3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5 Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
Solder Tail
• End-to-endstackable
• Selectloadcapability
• Monoblockable
• ShoulderPin
Press Fit
• End-to-endstackable
• Earlymatelatebreakforhotswapping(press-t
EMLBadjustedbyapplicationtooling)
• Selectloadcapability
• Monoblockable
• Push-onshoulderpin
• Optionalfeed-throughtailforrearplug-upmidplane
applications
• AcceptsUniversalTooling
• RoHSCompliant.SeetheRegulatoryInformation
Appendix(RIA)inthe“RoHScompliance”section
ofwww.3Mconnector.comforcompliance
information(RIAE1&C1apply)
Date Modified: May 10, 2010 TS-1120-D
Sheet 1 of 4
Physical
Insulation:
Material: High Temp LCP
Flammability: UL 94V-0
Color: Beige
Contact:
Material: Phosphor Bronze
Plating:
Underplating: 50 µ" [1.27 µm] Nickel
Wiping Area: See Ordering Information
Solder Tails: See Ordering Information
Electrical
Current Rating: Signal: 1.5 A – All contacts simultaneously
Insulation Resistance: 103 MΩ
Withstanding Voltage: 1,000 V
AC
Environmental
Temperature Rating: -55°C to +125°C
Process Temperature Rating: 260°C (Prole per J-STD-020C)
Moisture Sensitivity Level: 1 (per J-STD-020C)
UL File No.: E68080
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5 Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
TS-1120-D
Sheet 2 of 4
Ordering Information
MP2 - HXXX - XXXX - S - XXXXX
Rows
4 = 4 Rows
5 = 5 Rows
H = Header
Loading Pattern
(See Table 2)
Plating Options
(See Table 4)
Tail Length
(See Table 3)
Pin Count
(See Table 1)
Termination Style
P = Press-Fit
S = Solder Tail
Shouldered Pins
Notes:
1. Refer to IEC 61076-4-104 Futurebus+® global standard.
2. “Press Fit” describes a contact tail having a compliant section designed to make a reliable electrical connection with a plated
through-hole (PTH) in a printed circuit board, typically a “back plane.”
POSITION X
POSITION 2
POSITION 1
ROW
C D E A
B
6.00
.236
"A"
15.80
.622
11.50
.453
1.40
.055
2.00
.079
17.80
.701
13.52
.532
17.00
.669
3.50
.138
MATING LENGTH
"B" TAIL LENGTH
"C"
2.00
.079
12.00
.472
14.00
.551
mm
[inch]
Tolerance Unless Noted
0 0.0 0.00
mm ±3 ±0.3 ±0.13
[ ] Dimensions for
Reference Only
FOR SPECIAL MONOBLOCKS
AND PIN ARRANGEMENTS
CONTACT 3M SALES
REPRESENTATIVE
4 ROW PRODUCT
5 ROW PRODUCT
SOLDER TAIL
PRODUCT
PRESS FIT
PRODUCT
PRESS FIT
PRODUCT
REAR
PLUG-UP
Contact 3M For Rear Plug-Up Option
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5 Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
TS-1120-D
Sheet 3 of 4
Table 2 - Mate Length vs. Loading Pattern
Loading
Pattern Code Description Mate length Row A Mate length Row B Mate length Row C Mate length Row D Mate length Row E
(5-Row Prod. Only)
1 All Positions Filled 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
2 All Positions Filled 6.50 [0.256] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
3 All Positions Filled 6.50 [0.256] 5.75 [0.226] 5.75 [0.226] 6.50 [0.256] 6.50 [0.256]
4 All Positions Filled 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256]
5 All Positions Filled 5.75 [0.226] 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226]
6 All Positions Filled 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226]
7 All Positions Filled 6.50 [0.256] 5.75 [0.226] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
8 All Positions Filled 6.50 [0.256] 5.00 [0.197] 6.50 [0.256] 6.50 [0.256] 6.50 [0.256]
9 All Positions Filled 5.00 [0.197] 6.50 [0.256] 5.00 [0.197] 5.00 [0.197] 5.00 [0.197]
A All Positions Filled 5.00 [0.197] 5.75 [0.226] 6.50 [0.256] 5.75 [0.226] 5.00 [0.197]
B All Positions Filled 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226] 5.75 [0.226]
C All Positions Filled 5.00 [0.197] 5.00 [0.197] 6.50 [0.256] 5.00 [0.197] 5.00 [0.197]
D All Positions Filled 5.75 [0.226] 5.75 [0.226] 7.25 [0.285] 5.75 [0.226] 5.75 [0.226]
E All Positions Filled 7.25 [0.285] 7.25 [0.285] 7.25 [0.285] 7.25 [0.285] 7.25 [0.285]
G All Positions Filled 7.25 [0.285] 5.75 [0.226] 5.75 [0.226] 5.00 [0.197] 5.00 [0.197]
H All Positions Filled 5.00 [0.197] 5.75 [0.226] 5.75 [0.226] 7.25 [0.285] 7.25 [0.285]
J All Positions Filled 8.00 [0.315] 8.00 [0.315] 8.00 [0.315] 8.00 [0.315] 8.00 [0.315]
K All Positions Filled 5.00 [0.197] 6.50 [0.256] 7.25 [0.285] 6.50 [0.256] 5.00 [0.197]
Table 1 - Connector & Row Lengths
Pin Count Dim. “A” mm
[inch]
Dim “C” mm
[inch] Rows
024 11.95 [0.471] 10.00 [0.394] 4
048 23.95 [0.943] 22.00 [0.866] 4
072 35.95 [1.415] 34.00 [1.339] 4
096 47.95 [1.889] 46.00 [1.811] 4
120 59.95 [2.36] 58.00 [2.283] 4
144 71.95 [2.833] 70.00 [2.756] 4
168 83.95 [3.305] 82.00 [3.228] 4
192 95.95 [3.778] 94.00 [3.701] 4
030 11.95 [0.471] 10.00 [0.394] 5
060 23.95 [0.943] 22.00 [0.866] 5
090 35.95 [1.415] 34.00 [1.339] 5
120 47.95 [1.888] 46.00 [1.811] 5
150 59.95 [2.361] 58.00 [2.283] 5
180 71.95 [2.833] 70.00 [2.756] 5
210 83.95 [3.305] 82.00 [3.228] 5
240 95.95 [3.778] 94.00 [3.701] 5
Table 4 - Plating Options
Plating
Suffix
Press-Fit
Tails*
Solder
Tails Plating Composition
TG30 (RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.76 μm [30 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
TR30 (RIA E2 &
C2 apply)
(RIA E3 &
C2 apply)
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
2.54 μm [100 μ”] Min. SnPb Tail Area
1.27 μm [50 μ”] Min. Ni all over
KR (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.76 μm [30 μ”] Min. Au Contact Area
2.54 μm [100 μ”] Min. Matt Whisker
Mitigating Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
LR (RIA E1 &
C1 apply)
(RIA E1 &
C1 apply)
0.08 μm [3 μ”] Min. Au Contact Area
0.67 μm [27 μ”] Min. PdNi Contact Area
2.54 μm [100 μ”] Min. Matt Whisker
Mitigating Sn Tail Area
1.27 μm [50 μ”] Min. Ni all over
KV
for rear
plug-up
only
(RIA E1 &
C1 apply)
0.76 μm [30 μ”] Min. Au Dual Contact Areas
0.10 μm [4 μ”] Min. Au Needle Eye
1.27 μm [50 μ”] Min. Ni all over
Table 3 - Tail Length Options
Plating Suffix
Dim. “B”
Solder Tail Press-Fit* Tail
1 1 4.60 [0.181]
3 2.72 [0.107]
*Compliant-Pin Tail
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ 2-FB Header
2 mm 4/5 Row, Vertical, Solder or Press-Fit Tail, Shouldered Pin MP2 Series
TS-1120-D
Sheet 4 of 4
RECOMMENDED 5 ROW SOLDER
TAIL PCB HOLE MOUNTING PATTERN
RECOMMENDED 4 ROW SOLDER
TAIL PCB HOLE MOUNTING PATTERN
RECOMMENDED 5 ROW PRESS-FIT
PCB HOLE MOUNTING PATTERN
RECOMMENDED 4 ROW PRESS-FIT
2.0 0
.07 9
Ø
1.50
+.10
-.00
.059
+.004
-.000
UNPLATED
12 .00
.47 2
2.00
.079
2.0 0
.07 9
16.00
.63 0 MIN
"D " PLAT ED TH RU HO LE
"C "
0.10
0.1 0
CENTER HOL ES OPTION AL
FOR 3M PRODUCT
12 .00
.472
12.0 0
.472
A1
6.00
.236
Ø
Ø
6.00
.236
2.00
.079
2.00
.079
"D" PLATED THRU HOLE
"C"
14.00
.551
2.00
.079
18.00
.709 MIN
1.50
+.10
-.00
.059
+.004
-.000
UNPLATED
0.10
0.10
A1
CENTER HOLES OPTIONAL
FOR 3M PRODUCT
12.00
.472
12.00
.472
Ø
Ø
Ø
1 6 . 0 0
. 6 3 0 M I N
" D " P L A T E D T H R U H O L E
0 . 1 0
Ø
"D " P L A T E D T H R U H O L E
1 8 .0 0
.7 0 9 M IN
0 .1 0
Ø
Table 5 – HOLE PLATING For TG30 and TR30 FINISHES ONLY
HOLE Finished Dia. MM [in] Cu Thickness [mm [in] SnPb Thickness microns [µ"]Drilled Hole Dia. mm [in]
“D” 0.65-0.80 [.0256-.0315] 0.025 [.001] min. 15 [600] max. 0.81-0.86 [.0319-.0339]
Table 6 – HOLE PLATING For KR, LR, and KV FINISHES ONLY
HOLE Finished Dia.
MM [in]
Immersion Matte
Sn Thickness
microns [µ”]
Electrolytic Au
Thickness
microns [µ"]
OSP ENTEK
Thickness
microns [µ”]
Drilled Hole
Dia. mm [in]
“D” 0.700-0.800
[.0276-.0315]
0.025-0.045
[0.001-0.002]
0.1 - 0.5
[4 - 20]
0.2 - 0.5
[8 - 20]
0.830-0.860 [.0330-.0340] or
0.85 mm [#66] TWIST DRILL
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
Please recycle. Printed in USA.
© 3M 2010. All rights reserved.
RIA-2217B-E
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3Mconnector.com 3M is a trademark of 3M Company.