APA2065 Stereo 2.7-W Audio Power Amplifier (with DC_Volume Control) Features General Description * * * APA2065 is a monolithic integrated circuit, which provides precise DC volume control, and a stereo bridged audio power amplifiers capable of producing 2.7W(2.0W) into 3 with less than 10%(1.0%) THD+N. The attenuator range of the volume control in APA2065 is from 20dB (DC_Vol=0V) to -80dB (DC_Vol=3.54V) with 32 steps. The advantage of internal gain setting can be less components and PCB area. Both of the depop circuitry and the thermal shutdown protection circuitry are integrated in APA2065, that reduce pops and clicks noise during power up or shutdown mode operation. It also improves the power off pop noise and protects the chip from being destroyed by over temperature and short current failure. To simplify the audio system design, APA2065 combines a stereo bridge-tied loads (BTL) mode for speaker drive and a stereo single-end (SE) mode for headphone drive into a single chip, where both modes are easily switched by the SE/BTL input control pin signal. Low Operating Current with 14mA Improved Depop Circuitry to Eliminate Turn-on and Turn-off Transients in Outputs High PSRR * 32 Steps Volume Adjustable by DC Voltage with Hysteresis * 2W per Channel Output Power into 4 Load at 5V, BTL Mode * Two Output Modes Allowable with BTL and SE Modes Selected by SE/BTL pin * Low Current Consumption in Shutdown Mode (50A) * * * * Short Circuit Protection Power Off Depop Circuit Integration PDIP-16 & SOP-16 Packages Available Lead Free Available (RoHS Compliant) Applications * * NoteBook PC LCD Monitor or TV ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 1 www.anpec.com.tw APA2065 Ordering and Marking Information Package Code J : PDIP-16 K : SOP-16 Temp. Range I : - 40 to 85 C Handling Code TU : Tube TR : Tape & Reel TY : Tray Lead Free Code L : Lead Free Device Blank : Original Device APA2065 Lead Free Code Handling Code Temp. Range Package Code APA2065 XXXXX APA2065 J : XXXXX - Date Code APA2065 XXXXX APA2065 K : XXXXX - Date Code Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS and compatible with both SnPb and lead-free soldiering operations. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J STD-020C for MSL classification at lead-free peak reflow temperature. Block Diagram LOUT+ LIN- RINLOUT- Volume Control BYPASS BYPASS ROUT+ VOLUME SE/BTL SE/BTL ROUTSHUTDOWN Shutdown ckt VDD POW ER and Depop circuit Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 2 GND www.anpec.com.tw APA2065 Absolute Maximum Ratings (Over operating free-air temperature range unless otherwise noted.) Symbol VDD VIN TA TJ TSTG TS VESD PD Parameter Supply Voltage Range Input Voltage Range, SE/BTL, SHUTDOWN Operating Ambient Temperature Range Maximum Junction Temperature Rating Unit -0.3 to 6 V -0.3 to VDD+0.3 V C -40 to 85 Intermal Limited* Storage Temperature Range Soldering Temperature,10 seconds Electrostatic Discharge Power Dissipation C 1 -65 to +150 C 260 -3000 to 3000*2 -200 to 200*3 C V Intermal Limited Note: 1.APA2065 integrated internal thermal shutdown protection when junction temperature ramp up to 150C 2.Human body model: C=100pF, R=1500, 3 positives pulse plus 3 negative pulses 3.Machine model: C=200pF, L=0.5F, 3 positive pulses plus 3 negative pulses Recommended Operating Conditions Supply Voltage, VDD High level threshold voltage, VIH Low level threshold voltage, VIL SHUTDOWN Min. Max. Unit 4.5 2 5.5 V V 4 SE/BTL 1.0 SHUTDOWN 3 SE/BTL Common mode input voltage, VICM VDD-1.0 V V Thermal Characteristics Symbol Parameter R THJA Thermal Resistance from Junction to Ambient in Free Air Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 Value Unit PDIP-16 45 K/W SOP-16 60 K/W 3 www.anpec.com.tw APA2065 Electrical Characteristics VDD=5V, -20C<TA<85C (unless otherwise noted) Symbol VDD Parameter Supply Voltage IDD Supply Current ISD Supply Current in Shutdown Mode IIH IIL VOS Test Condition SE/BTL=0V SE/BTL=5V APA2065 Min. Typ. Max. 4.5 5.5 14 25 8.0 15 SE/BTL=5V SHUTDOWN=0V High input Current Low Input Current Output Differential Voltage Unit V mA 50 A 900 900 5 nA nA mV Operating Characteristics, BTL mode VDD=5V,TA=25C,RL=4, Gain=2V/V (unless otherwise noted) Symbol PO Parameter Maximum Output Power THD+N Total Harmonic Distortion Plus Noise PSRR Power Ripple Rejection Ratio Xtalk S/N Channel Separation Signal to Noise Ratio Test Condition THD=10%, RL=3, Fin=1kHz THD=10%, RL=4, Fin=1kHz THD=10%, RL=8, Fin=1kHz THD=1%, RL=3, Fin=1kHz THD=1%, RL=4, Fin=1kHz THD=0.5%, RL=8, Fin=1kHz PO=1.5W, RL=4, Fin=1kHz PO=1W, RL=8, Fin=1kHz VIN=0.1Vrms, RL=8, CB=1F, Fin=120Hz CB=1F, RL=8, Fin=1kHz PO=1.1W, RL=8, A_wieght APA2065 Unit Min. Typ. Max. 2.7 2.3 1.5 W 2.0 1.9 1 1.1 0.05 % 0.07 60 dB 90 95 dB dB Operating Characteristics, SE mode VDD=5V,TA=25C,RL=4, Gain=1V/V (unless otherwise noted) Symbol PO Parameter Maximum Output Power THD+N Total Harmonic Distortion Plus Noise PSRR Power Ripple Rejection Ratio Xtalk S/N Channel Separation Signal to Noise Ratio Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 Test Condition THD=10%, RL=8, Fin=1kHz THD=10%, RL=32, Fin=1kHz THD=1%, RL=8, Fin=1kHz THD=1%, RL=32, Fin=1kHz PO=250mW, RL=8, Fin=1kHz PO=75mW, RL=32, Fin=1kHz VIN=0.1Vrms, RL=8, CB=1F, Fin=120Hz CB=1F, RL=32, Fin=1kHz PO=75mW, SE, RL=32, A_wieght 4 APA2065 Unit Min. Typ. Max. 400 110 mW 320 90 0.08 % 0.08 48 dB 100 100 dB dB www.anpec.com.tw APA2065 Pin Description ROUT+ 1 16 VDD SHUTDOWN 2 15 ROUT- GND 1 VOLUME 2 RIN- 3 14 SE/BTL LOUT+ 3 GND 4 APA2065 PDIP-16 GND 5 VOLUME 6 13 GND LIN- 4 12 GND 1 1 B Y PASS V DD 5 10 LOUT- LOUT+ 7 9 LIN- 8 16 GND 15 RIN14 SHUTDOWN APA2065 SOP-16 13 ROUT+ 12 VDD LOUT- 6 11 ROUT- BYPASS 7 10 SE/BTL VDD GND 8 9 GND Pin Function Description Pin Name Config. GND Description Ground connection, Connected to thermal pad. VOLUME LOUT+ LINLOUTBYPASS I/P O/P I/P O/P SE/BTL I/P ROUT- O/P VDD ROUT+ SHUTDOWN RIN- O/P I/P I/P Input signal for internal volume gain setting. Left channel positive output in BTL mode and SE mode. Left channel input terminal Left channel negative output in BTL mode and high impedance in SE mode. Bias voltage generator Output mode control input, high for SE output mode and low for BTL mode. Right channel negative output in BTL mode and high impedance in SE mode. Supply voltage for internal circuit excepting power amplifier. Right channel positive output in BTL mode and SE mode. It will be into shutdown mode when pull low. Right channel input terminal Control Input Table SE/BTL X L H Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 SHUTDOWN L H H 5 Operating mode Shutdown mode BTL out SE out www.anpec.com.tw APA2065 Typical Application Circuit VDD 0.1 F VDD GND LOUT+ 1 F L-Ch input 100 F LIN- 220 F 1k 1 F RIN- R-Ch input VDD 4 LOUT- Volume Control 2.2 F 50k Control Pin Ring SE/BTL BYPASS BYPASS Tip Sleeve Headphone Jack ROUT+ VOLUME V DD 220 F 1k 100k SE/BTL SE/BTL 4 100k Shutdow n Signal SHUTDOWN ROUTShutdown ckt Volume Control Table_BTL Mode Supply Voltage Vdd=5V Gain(dB) 20 18 16 14 12 10 8 6 4 2 0 -2 -4 -6 -8 High(V) 0.12 0.23 0.34 0.46 0.57 0.69 0.80 0.91 1.03 1.14 1.25 1.37 1.48 1.59 1.71 Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 Low(V) 0.00 0.17 0.28 0.39 0.51 0.62 0.73 0.84 0.96 1.07 1.18 1.29 1.41 1.52 1.63 Hysteresis(mV) 52 51 50 49 47 46 45 44 43 41 40 39 38 37 6 Recommended Voltage(V) 0 0.20 0.31 0.43 0.54 0.65 0.77 0.88 0.99 1.10 1.22 1.33 1.44 1.56 1.67 www.anpec.com.tw APA2065 Volume Control Table_BTL Mode (Cont.) Supply Voltage Vdd=5V Gain(dB) -10 -12 -14 -16 -18 -20 -22 -24 -26 -28 -30 -32 -34 -36 -38 -40 -80 High(V) 1.82 1.93 2.05 2.16 2.28 2.39 2.50 2.62 2.73 2.84 2.96 3.07 3.18 3.30 3.41 3.52 5.00 Low(V) 1.74 1.85 1.97 2.08 2.19 2.30 2.42 2.53 2.64 2.75 2.87 2.98 3.09 3.20 3.32 3.43 3.54 Hysteresis(mV) 35 34 33 32 30 29 28 27 26 24 23 22 21 20 18 17 16 Recommended Voltage(V) 1.78 1.89 2.01 2.12 2.23 2.35 2.46 2.57 2.69 2.80 2.91 3.02 3.14 3.25 3.36 3.48 5 Typical Characteristics THD+N vs. Frequency THD+N vs. Output Power 10 10 VDD=5V RL=3 AV=2 BTL 1 0.1 THD+N (%) THD+N (%) VDD=5V RL=3 Po=1.75W BTL AV=10 AV=2 1 0.1 f=20kHz f=1kHz AV=5 f=20Hz 0.01 20 100 1k 0.01 10m 20k Rev. A.4 - Aug., 2005 1 2 3 Output Power (W) Frequency (Hz) Copyright ANPEC Electronics Corp. 100m 7 www.anpec.com.tw APA2065 Typical Characteristics THD+N vs. Frequency THD+N vs. Output Power 10 10 1 0.1 THD+N (%) THD+N (%) VDD=5V RL=4 Po=1.5W BTL AV=2 VDD=5V RL=4 AV=2 BTL 1 f=20kHz 0.1 f=1kHz AV=5 f=20Hz AV=10 0.01 20 5 0 100 200 500 1 k 2k 5k 0.01 100m 20k 200m Frequency (W) 10 1 THD+N (%) THD+N (%) VDD=5V RL=8 Po=1.0W BTL AV=2 f=20kHz 0.1 AV=10 f=20Hz 0.01 10m 20k Frequency (Hz) Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 2 1 f=1kHz 1k 1 VDD=5V RL=8 AV=2 BTL AV=5 100 3 THD+N vs. Output Power 10 0.01 20 2 Output Power (W) THD+N vs. Frequency 0.1 500m 800m 100m Output Power (W) 8 www.anpec.com.tw APA2065 Typical Characteristics (Cont.) THD+N vs. Output Power THD+N vs. Frequency 10 VDD=5V RL=8 Po=250mW SE VDD=5V RL=8 AV=2 BTL 1 1 THD+N (%) THD+N (%) 10 AV=1 AV=5 0.1 f=20kHz 0.1 f=20Hz AV=2.5 0.01 20 100 f=1kHz 1k 0.01 10m 20k 100m Frequency (Hz) Output Power (W) THD+N vs. Frequency THD+N vs. Output Power 10 10 VDD=5V RL=16 AV=1 BTL 1 AV=2 THD+N (%) THD+N (%) VDD=5V RL=16 Po=100mW SE 0.1 AV=1 1 f=20Hz f=1kHz 5 0 100 2 0 0 500 1k 2k 5k 0.01 10m 20k Frequency (Hz) Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 f=20kHz 0.1 AV=2.5 0.01 20 500m 100m 300m Output Power (W) 9 www.anpec.com.tw APA2065 Typical Characteristics (Cont.) THD+N vs. Output Power THD+N vs. Frequency 10 10 5 1 THD+N (%) THD+N (%) VDD=5V RL=32 Po=75mW SE AV=2.5 AV=1 0.1 VDD=5V RL=32 AV=1 BTL f=20kHz 1 f=20Hz 0.1 f=1kHz AV=5 0.01 20 100 1k 0.01 10m 20k Output Power (W) THD+N vs. Frequency THD+N vs. Output Swing 200m 10 VDD=5V RL=10 AV=1 SE VDD=5V RL=10 Vo=1VRMS SE 1 AV=2.5 THD+N (%) THD+N (%) 100m Frequency (Hz) 10 0.1 50m AV=1 1 0.1 f=20kHz f=1kHz f=20Hz AV=5 0.01 20 100 1k 0.01 100m 20k Frequency (Hz) Copyright ANPEC Electronics Corp. 500m 1 2 3 Output Swing (VRMS) 10 www.anpec.com.tw Rev. A.4 - Aug., 2005 Note:Dropout voltage definition:VIN-VOUT when VOUT is 2% below the value of VOUT for VIN= VOUT+1V APA2065 Typical Characteristics (Cont.) Crosstalk vs. Frequency Crosstalk vs. Frequency +0 +0 VDD=5V RL=32 -20 Po=75mW AV=1 SE Crosstalk (dB) VDD=5V RL=8 -20 Po=1.0W AV=2 BTL Crosstalk (dB) -40 -60 -80 R-ch to L-ch -120 20 100 1k -60 -80 R-ch to L-ch L-ch to R-ch L-ch to R-ch -100 -40 -100 -120 20 20k 100 Frequency (Hz) Noise Floor vs. Frequency 100u 100u VDD=5V RL=32 50u AV=1 50u SE No Filter Noise Floor (VRMS) Noise Floor (VRMS) 20k Frequency (Hz) Noise Floor vs. Frequency 20u A-Weight 10u 5u VDD=5V RL=8 AV=2 BTL 2u 1u 20 1k 100 1k Rev. A.4 - Aug., 2005 No Filter 10u A-Weight 5u 2u 1u 20 20k 100 1k 20k Frequency (Hz) Frequency (Hz) Copyright ANPEC Electronics Corp. 20u 11 www.anpec.com.tw APA2065 Typical Characteristics (Cont.) Noise Floor vs. Frequency Power Dissipation vs. Output Power 0.2 VDD=5V RL=10K 5 0 u AV=1 SE 0.18 Power Dissipation (W) Noise Floor (VRMS) 100u No Filter 20u 10u A-Weight 5u 2u 0.16 0.14 RL=8 0.12 0.1 RL=16 0.08 0.06 RL=32 0.04 VDD=5V AV=1 SE 0.02 1u 20 0 100 1k 20k 0 Frequency (Hz) Output Power (W) Power Dissipation vs. Output Power Supply Current vs. Supply Voltage 20 1.8 1.6 17.5 RL=3 1.4 Suuply Current (mA) Power Dissipation (W) 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 1.2 RL=4 1 0.8 0.6 RL=8 0.4 VDD=5V AV=2 BTL 0.2 15 BTL 12.5 10 SE 7.5 5 2.5 No Load 0 0 0.5 1 1.5 2 2.5 1 Output Power (W) Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 1.5 2 2.5 3 3.5 4 4.5 5 5.5 Supply Voltage (V) 12 www.anpec.com.tw APA2065 Typical Characteristics (Cont.) Output Power vs. Supply Voltage 1.8 Output Power (W) 1.6 160 RL=8 AV=2 BTL 140 Output Power (mW) 2.0 Output Power vs. Supply Voltage 1.4 THD+N=10% 1.2 1.0 0.8 THD+N=1% 0.6 RL=32 AV=1 SE 120 100 THD+N=10% 80 60 THD+N=1% 40 0.4 20 0.2 0 0 2.5 Output Power (W) 2.5 3.5 4 4.5 5 2.5 5.5 3.5 4 4.5 5 5.5 Supply Voltage (V) Output Power vs. Load Resistance Output Power vs. Load Resistance 0.7 VDD=5V AV=2 BTL 0.6 2 1.5 1 THD+N=10% 0.5 3 Supply Voltage (V) Output Power (W) 3 3 0.5 0.4 0.3 0.2 0.1 THD+N=1% 0 VDD=5V AV=1 SE THD+N=10% THD+N=1% 0 4 8 12 16 20 24 28 32 36 40 44 48 52 56 60 64 4 8 12 16 20 24 28 32 36 40 44 48 52 56 6064 Load Resistance () Load Resistance () Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 13 www.anpec.com.tw APA2065 Typical Characteristics (Cont.) Close Loop Response Close Loop Response +12 +6 +4 Loop Gain (dB) Loop Gain (dB) VDD=5V RL=8 +10 AV=2 BTL CO=330F +8 +6 AV=2 AV=5 AV=10 +4 +2 -0 20 VDD=5V RL=32 AV=1 SE CO=330F +2 +0 AV=1 AV=2.5 AV=5 -2 -4 100 1k -6 20 20k Frequency (Hz) 100 1k 20k Frequency (Hz) PSRR vs. Frequency Ripple Rejection Ratio (dB) +0 -20 TT VDD=5V Vin=100mVRMS RL=8 Cbypass=2.2F BTL -40 SE -60 -80 20 100 1k 20k Frequency (Hz) Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 14 www.anpec.com.tw APA2065 Application Descriptions BTL Operation Four times the output power same conditions. A BTL The APA2065 output stage (power amplifier) has two pairs of operational amplifiers internally, allowed for different amplifier configurations. configuration, such as the one used in APA2065, also creates a second advantage over SE amplifiers. Since the differential outputs, ROUT+, ROUT-, LOUT+, and LOUT-, are biased at half-supply, no need DC voltage exists across the load. This eliminates the need for an output coupling capacitor which is required in a single supply, SE configuration. OUT+ Volume Control amplifier output signal OP1 Single-Ended Operation RL Consider the single-supply SE configuration shown Application Circuit. A coupling capacitor is required to block the DC offset voltage from reaching the load. These capacitors can be quite large (approximately 33F to 1000F) so they tend to be expensive, occupy valuable PCB area, and have the additional drawback of limiting low-frequency performance of the system (refer to the Output Coupling Capacitor). The rules described still hold with the addition of the following relationship: 1 (1) 1 << 1 Cbypass x 125k RiCi RLCC OUT- Vbias Circuit OP2 Figure 1: APA2065 internal configuration (each channel) The power amplifier's OP1 gain is setting by internal unity-gain and input audio signal is come from internal volume control amplifier, while the second amplifier OP2 is internally fixed in a unity-gain, inverting configuration. Figure 1 shows that the output of OP1 is connected to the input to OP2, which results in the output signals of with both amplifiers with identical in magnitude, but out of phase 180. Consequently, the differential gain for each channel is 2 x (Gain of SE mode). Output SE/BTL Operation The ability of the APA2065 to easily switch between BTL and SE modes is one of its most important costs saving features. This feature eliminates the requirement for an additional headphone amplifier in applications where internal stereo speakers are driven in BTL mode but external headphone or speakers must be accommodated. By driving the load differentially through outputs OUT+ and OUT-, an amplifier configuration commonly referred to as bridged mode is established. BTL mode operation is different from the classical single-ended SE amplifier configuration where one side of its load is connected Internal to the APA2065, two separate amplifiers drive OUT+ and OUT- (see Figure 1). The SE/BTL input controls the operation of the follower amplifier that drives LOUT- and ROUT-. to ground. A BTL amplifier design has a few distinct advantages over the SE configuration, as it provides differential drive to the load, thus doubling the output swing for a specified supply voltage. Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 * When SE/BTL is held low, the OP2 is turn on and the APA2065 is in the BTL mode. 15 www.anpec.com.tw APA2065 Application Descriptions (Cont.) VOLUME input pin. The APA2065 volume control consists of 32 steps that are individually selected by a variable DC voltage level on the VOLUME control pin. The range of the steps, controlled by the DC voltage, are from 20dB to -80dB. Each gain step corresponds to a specific input voltage range, as shown in table. To minimize the effect of noise on the volume control pin, which can affect the selected gain level, hysteresis and clock delay are implemented. The amount of hysteresis corresponds to half of the step width, as shown in volume control graph. Output SE/BTL Operation (Cont.) * When SE/BTL is held high, the OP2 is in a high output impedance state, which configures the APA2065 as SE driver from OUT+. IDD is reduced by approximately one-half in SE mode. Control of the SE/BTL input can be a logic-level TTL source or a resistor divider network or the stereo headphone jack with switch pin as shown in Application Circuit. 1k Gan i _BTLmode VDD 100k APA2021volumecontrolcurve Forward Backward 20 Control Pin 16 Ring 12 8 SE/BTL 4 0 Tip -4 Sleeve -8 Headphone Jack -12 -16 Figure 2: SE/BTL input selection by phonejack plug -20 -24 In Figure 2, input SE/BTL operates as follows : -28 -32 When the phonejack plug is inserted, the 1k resistor is disconnected and the SE/BTL input is pulled high and enables the SE mode. When the input goes high, the OUT- amplifier is shutdown causing the speaker to mute. The OUT+ amplifier then drives through the output capacitor (CC) into the headphone jack. When there is no headphone plugged into the system, the contact pin of the headphone jack is connected from -36 -40 -44 0 0.6 0.8 1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6 2.8 3 3.2 3.4 3.6 3.8 (V) For highest accuracy, the voltage shown in the `recommended voltage'column of the table is used to select a desired gain. This recommended voltage is exactly halfway between the two nearest transitions. The gain levels are 2dB/step from 20dB to -40dB in 100k and 1k. BTL mode, and the last step at -80dB as mute mode. Resistor 1k then pulls low the SE/BTL pin, enabling the BTL function. Input Resistance, Ri The gain for each audio input of the APA2065 is set by the internal resistors (Ri and Rf) of volume control amplifier in inverting configuration. Volume Control Function APA2065 has an internal stereo volume control whose setting is a function of the DC voltage applied to the Rev. A.4 - Aug., 2005 0.4 Figure 3: Gain setting vs VOLUME pin voltage the signalpin, the voltage divider set up by resistors Copyright ANPEC Electronics Corp. 0.2 16 www.anpec.com.tw APA2065 Application Descriptions (Cont.) Input Resistance, Ri (Cont.) RF SE Gain = AV = Ri R F BTL Gain = -2 x Ri The value of Ci is important to consider as it directly affects the low frequency performance of the circuit. Consider the example where Ri is 10k and the specification calls for a flat bass response down to 100Hz. Equation is reconfigured as follow : (2) (3) BTL mode operation brings the factor of 2 in the gain equation due to the inverting amplifier mirroring the voltage swing across the load. For the varying gain setting, APA2065 generates each input resistance on figure 4. The input resistance will affect the low frequency performance of audio signal. The minmum input resistance is 10k when gain setting is 20dB and the resistance will ramp up when close loop gain below 20dB. The input resistance has wide variation (+/-10%) caused by process variation. Ci= (5) Consider to input resistance variation, the Ci is 0.16F so one would likely choose a value in the range of 0.22F to 1.0F. A further consideration for this capacitor is the leakage path from the input source through the input network (Ri+Rf, Ci) to the load. This leakage current creates a DC offset voltage at the input to the amplifier that reduces useful headroom, especially in high gain applications. For this reason a low-leakage tantalum or ceramic capacitor is the best choice. When polarized capacitors are used, the positive side of the capacitor should face the amplifier input in most applications as the DC level there is held at VDD/2, which is likely higher that the source DC level. Please note that it is important to confirm the capacitor polarity in the application. Ri vs Gain(BTL) Ri(k) 120 1 2x10kxf C 100 80 60 40 20 Effective Bypass Capacitor, Cbypass 0 -40 -30 -20 -10 0 10 As other power amplifiers, proper supply bypassing is critical for low noise performance and high power supply rejection. 20 Gain(dB) Figure 4: Input resistance vs Gain setting The capacitors located on both the bypass and power supply pins should be as close to the device as possible. The effect of a larger bypass capacitor will improve PSRR due to increased supply stability. Typical applications employ a 5V regulator with 1.0F and a 0.1F bypass capacitor as supply filtering. This does not eliminate the need for bypassing the supply nodes of the APA2065. The selection of bypass capacitors, especially Cbypass, is thus dependent upon desired PSRR requirements, click and pop performance. Input Capacitor, Ci In the typical application an input capacitor, Ci, is required to allow the amplifier to bias the input signal to the proper DC level for optimum operation. In this case, Ci and the minimum input impedance Ri (10k) form a high-pass filter with the corner frequency determined in the follow equation: FC(highpass)= 1 2x10kxCi Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 (4) 17 www.anpec.com.tw APA2065 Application Descriptions (Cont.) for power amplifier only and VDD is used for volume control amplifier and internal circuit excepting power amplifier. The APA2065 is a high-performance CMOS audio amplifier that requires adequate power supply decoupling to ensure the output total harmonic distortion (THD) is as low as possible. Power supply decoupling also prevents the oscillations causing by long lead length between the amplifier and the speaker. The optimum decoupling is achieved by using two different type capacitors that target on different type of noise on the power supply leads. Effective Bypass Capacitor, Cbypass (Cont.) To avoid start-up pop noise occurred, the bypass voltage should rise slower than the input bias voltage and the relationship shown in equation (6) should be maintained. 1 1 << (6) Cbypass x 125k 100k x Ci The bypass capacitor is fed thru from a 125k resistor inside the amplifier and the 100k is maximum input resistance of (Ri+ Rf). Bypass capacitor, Cb, values of 3.3F to 10F ceramic or tantalum low-ESR capacitors are recommended for the best THD and noise performance. For higher frequency transients, spikes, or digital hash on the line, a good low equivalent-series-resistance (ESR) ceramic capacitor, typically 0.1F placed as close as possible to the device VDD lead works best. For filtering lower-frequency noise signals, a large aluminum electrolytic capacitor of 10F or greater placed near the audio power amplifier is recommended. The bypass capacitance also effects to the start up time. It is determined in the following equation: Tstart up = 5 x (Cbypass x 125K) (7) Output Coupling Capacitor, Cc Optimizing Depop Circuitry In the typical single-supply SE configuration, an output coupling capacitor (Cc) is required to block the DC bias at the output of the amplifier thus preventing DC currents in the load. As with the input coupling capacitor, the output coupling capacitor and impedance of the load form a high-pass filter governed by equation. FC(highpass)= 1 2RLCC Circuitry has been included in the APA2065 to minimize the amount of popping noise at power-up and when coming out of shutdown mode. Popping occurs whenever a voltage step is applied to the speaker. In order to eliminate clicks and pops, all capacitors must be fully discharged before turn-on. Rapid on/off switching of the device or the shutdown function will cause the click and pop circuitry. (8) For example, a 330F capacitor with an 8 speaker The value of Ci will also affect turn-on pops (Refer to Effective Bypass Capacitance). The bypass voltage ramp up should be slower than input bias voltage. Although the bypass pin current source cannot be modified, the size of Cbypass can be changed to alter the device turn-on time and the amount of clicks and pops. By increasing the value of Cbypass, turn-on pop can be reduced. However, the tradeoff for using a larger bypass capacitor is to increase the turn-on time for this device. There is a linear relationship between the would attenuate low frequencies below 60.6Hz.The main disadvantage, from a performance standpoint, is the load impedance is typically small, which drives the low-frequency corner higher degrading the bass response. Large values of CC are required to pass low frequencies into the load. Power Supply Decoupling, Cs The APA2065 provides two independent power inputs for right channel and left channel used. PVDD is used Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 18 www.anpec.com.tw APA2065 Application Descriptions (Cont.) Optimizing Depop Circuitry (Cont.) volume control function abnormal when VOLUME control signal with spike or noise. APA2065 changes each step of volume gain after four clock cycles to make sure control signal ready. size of Cbypass and the turn-on time. In a SE configuration, the output coupling capacitor, CC, is of particular concern. BTL Amplifier Efficiency This capacitor discharges through the internal 10k resistors. Depending on the size of CC, the time constant can be relatively large. To reduce transients in SE mode, an external 1k resistor can be placed in parallel with the internal 10k resistor. The tradeoff for using this resistor is an increase in quiescent current. In the most cases, choosing a small value of Ci in the range of 0.33F to 1F, Cb being equal to 4.7F and an external 1k resistor should be placed in parallel with the internal 10k resistor should produce a virtually clickless and popless turn-on. An easy-to-use equation to calculate efficiency starts out as being equal to the ratio of power from the power supply to the power delivered to the load. The following equations are the basis for calculating amplifier efficiency. Efficiency = PO = VORMS x VORMS = VPxVP RL 2RL VORMS = VP 2 (10) PSUP = VDD x IDDAVG = VDD x 2VP RL Shutdown Function (11) Efficiency of a BTL configuration : In order to reduce power consumption while not in use, the APA2065 contains a shutdown pin to externally turn off the amplifier bias circuitry. This shutdown feature turns the amplifier off when a logic low is placed on the SHUTDOWN pin. The trigger point between a logic high and logic low level is typically 2.0V. It is best to switch between ground and the supply VDD PO VPxVP ) / (VDD x 2VP ) = VP =( 4VDD PSUP RL 2RL (12) Note that the efficiency of the amplifier is quite low for lower power levels and rises sharply as power to the load is increased resulting in a nearly flat internal power dissipation over the normal operating range. Note that the internal dissipation at full output power is less than in the half power range. Calculating the efficiency for a specific system is the key to proper power supply design. For a stereo 1W audio system with 8 loads and a 5V supply, the maximum draw on the power supply is almost 3W. to provide maximum device performance. By switching the SHUTDOWN pin to low, the amplifier enters a low-current state, I DD<50A. On normal operating, SHUTDOWN pin pull to high level to keeping the IC out of the shutdown mode. The SHUTDOWN pin should be tied to a definite voltage to avoid unwanted state changes. A final point to remember about linear amplifiers (either SE or BTL) is how to manipulate the terms in the efficiency equation to utmost advantage when possible. Note that in equation, V DD is in the Clock Generator APA2065 integrates a clock block 130kHz to avoid Rev. A.4 - Aug., 2005 (9) Where : A high gain amplifier intensifies the problem as the small delta in voltage is multiplied by the gain. So it is advantageous to use low-gain configurations. Copyright ANPEC Electronics Corp. PO PSUP 19 www.anpec.com.tw APA2065 Application Descriptions (Cont.) assuming a 5V-power supply and an 8 load, must not be greater than the power dissipation that results from the equation15: BTL Amplifier Efficiency (Cont.) denominator. This indicates that as VDD goes down, efficiency goes up. In other words, use the efficiency analysis to choose the correct supply voltage and speaker impedance for the application. PD,MAX= 31.25 0.16 2.00 0.55 0.50 47.62 0.21 2.83 0.55 1.00 66.67 0.30 4.00 0.5 1.25 78.13 0.32 4.47 0.35 (15) For DIP-16 package with thermal pad, the thermal resistance (JA) is equal to 45C/W. Po (W) Efficiency (%) IDD(A) VPP(V) PD (W) 0.25 TJ,MAX - TA JA Since the maximum junction temperature (TJ,MAX) of APA2065 is 150C and the ambient temperature (TA) is defined by the power system design, the maximum power dissipation which the IC package is able to handle can be obtained from equation15. Once the power dissipation is greater than the maximum limit (PD,MAX), either the supply voltage (VDD) must be decreased, the load impedance (RL) must be increased or the ambient temperature should be reduced. **High peak voltages cause the THD to increase. Table 1. Efficiency Vs Output Power in 5-V/8 BTL Systems Power Dissipation Whether the power amplifier is operated in BTL or SE modes, power dissipation is a major concern. In equation13 states the maximum power dissipation point for a SE mode operating at a given supply voltage and driving a specified load. VDD2 (13) SE mode : PD,MAX= 2 2 RL In BTL mode operation, the output voltage swing is doubled as in SE mode. Thus the maximum power dissipation point for a BTL mode operating at the same given conditions is 4 times as in SE mode. BTL mode : PD,MAX= 4VDD2 22RL (14) Since the APA2065 is a dual channel power amplifier, the maximum internal power dissipation is 2 times that both of equations depending on the mode of operation. Even with this substantial increase in power dissipation, the APA2065 does not require extra heatsink. The power dissipation from equation14, Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 20 www.anpec.com.tw APA2065 Packaging Information PDIP-16 pin ( Reference JEDEC Registration MS-001) D E c E1 eB s Q1 A2 A A1 A3 e b2 Dim A A1 A2 A3 b b2 b3 c D E E1 e eB Q1 s Millimeters Min. 0.38 3.17 2.92 0.36 1.14 0.76 0.20 18.632 Inches Max. 5.32 3.42 3.80 0.56 1.78 1.14 0.36 19.646 Min. 0.015 0.125 0.115 0.014 0.045 0.030 0.008 0.735 6.477 0.245 7.605BSC 6.223 8.492 1.397 0.58 3 Max. 0.210 0.135 0.150 0.022 0.070 0.045 0.014 0.775 0.300BSC 2.54BSC Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 b3 b 0.255 0.100BSC 9.506 1.651 0.84 8 21 0.335 0.055 0.023 3 0.375 0.065 0.033 8 www.anpec.com.tw APA2065 Package Information SO - 300mil ( Reference JEDEC Registration MS-013) D N H GAUGE PLANE E 1 2 3 A Millimeters 1 A1 B e L Variations- D Inches Variations- D Dim Min. Max. Variations Min. Max. Dim Min. Max. Variations Min. Max. A 2.35 2.65 SO-16 10.10 10.50 A 0.093 0.1043 SO-16 0.398 0.413 A1 0.10 0.30 SO-18 11.35 11.76 A1 0.004 0.0120 SO-18 0.447 0.463 B 0.33 0.51 SO-20 12.60 13 B 0.013 0.020 SO-20 0.496 0.512 D See variations SO-24 15.20 15.60 D See variations SO-24 0.599 0.614 E 7.40 SO-28 17.70 18.11 E SO-28 0.697 0.713 SO-14 8.80 9.20 e SO-14 0.347 0.362 e 7.60 1.27BSC 0.2914 0.2992 0.050BSC H 10 10.65 H 0.394 0.419 L 0.40 1.27 L 0.016 0.050 N See variations N See variations 0 1 1 8 Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 22 0 8 www.anpec.com.tw APA2065 Physical Specifications Terminal Material Lead Solderability Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb), 100%Sn Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3. Reflow Condition (IR/Convection or VPR Reflow) tp TP Critical Zone T L to T P Temperature Ramp-up TL tL Tsmax Tsmin Ramp-down ts Preheat 25 t 25 C to Peak Time Classificatin Reflow Profiles Profile Feature Average ramp-up rate (TL to TP) Preheat - Temperature Min (Tsmin) - Temperature Max (Tsmax) - Time (min to max) (ts) Time maintained above: - Temperature (T L) - Time (tL) Peak/Classificatioon Temperature (Tp) Time within 5C of actual Peak Temperature (tp) Ramp-down Rate Sn-Pb Eutectic Assembly Pb-Free Assembly 3C/second max. 3C/second max. 100C 150C 60-120 seconds 150C 200C 60-180 seconds 183C 60-150 seconds 217C 60-150 seconds See table 1 See table 2 10-30 seconds 20-40 seconds 6C/second max. 6C/second max. 6 minutes max. 8 minutes max. Time 25C to Peak Temperature Notes: All temperatures refer to topside of the package .Measured on the body surface. Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 23 www.anpec.com.tw APA2065 Classificatin Reflow Profiles(Cont.) Table 1. SnPb Entectic Process - Package Peak Reflow Temperature s Package Thickness Volume mm 3 Volume mm 3 <350 350 <2.5 mm 240 +0/-5C 225 +0/-5C 2.5 mm 225 +0/-5C 225 +0/-5C Table 2. Pb-free Process - Package Classification Reflow Temperatures Package Thickness Volume mm 3 Volume mm 3 Volume mm 3 <350 350-2000 >2000 <1.6 mm 260 +0C* 260 +0C* 260 +0C* 1.6 mm - 2.5 mm 260 +0C* 250 +0C* 245 +0C* 2.5 mm 250 +0C* 245 +0C* 245 +0C* *Tolerance: The device manufacturer/supplier shall assure process compatibility up to and including the stated classification temperature (this means Peak reflow temperature +0C. For example 260C+0C) at the rated MSL level. Reliability Test Program Test item SOLDERABILITY HOLT PCT TST ESD Latch-Up Method MIL-STD-883D-2003 MIL-STD-883D-1005.7 JESD-22-B,A102 MIL-STD-883D-1011.9 MIL-STD-883D-3015.7 JESD 78 Description 245C, 5 SEC 1000 Hrs Bias @125C 168 Hrs, 100%RH, 121C -65C~150C, 200 Cycles VHBM > 2KV, VMM > 200V 10ms, 1 tr > 100mA Carrier Tape & Reel Dimensions t E W D P Po P1 Bo F Ao Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 D1 24 Ko www.anpec.com.tw APA2065 Carrier Tape & Reel Dimensions(Cont.) T2 J C A B T1 Application SOP- 16 A B C J 330 1 100 +2 13+ 0.5 2 0.5 F D D1 Po 7.5 0.1 1.5 +0.1 T1 T2 16.4 +0.3 2.5 0.5 -0.2 P1 1.5+ 0.25 4.0 0.1 Ao W P E 16 0.2 12 0.1 1.750.1 Bo Ko t 2.0 0.1 10.9 0.1 10.8 0. 1 3.0 0.1 0.30.013 (mm) Cover Tape Dimensions Application SOP- 16 Carrier Width 24 Cover Tape Width 21.3 Devices Per Reel 1000 Customer Service Anpec Electronics Corp. Head Office : 5F, No. 2 Li-Hsin Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 7F, No. 137, Lane 235, Pac Chiao Rd., Hsin Tien City, Taipei Hsien, Taiwan, R. O. C. Tel : 886-2-89191368 Fax : 886-2-89191369 Copyright ANPEC Electronics Corp. Rev. A.4 - Aug., 2005 25 www.anpec.com.tw