20 Micro-D Metal Shell .050 Center Spacing MDM connectors are used in applications requiring highly reliable, extremely small, lightweight connec- tors with higher density contact configurations than available in traditional rectangular connectors. They are available in 8 shell sizes accommodating from 9 ta 100 contacts, and special arrangements of power and coaxial contacts. These connectors are designed to meet the rapidly increasing demands for an environmental, high per- formance, rugged, moisture-sealed microminiature connector. This connector employs size 24 MICRO- MDM PIN/MICROSOCKET contacts on .050(1.27) centers in a contact density identical to the stan- dard MICRO-D connector series, but with these additional features: Aluminum shells to provide greater strength, prevent chipping, cracking or breaking, offer electromagnetic (EMI) and RFI shielding. Silicone elastomer compression interfacial seal to provide a moisture and humidity seal between each contact and between contacts and shell. How to Order SERIES MDM: Diallyl Phthalate Insulator Material MDMV: Polyester Insulator Material CONTACT ARRANGEMENTS 9-15-21-25-31-37-51-100 (standard) 702, 24C4, (coaxial) ? or combination of 7P2, 24P4 (power) coax and power CONTACT TYPE P Pin S Socket TERMINATION TYPE H Harness-insulated wire. L - Solid-uninsulated wire. S Solder pot to accept #26 AWG MAX. harness wire. (Not available with power contact arrangements.) SERIES CONTACT ARRANGEMENTS _ | 51 P H 001 P - XXX CONTACT TYPE TERMINATION TYPE TERMINATION CODE HARDWARE SHELL FINISH MOD CODES TERMINATION CODE* F Float mount (H) 001 - 18, 7/34 strand, #26 AWG, B No hardware standard MIL-W-16878/4, Type E Teflon, .091 (2.31) dia. hole for sizes 9-51; yellow. .120 (3.05) dia. hole for size 100. (H) 003 18, 7/34 strand, #26 AWG, A .125 (3.18) dia. mounting holes for MIL-W-16878/4, Type E Teflon, sizes 9-51; color coded to MIL-STD-681 .166 (4.22) dia. hole for size 100. System I. Bi .1475 (3.75) dia. hole for size 100 {L) 1 1/2 uninsulated solid #25 (Per MIL-C-83513) AWG gold plated copper. SHELL FINISH MOD CODES** (L) 2 1 uninsulated solid #25 AWG No gold plated copper. Number - Standard Cadmium/yellow chromate HARDWARE A174 Electroless nickel M - Military specification hardware, see A172. Gold over nickel page 25. A141 _Irridite/alodine Jackpost A30) = :_ Black anodize P K Jackscrewstandard L Jackscrewlow profile *See Termination Codes page 21 for additional length Modification Codes. **For other modifications not listed, consult the factory. Standard Data STANDARD MATERIALS AND FINISHES MECHANICAL FEATURES Shell Aluminum alloy per 00-A-200/8 (6061-16), yellow chromate / cadmium per 00-P-416, Type Il, class 3. Insulator Glass-filled dially! phthalate per MIL-M-14, Type SDGF, or polyester per MIL-M-24519, Type GPT-30F Contacts Copper alloy, gold plate Mounting Hardware 300 Senes stainless steel, passivate Kit, Jackpost (3) Items 300 Senes stainless steel, passivate Coupling Friction/jackscrews Polarization Keystone-shaped shells Contact Spacing - .050 (1.27) Centers Shell Styles Plug and receptacle ELECTRICAL DATA No. of Contacts - 9 thru 100 standard; 5 signal/2 coaxial; Washer 400 Series stainless steel, passivate 5 signal/2 power; Standard Epoxy Hysol 4198 with HD3561 hardener a Sr coal color green or EE4215 with HO3561, Signal power color black Coaxial Cable - RG-178/U Wire Size #24 thru #32 AWG Contact Termination Multiple indent crimp ITT Cannon Dimensions are shown tn inches (millimeters) Dimensions subject to change. Microminiature Products 666 Dyer Rd. PO Box 929, Santa Ana, CA 92702-0929 (714) 557-4700 FAX (714) 754-2142 M 9005424 0000546 195Micro-D Metal Shell - .050 Center Spacing MDM Standard Wire Termination Codes Cannon Modification Code (Not MS) The following termination cades are listed for your information. For lengths not shown, consult factory for proper modification code. All wire lengths are minimum. Harness Type (H) Solid Uninsulated Type (L) #26 AWG per MIL-W-16878/4, 7/34 strand, type E Teflon, stranded. #25 AWG gold plated copper. Length All Yellow Color Coded* Termination Code Length 3 (76.2) H020 H027 L61 125 (3 18) 6 (152.4) HO19 HOtG 156 150 (3.81) 8 (203.2) H026 H034 57 .190 (4.83) 10 (254.0) H029 H025 139 .250 (6.35) 12 (304.8) H028 HO02 L58 .375 (9.52) 18 (457.2) HO01 HO03 ll 500 (12.70) 20 (508 0} H038 H023 L14 .750 (19.05) 24 (609.6) HO09 HO04 L2 1.000 (25.40) _ 30 (762.0) HO10 HO05 U7 1.500 (38.10) 36 (914.4) H011 HO06 L6 2.000 (50.80) ~ 48 (1219.2) HO13 HO48 Li6 2.500 (63.50) 72 (1828.8) HO17 HO46 L10 3.000 (76.20) 120 (3048.0) H042 H041 Millmeters are in parentheses. *Cavity #1 black Contact Arrangements (Face View of Pin Insert - Use Reverse Order for Socket Side) Standard os 12 FOY abe Tee 09) _ $2 3a4a5 12348 6 74 3234 56 Ya Bilov ayes @ IG bt 121N ta tS 5 Contacts 15 Contacts 23 44 6 7 @ 9 sO tag a @ 7 BF IDI ED TRIAS % Ltr itty : eevee aee se > Cc speecees oe Voeeseeeees iT ey Ce ee sere eeesevesron TEES TTTT TTT. oN t Prt tt i ES 16 17 1G $9 20 21 22 2994 28 7 18 19 202) RR FIRS ZEA 2B ASSO 9 20 2122232425 26 27 28 2930 31329343085 3897 25 Contacts 31 Contacts 37 Contacts t 2g 4 8 3 WO tr 5F 04 15 1B TP WB 1G 28 at 22 29 2 25 2B & 486 7 8 F 10 11123 IB ITE 12a la ek salsdaalas! by classe setae f pane lowe waleieele ae leialeleieie Stee oetevoeveeeaeoen * * GGp 62 }Ga 69 7D] 7172; THE Te t 185/64 165 [66 87 ; 36373929 40.4) 42 49444526467484956 81 6 20 O86 OF 60 B) 82 83 4 BS 86 BT BB B49 St G2 83 9a G8 Gh AT oy BR IO 51 Contacts 100 Contacts Contact tdentificatian numbers are for reference only and do not appear on insulator or connector body. Coaxial 320 pe 98 (18.18) my {8.13} [em a60 (rsa) C of @ 2 299,58 ee 067 Size 25 Shell Size 5 Shell iat 5 Micro Contact 20 Micro Contacts 2 Coax or 2 Power 4 Coax or 4 Powar {Not MS} [TTT Cann n Dimensions are shown in tiches (millimeters) 0 Dimensions subject to change = Micromimature Products 666 E Oyer Rd, PO Box 929, Santa Ana, CA 92702-0929 (714) 557-4700 FAX (714) 754-2142 me 9005424 0000587 02S22 Micro-D Metal Shell - .050 Center Spacing MDM Shell Dimensions (Conforms to MIL-C-83513) ms 186 (4,729 088 TwoMTe. Hoes mea an 8 uae | 238) _ jag a = ait sa i =f B I rere 410 (157 : & a i ' | Cd & : nn a Solder Pot Receptacle Receptacle (MDM-100 only) SME song.) (mee Heats an sina | | | wax. Pp 93 238) ~ i IUFit Gell ee; 4. Pigtail Termination ie : Bet F _ Part Number A B C D E +.005 G Average Weights** By Shell Size Max. Max. Max. Max. Max. (0.13) Max. oz. (gm.) 25% MDM-9P* 785 (19.94) 334 (8.48) 400 (10.16) .270 {6.86} 308 (7.82) 565 (14.35) 185 (4.70) .063 {1.79} ~ MDM-9S* .785 (19.94) 402 (10.21) 400 (10.16) .270 (6.86} 308 (7,82) 565 (14.35) .253 (6.43) 063 (1.79) MDM-15P* 935 (23,75) 484 (12.29) 550 (13.9.7) .270 (6.86) 308 (7.82) 715 (18.16) .185 (4.70) 084 (2.39) MOM-15S* 935 (23.75) 552 (13.97) 550 (14.02) .270 (6.86) 308 (7.82) 715 (18.16) .253 (6.43) 083 (2.37) MOM-21P* 1.085 (27.56) 634 (16.10) 700 (17.78) 270 (6.86) 308 (7.82) 865 (21.97) .185 (4.70) 105 (2.99} MOM-21S* 1.085 (27.56) 702 (17.83) 700 (17.78) 270 {6.86} 308 (7 82) 865 (21.97) .253 (6.43) 104 (2.97) MDM-25P* 1.185 (30.10) 734 (18.64) 800 (20 32) 270 (6.86) 308 (7,82) 965 (24.51) .185 (4.70) 119 (3.39) MDM-25S* 1.185 (30.10) 802 {20 37} 800 (20.32) .270 (6.86) 308 (7,82) 965 (24.51) .253 (6.43) 118 (3.36) MDM-31P* 1.335 (33.91) 884 (22.45) 950 (24.13) 270 (6.86) 308 (7.83} 1.115 (28.32) 185 (4.70) 140 (3.99) MDM-31S* 1.335 (33.91) 952 (24.18) 950 (24.13) 270 (6.86) 308 (7.83} 1.115 (28.32) .253 (6,43) 139 (3.96) _ MDM-37P* 1.485 (37.72) 1.034 (26.26) 1.100 (27.94) 270 (6.86) 308 (7.82) 1 265 (32.13) 185 (4.70) .161 (4.59) MDM-37S* 1.485 (37.72) 1.102 (27.99) 1.100 (27.94) 270 (6.86} 308 (7.82) 1 265 (32.13) .253 (6.43} 160 (4.56) ~~ MDM-51P* 1.435 {36.45} 984 (24.99) 1.050 (26.67) 310 (7.87) 351 (8.92) 1.215 (30.86) 228 {5.79} 193 (5.50) MDM-51S* 1.435 (36.45) 1.052 (26.72) 1.050 (26.67) 310 (7.87) 351 (8.92) 1.215 (30.86) 296 (7.52) .188 (5.35) MDM-100P* 2.170 (55.12) 1.384 (35.15) 1.442 (36.63) 360 (9.14) 394 (10.01) 1.800 (45.72) 271 (6,88) 500 {14.3} MDM-100S* 2.170 (55.12) 1.508 (38.10) 1,442 (36.63) 360 (9.14) .394 (10.01) 1.800 (45.72) 394 (10.01) 1.040 (29.5) *Add lead type and length; see How To Order. **Weight given is 1/2, uninsulated, solid, #25 AWG gold plated copper pigtails. Panel Mounting Dimensions (Sizes 9 100) hoe : ont ine? : ony oy Plug and Receptacle Plug front Mounted _ Rear Mounted Receptacle Rear Mounted ITT Cannon Dimensions are shown in inches (millimeters). Dimensions subject to change Microminiature Products 666 E Dyer Rd, PO Box 929, Santa Ana, CA 92702-0929 (714) 557-4700 FAX (714) 754-2142 MP 9005424 9000585 Th) aMicro-D Metal Shell - .050 Center Spacing MDM Panel Cutouts NOTE: See page 24 for rear pane! mounting configuration Shell Sizes 9 thru 51 450 202 rin Cy (1943:20.08) D (254) 9) 4 030 (0.76) TYP TYP prerrrrmnnne C __| ne Jae A enti L aTee j b { { t se 3 4 , 8 pb yr? Te ara tr OO >f FULLR A 015 10.38} 8 FOUL EYP) rye j MAX, (TYP) 26/27 TYP FBLL Re TYP } PANEL REF Figure 1 Figure 2 Figare 3 Front Mounting Rear Mounting Edgeboard Mounting Shell Size 100 450 & 002 je 1 805 2.5 a ia =0esi] i078) THe (45 85 28) 718 a8 VIB 28S few 1-805 138 298 805 1.84 > . (300 43 (3.00 #14) 45.85 ea) (3.00 ia . 885338) |} r i t_ ad C @it Me +e LL 401 23 uy Co TE Ry poet (70 18 288 oo see 33) "| K~ asst ea ! 4 O45 (0,38) . 125 4% . , : R MAX (TYP) FAL RCV) (8.18 438) FULLR (TYP ) PULL R. (FYP.) PANEL REF. Figure 1 we 2 Figue 3 Front Mounting Rear Mounting Edyeboard Mounting For 9-51 Shell Sizes . A B C 0 NOTES: Shell Cutout +004 (0.10) +004 (0.10) + 005 (0.13) + 005 (0.13) 1. Front mounting {figure 1) and rear mounting (figure 2) Size Figure ,000 (0.00) ,000 (0.00) 000 (0.00) ,000 (0.00) accommodates #2-56 screws. - - - - - - - - 2. Front mounting is preferred. However, when rear mounting Is 1 408 (10.36) 271 (6.88) 570 (14.48) 089 (2.26) necessary, use figure 2 dimensions when jackscrews are 9 2 A01 (10 19) 252 (6.40) 570 (14.48) 089 (2.26) used. See detail on page 24 when jackposts are used. 3 Edgeboard mounting bracket (figure 3) uses #2-56 screws. 3 570 (14.48) 089 (2.26) Dimension .450 + .002 (11.43 + 0 05) locates the MDM 1 558 (14.17) 271 (6.88) 720 (18.29) 089 (2.26) receptacle flush with the end of the board. 15 2 551 (14.00) 252 (6.40) 670 (18.29) 089 (2 26) . 3 - - 720 (18.29) 089 (2.26) For 100 Shell Size 1 708 (17.98) 271 (6.88) 870 (22.10) 089 (2 26) 1. Front mounting (figure 1) and rear mounting (figure 2) 21 2 701 (47.81) 252 (6 40) 870 (22.10) 089 (2 26) accommodates #4-40 screws 3 - - 870 (22.10) 089 (2.26) 2. Edgeboard mounting bracket (figure 3) uses #4-40 screws. Dimension 450 + .002 (11.43 - 0 05) locates the MOM 1 808 (20.52) 271 (6.88) 970 (24.64) 089 (2.26) receptacle flush with the end of the board 25 2 804 (20.34) 252 (6.40) 970 (24.64) 089 (2.26) 3 Front mounting ts preferred. However, when rear mounting Is 3 _ _ 970 (24.64) 089 (2.26) necessary, use figure 2 dimensions - - - - ] 958 (24 33) .27) (6.88) 1.120 (28 45) 089 (2.26) ct | 2 951 (24.16) .252 (6.40) 1.120 (28.45) 089 (2.26) 3 - - 1.120 (28 45) 089 (2.26) 1 1 108 (28.14) 274 (6.88) 1.270 (32.26) 089 (2.26) 37 2 1101 (27.97) .252 (6.40) 1.270 (32.26) 089 (2.26) 3 - - 1.270 (32.26) 089 (2.26) 1 1.058 (26.87) 315 (8.00) 1.220 (30.99) 089 (2 26) 51 2 1.051 (26.70) 295 (7.49) 1 220 (30 99) 089 (2.26) 3 - - 1.220 (30.99) 089 (2.26) D sions are shown in inches (millimeters). TTT Cannon seasons a Dimensions subject to change 23 Microminature Products 666 E Dyer Rd, PO Box 929, Santa Ana CA 92702-0929 (714) 557-4700 FAX (714) 754 2142 Mm 9005424 9000589 5TS omThe Micro Line - The Cannon MICRO Series established the stan- dards for performance and reliability in micraminia- ture interconnects. Exceptionally versatile, MICRO connectors are available in rectangular, circular, and strip configurations, with 3 amp MICROPIN/ MICROSOCKET contacts on .050(1.27) centers, or with special arrangements of power and coaxial contacts. The heart of the Cannon MICROPIN / MICROSOCK- ET contact system is a multi-element Twist Pin Contact recessed within an insulating housing. The rugged, cylindrical sockets are mounted in the exposed half of the connector. When connector halves are mated, the chamfered sockets are first aligned by the connector body, then guide the spiral MICROPIN contacts into proper and positive align- ment, even under worst-case tolerance conditions. This is Cannon's POS-A-LINE connector design. The multiple spring elements of the MICROPIN, then under compression, form a multi-point contact system of high mechanical and electrical integrity. Contacts will provide a high degree of reliability over hundreds of mating and unmating cycles, and have proven themselves in applications that range from commercial products to equipment that has been landed on the moon. Contact rating - 3 amps max. Contact centers .050(1.27). Wire sizes #24 thru #32 AWG, stranded or solid. Contact terminationmultiple indent crimp. Contact retention fixed via epoxy. Contact materials and finish Copper alloy, gold-plated per MIL-G-45204, Type Il, Grade C, Class 1 over copper flash. @ Mating/unmating force 8 oz. per contact, max./0.5 oz. per contact min. Performance Data The table below summarizes the results of key tests perfarmed in accordance with MIL-STD-1344, where applicable. Data is applicable to standard connectors with standard terminations. Variations may affect this data, so please consult the factory for further information on your requirements. Test Method Criteria of Acceptance Dielectric Withstanding Method 3001- Voltage 900 VAC at sea level 300 VAC at 70,000 altitude No breakdown No breakdown Solder Pots and Shielded Cable 600 VAC at sea level 150 VAC at 70,000 altitude No breakdown No breakdown Insulation Resistance Method 3003 Thermal Shock Method 1003, Condition A: 45C to + 125C 5,000 megohms minimum No physical damage Physical Shack Method 2004, Condition E: 50 Gs, 3-axes, 6 millisecond No physical damage No {oss of continuity > 1 psec duration sawtooth pulse Vibration Method 2005, Condition IV: No physical damage 20 G's, 10-2,000 Hz, 12 hrs. No loss of continuity > 1 psec Durability 500 cycles of mating and No mechanical or electrical defects unmating, 500 CPH max. Moisture Resistance Methad 1002, Type Il omit steps 7a & 7b Insulatton resistance > 100 megohms Salt Spray Methad 1001, Condition 8. Shall be capable of mating and unmating, 48 hours and meet contact resistance requirements Contact Resistance Method 307: (MIL-STD-202) At 3 amps 8 millichms maximum At 1 milliamp 10 milliohms maximum Contact Retention Per MIL-C-83513 5 |b. minimum axial load ITT Cannon Micromuniature Products 666 E Qyer Rd, PO Box 929 Santa Ana CA 92702 0929 (714) 557-4700 FAX (714) 754-2142 Dimensions are shown in inches (millimeters) Dimensions subject to change. Mm 9005424 0000585 25Micro-D Metal Shell - .050 Center Spacing MDM Mounting Hardware Views (for sizes 9 51) This hardware supplied unassembled. yf SCREW i MATING: #256UNC2B x aries FACE f Wi BETAS H cup . pb 195 16.20) MAX. NIN eden | teow i RY 1824 62 | NEES N mat ) 688(47.48) 7 PANEL REF a Sioa . wax = F7UT eX i : : t = d ; \ BUSHING rap.) eax, Screw Lock Assembly : \ i bore (0332 36} #258 UNC-2A, =F} | RECOMMENDED dJackpost ~ (P} ~ y* PANEL THICKNESS Screw Leck Assembly* *NOTE: Torque value is 2.5 in /lbs max, 90 Angle Mounting Bracket 096 = .005 (2 44 & OF) DIA. bond 178 & OS wr 170 i452 ot 019} PP Nye 74.38) Max |, A >| 90 Angle Mounting Bracket A B Description Part Number 005 (0.13) Max. Screw Lock Assembly 322-9500-000 N/A Jackpost Kit 320-9505-000 N/A Mounting Bracket 90 MDM 015-9516-002 147 (3.73) 308 (7.82) for 9 thru 37 Shell Sizes Mounting Bracket 90 MOM 015-9516-003 169 (4.29) 350 (8.89) for 51 Shell Size NOTES: Screw lock assembly (322-9500-000} can be used for front mounting only. Jackpost kit (320-9505-000) consists of two assemblies, shipped unassembled Jackpost Bushing (for rear panel mounting-for sizes 9 51) HEX IS 135 (3 43)/ 115(2 92) ACROSS FLATS C tary wat 7Q (4 32), #2-56-UNC-28 THD 105 (2 B7} 785 (4-763 MATING FACE Jarre & TOO ray . BEG 20) R TYP ois) t DA TYP : 3 = TYP gl eee Plug and Receptacle Dimensions ; 5 Shell + 004 (0.10) + 004 (0.10) C Size 000 (0.00) 000 (0.00) ,005 (0.13) 4 401 (10.19) 252 (6.40) 565 (14.35) 15 551 (14.00} 252 (6.40) 715 (18.16) Panel A +08 (0.13) Jackpost Kit a 701 (17 83} .252 (6.40) 865 (21.97) Thickness .000 (0.00) Number* 25 801 (20.34) 252 (6.40) 965 (24.51) 3/32 (2.4) 087 (2.21) 320-9505-007 i 951 (24.16) 252 (6.40) 4.116 (28.34) 1/16 (1.6) 056 (1.42) 320-9505-006 7 1.101 (27.97) 252 {6.40} 1.265 (32.13) 3/64 (1.2) 042 (1.07) 320-9505-005 51 1.051 (26.70) 295 {7.49} 1.218 (30.86) 1/32 (0.8) 025 (0.64) 320-9505-004 *2 jackposts, 2 nuts, 2 washers. 24 ITT Cannon Dimensions are shown in inches (millimeters). Dimensions subject to change Micromintature P oducts 666 E Dyer Rd., PO Box 929, Santa Ana, CA 92702-0929 (714) 557-4700 FAX (714) 754 2142 M@ 9005424 gooos50 bLT mmMicro-D Metal Shell .050 Center Spacing MDM Mounting Hardware Views (sizes 9 51) This hardware is factory installed. 735 (18.67) - MATING CONNECTOR HEX HEAD a4 004 7 AME srownron MAX. SHOWN FOR 050 (1 27) ACROSS FLATS (0 36 +0 1D) ALLOWABLE AEF Outy REF ONLY O50 (1 27) DEEP {REF } DIAMETRAL FLOAT 1804.03 490 te 020 (0 51) MAX ALLOWABLE [Tests on 124 AXIAL FLOAT (12 45) MAX ; #65 j Dy b | 13.94) MAX 185 (4 71 oe H y - 4 wx 098 7 G ares (2 38} Hi Z _ | REF y A ry} T [sun I i 090 +.0015 MATING PART HAS A 040(1 02) 42 29 & 0-038) DIA 031 = 003 #256. PARTHAS A 040(1 02) FAGE MAX, AXIAL FLOAT (0 73 0 08} MATING uNC-24 MAX AXIAL FLOAT #256 FACE UNE-2A Float Mount~ {F} dackscrew~ (K) Standard Jackscrew- (L) Low Profile Shown here 1s a cutaway view of the float mount for the MD connector. The basic shell dimensions are the same for the float mount and the screw mounting hole configurations. View shown ts for standard float mount front panel mounting. Reverse mounting is available on request Repair kit available-consult factory. *NOTE: Torque values are as follows. Low Profile Jackscrew (L}-2 5 in/ lbs Standard Jackscrew (K)-2 5 in/lbs Mounting Hardware to Military Specification (for sizes 9 100) per MIL-C-83513/5 This hardware supplied unassembled #2.56 UNC-2A ai PLUG (REF) WITH THREAD TYP. ED <i .092 (2.54) DIA. =o \ MOUNTING HOLES PLUG (REF} WITH 10 025) #2-56 UNC: 082 (2.94) DIA. 010 (0.25) #256 UNC-2A \ MOUNTING HOLES TH'K REF) i | X POTTING WELL (REF} 361 (917) toe elt MAX, [ i 062 (1.57) HEX. (REF) ee 010 (0,25) \ TH'K (REF) POTTING WELL (REF) Figure 1. dackscrew Low profile Allen Head Figure 2. Jackscrew High Profile Slotted Head Optional Head Configuration Slotted Head Size 9-51 Plug and Receptacle Size 9-51 Low and High Profile Size 9-51 -426 (3.18) HEX | | Size 9-51 Size 100* _| L. 2-56 UNC-26 Thread Description Mod Code Part Number Mod Code Part Number N 190 as) Slotted Head Jackscrew Assy Low Profile (Figure 1) M5 320-9508-025 M15 320-9508-021 : 186 7 Slotted Head Jackscrew Assy High Profile (Figure 2) M6 320-9508-027 M16 320-9508-023 |; peznen $752.08) Allen Heal Jackscrew Assy Low Profile (Figure 1) M2 320-9508-026 M12 320-9508-022 010 (0.25) Allen Head Jackscrew Assy High Profile (Figure 2) M3 320-9508-028 M13 320-9508-024 Jackpost Assy (Figure 3} M7 320-9505-033 M17 320-9505-030 RETAINING NUT 154 (3.91) HEX. Figure 3. Jackpost Assembly Size 9-51 *Size 100 requires B1 size mounting holes. Dimensions are shown in inches {millimeters} TTT Cannon Dimensions subject to change Microminiature Products * 666 E Dyer Rd PO Box 929 Santa Ana, CA 92702-0929 (714) 557-4700 FAX (714) 754-2142 Me 9005424 9000591 SSk mm 25Micro-D Metal Shell .050 Center Spacing Mounting Hardware Views (for size 100) This hardware supplied unassembled. 129 & 095 #4-40 UNC ~28 [ 12291500, f/ THD #440 UNE-2A PANEL +-+-f4}---+ win MAY BE USED WITH Soe aoe #6 LOCK WASHER 093 (2 36) MAX r 4 i THICK PANEL + { cst, 03) $00(12. 70: Oh me $7 | ae \ [ : | $85 (4 70} | 4 MAX 90 Angle Mounting MATING Sing Bracket #3 -40 UNC-28 INNER THD alackpest ~ [P} | $0 Angle Mounting Bracket A B Description Part Number +,005 (0.13) Max. Jackpost Kit 320-9505-015 NIA Mounting Bracket 90 MOM 015-9528-000 191 {4.85} 370 (9.40) This hardware is factory installed. MATING oa ye (036 050 ALL =) se us cownecTOR vastisen raosie ALOE <i} GN FOR : HEX. SOCKET HD, [res we * RF OnLy mas 078 (1.98) ACROSS FLATS 050 (4.97) MIN, DEPTH BARS _ ) 485 (8.94) MAX. MAK os eZ. 4 | a _ ; G40 {1.02} MAX 1. > AXIAL FLOAT ae oo = 23}: OB MATING PART HAS A .040(1 023 BA = 4 (0:76 0.08) FACE eon MAX AXIAL FLOAT sure sine #440 UNC-2A Float Mounting (F} Std. dackscrew ~ (K) Slotted Head: dackscrew ~ {L} (Law Profile} *NOTE: Torque values are as follows: Low Profile Jackscrew (L}4.0 in/tbs Standard Jackscrew (K)-4.0 in/lbs Jackpost Bushing (for Rear Panel Mounting) Dimensions for Rear Panel Mounting ENGAGING FACE cats bast 4.800 + .00S $4-40 UNC-ZB | GS72 + 01) aos A 0.1808, Panel +005 (0.13) Jackpost Kit Thickness 000 (0.00) Number* 464 14.09) - 3/32 (2.4) 087 (2.21) 320-9505-013 758 (a0) 1/16 (1.6} 058 (1.42) 320-9505-012 125: a 1/32 (0.8) 025 (0.64) 320-9505-010 (3.183 3/64 (1.2) 042 (1.07) 320-9505-011 *2 jackposts, 2 nuts, 2 washers ITT Cannon _ Microminiature Praducts * 666 E Dyer Rd, PO Box 929 Santa Ana CA 92702-0929 M 9005424 0000592 492 26 Dimensions are shown in inches (millimeters) Dimensions subject to change (714) 557 4700 FAX (714) 754-2142