Snap Action Switch V General Purpose Snap Action Switch * Industry standard design with switching currents of 10A to 21A * Widely used for applications where long life expectancy and high reliability is required. * Choose from a variety of levers, terminals and operating forces. * Right and Left Barrier options are available for the V-21 and V-16 models * Heat resistant versions of the V-15 and V-10 are available. * RoHS Compliant Ordering Information Model Number Legend V- 1 2 3 1. 2. 3. 4 5 6 7 Ratings 21: 21 A at 250 VAC 16: 16 A at 250 VAC 15: 15 A at 250 VAC 11: 11 A at 250 VAC 10: 10 A at 250 VAC Contact Gap None: 1 mm (F gap) G: 0.5 mm (G gap) Actuator None: Pin plunger 1: Short hinge lever 2: Hinge lever 3: Long hinge lever 4: Simulated roller lever 5: Short hinge roller lever 6: Hinge roller lever 8 9 4. Contact Form COM Terminal, Bottom position: 1: SPDT 2: SPST-NC 3: SPST-NO COM Terminal, Side position: 4: SPDT 5: SPST-NC 6: 5. 7. Note: These OF values are for the pin plunger models. 8. Special Purpose None: Standard T: Heat resistive (V-15 and V-10, only) SPST-NO Terminals A: Solder terminals C2: Quick-connect terminal (#187) C: Quick-connect terminal (#250) Maximum Operating Force 6: 400 gf 5: 200 gf 4: 100 gf 9. Mounting Hole Size None: 3.1 mm K: 2.9 mm 6. Insulation Barrier None: Without Barrier R: Right-hand barrier L: Left-hand barrier (Barriers available for V-21 and V-16, only) Note: Consult Omron regarding nominclature combinations and part numbers not found in this datasheet. Snap Action Switch V 121 Available Combinations Thermoplastic case V-21 V-16 V-11 V-15 V-10 Rated Current 21 A 16 A 11 A 15 A 10 A OF COM Insulation Heat terminal Barrier Resistance Terminal Symbol position Bottom No Standard (80C) Heat resistant (150C) Yes Side No Standard (80C) Standard (80C) Thermosetting case Model 400 gf 400 gf 200 gf 100 gf 400 gf 200 gf 200 gf 100 gf Solder terminals (A) --- Quick-connect terminals (#187)(C2) --- Quick-connect terminals (#250)(C) Solder terminals (A) --- --- --- --- Quick-connect terminals (#187)(C2) --- --- --- --- Quick-connect terminals (#250)(C) --- --- --- --- --- --- --- --- Solder terminals (A) --- --- --- --- --- --- Quick-connect terminals (#187)(C2) --- --- --- --- --- --- Quick-connect terminals (#250)(C) --- --- --- --- --- Solder terminals (A) --- --- --- --- Quick-connect terminals (#187)(C2) --- --- --- --- Quick-connect terminals (#250)(C) --- --- --- --- --- --- --- Note: 1. : Available model. Consult OMRON for specific models with standard approval. List of Models Thermoplastic Case 21 A (OF: 400 gf) Without barrier Common terminal Contact position form Bottom SPDT SPST-NC Right-hand barrier Without barrier Left-hand barrier Terminal style Actuator Quick-connect (#250) (C) Pin plunger SPST-NO SPDT V-21-1C6 V-21-1CR6 V-21-1CL6 V-21-2C6 V-21-2CR6 V-21-2CL6 V-21-3C6 V-21-3CR6 V-21-3CL6 Short hinge lever V-211-1C6 V-211-1CR6 V-211-1CL6 Hinge lever V-212-1C6 V-212-1CR6 V-212-1C6 Long hinge lever V-213-1C6 V-213-1CR6 V-213-1CL6 Simulated roller lever V-214-1C6 V-214-1CR6 V-214-1CL6 Short hinge roller lever V-215-1C6 V-215-1CR6 V-215-1CL6 Hinge roller lever V-216-1C6 V-216-1CR6 V-216-1CL6 Note: 1. Add "G" to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add "-K" to the part number in the appropriate location to obtain 2.9 mm mounting holes. Example: V-21G2-1C6-K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. 122 Snap Action Switch V 16 A (OF: 200 gf) Without barrier Common terminal Contact position form Bottom SPDT SPST-NC SPST-NO SPDT Terminal style A C2 C A C2 C A C2 C A C2 C A C2 C A C2 C A C2 C A C2 C A C2 C Left-hand barrier Right-hand barrier Without barrier Actuator Pin plunger Short hinge lever Hinge lever Long hinge lever Simulated roller lever Short hinge roller lever Hinge roller lever V-16-1A5 V-16-1C25 V-16-1C5 V-16-2A5 V-16-2C25 V-16-2C5 V-16-3A5 V-16-3C25 V-16-3C5 V-161-1A5 V-161-1C25 V-161-1C5 V-162-1A5 V-162-1C25 V-162-1C5 V-163-1A5 V-163-1C25 V-163-1C5 V-164-1A5 V-164-1C25 V-164-1C5 V-165-1A5 V-165-1C25 V-165-1C5 V-166-1A5 V-166-1C25 V-166-1C5 V-16-1AR5 V-16-1C2R5 --V-16-2AR5 V-16-2C2R5 --V-16-3AR5 V-16-3C2R5 --V-161-1AR5 V-161-1C2R5 --V-162-1AR5 V-162-1C2R5 --V-163-1AR5 V-163-1C2R5 --V-164-1AR5 V-164-1C2R5 --V-165-1AR5 V-165-1C2R5 --V-166-1AR5 V-166-1C2R5 --- V-16-1AL5 V-16-1C2L5 --V-16-2AL5 V-16-2C2L5 --V-16-3AL5 V-16-3C2L5 --V-161-1AL5 V-161-1C2L5 --V-162-1AL5 V-162-1C2L5 --V-163-1AL5 V-163-1C2L5 --V-164-1AL5 V-164-1C2L5 --V-165-1AL5 V-165-1C2L5 --V-166-1AL5 V-166-1C2L5 --- 11 A (OF: 100 gf) Without barrier Common terminal position Bottom Contact form SPDT Terminal style A C2 C A C2 C A C2 C A C2 C A C2 C A C2 C A C2 C Actuator Pin plunger Short hinge lever Hinge lever Long hinge lever Simulated roller lever Short hinge roller lever Hinge roller lever V-11-1A4 V-11-1C24 V-11-1C4 V-111-1A4 V-111-1C24 V-111-1C4 V-112-1A4 V-112-1C24 V-112-1C4 V-113-1A4 V-113-1C24 V-113-1C4 V-114-1A4 V-114-1C24 V-114-1C4 V-115-1A4 V-115-1C24 V-115-1C4 V-116-1A4 V-116-1C24 V-116-1C4 Note: 1. Add "G" to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add "-K" to the part number in the appropriate location to obtain 2.9 mm mounting holes. Examples: 1) V-16G3-1C25-K 2) V-11G-1A4-K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. Snap Action Switch V 123 Thermosetting Case Standard models - 15 A / 10 A Common Contact terminal form position Bottom SPDT SPST-NC SPST-NO Side Bottom SPDT SPST-NC SPST-NO SPDT Terminal style Actuator 15 A 10 A 200 gf A C2 C A C2 A C2 C A Pin plunger A C2 A C2 A C2 Short hinge lever Hinge lever Long hinge lever A C2 A C2 Simulated roller lever Short hinge roller lever A C2 Hinge roller lever 200 gf 100 gf V-15G-1A5-K V-15G-1C25-K V-15G-1C5-K V-15G-2A5-K V-15G-2C25-K V-15G-3A5-K V-15G-3C25-K V-15G-3C5-K V-15G-4A5-K V-15G-5A5-K V-15G-6A5-K V-15G1-1A5-K V-15G1-1C25-K V-15G2-1A5-K V-15G2-1C25-K V-15G3-1A5-K V-15G3-1C25-K V-10G-1A5-K V-10G-1C25-K -- V-10G-2A5-K V-10G-2C25-K V-10G-3A5-K V-10G-3C25-K -- V-10G-4A5-K V-10G-5A5-K V-10G-6A5-K V-10G1-1A5-K V-10G1-1C25-K V-10G2-1A5-K V-10G2-1C25-K V-10G3-1A5-K V-10G3-1C25-K V-10G-1A4-K V-10G-1C24-K -- V-10G-2A4-K V-10G-2C24-K V-10G-3A4-K V-10G-3C24-K -- V-10G-4A4-K V-10G-5A4-K V-10G-6A4-K V-10G1-1A4-K V-10G1-1C24-K V-10G2-1A4-K V-10G2-1C24-K V-10G3-1A4-K V-10G3-1C24-K V-15G4-1A5-K V-15G4-1C25-K V-15G5-1A5-K V-15G5-1C25-K V-10G4-1A5-K V-10G4-1C25-K V-10G5-1A5-K V-10G5-1C25-K V-10G4-1A4-K V-10G4-1C24-K V-10G5-1A4-K V-10G5-1C24-K V-15G6-1A5-K V-15G6-1C25-K V-10G6-1A5-K -- V-10G6-1A4-K V-10G6-1C24-K Note: 1. For SPST-NC and SPST-NO with levers consult Omron. 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. Heat Resistant Models (Up to 150C) - 15 A / 10A Common terminal position Bottom Contact form SPDT Terminal style Actuator 15 A 200 gf Solder Terminals (A) 10 A 100 gf Pin plunger V-15-1A5-T V-10-1A4-T Short hinge lever V-151-1A5-T V-101-1A4-T Hinge lever V-152-1A5-T V-102-1A4-T Long hinge lever V-153-1A5-T V-103-1A4-T Simulated roller lever V-154-1A5-T V-104-1A4-T Short hinge roller lever V-155-1A5-T V-105-1A4-T Hinge roller lever V-156-1A5-T V-106-1A4-T Note: 1. Add "G" to the part number in the appropriate location to obtain a 0.5 mm contact gap. Add "-K" to the part number in the appropriate location to obtain 2.9 mm mounting holes. Add "C2" to the part number in the appropriate location to obtain versions with #187 quickconnect terminals. Example: 1) V-15G1-1C25-T-K 2. Not all combinations are available. Consult Omron regarding nomenclature combinations and part numbers not found in this datasheet. 124 Snap Action Switch V Specifications Ratings (reference values) Type V-21 V-16 V-15 V-11 V-10 Rated voltage 250 VAC 8 VDC 30 VDC 125 VDC 250 VDC 250 VAC 8 VDC 30 VDC 125 VDC 250 VDC 250 VAC 8 VDC 30 VDC 125 VDC 250 VDC 250 VAC 8 VDC 30 VDC 125 VDC 250 VDC 250 VAC 8 VDC 30 VDC 125 VDC 250 VDC Non-inductive load Resistive load Lamp load NC NO NC NO 21 A 3A 21 A 5A 14 A 5A 0.6 A 0.1 A 0.3 A 0.05 A 16 A 2A 16 A 4A 10 A 4A 0.6 A 0.1 A 0.3 A 0.05 A 15 A 2A 15 A 4A 10 A 4A 0.6 A 0.1 A 0.3 A 0.05 A 11 A 1.5 A 11 A 3A 6A 3A 0.6 A 0.1 A 0.3 A 0.05 A 10 A 1.5 A 10 A 3A 6A 3A 0.6 A 0.1 A 0.3 A 0.05 A Inductive load Inductive load Motor load NC NO NC NO 12 A 4A 12 A 7A 12 A 5A 0.6 A 0.1 A 0.3 A 0.05 A 10 A 3A 10 A 6A 10 A 4A 0.6 A 0.1 A 0.3 A 0.05 A 10 A 3A 10 A 6A 10 A 4A 0.6 A 0.1 A 0.3 A 0.05 A 6A 2A 6A 3A 6A 3A 0.6 A 0.1 A 0.3 A 0.05 A 6A 2A 6A 3A 6A 3A 0.6 A 0.1 A 0.3 A 0.05 A Note: 1. The above current values are the normal current values of models with a contact gap of 1 mm (gap F), which vary with the normal current values of models with a contact gap of 0.5 mm (gap G). 2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7 ms max. (DC). 3. Lamp load has an inrush current of 10 times the steady-state current. 4. Motor load has an inrush current of 6 times the steady-state current. 5. The ratings values apply under the following test conditions: Ambient temperature: 202C, Ambient humidity: 655%, Operating frequency: 30 operations/min Approved Standards UL1054 (File No. E41515) CSA C22.2 No.55 (File No. LR21642) Rated voltage 125 VAC 250 VAC 125 VDC 250 VDC V-21 V-16 V-15 V-11 V-10 21 A, 1/2 HP 16 A, 1/2 HP 15 A, 1/2 HP 11 A, 1/3 HP 10 A, 1/3 HP 0.6 A 0.3 A EN 61058-1 (File No. 129608, VDE approval) Rated voltage 250 VAC V-21 20 (4) A V-16 16 (4) A EN 61058-1 (File No. T9451451, TUV Rheinland approval) V-11 11 (3) A Testing conditions: 5E4 (50,000 operations), T105 (0C to 105C) Rated voltage 250 VAC 250 VDC V-15 15 A V-10 10 A 0.3 A Testing conditions: 5E4 (50,000 operations), T85 (0C to 85C) Snap Action Switch V 125 Characteristics Operating speed Operating frequency 0.1 mm to 1 m/s (plunger models) Mechanical: 600 operations/minute, max. Electrical: 30 operations/minute, max. 100 M min. (at 500 VDC) 15 m max. 1,000 VAC, 50/60 Hz for 1 min between terminals of the same polarity V-21, V-16 and V-11: 2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts V-15 and V-10: 1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts Malfunction: 10 to 55 Hz, 1.5-mm double amplitude Destruction: 1,000 m/s2 (approx. 100G) max. Malfunction: V-21/V-16/V-15: 300 m/s2 (approx. 30G) max. Insulation resistance Contact resistance Dielectric strength (see note 2) Vibration resistance (see note 3) Shock resistance (see note 3) V-11/V10: 200 m/s2 (approx. 20G) max. Mechanical: 50,000,000 operations min. (60 operations/minute) Life expectancy Electrical: V-21/V-16/V-15: 100,000 operations min. (30 operations/minute) (V-15 heat resistive: 20,000 operations min. (30 ops/minute)) V-11/V-10: 300,000 operations min. (30 operations/minute) (V-10 heat resistive: 50,000 operations min. (30 ops/minute)) Degree of protection Degree of protection against electric shock Proof tracking index (PTI) Ambient operating temperature IEC IP40 Class I 175 -25C to 80C (at 60% RH max.) with no icing Ambient operating humidity Weight -25C to 150C for heat resistive models (at 60% RH max.) with no icing. 85% max. (for 5C to 35C) Approx. 6.2 g (plunger models) Note: 1. Data shown are of initial value. 2. The dielectric strength shown is measured using a separator between the switch and metal mounting plate. 3. For pin plunger models, the above values apply for use at both the free position and total travel position. For lever models, they apply at the total travel position. 4. For testing conditions, contact your OMRON sales representative. Contact Specifications Item Contact V-21 V-16 V-15 Specification Material V-10 Silver alloy Gap (standard value) Inrush current V-11 Rivet NC 1 mm (F gap type) or 0.5 mm (G gap type) 50 A max. NO Minimum applicable load Silver 40 A max. 36 A max. 24 A max. 160 mA at 5 VDC Note: Minimum applicable loads are indicated by N standard reference values. This value represents the failure rate at a 60% (60) reliability level (JIS C5003). The equation 60=0.5 x 10-6 / operations indicates that a failure rate of 1/2,000,000 operations can be expected at a reliability level of 60% 126 Snap Action Switch V Engineering Data Mechanical service life Electrical service life (Pin plunger models) (Pin plunger models) V-10 (0.98 N {100 gf}), V-11 100 50 V-10 (1.96 N {200 gf}) V-15 V-16 V-21 0.01 0 0.2 0.4 Full stroke OT rated value 0.6 0.8 1.0 1.2 1.4 (1.6) 1.8 Operating frequency: 60 operations/min cos = 1, 250 VAC 2 1 0.5 V-21 0.3 V-15 V-16 0.1 0 OT (mm) 8 12 16 20 24 2 Ambient temperature: 202C Ambient humidity: 655% Operating frequency: 60 operations/min cos = 1, 250 VAC 1 0.5 0.3 0 28 V-10 V-11 0.1 0.5 1 2 3 4 5 6 7 8 9 10 11 12 Switching current (A) Barrier direction (V-21 and V-16) Right-hand Barrier Contact form SPDT 4 5 Switching current (A) Contact Form Common terminal position 6 6 5 Number of operations (x10 ) 200 Number of operations (x10 ) 6 Number of operations (x10 ) Ambient temperature: 202C Ambient humidity: 655% Without load Operating frequency: 600 operations/min 10 V-11/-10 V-21/-16/-15 V-21/-16/-15/-10 SPST-NC* Left-hand Barrier SPST-NO* Bottom type Side type Mounting Holes All switches may be panel mounted using M3 mounting screws with plane washers or spring washers to securely mount the switch. Tighten the screws to a torque of 0.39 to 0.59 N*m. * The SPST-NC and SPST-NO contact form types listed in the ordering information tables are for Pin Plunger models only. For information concerning lever models consult Omron. Two, 3.1-dia. mounting holes or M3 screw holes 10.3 0.1 22.2 0.1 Snap Action Switch V 127 Dimensions Terminals Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions 2. The following table is for the SPDT contact specifications. Two terminals will be available for SPST-NO or SPST-NC contact specifications. For terminal positions, refer to the above Contact Form 3. Right-angle PCB terminal type is available with some models (not shown). Drawings will be provided if requested. D5: Pins at right angles, to the right D6: Pins at right angle, to the left Terminal type Solder Terminal (A) COM bottom position (5.5) (4.9) (6.5) (6.5) (7.7) 2.9 2.9 3.2 Note: 128 t = 0.8 (12.0) Three, quick-connect terminals (#250) (5.5) (4.9) (6.5) (6.5) (7.7) 2.4 2.4 3.6 (12.0) (10) 6.35 3.2 (see note) 6.35 3.2 4.750.1 4.750.1 2.4 dia. 1.6 dia. Indicates the length to the center of the 1.6-dia. holes Snap Action Switch t = 0.5 (10) Three, quick-connect terminals (#187) (5.5) (10) Terminal dimensions Quick-connect Terminal (#250) (C) (5.5) (10) t = 0.5 Three, solder terminals COM side position Quick-connect Terminal (#187) (C2) V 1.6-dia. terminal hole 8.1 3.95 6.350.1 1.65-dia. terminal hole Dimensions and Operating Characteristics Thermoplastic Case Models Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions 2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2, which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals. 3. The @ in the model number is for the terminal code. 4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix "K" have a hole size of 2.9 mm. 5. The operating characteristics are for operation in the A direction ( ). Pin Plunger Models (Without Barrier) V-21-1 6 V-16-1 5 V-11-1 4 20.20.25 A 1.6 PT +0.13 3.1 -0.03 dia. holes 4.2 2.8 0.6 2.8 2.8 2.8 OP 8.4 10.30.1 15.9 19.1 +0.13 3.1 -0.03 3.40.15 dia. 22.20.1 2.8 (12.0) 27.8 t=0.8 Three, quick-connect terminals (#250) 10.3 Characteristics 39.80.8 V-21-1@6 V-16-1@5 OF max. 400 gf 200 gf RF min. 80 gf 1.2 mm OT min. 1.0 mm MD max. 0.4 mm 14.7 0.4 mm OP (With Right-hand Barrier) V-21-1 R6 V-16-1 R5 A PT 50 gf PT max. 20.20.25 +0.13 3.1 -0.03 dia. holes 2.8 4.2 1.6 0.6 2.8 2.8 2.8 OP 8.4 10.30.1 15.9 19.1 Characteristics 21.9 +0.13 3.1 -0.03 0.6 3.40.15 dia. 22.20.1 2.8 27.8 t=0.8 Three, quick-connect (12.0) terminals (#250) 10.3 (With Left-hand Barrier) +0.13 2.8 3.1 -0.03 dia. holes 1.6 20 gf 50 gf PT max. 1.2 mm OT min. 1.0 mm 0.4 mm 14.7 0.4 mm A 2.8 PT 2.8 19.1 21.9 20.20.25 2.8 0.6 200 gf RF min. OP 40.2 4.2 V-11-1@5 100 gf MD max. 39.80.8 V-21-1 L6 V-16-1 L5 V-11-1@4 OF max. 8.4 15.9 10.30.1 OP +0.13 3.1 -0.03 t=0.8 Three, quick-connect terminals (#250) 0.6 10.3 3.40.15 dia. (12.0) 2.8 22.20.1 27.8 39.80.8 40.2 Snap Action Switch V 129 Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions 2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2, which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals. 3. The @ in the model number is for the terminal code. 4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix "K" have a hole size of 2.9 mm. 5. The operating characteristics are for operation in the A direction ( ). Short Hinge Lever Models V-211-1 6 V-161-1 5 V-111-1 4 22.1 A PT 2.8 t = 0.5 (see note) Characteristics V-211-1@6 V-161-1@5 V-111-1@4 8.1 3.1 +0.13 -0.03 1.6 4.3 dia. holes 0.6 2.8 2.8 OP 10.30.1 8.4 15.9 19.1 OF max. 400 gf 200 gf 100 gf RF min. 50 gf 50 gf 15 gf PT max. 1.6 mm OT min. 0.8 mm MD max. +0.13 3.1 -0.03 3.40.15 dia. 0.6 mm 15.2 0.5 mm OP t=0.8 Three, quick-connect terminals (#250) 22.20.1 2.8 (12.0) 27.8 39.80.8 Note: 10.3 Stainless-steel lever Hinge Lever Models V-212-1 6 V-162-1 5 V-112-1 4 35.60.8 PT 8.1 t = 0.5 (see note) A 1.6 Characteristics V-212-1@6 V-162-1@5 V-112-1@4 +0.13 3.1 -0.03 dia. holes 4.3 0.6 2.8 2.8 2.8 OP 8.4 10.30.1 15.9 19.1 +0.13 OF max. 250 gf 125 gf 60 gf RF min. 25 gf 14 gf 6 gf PT max. 4.0 mm OT min. 1.6 mm MD max. 3.1 -0.03 3.40.15 dia. 22.20.1 (12.0) 2.8 27.8 39.80.8 t=0.8 Three, quick-connect terminals (#250) Note: 1.5 mm 15.2 1.2 mm OP 10.3 Stainless-steel lever Long Hinge Lever Models V-213-1 6 V-163-1 5 V-113-1 4 59.40.8 A PT 2.8 1.6 +0.13 3.1 -0.03 dia. holes t = 0.5 (see note) 2.8 OP 8.4 15.9 10.30.1 Characteristics V-213-1@6 V-163-1@5 V-113-1@4 4.3 0.6 2.8 OF max. 130 gf 70 gf 35 gf RF min. 12 gf 6 gf --- PT max. 19.1 OT min. +0.13 3.1 -0.03 3.40.15 dia. 22.20.1 2.8 27.8 39.80.8 130 Snap Action Switch V (12.0) t=0.8 Three, quick-connect terminals (#250) Note: MD max. 10.3 Stainless-steel lever OP 9.0 mm 2.0 mm 3.2 mm 2.8 mm +2.6 15.2 -3.2 mm 15.2 2.6 mm Note: 1. Unless otherwise specified, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions 2. The following illustrations and drawings are for quick-connect terminals (#250) (terminals C). V models also incorporate terminals A and C2, which are omitted from the following drawings. Refer to Terminals section for the dimensions of these terminals. 3. The @ in the model number is for the terminal code. 4. The illustrations for V-21, V-16 and V-11 show a hole size of 3.1 mm. V-21, V-16 and V-11 models with a suffix "K" have a hole size of 2.9 mm. 5. The operating characteristics are for operation in the A direction ( ). Simulated Roller Lever Models V-214-1 6 V-164-1 5 V-114-1 4 32.60.8 3.5R PT OP A Characteristics V-214-1@6 V-164-1@5 V-114-1@4 8.1 t = 0.5 (see note) 1.6 3.1 +0.13 -0.03 dia. holes 4.3 2.8 0.6 2.8 2.8 8.4 15.9 10.30.1 19.1 OF max. 250 gf 125 gf 60 gf RF min. 25 gf 14 gf 6 gf PT max. 4.0 mm OT min. 1.6 mm MD max. +0.13 3.1 -0.03 1.5 mm 18.7 1.2 mm OP 3.40.15 dia. 22.20.1 2.8 27.8 t=0.8 Three, quick-connect terminals (#250) (12.0) 10.3 39.80.8 Note: Stainless-steel lever Short Hinge Roller Lever Models V-215-1 6 V-165-1 5 V-115-1 4 Characteristics V-215-1@6 V-165-1@5 V-115-1@4 20.1 A t = 0.5 (see 8.1 note 1) PT 1.6 +0.13 3.1 -0.03 5.1 0.6 4.8 dia. x 4.8 (see note 2) dia. holes 2.8 2.8 OP 8.4 15.9 10.30.1 OF max. 480 gf 240 gf 120 gf RF min. 50 gf 50 gf 15 gf PT max. 1.6 mm OT min. 0.8 mm MD max. 19.1 0.6 mm 20.7 0.6 mm OP +0.13 3.1 -0.03 3.40.15 dia. 22.20.1 27.8 2.8 t=0.8 Three, quick-connect terminals (#250) (12.0) 39.80.8 Note: 10.3 1. Stainless-steel lever 2. Oilless polyacetar resin roller Hinge Roller Lever Models V-216-1 6 V-166-1 5 V-116-1 4 34.00.8 PT A t = 0.5 (see note 1) 8.1 1.6 0.6 dia. holes 2.8 OP 2.8 10.30.1 Characteristics V-216-1@6 V-166-1@5 V-116-1@4 5.1 +0.13 3.1 -0.03 8.4 4.8 dia. x 4.8 (see note 2) 15.9 19.1 +0.13 OF max. 250 gf 125 gf 60 gf RF min. 25 gf 14 gf 6 gf PT max. 4.0 mm OT min. 1.6 mm MD max. 3.1 -0.03 3.40.15 dia. 22.20.1 2.8 27.8 39.80.8 10.3 t=0.8 (12.0) Three, quick-connect terminals (#250) Note: OP 1.5 mm 20.7 1.2 mm 1. Stainless-steel lever 2. Oilless polyacetar resin roller Snap Action Switch V 131 Thermosetting Case Models Unless otherwise specified, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals. The @ in the model number is for the terminal code. The illustrations show models with a suffix "K", which have a hole size of 2.9 mm. Omit the "K" to obtain models with hole size = 3.1 mm. The operating characteristics are for operation in the A direction ( ). Note: 1. 2. 3. 4. 5. Pin Plunger Models 20.20.25 V-15G-1 5-K V-10G-1 5-K V-10G-1 4-K 4.2 PT 2.8 A OP 2.8 Characteristics +0.13 2.9 -0.03 dia. holes V-15G-1@5-K V-10G-1@5-K V-10G-1@4-K 100 gf 2.8 OF max. 200 gf 10.30.1 RF min. 50 gf 15.9 18.8 +0.13 3.1 -0.03 3.40.15 dia. 22.20.1 2.8 27.8 10.3 t=0.5 Three, solder terminals (10) 20 gf PT max. 1.2 mm OT min. 1.3 mm MD max. 0.3 mm 14.7 0.4 mm OP 37.80.8 Short Hinge Lever Models t = 0.5 (see note) 22.1 V-15G1-1 5-K V-10G1-1 5-K V-10G1-1 4-K PT A 4.3 2.8 +0.13 Characteristics 2.9 -0.03 dia. holes 8.1 V-15G1-1@5-K V-10G1-1@5-K V-10G1-1@4-K 100 gf 2.8 OF max. 200 gf 10.30.1 RF min. 50 gf OP 15.9 18.8 +0.13 3.1 -0.03 3.40.15 dia. 22.20.1 27.8 2.8 10.3 t=0.5 Three, solder terminals 15 gf PT max. 1.5 mm OT min. 1.0 mm MD max. 0.5 mm 15.2 0.5 mm OP (10) 37.80.8 Note: Stainless-steel lever Hinge Lever Models t = 0.5 (see note) V-15G2-1 5-K V-10G2-1 5-K V-10G2-1 4-K 35.60.8 PT 4.3 8.1 2.8 OP 10.30.1 V-15G2-1@5-K V-10G2-1@5-K V-10G2-1@4-K OF max. 125 gf 60 gf RF min. 14 gf Characteristics +0.13 2.9 -0.03 dia. holes A 15.9 18.8 3.1 +0.13 -0.03 2.8 3.3 mm OT min. 2.3 mm MD max. 3.40.15 dia. 10.3 22.20.1 2.8 t=0.5 Three, solder terminals 6 gf PT max. OP 0.8 mm +2.6 15.2 -3.2 mm 15.2 1.2 mm 27.8 (10) Note: Stainless-steel lever 37.80.8 Long Hinge Lever Models V-15G3-1 5-K V-10G3-1 5-K V-10G3-1 4-K A PT OP 2.8 t = 0.5 (see note) 59.40.8 8.1 +0.13 2.9 -0.03 dia. holes 4.3 2.8 10.30.1 15.9 18.8 +0.13 3.1 -0.03 2.8 3.40.15 dia. 22.20.1 27.8 37.80.8 132 Snap Action Switch V (10) 10.3 t=0.5 Three, solder terminals Note: Stainless-steel lever Characteristics V-15G3-1@5-K V-10G3-1@5-K V-10G3-1@4-K OF max. 70 gf 35 gf RF min. 6 gf - - - gf PT max. 9.0 mm 7.6 mm OT min. 3.0 mm MD max. OP 3.2 mm 2.0 mm 15.2 2.6 mm Unless otherwise specified, all units are in millimeters and a tolerance of 0.4 mm applies to all dimensions The following illustrations are for quick-connect terminals (#250) (terminals C). Refer to Terminals section for the dimensions of other terminals. The @ in the model number is for the terminal code. The illustrations show models with a suffix "K", which have a hole size of 2.9 mm. Omit the "K" to obtain models with hole size = 3.1 mm. The operating characteristics are for operation in the A direction ( ). Note: 1. 2. 3. 4. 5. Simulated Roller Lever Models 3.5R V-15G4-1 5-K V-10G4-1 5-K V-10G4-1 4-K t = 0.5 (see note) A PT V-10G4-1@4-K OF max. 125 gf 60 gf RF min. 14 gf 2.9 -0.03 dia. holes 8.1 2.8 2.8 OP V-15G4-1@5-K V-10G4-1@5-K Characteristics 4.3 +0.13 32.60.8 10.30.1 15.9 18.8 3.1 +0.13 -0.03 2.8 22.20.1 27.8 (10) 37.80.8 3.3 mm OT min. 2.3 mm MD max. 10.3 3.40.15 dia. t=0.5 Three, solder terminals Note: 6 gf PT max. 0.8 mm 18.7 1.2 mm OP Stainless-steel lever Short Hinge Roller Lever Models V-15G5-1 5-K V-10G5-1 5-K V-10G5-1 4-K 4.8 dia. x 4.8 (see note 2) t = 0.5 (see note 1) A 5.1 20.1 +0.13 2.9 -0.03 dia. holes 8.1 PT OP 2.8 10.30.1 15.9 18.8 3.1 +0.13 -0.03 2.8 3.40.15 dia. 22.20.1 27.8 V-10G5-1@4-K OF max. 240 gf 120 gf RF min. 50 gf 1.5 mm OT min. 1.0 mm 0.5 mm 20.7 0.6 mm OP t=0.5 Three, solder terminals 15 gf PT max. MD max. 10.3 (10) V-15G5-1@5-K V-10G5-1@5-K Characteristics 37.80.8 Note: 1. Stainless-steel lever 2. Oilless polyacetar resin roller Hinge Roller Lever Models V-15G6-1 5-K V-10G6-1 5-K V-10G6-1 4-K 4.8 dia. x 4.8 (see note 2) t = 0.5 (see note 1) A 34.00.8 PT 8.1 OP 2.9 +0.13 -0.03 5.1 dia. holes 2.8 10.30.1 15.9 18.8 +0.13 3.1 -0.03 2.8 3.40.15 dia. 22.20.1 27.8 (10) 10.3 t=0.5 Three, solder terminals V-15G6-1@5-K V-10G6-1@5-K V-10G6-1@4-K OF max. 125 gf 60 gf RF min. 14 gf Characteristics 6 gf PT max. 3.3 mm OT min. 2.3 mm MD max. OP 0.8 mm 20.7 1.6 mm 37.80.8 Note: 1. Stainless-steel lever 2. Oilless polyacetar resin roller Accessories Refer to the "V/VX/D3C Common Accessories" datasheet for information regarding VAL, VAM and VAV external actuators (sold separately). Snap Action Switch V 133 Precautions Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User's Guide, "Snap Action Switches, Technical Information" for correct use. Correct Use Cautions Terminal Connection Insulation Distance To solder the lead to the solder terminal, apply a soldering iron rated at 60 W max. quickly (within 5 seconds) with the actuator at the free position. According to EN61058-1, the minimum insulation thickness for this switch should be 1.1 mm and minimum clearance distance between the terminal and mounting plate should be 1.0 mm. If the insulation distance cannot be provided in the product incorporating the switch, either use a switch with insulation barrier or use a separator to ensure sufficient insulation distance. Note that applying a soldering iron for too long a time or using one that is rated at more than 60 W may degrade the switch characteristics. Use an appropriate mating connector for #187 or #250 quick connect terminals. Specifications Approved by TUV Rheinland According to EN61058-1 Appropriate Cable Size (mm2) Model Solder terminal V-10 0.75, 1.25, 2.0 V-15 1.25, 2.0 Operation Make sure that the operating body pushes the switch actuator with an adequate force when the switch is to be operated, and that it does not touch the actuator when the switch is released. Do not change the operating position by modifying the actuator. Do not use the switch in a application where the operating speed is extremely slow or the actuator is set in the midpoint between the free position and operating position. Install the pin plunger switch so that the operating force is applied in alignment with the stroke of the actuator. The switch should be set so that its stroke is in the range of 60 to 90% of the rated OT (minimum value) when the switch has been operated. 134 Snap Action Switch V MEMO Snap Action Switch V All sales are subject to Omron Electronic Components LLC standard terms and conditions of sale, which can be found at http://www.components.omron.com/components/web/webfiles.nsf/sales_terms.html ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. OMRON ON-LINE OMRON ELECTRONIC COMPONENTS LLC Global - http://www.omron.com USA - http://www.components.omron.com 55 E. Commerce Drive, Suite B Schaumburg, IL 60173 847-882-2288 Cat. No. X303-E-1 11/10 Snap Action Switch V Specifications subject to change without notice Printed in USA