UT54ACTS220 Clock and Wait-State Generation Circuit FEATURES * 1.2 radiation-hardened CMOS - Latchup immune * High speed * Low power consumption * Single 5-volt supply * Available QML Q or V processes * Flexible package - 14-pin DIP - 14-lead flatpack PINOUTS 14-Pin DIP Top View DESCRIPTION The UT54ACTS220 is designed to be a companion chip to UTMC's UT69151 SMMIT family for the purpose of generating clock and wait-state signals. The device contains a divide by two circuit that accepts TTL input levels and drives CMOS output buffers. The chip accepts a 48MHz clock and generates a 24MHz clock. The 48MHz clock can have a duty cycle that varies by 20%. The UT54ACT220 generates a 24MHz clock with a 5% duty cycle variation. The wait-state circuit generates a single wait-state by delaying the falling edge of DTACK into the SMMIT. The clock/timing device generates DTACK from the falling edge of input RCS which is synchronized by the falling edge of 24MHz. The SMMIT drives inputs RCS and DMACK. The devices are characterized over full military temperature range of -55C to +125C. NC 1 14 VDD CLKOUT 2 13 24MHz CLKOUT 3 12 CLKIN 4 11 DTACK TEST NC 5 10 MRST 48MHz VSS 6 9 7 8 RCS DMACK 14-Lead Flatpack Top View NC 1 14 VDD CLKOUT 2 13 24MHz CLKOUT 3 12 CLKIN 4 11 DTACK TEST NC 5 10 MRST 48MHz VSS 6 9 7 8 RCS DMACK LOGIC SYMBOL MRST 48MHz RCS DMACK (10) S (6) (9) (8) CTR1 (13) 1D (12) DTACK S (11) (2) CLKIN 24MHz SRG2 (4) (3) TEST CLKOUT CLKOUT Note: 1. Logic symbol in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 145 RadHard MSI Logic UT54ACTS220 PIN DESCRIPTION Pin Number Pin Name Description 2 CLKOUT Buffered version of CLKIN. 3 CLKOUT Inverted version of CLKIN. 4 CLKIN Clock Input. This signal can be any arbitrary signal that the user wishes to buffer. 6 48MHz 48MHz Clock. The 24MHz clock is created by dividing this signal by two. 8 DMACK 9 RCS 10 MRST Master Reset. This input can be used to preset 24MHz, DTACK and TEST. For normal operation tie MRST to VDD through a resistor. 11 TEST Test output signal. 12 DTACK Data Transfer Acknowledge. This signal can be used to drive the DTACK signal of the SMMIT if the user requires one wait state during the memory transfer. 13 24MHz 24MHz Clock. This output runs at half the frequency of the 48MHz input. The falling edge of 24MHz is the signal that latches the DTACK outputs. 24MHz is forced high whenever MRST is low. Properly loaded, 24MHz will have a 50% duty cycle 5%. DMA Acknowledge. This input is generated by the SMMIT. When high, this signal will cause DTACK output to be forced high. RAM Chip Select. This input is generated by the SMMIT. FUNCTIONAL TIMING: Single SMMIT Wait-State For both read and write memory cycles, DTACK is an input to the SMMIT E and SMMIT LXE/DXE. A non-wait state memory requires two clock cycles, T 1 and T2 of figure 1. For accessing slower memory devices, the UT54ACTS220 holds DTACK to a logical "1". This results in the stretching of memory cycles by one clock to three clock cycles, T W of figure 1. The SMMIT E and SMMIT LXE/DXE samples the DTACK on the rising edge of the 24 MHz clock. If DTACK is not generated before the rising edge of the clock, the SMMIT E and SMMIT LXE/DXE extends the memory cycle. 48MHz 24MHz T1 TW T2 DMACK RCS DTACK Figure 1. Functional Timing RadHard MSI Logic 146 UT54ACTS220 LOGIC DIAGRAM 24MHz D 48MHz MRST RCS Q CK Q RST D DTACK Q CK Q PRE Q D TEST CK Q PRE DMACK CLKIN CLKOUT CLKOUT 147 RadHard MSI Logic UT54ACTS220 RADIATION HARDNESS SPECIFICATIONS PARAMETER LIMIT UNITS Total Dose 1.0E6 rad(Si) SEU Threshold 1 80 MeV-cm2/mg SEL Threshold >120 MeV-cm2/mg Neutron Fluence 2 1.0E14 n/cm2 Notes: 1. Device storage elements are immune to SEU affects. 2. Not tested, inherent of CMOS technology. ABSOLUTE MAXIMUM RATINGS SYMBOL PARAMETER LIMIT UNITS VDD Supply voltage -0.3 to 7.0 V VI/O Voltage any pin -0.3 to V DD +0.3 V TSTG Storage Temperature range -65 to +150 C TJ Maximum junction temperature +175 C TLS Lead temperature (soldering 5 seconds) +300 C JC Thermal resistance junction to case 20 C/W II DC input current 10 mA PD Maximum power dissipation 1 W Note: 1.Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, functional operation of the device at these or any other conditions beyond limits indicated in the operational sections is not recommended. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER LIMIT UNITS VDD Supply voltage 4.5 to 5.5 V VIN Input voltage any pin 0 to VDD V TC Temperature range -55 to + 125 C 48MHz Duty Cycle 50 20% MHz RadHard MSI Logic 148 UT54ACTS220 DC ELECTRICAL CHARACTERISTICS 7 (VDD = 5.0V 10%; V SS = 0V 6, -55C < TC < +125C) SYMBOL PARAMETER CONDITION VIL Low-level input voltage 1 TTL VIH High-level input voltage 1 TTL IIN Input leakage current TTL VDD = 5.5V VIN = VDD or VSS Low-level output voltage 3 Except CLKOUT/CLKOUT IOL = 8mA, VDD = 4.5V IOL = 100A High-level output voltage 3 IOH = -8mA, V DD = 4.5V VOL1 VOH1 MIN MAX UNIT 0.8 V 2.25VDD -1 V 1 A 0.4 0.25 V 3.15VDD V Except CLKOUT/CLKOUT VOL2 CLKOUT/CLKOUT Low-level output voltage 3 IOL = 100A VOH2 CLKOUT/CLKOUT High-level output voltage 3 IOH = -100A Short-circuit output current 2 ,4 VO = V DD and VSS IOS 0.25 V VDD4.25 V +300 mA VDD = 5.5V IOL1 IOH1 IOL2 IOH2 IIH Output current 10 VIN = VDD or VSS (Sink), Except CLKOUT/CLKOUT VOL = 0.4V Output current 10 VIN = VDD or VSS (Source), Except CLKOUT/CLKOUT VOH = V DD - 0.4V CLKOUT/CLKOUT output current10 VIN = VDD or VSS (Sink) VOL = 0.4V CLKOUT/CLKOUT output current10 VIN = VDD or VSS (Source) VOH = V DD - 0.4V Input current high VIN = VDD or VSS 8 mA -8 mA 12 mA -12 mA +1.0 A -1.0 A VIN = 5.5V IIL Input current low VIN = VDD or VSS VIN = V SS Ptotal Power dissipation 2, 8, 9 CL = 50pF 1.0 mW/ MHz IDDQ Quiescent Supply Current VDD = 5.5V 10 A VIN = VDD or V SS 149 RadHard MSI Logic UT54ACTS220 IDDQ Quiescent Supply Current Delta For input under test 1.6 mA VIN = VDD - 2.1V For all other inputs VIN = VDD or VSS VDD = 5.5V CIN COUT Input capacitance 5 = 1MHz @ 0V 15 pF Output capacitance 5 = 1MHz @ 0V 15 pF Notes: 1. Functional tests are conducted in accordance with MIL-STD-883 with the following input test conditions: V IH = VIH(min) + 20%, - 0%; V IL = VIL(max) + 0%, - 50%, as specified herein, for TTL, CMOS, or Schmitt compatible inputs. Devices may be tested using any input voltage within the above specified range, but are guaranteed to VIH (min) and V IL (max). 2. Supplied as a design limit but not guaranteed or tested. 3. Per MIL-PRF-38535, for current density 5.0E5 amps/cm 2, the maximum product of load capacitance (per output buffer) times frequency should not exceed 3,765 pF/MHz. 4. Not more than one output may be shorted at a time for maximum duration of one second. 5. Capacitance measured for initial qualification and when design changes may affect the value. Capacitance is measured between the designated terminal and VSS at frequency of 1MHz and a signal amplitude of 50mV rms maximum. 6. Maximum allowable relative shift equals 50mV. 7. All specifications valid for radiation dose 1E6 rads(Si). 8. Power does not include power contribution of any TTL output sink current. 9. Power dissipation specified per switching output. 10. This value is guaranteed based on characterization data, but not tested. RadHard MSI Logic 150 UT54ACTS220 AC ELECTRICAL DIAGRAM 48MHz 24MHz RCS T1 TW TW T2 tSUR DTACK tSU tH CLKIN CLKOUT or CLKOUT 151 tPHL or tPLH RadHard MSI Logic UT54ACTS220 AC ELECTRICAL CHARACTERISTICS 2 (VDD = 5.0V 10%; V SS = 0V1, -55C < TC < +125C) SYMBOL PARAMETER MINIMUM MAXIMUM UNIT tPHL1 48MHz to 24MHz 0 15 ns tPLH1 48MHz to 24MHz 0 15 ns tPHL2 24MHz to DTACK 0 7 ns tPLH2 24MHz to DTACK 0 6 ns tPLH3 DMACK to DTACK 3 16 ns tPLH4 MRST to 24MHz , DTACK 3 16 ns tPHL5 CLKIN to CLKOUT 0 11 ns tPLH5 CLKIN to CLKOUT 0 11 ns tPHL6 CLKIN to CLKOUT 0 11 ns tPLH6 CLKIN to CLKOUT 0 11 ns tSU 3 DTACK to 24MHz , setup time 12 ns tH3 24MHz to DTACK , hold time 20 ns tSUR Setup time from RCS to 24MHz 7 ns tWM MRST pulse width low 5 ns tWC CLKIN pulse width 12 ns fMAX Maximum CLKIN frequency 40 MHz Notes: 1. Maximum allowable relative shift equals 50mV. 2. All specifications valid for radiation dose 1E6 rads(Si). 3. Guaranteed by design but not tested. RadHard MSI Logic 152