LM6152/LM6154
Dual and Quad 75 MHz GBW Rail-to-Rail I/O Operational
Amplifiers
General Description
Using patented circuit topologies, the LM6152/54 provides
new levels of speed vs. power performance in applications
where low voltage supplies or power limitations previously
made compromise necessary. With only 1.4 mA/amplifier
supply current, the 75 MHz gain bandwidth of this device
supports new portable applications where higher power de-
vices unacceptably drain battery life. The slew rate of the de-
vices increases with increasing input differential voltage,
thus allowing the device to handle capacitive loads while
maintaining large signal amplitude.
The LM6152/54 can be driven by voltages that exceed both
power supply rails, thus eliminating concerns about exceed-
ing the common-mode voltage range. The rail-to-rail output
swing capability provides the maximum possible dynamic
range at the output. This is particularly important when oper-
ating on low supply voltages.
Operating on supplies from 2.7V to over 24V, the LM6152/54
is excellent for a very wide range of applications, from bat-
tery operated systems with large bandwidth requirements to
high speed instrumentation.
Features
At V
S
= 5V, Typ unless noted
nGreater than Rail-to-Rail Input CMVR −0.25V to 5.25V
nRail-to-Rail Output Swing 0.01V to 4.99V
nWide Gain-Bandwidth: 75 MHz @100 kHz
nSlew Rate:
Small signal 5V/µs
Large signal 45V/µs
nLow supply current 1.4mA/amplifier
nWide supply range 2.7V to 24V
nFast settling time of 1.1µs for 2V step (to 0.01%)
nPSRR 91 dB
nCMRR 84 dB
Applications
nPortable high speed instrumentation
nSignal conditioning amplifier/ADC buffers
nBarcode scanners
Connection Diagrams
8-Pin DIP/SO
DS012350-3
Top View
14-Pin DIP/SO
DS012350-4
Top View
August 2000
LM6152/LM6154Dual and Quad 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers
© 2000 National Semiconductor Corporation DS012350 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
ESD Tolerance (Note 2) 2500V
Differential Input Voltage 15V
Voltage at Input/Output
Pin (V
+
) + 0.3V, (V
) −0.3V
Supply Voltage (V
+
−V
) 35V
Current at Input Pin ±10mA
Current at Output Pin
(Note 3) ±25mA
Current at Power Supply
Pin 50mA
Lead Temperature
(soldering, 10 sec) 260˚C
Storage Temperature
Range -65˚C to +150˚C
Junction Temperature
(Note 4) 150˚C
Operating Ratings (Note 1)
Supply Voltage 2.7V V
S
24V
Junction Temperature Range
LM6152,LM6154 0˚C T
J
+ 70˚C
Thermal Resistance (θ
JA
)
N Pkg, 8-pin Molded Dip 115˚C/W
M Pkg, 8-pin Surface Mount 193˚C/W
N Pkg, 14-pin Molded Dip 81˚C/W
M Pkg, 14-pin Surface Mount 126˚C/W
5.0V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 5.0V, V
= 0V, V
CM
=V
O
=V
+
/2 and R
L
>1Mto V
+
/2.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions
Typ
(Note 5) LM6154AC
LM6152AC
Limit
(Note 6)
LM6154BC
LM6152BC
Limt
(Note 6) Units
V
OS
Input Offset Voltage 0.54 2
45
7mV
max
TCV
OS
Input Offset Voltage Average Drift 10 µV/˚C
I
B
Input Bias Current 0V V
CM
5V 500
750 980
1500 980
1500 nA
max
I
OS
Input Offset Current 32
40 100
160 100
160 nA
max
R
IN
Input Resistance, CM 0V V
CM
4V 30 M
CMRR Common Mode Rejection Ratio 0V V
CM
4V 94 70 70 dB min
0V V
CM
5V 84 60 60
PSRR Power Supply Rejection Ratio 5V V
+
24V 91 80 80 dB min
V
CM
Input Common-Mode Voltage Range Low −0.25 0 0 V
High 5.25 5.0 5.0 V
A
V
Large Signal Voltage Gain R
L
= 10k214 50 50 V/mV
min
V
O
Output Swing
R
L
= 100k0.006 0.02
0.03 0.02
0.03 V
max
4.992 4.97
4.96 4.97
4.96 V
min
R
L
=2k0.04 0.10
0.12 0.10
0.12 V
max
4.89 4.80
4.70 4.80
4.70 V
min
I
SC
Output Short Circuit Current Sourcing
6.2
3
2.5 3
2.5 mA
min
27
17 27
17 mA
max
Sinking
16.9
7
57
5mA
min
40 40 mA
max
LM6152/LM6154
www.national.com 2
5.0V DC Electrical Characteristics (Continued)
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 5.0V, V
= 0V, V
CM
=V
O
=V
+
/2 and R
L
>1Mto V
+
/2.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions
Typ
(Note 5) LM6154AC
LM6152AC
Limit
(Note 6)
LM6154BC
LM6152BC
Limt
(Note 6) Units
I
S
Supply Current Per Amplifier 1.4 2
2.25 2
2.25 mA
max
5.0V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 5.0V, V
= 0V, V
CM
=V
O
=V
+
/2 and R
L
>1Mto V
+
/2.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions
Typ
(Note 5) LM6154AC
LM6152AC
Limit
(Note 6)
LM6154BC
LM6152BC
Limt
(Note 6) Units
SR Slew Rate ±4V Step @V
S
=±6V,
R
S
<1k30 24
15 24
15 V/µs
min
GBW Gain-Bandwidth Product f = 100 kHz 75 MHz
Amp-to-Amp Isolation R
L
= 10k125 dB
e
n
Input-Referred Voltage Noise f = 1 kHz 9 nV
i
n
Input-Referred Current Noise f = 1 kHz 0.34 pA
T.H.D Total Harmonic Distortion f = 10 kHz, R
L
= 10k0.002 %
ts Settling Time 2V Step to 0.01% 1.1 µs
2.7V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 2.7V, V
= 0V, V
CM
=V
O
=V
+
/2 and R
L
>1Mto V
+
/2.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions
Typ
(Note 5) LM6154AC
LM6152AC
Limit
(Note 6)
LM6154BC
LM6152BC
Limt
(Note 6) Units
V
OS
Input Offset Voltage 0.8 2
55
8mV
max
TCV
OS
Input Offset Voltage Average Drift 10 µV/˚C
I
B
Input Bias Current 500 nA
I
OS
Input Offset Current 50 nA
R
IN
Input Resistance, CM 0V V
CM
1.8V 30 M
CMRR Common Mode Rejection Ratio 0V V
CM
1.8V 88 dB
0V V
CM
2.7V 78
PSRR Power Supply Rejection Ratio 3V V
+
5V 69 dB
V
CM
Input Common-Mode Voltage Range Low −0.25 0 0 V
High 2.95 2.7 2.7 V
A
V
Large Signal Voltage Gain R
L
= 10k5.5 V/mV
V
O
Output Swing R
L
= 10k0.032 0.07
0.11 0.07
0.11 V
max
2.68 2.64
2.62 2.64
2.62 V
min
I
S
Supply Current Per Amplifier 1.35 mA
LM6152/LM6154
www.national.com3
2.7V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 2.7V, V
= 0V, V
CM
=V
O
=V
+
/2 and R
L
>1Mto V
+
/2.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions
Typ
(Note 5) LM6154AC
LM6152AC
Limit
(Note 6)
LM6154BC
LM6152BC
Limt
(Note 6) Units
GBW Gain-Bandwidth Product f = 100kHz 80 MHz
24V DC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 24V, V
= 0V, V
CM
=V
O
=V
+
/2 and R
L
>1Mto V
+
/2.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions
Typ
(Note 5) LM6154AC
LM6152AC
Limit
(Note 6)
LM6154BC
LM6152BC
Limt
(Note 6) Units
V
OS
Input Offset Voltage 0.3 2
47
9mV
max
TCV
OS
Input Offset Voltage Average Drift 10 µV/˚C
I
B
Input Bias Current 500 nA
I
OS
Input Offset Current 32 nA
R
IN
Input Resistance, CM 0V V
CM
23V 60 Meg
CMRR Common Mode Rejection Ratio 0V V
CM
23V 94 dB
0V V
CM
24V 84
PSRR Power Supply Rejection Ratio 0V V
CM
24V 95 dB
V
CM
Input Common-Mode Voltage Range Low −0.25 0 0 V
High 24.25 24 24 V
A
V
Large Signal Voltage Gain R
L
= 10k55 V/mV
V
O
Output Swing R
L
= 10k0.044 0.075
0.090 0.075
0.090 V
max
23.91 23.8
23.7 23.8
23.7 V
min
I
S
Supply Current Per Amplifier 1.6 2.25
2.50 2.25
2.50 mA
max
24V AC Electrical Characteristics
Unless otherwise specified, all limits guaranteed for T
J
= 25˚C, V
+
= 24V, V
= 0V, V
CM
=V
O
=V
+
/2 and R
L
>1Mto V
+
/2.
Boldface limits apply at the temperature extremes.
Symbol Parameter Conditions
Typ
(Note 5) LM6154AC
LM6152AC
Limit
(Note 6)
LM6154BC
LM6152BC
Limt
(Note 6) Units
GBW Gain-Bandwidth Product f = 100kHz 80 MHz
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is in-
tended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Human body model, 1.5kin series with 100pF.
Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150˚C.
Note 4: The maximum power dissipation is a function of TJ(max) ,θJA, and TA. The maximum allowable power dissipation at any ambient temperature
is PD=(T
J(max)–T A)/θJA. All numbers apply for packages soldered directly into a PC board.
Note 5: Typical Values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
LM6152/LM6154
www.national.com 4
Typical Performance Characteristics
Supply Current vs.
Supply Voltage
DS012350-5
Offset Voltage vs.
Supply voltage
DS012350-6
Bias Current vs.
Supply voltage
DS012350-7
Bias Current vs. V
CM
DS012350-8
Bias Current vs. V
CM
DS012350-9
Bias Current vs. V
CM
DS012350-10
Output Voltage vs.
Source Current
DS012350-11
Output Voltage vs.
Source Current
DS012350-12
Output Voltage vs.
Source Current
DS012350-13
Output Voltage vs.
Sink Current
DS012350-14
Output Voltage vs.
Sink Current
DS012350-15
Output Voltage vs.
Sink Current
DS012350-16
LM6152/LM6154
www.national.com5
Typical Performance Characteristics (Continued)
Crosstalk (dB
vs. Frequency
DS012350-17
GBWP (@100 kHz)
vs. Supply Voltage
DS012350-18
Unity Gain Frequency
vs. Supply Voltage
for Various Loads
DS012350-19
CMRR
DS012350-20
Voltage Swing vs.
Frequency (C
L
= 100 pF)
DS012350-22
PSRR vs. Frequency
DS012350-23
Open Loop Gain/
Phase (V
S
= 5V)
DS012350-24
Open Loop Gain/
Phase (V
S
= 10V)
DS012350-25
Open Loop Gain/
Phase (V
S
= 24V)
DS012350-26
Noise Voltage
vs. Frequency
DS012350-27
Noise Current
vs. Frequency
DS012350-28
Voltage Error
vs. Settle Time
DS012350-29
LM6152/LM6154
www.national.com 6
Typical Performance
Characteristics (Continued)
Application Information
The LM6152/6154 is ideally suited for operation with about
10k(Feedback Resistor, R
F
) between the output and the
negative input terminal.
With R
F
set to this value, for most applications requiring a
close loop gain of 10 or less, an additional small compensa-
tion capacitor (C
F
) (see
Figure 1
) is recommended across R
F
in order to achieve a reasonable overshoot (10%) at the out-
put by compensating for stray capacitance across the inputs.
The optimum value for C
F
can best be established experi-
mentally with a trimmer cap in place since its value is depen-
dant on the supply voltage, output driving load, and the oper-
ating gain. Below, some typical values used in an inverting
configuration and driving a 10kload have been tabulated
for reference:
TABLE 1. Typical BW (−3 dB) at Various
Supply Voltage and Gains
V
S
Volts Gain C
F
pF BW (−3 dB)
MHz
3−1 5.6 4
−10 6.8 1.97
−100 None 0.797
24 −1 2.2 6.6
−10 4.7 2.2
−100 None 0.962
In the non-inverting configuration, the LM6152/6154 can be
used for closed loop gains of +2 and above. In this case,
also, the compensation capacitor (C
F
) is recommended
across R
F
(= 10 k) for gains of 10 or less.
Because of the unique structure of this amplifier, when used
at low closed loop gains, the realizable BW will be much less
than the GBW product would suggest.
The LM6152/6154 brings a new level of ease of use to op
amp system design.
The greater than rail-to-rail input voltage range eliminates
concern over exceeding the common-mode voltage range.
The rail-to-rail output swing provides the maximum possible
dynamic range at the output. This is particularly important
when operating on low supply voltages.
The high gain-bandwidth with low supply current opens new
battery powered applications where higher power consump-
tion previously reduced battery life to unacceptable levels.
The ability to drive large capacitive loads without oscillating
functional removes this common problem.
To take advantage of these features, some ideas should be
kept in mind.
The LM6152/6154, capacitive loads do not lead to oscilla-
tions, in all but the most extreme conditions, but they will re-
sult in reduced bandwidth. They also cause increased set-
tling time.
Unlike most bipolar op amps, the unique phase reversal
prevention/speed-up circuit in the input stage, caused the
slew rate to be very much a function of the input pulse ampli-
tude. This results in a 10 to 1 increase in slew rate when the
differential input signal increases. Large fast pulses will raise
the slew-rate to more than 30V/µs.
Total Harmonic Distortion
vs. Frequency
DS012350-31
DS012350-30
FIGURE 1. Typical Inverting Gain Circuit A
V
=−1
DS012350-21
FIGURE 2. Slew Rate vs. V
diff
LM6152/LM6154
www.national.com7
Application Information (Continued)
The speed-up action adds stability to the system when driv-
ing large capacitive loads.
A conventional op amp exhibits a fixed maximum slew-rate
even though the differential input voltage rises due to the
lagging output voltage. In the LM6152/6154, increasing lag
causes the differential input voltage to increase but as it
does, the increased slew-rate keeps the output following the
input much better. This effectively reduces phase lag. As a
result, the LM6152/6154 can drive capacitive loads as large
as 470 pF at gain of 2 and above, and not oscillate.
Capacitive loads decrease the phase margin of all op amps.
This can lead to overshoot, ringing and oscillation. This is
caused by the output resistance of the amplifier and the load
capacitance forming an R-C phase shift network. The
LM6152/6154 senses this phase shift and partly compen-
sates for this effect.
Ordering Information
Packaged Ordering Infomation NSC Drawing
Number Supplied As
8-Pin Dip LM6152ACN, LM5152BCN N08E Rails
8-Pin SOIC LM6152ACM, LM6152BCM M08A Rails
LM6152ACMX, LM6152BCMX M08A 2.5k Tape and Reel
14-Pin DIP LM6154ACN, LM6154BCN N14A Rails
14-Pin SOIC LM6154ACM, LM6154BCM M14A Rails
LM6154ACMX, LM6154BCMX M14A 2.5k Tape and Reel
LM6152/LM6154
www.national.com 8
Physical Dimensions inches (millimeters) unless otherwise noted
8-Lead (0.150”) Molded Small Outline Package, JEDEC
Ordering Number LM6152ACM or LM6152BCM
NSC Package Number M08A
14-Lead (0.150”) Molded Small Outline Package, JEDEC
Order Number LM6154BCM
NSC Package Number M14A
LM6152/LM6154
www.national.com9
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
8-Lead (0.300” Wide) Molded Dual-In-Line Package, JEDEC
Order Number LM6152ACN or LM6152BCN
NSC Package Number N08E
LM6152/LM6154
www.national.com 10
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: ap.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
14-Lead (0.300” Wide) Molded Dual-In-Line Package, JEDEC
Order Number LM6154ACN or LM6154BCN
NSC Package Number N14A
LM6152/LM6154Dual and Quad 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.