TAT7460 75 5V 50-2600 MHz RF Amplifier Applications Distribution Amplifiers Multi-Dwelling Units Drop Amplifiers Single-ended Gain Block FTTH Receivers SOT-89 Package Functional Block Diagram Product Features 50-2600 MHz bandwidth Low Noise Figure: 2.4 dB up to 1600 MHz Extremely Flat Gain Response Low Power Consumption: 100 mA with 5 V SOT-89 package General Description Pin Configuration The TAT7460 is a 75 Ohm RF Amplifier designed for use up to 2600 MHz, addressing the CATV and Satellite bands in a single part. The TAT7460 is fabricated using 6-inch GaAs pHEMT technology to optimize performance and cost. . Pin No. Label 1 2 3 4 RFin Gnd RFout/VDD Gnd Ordering Information Part No. Description TAT7460 TAT7460-EVB 75 pHEMT Amplifier 50-2600 MHz Evaluation Board Standard T/R size = 1000 pieces on a 7" reel. Datasheet: Rev C 02-04-13 (c) 2013 TriQuint - 1 of 8 - Disclaimer: Subject to change without notice TAT7460 75 5V 50-2600 MHz RF Amplifier Absolute Maximum Ratings Recommended Operating Conditions Parameter Parameter Rating Storage Temperature Device Voltage (VDD) -65 to 150C +10 V Operation of this device outside the parameter ranges given above may cause permanent damage. Device Voltage (VDD) Device Voltage (IDD) Case Temperature 6 Tj for >10 hours MTTF Min Typ Max Units 4.5 5.0 100 6.5 120 +85 +150 0 V mA C C Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Electrical Specifications Test conditions unless otherwise noted: VDD=+5 V, Temp= +25C, Freq.=50-2600 MHz Parameter Operational Frequency Range Gain Gain Flatness Input Return Loss Output Return Loss CSO CTB XMOD Output IP2 Output IP3 Output P1dB Noise Figure Device Current (IDD) Thermal Resistance, jc Datasheet: Rev C 02-04-13 (c) 2013 TriQuint Conditions Min 50 16.1 30 dBmV/channel at output 80 channels flat +56.2 +31.1 Pout = +5 dBm/tone f = 100 MHz 50-1600 MHz Junction to case - 2 of 8 - Typ Max 2600 16.5 +/- 0.5 18 18 -61 -72 -71 +58 +36 +20.5 2.5 100 51 120 Units MHz dB dB dB dB dBc dBc dBc dBm dBm dBm dB mA C/W Disclaimer: Subject to change without notice TAT7460 75 5V 50-2600 MHz RF Amplifier TAT7460-EVB Evaluation Board (50-2600 MHz) J3 R1 R1 C3 C3 J3 C2 L3 C7 C2 C7 L3 U1 C5 L2 C6 C1 C4 L1 U1 TAT7460 C1 L4 J1 RF Input L1 L4 bead L2 C4 C5 J1 J2 RFOutput J2 C6 Bill of Material - TAT7460-EVB Reference Des. U1 C1 C2, C3, C7 C4 C5 C6 L1 L2 L3 L4 R1 J1, J2 Value Description 75 pHEMT Amplifier 470 pF Ceramic Cap, 0603, 16 V, 5% 0.01 uF Ceramic Cap, 0603, X7R, 16 V, 5 % 390 pF Ceramic Cap, 0603, 16 V, 5% 0.7 pF Ceramic Cap, 0603, 50 V, 0.1 pF 0.5 pF Ceramic Cap, 0603, 50 V, 0.1 pF 3.6 nH Wirewound Ind, 0603, 5% 3.3 nH Wirewound Ind, 0603, 5% 880 nH Wirewound Ind, 1206, 5% Bead Ferrite Bead, 0402, 200 mA, 1.0 k 0 Thick Film Res, 1206 Connector F-Connector Datasheet: Rev C 02-04-13 (c) 2013 TriQuint - 3 of 8 - Manuf. Part Number TriQuint Various Various Various Various Various Various Various Various Murata Various Various TAT7460 BLM15AG102SN1 Disclaimer: Subject to change without notice TAT7460 75 5V 50-2600 MHz RF Amplifier Performance Plots - TAT7460-EVB Test conditions unless otherwise noted: VDD=+5 V, IDD=100 mA, Temp=+25C Noise Figure 4.0 19 3.5 18 3.0 NF (dB) S21 (dB) Gain 20 17 16 25 C 85 C 15 85 C 25 C 2.5 2.0 1.5 14 1.0 13 0.5 12 0.0 100 600 1100 1600 2100 2600 300 650 1000 Frequency (MHz) 0 0 -5 85 C 25 C -10 S22 (dB) S11 (dB) Output Return Loss -5 -15 -20 -25 25 C 85 C -15 -20 -25 -30 -30 -35 -35 -40 -40 100 600 1100 1600 2100 2600 100 600 Frequency (MHz) 1100 1600 2100 2600 Frequency (MHz) CSO CTB 30 dBmV/ch Output With 80 ch NTSC Flat Loading 65 30 dBmV/ch Output With 80 ch NTSC Flat Loading 90 80 CTB (dBc) 63 CSO (dBc) 1700 Frequency (MHz) Input Return Loss -10 1350 25 C 60 C 61 59 57 70 25 C 85 C 60 50 40 55 30 25 125 225 325 425 525 625 Frequency (MHz) Datasheet: Rev C 02-04-13 (c) 2013 TriQuint 25 125 225 325 425 525 625 Frequency (MHz) - 4 of 8 - Disclaimer: Subject to change without notice TAT7460 75 5V 50-2600 MHz RF Amplifier Performance Plots - TAT7460-EVB Test conditions unless otherwise noted: VDD=+5 V, IDD=100 mA, Temp=+25C XMOD 30 dBmV/ch Output With 80 ch NTSC Flat Loading 75 XMOD (dBc) 73 71 25 C 60 C 69 67 65 25 125 225 325 425 525 625 Frequency (MHz) Performance Plots Over Bias - TAT7460-EVB Test conditions unless otherwise noted: VDD=+4.5 to 6.5 V, IDD=100-120 mA, Temp=+25C Gain 800 20 140 700 19 120 600 100 500 400 Current Draw 18 S21 (dB) Power Draw 80 Power Draw (mW) Current Draw (mA) Current & Power 160 17 16 60 300 40 200 20 100 13 0 12 0 4.5 5 5.5 6 6.5 14 100 Device Bias (V) Datasheet: Rev C 02-04-13 (c) 2013 TriQuint 15 600 1100 1600 2100 2600 Frequency (MHz) - 5 of 8 - Disclaimer: Subject to change without notice TAT7460 75 5V 50-2600 MHz RF Amplifier Performance Plots Over Bias - TAT7460-EVB Test conditions unless otherwise noted: VDD=+4.5 to 6.5 V, IDD=100-120 mA, Temp=+25C CTB CTB (dBc) CSO (dBc) CSO 30dBmV/ch Output With 80 NTSC+70 QAM, Flat Loading 75 70 65 60 55 50 45 40 35 30 5.0V, 5.5V, 6.0V, 6.5V 4.5V 0 100 200 300 400 500 30dBmV/ch Output With 80 NTSC+70 QAM, Flat Loading 80 75 70 65 60 55 50 45 40 35 30 600 5.5V, 6.0V, 6.5V 5.0V 4.5V 0 100 Frequency (MHz) 200 XMOD (dBc) CIN (dB) 5.5V 5.0V, 6.0V, 6.5V 4.5V 0 100 200 300 400 500 600 Frequency (MHz) Datasheet: Rev C 02-04-13 (c) 2013 TriQuint 400 500 600 XMOD CIN 30dBmV/ch Output With 80 NTSC+70 QAM, Flat Loading 80 75 70 65 60 55 50 45 40 35 30 300 Frequency (MHz) 30dBmV/ch Output With 80 NTSC+70 QAM, Flat Loading 75 70 65 60 55 50 45 40 35 30 6.0V, 6.5V 5.5V 5.0V 4.5V 0 100 200 300 400 500 600 Frequency (MHz) - 6 of 8 - Disclaimer: Subject to change without notice TAT7460 75 5V 50-2600 MHz RF Amplifier Package Marking and Dimensions Marking: Part Number - TAT4760 Lot code - XXXXYYWW PCB Mounting Pattern Notes: 1. Ground / thermal vias are critical for the proper performance of this device. Vias should use a .35 mm (#80/.0135") diameter drill and have a final, plated thru diameter of .25 mm (.010"). 2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. 3. RF trace width depends upon the PC board material and construction. 4. All dimensions are in millimeters (inches). Angles are in degrees. Datasheet: Rev C 02-04-13 (c) 2013 TriQuint - 7 of 8 - Disclaimer: Subject to change without notice TAT7460 75 5V 50-2600 MHz RF Amplifier Product Compliance Information ESD Sensitivity Ratings Solderability Compatible with both lead-free (260C maximum reflow temperature) and tin/lead (245C maximum reflow temperature) soldering processes. Caution! ESD-Sensitive Device Contact plating: Annealed matte tin over copper. ESD Rating: Value: Test: Standard: Class 1A+ 450V Human Body Model (HBM) JEDEC Standard JESD22-A114 ESD Rating: Value: Test: Standard: Class IV Passes 1000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 RoHs Compliance This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). MSL Rating MSL Rating: Level 3 Test: 260C convection reflow Standard: JEDEC Standard IPC/JEDEC J-STD-020 This product also has the following attributes: Lead Free Halogen Free (Chlorine, Bromine) Antimony Free TBBP-A (C15H12Br402) Free PFOS Free SVHC Free Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Email: info-sales@tqs.com Tel: Fax: For technical questions and application information: +1.707.526.4498 +1.707.526.1485 Email: sjcapplications.engineering@tqs.com Important Notice The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or lifesustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Datasheet: Rev C 02-04-13 (c) 2013 TriQuint - 8 of 8 - Disclaimer: Subject to change without notice