 DDR 0 1 data out Module output enable module enable Figure 22-76. Illustration of I/O Pin Functionality 22.4.1.4 Reduced Drive Register If the pin is used as an output this register allows the configuration of the drive strength. 22.4.1.5 Pull Device Enable Register This register turns on a pull-up or pull-down device. It becomes active only if the pin is used as an input or as a wired-OR output. 22.4.1.6 Polarity Select Register This register selects either a pull-up or pull-down device if enabled. It becomes active only if the pin is used as an input. A pull-up device can be activated if the pin is used as a wired-OR output. If the pin is used as an interrupt input this register selects the active interrupt edge. 22.4.1.7 Wired-OR Mode Register If the pin is used as an output this register turns off the active high drive. This allows wired-OR type connections of outputs. MC9S12XDP512 Data Sheet, Rev. 2.21 882 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.4.1.8 Interrupt Enable Register If the pin is used as an interrupt input this register serves as a mask to the interrupt flag to enable/disable the interrupt. 22.4.1.9 Interrupt Flag Register If the pin is used as an interrupt input this register holds the interrupt flag after a valid pin event. 22.4.1.10 Module Routing Register This register supports the re-routing of the CAN0, CAN4, SPI0, SPI1, and SPI2 pins to alternative ports. This allows a software re-configuration of the pinouts of the different package options with respect to above peripherals. NOTE The purpose of the module routing register is to provide maximum flexibility for derivatives with a lower number of MSCAN and SPI modules. Table 22-68. Module Implementations on Derivatives 22.4.2 22.4.2.1 MSCAN Modules SPI Modules Number of Modules CAN0 CAN1 CAN2 CAN3 CAN4 SPI0 SPI1 SPI2 5 yes yes yes yes yes -- -- -- 4 yes yes yes -- yes -- -- -- 3 yes yes -- -- yes yes yes yes 2 yes -- -- -- yes yes yes -- 1 yes -- -- -- -- yes -- -- Ports BKGD Pin The BKGD pin is associated with the S12X_BDM and S12X_EBI modules. During reset, the BKGD pin is used as MODC input. 22.4.2.2 Port A and B Port A pins PA[7:0] and Port B pins PB[7:0] can be used for either general-purpose I/O, or, in 144-pin packages, also with the external bus interface. In this case port A and port B are associated with the external address bus outputs ADDR15-ADDR8 and ADDR7-ADDR0, respectively. PB0 is the ADDR0 or UDS output. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 883 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.4.2.3 Port C and D Port C pins PC[7:0] and port D pins PD[7:0] can be used for either general-purpose I/O, or, in 144-pin packages, also with the external bus interface. In this case port C and port D are associated with the external data bus inputs/outputs DATA15-DATA8 and DATA7-DATA0, respectively. These pins are configured for reduced input threshold in certain operating modes (refer to S12X_EBI section). NOTE Port C and D are neither available in 112-pin nor in 80-pin packages. 22.4.2.4 Port E Port E is associated with the external bus control outputs R/W, LSTRB, LDS and RE, the free-running clock outputs ECLK and ECLK2X, as well as with the TAGHI, TAGLO, MODA and MODB and interrupt inputs IRQ and XIRQ. Port E pins PE[7:2] can be used for either general-purpose I/O or with the alternative functions. Port E pin PE[7] an be used for either general-purpose I/O or as the free-running clock ECLKX2 output running at the core clock rate. The clock output is always enabled in emulation modes. Port E pin PE[4] an be used for either general-purpose I/O or as the free-running clock ECLK output running at the bus clock rate or at the programmed divided clock rate. The clock output is always enabled in emulation modes. Port E pin PE[1] can be used for either general-purpose input or as the level- or falling edge-sensitive IRQ interrupt input. IRQ will be enabled by setting the IRQEN configuration bit (Section 22.3.2.14, "IRQ Control Register (IRQCR)") and clearing the I-bit in the CPU's condition code register. It is inhibited at reset so this pin is initially configured as a simple input with a pull-up. Port E pin PE[0] can be used for either general-purpose input or as the level-sensitive XIRQ interrupt input. XIRQ can be enabled by clearing the X-bit in the CPU's condition code register. It is inhibited at reset so this pin is initially configured as a high-impedance input with a pull-up. Port E pins PE[5] and PE[6] are configured for reduced input threshold in certain modes (refer to S12X_EBI section). 22.4.2.5 Port K Port K pins PK[7:0] can be used for either general-purpose I/O, or, in 144-pin packages, also with the external bus interface. In this case port K pins PK[6:0] are associated with the external address bus outputs ADDR22-ADDR16 and PK7 is associated to the EWAIT input. Port K pin PE[7] is configured for reduced input threshold in certain modes (refer to S12X_EBI section). NOTE Port K is not available in 80-pin packages. PK[6] is not available in 112-pin packages. MC9S12XDP512 Data Sheet, Rev. 2.21 884 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.4.2.6 Port T This port is associated with the ECT module. Port T pins PT[7:0] can be used for either general-purpose I/O, or with the channels of the enhanced capture timer. 22.4.2.7 Port S This port is associated with SCI0, SCI1 and SPI0. Port S pins PS[7:0] can be used either for generalpurpose I/O, or with the SCI and SPI subsystems. The SPI0 pins can be re-routed. Refer to Section 22.3.2.37, "Module Routing Register (MODRR)". NOTE PS[7:4] are not available in 80-pin packages. 22.4.2.8 Port M This port is associated with the SCI3, CAN4-0 and SPI0. Port M pins PM[7:0] can be used for either general purpose I/O, or with the CAN, SCI and SPI subsystems. The CAN0, CAN4 and SPI0 pins can be re-routed. Refer to Section 22.3.2.37, "Module Routing Register (MODRR)". NOTE PM[7:6] are not available in 80-pin packages. 22.4.2.9 Port P This port is associated with the PWM, SPI1 and SPI2. Port P pins PP[7:0] can be used for either general purpose I/O, or with the PWM and SPI subsystems. The pins are shared between the PWM channels and the SPI1 and SPI2 modules. If the PWM is enabled the pins become PWM output channels with the exception of pin 7 which can be PWM input or output. If SPI1 or SPI2 are enabled and PWM is disabled, the respective pin configuration is determined by status bits in the SPI modules. The SPI1 and SPI2 pins can be re-routed. Refer to Section 22.3.2.37, "Module Routing Register (MODRR)". Port P offers 8 I/O pins with edge triggered interrupt capability in wired-OR fashion (Section 22.4.3, "Pin Interrupts"). NOTE PP[6] is not available in 80-pin packages. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 885 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.4.2.10 Port H This port is associated with the SPI1, SPI2, SCI4, and SCI5. Port H pins PH[7:0] can be used for either general purpose I/O, or with the SPI and SCI subsystems. Port H pins can be used with the routed SPI1 and SPI2 modules. Refer to Section 22.3.2.37, "Module Routing Register (MODRR)". Port H offers 8 I/O pins with edge triggered interrupt capability (Section 22.4.3, "Pin Interrupts"). NOTE Port H is not available in 80-pin packages. 22.4.2.11 Port J This port is associated with the chip selects CS0, CS1, CS2 and CS3 as well as with CAN4, CAN0, IIC1, IIC0, and SCI2. Port J pins PJ[7:4] and PJ[2:0] can be used for either general purpose I/O, or with the CAN, IIC, or SCI subsystems. If IIC takes precedence the associated pins become IIC open-drain output pins. The CAN4 pins can be re-routed. Refer to Section 22.3.2.37, "Module Routing Register (MODRR)". Port J pins can be used with the routed CAN0 modules. Refer to Section 22.3.2.37, "Module Routing Register (MODRR)". Port J offers 7 I/O pins with edge triggered interrupt capability (Section 22.4.3, "Pin Interrupts"). NOTE PJ[5,4,2] are not available in 112-pin packages. PJ[5,4,2,1,0] are not available in 80-pin packages. 22.4.2.12 Port AD0 This port is associated with the ATD0. Port AD0 pins PAD07-PAD00 can be used for either general purpose I/O, or with the ATD0 subsystem. 22.4.2.13 Port AD1 This port is associated with the ATD1. Port AD1 pins PAD23-PAD08 can be used for either general purpose I/O, or with the ATD1 subsystem. NOTE PAD[23:16] are not available in 112-pin packages. PAD[23:08] are not available in 80-pin packages. MC9S12XDP512 Data Sheet, Rev. 2.21 886 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) 22.4.3 Pin Interrupts Ports P, H and J offer pin interrupt capability. The interrupt enable as well as the sensitivity to rising or falling edges can be individually configured on per-pin basis. All bits/pins in a port share the same interrupt vector. Interrupts can be used with the pins configured as inputs or outputs. An interrupt is generated when a bit in the port interrupt flag register and its corresponding port interrupt enable bit are both set. The pin interrupt feature is also capable to wake up the CPU when it is in STOP or WAIT mode. A digital filter on each pin prevents pulses (Figure 22-78) shorter than a specified time from generating an interrupt. The minimum time varies over process conditions, temperature and voltage (Figure 22-77 and Table 22-69). Glitch, filtered out, no interrupt flag set Valid pulse, interrupt flag set uncertain tpign tpval Figure 22-77. Interrupt Glitch Filter on Port P, H, and J (PPS = 0) Table 22-69. Pulse Detection Criteria Mode Pulse 1 STOP Unit STOP1 Ignored tpulse 3 Bus clocks tpulse tpign Uncertain 3 < tpulse < 4 Bus clocks tpign < tpulse < tpval Valid tpulse 4 Bus clocks tpulse tpval These values include the spread of the oscillator frequency over temperature, voltage and process. tpulse Figure 22-78. Pulse Illustration MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 887 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) A valid edge on an input is detected if 4 consecutive samples of a passive level are followed by 4 consecutive samples of an active level directly or indirectly. The filters are continuously clocked by the bus clock in run and wait mode. In stop mode, the clock is generated by an RC-oscillator in the port integration module. To maximize current saving the RC oscillator runs only if the following condition is true on any pin individually: Sample count <= 4 and interrupt enabled (PIE = 1) and interrupt flag not set (PIF = 0). 22.4.4 Expanded Bus Pin Functions All peripheral ports T, S, M, P, H, J, AD0, and AD1 start up as general purpose inputs after reset. Depending on the external mode pin condition, the external bus interface related ports A, B, C, D, E, and K start up as general purpose inputs on reset or are configured for their alternate functions. Table 22-70 lists the pin functions in relationship with the different operating modes. If two entries per pin are displayed, a `mux' indicates time-multiplexing between the two functions and an `or' means that a configuration bit exists which can be altered after reset to select the respective function (displayed in italics). Refer to S12X_EBI section for details. Table 22-70. Expanded Bus Pin Functions versus Operating Modes Single-Chip Modes Expanded Modes Pin Normal Single-Chip Special Single-Chip Normal Expanded Emulation Single-Chip Emulation Expanded Special Test PK7 GPIO GPIO GPIO or EWAIT GPIO GPIO or EWAIT GPIO PK[6:4] GPIO GPIO ADDR[22:20] or GPIO ADDR[22:20] mux ACC[2:0] ADDR[22:20] mux ACC[2:0] ADDR[22:20] PK[3:0] GPIO GPIO ADDR[19:16] or GPIO ADDR[19:16] mux IQSTAT[3:0] ADDR[19:16] mux IQSTAT[3:0] ADDR[19:16] PA[7:0] GPIO GPIO ADDR[15:8] or GPIO ADDR[15:8] mux IVD[15:8] ADDR[15:8] mux IVD[15:8] ADDR[15:8] PB[7:1] GPIO GPIO ADDR[7:1] or GPIO ADDR[7:1] mux IVD[7:1] ADDR[7:1] mux IVD[7:1] ADDR[7:1] PB0 GPIO GPIO UDS or GPIO ADDR0 mux IVD0 ADDR0 mux IVD0 ADDR0 PC[7:0] GPIO GPIO DATA[15:8] or GPIO DATA[15:8] DATA[15:8] DATA[15:8] or GPIO PD[7:0] GPIO GPIO DATA[7:0] DATA[7:0] DATA[7:0] DATA[7:0] PE7 GPIO or ECLKX2 GPIO or ECLKX2 GPIO or ECLKX2 ECLKX2 ECLKX2 GPIO or ECLKX2 MC9S12XDP512 Data Sheet, Rev. 2.21 888 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) Table 22-70. Expanded Bus Pin Functions versus Operating Modes (continued) Single-Chip Modes 1 Expanded Modes Pin Normal Single-Chip Special Single-Chip Normal Expanded Emulation Single-Chip Emulation Expanded Special Test PE6 GPIO GPIO GPIO TAGHI TAGHI GPIO PE5 GPIO GPIO RE TAGLO TAGLO GPIO PE4 GPIO or ECLK ECLK or GPIO ECLK or GPIO ECLK ECLK ECLK or GPIO PE3 GPIO GPIO LDS or GPIO LSTRB LSTRB LSTRB PE2 GPIO GPIO WE R/W R/W R/W PJ5 GPIO GPIO GPIO or CS2 GPIO GPIO or CS2 GPIO or CS2 PJ4 GPIO GPIO GPIO or CS0 (1) GPIO GPIO or CS0 (1) GPIO or CS0 PJ2 GPIO GPIO GPIO or CS1 GPIO GPIO or CS1 GPIO or CS1 PJ0 GPIO GPIO GPIO or CS3 GPIO GPIO or CS3 GPIO or CS3 Depending on ROMON bit. Refer to Device Guide, S12X_EBI section and S12X_MMC section for details. 22.4.5 Low-Power Options 22.4.5.1 Run Mode No low-power options exist for this module in run mode. 22.4.5.2 Wait Mode No low-power options exist for this module in wait mode. 22.4.5.3 Stop Mode All clocks are stopped. There are asynchronous paths to generate interrupts from stop on port P, H, and J. 22.5 * Initialization and Application Information It is not recommended to write PORTx and DDRx in a word access. When changing the register pins from inputs to outputs, the data may have extra transitions during the write access. Initialize the port data register before enabling the outputs. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 889 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) * Power consumption will increase the more the voltages on general purpose input pins deviate from the supply voltages towards mid-range because the digital input buffers operate in the linear region. MC9S12XDP512 Data Sheet, Rev. 2.21 890 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 891 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 892 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 893 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 894 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 895 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 896 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 897 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 898 Freescale Semiconductor Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 899 Chapter 22 DP512 Port Integration Module (S12XDP512PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 900 Freescale Semiconductor Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Introduction The S12XD family port integration module (below referred to as PIM) establishes the interface between the peripheral modules including the non-multiplexed external bus interface module (S12X_EBI) and the I/O pins for all ports. It controls the electrical pin properties as well as the signal prioritization and multiplexing on shared pins. This document covers the description of: * Port A, B used as address output of the S12X_EBI and Port C, D used as data I/O of the S12X_EBI * Port E associated with the S12X_EBI control signals and the IRQ, XIRQ interrupt inputs * Port K associated with address output and control signals of the S12X_EBI * Port T connected to the Enhanced Capture Timer (ECT) module * Port S associated with 2 SCI and 1 SPI modules * Port M associated with 3 MSCAN modules * Port P connected to the PWM and 2 SPI modules -- inputs can be used as an external interrupt source * Port H associated with 1 SCI module -- inputs can be used as an external interrupt source * Port J associated with 1 MSCAN, 1 SCI, and 1 IIC module -- inputs can be used as an external interrupt source * Port AD0 and AD1 associated with one 8-channel andone 16-channel ATD module Most I/O pins can be configured by register bits to select data direction and drive strength, to enable and select pull-up or pull-down devices. Interrupts can be enabled on specific pins resulting in status flags. The I/O's of 2 MSCAN and 3 SPI modules can be routed from their default location to alternative port pins. NOTE The implementation of the PIM is device dependent. Therefore some functions are not available on certain derivatives or 112-pin and 80-pin package options. 23.0.1 Features A full-featured PIM module includes these distinctive registers: * Data and data direction registers for Ports A, B, C, D, E, K, T, S, M, P, H, J, AD0, and AD1 when used as general-purpose I/O MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 901 Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) * * * * * * * * * * Control registers to enable/disable pull-device and select pull-ups/pull-downs on Ports T, S, M, P, H, and J on per-pin basis Control registers to enable/disable pull-up devices on Ports AD0, and AD1 on per-pin basis Single control register to enable/disable pull-ups on Ports A, B, C, D, E, and K on per-port basis and on BKGD pin Control registers to enable/disable reduced output drive on Ports T, S, M, P, H, J, AD0, and AD1 on per-pin basis Single control register to enable/disable reduced output drive on Ports A, B, C, D, E, and K on perport basis Control registers to enable/disable open-drain (wired-OR) mode on Ports S and M Control registers to enable/disable pin interrupts on Ports P, H, and J Interrupt flag register for pin interrupts on Ports P, H, and J Control register to configure IRQ pin operation Free-running clock outputs A standard port pin has the following minimum features: * Input/output selection * 5V output drive with two selectable drive strengths * 5V digital and analog input * Input with selectable pull-up or pull-down device Optional features: * Open drain for wired-OR connections * Interrupt inputs with glitch filtering * Reduced input threshold to support low voltage applications 23.0.2 Block Diagram Figure 23-1 is a block diagram of the PIM. * Signals shown in Bold are not available in 80-pin packages. * Signals shown in Bold-Italics are neither available in 112-pin nor in 80-pin packages. * Shaded labels denote alternative module routing ports. MC9S12XDP512 Data Sheet, Rev. 2.21 902 Freescale Semiconductor DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 Port D DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 Port AD1 Port AD0 Port T PP7 PP6 PP5 PP4 PP3 PP2 PP1 PP0 PS7 PS6 PS5 PS4 PS3 PS2 PS1 PS0 SS SPI0 SCK MOSI MISO TXD SCI1 RXD TXD SCI0 RXD BKGD/MODC ECLKX2/XCLKS TAGHI/MODB TAGLO/RE/MODA ECLK S12X_EBI LDS/LSTRB S12X_BDM WE/R/W S12X_DBG IRQ XIRQ S12X_INT EWAIT/ROMCTL NOACC/ADDR22 ADDR21 ADRR20 ADDR19 ADDR18 ADDR17 ADDR16 Figure 23-1. PIMXDQ256 Block Diagram Port E ADDR7 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0/UDS SCK SS MOSI MISO SS SPI1 SCK MOSI MISO SPI2 Port K ADDR15 ADDR14 ADDR13 ADDR12 ADDR11 ADDR10 ADDR9 ADDR8 PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 PT7 PT6 PT5 PT4 PT3 PT2 PT1 PT0 Port P TXCAN CAN2 RXCAN TXCAN CAN1 RXCAN TXCAN CAN0 RXCAN PAD22 PAD20 PAD18 PAD16 PAD14 PAD12 PAD10 PAD08 PAD07 PAD06 PAD05 PAD04 PAD03 PAD02 PAD01 PAD00 Port S ATD1 IOC7 IOC6 IOC5 IOC4 IOC3 IOC2 IOC1 IOC0 Interrupt Logic SPI0 CAN0 CAN0 CAN4 CAN4 AN7 AN6 AN5 AN4 AN3 AN2 AN1 AN0 SCI2 PWM Interrupt Logic TXCAN CAN4 RXCAN SCL IIC0 SDA TXD RXD AN15,14 AN13,12 AN11,10 AN9,8 AN7,6 AN5,4 AN3,2 AN1,0 ATD0 TXD SCI4 RXD Port C PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 Port B PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 Port A PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 Port M PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 Port J PM7 PM6 PM5 PM4 PM3 PM2 PM1 PM0 Interrupt Logic CAN0 PJ6 PJ5 PJ4 PJ2 PJ1 PJ0 SPI1 PJ7 SPI2 Port H PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 ECT Port Integration Module BKGD PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 PK7 PK6 PK5 PK4 PK3 PK2 PK1 PK0 PAD23 PAD21 PAD19 PAD17 PAD15 PAD13 PAD11 PAD09 Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) External Signal Description This section lists and describes the signals that do connect off-chip. 23.0.3 Signal Properties Table 23-1 shows all the pins and their functions that are controlled by the PIM. Refer to Section , "Functional Description" for the availability of the individual pins in the different package options. NOTE If there is more than one function associated with a pin, the priority is indicated by the position in the table from top (highest priority) to bottom (lowest priority). Table 23-1. Pin Functions and Priorities (Sheet 1 of 7) Port Pin Name Pin Function and Priority I/O -- BKGD MODC1 I BKGD I/O S12X_BDM communication pin ADDR[15:8] mux IVD[15:8]2 O High-order external bus address output (multiplexed with IVIS data) GPIO I/O General-purpose I/O ADDR[7:1] mux IVD[7:1]2 O Low-order external bus address output (multiplexed with IVIS data) GPIO I/O General-purpose I/O ADDR[0] mux IVD02 O Low-order external bus address output (multiplexed with IVIS data) UDS O Upper data strobe GPIO I/O General-purpose I/O DATA[15:8] I/O High-order bidirectional data input/output Configurable for reduced input threshold GPIO I/O General-purpose I/O DATA[7:0] I/O Low-order bidirectional data input/output Configurable for reduced input threshold GPIO I/O General-purpose I/O A B PA[7:0] PB[7:1] PB[0] C D PC[7:0] PD[7:0] Description MODC input during RESET Pin Function after Reset BKGD Mode dependent3 Mode dependent3 Mode dependent3 Mode dependent3 MC9S12XDP512 Data Sheet, Rev. 2.21 904 Freescale Semiconductor Table 23-1. Pin Functions and Priorities (Sheet 2 of 7) Port Pin Name PE[7] PE[6] Pin Function and Priority I/O XCLKS1 I External clock selection input during RESET ECLKX2 I Free-running clock output at Core Clock rate (ECLK x 2) GPIO I/O MODB1 I MODB input during RESET TAGHI I Instruction tagging low pin Configurable for reduced input threshold GPIO I/O MODA1 I MODA input during RESET RE O Read enable signal TAGLO I Instruction tagging low pin Configurable for reduced input threshold GPIO I/O General-purpose I/O ECLK O Free-running clock output at the Bus Clock rate or programmable divided in normal modes GPIO I/O General-purpose I/O EROMCTL1 I EROMON bit control input during RESET LSTRB O Low strobe bar output LDS O Lower data strobe GPIO I/O General-purpose I/O R/W O Read/write output for external bus WE O Write enable signal GPIO I/O General-purpose I/O IRQ I GPIO I/O XIRQ I GPIO I/O PE[5] E PE[4] PE[3] PE[2] Description Pin Function after Reset General-purpose I/O General-purpose I/O Maskable level- or falling edge-sensitive interrupt input PE[1] General-purpose I/O Non-maskable level-sensitive interrupt input PE[0] General-purpose I/O Mode dependent3 Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-1. Pin Functions and Priorities (Sheet 3 of 7) Port Pin Name PK[7] K PK[6:4] PK[3:0] T Pin Function and Priority I/O Pin Function after Reset ROMCTL1 I ROMON bit control input during RESET EWAIT I External Wait signal Configurable for reduced input threshold GPIO I/O General-purpose I/O ADDR[22:20] mux ACC[2:0]2 O Extended external bus address output (multiplexed with access master output) GPIO I/O General-purpose I/O ADDR[19:16] mux IQSTAT[3:0]2 O Extended external bus address output (multiplexed with instruction pipe status bits) GPIO I/O General-purpose I/O IOC[7:0] I/O Enhanced Capture Timer Channels 7-0 input/output GPIO I/O General-purpose I/O SS0 I/O Serial Peripheral Interface 0 slave select output in master mode, input in slave mode or master mode. GPIO I/O General-purpose I/O SCK0 I/O Serial Peripheral Interface 0 serial clock pin GPIO I/O General-purpose I/O MOSI0 I/O Serial Peripheral Interface 0 master out/slave in pin GPIO I/O General-purpose I/O MISO0 I/O Serial Peripheral Interface 0 master in/slave out pin GPIO I/O General-purpose I/O TXD1 O Serial Communication Interface 1 transmit pin GPIO I/O General-purpose I/O RXD1 I GPIO I/O General-purpose I/O TXD0 O Serial Communication Interface 0 transmit pin GPIO I/O General-purpose I/O RXD0 I GPIO I/O Description Mode dependent3 PT[7:0] GPIO PS7 PS6 PS5 PS4 S GPIO PS3 Serial Communication Interface 1 receive pin PS2 PS1 Serial Communication Interface 0 receive pin PS0 General-purpose I/O MC9S12XDP512 Data Sheet, Rev. 2.21 906 Freescale Semiconductor Table 23-1. Pin Functions and Priorities (Sheet 4 of 7) Port Pin Name Pin Function and Priority I/O TXCAN4 O MSCAN4 transmit pin GPIO I/O General-purpose I/O RXCAN4 I MSCAN4 receive pin GPIO I/O General-purpose I/O TXCAN2 O MSCAN2 transmit pin TXCAN0 O MSCAN0 transmit pin TXCAN4 O MSCAN4 transmit pin SCK0 I/O Serial Peripheral Interface 0 serial clock pin If CAN0 is routed to PM[3:2] the SPI0 can still be used in bidirectional master mode. GPIO I/O General-purpose I/O RXCAN2 I MSCAN2 receive pin RXCAN0 I MSCAN0 receive pin RXCAN4 I MSCAN4 receive pin MOSI0 I/O Serial Peripheral Interface 0 master out/slave in pin If CAN0 is routed to PM[3:2] the SPI0 can still be used in bidirectional master mode. GPIO I/O General-purpose I/O TXCAN1 O MSCAN1 transmit pin TXCAN0 O MSCAN0 transmit pin SS0 I/O Serial Peripheral Interface 0 slave select output in master mode, input for slave mode or master mode. GPIO I/O General-purpose I/O RXCAN1 I MSCAN1 receive pin RXCAN0 I MSCAN0 receive pin MISO0 I/O Serial Peripheral Interface 0 master in/slave out pin GPIO I/O General-purpose I/O TXCAN0 O MSCAN0 transmit pin GPIO I/O General-purpose I/O RXCAN0 I MSCAN0 receive pin GPIO I/O General-purpose I/O Description Pin Function after Reset PM7 PM6 PM5 PM4 M PM3 PM2 PM1 PM0 GPIO Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-1. Pin Functions and Priorities (Sheet 5 of 7) Port Pin Name PP7 PP6 PP5 PP4 Pin Function and Priority I/O Pin Function after Reset PWM7 I/O Pulse Width Modulator input/output channel 7 SCK2 I/O Serial Peripheral Interface 2 serial clock pin GPIO/KWP7 I/O General-purpose I/O with interrupt PWM6 O Pulse Width Modulator output channel 6 SS2 I/O Serial Peripheral Interface 2 slave select output in master mode, input for slave mode or master mode. GPIO/KWP6 I/O General-purpose I/O with interrupt PWM5 O Pulse Width Modulator output channel 5 MOSI2 I/O Serial Peripheral Interface 2 master out/slave in pin GPIO/KWP5 I/O General-purpose I/O with interrupt PWM4 O Pulse Width Modulator output channel 4 MISO2 I/O Serial Peripheral Interface 2 master in/slave out pin GPIO/KWP4 I/O General-purpose I/O with interrupt PWM3 O Pulse Width Modulator output channel 3 SS1 I/O Serial Peripheral Interface 1 slave select output in master mode, input for slave mode or master mode. GPIO/KWP3 I/O General-purpose I/O with interrupt PWM2 O Pulse Width Modulator output channel 2 SCK1 I/O Serial Peripheral Interface 1 serial clock pin GPIO/KWP2 I/O General-purpose I/O with interrupt PWM1 O Pulse Width Modulator output channel 1 MOSI1 I/O Serial Peripheral Interface 1 master out/slave in pin GPIO/KWP1 I/O General-purpose I/O with interrupt PWM0 O Pulse Width Modulator output channel 0 MISO1 I/O Serial Peripheral Interface 1 master in/slave out pin GPIO/KWP0 I/O General-purpose I/O with interrupt Description P GPIO PP3 PP2 PP1 PP0 MC9S12XDP512 Data Sheet, Rev. 2.21 908 Freescale Semiconductor Table 23-1. Pin Functions and Priorities (Sheet 6 of 7) Port Pin Name Pin Function and Priority I/O SS2 I/O Serial Peripheral Interface 2 slave select output in master mode, input for slave mode or master mode GPIO/KWH7 I/O General-purpose I/O with interrupt SCK2 I/O Serial Peripheral Interface 2 serial clock pin GPIO/KWH6 I/O General-purpose I/O with interrupt MOSI2 I/O Serial Peripheral Interface 2 master out/slave in pin TXD4 O Serial Communication Interface 4 transmit pin GPIO/KWH5 I/O General-purpose I/O with interrupt MISO2 I/O Serial Peripheral Interface 2 master in/slave out pin RXD4 I GPIO/KWH4 I/O General-purpose I/O with interrupt SS1 I/O Serial Peripheral Interface 1 slave select output in master mode, input for slave mode or master mode. GPIO/KWH3 I/O General-purpose I/O with interrupt SCK1 I/O Serial Peripheral Interface 1 serial clock pin GPIO/KWH2 I/O General-purpose I/O with interrupt MOSI1 I/O Serial Peripheral Interface 1 master out/slave in pin GPIO/KWH1 I/O General-purpose I/O with interrupt MISO1 I/O Serial Peripheral Interface 1 master in/slave out pin GPIO/KWH0 I/O General-purpose I/O with interrupt PH7 Description Pin Function after Reset PH6 PH5 PH4 Serial Communication Interface 4 receive pin H GPIO PH3 PH2 PH1 PH0 Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-1. Pin Functions and Priorities (Sheet 7 of 7) Port Pin Name Pin Function and Priority I/O TXCAN4 O MSCAN4 transmit pin SCL0 O Inter Integrated Circuit 0 serial clock line TXCAN0 O MSCAN0 transmit pin GPIO/KWJ7 I/O General-purpose I/O with interrupt RXCAN4 I SDA0 I/O RXCAN0 I GPIO/KWJ6 I/O General-purpose I/O with interrupt CS2 O Chip select 2 GPIO/KWJ7 I/O General-purpose I/O with interrupt CS0 O Chip select 0 GPIO/KWJ6 I/O General-purpose I/O with interrupt CS1 O Chip select 1 GPIO/KWJ2 I/O General-purpose I/O with interrupt TXD2 O Serial Communication Interface 2 transmit pin GPIO/KWJ1 I/O General-purpose I/O with interrupt RXD2 I Serial Communication Interface 2 receive pin CS3 O Chip select 3 GPIO/KWJ0 I/O General-purpose I/O with interrupt GPIO I/O General-purpose I/O AN[7:0] I ATD0 analog inputs GPIO I/O General-purpose I/O AN[15:0] I ATD1 analog inputs Description Pin Function after Reset PJ7 MSCAN4 receive pin Inter Integrated Circuit 0 serial data line PJ6 MSCAN0 receive pin PJ5 J GPIO PJ4 PJ2 PJ1 PJ0 AD0 AD1 PAD[07:00] GPIO PAD[23:08] GPIO 1. Function active when RESET asserted. 2. Only available in emulation modes or in Special Test Mode with IVIS on. 3. Refer also to Table 23-70 and S12X_EBI section. Memory Map and Register Definition This section provides a detailed description of all PIMregisters. 23.0.4 Module Memory Map Table 23-2 shows the register map of the port integration module. MC9S12XDP512 Data Sheet, Rev. 2.21 910 Freescale Semiconductor Table 23-2. PIM Memory Map (Sheet 1 of 3) Address Use Access 0x0000 Port A Data Register (PORTA) Read / Write 0x0001 Port B Data Register (PORTB) Read / Write 0x0002 Port A Data Direction Register (DDRA) Read / Write 0x0003 Port B Data Direction Register (DDRB) Read / Write 0x0004 Port C Data Register (PORTC) Read / Write 0x0005 Port D Data Register (PORTD) Read / Write 0x0006 Port C Data Direction Register (DDRC) Read / Write 0x0007 Port D Data Direction Register (DDRD) Read / Write 0x0008 Port E Data Register (PORTE) Read / Write1 0x0009 Port E Data Direction Register (DDRE) Read / Write1 0x000A : 0x000B Non-PIM Address Range 0x000C Pull-up Up Control Register (PUCR) Read / Write1 0x000D Reduced Drive Register (RDRIV) Read / Write1 0x000E : 0x001B Non-PIM Address Range 0x001C ECLK Control Register (ECLKCTL) 0x001D PIM Reserved 0x001E IRQ Control Register (IRQCR) 0x001F PIM Reserved -- 0x0020 : 0x0031 Non-PIM Address Range -- 0x0032 Port K Data Register (PORTK) Read / Write 0x0033 Port K Data Direction Register (DDRK) Read / Write 0x0034 : 0x023F Non-PIM Address Range 0x0240 Port T Data Register (PTT) Read / Write 0x0241 Port T Input Register (PTIT) Read 0x0242 Port T Data Direction Register (DDRT) Read / Write 0x0243 Port T Reduced Drive Register (RDRT) Read / Write 0x0244 Port T Pull Device Enable Register (PERT) Read / Write 0x0245 Port T Polarity Select Register (PPST) Read / Write 0x0246 PIM Reserved -- 0x0247 PIM Reserved -- -- -- Read / Write1 -- Read / Write1 -- Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-2. PIM Memory Map (Sheet 2 of 3) Address Use Access 0x0248 Port S Data Register (PTS) Read / Write 0x0249 Port S Input Register (PTIS) Read 0x024A Port S Data Direction Register (DDRS) Read / Write 0x024B Port S Reduced Drive Register (RDRS) Read / Write 0x024C Port S Pull Device Enable Register (PERS) Read / Write 0x024D Port S Polarity Select Register (PPSS) Read / Write 0x024E Port S Wired-OR Mode Register (WOMS) Read / Write 0x024F PIM Reserved 0x0250 Port M Data Register (PTM) Read / Write 0x0251 Port M Input Register (PTIM) Read 0x0252 Port M Data Direction Register (DDRM) Read / Write 0x0253 Port M Reduced Drive Register (RDRM) Read / Write 0x0254 Port M Pull Device Enable Register (PERM) Read / Write 0x0255 Port M Polarity Select Register (PPSM) Read / Write 0x0256 Port M Wired-OR Mode Register (WOMM) Read / Write 0x0257 Module Routing Register (MODRR) Read / Write 0x0258 Port P Data Register (PTP) Read / Write 0x0259 Port P Input Register (PTIP) Read 0x025A Port P Data Direction Register (DDRP) Read / Write 0x025B Port P Reduced Drive Register (RDRP) Read / Write 0x025C Port P Pull Device Enable Register (PERP) Read / Write 0x025D Port P Polarity Select Register (PPSP) Read / Write 0x025E Port P Interrupt Enable Register (PIEP) Read / Write 0x025F Port P Interrupt Flag Register (PIFP) Read / Write 0x0260 Port H Data Register (PTH) Read / Write 0x0261 Port H Input Register (PTIH) Read 0x0262 Port H Data Direction Register (DDRH) Read / Write 0x0263 Port H Reduced Drive Register (RDRH) Read / Write 0x0264 Port H Pull Device Enable Register (PERH) Read / Write 0x0265 Port H Polarity Select Register (PPSH) Read / Write 0x0266 Port H Interrupt Enable Register (PIEH) Read / Write 0x0267 Port H Interrupt Flag Register (PIFH) Read / Write 0x0268 Port J Data Register (PTJ) Read / Write1 0x0269 Port J Input Register (PTIJ) Read 0x026A Port J Data Direction Register (DDRJ) -- Read / Write1 MC9S12XDP512 Data Sheet, Rev. 2.21 912 Freescale Semiconductor Table 23-2. PIM Memory Map (Sheet 3 of 3) Address Use Access 0x026B Port J Reduced Drive Register (RDRJ) Read / Write1 0x026C Port J Pull Device Enable Register (PERJ) Read / Write1 0x026D Port J Polarity Select Register (PPSJ) Read / Write1 0x026E Port J Interrupt Enable Register (PIEJ) Read / Write1 0x026F Port J Interrupt Flag Register (PIFJ) Read / Write1 0x0270 PIM Reserved 0x0271 Port AD0 Data Register 1 (PT1AD0) 0x0272 PIM Reserved 0x0273 Port AD0 Data Direction Register 1 (DDR1AD0) 0x0274 PIM Reserved 0x0275 Port AD0 Reduced Drive Register 1 (RDR1AD0) 0x0276 PIM Reserved 0x0277 Port AD0 Pull Up Enable Register 1 (PER1AD0) Read / Write 0x0278 Port AD1 Data Register 0 (PT0AD1) Read / Write 0x0279 Port AD1 Data Register 1 (PT1AD1) Read / Write 0x027A Port AD1 Data Direction Register 0 (DDR0AD1) Read / Write 0x027B Port AD1 Data Direction Register 1 (DDR1AD1) Read / Write 0x027C Port AD1 Reduced Drive Register 0 (RDR0AD1) Read / Write 0x027D Port AD1 Reduced Drive Register 1 (RDR1AD1) Read / Write 0x027E Port AD1 Pull Up Enable Register 0 (PER0AD1) Read / Write 0x027F Port AD1 Pull Up Enable Register 1 (PER1AD1) Read / Write -- Read / Write -- Read / Write -- Read / Write -- 1. Write access not applicable for one or more register bits. Refer to Section 23.0.5, "Register Descriptions". 23.0.5 Register Descriptions Table 23-3 summarizes the effect on the various configuration bits, data direction (DDR), output level (IO), reduced drive (RDR), pull enable (PE), pull select (PS), and interrupt enable (IE) for the ports. The configuration bit PS is used for two purposes: 1. Configure the sensitive interrupt edge (rising or falling), if interrupt is enabled. 2. Select either a pull-up or pull-down device if PE is active. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-3. Pin Configuration Summary DDR IO RDR PE PS1 IE2 0 x x 0 x 0 Input Disabled Disabled 0 x x 1 0 0 Input Pull Up Disabled 0 x x 1 1 0 Input Pull Down Disabled 0 x x 0 0 1 Input Disabled Falling edge 0 x x 0 1 1 Input Disabled Rising edge 0 x x 1 0 1 Input Pull Up Falling edge 0 x x 1 1 1 Input Pull Down Rising edge 1 0 0 x x 0 Output, full drive to 0 Disabled Disabled 1 1 0 x x 0 Output, full drive to 1 Disabled Disabled 1 0 1 x x 0 Output, reduced drive to 0 Disabled Disabled 1 1 1 x x 0 Output, reduced drive to 1 Disabled Disabled 1 0 0 x 0 1 Output, full drive to 0 Disabled Falling edge 1 1 0 x 1 1 Output, full drive to 1 Disabled Rising edge 1 0 1 x 0 1 Output, reduced drive to 0 Disabled Falling edge 1 1 1 x 1 1 Output, reduced drive to 1 Disabled Rising edge Function Pull Device Interrupt 1. Always "0" on Port A, B, C, D, E, K, AD0, and AD1. 2. Applicable only on Port P, H, and J. NOTE All register bits in this module are completely synchronous to internal clocks during a register read. Register Name PORTA R W PORTB R W DDRA R W DDRB R W Bit 7 6 5 4 3 2 1 Bit 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 = Unimplemented or Reserved Figure 23-2. PIM Register Summary (Sheet 1 of 7) MC9S12XDP512 Data Sheet, Rev. 2.21 914 Freescale Semiconductor Register Name PORTC R W PORTD R W DDRC R W DDRD R W PORTE R W DDRE R W Bit 7 6 5 4 3 2 1 Bit 0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 DDRC7 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 0 0 R Non-PIM W Address Range PUCR R W RDRIV R W Non-PIM Address Range PUPKE RDPK BKPUE 0 0 W Reserved R PUPDE PUPCE PUPBE PUPAE RDPE RDPD RDPC RDPB RDPA EDIV1 EDIV0 0 R Non-PIM W Address Range ECLKCTL R PUPEE Non-PIM Address Range NECLK NCLKX2 0 0 IRQE IRQEN 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W IRQCR R W Reserved R W = Unimplemented or Reserved Figure 23-2. PIM Register Summary (Sheet 2 of 7) Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Register Name Bit 7 6 5 Non-PIM R Address W Range PORTK R W DDRK R W R W PTIT R 3 2 1 Bit 0 Non-PIM Address Range PK7 PK6 PK5 PK4 PK3 PK2 PK1 PK0 DDRK7 DDRK6 DDRK5 DDRK4 DDRK3 DDRK2 DDRK1 DDRK0 Non-PIM R Address W Range PTT 4 Non-PIM Address Range PTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0 PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0 DDRT7 DDRT6 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0 RDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0 PERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0 PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0 W DDRT R W RDRT R W PERT R W PPST R W Reserved R W Reserved R W PTS R W PTIS R W = Unimplemented or Reserved Figure 23-2. PIM Register Summary (Sheet 3 of 7) MC9S12XDP512 Data Sheet, Rev. 2.21 916 Freescale Semiconductor Register Name DDRS R W RDRS R W PERS R W PPSS R W WOMS R W Reserved R Bit 7 6 5 4 3 2 1 Bit 0 DDRS7 DDRS6 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0 RDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0 PERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0 PPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0 WOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0 0 0 0 0 0 0 0 0 PTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0 PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0 DDRM7 DDRM6 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0 RDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0 PERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0 PPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0 WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 MODRR6 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0 W PTM R W PTIM R W DDRM R W RDRM R W PERM R W PPSM R W WOMM R W MODRR R 0 W PTP R W PTP7 = Unimplemented or Reserved Figure 23-2. PIM Register Summary (Sheet 4 of 7) Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Register Name PTIP R Bit 7 6 5 4 3 2 1 Bit 0 PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0 DDRP7 DDRP6 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0 RDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0 PERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0 PPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSP0 PIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0 PIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0 PTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0 PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0 DDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 RDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0 PERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0 PPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0 PIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0 PIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0 W DDRP R W RDRP R W PERP R W PPSP R W PIEP R W PIFP R W PTH R W PTIH R W DDRH R W RDRH R W PERH R W PPSH R W PIEH R W PIFH R W = Unimplemented or Reserved Figure 23-2. PIM Register Summary (Sheet 5 of 7) MC9S12XDP512 Data Sheet, Rev. 2.21 918 Freescale Semiconductor Register Name PTJ R W PTIJ R Bit 7 6 5 4 PTJ7 PTJ6 PTJ5 PTJ4 PTIJ7 PTIJ6 PTIJ5 PTIJ4 DDRJ7 DDRJ6 DDRJ5 DDRJ4 RDRJ7 RDRJ6 RDRJ5 RDRJ4 PERJ7 PERJ6 PERJ5 PERJ4 PPSJ7 PPSJ6 PPSJ5 PPSJ4 PIEJ7 PIEJ6 PIEJ5 PIEJ4 PPSJ7 PPSJ6 PPSJ5 PPSJ4 0 0 0 0 PT1AD07 PT1AD06 PT1AD05 0 0 0 3 2 1 Bit 0 PTJ2 PTJ1 PTJ0 PTIJ2 PTIJ1 PTIJ0 DDRJ2 DDRJ1 DDRJ0 RDRJ2 RDRJ1 RDRJ0 PERJ2 PERJ1 PERJ0 PPSJ2 PPSJ1 PPSJ0 PIEJ2 PIEJ1 PIEJ0 PPSJ2 PPSJ1 PPSJ0 0 0 0 0 PT1AD04 PT1AD03 PT1AD02 PT1AD01 PT1AD00 0 0 0 0 0 0 0 W DDRJ R W RDRJ R W PERJ R W PPSJ R W PIEJ R W PIFJ R W Reserved R 0 0 0 0 0 0 W PT1AD0 R W Reserved R W DDR1AD0 R W Reserved R DDR1AD07 DDR1AD06 DDR1AD05 DDR1AD04 DDR1AD03 DDR1AD02 DDR1AD01 DDR1AD00 0 0 0 0 0 0 0 0 W RDR1AD0 R W Reserved R RDR1AD07 RDR1AD06 RDR1AD05 RDR1AD04 RDR1AD03 RDR1AD02 RDR1AD01 RDR1AD00 0 0 0 0 0 0 W = Unimplemented or Reserved Figure 23-2. PIM Register Summary (Sheet 6 of 7) 0 0 Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Register Name PER1AD0 R W PT0AD1 R W PT1AD1 R W DDR0AD1 R W DDR1AD1 R W RDR0AD1 R W RDR1AD1 R W PER0AD1 R W PER1AD1 R W Bit 7 6 5 4 3 2 1 Bit 0 PER1AD07 PER1AD06 PER1AD05 PER1AD04 PER1AD03 PER1AD02 PER1AD01 PER1AD00 PT0AD123 PT0AD122 PT0AD121 PT0AD120 PT0AD119 PT0AD118 PT0AD117 PT0AD116 PT1AD115 PT1AD114 PT1AD113 PT1AD112 PT1AD111 PT1AD110 PT1AD19 PT1AD18 DDR0AD123 DDR0AD122 DDR0AD121 DDR0AD120 DDR0AD119 DDR0AD118 DDR0AD117 DDR0AD116 DDR1AD115 DDR1AD114 DDR1AD113 DDR1AD112 DDR1AD111 DDR1AD110 DDR1AD19 DDR1AD18 RDR0AD123 RDR0AD122 RDR0AD121 RDR0AD120 RDR0AD119 RDR0AD118 RDR0AD117 RDR0AD116 RDR1AD115 RDR1AD114 RDR1AD113 RDR1AD112 RDR1AD111 RDR1AD110 RDR1AD19 RDR1AD18 PER0AD123 PER0AD122 PER0AD121 PER0AD120 PER0AD119 PER0AD118 PER0AD117 PER0AD116 PER1AD115 PER1AD114 PER1AD113 PER1AD112 PER1AD111 PER1AD110 PER1AD19 PER1AD18 = Unimplemented or Reserved 23.0.5.1 Port A DataFigure Register (PORTA) 23-2. PIM Register Summary (Sheet 7 of 7) 7 6 5 4 3 2 1 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 ADDR15 mux IVD15 ADDR14 mux IVD14 ADDR13 mux IVD13 ADDR12 mux IVD12 ADDR11 mux IVD11 ADDR10 mux IVD10 ADDR9 mux IVD9 ADDR8 mux IVD8 0 0 0 0 0 0 0 0 R W Alt. Function Reset Figure 23-3. Port A Data Register (PORTA) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. MC9S12XDP512 Data Sheet, Rev. 2.21 920 Freescale Semiconductor Table 23-4. PORTA Field Descriptions Field Description 7-0 PA[7:0] Port A -- Port A pins 7-0 are associated with address outputs ADDR15 through ADDR8 respectively inexpanded modesWhen this port is not used for external addresses, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 23.0.5.2 Port B Data Register (PORTB) 7 6 5 4 3 2 1 0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 0 0 0 0 0 0 0 0 R W Reset Figure 23-4. Port B Data Register (PORTB) Read: Anytime. Write: Anytime. Table 23-5. PORTB Field Descriptions Field Description 7-0 PB[7:0] Port B -- Port B pins 7-0 are associated with address outputs ADDR7 through ADDR1 respectively in expanded modes. Pin 0 is associated with output ADDR0 in emulation modes and special test mode and with Upper Data Select (UDS) in normal expanded mode. When this port is not used for external addresses, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 23.0.5.3 Port A Data Direction Register (DDRA) 7 6 5 4 3 2 1 0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0 0 0 0 0 0 0 0 R W Reset Figure 23-5. Port A Data Direction Register (DDRA) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-6. DDRA Field Descriptions Field Description 7-0 DDRA[7:0] Data Direction Port A -- This register controls the data direction for port A. When Port A is operating as a general purpose I/O port, DDRA determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTA after changing the DDRA register. 23.0.5.4 Port B Data Direction Register (DDRB) 7 6 5 4 3 2 1 0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 0 0 0 0 0 0 0 0 R W Reset Figure 23-6. Port B Data Direction Register (DDRB) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 23-7. DDRB Field Descriptions Field Description 7-0 DDRB[7:0] Data Direction Port B -- This register controls the data direction for port B. When Port B is operating as a general purpose I/O port, DDRB determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTB after changing the DDRB register. 23.0.5.5 Port C Data Register (PORTC) 7 6 5 4 3 2 1 0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 0 0 0 0 0 0 0 0 R W Reset Figure 23-7. Port C Data Register (PORTC) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. MC9S12XDP512 Data Sheet, Rev. 2.21 922 Freescale Semiconductor Table 23-8. PORTC Field Descriptions Field Description 7-0 PC[7:0] Port C -- Port C pins 7-0 can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 23.0.5.6 Port D Data Register (PORTD) 7 6 5 4 3 2 1 0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 0 0 0 0 0 0 0 0 R W Reset Figure 23-8. Port D Data Register (PORTD) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 23-9. PORTD Field Descriptions Field Description 7-0 PD[7:0] Port D -- Port D pins 7-0. -- If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 23.0.5.7 Port C Data Direction Register (DDRC) 7 6 5 4 3 2 1 0 DDRC7 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 0 0 0 0 0 0 0 0 R W Reset Figure 23-9. Port C Data Direction Register (DDRC) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 23-10. DDRC Field Descriptions Field Description 7-0 DDRC[7:0] Data Direction Port C -- This register controls the data direction for port C. DDRC determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTC after changing the DDRC register. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.8 Port D Data Direction Register (DDRD) 7 6 5 4 3 2 1 0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 0 0 0 0 0 0 0 0 R W Reset Figure 23-10. Port D Data Direction Register (DDRD) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data are read from this register. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 23-11. DDRD Field Descriptions Field Description 7-0 DDRD[7:0] Data Direction Port D -- This register controls the data direction for port D. DDRD determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTD after changing the DDRD register. 23.0.5.9 Port E Data Register (PORTE) 7 6 5 4 3 2 1 0 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 Alt. Func. XCLKS or ECLKX2 MODB or TAGHI MODA or RE or TAGLO ECLK EROMCTL or LSTRB or LDS R/W or WE IRQ XIRQ Reset 0 0 0 0 0 0 --1 --1 R W = Unimplemented or Reserved Figure 23-11. Port E Data Register (PORTE) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. MC9S12XDP512 Data Sheet, Rev. 2.21 924 Freescale Semiconductor Table 23-12. PORTE Field Descriptions Field Description 7-0 PE[7:0] Port E -- Port E bits 7-0 are associated with external bus control signals and interrupt inputs. These include mode select (MODB, MODA), E clock, double frequency E clock, Instruction Tagging High and Low (TAGHI, TAGLO), Read/Write (R/W), Read Enable and Write Enable (RE, WE), Lower Data Select (LDS), IRQ, and XIRQ. When not used for any of these specific functions, Port E pins 7-2 can be used as general purpose I/O and pins 1-0 can be used as general purpose inputs. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Pins 6 and 5 are inputs with enabled pull-down devices while RESET pin is low. Pins 7 and 3 are inputs with enabled pull-up devices while RESET pin is low. 23.0.5.10 Port E Data Direction Register (DDRE) 7 6 5 4 3 2 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 0 0 0 0 0 0 R 1 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 23-12. Port E Data Direction Register (DDRE) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 23-13. DDRE Field Descriptions Field Description 7-0 DDRE[7:2] Data Direction Port E -- his register controls the data direction for port E. When Port E is operating as a general purpose I/O port, DDRE determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. Port E bit 1 (associated with IRQ) and bit 0 (associated with XIRQ) cannot be configured as outputs. Port E, bits 1 and 0, can be read regardless of whether the alternate interrupt function is enabled. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTE after changing the DDRE register. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.11 S12X_EBI Ports, BKGD, VREGEN Pin Pull-up Control Register (PUCR) 7 6 PUPKE BKPUE 1 1 5 R 4 3 2 1 0 PUPEE PUPDE PUPCE PUPBE PUPAE 1 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 23-13. S12X_EBI Ports, BKGD, VREGEN Pin Pull-up Control Register (PUCR) Read: Anytime in single-chip modes. Write: Anytime, except BKPUE which is writable in special test mode only. This register is used to enable pull-up devices for the associated ports A, B, C, D, E, and K. Pull-up devices are assigned on a per-port basis and apply to any pin in the corresponding port currently configured as an input. Table 23-14. PUCR Field Descriptions Field Description 7 PUPKE Pull-up Port K Enable 0 Port K pull-up devices are disabled. 1 Enable pull-up devices for Port K input pins. 6 BKPUE BKGD and VREGEN Pin Pull-up Enable 0 BKGD and VREGEN pull-up devices are disabled. 1 Enable pull-up devices on BKGD and VREGEN pins. 4 PUPEE Pull-up Port E Enable 0 Port E pull-up devices on bit 7, 4-0 are disabled. 1 Enable pull-up devices for Port E input pins bits 7, 4-0. Note: Bits 5 and 6 of Port E have pull-down devices which are only enabled during reset. This bit has no effect on these pins. 3 PUPDE Pull-up Port D Enable 0 Port D pull-up devices are disabled. 1 Enable pull-up devices for all Port D input pins. 2 PUPCE Pull-up Port C Enable 0 Port C pull-up devices are disabled. 1 Enable pull-up devices for all Port C input pins. 1 PUPBE Pull-up Port B Enable 0 Port B pull-up devices are disabled. 1 Enable pull-up devices for all Port B input pins. 0 PUPAE Pull-up Port A Enable 0 Port A pull-up devices are disabled. 1 Enable pull-up devices for all Port A input pins. MC9S12XDP512 Data Sheet, Rev. 2.21 926 Freescale Semiconductor 23.0.5.12 S12X_EBI Ports Reduced Drive Register (RDRIV) 7 R 6 5 0 0 RDPK 4 3 2 1 0 RDPE RDPD RDPC RDPB RDPA 0 0 0 0 0 W Reset 0 0 0 = Unimplemented or Reserved Figure 23-14. S12X_EBI Ports Reduced Drive Register (RDRIV) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. This register is used to select reduced drive for the pins associated with ports A, B, E, and K. If enabled, the pins drive at about 1/6 of the full drive strength. The reduced drive function is independent of which function is being used on a particular pin. The reduced drive functionality does not take effect on the pins in emulation modes. Table 23-15. RDRIV Field Descriptions Field Description 7 RDPK Reduced Drive of Port K 0 All port K output pins have full drive enabled. 1 All port K output pins have reduced drive enabled. 4 RDPE Reduced Drive of Port E 0 All port E output pins have full drive enabled. 1 All port E output pins have reduced drive enabled. 3 RDPD Reduced Drive of Port D 0 All port D output pins have full drive enabled. 1 All port D output pins have reduced drive enabled. 2 RDPC Reduced Drive of Port C 0 All port C output pins have full drive enabled. 1 All port C output pins have reduced drive enabled. 1 RDPB Reduced Drive of Port B 0 All port B output pins have full drive enabled. 1 All port B output pins have reduced drive enabled. 0 RDPA Reduced Drive of Ports A 0 All Port A output pins have full drive enabled. 1 All port A output pins have reduced drive enabled. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.13 ECLK Control Register (ECLKCTL) 7 6 1 0 NECLK NCLKX2 EDIV1 EDIV0 Mode Dependent 1 0 0 0 0 0 0 Mode 0 1 0 0 0 0 0 0 Special Single-Chip 1 1 0 0 0 0 0 0 Emulation Single-Chip 0 1 0 0 0 0 0 0 Special Test 0 1 0 0 0 0 0 0 Emulation Expanded 1 1 0 0 0 0 0 0 Normal Single-Chip 0 1 0 0 0 0 0 0 Normal Expanded R 5 4 3 2 0 0 0 0 W Reset1 SS ES ST EX NS NX = Unimplemented or Reserved Figure 23-15. ECLK Control Register (ECLKCTL) 1. Reset values in emulation modes are identical to those of the target mode. Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. The ECLKCTL register is used to control the availability of the free-running clocks and the free-running clock divider. Table 23-16. ECLKCTL Field Descriptions Field 7 NECLK Description No ECLK -- This bit controls the availability of a free-running clock on the ECLK pin. Clock output is always active in emulation modes and if enabled in all other operating modes. 0 ECLK enabled 1 ECLK disabled MC9S12XDP512 Data Sheet, Rev. 2.21 928 Freescale Semiconductor Table 23-16. ECLKCTL Field Descriptions (continued) Field Description 6 NCLKX2 No ECLKX2 -- This bit controls the availability of a free-running clock on the ECLKX2 pin. This clock has a fixed rate of twice the internal bus clock. Clock output is always active in emulation modes and if enabled in all other operating modes. 0 ECLKX2 is enabled 1 ECLKX2 is disabled 1-0 EDIV[1:0] Free-Running ECLK Divider -- These bits determine the rate of the free-running clock on the ECLK pin. The usage of the bits is shown in Table 23-17. Divider is always disabled in emulation modes and active as programmed in all other operating modes. Table 23-17. Free-Running ECLK Clock Rate EDIV[1:0] Rate of Free-Running ECLK 00 ECLK = Bus clock rate 01 ECLK = Bus clock rate divided by 2 10 ECLK = Bus clock rate divided by 3 11 ECLK = Bus clock rate divided by 4 23.0.5.14 IRQ Control Register (IRQCR) 7 6 IRQE IRQEN 0 1 R 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 23-16. IRQ Control Register (IRQCR) Read: See individual bit descriptions below. Write: See individual bit descriptions below. Table 23-18. IRQCR Field Descriptions Field 7 IRQE 6 IRQEN Description IRQ Select Edge Sensitive Only Special modes: Read or write anytime. Normal and emulation modes: Read anytime, write once. 0 IRQ configured for low level recognition. 1 IRQ configured to respond only to falling edges. Falling edges on the IRQ pin will be detected anytime IRQE = 1 and will be cleared only upon a reset or the servicing of the IRQ interrupt. External IRQ Enable Read or write anytime. 0 External IRQ pin is disconnected from interrupt logic. 1 External IRQ pin is connected to interrupt logic. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.15 Port K Data Register (PORTK) 7 6 5 4 3 2 1 0 PK7 PK6 PK5 PK4 PK3 PK2 PK1 PK0 Alt. Func. ROMCTL or EWAIT ADDR22 mux NOACC ADDR21 ADDR20 ADDR19 mux IQSTAT3 ADDR18 mux IQSTAT2 ADDR17 mux IQSTAT1 ADDR16 mux IQSTAT0 Reset 0 0 0 0 0 0 0 0 R W Figure 23-17. Port K Data Register (PORTK) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. Table 23-19. PORTK Field Descriptions Field Description 7-0 PK[7:0] Port K -- Port K pins 7-0 are associated with external bus control signals and internal memory expansion emulation pins. These include ADDR22-ADDR16, No-Access (NOACC), External Wait (EWAIT) and instruction pipe signals IQSTAT3-IQSTAT0. Bits 6-0 carry the external addresses in all expanded modes. In emulation or special test mode with internal visibility enabled the address is multiplexed with the alternate functions NOACC and IQSTAT on the respective pins. In single-chip modes the port pins can be used as general-purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 23.0.5.16 Port K Data Direction Register (DDRK) 7 6 5 4 3 2 1 0 DDRK7 DDRK6 DDRK5 DDRK4 DDRK3 DDRK2 DDRK1 DDRK0 0 0 0 0 0 0 0 0 R W Reset Figure 23-18. Port K Data Direction Register (DDRK) Read: Anytime. In emulation modes, read operations will return the data from the external bus, in all other modes the data source is depending on the data direction value. Write: Anytime. In emulation modes, write operations will also be directed to the external bus. This register controls the data direction for port K. When Port K is operating as a general purpose I/O port, DDRK determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. MC9S12XDP512 Data Sheet, Rev. 2.21 930 Freescale Semiconductor Table 23-20. DDRK Field Descriptions Field Description 7-0 DDRK[7:0] Data Direction Port K 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTK after changing the DDRK register. 23.0.5.17 Port T Data Register (PTT) 7 6 5 4 3 2 1 0 PTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0 IOC7 IOC6 IOC5 IOC4 IOC3 IOC2 IOC1 IOC0 0 0 0 0 0 0 0 0 R W ECT Reset Figure 23-19. Port T Data Register (PTT) Read: Anytime. Write: Anytime. Table 23-21. PTT Field Descriptions Field Description 7-0 PTT[7:0] Port T -- Port T bits 7-0 are associated with ECT channels IOC7-IOC0 (refer to ECT section). When not used with the ECT, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 23.0.5.18 Port T Input Register (PTIT) R 7 6 5 4 3 2 1 0 PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 23-20. Port T Input Register (PTIT) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-22. PTIT Field Descriptions Field Description 7-0 PTIT[7:0] Port T Input -- This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. 23.0.5.19 Port T Data Direction Register (DDRT) 7 6 5 4 3 2 1 0 DDRT7 DDRT6 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0 0 0 0 0 0 0 0 0 R W Reset Figure 23-21. Port T Data Direction Register (DDRT) Read: Anytime. Write: Anytime. This register configures each port T pin as either input or output. The ECT forces the I/O state to be an output for each timer port associated with an enabled output compare. In this case the data direction bits will not change. The DDRT bits revert to controlling the I/O direction of a pin when the associated timer output compare is disabled. The timer input capture always monitors the state of the pin. Table 23-23. DDRT Field Descriptions Field Description 7-0 DDRT[7:0] Data Direction Port T 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTT or PTIT registers, when changing the DDRT register. 23.0.5.20 Port T Reduced Drive Register (RDRT) 7 6 5 4 3 2 1 0 RDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0 0 0 0 0 0 0 0 0 R W Reset Figure 23-22. Port T Reduced Drive Register (RDRT) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 932 Freescale Semiconductor This register configures the drive strength of each port T output pin as either full or reduced. If the port is used as input this bit is ignored. Table 23-24. RDRT Field Descriptions Field 7-0 RDRT[7:0] Description Reduced Drive Port T 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.21 Port T Pull Device Enable Register (PERT) 7 6 5 4 3 2 1 0 PERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0 0 0 0 0 0 0 0 0 R W Reset Figure 23-23. Port T Pull Device Enable Register (PERT) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 23-25. PERT Field Descriptions Field 7-0 PERT[7:0] Description Pull Device Enable Port T 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 23.0.5.22 Port T Polarity Select Register (PPST) 7 6 5 4 3 2 1 0 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0 0 0 0 0 0 0 0 R W Reset Figure 23-24. Port T Polarity Select Register (PPST) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-26. PPST Field Descriptions Field Description 7-0 PPST[7:0] Pull Select Port T 0 A pull-up device is connected to the associated port T pin, if enabled by the associated bit in register PERT and if the port is used as input. 1 A pull-down device is connected to the associated port T pin, if enabled by the associated bit in register PERT and if the port is used as input. 23.0.5.23 Port S Data Register (PTS) 7 6 5 4 3 2 1 0 PTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0 SS0 SCK0 MOSI0 MISO0 TXD1 RXD1 TXD0 RXD0 0 0 0 0 0 0 0 0 R W SCI/SPI Reset Figure 23-25. Port S Data Register (PTS) Read: Anytime. Write: Anytime. Port S pins 7-4 are associated with the SPI0. The SPI0 pin configuration is determined by several status bits in the SPI0 module. Refer to SPI section for details. When not used with the SPI0, these pins can be used as general purpose I/O. Port S bits 3-0 are associated with the SCI1 and SCI0. The SCI ports associated with transmit pins 3 and 1 are configured as outputs if the transmitter is enabled. The SCI ports associated with receive pins 2 and 0 are configured as inputs if the receiver is enabled. Refer to SCI section for details. When not used with the SCI, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 23.0.5.24 Port S Input Register (PTIS) R 7 6 5 4 3 2 1 0 PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 23-26. Port S Input Register (PTIS) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. MC9S12XDP512 Data Sheet, Rev. 2.21 934 Freescale Semiconductor Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This also can be used to detect overload or short circuit conditions on output pins. 23.0.5.25 Port S Data Direction Register (DDRS) 7 6 5 4 3 2 1 0 DDRS7 DDRS6 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0 0 0 0 0 0 0 0 0 R W Reset Figure 23-27. Port S Data Direction Register (DDRS) Read: Anytime. Write: Anytime. This register configures each port S pin as either input or output. If SPI0 is enabled, the SPI0 determines the pin direction. Refer to SPI section for details. If the associated SCI transmit or receive channel is enabled this register has no effect on the pins. The pin is forced to be an output if a SCI transmit channel is enabled, it is forced to be an input if the SCI receive channel is enabled. The DDRS bits revert to controlling the I/O direction of a pin when the associated channel is disabled. Table 23-27. DDRS Field Descriptions Field Description 7-0 DDRS[7:0] Data Direction Port S 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTS or PTIS registers, when changing the DDRS register. 23.0.5.26 Port S Reduced Drive Register (RDRS) 7 6 5 4 3 2 1 0 RDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0 0 0 0 0 0 0 0 0 R W Reset Figure 23-28. Port S Reduced Drive Register (RDRS) Read: Anytime. Write: Anytime. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) This register configures the drive strength of each port S output pin as either full or reduced. If the port is used as input this bit is ignored. Table 23-28. RDRS Field Descriptions Field 7-0 RDRS[7:0] Description Reduced Drive Port S 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.27 Port S Pull Device Enable Register (PERS) 7 6 5 4 3 2 1 0 PERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0 1 1 1 1 1 1 1 1 R W Reset Figure 23-29. Port S Pull Device Enable Register (PERS) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or as output in wired-OR (open drain) mode. This bit has no effect if the port is used as push-pull output. Out of reset a pull-up device is enabled. Table 23-29. PERS Field Descriptions Field 7-0 PERS[7:0] Description Pull Device Enable Port S 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 23.0.5.28 Port S Polarity Select Register (PPSS) 7 6 5 4 3 2 1 0 PPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0 0 0 0 0 0 0 0 0 R W Reset Figure 23-30. Port S Polarity Select Register (PPSS) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. MC9S12XDP512 Data Sheet, Rev. 2.21 936 Freescale Semiconductor Table 23-30. PPSS Field Descriptions Field Description 7-0 PPSS[7:0] Pull Select Port S 0 A pull-up device is connected to the associated port S pin, if enabled by the associated bit in register PERS and if the port is used as input or as wired-OR output. 1 A pull-down device is connected to the associated port S pin, if enabled by the associated bit in register PERS and if the port is used as input. 23.0.5.29 Port S Wired-OR Mode Register (WOMS) 7 6 5 4 3 2 1 0 WOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0 0 0 0 0 0 0 0 0 R W Reset Figure 23-31. Port S Wired-OR Mode Register (WOMS) Read: Anytime. Write: Anytime. This register configures the output pins as wired-OR. If enabled the output is driven active low only (open-drain). A logic level of "1" is not driven. It applies also to the SPI and SCI outputs and allows a multipoint connection of several serial modules. These bits have no influence on pins used as inputs. Table 23-31. WOMS Field Descriptions Field 7-0 Wired-OR Mode Port S WOMS[7:0] 0 Output buffers operate as push-pull outputs. 1 Output buffers operate as open-drain outputs. Description Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.30 Port M Data Register (PTM) 7 6 5 4 3 2 1 0 PTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0 CAN TXCAN2 RXCAN2 TXCAN1 RXCAN1 TXCAN0 RXCAN0 Routed CAN0 TXCAN0 RXCAN0 TXCAN0 RXCAN0 TXCAN4 RXCAN4 SCK0 MOSI0 SS0 MISO0 0 0 0 0 0 0 R W Routed CAN4 TXCAN4 RXCAN4 Routed SPI0 Reset 0 0 Figure 23-32. Port M Data Register (PTM) Read: Anytime. Write: Anytime. Port M pins 7-0 are associated with the CAN0, CAN1, CAN2, as well as the routed CAN0, CAN4, and SPI0 modules. When not used with any of the peripherals, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Table 23-32. PTM Field Descriptions Field Description 7-6 PTM[7:6] The CAN4 function (TXCAN4 and RXCAN4) takes precedence over the general purpose I/O function if the CAN4 module is enabled. Refer to MSCAN section for details. 5-4 PTM[5:4] The CAN2 function (TXCAN2 and RXCAN2) takes precedence over the routed CAN0, routed CAN4, the routed SPI0 and the general purpose I/O function if the CAN2 module is enabled. The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the routed CAN4, the routed SPI0 and the general purpose I/O function if the routed CAN0 module is enabled. The routed CAN4 function (TXCAN4 and RXCAN4) takes precedence over the routed SPI0 and general purpose I/O function if the routed CAN4 module is enabled. Refer to MSCAN section for details. The routed SPI0 function (SCK0 and MOSI0) takes precedence of the general purpose I/O function if the routed SPI0 is enabled. Refer to SPI section for details. 3-2 PTM[3:2] The CAN1 function (TXCAN1 and RXCAN1) takes precedence over the routed CAN0, the routed SPI0 and the general purpose I/O function if the CAN1 module is enabled.The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the routed SPI0 and the general purpose I/O function if the routed CAN0 module is enabled. Refer to MSCAN section for details. The routed SPI0 function (SS0 and MISO0) takes precedence of the general purpose I/O function if the routed SPI0 is enabled and not in bidirectional mode. Refer to SPI section for details. 1-0 PTM[1:0] The CAN0 function (TXCAN0 and RXCAN0) takes precedence over the general purpose I/O function if the CAN0 module is enabled. Refer to MSCAN section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 938 Freescale Semiconductor 23.0.5.31 Port M Input Register (PTIM) R 7 6 5 4 3 2 1 0 PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 23-33. Port M Input Register (PTIM) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. 23.0.5.32 Port M Data Direction Register (DDRM) 7 6 5 4 3 2 1 0 DDRM7 DDRM6 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0 0 0 0 0 0 0 0 0 R W Reset Figure 23-34. Port M Data Direction Register (DDRM) Read: Anytime. Write: Anytime. This register configures each port M pin as either input or output. The CAN forces the I/O state to be an output for each port line associated with an enabled output (TXCAN). also forces the I/O state to be an input for each port line associated with an enabled input (RXCAN). In those cases the data direction bits will not change. The DDRM bits revert to controlling the I/O direction of a pin when the associated peripheral module is disabled. Table 23-33. DDRM Field Descriptions Field Description 7-0 DDRM[7:0] Data Direction Port M 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTM or PTIM registers, when changing the DDRM register. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.33 Port M Reduced Drive Register (RDRM) 7 6 5 4 3 2 1 0 RDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0 0 0 0 0 0 0 0 0 R W Reset Figure 23-35. Port M Reduced Drive Register (RDRM) Read: Anytime. Write: Anytime. This register configures the drive strength of each Port M output pin as either full or reduced. If the port is used as input this bit is ignored. Table 23-34. RDRM Field Descriptions Field 7-0 RDRM[7:0] Description Reduced Drive Port M 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.34 Port M Pull Device Enable Register (PERM) 7 6 5 4 3 2 1 0 PERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0 0 0 0 0 0 0 0 0 R W Reset Figure 23-36. Port M Pull Device Enable Register (PERM) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset no pull device is enabled. Table 23-35. PERM Field Descriptions Field 7-0 PERM[7:0] Description Pull Device Enable Port M 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 940 Freescale Semiconductor 23.0.5.35 Port M Polarity Select Register (PPSM) 7 6 5 4 3 2 1 0 PPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0 0 0 0 0 0 0 0 0 R W Reset Figure 23-37. Port M Polarity Select Register (PPSM) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. If CAN is active, a pull-up device can be activated on the related RXCAN inputs, but not a pull-down. Table 23-36. PPSM Field Descriptions Field Description 7-0 PPSM[7:0] Pull Select Port M 0 A pull-up device is connected to the associated port M pin, if enabled by the associated bit in register PERM and if the port is used as general purpose or RXCAN input. 1 A pull-down device is connected to the associated port M pin, if enabled by the associated bit in register PERM and if the port is used as a general purpose but not as RXCAN. 23.0.5.36 Port M Wired-OR Mode Register (WOMM) 7 6 5 4 3 2 1 0 WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 0 0 0 0 0 0 0 0 R W Reset Figure 23-38. Port M Wired-OR Mode Register (WOMM) Read: Anytime. Write: Anytime. This register configures the output pins as wired-OR. If enabled the output is driven active low only (open-drain). A logic level of "1" is not driven. It applies also to the CAN outputs and allows a multipoint connection of several serial modules. This bit has no influence on pins used as inputs. Table 23-37. WOMM Field Descriptions Field 7-0 Wired-OR Mode Port M WOMM[7:0] 0 Output buffers operate as push-pull outputs. 1 Output buffers operate as open-drain outputs. Description Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.37 Module Routing Register (MODRR) 7 R 6 5 4 3 2 1 0 MODRR6 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0 0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 23-39. Module Routing Register (MODRR) Read: Anytime. Write: Anytime. This register configures the re-routing of CAN0, CAN4, SPI0, SPI1, and SPI2 on alternative ports. Table 23-38. Module Routing Summary MODRR Related Pins Module CAN0 CAN4 6 5 4 3 2 1 0 RXCAN TXCAN x x x x x 0 0 PM0 PM1 x x x x x 0 1 PM2 PM3 x x x x x 1 0 PM4 PM5 x x x x x 1 1 PJ6 PJ7 x x x 0 0 x x PJ6 PJ7 x x x 0 1 x x PM4 PM5 x x x 1 0 x x PM6 PM7 x x x 1 1 x x Reserved MISO SPI0 SPI1 SPI2 MOSI SCK SS x x 0 x x x x PS4 PS5 PS6 PS7 x x 1 x x x x PM2 PM4 PM5 PM3 x 0 x x x x x PP0 PP1 PP2 PP3 x 1 x x x x x PH0 PH1 PH2 PH3 0 x x x x x x PP4 PP5 PP7 PP6 1 x x x x x x PH4 PH5 PH6 PH7 MC9S12XDP512 Data Sheet, Rev. 2.21 942 Freescale Semiconductor 23.0.5.38 Port P Data Register (PTP) 7 6 5 4 3 2 1 0 PTP7 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0 PWM PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 SPI SCK2 SS2 MOSI2 MISO2 SS1 SCK1 MOSI1 MISO1 0 0 0 0 0 0 0 0 R W Reset Figure 23-40. Port P Data Register (PTP) Read: Anytime. Write: Anytime. Port P pins 7-0 are associated with the PWM as well as the SPI1 and SPI2. These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. The PWM function takes precedence over the general purpose I/O and the SPI2 or SPI1 function if the associated PWM channel is enabled. While channels 6-0 are output only if the respective channel is enabled, channel 7 can be PWM output or input if the shutdown feature is enabled. Refer to PWM section for details. The SPI2 function takes precedence over the general purpose I/O function if enabled. Refer to SPI section for details. The SPI1 function takes precedence over the general purpose I/O function if enabled. Refer to SPI section for details. 23.0.5.39 Port P Input Register (PTIP) R 7 6 5 4 3 2 1 0 PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 23-41. Port P Input Register (PTIP) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.40 Port P Data Direction Register (DDRP) 7 6 5 4 3 2 1 0 DDRP7 DDRP6 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0 0 0 0 0 0 0 0 0 R W Reset Figure 23-42. Port P Data Direction Register (DDRP) Read: Anytime. Write: Anytime. This register configures each port P pin as either input or output. If the associated PWM channel or SPI module is enabled this register has no effect on the pins. The PWM forces the I/O state to be an output for each port line associated with an enabled PWM7-0 channel. Channel 7 can force the pin to input if the shutdown feature is enabled. Refer to PWM section for details. If SPI is enabled, the SPI determines the pin direction. Refer to SPI section for details. The DDRP bits revert to controlling the I/O direction of a pin when the associated peripherals are disabled. Table 23-39. DDRP Field Descriptions Field Description 7-0 DDRP[7:0] Data Direction Port P 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTP or PTIP registers, when changing the DDRP register. 23.0.5.41 Port P Reduced Drive Register (RDRP) 7 6 5 4 3 2 1 0 RDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0 0 0 0 0 0 0 0 0 R W Reset Figure 23-43. Port P Reduced Drive Register (RDRP) Read: Anytime. Write: Anytime. This register configures the drive strength of each port P output pin as either full or reduced. If the port is used as input this bit is ignored. MC9S12XDP512 Data Sheet, Rev. 2.21 944 Freescale Semiconductor Table 23-40. RDRP Field Descriptions Field 7-0 RDRP[7:0] Description Reduced Drive Port P 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.42 Port P Pull Device Enable Register (PERP) 7 6 5 4 3 2 1 0 PERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0 0 0 0 0 0 0 0 0 R W Reset Figure 23-44. Port P Pull Device Enable Register (PERP) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 23-41. PERP Field Descriptions Field 7-0 PERP[7:0] Description Pull Device Enable Port P 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 23.0.5.43 Port P Polarity Select Register (PPSP) 7 6 5 4 3 2 1 0 PPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSP0 0 0 0 0 0 0 0 0 R W Reset Figure 23-45. Port P Polarity Select Register (PPSP) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-42. PPSP Field Descriptions Field Description 7-0 PPSP[7:0] Polarity Select Port P 0 Falling edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-up device is connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is used as input. 1 Rising edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-down device is connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is used as input. 23.0.5.44 Port P Interrupt Enable Register (PIEP) 7 6 5 4 3 2 1 0 PIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0 0 0 0 0 0 0 0 0 R W Reset Figure 23-46. Port P Interrupt Enable Register (PIEP) Read: Anytime. Write: Anytime. This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port P. Table 23-43. PIEP Field Descriptions Field 7-0 PIEP[7:0] Description Interrupt Enable Port P 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. 23.0.5.45 Port P Interrupt Flag Register (PIFP) 7 6 5 4 3 2 1 0 PIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0 0 0 0 0 0 0 0 0 R W Reset Figure 23-47. Port P Interrupt Flag Register (PIFP) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 946 Freescale Semiconductor Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSP register. To clear this flag, write logic level "1" to the corresponding bit in the PIFP register. Writing a "0" has no effect. Table 23-44. PIFP Field Descriptions Field 7-0 PIFP[7:0] Description Interrupt Flags Port P 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. 23.0.5.46 Port H Data Register (PTH) 7 6 5 4 3 2 1 0 PTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0 TXD4 RXD4 R W SCI Routed SPI Reset SS2 SCK2 MOSI2 MISO2 SS1 SCK1 MOSI1 MISO1 0 0 0 0 0 0 0 0 Figure 23-48. Port H Data Register (PTH) Read: Anytime. Write: Anytime. Port H pins 7-0 are associated with the SCI4 as well as the routed SPI1 and SPI2. These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. The routed SPI2 function takes precedence over the SCI4 and the general purpose I/O function if the routed SPI2 module is enabled. Refer to SPI section for details.The routed SPI1 function takes precedence over the general purpose I/O function if the routed SPI1 is enabled. Refer to SPI section for details. The SCI4 function takes precedence over the general purpose I/O function if the SCI4 is enabled Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.47 Port H Input Register (PTIH) R 7 6 5 4 3 2 1 0 PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 23-49. Port H Input Register (PTIH) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. 23.0.5.48 Port H Data Direction Register (DDRH) 7 6 5 4 3 2 1 0 DDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 0 0 0 0 0 0 0 0 R W Reset Figure 23-50. Port H Data Direction Register (DDRH) Read: Anytime. Write: Anytime. This register configures each port H pin as either input or output. If the associated routed SPI module is enabled this register has no effect on the pins. The SCI forces the I/O state to be an output for each port line associated with an enabled output ( TXD4). It also forces the I/O state to be an input for each port line associated with an enabled input ( RXD4). In those cases the data direction bits will not change. If a SPI module is enabled, the SPI determines the pin direction. Refer to SPI section for details. The DDRH bits revert to controlling the I/O direction of a pin when the associated peripheral modules are disabled. MC9S12XDP512 Data Sheet, Rev. 2.21 948 Freescale Semiconductor Table 23-45. DDRH Field Descriptions Field Description 7-0 DDRH[7:0] Data Direction Port H 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTH or PTIH registers, when changing the DDRH register. 23.0.5.49 Port H Reduced Drive Register (RDRH) 7 6 5 4 3 2 1 0 RDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0 0 0 0 0 0 0 0 0 R W Reset Figure 23-51. Port H Reduced Drive Register (RDRH) Read: Anytime. Write: Anytime. This register configures the drive strength of each Port H output pin as either full or reduced. If the port is used as input this bit is ignored. Table 23-46. RDRH Field Descriptions Field 7-0 RDRH[7:0] Description Reduced Drive Port H 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.50 Port H Pull Device Enable Register (PERH) 7 6 5 4 3 2 1 0 PERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0 0 0 0 0 0 0 0 0 R W Reset Figure 23-52. Port H Pull Device Enable Register (PERH) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-47. PERH Field Descriptions Field 7-0 PERH[7:0] Description Pull Device Enable Port H 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 23.0.5.51 Port H Polarity Select Register (PPSH) 7 6 5 4 3 2 1 0 PPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0 0 0 0 0 0 0 0 0 R W Reset Figure 23-53. Port H Polarity Select Register (PPSH) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. Table 23-48. PPSH Field Descriptions Field Description 7-0 PPSH[7:0] Polarity Select Port H 0 Falling edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-up device is connected to the associated port H pin, if enabled by the associated bit in register PERH and if the port is used as input. 1 Rising edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-down device is connected to the associated port H pin, if enabled by the associated bit in register PERH and if the port is used as input. 23.0.5.52 Port H Interrupt Enable Register (PIEH) 7 6 5 4 3 2 1 0 PIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0 0 0 0 0 0 0 0 0 R W Reset Figure 23-54. Port H Interrupt Enable Register (PIEH) Read: Anytime. Write: Anytime. This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port H. MC9S12XDP512 Data Sheet, Rev. 2.21 950 Freescale Semiconductor Table 23-49. PIEH Field Descriptions Field 7-0 PIEH[7:0] Description Interrupt Enable Port H 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. 23.0.5.53 Port H Interrupt Flag Register (PIFH) 7 6 5 4 3 2 1 0 PIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0 0 0 0 0 0 0 0 0 R W Reset Figure 23-55. Port H Interrupt Flag Register (PIFH) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSH register. To clear this flag, write logic level "1" to the corresponding bit in the PIFH register. Writing a "0" has no effect. Table 23-50. PIFH Field Descriptions Field 7-0 PIFH[7:0] Description Interrupt Flags Port H 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.54 Port J Data Register (PTJ) 7 6 5 4 PTJ7 PTJ6 PTJ5 PTJ4 TXCAN4 RXCAN4 R 3 2 1 0 PTJ2 PTJ1 PTJ0 TXD2 RXD2 0 W CAN4 SCI2 IIC0 Routed CAN0 SCL0 SDA0 TXCAN0 RXCAN0 Alt. Function Reset 0 0 CS2 CS0 0 0 CS1 0 0 CS3 0 0 = Unimplemented or Reserved Figure 23-56. Port J Data Register (PTJ) Read: Anytime. Write: Anytime. Port J pins 7-4 and 2-0 are associated with the CAN4, SCI2, IIC0, the routed CAN0 modules and chip select signals (CS0, CS1, CS2, CS3). These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Table 23-51. PTJ Field Descriptions Field Description 7-6 PJ[7:6] The CAN4 function (TXCAN4 and RXCAN4) takes precedence over the IIC0, the routed CAN0 and the general purpose I/O function if the CAN4 module is enabled. The IIC0 function (SCL0 and SDA0) takes precedence over the routed CAN0 and the general purpose I/O function if the IIC0 is enabled. If the IIC0 module takes precedence the SDA0 and SCL0 outputs are configured as open drain outputs. Refer to IIC section for details. The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the general purpose I/O function if the routed CAN0 module is enabled. Refer to MSCAN section for details. 2 PJ2 The chip select function (CS1) takes precedence over the general purpose I/O. 1 PJ1 The SCI2 function takes precedence over the general purpose I/O function if the SCI2 module is enabled. Refer to SCI section for details. 0 PJ0 The chip select (CS3) takes precedence over the general purpose I/O function. MC9S12XDP512 Data Sheet, Rev. 2.21 952 Freescale Semiconductor 23.0.5.55 Port J Input Register (PTIJ) R 7 6 5 4 3 2 1 0 PTIJ7 PTIJ6 PTIJ5 PTIJ4 0 PTIJ2 PTIJ1 PTIJ0 0 0 0 0 0 0 0 0 W Reset1 = Unimplemented or Reserved Figure 23-57. Port J Input Register (PTIJ) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can be used to detect overload or short circuit conditions on output pins. 23.0.5.56 Port J Data Direction Register (DDRJ) 7 6 5 4 DDRJ7 DDRJ6 DDRJ5 DDRJ4 0 0 0 0 R 3 2 1 0 DDRJ2 DDRJ1 DDRJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 23-58. Port J Data Direction Register (DDRJ) Read: Anytime. Write: Anytime. This register configures each port J pin as either input or output. The CAN forces the I/O state to be an output on PJ7 (TXCAN4) and an input on pin PJ6 (RXCAN4). The IIC takes control of the I/O if enabled. In these cases the data direction bits will not change. The SCI2 forces the I/O state to be an output for each port line associated with an enabled output (TXD2). It also forces the I/O state to be an input for each port line associated with an enabled input (RXD2). In these cases the data direction bits will not change. The DDRJ bits revert to controlling the I/O direction of a pin when the associated peripheral module is disabled. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-52. DDRJ Field Descriptions Field Description 7-0 DDRJ[7:4] DDRJ[2:0] Data Direction Port J 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTJ or PTIJ registers, when changing the DDRJ register. 23.0.5.57 Port J Reduced Drive Register (RDRJ) 7 6 5 4 3 RDRJ7 RDRJ6 RDRJ5 RDRJ4 0 0 0 0 R 2 1 0 RDRJ2 RDRJ1 RDRJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 23-59. Port J Reduced Drive Register (RDRJ) Read: Anytime. Write: Anytime. This register configures the drive strength of each port J output pin as either full or reduced. If the port is used as input this bit is ignored. Table 23-53. RDRJ Field Descriptions Field 7-0 RDRJ[7:4] RDRJ[2:0] Description Reduced Drive Port J 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.58 Port J Pull Device Enable Register (PERJ) 7 6 5 4 PERJ7 PERJ6 PERJ5 PERJ4 1 1 1 1 R 3 2 1 0 PERJ2 PERJ1 PERJ0 1 1 1 0 W Reset 0 = Unimplemented or Reserved Figure 23-60. Port J Pull Device Enable Register (PERJ) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 954 Freescale Semiconductor This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or as wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset a pull-up device is enabled. Table 23-54. PERJ Field Descriptions Field 7-0 PERJ[7:4] PERJ[2:0] Description Pull Device Enable Port J 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 23.0.5.59 Port J Polarity Select Register (PPSJ) 7 6 5 4 3 PPSJ7 PPSJ6 PPSJ5 PPSJ4 0 0 0 0 R 2 1 0 PPSJ2 PPSJ1 PPSJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 23-61. Port J Polarity Select Register (PPSJ) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. Table 23-55. PPSJ Field Descriptions Field Description 7-0 PPSJ[7:4] PPSJ[2:0] Polarity Select Port J 0 Falling edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-up device is connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is used as general purpose input or as IIC port. 1 Rising edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-down device is connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is used as input. 23.0.5.60 Port J Interrupt Enable Register (PIEJ) 7 6 5 4 PIEJ7 PIEJ6 PIEJ5 PIEJ4 0 0 0 0 R 3 2 1 0 PIEJ2 PIEJ1 PIEJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 23-62. Port J Interrupt Enable Register (PIEJ) Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port J. Table 23-56. PIEJ Field Descriptions Field 7-0 PIEJ[7:4] PIEJ[2:0] Description Interrupt Enable Port J 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. 23.0.5.61 Port J Interrupt Flag Register (PIFJ) 7 6 5 4 PIFJ7 PIFJ6 PIFJ5 PIFJ4 0 0 0 0 3 R 2 1 0 PIFJ2 PIFJ1 PIFJ0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 23-63. Port J Interrupt Flag Register (PIFJ) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSJ register. To clear this flag, write logic level "1" to the corresponding bit in the PIFJ register. Writing a "0" has no effect. Table 23-57. PIEJ Field Descriptions Field 7-0 PIFJ[7:4] PIFJ[2:0] Description Interrupt Flags Port J 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. 23.0.5.62 Port AD0 Data Register 1 (PT1AD0) 7 6 5 4 3 2 1 0 PT1AD07 PT1AD06 PT1AD05 PT1AD04 PT1AD03 PT1AD02 PT1AD01 PT1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 23-64. Port AD0 Data Register 1 (PT1AD0) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 956 Freescale Semiconductor This register is associated with AD0 pins PAD[23:10]. These pins can also be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. 23.0.5.63 Port AD0 Data Direction Register 1 (DDR1AD0) 7 6 5 4 3 2 1 0 DDR1AD07 DDR1AD06 DDR1AD05 DDR1AD04 DDR1AD03 DDR1AD02 DDR1AD01 DDR1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 23-65. Port AD0 Data Direction Register 1 (DDR1AD0) Read: Anytime. Write: Anytime. This register configures pins PAD[07:00] as either input or output. Table 23-58. DDR1AD0 Field Descriptions Field Description 7-0 DDR1AD0[7:0] Data Direction Port AD0 Register 1 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD01 register, when changing the DDR1AD0 register. Note: To use the digital input function on port AD0 the ATD0 digital input enable register (ATD0DIEN) has to be set to logic level "1". 23.0.5.64 Port AD0 Reduced Drive Register 1 (RDR1AD0) 7 6 5 4 3 2 1 0 RDR1AD07 RDR1AD06 RDR1AD05 RDR1AD04 RDR1AD03 RDR1AD02 RDR1AD01 RDR1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 23-66. Port AD0 Reduced Drive Register 1 (RDR1AD0) Read: Anytime. Write: Anytime. This register configures the drive strength of each output pin PAD[07:00] as either full or reduced. If the port is used as input this bit is ignored. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-59. RDR1AD0 Field Descriptions Field Description 7-0 RDR1AD0[7:0] Reduced Drive Port AD0 Register 1 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.65 Port AD0 Pull Up Enable Register 1 (PER1AD0) 7 6 5 4 3 2 1 0 PER1AD07 PER1AD06 PER1AD05 PER1AD04 PER1AD03 PER1AD02 PER1AD01 PER1AD00 0 0 0 0 0 0 0 0 R W Reset Figure 23-67. Port AD0 Pull Up Enable Register 1 (PER1AD0) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective pin PAD[07:00] if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 23-60. PER1AD0 Field Descriptions Field Description 7-0 PER1AD0[7:0] Pull Device Enable Port AD0 Register 1 0 Pull-up device is disabled. 1 Pull-up device is enabled. 23.0.5.66 Port AD1 Data Register 0 (PT0AD1) 7 R PT0AD123 W Reset 0 6 5 4 3 2 1 0 PT0AD122 PT0AD121 PT0AD120 PT0AD119 PT0AD118 PT0AD117 PT0AD116 0 0 0 0 0 0 0 Figure 23-68. Port AD1 Data Register 0 (PT0AD1) Read: Anytime. Write: Anytime. This register is associated with AD1 pins PAD[23:16]. These pins can also be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. MC9S12XDP512 Data Sheet, Rev. 2.21 958 Freescale Semiconductor 23.0.5.67 Port AD1 Data Register 1 (PT1AD1) 7 6 5 4 3 2 1 0 PT1AD115 PT1AD114 PT1AD113 PT1AD112 PT1AD111 PT1AD110 PT1AD19 PT1AD18 0 0 0 0 0 0 0 0 R W Reset Figure 23-69. Port AD1 Data Register 1 (PT1AD1) Read: Anytime. Write: Anytime. This register is associated with AD1 pins PAD[15:8]. These pins can also be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. 23.0.5.68 Port AD1 Data Direction Register 0 (DDR0AD1) 7 6 5 4 3 2 1 0 R DDR0AD123 DDR0AD122 DDR0AD121 DDR0AD120 DDR0AD119 DDR0AD118 DDR0AD117 DDR0AD116 W Reset 0 0 0 0 0 0 0 0 Figure 23-70. Port AD1 Data Direction Register 0 (DDR0AD1) Read: Anytime. Write: Anytime. This register configures pin PAD[23:16] as either input or output. Table 23-61. DDR0AD1 Field Descriptions Field Description 7-0 Data Direction Port AD1 Register 0 DDR0AD1[23:16] 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD10 register, when changing the DDR0AD1 register. Note: To use the digital input function on Port AD1 the ATD1 digital input enable register (ATD1DIEN0) has to be set to logic level "1". Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.69 Port AD1 Data Direction Register 1 (DDR1AD1) 7 6 5 4 3 2 1 0 R DDR1AD115 DDR1AD114 DDR1AD113 DDR1AD112 DDR1AD111 DDR1AD110 DDR1AD19 DDR1AD18 W Reset 0 0 0 0 0 0 0 0 Figure 23-71. Port AD1 Data Direction Register 1 (DDR1AD1) Read: Anytime. Write: Anytime. This register configures pins PAD as either input or output. Table 23-62. DDR1AD1 Field Descriptions Field Description 7-0 DDR1AD1[15:8] Data Direction Port AD1 Register 1 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD11 register, when changing the DDR1AD1 register. Note: To use the digital input function on port AD1 the ATD1 digital input enable register (ATD1DIEN1) has to be set to logic level "1". 23.0.5.70 Port AD1 Reduced Drive Register 0 (RDR0AD1) 7 6 5 4 3 2 1 0 R RDR0AD123 RDR0AD122 RDR0AD121 RDR0AD120 RDR0AD119 RDR0AD118 RDR0AD117 RDR0AD116 W Reset 0 0 0 0 0 0 0 0 Figure 23-72. Port AD1 Reduced Drive Register 0 (RDR0AD1) Read: Anytime. Write: Anytime. This register configures the drive strength of each PAD[23:16] output pin as either full or reduced. If the port is used as input this bit is ignored. Table 23-63. RDR0AD1 Field Descriptions Field Description 7-0 Reduced Drive Port AD1 Register 0 RDR0AD1[23:16] 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. MC9S12XDP512 Data Sheet, Rev. 2.21 960 Freescale Semiconductor 23.0.5.71 Port AD1 Reduced Drive Register 1 (RDR1AD1) 7 6 5 4 3 2 1 0 R RDR1AD115 RDR1AD114 RDR1AD113 RDR1AD112 RDR1AD111 RDR1AD110 RDR1AD19 RDR1AD18 W Reset 0 0 0 0 0 0 0 0 Figure 23-73. Port AD1 Reduced Drive Register 1 (RDR1AD1) Read: Anytime. Write: Anytime. This register configures the drive strength of each PAD[15:8] output pin as either full or reduced. If the port is used as input this bit is ignored. Table 23-64. RDR1AD1 Field Descriptions Field Description 7-0 RDR1AD1[15:8] Reduced Drive Port AD1 Register 1 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 23.0.5.72 Port AD1 Pull Up Enable Register 0 (PER0AD1) 7 6 5 4 3 2 1 0 R PER0AD123 PER0AD122 PER0AD121 PER0AD120 PER0AD119 PER0AD118 PER0AD117 PER0AD116 W Reset 0 0 0 0 0 0 0 0 Figure 23-74. Port AD1 Pull Up Enable Register 0 (PER0AD1) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective PAD[23:16] pin if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull-up device is enabled. Table 23-65. PER0AD1 Field Descriptions Field 7-0 Pull Device Enable Port AD1 Register 0 PER0AD1[23:16] 0 Pull-up device is disabled. 1 Pull-up device is enabled. Description Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.5.73 Port AD1 Pull Up Enable Register 1 (PER1AD1) 7 6 5 4 3 2 1 0 PER1AD19 PER1AD18 0 0 R PER1AD115 PER1AD114 PER1AD113 PER1AD112 PER1AD111 PER1AD110 W Reset 0 0 0 0 0 0 Figure 23-75. Port AD1 Pull Up Enable Register 1 (PER1AD1) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective PAD[15:8] pin if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull-up device is enabled. Table 23-66. PER1AD1 Field Descriptions Field Description 7-0 PER1AD1[15:8] Pull Device Enable Port AD1 Register 1 0 Pull-up device is disabled. 1 Pull-up device is enabled. Functional Description Each pin except PE0, PE1, and BKGD can act as general purpose I/O. In addition each pin can act as an output from the external bus interface module or a peripheral module or an input to the external bus interface module or a peripheral module. A set of configuration registers is common to all ports with exceptions in the expanded bus interface and ATD ports (Table 23-67). All registers can be written at any time; however a specific configuration might not become active. Example: Selecting a pull-up device This device does not become active while the port is used as a push-pull output. Table 23-67. Register Availability per Port1 Port Data Data Direction Input Reduced Drive Pull Enable Polarity Select Wired-OR Mode Interrupt Enable Interrupt Flag A yes yes -- yes yes -- -- -- -- B yes yes -- -- -- -- -- C yes yes -- -- -- -- -- D yes yes -- -- -- -- -- E yes yes -- -- -- -- -- K yes yes -- -- -- -- -- T yes yes yes yes yes -- -- -- -- S yes yes yes yes yes yes yes -- -- M yes yes yes yes yes yes yes -- -- MC9S12XDP512 Data Sheet, Rev. 2.21 962 Freescale Semiconductor Table 23-67. Register Availability per Port1 Port Data Data Direction Input Reduced Drive Pull Enable Polarity Select Wired-OR Mode Interrupt Enable Interrupt Flag P yes yes yes yes yes yes -- yes yes H yes yes yes yes yes yes -- yes yes J yes yes yes yes yes yes -- yes yes AD0 yes yes -- yes yes -- -- -- -- AD1 yes yes -- yes yes -- -- -- -- 1. Each cell represents one register with individual configuration bits 23.0.6 23.0.6.1 Registers Data Register This register holds the value driven out to the pin if the pin is used as a general purpose I/O. Writing to this register has only an effect on the pin if the pin is used as general purpose output. When reading this address, the buffered state of the pin is returned if the associated data direction register bit is set to "0". If the data direction register bits are set to logic level "1", the contents of the data register is returned. This is independent of any other configuration (Figure 23-76). 23.0.6.2 Input Register This is a read-only register and always returns the buffered state of the pin (Figure 23-76). 23.0.6.3 Data Direction Register This register defines whether the pin is used as an input or an output. If a peripheral module controls the pin the contents of the data direction register is ignored (Figure 23-76). Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) PTI 0 1 PT 0 PIN 1 DDR 0 1 data out Module output enable module enable Figure 23-76. Illustration of I/O Pin Functionality 23.0.6.4 Reduced Drive Register If the pin is used as an output this register allows the configuration of the drive strength. 23.0.6.5 Pull Device Enable Register This register turns on a pull-up or pull-down device. It becomes active only if the pin is used as an input or as a wired-OR output. 23.0.6.6 Polarity Select Register This register selects either a pull-up or pull-down device if enabled. It becomes active only if the pin is used as an input. A pull-up device can be activated if the pin is used as a wired-OR output. If the pin is used as an interrupt input this register selects the active interrupt edge. 23.0.6.7 Wired-OR Mode Register If the pin is used as an output this register turns off the active high drive. This allows wired-OR type connections of outputs. 23.0.6.8 Interrupt Enable Register If the pin is used as an interrupt input this register serves as a mask to the interrupt flag to enable/disable the interrupt. 23.0.6.9 Interrupt Flag Register If the pin is used as an interrupt input this register holds the interrupt flag after a valid pin event. MC9S12XDP512 Data Sheet, Rev. 2.21 964 Freescale Semiconductor 23.0.6.10 Module Routing Register This register supports the re-routing of the CAN0, CAN4, SPI0, SPI1, and SPI2 pins to alternative ports. This allows a software re-configuration of the pinouts of the different package options with respect to above peripherals. NOTE The purpose of the module routing register is to provide maximum flexibility for derivatives with a lower number of MSCAN and SPI modules. Table 23-68. Module Implementations on Derivatives MSCAN Modules SPI Modules Number of Modules CAN0 CAN1 CAN2 CAN3 CAN4 SPI0 SPI1 SPI2 5 yes yes yes yes yes -- -- -- 4 yes yes yes -- yes -- -- -- 3 yes yes -- -- yes yes yes yes 2 yes -- -- -- yes yes yes -- 1 yes -- -- -- -- yes -- -- 23.0.7 23.0.7.1 Ports BKGD Pin The BKGD pin is associated with the S12X_BDM and S12X_EBI modules. During reset, the BKGD pin is used as MODC input. 23.0.7.2 Port A and B Port A pins PA[7:0] and Port B pins PB[7:0] can be used for either general-purpose I/O, or, in 144pin packages, also with the external bus interface. In this case port A and port B are associated with the external address bus outputs ADDR15-ADDR8 and ADDR7-ADDR0, respectively. PB0 is the ADDR0 or UDS output. 23.0.7.3 Port C and D Port C pins PC[7:0] and port D pins PD[7:0] can be used for either general-purpose I/O, or, in 144pin packages, also with the external bus interface. In this case port C and port D are associated with the external data bus inputs/outputs DATA15-DATA8 and DATA7-DATA0, respectively. These pins are configured for reduced input threshold in certain operating modes (refer to S12X_EBI section). NOTE Port C and D are neither available in 112-pin nor in 80-pin packages. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) 23.0.7.4 Port E Port E is associated with the external bus control outputs R/W, LSTRB, LDS and RE, the free-running clock outputs ECLK and ECLK2X, as well as with the TAGHI, TAGLO, MODA and MODB and interrupt inputs IRQ and XIRQ. Port E pins PE[7:2] can be used for either general-purpose I/O or with the alternative functions. Port E pin PE[7] an be used for either general-purpose I/O or as the free-running clock ECLKX2 output running at the core clock rate. The clock output is always enabled in emulation modes. Port E pin PE[4] an be used for either general-purpose I/O or as the free-running clock ECLK output running at the bus clock rate or at the programmed divided clock rate. The clock output is always enabled in emulation modes. Port E pin PE[1] can be used for either general-purpose input or as the level- or falling edge-sensitive IRQ interrupt input. IRQ will be enabled by setting the IRQEN configuration bit (Section 23.0.5.14, "IRQ Control Register (IRQCR)") and clearing the I-bit in the CPU's condition code register. It is inhibited at reset so this pin is initially configured as a simple input with a pull-up. Port E pin PE[0] can be used for either general-purpose input or as the level-sensitive XIRQ interrupt input. XIRQ can be enabled by clearing the X-bit in the CPU's condition code register. It is inhibited at reset so this pin is initially configured as a high-impedance input with a pull-up. Port E pins PE[5] and PE[6] are configured for reduced input threshold in certain modes (refer to S12X_EBI section). 23.0.7.5 Port K Port K pins PK[7:0] can be used for either general-purpose I/O, or, in 144-pin packages, also with the external bus interface. In this case port K pins PK[6:0] are associated with the external address bus outputs ADDR22-ADDR16 and PK7 is associated to the EWAIT input. Port K pin PE[7] is configured for reduced input threshold in certain modes (refer to S12X_EBI section). NOTE Port K is not available in 80-pin packages. PK[6] is not available in 112-pin packages. 23.0.7.6 Port T This port is associated with the ECT module. Port T pins PT[7:0] can be used for either general-purpose I/O, or with the channels of the enhanced capture timer. 23.0.7.7 Port S This port is associated with SCI0, SCI1 and SPI0. Port S pins PS[7:0] can be used either for generalpurpose I/O, or with the SCI and SPI subsystems. The SPI0 pins can be re-routed. Refer to Section 23.0.5.37, "Module Routing Register (MODRR)". MC9S12XDP512 Data Sheet, Rev. 2.21 966 Freescale Semiconductor NOTE PS[7:4] are not available in 80-pin packages. 23.0.7.8 Port M This port is associated with the CAN40 and SPI0. Port M pins PM[7:0] can be used for either general purpose I/O, or with the CAN, SCI and SPI subsystems. The CAN0, CAN4 and SPI0 pins can be re-routed. Refer to Section 23.0.5.37, "Module Routing Register (MODRR)". NOTE PM[7:6] are not available in 80-pin packages. 23.0.7.9 Port P This port is associated with the PWM, SPI1 and SPI2. Port P pins PP[7:0] can be used for either general purpose I/O, or with the PWM and SPI subsystems. The pins are shared between the PWM channels and the SPI1 and SPI2. If the PWM is enabled the pins become PWM output channels with the exception of pin 7 which can be PWM input or output. If SPI1 or SPI2 are enabled and PWM is disabled, the respective pin configuration is determined by status bits in the SPI. The SPI1 and SPI2 pins can be re-routed. Refer to Section 23.0.5.37, "Module Routing Register (MODRR)". Port P offers 8 I/O pins with edge triggered interrupt capability in wired-OR fashion (Section 23.0.8, "Pin Interrupts"). NOTE PP[6] is not available in 80-pin packages. 23.0.7.10 Port H This port is associated with the SPI1, SPI2, SCI4. Port H pins PH[7:0] can be used for either general purpose I/O, or with the SPI and SCI subsystems. Port H pins can be used with the routed SPI1 and SPI2. Refer to Section 23.0.5.37, "Module Routing Register (MODRR)". Port H offers 8 I/O pins with edge triggered interrupt capability (Section 23.0.8, "Pin Interrupts"). NOTE Port H is not available in 80-pin packages. 23.0.7.11 Port J This port is associated with the chip selects CS0, CS1, CS2 and CS3 as well as with CAN4, CAN0, IIC1, IIC0, and SCI2. Port J pins PJ[7:4] and PJ[2:0] can be used for either general purpose I/O, or with the CAN, IIC, or SCI subsystems. If IIC takes precedence the associated pins become IIC Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) open-drain output pins. The CAN4 pins can be re-routed. Refer to Section 23.0.5.37, "Module Routing Register (MODRR)". Port J pins can be used with the routed CAN0 modules. Refer to Section 23.0.5.37, "Module Routing Register (MODRR)". Port J offers 7 I/O pins with edge triggered interrupt capability (Section 23.0.8, "Pin Interrupts"). NOTE PJ[5,4,2] are not available in 112-pin packages. PJ[5,4,2,1,0] are not available in 80-pin packages. 23.0.7.12 Port AD0 This port is associated with the ATD0. Port AD0 pins PAD07-PAD00 can be used for either general purpose I/O, or with the ATD0 subsystem. 23.0.7.13 Port AD1 This port is associated with the ATD1. Port AD1 pins PAD23-PAD8 can be used for either general purpose I/O, or with the ATD1 subsystem. NOTE PAD[23:16] are not available in 112-pin packages. PAD[23:8] are not available in 80-pin packages. 23.0.8 Pin Interrupts Ports P, H and J offer pin interrupt capability. The interrupt enable as well as the sensitivity to rising or falling edges can be individually configured on per-pin basis. All bits/pins in a port share the same interrupt vector. Interrupts can be used with the pins configured as inputs or outputs. An interrupt is generated when a bit in the port interrupt flag register and its corresponding port interrupt enable bit are both set. The pin interrupt feature is also capable to wake up the CPU when it is in STOP or WAIT mode. A digital filter on each pin prevents pulses (Figure 23-78) shorter than a specified time from generating an interrupt. The minimum time varies over process conditions, temperature and voltage (Figure 23-77 and Table 23-69). MC9S12XDP512 Data Sheet, Rev. 2.21 968 Freescale Semiconductor Glitch, filtered out, no interrupt flag set Valid pulse, interrupt flag set uncertain tpign tpval Figure 23-77. Interrupt Glitch Filter on Port P, H, and J (PPS = 0) Table 23-69. Pulse Detection Criteria Mode Pulse STOP Unit STOP1 Ignored tpulse 3 Bus clocks tpulse tpign Uncertain 3 < tpulse < 4 Bus clocks tpign < tpulse < tpval Valid tpulse 4 Bus clocks tpulse tpval 1. These values include the spread of the oscillator frequency over temperature, voltage and process. tpulse Figure 23-78. Pulse Illustration A valid edge on an input is detected if 4 consecutive samples of a passive level are followed by 4 consecutive samples of an active level directly or indirectly. The filters are continuously clocked by the bus clock in run and wait mode. In stop mode, the clock is generated by an RC-oscillator in the port integration module. To maximize current saving the RC oscillator runs only if the following condition is true on any pin individually: Sample count <= 4 and interrupt enabled (PIE = 1) and interrupt flag not set (PIF = 0). 23.0.9 Expanded Bus Pin Functions All peripheral ports T, S, M, P, H, J, AD0, and AD1 start up as general purpose inputs after reset. Depending on the external mode pin condition, the external bus interface related ports A, B, C, D, E, and K start up as general purpose inputs on reset or are configured for their alternate functions. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) Table 23-70 lists the pin functions in relationship with the different operating modes. If two entries per pin are displayed, a `mux' indicates time-multiplexing between the two functions and an `or' means that a configuration bit exists which can be altered after reset to select the respective function (displayed in italics). Refer to S12X_EBI section for details. Table 23-70. Expanded Bus Pin Functions versus Operating Modes Single-Chip Modes Expanded Modes Pin Normal SingleChip Special SingleChip Normal Expanded Emulation Single-Chip Emulation Expanded Special Test PK7 GPIO GPIO GPIO or EWAIT GPIO GPIO or EWAIT GPIO PK[6:4] GPIO GPIO ADDR[22:20] or GPIO ADDR[22:20] mux ACC[2:0] ADDR[22:20] mux ACC[2:0] ADDR[22:20] PK[3:0] GPIO GPIO ADDR[19:16] or GPIO ADDR[19:16] mux IQSTAT[3:0] ADDR[19:16] mux IQSTAT[3:0] ADDR[19:16] PA[7:0] GPIO GPIO ADDR[15:8] or GPIO ADDR[15:8] mux IVD[15:8] ADDR[15:8] mux IVD[15:8] ADDR[15:8] PB[7:1] GPIO GPIO ADDR[7:1] or GPIO ADDR[7:1] mux IVD[7:1] ADDR[7:1] mux IVD[7:1] ADDR[7:1] PB0 GPIO GPIO UDS or GPIO ADDR0 mux IVD0 ADDR0 mux IVD0 ADDR0 PC[7:0] GPIO GPIO DATA[15:8] or GPIO DATA[15:8] DATA[15:8] DATA[15:8] or GPIO PD[7:0] GPIO GPIO DATA[7:0] DATA[7:0] DATA[7:0] DATA[7:0] PE7 GPIO or ECLKX2 GPIO or ECLKX2 GPIO or ECLKX2 ECLKX2 ECLKX2 GPIO or ECLKX2 PE6 GPIO GPIO GPIO TAGHI TAGHI GPIO PE5 GPIO GPIO RE TAGLO TAGLO GPIO PE4 GPIO or ECLK ECLK or GPIO ECLK or GPIO ECLK ECLK ECLK or GPIO PE3 GPIO GPIO LDS or GPIO LSTRB LSTRB LSTRB PE2 GPIO GPIO WE R/W R/W R/W PJ5 GPIO GPIO GPIO or CS2 GPIO GPIO or CS2 GPIO or CS2 PJ4 GPIO GPIO GPIO or CS0 (1) GPIO GPIO or CS0 (1) GPIO or CS0 MC9S12XDP512 Data Sheet, Rev. 2.21 970 Freescale Semiconductor Table 23-70. Expanded Bus Pin Functions versus Operating Modes (continued) Single-Chip Modes Expanded Modes Pin Normal SingleChip Special SingleChip Normal Expanded Emulation Single-Chip Emulation Expanded Special Test PJ2 GPIO GPIO GPIO or CS1 GPIO GPIO or CS1 GPIO or CS1 PJ0 GPIO GPIO GPIO or CS3 GPIO GPIO or CS3 GPIO or CS3 1. Depending on ROMON bit. Refer to Device Guide, S12X_EBI section and S12X_MMC section for details. 23.0.10 Low-Power Options 23.0.10.1 Run Mode No low-power options exist for this module in run mode. 23.0.10.2 Wait Mode No low-power options exist for this module in wait mode. 23.0.10.3 Stop Mode All clocks are stopped. There are asynchronous paths to generate interrupts from stop on port P, H, and J. Initialization and Application Information * It is not recommended to write PORTx and DDRx in a word access. When changing the register pins from inputs to outputs, the data may have extra transitions during the write access. Initialize the port data register before enabling the outputs. * Power consumption will increase the more the voltages on general purpose input pins deviate from the supply voltages towards mid-range because the digital input buffers operate in the linear region. Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 972 Freescale Semiconductor Chapter 23 DQ256 Port Integration Module (S12XDQ256PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 974 Freescale Semiconductor Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Introduction The S12XD family port integration module (below referred to as PIM) establishes the interface between the peripheral modules including the non-multiplexed external bus interface module (S12X_EBI) and the I/O pins for all ports. It controls the electrical pin properties as well as the signal prioritization and multiplexing on shared pins. This document covers the description of: * Port A, B * Port E associated with the IRQ, XIRQ interrupt inputs * Port K * Port T connected to the Enhanced Capture Timer (ECT) module * Port S associated with 2 SCI and 1 SPI modules * Port M associated with 2 MSCAN modules and 1 SCI module * Port P connected to the PWM and 1 SPI module -- inputs can be used as an external interrupt source * Port H associated with 2 SCI modules -- inputs can be used as an external interrupt source * Port J associated with 1 MSCAN, 1 SCI, and 1 IIC module -- inputs can be used as an external interrupt source * Port AD1 associated with one 16-channel ATD module Most I/O pins can be configured by register bits to select data direction and drive strength, to enable and select pull-up or pull-down devices. Interrupts can be enabled on specific pins resulting in status flags. The I/O's of 2 MSCAN and 2 SPI modules can be routed from their default location to alternative port pins. NOTE The implementation of the PIM is device dependent. Therefore some functions are not available on certain derivatives or80-pin package options. 24.0.1 Features A full-featured PIM module includes these distinctive registers: MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 975 Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) * * * * * * * * * * * Data and data direction registers for Ports A, B, E, K, T, S, M, P, H, J, and AD1 when used as general-purpose I/O Control registers to enable/disable pull-device and select pull-ups/pull-downs on Ports T, S, M, P, H, and J on per-pin basis Control registers to enable/disable pull-up devices on Port AD1 on per-pin basis Single control register to enable/disable pull-ups on Ports A, B, E, and K on per-port basis and on BKGD pin Control registers to enable/disable reduced output drive on Ports T, S, M, P, H, J, and AD1 on perpin basis Single control register to enable/disable reduced output drive on Ports A, B, E, and K on per-port basis Control registers to enable/disable open-drain (wired-OR) mode on Ports S and M Control registers to enable/disable pin interrupts on Ports P, H, and J Interrupt flag register for pin interrupts on Ports P, H, and J Control register to configure IRQ pin operation Free-running clock outputs A standard port pin has the following minimum features: * Input/output selection * 5V output drive with two selectable drive strengths * 5V digital and analog input * Input with selectable pull-up or pull-down device Optional features: * Open drain for wired-OR connections * Interrupt inputs with glitch filtering * Reduced input threshold to support low voltage applications 24.0.2 Block Diagram Figure 24-1 is a block diagram of the PIM. * Signals shown in Bold are not available in 80-pin packages. * Shaded labels denote alternative module routing ports. MC9S12XDP512 Data Sheet, Rev. 2.21 976 Freescale Semiconductor MOSI MISO Port AD1 SS SPI1 SCK Port T PWM IOC7 IOC6 IOC5 IOC4 IOC3 IOC2 IOC1 IOC0 PAD15 PAD14 PAD13 PAD12 PAD11 PAD10 PAD09 PAD08 PAD07 PAD06 PAD05 PAD04 PAD03 PAD02 PAD01 PAD00 PT7 PT6 PT5 PT4 PT3 PT2 PT1 PT0 Port P ECT SPI0 CAN0 CAN0 CAN4 CAN4 PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 AN15 AN14 AN13 AN12 AN11 AN10 AN9 AN8 AN7 AN6 AN5 AN4 AN3 AN2 AN1 AN0 Interrupt Logic ATD1 TXCAN CAN4 RXCAN SCL IIC0 SDA TXCAN CAN0 RXCAN Port A PP7 PP6 PP5 PP4 PP3 PP2 PP1 PP0 PS7 PS6 PS5 PS4 PS3 PS2 PS1 PS0 SS SPI0 SCK MOSI MISO TXD SCI1 RXD TXD SCI0 RXD BKGD/MODC XCLKS S12X_BDM S12X_INT S12X_MMC ECLKX2 ECLK Port E Port B IRQ XIRQ Figure 24-1. PIM_9XDG128 Block Diagram BKGD PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 PK7 ROMCTL Port K PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 Port M PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 Interrupt Logic Port J PJ1 PJ0 Interrupt Logic CAN0 PJ6 PM7 PM6 PM5 PM4 PM3 PM2 PM1 PM0 SPI1 PJ7 SPI2 Port H PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 Port S Port Integration Module PK5 PK4 PK3 PK2 PK1 PK0 Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) External Signal Description This section lists and describes the signals that do connect off-chip. 24.0.3 Signal Properties Table 24-1 shows all the pins and their functions that are controlled by the PIM. Refer to Section , "Functional Description" for the availability of the individual pins in the different package options. NOTE If there is more than one function associated with a pin, the priority is indicated by the position in the table from top (highest priority) to bottom (lowest priority). Table 24-1. Pin Functions and Priorities (Sheet 1 of 5) Port Pin Name Pin Function and Priority I/O -- BKGD MODC1 I BKGD I/O S12X_BDM communication pin Pin Function after Reset Description MODC input during RESET BKGD A PA[7:0] GPIO I/O General-purpose I/O GPIO B PB[7:0] GPIO I/O General-purpose I/O GPIO XCLKS1 I External clock selection input during RESET ECLKX2 I Free-running clock output at Core Clock rate (ECLK x 2) GPIO I/O General-purpose I/O GPIO I/O General-purpose I/O ECLK O Free-running clock output at the Bus Clock rate or programmable divided in normal modes GPIO I/O General-purpose I/O GPIO I/O General-purpose I/O IRQ I GPIO I/O XIRQ I GPIO I/O General-purpose I/O PK[7] GPIO I/O General-purpose I/O PK[5:0] GPIO I/O General-purpose I/O IOC[7:0] I/O Enhanced Capture Timer Channels 7-0 input/output GPIO I/O General-purpose I/O PE[7] PE[6:5] E PE[4] PE[3:2] Maskable level- or falling edge-sensitive interrupt input PE[1] General-purpose I/O Non-maskable level-sensitive interrupt input PE[0] K T GPIO PT[7:0] GPIO MC9S12XDP512 Data Sheet, Rev. 2.21 978 Freescale Semiconductor Table 24-1. Pin Functions and Priorities (Sheet 2 of 5) Port Pin Name Pin Function and Priority I/O SS0 I/O Serial Peripheral Interface 0 slave select output in master mode, input in slave mode or master mode. GPIO I/O General-purpose I/O SCK0 I/O Serial Peripheral Interface 0 serial clock pin GPIO I/O General-purpose I/O MOSI0 I/O Serial Peripheral Interface 0 master out/slave in pin GPIO I/O General-purpose I/O MISO0 I/O Serial Peripheral Interface 0 master in/slave out pin GPIO I/O General-purpose I/O TXD1 O Serial Communication Interface 1 transmit pin GPIO I/O General-purpose I/O RXD1 I GPIO I/O General-purpose I/O TXD0 O Serial Communication Interface 0 transmit pin GPIO I/O General-purpose I/O RXD0 I GPIO I/O PS7 Description Pin Function after Reset PS6 PS5 PS4 S PS3 Serial Communication Interface 1 receive pin PS2 PS1 Serial Communication Interface 0 receive pin PS0 General-purpose I/O GPIO Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-1. Pin Functions and Priorities (Sheet 3 of 5) Port Pin Name Pin Function and Priority I/O Pin Function after Reset TXCAN4 O MSCAN4 transmit pin GPIO I/O General-purpose I/O RXCAN4 I MSCAN4 receive pin GPIO I/O General-purpose I/O TXCAN0 O MSCAN0 transmit pin TXCAN4 O MSCAN4 transmit pin SCK0 I/O Serial Peripheral Interface 0 serial clock pin If CAN0 is routed to PM[3:2] the SPI0 can still be used in bidirectional master mode. GPIO I/O General-purpose I/O RXCAN0 I MSCAN0 receive pin RXCAN4 I MSCAN4 receive pin MOSI0 I/O Serial Peripheral Interface 0 master out/slave in pin If CAN0 is routed to PM[3:2] the SPI0 can still be used in bidirectional master mode. GPIO I/O General-purpose I/O TXCAN0 O MSCAN0 transmit pin SS0 I/O Serial Peripheral Interface 0 slave select output in master mode, input for slave mode or master mode. GPIO I/O General-purpose I/O RXCAN0 I MSCAN0 receive pin MISO0 I/O Serial Peripheral Interface 0 master in/slave out pin GPIO I/O General-purpose I/O TXCAN0 O MSCAN0 transmit pin GPIO I/O General-purpose I/O RXCAN0 I MSCAN0 receive pin GPIO I/O General-purpose I/O Description PM7 PM6 PM5 PM4 M PM3 PM2 GPIO PM1 PM0 MC9S12XDP512 Data Sheet, Rev. 2.21 980 Freescale Semiconductor Table 24-1. Pin Functions and Priorities (Sheet 4 of 5) Port Pin Name Pin Function and Priority I/O PWM7 I/O Pulse Width Modulator input/output channel 7 GPIO/KWP7 I/O General-purpose I/O with interrupt PWM6 O Pulse Width Modulator output channel 6 GPIO/KWP6 I/O General-purpose I/O with interrupt PWM5 O Pulse Width Modulator output channel 5 GPIO/KWP5 I/O General-purpose I/O with interrupt PWM4 O Pulse Width Modulator output channel 4 GPIO/KWP4 I/O General-purpose I/O with interrupt PWM3 O Pulse Width Modulator output channel 3 SS1 I/O Serial Peripheral Interface 1 slave select output in master mode, input for slave mode or master mode. Description Pin Function after Reset PP7 PP6 PP5 PP4 PP3 P PP2 PP1 PP0 GPIO/KWP3 I/O General-purpose I/O with interrupt PWM2 O Pulse Width Modulator output channel 2 SCK1 I/O Serial Peripheral Interface 1 serial clock pin GPIO/KWP2 I/O General-purpose I/O with interrupt PWM1 O Pulse Width Modulator output channel 1 MOSI1 I/O Serial Peripheral Interface 1 master out/slave in pin GPIO/KWP1 I/O General-purpose I/O with interrupt PWM0 O Pulse Width Modulator output channel 0 MISO1 I/O Serial Peripheral Interface 1 master in/slave out pin GPIO/KWP0 I/O General-purpose I/O with interrupt GPIO Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-1. Pin Functions and Priorities (Sheet 5 of 5) Port Pin Function and Priority I/O SS2 I/O Serial Peripheral Interface 2 slave select output in master mode, input for slave mode or master mode TXD5 O Serial Communication Interface 5 transmit pin GPIO/KWH7 I/O General-purpose I/O with interrupt SCK2 I/O Serial Peripheral Interface 2 serial clock pin RXD5 I GPIO/KWH6 I/O General-purpose I/O with interrupt MOSI2 I/O Serial Peripheral Interface 2 master out/slave in pin TXD4 O Serial Communication Interface 4 transmit pin GPIO/KWH5 I/O General-purpose I/O with interrupt MISO2 I/O Serial Peripheral Interface 2 master in/slave out pin RXD4 I GPIO/KWH4 I/O General-purpose I/O with interrupt SS1 I/O Serial Peripheral Interface 1 slave select output in master mode, input for slave mode or master mode. GPIO/KWH3 I/O General-purpose I/O with interrupt SCK1 I/O Serial Peripheral Interface 1 serial clock pin GPIO/KWH2 I/O General-purpose I/O with interrupt MOSI1 I/O Serial Peripheral Interface 1 master out/slave in pin GPIO/KWH1 I/O General-purpose I/O with interrupt MISO1 I/O Serial Peripheral Interface 1 master in/slave out pin GPIO/KWH0 I/O General-purpose I/O with interrupt TXCAN4 O MSCAN4 transmit pin SCL0 O Inter Integrated Circuit 0 serial clock line TXCAN0 O MSCAN0 transmit pin GPIO/KWJ7 I/O General-purpose I/O with interrupt RXCAN4 I SDA0 I/O RXCAN0 I GPIO/KWJ6 I/O General-purpose I/O with interrupt PJ1 GPIO/KWJ1 I/O General-purpose I/O with interrupt PJ0 GPIO/KWJ0 I/O General-purpose I/O with interrupt GPIO I/O General-purpose I/O AN[15:0] I ATD1 analog inputs Pin Name PH7 PH6 PH5 Pin Function after Reset Description Serial Communication Interface 5 receive pin H GPIO PH4 PH3 Serial Communication Interface 4 receive pin PH2 PH1 PH0 PJ7 MSCAN4 receive pin J GPIO Inter Integrated Circuit 0 serial data line PJ6 AD1 MSCAN0 receive pin PAD[15:00] GPIO 1. Function active when RESET asserted. MC9S12XDP512 Data Sheet, Rev. 2.21 982 Freescale Semiconductor Memory Map and Register Definition This section provides a detailed description of all PIM registers. 24.0.4 Module Memory Map Table 24-2 shows the register map of the port integration module. Table 24-2. PIM Memory Map (Sheet 1 of 3) Address Use Access 0x0000 Port A Data Register (PORTA) Read / Write 0x0001 Port B Data Register (PORTB) Read / Write 0x0002 Port A Data Direction Register (DDRA) Read / Write 0x0003 Port B Data Direction Register (DDRB) Read / Write 0x0004 : 0x0007 PIM Reserved 0x0008 Port E Data Register (PORTE) Read / Write1 0x0009 Port E Data Direction Register (DDRE) Read / Write1 0x000A : 0x000B Non-PIM Address Range 0x000C Pull-up Up Control Register (PUCR) Read / Write1 0x000D Reduced Drive Register (RDRIV) Read / Write1 0x000E : 0x001B Non-PIM Address Range 0x001C ECLK Control Register (ECLKCTL) 0x001D PIM Reserved 0x001E IRQ Control Register (IRQCR) 0x001F PIM Reserved -- 0x0020 : 0x0031 Non-PIM Address Range -- 0x0032 Port K Data Register (PORTK) Read / Write 0x0033 Port K Data Direction Register (DDRK) Read / Write 0x0034 : 0x023F Non-PIM Address Range 0x0240 Port T Data Register (PTT) Read / Write 0x0241 Port T Input Register (PTIT) Read 0x0242 Port T Data Direction Register (DDRT) Read / Write 0x0243 Port T Reduced Drive Register (RDRT) Read / Write -- -- -- Read / Write1 -- Read / Write1 -- Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-2. PIM Memory Map (Sheet 2 of 3) Address Use Access 0x0244 Port T Pull Device Enable Register (PERT) Read / Write 0x0245 Port T Polarity Select Register (PPST) Read / Write 0x0246 PIM Reserved -- 0x0247 PIM Reserved -- 0x0248 Port S Data Register (PTS) Read / Write 0x0249 Port S Input Register (PTIS) Read 0x024A Port S Data Direction Register (DDRS) Read / Write 0x024B Port S Reduced Drive Register (RDRS) Read / Write 0x024C Port S Pull Device Enable Register (PERS) Read / Write 0x024D Port S Polarity Select Register (PPSS) Read / Write 0x024E Port S Wired-OR Mode Register (WOMS) Read / Write 0x024F PIM Reserved 0x0250 Port M Data Register (PTM) Read / Write 0x0251 Port M Input Register (PTIM) Read 0x0252 Port M Data Direction Register (DDRM) Read / Write 0x0253 Port M Reduced Drive Register (RDRM) Read / Write 0x0254 Port M Pull Device Enable Register (PERM) Read / Write 0x0255 Port M Polarity Select Register (PPSM) Read / Write 0x0256 Port M Wired-OR Mode Register (WOMM) Read / Write 0x0257 Module Routing Register (MODRR) Read / Write 0x0258 Port P Data Register (PTP) Read / Write 0x0259 Port P Input Register (PTIP) Read 0x025A Port P Data Direction Register (DDRP) Read / Write 0x025B Port P Reduced Drive Register (RDRP) Read / Write 0x025C Port P Pull Device Enable Register (PERP) Read / Write 0x025D Port P Polarity Select Register (PPSP) Read / Write 0x025E Port P Interrupt Enable Register (PIEP) Read / Write 0x025F Port P Interrupt Flag Register (PIFP) Read / Write 0x0260 Port H Data Register (PTH) Read / Write 0x0261 Port H Input Register (PTIH) Read 0x0262 Port H Data Direction Register (DDRH) Read / Write 0x0263 Port H Reduced Drive Register (RDRH) Read / Write 0x0264 Port H Pull Device Enable Register (PERH) Read / Write 0x0265 Port H Polarity Select Register (PPSH) Read / Write 0x0266 Port H Interrupt Enable Register (PIEH) Read / Write -- MC9S12XDP512 Data Sheet, Rev. 2.21 984 Freescale Semiconductor Table 24-2. PIM Memory Map (Sheet 3 of 3) Address Use Access 0x0267 Port H Interrupt Flag Register (PIFH) Read / Write 0x0268 Port J Data Register (PTJ) Read / Write1 0x0269 Port J Input Register (PTIJ) Read 0x026A Port J Data Direction Register (DDRJ) Read / Write1 0x026B Port J Reduced Drive Register (RDRJ) Read / Write1 0x026C Port J Pull Device Enable Register (PERJ) Read / Write1 0x026D Port J Polarity Select Register (PPSJ) Read / Write1 0x026E Port J Interrupt Enable Register (PIEJ) Read / Write1 0x026F Port J Interrupt Flag Register (PIFJ) Read / Write1 0x0270 : 0x0277 PIM Reserved 0x0278 Port AD1 Data Register 0 (PT0AD1) Read / Write 0x0279 Port AD1 Data Register 1 (PT1AD1) Read / Write 0x027A Port AD1 Data Direction Register 0 (DDR0AD1) Read / Write 0x027B Port AD1 Data Direction Register 1 (DDR1AD1) Read / Write 0x027C Port AD1 Reduced Drive Register 0 (RDR0AD1) Read / Write 0x027D Port AD1 Reduced Drive Register 1 (RDR1AD1) Read / Write 0x027E Port AD1 Pull Up Enable Register 0 (PER0AD1) Read / Write 0x027F Port AD1 Pull Up Enable Register 1 (PER1AD1) Read / Write -- 1. Write access not applicable for one or more register bits. Refer to Section 24.0.5, "Register Descriptions". 24.0.5 Register Descriptions Table 24-3 summarizes the effect on the various configuration bits, data direction (DDR), output level (IO), reduced drive (RDR), pull enable (PE), pull select (PS), and interrupt enable (IE) for the ports. The configuration bit PS is used for two purposes: 1. Configure the sensitive interrupt edge (rising or falling), if interrupt is enabled. 2. Select either a pull-up or pull-down device if PE is active. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-3. Pin Configuration Summary DDR IO RDR PE PS1 IE2 0 x x 0 x 0 Input Disabled Disabled 0 x x 1 0 0 Input Pull Up Disabled 0 x x 1 1 0 Input Pull Down Disabled 0 x x 0 0 1 Input Disabled Falling edge 0 x x 0 1 1 Input Disabled Rising edge 0 x x 1 0 1 Input Pull Up Falling edge 0 x x 1 1 1 Input Pull Down Rising edge 1 0 0 x x 0 Output, full drive to 0 Disabled Disabled 1 1 0 x x 0 Output, full drive to 1 Disabled Disabled 1 0 1 x x 0 Output, reduced drive to 0 Disabled Disabled 1 1 1 x x 0 Output, reduced drive to 1 Disabled Disabled 1 0 0 x 0 1 Output, full drive to 0 Disabled Falling edge 1 1 0 x 1 1 Output, full drive to 1 Disabled Rising edge 1 0 1 x 0 1 Output, reduced drive to 0 Disabled Falling edge 1 1 1 x 1 1 Output, reduced drive to 1 Disabled Rising edge Function Pull Device Interrupt 1. Always "0" on Port A, B, C, D, E, K, AD0, and AD1. 2. Applicable only on Port P, H, and J. NOTE All register bits in this module are completely synchronous to internal clocks during a register read. Register Name PORTA R W PORTB R W DDRA R W DDRB R W Bit 7 6 5 4 3 2 1 Bit 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 = Unimplemented or Reserved Figure 24-2. PIM Register Summary (Sheet 1 of 7) MC9S12XDP512 Data Sheet, Rev. 2.21 986 Freescale Semiconductor Register Name Reserved R Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 0 0 W Reserved R W Reserved R W Reserved R W PORTE R W DDRE R W R Non-PIM W Address Range PUCR R W RDRIV R W Non-PIM Address Range PUPKE RDPK BKPUE 0 0 W Reserved R PUPDE1 PUPCE1 PUPBE PUPAE RDPE RDPD1 RDPC1 RDPB RDPA EDIV1 EDIV0 0 R Non-PIM W Address Range ECLKCTL R PUPEE Non-PIM Address Range NECLK NCLKX2 0 0 IRQE IRQEN 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W IRQCR R W Reserved R W = Unimplemented or Reserved Figure 24-2. PIM Register Summary (Sheet 2 of 7) Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Register Name Bit 7 6 5 Non-PIM R Address W Range PORTK R W DDRK R W R W PTIT R 3 2 1 Bit 0 Non-PIM Address Range PK7 DDRK7 0 0 PK5 PK4 PK3 PK2 PK1 PK0 DDRK5 DDRK4 DDRK3 DDRK2 DDRK1 DDRK0 Non-PIM R Address W Range PTT 4 Non-PIM Address Range PTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0 PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0 DDRT7 DDRT6 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0 RDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0 PERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0 PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0 W DDRT R W RDRT R W PERT R W PPST R W Reserved R W Reserved R W PTS R W PTIS R W = Unimplemented or Reserved Figure 24-2. PIM Register Summary (Sheet 3 of 7) MC9S12XDP512 Data Sheet, Rev. 2.21 988 Freescale Semiconductor Register Name DDRS R W RDRS R W PERS R W PPSS R W WOMS R W Reserved R Bit 7 6 5 4 3 2 1 Bit 0 DDRS7 DDRS6 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0 RDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0 PERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0 PPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0 WOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0 0 0 0 0 0 0 0 0 PTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0 PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0 DDRM7 DDRM6 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0 RDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0 PERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0 PPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0 WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 MODRR61 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0 W PTM R W PTIM R W DDRM R W RDRM R W PERM R W PPSM R W WOMM R W MODRR R 0 W PTP R W PTP7 = Unimplemented or Reserved Figure 24-2. PIM Register Summary (Sheet 4 of 7) Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Register Name PTIP R Bit 7 6 5 4 3 2 1 Bit 0 PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0 DDRP7 DDRP6 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0 RDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0 PERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0 PPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSP0 PIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0 PIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0 PTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0 PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0 DDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 RDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0 PERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0 PPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0 PIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0 PIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0 W DDRP R W RDRP R W PERP R W PPSP R W PIEP R W PIFP R W PTH R W PTIH R W DDRH R W RDRH R W PERH R W PPSH R W PIEH R W PIFH R W = Unimplemented or Reserved Figure 24-2. PIM Register Summary (Sheet 5 of 7) MC9S12XDP512 Data Sheet, Rev. 2.21 990 Freescale Semiconductor Register Name PTJ R W PTIJ R Bit 7 6 5 4 3 2 1 Bit 0 PTJ7 PTJ6 0 0 0 0 PTJ1 PTJ0 PTIJ7 PTIJ6 0 0 0 0 PTIJ1 PTIJ0 DDRJ7 DDRJ6 0 0 0 0 DDRJ1 DDRJ0 RDRJ7 RDRJ6 0 0 0 0 RDRJ1 RDRJ0 PERJ7 PERJ6 0 0 0 0 PERJ1 PERJ0 PPSJ7 PPSJ6 0 0 0 0 PPSJ1 PPSJ0 PIEJ7 PIEJ6 0 0 0 0 PIEJ1 PIEJ0 PPSJ7 PPSJ6 0 0 0 0 PPSJ1 PPSJ0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W DDRJ R W RDRJ R W PERJ R W PPSJ R W PIEJ R W PIFJ R W Reserved R W Reserved R W Reserved R W Reserved R W Reserved R W Reserved R W Reserved R W = Unimplemented or Reserved Figure 24-2. PIM Register Summary (Sheet 6 of 7) Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Register Name Reserved Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 PT1AD115 PT1AD114 PT1AD113 PT1AD112 PT1AD111 PT1AD110 PT1AD19 PT1AD18 PT1AD17 PT1AD16 PT1AD15 PT1AD14 PT1AD13 PT1AD12 PT1AD11 PT1AD10 R W PT0AD1 R W PT1AD1 R W DDR0AD1 R W DDR1AD1 R W RDR0AD1 R W RDR1AD1 R W PER0AD1 R W PER1AD1 R W DDR1AD115 DDR1AD114 DDR1AD113 DDR1AD112 DDR1AD111 DDR1AD110 DDR1AD19 DDR1AD18 DDR1AD17 DDR1AD16 DDR1AD15 DDR1AD14 DDR1AD13 DDR1AD12 DDR1AD11 DDR1AD10 RDR1AD115 RDR1AD114 RDR1AD113 RDR1AD112 RDR1AD111 RDR1AD110 RDR1AD19 RDR1AD18 RDR1AD17 RDR1AD16 RDR1AD15 RDR1AD14 RDR1AD13 RDR1AD12 RDR1AD11 RDR1AD10 PER1AD115 PER1AD114 PER1AD113 PER1AD112 PER1AD111 PER1AD110 PER1AD19 PER1AD18 PER1AD17 PER1AD10 PER1AD16 PER1AD15 PER1AD14 PER1AD13 PER1AD12 PER1AD11 = Unimplemented or Reserved Figure 24-2. PIM Register Summary (Sheet 7 of 7) 1. Register implemented, function disabled: Written values can be read back. 24.0.5.1 Port A Data Register (PORTA) 7 6 5 4 3 2 1 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 0 0 0 0 0 0 0 0 R W Reset Figure 24-3. Port A Data Register (PORTA) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 992 Freescale Semiconductor Table 24-4. PORTA Field Descriptions Field Description 7-0 PA[7:0] Port A -- Port A pins 7-0 can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 24.0.5.2 Port B Data Register (PORTB) 7 6 5 4 3 2 1 0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 0 0 0 0 0 0 0 0 R W Reset Figure 24-4. Port B Data Register (PORTB) Read: Anytime. Write: Anytime. Table 24-5. PORTB Field Descriptions Field Description 7-0 PB[7:0] Port B -- Port B pins 7-0 can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 24.0.5.3 Port A Data Direction Register (DDRA) 7 6 5 4 3 2 1 0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 0 0 0 0 0 0 0 0 R W Reset Figure 24-5. Port A Data Direction Register (DDRA) Read: Anytime. Write: Anytime. Table 24-6. DDRA Field Descriptions Field Description 7-0 DDRA[7:0] Data Direction Port A -- This register controls the data direction for port A. DDRA determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTA after changing the DDRA register. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.5.4 Port B Data Direction Register (DDRB) 7 6 5 4 3 2 1 0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 0 0 0 0 0 0 0 0 R W Reset Figure 24-6. Port B Data Direction Register (DDRB) Read: Anytime. Write: Anytime. Table 24-7. DDRB Field Descriptions Field Description 7-0 DDRB[7:0] Data Direction Port B -- This register controls the data direction for port B. DDRB determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTB after changing the DDRB register. 24.0.5.5 Port E Data Register (PORTE) 7 6 5 4 3 2 PE7 PE6 PE5 PE4 PE3 PE2 Alt. Func. XCLKS or ECLKX2 MODB MODA ECLK EROMCTL Reset 0 0 0 0 0 R 1 0 PE1 PE0 IRQ XIRQ --1 --1 W 0 = Unimplemented or Reserved Figure 24-7. Port E Data Register (PORTE) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 994 Freescale Semiconductor Table 24-8. PORTE Field Descriptions Field 7-0 PE[7:0] Description Port E -- Port E bits 7-0 are associated with external bus control signals and interrupt inputs. These include mode select (MODB, MODA), E clock, double frequency E clock, IRQ, and XIRQ. When not used for any of these specific functions, Port E pins 7-2 can be used as general purpose I/O and pins 1-0 can be used as general purpose inputs. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Pins 6 and 5 are inputs with enabled pull-down devices while RESET pin is low. Pins 7 and 3 are inputs with enabled pull-up devices while RESET pin is low. 24.0.5.6 Port E Data Direction Register (DDRE) 7 6 5 4 3 2 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 0 0 0 0 0 0 R 1 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 24-8. Port E Data Direction Register (DDRE) Read: Anytime. Write: Anytime. Table 24-9. DDRE Field Descriptions Field Description 7-0 DDRE[7:2] Data Direction Port E -- his register controls the data direction for port E. DDRE determines whether each pin is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. Port E bit 1 (associated with IRQ) and bit 0 (associated with XIRQ) cannot be configured as outputs. Port E, bits 1 and 0, can be read regardless of whether the alternate interrupt function is enabled. 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTE after changing the DDRE register. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.5.7 S12X_EBI Ports, BKGD, VREGEN Pin Pull-up Control Register (PUCR) 7 6 PUPKE BKPUE 1 1 5 R 4 3 2 1 0 PUPEE PUPDE1 PUPCE1 PUPBE PUPAE 1 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 24-9. S12X_EBI Ports, BKGD, VREGEN Pin Pull-up Control Register (PUCR) 1. Register implemented, function disabled: Written values can be read back. Read: Anytime in single-chip modes. Write: Anytime, except BKPUE which is writable in special test mode only. This register is used to enable pull-up devices for the associated ports A, B E, and K. Pull-up devices are assigned on a per-port basis and apply to any pin in the corresponding port currently configured as an input. Table 24-10. PUCR Field Descriptions Field Description 7 PUPKE Pull-up Port K Enable 0 Port K pull-up devices are disabled. 1 Enable pull-up devices for Port K input pins. 6 BKPUE BKGD and VREGEN Pin Pull-up Enable 0 BKGD and VREGEN pull-up devices are disabled. 1 Enable pull-up devices on BKGD and VREGEN pins. 4 PUPEE Pull-up Port E Enable 0 Port E pull-up devices on bit 7, 4-0 are disabled. 1 Enable pull-up devices for Port E input pins bits 7, 4-0. Note: Bits 5 and 6 of Port E have pull-down devices which are only enabled during reset. This bit has no effect on these pins. 1 PUPBE Pull-up Port B Enable 0 Port B pull-up devices are disabled. 1 Enable pull-up devices for all Port B input pins. 0 PUPAE Pull-up Port A Enable 0 Port A pull-up devices are disabled. 1 Enable pull-up devices for all Port A input pins. MC9S12XDP512 Data Sheet, Rev. 2.21 996 Freescale Semiconductor 24.0.5.8 S12X_EBI Ports Reduced Drive Register (RDRIV) 7 R 6 5 0 0 RDPK 4 3 2 1 0 RDPE RDPD1 RDPC1 RDPB RDPA 0 0 0 0 0 W Reset 0 0 0 = Unimplemented or Reserved Figure 24-10. S12X_EBI Ports Reduced Drive Register (RDRIV) 1. Register implemented, function disabled: Written values can be read back. Read: Anytime. Write: Anytime. This register is used to select reduced drive for the pins associated with ports A, B, E, and K. If enabled, the pins drive at about 1/6 of the full drive strength. The reduced drive function is independent of which function is being used on a particular pin. The reduced drive functionality does not take effect on the pins in emulation modes. Table 24-11. RDRIV Field Descriptions Field Description 7 RDPK Reduced Drive of Port K 0 All port K output pins have full drive enabled. 1 All port K output pins have reduced drive enabled. 4 RDPE Reduced Drive of Port E 0 All port E output pins have full drive enabled. 1 All port E output pins have reduced drive enabled. 1 RDPB Reduced Drive of Port B 0 All port B output pins have full drive enabled. 1 All port B output pins have reduced drive enabled. 0 RDPA Reduced Drive of Ports A 0 All Port A output pins have full drive enabled. 1 All port A output pins have reduced drive enabled. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.5.9 ECLK Control Register (ECLKCTL) 7 6 1 0 NECLK NCLKX2 EDIV1 EDIV0 Mode Dependent 1 0 0 0 0 0 0 Mode 0 1 0 0 0 0 0 0 Special Single-Chip 1 1 0 0 0 0 0 0 Emulation Single-Chip 0 1 0 0 0 0 0 0 Special Test 0 1 0 0 0 0 0 0 Emulation Expanded 1 1 0 0 0 0 0 0 Normal Single-Chip 0 1 0 0 0 0 0 0 Normal Expanded R 5 4 3 2 0 0 0 0 W Reset1 SS ES ST EX NS NX = Unimplemented or Reserved Figure 24-11. ECLK Control Register (ECLKCTL) 1. Reset values in emulation modes are identical to those of the target mode. Read: Anytime. Write: Anytime. The ECLKCTL register is used to control the availability of the free-running clocks and the free-running clock divider. Table 24-12. ECLKCTL Field Descriptions Field Description 7 NECLK No ECLK -- This bit controls the availability of a free-running clock on the ECLK pin. Clock output is always active in emulation modes and if enabled in all other operating modes. 0 ECLK enabled 1 ECLK disabled 6 NCLKX2 No ECLKX2 -- This bit controls the availability of a free-running clock on the ECLKX2 pin. This clock has a fixed rate of twice the internal bus clock. Clock output is always active in emulation modes and if enabled in all other operating modes. 0 ECLKX2 is enabled 1 ECLKX2 is disabled 1-0 EDIV[1:0] Free-Running ECLK Divider -- These bits determine the rate of the free-running clock on the ECLK pin. The usage of the bits is shown in Table 24-13. Divider is always disabled in emulation modes and active as programmed in all other operating modes. MC9S12XDP512 Data Sheet, Rev. 2.21 998 Freescale Semiconductor Table 24-13. Free-Running ECLK Clock Rate EDIV[1:0] Rate of Free-Running ECLK 00 ECLK = Bus clock rate 01 ECLK = Bus clock rate divided by 2 10 ECLK = Bus clock rate divided by 3 11 ECLK = Bus clock rate divided by 4 24.0.5.10 IRQ Control Register (IRQCR) 7 6 IRQE IRQEN 0 1 R 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 24-12. IRQ Control Register (IRQCR) Read: See individual bit descriptions below. Write: See individual bit descriptions below. Table 24-14. IRQCR Field Descriptions Field 7 IRQE 6 IRQEN Description IRQ Select Edge Sensitive Only Special modes: Read or write anytime. Normal and emulation modes: Read anytime, write once. 0 IRQ configured for low level recognition. 1 IRQ configured to respond only to falling edges. Falling edges on the IRQ pin will be detected anytime IRQE = 1 and will be cleared only upon a reset or the servicing of the IRQ interrupt. External IRQ Enable Read or write anytime. 0 External IRQ pin is disconnected from interrupt logic. 1 External IRQ pin is connected to interrupt logic. 24.0.5.11 Port K Data Register (PORTK) 7 R 6 5 4 3 2 1 0 PK5 PK4 PK3 PK2 PK1 PK0 0 0 0 0 0 0 0 PK7 W Reset 0 0 Figure 24-13. Port K Data Register (PORTK) Read: Anytime. Write: Anytime. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-15. PORTK Field Descriptions Field Description 7-0 PK[7,5:0] Port K -- Port K pins 7-0 can be used as general-purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read except for bit 6 which reads "0". 24.0.5.12 Port K Data Direction Register (DDRK) 7 R 6 5 4 3 2 1 0 DDRK5 DDRK4 DDRK3 DDRK2 DDRK1 DDRK0 0 0 0 0 0 0 0 DDRK7 W Reset 0 0 Figure 24-14. Port K Data Direction Register (DDRK) Read: Anytime. Write: Anytime. This register controls the data direction for port K. DDRK determines whether each pin (except PK6) is an input or output. A logic level "1" causes the associated port pin to be an output and a logic level "0" causes the associated pin to be a high-impedance input. Table 24-16. DDRK Field Descriptions Field Description 7-0 Data Direction Port K DDRK[7,5:0] 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PORTK after changing the DDRK register. 24.0.5.13 Port T Data Register (PTT) 7 6 5 4 3 2 1 0 PTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0 IOC7 IOC6 IOC5 IOC4 IOC3 IOC2 IOC1 IOC0 0 0 0 0 0 0 0 0 R W ECT Reset Figure 24-15. Port T Data Register (PTT) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 1000 Freescale Semiconductor Table 24-17. PTT Field Descriptions Field Description 7-0 PTT[7:0] Port T -- Port T bits 7-0 are associated with ECT channels IOC7-IOC0 (refer to ECT section). When not used with the ECT, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 24.0.5.14 Port T Input Register (PTIT) R 7 6 5 4 3 2 1 0 PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 24-16. Port T Input Register (PTIT) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. Table 24-18. PTIT Field Descriptions Field Description 7-0 PTIT[7:0] Port T Input -- This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. 24.0.5.15 Port T Data Direction Register (DDRT) 7 6 5 4 3 2 1 0 DDRT7 DDRT6 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0 0 0 0 0 0 0 0 0 R W Reset Figure 24-17. Port T Data Direction Register (DDRT) Read: Anytime. Write: Anytime. This register configures each port T pin as either input or output. The ECT forces the I/O state to be an output for each timer port associated with an enabled output compare. In this case the data direction bits will not change. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) The DDRT bits revert to controlling the I/O direction of a pin when the associated timer output compare is disabled. The timer input capture always monitors the state of the pin. Table 24-19. DDRT Field Descriptions Field Description 7-0 DDRT[7:0] Data Direction Port T 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTT or PTIT registers, when changing the DDRT register. 24.0.5.16 Port T Reduced Drive Register (RDRT) 7 6 5 4 3 2 1 0 RDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0 0 0 0 0 0 0 0 0 R W Reset Figure 24-18. Port T Reduced Drive Register (RDRT) Read: Anytime. Write: Anytime. This register configures the drive strength of each port T output pin as either full or reduced. If the port is used as input this bit is ignored. Table 24-20. RDRT Field Descriptions Field 7-0 RDRT[7:0] Description Reduced Drive Port T 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 24.0.5.17 Port T Pull Device Enable Register (PERT) 7 6 5 4 3 2 1 0 PERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0 0 0 0 0 0 0 0 0 R W Reset Figure 24-19. Port T Pull Device Enable Register (PERT) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 1002 Freescale Semiconductor This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 24-21. PERT Field Descriptions Field 7-0 PERT[7:0] Description Pull Device Enable Port T 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 24.0.5.18 Port T Polarity Select Register (PPST) 7 6 5 4 3 2 1 0 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0 0 0 0 0 0 0 0 R W Reset Figure 24-20. Port T Polarity Select Register (PPST) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. Table 24-22. PPST Field Descriptions Field Description 7-0 PPST[7:0] Pull Select Port T 0 A pull-up device is connected to the associated port T pin, if enabled by the associated bit in register PERT and if the port is used as input. 1 A pull-down device is connected to the associated port T pin, if enabled by the associated bit in register PERT and if the port is used as input. 24.0.5.19 Port S Data Register (PTS) 7 6 5 4 3 2 1 0 PTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0 SS0 SCK0 MOSI0 MISO0 TXD1 RXD1 TXD0 RXD0 0 0 0 0 0 0 0 0 R W SCI/SPI Reset Figure 24-21. Port S Data Register (PTS) Read: Anytime. Write: Anytime. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Port S pins 7-4 are associated with the SPI0. The SPI0 pin configuration is determined by several status bits in the SPI0 module. Refer to SPI section for details. When not used with the SPI0, these pins can be used as general purpose I/O. Port S bits 3-0 are associated with the SCI1 and SCI0. The SCI ports associated with transmit pins 3 and 1 are configured as outputs if the transmitter is enabled. The SCI ports associated with receive pins 2 and 0 are configured as inputs if the receiver is enabled. Refer to SCI section for details. When not used with the SCI, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. 24.0.5.20 Port S Input Register (PTIS) R 7 6 5 4 3 2 1 0 PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 24-22. Port S Input Register (PTIS) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This also can be used to detect overload or short circuit conditions on output pins. 24.0.5.21 Port S Data Direction Register (DDRS) 7 6 5 4 3 2 1 0 DDRS7 DDRS6 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0 0 0 0 0 0 0 0 0 R W Reset Figure 24-23. Port S Data Direction Register (DDRS) Read: Anytime. Write: Anytime. This register configures each port S pin as either input or output. If SPI0 is enabled, the SPI0 determines the pin direction. Refer to SPI section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 1004 Freescale Semiconductor If the associated SCI transmit or receive channel is enabled this register has no effect on the pins. The pin is forced to be an output if a SCI transmit channel is enabled, it is forced to be an input if the SCI receive channel is enabled. The DDRS bits revert to controlling the I/O direction of a pin when the associated channel is disabled. Table 24-23. DDRS Field Descriptions Field Description 7-0 DDRS[7:0] Data Direction Port S 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTS or PTIS registers, when changing the DDRS register. 24.0.5.22 Port S Reduced Drive Register (RDRS) 7 6 5 4 3 2 1 0 RDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0 0 0 0 0 0 0 0 0 R W Reset Figure 24-24. Port S Reduced Drive Register (RDRS) Read: Anytime. Write: Anytime. This register configures the drive strength of each port S output pin as either full or reduced. If the port is used as input this bit is ignored. Table 24-24. RDRS Field Descriptions Field 7-0 RDRS[7:0] Description Reduced Drive Port S 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 24.0.5.23 Port S Pull Device Enable Register (PERS) 7 6 5 4 3 2 1 0 PERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0 1 1 1 1 1 1 1 1 R W Reset Figure 24-25. Port S Pull Device Enable Register (PERS) Read: Anytime. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or as output in wired-OR (open drain) mode. This bit has no effect if the port is used as push-pull output. Out of reset a pull-up device is enabled. Table 24-25. PERS Field Descriptions Field 7-0 PERS[7:0] Description Pull Device Enable Port S 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 24.0.5.24 Port S Polarity Select Register (PPSS) 7 6 5 4 3 2 1 0 PPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0 0 0 0 0 0 0 0 0 R W Reset Figure 24-26. Port S Polarity Select Register (PPSS) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. Table 24-26. PPSS Field Descriptions Field Description 7-0 PPSS[7:0] Pull Select Port S 0 A pull-up device is connected to the associated port S pin, if enabled by the associated bit in register PERS and if the port is used as input or as wired-OR output. 1 A pull-down device is connected to the associated port S pin, if enabled by the associated bit in register PERS and if the port is used as input. 24.0.5.25 Port S Wired-OR Mode Register (WOMS) 7 6 5 4 3 2 1 0 WOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0 0 0 0 0 0 0 0 0 R W Reset Figure 24-27. Port S Wired-OR Mode Register (WOMS) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 1006 Freescale Semiconductor This register configures the output pins as wired-OR. If enabled the output is driven active low only (open-drain). A logic level of "1" is not driven. It applies also to the SPI and SCI outputs and allows a multipoint connection of several serial modules. These bits have no influence on pins used as inputs. Table 24-27. WOMS Field Descriptions Field Description 7-0 Wired-OR Mode Port S WOMS[7:0] 0 Output buffers operate as push-pull outputs. 1 Output buffers operate as open-drain outputs. 24.0.5.26 Port M Data Register (PTM) 7 6 5 4 3 2 1 0 PTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0 TXCAN0 RXCAN0 0 0 R W CAN Routed CAN0 Routed CAN4 TXCAN4 RXCAN4 Routed SPI0 Reset 0 0 TXCAN0 RXCAN0 TXCAN0 RXCAN0 TXCAN4 RXCAN4 SCK0 MOSI0 SS0 MISO0 0 0 0 0 Figure 24-28. Port M Data Register (PTM) Read: Anytime. Write: Anytime. Port M pins 7-0 are associated with the CAN0, as well as the routed CAN0, CAN4, and SPI0 modules. When not used with any of the peripherals, these pins can be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. Table 24-28. PTM Field Descriptions Field Description 7-6 PTM[7:6] The CAN4 function (TXCAN4 and RXCAN4) takes precedence over the general purpose I/O function if the CAN4 module is enabled. Refer to MSCAN section for details. 5-4 PTM[5:4] The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the routed CAN4, the routed SPI0 and the general purpose I/O function if the routed CAN0 module is enabled. The routed CAN4 function (TXCAN4 and RXCAN4) takes precedence over the routed SPI0 and general purpose I/O function if the routed CAN4 module is enabled. Refer to MSCAN section for details. The routed SPI0 function (SCK0 and MOSI0) takes precedence of the general purpose I/O function if the routed SPI0 is enabled. Refer to SPI section for details. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-28. PTM Field Descriptions (continued) Field 3-2 PTM[3:2] Description The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the routed SPI0 and the general purpose I/O function if the routed CAN0 module is enabled. Refer to MSCAN section for details. The routed SPI0 function (SS0 and MISO0) takes precedence of the general purpose I/O function if the routed SPI0 is enabled and not in bidirectional mode. Refer to SPI section for details. 1-0 PTM[1:0] The CAN0 function (TXCAN0 and RXCAN0) takes precedence over the general purpose I/O function if the CAN0 module is enabled. Refer to MSCAN section for details. 24.0.5.27 Port M Input Register (PTIM) R 7 6 5 4 3 2 1 0 PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 24-29. Port M Input Register (PTIM) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. 24.0.5.28 Port M Data Direction Register (DDRM) 7 6 5 4 3 2 1 0 DDRM7 DDRM6 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0 0 0 0 0 0 0 0 0 R W Reset Figure 24-30. Port M Data Direction Register (DDRM) Read: Anytime. Write: Anytime. This register configures each port M pin as either input or output. The CAN forces the I/O state to be an output for each port line associated with an enabled output (TXCAN). It also forces the I/O state to be an input for each port line associated with an enabled input (RXCAN). In those cases the data direction bits will not change. MC9S12XDP512 Data Sheet, Rev. 2.21 1008 Freescale Semiconductor The DDRM bits revert to controlling the I/O direction of a pin when the associated peripheral module is disabled. Table 24-29. DDRM Field Descriptions Field Description 7-0 DDRM[7:0] Data Direction Port M 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTM or PTIM registers, when changing the DDRM register. 24.0.5.29 Port M Reduced Drive Register (RDRM) 7 6 5 4 3 2 1 0 RDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0 0 0 0 0 0 0 0 0 R W Reset Figure 24-31. Port M Reduced Drive Register (RDRM) Read: Anytime. Write: Anytime. This register configures the drive strength of each Port M output pin as either full or reduced. If the port is used as input this bit is ignored. Table 24-30. RDRM Field Descriptions Field 7-0 RDRM[7:0] Description Reduced Drive Port M 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 24.0.5.30 Port M Pull Device Enable Register (PERM) 7 6 5 4 3 2 1 0 PERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0 0 0 0 0 0 0 0 0 R W Reset Figure 24-32. Port M Pull Device Enable Register (PERM) Read: Anytime. Write: Anytime. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset no pull device is enabled. Table 24-31. PERM Field Descriptions Field 7-0 PERM[7:0] Description Pull Device Enable Port M 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 24.0.5.31 Port M Polarity Select Register (PPSM) 7 6 5 4 3 2 1 0 PPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0 0 0 0 0 0 0 0 0 R W Reset Figure 24-33. Port M Polarity Select Register (PPSM) Read: Anytime. Write: Anytime. This register selects whether a pull-down or a pull-up device is connected to the pin. If CAN is active, a pull-up device can be activated on the related RXCAN inputs, but not a pull-down. Table 24-32. PPSM Field Descriptions Field Description 7-0 PPSM[7:0] Pull Select Port M 0 A pull-up device is connected to the associated port M pin, if enabled by the associated bit in register PERM and if the port is used as general purpose or RXCAN input. 1 A pull-down device is connected to the associated port M pin, if enabled by the associated bit in register PERM and if the port is used as a general purpose but not as RXCAN. 24.0.5.32 Port M Wired-OR Mode Register (WOMM) 7 6 5 4 3 2 1 0 WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 0 0 0 0 0 0 0 0 R W Reset Figure 24-34. Port M Wired-OR Mode Register (WOMM) Read: Anytime. Write: Anytime. MC9S12XDP512 Data Sheet, Rev. 2.21 1010 Freescale Semiconductor This register configures the output pins as wired-OR. If enabled the output is driven active low only (open-drain). A logic level of "1" is not driven. It applies also to the CAN outputs and allows a multipoint connection of several serial modules. This bit has no influence on pins used as inputs. Table 24-33. WOMM Field Descriptions Field Description 7-0 Wired-OR Mode Port M WOMM[7:0] 0 Output buffers operate as push-pull outputs. 1 Output buffers operate as open-drain outputs. 24.0.5.33 Module Routing Register (MODRR) 7 R 0 6 5 4 3 2 1 0 MODRR61 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0 0 0 0 0 0 0 0 W Reset 0 = Unimplemented or Reserved Figure 24-35. Module Routing Register (MODRR) 1. Register implemented, function disabled: Written values can be read back. Read: Anytime. Write: Anytime. This register configures the re-routing of CAN0, CAN4, SPI0, SPI1 on alternative ports. Table 24-34. Module Routing Summary MODRR Related Pins Module CAN0 CAN4 SPI0 SPI1 6 5 4 3 2 1 0 RXCAN TXCAN x x x x x 0 0 PM0 PM1 x x x x x 0 1 PM2 PM3 x x x x x 1 0 PM4 PM5 x x x x x 1 1 PJ6 PJ7 x x x 0 0 x x PJ6 PJ7 x x x 0 1 x x PM4 PM5 x x x 1 0 x x PM6 PM7 x x x 1 1 x x Reserved MISO MOSI SCK SS x x 0 x x x x PS4 PS5 PS6 PS7 x x 1 x x x x PM2 PM4 PM5 PM3 x 0 x x x x x PP0 PP1 PP2 PP3 x 1 x x x x x PH0 PH1 PH2 PH3 Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.5.34 Port P Data Register (PTP) 7 6 5 4 3 2 1 0 PTP7 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0 PWM7 PWM6 PWM5 PWM4 PWM3 PWM2 PWM1 PWM0 SS1 SCK1 MOSI1 MISO1 0 0 0 0 R W PWM SPI Reset 0 0 0 0 Figure 24-36. Port P Data Register (PTP) Read: Anytime. Write: Anytime. Port P pins 7-0 are associated with the PWM as well as the SPI1. These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. The PWM function takes precedence over the general purpose I/O and the SPI1 function if the associated PWM channel is enabled. While channels 6-0 are output only if the respective channel is enabled, channel 7 can be PWM output or input if the shutdown feature is enabled. Refer to PWM section for details. The SPI1 function takes precedence over the general purpose I/O function if enabled. Refer to SPI section for details. 24.0.5.35 Port P Input Register (PTIP) R 7 6 5 4 3 2 1 0 PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 24-37. Port P Input Register (PTIP) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. MC9S12XDP512 Data Sheet, Rev. 2.21 1012 Freescale Semiconductor 24.0.5.36 Port P Data Direction Register (DDRP) 7 6 5 4 3 2 1 0 DDRP7 DDRP6 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0 0 0 0 0 0 0 0 0 R W Reset Figure 24-38. Port P Data Direction Register (DDRP) Read: Anytime. Write: Anytime. This register configures each port P pin as either input or output. If the associated PWM channel or SPI module is enabled this register has no effect on the pins. The PWM forces the I/O state to be an output for each port line associated with an enabled PWM7- 0 channel. Channel 7 can force the pin to input if the shutdown feature is enabled. Refer to PWM section for details. If SPI is enabled, the SPI determines the pin direction. Refer to SPI section for details. The DDRP bits revert to controlling the I/O direction of a pin when the associated peripherals are disabled. Table 24-35. DDRP Field Descriptions Field Description 7-0 DDRP[7:0] Data Direction Port P 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTP or PTIP registers, when changing the DDRP register. 24.0.5.37 Port P Reduced Drive Register (RDRP) 7 6 5 4 3 2 1 0 RDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0 0 0 0 0 0 0 0 0 R W Reset Figure 24-39. Port P Reduced Drive Register (RDRP) Read: Anytime. Write: Anytime. This register configures the drive strength of each port P output pin as either full or reduced. If the port is used as input this bit is ignored. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-36. RDRP Field Descriptions Field 7-0 RDRP[7:0] Description Reduced Drive Port P 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 24.0.5.38 Port P Pull Device Enable Register (PERP) 7 6 5 4 3 2 1 0 PERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0 0 0 0 0 0 0 0 0 R W Reset Figure 24-40. Port P Pull Device Enable Register (PERP) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 24-37. PERP Field Descriptions Field 7-0 PERP[7:0] Description Pull Device Enable Port P 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 24.0.5.39 Port P Polarity Select Register (PPSP) 7 6 5 4 3 2 1 0 PPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSP0 0 0 0 0 0 0 0 0 R W Reset Figure 24-41. Port P Polarity Select Register (PPSP) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 1014 Freescale Semiconductor Table 24-38. PPSP Field Descriptions Field Description 7-0 PPSP[7:0] Polarity Select Port P 0 Falling edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-up device is connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is used as input. 1 Rising edge on the associated port P pin sets the associated flag bit in the PIFP register.A pull-down device is connected to the associated port P pin, if enabled by the associated bit in register PERP and if the port is used as input. 24.0.5.40 Port P Interrupt Enable Register (PIEP) 7 6 5 4 3 2 1 0 PIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0 0 0 0 0 0 0 0 0 R W Reset Figure 24-42. Port P Interrupt Enable Register (PIEP) Read: Anytime. Write: Anytime. This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port P. Table 24-39. PIEP Field Descriptions Field 7-0 PIEP[7:0] Description Interrupt Enable Port P 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. 24.0.5.41 Port P Interrupt Flag Register (PIFP) 7 6 5 4 3 2 1 0 PIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0 0 0 0 0 0 0 0 0 R W Reset Figure 24-43. Port P Interrupt Flag Register (PIFP) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSP register. To clear this flag, write logic level "1" to the corresponding bit in the PIFP register. Writing a "0" has no effect. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-40. PIFP Field Descriptions Field 7-0 PIFP[7:0] Description Interrupt Flags Port P 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. 24.0.5.42 Port H Data Register (PTH) 7 6 5 4 3 2 1 0 PTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0 SS1 SCK1 MOSI1 MISO1 0 0 0 0 R W Routed SPI Reset 0 0 0 0 Figure 24-44. Port H Data Register (PTH) Read: Anytime. Write: Anytime. Port H pins 7-0 are associated with the routed SPI1. These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read. The routed SPI1 function takes precedence over the general purpose I/O function if the routed SPI1 is enabled. Refer to SPI section for details. 24.0.5.43 Port H Input Register (PTIH) R 7 6 5 4 3 2 1 0 PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0 -- -- -- -- -- -- -- -- W Reset1 = Unimplemented or Reserved Figure 24-45. Port H Input Register (PTIH) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. MC9S12XDP512 Data Sheet, Rev. 2.21 1016 Freescale Semiconductor This register always reads back the buffered state of the associated pins. This can also be used to detect overload or short circuit conditions on output pins. 24.0.5.44 Port H Data Direction Register (DDRH) 7 6 5 4 3 2 1 0 DDRH7 DDRH6 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 0 0 0 0 0 0 0 0 R W Reset Figure 24-46. Port H Data Direction Register (DDRH) Read: Anytime. Write: Anytime. This register configures each port H pin as either input or output. If the associated routed SPI module is enabled this register has no effect on the pins. If a SPI module is enabled, the SPI determines the pin direction. Refer to SPI section for details. The DDRH bits revert to controlling the I/O direction of a pin when the associated peripheral modules are disabled. Table 24-41. DDRH Field Descriptions Field Description 7-0 DDRH[7:0] Data Direction Port H 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTH or PTIH registers, when changing the DDRH register. 24.0.5.45 Port H Reduced Drive Register (RDRH) 7 6 5 4 3 2 1 0 RDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0 0 0 0 0 0 0 0 0 R W Reset Figure 24-47. Port H Reduced Drive Register (RDRH) Read: Anytime. Write: Anytime. This register configures the drive strength of each Port H output pin as either full or reduced. If the port is used as input this bit is ignored. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-42. RDRH Field Descriptions Field 7-0 RDRH[7:0] Description Reduced Drive Port H 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 24.0.5.46 Port H Pull Device Enable Register (PERH) 7 6 5 4 3 2 1 0 PERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0 0 0 0 0 0 0 0 0 R W Reset Figure 24-48. Port H Pull Device Enable Register (PERH) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull device is enabled. Table 24-43. PERH Field Descriptions Field 7-0 PERH[7:0] Description Pull Device Enable Port H 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 24.0.5.47 Port H Polarity Select Register (PPSH) 7 6 5 4 3 2 1 0 PPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0 0 0 0 0 0 0 0 0 R W Reset Figure 24-49. Port H Polarity Select Register (PPSH) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 1018 Freescale Semiconductor Table 24-44. PPSH Field Descriptions Field Description 7-0 PPSH[7:0] Polarity Select Port H 0 Falling edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-up device is connected to the associated port H pin, if enabled by the associated bit in register PERH and if the port is used as input. 1 Rising edge on the associated port H pin sets the associated flag bit in the PIFH register. A pull-down device is connected to the associated port H pin, if enabled by the associated bit in register PERH and if the port is used as input. 24.0.5.48 Port H Interrupt Enable Register (PIEH) 7 6 5 4 3 2 1 0 PIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0 0 0 0 0 0 0 0 0 R W Reset Figure 24-50. Port H Interrupt Enable Register (PIEH) Read: Anytime. Write: Anytime. This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port H. Table 24-45. PIEH Field Descriptions Field 7-0 PIEH[7:0] Description Interrupt Enable Port H 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. 24.0.5.49 Port H Interrupt Flag Register (PIFH) 7 6 5 4 3 2 1 0 PIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0 0 0 0 0 0 0 0 0 R W Reset Figure 24-51. Port H Interrupt Flag Register (PIFH) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSH register. To clear this flag, write logic level "1" to the corresponding bit in the PIFH register. Writing a "0" has no effect. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-46. PIFH Field Descriptions Field 7-0 PIFH[7:0] Description Interrupt Flags Port H 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. 24.0.5.50 Port J Data Register (PTJ) 7 6 PTJ7 PTJ6 TXCAN4 RXCAN4 SCL0 SDA0 TXCAN0 RXCAN0 0 0 R 5 4 3 2 0 0 0 0 1 0 PTJ1 PTJ0 0 0 W CAN4 IIC0 Routed CAN0 Reset 0 0 0 0 = Unimplemented or Reserved Figure 24-52. Port J Data Register (PTJ) Read: Anytime. Write: Anytime. Port J pins 7-6 are associated with the CAN4, IIC0, the routed CAN0 modules. These pins can be used as general purpose I/O when not used with any of the peripherals. If the data direction bits of the associated I/O pins are set to logic level "1", a read returns the value of the port register, otherwise the buffered pin input state is read except for bits 5-2 which read "0". Table 24-47. PTJ Field Descriptions Field Description 7-6 PJ[7:6] The CAN4 function (TXCAN4 and RXCAN4) takes precedence over the IIC0, the routed CAN0 and the general purpose I/O function if the CAN4 module is enabled. The IIC0 function (SCL0 and SDA0) takes precedence over the routed CAN0 and the general purpose I/O function if the IIC0 is enabled. If the IIC0 module takes precedence the SDA0 and SCL0 outputs are configured as open drain outputs. Refer to IIC section for details. The routed CAN0 function (TXCAN0 and RXCAN0) takes precedence over the general purpose I/O function if the routed CAN0 module is enabled. Refer to MSCAN section for details. MC9S12XDP512 Data Sheet, Rev. 2.21 1020 Freescale Semiconductor 24.0.5.51 Port J Input Register (PTIJ) R 7 6 5 4 3 2 1 0 PTIJ7 PTIJ6 0 0 0 0 PTIJ1 PTIJ0 0 0 0 0 0 0 0 0 W Reset1 = Unimplemented or Reserved Figure 24-53. Port J Input Register (PTIJ) 1. These registers are reset to zero. Two bus clock cycles after reset release the register values are updated with the associated pin values. Read: Anytime. Write: Never, writes to this register have no effect. This register always reads back the buffered state of the associated pins. This can be used to detect overload or short circuit conditions on output pins. 24.0.5.52 Port J Data Direction Register (DDRJ) 7 6 DDRJ7 DDRJ6 0 0 R 5 4 3 2 0 0 0 0 1 0 DDRJ1 DDRJ0 0 0 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 24-54. Port J Data Direction Register (DDRJ) Read: Anytime. Write: Anytime. This register configures each port J pin (except PJ5-2) as either input or output. The CAN forces the I/O state to be an output on PJ7 (TXCAN4) and an input on pin PJ6 (RXCAN4). The IIC takes control of the I/O if enabled. In these cases the data direction bits will not change. The DDRJ bits revert to controlling the I/O direction of a pin when the associated peripheral module is disabled. Table 24-48. DDRJ Field Descriptions Field Description 7-0 DDRJ[7:6] DDRJ[1:0] Data Direction Port J 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTJ or PTIJ registers, when changing the DDRJ register. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.5.53 Port J Reduced Drive Register (RDRJ) 7 6 RDRJ7 RDRJ6 0 0 R 5 4 3 2 0 0 0 0 1 0 RDRJ1 RDRJ0 0 0 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 24-55. Port J Reduced Drive Register (RDRJ) Read: Anytime. Write: Anytime. This register configures the drive strength of each port J output pin as either full or reduced. If the port is used as input this bit is ignored. Table 24-49. RDRJ Field Descriptions Field 7-0 RDRJ[7:6] RDRJ[1:0] Description Reduced Drive Port J 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 24.0.5.54 Port J Pull Device Enable Register (PERJ) 7 6 PERJ7 PERJ6 1 1 R 5 4 3 2 0 0 0 0 1 0 PERJ1 PERJ0 1 1 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 24-56. Port J Pull Device Enable Register (PERJ) Read: Anytime. Write: Anytime. This register configures whether a pull-up or a pull-down device is activated, if the port is used as input or as wired-OR output. This bit has no effect if the port is used as push-pull output. Out of reset a pull-up device is enabled. MC9S12XDP512 Data Sheet, Rev. 2.21 1022 Freescale Semiconductor Table 24-50. PERJ Field Descriptions Field 7-0 PERJ[7:6] PERJ[1:0] Description Pull Device Enable Port J 0 Pull-up or pull-down device is disabled. 1 Either a pull-up or pull-down device is enabled. 24.0.5.55 Port J Polarity Select Register (PPSJ) 7 6 PPSJ7 PPSJ6 0 0 R 5 4 3 2 0 0 0 0 1 0 PPSJ1 PPSJ0 0 0 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 24-57. Port J Polarity Select Register (PPSJ) Read: Anytime. Write: Anytime. This register serves a dual purpose by selecting the polarity of the active interrupt edge as well as selecting a pull-up or pull-down device if enabled. Table 24-51. PPSJ Field Descriptions Field Description 7-0 PPSJ[7:6] PPSJ[1:0] Polarity Select Port J 0 Falling edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-up device is connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is used as general purpose input or as IIC port. 1 Rising edge on the associated port J pin sets the associated flag bit in the PIFJ register. A pull-down device is connected to the associated port J pin, if enabled by the associated bit in register PERJ and if the port is used as input. 24.0.5.56 Port J Interrupt Enable Register (PIEJ) 7 6 PIEJ7 PIEJ6 0 0 R 5 4 3 2 0 0 0 0 1 0 PIEJ1 PIEJ0 0 0 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 24-58. Port J Interrupt Enable Register (PIEJ) This register disables or enables on a per-pin basis the edge sensitive external interrupt associated with Port J. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Table 24-52. PIEJ Field Descriptions Field 7-0 PIEJ[7:6] PIEJ[1:0] Description Interrupt Enable Port J 0 Interrupt is disabled (interrupt flag masked). 1 Interrupt is enabled. 24.0.5.57 Port J Interrupt Flag Register (PIFJ) 7 6 PIFJ7 PIFJ6 0 0 R 5 4 3 2 0 0 0 0 1 0 PIFJ1 PIFJ0 0 0 W Reset 0 0 0 0 = Unimplemented or Reserved Figure 24-59. Port J Interrupt Flag Register (PIFJ) Read: Anytime. Write: Anytime. Each flag is set by an active edge on the associated input pin. This could be a rising or a falling edge based on the state of the PPSJ register. To clear this flag, write logic level "1" to the corresponding bit in the PIFJ register. Writing a "0" has no effect. Table 24-53. PIEJ Field Descriptions Field 7-0 PIFJ[7:6] PIFJ[1:0] Description Interrupt Flags Port J 0 No active edge pending. Writing a "0" has no effect. 1 Active edge on the associated bit has occurred (an interrupt will occur if the associated enable bit is set). Writing a logic level "1" clears the associated flag. 24.0.5.58 Port AD1 Data Register 0 (PT0AD1) 7 6 5 4 3 2 1 0 PT0AD115 PT0AD114 PT0AD113 PT0AD112 PT0AD111 PT0AD110 PT0AD19 PT0AD18 0 0 0 0 0 0 0 0 R W Reset Figure 24-60. Port AD1 Data Register 0 (PT0AD1) Read: Anytime. Write: Anytime. This register is associated with AD1 pins PAD[15:8]. These pins can also be used as general purpose I/O. MC9S12XDP512 Data Sheet, Rev. 2.21 1024 Freescale Semiconductor If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. 24.0.5.59 Port AD1 Data Register 1 (PT1AD1) 7 6 5 4 3 2 1 0 PT1AD17 PT1AD16 PT1AD15 PT1AD14 PT1AD13 PT1AD12 PT1AD11 PT1AD10 0 0 0 0 0 0 0 0 R W Reset Figure 24-61. Port AD1 Data Register 1 (PT1AD1) Read: Anytime. Write: Anytime. This register is associated with AD1 pins PAD[7:0]. These pins can also be used as general purpose I/O. If the data direction bits of the associated I/O pins are set to 1, a read returns the value of the port register, otherwise the value at the pins is read. 24.0.5.60 Port AD1 Data Direction Register 0 (DDR0AD1) 7 6 5 4 3 2 1 0 R DDR0AD115 DDR0AD114 DDR0AD113 DDR0AD112 DDR0AD111 DDR0AD110 DDR0AD19 DDR0AD18 W Reset 0 0 0 0 0 0 0 0 Figure 24-62. Port AD1 Data Direction Register 0 (DDR0AD1) Read: Anytime. Write: Anytime. This register configures pin PAD[15:8] as either input or output. Table 24-54. DDR0AD1 Field Descriptions Field Description 7-0 DDR0AD1[15:8] Data Direction Port AD1 Register 0 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD10 register, when changing the DDR0AD1 register. Note: To use the digital input function on Port AD1 the ATD1 digital input enable register (ATD1DIEN0) has to be set to logic level "1". Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.5.61 Port AD1 Data Direction Register 1 (DDR1AD1) 7 6 5 4 3 2 1 0 DDR1AD17 DDR1AD16 DDR1AD15 DDR1AD14 DDR1AD13 DDR1AD12 DDR1AD11 DDR1AD10 0 0 0 0 0 0 0 0 R W Reset Figure 24-63. Port AD1 Data Direction Register 1 (DDR1AD1) Read: Anytime. Write: Anytime. This register configures pins PAD[7:0] as either input or output. Table 24-55. DDR1AD1 Field Descriptions Field Description 7-0 DDR1AD1[7:0] Data Direction Port AD1 Register 1 0 Associated pin is configured as input. 1 Associated pin is configured as output. Note: Due to internal synchronization circuits, it can take up to 2 bus clock cycles until the correct value is read on PTAD11 register, when changing the DDR1AD1 register. Note: To use the digital input function on port AD1 the ATD1 digital input enable register (ATD1DIEN1) has to be set to logic level "1". 24.0.5.62 Port AD1 Reduced Drive Register 0 (RDR0AD1) 7 6 5 4 3 2 1 0 R RDR0AD115 RDR0AD114 RDR0AD113 RDR0AD112 RDR0AD111 RDR0AD110 RDR0AD19 RDR0AD18 W Reset 0 0 0 0 0 0 0 0 Figure 24-64. Port AD1 Reduced Drive Register 0 (RDR0AD1) Read: Anytime. Write: Anytime. This register configures the drive strength of each PAD[15:8] output pin as either full or reduced. If the port is used as input this bit is ignored. Table 24-56. RDR0AD1 Field Descriptions Field 7-0 RDR0AD1[15:8] Description Reduced Drive Port AD1 Register 0 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. MC9S12XDP512 Data Sheet, Rev. 2.21 1026 Freescale Semiconductor 24.0.5.63 Port AD1 Reduced Drive Register 1 (RDR1AD1) 7 6 5 4 3 2 1 0 RDR1AD17 RDR1AD16 RDR1AD15 RDR1AD14 RDR1AD13 RDR1AD12 RDR1AD11 RDR1AD10 0 0 0 0 0 0 0 0 R W Reset Figure 24-65. Port AD1 Reduced Drive Register 1 (RDR1AD1) Read: Anytime. Write: Anytime. This register configures the drive strength of each PAD[7:0] output pin as either full or reduced. If the port is used as input this bit is ignored. Table 24-57. RDR1AD1 Field Descriptions Field Description 7-0 RDR1AD1[7:0] Reduced Drive Port AD1 Register 1 0 Full drive strength at output. 1 Associated pin drives at about 1/6 of the full drive strength. 24.0.5.64 Port AD1 Pull Up Enable Register 0 (PER0AD1) 7 6 5 4 3 2 1 0 PER0AD19 PER0AD18 0 0 R PER0AD115 PER0AD114 PER0AD113 PER0AD112 PER0AD111 PER0AD110 W Reset 0 0 0 0 0 0 Figure 24-66. Port AD1 Pull Up Enable Register 0 (PER0AD1) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective PAD[15:8] pin if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull-up device is enabled. Table 24-58. PER0AD1 Field Descriptions Field 7-0 PER0AD1[15:8] Description Pull Device Enable Port AD1 Register 0 0 Pull-up device is disabled. 1 Pull-up device is enabled. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.5.65 Port AD1 Pull Up Enable Register 1 (PER1AD1) 7 6 5 4 3 2 1 0 PER1AD17 PER1AD16 PER1AD15 PER1AD14 PER1AD13 PER1AD12 PER1AD11 PER1AD10 0 0 0 0 0 0 0 0 R W Reset Figure 24-67. Port AD1 Pull Up Enable Register 1 (PER1AD1) Read: Anytime. Write: Anytime. This register activates a pull-up device on the respective PAD[7:0] pin if the port is used as input. This bit has no effect if the port is used as output. Out of reset no pull-up device is enabled. Table 24-59. PER1AD1 Field Descriptions Field Description 7-0 PER1AD1[7:0] Pull Device Enable Port AD1 Register 1 0 Pull-up device is disabled. 1 Pull-up device is enabled. Functional Description Each pin except PE0, PE1, and BKGD can act as general purpose I/O. In addition each pin can act as an output from the external bus interface module or a peripheral module or an input to the external bus interface module or a peripheral module. A set of configuration registers is common to all ports with exceptions in the expanded bus interface and ATD ports (Table 24-60). All registers can be written at any time; however a specific configuration might not become active. Example: Selecting a pull-up device This device does not become active while the port is used as a push-pull output. Table 24-60. Register Availability per Port1 Port Data Data Direction Input Reduced Drive Pull Enable Polarity Select Wired-OR Mode Interrupt Enable Interrupt Flag A yes yes -- yes yes -- -- -- -- B yes yes -- -- -- -- -- E yes yes -- -- -- -- -- K yes yes -- -- -- -- -- T yes yes yes yes yes -- -- -- -- S yes yes yes yes yes yes yes -- -- M yes yes yes yes yes yes yes -- -- P yes yes yes yes yes yes -- yes yes H yes yes yes yes yes yes -- yes yes MC9S12XDP512 Data Sheet, Rev. 2.21 1028 Freescale Semiconductor Table 24-60. Register Availability per Port1 Port Data Data Direction Input Reduced Drive Pull Enable Polarity Select Wired-OR Mode Interrupt Enable Interrupt Flag J yes yes yes yes yes yes -- yes yes AD1 yes yes -- yes yes -- -- -- -- 1. Each cell represents one register with individual configuration bits 24.0.6 24.0.6.1 Registers Data Register This register holds the value driven out to the pin if the pin is used as a general purpose I/O. Writing to this register has only an effect on the pin if the pin is used as general purpose output. When reading this address, the buffered state of the pin is returned if the associated data direction register bit is set to "0". If the data direction register bits are set to logic level "1", the contents of the data register is returned. This is independent of any other configuration (Figure 24-68). 24.0.6.2 Input Register This is a read-only register and always returns the buffered state of the pin (Figure 24-68). 24.0.6.3 Data Direction Register This register defines whether the pin is used as an input or an output. If a peripheral module controls the pin the contents of the data direction register is ignored (Figure 24-68). PTI 0 1 PT 0 PIN 1 DDR 0 1 data out Module output enable module enable Figure 24-68. Illustration of I/O Pin Functionality Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) 24.0.6.4 Reduced Drive Register If the pin is used as an output this register allows the configuration of the drive strength. 24.0.6.5 Pull Device Enable Register This register turns on a pull-up or pull-down device. It becomes active only if the pin is used as an input or as a wired-OR output. 24.0.6.6 Polarity Select Register This register selects either a pull-up or pull-down device if enabled. It becomes active only if the pin is used as an input. A pull-up device can be activated if the pin is used as a wired-OR output. If the pin is used as an interrupt input this register selects the active interrupt edge. 24.0.6.7 Wired-OR Mode Register If the pin is used as an output this register turns off the active high drive. This allows wired-OR type connections of outputs. 24.0.6.8 Interrupt Enable Register If the pin is used as an interrupt input this register serves as a mask to the interrupt flag to enable/disable the interrupt. 24.0.6.9 Interrupt Flag Register If the pin is used as an interrupt input this register holds the interrupt flag after a valid pin event. 24.0.6.10 Module Routing Register This register supports the re-routing of the CAN0, CAN4, SPI0, SPI1, and SPI2 pins to alternative ports. This allows a software re-configuration of the pinouts of the different package options with respect to above peripherals. NOTE The purpose of the module routing register is to provide maximum flexibility for derivatives with a lower number of MSCAN and SPI modules. MC9S12XDP512 Data Sheet, Rev. 2.21 1030 Freescale Semiconductor Table 24-61. Module Implementations on Derivatives MSCAN Modules SPI Modules Number of Modules CAN0 CAN1 CAN2 CAN3 CAN4 SPI0 SPI1 SPI2 5 yes yes yes yes yes -- -- -- 4 yes yes yes -- yes -- -- -- 3 yes yes -- -- yes yes yes yes 2 yes -- -- -- yes yes yes -- 1 yes -- -- -- -- yes -- -- 24.0.7 24.0.7.1 Ports BKGD Pin The BKGD pin is associated with the S12X_BDM and S12X_EBI modules. During reset, the BKGD pin is used as MODC input. 24.0.7.2 Port A and B Port A pins PA[7:0] and Port B pins PB[7:0] can be used for either general-purpose I/O. 24.0.7.3 Port E Port E pins PE[7:2] can be used for either general-purpose I/O or with the alternative functions. Port E pin PE[7] an be used for either general-purpose I/O or as the free-running clock ECLKX2 output running at the core clock rate. The clock output is always enabled in emulation modes. Port E pin PE[4] an be used for either general-purpose I/O or as the free-running clock ECLK output running at the bus clock rate or at the programmed divided clock rate. The clock output is always enabled in emulation modes. Port E pin PE[1] can be used for either general-purpose input or as the level- or falling edgesensitive IRQ interrupt input. IRQ will be enabled by setting the IRQEN configuration bit (Section 24.0.5.10, "IRQ Control Register (IRQCR)") and clearing the I-bit in the CPU's condition code register. It is inhibited at reset so this pin is initially configured as a simple input with a pullup. Port E pin PE[0] can be used for either general-purpose input or as the level-sensitive XIRQ interrupt input. XIRQ can be enabled by clearing the X-bit in the CPU's condition code register. It is inhibited at reset so this pin is initially configured as a high-impedance input with a pull-up. 24.0.7.4 Port K Port K pins PK[7:0] can be used for either general-purpose I/O. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Port K pin PE[7] is configured for reduced input threshold in certain modes (refer to S12X_EBI section). NOTE Port K is not available in 80-pin packages. 24.0.7.5 Port T This port is associated with the ECT module. Port T pins PT[7:0] can be used for either general-purpose I/O, or with the channels of the enhanced capture timer. 24.0.7.6 Port S This port is associated with SCI0, SCI1 and SPI0. Port S pins PS[7:0] can be used either for generalpurpose I/O, or with the SCI and SPI subsystems. The SPI0 pins can be re-routed. Refer to Section 24.0.5.33, "Module Routing Register (MODRR)". NOTE PS[7:4] are not available in 80-pin packages. 24.0.7.7 Port M This port is associated with the CAN4 and 0 and SPI0. Port M pins PM[7:0] can be used for either general purpose I/O, or with the CAN, SCI and SPI subsystems. The CAN0, CAN4 and SPI0 pins can be re-routed. Refer to Section 24.0.5.33, "Module Routing Register (MODRR)". NOTE PM[7:6] are not available in 80-pin packages. 24.0.7.8 Port P This port is associated with the PWM, SPI1. Port P pins PP[7:0] can be used for either general purpose I/ O, or with the PWM and SPI subsystems. The pins are shared between the PWM channels and the SPI1. If the PWM is enabled the pins become PWM output channels with the exception of pin 7 which can be PWM input or output. If SPI1is enabled and PWM is disabled, the respective pin configuration is determined by status bits in the SPI. The SPI1 pins can be re-routed. Refer to Section 24.0.5.33, "Module Routing Register (MODRR)". Port P offers 8 I/O pins with edge triggered interrupt capability in wired-OR fashion (Section 24.0.8, "Pin Interrupts"). NOTE PP[6] is not available in 80-pin packages. MC9S12XDP512 Data Sheet, Rev. 2.21 1032 Freescale Semiconductor 24.0.7.9 Port H This port is associated with the SPI1, . Port H pins PH[7:0] can be used for either general purpose I/O, or with the SPI and SCI subsystems. Port H pins can be used with the routed SPI1. Refer to Section 24.0.5.33, "Module Routing Register (MODRR)". Port H offers 8 I/O pins with edge triggered interrupt capability (Section 24.0.8, "Pin Interrupts"). NOTE Port H is not available in 80-pin packages. 24.0.7.10 Port J This port is associated with CAN4, CAN0, IIC0. Port J pins PJ[7:4] and PJ[2:0] can be used for either general purpose I/O, or with the CAN, IIC, or SCI subsystems. If IIC takes precedence the associated pins become IIC open-drain output pins. The CAN4 pins can be re-routed. Refer to Section 24.0.5.33, "Module Routing Register (MODRR)". Port J pins can be used with the routed CAN0 modules. Refer to Section 24.0.5.33, "Module Routing Register (MODRR)". Port J offers 7 I/O pins with edge triggered interrupt capability (Section 24.0.8, "Pin Interrupts"). NOTE PJ[5,4,2,1,0] are not available in 80-pin packages. 24.0.7.11 Port AD1 This port is associated with the ATD1. Port AD1 pins PAD15-PAD0 can be used for either general purpose I/O, or with the ATD1 subsystem. NOTE PAD[15:8] are not available in 80-pin packages. 24.0.8 Pin Interrupts Ports P, H and J offer pin interrupt capability. The interrupt enable as well as the sensitivity to rising or falling edges can be individually configured on per-pin basis. All bits/pins in a port share the same interrupt vector. Interrupts can be used with the pins configured as inputs or outputs. An interrupt is generated when a bit in the port interrupt flag register and its corresponding port interrupt enable bit are both set. The pin interrupt feature is also capable to wake up the CPU when it is in STOP or WAIT mode. A digital filter on each pin prevents pulses (Figure 24-70) shorter than a specified time from generating an interrupt. The minimum time varies over process conditions, temperature and voltage (Figure 24-69 and Table 24-62). Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) Glitch, filtered out, no interrupt flag set Valid pulse, interrupt flag set uncertain tpign tpval Figure 24-69. Interrupt Glitch Filter on Port P, H, and J (PPS = 0) Table 24-62. Pulse Detection Criteria Mode Pulse STOP Unit STOP1 Ignored tpulse 3 Bus clocks tpulse tpign Uncertain 3 < tpulse < 4 Bus clocks tpign < tpulse < tpval Valid tpulse 4 Bus clocks tpulse tpval 1. These values include the spread of the oscillator frequency over temperature, voltage and process. tpulse Figure 24-70. Pulse Illustration A valid edge on an input is detected if 4 consecutive samples of a passive level are followed by 4 consecutive samples of an active level directly or indirectly. The filters are continuously clocked by the bus clock in run and wait mode. In stop mode, the clock is generated by an RC-oscillator in the port integration module. To maximize current saving the RC oscillator runs only if the following condition is true on any pin individually: Sample count <= 4 and interrupt enabled (PIE = 1) and interrupt flag not set (PIF = 0). 24.0.9 24.0.9.1 Low-Power Options Run Mode No low-power options exist for this module in run mode. MC9S12XDP512 Data Sheet, Rev. 2.21 1034 Freescale Semiconductor 24.0.9.2 Wait Mode No low-power options exist for this module in wait mode. 24.0.9.3 Stop Mode All clocks are stopped. There are asynchronous paths to generate interrupts from stop on port P, H, and J. Initialization and Application Information * It is not recommended to write PORTx and DDRx in a word access. When changing the register pins from inputs to outputs, the data may have extra transitions during the write access. Initialize the port data register before enabling the outputs. * Power consumption will increase the more the voltages on general purpose input pins deviate from the supply voltages towards mid-range because the digital input buffers operate in the linear region. Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 1036 Freescale Semiconductor Chapter 24 DG128 Port Integration Module (S12XDG128PIMV2) MC9S12XDP512 Data Sheet, Rev. 2.21 1038 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.1 Introduction This document describes the EETX2K module which includes a 2Kbyte EEPROM (nonvolatile) memory. The EEPROM memory may be read as either bytes, aligned words, or misaligned words. Read access time is one bus cycle for bytes and aligned words, and two bus cycles for misaligned words. The EEPROM memory is ideal for data storage for single-supply applications allowing for field reprogramming without requiring external voltage sources for program or erase. Program and erase functions are controlled by a command driven interface. The EEPROM module supports both block erase (all memory bytes) and sector erase (4 memory bytes). An erased bit reads 1 and a programmed bit reads 0. The high voltage required to program and erase the EEPROM memory is generated internally. It is not possible to read from the EEPROM block while it is being erased or programmed. CAUTION An EEPROM word (2 bytes) must be in the erased state before being programmed. Cumulative programming of bits within a word is not allowed. 25.1.1 Glossary Command Write Sequence -- A three-step MCU instruction sequence to execute built-in algorithms (including program and erase) on the EEPROM memory. 25.1.2 * * * * * * * * Features 2 Kbytes of EEPROM memory divided into 512 sectors of 4 bytes Automated program and erase algorithm Interrupts on EEPROM command completion and command buffer empty Fast sector erase and word program operation 2-stage command pipeline Sector erase abort feature for critical interrupt response Flexible protection scheme to prevent accidental program or erase Single power supply for all EEPROM operations including program and erase 25.1.3 Modes of Operation Program, erase and erase verify operations (please refer to Section 25.4.1, "EEPROM Command Operations" for details). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1039 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.1.4 Block Diagram A block diagram of the EEPROM module is shown in Figure 25-1. EETX2K EEPROM Interface Command Interrupt Request Command Pipeline EEPROM cmd2 addr2 data2 cmd1 addr1 data1 Registers 1K * 16 Bits sector 0 sector 1 Protection sector 511 Oscillator Clock Clock Divider EECLK Figure 25-1. EETX2K Block Diagram 25.2 External Signal Description The EEPROM module contains no signals that connect off-chip. 25.3 Memory Map and Register Definition This section describes the memory map and registers for the EEPROM module. 25.3.1 Module Memory Map The EEPROM memory map is shown in Figure 25-2. The HCS12X architecture places the EEPROM memory addresses between global addresses 0x13_F800 and 0x13_FFFF. The EPROT register, described in Section 25.3.2.5, "EEPROM Protection Register (EPROT)", can be set to protect the upper region in the EEPROM memory from accidental program or erase. The EEPROM addresses covered by this protectable MC9S12XDP512 Data Sheet, Rev. 2.21 1040 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) region are shown in the EEPROM memory map. The default protection setting is stored in the EEPROM configuration field as described in Table 25-1. Table 25-1. EEPROM Configuration Field Global Address Size (bytes) Description 0x13_FFFC 1 Reserved 0x13_FFFD 1 EEPROM Protection byte Refer to Section 25.3.2.5, "EEPROM Protection Register (EPROT)" 0x13_FFFE - 0x13_FFFF 2 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1041 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) MODULE BASE + 0x0000 MODULE BASE + 0x000B EEPROM Registers 12 bytes EEPROM START = 0x13_F800 EEPROM Memory 1536 bytes (up to 1984 bytes) 0x13_FE00 0x13_FE40 0x13_FE80 0x13_FEC0 0x13_FF00 EEPROM Memory Protected Region 64, 128, 192, 256, 320, 384, 448, or 512 bytes 0x13_FF40 0x13_FF80 0x13_FFC0 EEPROM END = 0x13_FFFF EEPROM Configuration Field 4 bytes (0x13_FFFC - 0x13_FFFF) Figure 25-2. EEPROM Memory Map MC9S12XDP512 Data Sheet, Rev. 2.21 1042 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.3.2 Register Descriptions The EEPROM module also contains a set of 12 control and status registers located between EEPROM module base + 0x0000 and 0x000B. A summary of the EEPROM module registers is given in Figure 25-3. Detailed descriptions of each register bit are provided. Register Name ECLKDIV Bit 7 R 6 5 4 3 2 1 Bit 0 PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CBEIE CCIE 0 0 0 0 0 0 RNV5 RNV4 EPDIS EPS2 EPS1 EPS0 PVIOL ACCERR 0 BLANK 0 0 0 0 EDIVLD W RESERVED1 R W RESERVED2 R W ECNFG R W EPROT R W ESTAT R W ECMD EPOPEN CBEIF R RNV6 CCIF 0 CMDB W RESERVED3 R 0 0 0 0 0 0 0 0 0 0 0 0 W EADDRHI R EABHI W EADDRLO R EABLO W EDATAHI R EDHI W EDATALO R EDLO W = Unimplemented or Reserved Figure 25-3. EETX2K Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1043 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.3.2.1 EEPROM Clock Divider Register (ECLKDIV) The ECLKDIV register is used to control timed events in program and erase algorithms. 7 R 6 5 4 3 2 1 0 PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0 0 0 0 0 0 0 0 EDIVLD W Reset 0 = Unimplemented or Reserved Figure 25-4. EEPROM Clock Divider Register (ECLKDIV) All bits in the ECLKDIV register are readable, bits 6-0 are write once and bit 7 is not writable. Table 25-2. ECLKDIV Field Descriptions Field Description 7 EDIVLD Clock Divider Loaded 0 Register has not been written. 1 Register has been written to since the last reset. 6 PRDIV8 Enable Prescalar by 8 0 The oscillator clock is directly fed into the ECLKDIV divider. 1 Enables a Prescalar by 8, to divide the oscillator clock before feeding into the clock divider. 5:0 EDIV[5:0] 25.3.2.2 Clock Divider Bits -- The combination of PRDIV8 and EDIV[5:0] effectively divides the EEPROM module input oscillator clock down to a frequency of 150 kHz - 200 kHz. The maximum divide ratio is 512. Please refer to Section 25.4.1.1, "Writing the ECLKDIV Register" for more information. RESERVED1 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 25-5. RESERVED1 All bits read 0 and are not writable. 25.3.2.3 RESERVED2 This register is reserved for factory testing and is not accessible. MC9S12XDP512 Data Sheet, Rev. 2.21 1044 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 25-6. RESERVED2 All bits read 0 and are not writable. 25.3.2.4 EEPROM Configuration Register (ECNFG) The ECNFG register enables the EEPROM interrupts. 7 6 CBEIE CCIE 0 0 R 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 25-7. EEPROM Configuration Register (ECNFG) CBEIE and CCIE bits are readable and writable while all remaining bits read 0 and are not writable. Table 25-3. ECNFG Field Descriptions Field Description 7 CBEIE Command Buffer Empty Interrupt Enable -- The CBEIE bit enables an interrupt in case of an empty command buffer in the EEPROM module. 0 Command Buffer Empty interrupt disabled. 1 An interrupt will be requested whenever the CBEIF flag (see Section 25.3.2.6, "EEPROM Status Register (ESTAT)") is set. 6 CCIE Command Complete Interrupt Enable -- The CCIE bit enables an interrupt in case all commands have been completed in the EEPROM module. 0 Command Complete interrupt disabled. 1 An interrupt will be requested whenever the CCIF flag (see Section 25.3.2.6, "EEPROM Status Register (ESTAT)") is set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1045 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.3.2.5 EEPROM Protection Register (EPROT) The EPROT register defines which EEPROM sectors are protected against program or erase operations. 7 R 6 5 4 RNV6 RNV5 RNV4 EPOPEN 3 2 1 0 EPDIS EPS2 EPS1 EPS0 F F F F W Reset F F F F = Unimplemented or Reserved Figure 25-8. EEPROM Protection Register (EPROT) During the reset sequence, the EPROT register is loaded from the EEPROM Protection byte at address offset 0x0FFD (see Table 25-1).All bits in the EPROT register are readable and writable except for RNV[6:4] which are only readable. The EPOPEN and EPDIS bits can only be written to the protected state. The EPS bits can be written anytime until bit EPDIS is cleared. If the EPOPEN bit is cleared, the state of the EPDIS and EPS bits is irrelevant. To change the EEPROM protection that will be loaded during the reset sequence, the EEPROM memory must be unprotected, then the EEPROM Protection byte must be reprogrammed. Trying to alter data in any protected area in the EEPROM memory will result in a protection violation error and the PVIOL flag will be set in the ESTAT register. The mass erase of an EEPROM block is possible only when protection is fully disabled by setting the EPOPEN and EPDIS bits. Table 25-4. EPROT Field Descriptions Field Description 7 EPOPEN Opens the EEPROM for Program or Erase 0 The entire EEPROM memory is protected from program and erase. 1 The EEPROM sectors not protected are enabled for program or erase. 6:4 RNV[6:4] Reserved Nonvolatile Bits -- The RNV[6:4] bits should remain in the erased state "1" for future enhancements. 3 EPDIS EEPROM Protection Address Range Disable -- The EPDIS bit determines whether there is a protected area in a specific region of the EEPROM memory ending with address offset 0x0FFF. 0 Protection enabled. 1 Protection disabled. 2:0 EPS[2:0] EEPROM Protection Address Size -- The EPS[2:0] bits determine the size of the protected area as shown inTable 25-5. The EPS bits can only be written to while the EPDIS bit is set. MC9S12XDP512 Data Sheet, Rev. 2.21 1046 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) Table 25-5. EEPROM Protection Address Range 25.3.2.6 EPS[2:0] Address Offset Range Protected Size 000 0x0FC0 - 0x0FFF 64 bytes 001 0x0F80 - 0x0FFF 128 bytes 010 0x0F40 - 0x0FFF 192 bytes 011 0x0F00 - 0x0FFF 256 bytes 100 0x0EC0 - 0x0FFF 320 bytes 101 0x0E80 - 0x0FFF 384 bytes 110 0x0E40 - 0x0FFF 448 bytes 111 0x0E00 - 0x0FFF 512 bytes EEPROM Status Register (ESTAT) The ESTAT register defines the operational status of the module. 7 6 R 5 4 CCIF CBEIF PVIOL ACCERR 0 0 3 2 1 0 0 BLANK 0 0 0 0 0 0 W Reset 1 1 = Unimplemented or Reserved Figure 25-9. EEPROM Status Register (ESTAT -- Normal Mode) 7 6 R 5 4 CCIF CBEIF PVIOL ACCERR 0 0 3 2 0 BLANK 1 0 0 FAIL W Reset 1 1 0 0 0 0 = Unimplemented or Reserved Figure 25-10. EEPROM Status Register (ESTAT -- Special Mode) CBEIF, PVIOL, and ACCERR are readable and writable, CCIF and BLANK are readable and not writable, remaining bits read 0 and are not writable in normal mode. FAIL is readable and writable in special mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1047 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) Table 25-6. ESTAT Field Descriptions Field Description 7 CBEIF Command Buffer Empty Interrupt Flag -- The CBEIF flag indicates that the address, data, and command buffers are empty so that a new command write sequence can be started. The CBEIF flag is cleared by writing a 1 to CBEIF. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned word to the EEPROM address space but before CBEIF is cleared will abort a command write sequence and cause the ACCERR flag to be set. Writing a 0 to CBEIF outside of a command write sequence will not set the ACCERR flag. The CBEIF flag is used together with the CBEIE bit in the ECNFG register to generate an interrupt request (see Figure 25-24). 0 Buffers are full. 1 Buffers are ready to accept a new command. 6 CCIF Command Complete Interrupt Flag -- The CCIF flag indicates that there are no more commands pending. The CCIF flag is cleared when CBEIF is clear and sets automatically upon completion of all active and pending commands. The CCIF flag does not set when an active commands completes and a pending command is fetched from the command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together with the CCIE bit in the ECNFG register to generate an interrupt request (see Figure 25-24). 0 Command in progress. 1 All commands are completed. 5 PVIOL Protection Violation Flag -- The PVIOL flag indicates an attempt was made to program or erase an address in a protected area of the EEPROM memory during a command write sequence. The PVIOL flag is cleared by writing a 1 to PVIOL. Writing a 0 to the PVIOL flag has no effect on PVIOL. While PVIOL is set, it is not possible to launch a command or start a command write sequence. 0 No failure. 1 A protection violation has occurred. 4 ACCERR Access Error Flag -- The ACCERR flag indicates an illegal access has occurred to the EEPROM memory caused by either a violation of the command write sequence (see Section 25.4.1.2, "Command Write Sequence"), issuing an illegal EEPROM command (see Table 25-8), launching the sector erase abort command terminating a sector erase operation early (see Section 25.4.2.5, "Sector Erase Abort Command") or the execution of a CPU STOP instruction while a command is executing (CCIF = 0). The ACCERR flag is cleared by writing a 1 to ACCERR. Writing a 0 to the ACCERR flag has no effect on ACCERR. While ACCERR is set, it is not possible to launch a command or start a command write sequence. If ACCERR is set by an erase verify operation, any buffered command will not launch. 0 No access error detected. 1 Access error has occurred. 2 BLANK Flag Indicating the Erase Verify Operation Status -- When the CCIF flag is set after completion of an erase verify command, the BLANK flag indicates the result of the erase verify operation. The BLANK flag is cleared by the EEPROM module when CBEIF is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect on BLANK. 0 EEPROM block verified as not erased. 1 EEPROM block verified as erased. 1 FAIL Flag Indicating a Failed EEPROM Operation -- The FAIL flag will set if the erase verify operation fails (EEPROM block verified as not erased). The FAIL flag is cleared by writing a 1 to FAIL. Writing a 0 to the FAIL flag has no effect on FAIL. 0 EEPROM operation completed without error. 1 EEPROM operation failed. MC9S12XDP512 Data Sheet, Rev. 2.21 1048 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.3.2.7 EEPROM Command Register (ECMD) The ECMD register is the EEPROM command register. 7 R 6 5 4 3 2 1 0 0 0 0 0 CMDB W Reset 0 0 0 0 0 = Unimplemented or Reserved Figure 25-11. EEPROM Command Register (ECMD) All CMDB bits are readable and writable during a command write sequence while bit 7 reads 0 and is not writable. Table 25-7. ECMD Field Descriptions Field Description 6:0 CMDB[6:0] EEPROM Command Bits -- Valid EEPROM commands are shown in Table 25-8. Writing any command other than those listed in Table 25-8 sets the ACCERR flag in the ESTAT register. Table 25-8. Valid EEPROM Command List 25.3.2.8 CMDB[6:0] Command 0x05 Erase Verify 0x20 Word Program 0x40 Sector Erase 0x41 Mass Erase 0x47 Sector Erase Abort 0x60 Sector Modify RESERVED3 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 25-12. RESERVED3 All bits read 0 and are not writable. EEPROM Address Registers (EADDR) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1049 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) The EADDRHI and EADDRLO registers are the EEPROM address registers. R 7 6 5 4 3 2 0 0 0 0 0 0 0 0 0 0 0 0 1 0 EABHI W Reset 0 0 = Unimplemented or Reserved Figure 25-13. EEPROM Address High Register (EADDRHI) 7 6 5 4 R 3 2 1 0 0 0 0 0 EABLO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 25-14. EEPROM Address Low Register (EADDRLO) All EABHI and EABLO bits read 0 and are not writable in normal modes. All EABHI and EABLO bits are readable and writable in special modes. The MCU address bit AB0 is not stored in the EADDR registers since the EEPROM block is not byte addressable. 25.3.2.9 EEPROM Data Registers (EDATA) The EDATAHI and EDATALO registers are the EEPROM data registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 EDHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 25-15. EEPROM Data High Register (EDATAHI) 7 6 5 4 R 3 2 1 0 0 0 0 0 EDLO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 25-16. EEPROM Data Low Register (EDATALO) All EDHI and EDLO bits read 0 and are not writable in normal modes. MC9S12XDP512 Data Sheet, Rev. 2.21 1050 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) All EDHI and EDLO bits are readable and writable in special modes. 25.4 Functional Description 25.4.1 EEPROM Command Operations Write operations are used to execute program, erase, erase verify, sector erase abort, and sector modify algorithms described in this section. The program, erase, and sector modify algorithms are controlled by a state machine whose timebase, EECLK, is derived from the oscillator clock via a programmable divider. The command register as well as the associated address and data registers operate as a buffer and a register (2-stage FIFO) so that a second command along with the necessary data and address can be stored to the buffer while the first command is still in progress. Buffer empty as well as command completion are signalled by flags in the EEPROM status register with interrupts generated, if enabled. The next sections describe: 1. How to write the ECLKDIV register 2. Command write sequences to program, erase, erase verify, sector erase abort, and sector modify operations on the EEPROM memory 3. Valid EEPROM commands 4. Effects resulting from illegal EEPROM command write sequences or aborting EEPROM operations 25.4.1.1 Writing the ECLKDIV Register Prior to issuing any EEPROM command after a reset, the user is required to write the ECLKDIV register to divide the oscillator clock down to within the 150 kHz to 200 kHz range. Since the program and erase timings are also a function of the bus clock, the ECLKDIV determination must take this information into account. If we define: * ECLK as the clock of the EEPROM timing control block * Tbus as the period of the bus clock * INT(x) as taking the integer part of x (e.g., INT(4.323)=4) then ECLKDIV register bits PRDIV8 and EDIV[5:0] are to be set as described in Figure 25-17. For example, if the oscillator clock frequency is 950 kHz and the bus clock frequency is 10 MHz, ECLKDIV bits EDIV[5:0] should be set to 0x04 (000100) and bit PRDIV8 set to 0. The resulting EECLK frequency is then 190 kHz. As a result, the EEPROM program and erase algorithm timings are increased over the optimum target by: ( 200 - 190 ) 200 x 100 = 5% If the oscillator clock frequency is 16 MHz and the bus clock frequency is 40 MHz, ECLKDIV bits EDIV[5:0] should be set to 0x0A (001010) and bit PRDIV8 set to 1. The resulting EECLK frequency is MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1051 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) then 182 kHz. In this case, the EEPROM program and erase algorithm timings are increased over the optimum target by: ( 200 - 182 ) 200 x 100 = 9% CAUTION Program and erase command execution time will increase proportionally with the period of EECLK. Because of the impact of clock synchronization on the accuracy of the functional timings, programming or erasing the EEPROM memory cannot be performed if the bus clock runs at less than 1 MHz. Programming or erasing the EEPROM memory with EECLK < 150 kHz should be avoided. Setting ECLKDIV to a value such that EECLK < 150 kHz can destroy the EEPROM memory due to overstress. Setting ECLKDIV to a value such that (1/EECLK+Tbus) < 5 s can result in incomplete programming or erasure of the EEPROM memory cells. If the ECLKDIV register is written, the EDIVLD bit is set automatically. If the EDIVLD bit is 0, the ECLKDIV register has not been written since the last reset. If the ECLKDIV register has not been written to, the EEPROM command loaded during a command write sequence will not execute and the ACCERR flag in the ESTAT register will set. MC9S12XDP512 Data Sheet, Rev. 2.21 1052 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) START Tbus < 1s? no ALL COMMANDS IMPOSSIBLE yes PRDIV8 = 0 (reset) oscillator_clock >12.8 MHz? no yes PRDIV8 = 1 PRDCLK = oscillator_clock/8 PRDCLK = oscillator_clock PRDCLK[MHz]*(5+Tbus[s]) an integer? yes no EDIV[5:0]=INT(PRDCLK[MHz]*(5+Tbus[s])) EDIV[5:0]=PRDCLK[MHz]*(5+Tbus[s])-1 TRY TO DECREASE Tbus EECLK = (PRDCLK)/(1+EDIV[5:0]) 1/EECLK[MHz] + Tbus[ms] > 5 AND EECLK > 0.15 MHz ? yes END no yes EDIV[5:0] > 4? no ALL COMMANDS IMPOSSIBLE Figure 25-17. Determination Procedure for PRDIV8 and EDIV Bits MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1053 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.1.2 Command Write Sequence The EEPROM command controller is used to supervise the command write sequence to execute program, erase, erase verify, sector erase abort, and sector modify algorithms. Before starting a command write sequence, the ACCERR and PVIOL flags in the ESTAT register must be clear (see Section 25.3.2.6, "EEPROM Status Register (ESTAT)") and the CBEIF flag should be tested to determine the state of the address, data and command buffers. If the CBEIF flag is set, indicating the buffers are empty, a new command write sequence can be started. If the CBEIF flag is clear, indicating the buffers are not available, a new command write sequence will overwrite the contents of the address, data and command buffers. A command write sequence consists of three steps which must be strictly adhered to with writes to the EEPROM module not permitted between the steps. However, EEPROM register and array reads are allowed during a command write sequence. The basic command write sequence is as follows: 1. Write to one address in the EEPROM memory. 2. Write a valid command to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the command. The address written in step 1 will be stored in the EADDR registers and the data will be stored in the EDATA registers. If the CBEIF flag in the ESTAT register is clear when the first EEPROM array write occurs, the contents of the address and data buffers will be overwritten and the CBEIF flag will be set. When the CBEIF flag is cleared, the CCIF flag is cleared on the same bus cycle by the EEPROM command controller indicating that the command was successfully launched. For all command write sequences except sector erase abort, the CBEIF flag will set four bus cycles after the CCIF flag is cleared indicating that the address, data, and command buffers are ready for a new command write sequence to begin. For sector erase abort operations, the CBEIF flag will remain clear until the operation completes. Except for the sector erase abort command, a buffered command will wait for the active operation to be completed before being launched. The sector erase abort command is launched when the CBEIF flag is cleared as part of a sector erase abort command write sequence. Once a command is launched, the completion of the command operation is indicated by the setting of the CCIF flag in the ESTAT register. The CCIF flag will set upon completion of all active and buffered commands. 25.4.2 EEPROM Commands Table 25-9 summarizes the valid EEPROM commands along with the effects of the commands on the EEPROM block. Table 25-9. EEPROM Command Description ECMDB Command Function on EEPROM Memory 0x05 Erase Verify Verify all memory bytes in the EEPROM block are erased. If the EEPROM block is erased, the BLANK flag in the ESTAT register will set upon command completion. 0x20 Program 0x40 Sector Erase Program a word (two bytes) in the EEPROM block. Erase all four memory bytes in a sector of the EEPROM block. MC9S12XDP512 Data Sheet, Rev. 2.21 1054 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) Table 25-9. EEPROM Command Description ECMDB Command Function on EEPROM Memory 0x41 Mass Erase Erase all memory bytes in the EEPROM block. A mass erase of the full EEPROM block is only possible when EPOPEN and EPDIS bits in the EPROT register are set prior to launching the command. 0x47 Sector Erase Abort Abort the sector erase operation. The sector erase operation will terminate according to a set procedure. The EEPROM sector should not be considered erased if the ACCERR flag is set upon command completion. 0x60 Sector Modify Erase all four memory bytes in a sector of the EEPROM block and reprogram the addressed word. CAUTION An EEPROM word (2 bytes) must be in the erased state before being programmed. Cumulative programming of bits within a word is not allowed. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1055 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.2.1 Erase Verify Command The erase verify operation will verify that the EEPROM memory is erased. An example flow to execute the erase verify operation is shown in Figure 25-18. The erase verify command write sequence is as follows: 1. Write to an EEPROM address to start the command write sequence for the erase verify command. The address and data written will be ignored. 2. Write the erase verify command, 0x05, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the erase verify command. After launching the erase verify command, the CCIF flag in the ESTAT register will set after the operation has completed unless a new command write sequence has been buffered. The number of bus cycles required to execute the erase verify operation is equal to the number of words in the EEPROM memory plus 14 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Upon completion of the erase verify operation, the BLANK flag in the ESTAT register will be set if all addresses in the EEPROM memory are verified to be erased. If any address in the EEPROM memory is not erased, the erase verify operation will terminate and the BLANK flag in the ESTAT register will remain clear. MC9S12XDP512 Data Sheet, Rev. 2.21 1056 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Address and Dummy Data 2. Write: ECMD register Erase Verify Command 0x05 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes Erase Verify Status BLANK Set? no yes EXIT EEPROM Memory Erased EXIT EEPROM Memory Not Erased Figure 25-18. Example Erase Verify Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1057 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.2.2 Program Command The program operation will program a previously erased word in the EEPROM memory using an embedded algorithm. An example flow to execute the program operation is shown in Figure 25-19. The program command write sequence is as follows: 1. Write to an EEPROM block address to start the command write sequence for the program command. The data written will be programmed to the address written. 2. Write the program command, 0x20, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the program command. If a word to be programmed is in a protected area of the EEPROM memory, the PVIOL flag in the ESTAT register will set and the program command will not launch. Once the program command has successfully launched, the CCIF flag in the ESTAT register will set after the program operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1058 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check 1. Write: EEPROM Address and program Data 2. Write: ECMD register Program Command 0x20 3. Write: ESTAT register Clear CBEIF 0x80 yes Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Buffer Empty Check no CBEIF Set? yes Sequential Programming Decision Next Word? yes no Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 25-19. Example Program Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1059 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.2.3 Sector Erase Command The sector erase operation will erase both words in a sector of EEPROM memory using an embedded algorithm. An example flow to execute the sector erase operation is shown in Figure 25-20. The sector erase command write sequence is as follows: 1. Write to an EEPROM memory address to start the command write sequence for the sector erase command. The EEPROM address written determines the sector to be erased while global address bits [1:0] and the data written are ignored. 2. Write the sector erase command, 0x40, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the sector erase command. If an EEPROM sector to be erased is in a protected area of the EEPROM memory, the PVIOL flag in the ESTAT register will set and the sector erase command will not launch. Once the sector erase command has successfully launched, the CCIF flag in the ESTAT register will set after the sector erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1060 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Sector Address and Dummy Data 2. Write: ECMD register Sector Erase Command 0x40 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 25-20. Example Sector Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1061 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.2.4 Mass Erase Command The mass erase operation will erase all addresses in an EEPROM block using an embedded algorithm. An example flow to execute the mass erase operation is shown in Figure 25-21. The mass erase command write sequence is as follows: 1. Write to an EEPROM memory address to start the command write sequence for the mass erase command. The address and data written will be ignored. 2. Write the mass erase command, 0x41, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the mass erase command. If the EEPROM memory to be erased contains any protected area, the PVIOL flag in the ESTAT register will set and the mass erase command will not launch. Once the mass erase command has successfully launched, the CCIF flag in the ESTAT register will set after the mass erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1062 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Address and Dummy Data 2. Write: ECMD register Mass Erase Command 0x41 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 25-21. Example Mass Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1063 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.2.5 Sector Erase Abort Command The sector erase abort operation will terminate the active sector erase or sector modify operation so that other sectors in an EEPROM block are available for read and program operations without waiting for the sector erase or sector modify operation to complete. An example flow to execute the sector erase abort operation is shown in Figure 25-22. The sector erase abort command write sequence is as follows: 1. Write to any EEPROM memory address to start the command write sequence for the sector erase abort command. The address and data written are ignored. 2. Write the sector erase abort command, 0x47, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the sector erase abort command. If the sector erase abort command is launched resulting in the early termination of an active sector erase or sector modify operation, the ACCERR flag will set once the operation completes as indicated by the CCIF flag being set. The ACCERR flag sets to inform the user that the EEPROM sector may not be fully erased and a new sector erase or sector modify command must be launched before programming any location in that specific sector. If the sector erase abort command is launched but the active sector erase or sector modify operation completes normally, the ACCERR flag will not set upon completion of the operation as indicated by the CCIF flag being set. If the sector erase abort command is launched after the sector modify operation has completed the sector erase step, the program step will be allowed to complete. The maximum number of cycles required to abort a sector erase or sector modify operation is equal to four EECLK periods (see Section 25.4.1.1, "Writing the ECLKDIV Register") plus five bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. NOTE Since the ACCERR bit in the ESTAT register may be set at the completion of the sector erase abort operation, a command write sequence is not allowed to be buffered behind a sector erase abort command write sequence. The CBEIF flag will not set after launching the sector erase abort command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a sector erase abort operation active, the ACCERR flag in the ESTAT register will be set. A new command write sequence may be started after clearing the ACCERR flag, if set. NOTE The sector erase abort command should be used sparingly since a sector erase operation that is aborted counts as a complete program/erase cycle. MC9S12XDP512 Data Sheet, Rev. 2.21 1064 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) Execute Sector Erase/Modify Command Flow Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? Erase Abort Needed? no yes Sector Erase Completed no yes EXIT 1. Write: Dummy EEPROM Address and Dummy Data NOTE: command write sequence aborted by writing 0x00 to ESTAT register. 2. Write: ECMD register Sector Erase Abort Cmd 0x47 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. 3. Write: ESTAT register Clear CBEIF 0x80 Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes Access Error Check ACCERR Set? yes Write: ESTAT register Clear ACCERR 0x10 no Sector Erase or Modify Completed EXIT Sector Erase or Modify Aborted EXIT Figure 25-22. Example Sector Erase Abort Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1065 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.2.6 Sector Modify Command The sector modify operation will erase both words in a sector of EEPROM memory followed by a reprogram of the addressed word using an embedded algorithm. An example flow to execute the sector modify operation is shown in Figure 25-23. The sector modify command write sequence is as follows: 1. Write to an EEPROM memory address to start the command write sequence for the sector modify command. The EEPROM address written determines the sector to be erased and word to be reprogrammed while byte address bit 0 is ignored. 2. Write the sector modify command, 0x60, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the sector erase command. If an EEPROM sector to be modified is in a protected area of the EEPROM memory, the PVIOL flag in the ESTAT register will set and the sector modify command will not launch. Once the sector modify command has successfully launched, the CCIF flag in the ESTAT register will set after the sector modify operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1066 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Word Address and program Data 2. Write: ECMD register Sector Modify Command 0x60 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 25-23. Example Sector Modify Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1067 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.4.3 Illegal EEPROM Operations The ACCERR flag will be set during the command write sequence if any of the following illegal steps are performed, causing the command write sequence to immediately abort: 1. Writing to an EEPROM address before initializing the ECLKDIV register. 2. Writing a byte or misaligned word to a valid EEPROM address. 3. Starting a command write sequence while a sector erase abort operation is active. 4. Writing to any EEPROM register other than ECMD after writing to an EEPROM address. 5. Writing a second command to the ECMD register in the same command write sequence. 6. Writing an invalid command to the ECMD register. 7. Writing to an EEPROM address after writing to the ECMD register. 8. Writing to any EEPROM register other than ESTAT (to clear CBEIF) after writing to the ECMD register. 9. Writing a 0 to the CBEIF flag in the ESTAT register to abort a command write sequence. The ACCERR flag will not be set if any EEPROM register is read during a valid command write sequence. The ACCERR flag will also be set if any of the following events occur: 1. Launching the sector erase abort command while a sector erase or sector modify operation is active which results in the early termination of the sector erase or sector modify operation (see Section 25.4.2.5, "Sector Erase Abort Command"). 2. The MCU enters stop mode and a command operation is in progress. The operation is aborted immediately and any pending command is purged (see Section 25.5.2, "Stop Mode"). If the EEPROM memory is read during execution of an algorithm (CCIF = 0), the read operation will return invalid data and the ACCERR flag will not be set. If the ACCERR flag is set in the ESTAT register, the user must clear the ACCERR flag before starting another command write sequence (see Section 25.3.2.6, "EEPROM Status Register (ESTAT)"). The PVIOL flag will be set after the command is written to the ECMD register during a command write sequence if any of the following illegal operations are attempted, causing the command write sequence to immediately abort: 1. Writing the program command if the address written in the command write sequence was in a protected area of the EEPROM memory. 2. Writing the sector erase command if the address written in the command write sequence was in a protected area of the EEPROM memory. 3. Writing the mass erase command to the EEPROM memory while any EEPROM protection is enabled. 4. Writing the sector modify command if the address written in the command write sequence was in a protected area of the EEPROM memory. If the PVIOL flag is set in the ESTAT register, the user must clear the PVIOL flag before starting another command write sequence (see Section 25.3.2.6, "EEPROM Status Register (ESTAT)"). MC9S12XDP512 Data Sheet, Rev. 2.21 1068 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.5 25.5.1 Operating Modes Wait Mode If a command is active (CCIF = 0) when the MCU enters the wait mode, the active command and any buffered command will be completed. The EEPROM module can recover the MCU from wait mode if the CBEIF and CCIF interrupts are enabled (see Section 25.8, "Interrupts"). 25.5.2 Stop Mode If a command is active (CCIF = 0) when the MCU enters the stop mode, the operation will be aborted and, if the operation is program, sector erase, mass erase, or sector modify, the EEPROM array data being programmed or erased may be corrupted and the CCIF and ACCERR flags will be set. If active, the high voltage circuitry to the EEPROM memory will immediately be switched off when entering stop mode. Upon exit from stop mode, the CBEIF flag is set and any buffered command will not be launched. The ACCERR flag must be cleared before starting a command write sequence (see Section 25.4.1.2, "Command Write Sequence"). NOTE As active commands are immediately aborted when the MCU enters stop mode, it is strongly recommended that the user does not use the STOP instruction during program, sector erase, mass erase, or sector modify operations. 25.5.3 Background Debug Mode In background debug mode (BDM), the EPROT register is writable. If the MCU is unsecured, then all EEPROM commands listed in Table 25-9 can be executed. If the MCU is secured and is in special single chip mode, the only command available to execute is mass erase. 25.6 EEPROM Module Security The EEPROM module does not provide any security information to the MCU. After each reset, the security state of the MCU is a function of information provided by the Flash module (see the specific FTX Block Guide). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1069 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.6.1 Unsecuring the MCU in Special Single Chip Mode using BDM Before the MCU can be unsecured in special single chip mode, the EEPROM memory must be erased using the following method : * Reset the MCU into special single chip mode, delay while the erase test is performed by the BDM secure ROM, send BDM commands to disable protection in the EEPROM module, and execute a mass erase command write sequence to erase the EEPROM memory. After the CCIF flag sets to indicate that the EEPROM mass operation has completed and assuming that the Flash memory has also been erased, reset the MCU into special single chip mode. The BDM secure ROM will verify that the Flash and EEPROM memory are erased and will assert the UNSEC bit in the BDM status register. This BDM action will cause the MCU to override the Flash security state and the MCU will be unsecured. Once the MCU is unsecured, BDM commands will be enabled and the Flash security byte may be programmed to the unsecure state. 25.7 25.7.1 Resets EEPROM Reset Sequence On each reset, the EEPROM module executes a reset sequence to hold CPU activity while loading the EPROT register from the EEPROM memory according to Table 25-1. 25.7.2 Reset While EEPROM Command Active If a reset occurs while any EEPROM command is in progress, that command will be immediately aborted. The state of a word being programmed or the sector / block being erased is not guaranteed. 25.8 Interrupts The EEPROM module can generate an interrupt when all EEPROM command operations have completed, when the EEPROM address, data, and command buffers are empty. Table 25-10. EEPROM Interrupt Sources Interrupt Source Interrupt Flag Local Enable Global (CCR) Mask EEPROM address, data, and command buffers empty CBEIF (ESTAT register) CBEIE (ECNFG register) I Bit All EEPROM commands completed CCIF (ESTAT register) CCIE (ECNFG register) I Bit NOTE Vector addresses and their relative interrupt priority are determined at the MCU level. MC9S12XDP512 Data Sheet, Rev. 2.21 1070 Freescale Semiconductor Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) 25.8.1 Description of EEPROM Interrupt Operation The logic used for generating interrupts is shown in Figure 25-24. The EEPROM module uses the CBEIF and CCIF flags in combination with the CBIE and CCIE enable bits to generate the EEPROM command interrupt request. CBEIF CBEIE EEPROM Command Interrupt Request CCIF CCIE Figure 25-24. EEPROM Interrupt Implementation For a detailed description of the register bits, refer to Section 25.3.2.4, "EEPROM Configuration Register (ECNFG)" and Section 25.3.2.6, "EEPROM Status Register (ESTAT)" . MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1071 Chapter 25 2 Kbyte EEPROM Module (S12XEETX2KV1) MC9S12XDP512 Data Sheet, Rev. 2.21 1072 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.1 Introduction This document describes the EETX4K module which includes a 4 Kbyte EEPROM (nonvolatile) memory. The EEPROM memory may be read as either bytes, aligned words, or misaligned words. Read access time is one bus cycle for bytes and aligned words, and two bus cycles for misaligned words. The EEPROM memory is ideal for data storage for single-supply applications allowing for field reprogramming without requiring external voltage sources for program or erase. Program and erase functions are controlled by a command driven interface. The EEPROM module supports both block erase (all memory bytes) and sector erase (4 memory bytes). An erased bit reads 1 and a programmed bit reads 0. The high voltage required to program and erase the EEPROM memory is generated internally. It is not possible to read from the EEPROM block while it is being erased or programmed. CAUTION An EEPROM word (2 bytes) must be in the erased state before being programmed. Cumulative programming of bits within a word is not allowed. 26.1.1 Glossary Command Write Sequence -- A three-step MCU instruction sequence to execute built-in algorithms (including program and erase) on the EEPROM memory. 26.1.2 * * * * * * * * Features 4 Kbytes of EEPROM memory divided into 1024 sectors of 4 bytes Automated program and erase algorithm Interrupts on EEPROM command completion and command buffer empty Fast sector erase and word program operation 2-stage command pipeline Sector erase abort feature for critical interrupt response Flexible protection scheme to prevent accidental program or erase Single power supply for all EEPROM operations including program and erase 26.1.3 Modes of Operation Program, erase and erase verify operations (please refer to Section 26.4.1, "EEPROM Command Operations" for details). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1073 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.1.4 Block Diagram A block diagram of the EEPROM module is shown in Figure 26-1. EETX4K Command Interrupt Request EEPROM Interface Command Pipeline EEPROM cmd2 addr2 data2 cmd1 addr1 data1 Registers 2K * 16 Bits sector 0 sector 1 Protection sector 1023 Oscillator Clock Clock Divider EECLK Figure 26-1. EETX4K Block Diagram 26.2 External Signal Description The EEPROM module contains no signals that connect off-chip. 26.3 Memory Map and Register Definition This section describes the memory map and registers for the EEPROM module. 26.3.1 Module Memory Map The EEPROM memory map is shown in Figure 26-2. The HCS12X architecture places the EEPROM memory addresses between global addresses 0x13_F000 and 0x13_FFFF. The EPROT register, described in Section 26.3.2.5, "EEPROM Protection Register (EPROT)", can be set to protect the upper region in the EEPROM memory from accidental program or erase. The EEPROM addresses covered by this protectable MC9S12XDP512 Data Sheet, Rev. 2.21 1074 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) region are shown in the EEPROM memory map. The default protection setting is stored in the EEPROM configuration field as described in Table 26-1. Table 26-1. EEPROM Configuration Field Global Address Size (bytes) Description 0x13_FFFC 1 Reserved 0x13_FFFD 1 EEPROM Protection byte Refer to Section 26.3.2.5, "EEPROM Protection Register (EPROT)" 0x13_FFFE - 0x13_FFFF 2 Reserved MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1075 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) MODULE BASE+ 0x0000 EEPROM Registers 12 bytes MODULE BASE + 0x000B EEPROM START = 0x13_F000 EEPROM Memory 3584 bytes (up to 4032 bytes) 0x13_FE00 0x13_FE40 0x13_FE80 0x13_FEC0 0x13_FF00 EEPROM Memory Protected Region 64, 128, 192, 256, 320, 384, 448, 512 bytes 0x13_FF40 0x13_FF80 0x13_FFC0 EEPROM END = 0x13_FFFF EEPROM Configuration Field 4 bytes (0x13_FFFC - 0x13_FFFF) Figure 26-2. EEPROM Memory Map MC9S12XDP512 Data Sheet, Rev. 2.21 1076 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) The EEPROM module also contains a set of 12 control and status registers located between EEPROM module base + 0x0000 and 0x000B. A summary of the EEPROM module registers is given in Table 26-2 while their accessibility is detailed in Section 26.3.2, "Register Descriptions". Table 26-2. EEPROM Register Map Module Base + Register Name Normal Mode Access 0x0000 EEPROM Clock Divider Register (ECLKDIV) R/W RESERVED1 1 R 0x0002 RESERVED2 1 R 0x0003 EEPROM Configuration Register (ECNFG) R/W 0x0004 EEPROM Protection Register (EPROT) R/W 0x0005 EEPROM Status Register (ESTAT) R/W 0x0006 EEPROM Command Register (ECMD) R/W 0x0001 0x0007 RESERVED3 0x0008 EEPROM High Address Register (EADDRHI)1 R 0x0009 1 R 0x000A 0x000B 1 1 R EEPROM Low Address Register (EADDRLO) 1 R 1 R EEPROM High Data Register (EDATAHI) EEPROM Low Data Register (EDATALO) Intended for factory test purposes only. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1077 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.3.2 Register Descriptions Register Name ECLKDIV Bit 7 R 6 5 4 3 2 1 Bit 0 PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 CBEIE CCIE 0 0 0 0 0 0 RNV5 RNV4 EPDIS EPS2 EPS1 EPS0 PVIOL ACCERR 0 BLANK 0 0 0 0 0 EDIVLD W RESERVED1 R W RESERVED2 R W ECNFG R W EPROT R W ESTAT R W ECMD R EPOPEN CBEIF RNV6 CCIF 0 CMDB W RESERVED3 R 0 0 0 0 0 0 0 0 0 0 W EADDRHI R EABHI W EADDRLO R EABLO W EDATAHI R EDHI W EDATALO R EDLO W = Unimplemented or Reserved Figure 26-3. EETX4K Register Summary 26.3.2.1 EEPROM Clock Divider Register (ECLKDIV) The ECLKDIV register is used to control timed events in program and erase algorithms. MC9S12XDP512 Data Sheet, Rev. 2.21 1078 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 7 R 6 5 4 3 2 1 0 PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0 0 0 0 0 0 0 0 EDIVLD W Reset 0 = Unimplemented or Reserved Figure 26-4. EEPROM Clock Divider Register (ECLKDIV) All bits in the ECLKDIV register are readable, bits 6-0 are write once and bit 7 is not writable. Table 26-3. ECLKDIV Field Descriptions Field Description 7 EDIVLD Clock Divider Loaded 0 Register has not been written. 1 Register has been written to since the last reset. 6 PRDIV8 Enable Prescalar by 8 0 The oscillator clock is directly fed into the ECLKDIV divider. 1 Enables a Prescalar by 8, to divide the oscillator clock before feeding into the clock divider. 5-0 EDIV[5:0] 26.3.2.2 Clock Divider Bits -- The combination of PRDIV8 and EDIV[5:0] effectively divides the EEPROM module input oscillator clock down to a frequency of 150 kHz - 200 kHz. The maximum divide ratio is 512. Please refer to Section 26.4.1.1, "Writing the ECLKDIV Register" for more information. RESERVED1 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 26-5. RESERVED1 All bits read 0 and are not writable. 26.3.2.3 RESERVED2 This register is reserved for factory testing and is not accessible. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1079 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 26-6. RESERVED2 All bits read 0 and are not writable. 26.3.2.4 EEPROM Configuration Register (ECNFG) The ECNFG register enables the EEPROM interrupts. 7 6 CBEIE CCIE 0 0 R 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 26-7. EEPROM Configuration Register (ECNFG) CBEIE and CCIE bits are readable and writable while all remaining bits read 0 and are not writable. Table 26-4. ECNFG Field Descriptions Field Description 7 CBEIE Command Buffer Empty Interrupt Enable -- The CBEIE bit enables an interrupt in case of an empty command buffer in the EEPROM module. 0 Command Buffer Empty interrupt disabled. 1 An interrupt will be requested whenever the CBEIF flag (see Section 26.3.2.6, "EEPROM Status Register (ESTAT)") is set. 6 CCIE Command Complete Interrupt Enable -- The CCIE bit enables an interrupt in case all commands have been completed in the EEPROM module. 0 Command Complete interrupt disabled. 1 An interrupt will be requested whenever the CCIF flag (see Section 26.3.2.6, "EEPROM Status Register (ESTAT)") is set. MC9S12XDP512 Data Sheet, Rev. 2.21 1080 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.3.2.5 EEPROM Protection Register (EPROT) The EPROT register defines which EEPROM sectors are protected against program or erase operations. 7 R 6 5 4 RNV6 RNV5 RNV4 EPOPEN 3 2 1 0 EPDIS EPS2 EPS1 EPS0 F F F F W Reset F F F F = Unimplemented or Reserved Figure 26-8. EEPROM Protection Register (EPROT) During the reset sequence, the EPROT register is loaded from the EEPROM Protection byte at address offset 0x0FFD (see Table 26-1).All bits in the EPROT register are readable and writable except for RNV[6:4] which are only readable. The EPOPEN and EPDIS bits can only be written to the protected state. The EPS bits can be written anytime until bit EPDIS is cleared. If the EPOPEN bit is cleared, the state of the EPDIS and EPS bits is irrelevant. To change the EEPROM protection that will be loaded during the reset sequence, the EEPROM memory must be unprotected, then the EEPROM Protection byte must be reprogrammed. Trying to alter data in any protected area in the EEPROM memory will result in a protection violation error and the PVIOL flag will be set in the ESTAT register. The mass erase of an EEPROM block is possible only when protection is fully disabled by setting the EPOPEN and EPDIS bits. Table 26-5. EPROT Field Descriptions Field Description 7 EPOPEN Opens the EEPROM for Program or Erase 0 The entire EEPROM memory is protected from program and erase. 1 The EEPROM sectors not protected are enabled for program or erase. 6-4 RNV[6:4] Reserved Nonvolatile Bits -- The RNV[6:4] bits should remain in the erased state "1" for future enhancements. 3 EPDIS EEPROM Protection Address Range Disable -- The EPDIS bit determines whether there is a protected area in a specific region of the EEPROM memory ending with address offset 0x0FFF. 0 Protection enabled. 1 Protection disabled. 2-0 EPS[2:0] EEPROM Protection Address Size -- The EPS[2:0] bits determine the size of the protected area as shown inTable 26-6. The EPS bits can only be written to while the EPDIS bit is set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1081 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) Table 26-6. EEPROM Protection Address Range 26.3.2.6 EPS[2:0] Address Offset Range Protected Size 000 0x0FC0 - 0x0FFF 64 bytes 001 0x0F80 - 0x0FFF 128 bytes 010 0x0F40 - 0x0FFF 192 bytes 011 0x0F00 - 0x0FFF 256 bytes 100 0x0EC0 - 0x0FFF 320 bytes 101 0x0E80 - 0x0FFF 384 bytes 110 0x0E40 - 0x0FFF 448 bytes 111 0x0E00 - 0x0FFF 512 bytes EEPROM Status Register (ESTAT) The ESTAT register defines the operational status of the module. 7 R 6 5 4 CCIF CBEIF PVIOL ACCERR 0 0 3 2 1 0 0 BLANK 0 0 0 0 0 0 W Reset 1 1 = Unimplemented or Reserved Figure 26-9. EEPROM Status Register (ESTAT -- Normal Mode) 7 R 6 5 4 CCIF CBEIF PVIOL ACCERR 0 0 3 2 0 BLANK 1 0 0 FAIL W Reset 1 1 0 0 0 0 = Unimplemented or Reserved Figure 26-10. EEPROM Status Register (ESTAT -- Special Mode) CBEIF, PVIOL, and ACCERR are readable and writable, CCIF and BLANK are readable and not writable, remaining bits read 0 and are not writable in normal mode. FAIL is readable and writable in special mode. MC9S12XDP512 Data Sheet, Rev. 2.21 1082 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) Table 26-7. ESTAT Field Descriptions Field Description 7 CBEIF Command Buffer Empty Interrupt Flag -- The CBEIF flag indicates that the address, data, and command buffers are empty so that a new command write sequence can be started. The CBEIF flag is cleared by writing a 1 to CBEIF. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned word to the EEPROM address space but before CBEIF is cleared will abort a command write sequence and cause the ACCERR flag to be set. Writing a 0 to CBEIF outside of a command write sequence will not set the ACCERR flag. The CBEIF flag is used together with the CBEIE bit in the ECNFG register to generate an interrupt request (see Figure 26-24). 0 Buffers are full. 1 Buffers are ready to accept a new command. 6 CCIF Command Complete Interrupt Flag -- The CCIF flag indicates that there are no more commands pending. The CCIF flag is cleared when CBEIF is clear and sets automatically upon completion of all active and pending commands. The CCIF flag does not set when an active commands completes and a pending command is fetched from the command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together with the CCIE bit in the ECNFG register to generate an interrupt request (see Figure 26-24). 0 Command in progress. 1 All commands are completed. 5 PVIOL Protection Violation Flag -- The PVIOL flag indicates an attempt was made to program or erase an address in a protected area of the EEPROM memory during a command write sequence. The PVIOL flag is cleared by writing a 1 to PVIOL. Writing a 0 to the PVIOL flag has no effect on PVIOL. While PVIOL is set, it is not possible to launch a command or start a command write sequence. 0 No failure. 1 A protection violation has occurred. 4 ACCERR Access Error Flag -- The ACCERR flag indicates an illegal access has occurred to the EEPROM memory caused by either a violation of the command write sequence (see Section 26.4.1.2, "Command Write Sequence"), issuing an illegal EEPROM command (see Table 26-9), launching the sector erase abort command terminating a sector erase operation early (see Section 26.4.2.5, "Sector Erase Abort Command") or the execution of a CPU STOP instruction while a command is executing (CCIF = 0). The ACCERR flag is cleared by writing a 1 to ACCERR. Writing a 0 to the ACCERR flag has no effect on ACCERR. While ACCERR is set, it is not possible to launch a command or start a command write sequence. If ACCERR is set by an erase verify operation, any buffered command will not launch. 0 No access error detected. 1 Access error has occurred. 2 BLANK Flag Indicating the Erase Verify Operation Status -- When the CCIF flag is set after completion of an erase verify command, the BLANK flag indicates the result of the erase verify operation. The BLANK flag is cleared by the EEPROM module when CBEIF is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect on BLANK. 0 EEPROM block verified as not erased. 1 EEPROM block verified as erased. 1 FAIL Flag Indicating a Failed EEPROM Operation -- The FAIL flag will set if the erase verify operation fails (EEPROM block verified as not erased). The FAIL flag is cleared by writing a 1 to FAIL. Writing a 0 to the FAIL flag has no effect on FAIL. 0 EEPROM operation completed without error. 1 EEPROM operation failed. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1083 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.3.2.7 EEPROM Command Register (ECMD) The ECMD register is the EEPROM command register. 7 R 6 5 4 3 2 1 0 0 0 0 0 CMDB W Reset 0 0 0 0 0 = Unimplemented or Reserved Figure 26-11. EEPROM Command Register (ECMD) All CMDB bits are readable and writable during a command write sequence while bit 7 reads 0 and is not writable. Table 26-8. ECMD Field Descriptions Field Description 6-0 CMDB[6:0] EEPROM Command Bits -- Valid EEPROM commands are shown in Table 26-9. Writing any command other than those listed in Table 26-9 sets the ACCERR flag in the ESTAT register. Table 26-9. Valid EEPROM Command List 26.3.2.8 CMDB[6:0] Command 0x05 Erase Verify 0x20 Word Program 0x40 Sector Erase 0x41 Mass Erase 0x47 Sector Erase Abort 0x60 Sector Modify RESERVED3 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 26-12. RESERVED3 All bits read 0 and are not writable. EEPROM Address Registers (EADDR) MC9S12XDP512 Data Sheet, Rev. 2.21 1084 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) The EADDRHI and EADDRLO registers are the EEPROM address registers. R 7 6 5 4 3 0 0 0 0 0 0 0 0 0 0 2 1 0 EABHI W Reset 0 0 0 = Unimplemented or Reserved Figure 26-13. EEPROM Address High Register (EADDRHI) 7 6 5 4 R 3 2 1 0 0 0 0 0 EABLO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 26-14. EEPROM Address Low Register (EADDRLO) All EABHI and EABLO bits read 0 and are not writable in normal modes. All EABHI and EABLO bits are readable and writable in special modes. The MCU address bit AB0 is not stored in the EADDR registers since the EEPROM block is not byte addressable. 26.3.2.9 EEPROM Data Registers (EDATA) The EDATAHI and EDATALO registers are the EEPROM data registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 EDHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 26-15. EEPROM Data High Register (EDATAHI) 7 6 5 4 R 3 2 1 0 0 0 0 0 EDLO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 26-16. EEPROM Data Low Register (EDATALO) All EDHI and EDLO bits read 0 and are not writable in normal modes. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1085 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) All EDHI and EDLO bits are readable and writable in special modes. 26.4 Functional Description 26.4.1 EEPROM Command Operations Write operations are used to execute program, erase, erase verify, sector erase abort, and sector modify algorithms described in this section. The program, erase, and sector modify algorithms are controlled by a state machine whose timebase, EECLK, is derived from the oscillator clock via a programmable divider. The command register as well as the associated address and data registers operate as a buffer and a register (2-stage FIFO) so that a second command along with the necessary data and address can be stored to the buffer while the first command is still in progress. Buffer empty as well as command completion are signalled by flags in the EEPROM status register with interrupts generated, if enabled. The next sections describe: 1. How to write the ECLKDIV register 2. Command write sequences to program, erase, erase verify, sector erase abort, and sector modify operations on the EEPROM memory 3. Valid EEPROM commands 4. Effects resulting from illegal EEPROM command write sequences or aborting EEPROM operations 26.4.1.1 Writing the ECLKDIV Register Prior to issuing any EEPROM command after a reset, the user is required to write the ECLKDIV register to divide the oscillator clock down to within the 150 kHz to 200 kHz range. Since the program and erase timings are also a function of the bus clock, the ECLKDIV determination must take this information into account. If we define: * ECLK as the clock of the EEPROM timing control block * Tbus as the period of the bus clock * INT(x) as taking the integer part of x (e.g., INT(4.323)=4) then ECLKDIV register bits PRDIV8 and EDIV[5:0] are to be set as described in Figure 26-17. For example, if the oscillator clock frequency is 950 kHz and the bus clock frequency is 10 MHz, ECLKDIV bits EDIV[5:0] should be set to 0x04 (000100) and bit PRDIV8 set to 0. The resulting EECLK frequency is then 190 kHz. As a result, the EEPROM program and erase algorithm timings are increased over the optimum target by: ( 200 - 190 ) 200 x 100 = 5% If the oscillator clock frequency is 16 MHz and the bus clock frequency is 40 MHz, ECLKDIV bits EDIV[5:0] should be set to 0x0A (001010) and bit PRDIV8 set to 1. The resulting EECLK frequency is MC9S12XDP512 Data Sheet, Rev. 2.21 1086 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) then 182 kHz. In this case, the EEPROM program and erase algorithm timings are increased over the optimum target by: ( 200 - 182 ) 200 x 100 = 9% CAUTION Program and erase command execution time will increase proportionally with the period of EECLK. Because of the impact of clock synchronization on the accuracy of the functional timings, programming or erasing the EEPROM memory cannot be performed if the bus clock runs at less than 1 MHz. Programming or erasing the EEPROM memory with EECLK < 150 kHz should be avoided. Setting ECLKDIV to a value such that EECLK < 150 kHz can destroy the EEPROM memory due to overstress. Setting ECLKDIV to a value such that (1/EECLK+Tbus) < 5 s can result in incomplete programming or erasure of the EEPROM memory cells. If the ECLKDIV register is written, the EDIVLD bit is set automatically. If the EDIVLD bit is 0, the ECLKDIV register has not been written since the last reset. If the ECLKDIV register has not been written to, the EEPROM command loaded during a command write sequence will not execute and the ACCERR flag in the ESTAT register will set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1087 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) START Tbus < 1s? no ALL COMMANDS IMPOSSIBLE yes PRDIV8 = 0 (reset) oscillator_clock >12.8 MHz? no yes PRDIV8 = 1 PRDCLK = oscillator_clock/8 PRDCLK = oscillator_clock PRDCLK[MHz]*(5+Tbus[s]) an integer? yes no EDIV[5:0]=INT(PRDCLK[MHz]*(5+Tbus[s])) EDIV[5:0]=PRDCLK[MHz]*(5+Tbus[s])-1 TRY TO DECREASE Tbus EECLK = (PRDCLK)/(1+EDIV[5:0]) 1/EECLK[MHz] + Tbus[ms] > 5 AND EECLK > 0.15 MHz ? yes END no yes EDIV[5:0] > 4? no ALL COMMANDS IMPOSSIBLE Figure 26-17. Determination Procedure for PRDIV8 and EDIV Bits MC9S12XDP512 Data Sheet, Rev. 2.21 1088 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.1.2 Command Write Sequence The EEPROM command controller is used to supervise the command write sequence to execute program, erase, erase verify, sector erase abort, and sector modify algorithms. Before starting a command write sequence, the ACCERR and PVIOL flags in the ESTAT register must be clear (see Section 26.3.2.6, "EEPROM Status Register (ESTAT)") and the CBEIF flag should be tested to determine the state of the address, data and command buffers. If the CBEIF flag is set, indicating the buffers are empty, a new command write sequence can be started. If the CBEIF flag is clear, indicating the buffers are not available, a new command write sequence will overwrite the contents of the address, data and command buffers. A command write sequence consists of three steps which must be strictly adhered to with writes to the EEPROM module not permitted between the steps. However, EEPROM register and array reads are allowed during a command write sequence. The basic command write sequence is as follows: 1. Write to one address in the EEPROM memory. 2. Write a valid command to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the command. The address written in step 1 will be stored in the EADDR registers and the data will be stored in the EDATA registers. If the CBEIF flag in the ESTAT register is clear when the first EEPROM array write occurs, the contents of the address and data buffers will be overwritten and the CBEIF flag will be set. When the CBEIF flag is cleared, the CCIF flag is cleared on the same bus cycle by the EEPROM command controller indicating that the command was successfully launched. For all command write sequences except sector erase abort, the CBEIF flag will set four bus cycles after the CCIF flag is cleared indicating that the address, data, and command buffers are ready for a new command write sequence to begin. For sector erase abort operations, the CBEIF flag will remain clear until the operation completes. Except for the sector erase abort command, a buffered command will wait for the active operation to be completed before being launched. The sector erase abort command is launched when the CBEIF flag is cleared as part of a sector erase abort command write sequence. Once a command is launched, the completion of the command operation is indicated by the setting of the CCIF flag in the ESTAT register. The CCIF flag will set upon completion of all active and buffered commands. 26.4.2 EEPROM Commands Table 26-10 summarizes the valid EEPROM commands along with the effects of the commands on the EEPROM block. Table 26-10. EEPROM Command Description ECMDB Command Function on EEPROM Memory 0x05 Erase Verify Verify all memory bytes in the EEPROM block are erased. If the EEPROM block is erased, the BLANK flag in the ESTAT register will set upon command completion. 0x20 Program 0x40 Sector Erase Program a word (two bytes) in the EEPROM block. Erase all four memory bytes in a sector of the EEPROM block. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1089 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) Table 26-10. EEPROM Command Description ECMDB Command Function on EEPROM Memory 0x41 Mass Erase Erase all memory bytes in the EEPROM block. A mass erase of the full EEPROM block is only possible when EPOPEN and EPDIS bits in the EPROT register are set prior to launching the command. 0x47 Sector Erase Abort Abort the sector erase operation. The sector erase operation will terminate according to a set procedure. The EEPROM sector should not be considered erased if the ACCERR flag is set upon command completion. 0x60 Sector Modify Erase all four memory bytes in a sector of the EEPROM block and reprogram the addressed word. CAUTION An EEPROM word (2 bytes) must be in the erased state before being programmed. Cumulative programming of bits within a word is not allowed. MC9S12XDP512 Data Sheet, Rev. 2.21 1090 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.2.1 Erase Verify Command The erase verify operation will verify that the EEPROM memory is erased. An example flow to execute the erase verify operation is shown in Figure 26-18. The erase verify command write sequence is as follows: 1. Write to an EEPROM address to start the command write sequence for the erase verify command. The address and data written will be ignored. 2. Write the erase verify command, 0x05, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the erase verify command. After launching the erase verify command, the CCIF flag in the ESTAT register will set after the operation has completed unless a new command write sequence has been buffered. The number of bus cycles required to execute the erase verify operation is equal to the number of words in the EEPROM memory plus 14 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Upon completion of the erase verify operation, the BLANK flag in the ESTAT register will be set if all addresses in the EEPROM memory are verified to be erased. If any address in the EEPROM memory is not erased, the erase verify operation will terminate and the BLANK flag in the ESTAT register will remain clear. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1091 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Address and Dummy Data 2. Write: ECMD register Erase Verify Command 0x05 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes Erase Verify Status BLANK Set? no yes EXIT EEPROM Memory Erased EXIT EEPROM Memory Not Erased Figure 26-18. Example Erase Verify Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1092 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.2.2 Program Command The program operation will program a previously erased word in the EEPROM memory using an embedded algorithm. An example flow to execute the program operation is shown in Figure 26-19. The program command write sequence is as follows: 1. Write to an EEPROM block address to start the command write sequence for the program command. The data written will be programmed to the address written. 2. Write the program command, 0x20, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the program command. If a word to be programmed is in a protected area of the EEPROM memory, the PVIOL flag in the ESTAT register will set and the program command will not launch. Once the program command has successfully launched, the CCIF flag in the ESTAT register will set after the program operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1093 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check 1. Write: EEPROM Address and program Data 2. Write: ECMD register Program Command 0x20 3. Write: ESTAT register Clear CBEIF 0x80 yes Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Buffer Empty Check no CBEIF Set? yes Sequential Programming Decision Next Word? yes no Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 26-19. Example Program Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1094 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.2.3 Sector Erase Command The sector erase operation will erase both words in a sector of EEPROM memory using an embedded algorithm. An example flow to execute the sector erase operation is shown in Figure 26-20. The sector erase command write sequence is as follows: 1. Write to an EEPROM memory address to start the command write sequence for the sector erase command. The EEPROM address written determines the sector to be erased while global address bits [1:0] and the data written are ignored. 2. Write the sector erase command, 0x40, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the sector erase command. If an EEPROM sector to be erased is in a protected area of the EEPROM memory, the PVIOL flag in the ESTAT register will set and the sector erase command will not launch. Once the sector erase command has successfully launched, the CCIF flag in the ESTAT register will set after the sector erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1095 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Sector Address and Dummy Data 2. Write: ECMD register Sector Erase Command 0x40 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 26-20. Example Sector Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1096 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.2.4 Mass Erase Command The mass erase operation will erase all addresses in an EEPROM block using an embedded algorithm. An example flow to execute the mass erase operation is shown in Figure 26-21. The mass erase command write sequence is as follows: 1. Write to an EEPROM memory address to start the command write sequence for the mass erase command. The address and data written will be ignored. 2. Write the mass erase command, 0x41, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the mass erase command. If the EEPROM memory to be erased contains any protected area, the PVIOL flag in the ESTAT register will set and the mass erase command will not launch. Once the mass erase command has successfully launched, the CCIF flag in the ESTAT register will set after the mass erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1097 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Address and Dummy Data 2. Write: ECMD register Mass Erase Command 0x41 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 26-21. Example Mass Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1098 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.2.5 Sector Erase Abort Command The sector erase abort operation will terminate the active sector erase or sector modify operation so that other sectors in an EEPROM block are available for read and program operations without waiting for the sector erase or sector modify operation to complete. An example flow to execute the sector erase abort operation is shown in Figure 26-22. The sector erase abort command write sequence is as follows: 1. Write to any EEPROM memory address to start the command write sequence for the sector erase abort command. The address and data written are ignored. 2. Write the sector erase abort command, 0x47, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the sector erase abort command. If the sector erase abort command is launched resulting in the early termination of an active sector erase or sector modify operation, the ACCERR flag will set once the operation completes as indicated by the CCIF flag being set. The ACCERR flag sets to inform the user that the EEPROM sector may not be fully erased and a new sector erase or sector modify command must be launched before programming any location in that specific sector. If the sector erase abort command is launched but the active sector erase or sector modify operation completes normally, the ACCERR flag will not set upon completion of the operation as indicated by the CCIF flag being set. If the sector erase abort command is launched after the sector modify operation has completed the sector erase step, the program step will be allowed to complete. The maximum number of cycles required to abort a sector erase or sector modify operation is equal to four EECLK periods (see Section 26.4.1.1, "Writing the ECLKDIV Register") plus five bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. NOTE Since the ACCERR bit in the ESTAT register may be set at the completion of the sector erase abort operation, a command write sequence is not allowed to be buffered behind a sector erase abort command write sequence. The CBEIF flag will not set after launching the sector erase abort command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a sector erase abort operation active, the ACCERR flag in the ESTAT register will be set. A new command write sequence may be started after clearing the ACCERR flag, if set. NOTE The sector erase abort command should be used sparingly since a sector erase operation that is aborted counts as a complete program/erase cycle. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1099 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) Execute Sector Erase/Modify Command Flow Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? Erase Abort Needed? no yes Sector Erase Completed no yes EXIT 1. Write: Dummy EEPROM Address and Dummy Data NOTE: command write sequence aborted by writing 0x00 to ESTAT register. 2. Write: ECMD register Sector Erase Abort Cmd 0x47 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. 3. Write: ESTAT register Clear CBEIF 0x80 Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes Access Error Check ACCERR Set? yes Write: ESTAT register Clear ACCERR 0x10 no Sector Erase or Modify Completed EXIT Sector Erase or Modify Aborted EXIT Figure 26-22. Example Sector Erase Abort Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1100 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.2.6 Sector Modify Command The sector modify operation will erase both words in a sector of EEPROM memory followed by a reprogram of the addressed word using an embedded algorithm. An example flow to execute the sector modify operation is shown in Figure 26-23. The sector modify command write sequence is as follows: 1. Write to an EEPROM memory address to start the command write sequence for the sector modify command. The EEPROM address written determines the sector to be erased and word to be reprogrammed while byte address bit 0 is ignored. 2. Write the sector modify command, 0x60, to the ECMD register. 3. Clear the CBEIF flag in the ESTAT register by writing a 1 to CBEIF to launch the sector erase command. If an EEPROM sector to be modified is in a protected area of the EEPROM memory, the PVIOL flag in the ESTAT register will set and the sector modify command will not launch. Once the sector modify command has successfully launched, the CCIF flag in the ESTAT register will set after the sector modify operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1101 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) START Read: ECLKDIV register Clock Register Written Check EDIVLD Set? yes NOTE: ECLKDIV needs to be set once after each reset. no Write: ECLKDIV register Read: ESTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check ACCERR/ PVIOL Set? no yes 1. Write: EEPROM Word Address and program Data 2. Write: ECMD register Sector Modify Command 0x60 3. Write: ESTAT register Clear CBEIF 0x80 Write: ESTAT register Clear ACCERR/PVIOL 0x30 NOTE: command write sequence aborted by writing 0x00 to ESTAT register. NOTE: command write sequence aborted by writing 0x00 to ESTAT register. Read: ESTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 26-23. Example Sector Modify Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1102 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.4.3 Illegal EEPROM Operations The ACCERR flag will be set during the command write sequence if any of the following illegal steps are performed, causing the command write sequence to immediately abort: 1. Writing to an EEPROM address before initializing the ECLKDIV register. 2. Writing a byte or misaligned word to a valid EEPROM address. 3. Starting a command write sequence while a sector erase abort operation is active. 4. Writing to any EEPROM register other than ECMD after writing to an EEPROM address. 5. Writing a second command to the ECMD register in the same command write sequence. 6. Writing an invalid command to the ECMD register. 7. Writing to an EEPROM address after writing to the ECMD register. 8. Writing to any EEPROM register other than ESTAT (to clear CBEIF) after writing to the ECMD register. 9. Writing a 0 to the CBEIF flag in the ESTAT register to abort a command write sequence. The ACCERR flag will not be set if any EEPROM register is read during a valid command write sequence. The ACCERR flag will also be set if any of the following events occur: 1. Launching the sector erase abort command while a sector erase or sector modify operation is active which results in the early termination of the sector erase or sector modify operation (see Section 26.4.2.5, "Sector Erase Abort Command"). 2. The MCU enters stop mode and a command operation is in progress. The operation is aborted immediately and any pending command is purged (see Section 26.5.2, "Stop Mode"). If the EEPROM memory is read during execution of an algorithm (CCIF = 0), the read operation will return invalid data and the ACCERR flag will not be set. If the ACCERR flag is set in the ESTAT register, the user must clear the ACCERR flag before starting another command write sequence (see Section 26.3.2.6, "EEPROM Status Register (ESTAT)"). The PVIOL flag will be set after the command is written to the ECMD register during a command write sequence if any of the following illegal operations are attempted, causing the command write sequence to immediately abort: 1. Writing the program command if the address written in the command write sequence was in a protected area of the EEPROM memory. 2. Writing the sector erase command if the address written in the command write sequence was in a protected area of the EEPROM memory. 3. Writing the mass erase command to the EEPROM memory while any EEPROM protection is enabled. 4. Writing the sector modify command if the address written in the command write sequence was in a protected area of the EEPROM memory. If the PVIOL flag is set in the ESTAT register, the user must clear the PVIOL flag before starting another command write sequence (see Section 26.3.2.6, "EEPROM Status Register (ESTAT)"). MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1103 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.5 26.5.1 Operating Modes Wait Mode If a command is active (CCIF = 0) when the MCU enters the wait mode, the active command and any buffered command will be completed. The EEPROM module can recover the MCU from wait mode if the CBEIF and CCIF interrupts are enabled (see Section 26.8, "Interrupts"). 26.5.2 Stop Mode If a command is active (CCIF = 0) when the MCU enters the stop mode, the operation will be aborted and, if the operation is program, sector erase, mass erase, or sector modify, the EEPROM array data being programmed or erased may be corrupted and the CCIF and ACCERR flags will be set. If active, the high voltage circuitry to the EEPROM memory will immediately be switched off when entering stop mode. Upon exit from stop mode, the CBEIF flag is set and any buffered command will not be launched. The ACCERR flag must be cleared before starting a command write sequence (see Section 26.4.1.2, "Command Write Sequence"). NOTE As active commands are immediately aborted when the MCU enters stop mode, it is strongly recommended that the user does not use the STOP instruction during program, sector erase, mass erase, or sector modify operations. 26.5.3 Background Debug Mode In background debug mode (BDM), the EPROT register is writable. If the MCU is unsecured, then all EEPROM commands listed in Table 26-10 can be executed. If the MCU is secured and is in special single chip mode, the only command available to execute is mass erase. 26.6 EEPROM Module Security The EEPROM module does not provide any security information to the MCU. After each reset, the security state of the MCU is a function of information provided by the Flash module (see the specific FTX Block Guide). MC9S12XDP512 Data Sheet, Rev. 2.21 1104 Freescale Semiconductor Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.6.1 Unsecuring the MCU in Special Single Chip Mode using BDM Before the MCU can be unsecured in special single chip mode, the EEPROM memory must be erased using the following method : * Reset the MCU into special single chip mode, delay while the erase test is performed by the BDM secure ROM, send BDM commands to disable protection in the EEPROM module, and execute a mass erase command write sequence to erase the EEPROM memory. After the CCIF flag sets to indicate that the EEPROM mass operation has completed and assuming that the Flash memory has also been erased, reset the MCU into special single chip mode. The BDM secure ROM will verify that the Flash and EEPROM memory are erased and will assert the UNSEC bit in the BDM status register. This BDM action will cause the MCU to override the Flash security state and the MCU will be unsecured. Once the MCU is unsecured, BDM commands will be enabled and the Flash security byte may be programmed to the unsecure state. 26.7 26.7.1 Resets EEPROM Reset Sequence On each reset, the EEPROM module executes a reset sequence to hold CPU activity while loading the EPROT register from the EEPROM memory according to Table 26-1. 26.7.2 Reset While EEPROM Command Active If a reset occurs while any EEPROM command is in progress, that command will be immediately aborted. The state of a word being programmed or the sector / block being erased is not guaranteed. 26.8 Interrupts The EEPROM module can generate an interrupt when all EEPROM command operations have completed, when the EEPROM address, data, and command buffers are empty. Table 26-11. EEPROM Interrupt Sources Interrupt Source Interrupt Flag Local Enable Global (CCR) Mask EEPROM address, data, and command buffers empty CBEIF (ESTAT register) CBEIE (ECNFG register) I Bit All EEPROM commands completed CCIF (ESTAT register) CCIE (ECNFG register) I Bit NOTE Vector addresses and their relative interrupt priority are determined at the MCU level. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1105 Chapter 26 4 Kbyte EEPROM Module (S12XEETX4KV2) 26.8.1 Description of EEPROM Interrupt Operation The logic used for generating interrupts is shown in Figure 26-24. The EEPROM module uses the CBEIF and CCIF flags in combination with the CBIE and CCIE enable bits to generate the EEPROM command interrupt request. CBEIF CBEIE EEPROM Command Interrupt Request CCIF CCIE Figure 26-24. EEPROM Interrupt Implementation For a detailed description of the register bits, refer to Section 26.3.2.4, "EEPROM Configuration Register (ECNFG)" and Section 26.3.2.6, "EEPROM Status Register (ESTAT)" . MC9S12XDP512 Data Sheet, Rev. 2.21 1106 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.1 Introduction This document describes the FTX512K4 module that includes a 512K Kbyte Flash (nonvolatile) memory. The Flash memory may be read as either bytes, aligned words or misaligned words. Read access time is one bus cycle for bytes and aligned words, and two bus cycles for misaligned words. The Flash memory is ideal for program and data storage for single-supply applications allowing for field reprogramming without requiring external voltage sources for program or erase. Program and erase functions are controlled by a command driven interface. The Flash module supports both block erase and sector erase. An erased bit reads 1 and a programmed bit reads 0. The high voltage required to program and erase the Flash memory is generated internally. It is not possible to read from a Flash block while it is being erased or programmed. CAUTION A Flash word must be in the erased state before being programmed. Cumulative programming of bits within a Flash word is not allowed. 27.1.1 Glossary Command Write Sequence -- A three-step MCU instruction sequence to execute built-in algorithms (including program and erase) on the Flash memory. Multiple-Input Signature Register (MISR) -- A Multiple-Input Signature Register is an output response analyzer implemented using a linear feedback shift-register (LFSR). A 16-bit MISR is used to compress data and generate a signature that is particular to the data read from a Flash block. 27.1.2 * * * * * * * * Features 512 Kbytes of Flash memory comprised of four 128 Kbyte blocks with each block divided into 128 sectors of 1024 bytes Automated program and erase algorithm Interrupts on Flash command completion, command buffer empty Fast sector erase and word program operation 2-stage command pipeline for faster multi-word program times Sector erase abort feature for critical interrupt response Flexible protection scheme to prevent accidental program or erase Single power supply for all Flash operations including program and erase MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1107 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) * * Security feature to prevent unauthorized access to the Flash memory Code integrity check using built-in data compression 27.1.3 Modes of Operation Program, erase, erase verify, and data compress operations (please refer to Section 27.4.1, "Flash Command Operations" for details). 27.1.4 Block Diagram A block diagram of the Flash module is shown in Figure 27-1. MC9S12XDP512 Data Sheet, Rev. 2.21 1108 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) FTX512K4 Flash Block 0 64K * 16 Bits sector 0 sector 1 Flash Interface Command Interrupt Request sector 127 Command Pipeline cmd2 addr2 data2_0 data2_1 data2_2 data2_3 cmd1 addr1 data1_0 data1_1 data1_2 data1_3 Flash Block 1 64K * 16 Bits sector 0 sector 1 Registers Protection sector 127 Flash Block 2 64K * 16 Bits sector 0 sector 1 Security sector 127 Oscillator Clock Clock Divider FCLK Flash Block 3 64K * 16 Bits sector 0 sector 1 sector 127 Figure 27-1. FTX512K4 Block Diagram 27.2 External Signal Description The Flash module contains no signals that connect off-chip. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1109 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.3 Memory Map and Register Definition This section describes the memory map and registers for the Flash module. 27.3.1 Module Memory Map The Flash memory map is shown in Figure 27-2. The HCS12X architecture places the Flash memory addresses between global addresses 0x78_0000 and 0x7F_FFFF. The FPROT register, described in Section 27.3.2.5, "Flash Protection Register (FPROT)", can be set to protect regions in the Flash memory from accidental program or erase. Three separate memory regions, one growing upward from global address 0x7F_8000 in the Flash memory (called the lower region), one growing downward from global address 0x7F_FFFF in the Flash memory (called the higher region), and the remaining addresses in the Flash memory, can be activated for protection. The Flash memory addresses covered by these protectable regions are shown in the Flash memory map. The higher address region is mainly targeted to hold the boot loader code since it covers the vector space. The lower address region can be used for EEPROM emulation in an MCU without an EEPROM module since it can be left unprotected while the remaining addresses are protected from program or erase. Default protection settings as well as security information that allows the MCU to restrict access to the Flash module are stored in the Flash configuration field as described in Table 27-1. Table 27-1. Flash Configuration Field Global Address Size (Bytes) 0x7F_FF00 - 0x7F_FF07 8 Backdoor Comparison Key Refer to Section 27.6.1, "Unsecuring the MCU using Backdoor Key Access" 0x7F_FF08 - 0x7F_FF0C 5 Reserved 0x7F_FF0D 1 Flash Protection byte Refer to Section 27.3.2.5, "Flash Protection Register (FPROT)" 0x7F_FF0E 1 Flash Nonvolatile byte Refer to Section 27.3.2.8, "Flash Control Register (FCTL)" 0x7F_FF0F 1 Flash Security byte Refer to Section 27.3.2.2, "Flash Security Register (FSEC)" Description MC9S12XDP512 Data Sheet, Rev. 2.21 1110 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) MODULE BASE + 0x0000 Flash Registers 16 bytes MODULE BASE + 0x000F FLASH START = 0x78_0000 Flash Protected/Unprotected Region 480 Kbytes 0x7F_8000 0x7F_8400 0x7F_8800 0x7F_9000 Flash Protected/Unprotected Lower Region 1, 2, 4, 8 Kbytes 0x7F_A000 Flash Protected/Unprotected Region 8 Kbytes (up to 29 Kbytes) 0x7F_C000 0x7F_E000 Flash Protected/Unprotected Higher Region 2, 4, 8, 16 Kbytes 0x7F_F000 0x7F_F800 FLASH END = 0x7F_FFFF Flash Configuration Field 16 bytes (0x7F_FF00 - 0x7F_FF0F) Figure 27-2. Flash Memory Map MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1111 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) The Flash module also contains a set of 16 control and status registers located between module base + 0x0000 and 0x000F. A summary of the Flash module registers is given in Table 27-2 while their accessibility is detailed in Section 27.3.2, "Register Descriptions". Table 27-2. Flash Register Map Module Base + Register Name Normal Mode Access 0x0000 Flash Clock Divider Register (FCLKDIV) R/W 0x0001 Flash Security Register (FSEC) R 0x0002 Flash Test Mode Register (FTSTMOD) R/W 0x0003 Flash Configuration Register (FCNFG) R/W 0x0004 Flash Protection Register (FPROT) R/W 0x0005 Flash Status Register (FSTAT) R/W 0x0006 Flash Command Register (FCMD) R/W 0x0007 Flash Control Register (FCTL) 0x0008 R 1 R 1 Flash High Address Register (FADDRHI) 0x0009 Flash Low Address Register (FADDRLO) R 0x000A Flash High Data Register (FDATAHI) R 0x000B Flash Low Data Register (FDATALO) R 0x000C RESERVED11 R 0x000D RESERVED21 R 0x000E RESERVED31 R 0x000F RESERVED41 R 1 Intended for factory test purposes only. MC9S12XDP512 Data Sheet, Rev. 2.21 1112 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.3.2 Register Descriptions Register Name FCLKDIV Bit 7 R 6 5 4 3 2 1 Bit 0 PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0 RNV5 RNV4 RNV3 RNV2 0 0 0 0 0 0 0 0 0 0 FDIVLD W FSEC R KEYEN SEC W FTSTMOD R 0 MRDS W FCNFG R CBEIE CCIE KEYACC W FPROT R RNV6 FPOPEN FPHDIS FPHS FPLDIS FPLS W FSTAT R CCIF CBEIF 0 PVIOL BLANK 0 0 NV2 NV1 NV0 0 0 0 ACCERR W FCMD R 0 CMDB W FCTL R NV7 NV6 NV5 NV4 NV3 W FADDRHI R FADDRHI W FADDRLO R FADDRLO W FDATAHI R FDATAHI W FDATALO R FDATALO W RESERVED1 R 0 0 0 0 0 W Figure 27-3. FTX512K4 Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1113 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) Register Name RESERVED2 R Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W RESERVED3 R W RESERVED4 R W Figure 27-3. FTX512K4 Register Summary (continued) 27.3.2.1 Flash Clock Divider Register (FCLKDIV) The FCLKDIV register is used to control timed events in program and erase algorithms. 7 R 6 5 4 3 2 1 0 PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0 0 0 0 0 0 0 0 FDIVLD W Reset 0 = Unimplemented or Reserved Figure 27-4. Flash Clock Divider Register (FCLKDIV) All bits in the FCLKDIV register are readable, bits 6-0 are write once and bit 7 is not writable. Table 27-3. FCLKDIV Field Descriptions Field Description 7 FDIVLD Clock Divider Loaded. 0 Register has not been written. 1 Register has been written to since the last reset. 6 PRDIV8 Enable Prescalar by 8. 0 The oscillator clock is directly fed into the clock divider. 1 The oscillator clock is divided by 8 before feeding into the clock divider. 5-0 FDIV[5:0] 27.3.2.2 Clock Divider Bits -- The combination of PRDIV8 and FDIV[5:0] must divide the oscillator clock down to a frequency of 150 kHz-200 kHz. The maximum divide ratio is 512. Please refer to Section 27.4.1.1, "Writing the FCLKDIV Register" for more information. Flash Security Register (FSEC) The FSEC register holds all bits associated with the security of the MCU and Flash module. MC9S12XDP512 Data Sheet, Rev. 2.21 1114 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 7 R 6 KEYEN 5 4 3 2 RNV5 RNV4 RNV3 RNV2 F F F F 1 0 SEC W Reset F F F F = Unimplemented or Reserved Figure 27-5. Flash Security Register (FSEC) All bits in the FSEC register are readable but are not writable. The FSEC register is loaded from the Flash Configuration Field at address 0x7F_FF0F during the reset sequence, indicated by F in Figure 27-5. Table 27-4. FSEC Field Descriptions Field Description 7-6 Backdoor Key Security Enable Bits -- The KEYEN[1:0] bits define the enabling of backdoor key access to the KEYEN[1:0] Flash module as shown in Table 27-5. 5-2 RNV[5:2] Reserved Nonvolatile Bits -- The RNV[5:2] bits should remain in the erased state for future enhancements. 1-0 SEC[1:0] Flash Security Bits -- The SEC[1:0] bits define the security state of the MCU as shown in Table 27-6. If the Flash module is unsecured using backdoor key access, the SEC[1:0] bits are forced to 1:0. Table 27-5. Flash KEYEN States KEYEN[1:0] Status of Backdoor Key Access 00 DISABLED 1 DISABLED 01 10 ENABLED 11 DISABLED 1 Preferred KEYEN state to disable Backdoor Key Access. Table 27-6. Flash Security States SEC[1:0] Status of Security 00 SECURED 011 SECURED 10 UNSECURED 11 SECURED 1 Preferred SEC state to set MCU to secured state. The security function in the Flash module is described in Section 27.6, "Flash Module Security". 27.3.2.3 Flash Test Mode Register (FTSTMOD) The FTSTMOD register is used to control Flash test features. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1115 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 7 R 6 5 0 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 MRDS W Reset 0 0 0 = Unimplemented or Reserved Figure 27-6. Flash Test Mode Register (FTSTMOD --Normal Mode) 7 R 6 5 4 0 MRDS 3 2 1 0 0 0 0 0 0 0 0 0 WRALL W Reset 0 0 0 0 = Unimplemented or Reserved Figure 27-7. Flash Test Mode Register (FTSTMOD -- Special Mode) MRDS bits are readable and writable while all remaining bits read 0 and are not writable in normal mode. The WRALL bit is writable only in special mode to simplify mass erase and erase verify operations. When writing to the FTSTMOD register in special mode, all unimplemented/reserved bits must be written to 0. Table 27-7. FTSTMOD Field Descriptions Field Description 6-5 MRDS[1:0] Margin Read Setting -- The MRDS[1:0] bits are used to set the sense-amp margin level for reads of the Flash array as shown in Table 27-8. 4 WRALL Write to all Register Banks -- If the WRALL bit is set, all banked FDATA registers sharing the same register address will be written simultaneously during a register write. 0 Write only to the FDATA register bank selected using BKSEL. 1 Write to all FDATA register banks. Table 27-8. FTSTMOD Margin Read Settings MRDS[1:0] Margin Read Setting 00 Normal 01 Program Margin1 10 Erase Margin2 11 Normal 1 Flash array reads will be sensitive to program margin. 2 Flash array reads will be sensitive to erase margin. 27.3.2.4 Flash Configuration Register (FCNFG) The FCNFG register enables the Flash interrupts and gates the security backdoor writes. MC9S12XDP512 Data Sheet, Rev. 2.21 1116 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 7 6 5 CBEIE CCIE KEYACC 0 0 0 R 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 1 0 W Reset = Unimplemented or Reserved Figure 27-8. Flash Configuration Register (FCNFG -- Normal Mode) 7 6 5 R CBEIE CCIE KEYACC 0 0 0 4 3 2 Undefined 0 0 BKSEL W Reset Undefined 0 0 0 0 = Unimplemented or Reserved Figure 27-9. Flash Configuration Register (FCNFG -- Special Mode) CBEIE, CCIE and KEYACC bits are readable and writable while all remaining bits read 0 and are not writable in normal mode. KEYACC is only writable if KEYEN (see Section 27.3.2.2, "Flash Security Register (FSEC)" is set to the enabled state. BKSEL is readable and writable in special mode to simplify mass erase and erase verify operations. When writing to the FCNFG register in special mode, all unimplemented/ reserved bits must be written to 0. Table 27-9. FCNFG Field Descriptions Field Description 7 CBEIE Command Buffer Empty Interrupt Enable -- The CBEIE bit enables an interrupt in case of an empty command buffer in the Flash module. 0 Command buffer empty interrupt disabled. 1 An interrupt will be requested whenever the CBEIF flag (see Section 27.3.2.6, "Flash Status Register (FSTAT)") is set. 6 CCIE Command Complete Interrupt Enable -- The CCIE bit enables an interrupt in case all commands have been completed in the Flash module. 0 Command complete interrupt disabled. 1 An interrupt will be requested whenever the CCIF flag (see Section 27.3.2.6, "Flash Status Register (FSTAT)") is set. 5 KEYACC Enable Security Key Writing 0 Flash writes are interpreted as the start of a command write sequence. 1 Writes to Flash array are interpreted as keys to open the backdoor. Reads of the Flash array return invalid data. 1-0 Block Select -- The BKSEL[1:0] bits indicates which register bank is active according to Table 27-10. BKSEL[1:0] Table 27-10. Flash Register Bank Selects BKSEL[1:0] Selected Block 00 Flash Block 0 01 Flash Block 1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1117 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) Table 27-10. Flash Register Bank Selects 27.3.2.5 BKSEL[1:0] Selected Block 10 Flash Block 2 11 Flash Block 3 Flash Protection Register (FPROT) The FPROT register defines which Flash sectors are protected against program or erase operations. 7 R 6 5 4 3 2 1 0 RNV6 FPOPEN FPHDIS FPHS FPLDIS FPLS W Reset F F F F F F F F = Unimplemented or Reserved Figure 27-10. Flash Protection Register (FPROT) All bits in the FPROT register are readable and writable with restrictions (see Section 27.3.2.5.1, "Flash Protection Restrictions") except for RNV[6] which is only readable. During the reset sequence, the FPROT register is loaded from the Flash Configuration Field at global address 0x7F_FF0D. To change the Flash protection that will be loaded during the reset sequence, the upper sector of the Flash memory must be unprotected, then the Flash Protect/Security byte located as described in Table 27-1 must be reprogrammed. Trying to alter data in any protected area in the Flash memory will result in a protection violation error and the PVIOL flag will be set in the FSTAT register. The mass erase of a Flash block is not possible if any of the Flash sectors contained in the Flash block are protected. Table 27-11. FPROT Field Descriptions Field Description 7 FPOPEN Flash Protection Open -- The FPOPEN bit determines the protection function for program or erase as shown in Table 27-12. 0 The FPHDIS and FPLDIS bits define unprotected address ranges as specified by the corresponding FPHS[1:0] and FPLS[1:0] bits. For an MCU without an EEPROM module, the FPOPEN clear state allows the main part of the Flash block to be protected while a small address range can remain unprotected for EEPROM emulation. 1 The FPHDIS and FPLDIS bits enable protection for the address range specified by the corresponding FPHS[1:0] and FPLS[1:0] bits. 6 RNV6 5 FPHDIS 4-3 FPHS[1:0] Reserved Nonvolatile Bit -- The RNV[6] bit should remain in the erased state for future enhancements. Flash Protection Higher Address Range Disable -- The FPHDIS bit determines whether there is a protected/unprotected area in a specific region of the Flash memory ending with global address 0x7F_FFFF. 0 Protection/Unprotection enabled. 1 Protection/Unprotection disabled. Flash Protection Higher Address Size -- The FPHS[1:0] bits determine the size of the protected/unprotected area as shown inTable 27-13. The FPHS[1:0] bits can only be written to while the FPHDIS bit is set. MC9S12XDP512 Data Sheet, Rev. 2.21 1118 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) Table 27-11. FPROT Field Descriptions (continued) Field Description 2 FPLDIS Flash Protection Lower Address Range Disable -- The FPLDIS bit determines whether there is a protected/unprotected area in a specific region of the Flash memory beginning with global address 0x7F_8000. 0 Protection/Unprotection enabled. 1 Protection/Unprotection disabled. 1-0 FPLS[1:0] Flash Protection Lower Address Size -- The FPLS[1:0] bits determine the size of the protected/unprotected area as shown in Table 27-14. The FPLS[1:0] bits can only be written to while the FPLDIS bit is set. Table 27-12. Flash Protection Function Function1 FPOPEN FPHDIS FPLDIS 1 1 1 No Protection 1 1 0 Protected Low Range 1 0 1 Protected High Range 1 0 0 Protected High and Low Ranges 0 1 1 Full Flash memory Protected 0 1 0 Unprotected Low Range 0 0 1 Unprotected High Range 0 0 0 Unprotected High and Low Ranges 1 For range sizes, refer to Table 27-13 and Table 27-14. Table 27-13. Flash Protection Higher Address Range FPHS[1:0] Global Address Range Protected Size 00 0x7F_F800-0x7F_FFFF 2 Kbytes 01 0x7F_F000-0x7F_FFFF 4 Kbytes 10 0x7F_E000-0x7F_FFFF 8 Kbytes 11 0x7F_C000-0x7F_FFFF 16 Kbytes Table 27-14. Flash Protection Lower Address Range FPLS[1:0] Global Address Range Protected Size 00 0x7F_8000-0x7F_83FF 1 Kbytes 01 0x7F_8000-0x7F_87FF 2 Kbytes 10 0x7F_8000-0x7F_8FFF 4 Kbytes 11 0x7F_8000-0x7F_9FFF 8 Kbytes All possible Flash protection scenarios are shown in Figure 27-11. Although the protection scheme is loaded from the Flash array at global address 0x7F_FF0D during the reset sequence, it can be changed by the user. This protection scheme can be used by applications requiring re-programming in single chip mode while providing as much protection as possible if re-programming is not required. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1119 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) FPHDIS=1 FPLDIS=1 FPHDIS=1 FPLDIS=0 FPHDIS=0 FPLDIS=1 FPHDIS=0 FPLDIS=0 7 6 5 4 0x78_0000 Scenario 0x7F_8000 FPLS[1:0] FPOPEN=1 FPHS[1:0] 0x7F_FFFF 3 2 Scenario 1 0 0x78_0000 0x7F_8000 FPLS[1:0] FPOPEN=0 FPHS[1:0] 0x7F_FFFF Unprotected region Protected region with size defined by FPLS Protected region not defined by FPLS, FPHS Protected region with size defined by FPHS Figure 27-11. Flash Protection Scenarios MC9S12XDP512 Data Sheet, Rev. 2.21 1120 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.3.2.5.1 Flash Protection Restrictions The general guideline is that Flash protection can only be added and not removed. Table 27-15 specifies all valid transitions between Flash protection scenarios. Any attempt to write an invalid scenario to the FPROT register will be ignored and the FPROT register will remain unchanged. The contents of the FPROT register reflect the active protection scenario. See the FPHS and FPLS descriptions for additional restrictions. Table 27-15. Flash Protection Scenario Transitions To Protection Scenario1 From Protection Scenario 0 1 2 3 0 X X X X 1 X 2 4 X 4 X X X X X X X X X X 7 X X 7 X 3 6 6 X X 5 5 X X X X X X 1 Allowed transitions marked with X. 27.3.2.6 Flash Status Register (FSTAT) The FSTAT register defines the operational status of the module. 7 6 R 5 4 PVIOL ACCERR 0 0 CCIF CBEIF 3 2 1 0 0 BLANK 0 0 0 0 0 0 W Reset 1 1 = Unimplemented or Reserved Figure 27-12. Flash Status Register (FSTAT -- Normal Mode) 7 6 R 5 4 CCIF CBEIF PVIOL ACCERR 0 0 3 2 0 BLANK 1 0 0 FAIL W Reset 1 1 0 0 0 0 = Unimplemented or Reserved Figure 27-13. Flash Status Register (FSTAT -- Special Mode) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1121 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) CBEIF, PVIOL, and ACCERR are readable and writable, CCIF and BLANK are readable and not writable, remaining bits read 0 and are not writable in normal mode. FAIL is readable and writable in special mode. FAIL must be clear in special mode when starting a command write sequence. Table 27-16. FSTAT Field Descriptions Field Description 7 CBEIF Command Buffer Empty Interrupt Flag -- The CBEIF flag indicates that the address, data and command buffers are empty so that a new command write sequence can be started. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned word to the Flash address space, but before CBEIF is cleared, will abort a command write sequence and cause the ACCERR flag to be set. Writing a 0 to CBEIF outside of a command write sequence will not set the ACCERR flag. The CBEIF flag is cleared by writing a 1 to CBEIF. The CBEIF flag is used together with the CBEIE bit in the FCNFG register to generate an interrupt request (see Figure 27-32). 0 Command buffers are full. 1 Command buffers are ready to accept a new command. 6 CCIF Command Complete Interrupt Flag -- The CCIF flag indicates that there are no more commands pending. The CCIF flag is cleared when CBEIF is cleared and sets automatically upon completion of all active and pending commands. The CCIF flag does not set when an active commands completes and a pending command is fetched from the command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together with the CCIE bit in the FCNFG register to generate an interrupt request (see Figure 27-32). 0 Command in progress. 1 All commands are completed. 5 PVIOL Protection Violation Flag --The PVIOL flag indicates an attempt was made to program or erase an address in a protected area of the Flash memory during a command write sequence. Writing a 0 to the PVIOL flag has no effect on PVIOL. The PVIOL flag is cleared by writing a 1 to PVIOL. While PVIOL is set, it is not possible to launch a command or start a command write sequence. 0 No protection violation detected. 1 Protection violation has occurred. 4 ACCERR Access Error Flag -- The ACCERR flag indicates an illegal access has occurred to the Flash memory caused by either a violation of the command write sequence (see Section 27.4.1.2, "Command Write Sequence"), issuing an illegal Flash command (see Table 27-18), launching the sector erase abort command terminating a sector erase operation early (see Section 27.4.2.6, "Sector Erase Abort Command") or the execution of a CPU STOP instruction while a command is executing (CCIF = 0). Writing a 0 to the ACCERR flag has no effect on ACCERR. The ACCERR flag is cleared by writing a 1 to ACCERR.While ACCERR is set, it is not possible to launch a command or start a command write sequence. If ACCERR is set by an erase verify operation or a data compress operation, any buffered command will not launch. 0 No access error detected. 1 Access error has occurred. 2 BLANK Flag Indicating the Erase Verify Operation Status -- When the CCIF flag is set after completion of an erase verify command, the BLANK flag indicates the result of the erase verify operation. The BLANK flag is cleared by the Flash module when CBEIF is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect on BLANK. 0 Flash block verified as not erased. 1 Flash block verified as erased. 1 FAIL Flag Indicating a Failed Flash Operation -- The FAIL flag will set if the erase verify operation fails (selected Flash block verified as not erased). Writing a 0 to the FAIL flag has no effect on FAIL. The FAIL flag is cleared by writing a 1 to FAIL. 0 Flash operation completed without error. 1 Flash operation failed. MC9S12XDP512 Data Sheet, Rev. 2.21 1122 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.3.2.7 Flash Command Register (FCMD) The FCMD register is the Flash command register. 7 R 6 5 4 3 2 1 0 0 0 0 0 CMDB W Reset 1 1 0 0 0 = Unimplemented or Reserved Figure 27-14. Flash Command Register (FCMD) All CMDB bits are readable and writable during a command write sequence while bit 7 reads 0 and is not writable. Table 27-17. FCMD Field Descriptions Field Description 6-0 CMDB[6:0] Flash Command -- Valid Flash commands are shown in Table 27-18. Writing any command other than those listed in Table 27-18 sets the ACCERR flag in the FSTAT register. Table 27-18. Valid Flash Command List 27.3.2.8 CMDB[6:0] NVM Command 0x05 Erase Verify 0x06 Data Compress 0x20 Word Program 0x40 Sector Erase 0x41 Mass Erase 0x47 Sector Erase Abort Flash Control Register (FCTL) The FCTL register is the Flash control register. R 7 6 5 4 3 2 1 0 NV7 NV6 NV5 NV4 NV3 NV2 NV1 NV0 F F F F F F F F W Reset = Unimplemented or Reserved Figure 27-15. Flash Control Register (FCTL) All bits in the FCTL register are readable but are not writable. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1123 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) The FCTL register is loaded from the Flash Configuration Field byte at global address 0x7F_FF0E during the reset sequence, indicated by F in Figure 27-15. Table 27-19. FCTL Field Descriptions Field Description 7-0 NV[7:0] Non volatile Bits -- The NV[7:0] bits are available as nonvolatile bits. Refer to the Device User Guide for proper use of the NV bits. 27.3.2.9 Flash Address Registers (FADDR) The FADDRHI and FADDRLO registers are the Flash address registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 FADDRHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 27-16. Flash Address High Register (FADDRHI) 7 6 5 4 R 3 2 1 0 0 0 0 0 FADDRLO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 27-17. Flash Address Low Register (FADDRLO) All FADDRHI and FADDRLO bits are readable but are not writable. After an array write as part of a command write sequence, the FADDR registers will contain the mapped MCU address written. 27.3.2.10 Flash Data Registers (FDATA) The FDATAHI and FDATALO registers are the Flash data registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 FDATAHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 27-18. Flash Data High Register (FDATAHI) MC9S12XDP512 Data Sheet, Rev. 2.21 1124 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 7 6 5 4 R 3 2 1 0 0 0 0 0 FDATALO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 27-19. Flash Data Low Register (FDATALO) All FDATAHI and FDATALO bits are readable but are not writable. At the completion of a data compress operation, the resulting 16-bit signature is stored in the FDATA registers. The data compression signature is readable in the FDATA registers until a new command write sequence is started. 27.3.2.11 RESERVED1 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 27-20. RESERVED1 All bits read 0 and are not writable. 27.3.2.12 RESERVED2 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 27-21. RESERVED2 All bits read 0 and are not writable. 27.3.2.13 RESERVED3 This register is reserved for factory testing and is not accessible. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1125 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 27-22. RESERVED3 All bits read 0 and are not writable. 27.3.2.14 RESERVED4 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 27-23. RESERVED4 All bits read 0 and are not writable. 27.4 27.4.1 Functional Description Flash Command Operations Write operations are used to execute program, erase, erase verify, erase abort, and data compress algorithms described in this section. The program and erase algorithms are controlled by a state machine whose timebase, FCLK, is derived from the oscillator clock via a programmable divider. The command register, as well as the associated address and data registers, operate as a buffer and a register (2-stage FIFO) so that a second command along with the necessary data and address can be stored to the buffer while the first command is still in progress. This pipelined operation allows a time optimization when programming more than one word on a specific row in the Flash block as the high voltage generation can be kept active in between two programming commands. The pipelined operation also allows a simplification of command launching. Buffer empty as well as command completion are signalled by flags in the Flash status register with corresponding interrupts generated, if enabled. The next sections describe: 1. How to write the FCLKDIV register 2. Command write sequences to program, erase, erase verify, erase abort, and data compress operations on the Flash memory 3. Valid Flash commands 4. Effects resulting from illegal Flash command write sequences or aborting Flash operations MC9S12XDP512 Data Sheet, Rev. 2.21 1126 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.1.1 Writing the FCLKDIV Register Prior to issuing any Flash command after a reset, the user is required to write the FCLKDIV register to divide the oscillator clock down to within the 150 kHz to 200 kHz range. Since the program and erase timings are also a function of the bus clock, the FCLKDIV determination must take this information into account. If we define: * FCLK as the clock of the Flash timing control block * Tbus as the period of the bus clock * INT(x) as taking the integer part of x (e.g. INT(4.323) = 4) then FCLKDIV register bits PRDIV8 and FDIV[5:0] are to be set as described in Figure 27-24. For example, if the oscillator clock frequency is 950kHz and the bus clock frequency is 10MHz, FCLKDIV bits FDIV[5:0] should be set to 0x04 (000100) and bit PRDIV8 set to 0. The resulting FCLK frequency is then 190kHz. As a result, the Flash program and erase algorithm timings are increased over the optimum target by: ( 200 - 190 ) 200 x 100 = 5% If the oscillator clock frequency is 16MHz and the bus clock frequency is 40MHz, FCLKDIV bits FDIV[5:0] should be set to 0x0A (001010) and bit PRDIV8 set to 1. The resulting FCLK frequency is then 182kHz. In this case, the Flash program and erase algorithm timings are increased over the optimum target by: ( 200 - 182 ) 200 x 100 = 9% CAUTION Program and erase command execution time will increase proportionally with the period of FCLK. Because of the impact of clock synchronization on the accuracy of the functional timings, programming or erasing the Flash memory cannot be performed if the bus clock runs at less than 1 MHz. Programming or erasing the Flash memory with FCLK < 150 kHz should be avoided. Setting FCLKDIV to a value such that FCLK < 150 kHz can destroy the Flash memory due to overstress. Setting FCLKDIV to a value such that (1/FCLK+Tbus) < 5s can result in incomplete programming or erasure of the Flash memory cells. If the FCLKDIV register is written, the FDIVLD bit is set automatically. If the FDIVLD bit is 0, the FCLKDIV register has not been written since the last reset. If the FCLKDIV register has not been written to, the Flash command loaded during a command write sequence will not execute and the ACCERR flag in the FSTAT register will set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1127 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) START Tbus < 1s? no ALL COMMANDS IMPOSSIBLE yes PRDIV8=0 (reset) oscillator_clock 12.8MHz? no yes PRDIV8=1 PRDCLK=oscillator_clock/8 PRDCLK[MHz]*(5+Tbus[s]) an integer? yes PRDCLK=oscillator_clock no FDIV[5:0]=INT(PRDCLK[MHz]*(5+Tbus[s])) FDIV[5:0]=PRDCLK[MHz]*(5+Tbus[s])-1 TRY TO DECREASE Tbus FCLK=(PRDCLK)/(1+FDIV[5:0]) 1/FCLK[MHz] + Tbus[s] > 5 AND FCLK > 0.15MHz ? yes END no yes FDIV[5:0] > 4? no ALL COMMANDS IMPOSSIBLE Figure 27-24. Determination Procedure for PRDIV8 and FDIV Bits MC9S12XDP512 Data Sheet, Rev. 2.21 1128 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.1.2 Command Write Sequence The Flash command controller is used to supervise the command write sequence to execute program, erase, erase verify, erase abort, and data compress algorithms. Before starting a command write sequence, the ACCERR and PVIOL flags in the FSTAT register must be clear (see Section 27.3.2.6, "Flash Status Register (FSTAT)") and the CBEIF flag should be tested to determine the state of the address, data and command buffers. If the CBEIF flag is set, indicating the buffers are empty, a new command write sequence can be started. If the CBEIF flag is clear, indicating the buffers are not available, a new command write sequence will overwrite the contents of the address, data and command buffers. A command write sequence consists of three steps which must be strictly adhered to with writes to the Flash module not permitted between the steps. However, Flash register and array reads are allowed during a command write sequence. The basic command write sequence is as follows: 1. Write to a valid address in the Flash memory. Addresses in multiple Flash blocks can be written to as long as the location is at the same relative address in each available Flash block. Multiple addresses must be written in Flash block order starting with the lower Flash block. 2. Write a valid command to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the command. The address written in step 1 will be stored in the FADDR registers and the data will be stored in the FDATA registers. If the CBEIF flag in the FSTAT register is clear when the first Flash array write occurs, the contents of the address and data buffers will be overwritten and the CBEIF flag will be set. When the CBEIF flag is cleared, the CCIF flag is cleared on the same bus cycle by the Flash command controller indicating that the command was successfully launched. For all command write sequences except data compress and sector erase abort, the CBEIF flag will set four bus cycles after the CCIF flag is cleared indicating that the address, data, and command buffers are ready for a new command write sequence to begin. For data compress and sector erase abort operations, the CBEIF flag will remain clear until the operation completes. Except for the sector erase abort command, a buffered command will wait for the active operation to be completed before being launched. The sector erase abort command is launched when the CBEIF flag is cleared as part of a sector erase abort command write sequence. Once a command is launched, the completion of the command operation is indicated by the setting of the CCIF flag in the FSTAT register. The CCIF flag will set upon completion of all active and buffered commands. 27.4.2 Flash Commands Table 27-20 summarizes the valid Flash commands along with the effects of the commands on the Flash block. Table 27-20. Flash Command Description FCMDB 0x05 NVM Command Erase Verify Function on Flash Memory Verify all memory bytes in the Flash block are erased. If the Flash block is erased, the BLANK flag in the FSTAT register will set upon command completion. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1129 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) Table 27-20. Flash Command Description NVM Command Function on Flash Memory 0x06 Data Compress Compress data from a selected portion of the Flash block. The resulting signature is stored in the FDATA register. 0x20 Program 0x40 Sector Erase Erase all memory bytes in a sector of the Flash block. 0x41 Mass Erase Erase all memory bytes in the Flash block. A mass erase of the full Flash block is only possible when FPLDIS, FPHDIS and FPOPEN bits in the FPROT register are set prior to launching the command. 0x47 Sector Erase Abort Abort the sector erase operation. The sector erase operation will terminate according to a set procedure. The Flash sector should not be considered erased if the ACCERR flag is set upon command completion. FCMDB Program a word (two bytes) in the Flash block. CAUTION A Flash word must be in the erased state before being programmed. Cumulative programming of bits within a Flash word is not allowed. MC9S12XDP512 Data Sheet, Rev. 2.21 1130 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.2.1 Erase Verify Command The erase verify operation will verify that a Flash block is erased. An example flow to execute the erase verify operation is shown in Figure 27-25. The erase verify command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the erase verify command. The address and data written will be ignored. Multiple Flash blocks can be simultaneously erase verified by writing to the same relative address in each Flash block. 2. Write the erase verify command, 0x05, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the erase verify command. After launching the erase verify command, the CCIF flag in the FSTAT register will set after the operation has completed unless a new command write sequence has been buffered. The number of bus cycles required to execute the erase verify operation is equal to the number of addresses in a Flash block plus 14 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Upon completion of the erase verify operation, the BLANK flag in the FSTAT register will be set if all addresses in the selected Flash blocks are verified to be erased. If any address in a selected Flash block is not erased, the erase verify operation will terminate and the BLANK flag in the FSTAT register will remain clear. The MRDS bits in the FTSTMOD register will determine the sense-amp margin setting during the erase verify operation. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1131 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check 1. Simultaneous Multiple Flash Block Decision ACCERR/ PVIOL Set? no yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Block Address and Dummy Data Next Flash Block? yes 2. no Write: FCMD register Erase Verify Command 0x05 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Erase Verify Status BLANK Set? no yes EXIT Flash Block Erased EXIT Flash Block Not Erased Figure 27-25. Example Erase Verify Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1132 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.2.2 Data Compress Command The data compress operation will check Flash code integrity by compressing data from a selected portion of the Flash memory into a signature analyzer. An example flow to execute the data compress operation is shown in Figure 27-26. The data compress command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the data compress command. The address written determines the starting address for the data compress operation and the data written determines the number of consecutive words to compress. If the data value written is 0x0000, 64K addresses or 128 Kbytes will be compressed. Multiple Flash blocks can be simultaneously compressed by writing to the same relative address in each Flash block. If more than one Flash block is written to in this step, the first data written will determine the number of consecutive words to compress in each selected Flash block. 2. Write the data compress command, 0x06, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the data compress command. After launching the data compress command, the CCIF flag in the FSTAT register will set after the data compress operation has completed. The number of bus cycles required to execute the data compress operation is equal to two times the number of consecutive words to compress plus the number of Flash blocks simultaneously compressed plus 18 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Once the CCIF flag is set, the signature generated by the data compress operation is available in the FDATA registers. The signature in the FDATA registers can be compared to the expected signature to determine the integrity of the selected data stored in the selected Flash memory. If the last address of a Flash block is reached during the data compress operation, data compression will continue with the starting address of the same Flash block. The MRDS bits in the FTSTMOD register will determine the sense-amp margin setting during the data compress operation. NOTE Since the FDATA registers (or data buffer) are written to as part of the data compress operation, a command write sequence is not allowed to be buffered behind a data compress command write sequence. The CBEIF flag will not set after launching the data compress command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a data compress operation active, the ACCERR flag in the FSTAT register will be set. A new command write sequence should only be started after reading the signature stored in the FDATA registers. In order to take corrective action, it is recommended that the data compress command be executed on a Flash sector or subset of a Flash sector. If the data compress operation on a Flash sector returns an invalid signature, the Flash sector should be erased using the sector erase command and then reprogrammed using the program command. The data compress command can be used to verify that a sector or sequential set of sectors are erased. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1133 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Address to start compression and number of word addresses to compress 1. NOTE: address used to select Flash block; data ignored. Simultaneous Multiple Flash Block Decision Next Flash Block? yes 2. no Write: FCMD register Data Compress Command 0x06 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Read: FDATA registers Data Compress Signature Signature Valid? no Erase and Reprogram Flash Sector(s) Compressed yes EXIT Figure 27-26. Example Data Compress Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1134 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.2.2.1 Data Compress Operation The Flash module contains a 16-bit multiple-input signature register (MISR) for each Flash block to generate a 16-bit signature based on selected Flash array data. If multiple Flash blocks are selected for simultaneous compression, then the signature from each Flash block is further compressed to generate a single 16-bit signature. The final 16-bit signature, found in the FDATA registers after the data compress operation has completed, is based on the following logic equation which is executed on every data compression cycle during the operation: MISR[15:0] = {MISR[14:0], ^MISR[15,4,2,1]} ^ DATA[15:0] Eqn. 27-1 where MISR is the content of the internal signature register associated with each Flash block and DATA is the data to be compressed as shown in Figure 27-27. DATA[0] + DATA[1] DQ DATA[2] + M0 > + DQ M1 > DATA[3] + DQ M2 > + DATA[4] DQ M3 > + + DATA[5] + DQ M4 > DATA[15] DQ M5 > ... + DQ M15 > + + = Exclusive-OR MISR[15:0] = Q[15:0] Figure 27-27. 16-Bit MISR Diagram During the data compress operation, the following steps are executed: 1. MISR for each Flash block is reset to 0xFFFF. 2. Initialized DATA equal to 0xFFFF is compressed into the MISR for each selected Flash block which results in the MISR containing 0x0001. 3. DATA equal to the selected Flash array data range is read and compressed into the MISR for each selected Flash block with addresses incrementing. 4. DATA equal to the selected Flash array data range is read and compressed into the MISR for each selected Flash block with addresses decrementing. 5. If Flash block 0 is selected for compression, DATA equal to the contents of the MISR for Flash block 0 is compressed into the MISR for Flash block 0. If data in Flash block 0 was not selected for compression, the MISR for Flash block 0 contains 0xFFFF. 6. If Flash block 1 is selected for compression, DATA equal to the contents of the MISR for Flash block 1 is compressed into the MISR for Flash block 0. 7. If Flash block 2 is selected for compression, DATA equal to the contents of the MISR for Flash block 2 is compressed into the MISR for Flash block 0. 8. If Flash block 3 is selected for compression, DATA equal to the contents of the MISR for Flash block 3 is compressed into the MISR for Flash block 0. 9. The contents of the MISR for Flash block 0 are written to the FDATA registers. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1135 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.2.3 Program Command The program operation will program a previously erased word in the Flash memory using an embedded algorithm. An example flow to execute the program operation is shown in Figure 27-28. The program command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the program command. The data written will be programmed to the address written. Multiple Flash blocks can be simultaneously programmed by writing to the same relative address in each Flash block. 2. Write the program command, 0x20, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the program command. If a word to be programmed is in a protected area of the Flash block, the PVIOL flag in the FSTAT register will set and the program command will not launch. Once the program command has successfully launched, the CCIF flag in the FSTAT register will set after the program operation has completed unless a new command write sequence has been buffered. By executing a new program command write sequence on sequential words after the CBEIF flag in the FSTAT register has been set, up to 55% faster programming time per word can be effectively achieved than by waiting for the CCIF flag to set after each program operation. MC9S12XDP512 Data Sheet, Rev. 2.21 1136 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Address and program Data 1. Simultaneous Multiple Flash Block Decision Next Flash Block? 2. no Write: FCMD register Program Command 0x20 3. Write: FSTAT register Clear CBEIF 0x80 yes Decrement Global Address by 128K Read: FSTAT register Bit Polling for Buffer Empty Check no CBEIF Set? yes Sequential Programming Decision Next Word? yes no Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 27-28. Example Program Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1137 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.2.4 Sector Erase Command The sector erase operation will erase all addresses in a 1 Kbyte sector of Flash memory using an embedded algorithm. An example flow to execute the sector erase operation is shown in Figure 27-29. The sector erase command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the sector erase command. The Flash address written determines the sector to be erased while global address bits [9:0] and the data written are ignored. Multiple Flash sectors can be simultaneously erased by writing to the same relative address in each Flash block. 2. Write the sector erase command, 0x40, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the sector erase command. If a Flash sector to be erased is in a protected area of the Flash block, the PVIOL flag in the FSTAT register will set and the sector erase command will not launch. Once the sector erase command has successfully launched, the CCIF flag in the FSTAT register will set after the sector erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1138 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check 1. Simultaneous Multiple Flash Block Decision ACCERR/ PVIOL Set? no yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Sector Address and Dummy Data Next Flash Block? yes 2. no Write: FCMD register Sector Erase Command 0x40 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 27-29. Example Sector Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1139 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.2.5 Mass Erase Command The mass erase operation will erase all addresses in a Flash block using an embedded algorithm. An example flow to execute the mass erase operation is shown in Figure 27-30. The mass erase command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the mass erase command. The address and data written will be ignored. Multiple Flash blocks can be simultaneously mass erased by writing to the same relative address in each Flash block. 2. Write the mass erase command, 0x41, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the mass erase command. If a Flash block to be erased contains any protected area, the PVIOL flag in the FSTAT register will set and the mass erase command will not launch. Once the mass erase command has successfully launched, the CCIF flag in the FSTAT register will set after the mass erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1140 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check 1. Simultaneous Multiple Flash Block Decision ACCERR/ PVIOL Set? no yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Block Address and Dummy Data Next Flash Block? yes 2. no Write: FCMD register Mass Erase Command 0x41 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 27-30. Example Mass Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1141 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.2.6 Sector Erase Abort Command The sector erase abort operation will terminate the active sector erase operation so that other sectors in a Flash block are available for read and program operations without waiting for the sector erase operation to complete. An example flow to execute the sector erase abort operation is shown in Figure 27-31. The sector erase abort command write sequence is as follows: 1. Write to any Flash block address to start the command write sequence for the sector erase abort command. The address and data written are ignored. 2. Write the sector erase abort command, 0x47, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the sector erase abort command. If the sector erase abort command is launched resulting in the early termination of an active sector erase operation, the ACCERR flag will set once the operation completes as indicated by the CCIF flag being set. The ACCERR flag sets to inform the user that the Flash sector may not be fully erased and a new sector erase command must be launched before programming any location in that specific sector. If the sector erase abort command is launched but the active sector erase operation completes normally, the ACCERR flag will not set upon completion of the operation as indicated by the CCIF flag being set. Therefore, if the ACCERR flag is not set after the sector erase abort command has completed, a Flash sector being erased when the abort command was launched will be fully erased. The maximum number of cycles required to abort a sector erase operation is equal to four FCLK periods (see Section 27.4.1.1, "Writing the FCLKDIV Register") plus five bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. If sectors in multiple Flash blocks are being simultaneously erased, the sector erase abort operation will be applied to all active Flash blocks without writing to each Flash block in the sector erase abort command write sequence. NOTE Since the ACCERR bit in the FSTAT register may be set at the completion of the sector erase abort operation, a command write sequence is not allowed to be buffered behind a sector erase abort command write sequence. The CBEIF flag will not set after launching the sector erase abort command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a sector erase abort operation active, the ACCERR flag in the FSTAT register will be set. A new command write sequence may be started after clearing the ACCERR flag, if set. NOTE The sector erase abort command should be used sparingly since a sector erase operation that is aborted counts as a complete program/erase cycle. MC9S12XDP512 Data Sheet, Rev. 2.21 1142 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) Execute Sector Erase Command Flow Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? Erase Abort Needed? no yes Sector Erase Completed no yes EXIT 1. Write: Dummy Flash Address and Dummy Data 2. Write: FCMD register Sector Erase Abort Cmd 0x47 3. Write: FSTAT register Clear CBEIF 0x80 Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Access Error Check ACCERR Set? yes Write: FSTAT register Clear ACCERR 0x10 no Sector Erase Completed EXIT Sector Erase Aborted EXIT Figure 27-31. Example Sector Erase Abort Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1143 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.4.3 Illegal Flash Operations The ACCERR flag will be set during the command write sequence if any of the following illegal steps are performed, causing the command write sequence to immediately abort: 1. Writing to a Flash address before initializing the FCLKDIV register. 2. Writing a byte or misaligned word to a valid Flash address. 3. Starting a command write sequence while a data compress operation is active. 4. Starting a command write sequence while a sector erase abort operation is active. 5. Writing a Flash address in step 1 of a command write sequence that is not the same relative address as the first one written in the same command write sequence. 6. Writing to any Flash register other than FCMD after writing to a Flash address. 7. Writing a second command to the FCMD register in the same command write sequence. 8. Writing an invalid command to the FCMD register. 9. When security is enabled, writing a command other than mass erase to the FCMD register when the write originates from a non-secure memory location or from the Background Debug Mode. 10. Writing to a Flash address after writing to the FCMD register. 11. Writing to any Flash register other than FSTAT (to clear CBEIF) after writing to the FCMD register. 12. Writing a 0 to the CBEIF flag in the FSTAT register to abort a command write sequence. The ACCERR flag will not be set if any Flash register is read during a valid command write sequence. The ACCERR flag will also be set if any of the following events occur: 1. Launching the sector erase abort command while a sector erase operation is active which results in the early termination of the sector erase operation (see Section 27.4.2.6, "Sector Erase Abort Command"). 2. The MCU enters stop mode and a program or erase operation is in progress. The operation is aborted immediately and any pending command is purged (see Section 27.5.2, "Stop Mode"). If the Flash memory is read during execution of an algorithm (CCIF = 0), the read operation will return invalid data and the ACCERR flag will not be set. If the ACCERR flag is set in the FSTAT register, the user must clear the ACCERR flag before starting another command write sequence (see Section 27.3.2.6, "Flash Status Register (FSTAT)"). The PVIOL flag will be set after the command is written to the FCMD register during a command write sequence if any of the following illegal operations are attempted, causing the command write sequence to immediately abort: 1. Writing the program command if an address written in the command write sequence was in a protected area of the Flash memory 2. Writing the sector erase command if an address written in the command write sequence was in a protected area of the Flash memory 3. Writing the mass erase command to a Flash block while any Flash protection is enabled in the block MC9S12XDP512 Data Sheet, Rev. 2.21 1144 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) If the PVIOL flag is set in the FSTAT register, the user must clear the PVIOL flag before starting another command write sequence (see Section 27.3.2.6, "Flash Status Register (FSTAT)"). 27.5 27.5.1 Operating Modes Wait Mode If a command is active (CCIF = 0) when the MCU enters wait mode, the active command and any buffered command will be completed. The Flash module can recover the MCU from wait mode if the CBEIF and CCIF interrupts are enabled (see Section 27.8, "Interrupts"). 27.5.2 Stop Mode If a command is active (CCIF = 0) when the MCU enters stop mode, the operation will be aborted and, if the operation is program or erase, the Flash array data being programmed or erased may be corrupted and the CCIF and ACCERR flags will be set. If active, the high voltage circuitry to the Flash memory will immediately be switched off when entering stop mode. Upon exit from stop mode, the CBEIF flag is set and any buffered command will not be launched. The ACCERR flag must be cleared before starting a command write sequence (see Section 27.4.1.2, "Command Write Sequence"). NOTE As active commands are immediately aborted when the MCU enters stop mode, it is strongly recommended that the user does not use the STOP instruction during program or erase operations. 27.5.3 Background Debug Mode In background debug mode (BDM), the FPROT register is writable. If the MCU is unsecured, then all Flash commands listed in Table 27-20 can be executed. If the MCU is secured and is in special single chip mode, only mass erase can be executed. 27.6 Flash Module Security The Flash module provides the necessary security information to the MCU. After each reset, the Flash module determines the security state of the MCU as defined in Section 27.3.2.2, "Flash Security Register (FSEC)". The contents of the Flash security byte at 0x7F_FF0F in the Flash Configuration Field must be changed directly by programming 0x7F_FF0F when the MCU is unsecured and the higher address sector is unprotected. If the Flash security byte is left in a secured state, any reset will cause the MCU to initialize to a secure operating mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1145 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) 27.6.1 Unsecuring the MCU using Backdoor Key Access The MCU may be unsecured by using the backdoor key access feature which requires knowledge of the contents of the backdoor keys (four 16-bit words programmed at addresses 0x7F_FF00-0x7F_FF07). If the KEYEN[1:0] bits are in the enabled state (see Section 27.3.2.2, "Flash Security Register (FSEC)") and the KEYACC bit is set, a write to a backdoor key address in the Flash memory triggers a comparison between the written data and the backdoor key data stored in the Flash memory. If all four words of data are written to the correct addresses in the correct order and the data matches the backdoor keys stored in the Flash memory, the MCU will be unsecured. The data must be written to the backdoor keys sequentially starting with 0x7F_FF00-1 and ending with 0x7F_FF06-7. 0x0000 and 0xFFFF are not permitted as backdoor keys. While the KEYACC bit is set, reads of the Flash memory will return invalid data. The user code stored in the Flash memory must have a method of receiving the backdoor keys from an external stimulus. This external stimulus would typically be through one of the on-chip serial ports. If the KEYEN[1:0] bits are in the enabled state (see Section 27.3.2.2, "Flash Security Register (FSEC)"), the MCU can be unsecured by the backdoor key access sequence described below: 1. Set the KEYACC bit in the Flash Configuration Register (FCNFG). 2. Write the correct four 16-bit words to Flash addresses 0xFF00-0xFF07 sequentially starting with 0x7F_FF00. 3. Clear the KEYACC bit. Depending on the user code used to write the backdoor keys, a wait cycle (NOP) may be required before clearing the KEYACC bit. 4. If all four 16-bit words match the backdoor keys stored in Flash addresses 0x7F_FF00-0x7F_FF07, the MCU is unsecured and the SEC[1:0] bits in the FSEC register are forced to the unsecure state of 1:0. The backdoor key access sequence is monitored by an internal security state machine. An illegal operation during the backdoor key access sequence will cause the security state machine to lock, leaving the MCU in the secured state. A reset of the MCU will cause the security state machine to exit the lock state and allow a new backdoor key access sequence to be attempted. The following operations during the backdoor key access sequence will lock the security state machine: 1. If any of the four 16-bit words does not match the backdoor keys programmed in the Flash array. 2. If the four 16-bit words are written in the wrong sequence. 3. If more than four 16-bit words are written. 4. If any of the four 16-bit words written are 0x0000 or 0xFFFF. 5. If the KEYACC bit does not remain set while the four 16-bit words are written. 6. If any two of the four 16-bit words are written on successive MCU clock cycles. After the backdoor keys have been correctly matched, the MCU will be unsecured. Once the MCU is unsecured, the Flash security byte can be programmed to the unsecure state, if desired. In the unsecure state, the user has full control of the contents of the backdoor keys by programming addresses 0x7F_FF00-0x7F_FF07 in the Flash Configuration Field. The security as defined in the Flash security byte (0x7F_FF0F) is not changed by using the backdoor key access sequence to unsecure. The backdoor keys stored in addresses 0x7F_FF00-0x7F_FF07 are MC9S12XDP512 Data Sheet, Rev. 2.21 1146 Freescale Semiconductor Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) unaffected by the backdoor key access sequence. After the next reset of the MCU, the security state of the Flash module is determined by the Flash security byte (0x7F_FF0F). The backdoor key access sequence has no effect on the program and erase protections defined in the Flash protection register. It is not possible to unsecure the MCU in special single chip mode by using the backdoor key access sequence in background debug mode (BDM). 27.6.2 Unsecuring the MCU in Special Single Chip Mode using BDM The MCU can be unsecured in special single chip mode by erasing the Flash module by the following method: * Reset the MCU into special single chip mode, delay while the erase test is performed by the BDM secure ROM, send BDM commands to disable protection in the Flash module, and execute a mass erase command write sequence to erase the Flash memory. After the CCIF flag sets to indicate that the mass operation has completed, reset the MCU into special single chip mode. The BDM secure ROM will verify that the Flash memory is erased and will assert the UNSEC bit in the BDM status register. This BDM action will cause the MCU to override the Flash security state and the MCU will be unsecured. All BDM commands will be enabled and the Flash security byte may be programmed to the unsecure state by the following method: * Send BDM commands to execute a word program sequence to program the Flash security byte to the unsecured state and reset the MCU. 27.7 27.7.1 Resets Flash Reset Sequence On each reset, the Flash module executes a reset sequence to hold CPU activity while loading the following registers from the Flash memory according to Table 27-1: * FPROT -- Flash Protection Register (see Section 27.3.2.5). * FCTL - Flash Control Register (see Section 27.3.2.8). * FSEC -- Flash Security Register (see Section 27.3.2.2). 27.7.2 Reset While Flash Command Active If a reset occurs while any Flash command is in progress, that command will be immediately aborted. The state of the word being programmed or the sector/block being erased is not guaranteed. 27.8 Interrupts The Flash module can generate an interrupt when all Flash command operations have completed, when the Flash address, data and command buffers are empty. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1147 Chapter 27 512 Kbyte Flash Module (S12XFTX512K4V2) Table 27-21. Flash Interrupt Sources Interrupt Source Interrupt Flag Local Enable Global (CCR) Mask Flash Address, Data and Command Buffers empty CBEIF (FSTAT register) CBEIE (FCNFG register) I Bit All Flash commands completed CCIF (FSTAT register) CCIE (FCNFG register) I Bit NOTE Vector addresses and their relative interrupt priority are determined at the MCU level. 27.8.1 Description of Flash Interrupt Operation The logic used for generating interrupts is shown in Figure 27-32. The Flash module uses the CBEIF and CCIF flags in combination with the CBIE and CCIE enable bits to generate the Flash command interrupt request. CBEIF CBEIE Flash Command Interrupt Request CCIF CCIE Figure 27-32. Flash Interrupt Implementation For a detailed description of the register bits, refer to Section 27.3.2.4, "Flash Configuration Register (FCNFG)" and Section 27.3.2.6, "Flash Status Register (FSTAT)" . MC9S12XDP512 Data Sheet, Rev. 2.21 1148 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.1 Introduction This document describes the FTX256K2 module that includes a 256 Kbyte Flash (nonvolatile) memory. The Flash memory may be read as either bytes, aligned words or misaligned words. Read access time is one bus cycle for bytes and aligned words, and two bus cycles for misaligned words. The Flash memory is ideal for program and data storage for single-supply applications allowing for field reprogramming without requiring external voltage sources for program or erase. Program and erase functions are controlled by a command driven interface. The Flash module supports both block erase and sector erase. An erased bit reads 1 and a programmed bit reads 0. The high voltage required to program and erase the Flash memory is generated internally. It is not possible to read from a Flash block while it is being erased or programmed. CAUTION A Flash word must be in the erased state before being programmed. Cumulative programming of bits within a Flash word is not allowed. 28.1.1 Glossary Command Write Sequence -- A three-step MCU instruction sequence to execute built-in algorithms (including program and erase) on the Flash memory. Multiple-Input Signature Register (MISR) -- A Multiple-Input Signature Register is an output response analyzer implemented using a linear feedback shift-register (LFSR). A 16-bit MISR is used to compress data and generate a signature that is particular to the data read from a Flash block. 28.1.2 * * * * * * * * Features 256 Kbytes of Flash memory comprised of two 128 Kbyte blocks with each block divided into 128 sectors of 1024 bytes Automated program and erase algorithm Interrupts on Flash command completion, command buffer empty Fast sector erase and word program operation 2-stage command pipeline for faster multi-word program times Sector erase abort feature for critical interrupt response Flexible protection scheme to prevent accidental program or erase Single power supply for all Flash operations including program and erase MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1149 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) * * Security feature to prevent unauthorized access to the Flash memory Code integrity check using built-in data compression 28.1.3 Modes of Operation Program, erase, erase verify, and data compress operations (please refer to Section 28.4.1, "Flash Command Operations" for details). 28.1.4 Block Diagram A block diagram of the Flash module is shown in Figure 28-1. FTX256K2 Command Interrupt Request Flash Interface Command Pipeline cmd2 addr2 data2_0 data2_1 cmd1 addr1 data1_0 data1_1 Flash Block 0 64K * 16 Bits sector 0 sector 1 sector 127 Registers Protection Security Oscillator Clock Flash Block 1 64K * 16 Bits sector 0 sector 1 sector 127 Clock Divider FCLK Figure 28-1. FTX256K2 Block Diagram 28.2 External Signal Description The Flash module contains no signals that connect off-chip. MC9S12XDP512 Data Sheet, Rev. 2.21 1150 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.3 Memory Map and Register Definition This section describes the memory map and registers for the Flash module. 28.3.1 Module Memory Map The Flash memory map is shown in Figure 28-2. The HCS12X architecture places the Flash memory addresses between global addresses 0x78_0000 and 0x7F_FFFF. The FPROT register, described in Section 28.3.2.5, "Flash Protection Register (FPROT)", can be set to protect regions in the Flash memory from accidental program or erase. Three separate memory regions, one growing upward from global address 0x7F_8000 in the Flash memory (called the lower region), one growing downward from global address 0x7F_FFFF in the Flash memory (called the higher region), and the remaining addresses in the Flash memory, can be activated for protection. The Flash memory addresses covered by these protectable regions are shown in the Flash memory map. The higher address region is mainly targeted to hold the boot loader code since it covers the vector space. The lower address region can be used for EEPROM emulation in an MCU without an EEPROM module since it can be left unprotected while the remaining addresses are protected from program or erase. Default protection settings as well as security information that allows the MCU to restrict access to the Flash module are stored in the Flash configuration field as described in Table 28-1. Table 28-1. Flash Configuration Field Global Address Size (Bytes) 0x7F_FF00 - 0x7F_FF07 8 Backdoor Comparison Key Refer to Section 28.6.1, "Unsecuring the MCU using Backdoor Key Access" 0x7F_FF08 - 0x7F_FF0C 5 Reserved 0x7F_FF0D 1 Flash Protection byte Refer to Section 28.3.2.5, "Flash Protection Register (FPROT)" 0x7F_FF0E 1 Flash Nonvolatile byte Refer to Section 28.3.2.8, "Flash Control Register (FCTL)" 0x7F_FF0F 1 Flash Security byte Refer to Section 28.3.2.2, "Flash Security Register (FSEC)" Description MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1151 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) MODULE BASE + 0x0000 MODULE BASE + 0x000F Flash Registers 16 bytes FLASH START = 0x78_0000 Flash Protected/Unprotected Region 128 Kbytes 0x79_FFFF Unimplemented Flash Region 256 Kbytes 0x7E_0000 Flash Protected/Unprotected Region 96 Kbytes 0x7F_8000 0x7F_8400 0x7F_8800 0x7F_9000 Flash Protected/Unprotected Lower Region 1, 2, 4, 8 Kbytes 0x7F_A000 Flash Protected/Unprotected Region 8 Kbytes (up to 29 Kbytes) 0x7F_C000 0x7F_E000 Flash Protected/Unprotected Higher Region 2, 4, 8, 16 Kbytes 0x7F_F000 0x7F_F800 FLASH END = 0x7F_FFFF Flash Configuration Field 16 bytes (0x7F_FF00 - 0x7F_FF0F) Figure 28-2. Flash Memory Map MC9S12XDP512 Data Sheet, Rev. 2.21 1152 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.3.2 Register Descriptions The Flash module contains a set of 16 control and status registers located between module base + 0x0000 and 0x000F. A summary of the Flash module registers is given in Figure 28-3. Detailed descriptions of each register bit are provided. Register Name FCLKDIV Bit 7 R 6 5 4 3 2 1 Bit 0 PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0 RNV5 RNV4 RNV3 RNV2 0 0 0 0 0 0 0 0 0 0 FDIVLD W FSEC R KEYEN SEC W FTSTMOD R 0 MRDS W FCNFG R CBEIE CCIE KEYACC W FPROT R RNV6 FPOPEN FPHDIS FPHS FPLDIS FPLS W FSTAT R CCIF CBEIF 0 PVIOL BLANK 0 0 NV2 NV1 NV0 ACCERR W FCMD R 0 CMDB W FCTL R 0 NV6 NV5 NV4 NV3 W FADDRHI R FADDRHI W FADDRLO R FADDRLO W FDATAHI R FDATAHI W FDATALO R FDATALO W Figure 28-3. FTX256K2 Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1153 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) Register Name RESERVED1 R Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W RESERVED2 R W RESERVED3 R W RESERVED4 R W Figure 28-3. FTX256K2 Register Summary (continued) 28.3.2.1 Flash Clock Divider Register (FCLKDIV) The FCLKDIV register is used to control timed events in program and erase algorithms. 7 R 6 5 4 3 2 1 0 PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0 0 0 0 0 0 0 0 FDIVLD W Reset 0 = Unimplemented or Reserved Figure 28-4. Flash Clock Divider Register (FCLKDIV) All bits in the FCLKDIV register are readable, bits 6-0 are write once and bit 7 is not writable. Table 28-2. FCLKDIV Field Descriptions Field Description 7 FDIVLD Clock Divider Loaded. 0 Register has not been written. 1 Register has been written to since the last reset. 6 PRDIV8 Enable Prescalar by 8. 0 The oscillator clock is directly fed into the clock divider. 1 The oscillator clock is divided by 8 before feeding into the clock divider. 5:0 FDIV[5:0] 28.3.2.2 Clock Divider Bits -- The combination of PRDIV8 and FDIV[5:0] must divide the oscillator clock down to a frequency of 150 kHz-200 kHz. The maximum divide ratio is 512. Please refer to Section 28.4.1.1, "Writing the FCLKDIV Register" for more information. Flash Security Register (FSEC) The FSEC register holds all bits associated with the security of the MCU and Flash module. MC9S12XDP512 Data Sheet, Rev. 2.21 1154 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 7 R 6 KEYEN 5 4 3 2 RNV5 RNV4 RNV3 RNV2 F F F F 1 0 SEC W Reset F F F F = Unimplemented or Reserved Figure 28-5. Flash Security Register (FSEC) All bits in the FSEC register are readable but are not writable. The FSEC register is loaded from the Flash Configuration Field at address 0x7F_FF0F during the reset sequence, indicated by F in Figure 28-5. Table 28-3. FSEC Field Descriptions Field Description 7:6 Backdoor Key Security Enable Bits -- The KEYEN[1:0] bits define the enabling of backdoor key access to the KEYEN[1:0] Flash module as shown in Table 28-4. 5:2 RNV[5:2] Reserved Nonvolatile Bits -- The RNV[5:2] bits should remain in the erased state for future enhancements. 1:0 SEC[1:0] Flash Security Bits -- The SEC[1:0] bits define the security state of the MCU as shown in Table 28-5. If the Flash module is unsecured using backdoor key access, the SEC[1:0] bits are forced to 1:0. Table 28-4. Flash KEYEN States KEYEN[1:0] Status of Backdoor Key Access 00 DISABLED 011 DISABLED 10 ENABLED 11 DISABLED 1 Preferred KEYEN state to disable Backdoor Key Access. Table 28-5. Flash Security States SEC[1:0] Status of Security 00 SECURED 1 SECURED 01 10 UNSECURED 11 SECURED 1 Preferred SEC state to set MCU to secured state. The security function in the Flash module is described in Section 28.6, "Flash Module Security". 28.3.2.3 Flash Test Mode Register (FTSTMOD) The FTSTMOD register is used to control Flash test features. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1155 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 7 R 6 5 0 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 MRDS W Reset 0 0 0 = Unimplemented or Reserved Figure 28-6. Flash Test Mode Register (FTSTMOD --Normal Mode) 7 R 6 5 4 0 MRDS 3 2 1 0 0 0 0 0 0 0 0 0 WRALL W Reset 0 0 0 0 = Unimplemented or Reserved Figure 28-7. Flash Test Mode Register (FTSTMOD -- Special Mode) MRDS bits are readable and writable while all remaining bits read 0 and are not writable in normal mode. The WRALL bit is writable only in special mode to simplify mass erase and erase verify operations. When writing to the FTSTMOD register in special mode, all unimplemented/reserved bits must be written to 0. Table 28-6. FTSTMOD Field Descriptions Field Description 6:5 MRDS[1:0] Margin Read Setting -- The MRDS[1:0] bits are used to set the sense-amp margin level for reads of the Flash array as shown in Table 28-7. 4 WRALL Write to all Register Banks -- If the WRALL bit is set, all banked FDATA registers sharing the same register address will be written simultaneously during a register write. 0 Write only to the FDATA register bank selected using BKSEL. 1 Write to all FDATA register banks. Table 28-7. FTSTMOD Margin Read Settings MRDS[1:0] Margin Read Setting 00 Normal 01 Program Margin1 10 Erase Margin2 11 Normal 1 Flash array reads will be sensitive to program margin. 2 Flash array reads will be sensitive to erase margin. 28.3.2.4 Flash Configuration Register (FCNFG) The FCNFG register enables the Flash interrupts and gates the security backdoor writes. MC9S12XDP512 Data Sheet, Rev. 2.21 1156 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 7 6 5 CBEIE CCIE KEYACC 0 0 0 R 4 3 2 1 0 Undefined 0 0 0 0 Undefined 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 28-8. Flash Configuration Register (FCNFG -- Normal Mode) 7 6 5 R CBEIE CCIE KEYACC 0 0 0 4 3 2 1 0 0 0 0 BKSEL W Reset 0 0 0 0 0 = Unimplemented or Reserved Figure 28-9. Flash Configuration Register (FCNFG -- Special Mode) CBEIE, CCIE and KEYACC bits are readable and writable while all remaining bits read 0 and are not writable in normal mode. KEYACC is only writable if KEYEN (see Section 28.3.2.2, "Flash Security Register (FSEC)" is set to the enabled state. BKSEL is readable and writable in special mode to simplify mass erase and erase verify operations. When writing to the FCNFG register in special mode, all unimplemented/ reserved bits must be written to 0. Table 28-8. FCNFG Field Descriptions Field Description 7 CBEIE Command Buffer Empty Interrupt Enable -- The CBEIE bit enables an interrupt in case of an empty command buffer in the Flash module. 0 Command buffer empty interrupt disabled. 1 An interrupt will be requested whenever the CBEIF flag (see Section 28.3.2.6, "Flash Status Register (FSTAT)") is set. 6 CCIE Command Complete Interrupt Enable -- The CCIE bit enables an interrupt in case all commands have been completed in the Flash module. 0 Command complete interrupt disabled. 1 An interrupt will be requested whenever the CCIF flag (see Section 28.3.2.6, "Flash Status Register (FSTAT)") is set. 5 KEYACC 0 BKSEL 28.3.2.5 Enable Security Key Writing 0 Flash writes are interpreted as the start of a command write sequence. 1 Writes to Flash array are interpreted as keys to open the backdoor. Reads of the Flash array return invalid data. Block Select -- The BKSEL bit indicates which register bank is active. 0 Select register bank associated with Flash block 0. 1 Select register bank associated with Flash block 1. Flash Protection Register (FPROT) The FPROT register defines which Flash sectors are protected against program or erase operations. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1157 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 7 R 6 5 4 3 2 1 0 RNV6 FPOPEN FPHDIS FPHS FPLDIS FPLS W Reset F F F F F F F F = Unimplemented or Reserved Figure 28-10. Flash Protection Register (FPROT) All bits in the FPROT register are readable and writable with restrictions (see Section 28.3.2.5.1, "Flash Protection Restrictions") except for RNV[6] which is only readable. During the reset sequence, the FPROT register is loaded from the Flash Configuration Field at global address 0x7F_FF0D. To change the Flash protection that will be loaded during the reset sequence, the upper sector of the Flash memory must be unprotected, then the Flash Protect/Security byte located as described in Table 28-1 must be reprogrammed. Trying to alter data in any protected area in the Flash memory will result in a protection violation error and the PVIOL flag will be set in the FSTAT register. The mass erase of a Flash block is not possible if any of the Flash sectors contained in the Flash block are protected. Table 28-9. FPROT Field Descriptions Field Description 7 FPOPEN Flash Protection Open -- The FPOPEN bit determines the protection function for program or erase as shown in Table 28-10. 0 The FPHDIS and FPLDIS bits define unprotected address ranges as specified by the corresponding FPHS[1:0] and FPLS[1:0] bits. For an MCU without an EEPROM module, the FPOPEN clear state allows the main part of the Flash block to be protected while a small address range can remain unprotected for EEPROM emulation. 1 The FPHDIS and FPLDIS bits enable protection for the address range specified by the corresponding FPHS[1:0] and FPLS[1:0] bits. 6 RNV6 5 FPHDIS Reserved Nonvolatile Bit -- The RNV[6] bit should remain in the erased state for future enhancements. Flash Protection Higher Address Range Disable -- The FPHDIS bit determines whether there is a protected/unprotected area in a specific region of the Flash memory ending with global address 0x7F_FFFF. 0 Protection/Unprotection enabled. 1 Protection/Unprotection disabled. 4:3 FPHS[1:0] Flash Protection Higher Address Size -- The FPHS[1:0] bits determine the size of the protected/unprotected area as shown inTable 28-11. The FPHS[1:0] bits can only be written to while the FPHDIS bit is set. 2 FPLDIS Flash Protection Lower Address Range Disable -- The FPLDIS bit determines whether there is a protected/unprotected area in a specific region of the Flash memory beginning with global address 0x7F_8000. 0 Protection/Unprotection enabled. 1 Protection/Unprotection disabled. 1:0 FPLS[1:0] Flash Protection Lower Address Size -- The FPLS[1:0] bits determine the size of the protected/unprotected area as shown in Table 28-12. The FPLS[1:0] bits can only be written to while the FPLDIS bit is set. MC9S12XDP512 Data Sheet, Rev. 2.21 1158 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) Table 28-10. Flash Protection Function Function1 FPOPEN FPHDIS FPLDIS 1 1 1 No Protection 1 1 0 Protected Low Range 1 0 1 Protected High Range 1 0 0 Protected High and Low Ranges 0 1 1 Full Flash memory Protected 0 1 0 Unprotected Low Range 0 0 1 Unprotected High Range 0 0 0 Unprotected High and Low Ranges 1 For range sizes, refer to Table 28-11 and Table 28-12. Table 28-11. Flash Protection Higher Address Range FPHS[1:0] Global Address Range Protected Size 00 0x7F_F800-0x7F_FFFF 2 Kbytes 01 0x7F_F000-0x7F_FFFF 4 Kbytes 10 0x7F_E000-0x7F_FFFF 8 Kbytes 11 0x7F_C000-0x7F_FFFF 16 Kbytes Table 28-12. Flash Protection Lower Address Range FPLS[1:0] Global Address Range Protected Size 00 0x7F_8000-0x7F_83FF 1 Kbytes 01 0x7F_8000-0x7F_87FF 2 Kbytes 10 0x7F_8000-0x7F_8FFF 4 Kbytes 11 0x7F_8000-0x7F_9FFF 8 Kbytes All possible Flash protection scenarios are shown in Figure 28-11. Although the protection scheme is loaded from the Flash array at global address 0x7F_FF0D during the reset sequence, it can be changed by the user. This protection scheme can be used by applications requiring re-programming in single chip mode while providing as much protection as possible if re-programming is not required. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1159 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 0x78_0000 FPHDIS=1 FPLDIS=1 FPHDIS=1 FPLDIS=0 FPHDIS=0 FPLDIS=1 FPHDIS=0 FPLDIS=0 7 6 5 4 Scenario 0x7F_8000 FPLS[1:0] FPOPEN=1 FPHS[1:0] 0x7F_FFFF 3 2 Scenario 1 0 0x78_0000 0x7F_8000 FPLS[1:0] FPOPEN=0 FPHS[1:0] 0x7F_FFFF Unprotected region Protected region with size defined by FPLS Protected region not defined by FPLS, FPHS Protected region with size defined by FPHS Figure 28-11. Flash Protection Scenarios MC9S12XDP512 Data Sheet, Rev. 2.21 1160 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.3.2.5.1 Flash Protection Restrictions The general guideline is that Flash protection can only be added and not removed. Table 28-13 specifies all valid transitions between Flash protection scenarios. Any attempt to write an invalid scenario to the FPROT register will be ignored and the FPROT register will remain unchanged. The contents of the FPROT register reflect the active protection scenario. See the FPHS and FPLS descriptions for additional restrictions. Table 28-13. Flash Protection Scenario Transitions To Protection Scenario1 From Protection Scenario 0 1 2 3 0 X X X X 1 X 2 4 X 4 X X X X X X X X X X 7 X X 7 X 3 6 6 X X 5 5 X X X X X X 1 Allowed transitions marked with X. 28.3.2.6 Flash Status Register (FSTAT) The FSTAT register defines the operational status of the module. 7 6 R 5 4 PVIOL ACCERR 0 0 CCIF CBEIF 3 2 1 0 0 BLANK 0 0 0 0 0 0 W Reset 1 1 = Unimplemented or Reserved Figure 28-12. Flash Status Register (FSTAT -- Normal Mode) 7 6 R 5 4 CCIF CBEIF PVIOL ACCERR 0 0 3 2 0 BLANK 1 0 0 FAIL W Reset 1 1 0 0 0 0 = Unimplemented or Reserved Figure 28-13. Flash Status Register (FSTAT -- Special Mode) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1161 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) CBEIF, PVIOL, and ACCERR are readable and writable, CCIF and BLANK are readable and not writable, remaining bits read 0 and are not writable in normal mode. FAIL is readable and writable in special mode. FAIL must be clear in special mode when starting a command write sequence. Table 28-14. FSTAT Field Descriptions Field Description 7 CBEIF Command Buffer Empty Interrupt Flag -- The CBEIF flag indicates that the address, data and command buffers are empty so that a new command write sequence can be started. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned word to the Flash address space, but before CBEIF is cleared, will abort a command write sequence and cause the ACCERR flag to be set. Writing a 0 to CBEIF outside of a command write sequence will not set the ACCERR flag. The CBEIF flag is cleared by writing a 1 to CBEIF. The CBEIF flag is used together with the CBEIE bit in the FCNFG register to generate an interrupt request (see Figure 28-32). 0 Command buffers are full. 1 Command buffers are ready to accept a new command. 6 CCIF Command Complete Interrupt Flag -- The CCIF flag indicates that there are no more commands pending. The CCIF flag is cleared when CBEIF is cleared and sets automatically upon completion of all active and pending commands. The CCIF flag does not set when an active commands completes and a pending command is fetched from the command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together with the CCIE bit in the FCNFG register to generate an interrupt request (see Figure 28-32). 0 Command in progress. 1 All commands are completed. 5 PVIOL Protection Violation Flag --The PVIOL flag indicates an attempt was made to program or erase an address in a protected area of the Flash memory during a command write sequence. Writing a 0 to the PVIOL flag has no effect on PVIOL. The PVIOL flag is cleared by writing a 1 to PVIOL. While PVIOL is set, it is not possible to launch a command or start a command write sequence. 0 No protection violation detected. 1 Protection violation has occurred. 4 ACCERR Access Error Flag -- The ACCERR flag indicates an illegal access has occurred to the Flash memory caused by either a violation of the command write sequence (see Section 28.4.1.2, "Command Write Sequence"), issuing an illegal Flash command (see Table 28-16), launching the sector erase abort command terminating a sector erase operation early (see Section 28.4.2.6, "Sector Erase Abort Command") or the execution of a CPU STOP instruction while a command is executing (CCIF = 0). Writing a 0 to the ACCERR flag has no effect on ACCERR. The ACCERR flag is cleared by writing a 1 to ACCERR.While ACCERR is set, it is not possible to launch a command or start a command write sequence. If ACCERR is set by an erase verify operation or a data compress operation, any buffered command will not launch. 0 No access error detected. 1 Access error has occurred. 2 BLANK Flag Indicating the Erase Verify Operation Status -- When the CCIF flag is set after completion of an erase verify command, the BLANK flag indicates the result of the erase verify operation. The BLANK flag is cleared by the Flash module when CBEIF is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect on BLANK. 0 Flash block verified as not erased. 1 Flash block verified as erased. 1 FAIL Flag Indicating a Failed Flash Operation -- The FAIL flag will set if the erase verify operation fails (selected Flash block verified as not erased). Writing a 0 to the FAIL flag has no effect on FAIL. The FAIL flag is cleared by writing a 1 to FAIL. 0 Flash operation completed without error. 1 Flash operation failed. MC9S12XDP512 Data Sheet, Rev. 2.21 1162 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.3.2.7 Flash Command Register (FCMD) The FCMD register is the Flash command register. 7 R 6 5 4 3 2 1 0 0 0 0 0 CMDB W Reset 1 1 0 0 0 = Unimplemented or Reserved Figure 28-14. Flash Command Register (FCMD) All CMDB bits are readable and writable during a command write sequence while bit 7 reads 0 and is not writable. Table 28-15. FCMD Field Descriptions Field Description 6:0 CMDB[6:0] Flash Command -- Valid Flash commands are shown in Table 28-16. Writing any command other than those listed in Table 28-16 sets the ACCERR flag in the FSTAT register. Table 28-16. Valid Flash Command List 28.3.2.8 CMDB[6:0] NVM Command 0x05 Erase Verify 0x06 Data Compress 0x20 Word Program 0x40 Sector Erase 0x41 Mass Erase 0x47 Sector Erase Abort Flash Control Register (FCTL) The FCTL register is the Flash control register. R 7 6 5 4 3 2 1 0 0 NV6 NV5 NV4 NV3 NV2 NV1 NV0 0 F F F F F F F W Reset = Unimplemented or Reserved Figure 28-15. Flash Control Register (FCTL) All bits in the FCTL register are readable but are not writable. The FCTL NV bits are loaded from the Flash nonvolatile byte located at global address 0x7F_FF0E during the reset sequence, indicated by F in Figure 28-15. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1163 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) Table 28-17. FCTL Field Descriptions Field Description 6:0 NV[6:0] Nonvolatile Bits -- The NV[6:0] bits are available as nonvolatile bits. Refer to the Device User Guide for proper use of the NV bits. 28.3.2.9 Flash Address Registers (FADDR) The FADDRHI and FADDRLO registers are the Flash address registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 FADDRHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 28-16. Flash Address High Register (FADDRHI) 7 6 5 4 R 3 2 1 0 0 0 0 0 FADDRLO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 28-17. Flash Address Low Register (FADDRLO) All FADDRHI and FADDRLO bits are readable but are not writable. After an array write as part of a command write sequence, the FADDR registers will contain the mapped MCU address written. 28.3.2.10 Flash Data Registers (FDATA) The FDATAHI and FDATALO registers are the Flash data registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 FDATAHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 28-18. Flash Data High Register (FDATAHI) MC9S12XDP512 Data Sheet, Rev. 2.21 1164 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 7 6 5 4 R 3 2 1 0 0 0 0 0 FDATALO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 28-19. Flash Data Low Register (FDATALO) All FDATAHI and FDATALO bits are readable but are not writable. At the completion of a data compress operation, the resulting 16-bit signature is stored in the FDATA registers. The data compression signature is readable in the FDATA registers until a new command write sequence is started. 28.3.2.11 RESERVED1 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 28-20. RESERVED1 All bits read 0 and are not writable. 28.3.2.12 RESERVED2 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 28-21. RESERVED2 All bits read 0 and are not writable. 28.3.2.13 RESERVED3 This register is reserved for factory testing and is not accessible. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1165 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 28-22. RESERVED3 All bits read 0 and are not writable. 28.3.2.14 RESERVED4 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 28-23. RESERVED4 All bits read 0 and are not writable. 28.4 28.4.1 Functional Description Flash Command Operations Write operations are used to execute program, erase, erase verify, erase abort, and data compress algorithms described in this section. The program and erase algorithms are controlled by a state machine whose timebase, FCLK, is derived from the oscillator clock via a programmable divider. The command register, as well as the associated address and data registers, operate as a buffer and a register (2-stage FIFO) so that a second command along with the necessary data and address can be stored to the buffer while the first command is still in progress. This pipelined operation allows a time optimization when programming more than one word on a specific row in the Flash block as the high voltage generation can be kept active in between two programming commands. The pipelined operation also allows a simplification of command launching. Buffer empty as well as command completion are signalled by flags in the Flash status register with corresponding interrupts generated, if enabled. The next sections describe: 1. How to write the FCLKDIV register 2. Command write sequences to program, erase, erase verify, erase abort, and data compress operations on the Flash memory 3. Valid Flash commands 4. Effects resulting from illegal Flash command write sequences or aborting Flash operations MC9S12XDP512 Data Sheet, Rev. 2.21 1166 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.1.1 Writing the FCLKDIV Register Prior to issuing any Flash command after a reset, the user is required to write the FCLKDIV register to divide the oscillator clock down to within the 150 kHz to 200 kHz range. Since the program and erase timings are also a function of the bus clock, the FCLKDIV determination must take this information into account. If we define: * FCLK as the clock of the Flash timing control block * Tbus as the period of the bus clock * INT(x) as taking the integer part of x (e.g. INT(4.323) = 4) then FCLKDIV register bits PRDIV8 and FDIV[5:0] are to be set as described in Figure 28-24. For example, if the oscillator clock frequency is 950kHz and the bus clock frequency is 10MHz, FCLKDIV bits FDIV[5:0] should be set to 0x04 (000100) and bit PRDIV8 set to 0. The resulting FCLK frequency is then 190kHz. As a result, the Flash program and erase algorithm timings are increased over the optimum target by: ( 200 - 190 ) 200 x 100 = 5% If the oscillator clock frequency is 16MHz and the bus clock frequency is 40MHz, FCLKDIV bits FDIV[5:0] should be set to 0x0A (001010) and bit PRDIV8 set to 1. The resulting FCLK frequency is then 182kHz. In this case, the Flash program and erase algorithm timings are increased over the optimum target by: ( 200 - 182 ) 200 x 100 = 9% CAUTION Program and erase command execution time will increase proportionally with the period of FCLK. Because of the impact of clock synchronization on the accuracy of the functional timings, programming or erasing the Flash memory cannot be performed if the bus clock runs at less than 1 MHz. Programming or erasing the Flash memory with FCLK < 150 kHz should be avoided. Setting FCLKDIV to a value such that FCLK < 150 kHz can destroy the Flash memory due to overstress. Setting FCLKDIV to a value such that (1/FCLK+Tbus) < 5s can result in incomplete programming or erasure of the Flash memory cells. If the FCLKDIV register is written, the FDIVLD bit is set automatically. If the FDIVLD bit is 0, the FCLKDIV register has not been written since the last reset. If the FCLKDIV register has not been written to, the Flash command loaded during a command write sequence will not execute and the ACCERR flag in the FSTAT register will set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1167 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) START Tbus < 1s? no ALL COMMANDS IMPOSSIBLE yes PRDIV8=0 (reset) oscillator_clock 12.8MHz? no yes PRDIV8=1 PRDCLK=oscillator_clock/8 PRDCLK[MHz]*(5+Tbus[s]) an integer? yes PRDCLK=oscillator_clock no FDIV[5:0]=INT(PRDCLK[MHz]*(5+Tbus[s])) FDIV[5:0]=PRDCLK[MHz]*(5+Tbus[s])-1 TRY TO DECREASE Tbus FCLK=(PRDCLK)/(1+FDIV[5:0]) 1/FCLK[MHz] + Tbus[s] > 5 AND FCLK > 0.15MHz ? yes END no yes FDIV[5:0] > 4? no ALL COMMANDS IMPOSSIBLE Figure 28-24. Determination Procedure for PRDIV8 and FDIV Bits MC9S12XDP512 Data Sheet, Rev. 2.21 1168 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.1.2 Command Write Sequence The Flash command controller is used to supervise the command write sequence to execute program, erase, erase verify, erase abort, and data compress algorithms. Before starting a command write sequence, the ACCERR and PVIOL flags in the FSTAT register must be clear (see Section 28.3.2.6, "Flash Status Register (FSTAT)") and the CBEIF flag should be tested to determine the state of the address, data and command buffers. If the CBEIF flag is set, indicating the buffers are empty, a new command write sequence can be started. If the CBEIF flag is clear, indicating the buffers are not available, a new command write sequence will overwrite the contents of the address, data and command buffers. A command write sequence consists of three steps which must be strictly adhered to with writes to the Flash module not permitted between the steps. However, Flash register and array reads are allowed during a command write sequence. The basic command write sequence is as follows: 1. Write to a valid address in the Flash memory. Addresses in multiple Flash blocks can be written to as long as the location is at the same relative address in each available Flash block. Multiple addresses must be written in Flash block order starting with the lower Flash block. 2. Write a valid command to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the command. The address written in step 1 will be stored in the FADDR registers and the data will be stored in the FDATA registers. If the CBEIF flag in the FSTAT register is clear when the first Flash array write occurs, the contents of the address and data buffers will be overwritten and the CBEIF flag will be set. When the CBEIF flag is cleared, the CCIF flag is cleared on the same bus cycle by the Flash command controller indicating that the command was successfully launched. For all command write sequences except data compress and sector erase abort, the CBEIF flag will set four bus cycles after the CCIF flag is cleared indicating that the address, data, and command buffers are ready for a new command write sequence to begin. For data compress and sector erase abort operations, the CBEIF flag will remain clear until the operation completes. Except for the sector erase abort command, a buffered command will wait for the active operation to be completed before being launched. The sector erase abort command is launched when the CBEIF flag is cleared as part of a sector erase abort command write sequence. Once a command is launched, the completion of the command operation is indicated by the setting of the CCIF flag in the FSTAT register. The CCIF flag will set upon completion of all active and buffered commands. 28.4.2 Flash Commands Table 28-18 summarizes the valid Flash commands along with the effects of the commands on the Flash block. Table 28-18. Flash Command Description FCMDB 0x05 NVM Command Erase Verify Function on Flash Memory Verify all memory bytes in the Flash block are erased. If the Flash block is erased, the BLANK flag in the FSTAT register will set upon command completion. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1169 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) Table 28-18. Flash Command Description NVM Command Function on Flash Memory 0x06 Data Compress Compress data from a selected portion of the Flash block. The resulting signature is stored in the FDATA register. 0x20 Program 0x40 Sector Erase Erase all memory bytes in a sector of the Flash block. 0x41 Mass Erase Erase all memory bytes in the Flash block. A mass erase of the full Flash block is only possible when FPLDIS, FPHDIS and FPOPEN bits in the FPROT register are set prior to launching the command. 0x47 Sector Erase Abort Abort the sector erase operation. The sector erase operation will terminate according to a set procedure. The Flash sector should not be considered erased if the ACCERR flag is set upon command completion. FCMDB Program a word (two bytes) in the Flash block. CAUTION A Flash word must be in the erased state before being programmed. Cumulative programming of bits within a Flash word is not allowed. MC9S12XDP512 Data Sheet, Rev. 2.21 1170 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.2.1 Erase Verify Command The erase verify operation will verify that a Flash block is erased. An example flow to execute the erase verify operation is shown in Figure 28-25. The erase verify command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the erase verify command. The address and data written will be ignored. Multiple Flash blocks can be simultaneously erase verified by writing to the same relative address in each Flash block. 2. Write the erase verify command, 0x05, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the erase verify command. After launching the erase verify command, the CCIF flag in the FSTAT register will set after the operation has completed unless a new command write sequence has been buffered. The number of bus cycles required to execute the erase verify operation is equal to the number of addresses in a Flash block plus 14 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Upon completion of the erase verify operation, the BLANK flag in the FSTAT register will be set if all addresses in the selected Flash blocks are verified to be erased. If any address in a selected Flash block is not erased, the erase verify operation will terminate and the BLANK flag in the FSTAT register will remain clear. The MRDS bits in the FTSTMOD register will determine the sense-amp margin setting during the erase verify operation. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1171 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check 1. Simultaneous Multiple Flash Block Decision ACCERR/ PVIOL Set? no yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Block Address and Dummy Data Next Flash Block? yes 2. no Write: FCMD register Erase Verify Command 0x05 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K (skip unimplemented Flash) Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Erase Verify Status BLANK Set? no yes EXIT Flash Block Erased EXIT Flash Block Not Erased Figure 28-25. Example Erase Verify Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1172 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.2.2 Data Compress Command The data compress operation will check Flash code integrity by compressing data from a selected portion of the Flash memory into a signature analyzer. An example flow to execute the data compress operation is shown in Figure 28-26. The data compress command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the data compress command. The address written determines the starting address for the data compress operation and the data written determines the number of consecutive words to compress. If the data value written is 0x0000, 64K addresses or 128 Kbytes will be compressed. Multiple Flash blocks can be simultaneously compressed by writing to the same relative address in each Flash block. If more than one Flash block is written to in this step, the first data written will determine the number of consecutive words to compress in each selected Flash block. 2. Write the data compress command, 0x06, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the data compress command. After launching the data compress command, the CCIF flag in the FSTAT register will set after the data compress operation has completed. The number of bus cycles required to execute the data compress operation is equal to two times the number of consecutive words to compress plus the number of Flash blocks simultaneously compressed plus 18 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Once the CCIF flag is set, the signature generated by the data compress operation is available in the FDATA registers. The signature in the FDATA registers can be compared to the expected signature to determine the integrity of the selected data stored in the selected Flash memory. If the last address of a Flash block is reached during the data compress operation, data compression will continue with the starting address of the same Flash block. The MRDS bits in the FTSTMOD register will determine the sense-amp margin setting during the data compress operation. NOTE Since the FDATA registers (or data buffer) are written to as part of the data compress operation, a command write sequence is not allowed to be buffered behind a data compress command write sequence. The CBEIF flag will not set after launching the data compress command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a data compress operation active, the ACCERR flag in the FSTAT register will be set. A new command write sequence should only be started after reading the signature stored in the FDATA registers. In order to take corrective action, it is recommended that the data compress command be executed on a Flash sector or subset of a Flash sector. If the data compress operation on a Flash sector returns an invalid signature, the Flash sector should be erased using the sector erase command and then reprogrammed using the program command. The data compress command can be used to verify that a sector or sequential set of sectors are erased. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1173 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Address to start compression and number of word addresses to compress 1. NOTE: address used to select Flash block; data ignored. Simultaneous Multiple Flash Block Decision Next Flash Block? yes 2. no Write: FCMD register Data Compress Command 0x06 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K (skip unimplemented Flash) Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Read: FDATA registers Data Compress Signature Signature Valid? no Erase and Reprogram Flash Sector(s) Compressed yes EXIT Figure 28-26. Example Data Compress Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1174 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.2.2.1 Data Compress Operation The Flash module contains a 16-bit multiple-input signature register (MISR) for each Flash block to generate a 16-bit signature based on selected Flash array data. If multiple Flash blocks are selected for simultaneous compression, then the signature from each Flash block is further compressed to generate a single 16-bit signature. The final 16-bit signature, found in the FDATA registers after the data compress operation has completed, is based on the following logic equation which is executed on every data compression cycle during the operation: MISR[15:0] = {MISR[14:0], ^MISR[15,4,2,1]} ^ DATA[15:0] Eqn. 28-1 where MISR is the content of the internal signature register associated with each Flash block and DATA is the data to be compressed as shown in Figure 28-27. DATA[0] + DATA[1] DQ DATA[2] + M0 > + DQ M1 > DATA[3] + DQ M2 > + DATA[4] DQ M3 > + + DATA[5] + DQ M4 > DATA[15] DQ M5 > ... + DQ M15 > + + = Exclusive-OR MISR[15:0] = Q[15:0] Figure 28-27. 16-Bit MISR Diagram During the data compress operation, the following steps are executed: 1. MISR for each Flash block is reset to 0xFFFF. 2. Initialized DATA equal to 0xFFFF is compressed into the MISR for each selected Flash block which results in the MISR containing 0x0001. 3. DATA equal to the selected Flash array data range is read and compressed into the MISR for each selected Flash block with addresses incrementing. 4. DATA equal to the selected Flash array data range is read and compressed into the MISR for each selected Flash block with addresses decrementing. 5. If Flash block 0 is selected for compression, DATA equal to the contents of the MISR for Flash block 0 is compressed into the MISR for Flash block 0. If data in Flash block 0 was not selected for compression, the MISR for Flash block 0 contains 0xFFFF. 6. If Flash block 1 is selected for compression, DATA equal to the contents of the MISR for Flash block 1 is compressed into the MISR for Flash block 0. 7. If Flash block 2 is selected for compression, DATA equal to the contents of the MISR for Flash block 2 is compressed into the MISR for Flash block 0. 8. If Flash block 3 is selected for compression, DATA equal to the contents of the MISR for Flash block 3 is compressed into the MISR for Flash block 0. 9. If Flash block 4 is selected for compression, DATA equal to the contents of the MISR for Flash block 4 is compressed into the MISR for Flash block 0. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1175 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 10. If Flash block 5 is selected for compression, DATA equal to the contents of the MISR for Flash block 5 is compressed into the MISR for Flash block 0. 11. If Flash block 6 is selected for compression, DATA equal to the contents of the MISR for Flash block 6 is compressed into the MISR for Flash block 0. 12. If Flash block 7 is selected for compression, DATA equal to the contents of the MISR for Flash block 7 is compressed into the MISR for Flash block 0. 13. The contents of the MISR for Flash block 0 are written to the FDATA registers. MC9S12XDP512 Data Sheet, Rev. 2.21 1176 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.2.3 Program Command The program operation will program a previously erased word in the Flash memory using an embedded algorithm. An example flow to execute the program operation is shown in Figure 28-28. The program command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the program command. The data written will be programmed to the address written. Multiple Flash blocks can be simultaneously programmed by writing to the same relative address in each Flash block. 2. Write the program command, 0x20, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the program command. If a word to be programmed is in a protected area of the Flash block, the PVIOL flag in the FSTAT register will set and the program command will not launch. Once the program command has successfully launched, the CCIF flag in the FSTAT register will set after the program operation has completed unless a new command write sequence has been buffered. By executing a new program command write sequence on sequential words after the CBEIF flag in the FSTAT register has been set, up to 55% faster programming time per word can be effectively achieved than by waiting for the CCIF flag to set after each program operation. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1177 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Address and program Data 1. Simultaneous Multiple Flash Block Decision Next Flash Block? 2. no Write: FCMD register Program Command 0x20 3. Write: FSTAT register Clear CBEIF 0x80 yes Decrement Global Address by 128K (skip unimplemented Flash) Read: FSTAT register Bit Polling for Buffer Empty Check no CBEIF Set? yes Sequential Programming Decision Next Word? yes no Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 28-28. Example Program Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1178 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.2.4 Sector Erase Command The sector erase operation will erase all addresses in a 1 Kbyte sector of Flash memory using an embedded algorithm. An example flow to execute the sector erase operation is shown in Figure 28-29. The sector erase command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the sector erase command. The Flash address written determines the sector to be erased while global address bits [9:0] and the data written are ignored. Multiple Flash sectors can be simultaneously erased by writing to the same relative address in each Flash block. 2. Write the sector erase command, 0x40, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the sector erase command. If a Flash sector to be erased is in a protected area of the Flash block, the PVIOL flag in the FSTAT register will set and the sector erase command will not launch. Once the sector erase command has successfully launched, the CCIF flag in the FSTAT register will set after the sector erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1179 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check 1. Simultaneous Multiple Flash Block Decision ACCERR/ PVIOL Set? no yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Sector Address and Dummy Data Next Flash Block? yes 2. no Write: FCMD register Sector Erase Command 0x40 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K (skip unimplemented Flash) Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 28-29. Example Sector Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1180 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.2.5 Mass Erase Command The mass erase operation will erase all addresses in a Flash block using an embedded algorithm. An example flow to execute the mass erase operation is shown in Figure 28-30. The mass erase command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the mass erase command. The address and data written will be ignored. Multiple Flash blocks can be simultaneously mass erased by writing to the same relative address in each Flash block. 2. Write the mass erase command, 0x41, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the mass erase command. If a Flash block to be erased contains any protected area, the PVIOL flag in the FSTAT register will set and the mass erase command will not launch. Once the mass erase command has successfully launched, the CCIF flag in the FSTAT register will set after the mass erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1181 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes Access Error and Protection Violation Check 1. Simultaneous Multiple Flash Block Decision ACCERR/ PVIOL Set? no yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 Write: Flash Block Address and Dummy Data Next Flash Block? yes 2. no Write: FCMD register Mass Erase Command 0x41 3. Write: FSTAT register Clear CBEIF 0x80 Decrement Global Address by 128K (skip unimplemented Flash) Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 28-30. Example Mass Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1182 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.2.6 Sector Erase Abort Command The sector erase abort operation will terminate the active sector erase operation so that other sectors in a Flash block are available for read and program operations without waiting for the sector erase operation to complete. An example flow to execute the sector erase abort operation is shown in Figure 28-31. The sector erase abort command write sequence is as follows: 1. Write to any Flash block address to start the command write sequence for the sector erase abort command. The address and data written are ignored. 2. Write the sector erase abort command, 0x47, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the sector erase abort command. If the sector erase abort command is launched resulting in the early termination of an active sector erase operation, the ACCERR flag will set once the operation completes as indicated by the CCIF flag being set. The ACCERR flag sets to inform the user that the Flash sector may not be fully erased and a new sector erase command must be launched before programming any location in that specific sector. If the sector erase abort command is launched but the active sector erase operation completes normally, the ACCERR flag will not set upon completion of the operation as indicated by the CCIF flag being set. Therefore, if the ACCERR flag is not set after the sector erase abort command has completed, a Flash sector being erased when the abort command was launched will be fully erased. The maximum number of cycles required to abort a sector erase operation is equal to four FCLK periods (see Section 28.4.1.1, "Writing the FCLKDIV Register") plus five bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. If sectors in multiple Flash blocks are being simultaneously erased, the sector erase abort operation will be applied to all active Flash blocks without writing to each Flash block in the sector erase abort command write sequence. NOTE Since the ACCERR bit in the FSTAT register may be set at the completion of the sector erase abort operation, a command write sequence is not allowed to be buffered behind a sector erase abort command write sequence. The CBEIF flag will not set after launching the sector erase abort command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a sector erase abort operation active, the ACCERR flag in the FSTAT register will be set. A new command write sequence may be started after clearing the ACCERR flag, if set. NOTE The sector erase abort command should be used sparingly since a sector erase operation that is aborted counts as a complete program/erase cycle. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1183 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) Execute Sector Erase Command Flow Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? Erase Abort Needed? no yes Sector Erase Completed no yes EXIT 1. Write: Dummy Flash Address and Dummy Data 2. Write: FCMD register Sector Erase Abort Cmd 0x47 3. Write: FSTAT register Clear CBEIF 0x80 Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Access Error Check ACCERR Set? yes Write: FSTAT register Clear ACCERR 0x10 no Sector Erase Completed EXIT Sector Erase Aborted EXIT Figure 28-31. Example Sector Erase Abort Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1184 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.4.3 Illegal Flash Operations The ACCERR flag will be set during the command write sequence if any of the following illegal steps are performed, causing the command write sequence to immediately abort: 1. Writing to a Flash address before initializing the FCLKDIV register. 2. Writing a byte or misaligned word to a valid Flash address. 3. Starting a command write sequence while a data compress operation is active. 4. Starting a command write sequence while a sector erase abort operation is active. 5. Writing a Flash address in step 1 of a command write sequence that is not the same relative address as the first one written in the same command write sequence. 6. Writing to any Flash register other than FCMD after writing to a Flash address. 7. Writing a second command to the FCMD register in the same command write sequence. 8. Writing an invalid command to the FCMD register. 9. When security is enabled, writing a command other than mass erase to the FCMD register when the write originates from a non-secure memory location or from the Background Debug Mode. 10. Writing to a Flash address after writing to the FCMD register. 11. Writing to any Flash register other than FSTAT (to clear CBEIF) after writing to the FCMD register. 12. Writing a 0 to the CBEIF flag in the FSTAT register to abort a command write sequence. The ACCERR flag will not be set if any Flash register is read during a valid command write sequence. The ACCERR flag will also be set if any of the following events occur: 1. Launching the sector erase abort command while a sector erase operation is active which results in the early termination of the sector erase operation (see Section 28.4.2.6, "Sector Erase Abort Command"). 2. The MCU enters stop mode and a program or erase operation is in progress. The operation is aborted immediately and any pending command is purged (see Section 28.5.2, "Stop Mode"). If the Flash memory is read during execution of an algorithm (CCIF = 0), the read operation will return invalid data and the ACCERR flag will not be set. If the ACCERR flag is set in the FSTAT register, the user must clear the ACCERR flag before starting another command write sequence (see Section 28.3.2.6, "Flash Status Register (FSTAT)"). The PVIOL flag will be set after the command is written to the FCMD register during a command write sequence if any of the following illegal operations are attempted, causing the command write sequence to immediately abort: 1. Writing the program command if an address written in the command write sequence was in a protected area of the Flash memory 2. Writing the sector erase command if an address written in the command write sequence was in a protected area of the Flash memory 3. Writing the mass erase command to a Flash block while any Flash protection is enabled in the block MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1185 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) If the PVIOL flag is set in the FSTAT register, the user must clear the PVIOL flag before starting another command write sequence (see Section 28.3.2.6, "Flash Status Register (FSTAT)"). 28.5 28.5.1 Operating Modes Wait Mode If a command is active (CCIF = 0) when the MCU enters wait mode, the active command and any buffered command will be completed. The Flash module can recover the MCU from wait mode if the CBEIF and CCIF interrupts are enabled (see Section 28.8, "Interrupts"). 28.5.2 Stop Mode If a command is active (CCIF = 0) when the MCU enters stop mode, the operation will be aborted and, if the operation is program or erase, the Flash array data being programmed or erased may be corrupted and the CCIF and ACCERR flags will be set. If active, the high voltage circuitry to the Flash memory will immediately be switched off when entering stop mode. Upon exit from stop mode, the CBEIF flag is set and any buffered command will not be launched. The ACCERR flag must be cleared before starting a command write sequence (see Section 28.4.1.2, "Command Write Sequence"). NOTE As active commands are immediately aborted when the MCU enters stop mode, it is strongly recommended that the user does not use the STOP instruction during program or erase operations. 28.5.3 Background Debug Mode In background debug mode (BDM), the FPROT register is writable. If the MCU is unsecured, then all Flash commands listed in Table 28-18 can be executed. If the MCU is secured and is in special single chip mode, only mass erase can be executed. 28.6 Flash Module Security The Flash module provides the necessary security information to the MCU. After each reset, the Flash module determines the security state of the MCU as defined in Section 28.3.2.2, "Flash Security Register (FSEC)". The contents of the Flash security byte at 0x7F_FF0F in the Flash Configuration Field must be changed directly by programming 0x7F_FF0F when the MCU is unsecured and the higher address sector is unprotected. If the Flash security byte is left in a secured state, any reset will cause the MCU to initialize to a secure operating mode. MC9S12XDP512 Data Sheet, Rev. 2.21 1186 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) 28.6.1 Unsecuring the MCU using Backdoor Key Access The MCU may be unsecured by using the backdoor key access feature which requires knowledge of the contents of the backdoor keys (four 16-bit words programmed at addresses 0x7F_FF00-0x7F_FF07). If the KEYEN[1:0] bits are in the enabled state (see Section 28.3.2.2, "Flash Security Register (FSEC)") and the KEYACC bit is set, a write to a backdoor key address in the Flash memory triggers a comparison between the written data and the backdoor key data stored in the Flash memory. If all four words of data are written to the correct addresses in the correct order and the data matches the backdoor keys stored in the Flash memory, the MCU will be unsecured. The data must be written to the backdoor keys sequentially starting with 0x7F_FF00-1 and ending with 0x7F_FF06-7. 0x0000 and 0xFFFF are not permitted as backdoor keys. While the KEYACC bit is set, reads of the Flash memory will return invalid data. The user code stored in the Flash memory must have a method of receiving the backdoor keys from an external stimulus. This external stimulus would typically be through one of the on-chip serial ports. If the KEYEN[1:0] bits are in the enabled state (see Section 28.3.2.2, "Flash Security Register (FSEC)"), the MCU can be unsecured by the backdoor key access sequence described below: 1. Set the KEYACC bit in the Flash Configuration Register (FCNFG). 2. Write the correct four 16-bit words to Flash addresses 0xFF00-0xFF07 sequentially starting with 0x7F_FF00. 3. Clear the KEYACC bit. Depending on the user code used to write the backdoor keys, a wait cycle (NOP) may be required before clearing the KEYACC bit. 4. If all four 16-bit words match the backdoor keys stored in Flash addresses 0x7F_FF00-0x7F_FF07, the MCU is unsecured and the SEC[1:0] bits in the FSEC register are forced to the unsecure state of 1:0. The backdoor key access sequence is monitored by an internal security state machine. An illegal operation during the backdoor key access sequence will cause the security state machine to lock, leaving the MCU in the secured state. A reset of the MCU will cause the security state machine to exit the lock state and allow a new backdoor key access sequence to be attempted. The following operations during the backdoor key access sequence will lock the security state machine: 1. If any of the four 16-bit words does not match the backdoor keys programmed in the Flash array. 2. If the four 16-bit words are written in the wrong sequence. 3. If more than four 16-bit words are written. 4. If any of the four 16-bit words written are 0x0000 or 0xFFFF. 5. If the KEYACC bit does not remain set while the four 16-bit words are written. 6. If any two of the four 16-bit words are written on successive MCU clock cycles. After the backdoor keys have been correctly matched, the MCU will be unsecured. Once the MCU is unsecured, the Flash security byte can be programmed to the unsecure state, if desired. In the unsecure state, the user has full control of the contents of the backdoor keys by programming addresses 0x7F_FF00-0x7F_FF07 in the Flash Configuration Field. The security as defined in the Flash security byte (0x7F_FF0F) is not changed by using the backdoor key access sequence to unsecure. The backdoor keys stored in addresses 0x7F_FF00-0x7F_FF07 are MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1187 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) unaffected by the backdoor key access sequence. After the next reset of the MCU, the security state of the Flash module is determined by the Flash security byte (0x7F_FF0F). The backdoor key access sequence has no effect on the program and erase protections defined in the Flash protection register. It is not possible to unsecure the MCU in special single chip mode by using the backdoor key access sequence in background debug mode (BDM). 28.6.2 Unsecuring the MCU in Special Single Chip Mode using BDM The MCU can be unsecured in special single chip mode by erasing the Flash module by the following method: * Reset the MCU into special single chip mode, delay while the erase test is performed by the BDM secure ROM, send BDM commands to disable protection in the Flash module, and execute a mass erase command write sequence to erase the Flash memory. After the CCIF flag sets to indicate that the mass operation has completed, reset the MCU into special single chip mode. The BDM secure ROM will verify that the Flash memory is erased and will assert the UNSEC bit in the BDM status register. This BDM action will cause the MCU to override the Flash security state and the MCU will be unsecured. All BDM commands will be enabled and the Flash security byte may be programmed to the unsecure state by the following method: * Send BDM commands to execute a word program sequence to program the Flash security byte to the unsecured state and reset the MCU. 28.7 28.7.1 Resets Flash Reset Sequence On each reset, the Flash module executes a reset sequence to hold CPU activity while loading the following registers from the Flash memory according to Table 28-1: * FPROT -- Flash Protection Register (see Section 28.3.2.5). * FCTL - Flash Control Register (see Section 28.3.2.8). * FSEC -- Flash Security Register (see Section 28.3.2.2). 28.7.2 Reset While Flash Command Active If a reset occurs while any Flash command is in progress, that command will be immediately aborted. The state of the word being programmed or the sector/block being erased is not guaranteed. 28.8 Interrupts The Flash module can generate an interrupt when all Flash command operations have completed, when the Flash address, data and command buffers are empty. MC9S12XDP512 Data Sheet, Rev. 2.21 1188 Freescale Semiconductor Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) Table 28-19. Flash Interrupt Sources Interrupt Source Interrupt Flag Local Enable Global (CCR) Mask Flash Address, Data and Command Buffers empty CBEIF (FSTAT register) CBEIE (FCNFG register) I Bit All Flash commands completed CCIF (FSTAT register) CCIE (FCNFG register) I Bit NOTE Vector addresses and their relative interrupt priority are determined at the MCU level. 28.8.1 Description of Flash Interrupt Operation The logic used for generating interrupts is shown in Figure 28-32. The Flash module uses the CBEIF and CCIF flags in combination with the CBIE and CCIE enable bits to generate the Flash command interrupt request. CBEIF CBEIE Flash Command Interrupt Request CCIF CCIE Figure 28-32. Flash Interrupt Implementation For a detailed description of the register bits, refer to Section 28.3.2.4, "Flash Configuration Register (FCNFG)" and Section 28.3.2.6, "Flash Status Register (FSTAT)" . MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1189 Chapter 28 256 Kbyte Flash Module (S12XFTX256K2V1) MC9S12XDP512 Data Sheet, Rev. 2.21 1190 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.1 Introduction This document describes the FTX128K1 module that includes a 128 Kbyte Flash (nonvolatile) memory. The Flash memory may be read as either bytes, aligned words or misaligned words. Read access time is one bus cycle for bytes and aligned words, and two bus cycles for misaligned words. The Flash memory is ideal for program and data storage for single-supply applications allowing for field reprogramming without requiring external voltage sources for program or erase. Program and erase functions are controlled by a command driven interface. The Flash module supports both block erase and sector erase. An erased bit reads 1 and a programmed bit reads 0. The high voltage required to program and erase the Flash memory is generated internally. It is not possible to read from a Flash block while it is being erased or programmed. CAUTION A Flash word must be in the erased state before being programmed. Cumulative programming of bits within a Flash word is not allowed. 29.1.1 Glossary Command Write Sequence -- A three-step MCU instruction sequence to execute built-in algorithms (including program and erase) on the Flash memory. Multiple-Input Signature Register (MISR) -- A Multiple-Input Signature Register is an output response analyzer implemented using a linear feedback shift-register (LFSR). A 16-bit MISR is used to compress data and generate a signature that is particular to the data read from a Flash block. 29.1.2 * * * * * * * * Features 128 Kbytes of Flash memory comprised of one 128 Kbyte block divided into 128 sectors of 1024 bytes Automated program and erase algorithm Interrupts on Flash command completion, command buffer empty Fast sector erase and word program operation 2-stage command pipeline for faster multi-word program times Sector erase abort feature for critical interrupt response Flexible protection scheme to prevent accidental program or erase Single power supply for all Flash operations including program and erase MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1191 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) * * Security feature to prevent unauthorized access to the Flash memory Code integrity check using built-in data compression 29.1.3 Modes of Operation Program, erase, erase verify, and data compress operations (please refer to Section 29.4.1, "Flash Command Operations" for details). 29.1.4 Block Diagram A block diagram of the Flash module is shown in Figure 29-1. FTX128K1 Command Interrupt Request Flash Interface Command Pipeline Flash Block cmd2 addr2 data2 cmd1 addr1 data1 Registers 64K * 16 Bits sector 0 sector 1 Protection sector 127 Security Oscillator Clock Clock Divider FCLK Figure 29-1. FTX128K1 Block Diagram 29.2 External Signal Description The Flash module contains no signals that connect off-chip. MC9S12XDP512 Data Sheet, Rev. 2.21 1192 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.3 Memory Map and Register Definition This section describes the memory map and registers for the Flash module. 29.3.1 Module Memory Map The Flash memory map is shown in Figure 29-2. The HCS12X architecture places the Flash memory addresses between global addresses 0x7E_0000 and 0x7F_FFFF. The FPROT register, described in Section 29.3.2.5, "Flash Protection Register (FPROT)", can be set to protect regions in the Flash memory from accidental program or erase. Three separate memory regions, one growing upward from global address 0x7F_8000 in the Flash memory (called the lower region), one growing downward from global address 0x7F_FFFF in the Flash memory (called the higher region), and the remaining addresses in the Flash memory, can be activated for protection. The Flash memory addresses covered by these protectable regions are shown in the Flash memory map. The higher address region is mainly targeted to hold the boot loader code since it covers the vector space. The lower address region can be used for EEPROM emulation in an MCU without an EEPROM module since it can be left unprotected while the remaining addresses are protected from program or erase. Default protection settings as well as security information that allows the MCU to restrict access to the Flash module are stored in the Flash configuration field as described in Table 29-1. Table 29-1. Flash Configuration Field Global Address Size (Bytes) 0x7F_FF00 - 0x7F_FF07 8 Backdoor Comparison Key Refer to Section 29.6.1, "Unsecuring the MCU using Backdoor Key Access" 0x7F_FF08 - 0x7F_FF0C 5 Reserved 0x7F_FF0D 1 Flash Protection byte Refer to Section 29.3.2.5, "Flash Protection Register (FPROT)" 0x7F_FF0E 1 Flash Nonvolatile byte Refer to Section 29.3.2.8, "Flash Control Register (FCTL)" 0x7F_FF0F 1 Flash Security byte Refer to Section 29.3.2.2, "Flash Security Register (FSEC)" Description MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1193 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) MODULE BASE + 0x0000 MODULE BASE + 0x000F Flash Registers 16 bytes FLASH START = 0x7E_0000 Flash Protected/Unprotected Region 96 Kbytes 0x7F_8000 0x7F_8400 0x7F_8800 0x7F_9000 Flash Protected/Unprotected Lower Region 1, 2, 4, 8 Kbytes 0x7F_A000 Flash Protected/Unprotected Region 8 Kbytes (up to 29 Kbytes) 0x7F_C000 0x7F_E000 Flash Protected/Unprotected Higher Region 2, 4, 8, 16 Kbytes 0x7F_F000 0x7F_F800 FLASH END = 0x7F_FFFF Flash Configuration Field 16 bytes (0x7F_FF00 - 0x7F_FF0F) Figure 29-2. Flash Memory Map MC9S12XDP512 Data Sheet, Rev. 2.21 1194 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.3.2 Register Descriptions The Flash module contains a set of 16 control and status registers located between module base + 0x0000 and 0x000F. A summary of the Flash module registers is given in Figure 29-3. Detailed descriptions of each register bit are provided. Register Name FCLKDIV Bit 7 R 6 5 4 3 2 1 Bit 0 PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0 RNV5 RNV4 RNV3 RNV2 0 0 0 0 0 0 0 0 0 0 FDIVLD W FSEC R KEYEN SEC W FTSTMOD R 0 MRDS W FCNFG R CBEIE CCIE KEYACC W FPROT R RNV6 FPOPEN FPHDIS FPHS FPLDIS FPLS W FSTAT R CCIF CBEIF 0 PVIOL BLANK 0 0 NV2 NV1 NV0 ACCERR W FCMD R 0 CMDB W FCTL R 0 NV6 NV5 NV4 NV3 W FADDRHI R FADDRHI W FADDRLO R FADDRLO W FDATAHI R FDATAHI W FDATALO R FDATALO W Figure 29-3. FTX128K1 Register Summary MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1195 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) Register Name RESERVED1 R Bit 7 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W RESERVED2 R W RESERVED3 R W RESERVED4 R W Figure 29-3. FTX128K1 Register Summary (continued) 29.3.2.1 Flash Clock Divider Register (FCLKDIV) The FCLKDIV register is used to control timed events in program and erase algorithms. 7 R 6 5 4 3 2 1 0 PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0 0 0 0 0 0 0 0 FDIVLD W Reset 0 = Unimplemented or Reserved Figure 29-4. Flash Clock Divider Register (FCLKDIV) All bits in the FCLKDIV register are readable, bits 6-0 are write once and bit 7 is not writable. Table 29-2. FCLKDIV Field Descriptions Field Description 7 FDIVLD Clock Divider Loaded. 0 Register has not been written. 1 Register has been written to since the last reset. 6 PRDIV8 Enable Prescalar by 8. 0 The oscillator clock is directly fed into the clock divider. 1 The oscillator clock is divided by 8 before feeding into the clock divider. 5:0 FDIV[5:0] 29.3.2.2 Clock Divider Bits -- The combination of PRDIV8 and FDIV[5:0] must divide the oscillator clock down to a frequency of 150 kHz-200 kHz. The maximum divide ratio is 512. Please refer to Section 29.4.1.1, "Writing the FCLKDIV Register" for more information. Flash Security Register (FSEC) The FSEC register holds all bits associated with the security of the MCU and Flash module. MC9S12XDP512 Data Sheet, Rev. 2.21 1196 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 7 R 6 KEYEN 5 4 3 2 RNV5 RNV4 RNV3 RNV2 F F F F 1 0 SEC W Reset F F F F = Unimplemented or Reserved Figure 29-5. Flash Security Register (FSEC) All bits in the FSEC register are readable but are not writable. The FSEC register is loaded from the Flash Configuration Field at address 0x7F_FF0F during the reset sequence, indicated by F in Figure 29-5. Table 29-3. FSEC Field Descriptions Field Description 7:6 Backdoor Key Security Enable Bits -- The KEYEN[1:0] bits define the enabling of backdoor key access to the KEYEN[1:0] Flash module as shown in Table 29-4. 5:2 RNV[5:2] Reserved Nonvolatile Bits -- The RNV[5:2] bits should remain in the erased state for future enhancements. 1:0 SEC[1:0] Flash Security Bits -- The SEC[1:0] bits define the security state of the MCU as shown in Table 29-5. If the Flash module is unsecured using backdoor key access, the SEC[1:0] bits are forced to 1:0. Table 29-4. Flash KEYEN States KEYEN[1:0] Status of Backdoor Key Access 00 DISABLED 011 DISABLED 10 ENABLED 11 DISABLED 1 Preferred KEYEN state to disable Backdoor Key Access. Table 29-5. Flash Security States SEC[1:0] Status of Security 00 SECURED 1 SECURED 01 10 UNSECURED 11 SECURED 1 Preferred SEC state to set MCU to secured state. The security function in the Flash module is described in Section 29.6, "Flash Module Security". 29.3.2.3 Flash Test Mode Register (FTSTMOD) The FTSTMOD register is used to control Flash test features. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1197 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 7 R 6 5 0 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 MRDS W Reset 0 0 0 = Unimplemented or Reserved Figure 29-6. Flash Test Mode Register (FTSTMOD) MRDS bits are readable and writable while all remaining bits read 0 and are not writable in normal mode. Table 29-6. FTSTMOD Field Descriptions Field Description 6:5 MRDS[1:0] Margin Read Setting -- The MRDS[1:0] bits are used to set the sense-amp margin level for reads of the Flash array as shown in Table 29-7. Table 29-7. FTSTMOD Margin Read Settings MRDS[1:0] Margin Read Setting 00 Normal 01 Program Margin1 10 Erase Margin2 11 Normal 1 Flash array reads will be sensitive to program margin. 2 Flash array reads will be sensitive to erase margin. 29.3.2.4 Flash Configuration Register (FCNFG) The FCNFG register enables the Flash interrupts and gates the security backdoor writes. 7 6 5 CBEIE CCIE KEYACC 0 0 0 R 4 3 2 1 0 Undefined 0 0 0 0 Undefined 0 0 0 0 W Reset = Unimplemented or Reserved Figure 29-7. Flash Configuration Register (FCNFG) CBEIE, CCIE and KEYACC bits are readable and writable while all remaining bits read 0 and are not writable in normal mode. KEYACC is only writable if KEYEN (see Section 29.3.2.2, "Flash Security Register (FSEC)" is set to the enabled state. MC9S12XDP512 Data Sheet, Rev. 2.21 1198 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) Table 29-8. FCNFG Field Descriptions Field Description 7 CBEIE Command Buffer Empty Interrupt Enable -- The CBEIE bit enables an interrupt in case of an empty command buffer in the Flash module. 0 Command buffer empty interrupt disabled. 1 An interrupt will be requested whenever the CBEIF flag (see Section 29.3.2.6, "Flash Status Register (FSTAT)") is set. 6 CCIE Command Complete Interrupt Enable -- The CCIE bit enables an interrupt in case all commands have been completed in the Flash module. 0 Command complete interrupt disabled. 1 An interrupt will be requested whenever the CCIF flag (see Section 29.3.2.6, "Flash Status Register (FSTAT)") is set. 5 KEYACC 29.3.2.5 Enable Security Key Writing 0 Flash writes are interpreted as the start of a command write sequence. 1 Writes to Flash array are interpreted as keys to open the backdoor. Reads of the Flash array return invalid data. Flash Protection Register (FPROT) The FPROT register defines which Flash sectors are protected against program or erase operations. 7 6 R 5 4 3 2 1 0 RNV6 FPOPEN FPHDIS FPHS FPLDIS FPLS W Reset F F F F F F F F = Unimplemented or Reserved Figure 29-8. Flash Protection Register (FPROT) All bits in the FPROT register are readable and writable with restrictions (see Section 29.3.2.5.1, "Flash Protection Restrictions") except for RNV[6] which is only readable. During the reset sequence, the FPROT register is loaded from the Flash Configuration Field at global address 0x7F_FF0D. To change the Flash protection that will be loaded during the reset sequence, the upper sector of the Flash memory must be unprotected, then the Flash Protect/Security byte located as described in Table 29-1 must be reprogrammed. Trying to alter data in any protected area in the Flash memory will result in a protection violation error and the PVIOL flag will be set in the FSTAT register. The mass erase of a Flash block is not possible if any of the Flash sectors contained in the Flash block are protected. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1199 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) Table 29-9. FPROT Field Descriptions Field Description 7 FPOPEN Flash Protection Open -- The FPOPEN bit determines the protection function for program or erase as shown in Table 29-10. 0 The FPHDIS and FPLDIS bits define unprotected address ranges as specified by the corresponding FPHS[1:0] and FPLS[1:0] bits. For an MCU without an EEPROM module, the FPOPEN clear state allows the main part of the Flash block to be protected while a small address range can remain unprotected for EEPROM emulation. 1 The FPHDIS and FPLDIS bits enable protection for the address range specified by the corresponding FPHS[1:0] and FPLS[1:0] bits. 6 RNV6 5 FPHDIS Reserved Nonvolatile Bit -- The RNV[6] bit should remain in the erased state for future enhancements. Flash Protection Higher Address Range Disable -- The FPHDIS bit determines whether there is a protected/unprotected area in a specific region of the Flash memory ending with global address 0x7F_FFFF. 0 Protection/Unprotection enabled. 1 Protection/Unprotection disabled. 4:3 FPHS[1:0] Flash Protection Higher Address Size -- The FPHS[1:0] bits determine the size of the protected/unprotected area as shown inTable 29-11. The FPHS[1:0] bits can only be written to while the FPHDIS bit is set. 2 FPLDIS Flash Protection Lower Address Range Disable -- The FPLDIS bit determines whether there is a protected/unprotected area in a specific region of the Flash memory beginning with global address 0x7F_8000. 0 Protection/Unprotection enabled. 1 Protection/Unprotection disabled. 1:0 FPLS[1:0] Flash Protection Lower Address Size -- The FPLS[1:0] bits determine the size of the protected/unprotected area as shown in Table 29-12. The FPLS[1:0] bits can only be written to while the FPLDIS bit is set. Table 29-10. Flash Protection Function Function1 FPOPEN FPHDIS FPLDIS 1 1 1 No Protection 1 1 0 Protected Low Range 1 0 1 Protected High Range 1 0 0 Protected High and Low Ranges 0 1 1 Full Flash memory Protected 0 1 0 Unprotected Low Range 0 0 1 Unprotected High Range 0 0 0 Unprotected High and Low Ranges 1 For range sizes, refer to Table 29-11 and Table 29-12. Table 29-11. Flash Protection Higher Address Range FPHS[1:0] Global Address Range Protected Size 00 0x7F_F800-0x7F_FFFF 2 Kbytes 01 0x7F_F000-0x7F_FFFF 4 Kbytes 10 0x7F_E000-0x7F_FFFF 8 Kbytes 11 0x7F_C000-0x7F_FFFF 16 Kbytes MC9S12XDP512 Data Sheet, Rev. 2.21 1200 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) Table 29-12. Flash Protection Lower Address Range FPLS[1:0] Global Address Range Protected Size 00 0x7F_8000-0x7F_83FF 1 Kbytes 01 0x7F_8000-0x7F_87FF 2 Kbytes 10 0x7F_8000-0x7F_8FFF 4 Kbytes 11 0x7F_8000-0x7F_9FFF 8 Kbytes All possible Flash protection scenarios are shown in Figure 29-9. Although the protection scheme is loaded from the Flash array at global address 0x7F_FF0D during the reset sequence, it can be changed by the user. This protection scheme can be used by applications requiring re-programming in single chip mode while providing as much protection as possible if re-programming is not required. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1201 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) FPHDIS=1 FPLDIS=1 FPHDIS=1 FPLDIS=0 7 6 0x7E_0000 FPHDIS=0 FPLDIS=1 Scenario FPHDIS=0 FPLDIS=0 5 4 0x7F_8000 FPLS[1:0] FPOPEN=1 FPHS[1:0] 0x7F_FFFF 3 2 Scenario 1 0 0x7E_0000 0x7F_8000 FPLS[1:0] FPOPEN=0 FPHS[1:0] 0x7F_FFFF Unprotected region Protected region with size defined by FPLS Protected region not defined by FPLS, FPHS Protected region with size defined by FPHS Figure 29-9. Flash Protection Scenarios MC9S12XDP512 Data Sheet, Rev. 2.21 1202 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.3.2.5.1 Flash Protection Restrictions The general guideline is that Flash protection can only be added and not removed. Table 29-13 specifies all valid transitions between Flash protection scenarios. Any attempt to write an invalid scenario to the FPROT register will be ignored and the FPROT register will remain unchanged. The contents of the FPROT register reflect the active protection scenario. See the FPHS and FPLS descriptions for additional restrictions. Table 29-13. Flash Protection Scenario Transitions To Protection Scenario1 From Protection Scenario 0 1 2 3 0 X X X X 1 X 2 4 X 4 X X X X X X X X X X 7 X X 7 X 3 6 6 X X 5 5 X X X X X X 1 Allowed transitions marked with X. 29.3.2.6 Flash Status Register (FSTAT) The FSTAT register defines the operational status of the module. 7 6 R 5 4 PVIOL ACCERR 0 0 CCIF CBEIF 3 2 1 0 0 BLANK 0 0 0 0 0 0 W Reset 1 1 = Unimplemented or Reserved Figure 29-10. Flash Status Register (FSTAT -- Normal Mode) 7 6 R 5 4 CCIF CBEIF PVIOL ACCERR 0 0 3 2 0 BLANK 1 0 0 FAIL W Reset 1 1 0 0 0 0 = Unimplemented or Reserved Figure 29-11. Flash Status Register (FSTAT -- Special Mode) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1203 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) CBEIF, PVIOL, and ACCERR are readable and writable, CCIF and BLANK are readable and not writable, remaining bits read 0 and are not writable in normal mode. FAIL is readable and writable in special mode. FAIL must be clear in special mode when starting a command write sequence. Table 29-14. FSTAT Field Descriptions Field Description 7 CBEIF Command Buffer Empty Interrupt Flag -- The CBEIF flag indicates that the address, data and command buffers are empty so that a new command write sequence can be started. Writing a 0 to the CBEIF flag has no effect on CBEIF. Writing a 0 to CBEIF after writing an aligned word to the Flash address space, but before CBEIF is cleared, will abort a command write sequence and cause the ACCERR flag to be set. Writing a 0 to CBEIF outside of a command write sequence will not set the ACCERR flag. The CBEIF flag is cleared by writing a 1 to CBEIF. The CBEIF flag is used together with the CBEIE bit in the FCNFG register to generate an interrupt request (see Figure 29-30). 0 Command buffers are full. 1 Command buffers are ready to accept a new command. 6 CCIF Command Complete Interrupt Flag -- The CCIF flag indicates that there are no more commands pending. The CCIF flag is cleared when CBEIF is cleared and sets automatically upon completion of all active and pending commands. The CCIF flag does not set when an active commands completes and a pending command is fetched from the command buffer. Writing to the CCIF flag has no effect on CCIF. The CCIF flag is used together with the CCIE bit in the FCNFG register to generate an interrupt request (see Figure 29-30). 0 Command in progress. 1 All commands are completed. 5 PVIOL Protection Violation Flag --The PVIOL flag indicates an attempt was made to program or erase an address in a protected area of the Flash memory during a command write sequence. Writing a 0 to the PVIOL flag has no effect on PVIOL. The PVIOL flag is cleared by writing a 1 to PVIOL. While PVIOL is set, it is not possible to launch a command or start a command write sequence. 0 No protection violation detected. 1 Protection violation has occurred. 4 ACCERR Access Error Flag -- The ACCERR flag indicates an illegal access has occurred to the Flash memory caused by either a violation of the command write sequence (see Section 29.4.1.2, "Command Write Sequence"), issuing an illegal Flash command (see Table 29-16), launching the sector erase abort command terminating a sector erase operation early (see Section 29.4.2.6, "Sector Erase Abort Command") or the execution of a CPU STOP instruction while a command is executing (CCIF = 0). Writing a 0 to the ACCERR flag has no effect on ACCERR. The ACCERR flag is cleared by writing a 1 to ACCERR.While ACCERR is set, it is not possible to launch a command or start a command write sequence. If ACCERR is set by an erase verify operation or a data compress operation, any buffered command will not launch. 0 No access error detected. 1 Access error has occurred. 2 BLANK Flag Indicating the Erase Verify Operation Status -- When the CCIF flag is set after completion of an erase verify command, the BLANK flag indicates the result of the erase verify operation. The BLANK flag is cleared by the Flash module when CBEIF is cleared as part of a new valid command write sequence. Writing to the BLANK flag has no effect on BLANK. 0 Flash block verified as not erased. 1 Flash block verified as erased. 1 FAIL Flag Indicating a Failed Flash Operation -- The FAIL flag will set if the erase verify operation fails (Flash block verified as not erased). Writing a 0 to the FAIL flag has no effect on FAIL. The FAIL flag is cleared by writing a 1 to FAIL. 0 Flash operation completed without error. 1 Flash operation failed. MC9S12XDP512 Data Sheet, Rev. 2.21 1204 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.3.2.7 Flash Command Register (FCMD) The FCMD register is the Flash command register. 7 R 6 5 4 3 2 1 0 0 0 0 0 CMDB W Reset 1 1 0 0 0 = Unimplemented or Reserved Figure 29-12. Flash Command Register (FCMD) All CMDB bits are readable and writable during a command write sequence while bit 7 reads 0 and is not writable. Table 29-15. FCMD Field Descriptions Field Description 6:0 CMDB[6:0] Flash Command -- Valid Flash commands are shown in Table 29-16. Writing any command other than those listed in Table 29-16 sets the ACCERR flag in the FSTAT register. Table 29-16. Valid Flash Command List 29.3.2.8 CMDB[6:0] NVM Command 0x05 Erase Verify 0x06 Data Compress 0x20 Word Program 0x40 Sector Erase 0x41 Mass Erase 0x47 Sector Erase Abort Flash Control Register (FCTL) The FCTL register is the Flash control register. R 7 6 5 4 3 2 1 0 0 NV6 NV5 NV4 NV3 NV2 NV1 NV0 0 F F F F F F F W Reset = Unimplemented or Reserved Figure 29-13. Flash Control Register (FCTL) All bits in the FCTL register are readable but are not writable. The FCTL NV bits are loaded from the Flash nonvolatile byte located at global address 0x7F_FF0E during the reset sequence, indicated by F in Figure 29-13. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1205 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) Table 29-17. FCTL Field Descriptions Field Description 6:0 NV[6:0] Nonvolatile Bits -- The NV[6:0] bits are available as nonvolatile bits. Refer to the Device User Guide for proper use of the NV bits. 29.3.2.9 Flash Address Registers (FADDR) The FADDRHI and FADDRLO registers are the Flash address registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 FADDRHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 29-14. Flash Address High Register (FADDRHI) 7 6 5 4 R 3 2 1 0 0 0 0 0 FADDRLO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 29-15. Flash Address Low Register (FADDRLO) All FADDRHI and FADDRLO bits are readable but are not writable. After an array write as part of a command write sequence, the FADDR registers will contain the mapped MCU address written. 29.3.2.10 Flash Data Registers (FDATA) The FDATAHI and FDATALO registers are the Flash data registers. 7 6 5 4 R 3 2 1 0 0 0 0 0 FDATAHI W Reset 0 0 0 0 = Unimplemented or Reserved Figure 29-16. Flash Data High Register (FDATAHI) MC9S12XDP512 Data Sheet, Rev. 2.21 1206 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 7 6 5 4 R 3 2 1 0 0 0 0 0 FDATALO W Reset 0 0 0 0 = Unimplemented or Reserved Figure 29-17. Flash Data Low Register (FDATALO) All FDATAHI and FDATALO bits are readable but are not writable. At the completion of a data compress operation, the resulting 16-bit signature is stored in the FDATA registers. The data compression signature is readable in the FDATA registers until a new command write sequence is started. 29.3.2.11 RESERVED1 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 29-18. RESERVED1 All bits read 0 and are not writable. 29.3.2.12 RESERVED2 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 29-19. RESERVED2 All bits read 0 and are not writable. 29.3.2.13 RESERVED3 This register is reserved for factory testing and is not accessible. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1207 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 29-20. RESERVED3 All bits read 0 and are not writable. 29.3.2.14 RESERVED4 This register is reserved for factory testing and is not accessible. R 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 W Reset = Unimplemented or Reserved Figure 29-21. RESERVED4 All bits read 0 and are not writable. 29.4 29.4.1 Functional Description Flash Command Operations Write operations are used to execute program, erase, erase verify, erase abort, and data compress algorithms described in this section. The program and erase algorithms are controlled by a state machine whose timebase, FCLK, is derived from the oscillator clock via a programmable divider. The command register, as well as the associated address and data registers, operate as a buffer and a register (2-stage FIFO) so that a second command along with the necessary data and address can be stored to the buffer while the first command is still in progress. This pipelined operation allows a time optimization when programming more than one word on a specific row in the Flash block as the high voltage generation can be kept active in between two programming commands. The pipelined operation also allows a simplification of command launching. Buffer empty as well as command completion are signalled by flags in the Flash status register with corresponding interrupts generated, if enabled. The next sections describe: 1. How to write the FCLKDIV register 2. Command write sequences to program, erase, erase verify, erase abort, and data compress operations on the Flash memory 3. Valid Flash commands 4. Effects resulting from illegal Flash command write sequences or aborting Flash operations MC9S12XDP512 Data Sheet, Rev. 2.21 1208 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.1.1 Writing the FCLKDIV Register Prior to issuing any Flash command after a reset, the user is required to write the FCLKDIV register to divide the oscillator clock down to within the 150 kHz to 200 kHz range. Since the program and erase timings are also a function of the bus clock, the FCLKDIV determination must take this information into account. If we define: * FCLK as the clock of the Flash timing control block * Tbus as the period of the bus clock * INT(x) as taking the integer part of x (e.g. INT(4.323) = 4) then FCLKDIV register bits PRDIV8 and FDIV[5:0] are to be set as described in Figure 29-22. For example, if the oscillator clock frequency is 950kHz and the bus clock frequency is 10MHz, FCLKDIV bits FDIV[5:0] should be set to 0x04 (000100) and bit PRDIV8 set to 0. The resulting FCLK frequency is then 190kHz. As a result, the Flash program and erase algorithm timings are increased over the optimum target by: ( 200 - 190 ) 200 x 100 = 5% If the oscillator clock frequency is 16MHz and the bus clock frequency is 40MHz, FCLKDIV bits FDIV[5:0] should be set to 0x0A (001010) and bit PRDIV8 set to 1. The resulting FCLK frequency is then 182kHz. In this case, the Flash program and erase algorithm timings are increased over the optimum target by: ( 200 - 182 ) 200 x 100 = 9% CAUTION Program and erase command execution time will increase proportionally with the period of FCLK. Because of the impact of clock synchronization on the accuracy of the functional timings, programming or erasing the Flash memory cannot be performed if the bus clock runs at less than 1 MHz. Programming or erasing the Flash memory with FCLK < 150 kHz should be avoided. Setting FCLKDIV to a value such that FCLK < 150 kHz can destroy the Flash memory due to overstress. Setting FCLKDIV to a value such that (1/FCLK+Tbus) < 5s can result in incomplete programming or erasure of the Flash memory cells. If the FCLKDIV register is written, the FDIVLD bit is set automatically. If the FDIVLD bit is 0, the FCLKDIV register has not been written since the last reset. If the FCLKDIV register has not been written to, the Flash command loaded during a command write sequence will not execute and the ACCERR flag in the FSTAT register will set. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1209 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) START Tbus < 1s? no ALL COMMANDS IMPOSSIBLE yes PRDIV8=0 (reset) oscillator_clock 12.8MHz? no yes PRDIV8=1 PRDCLK=oscillator_clock/8 PRDCLK[MHz]*(5+Tbus[s]) an integer? yes PRDCLK=oscillator_clock no FDIV[5:0]=INT(PRDCLK[MHz]*(5+Tbus[s])) FDIV[5:0]=PRDCLK[MHz]*(5+Tbus[s])-1 TRY TO DECREASE Tbus FCLK=(PRDCLK)/(1+FDIV[5:0]) 1/FCLK[MHz] + Tbus[s] > 5 AND FCLK > 0.15MHz ? yes END no yes FDIV[5:0] > 4? no ALL COMMANDS IMPOSSIBLE Figure 29-22. Determination Procedure for PRDIV8 and FDIV Bits MC9S12XDP512 Data Sheet, Rev. 2.21 1210 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.1.2 Command Write Sequence The Flash command controller is used to supervise the command write sequence to execute program, erase, erase verify, erase abort, and data compress algorithms. Before starting a command write sequence, the ACCERR and PVIOL flags in the FSTAT register must be clear (see Section 29.3.2.6, "Flash Status Register (FSTAT)") and the CBEIF flag should be tested to determine the state of the address, data and command buffers. If the CBEIF flag is set, indicating the buffers are empty, a new command write sequence can be started. If the CBEIF flag is clear, indicating the buffers are not available, a new command write sequence will overwrite the contents of the address, data and command buffers. A command write sequence consists of three steps which must be strictly adhered to with writes to the Flash module not permitted between the steps. However, Flash register and array reads are allowed during a command write sequence. The basic command write sequence is as follows: 1. Write to a valid address in the Flash memory. 2. Write a valid command to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the command. The address written in step 1 will be stored in the FADDR registers and the data will be stored in the FDATA registers. If the CBEIF flag in the FSTAT register is clear when the first Flash array write occurs, the contents of the address and data buffers will be overwritten and the CBEIF flag will be set. When the CBEIF flag is cleared, the CCIF flag is cleared on the same bus cycle by the Flash command controller indicating that the command was successfully launched. For all command write sequences except data compress and sector erase abort, the CBEIF flag will set four bus cycles after the CCIF flag is cleared indicating that the address, data, and command buffers are ready for a new command write sequence to begin. For data compress and sector erase abort operations, the CBEIF flag will remain clear until the operation completes. Except for the sector erase abort command, a buffered command will wait for the active operation to be completed before being launched. The sector erase abort command is launched when the CBEIF flag is cleared as part of a sector erase abort command write sequence. Once a command is launched, the completion of the command operation is indicated by the setting of the CCIF flag in the FSTAT register. The CCIF flag will set upon completion of all active and buffered commands. 29.4.2 Flash Commands Table 29-18 summarizes the valid Flash commands along with the effects of the commands on the Flash block. Table 29-18. Flash Command Description FCMDB NVM Command 0x05 Erase Verify 0x06 Data Compress 0x20 Program Function on Flash Memory Verify all memory bytes in the Flash block are erased. If the Flash block is erased, the BLANK flag in the FSTAT register will set upon command completion. Compress data from a selected portion of the Flash block. The resulting signature is stored in the FDATA register. Program a word (two bytes) in the Flash block. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1211 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) Table 29-18. Flash Command Description FCMDB NVM Command Function on Flash Memory 0x40 Sector Erase Erase all memory bytes in a sector of the Flash block. 0x41 Mass Erase Erase all memory bytes in the Flash block. A mass erase of the full Flash block is only possible when FPLDIS, FPHDIS and FPOPEN bits in the FPROT register are set prior to launching the command. 0x47 Sector Erase Abort Abort the sector erase operation. The sector erase operation will terminate according to a set procedure. The Flash sector should not be considered erased if the ACCERR flag is set upon command completion. CAUTION A Flash word must be in the erased state before being programmed. Cumulative programming of bits within a Flash word is not allowed. MC9S12XDP512 Data Sheet, Rev. 2.21 1212 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.2.1 Erase Verify Command The erase verify operation will verify that a Flash block is erased. An example flow to execute the erase verify operation is shown in Figure 29-23. The erase verify command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the erase verify command. The address and data written will be ignored. 2. Write the erase verify command, 0x05, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the erase verify command. After launching the erase verify command, the CCIF flag in the FSTAT register will set after the operation has completed unless a new command write sequence has been buffered. The number of bus cycles required to execute the erase verify operation is equal to the number of addresses in a Flash block plus 14 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Upon completion of the erase verify operation, the BLANK flag in the FSTAT register will be set if all addresses in the selected Flash block are verified to be erased. If any address in a selected Flash block is not erased, the erase verify operation will terminate and the BLANK flag in the FSTAT register will remain clear. The MRDS bits in the FTSTMOD register will determine the sense-amp margin setting during the erase verify operation. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1213 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes 1. Write: Flash Block Address and Dummy Data 2. Write: FCMD register Erase Verify Command 0x05 3. Write: FSTAT register Clear CBEIF 0x80 Write: FSTAT register Clear ACCERR/PVIOL 0x30 Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Erase Verify Status BLANK Set? no yes EXIT Flash Block Erased EXIT Flash Block Not Erased Figure 29-23. Example Erase Verify Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1214 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.2.2 Data Compress Command The data compress operation will check Flash code integrity by compressing data from a selected portion of the Flash memory into a signature analyzer. An example flow to execute the data compress operation is shown in Figure 29-24. The data compress command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the data compress command. The address written determines the starting address for the data compress operation and the data written determines the number of consecutive words to compress. If the data value written is 0x0000, 64K addresses or 128 Kbytes will be compressed. 2. Write the data compress command, 0x06, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the data compress command. After launching the data compress command, the CCIF flag in the FSTAT register will set after the data compress operation has completed. The number of bus cycles required to execute the data compress operation is equal to two times the number of consecutive words to compress plus 18 bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. Once the CCIF flag is set, the signature generated by the data compress operation is available in the FDATA registers. The signature in the FDATA registers can be compared to the expected signature to determine the integrity of the selected data stored in the selected Flash memory. If the last address of a Flash block is reached during the data compress operation, data compression will continue with the starting address of the Flash block. The MRDS bits in the FTSTMOD register will determine the sense-amp margin setting during the data compress operation. NOTE Since the FDATA registers (or data buffer) are written to as part of the data compress operation, a command write sequence is not allowed to be buffered behind a data compress command write sequence. The CBEIF flag will not set after launching the data compress command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a data compress operation active, the ACCERR flag in the FSTAT register will be set. A new command write sequence should only be started after reading the signature stored in the FDATA registers. In order to take corrective action, it is recommended that the data compress command be executed on a Flash sector or subset of a Flash sector. If the data compress operation on a Flash sector returns an invalid signature, the Flash sector should be erased using the sector erase command and then reprogrammed using the program command. The data compress command can be used to verify that a sector or sequential set of sectors are erased. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1215 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes Write: FSTAT register Clear ACCERR/PVIOL 0x30 1. Write: Flash Address to start compression and number of word addresses to compress 2. Write: FCMD register Data Compress Command 0x06 3. Write: FSTAT register Clear CBEIF 0x80 Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Read: FDATA registers Data Compress Signature Signature Valid? no Erase and Reprogram Flash Sector(s) Compressed yes EXIT Figure 29-24. Example Data Compress Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 1216 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.2.2.1 Data Compress Operation The Flash module contains a 16-bit multiple-input signature register (MISR) to generate a 16-bit signature based on selected Flash array data. The final 16-bit signature, found in the FDATA registers after the data compress operation has completed, is based on the following logic equation which is executed on every data compression cycle during the operation: MISR[15:0] = {MISR[14:0], ^MISR[15,4,2,1]} ^ DATA[15:0] Eqn. 29-1 where MISR is the content of the internal signature register and DATA is the data to be compressed as shown in Figure 29-25. DATA[0] + DATA[1] DQ DATA[2] + M0 > + DQ M1 > DATA[3] + DQ M2 > + DATA[4] DQ M3 > + + DATA[5] + DQ M4 > DATA[15] DQ M5 > ... + DQ M15 > + + = Exclusive-OR MISR[15:0] = Q[15:0] Figure 29-25. 16-Bit MISR Diagram During the data compress operation, the following steps are executed: 1. MISR is reset to 0xFFFF. 2. Initialized DATA equal to 0xFFFF is compressed into the MISR which results in the MISR containing 0x0001. 3. DATA equal to the selected Flash array data range is read and compressed into the MISR with addresses incrementing. 4. DATA equal to the selected Flash array data range is read and compressed into the MISR with addresses decrementing. 5. DATA equal to the contents of the MISR is compressed into the same MISR. 6. The contents of the MISR are written to the FDATA registers. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1217 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.2.3 Program Command The program operation will program a previously erased word in the Flash memory using an embedded algorithm. An example flow to execute the program operation is shown in Figure 29-26. The program command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the program command. The data written will be programmed to the address written. 2. Write the program command, 0x20, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the program command. If a word to be programmed is in a protected area of the Flash block, the PVIOL flag in the FSTAT register will set and the program command will not launch. Once the program command has successfully launched, the CCIF flag in the FSTAT register will set after the program operation has completed unless a new command write sequence has been buffered. By executing a new program command write sequence on sequential words after the CBEIF flag in the FSTAT register has been set, up to 55% faster programming time per word can be effectively achieved than by waiting for the CCIF flag to set after each program operation. MC9S12XDP512 Data Sheet, Rev. 2.21 1218 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes 1. Write: Flash Address and program Data 2. Write: FCMD register Program Command 0x20 3. Write: FSTAT register Clear CBEIF 0x80 Write: FSTAT register Clear ACCERR/PVIOL 0x30 Read: FSTAT register Bit Polling for Buffer Empty Check CBEIF Set? no yes Sequential Programming Decision Next Word? yes no Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 29-26. Example Program Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1219 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.2.4 Sector Erase Command The sector erase operation will erase all addresses in a 1 Kbyte sector of Flash memory using an embedded algorithm. An example flow to execute the sector erase operation is shown in Figure 29-27. The sector erase command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the sector erase command. The Flash address written determines the sector to be erased while global address bits [9:0] and the data written are ignored. 2. Write the sector erase command, 0x40, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the sector erase command. If a Flash sector to be erased is in a protected area of the Flash block, the PVIOL flag in the FSTAT register will set and the sector erase command will not launch. Once the sector erase command has successfully launched, the CCIF flag in the FSTAT register will set after the sector erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1220 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes 1. Write: Flash Sector Address and Dummy Data 2. Write: FCMD register Sector Erase Command 0x40 3. Write: FSTAT register Clear CBEIF 0x80 Write: FSTAT register Clear ACCERR/PVIOL 0x30 Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 29-27. Example Sector Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1221 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.2.5 Mass Erase Command The mass erase operation will erase all addresses in a Flash block using an embedded algorithm. An example flow to execute the mass erase operation is shown in Figure 29-28. The mass erase command write sequence is as follows: 1. Write to a Flash block address to start the command write sequence for the mass erase command. The address and data written will be ignored. 2. Write the mass erase command, 0x41, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the mass erase command. If a Flash block to be erased contains any protected area, the PVIOL flag in the FSTAT register will set and the mass erase command will not launch. Once the mass erase command has successfully launched, the CCIF flag in the FSTAT register will set after the mass erase operation has completed unless a new command write sequence has been buffered. MC9S12XDP512 Data Sheet, Rev. 2.21 1222 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) START Read: FCLKDIV register Clock Register Written Check FDIVLD Set? yes NOTE: FCLKDIV needs to be set once after each reset. no Write: FCLKDIV register Read: FSTAT register Address, Data, Command Buffer Empty Check CBEIF Set? no yes ACCERR/ PVIOL Set? no Access Error and Protection Violation Check yes 1. Write: Flash Block Address and Dummy Data 2. Write: FCMD register Mass Erase Command 0x41 3. Write: FSTAT register Clear CBEIF 0x80 Write: FSTAT register Clear ACCERR/PVIOL 0x30 Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes EXIT Figure 29-28. Example Mass Erase Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1223 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.2.6 Sector Erase Abort Command The sector erase abort operation will terminate the active sector erase operation so that other sectors in a Flash block are available for read and program operations without waiting for the sector erase operation to complete. An example flow to execute the sector erase abort operation is shown in Figure 29-29. The sector erase abort command write sequence is as follows: 1. Write to any Flash block address to start the command write sequence for the sector erase abort command. The address and data written are ignored. 2. Write the sector erase abort command, 0x47, to the FCMD register. 3. Clear the CBEIF flag in the FSTAT register by writing a 1 to CBEIF to launch the sector erase abort command. If the sector erase abort command is launched resulting in the early termination of an active sector erase operation, the ACCERR flag will set once the operation completes as indicated by the CCIF flag being set. The ACCERR flag sets to inform the user that the Flash sector may not be fully erased and a new sector erase command must be launched before programming any location in that specific sector. If the sector erase abort command is launched but the active sector erase operation completes normally, the ACCERR flag will not set upon completion of the operation as indicated by the CCIF flag being set. Therefore, if the ACCERR flag is not set after the sector erase abort command has completed, a Flash sector being erased when the abort command was launched will be fully erased. The maximum number of cycles required to abort a sector erase operation is equal to four FCLK periods (see Section 29.4.1.1, "Writing the FCLKDIV Register") plus five bus cycles as measured from the time the CBEIF flag is cleared until the CCIF flag is set. NOTE Since the ACCERR bit in the FSTAT register may be set at the completion of the sector erase abort operation, a command write sequence is not allowed to be buffered behind a sector erase abort command write sequence. The CBEIF flag will not set after launching the sector erase abort command to indicate that a command should not be buffered behind it. If an attempt is made to start a new command write sequence with a sector erase abort operation active, the ACCERR flag in the FSTAT register will be set. A new command write sequence may be started after clearing the ACCERR flag, if set. NOTE The sector erase abort command should be used sparingly since a sector erase operation that is aborted counts as a complete program/erase cycle. MC9S12XDP512 Data Sheet, Rev. 2.21 1224 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) Execute Sector Erase Command Flow Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? Erase Abort Needed? no yes Sector Erase Completed no yes EXIT 1. Write: Dummy Flash Address and Dummy Data 2. Write: FCMD register Sector Erase Abort Cmd 0x47 3. Write: FSTAT register Clear CBEIF 0x80 Read: FSTAT register Bit Polling for Command Completion Check CCIF Set? no yes Access Error Check ACCERR Set? yes Write: FSTAT register Clear ACCERR 0x10 no Sector Erase Completed EXIT Sector Erase Aborted EXIT Figure 29-29. Example Sector Erase Abort Command Flow MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1225 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.4.3 Illegal Flash Operations The ACCERR flag will be set during the command write sequence if any of the following illegal steps are performed, causing the command write sequence to immediately abort: 1. Writing to a Flash address before initializing the FCLKDIV register. 2. Writing a byte or misaligned word to a valid Flash address. 3. Starting a command write sequence while a data compress operation is active. 4. Starting a command write sequence while a sector erase abort operation is active. 5. Writing to any Flash register other than FCMD after writing to a Flash address. 6. Writing a second command to the FCMD register in the same command write sequence. 7. Writing an invalid command to the FCMD register. 8. When security is enabled, writing a command other than mass erase to the FCMD register when the write originates from a non-secure memory location or from the Background Debug Mode. 9. Writing to a Flash address after writing to the FCMD register. 10. Writing to any Flash register other than FSTAT (to clear CBEIF) after writing to the FCMD register. 11. Writing a 0 to the CBEIF flag in the FSTAT register to abort a command write sequence. The ACCERR flag will not be set if any Flash register is read during a valid command write sequence. The ACCERR flag will also be set if any of the following events occur: 1. Launching the sector erase abort command while a sector erase operation is active which results in the early termination of the sector erase operation (see Section 29.4.2.6, "Sector Erase Abort Command"). 2. The MCU enters stop mode and a program or erase operation is in progress. The operation is aborted immediately and any pending command is purged (see Section 29.5.2, "Stop Mode"). If the Flash memory is read during execution of an algorithm (CCIF = 0), the read operation will return invalid data and the ACCERR flag will not be set. If the ACCERR flag is set in the FSTAT register, the user must clear the ACCERR flag before starting another command write sequence (see Section 29.3.2.6, "Flash Status Register (FSTAT)"). The PVIOL flag will be set after the command is written to the FCMD register during a command write sequence if any of the following illegal operations are attempted, causing the command write sequence to immediately abort: 1. Writing the program command if an address written in the command write sequence was in a protected area of the Flash memory 2. Writing the sector erase command if an address written in the command write sequence was in a protected area of the Flash memory 3. Writing the mass erase command to a Flash block while any Flash protection is enabled in the block If the PVIOL flag is set in the FSTAT register, the user must clear the PVIOL flag before starting another command write sequence (see Section 29.3.2.6, "Flash Status Register (FSTAT)"). MC9S12XDP512 Data Sheet, Rev. 2.21 1226 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.5 29.5.1 Operating Modes Wait Mode If a command is active (CCIF = 0) when the MCU enters wait mode, the active command and any buffered command will be completed. The Flash module can recover the MCU from wait mode if the CBEIF and CCIF interrupts are enabled (see Section 29.8, "Interrupts"). 29.5.2 Stop Mode If a command is active (CCIF = 0) when the MCU enters stop mode, the operation will be aborted and, if the operation is program or erase, the Flash array data being programmed or erased may be corrupted and the CCIF and ACCERR flags will be set. If active, the high voltage circuitry to the Flash memory will immediately be switched off when entering stop mode. Upon exit from stop mode, the CBEIF flag is set and any buffered command will not be launched. The ACCERR flag must be cleared before starting a command write sequence (see Section 29.4.1.2, "Command Write Sequence"). NOTE As active commands are immediately aborted when the MCU enters stop mode, it is strongly recommended that the user does not use the STOP instruction during program or erase operations. 29.5.3 Background Debug Mode In background debug mode (BDM), the FPROT register is writable. If the MCU is unsecured, then all Flash commands listed in Table 29-18 can be executed. If the MCU is secured and is in special single chip mode, only mass erase can be executed. 29.6 Flash Module Security The Flash module provides the necessary security information to the MCU. After each reset, the Flash module determines the security state of the MCU as defined in Section 29.3.2.2, "Flash Security Register (FSEC)". The contents of the Flash security byte at 0x7F_FF0F in the Flash Configuration Field must be changed directly by programming 0x7F_FF0F when the MCU is unsecured and the higher address sector is unprotected. If the Flash security byte is left in a secured state, any reset will cause the MCU to initialize to a secure operating mode. 29.6.1 Unsecuring the MCU using Backdoor Key Access The MCU may be unsecured by using the backdoor key access feature which requires knowledge of the contents of the backdoor keys (four 16-bit words programmed at addresses 0x7F_FF00-0x7F_FF07). If the KEYEN[1:0] bits are in the enabled state (see Section 29.3.2.2, "Flash Security Register (FSEC)") and the KEYACC bit is set, a write to a backdoor key address in the Flash memory triggers a comparison MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1227 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) between the written data and the backdoor key data stored in the Flash memory. If all four words of data are written to the correct addresses in the correct order and the data matches the backdoor keys stored in the Flash memory, the MCU will be unsecured. The data must be written to the backdoor keys sequentially starting with 0x7F_FF00-1 and ending with 0x7F_FF06-7. 0x0000 and 0xFFFF are not permitted as backdoor keys. While the KEYACC bit is set, reads of the Flash memory will return invalid data. The user code stored in the Flash memory must have a method of receiving the backdoor keys from an external stimulus. This external stimulus would typically be through one of the on-chip serial ports. If the KEYEN[1:0] bits are in the enabled state (see Section 29.3.2.2, "Flash Security Register (FSEC)"), the MCU can be unsecured by the backdoor key access sequence described below: 1. Set the KEYACC bit in the Flash Configuration Register (FCNFG). 2. Write the correct four 16-bit words to Flash addresses 0xFF00-0xFF07 sequentially starting with 0x7F_FF00. 3. Clear the KEYACC bit. Depending on the user code used to write the backdoor keys, a wait cycle (NOP) may be required before clearing the KEYACC bit. 4. If all four 16-bit words match the backdoor keys stored in Flash addresses 0x7F_FF00-0x7F_FF07, the MCU is unsecured and the SEC[1:0] bits in the FSEC register are forced to the unsecure state of 1:0. The backdoor key access sequence is monitored by an internal security state machine. An illegal operation during the backdoor key access sequence will cause the security state machine to lock, leaving the MCU in the secured state. A reset of the MCU will cause the security state machine to exit the lock state and allow a new backdoor key access sequence to be attempted. The following operations during the backdoor key access sequence will lock the security state machine: 1. If any of the four 16-bit words does not match the backdoor keys programmed in the Flash array. 2. If the four 16-bit words are written in the wrong sequence. 3. If more than four 16-bit words are written. 4. If any of the four 16-bit words written are 0x0000 or 0xFFFF. 5. If the KEYACC bit does not remain set while the four 16-bit words are written. 6. If any two of the four 16-bit words are written on successive MCU clock cycles. After the backdoor keys have been correctly matched, the MCU will be unsecured. Once the MCU is unsecured, the Flash security byte can be programmed to the unsecure state, if desired. In the unsecure state, the user has full control of the contents of the backdoor keys by programming addresses 0x7F_FF00-0x7F_FF07 in the Flash Configuration Field. The security as defined in the Flash security byte (0x7F_FF0F) is not changed by using the backdoor key access sequence to unsecure. The backdoor keys stored in addresses 0x7F_FF00-0x7F_FF07 are unaffected by the backdoor key access sequence. After the next reset of the MCU, the security state of the Flash module is determined by the Flash security byte (0x7F_FF0F). The backdoor key access sequence has no effect on the program and erase protections defined in the Flash protection register. It is not possible to unsecure the MCU in special single chip mode by using the backdoor key access sequence in background debug mode (BDM). MC9S12XDP512 Data Sheet, Rev. 2.21 1228 Freescale Semiconductor Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) 29.6.2 Unsecuring the MCU in Special Single Chip Mode using BDM The MCU can be unsecured in special single chip mode by erasing the Flash module by the following method: * Reset the MCU into special single chip mode, delay while the erase test is performed by the BDM secure ROM, send BDM commands to disable protection in the Flash module, and execute a mass erase command write sequence to erase the Flash memory. After the CCIF flag sets to indicate that the mass operation has completed, reset the MCU into special single chip mode. The BDM secure ROM will verify that the Flash memory is erased and will assert the UNSEC bit in the BDM status register. This BDM action will cause the MCU to override the Flash security state and the MCU will be unsecured. All BDM commands will be enabled and the Flash security byte may be programmed to the unsecure state by the following method: * Send BDM commands to execute a word program sequence to program the Flash security byte to the unsecured state and reset the MCU. 29.7 29.7.1 Resets Flash Reset Sequence On each reset, the Flash module executes a reset sequence to hold CPU activity while loading the following registers from the Flash memory according to Table 29-1: * FPROT -- Flash Protection Register (see Section 29.3.2.5). * FCTL - Flash Control Register (see Section 29.3.2.8). * FSEC -- Flash Security Register (see Section 29.3.2.2). 29.7.2 Reset While Flash Command Active If a reset occurs while any Flash command is in progress, that command will be immediately aborted. The state of the word being programmed or the sector/block being erased is not guaranteed. 29.8 Interrupts The Flash module can generate an interrupt when all Flash command operations have completed, when the Flash address, data and command buffers are empty. Table 29-19. Flash Interrupt Sources Interrupt Source Interrupt Flag Local Enable Global (CCR) Mask Flash Address, Data and Command Buffers empty CBEIF (FSTAT register) CBEIE (FCNFG register) I Bit All Flash commands completed CCIF (FSTAT register) CCIE (FCNFG register) I Bit MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1229 Chapter 29 128 Kbyte Flash Module (S12XFTX128K1V1) NOTE Vector addresses and their relative interrupt priority are determined at the MCU level. 29.8.1 Description of Flash Interrupt Operation The logic used for generating interrupts is shown in Figure 29-30. The Flash module uses the CBEIF and CCIF flags in combination with the CBIE and CCIE enable bits to generate the Flash command interrupt request. CBEIF CBEIE Flash Command Interrupt Request CCIF CCIE Figure 29-30. Flash Interrupt Implementation For a detailed description of the register bits, refer to Section 29.3.2.4, "Flash Configuration Register (FCNFG)" and Section 29.3.2.6, "Flash Status Register (FSTAT)" . MC9S12XDP512 Data Sheet, Rev. 2.21 1230 Freescale Semiconductor Chapter 30 Security (S12X9SECV2) 30.1 Introduction This specification describes the function of the security mechanism in the S12X chip family (S12X9SECV2). 30.1.1 Features The user must be reminded that part of the security must lie with the application code. An extreme example would be application code that dumps the contents of the internal memory. This would defeat the purpose of security. At the same time, the user may also wish to put a backdoor in the application program. An example of this is the user downloads a security key through the SCI, which allows access to a programming routine that updates parameters stored in another section of the Flash memory. The security features of the S12X chip family (in secure mode) are: * Protect the contents of non-volatile memories (Flash, EEPROM) * Execution of NVM commands is restricted * Disable access to internal memory via background debug module (BDM) * Disable access to internal Flash/EEPROM in expanded modes * Disable debugging features for CPU and XGATE Table 30-1 gives an overview over availability of security relevant features in unsecure and secure modes. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1231 Chapter 30 Security (S12X9SECV2) Table 30-1. Features Availability in Unsecure and Secure Modes Unsecure Mode Secure Mode NS SS NX ES EX ST NS SS NX ES EX ST Flash Array Access 1 1 1 1 -- -- -- -- EEPROM Array Access -- -- -- -- NVM Commands 2 2 2 2 2 2 2 2 2 2 BDM -- 3 -- -- -- -- DBG Module Trace -- -- -- -- -- -- XGATE Debugging -- -- -- -- -- -- External Bus Interface -- -- -- -- Internal status visible multiplexed on external bus -- -- -- -- -- -- -- -- Internal accesses visible on external bus -- -- -- -- -- -- -- -- -- -- 1 Availability of Flash arrays in the memory map depends on ROMCTL/EROMCTL pins and/or the state of the ROMON/EROMON bits in the MMCCTL1 register. Please refer to the S12X_MMC block guide for detailed information. 2 Restricted NVM command set only. Please refer to the FTX/EETX block guides for detailed information. 3 BDM hardware commands restricted to peripheral registers only. 30.1.2 Modes of Operation 30.1.3 Securing the Microcontroller Once the user has programmed the Flash and EEPROM, the chip can be secured by programming the security bits located in the options/security byte in the Flash memory array. These non-volatile bits will keep the device secured through reset and power-down. The options/security byte is located at address 0xFF0F (= global address 0x7F_FF0F) in the Flash memory array. This byte can be erased and programmed like any other Flash location. Two bits of this byte are used for security (SEC[1:0]). On devices which have a memory page window, the Flash options/security byte is also available at address 0xBF0F by selecting page 0x3F with the PPAGE register. The contents of this byte are copied into the Flash security register (FSEC) during a reset sequence. 0xFF0F 7 6 5 4 3 2 1 0 KEYEN1 KEYEN0 NV5 NV4 NV3 NV2 SEC1 SEC0 Figure 30-1. Flash Options/Security Byte MC9S12XDP512 Data Sheet, Rev. 2.21 1232 Freescale Semiconductor Chapter 30 Security (S12X9SECV2) The meaning of the bits KEYEN[1:0] is shown in Table 30-2. Please refer to Section 30.1.5.1, "Unsecuring the MCU Using the Backdoor Key Access" for more information. Table 30-2. Backdoor Key Access Enable Bits KEYEN[1:0] Backdoor Key Access Enabled 00 0 (disabled) 01 0 (disabled) 10 1 (enabled) 11 0 (disabled) The meaning of the security bits SEC[1:0] is shown in Table 30-3. For security reasons, the state of device security is controlled by two bits. To put the device in unsecured mode, these bits must be programmed to SEC[1:0] = `10'. All other combinations put the device in a secured mode. The recommended value to put the device in secured state is the inverse of the unsecured state, i.e. SEC[1:0] = `01'. Table 30-3. Security Bits SEC[1:0] Security State 00 1 (secured) 01 1 (secured) 10 0 (unsecured) 11 1 (secured) NOTE Please refer to the Flash block guide (FTX) for actual security configuration (in section "Flash Module Security"). 30.1.4 Operation of the Secured Microcontroller By securing the device, unauthorized access to the EEPROM and Flash memory contents can be prevented. However, it must be understood that the security of the EEPROM and Flash memory contents also depends on the design of the application program. For example, if the application has the capability of downloading code through a serial port and then executing that code (e.g. an application containing bootloader code), then this capability could potentially be used to read the EEPROM and Flash memory contents even when the microcontroller is in the secure state. In this example, the security of the application could be enhanced by requiring a challenge/response authentication before any code can be downloaded. Secured operation has the following effects on the microcontroller: MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1233 Chapter 30 Security (S12X9SECV2) 30.1.4.1 * * * * Background debug module (BDM) operation is completely disabled. Execution of Flash and EEPROM commands is restricted. Please refer to the NVM block guide (FTX) for details. Tracing code execution using the DBG module is disabled. Debugging XGATE code (breakpoints, single-stepping) is disabled. 30.1.4.2 * * * * * Normal Single Chip Mode (NS) Special Single Chip Mode (SS) BDM firmware commands are disabled. BDM hardware commands are restricted to the register space. Execution of Flash and EEPROM commands is restricted. Please refer to the NVM block guide (FTX) for details. Tracing code execution using the DBG module is disabled. Debugging XGATE code (breakpoints, single-stepping) is disabled. Special single chip mode means BDM is active after reset. The availability of BDM firmware commands depends on the security state of the device. The BDM secure firmware first performs a blank check of both the Flash memory and the EEPROM. If the blank check succeeds, security will be temporarily turned off and the state of the security bits in the appropriate Flash memory location can be changed If the blank check fails, security will remain active, only the BDM hardware commands will be enabled, and the accessible memory space is restricted to the peripheral register area. This will allow the BDM to be used to erase the EEPROM and Flash memory without giving access to their contents. After erasing both Flash memory and EEPROM, another reset into special single chip mode will cause the blank check to succeed and the options/security byte can be programmed to "unsecured" state via BDM. While the BDM is executing the blank check, the BDM interface is completely blocked, which means that all BDM commands are temporarily blocked. 30.1.4.3 * * * * * * Expanded Modes (NX, ES, EX, and ST) BDM operation is completely disabled. Internal Flash memory and EEPROM are disabled. Execution of Flash and EEPROM commands is restricted. Please refer to the NVM block guide (FTX) for details. Tracing code execution using the DBG module is disabled. Debugging XGATE code (breakpoints, single-stepping) is disabled. MC9S12XDP512 Data Sheet, Rev. 2.21 1234 Freescale Semiconductor Chapter 30 Security (S12X9SECV2) 30.1.5 Unsecuring the Microcontroller Unsecuring the microcontroller can be done by three different methods: 1. Backdoor key access 2. Reprogramming the security bits 3. Complete memory erase (special modes) 30.1.5.1 Unsecuring the MCU Using the Backdoor Key Access In normal modes (single chip and expanded), security can be temporarily disabled using the backdoor key access method. This method requires that: * * * The backdoor key at 0xFF00-0xFF07 (= global addresses 0x7F_FF00-0x7F_FF07) has been programmed to a valid value. The KEYEN[1:0] bits within the Flash options/security byte select `enabled'. In single chip mode, the application program programmed into the microcontroller must be designed to have the capability to write to the backdoor key locations. The backdoor key values themselves would not normally be stored within the application data, which means the application program would have to be designed to receive the backdoor key values from an external source (e.g. through a serial port). It is not possible to download the backdoor keys using background debug mode. The backdoor key access method allows debugging of a secured microcontroller without having to erase the Flash. This is particularly useful for failure analysis. NOTE No word of the backdoor key is allowed to have the value 0x0000 or 0xFFFF. 30.1.5.2 Backdoor Key Access Sequence These are the necessary steps for a successful backdoor key access sequence: 1. Set the KEYACC bit in the Flash configuration register FCNFG. 2. Write the first 16-bit word of the backdoor key to 0xFF00 (0x7F_FF00). 3. Write the second 16-bit word of the backdoor key to 0xFF02 (0x7F_FF02). 4. Write the third 16-bit word of the backdoor key to 0xFF04 (0x7F_FF04). 5. Write the fourth 16-bit word of the backdoor key to 0xFF06 (0x7F_FF06). 6. Clear the KEYACC bit in the Flash Configuration register FCNFG. NOTE Flash cannot be read while KEYACC is set. Therefore the code for the backdoor key access sequence must execute from RAM. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1235 Chapter 30 Security (S12X9SECV2) If all four 16-bit words match the Flash contents at 0xFF00-0xFF07 (0x7F_FF00-0x7F_FF07), the microcontroller will be unsecured and the security bits SEC[1:0] in the Flash Security register FSEC will be forced to the unsecured state (`10'). The contents of the Flash options/security byte are not changed by this procedure, and so the microcontroller will revert to the secure state after the next reset unless further action is taken as detailed below. If any of the four 16-bit words does not match the Flash contents at 0xFF00-0xFF07 (0x7F_FF00-0x7F_FF07), the microcontroller will remain secured. 30.1.6 Reprogramming the Security Bits In normal single chip mode (NS), security can also be disabled by erasing and reprogramming the security bits within Flash options/security byte to the unsecured value. Because the erase operation will erase the entire sector from 0xFE00-0xFFFF (0x7F_FE00-0x7F_FFFF), the backdoor key and the interrupt vectors will also be erased; this method is not recommended for normal single chip mode. The application software can only erase and program the Flash options/security byte if the Flash sector containing the Flash options/security byte is not protected (see Flash protection). Thus Flash protection is a useful means of preventing this method. The microcontroller will enter the unsecured state after the next reset following the programming of the security bits to the unsecured value. This method requires that: * The application software previously programmed into the microcontroller has been designed to have the capability to erase and program the Flash options/security byte, or security is first disabled using the backdoor key method, allowing BDM to be used to issue commands to erase and program the Flash options/security byte. * The Flash sector containing the Flash options/security byte is not protected. 30.1.7 Complete Memory Erase (Special Modes) The microcontroller can be unsecured in special modes by erasing the entire EEPROM and Flash memory contents. When a secure microcontroller is reset into special single chip mode (SS), the BDM firmware verifies whether the EEPROM and Flash memory are erased. If any EEPROM or Flash memory address is not erased, only BDM hardware commands are enabled. BDM hardware commands can then be used to write to the EEPROM and Flash registers to mass erase the EEPROM and all Flash memory blocks. When next reset into special single chip mode, the BDM firmware will again verify whether all EEPROM and Flash memory are erased, and this being the case, will enable all BDM commands, allowing the Flash options/security byte to be programmed to the unsecured value. The security bits SEC[1:0] in the Flash security register will indicate the unsecure state following the next reset. MC9S12XDP512 Data Sheet, Rev. 2.21 1236 Freescale Semiconductor Chapter 30 Security (S12X9SECV2) Special single chip erase and unsecure sequence: 1. Reset into special single chip mode. 2. Write an appropriate value to the ECLKDIV register for correct timing. 3. Write 0xFF to the EPROT register to disable protection. 4. Write 0x30 to the ESTAT register to clear the PVIOL and ACCERR bits. 5. Write 0x0000 to the EDATA register (0x011A-0x011B). 6. Write 0x0000 to the EADDR register (0x0118-0x0119). 7. Write 0x41 (mass erase) to the ECMD register. 8. Write 0x80 to the ESTAT register to clear CBEIF. 9. Write an appropriate value to the FCLKDIV register for correct timing. 10. Write 0x00 to the FCNFG register to select Flash block 0. 11. Write 0x10 to the FTSTMOD register (0x0102) to set the WRALL bit, so the following writes affect all Flash blocks. 12. Write 0xFF to the FPROT register to disable protection. 13. Write 0x30 to the FSTAT register to clear the PVIOL and ACCERR bits. 14. Write 0x0000 to the FDATA register (0x010A-0x010B). 15. Write 0x0000 to the FADDR register (0x0108-0x0109). 16. Write 0x41 (mass erase) to the FCMD register. 17. Write 0x80 to the FSTAT register to clear CBEIF. 18. Wait until all CCIF flags are set. 19. Reset back into special single chip mode. 20. Write an appropriate value to the FCLKDIV register for correct timing. 21. Write 0x00 to the FCNFG register to select Flash block 0. 22. Write 0xFF to the FPROT register to disable protection. 23. Write 0xFFBE to Flash address 0xFF0E. 24. Write 0x20 (program) to the FCMD register. 25. Write 0x80 to the FSTAT register to clear CBEIF. 26. Wait until the CCIF flag in FSTAT is are set. 27. Reset into any mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1237 Chapter 30 Security (S12X9SECV2) MC9S12XDP512 Data Sheet, Rev. 2.21 1238 Freescale Semiconductor Appendix A Electrical Characteristics Appendix A Electrical Characteristics A.1 General This supplement contains the most accurate electrical information for the S12XD, S12XB & S12XA families microcontroller available at the time of publication. This introduction is intended to give an overview on several common topics like power supply, current injection etc. A.1.1 Parameter Classification The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate. NOTE This classification is shown in the column labeled "C" in the parameter tables where appropriate. P: C: T: D: A.1.2 Those parameters are guaranteed during production testing on each individual device. Those parameters are achieved by the design characterization by measuring a statistically relevant sample size across process variations. Those parameters are achieved by design characterization on a small sample size from typical devices under typical conditions unless otherwise noted. All values shown in the typical column are within this category. Those parameters are derived mainly from simulations. Power Supply The MC9S12XDP512RMV2 utilizes several pins to supply power to the I/O ports, A/D converter, oscillator, and PLL as well as the digital core. The VDDA, VSSA pair supplies the A/D converter and parts of the internal voltage regulator. The VDDX, VSSX, VDDR, and VSSR pairs supply the I/O pins, VDDR supplies also the internal voltage regulator. VDD1, VSS1, VDD2, and VSS2 are the supply pins for the digital logic, VDDPLL, VSSPLL supply the oscillator and the PLL. VSS1 and VSS2 are internally connected by metal. VDDA, VDDX, VDDR as well as VSSA, VSSX, VSSR are connected by anti-parallel diodes for ESD protection. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1239 Appendix A Electrical Characteristics NOTE In the following context VDD35 is used for either VDDA, VDDR, and VDDX; VSS35 is used for either VSSA, VSSR and VSSX unless otherwise noted. IDD35 denotes the sum of the currents flowing into the VDDA, VDDX and VDDR pins. VDD is used for VDD1, VDD2 and VDDPLL, VSS is used for VSS1, VSS2 and VSSPLL. IDD is used for the sum of the currents flowing into VDD1 and VDD2. A.1.3 Pins There are four groups of functional pins. A.1.3.1 I/O Pins Those I/O pins have a nominal level in the range of 3.15 V to 5.5 V. This class of pins is comprised of all port I/O pins, the analog inputs, BKGD and the RESET pins.The internal structure of all those pins is identical; however, some of the functionality may be disabled. For example, for the analog inputs the output drivers, pull-up and pull-down resistors are disabled permanently. A.1.3.2 Analog Reference This group is made up by the VRH and VRL pins. A.1.3.3 Oscillator The pins XFC, EXTAL, XTAL dedicated to the oscillator have a nominal 2.5 V level. They are supplied by VDDPLL. A.1.3.4 TEST This pin is used for production testing only. A.1.3.5 VREGEN This pin is used to enable the on-chip voltage regulator. A.1.4 Current Injection Power supply must maintain regulation within operating VDD35 or VDD range during instantaneous and operating maximum current conditions. If positive injection current (Vin > VDD35) is greater than IDD35, the injection current may flow out of VDD35 and could result in external power supply going out of regulation. Ensure external VDD35 load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power; e.g., if no system clock is present, or if clock rate is very low which would reduce overall power consumption. MC9S12XDP512 Data Sheet, Rev. 2.21 1240 Freescale Semiconductor Appendix A Electrical Characteristics A.1.5 Absolute Maximum Ratings Absolute maximum ratings are stress ratings only. A functional operation under or outside those maxima is not guaranteed. Stress beyond those limits may affect the reliability or cause permanent damage of the device. This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (e.g., either VSS35 or VDD35). Table A-1. Absolute Maximum Ratings1 Num Rating 1 I/O, regulator and analog supply voltage 2 Digital logic supply voltage2 Symbol Min Max Unit VDD35 -0.3 6.0 V VDD -0.3 3.0 V 2 3 PLL supply voltage VDDPLL -0.3 3.0 V 4 Voltage difference VDDX to VDDR and VDDA VDDX -0.3 0.3 V 5 Voltage difference VSSX to VSSR and VSSA VSSX -0.3 0.3 V 6 Digital I/O input voltage VIN -0.3 6.0 V 7 Analog reference VRH, VRL -0.3 6.0 V 8 XFC, EXTAL, XTAL inputs VILV -0.3 3.0 V 9 TEST input VTEST -0.3 10.0 V 10 Instantaneous maximum current Single pin limit for all digital I/O pins3 I -25 +25 mA 11 Instantaneous maximum current Single pin limit for XFC, EXTAL, XTAL4 IDL -25 +25 mA 12 Instantaneous maximum current Single pin limit for TEST 5 IDT -0.25 0 mA 13 Storage temperature range Tstg -65 155 C D 1 Beyond absolute maximum ratings device might be damaged. The device contains an internal voltage regulator to generate the logic and PLL supply out of the I/O supply. The absolute maximum ratings apply when the device is powered from an external source. 3 All digital I/O pins are internally clamped to V SSX and VDDX, VSSR and VDDR or VSSA and VDDA. 4 Those pins are internally clamped to VSSPLL and VDDPLL. 5 This pin is clamped low to V SSPLL, but not clamped high. This pin must be tied low in applications. 2 A.1.6 ESD Protection and Latch-up Immunity All ESD testing is in conformity with CDF-AEC-Q100 stress test qualification for automotive grade integrated circuits. During the device qualification ESD stresses were performed for the Human Body Model (HBM) and the Charge Device Model. A device will be defined as a failure if after exposure to ESD pulses the device no longer meets the device specification. Complete DC parametric and functional testing is performed per the applicable device MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1241 Appendix A Electrical Characteristics specification at room temperature followed by hot temperature, unless specified otherwise in the device specification. Table A-2. ESD and Latch-up Test Conditions Model Description Human Body Latch-up Symbol Value Unit Series resistance R1 1500 Ohm Storage capacitance C 100 pF Number of pulse per pin Positive Negative -- -- 3 3 Minimum input voltage limit -2.5 V Maximum input voltage limit 7.5 V Table A-3. ESD and Latch-Up Protection Characteristics Num C 1 C 2 3 4 Symbol Min Max Unit Human Body Model (HBM) VHBM 2000 -- V C Charge Device Model (CDM) VCDM 500 -- V C Latch-up current at TA = 125C Positive Negative ILAT +100 -100 -- -- Latch-up current at TA = 27C Positive Negative ILAT +200 -200 -- -- C Rating mA mA MC9S12XDP512 Data Sheet, Rev. 2.21 1242 Freescale Semiconductor Appendix A Electrical Characteristics A.1.7 Operating Conditions This section describes the operating conditions of the device. Unless otherwise noted those conditions apply to all the following data. NOTE Please refer to the temperature rating of the device (C, V, M) with regards to the ambient temperature TA and the junction temperature TJ. For power dissipation calculations refer to Section A.1.8, "Power Dissipation and Thermal Characteristics". Table A-4. Operating Conditions Rating Symbol Min Typ Max Unit VDD35 3.15 5 5.5 V VDD 2.35 2.5 2.75 V PLL supply voltage VDDPLL 2.35 2.5 2.75 V Voltage difference VDDX to VDDR and VDDA VDDX -0.1 0 0.1 V Voltage difference VSSX to VSSR and VSSA VSSX -0.1 0 0.1 V Oscillator fosc 0.5 -- 16 MHz Bus frequency fbus 0.5 -- 40 MHz C parts Operating junction temperature range Operating ambient temperature range2 TJ TA -40 -40 -- 27 100 85 V parts Operating junction temperature range Operating ambient temperature range2 TJ TA -40 -40 -- 27 120 105 M parts Operating junction temperature range Operating ambient temperature range2 TJ TA -40 -40 -- 27 140 125 I/O, regulator and analog supply voltage Digital logic supply voltage1 2 C C C 1 The device contains an internal voltage regulator to generate the logic and PLL supply out of the I/O supply. The absolute maximum ratings apply when this regulator is disabled and the device is powered from an external source. 2 Please refer to Section A.1.8, "Power Dissipation and Thermal Characteristics" for more details about the relation between ambient temperature TA and device junction temperature TJ. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1243 Appendix A Electrical Characteristics A.1.8 Power Dissipation and Thermal Characteristics Power dissipation and thermal characteristics are closely related. The user must assure that the maximum operating junction temperature is not exceeded. The average chip-junction temperature (TJ) in C can be obtained from: T T T J = Junction Temperature, [C ] A = Ambient Temperature, [C ] P D J = T + (P * ) A D JA = Total Chip Power Dissipation, [W] JA = Package Thermal Resistance, [C/W] The total power dissipation can be calculated from: P P INT D = P INT +P IO = Chip Internal Power Dissipation, [W] Two cases with internal voltage regulator enabled and disabled must be considered: 1. Internal voltage regulator disabled P INT = I DD V DD P IO +I = DDPLL V DDPLL +I DDA V DDA i RDSON IIOi2 PIO is the sum of all output currents on I/O ports associated with VDDX and VDDR. For RDSON is valid: R V OL = ------------ ;for outputs driven low DSON I OL respectively R V -V DD5 OH = ------------------------------------ ;for outputs driven high DSON I OH 2. Internal voltage regulator enabled P INT = I DDR V DDR +I DDA V DDA IDDR is the current shown in Table A-10. and not the overall current flowing into VDDR, which additionally contains the current flowing into the external loads with output high. P IO = i RDSON IIOi2 PIO is the sum of all output currents on I/O ports associated with VDDX and VDDR. MC9S12XDP512 Data Sheet, Rev. 2.21 1244 Freescale Semiconductor Appendix A Electrical Characteristics Table A-5. Thermal Package Characteristics1 Num C Rating Symbol Min Typ Max Unit LQFP144 1 T Thermal resistance LQFP144, single sided PCB2 JA -- -- 41 C/W 2 T Thermal resistance LQFP144, double sided PCB with 2 internal planes3 JA -- -- 32 C/W 3 Junction to Board LQFP 144 JB -- -- 22 C/W 4 Junction to Case LQFP 1444 JC -- -- 7/4 C/W JT -- -- 3 C/W 5 5 Junction to Package Top LQFP144 LQFP112 6 T Thermal resistance LQFP112, single sided PCB2 JA -- -- 433/494 C/W 7 T Thermal resistance LQFP112, double sided PCB with 2 internal planes5 JA -- -- 323/394 C/W 8 Junction to Board LQFP112 JB -- -- 223/274 C/W 9 4 C/W Junction to Case LQFP112 5 10 Junction to Package Top LQFP112 JC -- -- 73/114 JT -- -- 3/2 C/W JA -- -- 453/494 C/W C/W QFP80 11 12 T Thermal resistance QFP 80, double sided PCB with 2 internal planes3 JA -- -- 13 T Junction to Board QFP 80 JB -- -- 193/204 C/W T 6 C/W C/W 15 2 3 4 5 6 7 Thermal resistance QFP 80, single sided PCB2 333/364 14 1 T T Junction to Case QFP 80 Junction to Package Top QFP 80 7 JC -- -- 113/144 JT -- -- 3 The values for thermal resistance are achieved by package simulations Junction to ambient thermal resistance, JA was simulated to be equivalent to the JEDEC specification JESD51-2 in a horizontal configuration in natural convection. Maskset L15Y / M84E in LQFP112 or QFP80 Maskset M42E in LQFP112 or QFP80 Junction to ambient thermal resistance, JA was simulated to be equivalent to the JEDEC specification JESD51-7 in a horizontal configuration in natural convection. Junction to case thermal resistance was simulated to be equivalent to the measured values using the cold plate technique with the cold plate temperature used as the "case" temperature. This basic cold plate measurement technique is described by MIL-STD 883D, Method 1012.1. This is the correct thermal metric to use to calculate thermal performance when the package is being used with a heat sink. Thermal characterization parameter JT is the "resistance" from junction to reference point thermocouple on top center of the case as defined in JESD51-2. JT is a useful value to use to estimate junction temperature in a steady state customer enviroment. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1245 Appendix A Electrical Characteristics A.1.9 I/O Characteristics This section describes the characteristics of all I/O pins except EXTAL, XTAL,XFC,TEST,VREGEN and supply pins. CAUTION The internal pull up/pull down device specification is different depending on maskset. Table A-6. 3.3-V I/O Characteristics Conditions are 3.15 V < VDD35 < 3.6 V temperature from -40C to +140C, unless otherwise noted I/O Characteristics for all I/O pins except EXTAL, XTAL,XFC,TEST, VREGEN and supply pins. Num C Symbol Min Typ Max Unit P Input high voltage VIH 0.65*VDD35 -- -- V T Input high voltage VIH -- -- VDD35 + 0.3 V P Input low voltage VIL -- -- 0.35*VDD35 V T Input low voltage VIL VSS35 - 0.3 -- -- V 3 C Input hysteresis VHYS 4 C Input leakage current (pins in high impedance input mode)1 Vin = VDD35 or VSS35 5 C Output high voltage (pins in output mode) Partial drive IOH = -0.75 mA 6 1 2 Rating 250 mV -1 -- 1 A V OH VDD35 - 0.4 -- -- V P Output high voltage (pins in output mode) Full drive IOH = -4 mA VOH VDD35 - 0.4 -- -- V 7 C Output low voltage (pins in output mode) Partial Drive IOL = +0.9 mA VOL -- -- 0.4 V 8 P Output low voltage (pins in output mode) Full Drive IOL = +4.75 mA V -- -- 0.4 V Iin OL Internal pull up/pull down device specification (items 9 to 12) only valid for masksets 0L15Y & 1L15Y 9 P Internal pull up device current, tested at VIL max. IPUL -- -- -60 A 10 C Internal pull up device current, tested at VIH min. IPUH -6 -- - A 11 P Internal pull down device current, tested at VIH min. IPDH -- -- 60 A 12 C Internal pull down device current, tested at VIL max. IPDL 6 -- -- A Internal pull up/pull down device specification (items 13 to 14) valid for all other masksets 13 P Internal pull up resistance VIH min > input voltage > VIL max RPUL 25 55 K 14 P Internal pull down resistance VIH min > input voltage > VIL max RPDH 25 55 K 15 D Input capacitance Cin -- -- pF IICS IICP -2.5 -25 16 2 T Injection current Single pin limit Total device limit, sum of all injected currents 6 -- mA 2.5 25 MC9S12XDP512 Data Sheet, Rev. 2.21 1246 Freescale Semiconductor Appendix A Electrical Characteristics Table A-6. 3.3-V I/O Characteristics Conditions are 3.15 V < VDD35 < 3.6 V temperature from -40C to +140C, unless otherwise noted I/O Characteristics for all I/O pins except EXTAL, XTAL,XFC,TEST, VREGEN and supply pins. 17 C Port H, J, P interrupt input pulse filtered3 tPULSE -- -- 3 s 18 3 tPULSE 10 -- -- s C Port H, J, P interrupt input pulse passed 1 Maximum leakage current occurs at maximum operating temperature. Current decreases by approximately one-half for each 8 C to 12 C in the temper ature range from 50C to 125C. 2 Refer to Section A.1.4, "Current Injection" for more details 3 Parameter only applies in stop or pseudo stop mode. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1247 Appendix A Electrical Characteristics Table A-7. 5-V I/O Characteristics Conditions are 4.5 V < VDD35 < 5.5 V temperature from -40C to +140C, unless otherwise noted I/O Characteristics for all I/O pins except EXTAL, XTAL,XFC,TEST, VREGEN and supply pins. Num C 1 Rating Symbol Min Typ Max Unit 0.65*VDD35 -- -- V P Input high voltage V T Input high voltage VIH -- -- VDD35 + 0.3 V P Input low voltage VIL -- -- 0.35*VDD35 V T Input low voltage VIL VSS35 - 0.3 -- -- V 3 C Input hysteresis VHYS 250 -- mV 4 P Input leakage current (pins in high impedance input mode)1 Measured at Vin = 5.5V and Vin=0V 5 2 IH I -1 -- 1 A C Output high voltage (pins in output mode) Partial drive IOH = -2 mA V OH VDD35 - 0.8 -- -- V 6 P Output high voltage (pins in output mode) Full drive IOH = -10 mA VOH VDD35 - 0.8 -- -- V 7 C Output low voltage (pins in output mode) Partial drive IOL = +2 mA VOL -- -- 0.8 V 8 P Output low voltage (pins in output mode) Full drive IOL = +10 mA V -- -- 0.8 V in OL Internal pull up/pull down device specification (items 9 to 12) only valid for masksets 0L15Y & 1L15Y 9 P Internal pull up device current, tested at VIL max IPUL -- -- -130 A 10 C Internal pull up device current, tested at VIH min IPUH -10 -- -- A 11 P Internal pull down device current, tested at VIH min IPDH -- -- 130 A 12 C Internal pull down device current, tested at VIL max IPDL 10 -- -- A Internal pull up/pull down device specification (items 13 to 14) valid for all other masksets 13 P Internal pull up resistance VIH min > input voltage > VIL max RPUL 25 55 K 14 P Internal pull down resistance VIH min > input voltage > VIL max RPDH 25 55 K 15 D Input capacitance Cin -- -- pF IICS IICP -2.5 -25 16 2 T Injection current Single pin limit Total device Limit, sum of all injected currents 6 -- mA 2.5 25 17 P Port H, J, P interrupt input pulse filtered3 tPULSE -- -- 3 s 18 3 tPULSE 10 -- -- s P Port H, J, P interrupt input pulse passed 1 Maximum leakage current occurs at maximum operating temperature. Current decreases by approximately one-half for each 8 C to 12 C in the temper ature range from 50C to 125C. 2 Refer to Section A.1.4, "Current Injection" for more details 3 Parameter only applies in stop or pseudo stop mode. MC9S12XDP512 Data Sheet, Rev. 2.21 1248 Freescale Semiconductor Appendix A Electrical Characteristics Table A-8. I/O Characteristics for Port C, D, PE5, PE6, and PK7 for Reduced Input Voltage Thresholds Conditions are 4.5 V < VDD35 < 5.5 V Temperature from -40C to +140C, unless otherwise noted Num C Rating Symbol Min Typ Max Unit 1 P Input high voltage VIH 1.75 -- -- V 2 P Input low voltage VIL -- -- 0.75 V 3 C Input hysteresis VHYS -- 100 -- mV A.1.10 Supply Currents This section describes the current consumption characteristics of the device as well as the conditions for the measurements. A.1.10.1 Measurement Conditions All measurements are without output loads. Unless otherwise noted the currents are measured in single chip mode and the CPU and XGATE code is executed from RAM, VDD35=5.5V, internal voltage regulator is enabled and the bus frequency is 40MHz using a 4-MHz external clock source (PE7=XCLKS=0). Production testing is performed using a square wave signal at the EXTAL input. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1249 Appendix A Electrical Characteristics Table A-9. shows the configuration of the peripherals for run current measurement. Table A-9. Peripheral Configurations for Run Supply Current Measurements Peripheral Configuration MSCAN configured to loop-back mode using a bit rate of 1Mbit/s SPI configured to master mode, continously transmit data (0x55 or 0xAA) at 1Mbit/s SCI configured into loop mode, continously transmit data (0x55) at speed of 57600 baud IIC operate in master mode and continously transmit data (0x55 or 0xAA) at the bit rate of 100Kbit/s PWM configured to toggle its pins at the rate of 40kHz ECT the peripheral shall be configured to output compare mode, Pulse accumulator and modulus counter enabled. ATD the peripheral is configured to operate at its maximum specified frequency and to continuously convert voltages on all input channels in sequence. XGATE XGATE fetches code from RAM, XGATE runs in an infinite loop , it reads the Status and Flag registers of CAN's, SPI's, SCI's in sequence and does some bit manipulation on the data COP COP Warchdog Rate 224 RTI enabled, RTI Control Register (RTICTL) set to $FF API the module is configured to run from the RC oscillator clock source. PIT PIT is enabled, Micro-timer register 0 and 1 loaded with $0F and timer registers 0 to 3 are loaded with $03/07/0F/1F. DBG the module is enabled and the comparators are configured to trigger in outside range. The range covers all the code executed by the core. MC9S12XDP512 Data Sheet, Rev. 2.21 1250 Freescale Semiconductor Appendix A Electrical Characteristics A.1.10.2 Additional Remarks In expanded modes the currents flowing in the system are highly dependent on the load at the address, data, and control signals as well as on the duty cycle of those signals. No generally applicable numbers can given. A very good estimate is to take the single chip currents and add the currents due to the external loads. Table A-10. Run and Wait Current Characteristics Conditions are shown in Table A-4 unless otherwise noted Num C Rating Symbol Min Typ Max Unit 110 mA 95 mA Run supply current (Peripheral Configuration see Table A-9.) 1 P 1 IDD35 Peripheral Set fosc=4MHz, fbus=40MHz C T T Peripheral Set1 fosc=4MHz, fbus=40MHz fosc=4MHz, fbus=20MHz fosc=4MHz, fbus=8MHz 90 45 18 T T T Peripheral Set2 fosc=4MHz, fbus=40MHz fosc=4MHz, fbus=20MHz fosc=4MHz, fbus=8MHz 70 35 15 T T T Peripheral Set3 fosc=4MHz, fbus=40MHz fosc=4MHz, fbus=20MHz fosc=4MHz, fbus=8MHz 60 30 13 T T T Peripheral Set4 fosc=4MHz, fbus=40MHz fosc=4MHz, fbus=20MHz fosc=4MHz, fbus=8MHz 56 28 12 T T T Peripheral Set5 fosc=4MHz, fbus=40MHz fosc=4MHz, fbus=20MHz fosc=4MHz, fbus=8MHz 53 26 11 T T T Peripheral Set6 fosc=4MHz, fbus=40MHz fosc=4MHz, fbus=20MHz fosc=4MHz, fbus=8MHz 50 25 10 2 3 4 5 6 7 Wait supply current 8 P 10 2 3 4 5 6 Peripheral Set ,PLL on XGATE executing code from RAM T T Peripheral Set2 fosc=4MHz, fbus=40MHz fosc=4MHz, fbus=8MHz P All modules disabled, RTI enabled, PLL off 9 1 1 IDDW 50 10 10 The following peripherals are on: ATD0/ATD1/ECT/IIC1/PWM/SPI0-SPI2/SCI0-SCI2/CAN0-CAN4/XGATE The following peripherals are on: ATD0/ATD1/ECT/IIC1/PWM/SPI0-SPI2/SCI0-SCI2/CAN0-CAN4 The following peripherals are on: ATD0/ATD1/ECT/IIC1/PWM/SPI0-SPI2/SCI0-SCI2/ The following peripherals are on: ATD0/ATD1/ECT/IIC1/PWM/SPI0-SPI2 The following peripherals are on: ATD0/ATD1/ECT/IIC1/PWM/ The following peripherals are on: ATD0/ATD1/ECT/IIC1/ MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1251 Appendix A Electrical Characteristics Table A-11. Pseudo Stop and Full Stop Current Conditions are shown in Table A-4 unless otherwise noted Num C Rating Symbol Min Typ Max Unit 200 300 400 500 600 800 1000 1200 1500 -- 500 -- -- 2500 -- 3500 -- 7000 A Pseudo stop current (API, RTI, and COP disabled) PLL off 10 C P C C P C P C P -40C 27C 70C 85C "C" Temp Option 100C 105C "V" Temp Option 120C 125C "M" Temp Option 140C 11 C C C C C C C -40C 27C 70C 85C 105C 125C 140C 12 C P C C P C P C P -40C 27C 70C 85C "C" Temp Option 100C 105C "V" Temp Option 120C 125C "M" Temp Option 140C IDDPS -- -- -- -- -- -- -- -- -- Pseudo stop current (API, RTI, and COP enabled) PLL off IDDPS -- -- -- -- -- -- -- 500 750 850 1000 1200 1500 2000 -- -- -- -- -- -- -- A IDDS -- -- -- -- -- -- -- -- -- 20 30 100 200 250 400 500 600 1000 -- 100 -- -- 2000 -- 3000 -- 7000 A Stop Current MC9S12XDP512 Data Sheet, Rev. 2.21 1252 Freescale Semiconductor Appendix A Electrical Characteristics A.2 ATD Characteristics This section describes the characteristics of the analog-to-digital converter. A.2.1 ATD Operating Characteristics The Table A-12 and Table A-13 show conditions under which the ATD operates. The following constraints exist to obtain full-scale, full range results: VSSA VRL VIN VRH VDDA. This constraint exists since the sample buffer amplifier can not drive beyond the power supply levels that it ties to. If the input level goes outside of this range it will effectively be clipped. Table A-12. ATD 5-V Operating Characteristics Conditions are shown in Table A-4 unless otherwise noted, supply voltage 4.5 V < VDDA < 5.5 V Num C 1 2 D Reference potential Low High Symbol Min Typ Max Unit VRL VRH VSSA VDDA/2 -- -- VDDA/2 VDDA V V 5.00 5.5 V 2.0 MHz 2 C Differential reference voltage1 VRH-VRL 4.50 3 D ATD clock frequency fATDCLK 0.5 4 D ATD 10-bit conversion period Clock cycles2 Conv, time at 2.0 MHz ATD clock fATDCLK NCONV10 TCONV10 14 7 -- -- 28 14 Cycles s D ATD 8-Bit conversion period Clock cycles2 Conv, time at 2.0 MHz ATD clock fATDCLK NCONV8 TCONV8 12 6 -- -- 26 13 Cycles s 5 1 Rating 6 D Recovery time (VDDA = 5.0 Volts) tREC -- -- 20 s 7 P Reference supply current 2 ATD blocks on IREF -- -- 0.750 mA 8 P Reference supply current 1 ATD block on IREF -- -- 0.375 mA Full accuracy is not guaranteed when differential voltage is less than 4.50 V The minimum time assumes a final sample period of 2 ATD clocks cycles while the maximum time assumes a final sample period of 16 ATD clocks. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1253 Appendix A Electrical Characteristics Table A-13. ATD Operating Characteristics 3.3V Conditions are shown in Table A-4 unless otherwise noted, Supply Voltage 3.15V < VDDA < 3.6V Num C 1 2 D Reference potential Low High Symbol Min Typ Max Unit VRL VRH VSSA VDDA/2 -- -- VDDA/2 VDDA V V 2 C Differential reference voltage1 VRH-VRL 3.15 3.3 3.6 V 3 D ATD clock frequency fATDCLK 0.5 -- 2.0 MHz 4 D ATD 10-bit conversion period Clock cycles2 Conv, time at 2.0 MHz ATD clock fATDCLK NCONV10 TCONV10 14 7 -- -- 28 14 Cycles s D ATD 8-bit conversion period Clock cycles2 Conv, time at 2.0 MHz ATD clock fATDCLK NCONV8 TCONV8 12 6 -- -- 26 13 Cycles s 5 1 Rating 6 D Recovery time (VDDA = 5.0 Volts) tREC -- -- 20 s 7 P Reference supply current 2 ATD blocks on IREF -- -- 0.500 mA 8 P Reference supply current 1 ATD block on IREF -- -- 0.250 mA Full accuracy is not guaranteed when differential voltage is less than 3.15 V The minimum time assumes a final sample period of 2 ATD clocks cycles while the maximum time assumes a final sample period of 16 ATD clocks. A.2.2 Factors Influencing Accuracy Three factors -- source resistance, source capacitance and current injection -- have an influence on the accuracy of the ATD. A.2.2.1 Source Resistance Due to the input pin leakage current as specified in Table A-7 in conjunction with the source resistance there will be a voltage drop from the signal source to the ATD input. The maximum source resistance RS specifies results in an error of less than 1/2 LSB (2.5 mV) at the maximum leakage current. If device or operating conditions are less than worst case or leakage-induced error is acceptable, larger values of source resistance is allowed. A.2.2.2 Source Capacitance When sampling an additional internal capacitor is switched to the input. This can cause a voltage drop due to charge sharing with the external and the pin capacitance. For a maximum sampling error of the input voltage 1LSB, then the external filter capacitor, Cf 1024 * (CINS-CINN). MC9S12XDP512 Data Sheet, Rev. 2.21 1254 Freescale Semiconductor Appendix A Electrical Characteristics A.2.2.3 Current Injection There are two cases to consider. 1. A current is injected into the channel being converted. The channel being stressed has conversion values of $3FF ($FF in 8-bit mode) for analog inputs greater than VRH and $000 for values less than VRL unless the current is higher than specified as disruptive condition. 2. Current is injected into pins in the neighborhood of the channel being converted. A portion of this current is picked up by the channel (coupling ratio K), This additional current impacts the accuracy of the conversion depending on the source resistance. The additional input voltage error on the converted channel can be calculated as: VERR = K * RS * IINJ with IINJ being the sum of the currents injected into the two pins adjacent to the converted channel. Table A-14. ATD Electrical Characteristics Conditions are shown in Table A-4 unless otherwise noted Num C 1 C Max input source resistance 2 T Total input capacitance Non sampling Sampling Symbol Min Typ Max Unit RS -- -- 1 K CINN CINS -- -- -- -- 10 22 pF 3 C Disruptive analog input current1 INA -2.5 -- 2.5 mA 4 C Coupling ratio positive current injection Kp -- -- 10-4 A/A -- 10-2 A/A 5 1 Rating C Coupling ratio negative current injection Kn -- See also Table A-7. item 14 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1255 Appendix A Electrical Characteristics A.2.3 A.2.3.1 ATD Accuracy 5-V Range Table A-15 specifies the ATD conversion performance excluding any errors due to current injection, input capacitance, and source resistance. Table A-15. 5-V ATD Conversion Performance Conditions are shown in Table A-4 unless otherwise noted VREF = VRH-VRL = 5.12 V. Resulting to one 8-bit count = 20 mV and one 10-bit count = 5 mV fATDCLK = 2.0 MHz Num C Symbol Min Typ Max Unit 1 P 10-bit resolution LSB -- 5 -- mV 2 P 10-bit differential nonlinearity DNL -1 -- 1 Counts 3 P 10-bit integral nonlinearity INL -2.5 1.5 2.5 Counts 1 4 P 10-bit absolute error AE -3 2.0 3 Counts 5 P 8-bit resolution LSB -- 20 -- mV 6 P 8-bit differential nonlinearity DNL -0.5 -- 0.5 Counts 7 P 8-bit integral nonlinearity INL -1.0 0.5 1.0 Counts AE -1.5 1.0 1.5 Counts 8 1 Rating 1 P 8-bit absolute error These values include the quantization error which is inherently 1/2 count for any A/D converter. A.2.3.2 3.3-V Range Table A-16 specifies the ATD conversion performance excluding any errors due to current injection, input capacitance, and source resistance. Table A-16. 3.3-V ATD Conversion Performance Conditions are shown in Table A-4 unless otherwise noted VREF = VRH-VRL = 3.328 V. Resulting to one 8-bit count = 13mV and one 10-bit count = 3.25 mV fATDCLK = 2.0 MHz Num C Symbol Min Typ Max Unit 1 P 10-bit resolution LSB -- 3.25 -- mV 2 P 10-bit differential nonlinearity DNL -1.5 -- 1.5 Counts 3 P 10-bit integral nonlinearity INL -3.5 1.5 3.5 Counts AE -5 2.5 5 Counts 1 4 P 10-bit absolute error 5 P 8-bit resolution LSB -- 13 -- mV 6 P 8-bit differential nonlinearity DNL -0.5 -- 0.5 Counts 7 P 8-bit integral nonlinearity INL -1.5 1.0 1.5 Counts AE -2.0 1.5 2.0 Counts 8 1 Rating P 8-bit absolute error 1 These values include the quantization error which is inherently 1/2 count for any A/D converter. MC9S12XDP512 Data Sheet, Rev. 2.21 1256 Freescale Semiconductor Appendix A Electrical Characteristics A.2.3.3 ATD Accuracy Definitions For the following definitions see also Figure A-1. Differential non-linearity (DNL) is defined as the difference between two adjacent switching steps. V -V i i-1 DNL ( i ) = --------------------------- - 1 1LSB The integral non-linearity (INL) is defined as the sum of all DNLs: n INL ( n ) = V -V n 0 DNL ( i ) = --------------------- - n 1LSB i=1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1257 Appendix A Electrical Characteristics DNL Vi-1 10-Bit Absolute Error Boundary LSB Vi $3FF 8-Bit Absolute Error Boundary $3FE $3FD $FF $3FC $3FB $3FA $3F9 $FE $3F8 $3F7 $3F6 $3F5 10-Bit Resolution $3F3 9 Ideal Transfer Curve 2 8 8-Bit Resolution $FD $3F4 7 10-Bit Transfer Curve 6 5 1 4 3 8-Bit Transfer Curve 2 1 0 5 10 15 20 25 30 35 40 50 50555060506550705075508050855090509551005105511051155120 Vin mV Figure A-1. ATD Accuracy Definitions NOTE Figure A-1 shows only definitions, for specification values refer to Table A-15. MC9S12XDP512 Data Sheet, Rev. 2.21 1258 Freescale Semiconductor Appendix A Electrical Characteristics A.3 NVM, Flash, and EEPROM NOTE Unless otherwise noted the abbreviation NVM (nonvolatile memory) is used for both Flash and EEPROM. A.3.1 NVM Timing The time base for all NVM program or erase operations is derived from the oscillator. A minimum oscillator frequency fNVMOSC is required for performing program or erase operations. The NVM modules do not have any means to monitor the frequency and will not prevent program or erase operation at frequencies above or below the specified minimum. Attempting to program or erase the NVM modules at a lower frequency a full program or erase transition is not assured. The Flash and EEPROM program and erase operations are timed using a clock derived from the oscillator using the FCLKDIV and ECLKDIV registers respectively. The frequency of this clock must be set within the limits specified as fNVMOP. The minimum program and erase times shown in Table A-17 are calculated for maximum fNVMOP and maximum fbus. The maximum times are calculated for minimum fNVMOP and a fbus of 2 MHz. A.3.1.1 Single Word Programming The programming time for single word programming is dependant on the bus frequency as a well as on the frequency fNVMOP and can be calculated according to the following formula. t A.3.1.2 swpgm 1 1 = 9 ------------------------- + 25 -----------f f bus NVMOP Burst Programming This applies only to the Flash where up to 64 words in a row can be programmed consecutively using burst programming by keeping the command pipeline filled. The time to program a consecutive word can be calculated as: t bwpgm 1 1 = 4 ------------------------- + 9 -----------f f NVMOP bus The time to program a whole row is: t brpgm = t swpgm + 63 t bwpgm Burst programming is more than 2 times faster than single word programming. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1259 Appendix A Electrical Characteristics A.3.1.3 Sector Erase Erasing a 1024-byte Flash sector or a 4-byte EEPROM sector takes: t era 1 4000 ------------------------f NVMOP The setup time can be ignored for this operation. A.3.1.4 Mass Erase Erasing a NVM block takes: t mass 1 20000 ------------------------f NVMOP The setup time can be ignored for this operation. A.3.1.5 Blank Check The time it takes to perform a blank check on the Flash or EEPROM is dependant on the location of the first non-blank word starting at relative address zero. It takes one bus cycle per word to verify plus a setup of the command. t check location t cyc + 10 t cyc MC9S12XDP512 Data Sheet, Rev. 2.21 1260 Freescale Semiconductor Appendix A Electrical Characteristics Table A-17. NVM Timing Characteristics Conditions are shown in Table A-4 unless otherwise noted Num C 6 7 Unit -- 801 MHz 2 D Bus frequency for programming or erase operations fNVMBUS 1 -- -- MHz 3 D Operating frequency fNVMOP 150 -- 200 tswpgm 2 P Single word programming time D Flash burst programming consecutive word 6 D Flash burst programming time for 64 words 7 P Sector erase time 10 5 Max 0.5 9 4 Typ fNVMOSC 8 3 Min D External oscillator clock 5 2 Symbol 1 4 1 Rating P Mass erase time D Blank check time Flash per block D Blank check time EEPROM per block 4 4 46 2 tbwpgm 20.4 2 kHz 3 -- 74.5 -- 3 31 s s 3 tbrpgm 1331.2 -- 2027.5 s tera 205 -- 26.73 ms -- 3 ms 5 tmass 100 tcheck 11 6 11 6 tcheck 133 7 -- 65546 -- 7 2058 tcyc tcyc Restrictions for oscillator in crystal mode apply. Minimum programming times are achieved under maximum NVM operating frequency fNVMOP and maximum bus frequency fbus. Maximum erase and programming times are achieved under particular combinations of fNVMOP and bus frequency fbus. Refer to formulae in Sections Section A.3.1.1, "Single Word Programming" - Section A.3.1.4, "Mass Erase" for guidance. Burst programming operations are not applicable to EEPROM Minimum erase times are achieved under maximum NVM operating frequency, fNVMOP. Minimum time, if first word in the array is not blank Maximum time to complete check on an erased block MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1261 Appendix A Electrical Characteristics A.3.2 NVM Reliability The reliability of the NVM blocks is guaranteed by stress test during qualification, constant process monitors and burn-in to screen early life failures. The program/erase cycle count on the sector is incremented every time a sector or mass erase event is executed Table A-18. NVM Reliability Characteristics1 Conditions are shown in Table A-4 unless otherwise noted Num C Rating Symbol Min Typ Max Unit 15 1002 -- Years 20 1002 -- 10,000 -- -- 10,000 100,0003 -- 15 1002 -- 20 1002 -- 10,000 -- -- 100,000 300,0003 -- Flash Reliability Characteristics 1 C Data retention after 10,000 program/erase cycles at an average junction temperature of TJavg 85C 2 C Data retention with <100 program/erase cycles at an average junction temperature TJavg 85C 3 C Number of program/erase cycles (-40C TJ 0C) 4 C Number of program/erase cycles (0C TJ 140C) tFLRET nFL Cycles EEPROM Reliability Characteristics 5 C Data retention after up to 100,000 program/erase cycles at an average junction temperature of TJavg 85C 6 C Data retention with <100 program/erase cycles at an average junction temperature TJavg 85C 7 C Number of program/erase cycles (-40C TJ 0C) 8 C Number of program/erase cycles (0C < TJ 140C) tEEPRET nEEP Years Cycles 1 TJavg will not exeed 85C considering a typical temperature profile over the lifetime of a consumer, industrial or automotive application. 2 Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to 25C using the Arrhenius equation. For additional information on how Freescale defines Typical Data Retention, please refer to Engineering Bulletin EB618. 3 Spec table quotes typical endurance evaluated at 25C for this product family, typical endurance at various temperature can be estimated using the graph below. For additional information on how Freescale defines Typical Endurance, please refer to Engineering Bulletin EB619. MC9S12XDP512 Data Sheet, Rev. 2.21 1262 Freescale Semiconductor Appendix A Electrical Characteristics Figure A-2. Typical Endurance vs Temperature 500 Typical Endurance [103 Cycles] 450 400 350 300 250 200 150 100 50 0 -40 -20 0 20 40 60 80 100 120 140 Operating Temperature TJ [C] ------ Flash ------ EEPROM MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1263 Appendix A Electrical Characteristics A.4 Voltage Regulator Table A-19. Voltage Regulator Electrical Characteristics Num C 1 P Input voltages 2 P Output voltage core Full performance mode Reduced power mode Shutdown mode VDD Output Voltage PLL Full Performance Mode Reduced power mode Shutdown mode VDDPLL 3 4 5 6 7 1 2 3 4 5 6 7 P P P C C Characteristic Low-voltage interrupt3 Assert level Deassert level Low-voltage reset4 5 Assert level Symbol Min Typ Max Unit VVDDR,A 3.15 -- 5.5 V 2.35 1.4 -- 2.54 2.25 --1 2.75 2.75 -- V V V 2.35 1.25 -- 2.54 2.25 --2 2.75 2.75 -- V V V 4.0 4.15 4.37 4.52 4.66 4.77 V V 2.25 -- -- V VPORA VPORD 0.97 -- -- -- -- 2.05 V V dfAPI - 10% -- + 10% -- VLVIA VLVID VLVRA 6 Power-on reset Assert level Deassert level Trimmed API internal clock7 f / fnominal High impedance output High impedance output Monitors VDDA, active only in full performance mode. Indicates I/O and ADC performance degradation due to low supply voltage. Monitors VDD, active only in full performance mode. MCU is monitored by the POR in RPM (see Figure A-1) Digital functionality is guaranteed in the range between VDD(min) and VLVRA(min). Monitors VDD. Active in all modes. The API Trimming bits must be set that the minimum periode equals to 0.2 ms. fnominal = 1/0.2ms MC9S12XDP512 Data Sheet, Rev. 2.21 1264 Freescale Semiconductor Appendix A Electrical Characteristics A.4.1 Chip Power-up and Voltage Drops MC9S12XDP512 sub modules LVI (low voltage interrupt), POR (power-on reset) and LVR (low voltage reset) handle chip power-up or drops of the supply voltage. Figure 0-1 MC9S12XDP512 - Chip Power-up and Voltage Drops (not scaled) V VDDA VLVID VLVIA VDD VLVRD VLVRA VPORD t LVI LVI enabled LVI disabled due to LVR POR LVR A.4.2 A.4.2.1 Output Loads Resistive Loads On-chip voltage regulator MC9S12XDP512 intended to supply the internal logic and oscillator circuits allows no external DC loads. A.4.2.2 Capacitive Loads The capacitive loads are specified in Table A-20.. Ceramic capacitors with X7R dielectricum are required. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1265 Appendix A Electrical Characteristics Table A-20. MC9S12XDP512 - Capacitive Loads Num Characteristic 1 VDD external capacitive load 2 VDDPLL external capacitive load Symbol Min Recommended Max Unit CDDext 400 440 12000 nF CDDPLLext 90 220 5000 nF MC9S12XDP512 Data Sheet, Rev. 2.21 1266 Freescale Semiconductor Appendix A Electrical Characteristics A.5 Reset, Oscillator, and PLL This section summarizes the electrical characteristics of the various startup scenarios for oscillator and phase-locked loop (PLL). A.5.1 Startup Table A-21 summarizes several startup characteristics explained in this section. Detailed description of the startup behavior can be found in the Clock and Reset Generator (CRG) Block Guide. Table A-21. Startup Characteristics Conditions are shown in Table A-4unless otherwise noted Num C 1 D Reset input pulse width, minimum input time 2 D Startup from reset 3 D Interrupt pulse width, IRQ edge-sensitive mode 4 D Wait recovery startup time 5 1 2 Rating D Fast wakeup from STOP2 Symbol Min Typ Max Unit PWRSTL 2 -- -- tosc nRST 192 -- 196 nosc 1 -- -- ns PWIRQ 25 tWRS -- -- 14 tcyc tfws -- 50 -- s 1 tcycle at 40Mhz Bus Clock VDD1/VDD2 filter capacitors 220 nF, VDD35 = 5 V, T= 25C A.5.1.1 POR The release level VPORR and the assert level VPORA are derived from the VDD supply. They are also valid if the device is powered externally. After releasing the POR reset the oscillator and the clock quality check are started. If after a time tCQOUT no valid oscillation is detected, the MCU will start using the internal self clock. The fastest startup time possible is given by nuposc. A.5.1.2 SRAM Data Retention Provided an appropriate external reset signal is applied to the MCU, preventing the CPU from executing code when VDD35 is out of specification limits, the SRAM contents integrity is guaranteed if after the reset the PORF bit in the CRG flags register has not been set. A.5.1.3 External Reset When external reset is asserted for a time greater than PWRSTL the CRG module generates an internal reset, and the CPU starts fetching the reset vector without doing a clock quality check, if there was an oscillation before reset. A.5.1.4 Stop Recovery Out of stop the controller can be woken up by an external interrupt. A clock quality check as after POR is performed before releasing the clocks to the system. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1267 Appendix A Electrical Characteristics If the MCU is woken-up by an interrupt and the fast wake-up feature is enabled (FSTWKP = 1 and SCME = 1), the system will resume operation in self-clock mode after tfws. A.5.1.5 Pseudo Stop and Wait Recovery The recovery from pseudo stop and wait are essentially the same since the oscillator was not stopped in both modes. The controller can be woken up by internal or external interrupts. After twrs the CPU starts fetching the interrupt vector. A.5.2 Oscillator The device features an internal low-power loop controlled Pierce oscillator and a full swing Pierce oscillator/external clock mode. The selection of loop controlled Pierce oscillator or full swing Pierce oscillator/external clock depends on the XCLKS signal which is sampled during reset. Before asserting the oscillator to the internal system clocks the quality of the oscillation is checked for each start from either power-on, STOP or oscillator fail. tCQOUT specifies the maximum time before switching to the internal self clock mode after POR or STOP if a proper oscillation is not detected. The quality check also determines the minimum oscillator start-up time tUPOSC. The device also features a clock monitor. A clock monitor failure is asserted if the frequency of the incoming clock signal is below the assert frequency fCMFA. MC9S12XDP512 Data Sheet, Rev. 2.21 1268 Freescale Semiconductor Appendix A Electrical Characteristics Table A-22. Oscillator Characteristics Conditions are shown in Table A-4 unless otherwise noted Num 1a C Rating C Crystal oscillator range (loop controlled Pierce) 1, 2 Symbol Min Typ Max Unit fOSC 4.0 -- 16 MHz 1b C Crystal oscillator range (full swing Pierce) fOSC 0.5 -- 40 MHz 2 P Startup current iOSC 100 -- -- A 504 ms 2.5 s 3 3 C Oscillator start-up time (loop controlled Pierce) tUPOSC -- 4 D Clock quality check time-out tCQOUT 0.45 5 P Clock monitor failure assert frequency fCMFA 50 100 200 KHz 6 P External square wave input frequency fEXT 0.5 -- 80 MHz 7 D External square wave pulse width low tEXTL 5 -- -- ns 8 D External square wave pulse width high tEXTH 5 -- -- ns 9 D External square wave rise time tEXTR -- -- 1 ns 10 D External square wave fall time tEXTF -- -- 1 ns 11 D Input capacitance (EXTAL, XTAL inputs) 12 13 14 -- CIN -- 7 -- pF 5 P EXTAL pin input high voltage VIH,EXTAL 0.75* VDDPLL -- -- V T EXTAL pin input high voltage5 VIH,EXTAL -- -- VDDPLL + 0.3 V P EXTAL pin input low voltage5 VIL,EXTAL -- -- 0.25* VDDPLL V T EXTAL pin input low voltage5 VIL,EXTAL VSSPLL - 0.3 -- -- V C EXTAL pin input hysteresis5 VHYS,EXTAL -- 250 -- mV 1 Depending on the crystal a damping series resistor might be necessary XCLKS = 0 3 fosc = 4 MHz, C = 22 pF. 4 Maximum value is for extreme cases using high Q, low frequency crystals 5 If full swing Pierce oscillator/external clock circuitry is used. (XCLKS = 0) 2 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1269 Appendix A Electrical Characteristics A.5.3 Phase Locked Loop The oscillator provides the reference clock for the PLL. The PLLs voltage controlled oscillator (VCO) is also the system clock source in self clock mode. A.5.3.1 XFC Component Selection This section describes the selection of the XFC components to achieve a good filter characteristics. Cp VDDPLL Cs R XFC Pin Phase fosc fref 1 D refdv+1 VCO fvco KF fcmp KV Detector Loop Divider 1 synr+1 1 2 Figure A-3. Basic PLL Functional Diagram The following procedure can be used to calculate the resistance and capacitance values using typical values for K1, f1 and ich from Table A-23. The grey boxes show the calculation for fVCO = 80 MHz and fref = 4 MHz. For example, these frequencies are used for fOSC = 4-MHz and a 40-MHz bus clock. The VCO gain at the desired VCO frequency is approximated by: K V = K e 1 ( f 1 - f vco ) ---------------------------K 1 1V = - 195MHz V e 126 - 80 -------------------- 195 = -154.0MHz/V The phase detector relationship is given by: K = -i ch K V = - 3.5A ( - 154MHz V ) = 539.1Hz ich is the current in tracking mode. The loop bandwidth fC should be chosen to fulfill the Gardner's stability criteria by at least a factor of 10, typical values are 50. = 0.9 ensures a good transient response. MC9S12XDP512 Data Sheet, Rev. 2.21 1270 Freescale Semiconductor Appendix A Electrical Characteristics f f 2f ref ref 1 < ------------------------------------------- ----- f < ------------- ;( = 0.9 ) C C 4 10 10 2 + 1 + fC < 100kHz And finally the frequency relationship is defined as f VCO n = --------------- = 2 ( synr + 1 ) f ref = 20 With the above values the resistance can be calculated. The example is shown for a loop bandwidth fC = 20 kHz: 2nf C 2 20 20kHz R = ----------------------------- = ------------------------------------------ = 4.7k K ( 539.1Hz ) The capacitance Cs can now be calculated as: 2 2 0.516 C = ---------------------- = --------------- ;( = 0.9 ) s f R f R C C = 5.5nF = ~ 4.7nF The capacitance Cp should be chosen in the range of: C C s s ------ C p -----20 10 A.5.3.2 CP = 470pF Jitter Information The basic functionality of the PLL is shown in Figure A-3. With each transition of the clock fcmp, the deviation from the reference clock fref is measured and input voltage to the VCO is adjusted accordingly.The adjustment is done continuously with no abrupt changes in the clock output frequency. Noise, voltage, temperature and other factors cause slight variations in the control loop resulting in a clock jitter. This jitter affects the real minimum and maximum clock periods as illustrated in Figure A-4. 1 0 2 3 N-1 N tmin1 tnom tmax1 tminN tmaxN Figure A-4. Jitter Definitions MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1271 Appendix A Electrical Characteristics The relative deviation of tnom is at its maximum for one clock period, and decreases towards zero for larger number of clock periods (N). Defining the jitter as: t (N) t (N) max min J ( N ) = max 1 - ----------------------- , 1 - ----------------------- Nt Nt nom nom For N < 1000, the following equation is a good fit for the maximum jitter: j 1 J ( N ) = -------- + j N 2 J(N) 1 5 10 20 N Figure A-5. Maximum Bus Clock Jitter Approximation This is very important to notice with respect to timers, serial modules where a prescaler will eliminate the effect of the jitter to a large extent. MC9S12XDP512 Data Sheet, Rev. 2.21 1272 Freescale Semiconductor Appendix A Electrical Characteristics Table A-23. PLL Characteristics Conditions are shown in Table A-4 unless otherwise noted Num C 1 2 Rating Symbol Min Typ Max Unit 1 P Self clock mode frequency fSCM 1 -- 5.5 MHz 2 D VCO locking range fVCO 8 -- 80 MHz 3 D Lock detector transition from acquisition to tracking mode |trk| 3 -- 4 %1 4 D Lock detection |Lock| 0 -- 1.5 %1 5 D Unlock detection |unl| 0.5 -- 2.5 %1 6 D Lock detector transition from tracking to acquisition mode |unt| 6 -- 8 %1 7 C PLLON total stabilization delay (auto mode)2 tstab -- 0.24 -- ms 8 2 tacq -- 0.09 -- ms D PLLON acquisition mode stabilization delay 2 9 D PLLON tracking mode stabilization delay tal -- 0.16 -- ms 10 D Fitting parameter VCO loop gain K1 -- -195 -- MHz/V 11 D Fitting parameter VCO loop frequency f1 -- 126 -- MHz 12 D Charge pump current acquisition mode | ich | -- 38.5 -- A 13 D Charge pump current tracking mode | ich | -- 3.5 -- A 14 C Jitter fit parameter 1 2 j1 -- 0.9 1.3 % 15 C Jitter fit parameter 22 j2 -- 0.02 0.12 % % deviation from target frequency fosc = 4 MHz, fBUS = 40 MHz equivalent fVCO = 80 MHz: REFDV = #$00, SYNR = #$09, CS = 4.7 nF, CP = 470 pF, RS = 4.7 k A.6 MSCAN Table A-24. MSCAN Wake-up Pulse Characteristics Conditions are shown in Table A-4 unless otherwise noted Num C Rating Symbol Min Typ Max Unit 1 P MSCAN wakeup dominant pulse filtered tWUP -- -- 2 s 2 P MSCAN wakeup dominant pulse pass tWUP 5 -- -- s MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1273 Appendix A Electrical Characteristics A.7 SPI Timing This section provides electrical parametrics and ratings for the SPI. In Table A-25 the measurement conditions are listed. Table A-25. Measurement Conditions Description Drive mode Load capacitance CLOAD1, on all outputs Thresholds for delay measurement points 1 Value Unit Full drive mode -- 50 pF (20% / 80%) VDDX V Timing specified for equal load on all SPI output pins. Avoid asymmetric load. A.7.1 Master Mode In Figure A-6 the timing diagram for master mode with transmission format CPHA = 0 is depicted. SS1 (Output) 2 1 SCK (CPOL = 0) (Output) 5 12 13 3 6 MSB IN2 10 MOSI (Output) 13 4 SCK (CPOL = 1) (Output) MISO (Input) 12 4 Bit 6 . . . 1 LSB IN 9 MSB OUT2 Bit 6 . . . 1 11 LSB OUT 1. If configured as an output. 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure A-6. SPI Master Timing (CPHA = 0) In Figure A-7 the timing diagram for master mode with transmission format CPHA=1 is depicted. MC9S12XDP512 Data Sheet, Rev. 2.21 1274 Freescale Semiconductor Appendix A Electrical Characteristics SS1 (Output) 1 2 12 13 12 13 3 SCK (CPOL = 0) (Output) 4 4 SCK (CPOL = 1) (Output) 5 MISO (Input) 6 MSB IN2 Bit 6 . . . 1 11 9 MOSI (Output) Port Data LSB IN Master MSB OUT2 Bit 6 . . . 1 Master LSB OUT Port Data 1.If configured as output 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. Figure A-7. SPI Master Timing (CPHA = 1) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1275 Appendix A Electrical Characteristics In Table A-26 the timing characteristics for master mode are listed. Table A-26. SPI Master Mode Timing Characteristics Num C Characteristic Symbol Min Typ Max Unit 1 D SCK frequency fsck 1/2048 -- 1/2 fbus 1 D SCK period tsck 2 D Enable lead time tlead 2 -- 2048 tbus -- 1/2 -- tsck 3 D Enable lag time 4 D Clock (SCK) high or low time tlag -- 1/2 -- tsck twsck -- 1/2 -- tsck 5 D Data setup time (inputs) tsu 8 -- -- ns 6 D Data hold time (inputs) thi 8 -- -- ns 9 D Data valid after SCK edge tvsck -- -- 15 ns 10 D Data valid after SS fall (CPHA = 0) tvss -- -- 15 ns 11 D Data hold time (outputs) tho 0 -- -- ns 12 D Rise and fall time inputs trfi -- -- 8 ns 13 D Rise and fall time outputs trfo -- -- 8 ns Figure A-8. Derating of maximum fSCK to fbus ratio in Master Mode fSCK/fbus 1/2 1/4 5 10 15 20 25 30 35 40 fbus [MHz] In Master Mode the allowed maximum fSCK to fbus ratio (= minimum Baud Rate Divisor, pls. see SPI Section) derates with increasing fbus. A.7.2 Slave Mode In Figure A-9 the timing diagram for slave mode with transmission format CPHA = 0 is depicted. MC9S12XDP512 Data Sheet, Rev. 2.21 1276 Freescale Semiconductor Appendix A Electrical Characteristics SS (Input) 1 12 13 3 12 13 SCK (CPOL = 0) (Input) 4 2 4 SCK (CPOL = 1) (Input) 10 8 7 MISO (Output) 9 See Note Slave MSB 5 MOSI (Input) Bit 6 . . . 1 11 11 Slave LSB OUT See Note 6 MSB IN Bit 6 . . . 1 LSB IN NOTE: Not defined Figure A-9. SPI Slave Timing (CPHA = 0) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1277 Appendix A Electrical Characteristics In Figure A-10 the timing diagram for slave mode with transmission format CPHA = 1 is depicted. SS (Input) 3 1 2 12 13 12 13 SCK (CPOL = 0) (Input) 4 4 SCK (CPOL = 1) (Input) See Note 7 Slave MSB OUT 5 MOSI (Input) 8 11 9 MISO (Output) Bit 6 . . . 1 Slave LSB OUT 6 MSB IN Bit 6 . . . 1 LSB IN NOTE: Not defined Figure A-10. SPI Slave Timing (CPHA = 1) In Table A-27 the timing characteristics for slave mode are listed. Table A-27. SPI Slave Mode Timing Characteristics Num C 1 D 1 Symbol Min Typ Max Unit SCK frequency fsck DC -- 1/4 fbus D SCK period tsck 4 -- tbus 2 D Enable lead time tlead 4 -- -- tbus 3 D Enable lag time tlag 4 -- -- tbus 4 D Clock (SCK) high or low time twsck 4 -- -- tbus 5 D Data setup time (inputs) tsu 8 -- -- ns 6 D Data hold time (inputs) thi 8 -- -- ns 7 D Slave access time (time to data active) ta -- -- 20 ns 8 D Slave MISO disable time tdis -- -- 22 9 1 D Characteristic Data valid after SCK edge tvsck -- -- ns 29 + 0.5 tbus1 ns 29 + 0.5 tbus1 ns 10 D Data valid after SS fall tvss -- -- 11 D Data hold time (outputs) tho 20 -- -- ns 12 D Rise and fall time inputs trfi -- -- 8 ns 13 D Rise and fall time outputs trfo -- -- 8 ns 0.5 tbus added due to internal synchronization delay MC9S12XDP512 Data Sheet, Rev. 2.21 1278 Freescale Semiconductor Appendix A Electrical Characteristics A.8 External Bus Timing The following conditions are assumed for all following external bus timing values: * Crystal input within 45% to 55% duty * Equal loads of pins * Pad full drive (reduced drive must be off) A.8.1 Normal Expanded Mode (External Wait Feature Disabled) 1 1 CSx ADDRx ADDR1 2 ADDR2 3 RE 4 5 WE 8 6 7 10 DATAx (Read) DATA1 11 (Write) DATA2 9 EWAIT UDS, LDS Figure A-11. Example 1a: Normal Expanded Mode -- Read Followed by Write MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1279 Appendix A Electrical Characteristics Table A-28. Example 1a: Normal Expanded Mode Timing VDD35 = 5.0 V (EWAITE = 0) 1 No. C Characteristic -- -- Frequency of internal bus -- -- Internal cycle time -- -- Frequency of external bus 1 -- External cycle time (selected by EXSTR) 1 Symbol Min Max Unit fi D.C. 40.0 MHz tcyc 25 ns fo D.C. 20.0 MHz tcyce 50 ns 2 D Address valid to RE fall tADRE 5 -- ns 3 D Pulse width, RE PWRE 35 -- ns 1 4 D Address valid to WE fall tADWE 5 -- ns 5 D Pulse width, WE PWWE 23 -- ns 6 D Read data setup time (if ITHRS = 0) tDSR 24 -- ns D Read data setup time (if ITHRS = 1) tDSR 28 -- ns 7 D Read data hold time tDHR 0 -- ns 8 D Read enable access time tACCR 11 -- ns 9 D Write data valid to WE fall tWDWE 7 -- ns 10 D Write data setup time tDSW 31 -- ns 11 D Write data hold time tDHW 8 -- ns Includes the following signals: ADDRx, UDS, LDS, and CSx. MC9S12XDP512 Data Sheet, Rev. 2.21 1280 Freescale Semiconductor Appendix A Electrical Characteristics A.8.2 Normal Expanded Mode (External Wait Feature Enabled) 1 CSx ADDRx ADDR1 2 ADDR2 3 RE WE 8 6 7 (Read) DATA1 DATAx 12 13 EWAIT UDS, LDS Figure A-12. Example 1b: Normal Expanded Mode -- Stretched Read Access MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1281 Appendix A Electrical Characteristics 1 CSx ADDRx ADDR1 ADDR2 RE 4 5 WE 9 10 DATAx 11 (Write) DATA1 12 13 EWAIT UDS, LDS Figure A-13. Example 1b: Normal Expanded Mode -- Stretched Write Access MC9S12XDP512 Data Sheet, Rev. 2.21 1282 Freescale Semiconductor Appendix A Electrical Characteristics Table A-29. Example 1b: Normal Expanded Mode Timing VDD35 = 5.0 V (EWAITE = 1) No. C Characteristic 2 Symbol 3 Stretch Cycles Unit Min Max Min Max fi D.C. 40.0 D.C. 40.0 MHz tcyc 25 25 ns fo D.C. 13.3 D.C. 10.0 MHz -- -- Frequency of internal bus -- -- Internal cycle time -- -- Frequency of external bus -- -- External cycle time (selected by EXSTR) tcyce 75 100 ns 1 -- External cycle time (EXSTR+1EWAIT) tcycew 100 125 ns 2 D Address1 valid to RE fall tADRE 5 -- 5 -- ns 3 D Pulse width, RE 2 PWRE 85 -- 110 -- ns 4 D Address1 valid to WE fall tADWE 5 -- 5 -- ns 5 D Pulse width, WE2 PWWE 73 -- 98 -- ns D Read data setup time (if ITHRS = 0) tDSR 24 -- 24 -- ns D Read data setup time (if ITHRS = 1) tDSR 28 -- 28 -- ns 7 D Read data hold time tDHR 0 -- 0 -- ns 8 D Read enable access time tACCR 71 -- 86 -- ns 9 D Write data valid to WE fall tWDWE 7 -- 7 -- ns 10 D Write data setup time tDSW 81 -- 106 -- ns 11 D Write data hold time tDHW 8 -- 8 -- ns 12 D Address to EWAIT fall tADWF 0 20 0 45 ns 13 D Address to EWAIT rise tADWR 37 47 62 72 ns 6 1 2 Stretch Cycles Includes the following signals: ADDRx, UDS, LDS, and CSx. Affected by EWAIT. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1283 Appendix A Electrical Characteristics A.8.3 Emulation Single-Chip Mode (Without Wait States) 1 1 2 3 ECLK2X ECLK 5 4 7 6 ADDR [22:20]/ ACC [2:0] ADDR1 ACC1 ADDR2 ACC2 ADDR3 ADDR [19:16]/ IQSTAT [3:0] ADDR1 IQSTAT0 ADDR2 IQSTAT1 ADDR3 ADDR [15:0]/ IVD [15:0] ADDR1 IVD0 ADDR2 IVD1 ADDR3 8 9 DATAx DATA0 (Read) DATA1 (Write) DATA2 10 12 11 12 R/W LSTRB Figure A-14. Example 2a: Emulation Single-Chip Mode -- Read Followed by Write MC9S12XDP512 Data Sheet, Rev. 2.21 1284 Freescale Semiconductor Appendix A Electrical Characteristics Table A-30. Example 2a: Emulation Single-Chip Mode Timing VDD35 = 5.0 V (EWAITE = 0) Characteristic1 Symbol Min Max Unit fi D.C. 40.0 MHz tcyc 25 ns Pulse width, E high PWEH 11.5 -- ns D Pulse width, E low PWEL 11.5 -- ns 4 D Address delay time tAD -- 5 ns 5 D Address hold time tAH 0 -- ns No. C -- -- Frequency of internal bus 1 -- Cycle time 2 D 3 2 6 D IVDx delay time tIVDD -- 4.5 ns 7 D IVDx hold time2 tIVDH 0 -- ns 8 D Read data setup time (ITHRS = 1 only) Maskset M84E tDSR 15 -- ns D Read data setup time (ITHRS = 1 only) Maskset L15Y tDSR 12 -- ns 9 D Read data hold time tDHR 0 -- ns 10 D Write data delay time tDDW -- 5 ns 11 D Write data hold time tDHW 0 -- ns tRWD -1 5 ns 12 D 3 Read/write data delay time 1 Typical supply and silicon, room temperature only Includes also ACCx, IQSTATx 3 Includes LSTRB 2 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1285 Appendix A Electrical Characteristics A.8.4 Emulation Expanded Mode (With Optional Access Stretching) 1 2 3 ECLK2X ECLK 5 4 7 6 ADDR [22:20]/ ACC [2:0] ADDR1 ADDR [19:16]/ IQSTAT [3:0] ADDR1 ADDR [15:0]/ IVD [15:0] ADDR1 ACC1 IQSTAT0 ? ADDR1 ADDR1 ADDR1 000 IQSTAT1 ADDR2 ADDR2 IVD1 ADDR2 8 9 DATAx DATA0 (Read) DATA1 12 12 R/W LSTRB Figure A-15. Example 2b: Emulation Expanded Mode -- Read with 1 Stretch Cycle MC9S12XDP512 Data Sheet, Rev. 2.21 1286 Freescale Semiconductor Appendix A Electrical Characteristics 1 2 3 ECLK2X ECLK 4 5 7 6 ADDR [22:20]/ ACC [2:0] ADDR1 ACC1 ADDR1 ADDR [19:16]/ IQSTAT [3:0] ADDR1 IQSTAT0 ADDR1 ADDR [15:0]/ IVD [15:0] ADDR1 ? ADDR1 000 IQSTAT1 x ADDR2 ADDR2 ADDR2 10 DATAx 11 (write) data1 12 12 R/W LSTRB Figure A-16. Example 2b: Emulation Expanded Mode O Write with 1 Stretch Cycle MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1287 Appendix A Electrical Characteristics Table A-31. Example 2b: Emulation Expanded Mode Timing VDD35 = 5.0 V (EWAITE = 0) No. 1 C Characteristic Symbol 1 Stretch Cycle Min Max 2 Stretch Cycles Min Max 3 Stretch Cycles Min Max Unit -- -- Internal cycle time tcyc 25 25 25 25 25 25 ns 1 -- Cycle time tcyce 50 75 100 ns 2 D Pulse width, E high PWEH 11.5 14 11.5 14 11.5 14 ns 3 D E falling to sampling E rising tEFSR 35 39.5 60 64.5 85 89.5 ns 4 D Address delay time tAD -- 5 -- 5 -- 5 ns 5 D Address hold time tAH 0 -- 0 -- 0 -- ns 2 D IVD delay time tIVDD -- 4.5 -- 4.5 -- 4.5 ns 7 D 2 IVD hold time tIVDH 0 -- 0 -- 0 -- ns 8 D Read data setup time Maskset L15Y tDSR 12 -- 12 -- 12 -- ns D Read data setup time Maskset M84E tDSR 15 -- 15 -- 15 -- ns 9 D Read data hold time tDHR 0 -- 0 -- 0 -- ns 10 D Write data delay time tDDW -- 5 -- 5 -- 5 ns 11 D Write data hold time tDHW 0 -- 0 -- 0 -- ns 12 D Read/write data delay time3 tRWD -1 5 -1 5 -1 5 ns 6 1 Typical supply and silicon, room temperature only Includes also ACCx, IQSTATx 3 Includes LSTRB 2 MC9S12XDP512 Data Sheet, Rev. 2.21 1288 Freescale Semiconductor Appendix A Electrical Characteristics A.8.5 External Tag Trigger Timing 1 ECLK ADDR ADDR DATAx DATA R/W 2 TAGHI/TAGLO 3 Figure A-17. External Trigger Timing Table A-32. External Tag Trigger Timing VDD35 = 5.0 V 1 Characteristic 1 No. C 1 D Frequency of internal bus 2 D 3 4 Symbol Min Max Unit fi D.C. 40.0 MHz Cycle time tcyc 25 ns D TAGHI/TAGLO setup time tTS 11.5 -- ns D TAGHI/TAGLO hold time tTH 0 -- ns Typical supply and silicon, room temperature only MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1289 Appendix B Package Information Appendix B Package Information This section provides the physical dimensions of the MC9S12XD Family packages. MC9S12XDP512 Data Sheet, Rev. 2.21 1290 Freescale Semiconductor Appendix B Package Information B.1 144-Pin LQFP 0.20 T L-M N 4X PIN 1 IDENT 0.20 T L-M N 4X 36 TIPS 144 109 1 108 4X J1 P J1 L M CL B V X 140X B1 VIEW Y 36 V1 NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. DATUMS L, M, N TO BE DETERMINED AT THE SEATING PLANE, DATUM T. 4. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE, DATUM T. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE H. 6. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.35. 73 37 72 N A1 S1 A S VIEW AB C 0.1 T 2 144X SEATING PLANE 2 T PLATING J F AA C2 0.05 R2 R1 D 0.08 M 0.25 BASE METAL GAGE PLANE T L-M N SECTION J1-J1 (ROTATED 90 ) 144 PL (K) C1 E (Y) VIEW AB G VIEW Y MILLIMETERS DIM MIN MAX A 20.00 BSC A1 10.00 BSC B 20.00 BSC B1 10.00 BSC C 1.40 1.60 C1 0.05 0.15 C2 1.35 1.45 D 0.17 0.27 E 0.45 0.75 F 0.17 0.23 G 0.50 BSC J 0.09 0.20 K 0.50 REF P 0.25 BSC R1 0.13 0.20 R2 0.13 0.20 S 22.00 BSC S1 11.00 BSC V 22.00 BSC V1 11.00 BSC Y 0.25 REF Z 1.00 REF AA 0.09 0.16 0 1 0 7 2 11 13 1 (Z) Figure B-1. 144-Pin LQFP Mechanical Dimensions (Case No. 918-03) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1291 Appendix B Package Information B.2 112-Pin LQFP Package 0.20 T L-M N 4X PIN 1 IDENT 0.20 T L-M N 4X 28 TIPS 112 J1 85 4X P J1 1 CL 84 VIEW Y 108X X X=L, M OR N G VIEW Y B L V M B1 28 57 29 F D 56 0.13 N S1 A S C2 VIEW AB 2 0.050 0.10 T 112X SEATING PLANE 3 T R R2 R 0.25 R1 GAGE PLANE (K) C1 M BASE METAL T L-M N SECTION J1-J1 ROTATED 90 COUNTERCLOCKWISE A1 C AA J V1 E 1 (Y) (Z) VIEW AB NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS IN MILLIMETERS. 3. DATUMS L, M AND N TO BE DETERMINED AT SEATING PLANE, DATUM T. 4. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE, DATUM T. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE. DIMENSIONS A AND B INCLUDE MOLD MISMATCH. 6. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.46. DIM A A1 B B1 C C1 C2 D E F G J K P R1 R2 S S1 V V1 Y Z AA 1 2 3 MILLIMETERS MIN MAX 20.000 BSC 10.000 BSC 20.000 BSC 10.000 BSC --1.600 0.050 0.150 1.350 1.450 0.270 0.370 0.450 0.750 0.270 0.330 0.650 BSC 0.090 0.170 0.500 REF 0.325 BSC 0.100 0.200 0.100 0.200 22.000 BSC 11.000 BSC 22.000 BSC 11.000 BSC 0.250 REF 1.000 REF 0.090 0.160 8 0 7 3 13 11 11 13 Figure B-2. 112-Pin LQFP Mechanical Dimensions (Case No. 987) MC9S12XDP512 Data Sheet, Rev. 2.21 1292 Freescale Semiconductor Appendix B Package Information B.3 80-Pin QFP Package L 60 41 61 D S M V P B C A-B D 0.20 M B B -A-,-B-,-D- 0.20 L H A-B -B- 0.05 D -A- S S S 40 DETAIL A DETAIL A 21 80 1 0.20 A H A-B M S F 20 -DD S 0.05 A-B J S 0.20 C A-B M S D S D M E DETAIL C C -H- -C- DATUM PLANE 0.20 M C A-B S D S SECTION B-B VIEW ROTATED 90 0.10 H SEATING PLANE N M G U T DATUM PLANE -H- R K W Q NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS -A-, -B- AND -D- TO BE DETERMINED AT DATUM PLANE -H-. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE -C-. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -H-. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. X DETAIL C DIM A B C D E F G H J K L M N P Q R S T U V W X MILLIMETERS MIN MAX 13.90 14.10 13.90 14.10 2.15 2.45 0.22 0.38 2.00 2.40 0.22 0.33 0.65 BSC --0.25 0.13 0.23 0.65 0.95 12.35 REF 5 10 0.13 0.17 0.325 BSC 0 7 0.13 0.30 16.95 17.45 0.13 --0 --16.95 17.45 0.35 0.45 1.6 REF Figure B-3. 80-Pin QFP Mechanical Dimensions (Case No. 841B) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1293 Appendix C Recommended PCB Layout Appendix C Recommended PCB Layout The PCB must be carefully laid out to ensure proper operation of the voltage regulator as well as of the MCU itself. The following rules must be observed: * Every supply pair must be decoupled by a ceramic capacitor connected as near as possible to the corresponding pins (C1-C6). * Central point of the ground star should be the VSSR pin. * Use low ohmic low inductance connections between VSS1, VSS2, and VSSR. * VSSPLL must be directly connected to VSSR. * Keep traces of VSSPLL, EXTAL, and XTAL as short as possible and occupied board area for C7, C8, and Q1 as small as possible. * Do not place other signals or supplies underneath area occupied by C7, C8, and Q1 and the connection area to the MCU. * Central power input should be fed in at the VDDA/VSSA pins. MC9S12XDP512 Data Sheet, Rev. 2.21 1294 Freescale Semiconductor Appendix C Recommended PCB Layout Table C-1. Recommended Decoupling Capacitor Choice Component Purpose Type Value C1 VDD1 filter capacitor Ceramic 220 nF C2 VDD2 filter capacitor Ceramic X7R 220 nF C3 VDDA filter capacitor Ceramic X7R >=100 nF C4 VDDR filter capacitor X7R/tantalum >=100 nF C5 VDDPLL filter capacitor Ceramic X7R 220 nF C6 VDDX filter capacitor X7R/tantalum >=100 nF C7 OSC load capacitor C8 OSC load capacitor C9 PLL loop filter capacitor C10 PLL loop filter capacitor C11 VDDX filter capacitor X7R/tantalum >=100 nF C12 VDDX filter capacitor X7R/tantalum >=100 nF R1 PLL loop filter resistor Q1 Quartz Comes from crystal manufacturer See PLL specification chapter See PLL specification chapter -- -- MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1295 Appendix C Recommended PCB Layout C6 VDDX Figure C-1. 144-Pin LQFP Recommended PCB Layout VSSA VREGEN C3 VDDA VDD1 C1 VSS1 VSS2 C2 VDD2 VDDX2 VDDR2 C11 C12 VSSX2 VSSR2 C5 Q1 C7 VSSPLL C10 VDDPLL C9 C8 VDDR1 C4 VSSR1 R1 MC9S12XDP512 Data Sheet, Rev. 2.21 1296 Freescale Semiconductor Appendix C Recommended PCB Layout C6 VDDX Figure C-2. 112-Pin LQFP Recommended PCB Layout VSSA VREGEN VSSX C3 VDDA VDD1 C1 VSS1 VSS2 C2 VDD2 C5 C7 C10 C9 VDDPLL VSSPLL Q1 C8 VDDR C4 VSSR R1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1297 Appendix C Recommended PCB Layout VREGEN C6 VDDX Figure C-3. 80-Pin QFP Recommended PCB Layout VSSX VSSA C3 VDDA VDD1 VSS2 C1 C2 VSS1 C5 VSSPLL Q1 C8 VDDR C7 VSSR C4 VDD2 C10 C9 VSSPLL R1 VDDPLL MC9S12XDP512 Data Sheet, Rev. 2.21 1298 Freescale Semiconductor Appendix D Using L15Y Silicon Appendix D Using L15Y Silicon The following items should be considerd when using L15Y Silicon: * Do not write or read to registers which are marked "Reserved" in Table 1-1. * Fill the interrupt vector locations which are marked "Reserved" in Table 1-12. according to your coding policies for unused interrupts * L15Y Silicon includes two analog to digital converters ATD0 and ATD1. ATD0 channels 7 to 0 are connected to PAD07 to PAD00 and ATD1 channels 7 to 0 are connected to PAD15 to PAD08. * L15Y Silicon integrates the S12X_DBG module Version 2. L15Y Silicon integrates the S12X_MMC module Version 2. This Version doesn't support the following enhancement which is available on S12X_MMC Version 3: -- S12XCPU and S12XBDM can access MCU resources which are on different target busses at the same time. I.E S12XCPU can access XSRAM and S12XBDM can access Register Space at the same time. MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1299 Appendix E Derivative Differences Appendix E Derivative Differences E.1 Memory Sizes and Package Options S12XD - Family Table E-1. Memory Sizes and Package Options S12XD-Family Device Package Flash 144 LQFP RAM EEPROM ROM 32K 9S12XDP512 112 LQFP 144 LQFP 9S12XDT512 512K 112 LQFP 20K 80 QFP 144 LQFP 9S12XDT384 112 LQFP 384K 20K 80 QFP 144 LQFP 9S12XDQ256 4K 112 LQFP 80 QFP 16K 144 LQFP 9S12XDT256 112 LQFP 256K 80 QFP 144 LQFP 9S12XD256 112 LQFP 14K 80 QFP 144 LQFP 3S12XDT256 112 LQFP 16K 256K 80 QFP 112 LQFP 9S12XDG128 128K 2K 80 QFP 12K 112 LQFP 3S12XDG128 128K 80 QFP MC9S12XDP512 Data Sheet, Rev. 2.21 1300 Freescale Semiconductor Appendix E Derivative Differences Table E-1. Memory Sizes and Package Options S12XD-Family Device Package Flash RAM EEPROM 128K 8K 2K 64K 4K 1K ROM 112 LQFP 9S12XD128 80 QFP 9S12XD64 80 QFP MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1301 Appendix E Derivative Differences E.2 Memory Sizes and Package Options S12XA & S12XB Family Table E-2. S12XA - Family Memory Sizes Device Package Flash RAM 512K 32K EEPROM 144 LQFP 9S12XA512 112 LQFP 80 QFP 4K 144 LQFP 9S12XA256 112 LQFP 256K 16K 128K 12K 80 QFP 112 LQFP 9S12XA128 2K 80 QFP Table E-3. S12XB - Family Memory Sizes Device Package Flash RAM EEPROM 256K 10K 2K 128K 6K 1K 112 LQFP 9S12XB256 80 QFP 112 LQFP 9S12XB128 80 QFP MC9S12XDP512 Data Sheet, Rev. 2.21 1302 Freescale Semiconductor Appendix E Derivative Differences E.3 MC9S12XD-Family Flash Configuration1 2 3 4 5 Figure E-1. MC9S12XD Family Flash Configuration Global Address DP512 A512 DT384 DQ256 A/B256 128k 128k 128k DG128 A/B128 D64 $78_0000 (PPAGE $E0) $7A_0000 (PPAGE $E8) 128k $7C_0000 (PPAGE $F0) 128k 128k 128k 128k $7E_0000 (PPAGE $F8) 128k 128k 64k Shared XGATE/CPU area Not implemented 1. XGATE read access to Flash not possible on DG128/D128/A128/B128 and D64 2. Program Pages available on DT384 are $E0 - $E7 and $F0 - $FF 3. Program Pages available on B256/A256/DQ256/DT256/D256 are $E0 - $E7 and $F8 - $FF 4. Shared XGATE/CPU area on A512/DP512/DT512/DT384 at global address $78_0800 to $78_7FFF (30Kbyte) 5. Shared XGATE/CPU area on A256/B256/DT256/DQ256/D256 at global address $78_0800 to $78_7FFF (30Kbyte) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1303 Appendix E Derivative Differences E.4 MC9S12XD/A/B -Family SRAM & EEPROM Configuration Figure E-2. Available RAM Pages on S12XD-Family1 RAM Page RP[7:0] DP512 A512 DT512 DT384 DQ256 A256 DG128 A128 D128 D64 0xF6 0xF7 0xF8 0xF9 0xFA 0xFB 32K Byte 0xFC 0xFD 20K Byte 16K Byte 0xFE 12K Byte 8K Byte 0xFF 4K Byte 1 On 9S12XD256 14K byte RAM available pages FF,FE,FD and upper half of page FC On 9S12XB256 10K byte RAM available pages FF, FE upper half of page FD On 9S12XB218 6K byte RAM available pages FF and upper half of page FE Table E-4. Available EEPROM Pages on MC9S12XD-Family EEPROM Page EP[7:0] DP512 DT512 DT384 DQ256 A256 A512 DG128 D128 A128 B256 D64 B128 0xFA 0xFB 0xFC 0xFD 4K Byte 0xFE 2K Byte 0xFF 1K Byte MC9S12XDP512 Data Sheet, Rev. 2.21 1304 Freescale Semiconductor Appendix E Derivative Differences E.5 Peripheral Sets S12XD - Family Table E-5. S12XD Peripherals Device Package XGATE CAN SCI SPI IIC ECT PIT ATD0 ATD1 I/O 144LQFP 5 6 3 2 8 4 8ch1 16ch2 119 112LQFP 5 6 3 1 8 4 8ch1 8ch3 91 144LQFP 3 6 3 1 8 4 8ch1 16ch2 119 112LQFP 3 6 3 1 8 4 8ch1 8ch3 91 80QFP 3 2 3 1 8 4 8ch1 144LQFP 3 4 3 1 8 4 8ch1 16ch2 119 112LQFP 3 4 3 1 8 4 8ch1 8ch3 91 80QFP 3 2 3 1 8 4 8ch1 144LQFP 4 4 3 1 8 4 8ch1 16ch2 119 4 4 3 1 8 4 8ch1 8ch3 91 80QFP 4 2 3 1 8 4 8ch1 144LQFP 3 4 3 1 8 4 8ch1 16ch2 119 112LQFP 3 4 3 1 8 4 8ch1 8ch3 91 80QFP 3 2 3 1 8 4 8ch1 144LQFP 1 4 3 1 8 4 8ch1 16ch2 119 112LQFP 1 4 3 1 8 4 8ch1 8ch3 91 80QFP 1 2 3 1 8 4 8ch1 144LQFP 3 4 3 1 8 4 8ch1 16ch2 119 112LQFP 3 4 3 1 8 4 8ch1 8ch3 91 80QFP 3 2 3 1 8 4 8ch1 112LQFP 2 2 2 1 8 4 16ch4 91 80QFP 2 2 2 1 8 4 8ch5 59 2 2 2 1 8 4 16ch4 91 2 2 2 1 8 4 8ch5 59 1 2 2 1 8 4 16ch4 91 80QFP 1 2 2 1 8 4 8ch5 59 80QFP 1 2 2 1 8 2 8ch5 59 9S12XDP512 9S12XDT512 9S12XDT384 9S12XDQ256 112LQFP yes 9S12XDT256 9S12XD256 3S12XDT256 9S12XDG128 112LQFP 3S12XDG128 80QFP 112LQFP 9S12XD128 9S12XD64 1 yes but XGATE has no Flash Access 59 59 59 59 59 59 ATD0 routed to PAD[7:0] MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1305 Appendix E Derivative Differences 2 ATD1 routed to PAD[23:8] ATD1 routed to PAD[15:8] 4 ATD1 routed to PAD[15:0] instead of PAD[23:8] 5 ATD1 routed to PAD[7:0] instead of PAD[15:8] 3 E.6 Peripheral Sets S12XA & S12XB - Family Table E-6. S12XA Peripherals Device 9S12XA512 Package XGATE CAN SCI SPI IIC ECT PIT ATD0 ATD1 I/O 144LQFP 6 3 1 8 4 8ch1 16ch2 119 112LQFP 4 3 1 8 4 8ch1 8ch3 91 80QFP 2 2 1 8 4 8ch1 4 3 1 8 4 8ch1 16ch2 119 112LQFP 4 3 1 8 4 8ch1 8ch3 91 80QFP 2 2 1 8 4 8ch1 2 2 1 8 2 16ch5 91 2 2 1 8 2 8ch6 59 yes 144LQFP no 9S12XA256 112LQFP 9S12XA128 80QFP 1 2 3 4 5 6 yes4 59 59 ATD0 routed to PAD[7:0] ATD1 routed to PAD[23:8] ATD1 routed to PAD[15:8] Can execute code only from RAM ATD1 routed to PAD[15:0] instead of PAD[23:8] ATD1 routed to PAD[7:0] instead of PAD[15:8] Table E-7. S12XB Peripherals Device Package XGATE 112LQFP 9S12XB256 CAN SCI SPI IIC ECT PIT ATD0 ATD1 1 2 1 1 8 4 8ch1 8ch2 1 2 1 1 8 4 8ch2 1 2 1 1 8 2 16ch4 2 1 1 8 2 8ch5 yes 80QFP 112LQFP 9S12XB128 80QFP yes3 1 ATD0 routed to PAD[7:0] ATD1 routed to PAD[15:8] 3 Can execute code only from RAM 4 ATD1 routed to PAD[15:0] instead of PAD[23:8] 5 ATD1 routed to PAD[7:0] imstead of PAD[15:8] 2 MC9S12XDP512 Data Sheet, Rev. 2.21 1306 Freescale Semiconductor Appendix E Derivative Differences E.7 Pinout explanations: * A/D is the number of modules/total number of A/D channels. * I/O is the sum of ports capable to act as digital input or output. - 144 Pin Packages: Port A = 8, B = 8, C=8, D=8, E = 6 + 2 input only, H = 8, J = 7, K = 8, M = 8, P = 8, S = 8, T = 8, PAD = 24 25 inputs provide Interrupt capability (H =8, P= 8, J = 7, IRQ, XIRQ) - 112 Pin Packages: Port A = 8, B = 8, E = 6 + 2 input only, H = 8, J = 4, K = 7, M = 8, P = 8, S = 8, T = 8, PAD = 16 22 inputs provide Interrupt capability (H =8, P= 8, J = 4, IRQ, XIRQ) - 80 Pin Packages: Port A = 8, B = 8, E = 6 + 2 input only, J = 2, M = 6, P = 7, S = 4, T = 8, PAD = 8 11 inputs provide Interrupt capability (P= 7, J = 2, IRQ, XIRQ) * CAN0 can be routed under software control from PM[1:0] to pins PM[3:2] or PM[5:4] or PJ[7:6]. * CAN4 pins are shared between IIC0 pins. * CAN4 can be routed under software control from PJ[7:6] to pins PM[5:4] or PM[7:6]. * Versions with 4 CAN modules will have CAN0, CAN1, CAN2 and CAN4 * Versions with 3 CAN modules will have CAN0, CAN1 and CAN4. * Versions with 2 CAN modules will have CAN0 and CAN4. * Versions with 1 CAN modules will have CAN0 * Versions with 2 SPI modules will have SPI0 and SPI1. * Versions with 4 SCI modules will have SCI0, SCI1, SCI2 and SCI4. * Versions with 2 SCI modules will have SCI0 and SCI1. * Versions with 1 IIC module will have IIC0. * SPI0 can be routed to either Ports PS[7:4] or PM[5:2]. * SPI1 pins are shared with PWM[3:0]; In 144 and 112-pin versions, SPI1 can be routed under software control to PH[3:0]. * SPI2 pins are shared with PWM[7:4]; In 144 and 112-pin versions, SPI2 can be routed under software control to PH[7:4]. In 80-pin packages, SS-signal of SPI2 is not bonded out! MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1307 Appendix F Ordering Information Appendix F Ordering Information The following figure provides an ordering number example for the devices covered by this data book. There are two options when ordering a device. Customers must choose between ordering either the mask-specific partnumber or the generic / mask-independent partnumber Ordering the mask-specific partnumber enables the customer to specify which particular maskset they will receive whereas FSL will ship the currently preferred maskset against any orders for the generic partnumber. In either case, the marking on the device will always show the generic / mask-independent partnumber and the mask set number. For specific partnumbers, please contact your local sales office. The below figure illustrates a mask-specific ordering number. Part numbers may be abbreviated: check with manufacturer for exact part number S 9 12XDP512 J1 M AL R Tape & Reel Suffix (Optional): No R = No Tape & Reel R = Tape & Reel Part name (abbreviated) see Table 1-6 Package Option FU = 80QFP (non lead -free) PV = 112LQFP (non lead -free) FV = 144LQFP (non lead -free) AA = 80QFP (lead free) AL=112LQFP (lead free) AG = 144LQFP (Lead free) Main Memory Type 9=Flash 3=ROM Temperature Option C = -40 to 85 C V = -40 to 105 C M = -40 to 125 C Status / Partnumber type S or SC = Maskset specific partnumber MC = Generic/mask independent partnumber P or PC = Prototype status Maskset identifier suffix (two digits): First digit references wafer fab Second digit differentiates mask This suffix is omitted in generic partnumbers J1 = 1L15Y maskset in this case F0 = 0M42E maskset in this case MC9S12XDP512 Data Sheet, Rev. 2.21 1308 Freescale Semiconductor Appendix G Detailed Register Map Appendix G Detailed Register Map The following tables show the detailed register map of the MC9S12XD-Family. 0x0000-0x0009 Port Integration Module (PIM) Map 1 of 5 Address Name 0x0000 PORTA 0x0001 PORTB 0x0002 DDRA 0x0003 DDRB 0x0004 PORTC 0x0005 PORTD 0x0006 DDRC 0x0007 DDRD 0x0008 PORTE 0x0009 DDRE R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA 0 PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 DDRA7 DDRA6 DDRA5 DDRA4 DDRA3 DDRA2 DDRA1 DDRA0 DDRB7 DDRB6 DDRB5 DDRB4 DDRB3 DDRB2 DDRB1 DDRB0 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 DDRC7 DDRC6 DDRC5 DDRC4 DDRC3 DDRC2 DDRC1 DDRC0 DDRD7 DDRD6 DDRD5 DDRD4 DDRD3 DDRD2 DDRD1 DDRD0 PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 DDRE7 DDRE6 DDRE5 DDRE4 DDRE3 DDRE2 0 0 Bit 2 Bit 1 Bit 0 CS2E CS1E CS0E 0x000A-0x000B Module Mapping Control (S12XMMC) Map 1 of 4 Address Name 0x000A MMCCTL0 0x000B MODE R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 0 0 0 0 0 MODC MODB MODA 0 0 0 0 0 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PUPEE PUPDE PUPCE PUPBE PUPAE RDPE RDPD RDPC RDPB RDPA 0x000C-0x000D Port Integration Module (PIM) Map 2 of 5 Address Name 0x000C PUCR 0x000D RDRIV Bit 7 R W R W PUPKE RDPK Bit 6 BKPUE 0 Bit 5 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1309 Appendix G Detailed Register Map 0x000E-0x000F External Bus Interface (S12XEBI) Map Address Name 0x000E EBICTL0 0x000F EBICTL1 Bit 7 R ITHRS W R EWAITE W Bit 6 0 0 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 HDBE ASIZ4 ASIZ3 ASIZ2 ASIZ1 ASIZ0 0 0 0 EXSTR2 EXSTR1 EXSTR0 0x0010-0x0017 Module Mapping Control (S12XMMC) Map 2 of 4 Address Name 0x0010 GPAGE 0x0011 DIRECT 0x0012 Reserved 0x0013 MMCCTL1 0x0014 Reserved 0x0015 Reserved 0x0016 RPAGE 0x0017 EPAGE Bit 7 R W R W R W R W R W R W R W R W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 GP6 GP5 GP4 GP3 GP2 GP1 GP0 DP15 DP14 DP13 DP12 DP11 DP10 DP9 DP8 0 0 0 0 0 0 0 0 0 0 0 0 0 EROMON ROMHM ROMON 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RP7 RP6 RP5 RP4 RP3 RP2 RP1 RP0 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 0 0x0018-0x001B Miscellaneous Peripheral Address Name 0x0018 Reserved 0x0019 Reserved 0x001A PARTIDH 0x001B PARTIDL R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 Bit 1 Bit 0 EDIV1 EDIV0 0x001C-0x001F Port Integration Module (PIM) Map 3 of 5 Address 0x001C Name ECLKCTL Bit 7 R W NECLK Bit 6 NCLKX2 Bit 5 Bit 4 Bit 3 Bit 2 0 0 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 1310 Freescale Semiconductor Appendix G Detailed Register Map 0x001C-0x001F Port Integration Module (PIM) Map 3 of 5 Address Name 0x001D Reserved 0x001E IRQCR 0x001F Reserved R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 IRQE IRQEN 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 XGSBPE BDM 0 0 0x0020-0x0027 Debug Module (S12XDBG) Map Address Name 0x0020 DBGC1 0x0021 DBGSR 0x0022 DBGTCR 0x0023 DBGC2 0x0024 DBGTBH 0x0025 DBGTBL 0x0026 DBGCNT 0x0027 DBGSCRX 0x00281 DBGXCTL (COMPA/C) 0x00282 DBGXCTL (COMPB/D) 0x0029 DBGXAH 0x002A DBGXAM 0x002B DBGXAL 0x002C DBGXDH 0x002D DBGXDL 0x002E DBGXDHM 0x002F DBGXDLM 1 Bit 7 R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W ARM TBF Bit 6 0 TRIG EXTF TSOURCE DBGBRK 0 TRANGE COMRV SSF2 SSF1 SSF0 TRCMOD TALIGN CDCM ABCM 0 0 0 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SC3 SC2 SC1 SC0 0 0 CNT 0 0 0 NDB TAG BRK RW RWE SRC COMPE SZ TAG BRK RW RWE SRC COMPE Bit 22 21 20 19 18 17 Bit 16 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 0 SZE 0 This represents the contents if the Comparator A or C control register is blended into this address MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1311 Appendix G Detailed Register Map 2 This represents the contents if the Comparator B or D control register is blended into this address MC9S12XDP512 Data Sheet, Rev. 2.21 1312 Freescale Semiconductor Appendix G Detailed Register Map 0x0030-0x0031 Module Mapping Control (S12XMMC) Map 3 of 4 Address Name 0x0030 PPAGE 0x0031 Reserved R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PIX7 PIX6 PIX5 PIX4 PIX3 PIX2 PIX1 PIX0 0 0 0 0 0 0 0 0 0x0032-0x0033 Port Integration Module (PIM) Map 4 of 5 Address Name 0x0032 PORTK 0x0033 DDRK R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PK7 PK6 PK5 PK4 PK3 PK2 PK1 PK0 DDRK7 DDRK6 DDRK5 DDRK4 DDRK3 DDRK2 DDRK1 DDRK0 0x0034-0x003F Clock and Reset Generator (CRG) Map Address Name 0x0034 SYNR 0x0035 REFDV 0x0036 CTFLG 0x0037 CRGFLG 0x0038 CRGINT 0x0039 CLKSEL 0x003A PLLCTL 0x003B RTICTL 0x003C COPCTL 0x003D FORBYP 0x003E CTCTL 0x003F ARMCOP Bit 7 R 0 W 0 R W R 0 W R RTIF W R RTIE W R PLLSEL W R CME W R RTDEC W R WCOP W R 0 W R 0 W R 0 W Bit 7 Bit 6 0 0 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SYN5 SYN4 SYN3 SYN2 SYN1 SYN0 REFDV5 REFDV4 REFDV3 REFDV2 REFDV1 REFDV0 0 0 0 0 PORF LVRF ILAF 0 0 0 0 Reserved For Factory Test LOCK TRACK LOCKIF LOCKIE 0 0 0 PLLON AUTO ACQ FSTWKP RTR6 RTR5 RTR4 RTR3 0 0 0 PSTP RSBCK 0 0 0 0 0 6 0 5 PLLWAI 0 0 Reserved For Factory Test 0 Reserved For Factory Test 0 0 4 3 0 0 SCMIF SCMIE SCM 0 RTIWAI COPWAI PRE PCE SCME RTR2 RTR1 RTR0 CR2 CR1 CR0 0 0 0 0 0 0 0 2 0 1 0 Bit 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1313 Appendix G Detailed Register Map 0x0040-0x007F Enhanced Capture Timer 16-Bit 8-Channels (ECT) Map (Sheet 1 of 3) Address Name 0x0040 TIOS 0x0041 CFORC 0x0042 OC7M 0x0043 OC7D 0x0044 TCNT (hi) 0x0045 TCNT (lo) 0x0046 TSCR1 0x0047 TTOV 0x0048 TCTL1 0x0049 TCTL2 0x004A TCTL3 0x004B TCTL4 0x004C TIE 0x004D TSCR2 0x004E TFLG1 0x004F TFLG2 0x0050 TC0 (hi) 0x0051 TC0 (lo) 0x0052 TC1 (hi) 0x0053 TC1 (lo) 0x0054 TC2 (hi) 0x0055 TC2 (lo) R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 IOS7 IOS6 IOS5 IOS4 IOS3 IOS2 IOS1 IOS0 0 FOC7 0 FOC6 0 FOC5 0 FOC4 0 FOC3 0 FOC2 0 FOC1 0 FOC0 OC7M7 OC7M6 OC7M5 OC7M4 OC7M3 OC7M2 OC7M1 OC7M0 OC7D7 OC7D6 OC7D5 OC7D4 OC7D3 OC7D2 OC7D1 OC7D0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 TEN TSWAI TSFRZ TFFCA PRNT 0 0 0 TOV7 TOV6 TOV5 TOV4 TOV3 TOV2 TOV1 TOV0 OM7 OL7 OM6 OL6 OM5 OL5 OM4 OL4 OM3 OL3 OM2 OL2 OM1 OL1 OM0 OL0 EDG7B EDG7A EDG6B EDG6A EDG5B EDG5A EDG4B EDG4A EDG3B EDG3A EDG2B EDG2A EDG1B EDG1A EDG0B EDG0A C7I C6I C5I C4I C3I C2I C1I C0I 0 0 0 TCRE PR2 PR1 PR0 C6F C5F C4F C3F C2F C1F C0F 0 0 0 0 0 0 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 Bit 15 14 13 12 11 10 9 Bit 8 Bit 7 6 5 4 3 2 1 Bit 0 TOI C7F TOF MC9S12XDP512 Data Sheet, Rev. 2.21 1314 Freescale Semiconductor Appendix G Detailed Register Map 0x0040-0x007F Enhanced Capture Timer 16-Bit 8-Channels (ECT) Map (Sheet 2 of 3) Address Name 0x0056 TC3 (hi) 0x0057 TC3 (lo) 0x0058 TC4 (hi) 0x0059 TC4 (lo) 0x005A TC5 (hi) 0x005B TC5 (lo) 0x005C TC6 (hi) 0x005D TC6 (lo) 0x005E TC7 (hi) 0x005F TC7 (lo) 0x0060 PACTL 0x0061 PAFLG 0x0062 PACN3 (hi) 0x0063 PACN2 (lo) 0x0064 PACN1 (hi) 0x0065 PACN0 (lo) 0x0066 MCCTL 0x0067 MCFLG 0x0068 ICPAR 0x0069 DLYCT 0x006A ICOVW 0x006B ICSYS 0x006C Reserved Bit 7 R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W R 0 W R 0 W R Bit 7 W R Bit 7 W R Bit 7 W R Bit 7 W R MCZI W R MCZF W R 0 W R DLY7 W R NOVW7 W R SH37 W R 0 W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 PAEN PAMOD PEDGE CLK1 CLK0 PAOVI PAI 0 0 0 0 0 PAOVF PAIF 6 5 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 MODMC RDMCL MCPR1 MCPR0 0 0 FLMC POLF3 MCEN 0 0 ICLAT 0 POLF2 POLF1 POLF0 0 0 0 PA3EN PA2EN PA1EN PA0EN DLY6 DLY5 DLY4 DLY3 DLY2 DLY1 DLY0 NOVW6 NOVW5 NOVW4 NOVW3 NOVW2 NOVW1 NOVW0 SH26 SH15 SH04 TFMOD PACMX BUFEN LATQ 0 0 0 0 0 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1315 Appendix G Detailed Register Map 0x0040-0x007F Enhanced Capture Timer 16-Bit 8-Channels (ECT) Map (Sheet 3 of 3) Address Name 0x006D TIMTST 0x006E PTPSR 0x006F PTMCPSR 0x0070 PBCTL 0x0071 PBFLG 0x0072 PA3H 0x0073 PA2H 0x0074 PA1H 0x0075 PA0H 0x0076 MCCNT (hi) 0x0077 MCCNT (lo) 0x0078 TC0H (hi) 0x0079 TC0H (lo) 0x007A TC1H (hi) 0x007B TC1H (lo) 0x007C TC2H (hi) 0x007D TC2H (lo) 0x007E TC3H (hi) 0x007F TC3H (lo) Bit 7 R 0 W R PTPS7 W R PTMPS7 W R 0 W R 0 W R PA3H7 W R PA2H7 W R PA1H7 W R PA0H7 W R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W R Bit 15 W R Bit 7 W Bit 6 Bit 5 0 0 Bit 2 Bit 1 Bit 0 0 0 0 PTPS6 PTPS5 PTPS4 PTPS3 PTPS2 PTPS1 PTPS0 PTMPS6 PTMPS5 PTMPS4 PTMPS3 PTMPS2 PTMPS1 PTMPS0 0 0 0 0 0 0 0 0 0 PA3H6 PA3H5 PA3H4 PA3H3 PA3H2 PA3H1 PA3H0 PA2H6 PA2H5 PA2H4 PA2H3 PA2H2 PA2H1 PA2H0 PA1H6 PA1H5 PA1H4 PA1H3 PA1H2 PA1H1 PA1H 0 PA0H6 PA0H5 PA0H4 PA0H3 PA0H2 PA0H1 PA0H0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 14 13 12 11 10 9 Bit 8 6 5 4 3 2 1 Bit 0 PBEN Bit 4 Bit 3 0 0 Reserved For Factory Test PBOVI PBOVF 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 1316 Freescale Semiconductor Appendix G Detailed Register Map 0x0080-0x00AF Analog-to-Digital Converter 10-bit 16-Channels (ATD1) Map (Sheet 1 of 3) Address Name 0x0080 ATD1CTL0 0x0081 ATD1CTL1 0x0082 ATD1CTL2 0x0083 ATD1CTL3 0x0084 ATD1CTL4 0x0085 ATD1CTL5 0x0086 ATD1STAT0 0x0087 Reserved 0x0088 ATD1TEST0 0x0089 ATD1TEST1 0x008A ATD1STAT2 0x008B ATD1STAT1 0x008C ATD1DIEN0 0x008D ATD1DIEN 0x008E ATD1PTAD0 0x008F ATD1PTAD1 0x0090 ATD1DR0H 0x0091 ATD1DR0L 0x0092 ATD1DR1H 0x0093 ATD1DR1L 0x0094 ATD1DR2H 0x0095 ATD1DR2L R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 0 0 0 0 Bit 3 Bit 2 Bit 1 Bit 0 WRAP3 WRAP2 WRAP1 WRAP0 ETRIG SEL 0 0 0 ETRIG CH3 ETRIG CH2 ETRIG CH1 ETRIG CH0 ADPU AFFC AWAI ETRIGLE ETRIGP ETRIGE ASCIE S8C S4C S2C S1C FIFO FRZ1 FRZ0 SRES8 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0 DJM DSGN SCAN MULT CD CC CB CA ETORF FIFOR CC3 CC2 CC1 CC0 0 0 0 0 0 U U U U U 0 SCF 0 ASCIF 0 0 0 U U U U U U CCF14 CCF13 CCF12 CCF11 CCF10 CCF9 CCF8 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0 IEN14 IEN13 IEN12 IEN11 IEN10 IEN9 IEN8 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0 PTAD14 PTAD13 PTAD12 PTAD11 PTAD10 PTAD9 PTAD8 PTAD6 PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 14 13 12 11 10 9 Bit8 Bit6 0 0 0 0 0 0 14 13 12 11 10 9 Bit8 Bit6 0 0 0 0 0 0 14 13 12 11 10 9 Bit8 Bit6 0 0 0 0 0 0 R CCF15 W R CCF7 W R IEN15 W R IEN7 W R PTAD15 W R PTAD7 W R Bit15 W R Bit7 W R Bit15 W R Bit7 W R Bit15 W R Bit7 W U U Reserved For Factory Test U U SC MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1317 Appendix G Detailed Register Map 0x0080-0x00AF Analog-to-Digital Converter 10-bit 16-Channels (ATD1) Map (Sheet 2 of 3) Address Name 0x0096 ATD1DR3H 0x0097 ATD1DR3L 0x0098 ATD1DR4H 0x0099 ATD1DR4L 0x009A ATD1DR5H 0x009B ATD1DR5L 0x009C ATD1DR6H 0x009D ATD1DR6L 0x009E ATD1DR7H 0x009F ATD1DR7L 0x00A0 ATD1DR8H 0x00A1 ATD1DR8L 0x00A2 ATD1DR9H 0x00A3 ATD1DR9L 0x00A4 ATD1DR10H 0x00A5 ATD1DR10L 0x00A6 ATD1DR11H 0x00A7 ATD1DR11L 0x00A8 ATD1DR12H 0x00A9 ATD1DR12L 0x00AA ATD1DR13H 0x00AB ATD1DR13L R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 1318 Freescale Semiconductor Appendix G Detailed Register Map 0x0080-0x00AF Analog-to-Digital Converter 10-bit 16-Channels (ATD1) Map (Sheet 3 of 3) Address Name 0x00AC ATD1DR14H 0x00AD 0x00AE 0x00AF R W R ATD1DR14L W R ATD1DR15H W R ATD1DR15L W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit 0 0x00B0-0x00B7 Inter IC Bus (IIC1) Map Address Name 0x00B0 IBAD 0x00B1 IBFD 0x00B2 IBCR 0x00B3 IBSR 0x00B4 IBDR 0x00B5 Reserved 0x00B6 Reserved 0x00B7 Reserved R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 IBC7 IBC6 IBC5 IBC4 IBC3 IBC2 IBC1 IBEN IBIE MS/SL TX/RX TXAK 0 TCF IAAS IBB 0 0 RSTA SRW D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 IBAL IBIF 0 IBC0 IBSWAI RXAK 0x00B8-0x00BF Asynchronous Serial Interface (SCI2) Map Address Name 0x00B8 SCI2BDH1 0x00B9 SCI2BDL1 0x00BA SCI2CR11 0x00B8 SCI2ASR12 0x00B9 SCI2ACR12 0x00BA SCI2ACR22 Bit 7 R IREN W R SBR7 W R LOOPS W R RXEDGIF W R RXEDGIE W R 0 W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 BERRV BERRIF BKDIF 0 0 0 0 BERRIE BKDIE 0 0 0 0 BERRM0 BKDFE 0 BERRM1 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1319 Appendix G Detailed Register Map 0x00B8-0x00BF Asynchronous Serial Interface (SCI2) Map (continued) Address Name 0x00BB SCI2CR2 0x00BC SCI2SR1 0x00BD SCI2SR2 0x00BE SCI2DRH 0x00BF SCI2DRL 1 2 R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TIE TCIE RIE ILIE TE RE RWU SBK TDRE TC RDRF IDLE OR NF FE PF 0 0 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 0 R5 T5 R4 T4 R3 T3 R2 T2 R1 T1 R0 T0 AMAP R8 R7 T7 T8 R6 T6 RAF Those registers are accessible if the AMAP bit in the SCI2SR2 register is set to zero Those registers are accessible if the AMAP bit in the SCI2SR2 register is set to one 0x00C0-0x00C7 Asynchronous Serial Interface (SCI3) Map Address 1 2 Name 0x00C0 SCI3BDH1 0x00C1 SCI3BDL1 0x00C2 SCI3CR11 0x00C0 SCI3ASR12 0x00C1 SCI3ACR12 0x00C2 SCI3ACR22 0x00C3 SCI3CR2 0x00C4 SCI3SR1 0x00C5 SCI3SR2 0x00C6 SCI3DRH 0x00C7 SCI3DRL Bit 7 R IREN W R SBR7 W R LOOPS W R RXEDGIF W R RXEDGIE W R 0 W R TIE W R TDRE W R AMAP W R R8 W R R7 W T7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 BERRV BERRIF BKDIF 0 0 0 0 BERRIE BKDIE 0 0 0 0 BERRM1 BERRM0 BKDFE TCIE RIE ILIE TE RE RWU SBK TC RDRF IDLE OR NF FE PF 0 0 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 0 R5 T5 R4 T4 R3 T3 R2 T2 R1 T1 R0 T0 T8 R6 T6 0 RAF Those registers are accessible if the AMAP bit in the SCI3SR2 register is set to zero Those registers are accessible if the AMAP bit in the SCI3SR2 register is set to one MC9S12XDP512 Data Sheet, Rev. 2.21 1320 Freescale Semiconductor Appendix G Detailed Register Map 0x00C8-0x00CF Asynchronous Serial Interface (SCI0) Map Address Name 0x00C8 SCI0BDH1 0x00C9 SCI0BDL1 0x00CA SCI0CR11 0x00C8 SCI0ASR12 0x00C9 SCI0ACR12 0x00CA SCI0ACR22 0x00CB SCI0CR2 0x00CC SCI0SR1 0x00CD SCI0SR2 0x00CE SCI0DRH 0x00CF SCI0DRL 1 2 Bit 7 R IREN W R SBR7 W R LOOPS W R RXEDGIF W R RXEDGIE W R 0 W R TIE W R TDRE W R AMAP W R R8 W R R7 W T7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 BERRV BERRIF BKDIF 0 0 0 0 BERRIE BKDIE 0 0 0 0 BERRM1 BERRM0 BKDFE TCIE RIE ILIE TE RE RWU SBK TC RDRF IDLE OR NF FE PF 0 0 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 0 R5 T5 R4 T4 R3 T3 R2 T2 R1 T1 R0 T0 T8 R6 T6 0 RAF Those registers are accessible if the AMAP bit in the SCI0SR2 register is set to zero Those registers are accessible if the AMAP bit in the SCI0SR2 register is set to one 0x00D0-0x00D7 Asynchronous Serial Interface (SCI1) Map Address Name 0x00D0 SCI1BDH1 0x00D1 SCI1BDL1 0x00D2 SCI1CR11 0x00D0 SCI1ASR12 0x00D1 SCI1ACR12 0x00D2 SCI1ACR22 0x00D3 SCI1CR2 0x00D4 SCI1SR1 Bit 7 R IREN W R SBR7 W R LOOPS W R RXEDGIF W R RXEDGIE W R 0 W R TIE W R TDRE W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 BERRV BERRIF BKDIF 0 0 0 0 BERRIE BKDIE 0 0 0 0 BERRM1 BERRM0 BKDFE TCIE RIE ILIE TE RE RWU SBK TC RDRF IDLE OR NF FE PF 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1321 Appendix G Detailed Register Map 0x00D0-0x00D7 Asynchronous Serial Interface (SCI1) Map (continued) Address 1 2 Name 0x00D5 SCI1SR2 0x00D6 SCI1DRH 0x00D7 SCI1DRL Bit 7 R W R W R W AMAP R8 R7 T7 Bit 6 Bit 5 0 0 T8 R6 T6 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 0 R5 T5 R4 T4 R3 T3 R2 T2 R1 T1 R0 T0 RAF Those registers are accessible if the AMAP bit in the SCI1SR2 register is set to zero Those registers are accessible if the AMAP bit in the SCI1SR2 register is set to one 0x00D8-0x00DF Serial Peripheral Interface (SPI0) Map Address Name 0x00D8 SPI0CR1 0x00D9 SPI0CR2 0x00DA SPI0BR 0x00DB SPI0SR 0x00DC Reserved 0x00DD SPI0DR 0x00DE Reserved 0x00DF Reserved R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0 0 0 MODFEN BIDIROE SPISWAI SPC0 SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 SPIF 0 SPTEF MODF 0 0 0 0 0 0 0 0 0 0 0 0 Bit7 6 5 4 3 2 1 Bit0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 0 0 0 0 0x00E0-0x00E7 Inter IC Bus (IIC0) Map Address Name 0x00E0 IBAD 0x00E1 IBFD 0x00E2 IBCR 0x00E3 IBSR 0x00E4 IBDR R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 IBC7 IBC6 IBC5 IBC4 IBC3 IBC2 IBC1 IBEN IBIE MS/SL TX/RX TXAK 0 TCF IAAS IBB 0 0 RSTA SRW D7 D6 D5 D3 D2 IBAL D4 IBIF D1 0 IBC0 IBSWAI RXAK D0 MC9S12XDP512 Data Sheet, Rev. 2.21 1322 Freescale Semiconductor Appendix G Detailed Register Map 0x00E0-0x00E7 Inter IC Bus (IIC0) Map (continued) Address Name 0x00E5 Reserved 0x00E6 Reserved 0x00E7 Reserved R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0x00E8-0x00EF Reserved Address Name 0x00E8 Reserved 0x00E9 Reserved 0x00EA Reserved 0x00EB Reserved 0x00EC Reserved 0x00ED Reserved 0x00EE Reserved 0x00EF Reserved R W R W R W R W R W R W R W R W 0x00F0-0x00F7 Serial Peripheral Interface (SPI1) Map Address Name 0x00F0 SPI1CR1 0x00F1 SPI1CR2 0x00F2 SPI1BR 0x00F3 SPI1SR 0x00F4 Reserved 0x00F5 SPI1DR 0x00F6 Reserved 0x00F7 Reserved R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0 0 0 MODFEN BIDIROE SPISWAI SPC0 SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 SPIF 0 SPTEF MODF 0 0 0 0 0 0 0 0 0 0 0 0 Bit7 6 5 4 3 2 1 Bit0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1323 Appendix G Detailed Register Map 0x00F8-0x00FF Serial Peripheral Interface (SPI2) Map Address Name 0x00F8 SPI2CR1 0x00F9 SPI2CR2 0x00FA SPI2BR 0x00FB SPI2SR 0x00FC Reserved 0x00FD SPI2DR 0x00FE Reserved 0x00FF Reserved R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0 0 0 MODFEN BIDIROE SPISWAI SPC0 SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 SPIF 0 SPTEF MODF 0 0 0 0 0 0 0 0 0 0 0 0 Bit7 6 5 4 3 2 1 Bit0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0x0100-0x010F Flash Control Register (FTX512K4) Map Address Name 0x0100 FCLKDIV 0x0101 FSEC 0x0102 FTSTMOD 0x0103 FCNFG 0x0104 FPROT 0x0105 FSTAT 0x0106 FCMD 0x0107 FCTL 0x0108 FADDRHI 0x0109 FADDRLO 0x010A FDATAHI 0x010B FDATALO Bit 7 R FDIVLD W R KEYEN1 W R 0 W R CBEIE W R FPOPEN W R CBEIF W R 0 W R NV7 W R W R W R W R W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PRDIV8 FDIV5 FDIV4 FDIV3 FDIV2 FDIV1 FDIV0 KEYEN0 RNV5 RNV4 RNV3 RNV2 SEC1 SEC0 0 0 0 0 0 0 0 0 0 FPHDIS FPHS1 FPHS0 FPLDIS FPLS1 FPLS0 PVIOL ACCERR 0 BLANK 0 0 NV2 NV1 NV0 MRDS CCIE RNV6 CCIF WRALL KEYACC CMDB[6:0] NV6 NV5 NV4 NV3 FADDRHI FADDRLO FDATAHI FDATALO MC9S12XDP512 Data Sheet, Rev. 2.21 1324 Freescale Semiconductor Appendix G Detailed Register Map 0x0100-0x010F Flash Control Register (FTX512K4) Map (continued) Address Name 0x010C Reserved 0x010D Reserved 0x010E Reserved 0x010F Reserved R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0x0110-0x011B EEPROM Control Register (EETX4K) Map Address Name 0x0110 ECLKDIV 0x0111 Reserved 0x0112 Reserved 0x0113 ECNFG 0x0114 EPROT 0x0115 ESTAT 0x0116 ECMD 0x0117 Reserved 0x0118 EADDRHI 0x0119 EADDRLO 0x011A EDATAHI 0x011B EDATALO Bit 7 R EDIVLD W R 0 W R 0 W R CBEIE W R EPOPEN W R CBEIF W R 0 W R 0 W R 0 W R W R W R W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PRDIV8 EDIV5 EDIV4 EDIV3 EDIV2 EDIV1 EDIV0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 RNV5 RNV4 EPDIS EPS2 EPS1 EPS0 PVIOL ACCERR 0 BLANK 0 0 0 0 0 CCIE RNV6 CCIF CMDB[6:0] 0 0 0 0 0 0 0 0 EABHI EABLO EDHI EDLO MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1325 Appendix G Detailed Register Map 0x011C-0x011F Memory Map Control (S12XMMC) Map 4 of 4 Address Name 0x011C RAMWPC 0x011D RAMXGU 0x011E RAMSHL 0x011F RAMSHU Bit 7 R W R W R W R W RPWE 1 1 1 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 AVIE AVIF XGU6 XGU5 XGU4 XGU3 XGU2 XGU1 XGU0 SHL6 SHL5 SHL4 SHL3 SHL2 SHL1 SHL0 SHU6 SHU5 SHU4 SHU3 SHU2 SHU1 SHU0 0x0120-0x012F Interrupt Module (S12XINT) Map Address Name 0x0120 Reserved 0x0121 IVBR 0x0122 Reserved 0x0123 Reserved 0x0124 Reserved 0x0125 Reserved 0x0126 INT_XGPRIO 0x0127 INT_CFADDR 0x0128 INT_CFDATA0 0x0129 INT_CFDATA1 0x012A INT_CFDATA2 0x012B INT_CFDATA3 0x012C INT_CFDATA4 0x012D INT_CFDATA5 0x012E INT_CFDATA6 0x012F INT_CFDATA7 R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 IVB_ADDR[7:0] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 INT_CFADDR[7:4] RQST RQST RQST RQST RQST RQST RQST RQST 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 XILVL[2:0] 0 0 0 PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] PRIOLVL[2:0] MC9S12XDP512 Data Sheet, Rev. 2.21 1326 Freescale Semiconductor Appendix G Detailed Register Map 0x00130-0x0137 Asynchronous Serial Interface (SCI4) Map Address Name 0x0130 SCI4BDH1 0x0131 SCI4BDL1 0x0132 SCI4CR11 0x0130 SCI4ASR12 0x0131 SCI4ACR12 0x0132 SCI4ACR22 0x0133 SCI4CR2 0x0134 SCI4SR1 0x0135 SCI4SR2 0x0136 SCI4DRH 0x0137 SCI4DRL 1 2 Bit 7 R IREN W R SBR7 W R LOOPS W R RXEDGIF W R RXEDGIE W R 0 W R TIE W R TDRE W R AMAP W R R8 W R R7 W T7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 BERRV BERRIF BKDIF 0 0 0 0 BERRIE BKDIE 0 0 0 0 BERRM1 BERRM0 BKDFE TCIE RIE ILIE TE RE RWU SBK TC RDRF IDLE OR NF FE PF 0 0 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 0 R5 T5 R4 T4 R3 T3 R2 T2 R1 T1 R0 T0 T8 R6 T6 0 RAF Those registers are accessible if the AMAP bit in the SCI4SR2 register is set to zero Those registers are accessible if the AMAP bit in the SCI4SR2 register is set to one 0x0138-0x013F Asynchronous Serial Interface (SCI5) Map Address Name 0x0138 SCI5BDH1 0x0139 SCI5BDL1 0x013A SCI5CR11 0x0138 SCI5ASR12 0x0139 SCI5ACR12 0x013A SCI5ACR22 0x013B SCI5CR2 0x013C SCI5SR1 Bit 7 R IREN W R SBR7 W R LOOPS W R RXEDGIF W R RXEDGIE W R 0 W R TIE W R TDRE W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TNP1 TNP0 SBR12 SBR11 SBR10 SBR9 SBR8 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 SCISWAI RSRC M WAKE ILT PE PT 0 0 0 0 BERRV BERRIF BKDIF 0 0 0 0 BERRIE BKDIE 0 0 0 0 BERRM1 BERRM0 BKDFE TCIE RIE ILIE TE RE RWU SBK TC RDRF IDLE OR NF FE PF 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1327 Appendix G Detailed Register Map 0x0138-0x013F Asynchronous Serial Interface (SCI5) Map (continued) Address 1 2 Name 0x013D SCI5SR2 0x013E SCI5DRH 0x013F SCI5DRL Bit 7 R W R W R W AMAP R8 R7 T7 Bit 6 Bit 5 0 0 T8 R6 T6 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 TXPOL RXPOL BRK13 TXDIR 0 0 0 0 0 0 R5 T5 R4 T4 R3 T3 R2 T2 R1 T1 R0 T0 Bit 3 Bit 2 Bit 1 Bit 0 TIME WUPE SLPRQ INITRQ SLPAK INITAK RAF Those registers are accessible if the AMAP bit in the SCI5SR2 register is set to zero Those registers are accessible if the AMAP bit in the SCI5SR2 register is set to one 0x0140-0x017F Freescale Scalable CAN -- MSCAN (CAN0) Map Address 0x0140 0x0141 0x0142 0x0143 0x0144 0x0145 0x0146 0x0147 0x0148 0x0149 0x014A 0x014B 0x014C 0x014D 0x014E 0x014F Name Bit 7 R RXFRM W R CAN0CTL1 CANE W R CAN0BTR0 SJW1 W R CAN0BTR1 SAMP W R CAN0RFLG WUPIF W R CAN0RIER WUPIE W R 0 CAN0TFLG W R 0 CAN0TIER W R 0 CAN0TARQ W R 0 CAN0TAAK W R 0 CAN0TBSEL W R 0 CAN0IDAC W R 0 Reserved W R 0 CAN0MISC W R RXERR7 CAN0RXERR W R TXERR7 CAN0TXERR W CAN0CTL0 Bit 6 RXACT Bit 5 CSWAI Bit 4 SYNCH CLKSRC LOOPB LISTEN BORM WUPM SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 TXE2 TXE1 TXE0 0 0 0 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 TX2 TX1 TX0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 0 0 0 0 0 0 0 0 0 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 CSCIF 0 BOHOLD MC9S12XDP512 Data Sheet, Rev. 2.21 1328 Freescale Semiconductor Appendix G Detailed Register Map 0x0140-0x017F Freescale Scalable CAN -- MSCAN (CAN0) Map (continued) Address Name 0x0150- CAN0IDAR0- 0x0153 CAN0IDAR3 0x0154- CAN0IDMR0- 0x0157 CAN0IDMR3 0x0158- CAN0IDAR4- 0x015B CAN0IDAR7 0x015C CAN0IDMR4- - CAN0IDMR7 0x015F R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 R 0x0160- 0x016F CAN0RXFG 0x0170- 0x017F CAN0TXFG FOREGROUND RECEIVE BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) W R W FOREGROUND TRANSMIT BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) Detailed MSCAN Foreground Receive and Transmit Buffer Layout Address 0xXXX0 0xXXX1 0xXXX2 0xXXX3 0xXXX4 - 0xXXXB Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Extended ID Standard ID CANxRIDR0 Extended ID Standard ID CANxRIDR1 Extended ID Standard ID CANxRIDR2 Extended ID Standard ID CANxRIDR3 ID28 ID10 ID27 ID9 ID26 ID8 ID25 ID7 ID24 ID6 ID23 ID5 ID22 ID4 ID21 ID3 ID20 ID2 ID19 ID1 ID18 ID0 SRR=1 RTR IDE=1 IDE=0 ID17 ID16 ID15 ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DLC3 DLC2 DLC1 DLC0 R R W R R W R R W R R W R CANxRDSR0- CANxRDSR7 W R W R 0xXXXD Reserved W R 0xXXXE CANxRTSRH W R 0xXXXF CANxRTSRL W Extended ID R CANxTIDR0 W 0xXX10 Standard ID R W 0xXXXC CANRxDLR TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8 TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0 ID28 ID27 ID26 ID25 ID24 ID23 ID22 ID21 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1329 Appendix G Detailed Register Map Detailed MSCAN Foreground Receive and Transmit Buffer Layout (continued) Address Name 0xXX0x XX10 Extended ID CANxTIDR1 Standard ID 0xXX12 0xXX13 0xXX14 - 0xXX1B 0xXX1C 0xXX1D 0xXX1E 0xXX1F R W R W Extended ID R CANxTIDR2 W Standard ID R W Extended ID R CANxTIDR3 W Standard ID R W R CANxTDSR0- CANxTDSR7 W R W R CANxTTBPR W R CANxTTSRH W R CANxTTSRL W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ID20 ID19 ID18 SRR=1 IDE=1 ID17 ID16 ID15 ID2 ID1 ID0 RTR IDE=0 ID14 ID13 ID12 ID11 ID10 ID9 ID8 ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 RTR DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DLC3 DLC2 DLC1 DLC0 CANxTDLR PRIO7 PRIO6 PRIO5 PRIO4 PRIO3 PRIO2 PRIO1 PRIO0 TSR15 TSR14 TSR13 TSR12 TSR11 TSR10 TSR9 TSR8 TSR7 TSR6 TSR5 TSR4 TSR3 TSR2 TSR1 TSR0 0x0180-0x01BF Freescale Scalable CAN -- MSCAN (CAN1) Map (Sheet 1 of 3) Address Name 0x0180 CAN1CTL0 0x0181 CAN1CTL1 0x0182 CAN1BTR0 0x0183 CAN1BTR1 0x0184 CAN1RFLG 0x0185 CAN1RIER 0x0186 CAN1TFLG 0x0187 CAN1TIER 0x0188 CAN1TARQ Bit 7 R RXFRM W R CANE W R SJW1 W R SAMP W R WUPIF W R WUPIE W R 0 W R 0 W R 0 W Bit 6 RXACT Bit 5 CSWAI Bit 4 SYNCH Bit 3 Bit 2 Bit 1 Bit 0 TIME WUPE SLPRQ INITRQ SLPAK INITAK CLKSRC LOOPB LISTEN BORM WUPM SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 TXE2 TXE1 TXE0 0 0 0 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 0 ABTRQ2 ABTRQ1 ABTRQ0 CSCIF MC9S12XDP512 Data Sheet, Rev. 2.21 1330 Freescale Semiconductor Appendix G Detailed Register Map 0x0180-0x01BF Freescale Scalable CAN -- MSCAN (CAN1) Map (Sheet 2 of 3) Address Name 0x0189 CAN1TAAK 0x018A CAN1TBSEL 0x018B CAN1IDAC 0x018C Reserved 0x018D CAN1MISC 0x018E CAN1RXERR 0x018F CAN1TXERR 0x0190 CAN1IDAR0 0x0191 CAN1IDAR1 0x0192 CAN1IDAR2 0x0193 CAN1IDAR3 0x0194 CAN1IDMR0 0x0195 CAN1IDMR1 0x0196 CAN1IDMR2 0x0197 CAN1IDMR3 0x0198 CAN1IDAR4 0x0199 CAN1IDAR5 0x019A CAN1IDAR6 0x019B CAN1IDAR7 0x019C CAN1IDMR4 0x019D CAN1IDMR5 0x019E CAN1IDMR6 Bit 7 R 0 W R 0 W R 0 W R 0 W R 0 W R RXERR7 W R TXERR7 W R AC7 W R AC7 W R AC7 W R AC7 W R AM7 W R AM7 W R AM7 W R AM7 W R AC7 W R AC7 W R AC7 W R AC7 W R AM7 W R AM7 W R AM7 W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 TX2 TX1 TX0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 0 0 0 0 0 0 0 0 0 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 0 BOHOLD MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1331 Appendix G Detailed Register Map 0x0180-0x01BF Freescale Scalable CAN -- MSCAN (CAN1) Map (Sheet 3 of 3) Address Name R 0x019F CAN1IDMR7 W R 0x01A0- CAN1RXFG 0x01AF W R 0x01B0- CAN1TXFG 0x01BF W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 FOREGROUND RECEIVE BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) FOREGROUND TRANSMIT BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) 0x01C0-0x01FF Freescale Scalable CAN -- MSCAN (CAN2) Map Address 0x01C0 0x01C1 0x01C2 0x01C3 0x01C4 0x01C5 0x01C6 0x01C7 0x01C8 0x01C9 0x01CA 0x01CB 0x01CC 0x01CD 0x01CE 0x01CF 0x01D0 Name Bit 7 R CAN2CTL0 RXFRM W R CAN2CTL1 CANE W R CAN2BTR0 SJW1 W R CAN2BTR1 SAMP W R CAN2RFLG WUPIF W R CAN2RIER WUPIE W R 0 CAN2TFLG W R 0 CAN2TIER W R 0 CAN2TARQ W R 0 CAN2TAAK W R 0 CAN2TBSEL W R 0 CAN2IDAC W R 0 Reserved W R 0 CAN2MISC W R RXERR7 CAN2RXERR W R TXERR7 CAN2TXERR W R CAN2IDAR0 AC7 W Bit 6 RXACT Bit 5 CSWAI Bit 4 SYNCH Bit 3 Bit 2 Bit 1 Bit 0 TIME WUPE SLPRQ INITRQ SLPAK INITAK CLKSRC LOOPB LISTEN BORM WUPM SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 TXE2 TXE1 TXE0 0 0 0 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 TX2 TX1 TX0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 0 0 0 0 0 0 0 0 0 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 CSCIF 0 BOHOLD MC9S12XDP512 Data Sheet, Rev. 2.21 1332 Freescale Semiconductor Appendix G Detailed Register Map 0x01C0-0x01FF Freescale Scalable CAN -- MSCAN (CAN2) Map (continued) Address Name 0x01D1 CAN2IDAR1 0x01D2 CAN2IDAR2 0x01D3 CAN2IDAR3 0x01D4 CAN2IDMR0 0x01D5 CAN2IDMR1 0x01D6 CAN2IDMR2 0x01D7 CAN2IDMR3 0x01D8 CAN2IDAR4 0x01D9 CAN2IDAR5 0x01DA CAN2IDAR6 0x01DB CAN2IDAR7 0x01DC CAN2IDMR4 0x01DD CAN2IDMR5 0x01DE CAN2IDMR6 0x01DF CAN2IDMR7 0x01E0- 0x01EF CAN2RXFG 0x01F0- 0x01FF CAN2TXFG R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 FOREGROUND RECEIVE BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) FOREGROUND TRANSMIT BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1333 Appendix G Detailed Register Map 0x0200-0x023F Freescale Scalable CAN -- MSCAN (CAN3) Address Name 0x0200 CAN3CTL0 0x0201 CAN3CTL1 0x0202 CAN3BTR0 0x0203 CAN3BTR1 0x0204 CAN3RFLG 0x0205 CAN3RIER 0x0206 CAN3TFLG 0x0207 CAN3TIER 0x0208 CAN3TARQ 0x0209 CAN3TAAK 0x020A CAN3TBSEL 0x020B CAN3IDAC 0x020C Reserved 0x020D Reserved 0x020E CAN3RXERR 0x020F CAN3TXERR 0x0210 CAN3IDAR0 0x0211 CAN3IDAR1 0x0212 CAN3IDAR2 0x0213 CAN3IDAR3 0x0214 CAN3IDMR0 0x0215 CAN3IDMR1 Bit 7 R RXFRM W R CANE W R SJW1 W R SAMP W R WUPIF W R WUPIE W R 0 W R 0 W R 0 W R 0 W R 0 W R 0 W R 0 W R 0 W R RXERR7 W R TXERR7 W R AC7 W R AC7 W R AC7 W R AC7 W R AM7 W R AM7 W Bit 6 RXACT Bit 5 CSWAI Bit 4 SYNCH Bit 3 Bit 2 Bit 1 Bit 0 TIME WUPE SLPRQ INITRQ SLPAK INITAK CLKSRC LOOPB LISTEN BORM WUPM SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 TXE2 TXE1 TXE0 0 0 0 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 TX2 TX1 TX0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 0 0 0 0 0 0 0 0 0 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 CSCIF 0 BOHOLD MC9S12XDP512 Data Sheet, Rev. 2.21 1334 Freescale Semiconductor Appendix G Detailed Register Map 0x0200-0x023F Freescale Scalable CAN -- MSCAN (CAN3) (continued) Address Name 0x0216 CAN3IDMR2 0x0217 CAN3IDMR3 0x0218 CAN3IDAR4 0x0219 CAN3IDAR5 0x021A CAN3IDAR6 0x021B CAN3IDAR7 0x021C CAN3IDMR4 0x021D CAN3IDMR5 0x021E CAN3IDMR6 0x021F CAN3IDMR7 0x0220- 0x022F CAN3RXFG 0x0230- 0x023F CAN3TXFG R W R W R W R W R W R W R W R W R W R W R Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC7 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM7 AM6 AM5 AM4 AM3 AM2 AM1 AM0 FOREGROUND RECEIVE BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) W R W FOREGROUND TRANSMIT BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) 0x0240-0x027F Port Integration Module PIM_9DX (PIM) Map (Sheet 1 of 4) Address Name 0x0240 PTT 0x0241 PTIT 0x0242 DDRT 0x0243 RDRT 0x0244 PERT 0x0245 PPST 0x0246 Reserved 0x0247 Reserved R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PTT7 PTT6 PTT5 PTT4 PTT3 PTT2 PTT1 PTT0 PTIT7 PTIT6 PTIT5 PTIT4 PTIT3 PTIT2 PTIT1 PTIT0 DDRT7 DDRT7 DDRT5 DDRT4 DDRT3 DDRT2 DDRT1 DDRT0 RDRT7 RDRT6 RDRT5 RDRT4 RDRT3 RDRT2 RDRT1 RDRT0 PERT7 PERT6 PERT5 PERT4 PERT3 PERT2 PERT1 PERT0 PPST7 PPST6 PPST5 PPST4 PPST3 PPST2 PPST1 PPST0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1335 Appendix G Detailed Register Map 0x0240-0x027F Port Integration Module PIM_9DX (PIM) Map (Sheet 2 of 4) Address Name 0x0248 PTS 0x0249 PTIS 0x024A DDRS 0x024B RDRS 0x024C PERS 0x024D PPSS 0x024E WOMS 0x024F Reserved 0x0250 PTM 0x0251 PTIM 0x0252 DDRM 0x0253 RDRM 0x0254 PERM 0x0255 PPSM 0x0256 WOMM 0x0257 MODRR 0x0258 PTP 0x0259 PTIP 0x025A DDRP 0x025B RDRP 0x025C PERP 0x025D PPSP 0x025E PIEP 0x025F PIFP R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PTS7 PTS6 PTS5 PTS4 PTS3 PTS2 PTS1 PTS0 PTIS7 PTIS6 PTIS5 PTIS4 PTIS3 PTIS2 PTIS1 PTIS0 DDRS7 DDRS7 DDRS5 DDRS4 DDRS3 DDRS2 DDRS1 DDRS0 RDRS7 RDRS6 RDRS5 RDRS4 RDRS3 RDRS2 RDRS1 RDRS0 PERS7 PERS6 PERS5 PERS4 PERS3 PERS2 PERS1 PERS0 PPSS7 PPSS6 PPSS5 PPSS4 PPSS3 PPSS2 PPSS1 PPSS0 WOMS7 WOMS6 WOMS5 WOMS4 WOMS3 WOMS2 WOMS1 WOMS0 0 0 0 0 0 0 0 0 PTM7 PTM6 PTM5 PTM4 PTM3 PTM2 PTM1 PTM0 PTIM7 PTIM6 PTIM5 PTIM4 PTIM3 PTIM2 PTIM1 PTIM0 DDRM7 DDRM7 DDRM5 DDRM4 DDRM3 DDRM2 DDRM1 DDRM0 RDRM7 RDRM6 RDRM5 RDRM4 RDRM3 RDRM2 RDRM1 RDRM0 PERM7 PERM6 PERM5 PERM4 PERM3 PERM2 PERM1 PERM0 PPSM7 PPSM6 PPSM5 PPSM4 PPSM3 PPSM2 PPSM1 PPSM0 WOMM7 WOMM6 WOMM5 WOMM4 WOMM3 WOMM2 WOMM1 WOMM0 MODRR6 MODRR5 MODRR4 MODRR3 MODRR2 MODRR1 MODRR0 PTP7 PTP6 PTP5 PTP4 PTP3 PTP2 PTP1 PTP0 PTIP7 PTIP6 PTIP5 PTIP4 PTIP3 PTIP2 PTIP1 PTIP0 DDRP7 DDRP7 DDRP5 DDRP4 DDRP3 DDRP2 DDRP1 DDRP0 RDRP7 RDRP6 RDRP5 RDRP4 RDRP3 RDRP2 RDRP1 RDRP0 PERP7 PERP6 PERP5 PERP4 PERP3 PERP2 PERP1 PERP0 PPSP7 PPSP6 PPSP5 PPSP4 PPSP3 PPSP2 PPSP1 PPSS0 PIEP7 PIEP6 PIEP5 PIEP4 PIEP3 PIEP2 PIEP1 PIEP0 PIFP7 PIFP6 PIFP5 PIFP4 PIFP3 PIFP2 PIFP1 PIFP0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 1336 Freescale Semiconductor Appendix G Detailed Register Map 0x0240-0x027F Port Integration Module PIM_9DX (PIM) Map (Sheet 3 of 4) Address Name 0x0260 PTH 0x0261 PTIH 0x0262 DDRH 0x0263 RDRH 0x0264 PERH 0x0265 PPSH 0x0266 PIEH 0x0267 PIFH 0x0268 PTJ 0x0269 PTIJ 0x026A DDRJ 0x026B RDRJ 0x026C PERJ 0x026D PPSJ 0x026E PIEJ 0x026F PIFJ 0x0270 Reserved 0x0271 PT1AD0 0x0272 Reserved 0x0273 DDR1AD0 0x0274 Reserved 0x0275 RDR1AD0 0x0276 Reserved 0x0277 PER1AD0 R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PTH7 PTH6 PTH5 PTH4 PTH3 PTH2 PTH1 PTH0 PTIH7 PTIH6 PTIH5 PTIH4 PTIH3 PTIH2 PTIH1 PTIH0 DDRH7 DDRH7 DDRH5 DDRH4 DDRH3 DDRH2 DDRH1 DDRH0 RDRH7 RDRH6 RDRH5 RDRH4 RDRH3 RDRH2 RDRH1 RDRH0 PERH7 PERH6 PERH5 PERH4 PERH3 PERH2 PERH1 PERH0 PPSH7 PPSH6 PPSH5 PPSH4 PPSH3 PPSH2 PPSH1 PPSH0 PIEH7 PIEH6 PIEH5 PIEH4 PIEH3 PIEH2 PIEH1 PIEH0 PIFH7 PIFH6 PIFH5 PIFH4 PIFH3 PIFH2 PIFH1 PIFH0 PTJ7 PTJ6 PTJ5 PTJ4 PTJ2 PTJ1 PTJ0 PTIJ7 PTIJ6 PTIJ5 PTIJ4 PTIJ2 PTIJ1 PTIJ0 DDRJ7 DDRJ7 DDRJ5 DDRJ4 DDRJ2 DDRJ1 DDRJ0 RDRJ7 RDRJ6 RDRJ5 RDRJ4 RDRJ2 RDRJ1 RDRJ0 PERJ7 PERJ6 PERJ5 PERJ4 PERJ2 PERJ1 PERJ0 PPSJ7 PPSJ6 PPSJ5 PPSJ4 PPSJ2 PPSJ1 PPSJ0 PIEJ7 PIEJ6 PIEJ5 PIEJ4 PIEJ2 PIEJ1 PIEJ0 PIFJ7 PIFJ6 PIFJ5 PIFJ4 PIFJ2 PIFJ1 PIFJ0 0 0 0 0 0 0 0 0 PT1AD07 PT1AD06 PT1AD05 PT1AD04 PT1AD03 PT1AD02 PT1AD01 PT1AD00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DDR1AD0 DDR1AD0 DDR1AD0 DDR1AD0 DDR1AD0 DDR1AD0 DDR1AD0 DDR1AD0 7 6 5 4 3 2 1 1 0 0 0 0 0 0 0 0 RDR1AD0 RDR1AD0 RDR1AD0 RDR1AD0 RDR1AD0 RDR1AD0 RDR1AD0 RDR1AD0 7 6 5 4 3 2 1 0 0 0 0 0 0 0 0 0 PER1AD0 PER1AD0 PER1AD0 PER1AD0 PER1AD0 PER1AD0 PER1AD0 PER1AD0 7 6 5 4 3 2 1 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1337 Appendix G Detailed Register Map 0x0240-0x027F Port Integration Module PIM_9DX (PIM) Map (Sheet 4 of 4) Address Name 0x0278 PT0AD1 0x0279 PT1AD1 0x027A DDR0AD1 0x027B DDR1AD1 0x027C RDR0AD1 0x027D RDR1AD1 0x027E PER0AD1 0x027F PER1AD1 R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PT0AD1 23 PT0AD1 22 PT0AD1 21 PT0AD1 20 PT0AD1 19 PT0AD1 18 PT0AD1 17 PT0AD1 16 PT1AD1 15 PT1AD1 14 PT1AD1 13 PT1AD1 12 PT1AD1 11 PT1AD1 10 PT1AD1 9 PT1AD1 8 DDR0AD1 DDR0AD1 DDR0AD1 DDR0AD1 DDR0AD1 DDR0AD1 DDR0AD1 DDR0AD1 23 22 21 20 19 18 17 16 DDR1AD1 DDR1AD1 DDR1AD1 DDR1AD1 DDR1AD1 DDR1AD1 DDR1AD1 DDR1AD1 15 14 13 12 11 10 9 8 RDR0AD1 RDR0AD1 RDR0AD1 RDR0AD1 RDR0AD1 RDR0AD1 RDR0AD1 RDR0AD1 23 22 21 20 19 18 17 16 RDR1AD1 RDR1AD1 RDR1AD1 RDR1AD1 RDR1AD1 RDR1AD1 RDR1AD1 RDR1AD1 15 14 13 12 11 10 9 8 PER0AD1 PER0AD1 PER0AD1 PER0AD1 PER0AD1 PER0AD1 PER0AD1 PER0AD1 23 22 21 20 19 18 17 16 PER1AD1 PER1AD1 PER1AD1 PER1AD1 PER1AD1 PER1A1D PER1AD1 PER1AD1 15 14 13 12 11 10 9 8 0x0280-0x02BF Freescale Scalable CAN -- MSCAN (CAN4) Map Address 0x0280 0x0281 0x0282 0x0283 0x0284 0x0285 0x0286 0x0287 0x0288 0x0289 0x028A 0x028B 0x028C Name Bit 7 R CAN4CTL0 RXFRM W R CAN4CTL1 CANE W R CAN4BTR0 SJW1 W R CAN4BTR1 SAMP W R CAN4RFLG WUPIF W R CAN4RIER WUPIE W R 0 CAN4TFLG W R 0 CAN4TIER W R 0 CAN4TARQ W R 0 CAN4TAAK W R 0 CAN4TBSEL W R 0 CAN4IDAC W R 0 Reserved W Bit 6 RXACT Bit 5 CSWAI Bit 4 SYNCH Bit 3 Bit 2 Bit 1 Bit 0 TIME WUPE SLPRQ INITRQ SLPAK INITAK CLKSRC LOOPB LISTEN BORM WUPM SJW0 BRP5 BRP4 BRP3 BRP2 BRP1 BRP0 TSEG22 TSEG21 TSEG20 TSEG13 TSEG12 TSEG11 TSEG10 RSTAT1 RSTAT0 TSTAT1 TSTAT0 OVRIF RXF CSCIE RSTATE1 RSTATE0 TSTATE1 TSTATE0 OVRIE RXFIE 0 0 0 0 TXE2 TXE1 TXE0 0 0 0 0 TXEIE2 TXEIE1 TXEIE0 0 0 0 0 ABTRQ2 ABTRQ1 ABTRQ0 0 0 0 0 ABTAK2 ABTAK1 ABTAK0 0 0 0 0 TX2 TX1 TX0 IDAM1 IDAM0 0 IDHIT2 IDHIT1 IDHIT0 0 0 0 0 0 0 CSCIF 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 1338 Freescale Semiconductor Appendix G Detailed Register Map 0x0280-0x02BF Freescale Scalable CAN -- MSCAN (CAN4) Map (continued) Address Name 0x028D CAN4MISC 0x028E CAN4RXERR 0x028F CAN4TXERR 0x0290 CAN4IDAR0 0x0291 CAN4IDAR1 0x0292 CAN4IDAR2 0x0293 CAN4IDAR3 0x0294 CAN4IDMR0 0x0295 CAN4IDMR1 0x0296 CAN4IDMR2 0x0297 CAN4IDMR3 0x0298 CAN4IDAR4 0x0299 CAN4IDAR5 0x029A CAN4IDAR6 0x029B CAN4IDAR7 0x029C CAN4IDMR4 0x029D CAN4IDMR5 0x029E CAN4IDMR6 0x029F CAN4IDMR7 0x02A0- 0x02AF CAN4RXFG 0x02B0- 0x02BF CAN4TXFG Bit 7 R 0 W R RXERR7 W R TXERR7 W R AC7 W R AC7 W R AC7 W R AC7 W R AM7 W R AM7 W R AM7 W R AM7 W R AC7 W R AC7 W R AC7 W R AC7 W R AM7 W R AM7 W R AM7 W R AM7 W R W R W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 0 0 0 0 0 0 Bit 0 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0 TXERR6 TXERR5 TXERR4 TXERR3 TXERR2 TXERR1 TXERR0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AC6 AC5 AC4 AC3 AC2 AC1 AC0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 AM6 AM5 AM4 AM3 AM2 AM1 AM0 BOHOLD FOREGROUND RECEIVE BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) FOREGROUND TRANSMIT BUFFER (See Detailed MSCAN Foreground Receive and Transmit Buffer Layout) MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1339 Appendix G Detailed Register Map 0x02C0-0x02DF Analog-to-Digital Converter 10-Bit 8-Channel (ATD0) Map Address Name 0x02C0 ATD0CTL0 0x02C1 ATD0CTL1 0x02C2 ATD0CTL2 0x02C3 ATD0CTL3 0x02C4 ATD0CTL4 0x02C5 ATD0CTL5 0x02C6 ATD0STAT0 0x02C7 Reserved 0x02C8 ATD0TEST0 0x02C9 ATD0TEST1 0x02CA Reserved 0x02CB ATD0STAT1 0x02CC Reserved 0x02CD ATD0DIEN 0x02CE Reserved 0x02CF ATD0PTAD0 0x02D0 ATD0DR0H 0x02D1 ATD0DR0L 0x02D2 ATD0DR1H 0x02D3 ATD0DR1L 0x02D4 ATD0DR2H 0x02D5 ATD0DR2L R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 0 0 0 0 0 ETRIG SEL 0 0 0 ADPU AFFC AWAI S8C SRES8 DJM 0 SCF Bit 2 Bit 1 Bit 0 WRAP2 WRAP1 WRAP0 0 ETRIG CH2 ETRIG CH1 ETRIG CH0 ETRIGLE ETRIGP ETRIGE ASCIE S4C S2C S1C FIFO FRZ1 FRZ0 SMP1 SMP0 PRS4 PRS3 PRS2 PRS1 PRS0 DSGN SCAN MULT CC CB CA ETORF FIFOR 0 CC2 CC1 CC0 0 0 ASCIF U U U U U U U U U U U U U U U U U U 0 0 0 0 0 0 0 0 0 0 0 0 0 CCF7 CCF6 CCF5 CCF4 CCF3 CCF2 CCF1 CCF0 0 0 0 0 0 0 0 0 IEN7 IEN6 IEN5 IEN4 IEN3 IEN2 IEN1 IEN0 0 0 0 0 0 0 0 0 Bit7 6 5 4 3 2 1 BIT 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 SC MC9S12XDP512 Data Sheet, Rev. 2.21 1340 Freescale Semiconductor Appendix G Detailed Register Map 0x02C0-0x02DF Analog-to-Digital Converter 10-Bit 8-Channel (ATD0) Map (continued) Address Name 0x02D6 ATD0DR3H 0x02D7 ATD0DR3L 0x02D8 ATD0DR4H 0x02D9 ATD0DR4L 0x02DA ATD0DR5H 0x02DB ATD0DR5L 0x02DC ATD0DR6H 0x02DD ATD0DR6L 0x02DE ATD0DR7H 0x02DF ATD0DR7L R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit15 14 13 12 11 10 9 Bit8 Bit7 Bit6 0 0 0 0 0 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Bit 3 Bit 2 Bit 1 Bit 0 LVIE LVIF APIE APIF 0 0 0x02E0-0x02EF Reserved Address 0x02E0- 0x02EF Name Reserved R W 0x02F0-0x02F7 Voltage Regulator (VREG_3V3) Map Address Name 0x02F0 VREGHTCL 0x02F1 VREGCTRL 0x02F2 VREGAPICL 0x02F3 VREGAPITR 0x02F4 VREGAPIRH 0x02F5 VREGAPIRL 0x02F6 Reserved 0x02F7 Reserved Bit 7 R W R 0 W R APICLK W R APITR5 W R 0 W R APIR7 W R 0 W R 0 W Bit 6 Bit 5 Bit 4 Reserved for Factory Test 0 0 0 0 LVDS 0 0 0 0 APITR4 APITR3 APITR2 APITR1 APITR0 0 0 0 APIR11 APIR10 APIR9 APIR8 APIR6 APIR5 APIR4 APIR3 APIR2 APIR1 APIR0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 APIFE MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1341 Appendix G Detailed Register Map 0x02F8-0x02FF Reserved Address 0x02F8- 0x02FF Name Reserved R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 0x0300-0x0327 Pulse Width Modulator 8-Bit 8-Channel (PWM) Map Address 0x0300 0x0301 0x0302 0x0303 0x0304 0x0305 0x0306 0x0307 0x0308 0x0309 0x030A 0x030B 0x030C 0x030D 0x030E 0x030F 0x0310 0x0311 0x0312 0x0313 Name Bit 7 R PWME7 W R PWMPOL PPOL7 W R PWMCLK PCLK7 W R 0 PWMPRCLK W R PWMCAE CAE7 W R PWMCTL CON67 W R 0 PWMTST Test Only W R 0 PWMPRSC W R PWMSCLA Bit 7 W R PWMSCLB Bit 7 W R 0 PWMSCNTA W R 0 PWMSCNTB W R Bit 7 PWMCNT0 W 0 R Bit 7 PWMCNT1 W 0 R Bit 7 PWMCNT2 W 0 R Bit 7 PWMCNT3 W 0 R Bit 7 PWMCNT4 W 0 R Bit 7 PWMCNT5 W 0 R Bit 7 PWMCNT6 W 0 R Bit 7 PWMCNT7 W 0 PWME Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PWME6 PWME5 PWME4 PWME3 PWME2 PWME1 PWME0 PPOL6 PPOL5 PPOL4 PPOL3 PPOL2 PPOL1 PPOL0 PCLK6 PCLK5 PCLK4 PCLK3 PCLK2 PCLK1 PCLK0 PCKB2 PCKB1 PCKB0 PCKA2 PCKA1 PCKA0 CAE6 CAE5 CAE4 CAE3 CAE2 CAE1 CAE0 CON45 CON23 CON01 PSWAI PFRZ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6 5 4 3 2 1 Bit 0 6 5 4 3 2 1 Bit 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6 0 6 0 6 0 6 0 6 0 6 0 6 0 6 0 5 0 5 0 5 0 5 0 5 0 5 0 5 0 5 0 4 0 4 0 4 0 4 0 4 0 4 0 4 0 4 0 3 0 3 0 3 0 3 0 3 0 3 0 3 0 3 0 2 0 2 0 2 0 2 0 2 0 2 0 2 0 2 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 Bit 0 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 1342 Freescale Semiconductor Appendix G Detailed Register Map 0x0300-0x0327 Pulse Width Modulator 8-Bit 8-Channel (PWM) Map Address Name 0x0314 PWMPER0 0x0315 PWMPER1 0x0316 PWMPER2 0x0317 PWMPER3 0x0318 PWMPER4 0x0319 PWMPER5 0x031A PWMPER6 0x031B PWMPER7 0x031C PWMDTY0 0x031D PWMDTY1 0x031E PWMDTY2 0x031F PWMDTY3 0x0320 PWMDTY4 0x0321 PWMDTY5 0x0322 PWMDTY6 0x0323 PWMDTY7 0x0324 PWMSDN 0x0325 Reserved 0x0326 Reserved 0x0327 Reserved R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 Bit 7 6 5 4 3 2 1 Bit 0 PWM7IN PWMIE PWM7INL PWM7 ENA 0 0 0 PWM RSTRT 0 0 PWMIF 0 0 0 0 PWMLVL 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1343 Appendix G Detailed Register Map 0x0328-0x033F Reserved Address 0x0328- 0x033F Name Reserved R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 PFLT3 0 PFLT2 0 PFLMT1 0 PFLT1 0 PFLMT0 0 PFLT0 PCE3 PCE2 PCE1 PCE0 PMUX3 PMUX2 PMUX1 PMUX0 PINTE3 PINTE2 PINTE1 PINTE0 PTF3 PTF2 PTF1 PTF0 0x0340-0x0367 Periodic Interrupt Timer (PIT) Map Address Name 0x0340 PITCFLMT 0x0341 PITFLT 0x0342 PITCE 0x0343 PITMUX 0x0344 PITINTE 0x0345 PITTF 0x0346 PITMTLD0 0x0347 PITMTLD1 0x0348 PITLD0 (hi) 0x0349 PITLD0 (lo) 0x034A PITCNT0 (hi) 0x034B PITCNT0 (lo) 0x034C PITLD1 (hi) 0x034D PITLD1 (lo) 0x034E PITCNT1 (hi) 0x034F PITCNT1 (lo) 0x0350 PITLD2 (hi) 0x0351 PITLD2 (lo) 0x0352 PITCNT2 (hi) 0x0353 PITCNT2 (lo) R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 PITE PITSWAI PITFRZ 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 PMTLD7 PMTLD6 PMTLD5 PMTLD4 PMTLD3 PMTLD2 PMTLD1 PMTLD0 PMTLD7 PMTLD6 PMTLD5 PMTLD4 PMTLD3 PMTLD2 PMTLD1 PMTLD0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT15 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT7 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT15 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT7 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 PLD15 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD7 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT15 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT7 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 MC9S12XDP512 Data Sheet, Rev. 2.21 1344 Freescale Semiconductor Appendix G Detailed Register Map 0x0340-0x0367 Periodic Interrupt Timer (PIT) Map (continued) Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PLD14 PLD13 PLD12 PLD11 PLD10 PLD9 PLD8 PLD6 PLD5 PLD4 PLD3 PLD2 PLD1 PLD0 PCNT14 PCNT13 PCNT12 PCNT11 PCNT10 PCNT9 PCNT8 PCNT6 PCNT5 PCNT4 PCNT3 PCNT2 PCNT1 PCNT0 0 0 0 0 0 0 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 R 0x0354 PITLD3 (hi) PLD15 W R 0x0355 PITLD3 (lo) PLD7 W R 0x0356 PITCNT3 (hi) PCNT15 W R 0x0357 PITCNT3 (lo) PCNT7 W R 0 0x0358- Reserved 0x0367 W 0x0368-0x037F Reserved Address Name 0x0368- 0x037F Reserved R W 0x0380-0x03BF XGATE Map (Sheet 1 of 3) Address Name 0x0380 XGMCTL 0x0381 XGMCTL 0x0382 XGCHID 0x0383 Reserved 0x0384 XGVBR 0x0385 XGVBR 0x0386 XGVBR 0x0387 XGVBR 0x0388 XGIF 0x0389 XGIF 0x038A XGIF 0x023B XGIF 0x023C XGIF R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 XGEM XGFRZM XGDBGM XGSSM XGFACTM 0 XGS WEIFM XGIEM XGE XGFRZ XGDBG XGSS XGFACT XGSWEIF XGIE 0 0 XGCHID[6:0] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 0 0 0 XGVBR[15:8] 0 XGVBR[7:1] 0 0 0 0 0 0 0 XGIF_77 XGIF_76 XGIF_75 XGIF_74 XGIF_73 XGIF_72 XGIF_71 XGIF_70 XGIF_6F XGIF_6E XGIF_6D XGIF_6C XGIF_6B XGIF_6A XGIF_69 XGIF_68 XGIF_67 XGIF_66 XGIF_65 XGIF_64 XGIF_63 XGIF_62 XGIF_61 XGIF_60 XGIF_5F XGIF_5E XGIF_5D XGIF_5C XGIF_5B XGIF_5A XGIF_59 XGIF_58 XGIF_78 MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1345 Appendix G Detailed Register Map 0x0380-0x03BF XGATE Map (Sheet 2 of 3) Address Name 0x038D XGIF 0x038E XGIF 0x038F XGIF 0x0390 XGIF 0x0391 XGIF 0x0392 XGIF 0x0393 XGIF 0x0394 XGIF 0x0395 XGIF 0x0396 XGIF 0x0397 XGIF 0x0398 XGSWT (hi) 0x0399 XGSWT (lo) 0x039A XGSEM (hi) 0x039B XGSEM (lo) 0x039C Reserved 0x039D XGCCR 0x039E XGPC (hi) 0x039F XGPC (lo) 0x03A0 Reserved 0x03A1 Reserved 0x03A2 XGR1 (hi) 0x03A3 XGR1 (lo) R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 XGIF_57 XGIF_56 XGIF_55 XGIF_54 XGIF_53 XGIF_52 XGIF_51 XGIF_50 XGIF_4F XGIF_4E XGIF_4D XGIF_4C XGIF_4B XGIF_4A XGIF_49 XGIF_48 XGIF_47 XGIF_46 XGIF_45 XGIF_44 XGIF_43 XGIF_42 XGIF_41 XGIF_40 XGIF_3F XGIF_3E XGIF_3D XGIF_3C XGIF_3B XGIF_3A XGIF_39 XGIF_38 XGIF_37 XGIF_36 XGIF_35 XGIF_34 XGIF_33 XGIF_32 XGIF_31 XGIF_30 XGIF_2F XGIF_2E XGIF_2D XGIF_2C XGIF_2B XGIF_2A XGIF_29 XGIF_28 XGIF_27 XGIF_26 XGIF_25 XGIF_24 XGIF_23 XGIF_22 XGIF_21 XGIF_20 XGIF_1F XGIF_1E XGIF_1D XGIF_1C XGIF_1B XGIF_1A XGIF_19 XGIF_18 XGIF_17 XGIF_16 XGIF_15 XGIF_14 XGIF_13 XGIF_12 XGIF_11 XGIF_10 XGIF_0F XGIF_0E XGIF_0D XGIF_0C XGIF_0B XGIF_0A XGIF_09 0 0 0 0 0 0 0 0 0 0 0 0 0 XGSWTM[7:0] 0 0 0 0 0 0 0 0 0 0 XGN XGZ XGV XGC 0 XGSWT[7:0] 0 0 0 0 0 XGSEMM[7:0] XGSEM[7:0] 0 0 0 0 0 0 0 0 XGPC[15:8] XGPC[7:0] 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 XGR1[15:8] XGR1[7:0] MC9S12XDP512 Data Sheet, Rev. 2.21 1346 Freescale Semiconductor Appendix G Detailed Register Map 0x0380-0x03BF XGATE Map (Sheet 3 of 3) Address Name 0x03A4 XGR2 (hi) 0x03A5 XGR2 (lo) 0x03A6 XGR3 (hi) 0x03A7 XGR3 (lo) 0x03A8 XGR4 (hi) 0x03A9 XGR4 (lo) 0x03AA XGR5 (hi) 0x03AB XGR5(lo) 0x03AC XGR6 (hi) 0x03AD XGR6 (lo) 0x03AE XGR7 (hi) 0x03AF XGR7 (lo) 0x03B0- 0x03BF Reserved Bit 7 R W R W R W R W R W R W R W R W R W R W R W R W R W Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 XGR2[15:8] XGR2[7:0] XGR3[15:8] XGR3[7:0] XGR4[15:8] XGR4[7:0] XGR5[15:8] XGR5[7:0] XGR6[15:8] XGR6[7:0] XGR7[15:8] XGR7[7:0] 0 0 0 0 0 0 0 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 0 0 0 0 0 0 0 0 0x03C0-0x07FF Reserved Address Name 0x03C0 -0x07FF Reserved R W MC9S12XDP512 Data Sheet, Rev. 2.21 Freescale Semiconductor 1347 Appendix G Detailed Register Map MC9S12XDP512 Data Sheet, Rev. 2.21 1348 Freescale Semiconductor How to Reach Us: Home Page: www.freescale.com USA/Europe or Locations Not Listed: Freescale Semiconductor Technical Information Center, CH370 1300 N. Alma School Road Chandler, Arizona 85224 1-800-521-6274 or 480-768-2130 Europe, Middle East, and Africa: +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) Japan: Freescale Semiconductor Japan Ltd. Technical Information Center 3-20-1, Minami-Azabu, Minato-ku Tokyo 106-0047, Japan 0120-191014 or +81-3-3440-3569 Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong 852-26668334 For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 1-800-441-2447 or 303-675-2140 Fax: 303-675-2150 Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. Java and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other countries. The Bluetooth trademarks are owned by their proprietor and used by Freescale Semiconductor, Inc. under license. (c) Freescale Semiconductor, Inc. 2008. All rights reserved. MC9S12XDP512RMV2 Rev. 2.21 October 2009