SO 8 ACT102H-600D AC Thyristor power switch Rev. 1 -- 23 December 2010 Product data sheet 1. Product profile 1.1 General description An AC Thyristor power switch with very high noise immunity and over-voltage protection configured for negative gate triggering in a SOT96-1 (SO8) small surface-mountable plastic package 1.2 Features and benefits Exclusive negative gate triggering Full cycle AC conduction High noise immunity Remote gate separates the gate driver from the effects of the load current Safe clamping of low energy over-voltage transients Self-protective turn-on during high energy voltage transients Surface-mountable package Very sensitive gate for lowest gate trigger current 1.3 Applications Fan motor circuits Pump motor circuits Lower-power highly inductive, resistive and safety loads 1.4 Quick reference data Table 1. Quick reference data Symbol Parameter VDRM repetitive peak off-state voltage IGT gate trigger current Conditions Min Typ Max Unit - - 600 V VD = 12 V; IT = 100 mA; LD+ G-; Tj = 25 C; see Figure 7 0.5 - 5 mA VD = 12 V; IT = 100 mA; LDG-; Tj = 25 C; see Figure 7 0.5 - 5 mA IT(RMS) RMS on-state current full sine wave; Tamb 100 C; see Figure 3; see Figure 1 - - 0.2 A dVD/dt rate of rise of off-state voltage VDM = 402 V; Tj = 125 C; gate open circuit; exponential waveform; see Figure 11 300 - - V/s ACT102H-600D NXP Semiconductors AC Thyristor power switch Table 1. Quick reference data ...continued Symbol Parameter Conditions Min Typ Max Unit VCL clamping voltage ICL = 100 A; tp = 1 ms; Tj 125 C; see Figure 14 650 - - V VPP peak pulse voltage Tj 25 C; non-repetitive, off-state; see Figure 2 - - 2 kV VT on-state voltage IT = 0.3 A; see Figure 10 - - 1.2 V 2. Pinning information Table 2. Pinning information Pin Symbol Description 1 n.c. not connected 2 LD Load 3 n.c. not connected 4 n.c. not connected 5 G Gate 6 CM Common 7 CM Common 8 n.c. not connected Simplified outline 8 Graphic symbol LD 5 G CM 1 4 001aaj924 SOT96-1 (SO8) 3. Ordering information Table 3. Ordering information Type number ACT102H-600D ACT102H-600D Product data sheet Package Name Description Version SO8 plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 2 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 4. Limiting values Table 4. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions VDRM repetitive peak off-state voltage IT(RMS) RMS on-state current ITSM non-repetitive peak on-state current Min Max Unit - 600 V full sine wave; Tamb 100 C; see Figure 3; see Figure 1 - 0.2 A full sine wave; Tj(init) = 25 C; tp = 16.7 ms - 8.8 A full sine wave; Tj(init) = 25 C; tp = 20 ms; see Figure 4; see Figure 5 - 8 A I2t I2t for fusing tp = 10 ms; sine-wave pulse - 0.32 A2s dIT/dt rate of rise of on-state current IT = 1 A; IG = 20 mA; dIG/dt = 0.2 A/s - 50 A/s IGM peak gate current t = 20 s - 1 A VGM peak gate voltage positive applied gate voltage - 15 V PGM peak gate power - 2 W PG(AV) average gate power - 0.1 W Tstg storage temperature -40 150 C Tj junction temperature - 125 C VPP peak pulse voltage - 2 kV over any 20 ms period Tj 25 C; non-repetitive, off-state; see Figure 2 003aaf740 0.24 IT(RMS) (A) 0.20 IEC 61000-4-5 Standards Surge Generator Open Circuit Voltage 1.2 s/50 s waveform 0.16 0.12 RGen R L 2 150 5 H Surge pulse 0.08 Load Model RG 220 DUT 003aad077 0.04 0 -50 Fig 1. 0 50 100 150 Ta (C) RMS on-state current as a function of solder point temperature; maximum values ACT102H-600D Product data sheet Fig 2. Test circuit for inductive and resistive loads with conditions equivalent to IEC 61000-4-5 All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 3 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 003aaf739 0.20 Ptot (W) = 180 0.16 0.12 0.08 0.04 0 0 0.04 0.08 0.12 0.16 0.20 IT(RMS) (A) Fig 3. Total power dissipation as a function of RMS on-state current; maximum values 003aac804 10 ITSM (A) 8 6 4 ITSM IT t 2 1/f Tj(init) = 25 C max 0 1 102 10 number of cycles 103 f = 50 Hz Fig 4. Non-repetitive peak on-state current as a function of the number of sinusoidal current cycles; maximum values ACT102H-600D Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 4 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 003aaf756 103 ITSM IT ITSM (A) t tp 102 Tj(init) = 25 C max 10 1 10-5 10-4 10-3 10-2 10-1 tp (s) Fig 5. Non-repetitive peak on-state current as a function of pulse width; maximum values 5. Thermal characteristics Table 5. Thermal characteristics Symbol Parameter Conditions Min Typ Max Unit Rth(j-a) thermal resistance from junction to ambient full cycle; see Figure 6 - 150 - K/W 003aaf741 103 Zth(j-a) (K/W) 102 10 P tp 1 10-3 10-2 10-1 1 10 102 t 103 tp (s) Fig 6. Transient thermal impedance from junction to lead as a function of pulse width ACT102H-600D Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 5 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 6. Characteristics Table 6. Characteristics Symbol Parameter Conditions Min Typ Max Unit IGT gate trigger current VD = 12 V; IT = 100 mA; LD+ G-; Tj = 25 C; see Figure 7 0.5 - 5 mA VD = 12 V; IT = 100 mA; LD- G-; Tj = 25 C; see Figure 7 0.5 - 5 mA IL latching current VD = 12 V; IG = 12 mA; Tj = 25 C; see Figure 8 - - 25 mA IH holding current VD = 12 V; Tj = 25 C; see Figure 9 - - 20 mA VT on-state voltage IT = 0.3 A; see Figure 10 - - 1.2 V VGT gate trigger voltage VD = 12 V; IT = 100 mA; Tj = 25 C - - 0.9 V VD = 12 V; IT = 100 mA; Tj 125 C 0.15 - - V off-state current ID VD = 600 V; Tj 125 C - - 0.2 mA VD = 600 V; Tj 25 C - - 2 A dVD/dt rate of rise of off-state voltage VDM = 402 V; Tj = 125 C; gate open circuit; exponential waveform; see Figure 11 300 - - V/s dIcom/dt rate of change of commutating current VD = 400 V; Tj = 125 C; IT(RMS) = 1 A; dVcom/dt = 15 V/s; gate open circuit; see Figure 12; see Figure 13 0.15 - - A/ms VCL clamping voltage ICL = 100 A; tp = 1 ms; Tj 125 C; see Figure 14 650 - - V 003aac809 3 IGT IL IL(25C) (1) IGT(25C) 2 003aac811 3 2 (2) 1 1 (2) 0 -50 (1) 0 50 100 Tj (C) 0 -50 150 0 50 100 150 Tj (C) (1) LD+ G(2) LD- GFig 7. Normalized gate trigger current as a function of junction temperature ACT102H-600D Product data sheet Fig 8. Normalized latching current as a function of junction temperature All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 6 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 003aac810 3 003aaf722 2.0 IT (A) IH IH(25C) 1.5 2 1.0 (1) 1 (2) (3) 0.5 0 -50 Fig 9. 0 50 100 0.0 0.0 150 0.5 1.0 1.5 Tj (C) Normalized holding current as a function of junction temperature 2.0 Fig 10. On-state current as a function of on-state voltage 003aac813 12 A B VT (V) 003aac814 12 A B 10 8 8 6 4 4 2 0 0 25 50 75 100 125 25 50 75 100 Tj (C) 125 Tj (C) A is dVD/dt at condition Tj C A is dIcom/dt at condition Tj C B is dVD/dt at condition Tj 125 C B is dIcom/dt at condition Tj 125 C VD = 400 V Fig 11. Normalized rate of rise of off-state voltage as a function of junction temperature ACT102H-600D Product data sheet Fig 12. Normalized critical rate of rise of commutating current as a function of junction temperature All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 7 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 003aac815 2.0 003aac817 1.2 A [B] VCL VCL(25C) A [spec] 1.5 0.8 1.0 0.4 0.5 0 10-1 1 102 10 B (V/s) 0 -50 0 50 100 150 Tj (C) A[B] is dIcom/dt at condition B, dVcom/dt A[spec] is the specified data sheet value of dIcom/dt turn-off time < 20 ms Fig 13. Normalized critical rate of change of commutating current as a function of critical rate of change of commutating voltage; minimum values ACT102H-600D Product data sheet Fig 14. Normalized clamping voltage (upper limit) as a function of junction temperature; minimum values All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 8 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 7. Package outline SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1 D E A X c y HE v M A Z 5 8 Q A2 A (A 3) A1 pin 1 index Lp 1 L 4 e detail X w M bp 0 2.5 5 mm scale DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT A max. A1 A2 A3 bp c D (1) E (2) e HE L Lp Q v w y Z (1) mm 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 5.0 4.8 4.0 3.8 1.27 6.2 5.8 1.05 1.0 0.4 0.7 0.6 0.25 0.25 0.1 0.7 0.3 0.069 0.010 0.057 0.004 0.049 0.01 0.019 0.0100 0.014 0.0075 0.20 0.19 0.16 0.15 0.05 0.01 0.01 0.004 0.028 0.012 inches 0.244 0.039 0.028 0.041 0.228 0.016 0.024 o 8 o 0 Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. REFERENCES OUTLINE VERSION IEC JEDEC SOT96-1 076E03 MS-012 JEITA EUROPEAN PROJECTION ISSUE DATE 99-12-27 03-02-18 Fig 15. Package outline SOT96-1 (SO8) ACT102H-600D Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 9 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 8. Soldering 5.50 0.60 (8x) 1.30 4.00 6.60 7.00 1.27 (6x) solder lands occupied area placement accuracy 0.25 Dimensions in mm sot096-1_fr Fig 16. Reflow soldering footprint for SOT96-1 (SO8) 1.20 (2x) 0.60 (6x) enlarged solder land 0.3 (2x) 1.30 4.00 6.60 7.00 1.27 (6x) 5.50 board direction solder lands occupied area solder resist placement accurracy 0.25 Dimensions in mm sot096-1_fw Fig 17. Wave soldering footprint for SOT96-1 (SO8) ACT102H-600D Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 10 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 9. Revision history Table 7. Revision history Document ID Release date Data sheet status Change notice Supersedes ACT102H-600D v.1 20101223 Product data sheet - - ACT102H-600D Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 11 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 10. Legal information 10.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term 'short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 10.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 10.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Quick reference data -- The Quick reference data is an extract of the product data given in the Limiting values and Characteristics sections of this document, and as such is not complete, exhaustive or legally binding. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective ACT102H-600D Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 12 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from national authorities. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. 10.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. Adelante, Bitport, Bitsound, CoolFlux, CoReUse, DESFire, EZ-HV, FabKey, GreenChip, HiPerSmart, HITAG, IC-bus logo, ICODE, I-CODE, ITEC, Labelution, MIFARE, MIFARE Plus, MIFARE Ultralight, MoReUse, QLPAK, Silicon Tuner, SiliconMAX, SmartXA, STARplug, TOPFET, TrenchMOS, TriMedia and UCODE -- are trademarks of NXP B.V. HD Radio and HD Radio logo -- are trademarks of iBiquity Digital Corporation. 11. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com ACT102H-600D Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 23 December 2010 (c) NXP B.V. 2010. All rights reserved. 13 of 14 ACT102H-600D NXP Semiconductors AC Thyristor power switch 12. Contents 1 1.1 1.2 1.3 1.4 2 3 4 5 6 7 8 9 10 10.1 10.2 10.3 10.4 11 Product profile . . . . . . . . . . . . . . . . . . . . . . . . . . .1 General description . . . . . . . . . . . . . . . . . . . . . .1 Features and benefits . . . . . . . . . . . . . . . . . . . . .1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Quick reference data . . . . . . . . . . . . . . . . . . . . .1 Pinning information . . . . . . . . . . . . . . . . . . . . . . .2 Ordering information . . . . . . . . . . . . . . . . . . . . . .2 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . .3 Thermal characteristics . . . . . . . . . . . . . . . . . . .5 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Package outline . . . . . . . . . . . . . . . . . . . . . . . . . .9 Soldering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . 11 Legal information. . . . . . . . . . . . . . . . . . . . . . . .12 Data sheet status . . . . . . . . . . . . . . . . . . . . . . .12 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Contact information. . . . . . . . . . . . . . . . . . . . . .13 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP B.V. 2010. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 23 December 2010 Document identifier: ACT102H-600D