L6392 High-voltage high and low side driver Features High voltage rail up to 600 V dV/dt immunity 50 V/nsec in full temperature range Driver current capability: - 290 mA source - 430 mA sink Switching times 75/35 nsec rise/fall with 1 nF load 3.3 V, 5 V TTL/CMOS inputs with hysteresis Integrated bootstrap diode Operational amplifier for advanced current sensing Adjustable dead-time Interlocking function Compact and simplified layout Bill of material reduction Flexible, easy and fast design SO-14 DIP-14 Description The L6392 is a high-voltage device manufactured with the BCD "OFF-LINE" technology. It is a single chip half-bridge gate driver for N-channel Power MOSFET or IGBT. The high side (floating) section is designed to stand a voltage rail up to 600 V. The logic inputs are CMOS/TTL compatible down to 3.3 V for easy interfacing microcontroller/DSP The IC embeds an operational amplifier suitable for advanced current sensing in applications such as field oriented motor control. Applications Motor driver for home appliances, factory automation, industrial drives. HID ballasts, power supply units. Table 1. August 2010 Device summary Order codes Package Packaging L6392N DIP-14 Tube L6392D SO-14 Tube L6392DTR SO-14 Tape and reel Doc ID 14494 Rev 5 1/20 www.st.com 20 Contents L6392 Contents 1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 4.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.1 AC operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5.2 DC operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6 Waveforms definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7 Typical application diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 8 Bootstrap driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8.1 CBOOT selection and charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 Doc ID 14494 Rev 5 L6392 1 Block diagram Block diagram Figure 1. VCC Block diagram BOOTSTRAP DRIVER 4 UV DETECTION FLOATING STRUCTURE from LVG 14 BOOT 13 HVG 12 OUT UV DETECTION HVG DRIVER HIN 3 LEVEL SHIFTER S R LOGIC 5V SHOOT THROUGH PREVENTION LIN 1 VCC SD GND DT LVG DRIVER LVG 10 2 7 5 DEAD TIME VCC OPOUT OPAMP 6 + 8 OP+ OP- 9 Doc ID 14494 Rev 5 3/20 Pin connection 2 L6392 Pin connection Figure 2. Table 2. Pins connection (top view) LIN 1 14 BOOT SD 2 13 HVG HIN 3 12 OUT VCC 4 11 NC DT 5 10 LVG OPOUT 6 9 OP- GND 7 8 OP+ Pin description Pin N# Pin name Type 1 LIN I Low side driver logic input (active low) I Shut down logic input (active low) 2 SD (1) Function 3 HIN I High side driver logic input (active high) 4 VCC P Lower section supply voltage 5 DT I Dead time setting 6 OPOUT O Opamp output 7 GND P Ground 8 OP+ I Opamp non inverting input 9 OP- I Opamp inverting input O Low side driver output 10 LVG (1) 11 NC 12 OUT (1) 13 HVG 14 BOOT Not connected P High side (floating) common voltage O High side driver output P Bootstrapped supply voltage 1. The circuit provides less than 1 V on the LVG and HVG pins (@ Isink = 10 mA), with VCC > 3 V. This allows to omitting the "bleeder" resistor connected between the gate and the source of the external MOSFET normally used to hold the pin low; the gate driver assures low impedance also in SD condition. 4/20 Doc ID 14494 Rev 5 L6392 3 Truth table Truth table Table 3. Truth table Inputs Note: Outputs SD LIN HIN LVG HVG L X X L L H L L H L H L H L L H H L L L H H H L H X: don't care Doc ID 14494 Rev 5 5/20 Electrical data L6392 4 Electrical data 4.1 Absolute maximum ratings Table 4. Absolute maximum rating Value Symbol Parameter Unit Min Max VCC Supply voltage - 0.3 + 21 V Vout Output voltage Vboot -21 Vboot +0.3 V Vboot Bootstrap voltage - 0.3 620 V Vhvg High side gate output voltage Vout - 0.3 Vboot + 0.3 V VIvg Low side gate output voltage -0.3 VCC + 0.3 V Vop+ Opamp non-inverting input -0.3 VCC + 0.3 V Vop- Opamp inverting input -0.3 VCC + 0.3 V Logic input voltage -0.3 15 V 50 V/ns Vi dVout/dt Allowed output slew rate Ptot Total power dissipation (TA = 25 C) 800 mW TJ Junction temperature 150 C Tstg Storage temperature 150 C -50 Note: ESD immunity for pins 12, 13 and 14 is guaranteed up to 1 kV (Human body model) 4.2 Thermal data Table 5. Symbol Rth(JA) 6/20 Thermal data Parameter Thermal resistance junction to ambient Doc ID 14494 Rev 5 SO-14 DIP-14 Unit 165 100 C/W L6392 4.3 Electrical data Recommended operating conditions Table 6. Recommended operating conditions Symbol Pin VCC 4 VBO (1) Vout Min Max Unit Supply voltage 12.5 20 V 14-12 Floating supply voltage 12.4 20 V 580 V 800 kHz 125 C 12 Parameter Test condition DC output voltage fsw Switching frequency TJ Junction temperature -9 (2) HVG, LVG load CL = 1nF -40 1. VBO = Vboot -Vout 2. LVG off. VCC = 12.5 V. Logic is operational if Vboot > 5 V. Doc ID 14494 Rev 5 7/20 Electrical characteristics L6392 5 Electrical characteristics 5.1 AC operation Table 7. AC operation electrical characteristics (VCC = 15 V; TJ =+25 C) Symbol ton toff tsd Pin tf Typ Max Unit 50 125 200 ns 50 125 200 ns 50 125 200 ns 30 ns 5 Dead time setting range (1) Matching dead time (2) RDT = 0; CL = 1 nF; CDT = 100 nF 0.1 0.18 0.25 RDT = 37 k;CL = 1 nF; CDT=100 nF 0.48 0.6 0.72 RDT = 136 k;CL=1 nF; CDT=100 nF 1.35 1.6 1.85 RDT = 260 k;CL=1 nF; CDT=100 nF 2.6 3.0 3.4 RDT = 0 ; CL=1 nF; CDT =100 nF 80 RDT = 37 k;CL=1 nF; CDT=100 nF 120 RDT = 136 k;CL=1 nF; CDT=100 nF 250 RDT = 260 k;CL=1 nF; CDT=100 nF 400 s ns Rise time CL = 1 nF 75 120 ns Fall time CL = 1 nF 35 70 ns 10, 13 1. See Figure 4 on page 9 2. MDT = | DTLH - DTHL | see Figure 5 on page 13 8/20 Min Delay matching, HS and LS turn-on/off MDT tr Test condition High/low side driver turnVout = 0 V 1 vs 10 on propagation delay = Vcc V 3 vs 13 High/low side driver turn- boot CL = 1 nF off propagation delay Vi = 0 to 3.3 V 2 vs Shut down to high/low See Figure 3 10, 13 side propagation delay MT DT Parameter Doc ID 14494 Rev 5 L6392 Electrical characteristics Figure 3. Timing characteristics 50% LIN 50% tr tf 90% LVG 90% 10% 10% ton toff 50% HIN 50% tr tf 90% HVG 90% 10% 10% ton toff 50% SD tf 90% LVG/HVG 10% tsd Figure 4. Typical dead time vs. DT resistor value $SSUR[LPDWHGIRUPXODIRU 5GWFDOFXODWLRQ W\S '7 XV 5GW>N@ A'7>V@ 5GW N2KP Doc ID 14494 Rev 5 9/20 Electrical characteristics L6392 5.2 DC operation Table 8. DC operation electrical characteristics (VCC = 15 V; TJ = +25 C) Symbol Pin Parameter Test condition Min Typ Max Unit Vcc UV hysteresis 1200 1500 1800 mV Vcc_thON Vcc UV turn ON threshold 11.5 12 12.5 V Vcc_thOFF Vcc UV turn OFF threshold 10 10.5 11 V Undervoltage quiescent supply current VCC = 10 V SD = 5 V; LIN = 5 V; HIN = GND; RDT = 0 ; OP + = GND; OP - = 5 V 120 150 A Quiescent current VCC = 15 V SD = 5 V; LIN = 5 V; HIN = GND; RDT = 0 ; OP + = GND; OP - = 5 V 680 1000 A Low supply voltage section Vcc_hys Iqccu 4 Iqcc Bootstrapped supply voltage section (1) VBO_hys VBO UV hysteresis 1200 1500 1800 mV VBO_thON VBO UV turn ON threshold 10.6 11.5 12.4 V VBO_thOFF VBO UV turn OFF threshold 9.1 10 10.9 V Undervoltage VBO quiescent current VBO = 9 V SD = 5 V; LIN and HIN = 5 V; RDT = 0 ; OP + = GND; OP - = 5 V 70 110 A IQBO VBO quiescent current VBO = 15 V SD = 5 V; LIN and HIN = 5 V; RDT = 0 ; OP + = GND; OP - = 5 V 150 210 A ILK High voltage leakage current Vhvg = Vout = Vboot = 600 V 10 A Bootstrap driver on resistance (2) LVG ON 14 IQBOU RDS(on) 10/20 Doc ID 14494 Rev 5 120 L6392 Table 8. Symbol Electrical characteristics DC operation electrical characteristics (VCC = 15 V; TJ = +25 C) (continued) Pin Parameter Test condition Min Typ Max Unit Driving buffers section Iso High/low side source short circuit current Vi = Vih (tp < 10 ms) 200 290 mA High/low side sink short circuit current Vi = Vil (tp < 10 ms) 250 430 mA 10, 13 Isi Logic inputs Vil Low logic level voltage 0.8 High logic level voltage Vih 1, 3 2.25 Single input voltage LIN and HIN connected together and floating HIN logic "1" input bias current HIN = 15 V IHINl HIN logic "0" input bias current HIN = 0 V ILINI LIN logic "0" input bias current LIN = 0 V ILINh LIN logic "1" input bias current LIN = 15 V ISDh SD logic "1" input bias current SD = 15 V SD logic "0" input bias current SD = 0 V Vil_S V 1, 2, 3 IHINh 110 V 175 0.8 V 260 A 1 A 20 A 1 A 100 A 1 A 3 3 6 1 10 30 2 ISDl 1. VBO = Vboot - Vout 2. RDSon is tested in the following way: RDSon = [(VCC - VCBOOT1) - (VCC - VCBOOT2)] / [I1(VCC,VCBOOT1) - I2(VCC,VCBOOT2)] where I1 is pin 14 current when VCBOOT = VCBOOT1, I2 when VCBOOT = VCBOOT2 Doc ID 14494 Rev 5 11/20 Electrical characteristics Table 9. Symbol OPAMP characteristics (VCC = 15 V, TJ = +25 C) Pin Parameter Test condition Input offset voltage Vio Iio Iib L6392 Min Input bias current Max Unit 6 mV 4 40 nA 100 200 nA VCC-4 V 150 mV Vic = 0 V, Vo = 7.5 V Input offset current 8, 9 Typ Vic = 0 V, Vo = 7.5 V (1) Vicm Input common mode voltage range VOL Low level output voltage RL = 10 k to VCC VOH High level output voltage RL = 10 k to GND 14 14.7 V Source, Vid = + 1 V; Vo = 0 V 16 30 mA Sink Vid = -1 V; Vo = VCC 50 80 mA Slew rate Vi = 1/4; CL = 100 pF; unity gain 2.5 3.8 V/s GBWP Gain bandwidth product Vo = 7.5 V 8 12 MHz Avd Large signal voltage gain RL = 2 k 70 85 dB SRV Power supply rejection ratio vs Vcc 60 75 dB 55 70 dB 6 Io SR CMRR Output short circuit current 0 Common mode rejection ratio 1. The direction of input current is out of the IC. 12/20 Doc ID 14494 Rev 5 75 L6392 Waveforms definitions 6 Waveforms definitions Figure 5. Dead time - timing waveforms INTE RLO CKIN G HIN INTE RLO CONTROL SIGNAL EDGES OVERLAPPED: INTERLOCKING + DEAD TIME CKIN G LIN LVG DTHL DTLH HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) gate driver outputs OFF (HALF-BRIDGE TRI-STATE) LIN CONTROL SIGNALS EDGES SYNCHRONOUS (*): DEAD TIME HIN LVG DTLH DTHL HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) gate driver outputs OFF (HALF-BRIDGE TRI-STATE) LIN CONTROL SIGNALS EDGES NOT OVERLAPPED, BUT INSIDE THE DEAD TIME: DEAD TIME HIN LVG DTLH DTHL HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) gate driver outputs OFF (HALF-BRIDGE TRI-STATE) LIN CONTROL SIGNALS EDGES NOT OVERLAPPED, OUTSIDE THE DEAD TIME: DIRECT DRIVING HIN LVG DTLH DTHL HVG gate driver outputs OFF (HALF-BRIDGE TRI-STATE) gate driver outputs OFF (HALF-BRIDGE TRI-STATE) (*) HIN and LIN can be connected togheter and driven by just one control signal Doc ID 14494 Rev 5 13/20 Typical application diagram L6392 7 Typical application diagram Figure 6. Application diagram BOOTSTRAP DRIVER VCC 4 UV DETECTION FLOATING STRUCTURE from LVG 14 BOOT UV DETECTION H.V. HVG DRIVER HIN 3 LEVEL SHIFTER S 13 HVG 12 OUT Cboot R LOGIC 5V SHOOT THROUGH PREVENTION LIN 1 TO LOAD VCC SD GND DT 2 LVG DRIVER LVG 10 SD LATCH 7 5 DEAD TIME OPAMP OPOUT + 6 8 9 14/20 Doc ID 14494 Rev 5 OP+ OP- - L6392 8 Bootstrap driver Bootstrap driver A bootstrap circuitry is needed to supply the high voltage section. This function is normally accomplished by a high voltage fast recovery diode (Figure 7 a). In the L6392 a patented integrated structure replaces the external diode. It is realized by a high voltage DMOS, driven synchronously with the low side driver (LVG), with diode in series, as shown in Figure 7 b. An internal charge pump (Figure 7 b) provides the DMOS driving voltage. 8.1 CBOOT selection and charging To choose the proper CBOOT value the external MOS can be seen as an equivalent capacitor. This capacitor CEXT is related to the MOS total gate charge: Q gate C EXT = ------------V gate The ratio between the capacitors CEXT and CBOOT is proportional to the cyclical voltage loss. It has to be: CBOOT >>> CEXT e.g.: if Qgate is 30 nC and Vgate is 10 V, CEXT is 3 nF. With CBOOT = 100 nF the drop would be 300 mV. If HVG has to be supplied for a long time, the CBOOT selection has to take into account also the leakage and quiescent losses. e.g.: HVG steady state consumption is lower than 200 A, so if HVG TON is 5 ms, CBOOT has to supply 1 C to CEXT. This charge on a 1F capacitor means a voltage drop of 1 V. The internal bootstrap driver gives a great advantage: the external fast recovery diode can be avoided (it usually has great leakage current). This structure can work only if VOUT is close to GND (or lower) and in the meanwhile the LVG is on. The charging time (Tcharge) of the CBOOT is the time in which both conditions are fulfilled and it has to be long enough to charge the capacitor. The bootstrap driver introduces a voltage drop due to the DMOS RDSON (typical value: 120 ). At low frequency this drop can be neglected. Anyway increasing the frequency it must be taken in to account. The following equation is useful to compute the drop on the bootstrap DMOS: Q gate V drop = I ch arg e R dson V drop = ------------------ R dson T ch arg e where Qgate is the gate charge of the external power MOS, Rdson is the on resistance of the bootstrap DMOS, and Tcharge is the charging time of the bootstrap capacitor. Doc ID 14494 Rev 5 15/20 Bootstrap driver L6392 For example: using a power MOS with a total gate charge of 30 nC the drop on the bootstrap DMOS is about 1 V, if the Tcharge is 5 s. In fact: 30nC V drop = --------------- 120 0.7V 5s Vdrop has to be taken into account when the voltage drop on CBOOT is calculated: if this drop is too high, or the circuit topology doesn't allow a sufficient charging time, an external diode can be used. Figure 7. Bootstrap driver DBOOT VS BOOT BOOT VS H.V. HVG H.V. HVG CBOOT VOUT TO LOAD TO LOAD LVG LVG a 16/20 CBOOT VOUT b Doc ID 14494 Rev 5 D99IN1067 L6392 9 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark. Figure 8. DIP-14 mechanical data and package dimensions mm DIM. MIN. a1 0.51 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L OUTLINE AND MECHANICAL DATA 3.3 0.130 DIP14 Z 1.27 2.54 0.050 0.100 Doc ID 14494 Rev 5 17/20 Package mechanical data Figure 9. L6392 SO-14 mechanical data and package dimensions mm inch DIM. MIN. TYP. MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.10 0.30 0.004 0.012 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.01 8.55 8.75 0.337 0.344 3.80 4.0 0.150 0.157 D (1) E e 1.27 0.050 H 5.8 6.20 0.228 0.244 h 0.25 0.50 0.01 0.02 L 0.40 1.27 0.016 0.050 k ddd OUTLINE AND MECHANICAL DATA 0 (min.), 8 (max.) 0.10 0.004 (1) "D" dimension does not include mold flash, protusions or gate burrs. Mold flash, protusions or gate burrs shall not exceed 0.15mm per side. SO14 0016019 D 18/20 Doc ID 14494 Rev 5 L6392 10 Revision history Revision history Table 10. Document revision history Date Revision Changes 29-Feb-2008 1 Initial release 18-Mar-2008 2 Cover page updated 17-Sep-2008 3 Updated Table 4 on page 6, Table 4 on page 6, Table 9 on page 12 17-Feb-2009 4 Updated Table 7 on page 8, Table 8 on page 10, Table 9 on page 12 Added Table 4 on page 9 11-Aug-2010 5 Updated cover page, Table 1 on page 1, Table 7 on page 8, Table 9 on page 12 Doc ID 14494 Rev 5 19/20 L6392 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20 Doc ID 14494 Rev 5