HELP3 AWC6311R Cellular CDMA 3.4 V/28 dBm Linear Power Amplifier Module TM PRELIMINARY DATA SHEET - Rev 1.3 FEATURES * InGaP HBT Technology * High Efficiency: 39 % @ +28 dBm output 20 % @ +16 dBm output * Low Quiescent Current: 8 mA * Low Leakage Current in Shutdown Mode: <1 A * Internal Voltage Regulation (no need for DC/DC Converter * Optimized for a 50 System * Low Profile Surface Mount Package: 1 mm * CDMA 1XRTT, 1xEV-DO Compliant * Pinout Enables Easy Phone Board Migration From 4 mm x 4 mm Package * RoHS Compliant Package, 250 oC MSL-3 * Suitable for new CDMA bands (806-849 MHz) AW C 631 1R M9 Package 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module APPLICATIONS * CDMA/EVDO Cell-band Wireless Handsets and Data Devices PRODUCT DESCRIPTION voltage regulation components. The 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 system. The AWC6311R meets the increasing demands for higher efficiency and smaller footprint in CDMA 1X handsets. The package pinout was chosen to enable handset manufacturers to switch from a 4 mm x 4 mm PA module with few layout changes while reducing board area requirements by 44 %. The AWC6311R uses ANADIGICS' exclusive InGaPPlusTM technology, which combines HBT and pHEMT devices on the same die, to enable state-of-the-art reliability, temperature stability, and ruggedness. The AWC6311R is part of ANADIGICS' High-Efficiencyat-Low-Power (HELPTM) family of CDMA power amplifiers, which deliver low quiescent currents and significantly greater efficiency without a costly external DAC or DC-DC converter. Through selectable bias modes, the AWC6311R achieves optimal efficiency across different output power levels, specifically at low- and mid-range power levels where the PA typically operates, thereby dramatically increasing handset talk-time and standby-time. Its built-in voltage regulator eliminates the need for external 10/2008 GND at slug (pad) VEN 8 GND 7 RFOUT RFIN 3 6 GND VBATT 4 5 VCC 1 VMODE 2 Bias Control Figure 1: Block Diagram AWC6311R GND VEN 1 8 GND VMODE 2 7 RFOUT RFIN 3 6 GND VBATT 4 5 VCC GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME 1 VEN 2 VMODE Mode Control 3 RFIN RF Input 4 VBATT Battery Voltage 5 VCC Supply Voltage 6 GND Ground 7 RFOUT RF Output 8 GND Ground DESCRIPTION PA Enable Voltage PRELIMINARY DATA SHEET - Rev 1.3 10/2008 AWC6311R ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC and VBATT) 0 +5 V Mode Control Voltage (VMODE) 0 +3.5 V Enable Voltage (VEN) 0 +3.5 V RF Input Power (PIN) - +10 dBm -40 +150 C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 824 - 849 MHz Supply Voltage (VCC and VBATT) +3.2 +3.4 +4.2 V Enable Voltage (VEN) +2.2 0 +2.4 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.2 0 +2.4 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) 27.5(1) 28.0 - dBm Case Temperature (TC) -30 - +85 C CDMA The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB. PRELIMINARY DATA SHEET - Rev 1.3 10/2008 3 AWC6311R Table 4: Electrical Specifications - CDMA Operation (TC = +25 C, VBATT = VCC = +3.4 V, VEN = +2.4 V, 50 system, IS-95 uplink waveform) PARAMETER MIN TYP MAX UNIT 27 15 29 16.5 32 19 dB - -51 -52 -47 -47 - -61 -62 -57 -57 dBc POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.4 V 36 17 39 20 - % POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.4 V Quiescent Current (Icq) - 8 13 mA VMODE = +2.4 V, Low Bias Enable Current - 0.5 0.8 mA through VEN pin, VMODE = +2.4 V Battery Current - 2.5 5 mA through VBATT pin, VMODE = +2.4 V Mode Control Current - <0.1 0.25 mA through VMODE pin, VMODE = +2.4 V Leakage Current - <1 5 A VCC = +4.2 V, VEN = 0 V, VMODE = 0 V - -134 -131 dBm/Hz - -137 -135 dBm/Hz - -158 - dBm/Hz Harmonics 2fo 3fo, 4fo - -40 -44 -30 -35 dBc Input Impedance - - 2:1 VSWR Gain Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Power-Added Efficiency (1) Noise in Receive Band Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure dBc - - -65 dBc 8:1 - - VSWR COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.4 V POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.4 V 869 MHz to 894 MHz: 16 dBm < POUT < 28dBm 869 MHz to 894 MHz: POUT < 16 dBm 1575 + 1.023 MHz CW Measurement POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions Notes: (1) PAE and ACP limit applies at 836.5 MHz. 4 PRELIMINARY DATA SHEET - Rev 1.3 10/2008 AWC6311R APPLICATION INFORMATION Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Table 5: Bias Control POUT LEVELS BIAS MODE VENABLE VMODE VCC VBATT CDMA - high power (High Bias Mode) > +16 dBm High +2.4 V 0V 3.2 - 4.2 V > 3.2 V CDMA - med/low power (Low Bias Mode) < +16 dBm Low +2.4 V +2.4 V 3.2 - 4.2 V > 3.2 V Optional lower VCC in low power mode < +7 dBm Low +2.4 V +2.4 V 1.5 V > 3.2 V - Shutdown 0V 0V 3.2 - 4.2 V > 3.2 V APPLICATION Shutdown VENABLE C6 1 F VMODE RFIN C7 68 pF* VBATT C1 10 F 1 VENABLE GND 8 2 VMODE RFOUT 7 3 RFIN GND 6 4 VBATT VCC 5 C4 68 pF GND at slug C5 68 pF RFOUT VCC C2 10 F Note: * This capacitor is only needed if a DC voltage is present on the RF input pin Figure 3: Application Circuit PRELIMINARY DATA SHEET - Rev 1.3 10/2008 5 AWC6311R PACKAGE OUTLINE Figure 4: M9 Package Outline - 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module 6311R LLLLNN BBBBCC Figure 5: Branding Specification 6 PRELIMINARY DATA SHEET - Rev 1.3 10/2008 AWC6311R COMPONENT PACKAGING Pin 1 Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7" PRELIMINARY DATA SHEET - Rev 1.3 10/2008 7 AWC6311R ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION COMPONENT PACKAGING AWC6311RM9Q7 -30 C to +85 C RoHS Compliant 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Tape and Reel, 2500 pieces per Reel AWC6311RM9P9 -30 C to +85 C RoHS Compliant 8 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Partial Tape and Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 PRELIMINARY DATA SHEET - Rev 1.3 10/2008