SEMICONDUCTOR TECHNICAL DATA The MC10161 is designed to decode a three bit input word to a one of eight line output. The selected output will be low while all other outputs will be high. The enable inputs, when either or both are high, force all outputs high. The MC10161 is a true parallel decoder. No series gating is used internally, eliminating unequal delay times found in other decoders. This design provides the identical 4 ns delay from any address or enable input to any output. A complete mux/demux operation on 16 bits for data distribution is illustrated in Figure 1. This system, using the MC10136 control counters, has the capability of incrementing, decrementing or holding data channels. When both S0 and S1 are low, the index counters reset, thus initializing both the mux and demux units. The four binary outputs of the counter are buffered by the MC10101s to send twisted-pair select data to the multiplexer/demultiplexer to units. L SUFFIX CERAMIC PACKAGE CASE 620-10 P SUFFIX PLASTIC PACKAGE CASE 648-08 FN SUFFIX PLCC CASE 775-02 PD = 315 mW typ/pkg (No Load) tpd = 4.0 ns typ tr, tf = 2.0 ns typ (20%-80%) DIP PIN ASSIGNMENT LOGIC DIAGRAM E0 2 E1 15 6 Q0 VCC1 = PIN 1 VCC2 = PIN 16 VEE = PIN 8 5 Q1 VCC1 1 16 VCC2 E0 2 15 E1 4 Q2 Q3 3 14 C 3 Q3 Q2 4 13 Q4 13 Q4 Q1 5 12 Q5 12 Q5 Q0 6 11 Q6 A 7 10 Q7 VEE 8 9 B A 7 B 9 11 Q6 C 14 10 Q7 Pin assignment is for Dual-in-Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6-11 of the Motorola MECL Data Book (DL122/D). TRUTH TABLE ENABLE INPUTS INPUTS OUTPUTS E1 E0 C B A Q0 Q1 Q2 Q3 Q4 Q5 Q6 Q7 L L L L L L L L H X L L L L L L L L X H L L L L H H H H X X L L H H L L H H X X L H L H L H L H X X L H H H H H H H H H H L H H H H H H H H H H L H H H H H H H H H H L H H H H H H H H H H L H H H H H H H H H H L H H H H H H H H H H L H H H H H H H H H H L H H 3/93 Motorola, Inc. 1996 3-73 REV 5 MC10161 ELECTRICAL CHARACTERISTICS Test Limits Characteristic Power Supply Drain Current Input Current Symbol Pin Pi Under Test IE 8 IinH 14 IinL 14 0.5 -30C Min +25C Max Min 84 +85C Typ Max 61 76 350 Min Max Unit 84 mAdc 220 Adc 220 0.5 Adc 0.3 Output Voltage Logic 1 VOH 13 13 -1.060 -1.060 -0.890 -0.890 -0.960 -0.960 -0.810 -0.810 -0.890 -0.890 -0.700 -0.700 Vdc Output Voltage Logic 0 VOL 13 -1.890 -1.675 -1.850 -1.650 -1.825 -1.615 Vdc Threshold Voltage Logic 1 VOHA 13 13 -1.080 -1.080 Threshold Voltage Logic 0 VOLA 13 Switching Times -0.980 -0.980 -0.910 -0.910 -1.655 Vdc -1.630 -1.595 (50 Load) Propagation Delay Vdc ns t14+13- t14-13+ 13 13 1.5 1.5 6.2 6.2 1.5 1.5 4.0 4.0 6.0 6.0 1.5 1.5 6.4 6.4 Rise Time (20 to 80%) t13+ 13 1.0 3.3 1.1 2.0 3.3 1.1 3.5 Fall Time (20 to 80%) t13- 13 1.0 3.3 1.1 2.0 3.3 1.1 3.5 ELECTRICAL CHARACTERISTICS (continued) TEST VOLTAGE VALUES (Volts) Characteristic @ Test Temperature VIHmax VILmin VIHAmin VILAmax VEE -30C -0.890 -1.890 -1.205 -1.500 -5.2 +25C -0.810 -1.850 -1.105 -1.475 -5.2 +85C -0.700 -1.825 -1.035 -1.440 -5.2 Symbol Power Supply Drain Current Input Current Pin Under Test VIHmax TEST VOLTAGE APPLIED TO PINS LISTED BELOW VILmin VIHAmin VILAmax VEE (VCC) Gnd IE 8 2,7,9,14,15 8 1,16 IinH 14 14 8 1,16 IinL 14 8 1,16 14 Output Voltage Logic 1 VOH 13 13 2 15 8 8 1,16 1,16 Output Voltage Logic 0 VOL 13 14 8 1,16 Threshold Voltage Logic 1 VOHA 13 13 2 15 8 8 1,16 1,16 Threshold Voltage Logic 0 VOLA 13 14 8 1,16 Switching Times (50 Load) Propagation Delay Pulse In Pulse Out -3.2 V +2.0 V t14+13- t14-13+ 13 13 14 14 13 13 8 8 1,16 1,16 Rise Time (20 to 80%) t13+ 13 14 13 8 1,16 Fall Time (20 to 80%) t13- 13 14 13 8 1,16 Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50-ohm resistor to -2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the same manner. MOTOROLA 3-74 MECL Data DL122 -- Rev 6 MC10161 FIGURE 1 -- HIGH SPEED 16-BIT MULTIPLEXER/DEMULTIPLEXER Control Selection MC10101 MC10115 S0 S1 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 MC10136 CR A MC10101 B C D E1 C B A MC10164 E1 C B A MC10161 D0 E1 C B A MC10164 E1 C B A MC10161 D0 MC10115 S0 S0 S1 S1 MC10136 CR A CR B C D Start/Stop E0 15 14 13 12 11 10 9 8 MECL Data DL122 -- Rev 6 3-75 E0 7 6 5 4 3 2 1 0 MOTOROLA MC10161 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE C 0.007 (0.180) M T L-M B Y BRK -N- U N S 0.007 (0.180) M T L-M S S N S D -L- -M- Z W 20 D 1 V 0.010 (0.250) G1 X S T L-M N S S VIEW D-D A 0.007 (0.180) M T L-M S N S R 0.007 (0.180) M T L-M S N S Z C H -T- SEATING PLANE F VIEW S G1 0.010 (0.250) S T L-M S 0.007 (0.180) M T L-M S N S VIEW S S N S NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). MOTOROLA N K 0.004 (0.100) J S K1 E G 0.007 (0.180) M T L-M 3-76 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10 _ 0.310 0.330 0.040 --- MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10 _ 7.88 8.38 1.02 --- MECL Data DL122 -- Rev 6 MC10161 OUTLINE DIMENSIONS L SUFFIX CERAMIC DIP PACKAGE CASE 620-10 ISSUE V -A- 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. -B- C L DIM A B C D E F G H K L M N -T- K N SEATING PLANE M E F J G D 16 PL 0.25 (0.010) 16 PL 0.25 (0.010) M T A T B M -A- 9 1 8 B F C L S -T- SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 --- 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01 S P SUFFIX PLASTIC DIP PACKAGE CASE 648-08 ISSUE R 16 S INCHES MIN MAX 0.750 0.785 0.240 0.295 --- 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 T A M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303-675-2140 or 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 Mfax: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 MECL Data DL122 -- Rev 6 3-77 *MC10161/D* MC10161/D MOTOROLA