FTR-K1 SERIES POWER RELAY 1 POLE - 5A/10A Medium Load Control JV Series n FEATURES UL, CSA, VDE, SEMKO, CQC recognized UL class B (130C) wire class l Low profile and space saving - Height: 12.5 mm - Mounting space: 175 mm2 l High sensitivity in small package - Operating power: 0.112 to 0.13 W - Nominal power: 0.2 to 0.3 W l High insulation with reinforced insulation system (between coil and contacts) - Insulation distance: 8 mm - Dielectric strength: 5,000 VAC - Surge strength: 10,000 V l Plastic materials - UL94 flame class V-0 -UL CTI level class 2 l Plastic sealed type, RTIII l RoHS compliant. Please see page 7 for more information l l n PARTNUMBER INFORMATION [Example] (a) JV - 12 (a) (*) (b) S - K T (c) (d) (e) Relay type JV : JV-Series (b) Coil rated voltage 12 : 3.....48 VDC Coil rating table at page 3 (c) Coil type Nil S : Standard type (300mW) (not for -KS type) : High sensitive type (200mW) (-KS type: 250mW) K : Plastic sealed type, RTIII T S : High density mounting type : High power type 10A (d) Enclosure (f) Construction Note: Actual marking omits the hyphen (-) of (*) 1 FTR-K1 JV SERIES SERIES n SPECIFICATION Item Contact Data Life Coil Data Timing Data Insulation High sensitive type High power type JV - ( ) JV - ( ) S JV- ( ) - KS Configuration 1 form A (SPST-NO) Construction Single Material Silver alloy AgNi + Au Resistance (Initial) Max. 70 m at 6 VDC, 1 A Contact rating 5A, 250VAC / 30VDC (resistive load) 10A, 250VAC / 24VDC Max. carrying current 5A 10A Max. switching voltage 250VAC / 150 VDC Max. switching power 1,250VA / 150W 2,500VA / 240W Max. switching current 5A 10A Min. switching load * 100 mA, 5 VDC Mechanical Min. 5 x 106 operations Electrical Min. 100 x 103 operations Min. 50 x 103 operations Rated power (at 20 C) 300mW 200mW 250mW Operate power (at 20 C) 130mW 113mW 145mW Operating temperature range -40 C to +70 C (no frost) Operate (at nominal voltage) Max. 8 ms (without bounce) Release (at nominal voltage) Max. 4 ms (no diode) Resistance (initial) Min 1,000M at 500VDC Dielectric strength Surge strength Other Standard type Vibration resistance Shock AgSnO2 + Au -40 C to +85C (no frost) Open contacts 750VAC, 1 min. Contacts to coil 5,000VAC, 1 min. Coil to contacts 10,000V / 1.2 x 50s standard wave Misoperation 10 to 55Hz double amplitude 1.65 mm Endurance 10 to 55Hz double amplitude 5 mm Misoperation Min. 100m/s (11 1ms) Endurance Min. 1,000m/s (6 1ms) Weight Approximately 4.3 g Sealing Plastic sealed RTIII * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1 JV SERIES SERIES n COIL RATING Standard type (300 mW) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 3 3 30 1.98 0.15 5 5 83.3 3.3 0.25 6 6 120 3.96 0.3 9 9 270 5.94 0.45 12 12 480 7.9 0.6 24 24 1,920 15.8 1.2 48 48 7,680 31.7 2.4 Rated Power (mW) 300 mW High sensitive type (200 mW) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 3 3 45 2.25 0.15 5 5 125 3.75 0.25 6 6 180 4.5 0.3 9 9 405 6.75 0.45 12 12 720 9 0.6 18 18 1,620 13.5 0.9 24 24 2,880 18 1.2 Rated Power (mW) 200 mW 10A High power type (250 mW) Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 3 3 36 2.1 0.3 5 5 100 3.5 0.5 6 6 144 4.2 0.6 9 9 324 6.3 0.9 12 12 576 8.4 1.2 18 18 1,296 12.6 1.8 24 24 2,304 14.9 2.4 Rated Power (mW) 250 mW Note: All values in the tables are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. 3 FTR-K1 JV SERIES SERIES n SAFETY STANDARDS Type Compliance Contact rating UL UL 508, UL 873 Flammability: UL 94-V0 (plastics) E56140 5A, 250 VAC / 30 VDC (resistive) 1/8 HP, 125VAC/250VAC Pilot duty: C300 CSA C22.2 No. 14 LR 35579 VDE 0435, 0631, 0700 40016247 5A, 250VAC (cos1), 100K 2A, 250VAC (cos 0.4), 100K 5A, 30VDC (omsec), 100K 10A, 250VAC (cos1), JV-KS, 25K 10A, 30VDC (0msec), JV-KS, 100K Also complies with SEMKO, CQC. Please contact sales office when SEMKO, CQC logo marking is neccessary on the cover. n CHARACTERISTIC DATA 4 FTR-K1 JV SERIES SERIES 5 FTR-K1 JV SERIES SERIES n DIMENSIONS JV-KT type + JV-( )S-KS l Dimensions l Schematics (BOTTOM VIEW) l PC board mounting hole layout (BOTTOM VIEW) Unit: mm 6 FTR-K1 JV SERIES SERIES RoHS Compliance and Lead Free Information 1. General Information l l l l All signal and power relays produced by Fujitsu Components are compliant with RoHS directive 2002/95EC including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives on October 21st, 2005. (Amendment to Directive 2002/95/EC) All of our signal and power relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/us/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Profile l Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder condition: Pre-heating: Soldering: maximum 120C dip within 5 sec. at 260C solder bath Solder by Soldering Iron: Soldering Iron Temperature: Duration: maximum 360C maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity l Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers l Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 7 FTR-K1JV SERIES SERIES Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Gotanda-Chuo Building 3-5, Higashigotanda 2-chome, Shinagawa-ku Tokyo 141, Japan Tel: (81-3) 5449-7010 Fax: (81-3) 5449-2626 Email: promothq@ft.ed.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 250 E. Caribbean Drive Sunnyvale, CA 94089 U.S.A. Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2012 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. April 25, 2012 8