WRE_S - 3WR2 & WRF_S - 3WR2 Series 3WWIDE INPUT, ISOLATED & REGULATED DUAL/SINGLE OUTPUT DC-DC CONVERTER FEATURES Ultra-Miniature SIP Package 2:1 wide input voltage range Temperature range: -40C ~ +85C 3KVDC isolation Short circuit protection(automatic recovery) External On/Off control High power density APPLICATION Patent Protected RoHS The WRE_S-3WR2 & WRF_S-3WR2 Series are specially designed for applications where a wide range input voltage power supplies are isolated from the input power supply in a distributed power supply system on a circuit board. For these DC-DC converters, You can reduce the design point of failure and save the development of micro power supply`s manpower, material and time costs, also better ensure product quality stability, protect safety and reliability of the end of products. These products apply to where: 1) Input voltage range 2:1; 2) 3KVDC input and output isolation; 3) Regulated and low ripple noise is required. Such as: industrial control, telecommunication etc. PART NUMBER SYSTEM WRF1205S-3WR2 Rated Pow er Packag e St yle Output Vo ltage Input Volta ge Product Se ries SELECTION GUIDE Input Voltage(VDC) Model Nominal (Range) Max. Output Voltage (VDC) Output Current (mA) Input Current (mA)(Typ.) Max. @Max. @No Load Load Min. Reflected Ripple Current (mA, Typ.) Max. Capacitive Load (F) Efficiency (%, Typ.) @Max. Load WRE0505S-3WR2 5 250 13 676 1000 74 WRE0512S-3WR2 12 104 5 650 470 77 15 83 4 650 5 500 25 685 WRF0509S-3WR2 9 278 14 WRF0512S-3WR2 12 208 WRF0515S-3WR2 15 167 WRE1205S-3WR2 5 WRE1212S-3WR2 WRE1215S-3WR2 WRF1203S-3WR2 WRE0515S-3WR2 WRF0505S-3WR2 WRF1205S-3WR2 5 (4.5-9) 12 (9-18) 11 20 330 77 2200 73 676 1000 74 10 650 680 77 8 676 470 74 300 15 321 1000 78 12 125 6 317 470 79 15 100 5 313 330 80 3.3 758 38 278 2700 75 40 20 30 30 5 600 30 329 2200 76 WRF1209S-3WR2 9 333 17 317 1000 79 WRF1212S-3WR2 12 250 13 305 680 82 WRF1215S-3WR2 15 200 10 302 470 83 WRF1224S-3WR2 24 125 6 309 330 81 WRE2405S-3WR2 5 300 15 158 1000 79 WRE2409S-3WR2 9 167 8 155 680 81 WRE2412S-3WR2 12 125 6 151 470 83 WRE2415S-3WR2 15 100 5 151 330 83 3.3 758 38 141 2700 74 5 600 30 155 2200 81 WRF2409S-3WR2 9 333 17 151 1000 83 WRF2412S-3WR2 12 250 13 151 680 83 WRF2415S-3WR2 15 200 10 151 470 83 WRF2424S-3WR2 24 125 6 151 330 83 WRF2403S-3WR2 WRF2405S-3WR2 24 (18-36) 40 7 110 The copyright and authority for the interpretation of the products are reserved by MORNSUN WRE_S-3WR2 & WRF_S-3WR2 2013.07.26-A/3 Page 1 of 7 WRE4805S-3WR2 5 300 15 79 1000 79 WRE4812S-3WR2 12 125 6 76 470 82 WRE4815S-3WR2 15 100 5 76 330 82 WRF4803S-3WR2 3.3 758 38 70 2700 75 WRF4805S-3WR2 48 (36-75) 80 7 45 5 600 30 82 2200 76 WRF4812S-3WR2 12 250 13 78 680 80 WRF4815S-3WR2 15 200 10 75 470 84 WRF4824S-3WR2 24 125 6 77 330 82 Note:. Absolute maximum rating without damage on the converter, but it isn't recommended; . For dual output converter, the given value is the same for each output. INPUT SPECIFICATIONS Item Test Conditions Input Surge Voltage (1sec. max.) Start-up Voltage Min. Typ. Max. 5V input -0.7 -- 12 12V input -0.7 -- 25 24V input -0.7 -- 50 48V input -0.7 -- 100 5V input 3.5 4 4.5 12V input 4.5 8 9 24V input 11 16 18 48V input 24 33 36 Input Filter VDC C Filter Models ON Ctrl* Unit Models OFF Ctrl open or be insulated Connect high level voltage, and ensure the current into Ctrl to be 5-10mA Note: *Please refer to "DESIGN CONSIDERATIONS" as the direction for use of Ctrl. OUTPUT SPECIFICATIONS Item Test Conditions Min. Typ. Max. Output Voltage Accuracy 5% to 100% load -- 1 3 Input voltage range -- 1.5 5 Dual output, balanced loads -- 0.5 1 Line Regulation Full load, Input voltage from low to high -- 0.2 0.5 Load Regulation 5% to 100% load -- 0.6 1 -- 0.5 3 -- 2.5 5 % -- 0.02 0.03 %/C -- 30 45 -- 50 100 No-load Output Voltage Accuracy Output Voltage Balance Transient Recovery Time 25% load step change Transient Response Deviation Temperature coefficient Ripple 100% load 20MHz Bandwidth Noise Output Short Circuit Protection Unit % ms mVp-p Continuous, automatic recovery Note: .The max. no-load output voltage accuracy for WRF1203S-3WR2 and WRF4803S-3WR2 is 8%; . Ripple and noise tested with "parallel cable" method. See detailed operation instructions at DC-DC application notes; The max. output ripple for WRE2405S-3W R2 is 65mVp-p. COMMON SPECIFICATIONS Item Test Conditions Min. Typ. Max. Unit Isolation Voltage Input-Output, Tested for 1 minute, leakage current less than 1 mA 3000 -- -- VDC Isolation Resistance Input-Output, Test at 500VDC 1000 -- -- M Isolation Capacitance Input-Output, 100KHz/0.1V -- 30 50 pF -- 250 -- KHz 1000 -- -- K hours Switching Frequency(PFM Mode) 100% load, nominal input voltage MTBF MIL-HDBK-217F@25 Case Material PlasticUL94-V0 Weight -- 4.9 -- g ENVIRONMENTAL SPECIFICATIONS Item Test Conditions Min. Typ. Max. Storage Humidity Non condensing -- -- 95 % Operating Temperature Power derating (above85, see Figure 5) -40 -- 85 C The copyright and authority for the interpretation of the products are reserved by MORNSUN WRE_S-3WR2 & WRF_S-3WR2 2013.07.26-A/3 Unit Page 2 of 7 Storage Temperature -55 -- 125 Temp. rise at full load Ta=25C -- 25 -- Lead Temperature 1.5mm from case for 10 seconds -- -- 300 Cooling C Free air convection EMC SPECIFICATIONS EMI CE CISPR22/EN55022 CLASS BRecommended Circuit Refer to Figure1- or Figure 3 RE CISPR22/EN55022 CLASS B (Recommended Circuit Refer to Figure1- or Figure 3) ESD IEC/EN61000-4-2 Contact 4KV/ Air 8KV perf. Criteria B RS IEC/EN61000-4-3 10V/m perf. Criteria A IEC/EN61000-4-4 2KV Recommended Circuit Refer to Figure1- perf. Criteria B perf. Criteria B EFT IEC/EN61000-4-4 4KV Recommended Circuit Refer to Figure 3 Surge IEC/EN61000-4-5 2KV Recommended Circuit Refer to Figure1- or Figure 3 perf. Criteria B CS Voltage dips, short and interruptions immunity IEC/EN61000-4-6 3 Vr.m.s perf. Criteria A IEC/EN61000-4-29 0%-70% perf. Criteria B EMS EMC RECOMMENDED CIRCUIT FU S E LDM1 LDM2 Vin Vin + MO V GND TV S D1 C trl C1 C tr l C2 C0 + Vo R EUT LO AD Cd GND CY -Vo (0V) (Figure1) Recommended external circuit parameters: Model Vin:12V Vin5V FUSE Vin:24V Choose according to practical input current -S14K35 Vin:48V MOV -- LDM1 -- -- 56H 56H TVS SMCJ13A SMCJ28A SMCJ48A SMCJ90A C0 680F/16V 680F/25V 330F/50V 330F/100V C1 4.7F/50V 4.7F/100V LDM2 C2 12H 4.7F/50V CY 4.7F/100V 1nF/3KV D1 R S14K60 RB160M-60/1A Follows: Cd R= VC - VD - 1.0 - 300 IC 47nF/100V Note: 1.In Figure 1, part is EMS recommended external circuit, part is EMI recommended external circuit. Choose according to requirements; 2. VC is the voltage to GND from Ctrl, VD is the forward conduction voltage drop of D1,IC is the current through Ctrl pin which is normally 5-10mA, the external circuit of Ctrl is as shown in figure1-; 3. If there is no recommended parameters, the model no require the external component. EMC RECOMMENDED CIRCUIT PCB LAYOUT DUAL The copyright and authority for the interpretation of the products are reserved by MORNSUN WRE_S-3WR2 & WRF_S-3WR2 2013.07.26-A/3 Page 3 of 7 SINGLE (Figure 2) Note: The pad space between input and output GND (CY) must2mm. EMC MODULE APPLICATION CIRCUIT FU SE + C C t rl FT- A/B X1 D +Vo D1 EUT R C trl Cd -Vin +Vo Vin +Vin +Vin -Vin -Vo GN D Lo ad -Vo (0V) FT-A/BX1D is MORNSUN's EFT suppresser For Nominal Voltage<48V, C330uF/50V For Nominal Voltage =48V, C330uF/100V (Figure 3) EMC MODULE RECOMMENDED CIRCUIT PCB LAYOUT DUAL SINGLE (Figure 4) EMI TEST WAVEFORM (RECOMMENDED CIRCUIT REFER TO FIGURE 1-) WRE2415S-3WR2 CE(Class B, Positive line) WRE2415S-3WR2 CE(Class B, Negative line) The copyright and authority for the interpretation of the products are reserved by MORNSUN WRE_S-3WR2 & WRF_S-3WR2 2013.07.26-A/3 Page 4 of 7 WRF1205S-3WR2 CE(Class B, Negative line) WRF1205S-3WR2 CE(Class B, Positive line) PRODUCT TYPICAL PERFORMANCE CURVE Temperature Derating Graph O ut put Pow er P e rce nt(% ) Tolerance Envelope Graph 120 100 80 60 Safe Operating Area 40 20 0 -40 0 85 105 120 40 Ambient Temp.() Output Current Percent(%) (Figure 5) 100 95 90 85 80 75 70 65 60 55 50 Efficiency VS Output Load curve WRE2415S-3WR2 (Vin=Vin-nominal) Efficiency(%) Efficiency(%) Efficiency VS Input Voltage curve (Full Load) WRE2415S-3WR2 100 90 80 70 60 50 40 30 20 10 0 10 18 20 22 24 26 28 30 32 34 20 Efficiency VS Input Voltage curve (Full Load) WRF1205S-3WR2 Efficiency(%) Efficiency(%) 90 85 80 75 70 65 60 55 10 11 12 13 14 15 Input Voltage(V) 50 60 70 80 90 100 Efficiency VS Output Load curve WRF1205S-3WR2 (Vin=Vin-nominal) 100 95 9 40 Total Output Current (%) Input Voltage(V) 50 30 36 16 17 18 100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 50 60 70 80 90 100 Total Output Current (% ) The copyright and authority for the interpretation of the products are reserved by MORNSUN WRE_S-3WR2 & WRF_S-3WR2 2013.07.26-A/3 Page 5 of 7 OUTLINE DIMENSIONS,RECOMMENDED FOOTPRINT & PACKAGING TEST CONFIGURATIONS Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with an inductor Lin and Capacitor Cin to simulate the source impedance. Oscilloscope Lin Cin Lin(4.7H) Current Probe DC DC Load Cin(220F, ESR < 1.0 at 100 KHz) DESIGN CONSIDERATIONS 1) Requirement on output load To ensure this module can operate efficiently and reliably, during operation, the minimum output load could not be less than 5% of the full load, otherwise output ripple maybe increase dramatically. If the actual output power is very small, please connect a resistor with proper resistance at the output end in parallel to increase the load, suppose to use the resistance of 5% rated power, or use our company's products with a lower rated output power. 2) Recommended circuit All the WRE_S-3WR2 & WRF_S-3WR2 series have been tested according to the following recommended test circuit before leaving the factory (see Figure 6). If you want to further decrease the input/output ripple, you can increase a capacitance-values properly or choose capacitors with low ESR. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor must be less than the Max. Capacitive Load. General: Cin1: 5V&12V 100F 24V&48V 10F Cin2: 5V&12V 47F 24V&48V 1F Lin: 4.7H~12H Cs: 10F~22F Cout: 100F(Typ.) Lout: 2.2H~10H Cd: 47nF/100V Single output V in L in 2 Dual output 6 +Vo L in 2 Vin C i n1 Ci n2 6 Cs 1 D1 I c R 3 7 7 C ou t 0V Vc Lo ut 1 G ND Cd D1 Ic R +V o Cou t 8 G ND Cd Vc Lout Cin 1 C in2 3 8 0V Cou t -V o (Figure 6) The copyright and authority for the interpretation of the products are reserved by MORNSUN WRE_S-3WR2 & WRF_S-3WR2 2013.07.26-A/3 Page 6 of 7 3) Ctrl Terminal When open or high impedance, the converter works well; When this pin is `high', the converter shut down. It should be note that the input current should be between 5-10mA, exceeding the maximum 20mA will cause permanent damage to the converter. The value of R can be derived as follows: R= VC - VD - 1.0 - 300 IC For Detailed param eter, please refer to "EMC RECOMMENDED CIRCUIT". Input Current(A) 4) Input current When it is used in unregulated power supply, be sure that the fluctuating range of the power supply and the rippled voltage do not exceed the module standard. Input current of power supply should afford the flash startup average current of this kind of DC/DC module (Figure 7). General: Vin:5V Iave =1110mA Vin:12V Iave =640mA Vin:24V Iave =325mA Vin:48V Iave =160mA Iave Input Voltage Range Input Voltage (V) (Figure 7) 5) It is not recommended to increase the output power capability by connecting two or more converters in parallel. The product is not hot-swappable Note: 1. Min. load shouldn't be less than 5%, otherwise ripple maybe increased dramatically. If the product operates under min. load, it may not be guaranteed to meet all specifications listed. Operation under minimum load will not damage the converter. 2. Recommended Dual output models unbalanced load is 5%, if the product operates >5%, it may not be guaranteed to meet all specifications listed. Please contact our technical support for more details. 3. Max. Capacitive Load is tested at input voltage range and full load. 4. All specifications measured at Ta=25C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 5. In this datasheet, all test methods are based on our corporate standards. 6. All characteristics are for listed models, and non-standard models may perform differently. Please contact our technical support for more details. 7. Please contact our technical support for any specific requirement. 8. Specifications of this product are subject to changes without prior notice. MORNSUN Science & Technology Co.,Ltd. Address: No. 5, Kehui St. 1, Kehui development center, Science Ave., Guangzhou Science City, Luogang district, Guangzhou, P.R.China. Tel: 86-20-38601850 Fax: 86-20-38601272 E-mail: info@mornsun.cn Http://www.mornsun-power.com The copyright and authority for the interpretation of the products are reserved by MORNSUN WRE_S-3WR2 & WRF_S-3WR2 2013.07.26-A/3 Page 7 of 7