XLG-75 75W Constant Power Mode LED Driver series IS 15885(Part 2/Sec13) THOMAS SAMUEL THOMAS SAMUEL Note.15 R-41027766 (for XLG-75I type only ) (Except for Blank type) Note.12 : File Name:XLG-75-SPEC 2020-12-03 75W Constant Voltage + Constant Current LED Driver XLG-75 series SPECIFICATION XLG-75 MODEL DC VOLTAGE OUTPUT 16.8~ 24V 3.1A 74.4W 240mVp-p 1.55A~3.1A 2.0% LINE REGULATION 0.5% 0.5% LOAD REGULATION SETUP, RISE TIME Note.6 2% 1% 500ms, 100ms/230VAC, 1200ms, 100ms/115VAC HOLD UP TIME (Typ.) 10ms/ 230VAC 10ms/ 115VAC Note.5 FREQUENCY RANGE POWER FACTOR TOTAL HARMONIC DISTORTION EFFICIENCY (Typ.) AC CURRENT INRUSH CURRENT(Typ.) -24- 100 ~ 305VAC 142 ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" section) 47 ~ 63Hz PF0.97/115VAC, PF0.95/230VAC, PF0.92/277VAC@full load THD< 10%(@load50%/115VC,230VAC; @load75%/277VAC) 90% 89% 1.0A / 115VAC 0.45A / 230VAC 0.38A/277VAC COLD START 50A(twidth=300s measured at 50% Ipeak) at 230VAC; Per NEMA 410 MAX. No. of PSUs on 16A CIRCUIT BREAKER 9 units (circuit breaker of type B) / 14 units (circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC NO LOAD POWER CONSUMPTION No load power consumption <0.5W(for standard version) OVER CURRENT SHORT CIRCUIT PROTECTION XLG-75 24V CONSTANT CURRENT REGION Note.2 8.4~ 12V RATED CURRENT 5A 60W RATED POWER RIPPLE & NOISE (max.) Note.3 150mVp-p 2.5A~5A CURRENT ADJ RANGE VOLTAGE TOLERANCE Note.4 3.0% VOLTAGE RANGE INPUT -12- 12V OVER VOLTAGE INPUT OVER VOLTAGE Note.7 OVER TEMPERATURE WORKING TEMP. MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT 95 ~ 108% Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed 13 ~ 19V 26 ~ 36V Shut down output voltage, re-power on to recover 320 ~ 370VAC (Shut down output voltage when the input voltage exceeds protection voltage, recovers automatically after fault condition is removed) Can survive input voltage stress of 440Vac for 48 hours @ tc 75 max Shut down output voltage, re-power on to recover Tcase=-40 ~ +90 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section) Tcase=+90 20 ~ 95% RH non-condensing -40 ~ +90, 10 ~ 95% RH 0.03%/ (0 ~ 60) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.7 UL8750(type"HL"), UL879, CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13 independent, EN62384;GB19510.1,GB19510.14; EAC TP TC 004;J61347-1(H29), J61347-2-13(H29),KC61347-1,KC61347-2-13,IS15885(Part2/Sec13)(for XLG-75I type only); NOM-058-SCFI-2017(except for Blank type);IP67 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH I/P-FG:2KVAC Parameter EMC EMISSION EMC SAFETY & O/P-FG:1.5KVAC Standard EN55015(CISPR15) ,GB/T17743 Test Level/Note Conducted Radiated EN55015(CISPR15) ,GB/T17743 ----- Harmonic Current EN61000-3-2 ,GB/T17625.1 Class C @load50% Voltage Flicker EN61000-3-3 ----- Parameter Standard Test Level/Note ESD EN61000-4-2 Level 3, 8KV air ; Level 2, 4KV contact Radiated EN61000-4-3 Level 3 EFT/Burst EN61000-4-4 Level 3 Surge EN61000-4-5 4KV/Line-Line 6KV/Line-Earth Conducted EN61000-4-6 Level 3 Magnetic Field EN61000-4-8 Level 4 Voltage Dips and Interruptions EN61000-4-11 >95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods ----- EN61547 EMC IMMUNITY MTBF 1232.28K hrs min. Telcordia SR-332 (Bellcore) ; 140*63*32mm (L*W*H) 0.58Kg;24pcs /15Kg /0.85CUFT 376.3Khrs min. MIL-HDBK-217F (25) OTHERS DIMENSION PACKING NOTE File Name:XLG-75-SPEC 2020-12-03 , https://www.meanwell.com/serviceDisclaimer.aspx XLG-75 75W Constant Power Mode LED Driver series SPECIFICATION MODEL OUTPUT XLG-75 RATED POWER CONSTANT CURRENT REGION 74.9W 53 ~ 107V 75.6W 27 ~ 56V FULL POWER CURRENT RANGE 700~1050mA 1300~2100mA OPEN CIRCUIT VOLTAGE (max.) 115V 60V CURRENT ADJ. RANGE 350~1050mA 650~2100mA CURRENT RIPPLE CURRENT TOLERANCE 3.0%(@rated current) 5% SET UP TIME 500ms/230VAC, 1200ms/115VAC Note.5 100 ~ 305VAC 142VDC ~ 431VDC (Please refer to "STATIC CHARACTERISTIC" ang " DRIVING METHODS OF LED MODULE"section) FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF0.97 / 115VAC, PF0.95 / 230VAC, PF0.92 / 277VAC at full load (Please refer to "Power Factor Characteristic" section) TOTAL HARMONIC DISTORTION THD< 10% (@ load50% at 115VAC/230VAC ,@load75% at 277VAC) Please refer to "TOTAL HARMONIC DISTORTION (THD)" section EFFICIENCY (Typ.) 91% AC CURRENT (Typ.) INRUSH CURRENT(Typ.) 1A / 115VAC 0.45A / 230VAC 0.38A / 277VAC COLD START 50A(twidth=300s measured at 50% Ipeak) at 230VAC; Per NEMA 410 MAX. NO. of PSUs on 16A CIRCUIT BREAKER 9 unit(circuit breaker of type B) / 14 units(circuit breaker of type C) at 230VAC LEAKAGE CURRENT <0.75mA / 277VAC STANDBY POWER CONSUMPTION Standby power consumption <0.5W for AB-Type(Dimming OFF)(for standard version) PROTECTION SHORT CIRCUIT INPUT OVER VOLTAGE Note.7 90% 110 ~ 150% Hiccup mode, recovers automatically after fault condition is removed Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed 320 ~ 370VAC (Shut down output voltage when the input voltage exceeds protection voltage, recovers automatically after fault condition is removed) OVER TEMPERATURE Can survive input voltage stress of 440Vac for 48 hours @ tc 75 max Shut down output voltage, re-power on to recovery WORKING TEMP. Tcase=-40 ~ +90(Please refer to "OUTPUT LOAD vs TEMPERATURE" section) MAX. CASE TEMP. Tcase=+90 20 ~ 95% RH non-condensing WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY EMC -H- 1400mA OVER POWER SAFETY & XLG-75 700mA VOLTAGE RANGE INPUT -L- RATED CURRENT -40 ~ +80, 10 ~ 95% RH non-condensing TEMP. COEFFICIENT 0.03%/ (0 ~ 60) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS Note.7 UL8750(type"HL"), CSA C22.2 No. 250.13-12; ENEC EN61347-1, EN61347-2-13 independent, EN62384; GB19510.1,GB19510.14; EAC TP TC 004;J61347-1(H29), J61347-2-13(H29),KC61347-1,KC61347-2-13,IS15885(Part2/Sec13)(for XLG-75I type only); NOM-058-SCFI-2017(except for Blank type);IP67 approved WITHSTAND VOLTAGE I/P-O/P:3.75KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25/ 70% RH I/P-FG:2KVAC Parameter EMC EMISSION O/P-FG:1.5KVAC Standard EN55015(CISPR15) ,GB/T17743 Test Level/Note Conducted Radiated EN55015(CISPR15) ,GB/T17743 ----- Harmonic Current EN61000-3-2 ,GB/T17625.1 Class C @load50% Voltage Flicker EN61000-3-3 ----- Parameter Standard Test Level/Note ESD EN61000-4-2 Level 3, 8KV air ; Level 2, 4KV contact Radiated EN61000-4-3 Level 3 EFT/Burst EN61000-4-4 Level 3 Surge EN61000-4-5 4KV/Line-Line 6KV/Line-Earth Conducted EN61000-4-6 Level 3 Magnetic Field EN61000-4-8 Level 4 Voltage Dips and Interruptions EN61000-4-11 >95% dip 0.5 periods, 30% dip 25 periods, >95% interruptions 250 periods ----- EN61547 EMC IMMUNITY MTBF 1232.28K hrs min. OTHERS DIMENSION 140*63*32mm (L*W*H) 0.58Kg;24pcs /15Kg /0.85CUFT NOTE , https://www.meanwell.com/serviceDisclaimer.aspx File Name:XLG-75-SPEC 2020-12-03 PACKING Telcordia SR-332 (Bellcore) ; 376.3Khrs min. MIL-HDBK-217F (25) XLG-75 75W Constant Power Mode LED Driver series BLOCK DIAGRAM PFC fosc : 50~120KHz PWM fosc : 65KHz EMI FILTER & RECTIFIERS I/P RECTIFIERS & FILTER POWER SWITCHING PFC CIRCUIT +V -V DIM+ DIM- O.C.P. (AB Type) FG O.L.P. DETECTION CIRCUIT PWM CONTROL PFC CONTROL O.T.P. O.V.P. (12/24V) DRIVING METHODS OF LED MODULE I-V Operating Area 60V 650mA, 56V 115V 105V 50V 95V 45V 85V 40V 2100mA, 36V 1050mA, 71V 75V 35V 65V 30V 55V 25V 700mA, 53V 45V 0mA 1300mA, 56V 55V 700mA, 107V 350mA, 107V 200mA 400mA 600mA 800mA 1050mA, 53V 1000mA 1200mA Recommend Performance Region 1300mA, 27V 2100mA, 27V 20V 0mA 350mA 700mA 1050mA 1400mA 1750mA 2100mA Recommend Performance Region This series is able to work in either Constant Current mode (a direct drive way) or Constant Voltage mode (usually through additional DC/DC driver) to drive the LEDs. Vo(%) 100 (B) Constant Current area (A) Constant Voltage area 60 (min.) (C) Hiccup Protection 50 100 In the constant current region, the highest voltage at the output of the driver depends on the configuration of the end systems. Should there be any compatibility issues, please please contact MEAN WELL. Io(%) Typical output current normalized by rated current (%) File Name:XLG-75-SPEC 2020-12-03 XLG-75 75W Constant Power Mode LED Driver series DIMMING OPERATION AC/N(Blue) AC/L(Brown) FG(Green/Yellow) V-(Black) V+(Red) XLG-75 DIM+( Blue ) DIM-(White) 3 in 1 dimming function (for AB-Type) Output constant current level can be adjusted by applying one of the three methodologies between DIM+ and DIM-: 0 ~ 10VDC, or 10V PWM signal or resistance. Direct connecting to LEDs is suggested. It is not suitable to be used with additional drivers. Dimming source current from power supply: 100A (typ.) 100% 90% Vo- + + - - DIM+ + Output current (%) 80% Vo+ 70% 60% 50% 40% 30% Additive Voltage - 20% DIM- 10% 0% "DO NOT connect "DIM- to Vo-" 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V Dimming input: Additive voltage 100% 90% Vo- + + - - DIM+ Output current (%) 80% Vo+ 70% 60% 50% 40% 30% Additive PWM signal 20% DIM- 10% 0% "DO NOT connect "DIM- to Vo-" 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Duty cycle of additive 10V PWM signal dimming input 100% 90% Vo- + 80% + - - DIM+ Additive Resistance Output current (%) Vo+ 70% 60% 50% 40% 30% DIM"DO NOT connect "DIM- to Vo-" 20% 10% 0% Short 10K/N 20K/N 30K/N 40K/N 50K/N 60K/N 70K/N 80K/N 90K/N 100K/N (N=driver quantity for synchronized dimming operation) Dimming input: Additive resistance Note : 1. Min. dimming level is about 8% and the output current is not defined when 0%< Iout<8%. 2. The output current could drop down to 0% when dimming input is about 0 or 0Vdc, or 10V PWM signal with 0% duty cycle. File Name:XLG-75-SPEC 2020-12-03 XLG-75 75W C onstant Power Mode LED Driver series OUTPUT LOAD vs TEMPERATURE 230VAC 100 100 80 80 230VAC Input only 100VAC 60 LOAD (%) LOAD (%) 60 40 20 -40 230VAC Input only -30 -10 0 15 30 50 60 40 20 -40 70 (HORIZONTAL) -30 0 10 30 50 70 90 (HORIZONTAL) If XLG-75 operates in Constant Current mode with the rated current the maximum workable Ta is 60 (Typ. 230VAC) or 50 (Typ.100VAC) Below 110VAC@ -30 may retry to 2nd setup STATIC CHARACTERISTIC POWER FACTOR (PF) CHARACTERISTIC Tcase at 75 Constant Current Mode 100 1 90 0.95 PF 80 LOAD (%) 70 0.9 277V 60 230V 0.85 115V 50 0.8 40 0.75 100 110 140 160 180 200 220 240 260 280 305 (300W) 50% 60% 70% INPUT VOLTAGE (V) 60Hz 90% 100% LOAD TOTAL HARMONIC DISTORTION (THD) EFFICIENCY vs LOAD XLG-75 series possess superior working efficiency that up to 92% can be reached in field applications. XLG-75-L Model, Tcase at 75 XLG-75-L Model, Tcase at 75 96 10% 92 8% 88 6% 277V 5% 230V 4% 115V 3% 2% EFFICIENCY(%) 9% 7% THD 80% 84 277V 80 230V 76 115V 72 68 64 1% 60 0% 50% 60% 70% 80% 90% 100% 50% 60% 70% 80% 90% LOAD LOAD File Name:XLG-75-SPEC 2020-12-03 XLG-75 75W Constant Power Mode LED Driver series LIFETIME 120 100 LIFETIME(Kh) 80 60 40 20 0 25 30 35 40 45 50 55 60 65 70 75 80 85 90 Tcase ( ) File Name:XLG-75-SPEC 2020-12-03 XLG-75 75W Constant Power Mode LED Driver MECHANICAL SPECIFICATION Case No.: 275A series Unit:mm Blank-Type 140 134 125 30020 40 SJOW 17AWGx3C &H05RN-F 3x1.0mm 2 tc V-(Black) V+(Red) 57 SJOW 17AWGx2C &05RN-F 2x1.0mm 2 24 AC/N(Blue) AC/L(Brown) FG(Green/Yellow) 63 30020 4-4.5 32 tc A-Type 140 134 125 30020 40 SJOW 17AWGx3C &H05RN-F 3x1.0mm 2 tc V-(Black) V+(Red) 57 SJOW 17AWGx2C &05RN-F 2x1.0mm 2 24 4-4.5 32 tc 39.7 12.7 AC/N(Blue) AC/L(Brown) FG(Green/Yellow) 63 30020 File Name:XLG-75-SPEC 2020-12-03 XLG-75 75W Constant Power Mode LED Driver MECHANICAL SPECIFICATION Case No.: 275A series Unit:mm AB-Type 140 134 125 30020 30020 40 V-(Black) V+(Red) SJOW 17AWGx3C &H05RN-F 3x1.0mm 2 tc DIM+( Blue ) DIM-(White) 57 UL2517 20AWGx2C 24 AC/N(Blue) AC/L(Brown) FG(Green/Yellow) 63 SJOW 17AWGx2C 2 &05RN-F 2x1.0mm 35020 4-4.5 32 tc 12.7 39.7 INSTALLATION MANUAL File Name:XLG-75-SPEC 2020-12-03