TC74LCX16374AFT TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74LCX16374AFT Low-Voltage 16-Bit D-Type Flip-Flop with 5-V Tolerant Inputs and Outputs The TC74LCX16374AFT is a high-performance CMOS 16-bit D-type flip-flop. Designed for use in 3.3-V systems, it achieves high-speed operation while maintaining the CMOS low power dissipation. The device is designed for low-voltage (3.3 V) VCC applications, but it could be used to interface to 5-V supply environment for both inputs and outputs. This 16-bit D-type flip-flop is controlled by a clock input (CK) and an output enable input ( OE ) which are common to each byte. It can be used as two 8-bit flip-flops or one 16-bit flip-flop. When the OE input is high, the outputs are in a high-impedance state. All inputs are equipped with protection circuits against static discharge. Weight: 0.25 g (typ.) Features * Low-voltage operation: VCC = 2.0 to 3.6 V * High-speed operation: tpd = 7.0 ns (max) (VCC = 3.0 to 3.6 V) * Ouput current: |IOH|/IOL = 24 mA (min) (VCC = 3.0 V) * Latch-up performance: -500 mA * Package: TSSOP * Power-down protection provided on all inputs and outputs 1 2007-10-19 TC74LCX16374AFT Pin Assignment (top view) 1OE 1 IEC Logic Symbol 48 1OE 1CK 1CK 1Q1 2 47 1D1 1Q2 3 46 1D2 GND 4 45 GND 1Q3 5 44 1D3 1Q4 6 43 1D4 VCC 7 42 VCC 1Q5 8 41 1D5 1Q6 9 40 1D6 GND 10 39 GND 1Q7 11 38 1D7 1Q8 12 37 1D8 2Q1 13 36 2D1 2Q2 14 35 2D2 GND 15 34 GND 2Q3 16 33 2D3 2Q4 17 32 2D4 VCC 18 31 VCC 2Q5 19 30 2D5 2Q6 20 29 2D6 GND 21 28 GND 2Q7 22 27 2D7 2Q8 23 26 2D8 24 25 2CK 2OE 2OE 2CK 1D1 1D2 1D3 1D4 1D5 1D6 1D7 1D8 2D1 2D2 2D3 2D4 2D5 2D6 2D7 2D8 2 1 48 24 25 1EN C1 2EN C2 47 46 44 43 41 40 38 37 36 35 33 32 30 29 27 26 1D 2D 1 2 2 3 5 6 8 9 11 12 13 14 16 17 19 20 22 23 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 1Q8 2Q1 2Q2 2Q3 2Q4 2Q5 2Q6 2Q7 2Q8 2007-10-19 TC74LCX16374AFT Truth Table Inputs Outputs 1OE 1CK 1D1-1D8 1Q1-1Q8 H X X Z X Qn L L L L L H H Inputs Outputs 2OE 2CK 2D1-2D8 2Q1-2Q8 H X X Z L X Qn L L L L H H X: Don't care Z: High impedance Qn: No change System Diagram 1D2 46 1D1 47 1CK 1OE 48 2OE 1D4 43 1D5 41 1D6 40 1D7 38 1D8 37 D D D D D D D D CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q 2 3 5 6 8 9 1Q1 1Q2 1Q3 1Q4 1Q5 1Q6 1Q7 2D2 35 2D3 33 2D4 32 2D5 30 2D6 29 2D7 27 2D8 26 1 2D1 36 2CK 1D3 44 25 11 12 1Q8 D D D D D D D D CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q 24 13 2Q1 14 2Q2 16 17 2Q3 3 2Q4 19 2Q5 20 2Q6 22 2Q7 23 2Q8 2007-10-19 TC74LCX16374AFT Absolute Maximum Ratings (Note 1) Characteristics Symbol Rating Unit Power supply voltage VCC -0.5 to 7.0 V Input voltage VIN -0.5 to 7.0 V -0.5 to 7.0 (Note 2) Output voltage VOUT -0.5 to VCC + 0.5 V (Note 3) Input diode current IIK -50 Output diode current IOK 50 DC output current IOUT 50 mA Power dissipation DC VCC/ground current per supply pin mA (Note 4) mA PD 400 mW ICC/IGND 100 mA Tstg -65 to 150 C Storage temperature Note 1: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 2: Output in OFF state Note 3: High or low state. IOUT absolute maximum rating must be observed. Note 4: VOUT < GND, VOUT > VCC Operating Ranges (Note 1) Characteristics Symbol Power supply voltage VCC Input voltage VIN Output voltage VOUT Output current IOH/IOL Rating Unit 2.0 to 3.6 1.5 to 3.6 (Note 2) 0 to 5.5 V 0 to 5.5 (Note 3) 0 to VCC (Note 4) 24 (Note 5) 12 (Note 6) Operating temperature Topr -40 to 85 Input rise and fall time dt/dv 0 to 10 V V mA C (Note 7) ns/V Note 1: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Note 2: Data retention only Note 3: Output in OFF state Note 4: High or low state Note 5: VCC = 3.0 to 3.6 V Note 6: VCC = 2.7 to 3.0 V Note 7: VIN = 0.8 to 2.0 V, VCC = 3.0 V 4 2007-10-19 TC74LCX16374AFT Electrical Characteristics DC Characteristics (Ta = -40 to 85C) Characteristics Input voltage Symbol Test Condition H-level VIH L-level VIL H-level VOH VIN = VIH or VIL Output voltage VOL VIN = VIH or VIL Input leakage current IIN VIN = 0 to 5.5 V 3-state output OFF state current IOZ Power-off leakage current IOFF Quiescent supply current ICC Increase in Icc per input ICC L-level Min Max 2.7 to 3.6 2.0 2.7 to 3.6 0.8 IOH = -100 A 2.7 to 3.6 VCC - 0.2 IOH = -12 mA 2.7 2.2 IOH = -18 mA 3.0 2.4 IOH = -24 mA 3.0 2.2 IOL = 100 A 2.7 to 3.6 0.2 IOL = 12 mA 2.7 0.4 IOL = 16 mA 3.0 0.4 IOL = 24 mA VCC (V) Unit V V 3.0 0.55 2.7 to 3.6 5.0 A 2.7 to 3.6 5.0 A VIN/VOUT = 5.5 V 0 10.0 A VIN = VCC or GND 2.7 to 3.6 20.0 VIN/VOUT = 3.6 to 5.5 V 2.7 to 3.6 20.0 VIH = VCC - 0.6 V 2.7 to 3.6 500 VIN = VIH or VIL VOUT = 0 to 5.5 V 5 A 2007-10-19 TC74LCX16374AFT AC Characteristics (Ta = -40 to 85C) Characteristics Maximum clock frequency Symbol fmax Propagation delay time tpLH (CK-Q) tpHL 3-state output enable time 3-state output disable time tpZL tpZH tpLZ tpHZ Minimum pulse width tw (H) (CK) tw (L) Test Condition Figure 1, Figure 2 Figure 1, Figure 2 Figure 1, Figure 3 Figure 1, Figure 3 Figure 1, Figure 2 Minimum setup time ts Figure 1, Figure 2 Minimum hold time th Figure 1, Figure 2 Output to output skew Note: tosLH (Note) tosHL Min Max 2.7 3.3 0.3 170 VCC (V) 2.7 8.0 3.3 0.3 1.5 7.0 2.7 8.2 3.3 0.3 1.5 7.2 2.7 8.2 3.3 0.3 1.5 7.2 2.7 4.0 3.3 0.3 3.0 2.7 2.5 3.3 0.3 2.5 2.7 1.5 3.3 0.3 1.5 2.7 3.3 0.3 1.0 Unit MHz ns ns ns ns ns ns ns Parameter guaranteed by design. (tosLH = |tpLHm - tpLHn|, tosHL = |tpHLm - tpHLn|) Dynamic Switching Characteristics (Ta = 25C, input: tr = tf = 2.5 ns, CL = 50 pF, RL = 500 ) Characteristics Symbol Test Condition VCC (V) Typ. Unit Quiet output maximum dynamic VOL VOLP VIH = 3.3 V, VIL = 0 V 3.3 0.8 V Quiet output minimum dynamic VOL |VOLV| VIH = 3.3 V, VIL = 0 V 3.3 0.8 V Typ. Unit Capacitive Characteristics (Ta = 25C) Characteristics Input capacitance Output capacitance Power dissipation capacitance Note: Symbol Test Condition CIN 3.3 7 pF COUT 3.3 8 pF 3.3 25 pF CPD fIN = 10 MHz VCC (V) (Note) CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPDVCCfIN + ICC/16 (per bit) 6 2007-10-19 TC74LCX16374AFT AC Test Circuit Open 6.0 V GND RL Switch Switch tpLH, tpHL Open tpLZ, tpZL 6.0 V tpHZ, tpZH GND tw, ts, th, fmax Open RL Measure CL Output Parameter CL = 50 pF RL = 500 Figure 1 AC Waveform tr 2.5 ns Input (CK) tf 2.5 ns 2.7 V 90% 1.5 V 10% GND tf 2.5 ns tr 2.5 ns Input (D) tw (L) 2.7 V 90% 1.5 V 10% ts (H) Output (Q) tw (H) th (H) ts (L) GND th (L) VOH 1.5 V tpHL VOL tpLH Figure 2 tpLH, tpHL, tw, ts, th tr 2.5 ns tf 2.5 ns 2.7 V 90% 1.5 V Output Enable ( OE ) 10% tpLZ GND tpZL 3.0 V Output (Q) Low to Off to Low 1.5 V tpHZ VOL + 0.3 V VOH - 0.3 V Output (Q) High to Off to High VOL tpZH VOH 1.5 V GND Outputs enabled Outputs disabled Outputs enabled Figure 3 tpLZ, tpHZ, tpZL, tpZH 7 2007-10-19 TC74LCX16374AFT Package Dimensions Weight: 0.25 g (typ.) 8 2007-10-19 TC74LCX16374AFT RESTRICTIONS ON PRODUCT USE * Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 9 2007-10-19