MU12 SERIES Metallized Polyphenylene Sulfide (PPS) Wrap & Fill Tubular Configuration Specifically designed for low-drift, tight tolerance applications FEATURES - Direct Replacement For Polycarbonates - 1% Capacitance Tolerance - Manufactured To MIL Standards STANDARD CONFIGURATIONS - Wrap and Fill Tubular Configuration Rev. 2 Specification Summary Capacitance Range Capacitance shall be measured at 25 and at, or referred to, a frequency of 1 kHz. Capacitance Tolerance Standard tolerance is: 1%, 2%, 5%, 10%. Quality Control Capacitors are tested 100% for: o Capacitance o Tolerance o Dissipation Factor o Dielectric withstanding Voltage o Insulation resistance Capacitors can meet or exceed all requirements of MIL-PRF-55514. Operating Temperature Range -55C to +125C. Enclosure/ Construction Extended metallized PPS film (non-inductive). Voltage Rating DC working voltage ratings at +125 C, are 50VDC, 100VDC, 200VDC and 400VDC. Process and inspection data are maintained and available on special request. Environmental Parameter Vibration Immersion Shock Humidity Thermal Shock Life Method 204 104 213 106 107 108 Reference MIL-STD-202 Condition D B I A F Characteristics Insulation Resistance Temperature(C) 25 Megaohmsx 50,000 Microfarads 85 5,000 125 500 Insulation Resistance Capacitance Change Temperature(C) -55 PercentageChange +2.0 (typical) 25 0 85 1.0 125 2.0 CapacitanceChange Dissipation Factor When measured at 1 kHz, the dissipation factor shall not exceed 0.3% from +25 C to +125 C. Dielectric Strength Capacitors shall withstand a DC potential of 200% rated voltage for two (2) minutes without damage or breakdown. Test voltage must be applied and discharged through a resistance of 1 OHM per volt, minimum and at 25 C. Rev. 2 DIMENSIONAL EC Part Number MU12-102 MU12-122 MU12-152 MU12-182 MU12-222 MU12-272 MU12-332 MU12-392 MU12-472 MU12-562 MU12-682 MU12-822 MU12-103 MU12-123 MU12-153 MU12-183 MU12-223 MU12-273 MU12-333 MU12-393 MU12-473 MU12-563 MU12-683 MU12-823 MU12-104 MU12-124 MU12-154 MU12-184 MU12-224 MU12-274 MU12-334 MU12-394 MU12-474 MU12-564 MU12-684 MU12-824 MU12-105 MU12-125 MU12-155 MU12-185 MU12-205 MU12-255 MU12-305 MU12-355 MU12-405 MU12-455 MU12-505 MU12-605 MFD 0.0010 0.0012 0.0015 0.0018 0.0022 0.0027 0.0033 0.0039 0.0047 0.0056 0.0068 0.0082 0.0100 0.0120 0.0150 0.0180 0.0220 0.0270 0.0330 0.0390 0.0470 0.0560 0.0680 0.0820 0.1000 0.1200 0.1500 0.1800 0.2200 0.2700 0.3300 0.3900 0.4700 0.5600 0.6800 0.8200 1.0000 1.2000 1.5000 1.8000 2.0000 2.5000 3.0000 3.5000 4.0000 4.5000 5.0000 6.0000 DATA D 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.21 0.20 0.20 0.21 0.23 0.24 0.25 0.27 0.29 0.31 0.33 0.31 0.33 0.34 0.35 0.39 0.42 0.45 0.42 0.44 0.41 0.44 50 VDC L 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.73 0.73 0.83 0.83 0.83 0.83 0.83 1.00 1.00 1.22 1.22 G 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 22 D 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.21 0.23 0.20 0.21 0.22 0.24 0.25 0.27 0.29 0.31 0.34 0.31 0.34 0.34 0.36 0.39 0.42 0.42 0.45 0.43 0.47 0.50 0.53 0.57 0.60 0.63 0.67 100 VDC L 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.73 0.73 0.83 0.83 0.83 0.83 1.00 1.00 1.22 1.22 1.22 1.22 1.22 1.22 1.22 1.22 G 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 22 20 20 20 20 20 D 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.21 0.22 0.20 0.20 0.21 0.23 0.24 0.26 0.28 0.30 0.32 0.36 0.34 0.37 0.37 0.40 0.43 0.46 0.44 0.41 0.44 0.49 0.53 0.58 0.63 0.66 0.67 0.66 0.71 0.71 0.75 0.78 0.85 200 VDC L 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.73 0.73 0.83 0.83 0.83 0.83 1.00 1.22 1.22 1.22 1.22 1.22 1.22 1.22 1.50 1.75 1.75 1.95 1.95 1.95 1.95 G 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 22 22 20 20 20 20 20 20 20 20 20 20 20 D 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.21 0.22 0.20 0.20 0.20 0.22 0.23 0.25 0.27 0.29 0.32 0.34 0.32 0.35 0.38 0.37 0.40 0.43 0.46 0.45 0.49 0.46 0.50 0.55 0.59 0.64 0.69 0.70 0.68 0.71 0.77 0.85 0.92 0.97 - 400 VDC L 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.58 0.73 0.73 0.73 0.83 0.83 0.83 0.83 1.00 1.00 1.22 1.22 1.22 1.22 1.22 1.22 1.50 1.75 1.95 1.95 1.95 1.95 1.95 - G 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 22 20 20 20 20 20 20 20 20 20 20 20 20 - NOTE: All dimensionsare in inches. Rev. 2 EC Part Number MU12-805 MU12-106 MU12-126 MU12-156 MU12-186 MU12-206 MFD 8.0000 10.0000 12.0000 15.0000 18.0000 20.0000 D 0.50 0.55 0.59 0.65 0.63 0.66 50 VDC L 1.22 1.22 1.22 1.22 1.50 1.50 G 22 20 20 20 20 20 D 0.68 0.69 0.70 0.77 0.83 0.87 100 VDC L 1.50 1.75 1.95 1.95 1.95 1.95 G 20 20 20 20 20 20 D 0.97 1.07 - 200 VDC L 1.95 1.95 - G 20 20 - D - 400 VDC L - G - NOTE: All dimensionsare in inches. Mechanical Data Rev. 2 ADDITIONAL INFORMATION The MU12 SERIES is a new, versatile, PPS film capacitor, developed by Electronic Concepts as a direct replacement for polycarbonate capacitors -- to meet the ever changing, more demanding requirements of circuit designers. Although not required, it is built to MIL-PRF-55514 for reliability. The MU12 SERIES is specifically designed for low-drift, tight tolerance applications. This includes analog and timing circuits, high frequency uses and filter networks. There is capacitance tolerance as low as 1% for applications that require an exact capacitance match.Performance characteristics encompass low temperature coefficient, high insulation resistance, an operating temperature range of -55C to +125C, dissipation factor less than 0.3%, voltages from 50- 400VDC and excellent retrace. With the introduction of the MU12 SERIES, the designer can now build in more performance with greater reliability and operating protection. In addition, overall system cost savings can very often be realized. HOW TO ORDER TYPE MU12 Extended metallized PPS film (non-inductive) STYLE / VOLTAGE B B=50VDC, D=100VDC, F=200VDC, J=400VDC CAPACITANCE IN PICOFARADS The first two digits are significant, the third represents the number of zeros (e.g. 106 = 100,000 pfd = .1mfd) TOLERANCE 106 K K=10% G=2% J=5% F=1% Marking And Date Code All capacitors are marked with company initials "EC", corporate logo or EC trademark--in addition to type MU12, capacitance, tolerance, rated DC working voltage and date code. The first two digits of the date code represent the year, the second two digits the week, i.e., 0952 is the 52nd week of 2009, 0902 is the second week of 2009. Quality Asurance Major emphasis is placed on quality assurance. EC is an ISO 9001-2000 and AS9100:2004 Certified Company. Raw material inspection and the use of SPC manufacturing procedures assure the highest quality standards. Procedures are fully described in the EC Quality Control Manual. Electronic Concepts will continue to advance the state-of-the-art by utilizing leading edge technology, compact capacitor designs and establishing reliability procedures. Sales Offices United States Eastern: *Headquarters* P.O. Box 1278 Eatontown,NJ 07724 Tel: 732-542-7880 Fax: 732-542-0524 Central: Illinois 630-668-8747 Europe Ireland Electronic ConceptsEurope LTD IDA Estate, Oughterad Co. Galway, Ireland tel: +353-91-552385,552432 fax: +353-91-552387 email: sales@ecicaps.ie website:www.electronicconcepts.ie email: sales@ecicaps.com website:www.ecicaps.com Rev. 2