RC Series Versio n 20 01 -8 Page-1
Approval Sheet
Thick Film Chip Resistor
RC series
!
!!
!1% & !
!!
!5%
YAGEO CORPORATION
THICK FILM FACTORY
Factory: No.11, Min Chuan Rd., Ta Sheh, Kaohsiung, Taiwan, R.O.C.
Tel: 886-7-351-4117 Fax: 886-7 -35 1-2 07 5
Headquarters: 3F, No.233-1, Pao Chiao Rd., Shin Tien, Taipei, Taiwan,
R.O.C.
Tel: 886-2-2917-7555 Fax: 886-2 -29 17 -42 86
URL: www.yageo.com.tw
RC Series Versio n 20 01 -8 Page-2
1. SUBJECT: This specification describes of RC series chip resistors made of
YAGEO Corporation by thick film process.
2. PART NUMBER: Part number of the chip resistor is identified by the series, size,
tolerance, packing sty le, temperature coefficient, special type and
resistance value.
Example"
RC 0603 F R - 07 10K
Series Size Resistance Packing Temperature Special Resistance
Name Code Tolerance Style Coefficient Type Value
of Resistance
(1) Size Chip: 0201 0402 0603 0805 1206
Power Chip: 1210 2010 2512
(2) Tolerance: F=!1% J=!5%
(3) Packaging Type: R#Paper Taping Reel.
C
#Bulk Cassette.
K#Embossed Taping Reel
(4) T.C.R: E=!50ppm/$ F=!100ppm/$ G=!200ppm/$ - = base on spec
(5) Special Type: 07
# 7 inch Dia. Reel
10
#10 inch Dia. Reel
13
#13 inch Dia. Reel
(6) Resistance Value: 1R%10R%100R%10K%100K%330K%1M………
3. MARKING:
Marking Explanation:
(1) RC0805/RC1206/ RC1210/RC2010/RC2 512
Either resistance in E-24 or E-96 series: 4 digits, first three digits are significant
figures, fourth digit is number of zeros.
Value =10K&
RC Series Versio n 20 01 -8 Page-3
(2) RC0603/RC0805/RC1206/RC1210/RC2010/RC2512
When resistance in E-24 series: 3 digits, first two digits are significant figures,
third digit is number of zeros.
Value =10K&
(3) RC0603
When resistance in E-96 series: 3 digits, use 0603 !1% EIA-96 marking
method. W hen !1% tol in E-24 series,protective layer distinquished with
blue color
Value =12.4 K&
EIA-96 MARKING
Code R
Value Code R
Value Code R
Value Code R
Value Code R
Value Code R
Value Code R
Value Code R
Value
01 100 13 133 25 178 37 237 49 316 61 422 73 562 85 750
02 102 14 137 26 182 38 243 50 324 62 432 74 576 86 768
03 105 15 140 27 187 39 249 51 332 63 442 75 590 87 787
04 107 16 143 28 191 40 255 52 340 64 453 76 604 88 806
05 110 17 147 29 196 41 261 53 348 55 464 77 619 89 825
06 113 18 150 30 200 42 267 54 357 66 475 78 634 90 845
07 115 19 154 31 205 43 274 55 365 67 487 79 649 91 866
08 118 20 158 32 210 44 280 56 374 68 499 80 665 92 887
09 121 21 162 33 215 45 287 57 383 69 511 81 681 93 909
10 124 22 165 34 221 46 294 58 392 70 523 82 698 94 931
11 127 23 169 35 226 47 301 59 402 71 536 83 715 95 953
12 130 24 174 36 232 48 309 60 412 72 549 84 732 96 976
This table shows the first two di gits for the three-digit EIA-96 part marking scheme.
The third character is a letter multiplier :
X=10-1 Y=10-2 A=100 B=101 C=10 2 D=10 3 E=10
4 F=10 5
(4) RC0201/0402
RC0201/0402 no marking
0402 0201
RC Series Versio n 20 01 -8 Page-4
4. POWER RATING
(1) Rated Power at 70$: RC0402=1/16W RC0603=1/10W RC0805=1/8W RC1206=1/4W
RC1210=1/3W RC2010=3/4W RC2512=1W RC0201=1/20W
Rated Current(%)
Ambient Temperature(℃)
(2) Rated Voltage: The DC or AC (rms) continuous working voltage corresponding
to the rated power is determined by the following formula:
V
# '(P X R)
Where V
# Continuous rated DC or AC (rms) working voltage(V)
P
# Rated power (W)
R
# Resistance value (&)
5. ELECTRICAL CHARACTERISTICS
Type RC0201 1/20 w RC0402 1/16 w RC0603 1/10 w RC0805 1/8 w
Operating Temp. Range (55$ ~ )155$
Maximum Worki ng Volt age 15V 50V 50V 150V
Maximum Overload
Voltage 50V 100V 100V
300V
Dielectric Wi ths t andi ng
Voltage 50V 100V 100V
300V
Resistance Range 10&~1M& (E-24)
Zero Ohm Jumper<0.05&
1&~10M&(E-24)
2.2&~4.7M&(E-96)
Zero Ohm Jumper<0.05&
1&~22M&(E-24)
1&~4.7M&(E-96)
Zero Ohm Jumper<0.05&
1&~22M&(E-24)
1&~4..7M&(E-96)
Zero Ohm Jumper<0.05&
Temperature Coefficient
*200ppm/ $(10&+R+
1M&)
*100ppm/ $(10 &+R+
10M&)
*200ppm/$(1&+R<10&)
*100ppm/ $(10 &+R+
10M&)
*200ppm/ $(1 &+R<10
&,R>,0M&)
*100ppm/ $(10 &+R+
10M&)
*200ppm/ $(1 &+R<10
&,R>,0M&)
RC Series Versio n 20 01 -8 Page-5
Type RC1206 1/4 w RC1210 1/3 w RC2010 3/4 w RC2512 1w
Operating Temp. Range (55$ ~ )155$
Maximum Working Voltage 200V 200V 200V 200V
Maximum Overload
Voltage 400V 400V 400V 400V
Dielectric Wi ths t andi ng
Voltage 500V 500V 500V 500V
Resistance Range 1&~22M&(E-24)
1&~4.7M&(E-96)
Zero Ohm Jumper<0.05&
1&~22M&(E-24)
1&~4.7M&(E-96)
Zero Ohm Jumper<0.05&
1&~22M&(E-24)
1&~4.7M&(E-96)
Zero Ohm Jumper<0.05&
1&~22M&(E-24)
1&~4.7M&(E-96)
Zero Ohm Jumper<0.05&
Temperature Coefficient
*100ppm/ $(10&+R+
10M&)
*200ppm/ $(1 &+R<10
&,R>,0M&)
*100ppm/ $(10 &+R+
10M&)
*200ppm/ $(1 &+R<10
&,R>,0M&)
*100ppm/ $(10 &+R+
10M&)
*200ppm/ $(1 &+R<10
&,R>,0M&)
*100ppm/ $(10&+R+
10M&)
*200ppm/ $(1 &+R<10
&,R>,0M&)
6. DIMENSIONS 7. CONSTRUCTION
Unit: mm
Type L W H I1
I2
RC0201 0.60!
!!
!0.10 0.30!
!!
!0.05 0.25!
!!
!0.05 0.15!
!!
!0.10 0.15!
!!
!0.10
RC0402 1.00!
!!
!0.10 0.50!
!!
!0.05 0.35!
!!
!0.05 0.20!
!!
!0.10 0.25!
!!
!0.10
RC0603 1.60!
!!
!0.10 0.80!
!!
!0.10 0.45!
!!
!0.10 0.25!
!!
!0.15 0.25!
!!
!0.15
RC0805 2.00!
!!
!0.10 1.25!
!!
!0.10 0.50!
!!
!0.10 0.35!
!!
!0.20 0.35!
!!
!0.20
RC1206 3.10!
!!
!0.10 1.60!
!!
!0.10 0.55!
!!
!0.10 0.45!
!!
!0.20 0.40!
!!
!0.20
RC1210 3.10!
!!
!0.10 2.60!
!!
!0.15 0.55!
!!
!0.10 0.50!
!!
!0.20 0.50!
!!
!0.20
RC2010 5.00!
!!
!0.10 2.50!
!!
!0.15 0.55!
!!
!0.10 0.60!
!!
!0.20 0.50!
!!
!0.20
RC2512 6.35!
!!
!0.10 3.20!
!!
!0.15 0.55!
!!
!0.10 0.60!
!!
!0.20 0.50!
!!
!0.20
Resistor(RuO2)
Alumina Substrate
Internal Electrode (Ag-Pd)
Secondery Electrode(Nickel Plated)
External Electorde (Solder Plated)
Overcoat(Epoxy)
Glass
RC Series Versio n 20 01 -8 Page-6
8. ENVIRONMENTAL CHARACTERISTICS
(1) Temperature Coefficient of Resistance (T.C.R.)
Test Method:
::
: Measure resistance at )25$ or specifie d roo m tempera tur e as
R1, then measur e at (55$ or )155$ respectively as R2.
Determine the temperature coefficient of resistance from the
following formula.
R2(R1 `
T.C.R.
# ------------ X 106(PPM/$)
R
1 (t2(t1)
Where t1#)25$ or specified room temperature
t2#(55$ or )155$ test temperature
R1#resistance at reference t e mperature in ohms.
R2#resistance at test temperature in ohms.
Acceptance Standard: (Refer to item 5)
(2) Th ermal Shock
Test Method"(55!3$, 2 minutes an d )155!2$, 2 minutes as one cycle.
After 5 cycles, the specimen shall be stabilized at room temp. for
1 hour minimu m and the n me asure the resistance to determine
-R/R(%).
Acceptance Standard"!(0.5%)0.05&) for 1% tol.
!(1%)0.05&) for 5% tol.
(3) Low Temperature Operation
Test Method"Place the specimen in a test chamber maintained at (65 $.
After one hour stabilization at this temperature, full rated working
voltage shall b e ap plied 45 m inutes. Have15 minu te s after
remove the voltage, the specimen shall be removed from the
chamber and stabilized at room temperature for 24 hrs.
Measure the resistance to determine -R/R(%).
+5
+5+5
+5
-
--
-0
00
0
+0
+0+0
+0
-
--
-5
55
5
+5
+5+5
+5
-
--
-0
00
0
RC Series Versio n 20 01 -8 Page-7
Acceptance Standard: !(0.5%)0.05&) for 1% tol .
!(1.0%)0.05&) for 5% tol.
& No visible damage
(4) Short Time Overload
Test Method"Apply 2.5 times of rated voltage but not exceeding the maximum
overload voltage for 5 seconds. Have the specimen stabilized at
room temperature for 30 minutes minimum.
Measure the resistance to determine -R/R(%).
Acceptance Standard: !(1.0%)0.05&) for 1% tol.
!(2.0%)0.05&) for 5% tol.
& No visible damage
(5) Insulation Resistance
Test Method: Place the specimen in the jig and apply a rated continues
overload voltage (R.C.O.V) for one minute as shown.
Measure the insulation resistance.
Type 0201 0402 0603 0805 1206 1210 2010 2512
Voltage 50V 100V 100V 300V 500V 500V 500V 500V
Acceptance Standard".10000M&
(6) Dielectric Withstand Voltage
Test Method"Place the specimen in the jig and apply a specified value
continuous ove rload voltage as shown for one minute.
Type 0201 0402 0603 0805 1206 1210 2010 2512
Voltage 50V 100V 100V 300V 500V 500V 500V 500V
RC Series Versio n 20 01 -8 Page-8
Acceptance Standard"Breakdown voltage/specification and without
open/short
(7) Resistance to Soldering Heat
Test Method
"Immerse the specimen in the solder pot at 260!5$
for 10!1 seconds. Have the specimen stabilized at room
temperature for 30 minutes minimum.
Measure the resistance to determine -R/R(%).
Acceptance Standard"!(0.5%)0.05&) for 1% tol.
!(1.0%)0.05&) for 5% tol.
& No visible damage
(8) Moisture Resistance
Test Method
"Place the specimen in the tes t chamber, and subjected to 42
damp heat cycles. Each one of which consists of the steps 1 to 7
as figure 1. The total length of test is 1000 hours. After the test,
have the specimen stabilized at room temperature for 24 hours
and measure the resistance to determine -R/R(%).
Acceptance Standard"!(0.5%)0.05&) for 1% tol.
!(2.0%)0.05&) for 5% tol.
& no visible damage
Fig. 1 Conditions of change of temperature
RC Series Versio n 20 01 -8 Page-9
(9) Life
Test Method
"Place the specimen in the oven at 70!2$. Apply the rated voltage
to the specimen at the 1.5 hours on and 0.5 hour off cycle. The
total length of test is 1000 hours. After the test, have the specimen
st a bil ize d at ro o m t emper a t u r e for on e ho ur m inim u m and
measure the -R/R(%).
Acceptance Standard"!(1%)0.05&) for 1% tol
!(3%)0.05&) for 5% tol
& no visible damage
(10) Solderability
Test Method"Immerse the specimen in the solder pot at 230!5$ f o r 5 sec.
Acceptance Standard"At least 95% so lder coverage on the termination.
(11) Bending Strength
Test Meth od"Mount the specimen on a test board as shown in the figure.
Slowly apply the force till the board is bent to spec ified for
5
!1sec,and measure the -R/R(%) at this position.
Acceptance Standard:
::
:!(1.0%)0.05&) for 1% tol.
!(1.0%)0.05&) for 5% tol.
& No visible damage
Type 0201 0402 0603 0805 1206 1210 2010 2512
Bent distance
(d)
3mm
3mm
5mm
5mm
5mm
2mm
2mm
2mm
Unit: mm
RC Series Versio n 20 01 -8 Page-10
(12) Humidity (steady state)
• 英文參考資料：
Humidity (Steady State)
Test Method：The specimen shall be condition in a dry oven at TEMP. of 40±5℃
for a period of 24 Hr. The specimen shall be placed in a chamber and subjected to
a relative humidity of 90 to 95 percent and a temperature of 40℃±2℃ for the
length of time 1000 24
0
+Hr. Wh en leng th time subjected to a voltage cycle consisting
of rated d.c. Voltage application of 1h 30 min and rest of 30 min repeatedly for
one the test duration’s given in 1000 24
0
+h (42 day). Next, the specim en is taken ou t
of th e test chamber, allowed to stand at room temperature for approximately 24 h,
measured for its resistance values again in accordance with 1-1. And then the
variati on in the resistance values taken before and after this test is calculated.
9. TAPING REEL
Unit"mm
Style
Packaging Tape width ∅
∅∅
∅A ∅
∅∅
∅B ∅
∅∅
∅C W T
RC0201/RC0402/0603
0805/1206/1210 Paper 8mm
180+0
-3 60+1
-0 13.0!0.2 9.0!0.3 11.4!1
2010/2512 Embossed 12mm
180+0
-3 60+1
-0 13.0!0.2 13.0!0.3 15.4!1
RC Series Versio n 20 01 -8 Page-11
10. (a)PAPER TAPING
Unit: mm
Dimension A B W E F P0 P1 P2 0D0 T
RC 0201 0.45!0.1 0.75!0.1 8.0!0.2 1.75!0.1 3.5!0.05 4.0!0.1 2.0!0.05 2.0!0.05 1.5+0.1
-0
0.35!0.10
RC 0402 0.65!0.1 1.15!0.1 8.0!0.2 1.75!0.1 3.5!0.05 4.0!0.1 2.0!0.05 2.0!0.05 1.5+0.1
-0
0.53!0.10
RC 0603 1.1!0.1 1.90!0.1 8.0!0.2 1.75!0.1 3.5!0.05 4.0!0.1 4.0!0.05 2.0!0.05 1.5+0.1
-0
0.70!0.10
RC 0805 1.65!0.1 2.40!0.1 8.0!0.2 1.75!0.1 3.5!0.05 4.0!0.1 4.0!0.05 2.0!0.05 1.5+0.1
-0
0.85!0.10
RC 1206 1.90!0.1 3.50!0.1 8.0!0.2 1.75!0.1 3.5!0.05 4.0!0.1 4.0!0.05 2.0!0.05 1.5+0.1
-0
0.85!0.10
RC 1210 2.80!0.1 3.50!0.1 8.0!0.2 1.75!0.1 3.5!0.05 4.0!0.1 4.0!0.05 2.0!0.05 1.5+0.1
-0
0.85!0.10
(b)EMBOSSED TAPING
`
Unit: mm
Dimension A B W E F P0 P1 P2 0D0 0D0 T
RC 2010 2.8!0.2 5.4!0.2 12!0.3 1.75!0.1 5.5!0.05 4.0!0.1 4.0!0.01 2.0!0.05 1.5!0.1
1.5!0.25
1.0!0.10
RC 2512 3.5!0.2 6.7!0.2 12!0.3 1.75!0.1 5.5!0.05 4.0!0.1 4.0!0.01 2.0!0.05 1.5!0.1
1.5!0.25
1.0!0.10
T
Chip component
Feeding hole
D0
A
B
Chip pocket
P1P2 P0 Tape running direction
E
FW
D1
RC Series Versio n 20 01 -8 Page-12
11. PACKING METHODS
PAPER CARRIER
EMBOSSED CARRIER
BULK CASSETTE
Paper Taping Reel (R) Embossed
Taping Reel(K) Bulk
Cassette(C)
Packing
Style 7" (178mm) 10" (254mm) 13" (330mm) 7" (178mm)
RC0201 10,000 20,000 40,000 -- 50,000
RC0402 10,000 20,000 40,000 -- 50,000
RC0603 5,000 10,000 20,000 -- 25,000
RC0805 5,000 10,000 20,000 -- 10,000
RC1206 5,000 10,000 20,000 -- --
RC1210 5,000 10,000 20,000 -- --
RC2010 -- -- -- 4,000 --
RC2512 -- -- -- 4,000 --
