Data SheetData Sheet
¤EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures
hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
Transformers
DC/DC converters
E 6.3
Series/Type: B78304B*A003
Date: October 2012
210/12
Please read Cautions and warnings and
Important notes at the end of this document.
Construction Dimensional drawing
■E 6.3 ferrite core
■Cover cap
■6 gullwing terminals
Features
■Very small size
■Low stray inductance,
low winding capacitance,
low DC resistance
Applications
■Pulse transformers
■Broadband transformers
■Drive transformers
for power semiconductors
■Low-power DC/DC converters
(B78304B1016A003)
Delivery mode and packing unit
■16-mm blister tape, reel 330 mm
■Packing unit: 900 pcs./reel
Pinning
Layout recommendation
Dimensions in mm
FIN0035-X
1
1
N
N
2
N
3
6
52
3 4
B78304B*A003DC/DC converters
E 6.3
DC/DC converters
310/12
Please read Cautions and warnings and
Important notes at the end of this document.
Technical data and measuring conditions
Characteristics and ordering codes
Main inductance L (1-6) 10 kHz, 10 mV
Inductance tolerance r55%
Stray inductance Lstray (1-6) 10 kHz, 10 mV, short 2-5, 3-4
Resistance RDC (1-6) Measured on 1-6
Capacitance Ci (1-2) 10 kHz, 100 mV
Resonance frequency fres Primary winding 1-6
Test voltage Vtest 50 Hz, 1 s
Operating temperature range –40 °C … +85 °C
Weight Approx. 0.6 g
L
mH
N1 : N2 : N3Lstray
PH
RDC
:
Ci
pF
B3dB
MHz
fres
MHz
Vtest
V AC
Ordering code
0.1 1:1:1 0.3 < 0.2 15 0.05 … 60 Approx. 9.0 500 B78304B1030A003
1.0 1:1:1 1.0 < 0.9 30 0.03 … 23 Approx. 4.0 500 B78304B1031A003
10.0 1:1:1 4.0 < 6.0 80 0.01 … 1.6 Approx. 0.2 500 B78304B1032A003
4.3 1: 0.21:0.21 20.0 < 6.0 — — > 0.6 500 B78304B1016A003
B78304B*A003DC/DC converters
E 6.3
DC/DC converters
410/12
Cautions and warnings
■Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
■The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.
Please read Cautions and warnings and
Important notes at the end of this document.
510/12
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of electronic components or
failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.
We also reserve the right to discontinue production and delivery of products.
Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.
