SN74LVC2G07-EP www.ti.com ....................................................................................................................................................................................................... SCES719 - MAY 2008 DUAL BUFFER/DRIVER WITH OPEN-DRAIN OUTPUTS FEATURES 1 * * * * * * (1) * Controlled Baseline - One Assembly Site - One Test Site - One Fabrication Site Extended Temperature Performance of -55C to 125C Enhanced Diminishing Manufacturing Sources (DMS) Support Enhanced Product-Change Notification Qualification Pedigree (1) Supports 5-V VCC Operation * * * * * * * Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits. * Inputs and Open-Drain Outputs Accept Voltages up to 5.5 V Max tpd of 5.7 ns at 3.3 V Low Power Consumption, 10 A Max ICC 24-mA Output Drive at 3.3 V Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25C Typical VOHV (Output VOH Undershoot) >2 V at VCC = 3.3 V, TA = 25C Ioff Supports Partial-Power-Down Mode Operation Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) DCK PACKAGE (TOP VIEW) 1A 1 6 1Y GND 2 5 VCC 2A 3 4 2Y See mechanical drawings for dimensions. DESCRIPTION/ORDERING INFORMATION This dual buffer/driver is designed for 1.65-V to 5.5-V VCC operation. The output of the SN74LVC2G07 is open drain and can be connected to other open-drain outputs to implement active low wired OR or active high wired AND functions. The maximum sink current is 32 mA. This device is fully specified for partial power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. ORDERING INFORMATION (1) PACKAGE (2) TA -55C to 125C (1) (2) SOT (SC-70) - DCK ORDERABLE PART NUMBER Reel of 250 SN74LVC2G07MDCKTEP TOP-SIDE MARKING CHC For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2008, Texas Instruments Incorporated SN74LVC2G07-EP SCES719 - MAY 2008 ....................................................................................................................................................................................................... www.ti.com FUNCTION TABLE (EACH BUFFER/DRIVER) INPUT A OUTPUT Y H H L L LOGIC DIAGRAM (POSITIVE LOGIC) 1A 2A 1 6 3 4 1Y 2Y Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT VCC Supply voltage range -0.5 6.5 V VI Input voltage range (2) -0.5 6.5 V VO Voltage range applied to any output in the high-impedance or power-off state (2) -0.5 6.5 V (2) (3) VO Voltage range applied to any output in the high or low state 6.5 V IIK Input clamp current VI < 0 -0.5 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current 50 mA Continuous current through VCC or GND JA Package thermal impedance (4) Tstg Storage temperature range (1) (2) (3) (4) 2 DCK package -65 100 mA 259 C/W 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. The value of VCC is provided in the recommended operating conditions table. The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): SN74LVC2G07-EP SN74LVC2G07-EP www.ti.com ....................................................................................................................................................................................................... SCES719 - MAY 2008 Recommended Operating Conditions VCC Operating Supply voltage Data retention only 1.65 5.5 1.7 VCC = 3 V to 3.6 V 0.7 x VCC 0.35 x VCC VCC = 1.65 V to 1.95 V Low-level input voltage V V 2 VCC = 4.5 V to 5.5 V VIL UNIT 0.65 x VCC VCC = 2.3 V to 2.7 V High-level input voltage MAX 1.5 VCC = 1.65 V to 1.95 V VIH MIN VCC = 2.3 V to 2.7 V 0.7 VCC = 3 V to 3.6 V 0.8 V 0.3 x VCC VCC = 4.5 V to 5.5 V VI Input voltage 0 5.5 V VO Output voltage 0 5.5 V VCC = 1.65 V 4 VCC = 2.3 V IOL t/v Low-level output current 8 16 VCC = 3 V Input transition rise or fall rate VCC = 4.5 V 24 VCC = 1.8 V 0.15 V, 2.5 V 0.2 V 20 VCC = 3.3 V 0.3 V 10 VCC = 5 V 0.5 V TA mA 24 ns/V 5 Operating free-air temperature -55 125 C MAX UNIT Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS IOL = 100 A VOL VCC IOL = 4 mA 1.65 V 0.45 IOL = 8 mA 2.3 V 0.3 IOL = 16 mA 0.4 3V IOL = 24 mA A inputs TYP 0.1 IOL = 24 mA II MIN 1.65 V to 5.5 V 0.55 4.5 V VI = 5.5 V or GND Ioff VI or VO = 5.5 V ICC VI = 5.5 V or GND, IO = 0 ICC One input at VCC - 0.6 V, Other inputs at VCC or GND Ci VI = VCC or GND V 0.55 0 to 5.5 V 5 A 0 10 A 1.65 V to 5.5 V 10 A 500 A 3 V to 5.5 V 3.3 V 3.5 Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): SN74LVC2G07-EP pF 3 SN74LVC2G07-EP SCES719 - MAY 2008 ....................................................................................................................................................................................................... www.ti.com Switching Characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A Y VCC = 3.3 V 0.3 V VCC = 5 V 0.5 V MIN MAX MIN MAX 1 5.7 0.5 4.9 UNIT ns Operating Characteristics TA = 25C PARAMETER Cpd 4 Power dissipation capacitance TEST CONDITIONS f = 10 MHz Submit Documentation Feedback VCC = 3.3 V VCC = 5 V TYP TYP 4 4 UNIT pF Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): SN74LVC2G07-EP SN74LVC2G07-EP www.ti.com ....................................................................................................................................................................................................... SCES719 - MAY 2008 PARAMETER MEASUREMENT INFORMATION (OPEN DRAIN) VLOAD S1 RL From Output Under Test Open GND CL (see Note A) RL TEST S1 tPZL (see Notes E and F) tPLZ (see Notes E and G) tPHZ/tPZH VLOAD VLOAD VLOAD LOAD CIRCUIT INPUTS VCC 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 5 V 0.5 V VI tr/tf VCC VCC 3V VCC 2 ns 2 ns 2.5 ns 2.5 ns VM VLOAD CL RL V VCC/2 VCC/2 1.5 V VCC/2 2 x VCC 2 x VCC 6V 2 x VCC 30 pF 30 pF 50 pF 50 pF 1 k 500 500 500 0.15 V 0.15 V 0.3 V 0.3 V VI Timing Input VM 0V tW tsu VI Input VM VM th VI Data Input VM VM 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VI VM Input VM 0V tPLH VOH Output VM VOL tPHL VM VM 0V tPLZ Output Waveform 1 S1 at VLOAD (see Note B) tPLH VLOAD/2 VM tPZH VOH Output VM tPZL tPHL VM VI Output Control VM VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VOL + V VOL tPHZ VM VOH - V VOH 0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators have the following characteristics: PRR 10 MHz, ZO = 50 . D. The outputs are measured one at a time, with one transition per measurement. E. Because this device has open-drain outputs, tPLZ and tPZL are the same as tPD. F. tPZL is measured at VM. G. tPLZ is measured at VOL + V. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): SN74LVC2G07-EP 5 PACKAGE MATERIALS INFORMATION www.ti.com 13-Jul-2011 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74LVC2G07MDCKTEP Package Package Pins Type Drawing SC70 DCK 6 SPQ 250 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 180.0 8.4 Pack Materials-Page 1 2.25 B0 (mm) K0 (mm) P1 (mm) 2.4 1.22 4.0 W Pin1 (mm) Quadrant 8.0 Q3 PACKAGE MATERIALS INFORMATION www.ti.com 13-Jul-2011 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74LVC2G07MDCKTEP SC70 DCK 6 250 202.0 201.0 28.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps RF/IF and ZigBee(R) Solutions www.ti.com/lprf TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated