TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 NPN SILICON TRANSISTOR Qualified per MIL-PRF-19500/317 DEVICES LEVELS 2N2369A 2N2369AU 2N2369AUA 2N2369AUB 2N2369AUBC * 2N4449 JAN JANTX JANTXV JANS * Available to JANS quality level only. ABSOLUTE MAXIMUM RATINGS (TC = +25C unless otherwise noted) Parameters / Test Conditions Symbol Value Unit Collector-Emitter Voltage VCEO 15 Vdc Emitter-Base Voltage VEBO 4.5 Vdc Collector-Base Voltage VCBO 40 Vdc Collector-Emitter Voltage ICES 40 Total Power Dissipation @ TA = +25C 2N2369A; 2N4449 UA, UB, UBC U Operating & Storage Junction Temperature Range TO-18 (TO-206AA) 2N2369A Vdc (1) PT 0.36 0.36 (1, 3) 0.50 (2) W Top, Tstg -65 to +200 C Symbol Value Unit TO-46 (TO-206AB) 2N4449 THERMAL CHARACTERISTICS Parameters / Test Conditions Thermal Resistance, Ambient-to-Case 2N2369A; 2N4449 400 C/W RJA UA, UB, UBC 486 (3) U 350 Note: 1. Derate linearly 2.06 mW/C above TA = +25C. 2. Derate linearly 3.44 mW/C above TA = +54.5C. 3. Mounted on FR-4 PCB (1Oz. Cu) with contacts 20 mils larger than package pads. ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions OFF CHARACTERTICS Collector-Emitter Breakdown Voltage IC = 10mAdc Collector-Base Cutoff Current VCE = 20Vdc Symbol Min. V(BR)CEO 15 ICES Max. Unit SURFACE MOUNT UA SURFACE MOUNT UB & UBC (UBC = Ceramic Lid Version) Vdc 0.4 Adc SURFACE MOUNT U (Dual Transistor) T4-LDS-0057 Rev. 3 (110213) Page 1 of 8 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions OFF CHARACTERISTICS Emitter-Base Cutoff Current VEB = 4.5Vdc VEB = 4.0Vdc Collector- Base Cutoff Current VCB = 40Vdc VCB = 32Vdc ON CHARACTERISTICS (1) Forward-Current Transfer Ratio IC = 10mAdc, VCE = 0.35Vdc IC = 30mAdc, VCE = 0.4Vdc IC = 10mAdc, VCE = 1.0Vdc IC = 100mAdc, VCE = 1.0Vdc Collector-Emitter Saturation Voltage IC = 10mAdc, IB = 1.0mAdc IC = 30mAdc, IB = 3.0mAdc IC = 100mAdc, IB = 10mAdc Base-Emitter Saturation Voltage IC = 10mAdc, IB = 1.0mAdc IC = 30mAdc, IB = 3.0mAdc IC = 100mAdc, IB = 10mAdc Symbol Max. Unit IEBO 10 0.25 Adc ICBO 10 0.2 Adc hFE Min. 40 30 40 20 120 120 120 120 0.20 0.25 0.45 Vdc Vdc 0.80 0.85 0.90 1.20 Symbol Min. Max. Unit |hfe| 5.0 10 VCE(sat) 0.70 VBE(sat) DYNAMIC CHARACTERISTICS Parameters / Test Conditions Forward Current Transfer Ratio IC = 10mAdc, VCE = 10Vdc, f = 100MHz Output Capacitance VCB = 5.0Vdc, IE = 0, 100kHz f 1.0MHz Cobo 4.0 pF Input Capacitance VEB = 0.5Vdc, IC = 0, 100kHz f 1.0MHz Cibo 5.0 pF Max. Unit SWITCHING CHARACTERISTICS Parameters / Test Conditions Symbol Min. Turn-On Time IC = 10mAdc; IB1 = 3.0mAdc, IB2 = -1.5mAdc ton 12 s Turn-Off Time IC = 10mAdc; IB1 = 3.0mAdc, IB2 = -1.5mAdc toff 18 s Charge Storage Time IC = 10mAdc; IB1 = 10mAdc, IB2 = 10mAdc tS 13 s (1) Pulse Test: Pulse Width = 300s, Duty Cycle 2.0%. T4-LDS-0057 Rev. 3 (110213) Page 2 of 8 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Ltr CD CH HD LC LD LL LU L1 L2 P Q TL TW r Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .170 .210 4.32 5.33 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 .750 12.70 19.05 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .100 2.54 .030 0.76 .028 .048 0.71 1.22 .036 .046 0.91 1.17 .010 0.25 45 TP 45 TP Notes 6 7,8 7,8,13 7,8 7,8 7,8 5 5 3,4 3 10 6 NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Beyond r (radius) maximum, TH shall be held for a minimum length of .011 (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Body contour optional within zone defined by HD, CD, and Q. 6. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. 7. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8. All three leads. 9. The collector shall be internally connected to the case. 10. Dimension r (radius) applies to both inside corners of tab. 11. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 12. Lead 1 = emitter, lead 2 = base, lead 3 = collector. FIGURE 1. Physical dimensions TO-18 (2N2369A). T4-LDS-0057 Rev. 3 (110213) Page 3 of 8 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Ltr CD CH HD LC LD LL LU L1 L2 Q TL TW r Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .065 .085 1.65 2.16 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 1.750 12.70 44.45 .016 .019 0.41 0.48 .050 1.27 .250 6.35 .040 1.02 .028 .048 0.71 1.22 .036 .046 0.91 1.17 .010 0.25 45 TP 45 TP Notes 5 6 6 6 6 3 8 4 9 NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Symbol TL is measured from HD maximum. 4. Details of outline in this zone are optional. 5. Leads at gauge plane .054 inch (1.37 mm) +.001 inch (0.03 mm) -.000 inch (0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of TP relative to tab. Device may be measured by direct methods or by gauge. 6. Symbol LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. 7. Lead number three is electrically connected to case. 8. Beyond r maximum, TW shall be held for a minimum length of .011 inch (0.28 mm). 9. Symbol r applied to both inside corners of tab. 10. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 11. Lead 1 is emitter, lead 2 is base, and lead 3 is collector. FIGURE 2. Physical dimensions - TO-46 (2N4449). T4-LDS-0057 Rev. 3 (110213) Page 4 of 8 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Hatched areas on package denote metallized areas. 4. Lid material: Kovar. 5. Pad 1 = Base, Pad 2 = Emitter, Pad 3 = Collector, Pad 4 = Shielding connected to the lid. 6. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Ltr BH BL BW CL CW LL1 LL2 LS1 LS2 LW r r1 r2 Dimensions Inches Millimeters Min Max Min Max .046 .056 1.17 1.42 .115 .128 2.92 3.25 .085 .108 2.16 2.74 .128 3.25 .108 2.74 .022 .038 0.56 0.96 .017 .035 0.43 0.89 .036 .040 0.91 1.02 .071 .079 1.81 2.01 .016 .024 0.41 0.61 .008 .203 .012 .305 .022 .559 Notes FIGURE 3. Physical dimensions - surface mount (UB version, 2N2369AUB). T4-LDS-0057 Rev. 3 (110213) Page 5 of 8 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Symbol BH BL BW CL CW LL1 LL2 Dimensions Inches Millimeters Min Max Min Max .046 .071 1.17 1.80 .115 .128 2.92 3.25 .085 .108 2.16 2.74 .128 3.25 .108 2.74 .022 .038 0.56 0.96 .017 .035 0.43 0.89 Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Note Symbol LS1 LS2 LW r r1 r2 Dimensions Inches Millimeters Min Max Min Max .036 .040 0.91 1.02 .071 .079 1.81 2.01 .016 .024 0.41 0.61 .008 .203 .012 .305 .022 .559 Note NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Hatched areas on package denote metallized areas 4. Pad 1 = Base, Pad 2 = Emitter, Pad 3 = Collector, Pad 4 = connected to the lid braze ring. 5. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 4. Physical dimensions, surface mount (UBC version, ceramic lid). T4-LDS-0057 Rev. 3 (110213) Page 6 of 8 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Ltr. BL BL2 BW BW2 CH L3 LH LL1 LL2 LS LW LW2 Pin number. Transistor Dimensions Inches Millimeters Min Max Min Max .215 .225 5.46 5.71 .225 5.71 .145 .155 3.68 3.93 .155 3.93 .061 .075 1.55 1.90 .003 .007 0.08 0.18 .029 .042 0.74 1.07 .032 .048 0.81 1.22 .072 .088 1.83 2.23 .045 .055 1.14 1.39 .022 .028 0.56 0.71 .006 .022 0.15 0.56 1 Collector 2 Emitter 3 Base 4 N/C NOTES: 1. Dimensions are in inches. 2. Millimeters are given for general information only. 3. Dimension CH controls the overall package thickness. When a window lid is used, dimension CH must increase by a minimum of .010 inch (0.254 mm) and a maximum of .040 inch (1.020 mm). 4. The corner shape (square, notch, radius) may vary at the manufacturer's option, from that shown on the drawing. 5. Dimensions LW2 minimum and L3 minimum and the appropriate castellation length define an unobstructed threedimensional space traversing all of the ceramic layers in which a castellation was designed. (Castellations are required on the bottom two layers, optional on the top ceramic layer.) Dimension LW2 maximum and L3 maximum define the maximum width and depth of the castellation at any point on its surface. Measurement of these dimensions may be made prior to solder dipping. 6. The co-planarity deviation of all terminal contact points, as defined by the device seating plane, shall not exceed .006 inch (0.15mm) for solder dipped leadless chip carriers. 7. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 5. Physical dimensions - surface mount (UA version). T4-LDS-0057 Rev. 3 (110213) Page 7 of 8 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http://www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Ltr. BL BL2 BW BW2 CH L3 LH LL1 LL2 LS1 LS2 LW LW2 Pin number Transistor 1 Collector no. 1 2 Base no. 1 3 Base no. 2 Dimensions Inches Millimeters Min Max Min Max .240 .250 6.10 6.35 .250 6.35 .165 .175 4.19 4.44 .175 4.44 .066 .080 1.68 2.03 .003 .007 0.08 0.18 .026 .039 0.66 0.99 .060 .070 1.52 1.78 .082 .098 2.08 2.49 .095 .105 2.41 2.67 .045 .055 1.14 1.39 .022 .028 0.56 0.71 .006 .022 0.15 0.56 4 Collector no. 2 5 Emitter no. 2 6 Emitter no. 1 NOTES: 1. 1.Dimensions are in inches. 2. Millimeters are given for general information only. 3. Dimension CH controls the overall package thickness. When a window lid is used, dimension CH must increase by a minimum of .010 inch (0.254 mm) and a maximum of .040 inch (1.020 mm). 4. The corner shape (square, notch, radius) may vary at the manufacturer's option, from that shown on the drawing. 5. Dimensions LW2 minimum and L3 minimum and the appropriate castellation length define an unobstructed threedimensional space traversing all of the ceramic layers in which a castellation was designed. (Castellations are required on the bottom two layers, optional on the top ceramic layer.) Dimension LW2 maximum and L3 maximum define the maximum width and depth of the castellation at any point on its surface. Measurement of these dimensions may be made prior to solder dipping. 6. The co-planarity deviation of all terminal contact points, as defined by the device seating plane, shall not exceed .006 inch (0.15mm) for solder dipped leadless chip carriers. 7. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 6. Physical dimensions - surface mount (dual transistors, U version only, 2N2369AU). T4-LDS-0057 Rev. 3 (110213) Page 8 of 8