LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 LM4951 Wide Voltage Range 1.8 Watt Audio Amplifier Check for Samples: LM4951 FEATURES DESCRIPTION * The LM4951 is an audio power amplifier primarily designed for demanding applications in Portable Handheld devices. It is capable of delivering 1.8W mono BTL to an 8 load, continuous average power, with less than 1% distortion (THD+N) from a 7.5VDC power supply. 1 2 * * * * * Click and Pop Circuitry Eliminates Noise during Turn-On and Turn-Off Transitions Low Current, Active-Low Shutdown Mode Low Quiescent Current Thermal Shutdown Protection Unity-Gain Stable External Gain Configuration Capability APPLICATIONS * * * Portable Handheld Devices up to 9V Cell Phone PDA KEY SPECIFICATIONS * * * * * Wide Voltage Range: 2.7V to 9 V Quiescent Power Supply Current (VDD = 7.5V): 2.5mA (typ) Power Output BTL at 7.5V, 1% THD: 1.8 W (typ) Shutdown Current: 0.01A (typ) Fast Turn on Time: 25ms (typ) Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. The LM4951 does not require bootstrap capacitors, or snubber circuits. The LM4951 features a low-power consumption active-low shutdown mode. Additionally, the LM4951 features an internal thermal shutdown protection mechanism. The LM4951 contains advanced click and pop circuitry that eliminates noises which would otherwise occur during turn-on and turn-off transitions. The LM4951 is unity-gain stable and can be configured by external gain-setting resistors. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2013, Texas Instruments Incorporated LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com Typical Application Rf VDD Cs 1.0 PF VDD Ri 20k Ci 0.39 PF VIN - Vo- AMPA 1k Rc CBYPASS VIH 1.0 PF + CCHG 20k Control Bias Bypass 8: VIL Shutdown control 20k Shutdown + AMPB Vo+ GND * RC is needed for over/under voltage protection. If inputs are less than VDD +0.3V and greater than -0.3V, and if inputs are disabled when in shutdown mode, then RC may be shorted. Figure 1. Typical Bridge-Tied-Load (BTL) Audio Amplifier Application Circuit Connection Diagram + Bypass 1 10 VO Shutdown 2 9 VDD CCHG 3 8 NC NC 4 7 GND VIN 5 6 VO - Figure 2. DPR Package (Top View) See Package Number DPR0010A Vo VIN A Cchg GND B VDD GND SHUTDOWN BYPASS C 1 A. 2 Vo + 3 * DAP can either be soldered to GND or left floating. Figure 3. 9 Bump DSBGA Package (Top View) See Package Number YZR0009AAA 2 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage 9.5V -65C to +150C Storage Temperature -0.3V to VDD + 0.3V Input Voltage (4) Internally limited ESD Susceptibility (5) 2000V ESD Susceptibility (6) 200V Power Dissipation Junction Temperature 150C Thermal Resistance JA (WSON) (4) 52C/W See AN-1187 'Leadless Leadframe Packaging (WSON)' (Literature Number SNOA401) (1) (2) (3) (4) (5) (6) All voltages are measured with respect to the GND pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is P DMAX = (TJMAX - TA) / JA or the given in Absolute Maximum Ratings, whichever is lower. For the LM4951 typical application (shown in Figure 1) with VDD = 7.5V, RL = 8 mono-BTL operation the max power dissipation is 1.42W. JA = 73C/W. Human body model, 100pF discharged through a 1.5k resistor. Machine Model, 220pF-240pF discharged through all pins. Operating Ratings Temperature Range TMIN TA TMAX -40C T A +85C 2.7V VDD 9V Supply Voltage Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 3 LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com Electrical Characteristics VDD = 7.5V (1) (2) The following specifications apply for VDD = 7.5V, AV-BTL = 6dB, RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol Parameter Conditions LM4951 Typical (3) Limit (4) (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A,RL = 8 2.5 4.5 ISD Shutdown Current VSHUTDOWN = GND (6) 0.01 5 mA (max) A (max) VOS Offset Voltage 5 30 mV (max) VSDIH Shutdown Voltage Input High 1.2 V (min) VSDIL Shutdown Voltage Input Low Rpulldown Pulldown Resistor on S/D TWU Wake-up Time CB = 1.0F Tsd Shutdown time CB = 1.0F 0.4 V (max) 75 45 k (min) 25 35 ms 10 ms (max) 170 150 190 C (min) C (max) TSD Thermal Shutdown Temperature PO Output Power THD = 1% (max); f = 1kHz RL = 8 Mono BTL 1.8 1.5 W (min) THD+N Total Harmomic Distortion + Noise PO = 600mWrms; f = 1kHz AV-BTL = 6dB 0.07 0.5 % (max) THD+N Total Harmomic Distortion + Noise PO = 600mWrms; f = 1kHz AV-BTL = 26dB 0.35 % OS Output Noise A-Weighted Filter, Ri = Rf = 20k Input Referred, Note 10 10 V PSRR Power Supply Rejection Ratio VRIPPLE = 200mVp-p, f = 217Hz, CB = 1.0F, Input Referred 66 (1) (2) (3) (4) (5) (6) 4 56 dB (min) All voltages are measured with respect to the GND pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25C and represent the parametric norm. Limits are specified to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Shutdown current is measured in a normal room environment. The Shutdown pin should be driven as close as possible to GND for minimum shutdown current. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 Electrical Characteristics VDD = 3.3V (1) (2) The following specifications apply for VDD = 3.3V, AV-BTL = 6dB, RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol Parameter Conditions LM4951 Typical (3) Limit (4) (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A,RL = 8 2.5 4.5 ISD Shutdown Current VSHUTDOWN = GND (6) 0.01 2 A (max) VOS Offset Voltage 3 30 mV (max) VSDIH Shutdown Voltage Input High 1.2 V (min) VSDIL Shutdown Voltage Input Low TWU Wake-up Time CB = 1.0F Tsd Shutdown time CB = 1.0F PO Output Power THD = 1% (max); f = 1kHz RL = 8 Mono BTL THD+N Total Harmomic Distortion + Noise1 THD+N 0.4 25 mA (max) V (max) ms (max) 10 ms (max) 280 230 mW (min) PO = 100mWrms; f = 1kHz AV-BTL = 6dB 0.07 0.5 % (max) Total Harmomic Distortion + Noise1 PO = 100mWrms; f = 1kHz AV-BTL = 26dB 0.35 % OS Output Noise A-Weighted Filter, Ri = Rf = 20k Input Referred, Note 10 10 V PSRR Power Supply Rejection Ratio VRIPPLE = 200mVp-p, f = 217Hz, CB = 1F, Input Referred 71 (1) (2) (3) (4) (5) (6) 61 dB (min) All voltages are measured with respect to the GND pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not specified for parameters where no limit is given, however, the typical value is a good indication of device performance. Typicals are measured at 25C and represent the parametric norm. Limits are specified to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are specified by design, test, or statistical analysis. Shutdown current is measured in a normal room environment. The Shutdown pin should be driven as close as possible to GND for minimum shutdown current. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 5 LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics 10 THD+N vs Frequency VDD = 3.3V, PO = 100mW, AV = 6dB 10 THD+N vs Frequency VDD = 3.3V, PO = 100mW, AV = 26dB 5 2 1 THD+N (%) THD+N (%) 1 0.5 0.2 0.1 0.1 0.05 0.02 0.01 20 200 2k 0.01 20 20k Figure 5. THD+N vs Frequency VDD = 5V, PO = 400mW, AV = 6dB THD+N vs Frequency VDD = 5V, PO = 400mW, AV = 26dB 10 5 5 2 2 1 1 0.5 0.2 0.5 0.2 0.1 0.1 0.05 0.05 0.02 0.02 0.01 20 50 100 200 500 1k 2k 0.01 20 5k 10k 20k FREQUENCY (Hz) 10 5k 10k 20k Figure 4. THD+N (%) THD+N (%) 10 50 100 200 500 1k 2k FREQUENCY (Hz) FREQUENCY (Hz) 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 6. Figure 7. THD+N vs Frequency VDD = 7.5V, PO = 600mW, AV = 6dB THD+N vs Frequency VDD = 7.5V, PO = 600mW, AV = 26dB 10 5 5 2 THD+N (%) THD+N (%) 1 0.5 0.2 0.1 2 1 0.5 0.05 0.2 0.02 0.01 20 0.1 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) 200 2k 20k FREQUENCY (Hz) Figure 8. 6 20 Figure 9. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 Typical Performance Characteristics (continued) 10 THD+N vs Output Power VDD = 3.3V, f = 1kHz, AV = 6dB THD+N vs Output Power VDD = 3.3V, f = 1kHz, AV = 26dB 10 1 THD+N (%) THD+N (%) 5 0.1 2 1 0.5 0.2 0.01 30m 10m 0.1 10m 500m 100m 20m OUTPUT POWER (W) 30m 50m 70m 100m 300m 500m 40m 60m 80m 200m 400m OUTPUT POWER (W) 10 Figure 10. Figure 11. THD+N vs Output Power VDD = 5V, f = 1kHz, AV = 6dB THD+N vs Output Power VDD = 5V, f = 1kHz, AV = 26dB 10 5 5 2 THD+N (%) THD+N (%) 1 0.5 0.2 0.1 2 1 0.5 0.05 0.2 0.02 0.01 10m 20m 50m 100m 200m 500m 0.1 10m 20m 1 OUTPUT POWER (W) 10 50m 100m 200m 500m 1 OUTPUT POWER (W) Figure 12. Figure 13. THD+N vs Output Power VDD = 7.5V, f = 1kHz, AV = 6dB THD+N vs Output Power VDD = 7.5V, f = 1kHz, AV = 26dB 10 5 5 1 THD+N (%) THD+N (%) 2 0.5 0.2 0.1 2 1 0.5 0.05 0.2 0.02 0.01 10m 20m 50m 100m 200m 500m 1 2 3 0.1 10m 20m 50m 100m 200m 500m 1 2 3 OUTPUT POWER (W) OUTPUT POWER (W) Figure 14. Figure 15. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 7 LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) Power Supply Rejection vs Frequency VDD = 3.3V, AV = 6dB, VRIPPLE = 200mVP-P Input Terminated into 10 Power Supply Rejection vs Frequency VDD = 3.3V, AV = 26dB, VRIPPLE = 200mVP-P Input Terminated into 10 +0 -10 -20 PSRR (dB) PSRR (dB) -30 -40 -50 -60 -70 -80 -90 -100 20 50 100 200 500 1k 2k +0 -2.5 -5 -7.5 -10 -12.5 -15 -17.5 -20 -22.5 -25 -27.5 -30 -32.5 -35 -37.5 -40 -42.5 -45 -47.5 -50 -52.5 -55 -57.5 -60 20 5k 10k 20k Figure 16. Figure 17. Power Supply Rejection vs Frequency VDD = 5V, AV = 6dB, VRIPPLE = 200mVP-P Input Terminated into 10 Power Supply Rejection vs Frequency VDD = 5V, AV = 26dB, VRIPPLE = 200mVP-P Input Terminated into 10 +0 -10 -20 PSRR (dB) PSRR (dB) -30 -40 -50 -60 -70 -80 -90 -100 20 50 100 200 500 1k 2k +0 -2.5 -5 -7.5 -10 -12.5 -15 -17.5 -20 -22.5 -25 -27.5 -30 -32.5 -35 -37.5 -40 -42.5 -45 -47.5 -50 -52.5 -55 -57.5 -60 20 5k 10k 20k 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 18. Figure 19. Power Supply Rejection vs Frequency VDD = 7.5V, AV = 6dB, VRIPPLE = 200mVP-P Input Terminated into 10 Power Supply Rejection vs Frequency VDD = 7.5V, AV = 26dB, VRIPPLE = 200mVP-P Input Terminated into 10 +0 -10 -20 PSRR (dB) -30 PSRR (dB) 5k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) -40 -50 -60 -70 -80 -90 -100 20 50 100 200 500 1k 2k 5k 10k 20k +0 -2.5 -5 -7.5 -10 -12.5 -15 -17.5 -20 -22.5 -25 -27.5 -30 -32.5 -35 -37.5 -40 -42.5 -45 -47.5 -50 -52.5 -55 -57.5 -60 20 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 20. 8 50 100 200 500 1k 2k Figure 21. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 Typical Performance Characteristics (continued) Noise Floor VDD = 3.3V, AV = 6dB, Ri = Rf = 20k BW < 80kHz, A-weighted Noise Floor VDD = 3V, AV = 26dB, Ri = 20k, Rf = 200k BW < 80kHz, A-weighted 30P OUTPUT NOISE VOLTAGE (V) OUTPUT NOISE VOLTAGE (V) 50P 40P 20P 10P 9P 8P 7P 6P 5P 4P 3P 2P 150P 120P 100P 95P 90P 85P 82P 75P 72P 65P 62P 55P 52P 50P 1P 20 50 100 200 500 1k 2k 20 5k 10k 20k 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 22. Figure 23. Noise Floor VDD = 5V, AV = 6dB, Ri = Rf = 20k BW < 80kHz, A-weighted Noise Floor VDD = 5V, AV = 26dB, Ri = 20k, Rf = 200k BW < 80kHz, A-weighted 30P OUTPUT NOISE VOLTAGE (V) OUTPUT NOISE VOLTAGE (V) 50P 40P 20P 10P 9P 8P 7P 6P 5P 4P 3P 2P 120P 100P 95P 90P 85P 82P 75P 72P 65P 62P 55P 52P 50P 1P 20 150P 50 100 200 500 1k 2k 20 5k 10k 20k 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 24. Figure 25. Noise Floor VDD = 7.5V, AV = 6dB, Ri = Rf = 20k BW < 80kHz, A-weighted Noise Floor VDD = 7.5V, AV = 26dB, Ri = 20k, Rf = 200k BW < 80kHz, A-weighted 30P OUTPUT NOISE VOLTAGE (V) OUTPUT NOISE VOLTAGE (V) 50P 40P 20P 10P 9P 8P 7P 6P 5P 4P 3P 2P 120P 100P 95P 90P 85P 82P 75P 72P 65P 62P 55P 52P 50P 1P 20 150P 50 100 200 500 1k 2k 5k 10k 20k 20 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) FREQUENCY (Hz) Figure 26. Figure 27. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 9 LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) Power Dissipation vs Output Power VDD = 3.3V, RL = 8, f = 1kHz Power Dissipation vs Output Power VDD = 7.5V, RL = 8, f = 1kHz 1600 300 POWER DISSIPATION (mW) POWER DISSIPATION (mW) 1400 250 200 150 100 1200 1000 800 600 400 200 50 0 0 0 0 50 100 150 200 250 200 400 600 800 1000 1200 1400 OUTPUT POWER (mW) 300 OUTPUT POWER (mW) Figure 28. Figure . Supply Current vs Supply Voltage RL = 8, VIN = 0V, Rsource = 50 Clipping Voltage vs Supply Voltage RL = 8, from top to bottom: Negative Voltage Swing; Positive Voltage Swing 1.4 2.5 DROPOUT VOPLTAGE (V) SUPPLY CURRENT (mA) 1.2 2 1.5 1 0.5 1 0.8 0.6 0.4 0.2 0 0 2 3 4 5 6 7 8 9 0 10 2 SUPPLY VOLTAGE (V) 6 8 10 Figure 30. Output Power vs Supply Voltage RL = 8, from top to bottom: THD+N = 10%, THD+N = 1% Output Power vs Load Resistance VDD = 3.3V, f = 1kHz from top to bottom: THD+N = 10%, THD+N = 1% 4 450 3.5 400 OUTPUT POWER (mW) OUTPUT POWER (mW) Figure 29. 3 2.5 2 1.5 1 0.5 350 300 250 200 150 100 50 0 0 2.7 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 0 20 40 60 80 100 LOAD RESISTANCE (W) SUPPLY VOLTAGE (V) Figure 31. 10 4 SUPPLY VOLTAGE (V) Figure 32. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 Typical Performance Characteristics (continued) Output Power vs Load Resistance VDD = 7.5V, f = 1kHz from top to bottom: THD+N = 10%, THD+N = 1% Frequency Response vs Input Capacitor Size RL = 8 from top to bottom: Ci = 1.0F, Ci = 0.39F, Ci = 0.039F 3000 20 2500 12 OUTPUT LEVEL (dB) OUTPUT POWER (mW) 16 2000 1500 1000 8 4 0 -4 -8 -12 -16 -20 500 -24 -28 0 8 16 32 48 64 80 20 96 112 LOAD RESISTANCE (W) 50 100 200 500 1k 2k 5k 10k 20k FREQUENCY (Hz) Figure 33. Figure 34. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 11 LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com APPLICATION INFORMATION HIGH VOLTAGE BOOMER Unlike previous 5V Boomer amplifiers, the LM4951 is designed to operate over a power supply voltages range of 2.7V to 9V. Operating on a 7.5V power supply, the LM4951 will deliver 1.8W into an 8 BTL load with no more than 1% THD+N. BRIDGE CONFIGURATION EXPLANATION As shown in Figure 1, the LM4951 consists of two operational amplifiers that drive a speaker connected between their outputs. The value of input and feedback resistors determine the gain of each amplifier. External resistors Ri and Rf set the closed-loop gain of AMPA, whereas two 20k internal resistors set AMPB's gain to -1. The LM4951 drives a load, such as a speaker, connected between the two amplifier outputs, VO+ and VO -. Figure 1 shows that AMPA's output serves as AMPB's input. This results in both amplifiers producing signals identical in magnitude, but 180 out of phase. Taking advantage of this phase difference, a load is placed between AMPA and AMPB and driven differentially (commonly referred to as "bridge mode"). This results in a differential, or BTL, gain of AVD = 2(Rf/ Ri) (1) Bridge mode amplifiers are different from single-ended amplifiers that drive loads connected between a single amplifier's output and ground. For a given supply voltage, bridge mode has a distinct advantage over the singleended configuration: its differential output doubles the voltage swing across the load. Theoretically, this produces four times the output power when compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited and that the output signal is not clipped. To ensure minimum output signal clipping when choosing an amplifier's closed-loop gain, refer to the AUDIO POWER AMPLIFIER DESIGN section. Under rare conditions, with unique combinations of high power supply voltage and high closed loop gain settings, the LM4951 may exhibit low frequency oscillations. Another advantage of the differential bridge output is no net DC voltage across the load. This is accomplished by biasing AMP1's and AMP2's outputs at half-supply. This eliminates the coupling capacitor that single supply, single-ended amplifiers require. Eliminating an output coupling capacitor in a typical single-ended configuration forces a single-supply amplifier's half-supply bias voltage across the load. This increases internal IC power dissipation and may permanently damage loads such as speakers. POWER DISSIPATION Power dissipation is a major concern when designing a successful bridged amplifier. The LM4951's dissipation when driving a BTL load is given by Equation (2). For a 7.5V supply and a single 8 BTL load, the dissipation is 1.42W. PDMAX-MONOBTL = 4(VDD) 2/ 22RL: Bridge Mode (2) The maximum power dissipation point given by Equation (2) must not exceed the power dissipation given by Equation (3): PDMAX' = (TJMAX - TA) / JA (3) The LM4951's TJMAX = 150C. In the DPR package, the LM4951's JA is 73C/W when the metal tab is soldered to a copper plane of at least 1in2. This plane can be split between the top and bottom layers of a two-sided PCB. Connect the two layers together under the tab with an array of vias. At any given ambient temperature TA, use Equation (3) to find the maximum internal power dissipation supported by the IC packaging. Rearranging Equation (3) and substituting PDMAX for PDMAX' results in Equation (4). This equation gives the maximum ambient temperature that still allows maximum stereo power dissipation without violating the LM4951's maximum junction temperature. TA = TJMAX - PDMAX-MONOBTLJA (4) For a typical application with a 7.5V power supply and a BTL 8 load, the maximum ambient temperature that allows maximum stereo power dissipation without exceeding the maximum junction temperature is approximately 46C for the TS package. 12 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 TJMAX = PDMAX-MONOBTLJA + TA (5) Equation (5) gives the maximum junction temperature TJMAX. If the result violates the LM4951's 150C, reduce the maximum junction temperature by reducing the power supply voltage or increasing the load resistance. Further allowance should be made for increased ambient temperatures. The above examples assume that a device is operating around the maximum power dissipation point. Since internal power dissipation is a function of output power, higher ambient temperatures are allowed as output power or duty cycle decreases. If the result of Equation 2 is greater than that of Equation (3), then decrease the supply voltage, increase the load impedance, or reduce the ambient temperature. Further, ensure that speakers rated at a nominal 8 do not fall below 6. If these measures are insufficient, a heat sink can be added to reduce JA. The heat sink can be created using additional copper area around the package, with connections to the ground pins, supply pin and amplifier output pins. Refer to the Typical Performance Characteristics curves for power dissipation information at lower output power levels. POWER SUPPLY VOLTAGE LIMITS Continuous proper operation is ensured by never exceeding the voltage applied to any pin, with respect to ground, as listed in the Absolute Maximum Ratings section. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. Applications that employ a voltage regulator typically use a 10F in parallel with a 0.1F filter capacitors to stabilize the regulator's output, reduce noise on the supply line, and improve the supply's transient response. However, their presence does not eliminate the need for a local 1.0F tantalum bypass capacitance connected between the LM4951's supply pins and ground. Do not substitute a ceramic capacitor for the tantalum. Doing so may cause oscillation. Keep the length of leads and traces that connect capacitors between the LM4951's power supply pin and ground as short as possible. Connecting a larger capacitor, CBYPASS, between the BYPASS pin and ground improves the internal bias voltage's stability and improves the amplifier's PSRR. The PSRR improvements increase as the bypass pin capacitor value increases. Too large, however, increases turn-on time and can compromise the amplifier's click and pop performance. The selection of bypass capacitor values, especially CBYPASS, depends on desired PSRR requirements, click and pop performance (as explained in the section, SELECTING EXTERNAL COMPONENTS), system cost, and size constraints. MICRO-POWER SHUTDOWN The LM4951 features an active-low micro-power shutdown mode. When active, the LM4951's micro-power shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The low 0.01A typical shutdown current is achieved by applying a voltage to the SHUTDOWN pin that is as near to GND as possible. A voltage that is greater than GND may increase the shutdown current. There are a few methods to control the micro-power shutdown. These include using a single-pole, single-throw switch (SPST), a microprocessor, or a microcontroller. When using a switch, connect the SPST switch between the shutdown pin and VDD. Select normal amplifier operation by closing the switch. Opening the switch applies GND to the SHUTDOWN pin activating micro-power shutdwon.The switch and internal pull-down resistor ensures that the SHUTDOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor or a microcontroller, use a digital output to apply the active-state voltage to the SHUTDOWN pin. SELECTING EXTERNAL COMPONENTS Input Capacitor Value Selection Two quantities determine the value of the input coupling capacitor: the lowest audio frequency that requires amplification and desired output transient suppression. As shown in Figure 1, the input resistor (Ri) and the input capacitor (Ci) produce a high pass filter cutoff frequency that is found using Equation 6. fc = 1/2RiCi (6) Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 13 LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com As an example when using a speaker with a low frequency limit of 50Hz, Ci, using Equation (6) is 0.159F. The 0.39F CINA shown in Figure 1 allows the LM4951 to drive high efficiency, full range speaker whose response extends below 30Hz. Selecting Value For RC The LM4951 is designed for very fast turn on time. The Cchg pin allows the input capacitors (CinA and CinB) to charge quickly to improve click/pop performance. Rchg1 and Rchg2 protect the Cchg pins from any over/under voltage conditions caused by excessive input signal or an active input signal when the device is in shutdown. The recommended value for Rchg1 and Rchg2 is 1k. If the input signal is less than VDD+0.3V and greater than -0.3V, and if the input signal is disabled when in shutdown mode, Rchg1 and Rchg2 may be shorted out. OPTIMIZING CLICK AND POP REDUCTION PERFORMANCE The LM4951 contains circuitry that eliminates turn-on and shutdown transients ("clicks and pops"). For this discussion, turn-on refers to either applying the power supply voltage or when the micro-power shutdown mode is deactivated. As the VDD/2 voltage present at the BYPASS pin ramps to its final value, the LM4951's internal amplifiers are configured as unity gain buffers. An internal current source charges the capacitor connected between the BYPASS pin and GND in a controlled manner. Ideally, the input and outputs track the voltage applied to the BYPASS pin. The gain of the internal amplifiers remains unity until the voltage on the bypass pin reaches VDD/2. As soon as the voltage on the bypass pin is stable, there is a delay to prevent undesirable output transients ("click and pops"). After this delay, the device becomes fully functional. AUDIO POWER AMPLIFIER DESIGN Audio Amplifier Design: Driving 1.8W into an 8 BTL The following are the desired operational parameters: Power Output 1.8WRMS Load Impedance 8 Input Level 0.3VRMS (max) Input Impedance 20k Bandwidth 50Hz-20kHz 0.25dB The design begins by specifying the minimum supply voltage necessary to obtain the specified output power. One way to find the minimum supply voltage is to use the Equation (7) curve in the Typical Performance Characteristics section. Another way, using Equation 7, is to calculate the peak output voltage necessary to achieve the desired output power for a given load impedance. To account for the amplifier's dropout voltage, two additional voltages, based on the Figure 30 in the Typical Performance Characteristics curves, must be added to the result obtained by Equation (7). The result is Equation (8). (7) (8) VDD = VOUTPEAK + VODTOP + VODBOT The commonly used 7.5V supply voltage easily meets this. The additional voltage creates the benefit of headroom, allowing the LM4951 to produce peak output power in excess of 1.8W without clipping or other audible distortion. The choice of supply voltage must also not create a situation that violates of maximum power dissipation as explained above in the POWER DISSIPATION section. After satisfying the LM4951's power dissipation requirements, the minimum differential gain needed to achieve 1.8W dissipation in an 8 BTL load is found using Equation (9). (9) Thus, a minimum gain of 12.6 allows the LM4951's to reach full output swing and maintain low noise and THD+N performance. For this example, let AV-BTL = 13. The amplifier's overall BTL gain is set using the input (Ri) and feedback (Rf) resistors of the first amplifier in the series BTL configuration. Additionaly, AV-BTL is twice the gain set by the first amplifier's Ri and Rf. With the desired input impedance set at 20k, the feedback resistor is found using Equation (10). 14 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 Rf/ Ri = AV-BTL/ 2 (10) The value of Rf is 130k (choose 191k, the closest value). The nominal output power is 1.8W. The last step in this design example is setting the amplifier's -3dB frequency bandwidth. To achieve the desired 0.25dB pass band magnitude variation limit, the low frequency response must extend to at least one-fifth the lower bandwidth limit and the high frequency response must extend to at least five times the upper bandwidth limit. The gain variation for both response limits is 0.17dB, well within the 0.25dB-desired limit. The results are an fL = 50Hz / 5 = 10Hz (11) and an fL = 20kHz x 5 = 100kHz (12) As mentioned in the SELECTING EXTERNAL COMPONENTS section, Ri and Ci create a highpass filter that sets the amplifier's lower bandpass frequency limit. Find the coupling capacitor's value using Equation (13). Ci = 1 / 2RifL (13) The result is 1 / (2x20kx10Hz) = 0.795F (14) Use a 0.82F capacitor, the closest standard value. The product of the desired high frequency cutoff (100kHz in this example) and the differential gain AVD, determines the upper passband response limit. With AVD = 7 and fH = 100kHz, the closed-loop gain bandwidth product (GBWP) is 700kHz. This is less than the LM4951's 3.5MHz GBWP. With this margin, the amplifier can be used in designs that require more differential gain while avoiding performance restricting bandwidth limitations. RECOMMENDED PRINTED CIRCUIT BOARD LAYOUT Figures 6-8 show the recommended two-layer PC board layout that is optimized for the DPR0010A. This circuit is designed for use with an external 7.5V supply 8 (min) speakers. These circuit boards are easy to use. Apply 7.5V and ground to the board's VDD and GND pads, respectively. Connect a speaker between the board's OUTA and OUTB outputs. Demonstration Board Layout Figure 35. Recommended TS SE PCB Layout: Top Silkscreen Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 15 LM4951 SNAS244N - AUGUST 2004 - REVISED MAY 2013 www.ti.com Figure 36. Recommended TS SE PCB Layout: Top Layer Figure 37. Recommended TS SE PCB Layout: Bottom Layer Revision History 16 Rev Date 1.0 8/25/04 Initial WEB. 1.1 10/19/05 Added the DSBGA pkg, then WEB. Submit Documentation Feedback Description Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 LM4951 www.ti.com SNAS244N - AUGUST 2004 - REVISED MAY 2013 Rev Date Description 1.2 08/30/06 Added the Limit value (=35) on the Twu (7.5V Elect Char table), then WEB. 1.3 09/11/06 Added the "Selecting Value For Rc, then WEB. 1.4 05/21/07 Fixed a typo ( X3 value = 0.6000.075) instead of (X3 = 0.6000.75). 1.5 03/18/09 Text edits. N 05/03/13 Changed layout of National Data Sheet to TI format. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4951 17 PACKAGE OPTION ADDENDUM www.ti.com 14-Feb-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM4951SD/NOPB ACTIVE WSON DPR 10 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM L4951SD LM4951SDX/NOPB ACTIVE WSON DPR 10 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM L4951SD (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 14-Feb-2014 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM4951SD/NOPB WSON DPR 10 1000 178.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 LM4951SDX/NOPB WSON DPR 10 4500 330.0 12.4 4.3 4.3 1.3 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4951SD/NOPB WSON DPR 10 1000 210.0 185.0 35.0 LM4951SDX/NOPB WSON DPR 10 4500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA DPR0010A SDC10A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4951SD LM4951SD/NOPB LM4951SDX LM4951SDX/NOPB LM4951TL/NOPB LM4951TLX/NOPB