Approval Sheet Thick Film Chip Resistor RC series 1% & 5% YAGEO CORPORATION THICK FILM FACTORY Factory: No.11, Min Chuan Rd., Ta Sheh, Kaohsiung, Taiwan, R.O.C. Tel: 886-7-351-4117 Fax: 886-7-351-2075 Headquarters: 3F, No.233-1, Pao Chiao Rd., Shin Tien, Taipei, Taiwan, R.O.C. Tel: 886-2-2917-7555 Fax: 886-2-2917-4286 URL: www.yageo.com.tw RC Series Version 2001-8 Page-1 1. SUBJECT: This specification describes of RC series chip resistors made of YAGEO Corporation by thick film process. 2. PART NUMBER: Part number of the chip resistor is identified by the series, size, tolerance, packing style, temperature coefficient, special type and resistance value. Example RC 0603 Series Name (1) Size Size Code F R Resistance Tolerance Packing Style Chip: 0201 Power Chip: 1210 (2) Tolerance: F=1% (3) Packaging Type: 0402 2010 - 07 Temperature Coefficient of Resistance 0603 2512 0805 Special Type 10K Resistance Value 1206 J=5% RPaper Taping Reel. CBulk Cassette. KEmbossed Taping Reel (4) T.C.R: E=50ppm/ F=100ppm/ G=200ppm/ - = base on spec (5) Special Type: 07 7 inch Dia. Reel 1010 inch Dia. Reel 1313 inch Dia. Reel (6) Resistance Value: 1R10R100R10K100K330K1M......... 3. MARKING: Marking Explanation: (1) RC0805/RC1206/ RC1210/RC2010/RC2512 Either resistance in E-24 or E-96 series: 4 digits, first three digits are significant figures, fourth digit is number of zeros. Value =10K RC Series Version 2001-8 Page-2 (2) RC0603/RC0805/RC1206/RC1210/RC2010/RC2512 When resistance in E-24 series: 3 digits, first two digits are significant figures, third digit is number of zeros. Value =10K (3) RC0603 When resistance in E-96 series: 3 digits, use 0603 1% EIA-96 marking method. When 1% tol in E-24 series,protective layer distinquished with blue color Value =12.4 K EIA-96 MARKING Code R Value 01 100 02 102 03 105 04 107 05 110 06 113 07 115 08 118 09 121 10 124 11 127 12 130 Code R Value 13 133 14 137 15 140 16 143 17 147 18 150 19 154 20 158 21 162 22 165 23 169 24 174 Code R Value 25 178 26 182 27 187 28 191 29 196 30 200 31 205 32 210 33 215 34 221 35 226 36 232 Code R Value 37 237 38 243 39 249 40 255 41 261 42 267 43 274 44 280 45 287 46 294 47 301 48 309 Code R Value 49 316 50 324 51 332 52 340 53 348 54 357 55 365 56 374 57 383 58 392 59 402 60 412 Code R Value 61 422 62 432 63 442 64 453 55 464 66 475 67 487 68 499 69 511 70 523 71 536 72 549 Code R Value 73 562 74 576 75 590 76 604 77 619 78 634 79 649 80 665 81 681 82 698 83 715 84 732 Code R Value 85 750 86 768 87 787 88 806 89 825 90 845 91 866 92 887 93 909 94 931 95 953 96 976 This table shows the first two digits for the three-digit EIA-96 part marking scheme. The third character is a letter multiplier : X=10-1 Y=10-2 A=100 B=101 C=10 2 D=10 3 E=10 4 F=10 5 (4) RC0201/0402 RC0201/0402 no marking 0402 RC Series 0201 Version 2001-8 Page-3 4. POWER RATING (1) Rated Power at 70: RC0402=1/16W RC0603=1/10W RC0805=1/8W RC1206=1/4W RC2010=3/4W RC2512=1W RC0201=1/20W Rated Current(%) RC1210=1/3W Ambient Temperature( ) (2) Rated Voltage: The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: V (P X R) Where V Continuous rated DC or AC (rms) working voltage(V) P Rated power (W) R Resistance value () 5. ELECTRICAL CHARACTERISTICS Type RC0201 1/20 w Operating Temp. Range Maximum Working Voltage 15V Maximum Overload 50V Voltage Dielectric Withstanding 50V Voltage 10~1M (E-24) Resistance Range Zero Ohm Jumper<0.05 Temperature Coefficient RC Series RC0402 1/16 w RC0603 1/10 w RC0805 1/8 w 55 ~ 155 50V 50V 100V 100V 100V 100V 1~10M(E-24) 2.2~4.7M(E-96) Zero Ohm Jumper<0.05 1~22M(E-24) 1~4.7M(E-96) Zero Ohm Jumper<0.05 200ppm/ (10 R 100ppm/ (10 R 100ppm/ (10 R 10M) 10M) 1M) 200ppm/(1R<10) 200ppm/ (1 R<10 ,R>10M) Version 2001-8 150V 300V 300V 1~22M(E-24) 1~4..7M(E-96) Zero Ohm Jumper<0.05 100ppm/ (10 R 10M) 200ppm/ (1 R<10 ,R>10M) Page-4 Type RC1206 1/4 w RC1210 1/3 w Operating Temp. Range Maximum Working Voltage 200V Maximum Overload 400V Voltage Dielectric Withstanding 500V Voltage 1~22M(E-24) 1~4.7M(E-96) Resistance Range Zero Ohm Jumper<0.05 Temperature Coefficient 100ppm/ (10 R 10M) 200ppm/ (1 R<10 ,R>10M) RC2010 3/4 w RC2512 1w 55 ~ 155 200V 200V 400V 400V 500V 500V 1~22M(E-24) 1~4.7M(E-96) Zero Ohm Jumper<0.05 1~22M(E-24) 1~4.7M(E-96) Zero Ohm Jumper<0.05 1~22M(E-24) 1~4.7M(E-96) Zero Ohm Jumper<0.05 100ppm/ (10 R 10M) 200ppm/ (1 R<10 ,R>10M) 100ppm/ (10 R 10M) 200ppm/ (1 R<10 ,R>10M) 100ppm/ (10 R 10M) 200ppm/ (1 R<10 ,R>10M) 6. DIMENSIONS 200V 400V 500V 7. CONSTRUCTION Resistor(RuO2) Overcoat(Epoxy) Glass Alumina Substrate Internal Electrode (Ag-Pd) Secondery Electrode(Nickel Plated) External Electorde (Solder Plated) Unit: mm Type RC0201 RC0402 RC0603 RC0805 RC1206 RC1210 RC2010 RC2512 RC Series L 0.60 0.10 1.00 0.10 1.60 0.10 2.00 0.10 3.10 0.10 3.10 0.10 5.00 0.10 6.35 0.10 W 0.30 0.05 0.50 0.05 0.80 0.10 1.25 0.10 1.60 0.10 2.60 0.15 2.50 0.15 3.20 0.15 H 0.25 0.05 0.35 0.05 0.45 0.10 0.50 0.10 0.55 0.10 0.55 0.10 0.55 0.10 0.55 0.10 Version 2001-8 I1 0.15 0.10 0.20 0.10 0.25 0.15 0.35 0.20 0.45 0.20 0.50 0.20 0.60 0.20 0.60 0.20 I2 0.15 0.10 0.25 0.10 0.25 0.15 0.35 0.20 0.40 0.20 0.50 0.20 0.50 0.20 0.50 0.20 Page-5 8. ENVIRONMENTAL CHARACTERISTICS (1) Temperature Coefficient of Resistance (T.C.R.) Test Method: : Measure resistance at 25 or specified room temperature as R1, then measure at 55 or 155 respectively as R2. Determine the temperature coefficient of resistance from the following formula. R2R1 6 T.C.R. ------------ X 10 (P P M / ) R1 (t2t1) Where t125 or specified room temperature t255 or 155 test temperature R1resistance at reference temperature in ohms. R2resistance at test temperature in ohms. Acceptance Standard: (Refer to item 5) (2) Thermal Shock Test Method553, 2 minutes and 1552, 2 minutes as one cycle. After 5 cycles, the specimen shall be stabilized at room temp. for 1 hour minimum and then measure the resistance to determine R/R(%). Acceptance Standard(0.5%0.05) for 1% tol. (1%0.05) for 5% tol. (3) Low Temperature Operation +0 Test MethodPlace the specimen in a test chamber maintained at 65-5 . After one hour stabilization at this temperature, full rated working +5 +5 voltage shall be applied 45-0 minutes. Have15-0 minutes after remove the voltage, the specimen shall be removed from the chamber and stabilized at room temperature for 24 hrs. Measure the resistance to determine R/R(%). RC Series Version 2001-8 Page-6 Acceptance Standard: (0.5%0.05) for 1% tol . (1.0%0.05) for 5% tol. & No visible damage (4) Short Time Overload Test MethodApply 2.5 times of rated voltage but not exceeding the maximum overload voltage for 5 seconds. Have the specimen stabilized at room temperature for 30 minutes minimum. Measure the resistance to determine R/R(%). Acceptance Standard: (1.0%0.05) for 1% tol. (2.0%0.05) for 5% tol. & No visible damage (5) Insulation Resistance Test Method: Place the specimen in the jig and apply a rated continues overload voltage (R.C.O.V) for one minute as shown. Measure the insulation resistance. Type 0201 0402 0603 0805 1206 1210 2010 2512 Voltage 50V 100V 100V 300V 500V 500V 500V 500V Acceptance Standard10000M (6) Dielectric Withstand Voltage Test MethodPlace the specimen in the jig and apply a specified value continuous overload voltage as shown for one minute. Type Voltage RC Series 0201 0402 0603 0805 1206 1210 2010 2512 50V 100V 100V 300V 500V 500V 500V 500V Version 2001-8 Page-7 Acceptance StandardBreakdown voltagespecification and without open/short (7) Resistance to Soldering Heat Test MethodImmerse the specimen in the solder pot at 2605 for 101 seconds. Have the specimen stabilized at room temperature for 30 minutes minimum. Measure the resistance to determine R/R(%). Acceptance Standard(0.5%0.05) for 1% tol. (1.0%0.05) for 5% tol. & No visible damage (8) Moisture Resistance Test MethodPlace the specimen in the test chamber, and subjected to 42 damp heat cycles. Each one of which consists of the steps 1 to 7 as figure 1. The total length of test is 1000 hours. After the test, have the specimen stabilized at room temperature for 24 hours and measure the resistance to determine R/R(%). Acceptance Standard(0.5%0.05) for 1% tol. (2.0%0.05) for 5% tol. & no visible damage Fig. 1 RC Series Conditions of change of temperature Version 2001-8 Page-8 (9) Life Test MethodPlace the specimen in the oven at 702. Apply the rated voltage to the specimen at the 1.5 hours on and 0.5 hour off cycle. The total length of test is 1000 hours. After the test, have the specimen stabilized at room temperature for one hour minimum and measure the R/R(%). Acceptance Standard(1%0.05) for 1% tol (3%0.05) for 5% tol & no visible damage (10) Solderability Test MethodImmerse the specimen in the solder pot at 2305 for 5 sec. Acceptance StandardAt least 95% solder coverage on the termination. (11) Bending Strength Test MethodMount the specimen on a test board as shown in the figure. Slowly apply the force till the board is bent to specified for 51sec,and measure the R/R(%) at this position. Acceptance Standard: :(1.0%0.05) for 1% tol. (1.0%0.05) for 5% tol. & No visible damage Type Bent distance (d) 0201 0402 0603 0805 1206 1210 2010 2512 3mm 3mm 5mm 5mm 5mm 2mm 2mm 2mm Unit: mm RC Series Version 2001-8 Page-9 (12) Humidity (steady state) * Humidity (Steady State) Test MethodThe specimen shall be condition in a dry oven at TEMP. of 405 for a period of 24 Hr. The specimen shall be placed in a chamber and subjected to a relative humidity of 90 to 95 percent and a temperature of 402 for the length of time 10000+24 Hr. When length time subjected to a voltage cycle consisting of rated d.c. Voltage application of 1h 30 min and rest of 30 min repeatedly for one the test duration's given in 10000+24 h (42 day). Next, the specimen is taken out of the test chamber, allowed to stand at room temperature for approximately 24 h, measured for its resistance values again in accordance with 1-1. And then the variation in the resistance values taken before and after this test is calculated. 9. TAPING REEL Unitmm Style Packaging Tape width Paper 8mm Embossed 12mm RC0201/RC0402/0603 A +0 180 -3 B C W T 13.00.2 9.00.3 11.41 13.00.2 13.00.3 15.41 +1 60 -0 0805/1206/1210 +0 2010/2512 RC Series 180 -3 +1 60 Version 2001-8 -0 Page-10 10. (a)PAPER TAPING Unit: mm Dimension A B W E F P0 P1 P2 D0 T RC 0201 0.450.1 0.750.1 8.00.2 1.750.1 3.50.05 4.00.1 2.00.05 2.00.05 0.350.10 RC 0402 0.650.1 1.150.1 8.00.2 1.750.1 3.50.05 4.00.1 2.00.05 2.00.05 RC 0603 1.10.1 1.900.1 8.00.2 1.750.1 3.50.05 4.00.1 4.00.05 2.00.05 RC 0805 1.650.1 2.400.1 8.00.2 1.750.1 3.50.05 4.00.1 4.00.05 2.00.05 RC 1206 1.900.1 3.500.1 8.00.2 1.750.1 3.50.05 4.00.1 4.00.05 2.00.05 RC 1210 2.800.1 3.500.1 8.00.2 1.750.1 3.50.05 4.00.1 4.00.05 2.00.05 1.5+0.1 -0 1.5+0.1 -0 1.5+0.1 -0 1.5+0.1 -0 1.5+0.1 -0 1.5+0.1 -0 0.530.10 0.700.10 0.850.10 0.850.10 0.850.10 (b)EMBOSSED TAPING Feeding hole Chip pocket D0 D1 E A F W B T P1 Chip component P2 P0 Tape running direction Unit: mm Dimension A B W E F P0 P1 P2 D0 D0 T RC 2010 2.80.2 5.40.2 120.3 1.750.1 5.50.05 4.00.1 4.00.01 2.00.05 1.50.1 1.50.25 1.00.10 RC 2512 3.50.2 6.70.2 120.3 1.750.1 5.50.05 4.00.1 4.00.01 2.00.05 1.50.1 1.50.25 1.00.10 RC Series Version 2001-8 Page-11 11. PACKING METHODS PAPER CARRIER EMBOSSED CARRIER BULK CASSETTE Packing Style RC0201 RC0402 RC0603 RC0805 RC1206 RC1210 RC2010 RC2512 RC Series Paper Taping Reel (R) 7" (178mm) 10,000 10,000 5,000 5,000 5,000 5,000 --- 10" (254mm) 20,000 20,000 10,000 10,000 10,000 10,000 --- 13" (330mm) 40,000 40,000 20,000 20,000 20,000 20,000 --- Version 2001-8 Embossed Taping Reel(K) 7" (178mm) ------4,000 4,000 Bulk Cassette(C) 50,000 50,000 25,000 10,000 ----- Page-12